SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4500-8
Electroreduction of CO2 to ethylene offers a promising route for renewable electricity storage, yet achieving high ethylene selectivity at industrial current densities remains challenging due to the large energy barrier for C–C coupling. Here, we report a “MOF-assisted in situ doping” strategy to introduce the oxophilic nonmetal phosphorus (P) into the copper oxide (CuO) lattice, constructing a localized Cu–P dual-site adsorption configuration for the key *OCCHO intermediate. The optimized catalyst delivers an impressive Faradaic efficiency of 64.6% for ethylene with a partial current density of 646 mA cm-2. Comprehensive structural characterizations demonstrate that P mainly occupies Cu sites, generating abundant lattice defects and oxygen vacancies. In situ synchrotron infrared spectroscopy and theoretical calculations reveal that P doping modulates the electronic structure of Cu, optimizes the binding energies of *CO and *CHO, and stabilizes *OCCHO via P–O/Cu–C dual-site adsorption, thereby significantly lowering the asymmetric C-C coupling energy barrier to 0.74 eV. This work highlights a dual-site microenvironment regulation strategy for CO2-to-ethylene electroreduction.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4436-0
Microwave-absorbing materials (MAMs) deployed on naval vessels, aerospace vehicles, and critical electronic systems face coupled electromagnetic, marine salt-spray corrosion, and extreme-temperature loads that legacy single-function absorbers cannot withstand. This review consolidates progress on three environmentally adaptive MAM classes: corrosion-protective, anti-icing, and thermal-management absorbers. The electromagnetic loss and impedance-matching fundamentals are first established, then the synergistic mechanisms, design strategies, and characterization protocols for each class are examined against representative material systems and their measured performance. The analysis identifies a shared design logic—multiscale hierarchical architecture, interfacial polarization engineering, and multifunctional phase integration—while distinguishing the divergent protection mechanisms: barrier and passivation effects for corrosion, surface-energy and latent-heat regulation for anti-icing, and phonon–electron transport decoupling for thermal management. Persistent bottlenecks include the trade-off between impedance matching and protective-layer density, the absence of standardized coupled-field test protocols, and the scarcity of long-term salt-spray and thermal-cycling durability data. Future directions are delineated: intelligent self-adaptive absorbers, multiphysics-coupled simulation frameworks, and environmentally benign multifunctional integration. The review provides a theoretical and technical basis for the design, construction, and engineering scale-up of next-generation high-performance absorbers for aerospace, electronic, and marine equipment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4435-9
Organic room-temperature phosphorescent (RTP) materials exhibit large Stokes shifts, high signal-to-noise ratios, and long emission lifetimes, positioning them as promising candidates for advanced anti-counterfeiting, bioimaging, sensing, and display technologies. Despite significant progress in molecular design—including radical-based systems, crystal engineering, host-guest doping, polymer matrix confinement, and supramolecular assembly—the integration of these materials with 3D printing remains in its infancy. This review critically examines the design strategies and research advances in 3D-printed organic RTP materials, focusing on the fundamental photophysical processes of intersystem crossing and suppression of non-radiative transitions. We analyze how printing parameters, matrix rheology, and layer-by-layer deposition influence phosphorescence quantum yields and lifetimes. Key challenges such as oxygen quenching, thermal degradation during extrusion, and poor interlayer adhesion are discussed with quantitative benchmarks. The review highlights that current 3D-printed RTP systems achieve lifetimes up to 1.2 s and quantum yields of 12% under ambient conditions, but scalability beyond 100 cm² remains limited by nozzle clogging and slow curing kinetics. By mapping material formulation to printability, we identify operational windows for extrusion-based and vat photopolymerization techniques. This work provides a roadmap for engineers to transition RTP materials from laboratory-scale demonstrations to industrial fabrication of complex 3D architectures with persistent luminescence.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4406-y
Covalent organic frameworks (COFs) are promising adsorbents for uranium extraction from complex aqueous environments due to their tunable pore structures and customizable functionalities. However, conventional bottom-up assembly routes yield frameworks with fixed dimensionality, where internal pores and buried functional sites remain inaccessible, limiting dynamic optimization for uranium capture. This study introduces a reversible coordination-directed clip-off strategy that enables dimensional programming of COFs through silver-nitrogen coordination bonds and thiosulfate/silver ion regulators. The approach allows controlled cleavage and reconstruction of coordination bonds, dynamically exposing hidden binding sites and adapting the framework to uranium extraction requirements. While the strategy demonstrates high-efficiency uranium extraction, it faces challenges including increased material and operating costs from silver-based regulators, potential structural fatigue from repeated cleavage-reconstruction cycles, and limited validation beyond laboratory scale. The reversible dimensional programming is generalizable to other reticular frameworks such as metal-organic frameworks (MOFs), enabling stimuli-responsive smart materials, controlled-release carriers, and adaptive separation membranes. Integration with machine learning and computational screening could accelerate rational design of functional active sites. This interdisciplinary approach offers a pathway toward intelligent, dimensionally morphing materials for energy and environmental sustainability, though optimization of regulating components and structural durability is required for practical scalability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4286-4
Multifunctional nanoplatforms capable of efficiently regulating both emerging and classical cell death mechanisms, thereby overcoming the adaptive resistance of malignant cells to certain cell death modalities, remain a significant challenge. Herein, we propose a new concept for the self-assembly of zinc-cystine coordination networks on curcumin (Cur) drug nanocrystals (DNCs) to construct Cur@PDA@GOx/Zn-Cys (CPGZC) nanoplatforms, enabling enhanced antitumor therapy through multicomponent synergistic modulation of both newly identified disulfidptosis and classical apoptosis. At tumor site, GOx-mediated glucose depletion reduces nicotinamide adenine dinucleotide phosphate (NADPH) levels, which can impair the intracellular conversion of cystine to cysteine. Combined with the exogenous cystine delivered by CPGZC NPs, rapid intracellular disulfide accumulation strongly activates disulfidptosis. Simultaneously, the reduction in NADPH levels inhibits GSH biosynthesis, augmenting the intracellular ROS levels elicited by Cur DNCs within the CPGZC nanoplatforms. Moreover, the elevated oxidative stress, in synergy with the excessive Zn2+ introduced, aggravates mitochondrial damage, thereby further amplifying apoptosis. Consequently, the synergistic modulation of disulfidptosis and apoptosis induces a potent antitumor response, as validated by comprehensive in vitro and in vivo investigations. This study opens new avenues for the development of multifunctional nanoplatforms for enhanced cancer therapy through the effective integration of both emerging and classical cell death mechanisms, which may serve as a promising strategy to advance our comprehension of synergistic utilization of various cell death mechanisms and combat with complex cancers.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4312-8
Carbazole phosphonic acid-based self-assembled molecules (SAMs) serve as effective hole-selective contacts in organic solar cells (OSCs), yet their molecular packing and aggregation behavior during solution processing remain difficult to control, limiting hole transport and device durability. This study introduces a polymer-templated self-assembly strategy to regulate molecular organization by one-step spin-coating a blend of [2-(9H-carbazol-9-yl)ethyl]phosphonic acid (2PACz) and PEDOT:PSS. The polycationic PEDOT+ framework acts as a template, providing supplementary anchoring interactions that promote ordered molecular arrangement and suppress unfavorable agglomeration. Pronounced face-on orientation and enhanced structural coherence of 2PACz within the polymer matrix are evidenced. The templated ordering improves vertical charge transport, interfacial homogeneity, and film morphology. In binary OSCs based on PM6:BTP-eC9, the hybrid hole transport layers (HTLs) yield a champion power conversion efficiency (PCE) of 20.26%, with an open-circuit voltage (VOC) of 0.874 V, a short-circuit current (JSC) of 28.97 mA cm-2, and a fill factor (FF) of 80.02%. Devices incorporating hybrid HTLs exhibit exceptional operational stability, retaining over 90% of initial PCE (T90) after 405 h of continuous operation at the maximum power point (MPP). This work establishes polymer-directed SAM assembly as a scalable route to simultaneously optimize nanoscale molecular packing, interfacial energetics, and long-term device stability for high-performance OSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4439-4
Silk fibroin (SF) hydrogels are promising for neural regeneration but suffer from progressive stiffening due to excessive β-sheet assembly, limiting their use in traumatic brain injury (TBI) repair. This study introduces a dopamine (DA)-mediated synergistic topological entanglement strategy to construct an SF-DA/gelatin-DA composite hydrogel (SG). The system integrates covalent cross-linking, net cationic electrostatic repulsion, hydrogen bonding, and π-π stacking to regulate SF assembly dynamics at the molecular level. The resulting SG hydrogel maintains stable mechanical softness over extended periods, with a storage modulus of approximately 1.2 kPa after 28 days, compared to a 5-fold increase in pure SF hydrogels. The sustained softness promotes neural stem cell (NSC) proliferation and differentiation, with a 2.5-fold increase in βIII-tubulin expression and a 1.8-fold increase in GFAP expression after 14 days. In a rat TBI model, SG hydrogel implantation reduced glial scar formation by 40% and improved neurological function scores by 30% at 8 weeks. The hydrogel degrades at a rate of 12% per week, matching tissue regeneration. This multi-crosslinking approach offers a clinically translatable strategy for neural tissue engineering, addressing the critical bottleneck of mechanical instability in SF-based biomaterials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4384-9
Nanovesicle-hybridized hydrogels constitute a class of bioactive materials that integrate the structural stability of polymer networks with the intrinsic biological functions of nanoscale vesicles. Conventional hydrogels suffer from swelling-induced mechanical degradation, uncontrollable cargo release, and an inability to integrate multiple bioactivities. Hybridization with nanovesicles provides a robust solution to these limitations. This review systematically delineates the evolution of construction strategies, transitioning from simple physical entrapment to advanced chemical crosslinking involving noncovalent supramolecular interactions and covalent conjugation. We elucidate how these integration methods fundamentally enhance mechanical strength, enable spatiotemporally controlled release of vesicles and their cargos, and endow composite systems with multifaceted bioactivities. The diverse biomedical applications of these hybridized platforms in drug delivery, tissue engineering, and disease therapy are thoroughly discussed. Current technical hurdles in clinical translation and promising future directions are identified, providing a roadmap for the next generation of intelligent biomimetic materials. The review emphasizes that the shift from physical doping to chemical crosslinking represents a paradigm change, yielding composites with superior mechanical resilience and programmable release kinetics. By critically assessing the trade-offs between crosslinking density, vesicle integrity, and payload retention, this work offers a framework for designing hybrid systems with tailored properties. Key challenges include scalable manufacturing, long-term stability, and regulatory hurdles. The analysis underscores that clinical translation demands standardized protocols for vesicle isolation, crosslinking efficiency, and sterility assurance. This review serves as a benchmark for researchers and engineers aiming to bridge the gap between laboratory-scale fabrication and industrial production of nanovesicle-hybridized hydrogels.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4472-0
Dynamic electrocardiography (ECG) monitoring during physical activity remains compromised by motion artifacts that corrupt signal fidelity, particularly with conventional gel electrodes whose impedance rises sharply under deformation. This work presents a thumb-sized liquid metal system integrating gallium-based epidermal electrodes with a self-adhesive elastomeric matrix to sustain robust ECG acquisition against motion. The electrodes exploit the fluidic compliance of eutectic gallium–indium to maintain continuous skin contact, while the adhesive formulation ensures stable interfacial coupling without additional fixation. The system achieves low motion artifact levels, preserving waveform morphology and R-peak detectability during ambulation. The compact form factor enables unobtrusive wearability, and the materials architecture addresses the trade-off between adhesion and conformability that limits existing dry electrodes. The study establishes a materials and device pathway for clinical-grade dynamic ECG in ambulatory and point-of-care settings, with implications for continuous cardiac monitoring where patient movement is unavoidable.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4433-5
Negative thermal expansion (NTE) and zero thermal expansion (ZTE) materials are technologically relevant for precision engineering, yet their practical deployment is constrained by narrow operating temperature windows. This study introduces an entropy-designing strategy to regulate the thermal expansion behavior in the AⅠBⅡCⅢMo3O12 system, specifically K0.4(Mg0.25Mn0.25Co0.25Ni0.25)0.4Sc1.6Mo3O12 (CE0.4MO) and related CExMO compositions (x = 0.4, 0.6, 0.8, 1.0). By tuning configurational entropy, the operating temperature windows for both NTE and ZTE are significantly broadened, with the ZTE region shifting to higher temperatures. Among single-phase compositions, CE0.4MO exhibits the lowest configurational entropy and demonstrates NTE from 100 to 830 K and ZTE up to 1100 K, surpassing most reported ZTE materials. Systematic analyses of structural evolution, lattice dynamics, and electronic structure reveal that reduced configurational entropy suppresses structural evolution, directly correlating with decreased structural flexibility. Higher atomic displacement parameters (ADPs) of oxygen in CE1.0MO provide experimental evidence for enhanced flexibility. Raman spectroscopy shows that the full width at half maximum (FWHM) of peaks in the 750–900 cm-1 range positively correlates with configurational entropy, indicating reduced lattice disorder, while modes within 750–1050 cm-1 blue-shift as entropy decreases, confirming lattice stiffening. Electron localization function (ELF) and charge density analyses indicate that Mg/Mn/Co/Ni/Sc–O bonds are ionic, with ionicity weakening as configurational entropy decreases, thereby enhancing constraints on atomic vibrations and reducing structural flexibility. This work establishes a theoretical foundation for designing thermal expansion materials with wide operating temperature ranges.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4467-x
Conventional eye-movement interaction systems depend on video capture, infrared tracking, and image recognition, which impose inherent constraints on accuracy, response latency, and stability. This study introduces an eyelash-guided signal interaction system based on a triboelectric nanogenerator (PF-TENG) using PDMS-FDTS thin films. The system employs eyelash movements as interactive inputs, eliminating the need for complex optical acquisition devices. A CNN-LSTM hybrid neural network classifies distinct eyelash movement patterns with a classification accuracy exceeding 98.5%. The PF-TENG device exhibits ultra-flexibility and transparency, enabling seamless integration onto eyeglasses without obstructing the user's field of view. Experimental validation demonstrates real-time monitoring of ocular states for driving fatigue detection, accurately identifying fatigue signs and enhancing application potential in intelligent driving. The system offers a natural, comfortable input modality and significant advantages for human-machine interaction, with broad prospects in eye-movement control and intelligent transportation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4343-7
Piezoelectric materials interconvert mechanical and electrical energy, but piezoceramics are brittle while PVDF-based ferroelectric polymers exhibit low piezoelectric coefficients (d33 ≈ -30 pC N-1). Chemical modification via morphotropic phase boundary (MPB) engineering has raised d33 in P(VDF-TrFE) to -63.5 pC N-1, and to -69 pC N-1 with stretching, but intrinsic piezoelectricity in relaxor terpolymers remains limited. Here, relaxor ferroelectric P(VDF-TrFE-CFE) with varying C=C double bond (DB) content is synthesized via dehydrochlorination. Structural and electrical characterization reveals that increasing DB content stabilizes long-range ferroelectric order while suppressing short-range relaxor characteristics, forming a trans/helix phase boundary. At a critical DB content of 2.0 mol%, a markedly enhanced intrinsic d33 of -129.0 pC N-1 is achieved, outperforming previous MPB approaches. This finding addresses the fundamental bottleneck of low piezoelectric response in flexible ferroelectric polymers and provides a viable route for high-performance wearable electromechanical devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4377-9
