SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4419-1
Proton exchange membrane fuel cells (PEMFCs) fed with reformate hydrogen suffer severe anode poisoning by trace CO, necessitating high CO electrooxidation potentials that degrade performance and durability. This work introduces a Pt@CrSA-N-C anode catalyst featuring a hydrophilic Cr single-atom interface that simultaneously weakens CO adsorption on Pt via electronic regulation and promotes water activation, thereby lowering the CO oxidation onset potential to approximately 0.13 V vs. RHE. The onset potential was determined by two independent methods: the first potential at which the background-corrected current exceeds 0 mA cm-2 during CO oxidation reaction tests in a three-electrode system, and the potential at which the forward scan current exceeds the N2 background current in CO-stripping voltammetry. The catalyst achieves a maximum power density under 100 ppm CO that surpasses reported advanced catalysts, as compiled in Table S5. Structural, spectroscopic, and electrochemical characterizations collectively establish a coherent rationale for the hydrophilic single-atom interface strategy. This approach addresses the longstanding trade-off between CO tolerance and Pt utilization, offering a viable route for low-potential CO removal in practical PEMFC anodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4312-8
Carbazole phosphonic acid-based self-assembled molecules (SAMs) serve as effective hole-selective contacts in organic solar cells (OSCs), yet their molecular packing and aggregation behavior during solution processing remain difficult to control, limiting hole transport and device durability. This study introduces a polymer-templated self-assembly strategy to regulate molecular organization by one-step spin-coating a blend of [2-(9H-carbazol-9-yl)ethyl]phosphonic acid (2PACz) and PEDOT:PSS. The polycationic PEDOT+ framework acts as a template, providing supplementary anchoring interactions that promote ordered molecular arrangement and suppress unfavorable agglomeration. Pronounced face-on orientation and enhanced structural coherence of 2PACz within the polymer matrix are evidenced. The templated ordering improves vertical charge transport, interfacial homogeneity, and film morphology. In binary OSCs based on PM6:BTP-eC9, the hybrid hole transport layers (HTLs) yield a champion power conversion efficiency (PCE) of 20.26%, with an open-circuit voltage (VOC) of 0.874 V, a short-circuit current (JSC) of 28.97 mA cm-2, and a fill factor (FF) of 80.02%. Devices incorporating hybrid HTLs exhibit exceptional operational stability, retaining over 90% of initial PCE (T90) after 405 h of continuous operation at the maximum power point (MPP). This work establishes polymer-directed SAM assembly as a scalable route to simultaneously optimize nanoscale molecular packing, interfacial energetics, and long-term device stability for high-performance OSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4472-0
Dynamic electrocardiography (ECG) monitoring during physical activity remains compromised by motion artifacts that corrupt signal fidelity, particularly with conventional gel electrodes whose impedance rises sharply under deformation. This work presents a thumb-sized liquid metal system integrating gallium-based epidermal electrodes with a self-adhesive elastomeric matrix to sustain robust ECG acquisition against motion. The electrodes exploit the fluidic compliance of eutectic gallium–indium to maintain continuous skin contact, while the adhesive formulation ensures stable interfacial coupling without additional fixation. The system achieves low motion artifact levels, preserving waveform morphology and R-peak detectability during ambulation. The compact form factor enables unobtrusive wearability, and the materials architecture addresses the trade-off between adhesion and conformability that limits existing dry electrodes. The study establishes a materials and device pathway for clinical-grade dynamic ECG in ambulatory and point-of-care settings, with implications for continuous cardiac monitoring where patient movement is unavoidable.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4464-9
Topological polarization textures have transitioned from theoretical predictions to experimental observations over two decades, yet their stabilization has remained largely confined to low-dimensional architectures where geometric confinement balances depolarization, strain, and gradient energies. Extending these textures into bulk ferroelectrics and quantitatively linking them to macroscopic electromechanical properties constitutes a persistent challenge. Wu et al. address this by engineering vortex and antivortex domains in bulk rhombohedral 0.7Pb(Mg1/3Nb2/3)O3-0.3PbTiO3 (PMN-30PT) crystals. Phase-field simulations reveal that increasing vortex core density from 6 to 27 μm⁻² enhances the dielectric constant (ε33/ε0) and piezoelectric coefficient (d33) by approximately 3.5-fold and 3.4-fold, respectively, correlating with increased polarization curl. Experimentally, a mechanically assisted direct-current poling (MDCP) strategy elevates vortex core density from 0.01 to 21 μm⁻², boosting d33 from 1380 to 1820 pC·N⁻¹ and ε33/ε0 from 4,630 to 6,230. This mechanically driven approach enables controllable manipulation of topological domain architectures in bulk crystals without nanoscale confinement, offering a scalable route for functional optimization. The work establishes bulk ferroelectrics as a platform for topology-mediated electromechanical design, introducing an additional degree of freedom for enhancing piezoelectric performance in three-dimensional crystals.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4320-4
Colloidal lead halide perovskite quantum dots (Pe-QDs) have achieved external quantum efficiencies exceeding 20% in red, green, and blue light-emitting diodes (LEDs), yet their integration into high-resolution displays is impeded by two persistent bottlenecks: the intrinsic ionic lability of Pe-QDs, which compromises structural and environmental stability, and the absence of mild, high-fidelity patterning techniques that avoid ligand detachment and surface defect formation. This work addresses both obstacles through a dual strategy. First, a ligand-fluoride co-stabilization method yields shape-defined, colloidally stable rhombic dodecahedral CsPbBr3 Pe-QDs; subsequent fluorine surface reconstruction using tetrabutylammonium fluoride (TBAF) enhances ligand binding affinity, producing BHOA+F CsPbBr3 Pe-QDs with a photoluminescent quantum yield (PLQY) of 94.6%. Accelerated ageing, ultraviolet irradiation, and thermal cycling tests confirm improved structural and environmental stability. Second, capillary liquid-bridge confined assembly enables reproducible, scalable fabrication of pixelated Pe-QDs with in-plane long-range order, vertical confinement, and precise spatial patterning. The resulting pixelated Pe-QDs LEDs exhibit high efficiency, sufficient brightness, and long operational stability, with the approach generalizable across red, green, and blue Pe-QDs for wide color gamut displays. This combination of surface fluorination and liquid-bridge assembly represents a landmark achievement in high-resolution display technology.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4505-9
Transition metal hydroxides are promising oxygen evolution reaction (OER) catalysts for alkaline water electrolysis. This study reports Ce-doped Co(OH)2 electrocatalysts synthesized via one-step electrodeposition, where the Ce3+/Ce4+ ratio is precisely controlled by deposition temperature. The optimized Ce-Co(OH)2 catalyst, obtained at 40°C, exhibits an overpotential of 236 mV at 10 mA cm-2 and maintains stability for 200 h. In an anion-exchange membrane water electrolyzer (AEMWE), the Ce-Co(OH)2 anode achieves a cell voltage of 2.04 V at 1 A cm-2 and operates for over 500 h at 500 mA cm-2. Mechanistic analysis reveals that Ce3+/Ce4+ dynamic electron buffering regulates surface reconstruction: during OER, electron transfer direction reverses (Ce → O → Co), with Ce donating electrons to Co sites to prevent over-oxidation and structural collapse. This work establishes a versatile strategy for balancing surface reconstruction and structural stability in Co-based OER catalysts, providing a foundation for designing high-performance, durable alkaline water oxidation electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4467-x
Conventional eye-movement interaction systems depend on video capture, infrared tracking, and image recognition, which impose inherent constraints on accuracy, response latency, and stability. This study introduces an eyelash-guided signal interaction system based on a triboelectric nanogenerator (PF-TENG) using PDMS-FDTS thin films. The system employs eyelash movements as interactive inputs, eliminating the need for complex optical acquisition devices. A CNN-LSTM hybrid neural network classifies distinct eyelash movement patterns with a classification accuracy exceeding 98.5%. The PF-TENG device exhibits ultra-flexibility and transparency, enabling seamless integration onto eyeglasses without obstructing the user's field of view. Experimental validation demonstrates real-time monitoring of ocular states for driving fatigue detection, accurately identifying fatigue signs and enhancing application potential in intelligent driving. The system offers a natural, comfortable input modality and significant advantages for human-machine interaction, with broad prospects in eye-movement control and intelligent transportation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4383-8
Conventional cancer therapies remain constrained by undruggable oncogenic proteins and acquired resistance. Proteolysis targeting chimeras (PROTACs) have emerged as a transformative modality that harnesses the ubiquitin-proteasome system to selectively degrade target proteins, offering advantages over traditional small-molecule inhibitors. However, clinical translation of PROTACs is impeded by intrinsic physicochemical limitations: high molecular weight, poor bioavailability, and lack of tumor-specific delivery. Integrating PROTACs with nanotechnology has yielded advanced nano-PROTACs platforms. Nanocarriers enhance solubility and stability, optimize pharmacokinetics, and enable spatiotemporally controlled drug release through passive or active targeting. This review systematically summarizes recent advances in engineering multifunctional nano-PROTACs for cancer therapy, with particular emphasis on design strategies by which nanoengineering enhances PROTAC performance. We evaluate how these platforms improve anticancer efficacy and minimize systemic toxicity while exploring their therapeutic potential in monotherapy and synergistic treatment settings. Finally, we discuss current challenges and future perspectives, providing a theoretical and technical foundation for next-generation nano-PROTACs as a precise and potent strategy in precision oncology.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4498-7
Two-dimensional porphyrin-based hypercrosslinked polymers (TPP-HCPs) were synthesized via room-temperature interfacial polymerization using 5,10,15,20-tetraphenylporphyrin and 1,3,5-trioxane. The resulting TPP-HCPs exhibited a BET surface area of 548 m2 g-1 and a CO2 uptake of 7.97 wt% at 1 bar and 298 K. CuO/TPP-HCPs nanospheres were fabricated by thermal conversion of Cu(NO3)2·3H2O in DMF at 135 °C, using TPP-HCPs as dynamic templates. This in-situ strategy generated CuO nanoparticles within the conjugated porous matrix, facilitating electron transfer and enhancing CO2 access to catalytic centers. In CO2 electroreduction, the composite achieved a total gas Faradaic efficiency exceeding 90% at ~500 mA cm-2 (-1.4 V vs. RHE), with 40.9% for C2H4, 8.2% for CH4, 31.9% for CO, and 12.3% for H2. The catalyst maintained stability over 24 h in an H-cell. These results demonstrate that 2D conjugated polymer-templated catalysts can sustain high-rate CO2 conversion to value-added products, offering a viable route for industrial CO2 utilization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4405-9
Conventional metal-halide X-ray scintillators, including Bi4Ge3O12 (BGO), Cs(Na)I:Tl, and Lu1.8Y0.2SiO5:Ce (LYSO), suffer from hygroscopic decomposition, high-temperature fabrication, and mechanical rigidity, which restrict their deployment in harsh-environment radiography. This study reports a nontoxic zero-dimensional organic–inorganic hybrid copper(I) halide, Cu2I2(C26H36NP)2 (Compound G), synthesized via a room-temperature solution route. The bulky phosphine ligands confer exceptional superhydrophobicity, with the material retaining 91.95% of its initial luminescence after 30 days of water immersion. A flexible scintillator screen fabricated from styrene-ethylene-butene-styrene (SEBS) exhibits a light yield of ~32,500 photons MeV-1, a spatial resolution of 19.14 lp mm-1, and a detection limit of 0.8 μGyair s-1. The screen enables stable X-ray imaging under flexible, high-temperature, and underwater conditions, eliminating vignetting and distortion in nonplanar objects. These metrics demonstrate that the superhydrophobic copper(I) halide scintillator addresses the water-stability bottleneck of commercial scintillators while delivering competitive light output and resolution, offering a viable pathway for medical diagnosis, nondestructive inspection, security checking, and space exploration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4432-9
Sodium vanadium phosphate (Na3V2(PO4)3, NVP) with NASICON structure is a promising cathode for sodium-ion batteries but suffers from low electronic conductivity and a high energy barrier for the V4+/V5+ redox couple, limiting practical energy density. A medium-entropy tuning strategy yields the multi-element substituted Na3.2V1.5Cr0.1Fe0.1Mn0.1Ni0.1Ti0.1(PO4)3 (ME-NVP). Entropy modulation tailors the microscopic electronic structure, enabling reversible V4+/V5+ redox at 4.0 V. Analyses reveal a synergistic diffusion mechanism that accelerates Na+ transport and enhances multiple-electron redox kinetics. Ex-situ X-ray diffraction confirms highly reversible structural evolution during cycling. The ME-NVP cathode delivers 116.8 mAh g-1 at 0.1C and retains 83.9% of initial capacity after 1000 cycles at 20C, with excellent performance from -12 to 50 °C. This work demonstrates that configurational entropy regulation unlocks high-energy polyanion cathodes for advanced sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4476-1
Self-sustained oscillation in soft actuators enables autonomous, untethered robotic locomotion, yet existing light-driven systems suffer from low oscillation frequencies, rapid photothermal degradation, and reliance on external controllers. This work presents a bat-inspired soft robot that converts continuous near-infrared (NIR) irradiation into sustained rotational motion via a coiled MXene-based liquid crystal elastomer (LCE) actuator. The actuator integrates Ti3C2Tx MXene nanosheets as photothermal converters within an LCE matrix, achieving a photothermal conversion efficiency of 78.3% and a steady-state temperature of 142 °C under 1.5 W cm−2 NIR (808 nm). The coil geometry induces a self-shadowing effect that generates periodic light exposure, producing autonomous oscillation at 2.7 Hz with an amplitude of 45°. The robot demonstrates a rotational speed of 120 rpm and a specific power density of 3.2 W kg−1, outperforming previously reported light-driven oscillators by a factor of 2.5. Under continuous operation for 10,000 cycles, the actuator retains 92% of its initial oscillation amplitude, with a degradation rate of 0.008% per cycle. The bat-inspired wing morphology enables directional rotation and obstacle avoidance in confined spaces. This platform eliminates the need for external modulation, offering a scalable route to autonomous soft robotics for inspection, environmental monitoring, and micro-manipulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4321-x
Poly(ethylene oxide) (PEO)-based solid polymer electrolytes are leading candidates for solid-state lithium metal batteries due to their flexibility, processability, and interfacial compliance. However, the strong crystallization tendency of PEO and limited lithium salt dissociation result in low ionic conductivity and low Li+ transference number, exacerbating concentration polarization and interfacial instability. Introducing metal-organic framework (MOF) fillers into PEO matrices has emerged as an effective route to regulate polymer-chain packing and promote salt dissociation via Lewis acid-base interactions. Yet, most studies focus on cubic ZIF-8, whose saturated Zn coordination environment limits intrinsic Lewis acidity and restricts its ability to immobilize TFSI- anions. Simultaneously, simple physical blending often leaves discontinuous interfacial transport regions in composite electrolytes, so improved salt dissociation does not automatically translate into fast Li+ transport. Here we report a PEO-based composite polymer electrolyte, denoted as PZS, that couples monoclinic ZIF-8 (M-ZIF-8) nanosheets with a thin SiO2 layer. The design combines two complementary functions: the under-coordinated Zn sites in M-ZIF-8 provide strong Lewis acid centers to adsorb TFSI- and promote LiTFSI dissociation, while the hydroxyl-rich SiO2 shell improves compatibility with the PEO matrix and helps construct continuous interfacial Li+ transport pathways. Benefiting from this synergy, the optimized PZS electrolyte delivers an ionic conductivity of 8.3 × 10-4 S cm-1 and a Li+ transference number of 0.57 at 60 ℃, together with an electrochemical stability window of 5.2 V. Li||Li symmetric cells remain stable for over 1200 h at 0.1 mA cm-2, and LFP||Li full cells retain 80% of their capacity after 400 cycles at 0.5 C.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4473-9
Selective ion separation is critical for resource recovery, water treatment, lithium extraction from salt lakes, and nuclear waste management, yet the differences in size, solvation structure, and coordination behavior among ions are often minimal, and separation is further complicated by valence, interfacial charge, and competing ions. Nanoporous materials with tunable sub-nanometer channels and chemically active interfaces can regulate ion entry, solvation reorganization, interfacial partitioning, intrapore migration, and release. This review examines three mechanistic categories—size and solvation sieving, chemical recognition, and dynamic gating—from the perspective of confined transport and ion–pore interactions, and compares their roles and coupling in systems of monovalent–monovalent, divalent–divalent, heterovalent, and chemically similar multivalent ions. We further distinguish selective adsorption, membrane enrichment, and transmembrane transport, and discuss how selectivity definitions, ion flux, feed composition, driving force, and operating time affect performance evaluation. Current research faces three major challenges: lack of comparability of performance data across different test conditions, insufficient direct evidence of ion solvation, site occupancy, and migration under operating conditions, and the complexity of feed streams. By adopting a sequential ion transport process as a unified conceptual framework, this review systematically compares separation mechanisms across diverse nanoporous materials, including MOFs, COFs, zeolites, 2D materials, microporous polymer membranes, ion-exchange membranes, biomimetic nanochannels, organic–inorganic composites, functionalized porous carbons, and biochars. This transport-process-oriented framework provides a general and mechanistic perspective for understanding and comparing selective ion separation across diverse nanoporous platforms.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4494-9
Superionic conductors exhibit high cation mobility arising from weak binding and continuous transport pathways, atomistically characterized by extensive structural disorder and partial occupancy akin to amorphization. This disorder, whether confined to a cation sublattice or extended to full amorphization, strongly impedes lattice thermal transport, rendering these materials intrinsically ideal thermal insulators. This work investigates Ag26I18W4O16, a superionic conductor tunable from fully amorphous to single-crystalline states, as a model system to probe the impact of disorder and amorphization on thermal transport. Extensive Ag+ disorder, in both crystalline and amorphous phases, reduces thermal conductivity to approximately the theoretical lower bound of 0.16 W/m-K with virtually no temperature dependence, while concurrently achieving the lowest mean sound velocity ever recorded for a dense solid. Pair distribution function (PDF) analysis of synchrotron X-ray total scattering data indicates that short-range disorder (< 5 Å), rather than long-range periodicity, governs thermal insulation performance in both phases. These findings suggest a design strategy reconciling structural stability with glass-like thermal insulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4309-8
Iridium-doped cobalt oxide nanosheets derived from a ZIF template were evaluated as oxygen evolution reaction (OER) catalysts for proton exchange membrane water electrolysis (PEMWE). Residual carbon was removed via a post-synthetic treatment to isolate intrinsic catalytic behavior. The Ir0.23Co0.77Ox catalyst exhibited enhanced activity and durability relative to commercial IrO2 in a practical PEMWE device. Potential-dependent, stage-resolved characterization combined with theoretical calculations probed catalyst stability under different operating voltages, revealing degradation mechanisms tied to applied potential. Contact angle measurements showed that the Ir0.23Co0.77Ox membrane electrode assembly (MEA) had water and air contact angles of 126° and 143°, respectively, compared to 126° and 143° for an IrO2 MEA at identical Ir loading, indicating improved wettability and gas release behavior. The work provides a framework for understanding potential-dependent stability in acidic OER catalysts and demonstrates a viable route to reduce Ir loading while maintaining PEMWE performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4324-4
Magnesium-oxygen (Mg-O2) batteries offer high theoretical energy density and low-cost earth-abundant magnesium, yet practical deployment has been impeded by poor cycling stability and low energy efficiency, primarily due to the sluggish decomposition of conventional MgOx discharge products. Here we demonstrate that trace water in the electrolyte redirects the cathodic reaction to form chemically reactive Mg2(OH)3Cl·4H2O as the main discharge product, enabling a new reversible pathway: 8Mg2+ + 4Cl- + 3O2 + 22H2O ⇋ 4Mg2(OH)3Cl·4H2O. This water-mediated chemistry significantly enhances redox reversibility compared with the MgOx route. The resulting Mg-O2 battery delivers over 324 stable cycles at 1000 mA·g-1 with a capacity of 500 mAh·g-1 and an energy efficiency of 92%, surpassing all previously reported Mg-O2 systems. The electrolyte comprises 0.25 M magnesium bis(trifluoromethanesulfonyl)imide (Mg(TFSI)2) and 0.5 M magnesium chloride (MgCl2) in ethylene glycol dimethyl ether (DME) with a trace amount of water. These findings establish a general strategy for reversible Mg-O2 electrochemistry and provide a new design paradigm for practical magnesium-based energy storage.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4165-1
Developing efficient photocatalysts for hydrogen peroxide (H2O2) synthesis is vital for sustainable chemistry, yet optimizing the electronic structure of triazine-based covalent organic frameworks (COFs) through precise spatial engineering remains a challenge. In this work, we constructed four model COFs to systematically decode how the spatial arrangement and incorporation level of triazine moieties regulate the electronic structures and H2O2 production efficiency. Combined experimental and theoretical analyses revealed that FB-AT achieved an optimal donor-acceptor architecture via rational spatial arrangement of triazine and benzene moieties. This configuration established an intramolecular potential gradient, which not only promoted charge separation by suppressing the exciton binding energy but also enriched the electron density at triazine sites. These electron-rich active centers significantly facilitated the oxygen reduction reaction by lowering the thermodynamic energy barrier for *OOH intermediate formation. Consequently, FB-AT exhibited a remarkable H2O2 production rate of 11055 μmol g-1 h-1 in pure water, along with a superior solar-to-chemical conversion efficiency of 1.16%. Additionally, FB-AT enabled complete degradation of phenol, tetracycline, and rhodamine B within 5–15 min of visible light irradiation. This work provides crucial guidance for the rational design of advanced COF photocatalysts for sustainable H2O2 production and water decontamination.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4295-5
Carbon nanomaterials (CNMs), including carbon nanotubes, graphene, and fullerenes, exhibit exceptional promise in precision biomedicine due to their tunable biocompatibility, programmable surface chemistry, large specific surface area, and quantum confinement effects. However, their clinical translation is hindered by aggregation, poor physiological dispersibility, and limited targeting specificity. This review systematically elaborates on surface engineering strategies—covalent functionalization, non-covalent assembly, and heteroatom doping—to optimize the multifunctionality, biocompatibility, and targeting capabilities of CNMs at the nano-bio interface. We explore how engineered interfaces enable advanced applications in biosensing, stimuli-responsive drug delivery, multimodal bioimaging, antibacterial therapy, and regenerative tissue engineering. The review also addresses challenges such as scalability, long-term toxicity, and regulatory hurdles, and proposes future directions to expedite clinical adoption. By providing a comprehensive framework for rational surface design, this work aims to bridge the gap between fundamental materials science and clinical needs, offering a roadmap for developing next-generation carbon-based theranostics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4271-5
Photocatalytic functional coatings are at a pivotal juncture where the primary research focus must transition from intrinsic material activity to a unified framework centered on surface serviceability. Surface serviceability encompasses the ability of a coating to maintain catalytic activity, interfacial integrity, multifunctional performance, safety, and manufacturability under specific service environments over its operational lifetime. Over the past three decades, photocatalytic surfaces have demonstrated potential for degrading organic pollutants, maintaining surface cleanliness, and enabling air purification, with applications in buildings, glass, highways, and infrastructure. However, high intrinsic activity alone does not guarantee stable long-term performance when the photocatalyst is immobilized as a substrate-integrated film. Performance is governed by coupled factors including interfacial adhesion, film structure, environmental aging, and functional durability. Current challenges extend beyond catalytic activity to include long-term deactivation, coating-substrate interfacial stability, trade-offs among multiple functions, adequacy of evaluation methods, and scalability of fabrication. These issues form a progressive service chain: design determines catalyst exposure and adhesion; environmental stresses induce functional or structural failure; multifunctional integration may compromise one function for another. Therefore, application-oriented evaluation is essential. This perspective advocates for a paradigm shift toward service-oriented design, requiring establishment of service-relevant evaluation protocols and development of scalable, repairable fabrication routes. Such efforts will enable photocatalytic coatings to evolve from high-activity laboratory materials into engineering surfaces that are verifiable, comparable, manufacturable, and durable in real-world applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4269-4
Self-assembled molecular interlayers (SAMs) are promising hole-selective contacts for high-efficiency organic solar cells (OSCs) due to their well-defined energy alignment and minimal parasitic absorption. However, their intrinsically limited mechanical robustness often leads to structural degradation and performance loss under mechanical deformation, restricting their application in flexible devices. Here, we report a nanoparticle-reinforced self-assembled composite interface that simultaneously enhances mechanical reliability and optoelectronic performance. Uniformly dispersed SiO2 nanoparticles are introduced as high-modulus reinforcing building blocks without disturbing molecular self-assembly. In contrast to NiOx nanoparticles, which suffer from aggregation and parasitic absorption, SiO2 nanoparticles exhibit excellent dispersion and optical transparency, enabling formation of a structurally compatible hybrid interface. Mechanistic studies reveal that SiO2 nanoparticles redistribute interfacial stress and form dynamic hydrogen-bond networks with phosphonic acid groups of 2PACz, providing efficient energy dissipation during cyclic deformation. Meanwhile, modulation of interfacial polarity extends the crystallization time window of the active layer, resulting in enhanced molecular ordering and improved charge transport. As a result, devices based on the SiO2/2PACz composite interface achieve a power conversion efficiency of 20.14% for rigid devices and 19.30% for flexible devices, placing the flexible devices among the highest-performing flexible OSCs reported to date, while retaining over 90% of their initial efficiency after repeated bending cycles. This work establishes a general strategy for overcoming the trade-off between electronic selectivity and mechanical robustness in ultrathin self-assembled molecular interfaces, providing design insights for high-performance flexible organic optoelectronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4300-3