Continuous molecular monitoring on dynamic biological tissues demands electrochemical interfaces that maintain charge transport and reactivity under large mechanical strain. Existing stretchable platforms based on conductive elastomer composites or serpentine metal interconnects suffer from strain-induced disruption of percolation networks, active area fluctuation, and interfacial charge-transfer kinetic degradation, producing baseline drift and signal distortion that preclude reliable operation on skin, stomach, or intestine. Xu et al. (Science, 2026, 392) introduced SIRES, an intrinsically stretchable electrochemical interface that couples a strain-resilient liquid-metal elastomeric architecture with a Randles-circuit-informed design strategy. The platform preserves stable charge transport and electrochemical reactivity during large deformation, enabling high-fidelity multiplexed molecular sensing across diverse dynamic biological surfaces. This highlight analyzes the material-circuit co-design framework, evaluates its performance limits against conventional stretchable electrodes, and identifies remaining barriers in fabrication scalability, encapsulation reliability, and system-level integration. The work establishes a universal design paradigm for soft bioelectronics, with direct implications for wearable and implantable diagnostic translation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4249-2
Underwater bubble manipulation is critical for water electrolysis, heat transfer, and mineral flotation, yet existing strategies relying on buoyancy or Laplace gradient forces from asymmetric surface geometries suffer from limited flexibility and narrow applicability. This work introduces a temperature-responsive anisotropic cilia surface (TRAS) that achieves bidirectional long-range bubble transport by modulating elastic modulus and stiffness. The TRAS enables precise control over the asymmetric three-phase contact line and viscous resistance, facilitating reversible bubble motion. Experimental validation using aqueous ethanol droplets with varying surface tensions (73.16 mN/m for 0 vol% to 22.27 mN/m for 100 vol%) on cilia with center-to-center spacings of 0.2–1.0 mm reveals that transport direction depends on both cilia spacing and liquid surface tension. Droplets of 0 vol% and 20 vol% ethanol exhibit sustained reverse transport on hard cilia, while 60 vol%, 80 vol%, and 100 vol% solutions show sustained forward transport. Notably, 40 vol% ethanol droplets display bidirectional transport at 0.6 mm spacing, reverse transport at 0.8 and 1.0 mm, and forward transport at 0.2 and 0.4 mm. These results demonstrate that tuning surface tension and cilia spacing provides a versatile platform for directional bubble manipulation, with promising applications in heat transfer, electrochemistry, and gas handling systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4418-7
Glioblastoma (GBM) remains the most lethal primary brain tumor, with the blood-brain barrier (BBB) severely restricting effective treatment options. Immunotherapy has achieved remarkable success in cancers such as lung cancer and melanoma, yet its efficacy in GBM is constrained by the immunosuppressive tumor microenvironment and a paucity of tumor-infiltrating T cells. This study developed a biomimetic nanocomposite for the co-delivery of an immunogenic cell death (ICD) inducer and an indoleamine 2,3-dioxygenase 1 (IDO-1) inhibitor to overcome these challenges. Paclitaxel-derived carbon dots (PCDs), which induce ICD in tumor cells and promote the recruitment and activation of immune cells, were synthesized and assembled with Indoximod (an IDO-1 inhibitor) to form a nanocomposite (P-In). A biomimetic coating was subsequently applied to create M@P-In. This coating significantly enhanced BBB penetration and tumor cell uptake. The M@P-In nanocomposite efficiently induced ICD in tumor cells and inhibited IDO-1 activity via the released Indoximod, thereby reversing T-cell suppression and activating antitumor immune responses. Consequently, M@P-In demonstrated potent antitumor efficacy against glioblastoma in vivo with minimal systemic toxicity. This work presents a novel and promising strategy for immunochemotherapy against GBM by co-delivering a carbon dot-based ICD inducer and an IDO-1 inhibitor to the tumor site.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4428-0
Passive radiative thermal management is reframed as a device-level engineering problem for thermoelectric generators (TEGs) rather than a spectral-material optimization exercise. The surface temperature difference (ΔT) generated by photothermal (PT) absorbers and passive daytime radiative cooling (PDRC) emitters is not equivalent to the effective junction ΔT that drives carrier transport under load; parasitic heat leakage, contact thermal/electrical resistance at electrodes and interfaces, and nonuniform heat spreading systematically degrade the usable gradient. Spectral selectivity sets the upper bound of attainable ΔT, while module architecture, interfacial resistance, and heat-transfer path matching determine whether that bound is preserved as continuous electrical output. The Perspective identifies a critical metrology gap: most reports cite surface ΔT or peak open-circuit voltage without reporting the ΔT-transfer ratio under load, obscuring where thermal losses occur. Because both open-circuit voltage and internal electrical resistance vary with ΔT, external load must be dynamically matched across day-night and weather cycles; night-time reversal of heat-flow direction through the PDRC/PT stack necessitates DC polarity-conversion circuitry, and compact energy storage must buffer intermittent output. The authors argue that fill-factor reduction can preserve junction ΔT by raising thermal resistance but simultaneously increases electrical resistance and suppresses current. Credible assessment criteria are proposed: outdoor 24 h energy density, load-matched power, day-night continuity, and cycle-to-cycle repeatability, rather than peak voltage alone. Near-term deployment targets building-envelope sensors, structural-health monitors, wearables, and distributed IoT nodes where wiring or battery replacement dominates lifetime cost.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4499-9
Two-dimensional (2D) ferroelectric materials have emerged as promising candidates for next-generation non-volatile memory and neuromorphic computing, yet their integration into commercial devices faces substantial hurdles. This review critically examines the structure, properties, and applications of ferroelectric 2D In-Se materials, with a focus on their potential to overcome the scaling and retention limitations of conventional ferroelectrics such as Hf0.5Zr0.5O2 (HZO). The manuscript synthesizes recent advances in In-Se ferroelectricity, including the mechanisms of polarization switching, modulation strategies, and device demonstrations. Key experimental benchmarks from the literature are analyzed, such as the high data retention and read endurance of 5-nm HZO ferroelectric FETs (IEEE Electron Device Lett, 2019, 40(3): 399-402) and the giant barrier height modulation in ferroelectric van der Waals heterojunctions (Nat Electron, 2020, 3: 466-472). The review also highlights the performance of sliding ferroelectric memories based on rhombohedral-stacked bilayer MoS2, which achieved non-volatile storage with low power consumption (Nat Commun, 2024, 15: 10796). Despite these advances, critical challenges remain: the scalability of In-Se synthesis, the control of domain dynamics at the nanoscale, and the cost parity with silicon-based technologies. By consolidating empirical data and identifying unresolved bottlenecks, this review provides a roadmap for researchers and engineers aiming to translate 2D ferroelectric In-Se from laboratory curiosities to manufacturable devices. The analysis underscores the need for standardized metrology and accelerated lifetime testing to validate industrial viability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4452-8
Europium(III) complexes offer intrinsically narrow red emission (full-width at half-maximum < 5 nm) that is highly desirable for ultrahigh-definition displays, yet their electroluminescence performance is severely limited by unbalanced charge transport and inefficient energy transfer. This work reports a molecular design strategy that modulates both energy transfer and charge transport in Eu³⁺ OLEDs. The synthesized complex, Cz-Eu, incorporates a carbazole-functionalized ancillary ligand to facilitate host–guest energy transfer and hole transport. The single-crystal structure was deposited (CIF: Cz-Eu-cif.cif) and subjected to PLATON validation, which flagged 3 type-1 alerts (CIF construction/syntax errors), 8 type-2 alerts (possible structural model deficiencies), 12 type-3 alerts (low structure quality), and 4 type-4 alerts (improvement suggestions), with no duplication detected. These crystallographic alerts indicate that the reported structure requires further refinement before it can be considered reliable. Nevertheless, the device metrics demonstrate a promising route: the optimized OLED achieves efficient ultranarrow-band red emission, with the potential for high color purity and reduced power consumption. The findings underscore the critical role of ligand engineering in balancing charge fluxes and fostering efficient energy transfer, providing a viable pathway for next-generation red emitters. However, the structural ambiguities highlighted by the PLATON analysis warrant cautious interpretation of the structure–property relationships and suggest that additional crystallographic and device stability studies are necessary to substantiate the claimed performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4358-y
Oxygen electrocatalysis underpins the viability of proton-exchange-membrane water electrolyzers and rechargeable Zn–air batteries, yet commercial deployment remains constrained by the sluggish kinetics of the oxygen evolution reaction (OER) and oxygen reduction reaction (ORR), which impose overpotentials exceeding 300 mV and accelerate catalyst degradation. This review, submitted to SCIENCE CHINA Materials (Manuscript ID SCMs-2026-1384.R1), synthesizes recent advances in rational catalyst design guided by the direct observation and theoretical treatment of reaction intermediates. The authors compile evidence from in situ characterization and computational modeling to establish that intermediate binding energies—particularly *OOH, *O, and *OH on Ru, Ir, Co, and Fe–N–C active sites—serve as predictive descriptors for activity and stability. Cited works demonstrate that 4f-modified Ru–O polarity, spin-balanced Janus Ir–Co magnetic atoms, and aligned d-orbital energy levels in dual-atom sites can shift rate-determining steps and lower activation barriers. The review further examines interfacial microenvironment engineering via anion adsorption, ligand functionalization, and S,N co-doped carbon confinement, which modulate local pH, water orientation, and mass transport. Emphasis is placed on dual-site mechanisms, including FeN6–CoN4 and Co-substituted Ni coordination polymers, where synergistic strong–weak adsorption coupling alters ORR pathways from adsorbate evolution to dissociation. The manuscript provides a critical assessment of descriptor reliability, noting that intermediate binding alone cannot capture dynamic reconstruction, electrolyte effects, or long-term operational stability. By integrating in situ spectroscopy with descriptor-based design, the review offers a framework for translating mechanistic insight into durable, cost-effective oxygen electrocatalysts for industrial electrolysis and metal–air batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4441-7
Early detection of kidney injury remains difficult because routine clinical indicators often lag behind tissue damage. Here we report uNP-CH1055, an ultrasmall renal-clearable NIR-II fluorescent nanoprobe for non-invasive imaging of kidney injury in vivo. uNP-CH1055 formed stable nanoparticles with a hydrodynamic diameter of 3.3 nm, showed good photostability, enabled low-background imaging under a 1200 nm long-pass filter, and underwent rapid renal clearance after intravenous administration. It also exhibited favorable biocompatibility in both cellular and animal studies. In three mechanistically distinct models of renal injury, cisplatin-induced acute kidney injury, ischemia–reperfusion injury and unilateral ureteral obstruction, renal fluorescence increased with injury severity and closely paralleled biochemical and histological indicators, including blood urea nitrogen, serum creatinine, KIM-1 and TUNEL-based readouts. These results identify uNP-CH1055 as a renal-clearable NIR-II probe for early and quantitative assessment of kidney injury across different pathological settings.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4383-8
Conventional cancer therapies remain constrained by undruggable oncogenic proteins and acquired resistance. Proteolysis targeting chimeras (PROTACs) have emerged as a transformative modality that harnesses the ubiquitin-proteasome system to selectively degrade target proteins, offering advantages over traditional small-molecule inhibitors. However, clinical translation of PROTACs is impeded by intrinsic physicochemical limitations: high molecular weight, poor bioavailability, and lack of tumor-specific delivery. Integrating PROTACs with nanotechnology has yielded advanced nano-PROTACs platforms. Nanocarriers enhance solubility and stability, optimize pharmacokinetics, and enable spatiotemporally controlled drug release through passive or active targeting. This review systematically summarizes recent advances in engineering multifunctional nano-PROTACs for cancer therapy, with particular emphasis on design strategies by which nanoengineering enhances PROTAC performance. We evaluate how these platforms improve anticancer efficacy and minimize systemic toxicity while exploring their therapeutic potential in monotherapy and synergistic treatment settings. Finally, we discuss current challenges and future perspectives, providing a theoretical and technical foundation for next-generation nano-PROTACs as a precise and potent strategy in precision oncology.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4412-y
GeTe-based thermoelectric materials are promising lead-free alternatives to PbTe, but their intrinsically high Ge vacancy concentration (~10^21 cm^-3) leads to excessive carrier density and degraded Seebeck coefficient. This study integrates resonant levels (RLs) via In doping and local van der Waals gaps via Sb/Bi alloying to decouple electron and phonon transport. The optimal composition Ge0.91Sb0.04Bi0.04In0.01Te exhibits a Seebeck coefficient of ~287.31 μV K^-1 at 323 K, more than double that of the In-free sample (~102.28 μV K^-1). The peak figure of merit zT reaches ~1.8 at 723 K, with an average zT of ~1.0 over 323–723 K. Vickers hardness is enhanced to ~224 HV, a ~93% improvement over pristine GeTe (~116 HV). X-ray diffraction reveals a structural evolution toward a pseudo-cubic phase with increasing In content, and the (202) peak shifts to lower angles, indicating lattice expansion. These results demonstrate that synergistic RLs and van der Waals gaps effectively optimize carrier concentration and suppress thermal conductivity, offering a viable route for high-performance, mechanically robust GeTe thermoelectrics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4457-y
The relentless scaling of wireless communication toward millimeter-wave (mmWave) and sixth-generation (6G) systems has exposed fundamental limitations in conventional radio-frequency (RF) switches based on field-effect transistors, p-i-n diodes, and microelectromechanical systems, which suffer from trade-offs among insertion loss, isolation, footprint, power consumption, actuation voltage, and integration complexity. Non-volatile memristive switches have emerged as attractive alternatives because their resistance states can be electrically programmed and retained without continuous power consumption. However, integrating such emerging switches into functional mmWave integrated circuits remains a major challenge. Pazos et al. reported a major step by co-integrating two-dimensional hexagonal boron nitride (hBN) memristive RF switches with a commercial gallium nitride (GaN) high-electron-mobility transistor (HEMT) monolithic microwave integrated circuit (MMIC) platform. Au/hBN/Au memristors were introduced directly into the back-end-of-line (BEOL) while preserving the underlying GaN HEMTs and passive microwave circuitry. The active switching area is approximately 2 μm × 2 μm. The devices exhibited a pristine capacitance of approximately 24.5 fF and leakage currents below 100 fA at 4 V, with low-resistance states of only a few ohms after switching. Cross-sectional transmission electron microscopy revealed a well-defined ~8-nm layered hBN structure before electrical stressing, and a filament-like pathway accompanied by Au penetration after switching to the low-resistance state. The work demonstrates competitive wideband switching performance, high-temperature non-volatility, transistor-assisted programming, continuous RF attenuation, selective signal routing, and frequency-reconfigurable resonators, establishing a new integration paradigm for programmable mmWave electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4498-7
Two-dimensional porphyrin-based hypercrosslinked polymers (TPP-HCPs) were synthesized via room-temperature interfacial polymerization using 5,10,15,20-tetraphenylporphyrin and 1,3,5-trioxane. The resulting TPP-HCPs exhibited a BET surface area of 548 m2 g-1 and a CO2 uptake of 7.97 wt% at 1 bar and 298 K. CuO/TPP-HCPs nanospheres were fabricated by thermal conversion of Cu(NO3)2·3H2O in DMF at 135 °C, using TPP-HCPs as dynamic templates. This in-situ strategy generated CuO nanoparticles within the conjugated porous matrix, facilitating electron transfer and enhancing CO2 access to catalytic centers. In CO2 electroreduction, the composite achieved a total gas Faradaic efficiency exceeding 90% at ~500 mA cm-2 (-1.4 V vs. RHE), with 40.9% for C2H4, 8.2% for CH4, 31.9% for CO, and 12.3% for H2. The catalyst maintained stability over 24 h in an H-cell. These results demonstrate that 2D conjugated polymer-templated catalysts can sustain high-rate CO2 conversion to value-added products, offering a viable route for industrial CO2 utilization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4405-9
Conventional metal-halide X-ray scintillators, including Bi4Ge3O12 (BGO), Cs(Na)I:Tl, and Lu1.8Y0.2SiO5:Ce (LYSO), suffer from hygroscopic decomposition, high-temperature fabrication, and mechanical rigidity, which restrict their deployment in harsh-environment radiography. This study reports a nontoxic zero-dimensional organic–inorganic hybrid copper(I) halide, Cu2I2(C26H36NP)2 (Compound G), synthesized via a room-temperature solution route. The bulky phosphine ligands confer exceptional superhydrophobicity, with the material retaining 91.95% of its initial luminescence after 30 days of water immersion. A flexible scintillator screen fabricated from styrene-ethylene-butene-styrene (SEBS) exhibits a light yield of ~32,500 photons MeV-1, a spatial resolution of 19.14 lp mm-1, and a detection limit of 0.8 μGyair s-1. The screen enables stable X-ray imaging under flexible, high-temperature, and underwater conditions, eliminating vignetting and distortion in nonplanar objects. These metrics demonstrate that the superhydrophobic copper(I) halide scintillator addresses the water-stability bottleneck of commercial scintillators while delivering competitive light output and resolution, offering a viable pathway for medical diagnosis, nondestructive inspection, security checking, and space exploration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4432-9
Sodium vanadium phosphate (Na3V2(PO4)3, NVP) with NASICON structure is a promising cathode for sodium-ion batteries but suffers from low electronic conductivity and a high energy barrier for the V4+/V5+ redox couple, limiting practical energy density. A medium-entropy tuning strategy yields the multi-element substituted Na3.2V1.5Cr0.1Fe0.1Mn0.1Ni0.1Ti0.1(PO4)3 (ME-NVP). Entropy modulation tailors the microscopic electronic structure, enabling reversible V4+/V5+ redox at 4.0 V. Analyses reveal a synergistic diffusion mechanism that accelerates Na+ transport and enhances multiple-electron redox kinetics. Ex-situ X-ray diffraction confirms highly reversible structural evolution during cycling. The ME-NVP cathode delivers 116.8 mAh g-1 at 0.1C and retains 83.9% of initial capacity after 1000 cycles at 20C, with excellent performance from -12 to 50 °C. This work demonstrates that configurational entropy regulation unlocks high-energy polyanion cathodes for advanced sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4448-y
Zero-dimensional (0D) hybrid metal halides are promising for optoelectronic displays, bioimaging, and anti-counterfeiting due to strong exciton localization and self-trapped exciton (STE) emission. However, low-toxicity, biocompatible zinc halides with blue emission remain scarce, hindered by structural isolation of [ZnBr4]2− tetrahedra, electron-phonon coupling, lattice distortion, and nonradiative relaxation. Here, we synthesize MPAZnBr4 (MPA = N-(3-aminopropyl) morpholine), a 0D zinc bromide halide. Single-crystal X-ray diffraction reveals a monoclinic P21/c space group with a = 6.65190 Å, b = 16.11210 Å, c = 13.79640 Å, β = 94.5700°, Z = 4, and a calculated density of 2.394 g/cm3. The isolated [ZnBr4]2− tetrahedra are hydrogen-bonded to MPA cations, with the shortest Br···Br contact of 4.76 Å indicating weak inter-cluster electronic coupling. Upon photoexcitation, MPAZnBr4 exhibits bright blue emission centered at 450 nm with a full width at half maximum of 135 nm. Wavelength-dependent emission mapping confirms a single radiative pathway, while temperature-dependent photoluminescence identifies triplet STE emission with a thermal quenching activation energy of 55 meV. The extensive hydrogen-bonding network imparts remarkable structural stability, showing negligible photoluminescence decay under prolonged excitation or storage. As a proof-of-concept, we demonstrate switchable and rewritable information encryption and decryption, enabling complex luminescent patterns. These findings provide a strategy for constructing highly stable, low-toxicity blue-emissive Zn-based 0D metal halides for advanced photonic and information-security applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4476-1
Self-sustained oscillation in soft actuators enables autonomous, untethered robotic locomotion, yet existing light-driven systems suffer from low oscillation frequencies, rapid photothermal degradation, and reliance on external controllers. This work presents a bat-inspired soft robot that converts continuous near-infrared (NIR) irradiation into sustained rotational motion via a coiled MXene-based liquid crystal elastomer (LCE) actuator. The actuator integrates Ti3C2Tx MXene nanosheets as photothermal converters within an LCE matrix, achieving a photothermal conversion efficiency of 78.3% and a steady-state temperature of 142 °C under 1.5 W cm−2 NIR (808 nm). The coil geometry induces a self-shadowing effect that generates periodic light exposure, producing autonomous oscillation at 2.7 Hz with an amplitude of 45°. The robot demonstrates a rotational speed of 120 rpm and a specific power density of 3.2 W kg−1, outperforming previously reported light-driven oscillators by a factor of 2.5. Under continuous operation for 10,000 cycles, the actuator retains 92% of its initial oscillation amplitude, with a degradation rate of 0.008% per cycle. The bat-inspired wing morphology enables directional rotation and obstacle avoidance in confined spaces. This platform eliminates the need for external modulation, offering a scalable route to autonomous soft robotics for inspection, environmental monitoring, and micro-manipulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4391-5
Self-assembled monolayers (SAMs) enable precise tuning of the ITO/active layer interfacial dipole, yet their impact on the crystallization kinetics of the overlying active layer remains poorly understood, limiting their potential in high-efficiency organic solar cells. This study introduces THPC, a self-assembling material with an extended carbazole core and heteroatom substitution, as a hole transport layer (HTL). Unlike the hydrophilic PEDOT:PSS, THPC exhibits low surface energy, providing a favorable template that extends the film formation kinetics of the PM6:L8-BO-X blend by nearly 1.4 times, mitigating the explosive nucleation prevalent in PM6-based active layers. This promotes a highly ordered fibrous morphology and enhances vertical phase separation. The deep work function of THPC (5.32 eV) increases the built-in potential, reduces interfacial trap density, and facilitates charge extraction. Consequently, non-radiative recombination loss decreases from 0.243 eV to 0.227 eV, and the open-circuit voltage rises from 0.866 V to 0.883 V, yielding a power conversion efficiency (PCE) of 20.19%, outperforming the PEDOT:PSS control (18.67%). This finding is confirmed across multiple Y-series acceptors, all approaching 20% PCE. Notably, the D18:L8-BO system achieves a PCE of 20.55%, demonstrating broad applicability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4321-x
Poly(ethylene oxide) (PEO)-based solid polymer electrolytes are leading candidates for solid-state lithium metal batteries due to their flexibility, processability, and interfacial compliance. However, the strong crystallization tendency of PEO and limited lithium salt dissociation result in low ionic conductivity and low Li+ transference number, exacerbating concentration polarization and interfacial instability. Introducing metal-organic framework (MOF) fillers into PEO matrices has emerged as an effective route to regulate polymer-chain packing and promote salt dissociation via Lewis acid-base interactions. Yet, most studies focus on cubic ZIF-8, whose saturated Zn coordination environment limits intrinsic Lewis acidity and restricts its ability to immobilize TFSI- anions. Simultaneously, simple physical blending often leaves discontinuous interfacial transport regions in composite electrolytes, so improved salt dissociation does not automatically translate into fast Li+ transport. Here we report a PEO-based composite polymer electrolyte, denoted as PZS, that couples monoclinic ZIF-8 (M-ZIF-8) nanosheets with a thin SiO2 layer. The design combines two complementary functions: the under-coordinated Zn sites in M-ZIF-8 provide strong Lewis acid centers to adsorb TFSI- and promote LiTFSI dissociation, while the hydroxyl-rich SiO2 shell improves compatibility with the PEO matrix and helps construct continuous interfacial Li+ transport pathways. Benefiting from this synergy, the optimized PZS electrolyte delivers an ionic conductivity of 8.3 × 10-4 S cm-1 and a Li+ transference number of 0.57 at 60 ℃, together with an electrochemical stability window of 5.2 V. Li||Li symmetric cells remain stable for over 1200 h at 0.1 mA cm-2, and LFP||Li full cells retain 80% of their capacity after 400 cycles at 0.5 C.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4347-9
Overcoming the intrinsic loading ceiling of oxide-supported single-atom catalysts remains a long-standing challenge, because oxide frameworks generally provide limited capacity for accommodating high densities of isolated metal species. Here, we report a hollow TiO2 nanoreactor that effectively addresses the long-standing loading limitation of oxide-supported catalysts by coupling high-capacity ion exchange with structural confinement. The multiscale framework is derived from a sodium titanate hollow flower-sphere assembled from ultrathin nanosheets. It enables broad accessibility of exchange sites and facilitates high Cu uptake prior to oxide formation. Subsequently, during Ar-assisted transformation into oxygen-vacancy-rich TiO2, the incorporated Cu species remain highly dispersed within the framework, while vacancy-mediated metal–support interactions further enhance their stability. As a result, controllable Cu speciation is achieved at ultrahigh loadings of 7.4 wt% as spatially isolated single atoms and 12.4 wt% as single-atom/subnanometer-cluster hybrids. The optimized hybrid catalyst delivers a hydrogen evolution rate of 28.8 mmol g−1 h−1 under simulated sunlight, surpassing conventional low-loading Cu/TiO2 systems under comparable conditions. This strategy is readily extendable to other transition metals (Fe, Co, and Ni), establishing a structural design principle for constructing high-density and speciation-controlled metal sites on oxide supports.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4351-8
Breaking intrinsic structural symmetry is a fundamental prerequisite for pronounced nonlinear optical responses. Low-symmetry semiconductors with inherent anisotropy enable self-powered optoelectronic conversion and polarization-sensitive functionalities. This work reports the synthesis of low-dimensional van der Waals chain TeSe2 crystals with intrinsic inversion and C3 symmetry breaking. Angle-resolved polarized Raman spectroscopy and second-harmonic generation measurements confirm crystalline anisotropy and nonlinear optical performance. Electrical transport studies reveal p-type conduction with a room-temperature field-effect mobility of 122 cm2 V-1 s-1. The TeSe2 photodetector achieves self-powered detection and linearly polarized light detection across 405–1064 nm, with a photoresponsivity of 77.3 mA/W at 532 nm. The linear photogalvanic effect response is effectively modulated by gate voltage. Density functional theory calculations attribute p-type doping to Te and Se vacancies, while the nonlinear optical origin is linked to strong Berry curvature. Applications in polarization encoding communication and polarization imaging are demonstrated, indicating potential for low-energy-consuming, highly sensitive, on-chip integrated linear polarized photodetectors.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4420-7
Cu2-xSe is a leading p-type thermoelectric material owing to its phonon-liquid electron-crystal (PLEC) behavior, yet the atomic-scale mechanisms governing Cu+ migration remain unresolved. This study employs in situ high-resolution neutron diffraction coupled with maximum entropy method (MEM) analysis to map the temperature-dependent evolution of Cu+ nuclear density in β-Cu2Se and β-Cu1.95Se. At 398–423 K, intra-tetrahedral Cu 8c ↔ 32f <111> hopping emerges, with isosurface values of 0.505 fm Å-3 for β-Cu2Se and 0.484 fm Å-3 for β-Cu1.95Se. Above 448 K, inter-tetrahedral pathways form via Cu 32f ↔ 32f <100> or 32f ↔ 4b ↔ 32f <111> migration, as revealed by line scans along [1̅11̅] up to 723 K. The presence of Cu vacancies (x = 0.05) alters the onset and connectivity of these pathways, directly impacting phonon scattering and electron transport. These findings establish a structural basis for controlling Cu+ mobility, offering a rational route to mitigate Cu precipitation and enhance zT stability beyond 1.5 at 900 K. The work bridges microstructural dynamics and thermoelectric performance, providing critical guidance for defect engineering in superionic thermoelectrics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4425-4
Flexible and weavable alternating-current electroluminescent (ACEL) fiber devices are pivotal for wearable displays and human-computer interfaces, yet their intrinsic lack of color tunability restricts high-density information interaction. This study presents a dynamically color-tunable electroluminescent fiber device with a coaxial winding structure that integrates multiple fiber electrodes emitting the three primary colors. Through simple voltage driving, the device achieves a color gamut covering 131.07% of the sRGB standard, enabling arbitrary full-color tunability, including standard white light with CIE coordinates of (0.31, 0.33). The emission peak is continuously tunable over a 161.7 nm range, a 4-fold enhancement compared to previously reported ACEL fibers. The coaxial winding architecture is compatible with large-scale fabrication, yielding hundred-meter-scale fiber devices with a luminance variation of only 2.76%. The electroluminescent performance remains stable under stringent industrial standards: 10,000 friction cycles, 20 accelerated washing cycles, and 10-day storage at 105 °C and −20 °C. Integration into a smart textile watchband demonstrates real-time heart rate visualization via progress color changes and gesture-controlled color switching, validating its potential as an effective human-computer interface.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4497-y
Proton exchange membrane water electrolysis (PEMWE) enables green hydrogen production from renewable electricity but relies on scarce Ir/Ru catalysts for the kinetically sluggish and acid-stable oxygen evolution reaction (OER). Non-noble-metal oxides typically suffer rapid dissolution and structural collapse under acidic, high-current conditions. Conventional cubic spinel Co3O4 (C-Co3O4) contains both inactive tetrahedral Co and active octahedral Co sites; tetrahedral dissolution destabilizes the framework. A recently reported trigonal Co3O4 phase (Tri-Co3O4), synthesized via vacuum-mediated molten-alkali mechanochemical methods, consists entirely of edge-shared [CoO6] octahedra in a compact two-dimensional layered structure. This configuration eliminates tetrahedral sites and exposes abundant octahedral active centers. Structural characterization by X-ray diffraction confirms strong (0001) and (0002) reflections, while Co K-edge EXAFS shows only Co-Cooct coordination without Co-Cotet signals. Tri-Co3O4 achieves 10 mA cm-2 at an overpotential of 269 mV, 181 mV lower than C-Co3O4 (450 mV), with low cobalt dissolution and 2500 h operation at 1.7 V in a practical PEMWE device. In situ XAFS reveals minimal Co oxidation-state change and nearly unchanged Co-O coordination during OER, confirming octahedral framework stability. DFT calculations identify the Tri-Co3O4 (10-10) facet as closest to the volcano apex, with balanced *OH and *O adsorption favoring the adsorbate evolution mechanism. Stability arises from coupled coordination, dimensional, and valence effects: outer-layer Co3+ provides high activity, middle-layer Co2+ stabilizes the lattice, and weak out-of-plane van der Waals interactions increase the energy barrier for Co removal. This highlight critically evaluates the mechanistic origins, unresolved questions regarding metastable phase generality, synthesis scalability, and long-term structural evolution under PEMWE operation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4480-1
Ternary organic solar cells (OSCs) incorporating a structurally compatible guest acceptor (C7-Cl) into the PM6:BTP-eC9 host system are demonstrated. The low Flory-Huggins interaction parameter between host and guest acceptors facilitates intimate mixing, optimizing molecular packing and energy-level alignment. High-sensitivity sEQE and EQEEL analyses reveal a reduced non-radiative energy loss (KE3) of 0.216 eV in the ternary device. Consequently, the optimized ternary OSC achieves a champion power conversion efficiency (PCE) of 20.02% and an improved T80 operational lifetime of 1065 h. This work establishes a feasible strategy via structurally compatible guest doping to simultaneously optimize vertical phase separation and suppress non-radiative loss, providing a facile and effective route toward high-performance and stable OSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4494-9
Superionic conductors exhibit high cation mobility arising from weak binding and continuous transport pathways, atomistically characterized by extensive structural disorder and partial occupancy akin to amorphization. This disorder, whether confined to a cation sublattice or extended to full amorphization, strongly impedes lattice thermal transport, rendering these materials intrinsically ideal thermal insulators. This work investigates Ag26I18W4O16, a superionic conductor tunable from fully amorphous to single-crystalline states, as a model system to probe the impact of disorder and amorphization on thermal transport. Extensive Ag+ disorder, in both crystalline and amorphous phases, reduces thermal conductivity to approximately the theoretical lower bound of 0.16 W/m-K with virtually no temperature dependence, while concurrently achieving the lowest mean sound velocity ever recorded for a dense solid. Pair distribution function (PDF) analysis of synchrotron X-ray total scattering data indicates that short-range disorder (< 5 Å), rather than long-range periodicity, governs thermal insulation performance in both phases. These findings suggest a design strategy reconciling structural stability with glass-like thermal insulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4466-3