The power conversion efficiency (PCE) of organic solar cells (OSCs) has surpassed 21% with the donor polymer D18, yet its processing from non-halogenated solvents like ortho-xylene (o-XY) remains inefficient due to uncontrolled film formation kinetics. Here, we systematically synthesize D18 polymers with molecular weights ranging from 41.6 kDa to 70.9 kDa to modulate crystallization kinetics. In-situ film drying studies reveal that lower molecular weights accelerate solidification, leading to excessive aggregation, while higher molecular weights slow it, causing insufficient phase separation. A medium molecular weight (D18-M) achieves a balanced crystallization rate, promoting favorable morphology and yielding a PCE of 20.55% with L8-BO as acceptor—one of the highest reported for non-halogenated solvent-processed OSCs. Energy loss analysis indicates that although low-molecular-weight polymers exhibit higher intrinsic luminescence, the blend film's emission is governed by exciton environment, which is dictated by morphology. This work underscores the critical role of molecular weight in controlling film formation and morphology, offering a simple yet effective strategy for high-efficiency, environmentally friendly OSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4319-x
This erratum corrects an error in the Acknowledgments section of the original article 'Investigation on graphene growth by roll-to-roll chemical vapor deposition' published in Science China Materials, Vol. 65, Issue 4, page 1042, 2022. The authors regret that the funding number (No. (2021)105) for the Shenzhen Science and Technology Program was incorrectly used. The correct funding number is No. KQTD20200820113010022. The authors apologize for any inconvenience caused. This correction does not affect the scientific content, results, or conclusions of the original paper. The original research focused on the kinetics of graphene growth via roll-to-roll chemical vapor deposition (CVD), a scalable method for producing high-quality graphene films. The study addressed challenges in continuous manufacturing, such as uniformity, growth rate, and defect control, and provided insights into optimizing process parameters for industrial-scale production. The erratum ensures accurate attribution of funding sources, maintaining the integrity of the research record.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4246-5
Developing organic solar cells (OSCs) processable from green solvents without additives or post-treatments is essential for sustainable manufacturing, yet high power conversion efficiency (PCE) remains difficult due to limited morphology control. Herein, we develop a new electron-deficient building block, dithiazolo[4',5':3,4;5'',4'':5,6]benzo[1,2-d][1,2,3]triazole (DTzBT), which fuses benzo[d][1,2,3]triazole (BTA) with thiazole to leverage S/N-mediated non-covalent interactions, enhance planarity and lower the HOMO. To isolate side-chain effects, two DTzBT-based donors, namely PTzMe-F (N-methyl) and PTzEH-F (N-2-ethylhexyl), have been designed and synthesized. PTzMe-F exhibits poor solubility and miscibility with L8-BO, yielding 2.64% PCE (chloroform). PTzEH-F exhibits excellent processability and favorable morphology, delivering 17.61% PCE (chloroform) and 19.17% as-cast from toluene without any additive or post-treatments. In addition, the ternary LbL device based on PTzEH-F/L8-BO:PC71BM achieved an impressive efficiency of 20.27%. Comprehensive characterization indicates that 2-ethylhexyl side chains afford optimal solubility while preserving strong intermolecular interactions and favorable phase separation. DTzBT mitigates BTA’s HOMO-raising tendency via electron-withdrawing thiazole fusion, reconciling aggregation tunability with energy-level control. These results show that precise backbone and side-chain co-design enables green-solvent, additive-free processing for high-performance OSCs, advancing sustainable photovoltaic manufacturing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4250-0
Shape memory polymer (SMP)-based transfer printing offers a promising route for heterogeneous integration of flexible electronics, yet non-contact release reliability remains a critical bottleneck. This study systematically investigates the influence of pickup heating modes—localized versus global—on the release yield and energy-delivery mechanisms through combined experiments and finite element simulations. The localized heating mode concentrates strain energy at the interface, enabling controlled chip ejection with high yield, whereas global heating dissipates energy, leading to release failure. Quantitative analysis reveals that localized heating achieves a release yield of 100% under optimized conditions, compared to near-zero for global heating. The ejection velocity under localized heating is higher, which may induce chip bouncing on the receiver substrate, affecting transfer accuracy; however, this can be mitigated by adjusting release gap and laser parameters. The findings establish a theoretical framework for energy pathway design, providing guidelines for achieving high-yield, accurate non-contact release in laser-induced transfer printing. This work advances the practical application of SMP-based transfer printing for micro-LED displays and flexible electronics, addressing a key manufacturing bottleneck.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4354-9
This review systematically examines the synthesis-structure-property relationships of hybrid graphene and carbon fiber reinforced composites, encompassing polymer, metal, and ceramic matrix systems. The hybridization of graphene with carbon fibers addresses the intrinsic limitations of conventional composites, such as weak interfacial bonding and insufficient multifunctionality. The review consolidates recent advances in fabrication strategies, including electrophoretic deposition, layer-by-layer assembly, and precursor impregnation, which enable controlled graphene distribution and orientation. Critical analyses of mechanical, tribological, electrochemical, and anti-ablation properties reveal that graphene addition significantly enhances interfacial shear strength, thermal stability, and electrical conductivity. For instance, in copper matrix composites, the incorporation of reduced graphene oxide with short carbon fibers improves tribological performance, reducing wear rates under specific load conditions. In ceramic matrix composites, graphene-modified C/C-SiC composites exhibit superior anti-ablation resistance, with mass loss rates reduced by up to 30% at elevated temperatures. Furthermore, graphene-coated carbon fiber electrodes demonstrate high specific capacitance and cycling stability in energy storage applications. The review also addresses challenges such as dispersion uniformity, scalability, and cost-effectiveness, proposing future directions for industrial adoption. By providing a comprehensive framework, this work guides the design of next-generation hybrid composites tailored for aerospace, automotive, and energy storage sectors.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4373-2
Infrared stealth technology demands materials with simultaneously low infrared emissivity and robust environmental stability. Traditional coatings suffer from high emissivity or poor thermal stability. Here, we report Sr-doped SmCoO3 perovskite ceramics achieving a record-low room-temperature infrared emissivity of 0.12 in the 8–14 μm atmospheric window. Systematic doping (x = 0, 0.1, 0.2, 0.3, 0.4, 0.5) via solid-phase synthesis reveals that Sr substitution induces a Co3+/Co4+ mixed valence state, increases oxygen vacancy concentration, and distorts the lattice. First-principles calculations (CASTEP) confirm that doping narrows the bandgap from 1.8 eV to 0.9 eV and enhances the double-exchange interaction, boosting carrier concentration and mobility. The optimized composition (x = 0.3) exhibits an electrical conductivity of 1.2×10^3 S/cm and a carrier density of 3.5×10^21 cm^-3, leading to strong infrared reflection. The material maintains emissivity below 0.15 after 100 hours of thermal cycling at 300°C and 500 hours of humidity exposure (85°C/85% RH), demonstrating exceptional environmental durability. This work establishes a new paradigm for designing high-performance inorganic infrared stealth materials via electronic-structural synergy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4342-3
Electron acceptors containing single-bond-linked building blocks offer attractive advantages for organic solar cells owing to their synthetic simplicity and structural modularity. However, achieving backbone planarity without compromising electronic compatibility remains a persistent challenge. Conventional conformational locking strategies based on alkoxy substitution can effectively suppress torsional freedom but often elevate the highest occupied molecular orbital energy level, limiting compatibility with widely used donor polymers. Here, we report a partially fused electron acceptor design that achieves intrinsic backbone planarity through heterocycle selection rather than side-chain-assisted conformational locking. By incorporating a benzodifuran core and furan-thiophene linkages, the resulting acceptors exhibit a near-coplanar backbone geometry as revealed by density functional theory calculations, without the need for electronically perturbing alkoxy groups. Devices based on the optimized acceptor (BDF-1) deliver a binary power conversion efficiency of 12.2%, and further improvement to 19.5% is achieved in a ternary blend with PM6 and BTP-eC9. The enhanced performance is accompanied by favorable morphology, balanced charge transport, and suppressed recombination losses. This work provides molecular-level insight into partially fused acceptor design and demonstrates that heteroatom-guided conformational locking offers a viable strategy for expanding the design space of acceptors with single-bond-linked building blocks while maintaining compatibility with mainstream donor systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4381-5
Bismuth telluride (Bi2Te3)-based alloys remain the benchmark for low-temperature thermoelectric applications, yet their conversion efficiency is limited by the trade-off between electrical and thermal transport. This study introduces a pseudo grain boundary engineering strategy to simultaneously enhance the average figure of merit (ZT) in p-type (Bi,Sb)2Te3 (BST) materials. By incorporating Ag-based compounds, the carrier concentration is optimized via substitution of Ag+ ions, while the introduction of secondary phases at grain boundaries effectively suppresses lattice thermal conductivity. The approach yields a peak ZT of 1.35 at 393 K and an average ZT of 1.25 across 303–483 K, representing a significant improvement over pristine BST. Compared to prior reports, this work achieves superior average ZT while maintaining high electrical conductivity, addressing the longstanding bottleneck of thermal conductivity reduction without compromising carrier mobility. The findings underscore the efficacy of pseudo grain boundary engineering in advancing Bi2Te3-based thermoelectrics for solid-state cooling and power generation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4292-4
The vast compositional space of high-entropy materials presents a fundamental challenge for catalyst discovery. Considering 21 candidate elements at a 1% atomic resolution, this combinatorial explosion exceeds 10 billion (>10^10) possibilities, rendering direct experimental exploration impractical. Furthermore, purely data-driven approaches often struggle to comprehend the intrinsic chemical roles of discrete elemental identities, yet they excel at mapping continuous concentration gradients. Recognizing this distinction, we transform this combinatorial explosion into a targeted optimization problem by decoupling elemental selection from compositional ratio refinement. Ultrafast carbon thermal shock (CTS) is first employed to screen viable elemental combinations and establish an optimal quinary framework. Machine learning (ML) is subsequently applied to optimize compositional ratios within this reduced space, where statistical modeling efficiently navigates the remaining high-dimensional landscape. Targeting the oxygen evolution reaction (OER) as a proof-of-concept, our hybrid framework pruned the search space from over 10^10 possible compositions down into 13 systems, ultimately identifying high-entropy oxide (HEO)-Fe17.57Co28.45Ni31.27Mo10.57Zr12.14 as the optimal catalyst. The optimized high-entropy oxide exhibits an overpotential of 240 mV at 10 mA cm−2 and sustains stable operation at 1 A cm−2 for over 600 h in 1 M KOH. Mechanistic analysis reveals that Mo electronically tunes oxygen-intermediate adsorption, while Zr enhances structural robustness, collectively enabling high activity and durability. This work demonstrates that bridging discrete physical screening with continuous data-driven optimization provides an efficient and generalizable pathway for navigating high-dimensional material frontiers.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4205-8
The global energy crisis and environmental pollution necessitate efficient recovery and utilization of thermal energy resources such as industrial waste heat. Thermoelectric materials, enabling direct conversion between thermal and electrical energy, offer broad application prospects in waste heat power generation and chip cooling. The energy conversion efficiency is determined by the dimensionless figure of merit, ZT = (S^2σ/κ)T, where S is the Seebeck coefficient, σ is the electrical conductivity, κ is the thermal conductivity, and T is the absolute temperature. Ideal thermoelectric materials require both a high power factor (PF = S^2σ) and low thermal conductivity. However, the strong coupling between electrical and thermal transport parameters makes synergistic optimization challenging. Over the past two decades, strategies such as band engineering, nanostructuring, liquid-like ions, interstitial atoms, phonon softening, and defect engineering have been explored. Among these, entropy engineering has emerged as a novel strategy that achieves synergistic optimization by introducing multiple components to increase configurational entropy. High entropy materials, originating from alloys, are defined as multi-principal element systems with five or more elements in near-equiatomic ratios forming single-phase solid solutions. The molar configurational entropy ΔS_conf = R∑x_i ln x_i, with materials classified as high entropy (ΔS_conf > 1.5R), medium entropy (1R < ΔS_conf < 1.5R), or low entropy (ΔS_conf < 1R). Four core effects are summarized: high entropy effect, lattice distortion effect, sluggish diffusion effect, and cocktail effect. Research has expanded from alloys to oxides, chalcogenides, and half-Heusler compounds. This review systematically summarizes the mechanisms by which lattice distortion in high entropy materials affects electrical and thermal transport, and discusses optimization strategies for thermoelectric performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4262-7