Conventional surface coating technologies for 45 steel are constrained by high processing temperatures, limited material compatibility, and insufficient interfacial bonding. This study introduces ultrasonic vibration-assisted mechanical coating (UVAMC) as a low-temperature deposition route that mitigates these limitations. The process yields a chromium coating on 45 steel with a nanoscale elemental interdiffusion transition layer at the interface, achieving a bonding strength of 66.0 MPa. The coating delivers improved corrosion resistance in aggressive environments while preserving the substrate's original compressive and tensile strength. The method also demonstrates broad process adaptability, successfully depositing copper, aluminum, and 316 stainless steel powders, and forming complex shapes such as the "SZU" pattern. These results establish UVAMC as a viable surface functionalization strategy for metallic materials, combining efficient deposition with operational flexibility.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4447-3
Chargeable photoconductivity, a non-volatile photoresponse phenomenon, was investigated in multiferroic heterostructures comprising Bi0.85La0.15FeO3 (BLFO) and a quasi-two-dimensional electron gas (Q2DEG). Two device architectures, LSMO/BLFO/Q2DEG and Pt/BLFO/Q2DEG, were fabricated and characterized under varying electrical connection conditions between the top electrode and the Q2DEG during illumination and dark waiting stages. Current-voltage (I-V) measurements reveal that the heterostructures exhibit persistent photoconductivity after illumination, with the magnitude and retention dependent on the circuit configuration. Under open/open conditions, the photocurrent increases with illumination duration, and subsequent dark waiting leads to a gradual decay, indicating charge storage and release mechanisms. The LSMO/BLFO/Q2DEG heterostructure demonstrates superior chargeable photoconductivity compared to the Pt counterpart, attributed to the oxygen vacancy migration and interfacial polarization effects. These findings establish a foundation for oxide-based photoelectric memory devices with potential for low-power, non-volatile optoelectronic applications. The results provide critical insights into the interplay between ferroelectric polarization, oxygen vacancy dynamics, and charge trapping at the BLFO/Q2DEG interface, offering a pathway for designing advanced multiferroic optoelectronic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4311-y
Chronic infections caused by biofilms of drug-resistant bacteria pose a significant challenge in clinical treatment. Traditional NIR-I photothermal therapy has limitations, including restricted tissue penetration and potential damage to normal tissues due to high temperatures. While NIR-II light offers deeper penetration, there remains a scarcity of materials capable of simultaneously responding to both NIR-I and NIR-II wavelengths and integrating multiple sterilization mechanisms under mild conditions. In this study, a Fe-based high-entropy spinel oxide (HEOs) was designed and synthesized. Benefiting from lattice distortion induced by the high-entropy effect and the hybridization of multiple metal d-orbitals, the material achieves cooperative optimization of its electronic band structure. Consequently, it exhibits efficient broad-spectrum photothermal properties across both NIR-I and NIR-II regions alongside excellent peroxidase-like (POD) activity. Under dual-wavelength laser irradiation, the material enables mild yet efficient photothermal conversion (<50 °C) while simultaneously catalyzing hydrogen peroxide (H2O2) to generate abundant hydroxyl radicals (·OH), thereby constructing a synergistic antibacterial system combining dual-window photothermal therapy and enzymatic catalysis. In vitro experiments confirmed that the HEOs possesses potent bactericidal and biofilm eradication capabilities against both Gram-positive and Gram-negative bacteria. In a mouse model of drug-resistant bacterial wound infection, the material, assisted by either NIR-I or NIR-II laser irradiation, effectively cleared the infection, reduced inflammation, and promoted collagen deposition and angiogenesis, thereby significantly accelerating wound healing. This work not only provides a novel strategy for developing dual-window-responsive antibacterial materials for deep-tissue infections but also deepens the understanding of the structure-activity relationship in high-entropy materials at the electronic structure level.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4404-7
Electrochemical propylene epoxidation offers a sustainable route to propylene oxide (PO), but achieving high selectivity and stability under industrial current densities remains challenging. Herein, we report a high entropy amorphous CoFeNiCrMnBOx borate loaded with high valence Pt single atoms catalyst (a-Pt-HEBO) for stable bromine radical-mediated propylene epoxidation reaction (BrPOR). The high-entropy amorphous structure reshapes the interfacial hydrogen-bonding network and enriches free water, substantially lowering the energy barrier for water dissociation. Meanwhile, the strong electronic interactions between the coordinatively unsaturated, high-valence single Pt atoms and the substrate effectively prevent transition metal dissolution at high anodic potentials. The catalyst achieved 82.1% Faraday efficiency of PO at an industrial grade current density of 100 mA cm-2, and demonstrated excellent industrial application stability in up to 500 h of continuous test and within a scaled-up electrolyzer (4 × 4 cm2). This work provides a design for high-entropy catalysts in halogen-mediated electrosynthesis and a viable pathway toward carbon-neutral PO production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4313-7
Liquid-to-vapor mass transfer is central to energy and environmental processes. Conventional distillation relies on vapor-liquid equilibrium and device-level optimization, with materials playing passive structural roles. Non-boiling processes such as membrane distillation and interfacial solar evaporation localize phase change at confined interfaces, making mass transfer a materials-mediated transport phenomenon where interfacial structure and chemistry dictate evaporation kinetics, vapor escape, and solute rejection. Janus interface materials, featuring spatially separated hydrophilic and hydrophobic domains, introduce architectural asymmetry to regulate liquid-to-vapor mass transfer. This review summarizes recent advances, highlighting mechanisms including the cooperative pump-valve effect, nanoconfinement-enhanced transport, and mitigation of fouling and scaling. Representative applications in membrane distillation, solar-driven evaporation, and personal thermal-moisture management are systematically discussed. Key challenges and future opportunities are outlined, particularly in advancing fundamental understanding, scalable fabrication, and practical implementation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4324-4
Magnesium-oxygen (Mg-O2) batteries offer high theoretical energy density and low-cost earth-abundant magnesium, yet practical deployment has been impeded by poor cycling stability and low energy efficiency, primarily due to the sluggish decomposition of conventional MgOx discharge products. Here we demonstrate that trace water in the electrolyte redirects the cathodic reaction to form chemically reactive Mg2(OH)3Cl·4H2O as the main discharge product, enabling a new reversible pathway: 8Mg2+ + 4Cl- + 3O2 + 22H2O ⇋ 4Mg2(OH)3Cl·4H2O. This water-mediated chemistry significantly enhances redox reversibility compared with the MgOx route. The resulting Mg-O2 battery delivers over 324 stable cycles at 1000 mA·g-1 with a capacity of 500 mAh·g-1 and an energy efficiency of 92%, surpassing all previously reported Mg-O2 systems. The electrolyte comprises 0.25 M magnesium bis(trifluoromethanesulfonyl)imide (Mg(TFSI)2) and 0.5 M magnesium chloride (MgCl2) in ethylene glycol dimethyl ether (DME) with a trace amount of water. These findings establish a general strategy for reversible Mg-O2 electrochemistry and provide a new design paradigm for practical magnesium-based energy storage.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4488-x
Thermochromic smart windows based on hydrogels suffer from inevitable freezing at subzero temperatures and dehydration at elevated temperatures, severely limiting their year-round applicability. This study reports a hydrogel-derived liquid (HDL) smart window that circumvents these limitations through a solvent-exchange strategy. The HDL is synthesized by polymerizing a hydroxypropyl cellulose (HPC) and N-isopropylacrylamide (NIPAM) network in a water-glycerol binary solvent, followed by complete removal of the water phase via vacuum-assisted evaporation. The resulting anhydrous liquid exhibits a lower critical solution temperature (LCST) of 32 °C, with a solar modulation ability (ΔTsol) of 63.2% and a luminous transmittance (Tlum) of 88.1% in the clear state. Critically, the HDL remains optically switchable after 1000 hours at -40 °C and 1000 hours at 80 °C, with no observable phase separation or freezing. The smart window prototype demonstrates a 12.3% reduction in indoor cooling energy consumption in a simulated tropical climate and a 9.8% reduction in heating energy in a cold climate, compared to a commercial low-E glass. The liquid-state formulation enables facile large-area fabrication via roll-to-roll processing, with a demonstrated 30 cm × 30 cm prototype retaining 95% of the initial ΔTsol after 500 bending cycles. This work establishes a viable pathway for all-climate energy-efficient building envelopes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4468-6
The proliferation of multispectral detection platforms demands materials that simultaneously satisfy electromagnetic interference (EMI) shielding and infrared (IR) camouflage without compromising radio-frequency (RF) transmission. Conventional MXene films exhibit exceptional EMI shielding (>40 dB) but suffer from high IR emissivity and severe RF reflection, precluding integration with wave-transmitting arrays. This work introduces liquid metal (LM)-modified MXene composite films engineered via structural patterning to decouple optical, IR, and RF responses. The LM phase, dispersed within the MXene interlayer galleries, reduces free-electron density and tailors the dielectric loss, while a periodic array architecture creates impedance-matched windows for RF transmission. The resulting films achieve an EMI shielding effectiveness of 36 dB at 510 µm thickness, with a low IR emissivity of 0.36 and an RF transmittance exceeding 80% in the X-band. The patterning strategy suppresses surface current continuity, mitigating the trade-off between shielding and transmission. These metrics represent a 20% improvement in IR camouflage and a 15% enhancement in RF transparency relative to pristine MXene films. The composite films also demonstrate mechanical flexibility, retaining 95% of initial conductivity after 1,000 bending cycles. This work establishes a scalable route for multispectral-compatible materials critical for next-generation stealth and communication systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4263-3
Monolayer black phosphorus (phosphorene) exhibits a direct bandgap and strong in-plane anisotropy, making it a promising candidate for near-infrared (NIR) optoelectronic devices. However, the precise modulation of its excitonic emission via anisotropic strain remains insufficiently understood, particularly regarding the contrasting strain responses of phosphorene versus transition metal dichalcogenides (TMDs). Here, we combine experimental characterization with tight-binding (TB) modeling to elucidate the strain-dependent bandgap evolution in phosphorene. Using a four-band TB model, we derive the bandgap at the Γ point as E_g^BP = 4t1 + 2t2 + 4t3 + 2t5, with hopping parameters t1 = -1.220 eV, t2 = 3.665 eV, t3 = -0.205 eV, t4 = -0.105 eV, and t5 = -0.055 eV. Under tensile strain along the zigzag (ZZ) direction, the interatomic distance associated with t1 increases, reducing the magnitude of |t1|. Since t1 is negative, the bandgap increases, contrary to the behavior of monolayer MoS2, where tensile strain decreases the bandgap due to positive hopping parameters t11, t22, and t12. This anisotropic strain response enables selective tuning of NIR exciton emission. Our findings provide a quantitative framework for strain engineering in phosphorene-based NIR devices, highlighting the critical role of hopping parameter signs in determining bandgap modulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4177-3
Chirality profoundly influences tumor therapy by regulating key physiological processes, yet the link between chirality and therapeutic properties of atomically precise metal nanoclusters (NCs) remains poorly understood. Atomically precise Au25 NCs protected by chiral cysteine ligands (L-Au25(cys)18, D-Au25(cys)18, and Rac-Au25(cys)18) were constructed and systematically investigated to elucidate the association between chirality and tumor therapeutic performance. Although no significant difference in enzyme-like activity was observed among the three NCs, Rac-Au25(cys)18 exhibited enhanced reactive oxygen species generation under 808 nm laser irradiation, achieving superior phototherapeutic effects in both in vitro and in vivo tumor models. The chiral Au25 NCs induced distinct cell death pathways: L-Au25(cys)18 primarily triggered ferroptosis, D-Au25(cys)18 induced both ferroptosis and apoptosis, and all three NCs activated disulfidptosis. In vivo, tumor inhibition rates for L-Au25, D-Au25, and Rac-Au25 groups were 46.7%, 42.5%, and 68.3%, respectively, with no significant body weight fluctuations and minimal hepatorenal toxicity. Hematological and histopathological analyses confirmed favorable systemic biocompatibility. This work clarifies the correlation between chiral structures and tumor therapeutic performance of gold NCs, providing experimental insights and theoretical support for the design of novel chiral nanomaterials and optimization of precise tumor phototherapeutic strategies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4283-0
Smart windows are critical for building energy conservation, yet existing technologies cannot simultaneously satisfy the diverse requirements of light transmission, thermal insulation, and privacy protection across varying scenarios, such as daytime transparency and nighttime heat retention with opacity. Herein, we report a thermo- and electro-responsive ionogel fabricated via one-step photopolymerization, integrating the electrochromic viologen derivative (Pa-PhV)(TFSI)2 with a thermoresponsive matrix. The (Pa-PhV)(TFSI)2 delivers excellent electrochromic performance, featuring dual-band light modulation, a high coloration efficiency of 433.6 cm2 C-1, and a fast coloration time of 2.52 s. The ionogel exhibits three stable switchable states under thermal and electrical regulation, fulfilling core practical demands for full-spectrum photothermal management. Model house tests verify its excellent seasonal adaptability, with a maximum indoor temperature reduction of up to 15 °C in a simulated summer environment. Furthermore, the ionogel enables dual-encrypted data storage via UCST and voltage triggering. This work broadens the application scope of viologen derivatives and offers a competitive strategy for multifunctional smart windows and encrypted data storage.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4487-1
Direct seawater electrolysis offers a cost-effective route to clean hydrogen, but the competitive chlorine evolution reaction (CER) and electrode corrosion impede practical deployment. A NiIr(OH)6 perovskite hydroxide catalyst was synthesized via one-step co-precipitation. In alkaline seawater, it requires only 330 mV overpotential to reach 100 mA cm-2 and sustains 190 h in multi-current step testing. In situ Raman spectroscopy shows that Ir species promote the formation of active NiOOH phases, accelerating oxygen evolution reaction (OER) kinetics. Density functional theory calculations reveal that Ir doping modulates the electronic structure of Ni and Ir sites, strengthening OH adsorption (-2.09 eV) and suppressing Cl- adsorption (-1.38 eV), thereby enhancing OER selectivity. An overall seawater electrolyzer with NiIr(OH)6 || Pt/C delivers 100 mA cm-2 at 1.63 V and operates stably for over 100 h. This work provides a rational design strategy for high-efficiency, corrosion-resistant electrocatalysts for seawater electrolysis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4275-3
Electrochemical in-situ production of active chlorine (AC) via chlorine evolution reaction (CER) can alleviate hull corrosion and residual chlorine overage, which is a highly reliable disinfectant for sewage and ballast water. Nonetheless, the primarily competitive oxygen evolution reaction and gradual anode passivation hinder its practical application. Herein, we employed the in-situ hydrothermal strategy to synthesize Ru/TiO2-x to realize high activity and selectivity of CER. The robust interaction of Ru sites and TiO2-x achieved via a one-step hydrothermal synthesis strategy, the structural and valence state characterizations confirm that Ti3+ stabilizes Ru solely in the metallic state (Ru0) via structural confinement effects, effectively inhibiting catalyst oxidation. As a result, the Ru/TiO2-x requires only an overpotential of 33 mV to reach 10 mA cm−2, and possess strong catalytic durability, sustaining continuous operation for 100 h with negligible current decay. Further integration with a triboelectric nanogenerators successfully realizes the generation of AC, which demonstrates a >99.9% inactivation efficiency against Escherichia coli in simulated seawater environments, while also effectively degrading ammonia nitrogen and urea contaminants in domestic wastewater.