The escalating demands of artificial intelligence, machine learning, and neural computing necessitate multifunctional optoelectronic devices capable of integrating sensing, memory, and processing. Two-dimensional van der Waals heterostructures (vdWHs) offer unique advantages, yet their practical deployment is hindered by complex architectures and inefficient mode-switching. Here, we demonstrate a MoTe2/SnS2 anti-ambipolar heterojunction device enabling single-gate reconfiguration among frequency doubling, broadband photodetection, and neuromorphic computing. The device exhibits a peak-to-valley ratio (PVR) of 465, ensuring efficient frequency doubling. As a photodetector, it operates across an exceptionally broad spectral range of 520–2200 nm, with outstanding responsivity and detectivity. Furthermore, the device emulates complete synaptic behaviors, including short-term plasticity (STP), long-term plasticity (LTP), and paired-pulse facilitation (PPF). Integrated into a reservoir computing (RC) system trained on a vehicle motion dataset, it achieves a directional recognition accuracy of 98.7%. This work establishes a paradigm for multifunctional integration and low-power neuromorphic computing, advancing next-generation intelligent optoelectronic systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4206-6
Precise patterning of highly ordered organic semiconductor (OSC) thin-film arrays is critical for next-generation electronics. We report a ladder-like polysilsesquioxane (LPSQ) strategy to synthesize two functional analogs with tunable surface energies and robust dielectric properties. These LPSQ dielectrics, functionalized with alkyl or fluoroalkyl side chains, serve dual roles as gate insulators and patterning layers to guide blade-coating of 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT). This approach yields highly aligned arrays suitable for three-dimensional integration in flexible electronics. Synergistic combination of dense LPSQ dielectric packing and aligned semiconductor domains leads to excellent organic thin-film transistor (OTFT) performance, achieving approximately four-fold improvement in field-effect mobility compared to conventional silicon oxide dielectrics. Patterned LPSQ dielectrics enable high-resolution C8-BTBT patterning on plastic substrates, supporting 4-inch-scale 3D integration of flexible logic circuits, including inverters (voltage gain >100), NOR gates, and NAND gates. This work provides a scalable route to high-performance, large-area flexible organic circuits.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4315-2
High-temperature X-ray imaging demands scintillators with high crystallinity, efficient scintillation, and robust thermal stability, yet suitable materials remain scarce. Here, we report an ultra-high-crystallinity transparent glass-ceramic (GC) scintillator strategically designed via controllable heat-treatment-induced crystallization. A sequential precipitation method is employed, where cubic CaF2 nanocrystals initially form, subsequently promoting heterogeneous nucleation and growth of hexagonal BaAl2Si2O8. Intrinsic nanoscale phase separation into F-rich and O-rich domains significantly reduces atomic diffusion distances, yielding an unprecedented crystallinity of up to 97.6%. Notably, defect traps (oxygen vacancy defects, likely located within the lattice or at crystalline/amorphous interfaces) enable efficient carrier capture and thermally stimulated release, contributing to remarkable resistance to thermal quenching. Consequently, the GC scintillator maintains 90.6% of its integrated X-ray excited luminescence (XEL) intensity at 300 °C, with the integrated XEL intensity reaching 94.2% of commercial Bi4Ge3O12 (BGO) at room temperature. This enables stable high-temperature X-ray imaging with a spatial resolution of ~10.4 lp mm−1 up to 225 °C. This work provides a versatile pathway for developing high-sensitivity scintillators for extreme-environment X-ray imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4235-6
Fluorite-structured oxides (HfO2, ZrO2) are promising for resistive random-access memory (RRAM) due to their scalability and tunable properties. However, achieving high resistive switching on/off ratios remains challenging. Here, we report a collaborative strategy combining Hf/Zr ratio optimization and Lu3+ doping to regulate band structure and oxygen vacancy concentration in Hf0.4Zr0.6O2 (LHZO) thin films. The resulting LHZO devices exhibit a resistive switching ratio of 8.4 × 10^4, two orders of magnitude higher than that of ZrO2 (1.2 × 10^3). Electrical characterization and synchrotron radiation photoemission spectroscopy reveal that Lu doping widens the bandgap to 4.95 eV, downshifts the valence band, and introduces defect states, collectively suppressing p-type conductivity and reducing off-state leakage current. Simultaneously, Lu3+ doping enriches oxygen vacancies, stabilizing ohmic conductive filaments in the on-state. This co-optimization of band structure and oxygen vacancies effectively enhances insulating properties in the high-resistance state and ohmic conductivity in the low-resistance state, leading to superior resistive switching performance with robust retention (>10^4 s). Our findings establish a fundamental strategy for tailoring electronic properties of doped HfZrO2 thin films toward high-performance RRAM applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4113-3
Constructing abundant grain boundary defects is a promising strategy for developing high-efficiency catalysts. However, achieving dense grain boundary defects in CuO and Cu at the nanoscale remains challenging. Inspired by Turing patterns in nature, a Turing-type CuO catalyst (TGB-CuO) with abundant grain boundaries at ~10 nm nanoscale was prepared by annealing a dodecyl sulfate-intercalated basic copper carbonate. The balanced diffusion-reaction dynamics during pyrolysis drove the spontaneous formation of Turing-type grain boundary architectures in TGB-CuO. The resulting TGB-CuO electrode exhibited outstanding performance in electrochemical CO2 reduction (ECO2RR), delivering a Faradaic efficiency of 80.15% toward multi-carbon (C2+) products and maintaining over 50% ethylene selectivity at 300 mA cm−2 for 30 h of continuous operation. Activity investigations indicated that the metallic Cu retaining Turing-type grain boundary features (TGB-Cu) formed during electroreduction was responsible for the enhanced ECO2RR performance. The Cu(100)/(100), Cu(100)/(111), and Cu(111)/(111) grain boundaries promoted CO2 activation and *CO adsorption, while lowering the free energy barriers for the rate-determining *CO2− → *COOH step and C–C coupling step. This bioinspired reaction-diffusion strategy offers a new paradigm for creating high-density grain boundary defects, offering a general route toward efficient catalyst design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4277-1
Two-dimensional (2D) magnetic materials hold promise for next-generation spintronics, yet most exhibit Curie temperatures (Tc) far below room temperature, limiting practical applications. Here, we report the realization of room-temperature ferromagnetism in CuCrSe2 nanosheets via controlled anion removal achieved by post-synthetic vacuum annealing. Raw CuCrSe2 shows a low Tc of ~120 K, whereas annealed CuCrSe2 (A-CuCrSe2) nanosheets exhibit robust ferromagnetic ordering above 300 K. Structural and compositional analyses, including transmission electron microscopy, Raman spectroscopy, and X-ray absorption spectroscopy, confirm that A-CuCrSe2 retains the original layered crystal structure with an estimated Se vacancy concentration of approximately 10%. Magnetic measurements reveal room-temperature ferromagnetism in exfoliated nanosheets, corroborated by magnetic imaging and electric transport measurements. Anomalous Hall effect (AHE) measurements uncover the coexistence of two ferromagnetic phases within the same sample: one with low Tc (~120 K) and another with high Tc (>300 K), indicating spatially heterogeneous magnetic ordering driven by anion removal distribution. Density functional theory (DFT) calculations elucidate the microscopic mechanism, suggesting that Se vacancies modulate the magnetic exchange interactions, enhancing Tc. This work demonstrates that anion modulation is an effective intrinsic strategy to achieve room-temperature ferromagnetism in 2D materials, potentially advancing spintronic applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4234-3
The pursuit of high-energy-density sodium-ion batteries (SIBs) necessitates the development of stable high-capacity anodes. While amorphous carbon is a promising anode candidate for SIBs, its practical application is hindered by limited capacity. Herein, we design a composite anode by chemically confining a high-content (~25 wt%) short-chain sulfur into hierarchical porous hard carbon microspheres (SHHC) derived from microbe yeast. The SHHC anode exhibits a high reversible capacity of ~807 mAh g−1 at 0.03 A g−1 (~3 times that of conventional amorphous carbon) along with superior rate capability, and extraordinary long-term cyclability (almost 100% capacity retention after 2000 cycles at 1.0 A g−1). The high-content sulfur species contribute to superb redox reactivity for high-capacity sodium storage via a surface-dominated storage mechanism. The carbon matrix features an enlarged interlayer distance, which facilitates Na-ion intercalation and deintercalation for high-rate capability. Furthermore, the hierarchical porous structure with built-in cavities facilitates the Na-ion transfer and effectively accommodates the electrode’s volume expansion, achieving fast electrode kinetics and outstanding cyclability. Such a combination of favored properties leads to state-of-the-art comprehensive battery performance for Na-ion storage. Our finding envisions a new perspective on building stable high-capacity anode materials for SIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4192-y
Electrochemical water splitting is pivotal for scalable green hydrogen production, yet its practical deployment hinges on cost-effective electrocatalysts with high activity and durability. This study introduces a low-cost, three-dimensional (3D) nanoporous ZrVFeCoNi material fabricated via chemical dealloying, at merely 0.16% of the cost of Pt. The structure-activity relationship between its microstructure and hydrogen evolution reaction (HER) performance was systematically explored. Lattice defect effects from multiphase intermetallic compounds, combined with multi-metal synergy, optimize H+ adsorption energy and electron transfer kinetics. The 3D nanoporous architecture provides a high electrochemical surface area with abundant active sites, enhancing electrolyte penetration and reducing interfacial mass transfer resistance. Consequently, the ZrVFeCoNi electrode exhibits outstanding HER performance, requiring only a 38 mV overpotential to reach 10 mA cm−2 and maintaining stable operation for 1000 h at 500 mA cm−2. Integrated into a full water electrolyzer (ZrVFeCoNi || IrO2/Ni), the system achieves a cell voltage of 1.60 V at a current density of 400 mA cm−2. Advanced characterization and density functional theory (DFT) calculations reveal that interfacial interactions and charge transfer at heterointerfaces drive catalytic activity, showcasing the potential of 3D nano-structured multiphase intermetallic compounds as high-performance electrocatalysts for green hydrogen systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4179-x
Perylene diimide (PDI) radical anions exhibit poor environmental stability, restricting their generation efficiency and practical application. Here, a PDI-functionalized bispillar[5]arene (PDI-P5) was designed to construct stable and high-efficiency photothermal radicals. Intramolecular charge transfer (ICT) between PDI and bispillar[5]arene narrows the energy gap. Under 455 nm ultraviolet light irradiation and diethylamine (DEA) vapor exposure, photoinduced electron transfer (PET) efficiently generates PDI-P5·− radicals, which possess broad near-infrared (NIR) absorption, enhanced non-radiative transitions, and excellent stability. Notably, PDI-P5·− can rapidly reach 90 °C under 0.20 W cm−2 simulated sunlight irradiation. Moreover, it exhibits superior multi-step photothermal anti-counterfeiting performance. This work provides a novel strategy for the development of stable radical-based photothermal materials, which holds great potential for anti-counterfeiting and bioimaging applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4112-6
Radiostrontium remediation is crucial for ecological protection and sustainable development of nuclear energy. However, efficient removal of 90Sr from complex radioactive liquid waste, especially under acidic conditions, remains challenging due to material instability and intense proton competition. Herein, the rapid and highly selective capture of Sr2+ in neutral and even acidic solutions has been achieved by a layered potassium phosphatoantimonate KSbP2O8 with excellent radiation and thermal stability. Under neutral conditions, it possesses high maximum adsorption capacity (qmSr = 110.25 mg g−1), rapid adsorption kinetics (the removal rate (RSr) of 91.54% within 30 min), and excellent selectivity for Sr2+, and facile regeneration. Particularly, even under acidic conditions (pH 2.0), KSbP2O8 still maintains excellent Sr2+ removal capacity (qmSr = 79.38 mg g−1), fast kinetics, and high selectivity. A mechanism study by multiple characterizations reveals that the efficient Sr2+ removal of KSbP2O8 mainly stems from ion exchange between Sr2+ and interlayer K+ in KSbP2O8, which is attributed to the synergy between the Sb5+-induced Brønsted acidity and the high charge density of the anionic framework. This study demonstrates the exceptional capability of phosphatoantimonates to selectively capture Sr2+ under acidic conditions, highlighting the potential of phosphatoantimonates as effective scavengers for radiostrontium remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4207-0
Self-assembled monolayers (SAMs) are critical for optimizing electrode interfaces in organic solar cells (OSCs), as their molecular conformation and ordering govern interfacial quality. Conventional carbazole-based SAMs (e.g., 2PACz) rely on flexible alkyl linkers whose conformational freedom often results in disordered packing, incomplete coverage, and limited environmental robustness, especially under air processing. Here, we design and systematically study a series of well-defined carbazole SAM homologues (Cz-PPA, Cz-HPA, PCz-HPA, and PCz-PPA) to elucidate the role of synergistic conformational locking achieved through linker rigidification and terminal conjugation extension. PCz-HPA, which integrates a rigid cyclohexane linker with a strongly conjugated 3,6-diphenylcarbazole end group, enables effective conformational locking. It forms a highly ordered, densely packed monolayer on ITO, delivering high surface coverage, a strengthened interfacial dipole, and improved energy-level alignment. The rigid framework and ordered interface enhance air-process stability and interfacial contact, thereby suppressing recombination and facilitating exciton dissociation and charge collection. Using PCz-HPA as SAM for the devices based on PM6:L8-BO reaches 19.75% efficiency and it demonstrates consistent gains across multiple systems. These results identify conformational locking via linker rigidification as a general design rule for durable, high-performance SAM interlayers in organic optoelectronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4293-9
Traditional soft magnetic alloys (SMAs) suffer from a performance trade-off where enhancing magnetic properties often compromises mechanical and other properties, limiting their use in high-efficiency power systems and advanced electronics. The design concept of medium- and high-entropy alloys (M/HEAs) offers a pathway to overcome this limitation. By leveraging multi-principal-element compositions and tailorable microstructures, medium- and high-entropy soft magnetic alloys (M/HE-SMAs) can integrate superior soft magnetic properties with exceptional mechanical strength-ductility synergy, high electrical resistivity, good thermal stability, and excellent corrosion resistance. This article reviews design strategies for synergistic enhancement of multiple properties in M/HE-SMAs, including blending multiple ferromagnetic and non-ferromagnetic elements into solid solution, inducing local chemical order, tailoring nanoprecipitates, controlling grain size, and engineering dual/multi-phase structures. The cooperative interactions among these strategies are discussed. Potential research directions for further development and practical applications are proposed.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4166-5
Oxygen evolution reaction (OER) represents a significant kinetic bottleneck in sustainable energy conversion due to its complex multi-step electron transfer process. Spin manipulation has recently emerged as a promising strategy to overcome traditional catalytic scaling relationships. However, the commonly used ferromagnetic materials or external magnetic fields suffer from practical limitations including material constraints and high energy consumption. The chiral-induced spin selectivity (CISS) effect in chiral inorganic nanomaterials with high stability, conductivity, and exceptional chiroptical properties offers a groundbreaking alternative by enabling spin polarization without the need for external magnetic fields. This review systematically examines the application of chiral inorganic nanomaterials for improving OER efficiency via the CISS effect. The fundamental principles of CISS and its influence on OER kinetics are discussed. Recent experimental advances highlighting the enhanced catalytic performance are analyzed. Future research directions and challenges in leveraging chirality and spin as key design principles for next-generation OER electrocatalysts are highlighted.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3696-3
The development of substitutable meniscus implants that can effectively protect articular cartilage remains a great challenge. Herein, a polyurethane with chemical crosslinking and sulfobetaine extenders containing hydrophobic chains (PU-CL-hSB) is developed, which could improve comprehensive properties and long-term stability simultaneously. By regulating the mole ratio of functional groups, PU-CL-hSB with appropriate mechanical properties, excellent tribological properties, and good fatigue resistance is used to prepare substitutable meniscus implant by hot-pressing. Due to the synergistic effect of functional groups, PU-CL-hSB meniscus implant presents comparable or even superior properties to native meniscus. It withstands a maximum force of 26.08 N versus 25.14 N for native meniscus, an energy dissipation from 45.93 to 39.17 N mm compared to 28.83 to 19.11 N mm for native meniscus over 300 cycles, and a friction coefficient from 0.08 to 0.19 compared to 0.11 to 0.26 for native meniscus. This PU-CL-hSB meniscus implant is further implanted into live rabbit knee joints for 8 and 25 weeks by a new approach, and in vivo data indicate that PU-CL-hSB meniscus implant not only protects articular cartilage from severe damage without eliciting inflammatory responses, but also can maintain normal physiological activities in the native state. Our findings present a substitutable meniscus implant that could be applied in vivo and propose evaluation methodologies for meniscus implants.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4197-4
Deep-blue organic light-emitting diodes (OLEDs) remain the most challenging primary-color emitters due to stringent exciton energy requirements. We strategically designed two innovative deep-blue emitters, SCZ-4AnCN and STPA-4AnCN, via systematic functionalization of an anthracene core with arylamino-decorated spirofluorene donors and cyano-substituted phenyl acceptors. Comprehensive theoretical and experimental analyses demonstrate that these spirofluorene-anthracene hybrids adopt precisely engineered distorted configurations, effectively suppressing detrimental intermolecular π–π stacking in condensed phases. The sp3-hybridized bridgehead carbons in spirofluorene units play a pivotal role by simultaneously restricting π-conjugation extension and fine-tuning donor–acceptor interactions, thereby stabilizing the lowest excited singlet (S1) state with dominant local excitation (LE) character. This molecular engineering yields exceptional deep-blue emission with remarkable efficiency. Notably, the materials exhibit unique high-lying reverse intersystem crossing (hRISC) behavior, enabling efficient triplet harvesting. Optimized doped devices incorporating SCZ-4AnCN achieve outstanding performance, including a maximum external quantum efficiency (EQE_max) exceeding 10% and CIE coordinates (0.154, 0.052) approaching the BT.2020 blue standard. Nondoped devices maintain impressive performance with an EQE_max of 7.51% and superior operational stability, demonstrating less than 10% efficiency roll-off at 1000 cd m−2. This work validates anthracene-based molecular architectures for deep-blue electroluminescence and establishes a transformative design paradigm for next-generation OLED emitters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4213-x
Lipid peroxyl radicals (ROO·) are terminal propagating species in lipid peroxidation, driving oxidative damage in neurological disorders. Their prolonged lifetime and rapid diffusion within lipid membranes render them difficult to neutralize. Here, we report a bioelectric-responsive TEMPO-doped polydopamine (PDA@TEMPO) nanozyme that sustains catalytic interception of ROO· radicals under persistent oxidative stress. By coupling a PDA redox reservoir with TEMPO catalytic centers, the nanozyme establishes a self-regenerating radical-neutralization cycle via proton-coupled electron transfer (PCET). The π-conjugated framework facilitates charge migration and enables an electric-field-enhanced antioxidant response. In a seizure model, the nanozyme dynamically responds to bioelectric fluctuations, accelerating radical interception and alleviating oxidative stress in neural microenvironments. These findings establish bioelectric-coupled nanozymes as a general strategy for catalytic and sustained regulation of oxidative stress in neural microenvironments, providing a potential therapeutic approach for neurological disorders.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4199-8
High-entropy borides (HEBs) represent an emerging class of high-entropy materials that have garnered significant attention as ultra-high-temperature ceramics (UHTCs). By leveraging the high configuration entropy effect, HEBs stabilize single-phase solid solutions, exhibiting a suite of properties unattainable in traditional binary borides. This review systematically consolidates research progress on HEBs, beginning with theoretical predictions and component design via first-principles methods. It then details typical HEB systems and principal synthesis techniques, including arc melting and spark plasma sintering. The core analysis evaluates the outstanding performance of HEBs, emphasizing exceptional mechanical properties such as ultra-high hardness and excellent fracture toughness, alongside high-temperature friction and wear behavior, and oxidation resistance. Finally, the review outlines application prospects in extreme environments like aerospace and cutting tools, while also addressing current challenges. The paper underscores the potential of HEBs to overcome the hardness-toughness trade-off inherent in conventional ceramics, driven by strong metal-boron hybridization. This comprehensive overview positions HEBs as promising candidates for next-generation thermal and mechanical protection systems, with future research directions focusing on optimizing compositions and processing to tailor properties for specific applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4217-y
Rational design and construction of effective photocatalysts is a promising way for green and sustainable chemistry, but still a great challenge. Herein, taking triphenylamine-containing aldehydes as reactants, two covalent triazine frameworks (CTFs), tris(4-formylphenyl)amine (TPA)-CTF and tris(4-formylbiphenyl)amine (TBPA)-CTF, were rationally constructed. The strong electron donor property of the triphenylamine moieties derived from the initial reactants and the strong electron acceptor nature of the in-situ formed built-in triazine rings in CTFs endowed these robust triphenylamine-based CTFs with donor-acceptor (D-A) or donor-π-acceptor (D-π-A) structure features. Photocatalytic experiments revealed that, compared with the controlled phenyl analogue CTF, 1,3,5-tri(p-formylphenyl)benzene (TFPB)-CTF, both of the triphenylamine-based CTFs exhibited superior photocatalytic activity not only in photocatalytic hydrogen peroxide generation, but also in photocatalytic aerobic oxidations of diverse organic substrates. Theoretical studies further confirmed that their enhanced photocatalytic performance should be attributed to their unique D-A or D-π-A features in the constructed triphenylamine-based CTFs. This work successfully demonstrated that rational selection of reactants containing electron donor moieties to construct CTFs should be a reliable way for the construction of effective photocatalysts for photocatalytic oxidation reactions.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3691-9
Near-infrared (NIR) spectroscopy has significantly advanced NIR light sources, yet creating NIR emitters with optimal luminescence properties, high thermal stability, and adjustable emission peaks remains a critical challenge for future smart NIR devices. Here, we introduce a chemical unit cosubstitution strategy by incorporating Ca2+ and Sn4+ ions into the garnet structure. Through this approach, Y3−yCayGa4.95−ySnyO12:0.05Cr3+ (y = 0–1) phosphors were developed by modulating the A&C ligands, resulting in emission centers ranging from 708 to 768 nm. The modified local environment of Cr3+ accounts for the increased light intensity (2.71 times) and broadening observed. Furthermore, this study investigated the impact of varying Cr3+ concentrations (Y2.6Ca0.4Ga4.6−xSn0.4O12:xCr3+) on the production of high-performance phosphors. Compared with Y3Ga4.93O12:0.07Cr3+, the optimized phosphor exhibited exceptional external quantum efficiency (EQE = 34.96%). The luminescence enhancement is attributed to an increase in radiative transitions caused by octahedral Jahn-Teller distortion, whereas the notable thermal stability (91.3% at 423 K) is attributed to the presence of weak electron-phonon coupling (EPC) and oxygen vacancy (OV) defects. Finally, by combining it with a 450 nm blue LED chip, we constructed a near-infrared phosphor-converted LED (NIR pc-LED) device with superior electroluminescence efficiency (18.8% @ 100 mA), increasing the ultralow quenching rate (< 5% intensity loss after 30 days of operation) and demonstrating remarkable performance in plant lighting applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3629-3
Electrically pumped lasers with reduced physical dimensions are critical for future optical information processing, storage, and photonic integrated circuits. However, electrical injection in perovskite lasers faces challenges including material instability, non-radiative losses, and Joule heating. Here, we demonstrate an ultralow-threshold perovskite microlaser decorated with gold nanoparticles (AuNPs), enabling simultaneous optical pumping and current injection at ambient temperature. The lasing threshold is reduced to 8.6 μJ/cm², approximately 44% lower than that of pristine devices (15.3 μJ/cm²). The AuNPs, with optimized size, enhance both lasing performance and electrical properties, achieving a current injection density of 2.98 kA/cm². AuNPs accelerate hot-carrier cooling, reducing non-radiative recombination and mitigating Joule heating. The threshold decreases progressively with increasing electrical assist fraction. Stability tests confirm excellent resistance to aging and humidity, with stable lasing output under co-excitation in ambient air. This work underscores the feasibility of electrically driven perovskite microlasers, offering a pathway toward electrically pumped microlaser diodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3579-8
Metal sulfides such as CdS are promising for solar-driven H2O2 production but suffer from rapid charge recombination and severe photocorrosion. This study introduces a dual-functional strategy synergizing sulfur vacancy (Sv) engineering and polydopamine (PDA) coating to overcome these limitations. Sv-CdS nanorods were hydrothermally synthesized with tunable vacancy concentrations, followed by in-situ PDA deposition to construct a direct Z-scheme heterojunction. X-ray photoelectron spectroscopy (XPS) and density functional theory (DFT) calculations reveal that the introduction of S vacancies reduces the work function of CdS, facilitating energy level alignment with PDA and enabling efficient electron transfer from CdS to PDA. By tuning the concentration of S vacancies, the charge transfer efficiency can be maximized. As a result, the photocatalytic H2O2 production rate reaches 2539.5 μmol g−1 h−1 under visible light, and further increases to 4395.5 μmol g−1 h−1 after PDA encapsulation—15.6 times higher than that of pristine CdS. Concurrently, PDA enhances O2 adsorption and protects Sv-CdS from photocorrosion. Sv-CdS@PDA exhibited superior photostability compared to Sv-CdS after three consecutive photocatalytic cycles. Mechanistic studies suggest that the Z-scheme heterojunction effectively separates electron-hole pairs: electrons in the conduction band of CdS reduce O2 to ·O2−, which is subsequently converted to H2O2, while holes in the valence band of Sv-CdS oxidize water to replenish O2. This work provides fundamental insights into engineering charge transfer and stability in sulfide-based photocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3803-8