Nano Research Energy•2026•DOI: 10.26599/NRE.2025.9120181
Solid-state lithium metal batteries (SLMBs) demand quasi-solid polymer electrolytes (QSSPEs) that simultaneously deliver high ionic conductivity, interfacial stability, and oxidative resistance. This study reports a QSSPE membrane (MP46) formulated with MG30:LiTFSI:succinonitrile at a 10:4:6 weight ratio, exhibiting a wide electrochemical window of 5.1 V. Complementary infrared spectroscopy, small-angle X-ray scattering, and electron microscopy reveal a hierarchical ionic conductive network consisting of sphere-like nanostructures embedded within microphase-segregated architectures. This morphology enhances lithium-ion transport while preserving mechanical integrity. The strong interfacial adhesion between MP46 and lithium metal enables stable lithium plating and stripping for over 800 h at 0.2 mA·cm–2, effectively mitigating dendrite formation. When paired with LiFePO4 and LiCoO2 cathodes, MP46 sustains prolonged cycling, retaining 80.1% capacity after 1400 cycles at 2 C and 92.1% after 200 cycles at 4.5 V, respectively. Pouch-type cells further demonstrate mechanical flexibility and operational safety under deformation. These results establish MP46 as a viable candidate for stable high-energy-density SLMBs, offering fundamental insights into the design of next-generation polymer electrolytes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4491-3
Magnetic tunnel junctions (MTJs) with multiferroic tunneling barriers offer a pathway to fully electrically controlled multi-state memory, addressing the high energy costs and scalability limits of magnetically controlled counterparts. In this work, we propose a theoretical design achieving four or ten distinct resistance states via electrical control, with a giant tunneling magnetoresistance (TMR) ratio of 1.1×10^4% (11000%). This value surpasses all previously reported MTJs, including experimental systems such as CoFeB/MgO/CoFeB (TMR 65%, 4 states) and theoretical systems like Ga2O3/MgO/Ga2O3 (TMR 1120%, 2 states). The multiferroic barrier enables simultaneous control of ferroelectric and magnetic order parameters, allowing reversible switching between multiple resistance levels without external magnetic fields. Our first-principles calculations reveal that the high TMR arises from spin-dependent tunneling through the barrier, modulated by the ferroelectric polarization direction and magnetization configuration. The device operates with low write energy and exhibits non-volatile retention, making it suitable for high-density storage and in-memory computing. This work establishes a new benchmark for electrically controlled MTJs and provides a practical route to overcome the limitations of current spintronic memory technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4495-3
Room-temperature phosphorescence (RTP) has attracted substantial interest for applications in smart optoelectronics, yet the development of dynamic RTP systems remains intrinsically challenging. Here, we report an appropriately rigid confinement strategy based on NaCl ionic crystals formed in situ via cation-anion exchange, which simultaneously suppresses non-radiative decay and retains sufficient structural flexibility for external stimulation. In the TPN/NaCl and DPB/NaCl systems, dynamic phosphorescence is realized exclusively upon sequential thermal activation and ultraviolet irradiation. Mechanistic investigations reveal that residual water and triplet oxygen initially quench triplet excitons, and their gradual removal enables a competitive evolution between triplet-triplet annihilation (TTA) and phosphorescence pathways. This work establishes a general design principle for constructing stimulus-responsive dynamic RTP systems and resolves the long-standing conflict between rigidity and responsiveness in organic phosphorescent materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4272-3
Ruthenium (Ru)-based alloys are promising alternatives to commercial Pt/C catalysts for the hydrogen evolution reaction (HER) owing to their low cost and favorable hydrogen adsorption properties. However, the sluggish water dissociation on Ru catalysts remains a major kinetic bottleneck in alkaline solutions. Herein, we report a rare earth (RE) dilute alloy strategy by incorporating a trace amount of cerium (Ce, ~1 at%) into a RuCu alloy to promote interfacial water activation. The oxophilic Ce sites strengthen H2O adsorption and reduce the energy barrier for water dissociation, thereby accelerating the Volmer step during alkaline hydrogen evolution. Consequently, the RuCuCe catalyst delivers 10 mA cm−2 at an overpotential of only 18 mV in 1.0 M KOH and maintains stable operation for over 100 h at 500 mA cm−2 in a membrane electrode assembly. In situ electrochemical impedance spectroscopy and pH-dependent measurements verify the facilitated Volmer process induced by Ce incorporation. Temperature-dependent analysis further shows that the apparent activation energy decreases from 47.4 kJ mol−1 for RuCu to 26.4 kJ mol−1 for RuCuCe, consistent with enhanced water dissociation kinetics. This work establishes RE dilute metal alloys as an effective platform for boosting the intrinsic activity of Ru-based alloy catalysts, in which RE incorporation promotes water dissociation while inducing charge redistribution in the alloy matrix.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4294-4
Room-temperature phosphorescence (RTP) polymer materials are attractive for flexible electronics and information encryption due to their tunability and processability. However, achieving polymeric RTP systems that simultaneously exhibit high thermal sensitivity, reversible multicolor emission, and long phosphorescence lifetime (τPhos) with high quantum yield (ΦPhos) remains challenging. Here, we report an in-situ cross-linked self-assembly strategy that converts flexible polymers into rigid polymer microspheres, yielding long τPhos, high ΦPhos, and thermally and time-dependent tunable RTP. The resulting microspheres (PM0.1-0.01-1) exhibit a maximum τPhos of 1754 ms and ΦPhos of 42.83%, markedly superior to previously reported intrinsic polymer RTP materials. At 77 K, they display ultralong green emission with a lifetime of 6019 ms and visible afterglow lasting up to 99 s. The cross-linked microspheres enable time-dependent, continuously tunable RTP and thermally responsive color switching, while maintaining excellent phosphorescence stability in aqueous and high-temperature environments. This provides a versatile platform for dynamic information encryption, full-color afterglow LEDs, and temperature sensing. The strategy establishes a general design principle for developing multidimensional, controllable, and stable high-performance polymer RTP materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4238-2
Infrared nonlinear optical (IR NLO) materials are critical for laser frequency conversion, yet their performance is often constrained by a trade-off between second harmonic generation (SHG) efficiency and laser-induced damage threshold (LIDT). Here, we report a new ternary diamond-like compound, AlGaS3, which successfully balances these competing demands. AlGaS3 crystallizes in a noncentrosymmetric structure composed of wide HOMO-LUMO gap [AlS4] tetrahedra and NLO-active [GaS4] tetrahedra. The compound exhibits a wide experimental optical band gap of approximately 3.38 eV, which is significantly larger than that of the benchmark AgGaS2 (AGS, ~2.70 eV). This wide band gap contributes to a high laser-induced damage threshold (LIDT) of approximately 6.0 times that of AGS, as determined by powder-based measurements. Notably, AlGaS3 also demonstrates a phase-matching SHG response of approximately 0.5 times that of AGS at a fundamental wavelength of 2.09 μm, with particle size-dependent behavior confirming phase-matchability. The combination of wide band gap, high LIDT, and moderate SHG response positions AlGaS3 as a promising candidate for high-power IR NLO applications. This work provides a viable strategy for designing IR NLO materials with enhanced laser damage resistance by incorporating wide-gap tetrahedral units.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4502-1
Near-infrared-II (NIR-II, 1000-1700 nm) luminescent materials are pivotal for deep-tissue bioimaging and optical communication, yet their performance is often limited by low quantum yields and thermal quenching. Here, we report a thermal-enhanced NIR-II luminescence in Sb3+/Er3+ co-doped Cs3GdCl6 microcrystals synthesized via a modified Bridgman method. Under ultraviolet excitation, the co-doped microcrystals exhibit intense NIR-II emission centered at 1532 nm corresponding to Er3+: 4I13/2 → 4I15/2 transition, with a maximum relative sensitivity of 1.2% K−1 at 303 K. Notably, the integrated NIR-II emission intensity increases by 2.3-fold from 298 K to 373 K, demonstrating anomalous thermal enhancement. This behavior is attributed to the thermally activated energy transfer from Sb3+ sensitizers to Er3+ activators, as confirmed by temperature-dependent photoluminescence spectra and decay kinetics. The energy transfer efficiency reaches 86% at room temperature and further improves with rising temperature. The microcrystals also show excellent photostability, retaining 95% of initial intensity after 120 min continuous UV irradiation. Furthermore, we demonstrate a proof-of-concept wireless optical communication link using the microcrystals as a NIR-II phosphor, achieving a signal-to-noise ratio of 30 dB at 400 Hz modulation frequency. These findings provide a new strategy for designing thermal-enhanced NIR-II luminescent materials and expand their potential in temperature sensing and optical communication.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4299-9
A dual-doping strategy incorporating boron (B) and sulfur (S) into graphitic carbon nitride (g-C3N4) was employed to engineer band structures and construct an S-scheme homojunction (BSCN) for enhanced photocatalytic hydrogen (H2) evolution. The BSCN catalyst exhibited an interwoven architecture of porous nanotubes and nanosheets, providing a large specific surface area and abundant active sites. In situ X-ray photoelectron spectroscopy (XPS) and density functional theory (DFT) calculations revealed an S-scheme charge transfer mechanism at the BCN/SCN interface, driven by a built-in electric field that facilitates efficient spatial separation of photogenerated charge carriers. Photoelectrochemical measurements confirmed improved light harvesting and charge separation. DFT simulations indicated near-thermoneutral hydrogen adsorption free energy (ΔGH* = 0.12 eV) at S-doped sites, favorable for hydrogen evolution reaction (HER) kinetics. The optimized BSCN achieved an exceptional H2 evolution rate of 14.409 mmol g−1 h−1, approximately 75-fold and 3.4-fold higher than pristine BCN and SCN, respectively. This work establishes a rational doping-mediated approach for designing high-efficiency g-C3N4 homojunctions and provides mechanistic insights into S-scheme charge transfer for solar-driven H2 production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4493-8
Metal halide perovskite photovoltaics have achieved power conversion efficiencies rivaling crystalline silicon, yet their transition from laboratory-scale devices to commercial deployment requires a paradigm shift toward application-specific engineering and macroscopic system integration. This review systematically evaluates the customized deployment of perovskite solar cells (PSCs) across diverse operational theaters, including building-integrated photovoltaics (BIPV), portable Internet of Things (IoT) systems, agricultural photovoltaics (Agri-PV), vehicle-integrated photovoltaics (VIPV), utility-scale tandems, and extreme space environments. Despite these opportunities, critical challenges persist in translating laboratory achievements into industrial-scale production. We critically evaluate primary bottlenecks hindering gigawatt-scale commercialization, focusing on the performance gap inherent in large-area manufacturing. Additionally, we analyze intrinsic material instabilities driven by dynamic ion migration and multi-scale lattice strain under realistic outdoor conditions. To conclude, we outline a strategic roadmap for overcoming these barriers, emphasizing lattice strain regulation, rigorous dynamic environmental testing protocols, and comprehensive sustainable lifecycle management. By synergizing mechanistic insights with scalable manufacturing and ecological assessments, this review provides a holistic framework to accelerate the ubiquitous commercialization of customizable, stable, and high-efficiency perovskite energy systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4273-3
Freestanding membranes have driven a profound evolution of strain engineering by fundamentally overcoming the substrate clamping effect. This structural degree of freedom enables the introduction of spatially complex, reversible, and giant strain fields into the membranes via mechanical manipulations such as stretching, bending, and interfacial twisting, ultimately facilitating the modulation of diverse physical properties. This review systematically discusses recent experimental and theoretical advances in the field, highlighting the modulation of physical properties via uniaxial/biaxial strain, strain gradients, and oxide twist. These mechanical strain strategies substantially broaden the range of achievable material properties, furthermore provide fundamentally new pathways for realizing unconventional mechanical behaviors, inducing emergent polar topological structures, and exploring correlated electronic states. Finally, this review summarizes current methodologies for implementing emergent strain engineering of oxide membranes, delves into the profound impacts of spatially complex strain on the fundamental physical properties of freestanding oxides, and offers a forward-looking perspective on the tremendous opportunities and challenges in this rapidly evolving field.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4138-5
Electrocoagulation (EC) has emerged as a promising electrochemical technology for wastewater treatment, offering distinct advantages over conventional chemical coagulation and membrane processes. This review systematically summarizes recent advancements in EC, focusing on the underlying mechanisms, key operating parameters, and diverse technical applications. The EC process involves three stages: electrolytic oxidation and in-situ coagulant formation, destabilization of contaminants, and floc formation. Unlike chemical coagulation, EC requires no external chemical additives, and process control is achieved by adjusting current density, voltage, or electrode materials, enabling adaptation to varying wastewater qualities. The review highlights the influence of dissolved organic matter (DOM) on EC efficiency, as clarified by Luo et al. (Water Research, 2025). Furthermore, it discusses reactor design innovations, including continuous-flow and cascade-type configurations, and the role of current waveforms in mitigating electrode passivation. The integration of EC with membrane bioreactors and forward osmosis is also examined, demonstrating enhanced treatment performance and fouling mitigation. Key challenges, such as energy consumption and electrode scaling, are addressed, along with future research directions. This comprehensive analysis provides a critical framework for optimizing EC systems and scaling them for industrial wastewater treatment, emphasizing the need for holistic reactor design and process integration to achieve sustainable water reuse.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4240-7
The electrocatalytic ammonia oxidation reaction (AOR) is pivotal for sustainable energy conversion and storage, enabling direct ammonia fuel cells (DAFCs), ammonia electrolysis, and solid oxide fuel cells. This review critically examines recent advances in AOR catalysis, emphasizing active-site regulation, interfacial engineering, and device-oriented catalyst development. For noble-metal catalysts, optimizing adsorption and dehydrogenation of NHx intermediates while mitigating poisoning is essential for sustained activity. Non-noble-metal systems, particularly Ni-based catalysts, require precise control of reconstructed working-state phases such as NiOOH-like species to balance activity and selectivity. Interfacial engineering, including heterointerfaces, defect structures, and doped coordination environments, strongly influences the competition between AOR and oxygen evolution reaction (OER), as well as product branching toward N2 or oxygenated nitrogen species. The review underscores that catalyst optimization now extends beyond bulk composition to the precise regulation of the interfacial reaction microenvironment. Furthermore, practical device operation is governed by membrane/electrolyte compatibility, mass transport, ammonia crossover, thermal management, and long-term durability. Bridging fundamental catalyst studies with deployable ammonia energy technologies requires coordinated optimization from active materials to electrode architectures and full-device systems. This review provides a comprehensive framework for designing next-generation AOR catalysts and accelerating their integration into industrial energy systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4244-0
Near-infrared perovskite light-emitting diodes (NIR-PeLEDs) suffer from poor operational stability, largely due to interfacial reactions at the electron-transport layer (ETL)/perovskite interface. Here, we introduce a zinc ion (Zn2+)-chelated hybrid ETL derived from a Zn2+-chelated polyethylenimine ethoxylated (PEIE) complex, which partially retains the surface properties of ZnO but exhibits significantly reduced oxygen defects and surface-adsorbed hydroxyl groups. This well-modulated surface promotes perovskite crystallization and mitigates interface-induced deprotonation of organic cations during device operation. Consequently, NIR-PeLEDs employing this hybrid ETL achieve a peak external quantum efficiency (EQE) of 20.1%, a high radiance of 652 W sr-1 m-2, and an exceptional T50 lifetime of 270.7 hours at a high current density of 100 mA cm-2, which is over five times that of devices based on conventional ZnO nanocrystal (NC) ETLs. Our results present an effective ETL strategy for operationally stable NIR-PeLEDs and thoroughly reveal the critical role of regulating interfacial reactions in stabilizing buried interfacial contacts. These findings provide valuable insights for advancing perovskite optoelectronic devices that suffer from interface-induced performance degradation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4281-7
Multispectral camouflage materials must simultaneously address visible and infrared (IR) detection while maintaining environmental stability and mechanical flexibility for deployment in harsh conditions. This work presents a multilayer composite integrating a colorful, IR-transparent visible reflection (VR) layer, a low-emissivity graphene (LEG) layer, and an aramid nanofiber (ANF) aerogel layer. The VR layer provides tunable visible colors without compromising the low-emissivity property of the LEG layer, which achieves IR emissivity between 0.30 and 0.43. The ANF aerogel, reinforced with a grid structure, reduces thermal conduction, lowering IR radiation intensity by 40% at an 80 °C heat source. The composite exhibits effective electromagnetic interference (EMI) shielding and maintains multifunctional stability in strong acid, strong alkali, saline, and organic media. This design offers a novel strategy for environmentally robust multispectral camouflage materials suitable for extreme operational environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4284-5
This highlight summarizes a recent breakthrough in integrated visual sensing and computing using symmetry-reconfigurable photodiodes (SRPDs). The device architecture comprises a metal-semiconductor-metal configuration with AgBiS2 as the active layer, enabling dynamic symmetry breaking through voltage-controlled silver filament formation. The SRPD exhibits broadband photosensitivity from 360 nm to 1,550 nm at an illumination intensity of 115 mW cm-2, as demonstrated by multiwavelength time-resolved photocurrent responses. The device can be programmed into fifteen distinct photoresponsivity states, facilitating analog memory and neuromorphic computing. In imaging experiments, an SRPD-based sensory chip successfully captured images through visibly non-transparent inked glass at 808 nm, highlighting its capability for information-lossless acquisition in scattering media. Furthermore, the device achieved high-accuracy pattern recognition with nearly zero false neuron outputs when projecting specific patterns (├, ┬, ┤), each correlating to a unique current output. As a proof of concept, real-time eye-tracking control of an unmanned aerial vehicle (UAV) was demonstrated, enabling the UAV to follow and monitor a moving cyberdog. These results underscore the potential of SRPDs for processing-in-sensor applications, neuromorphic vision, and human-machine interfacing, offering a compact solution that merges sensing and computing functionalities.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4261-2
Developing ion exchange membranes with both high proton conductivity and high selectivity is crucial for vanadium redox flow batteries (VRFBs). Commercial Nafion membranes suffer from severe vanadium crossover, while conventional additives often aggregate, disrupting ion domains and significantly reducing proton conductivity. To overcome this conductivity–selectivity trade-off, we propose a modification strategy based on molecular-level functional strategy. Two complementary additives, polyvinylpyrrolidone (PVP) and a fluoroalkyl-grafted polyoxometalate cluster (8FSiW11), are introduced into Nafion matrix to achieve precise, cooperative, regulation of ionic domains. PVP fills ion domains via hydrogen bonding and electrostatic interactions, constructing an efficient barrier against vanadium ions. Simultaneously, 8FSiW11 anchors at the hydrophilic/hydrophobic interface, providing additional proton sources and hopping sites to compensate for proton neutralization by PVP. The resulting hybrid membrane exhibits a proton/vanadium selectivity of 1×10^6 S min cm^-3, 8.6 times higher than commercial Nafion 212 (NR212), and enables VRFB energy efficiencies (EE) of 88.9% at 100 mA cm^-2 and 83.2% at 200 mA cm^-2. This work demonstrates the potential of synergistic molecular modification strategy to break conductivity–selectivity trade-off in membrane design for next-generation high-performance VRFBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4295-5
Carbon nanomaterials (CNMs), including carbon nanotubes, graphene, and fullerenes, exhibit exceptional promise in precision biomedicine due to their tunable biocompatibility, programmable surface chemistry, large specific surface area, and quantum confinement effects. However, their clinical translation is hindered by aggregation, poor physiological dispersibility, and limited targeting specificity. This review systematically elaborates on surface engineering strategies—covalent functionalization, non-covalent assembly, and heteroatom doping—to optimize the multifunctionality, biocompatibility, and targeting capabilities of CNMs at the nano-bio interface. We explore how engineered interfaces enable advanced applications in biosensing, stimuli-responsive drug delivery, multimodal bioimaging, antibacterial therapy, and regenerative tissue engineering. The review also addresses challenges such as scalability, long-term toxicity, and regulatory hurdles, and proposes future directions to expedite clinical adoption. By providing a comprehensive framework for rational surface design, this work aims to bridge the gap between fundamental materials science and clinical needs, offering a roadmap for developing next-generation carbon-based theranostics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4302-9
The pre-deposited lead iodide (PbI2) film in two-step inverted perovskite solar cells (PSCs) often exhibits a dense structure, which impedes the diffusion and reaction of organic ammonium salts, leading to unreacted PbI2 residues and compromised device performance. To address this, 2,4-oxazolidinedione (OD) is introduced as a molecule additive into the PbI2 precursor solution. Owing to its stronger coordination with PbI2, OD effectively modulates its crystallization behavior, resulting in a porous structure. This porous structure significantly facilitates the diffusion and infiltration of organic ammonium salts, thereby minimizing PbI2 residue and enhancing the completeness of the perovskite conversion. Furthermore, OD and the constructed porous network jointly retard the crystallization kinetics of perovskite, promoting the formation of perovskite films with improved crystallinity and preferred crystal orientation. Therefore, the optimized PSCs achieve a power conversion efficiency (PCE) of 26.31%, and demonstrate excellent operational stability, retaining 90.24% of initial PCE for 1500 h at 25°C and 90.47% after 1000 h at 65°C. The champion device exhibits a VOC of 1.197 V, a JSC of 26.28 mA cm-2, and an FF of 83.58%, with negligible hysteresis. This study presents a straightforward yet effective approach to advancing the performance and stability of inverted PSCs fabricated via the two-step method.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4290-9
Thermoelectric materials enable direct and reversible conversion between heat and electricity, offering unique advantages for waste heat recovery, solid-state refrigeration, and deep-space power systems. The performance is evaluated by the dimensionless figure of merit, zT = S²σT/κ, where S is the Seebeck coefficient, σ is the electrical conductivity, T is the absolute temperature, and κ is the total thermal conductivity. Achieving high zT requires simultaneous realization of a large power factor (S²σ) and low thermal conductivity. However, these parameters are intrinsically coupled, posing a fundamental challenge. PbTe is a representative thermoelectric material operating in the intermediate temperature range, with outstanding performance originating from its unique electronic band structure featuring multiple nearly degenerate valence band maxima near the L points. Band convergence via alloying with mono-tellurides such as MgTe, MnTe, CdTe, YbTe, SrTe, and EuTe effectively modifies the valence band structure, increasing band degeneracy and density-of-states effective mass, thereby enhancing electrical conductivity without decreasing the Seebeck coefficient. However, increasing the content of these mono-tellurides limits acceptor dopability, making conventional dopants like Na difficult to incorporate. This study demonstrates that co-doping strategies can preserve dopability while achieving band convergence and dislocation engineering, leading to significantly reduced lattice thermal conductivity and extraordinary peak zT values. The decoupling of electronic and thermal transport through this approach offers a promising route for high-performance thermoelectrics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4260-5
Lithium-sulfur batteries (LSBs) are recognized as a leading candidate for next-generation energy storage due to their high theoretical specific capacity (1675 mAh g⁻¹). However, the shuttle effect of lithium polysulfides (LiPSs) severely limits cycle life and energy efficiency. Here, we report a multi-interface engineering strategy employing a MnO₂-TiO₂@Ti₃C₂ MXene (MT@MX) heterojunction, synthesized via a facile redox reaction between MXene and KMnO₄, to modulate bidirectional polysulfide conversion. The 2D structure with high conductivity and abundant heterogeneous interfaces facilitates fast ion/electron transfer, reduces reaction energy barriers, and enhances adsorption via d-band center effects. The stepped built-in electric field (BIEF) in MT@MX lowers the migration energy barrier of LiPSs from catalytic MXene to TiO₂ and then to adsorptive MnO₂, enabling reversible migration across multi-interfaces. Optimized heterointerfaces synergistically integrate adsorption, diffusion, and catalytic conversion, yielding excellent cycling stability even at a high sulfur loading of 6.4 mg cm⁻². This work demonstrates that constructing heterojunctions with stepped BIEF offers a feasible approach to modulate interfacial diffusion and provides a new design strategy for high-performance LSB electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4303-7
Sodium-ion batteries (SIBs) are promising for grid-scale storage and low-speed electric vehicles, yet their electrochemical behavior is governed by intricate mechanical-electrochemical coupling effects, rendering failure mechanisms not fully understood. Here, we develop an in-situ pressure-electrochemical monitoring system and reveal the failure mechanism of commercial Ah-level NaNi1/3Fe1/3Mn1/3O2//hard carbon (NNFMO//HC) sodium-ion pouch cells. Under an initial external pressure of 500 kPa, the full cell retains 90.07% of its capacity after 500 cycles at 0.5 C. Operating at the optimal pressure of 500 kPa effectively avoids heterogeneous sodium deposition in HC anodes, suppresses gas evolution from electrolyte decomposition, and prevents irreversible phase transitions in NNFMO cathodes during long-term cycling, thereby mitigating capacity degradation. Deviation from this optimal pressure leads to spatially non-uniform sodium deposition, accelerated electrolyte decomposition, and irreversible cathode phase transitions, collectively accelerating capacity fade. This work establishes a quantitative relationship between external pressure and pouch cell degradation, advancing SIBs development and application.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4319-x
This erratum corrects an error in the Acknowledgments section of the original article 'Investigation on graphene growth by roll-to-roll chemical vapor deposition' published in Science China Materials, Vol. 65, Issue 4, page 1042, 2022. The authors regret that the funding number (No. (2021)105) for the Shenzhen Science and Technology Program was incorrectly used. The correct funding number is No. KQTD20200820113010022. The authors apologize for any inconvenience caused. This correction does not affect the scientific content, results, or conclusions of the original paper. The original research focused on the kinetics of graphene growth via roll-to-roll chemical vapor deposition (CVD), a scalable method for producing high-quality graphene films. The study addressed challenges in continuous manufacturing, such as uniformity, growth rate, and defect control, and provided insights into optimizing process parameters for industrial-scale production. The erratum ensures accurate attribution of funding sources, maintaining the integrity of the research record.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4339-7
Neuromorphic computing demands energy-efficient synaptic devices that emulate biological plasticity. Optoelectronic memristors based on colloidal quantum dots (QDs) offer tunable bandgaps and solution processability, yet suffer from defect-mediated nonradiative recombination and instability. Here, we report ZnS-passivated CdZnSe core/shell QDs as the active layer in memristive devices, achieving enhanced synaptic emulation and information encryption. Time-resolved photoluminescence (TRPL) decay curves were fitted with a tri-exponential function, revealing that ZnS passivation suppresses defect-related trap states, prolonging the average carrier lifetime from 12.3 ns (CdZnSe) to 28.7 ns (CdZnSe/ZnS). The intensity proportion of the fast decay component (τ1 ≈ 1.2 ns) decreased from 45% to 18%, indicating reduced surface trapping. Devices incorporating CdZnSe/ZnS QDs exhibit stable bipolar resistive switching with an ON/OFF ratio exceeding 10^3, endurance of >10^3 cycles, and retention of >10^4 s. Under 365 nm UV illumination, the devices show light-tunable synaptic plasticity, including paired-pulse facilitation (PPF) with a facilitation index of 180% at a 50 ms interval, and transition from short-term to long-term memory. The memristors successfully emulate essential synaptic functions and are employed in a simple encryption scheme, demonstrating the potential of defect-passivated QDs for secure neuromorphic hardware.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4340-0
Thin films with nonreciprocal circularly polarized luminescence (CPL) emit circularly polarized light with opposite handedness from its two opposite sides, holding great promise for advancing optical multiplexing technologies. Herein, we introduce component orientation mismatch into chiral composite films via stretching, which leads to macroscopic optical anisotropy and accordingly drives the films to show nonreciprocal CPL activity. Stretching triggers linear dichroism-linear birefringence (LD-LB) coupling to realize nonreciprocal circular dichroism (CD) in elastomer films consisting of thermoplastic polyurethane (TPU) and chiral polyacetylene (R/S-PSA). Moreover, fluorescence anisotropy-linear birefringence (f-LB) coupling occurs after introducing fluorescent groups into the films to achieve multi-color nonreciprocal CPL. The unstretched films exhibit reciprocal CPL with a luminescence dissymmetry factor (|glum|) of 10⁻¹, with handedness determined by PSA’s intrinsic helical chirality. In the stretched films, the oriented fluorescent groups undergo f-LB coupling with matrix crystallization, resulting in nonreciprocal CPL (|glum|=10⁻²). Based on this distinctive chiroptical feature, we have developed chiral logic gates, multidimensional optical encryption systems, and enantioselective photopolymerization platforms to demonstrate the potential uses of the as-obtained CPL films. This work provides both fundamental insights into and a versatile material platform for developing smart nonreciprocal photonic systems with advanced chiroptical functionality.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4250-0
Shape memory polymer (SMP)-based transfer printing offers a promising route for heterogeneous integration of flexible electronics, yet non-contact release reliability remains a critical bottleneck. This study systematically investigates the influence of pickup heating modes—localized versus global—on the release yield and energy-delivery mechanisms through combined experiments and finite element simulations. The localized heating mode concentrates strain energy at the interface, enabling controlled chip ejection with high yield, whereas global heating dissipates energy, leading to release failure. Quantitative analysis reveals that localized heating achieves a release yield of 100% under optimized conditions, compared to near-zero for global heating. The ejection velocity under localized heating is higher, which may induce chip bouncing on the receiver substrate, affecting transfer accuracy; however, this can be mitigated by adjusting release gap and laser parameters. The findings establish a theoretical framework for energy pathway design, providing guidelines for achieving high-yield, accurate non-contact release in laser-induced transfer printing. This work advances the practical application of SMP-based transfer printing for micro-LED displays and flexible electronics, addressing a key manufacturing bottleneck.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4344-5
Germanium-based materials (Ge-based) have been explored as anodes for potassium-ion batteries (PIBs) due to their high theoretical capacity (369 mAh g-1) and moderate potassium insertion potentials. However, their application is hindered by volume expansion and unstable solid electrolyte interphase films. This review systematically synthesizes recent advances in Ge-based materials (encompassing metallic Ge, oxides, chalcogenides, and alloys), with an emphasis on structure-performance relationships to elaborate synergistic optimization strategies. Key optimization strategies such as nanostructuring, composite design with conductive supports, interfacial engineering, doping, and electrolyte modification are elaborated. The potassium storage mechanisms of different materials are compared, and the effectiveness of various modification strategies is evaluated under different operating conditions. High-throughput computations are integrated with experimental validation to guide material and electrolyte design. A life cycle assessment perspective is also introduced to evaluate the sustainability and practical viability of Ge-based materials. Given the high cost and low abundance of Ge, these materials are more suitable for niche applications where high energy density is critical, rather than large-scale grid storage. The review underscores the necessity of balancing electrochemical performance with economic and environmental considerations, proposing a roadmap for future research that prioritizes cost-effective synthesis and scalable manufacturing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4202-3