The molecular copolymerization of donor-acceptor (D-A) interactions has been effectively utilized to modulate the charge transfer dynamics in polymeric carbon nitride (PCN) photocatalysts. Herein, a D-A configured photocatalyst (TPCN) was constructed by copolymerizing 4,4’,4’’-(1,3,5-triazine-2,4,6-triyl) trianiline (TAPT) as the electron donor with triazine units (electron acceptor). The unique propeller structure of TAPT, combined with the triazine framework, expanded the π-conjugated system and induced a strong built-in electric field (BIEF) across the D-A configuration. Theoretical calculations and transient absorption spectroscopy revealed that this synergistic effect facilitated intramolecular charge separation and widened the range of light absorption, indicating accelerated charge transfer and suppressed recombination in TPCN. The optimized TPCN3 sample exhibited dramatically enhanced photocatalytic H2O2 production (1.74 mmol g−1 h−1), representing a 13.4-fold increase over pristine PCN. Additionally, the TPCN3 sample also exhibited significantly faster degradation kinetics than PCN counterpart toward various emerging contaminants. This work demonstrates a promising strategy for designing efficient metal-free photocatalysts for sustainable H2O2 production and environmental remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3564-9
Sluggish water dissociation kinetics in the alkaline hydrogen evolution reaction (HER) hamper its practical production. Here, a heterojunction electrocatalyst featuring Ru-Ni(OH)2 interfaces on nickel foam (NF) with self-engineered built-in electric fields (BIEF) was synthesized via a simple in situ galvanic replacement reaction. The hierarchical Ru-Ni(OH)2/NF exhibits a record overpotential of 9.6 mV at 10 mA cm−2 for alkaline HER, surpassing most reported catalysts and commercial Pt/C. It also shows exceptional activity for hydrazine oxidation reaction (HzOR) at 100 mA cm−2 with a remarkably low potential of ca. 0.015 V vs. RHE. The assembled overall hydrazine splitting (OHzS) system integrating HER and HzOR requires a cell voltage of about 0.09 V to reach 50 mA cm−2, which is 1.637 V lower than the corresponding overall water splitting (OWS) device. Systematic analysis and calculation reveal that the BIEF induces redistribution of interfacial electrons for Ru, facilitating H2O dissociation and intermediate conversion, delivering ultra-high electrocatalytic performance. This work provides an avenue for design and preparation of electric field-mediated catalysts towards sustainable energy conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3848-7
Conventional heterogeneous photocatalysts often suffer from insufficient light absorption, rapid charge recombination, and a lack of specific reactive sites for efficient photocatalytic oxidation. To overcome these limitations, we propose a molecular polarization engineering approach utilizing structurally well-defined donor (D)-acceptor (A) covalent triazine frameworks (CTFs). The construction of dipole-induced built-in electric fields within the D-A-structured CTFs enables enhanced exciton dissociation and facilitates directional charge transfer. Specifically, the asymmetric A1-D-A2 moiety enhances molecular polarization in the dual-acceptor system CTF-TBT (A1-D-A2), enabling efficient charge separation through multiple electron-withdrawing units. This structural design promotes directional electron transfer toward the secondary acceptor (benzothiazole, A2), while simultaneously concentrating holes on the donor unit. Consequently, the A2 moiety acts as a site for efficient O2 activation via electron accumulation, whereas the highly oxidized donor unit provides strongly positive holes (h+) that facilitate substrate oxidation. Experimental and DFT calculation results confirm that CTF-TBT demonstrates highly enhanced photocatalytic oxidation performance, which can be attributed to its multi-channel charge separation mechanism and spatially separated redox-active sites. This study highlights the effectiveness of molecular dipole engineering in designing heterogeneous photocatalysts with controlled charge transfer pathways and improved redox capabilities. The proposed design principles provide a universal approach for promoting solar-driven chemical synthesis applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3841-6
Ni-rich layered oxide cathodes are pivotal candidates for next-generation lithium-ion batteries (LIBs) due to their high capacity and energy density. However, their susceptibility to structural deterioration and interfacial degradation during cycling causes substantial capacity fade, hindering commercialization. This work proposes a synergistic strategy of lattice doping and in situ surface coating to enhance structural integrity and interfacial stability of LiNi0.9Co0.05Mn0.05O2. La and Y dopants act as pillars to reinforce the layered structure, mitigating volume changes and expanding c-axis spacing to facilitate Li+ diffusion. Concurrently, La4NiLiO8 and LiYO2 coatings protect the cathode from H2O/CO2 corrosion and electrolyte attack, while their high lithium-ion conductivity promotes Li+ transport. The modified cathode delivers exceptional electrochemical metrics: high specific capacity of 207.3 mA h g−1, remarkable cycling stability with 97.6% retention after 100 cycles, superior rate capability of 152.1 mA h g−1 at 10.0 C, and enhanced thermal stability. This work establishes a paradigm for multi-dimensional stabilization of Ni-rich cathodes via synergistic bulk and interface engineering, providing insights for designing high-performance energy storage systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3602-1
Solid-state lithium batteries (SSLBs) are promising next-generation energy storage systems due to their high safety and energy density. However, poor low-temperature performance of solid-state electrolytes remains a critical challenge. Here, we present a facile and scalable approach for synthesizing a low-temperature-resilient polymer electrolyte based on ethylene-vinyl acetate (EVA), leveraging its unique molecular structure for enhanced lithium-ion transport. The EVA polymer electrolyte (EPE) demonstrates a high ionic conductivity of 5.13×10−4 S cm−1 at room temperature and retains a remarkable conductivity of 2.72×10−5 S cm−1 at −40 °C. This superior performance is attributed to the synergistic interaction between the ester functional groups of EVA and lithium salts, which reduces the ion dissociation energy barrier and facilitates efficient ion migration. The EPE enables stable lithium plating/stripping cycling for over 3000 h at −40 °C and supports long-term cycling of LiFePO4-based full cells at −40 °C for over 900 cycles. This work highlights the potential of cost-effective, scalable EPEs for next-generation SSLBs, particularly in extreme environmental conditions.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3605-0
Nickel oxide (NiOx) is widely used as a hole transport material in inverted perovskite solar cells (PSCs). However, its practical application is limited by low intrinsic conductivity and insufficient hole extraction ability, leading to significant interfacial defects that reduce device efficiency and stability. To overcome these issues, two isomeric small organic molecules, 2,6-NOT and 1,5-NOT, were developed and introduced to modify NiOx. These isomers share the same structure but differ in the substitution positions of functional groups, resulting in distinct molecular planarity. Experimental results demonstrate that 1,5-NOT, featuring extended conjugation and enhanced planarity, more effectively enhances the hole extraction/transport capabilities and conductivity of NiOx compared to 2,6-NOT. The NiOx/1,5-NOT-based device achieves a remarkable power conversion efficiency (PCE) of 24.20%, along with excellent long-term stability, surpassing the NiOx control device (18.12%) and the 2,6-NOT-based device (21.87%). These findings indicate that modifying NiOx with small organic molecules significantly improves charge transport performance, and increasing molecular planarity is particularly beneficial for enhancing hole transport and reducing defect density, thereby increasing both efficiency and stability. This work provides a new strategy for NiOx modification via small organic molecules, offering a promising route to high-performance inverted PSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3559-5
Polyamide (PA) membranes are promising for lithium extraction from spent lithium-ion battery (LIB) leachate but face a trade-off between selectivity and permeability. Here, we demonstrate that nascent PA membranes post-grafted with triaminoguanidinium (TAG) monomers (PA-TAG membranes) gain expanded ion passage channels (0.8–7.1 Å) and enhanced positive charge, achieving high-performance lithium separation. The PA-TAG membrane exhibits a pure water permeance (PWP) of 15.5 L m−2 h−1 bar−1, superior divalent ion rejection (~98%), and an excellent separation factor (~30), significantly outperforming pristine PA membranes. In a simulated acidic battery leachate, the PA-TAG membrane achieved a relative volumetric lithium recovery rate of 48.2% after a two-stage nanofiltration process, with the Li+/M2+ mass ratio of the second permeate reaching 53.35, 445 times that of the feed (0.12). The membrane maintained stable performance over 45 hours of nanofiltration and resisted acidic conditions (pH=2) for at least 20 days. These results highlight the potential of PA-TAG membranes for efficient lithium extraction from acidic battery leachate, addressing the critical need for sustainable recycling of spent LIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3553-7
Gesture interaction has emerged as a highly effective interface for intelligent human-computer interaction, attributed to its intuitive interaction modality and multi-dimensional control capabilities. However, traditional gesture interaction devices often depend on predefined encoding rules, which substantially limit interaction efficiency and degrade user experience. This study introduces an innovative intelligent finger ring interaction system based on a triboelectric nanogenerator utilizing PDMS/SrTiO3 composite thin film (PS-TENG). The system maps freehand writing gestures directly to textual information input, thereby eliminating the need for complex gesture encoding schemes and offering a user-friendly, low-learning-curve input method. By integrating a deep learning model, the system achieves recognition accuracies of 98.21% for English letters, 96.87% for Arabic numerals, and 96.44% for Chinese characters. Furthermore, it supports secure and encrypted data transmission and enables wireless interaction for gaming control. These findings indicate that the intelligent finger ring interaction system possesses significant potential for practical applications in information input and wireless control.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61075-X
The proliferation of electronic devices has intensified electromagnetic radiation pollution, necessitating advanced microwave absorption materials. This study presents the electrospinning fabrication of FeNiCo/carbon nanofiber (FeNiCo/CNF) composites with exceptional microwave absorption properties. The FeNiCo/CNFs achieved a minimum reflection loss (RLmin) of −55.5 dB at 14.24 GHz with an ultrathin matching thickness of only 1.6 mm. Microstructural analysis and electromagnetic parameter testing revealed that the superior absorption stems from the synergistic interaction between the carbon nanofiber network and FeNiCo alloy nanoparticles, which promotes multiple reflections and efficient energy dissipation. The precise control of coercivity and permeability via systematic modulation of magnetic metal composition enabled enhanced impedance matching and optimized magnetic-dielectric synergy. Furthermore, radar cross-section (RCS) simulations confirmed the material's capability to significantly reduce RCS values across a wide angular range, validating its potential for stealth technology applications. This work introduces a cost-effective and sustainable approach for developing ultralight, high-performance microwave absorbers, addressing the limitations of conventional materials such as high density and poor stability.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(25)61033-X
Carbon-based materials have gained significant attention in anticancer treatment due to their exceptional biocompatibility, yet critical challenges persist in establishing definitive correlations between their porous structures and functional performance. We report the use of a silica template to guide pore formation in the design of mesoporous carbon spheres (mC) with tailored pore structures for improved combined photothermal-chemotherapy. The mesopore size of mC was adjusted by kinetic control of resin polymerization and silica hydrolysis. Structural characterization showed that 4.4 nm mesopores enabled an exceptional gemcitabine loading of 228 mg g−1 and a sustained pH/thermal dual-responsive release with >70% drug release under near-infrared (NIR) irradiation. Finite element analysis demonstrated pore size-dependent heat transfer dynamics, with the improved mC achieving a superior photothermal conversion efficiency of 62% by a combination of N-doping and defect engineering. In vitro evaluations confirmed outstanding biocompatibility with >95% cell viability at 200 μg mL−1 and potent tumor suppression in pancreatic and biliary cancer models with an ~5% cell viability at 25 μg mL−1 where combined therapy showed a 3.7-fold increased cytotoxicity over monotherapy. The improved structure of mC facilitated cascade therapeutic effects with enhanced tumor permeability derived from NIR-triggered hyperthermia and prolonged therapeutic exposure due to pH-responsive drug release. This pore engineering strategy establishes a structure-function process for next-generation theranostic platforms, addressing the critical limitations of conventional pancreatic and biliary cancer therapies through spatiotemporal control of multimodal treatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3755-8
Lead-free piezoelectric ceramics, including potassium sodium niobate (KNN), bismuth sodium titanate (BNT), and barium titanate, are promising alternatives to lead-based counterparts due to environmental regulations. However, their functional properties—piezoelectric coefficient, mechanical quality factor, dielectric loss, Curie temperature, and thermal stability—remain inferior. Oxygen vacancy engineering has emerged as a key strategy to optimize these properties via defect modulation. Oxygen vacancies, prevalent point defects, arise from high-temperature processing, non-stoichiometry, volatile oxide evaporation, or reducing atmospheres. Acceptor doping and post-processing annealing further increase their concentration. These defects influence electrical conduction, piezoelectric/dielectric behavior, and catalytic activity. They exist as lattice vacancies, domain wall vacancies, grain boundary vacancies, and defect dipoles with cation vacancies. Their presence induces lattice distortion, hinders domain wall motion, increases coercive field, and enhances mechanical quality factor via hardening. Defect dipoles align with spontaneous polarization, creating internal bias fields that pin domains, reducing losses. Quantification of oxygen vacancies remains challenging; concentrations below 1 at% in NBT and KNN are difficult to detect. Techniques like XPS have reliability issues. A combination of impedance spectroscopy, XPS/STEM, EPR/PAS is recommended. Defect chemistry modeling, using acceptor doping to fill vacancies, allows inference of non-stoichiometry ranges. For NBT, Bi deficiency of 0.0017–0.0033 and O deficiency of 0.0025–0.0050 were calculated, corresponding to Na0.5Bi0.4967–0.4983TiO3.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3677-9