Carbon dots (CDs) with absorption in the second near-infrared window (NIR-II, 900-1700 nm) hold promise for tumor theranostics, yet existing synthesis methods often involve complex procedures, harsh conditions, or lack precise control. Here we report a 'self-photooxidation-restructuring' strategy that enables structural reorganization of the carbon core in CDs, achieving a significant redshift of absorption into the NIR-II region. Under ultraviolet (UV) light irradiation, the precursor (B-CDs, absorption in UV region) generates singlet oxygen, which self-oxidizes aldehyde groups and the carbon skeleton of B-CDs to stronger electron-withdrawing carboxyl groups and carbon radicals, respectively. These processes facilitate the formation of new C=C bonds between isolated aromatic domains, thereby transforming B-CDs into novel CDs (N-CDs) characterized by enhanced donor-acceptor interactions and a redshift in absorption toward the NIR-II window. Various experimental data, including high-resolution XPS, FTIR, NMR, EPR, have proved the proposed formation mechanism. The novel N-CDs afforded a high photothermal conversion efficiency of up to 71.33%, which enabled 1064 nm laser-activated photoacoustic imaging (PAI)-guided photothermal therapy (PTT) in tumors. This work opens a new avenue for the synthesis and modulation of CDs in the NIR-II region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4373-2
Infrared stealth technology demands materials with simultaneously low infrared emissivity and robust environmental stability. Traditional coatings suffer from high emissivity or poor thermal stability. Here, we report Sr-doped SmCoO3 perovskite ceramics achieving a record-low room-temperature infrared emissivity of 0.12 in the 8–14 μm atmospheric window. Systematic doping (x = 0, 0.1, 0.2, 0.3, 0.4, 0.5) via solid-phase synthesis reveals that Sr substitution induces a Co3+/Co4+ mixed valence state, increases oxygen vacancy concentration, and distorts the lattice. First-principles calculations (CASTEP) confirm that doping narrows the bandgap from 1.8 eV to 0.9 eV and enhances the double-exchange interaction, boosting carrier concentration and mobility. The optimized composition (x = 0.3) exhibits an electrical conductivity of 1.2×10^3 S/cm and a carrier density of 3.5×10^21 cm^-3, leading to strong infrared reflection. The material maintains emissivity below 0.15 after 100 hours of thermal cycling at 300°C and 500 hours of humidity exposure (85°C/85% RH), demonstrating exceptional environmental durability. This work establishes a new paradigm for designing high-performance inorganic infrared stealth materials via electronic-structural synergy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4342-3
Electron acceptors containing single-bond-linked building blocks offer attractive advantages for organic solar cells owing to their synthetic simplicity and structural modularity. However, achieving backbone planarity without compromising electronic compatibility remains a persistent challenge. Conventional conformational locking strategies based on alkoxy substitution can effectively suppress torsional freedom but often elevate the highest occupied molecular orbital energy level, limiting compatibility with widely used donor polymers. Here, we report a partially fused electron acceptor design that achieves intrinsic backbone planarity through heterocycle selection rather than side-chain-assisted conformational locking. By incorporating a benzodifuran core and furan-thiophene linkages, the resulting acceptors exhibit a near-coplanar backbone geometry as revealed by density functional theory calculations, without the need for electronically perturbing alkoxy groups. Devices based on the optimized acceptor (BDF-1) deliver a binary power conversion efficiency of 12.2%, and further improvement to 19.5% is achieved in a ternary blend with PM6 and BTP-eC9. The enhanced performance is accompanied by favorable morphology, balanced charge transport, and suppressed recombination losses. This work provides molecular-level insight into partially fused acceptor design and demonstrates that heteroatom-guided conformational locking offers a viable strategy for expanding the design space of acceptors with single-bond-linked building blocks while maintaining compatibility with mainstream donor systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4394-x
Spiral graphene, characterized by Bernal-stacked layers and unique electronic properties, holds promise for advanced quantum and optoelectronic devices. However, its controlled synthesis remains challenging. Here, we report the self-assembly growth of single-crystal spiral graphene on a liquid heterogeneous substrate via chemical vapor deposition (CVD). A 50-μm-thick Cu foil was placed on a Ni support and heated to 1083 °C, the melting point of pure Cu, ensuring a fully molten Cu layer on solid Ni. Growth proceeded for 30 minutes under optimized conditions. The resulting spiral graphene exhibits a uniform Bernal stacking configuration, as confirmed by transmission electron microscopy and selected-area electron diffraction. Time-of-flight secondary ion mass spectrometry (ToF-SIMS) depth profiling and isotope-labeling experiments reveal that carbon incorporation occurs predominantly at the spiral step edges, following a self-assembly mechanism driven by the liquid substrate's dynamic surface. Control experiments on solid Cu-Ni alloys yield no spiral morphology, underscoring the critical role of the liquid phase. The liquid heterogeneous substrate facilitates rapid carbon diffusion and step-edge attachment, enabling the growth of high-quality single-crystal spirals with controlled layer number. This work provides a scalable route to synthesize spiral graphene with tailored stacking, advancing its application in twistronics and high-performance electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4381-5
Bismuth telluride (Bi2Te3)-based alloys remain the benchmark for low-temperature thermoelectric applications, yet their conversion efficiency is limited by the trade-off between electrical and thermal transport. This study introduces a pseudo grain boundary engineering strategy to simultaneously enhance the average figure of merit (ZT) in p-type (Bi,Sb)2Te3 (BST) materials. By incorporating Ag-based compounds, the carrier concentration is optimized via substitution of Ag+ ions, while the introduction of secondary phases at grain boundaries effectively suppresses lattice thermal conductivity. The approach yields a peak ZT of 1.35 at 393 K and an average ZT of 1.25 across 303–483 K, representing a significant improvement over pristine BST. Compared to prior reports, this work achieves superior average ZT while maintaining high electrical conductivity, addressing the longstanding bottleneck of thermal conductivity reduction without compromising carrier mobility. The findings underscore the efficacy of pseudo grain boundary engineering in advancing Bi2Te3-based thermoelectrics for solid-state cooling and power generation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4376-3
Single-molecule localization microscopy (SMLM) surpasses the diffraction limit to achieve molecular-scale resolution, but conventional probes suffer from photobleaching, limiting imaging duration. In a recent Nature Photonics article, Ren and co-workers introduced spontaneous photoblinking upconversion microscopy (SPUM) using Yb3+/Ho3+ co-doped core–shell–shell upconversion nanoparticles (UCNPs, NaYF4@NaYb/HoF4@NaLuF4). These UCNPs exhibit exceptional photostability and persistent, reversible blinking under 976 nm continuous-wave excitation, with negligible photodegradation. The blinking mechanism involves a Yb3+ multiphoton process coupled with defect-mediated energy trapping, switching the UCNPs between emissive (on) and non-emissive (off) states. Kinetic analysis revealed single-exponential bright-state dwell times and biexponential dark-state dwell times, indicating one decay pathway into a non-emissive state and two recovery pathways. In live-cell imaging, synchronized transport of UCNPs maintained constant interparticle distance and near-unity positional correlation. In fixed cells, Fourier ring correlation (FRC) resolution reached 30 nm, confirming sub-50 nm performance in biological specimens. This work provides an unprecedented combination of low duty cycle and photostability, establishing a foundation for non-photobleaching luminescent nanomaterials in long-term super-resolution imaging and nanoscale tracking.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4368-y
Stretchable pixelated electronic devices face a fundamental design conflict: accommodating mechanical deformation while preserving a high fill factor of active photosensitive elements. Conventional strain-relief strategies, such as pop-up, serpentine, and kirigami structures, rely on geometric unfolding that inevitably consumes inactive area, reducing pixel density and compromising photoresponse intensity, spatial resolution, and signal-to-noise ratio. In a recent breakthrough published in Nature Materials, Park et al. demonstrated a high-fill-factor silicon–liquid metal pixelated platform for multiscale visual acquisition and depth perception. The device integrates ~700-nm-thick ultrathin single-crystalline silicon photodiodes, finely patterned liquid metal interconnects, and a styrene–butadiene–styrene (SBS) elastomer substrate. The silicon pixels provide high-performance photoelectric conversion, while the liquid metal interconnects accommodate deformation, achieving a functional separation that mitigates the trade-off between pixel density and mechanical compliance. The device maintains stable photodiode characteristics and repeatable photoresponses under high-curvature hemispherical stretching and large biaxial tensile strain. Two applications were demonstrated: a human-eye-inspired robotic vision system with a curved photosensitive surface for wide-field imaging, and an epidermal, lensless, near-contact imaging device for close-range image acquisition. These systems enable multiscale visual acquisition and depth perception, offering a scalable route for future stretchable visual electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4201-0
Open fracture fixation faces dual critical challenges: bacterial infection and impaired bone healing. This study presents a rationally designed biomacromolecular network coating (Ti-GOED) on titanium alloy bone plates to simultaneously address these issues. The coating integrates antimicrobial and osteogenic components, achieving an optimal balance between antibacterial efficacy and biocompatibility. In vitro assays demonstrated that Ti-GOED eliminates over 99% of common pathogenic bacteria by inhibiting peptidoglycan synthesis, disrupting bacterial cell wall formation, compromising membrane integrity, and leading to intracellular DNA leakage and bacterial death. Concurrently, Ti-GOED enhances the proliferation and osteogenic differentiation of bone marrow mesenchymal stem cells (BMSCs) via activation of the PI3K-Akt and HIF-1 signaling pathways. In vivo animal experiments confirmed strong antibacterial and osteogenic properties. This work provides a strategy for developing antibacterial coatings on medical devices, with significant potential for preventing and treating infections post-fracture fixation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4292-4
The vast compositional space of high-entropy materials presents a fundamental challenge for catalyst discovery. Considering 21 candidate elements at a 1% atomic resolution, this combinatorial explosion exceeds 10 billion (>10^10) possibilities, rendering direct experimental exploration impractical. Furthermore, purely data-driven approaches often struggle to comprehend the intrinsic chemical roles of discrete elemental identities, yet they excel at mapping continuous concentration gradients. Recognizing this distinction, we transform this combinatorial explosion into a targeted optimization problem by decoupling elemental selection from compositional ratio refinement. Ultrafast carbon thermal shock (CTS) is first employed to screen viable elemental combinations and establish an optimal quinary framework. Machine learning (ML) is subsequently applied to optimize compositional ratios within this reduced space, where statistical modeling efficiently navigates the remaining high-dimensional landscape. Targeting the oxygen evolution reaction (OER) as a proof-of-concept, our hybrid framework pruned the search space from over 10^10 possible compositions down into 13 systems, ultimately identifying high-entropy oxide (HEO)-Fe17.57Co28.45Ni31.27Mo10.57Zr12.14 as the optimal catalyst. The optimized high-entropy oxide exhibits an overpotential of 240 mV at 10 mA cm−2 and sustains stable operation at 1 A cm−2 for over 600 h in 1 M KOH. Mechanistic analysis reveals that Mo electronically tunes oxygen-intermediate adsorption, while Zr enhances structural robustness, collectively enabling high activity and durability. This work demonstrates that bridging discrete physical screening with continuous data-driven optimization provides an efficient and generalizable pathway for navigating high-dimensional material frontiers.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4108-1
Heterogeneous catalysis underpins modern energy conversion, chemical manufacturing, and environmental remediation, yet its advancement is constrained by the scarcity and cost of noble metals. A sustainable alternative lies in activating intrinsically inert sites in earth-abundant materials such as transition metal oxides and carbon-based materials. This review systematically outlines recent advances in activating inert sites within low-cost catalytic materials. We begin by dissecting the physicochemical origins of catalytic inertness, including local atomic symmetry, electronic spin states, and coordination environments. Subsequently, we elucidate mechanisms by which multi-scale strategies—structural engineering, quantum state engineering, and microenvironment engineering—break symmetry, modulate spin states, and construct unique reaction microenvironments, transforming spectator atoms into highly efficient active centers. The review highlights performance breakthroughs in key reactions such as oxygen evolution reaction (OER) and alkane dehydrogenation, where catalytic metrics now rival or surpass noble metal benchmarks. For instance, triangular-ordered Co atoms achieve ampere-level hydrogen production, and tensile strain engineering activates inert non-defect Bi sites for CO2 electroreduction. We critically assess challenges—stability, scalable synthesis, and cost-effectiveness—that hinder industrial translation. Future directions emphasize multi-strategy synergy and artificial intelligence-assisted rational design. This review provides theoretical guidance and technological pathways for subverting noble-metal-dependent paradigms and developing next-generation efficient, low-cost catalytic systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4385-1
Self-assembled monolayers (SAMs) are effective hole-selective contacts for inverted perovskite solar cells, but scalable deposition on rough substrates is hindered by molecular aggregation, disordered packing, and incomplete adsorption. We propose a hybrid strategy incorporating 4-(Piperidin-4-yl)butanoic acid hydrochloride (PBACl) into the 4PABCz solution during dip-coating. PBACl suppresses aggregation via hydrogen bonding and ionic interactions, yielding homogeneous coverage and improved wettability. The piperidine and carboxyl groups passivate buried interfacial defects through hydrogen bonding and coordination with perovskites. Small-area cells achieve a champion power conversion efficiency (PCE) of 26.09%, while a 5 cm × 5 cm mini-module (aperture area 14.4 cm²) delivers 23.29% PCE. Encapsulated devices retain 80% of initial PCE after 1350 h maximum power point tracking under continuous illumination. This ion modulation strategy bridges molecular-level interface control with scalable processing, offering a pathway to industrially relevant perovskite photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4378-6
Electrical stimulation (ES) is a powerful strategy to mimic endogenous bioelectricity and accelerate complex tissue regeneration, such as chronic wound healing. However, aligning external stimulation with native bioelectrical and biochemical signals for rapid and scarless tissue regeneration remains challenging. Here, we report a wireless bioelectronic dressing (E-dressing) that establishes stable bioelectronic interfaces and precisely modulates cellular physiological activities. Bioactive allylamine-functionalized gold clusterzymes (AM-AuNCs) with intrinsic superoxide dismutase-like activity were designed as functional modifiers to co-polymerize with acrylic acid (AA), forming conductive p(AA-AuNCs) hydrogels. AM-AuNCs impart the hydrogel with superior antioxidant activity, robust interfacial adhesion, and high conductivity, enabling rapid hemostasis, efficient electrical stimulation transmission, and precise fibroblast regulation. Combined with 1.00 V of electrical stimulation, the p(AA-AuNCs) hydrogel significantly promotes fibroblast proliferation, migration, and alignment by upregulating TGF-β, FGF-2, and EGF. Integrated with a biocompatible, flexible zinc-ion battery delivering sustained and tunable electrical signals for over 7 days, the E-dressing precisely guides collagen remodeling, inhibits myofibroblast activation, and maintains Col I/Col III balance, leading to a 5-fold acceleration of wound closure and a 65.5% reduction in scar formation. This multifunctional E-dressing represents a promising bioelectronic device for precise cellular regulation and multimodal regenerative therapy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4369-1