The demand for high-performance scintillators in high-temperature applications, such as industrial flaw detection and oil exploration, necessitates materials with both high efficiency and thermal robustness. This work reports Tb3+-doped oxyfluoride glass scintillators exhibiting anti-thermal-quenching radioluminescence (RL). Three synergistic strategies were employed: (i) an oxyfluoride glass host providing a low-phonon-energy environment, (ii) increased structural densification of the glass network, and (iii) thermally enhanced energy transfer from Ce3+ to Tb3+. The resulting scintillators achieve an optical transmittance exceeding 88% at 542 nm, a record RL intensity of 350% relative to a standard Bi4Ge3O12 (BGO) crystal, and an imaging resolution of 24 lp mm−1. Notably, the RL intensity at 633 K reaches 143% of its room-temperature (303 K) value, demonstrating significant anti-thermal-quenching behavior. In contrast, commercial BGO and CsI:Tl scintillators exhibit RL intensities dropping to approximately 1% under identical conditions. These results establish the potential of Tb3+-doped glass scintillators for high-temperature X-ray imaging and provide a strategic framework for developing thermally robust scintillating materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3610-7
Electrochemical CO2 reduction reaction (CO2RR) offers an attractive route to produce value-added multicarbon (C2+) products, yet suffers from competing hydrogen evolution and monocarbon production. Here, we propose a dual-confinement effect on CO2 reactant and *CO intermediate, induced by tuning the pore configuration of reconstructed covalent organic frameworks (RC-COFs). The highly crystalline microporous RC-COF-1, when coated on a Cu electrode, enhances local CO2 concentration and restricts CO diffusion, thereby promoting C-C coupling. In acidic electrolyte, the RC-COF-1@Cu electrode achieves a maximum C2+ Faradaic efficiency (FE) of 67.0% at 500 mA cm−2, while maintaining a total carbon product FE above 90% across a broad current density range (100–500 mA cm−2). Experimental and theoretical analyses confirm that the ordered micropores of RC-COF-1 modulate reactant adsorption and intermediate diffusion, leading to improved C2+ selectivity. This work underscores the critical role of COF pore architecture in microenvironment engineering for heterogeneous catalysis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3647-4
Chromium oxides (CrOx) and fluorinated graphite (CFx) are two typical cathode materials for lithium primary batteries. The former possesses the highest theoretical energy density but suffers from low practical capacity and inferior rate capability; the latter has the highest theoretical discharge capacity but fails to support fast discharge. Combining the merits of both cathodes via a composite design is desirable, yet the electrochemical performance of such composites remains unsatisfactory. In this work, we identified that by regulating the overlapped discharge potential of these two cathodes, fluorine atoms migrate from CFx to CrOx, leading to a homogeneous distribution of LiF and improved ionic and electronic conductivity, ultimately enhancing high-rate discharge performance. Benefiting from this synergetic effect, the CrOx/10%eCFx composite exhibits a considerably high energy density of 496.59 Wh kg−1 at a power density of 49.7 kW kg−1 (50 C), far superior to pure CrOx and CFx electrodes. We believe that the high-performance CrOx/eCFx composite cathode will justify its practical application in revitalizing advanced lithium primary batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3630-2
This study demonstrates a dual-interface engineering approach for performance enhancement in perovskite-silicon tandem solar cells. By applying ethylenediamine dihydroiodide (EDAI2) to simultaneously modify both top and bottom interfaces of wide-bandgap perovskite layers, we achieve synergistic defect suppression and charge transport optimization. Time-resolved photoluminescence characterization reveals extended carrier lifetimes and improved spatial homogeneity in dual-modified perovskite films. The optimized single-junction wide-bandgap (>1.66 eV) perovskite solar cells attain a champion efficiency of 22.75% with enhanced operational stability. Implemented in perovskite-silicon tandem configuration, the devices achieve over 31% power conversion efficiency, validating the effectiveness of organic ligand-mediated dual-interface engineering in regulating carrier dynamics and advancing perovskite-based tandem photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3506-3
Metallic glasses (MGs) often suffer from sluggish hydrogen evolution reaction (HER) kinetics in neutral and alkaline media, with their catalytic performance predominantly confined to acidic environments. Herein, we reported a novel thermoplastic forming technique to fabricate a self-supported partially crystallized nanoporous Pt56.2Ni5.2Cu16.8P21.8 metallic glass (C-NPMG). The C-NPMG catalyst delivers ultralow overpotentials of 18.0 mV (0.5 M H2SO4), 42.2 mV (1 M KOH), and 88.0 mV (1 M phosphate-buffered saline (PBS)) at a current density of 10 mA cm−2, outperforming most state-of-the-art non-noble MGs and Pt-based benchmarks across all pH conditions. Notably, it maintains negligible performance decay for over 1000 h in alkaline electrolytes, showcasing superior stability. Experimental and computational analyses reveal that the enhanced HER activity arises from three synergistic effects: (1) the high-specific-surface-area nanoporous architecture that maximizes active site exposure; (2) the formation of crystallite-amorphous interfaces during partial crystallization, which lowers the energy barrier for H2 desorption; (3) the hierarchical super-hydrophilic and super-hydrophobic wettability of the C-NPMG, which optimizes mass transport and prevents electrolyte-induced corrosion. This work establishes a novel design paradigm for developing high-performance, pH-universal HER electrocatalysts by integrating structural nano-engineering and crystallite-amorphous phase synergy in metallic glass systems to overcome the trade-offs between performance and stability in electrochemical water splitting.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3695-8
Sulfur-based lithium-ion batteries, particularly those employing sulfurized poly(acrylonitrile) (SPAN) cathodes and graphite (Gr) anodes, offer high theoretical capacity and low cost but suffer from temperature-dependent capacity decay. This study systematically investigates the electrochemical dynamics and capacity decay mechanism of SPAN||Gr pouch cells cycled at 25–55 °C. Multiscale analyses reveal that capacity fade arises from active lithium loss and increased resistance, both accelerated by higher temperatures. Active lithium loss is primarily attributed to dead lithium formation and thickening of the solid electrolyte interphase (SEI) and cathode electrolyte interphase (CEI), while resistance increase is predominantly due to SEI/CEI thickening. As temperature rises, active lithium loss becomes the dominant decay factor. Leveraging the consistent decay mechanism across temperatures, an accelerated aging model based on the Arrhenius equation is developed: y = 0.9x + a. This model accurately predicts cycling parameters at specific temperatures and reduces testing time by 50% when extrapolating from 55 °C to 25 °C. These insights provide critical guidance for developing long-life sulfur-based batteries for practical energy storage applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3733-2
Irreversible sodium loss, primarily caused by solid electrolyte interphase (SEI) formation during initial cycling, significantly degrades the capacity of sodium-ion batteries by depleting active sodium. While pre-sodiation mitigates initial sodium loss, it fails to address continuous loss throughout the battery lifecycle. To overcome this limitation, we propose a sustained sodium compensation strategy utilizing activation-releasing systems. Key to this approach are high-capacity sodium compensators, Na2C2O4 and Na2C4O4, supported on a B and N co-doped Mo2C-W2C (MoW-C) heterostructure catalyst. This configuration enables efficient sodium release at charging voltages of 3.53 and 3.78 V, respectively. By integrating the sodium supplement agent onto the separator, and precisely controlling voltage and charge, multiple sodium replenishment is achieved over the entire battery lifecycle. This strategy reduces initial active sodium loss by 36.53%. Furthermore, a single activation during subsequent usage provides an additional 0.115 mAh cm−2 of active sodium. As a result, the cell exhibits exceptional cycling stability, with a capacity loss of only 0.059% per cycle over 350 cycles at 0.5 C.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3625-3
Zirconia (ZrO2)-based fluorite ferroelectric materials are promising for nonvolatile memory and logic devices due to their CMOS compatibility and cost advantages over hafnium oxide (HfO2). However, the metastable nature of the ferroelectric orthorhombic phase (o-phase) hinders practical application. Here, we report the strain-mediated stabilization of the ferroelectric o-phase in ZrO2 thin films grown on niobium-doped strontium titanate (NSTO) substrates with different crystallographic orientations via chemical solution deposition. Systematic structural and ferroelectric characterization, combined with simulation, reveals that substrate orientation controls in-plane tensile strain, selectively promoting epitaxial growth of the o-phase. The ZrO2 film on NSTO(110) exhibits the highest o-phase content, achieving a remanent polarization (2Pr) of 92.64 μC/cm², which remains as high as 88.54 μC/cm² after resistive-capacitive (RC) delay calibration. The device shows endurance of approximately 10^7 cycles with favorable fatigue characteristics. X-ray absorption spectroscopy (XAS) further indicates distortion of Zr-O tetrahedra, providing microscopic insight into the ferroelectricity. This work presents a novel strategy for property tuning of ZrO2 films and supports their application in storage and logic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3770-9
Intramolecular through-space charge-transfer (TSCT)-enabled thermally activated delayed fluorescence (TADF) emitters have shown exceptional potential for advancing organic light-emitting diode (OLED) technologies, owing to their efficient utilization of triplet excitons and optimized photophysical properties. To date, the intrinsic correlation among molecular geometries, intramolecular non-covalent interactions, and photophysical properties in TSCT-TADF emitters remains unconfirmed, and this study theoretically clarifies this critical correlation. Specifically, through integrating molecular engineering, screening strategies, first-principles calculations, energy decomposition analysis, and statistical modeling, we systematically investigated 24 experimentally reported TADF molecules, and 54 newly designed structures in both solution and thin-film environments. We establish a clear geometric criterion for high-efficiency TSCT-TADF emitters: donor-acceptor (D-A) dihedral angles below 25° and interfragment distances within 4 Å—conditions validated by both theoretical predictions and experimental evidence. Based on this insight, we designed two novel molecular libraries with benzene- or carbazole-derivative bridges, using O-bridged triphenylamine (DPXZ) as the donor and quinolino[3,2,1-de]acridine-5,9-dione (QAO) as the acceptor. Our calculations confirm that sub-25° D-A dihedral angles correlate with exceptional delayed fluorescence efficiency, with predictions reaching up to 96% and an average of 70% for the new thin film systems. This study provides a rational design strategy for high-performance TSCT-TADF emitters, significantly advancing the molecular-level understanding of through-space interactions and accelerating the discovery of tailored, efficient OLED materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3584-3
Sutures, as necessary medical devices for postoperative treatment, are no longer merely supportive but are required to have advanced functions to promote repair. Here, we report an absorbable self-powered electrical stimulation suture (SES-suture). The suture is composed entirely of absorbable materials (magnesium, polylactic acid, and polycaprolactone) and can be used in vivo for incision closure and repair. The suture has the capacity to generate spontaneous electrical stimulation in response to body movement, allowing for accelerated tissue reconstruction. An in vivo muscle incision repair model in rabbits demonstrated that the wound healing rate under treatment with this suture was 1.6 times faster than that of commercial sutures, proving its postoperative therapeutic capability. Immunofluorescence and quantitative analyses showed that SES-sutures significantly increased α-SMA and CD31 expression, with levels approximately 2.8 and 3.2 times higher than the blank group, respectively, indicating enhanced angiogenesis and muscle regeneration. The SES-suture exhibited excellent mechanical properties, sustained electrical output, structural and functional stability after implantation, and good biocompatibility. This large animal approach offers crucial translational evidence for potential human applications, addressing the limitations of rodent models due to differences in biomechanics and regeneration rates. While the biosafety profile requires further long-term evaluation, the findings strongly suggest that SES-sutures represent a promising therapeutic strategy for enhancing tissue regeneration and functional recovery.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3683-y
Effective management of traumatic hemorrhage requires rapid blood loss control and facile removal of hemostatic materials to minimize secondary tissue damage. We fabricated a strongly adhesive aerogel (OPA) via Schiff-base crosslinking of oxidized hyaluronic acid (OHA) and ε-polylysine (ε-PL), enabling rapid hemostasis in lethal arterial trauma and on-demand removal via phase transition. OPAs exhibited tunable porosity and rapid blood absorption. Surface hydroxyl, amino, and carboxyl groups promoted strong hydrogen bonding with tissues, blood cells, and plasma proteins, enhancing tissue adhesion and platelet capture/activation. In a rabbit femoral-artery-injury model, OPA4 shortened hemostatic time by ~80% and reduced blood loss to 38% of the blank group. Notably, OPAs retained only 2% of initial adhesion after hydration, allowing gentle removal. OPAs also demonstrated excellent antibacterial activity, biocompatibility, and biodegradability. The simple one-step freeze-drying process and tailorable shapes offer scalable production and versatile applications. This study provides a versatile strategy for emergency and surgical hemostasis, combining rapid control of life-threatening arterial bleeding with on-demand atraumatic removal, promising improved patient outcomes and streamlined postoperative care.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3669-1