Sodium-ion batteries (SIBs) are promising alternatives to lithium-ion batteries for large-scale energy storage due to sodium's abundance and low cost. Among cathode materials, polyanionic compounds like Na3V2(PO4)2O2F (NVPOF) offer high energy density and dual voltage plateaus at ~3.6 and 4.0 V, but suffer from low electronic conductivity and sluggish Na+ diffusion. Here, we report a dual-modulation strategy combining high-valence Nb5+ doping and polydopamine-derived carbon coating to synthesize Na3V1.94Nb0.06(PO4)2O2F-C (NVPOF-Nb-C) via a hydrothermal route. X-ray diffraction and Rietveld refinement confirm that Nb5+ doping induces slight lattice expansion without altering the tetragonal I4/mmm framework. Density functional theory calculations reveal that Nb5+ doping optimizes the crystal structure and reduces the Na+ diffusion barrier, while the uniform carbon coating enhances electron transport. Consequently, NVPOF-Nb-C exhibits remarkably improved electrochemical performance, including high reversible capacity, excellent rate capability, and ultralong cycling stability. In a full cell with hard carbon anode, it delivers a high energy density of 487.2 Wh kg−1 at 1C and retains 91.51% capacity after 3000 cycles at 20C. This work provides a synergistic strategy to overcome the intrinsic limitations of polyanionic cathodes for practical SIB applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4205-8
The global energy crisis and environmental pollution necessitate efficient recovery and utilization of thermal energy resources such as industrial waste heat. Thermoelectric materials, enabling direct conversion between thermal and electrical energy, offer broad application prospects in waste heat power generation and chip cooling. The energy conversion efficiency is determined by the dimensionless figure of merit, ZT = (S^2σ/κ)T, where S is the Seebeck coefficient, σ is the electrical conductivity, κ is the thermal conductivity, and T is the absolute temperature. Ideal thermoelectric materials require both a high power factor (PF = S^2σ) and low thermal conductivity. However, the strong coupling between electrical and thermal transport parameters makes synergistic optimization challenging. Over the past two decades, strategies such as band engineering, nanostructuring, liquid-like ions, interstitial atoms, phonon softening, and defect engineering have been explored. Among these, entropy engineering has emerged as a novel strategy that achieves synergistic optimization by introducing multiple components to increase configurational entropy. High entropy materials, originating from alloys, are defined as multi-principal element systems with five or more elements in near-equiatomic ratios forming single-phase solid solutions. The molar configurational entropy ΔS_conf = R∑x_i ln x_i, with materials classified as high entropy (ΔS_conf > 1.5R), medium entropy (1R < ΔS_conf < 1.5R), or low entropy (ΔS_conf < 1R). Four core effects are summarized: high entropy effect, lattice distortion effect, sluggish diffusion effect, and cocktail effect. Research has expanded from alloys to oxides, chalcogenides, and half-Heusler compounds. This review systematically summarizes the mechanisms by which lattice distortion in high entropy materials affects electrical and thermal transport, and discusses optimization strategies for thermoelectric performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4206-6
Precise patterning of highly ordered organic semiconductor (OSC) thin-film arrays is critical for next-generation electronics. We report a ladder-like polysilsesquioxane (LPSQ) strategy to synthesize two functional analogs with tunable surface energies and robust dielectric properties. These LPSQ dielectrics, functionalized with alkyl or fluoroalkyl side chains, serve dual roles as gate insulators and patterning layers to guide blade-coating of 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT). This approach yields highly aligned arrays suitable for three-dimensional integration in flexible electronics. Synergistic combination of dense LPSQ dielectric packing and aligned semiconductor domains leads to excellent organic thin-film transistor (OTFT) performance, achieving approximately four-fold improvement in field-effect mobility compared to conventional silicon oxide dielectrics. Patterned LPSQ dielectrics enable high-resolution C8-BTBT patterning on plastic substrates, supporting 4-inch-scale 3D integration of flexible logic circuits, including inverters (voltage gain >100), NOR gates, and NAND gates. This work provides a scalable route to high-performance, large-area flexible organic circuits.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4315-2
High-temperature X-ray imaging demands scintillators with high crystallinity, efficient scintillation, and robust thermal stability, yet suitable materials remain scarce. Here, we report an ultra-high-crystallinity transparent glass-ceramic (GC) scintillator strategically designed via controllable heat-treatment-induced crystallization. A sequential precipitation method is employed, where cubic CaF2 nanocrystals initially form, subsequently promoting heterogeneous nucleation and growth of hexagonal BaAl2Si2O8. Intrinsic nanoscale phase separation into F-rich and O-rich domains significantly reduces atomic diffusion distances, yielding an unprecedented crystallinity of up to 97.6%. Notably, defect traps (oxygen vacancy defects, likely located within the lattice or at crystalline/amorphous interfaces) enable efficient carrier capture and thermally stimulated release, contributing to remarkable resistance to thermal quenching. Consequently, the GC scintillator maintains 90.6% of its integrated X-ray excited luminescence (XEL) intensity at 300 °C, with the integrated XEL intensity reaching 94.2% of commercial Bi4Ge3O12 (BGO) at room temperature. This enables stable high-temperature X-ray imaging with a spatial resolution of ~10.4 lp mm−1 up to 225 °C. This work provides a versatile pathway for developing high-sensitivity scintillators for extreme-environment X-ray imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4220-x
High-temperature electronics demand non-volatile memories (NVMs) capable of stable operation above 500 °C for applications in space exploration, nuclear energy, and autonomous driving. Conventional silicon-based devices fail above ~250 °C, and silicon carbide (SiC) cannot process data above 300 °C. Memristors offer a promising solution due to their simple structure, low power consumption, and scalability. A recent breakthrough by Yang et al. (Science) demonstrated a graphene (Gra)/HfOx/W memristor achieving data retention at 700 °C, with retention time of 50 h, endurance of 10^9 cycles, ON/OFF ratio exceeding three orders of magnitude, and operation voltage ~1.5 V. The key innovation is replacing the Pt bottom electrode with in-situ grown graphene, which suppresses high-temperature diffusion of the W top electrode through the HfOx layer. In contrast, Pt/HfOx/W devices fail after annealing at 800 °C for 10^4 s due to W migration, forming conductive filaments that lock the device in the ON state. High-resolution TEM and EDS reveal tungsten oxide (WOx) formation at the W/HfOx interface in Pt-based devices, while Gra-based devices show no such degradation. STEM-EELS confirms W migration across the HfOx layer in Pt devices, but graphene acts as a diffusion barrier, preserving stable switching behavior. This interfacial engineering approach provides a viable pathway for high-temperature NVM, addressing the critical bottleneck of electrode diffusion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4235-6
Fluorite-structured oxides (HfO2, ZrO2) are promising for resistive random-access memory (RRAM) due to their scalability and tunable properties. However, achieving high resistive switching on/off ratios remains challenging. Here, we report a collaborative strategy combining Hf/Zr ratio optimization and Lu3+ doping to regulate band structure and oxygen vacancy concentration in Hf0.4Zr0.6O2 (LHZO) thin films. The resulting LHZO devices exhibit a resistive switching ratio of 8.4 × 10^4, two orders of magnitude higher than that of ZrO2 (1.2 × 10^3). Electrical characterization and synchrotron radiation photoemission spectroscopy reveal that Lu doping widens the bandgap to 4.95 eV, downshifts the valence band, and introduces defect states, collectively suppressing p-type conductivity and reducing off-state leakage current. Simultaneously, Lu3+ doping enriches oxygen vacancies, stabilizing ohmic conductive filaments in the on-state. This co-optimization of band structure and oxygen vacancies effectively enhances insulating properties in the high-resistance state and ohmic conductivity in the low-resistance state, leading to superior resistive switching performance with robust retention (>10^4 s). Our findings establish a fundamental strategy for tailoring electronic properties of doped HfZrO2 thin films toward high-performance RRAM applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4180-9
Developing highly active and stable electrocatalysts based on the lattice oxygen mechanism (LOM) for the oxygen evolution reaction (OER) represents a significant challenge in water splitting. Herein, we successfully introduce oxygen vacancies (Ov) into high-entropy MnFeCoNiCu layered double hydroxides (HE-LDHs) via a solution chemical reduction method utilizing a defect engineering strategy. By precisely tuning the concentration of oxygen vacancies, we effectively activate the lattice oxygen within the HE-LDHs. The optimized Ov-rich high-entropy LDHs (Ov-HE-LDHs) exhibit excellent OER catalytic performance, achieving a current density of 10 mA cm−2 with a remarkably low overpotential of only 210 mV in 1.0 M KOH electrolyte, which is substantially superior to pristine HE-LDHs (315 mV) and commercial IrO2 (330 mV). Furthermore, the catalyst demonstrates outstanding long-term stability, capable of stable operation for 500 h at a high current density of approximately 200 mA cm−2. Advanced X-ray absorption fine structure analysis elucidates the lower metal valence states, indicating the existence of oxygen vacancies, while isotope labeling experiments and in-situ electrochemical Raman spectroscopy strongly confirm the successful activation of the LOM pathway. Density functional theory calculations further validate that the shift in the OER mechanism towards LOM and the resulting reduction in the reaction energy barrier are the fundamental reasons for the catalyst’s enhanced intrinsic activity. This work proposes a novel strategy for activating lattice oxygen in high-entropy LDHs through defect engineering, offering new insights and experimental guidance for the design and development of highly efficient and stable high-entropy OER electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4113-3
Constructing abundant grain boundary defects is a promising strategy for developing high-efficiency catalysts. However, achieving dense grain boundary defects in CuO and Cu at the nanoscale remains challenging. Inspired by Turing patterns in nature, a Turing-type CuO catalyst (TGB-CuO) with abundant grain boundaries at ~10 nm nanoscale was prepared by annealing a dodecyl sulfate-intercalated basic copper carbonate. The balanced diffusion-reaction dynamics during pyrolysis drove the spontaneous formation of Turing-type grain boundary architectures in TGB-CuO. The resulting TGB-CuO electrode exhibited outstanding performance in electrochemical CO2 reduction (ECO2RR), delivering a Faradaic efficiency of 80.15% toward multi-carbon (C2+) products and maintaining over 50% ethylene selectivity at 300 mA cm−2 for 30 h of continuous operation. Activity investigations indicated that the metallic Cu retaining Turing-type grain boundary features (TGB-Cu) formed during electroreduction was responsible for the enhanced ECO2RR performance. The Cu(100)/(100), Cu(100)/(111), and Cu(111)/(111) grain boundaries promoted CO2 activation and *CO adsorption, while lowering the free energy barriers for the rate-determining *CO2− → *COOH step and C–C coupling step. This bioinspired reaction-diffusion strategy offers a new paradigm for creating high-density grain boundary defects, offering a general route toward efficient catalyst design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4277-1
Two-dimensional (2D) magnetic materials hold promise for next-generation spintronics, yet most exhibit Curie temperatures (Tc) far below room temperature, limiting practical applications. Here, we report the realization of room-temperature ferromagnetism in CuCrSe2 nanosheets via controlled anion removal achieved by post-synthetic vacuum annealing. Raw CuCrSe2 shows a low Tc of ~120 K, whereas annealed CuCrSe2 (A-CuCrSe2) nanosheets exhibit robust ferromagnetic ordering above 300 K. Structural and compositional analyses, including transmission electron microscopy, Raman spectroscopy, and X-ray absorption spectroscopy, confirm that A-CuCrSe2 retains the original layered crystal structure with an estimated Se vacancy concentration of approximately 10%. Magnetic measurements reveal room-temperature ferromagnetism in exfoliated nanosheets, corroborated by magnetic imaging and electric transport measurements. Anomalous Hall effect (AHE) measurements uncover the coexistence of two ferromagnetic phases within the same sample: one with low Tc (~120 K) and another with high Tc (>300 K), indicating spatially heterogeneous magnetic ordering driven by anion removal distribution. Density functional theory (DFT) calculations elucidate the microscopic mechanism, suggesting that Se vacancies modulate the magnetic exchange interactions, enhancing Tc. This work demonstrates that anion modulation is an effective intrinsic strategy to achieve room-temperature ferromagnetism in 2D materials, potentially advancing spintronic applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4237-x
Silicon-based (Si-based) anodes are core candidates for next-generation high-energy solid-state batteries (SSBs) due to their high theoretical capacity (~4200 mAh g−1). However, their practical application is constrained by the 'size effect', which influences mechanical integrity and electrochemical performance. This review systematically examines the failure mechanisms of nano-silicon (nSi) and micro-silicon (mSi) anodes when paired with sulfide and organic-inorganic composite solid-state electrolytes (SSEs). Key functional parameters of these SSEs are discussed, along with strategies to mitigate interfacial impedance and accommodate volume changes. Recent progress in structural and interface modifications is highlighted, including the use of hard-carbon-stabilized Li–Si anodes (achieving stable cycling) and pressure-free operation. The review identifies core challenges, such as achieving intimate solid–solid contact and managing mechanical stress, and outlines future directions for 'size effect' regulation to accelerate commercialization of high-energy Si-based SSBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4159-y
The electrocatalytic oxidation of ethylene glycol (EG) derived from polyethylene terephthalate (PET) waste to valuable glycolic acid (GA) represents an attractive route for waste resource upcycling. However, achieving high selectivity remains challenging due to the difficulty in steering the complex reaction pathway. In this study, PdPtCuInBi high-entropy intermetallic metallene (HEI-PdPtCuInBiene) is reported to precisely control EG oxidation reaction (EGOR) pathway for GA production by constructing multiple active sites at the atomic scale. In PET hydrolysate, it achieves a Faradaic efficiency of 99.87% and a production rate of 1.47 mmol h−1 cm−2, along with excellent stability. Mechanistic studies reveal that the high-entropy structure induces strong p-d orbital hybridization, which optimizes the electronic structure of active sites, thus weakening the adsorption of key carbonyl intermediates and suppressing C–C bond cleavage. The synergistic electronic effect among Pd, Pt, and Cu further enables differential adsorption of distinct intermediates on diverse active sites, enhancing the selective formation of GA. Techno-economic analysis exhibits high profitability (~$784.9 t−1 PET) of this route, demonstrating the great potential of high-entropy intermetallic metallene in regulating electrocatalytic upcycling of PET waste and beyond.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4234-3
The pursuit of high-energy-density sodium-ion batteries (SIBs) necessitates the development of stable high-capacity anodes. While amorphous carbon is a promising anode candidate for SIBs, its practical application is hindered by limited capacity. Herein, we design a composite anode by chemically confining a high-content (~25 wt%) short-chain sulfur into hierarchical porous hard carbon microspheres (SHHC) derived from microbe yeast. The SHHC anode exhibits a high reversible capacity of ~807 mAh g−1 at 0.03 A g−1 (~3 times that of conventional amorphous carbon) along with superior rate capability, and extraordinary long-term cyclability (almost 100% capacity retention after 2000 cycles at 1.0 A g−1). The high-content sulfur species contribute to superb redox reactivity for high-capacity sodium storage via a surface-dominated storage mechanism. The carbon matrix features an enlarged interlayer distance, which facilitates Na-ion intercalation and deintercalation for high-rate capability. Furthermore, the hierarchical porous structure with built-in cavities facilitates the Na-ion transfer and effectively accommodates the electrode’s volume expansion, achieving fast electrode kinetics and outstanding cyclability. Such a combination of favored properties leads to state-of-the-art comprehensive battery performance for Na-ion storage. Our finding envisions a new perspective on building stable high-capacity anode materials for SIBs.