Halide perovskite light-emitting diodes (PeLEDs) have advanced rapidly due to their high photoluminescence quantum yield, tunable bandgap, and color purity. However, conventional perovskites exhibit small exciton binding energies, which weaken radiative recombination and limit external quantum efficiency (EQE). Strong spatial confinement strategies, such as thin films, small grains, or quantum-confined structures, have boosted EQE beyond 20% but introduce Auger recombination and ion migration, causing efficiency roll-off and instability. This commentary highlights a novel approach by Xiao et al. (Nature, 2025) that employs weakly space-confined all-inorganic CsPbBr3 perovskites, synthesized using sacrificial additives hypophosphorous acid (HPA) and ammonium chloride (NH4Cl). This method yields highly oriented monocrystalline domains exceeding hundreds of nanometers with no observable grain boundaries, contrasting with control films (submicrometre grains with abundant boundaries) and strongly confined systems (~20 nm crystallites with organic ligands). The reduced grain boundaries lower defect density and block ion migration, while controlled crystallization suppresses vacancies and lattice distortions, enhancing carrier mobility and raising the ion migration energy barrier. The strategy achieves record-breaking performance and stability, addressing EQE roll-off and operational lifetime limitations. This approach offers a versatile framework for other all-inorganic perovskite systems, advancing PeLEDs toward practical high-brightness displays and lighting.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3764-5
Rechargeable lithium-ion batteries (LIBs) are ubiquitous in portable electronics and electric vehicles, yet their flammable liquid electrolytes pose safety hazards and limit energy density. All-solid-state batteries (ASSBs) with solid-state electrolytes (SSEs) offer enhanced safety and higher energy density. Among SSEs, metal chloride SSEs (Li aMCl b, M = In, Y, Er) combine high ionic conductivity, mechanical deformability, and compatibility with high-voltage cathodes. However, their ionic conductivity and anode stability require improvement. Here, we introduce pentavalent Ta5+ doping into Li3InCl6 (LIC) to engineer Li+ vacancies via charge compensation, yielding Li3−2xIn1−xTaxCl6 (LITxC, 0 ≤ x ≤ 0.6). Ta5+ incorporation efficiently increases Li+ vacancy content without disrupting the cubic close packing (ccp) structure. The optimized composition, Li2.4In0.7Ta0.3Cl6 (LIT0.3C), achieves an ionic conductivity of 2.19 mS cm−1 at 30 °C and a low activation energy of 0.273 eV, balancing vacancy concentration and Li+ content. Ta5+ doping also enhances kinetic stability against the anode. ASSBs with LIT0.3C demonstrate excellent cycling stability: Ni90 cathodes retain 72.3% capacity after 1000 cycles at 0.5 C, while NCM523 cathodes retain 84.1% after 500 cycles at 0.2 C and 80.7% after 1000 cycles. These results highlight a practical strategy for improving chloride SSE performance, offering new insights for high-performance ASSB design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3654-5
Hydrogen production by photosynthetic green algae is an efficient biological process that utilizes light energy to convert water and carbon dioxide into clean and renewable energy. In this paper, we constructed a hybrid system combining graphitic carbon nitride (g-C3N4) and Chlorella pyrenoidosa (Chlorella), in which g-C3N4 serves as an extracellular electron source and Chlorella acts as a biological reactor for specific hydrogen production. In particular, the electronic structure of carbon nitride was optimized by means of hydrothermal alkalization and copper ion doping, expanded the light absorption range and enhanced the light response ability. g-C3N4, as an extracellular electron source, can provide electrons for Chlorella to improve hydrogen production performance which is 3.7 times that of bare Chlorella. The construction of a biological hybrid system is a feasible optimization strategy for the hybrid system to promote the synergistic effect of the hybrid system by regulating the properties of non-living components.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3780-3
Real-time health monitoring and ongoing evaluation of physiological conditions are becoming increasingly vital for the advancement of future medical diagnostics and personalized healthcare solutions. Given that certain illnesses necessitate prompt and accessible detection methods, wearable chemical sensors have garnered considerable interest for their capability to monitor health through physiological signals and chemical indicators. This review delivers a thorough examination of recent developments in four primary categories of wearable chemical sensors: biosensors, humidity sensors, gas sensors, and ion sensors. We explore the representative materials, device structures, operating mechanisms, and various application scenarios for each type of sensor. By investigating the latest innovations in these technologies, we aim to provide a detailed overview of the current research landscape, highlight existing challenges, and present potential future directions of wearable chemical sensors in healthcare monitoring.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3757-2
β-Ga2O3 is a promising candidate for solar-blind ultraviolet photodetection owing to its suitable bandgap of approximately 4.9 eV, excellent photoresponse characteristics, and high stability. However, the lack of a sufficient driving force within the material leads to extensive bulk charge recombination, limiting its photocurrent and thus posing significant challenges in designing high-performance Ga2O3-based photodetection. In this study, we propose a gradient doping strategy to achieve a Sn-doping concentration gradient along the β-Ga2O3 film thickness. By combining sol–gel synthesis with rapid thermal annealing, a spatially graded band structure with a full-space built-in electric field is constructed, which increases the width of band bending over a large region and is crucial for significantly enhancing carrier separation and transport in the bulk. The resulting gradient Sn-doped β-Ga2O3 enables exceptional photoelectric performance without an external bias under 254 nm irradiation, including a superior responsivity of 66.88 mA W−1, a high detectivity of 8.12 × 10^11 Jones, and a fast rise/decay time of 79/65 ms, outstanding most existing similar reported photoelectrochemical (PEC) type optoelectronic devices. Additionally, the device exhibits excellent long-term stability and enables high-resolution underwater ultraviolet imaging. This study demonstrates that the gradient doping strategy provides a feasible approach for enhancing the PEC performance of β-Ga2O3 photoelectrodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3708-y
Polar two-dimensional (2D) perovskites, with their excellent semiconductor properties, intrinsic anisotropy, and bulk photovoltaic effect, have emerged as promising candidates for self-driven polarization-sensitive photodetectors. However, these self-driven polarized detectors typically require fabrication along the spontaneous polarization direction to maintain device operation in the self-driven mode, which imposes additional limitations. Herein, we demonstrate multidirectional self-driven polarization-sensitive photodetection by constructing 2D perovskite-based asymmetric contact devices, Ag/2D perovskite/C. The built-in electric field, originating from the difference in work functions, acts as the driving force for the separation and transport of photogenerated carriers. Notably, this approach does not necessitate a specific direction, thereby enabling multidirectional self-driven photodetection. Under excitation by linearly polarized light, our devices exhibit impressive polarization-sensitive discrimination in multiple directions, achieving polarization ratios of 3.3 and 3.1 along the a and b-axes, respectively. Our work enriches the approaches enabling self-driven polarization-sensitive photodetection, free from the previous limitations.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3697-8
Multi-site coupling is a promising strategy for developing highly efficient and CO-resistant hydrogen oxidation reaction (HOR) catalysts for proton exchange membrane fuel cells (PEMFCs). However, designing multifunctional synergistic schemes for single-atom sites remains a significant challenge. Herein, we propose a dual-template-confined oxophilic engineering strategy to construct well-dispersed iridium-nickel (IrNi) atomic dimers adjacent to IrNi nanoclusters on porous nitrogen-doped carbon (IrNi Dimer/NC1.8-PNC). The paired IrNi dimer features an asymmetric Ir-N3 configuration coordinated with heteroatomic Ni-N3O via an N-bridge. Remarkably, IrNi Dimer/NC1.8-PNC exhibits a ~23-fold enhancement in mass activity (4.36 A mg−1 Ir at 20 mV) and 5-fold longer stability compared to benchmarking Pt/C toward HOR, while achieving a high rated power density of 1.18 W cm−2 in PEMFC anode applications. Furthermore, IrNi Dimer/NC1.8-PNC demonstrates superior CO tolerance over monometallic Ir and Pt/C in both half-cell and full-cell devices. Combined experimental and density functional theory studies reveal that oxophilic Ni modulates the electronic environment of Ir through alloying and dimer interactions, thereby enhancing HOR activity. Importantly, the asymmetric IrNi dimer enables efficient CO* and OH* co-adsorption while facilitating CO2* desorption, synergistically mitigating CO poisoning and improving atom utilization efficiency. This work provides a design strategy and fundamental insights for multi-site synergistic catalysts in PEMFC anodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3693-0
The development of catalysts with highly efficient oxygen evolution performance and low-Ir loading is key to scaling up the application of proton exchange membrane (PEM) water electrolysis technology. Here, an Ir-skin catalyst (Ir@KM) is realized on a potassium-manganese oxide (K0.25MnOx (KM)) using an ion-exchange method. The Ir-skin over the prepared Ir@KM has a low Ir–Ir atomic distance, endowing an energetically favorable oxide path mechanism to allow a low theoretical overpotential of 0.13 V. Ir@KM offers a low overpotential of ~280 mV at a current density of 10 mA cm−2 and provides a high mass activity of up to 18,500 A gIr−1 at a cell voltage of 1.8 V in PEM, which is 17.6 times higher than that of IrO2, demonstrating a significant advantage in reducing the cost of the membrane electrode. The presented Ir-skin concept represents a promising strategy to fabricate low-Ir catalyst with high activity and durability for practical applications of PEM.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3702-0
Construction of metal-mediated redox sites is an appealing approach to enhance photocatalytic CO2 reduction coupled with H2O oxidation. However, conventional static redox sites generally lack spatiotemporal matching during reaction processes due to the constraints of rigid structure and the linear scaling relationship of adsorbed species. Herein, an alkanolamine-Ir synergistic system was developed, where flexible monoethanolamine (MEA) molecules function as molecular ferries to selectively adsorb CO2 via carbamate formation, while adjacent Ir nanoparticles (NPs) serve as H spillover hubs that relay protons, creating spatiotemporal adaptability that synchronizes CO2 reduction and water oxidation. In addition, time-resolved in situ spectroscopy directly captures the rapid transformation of carbamate intermediates concurrent with sustained IrOOH intermediates formation. Microkinetic modeling further demonstrates that the MEA-Ir modified system (M-Ir/ACN) creates interconnected H spillover networks between Ir NPs and MEA, facilitating efficient proton transport that drives *COOH formation with a favorable thermodynamic energy. As a result, the M-Ir/ACN achieves a 20-fold increase in CO production compared to the pristine sample while maintaining high stability throughout 45 h of continuous operation. This study presents that flexible molecular ferries boost CO2 adsorption, and deciphers how flexible molecular-metal synergy directs the trafficking of CO2-derived intermediates toward highly efficient CO2 photoreduction.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3762-9
The integration of interfacial photothermal conversion and hydrovoltaic effects into bifunctional evaporators offers a promising route to simultaneously address freshwater scarcity and energy demands. However, the development of low-cost bifunctional evaporators and elucidation of the underlying co-generation mechanism remain challenging. Here, we report a porous carbon derived from waste polyester via a metal-organic framework (MOF)-assisted carbonization strategy, which is subsequently fabricated into a bifunctional evaporator for freshwater and hydroelectricity co-generation. The porous carbon exhibits a high specific surface area of 904 m² g⁻¹, hierarchical micro- and mesopores, and abundant oxygen-containing groups. The resulting evaporator demonstrates broadband light absorption, localized thermal management, good hydrophilicity, and high flexibility. Under 1 sun illumination, it achieves an open-circuit voltage of 250 mV, a short-circuit current of 14 μA, and an evaporation rate of 2.34 kg m⁻² h⁻¹, ranking among the most efficient freshwater-hydroelectricity co-generators. The weakened hydrogen-bonding network reduces the water evaporation enthalpy to 1.7 kJ g⁻¹. Mechanistic studies, including molecular dynamics simulations, reveal that selective Na⁺ interaction induces differential ion migration rates, generating a streaming potential. Additionally, the photothermal effect enhances voltage output by promoting interfacial ion concentration gradients. Outdoor tests confirm stable voltage output of 250 mV and freshwater production of 2.34 kg m⁻². This work provides a scalable platform for fabricating advanced evaporators from waste plastics and unravels the co-generation mechanism, offering a sustainable strategy to mitigate freshwater and energy crises.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3685-7
NiMo-based catalysts are promising for the hydrogen evolution reaction (HER), yet optimizing their electronic structure and enhancing mass transfer remain challenging. Here, we report a route to synthesize two-dimensional (2D) porous Mo2N-Ni heterojunction nanosheets with tuned Ni/Mo ratio for enhanced alkaline HER. The precursor is assembled from polyoxometalate clusters (PMo12) and layered Ni(OH)2. The interaction between PMo12 and Ni(OH)2 suppresses particle agglomeration during pyrolysis, yielding 2D porous sheets composed of small Mo2N-Ni units. Electron transfer from Ni to Mo2N redistributes electrons at the heterojunction, optimizing intermediate adsorption/desorption. The porous structure enhances mass transfer, reducing catalyst impedance. The optimized catalyst exhibits an overpotential of 19 mV at 10 mA cm−2, comparable to commercial Pt/C. An anion exchange membrane (AEM) electrolyzer pairing this catalyst with NiFe-LDH achieves 500 mA cm−2 at 1.80 V and operates stably for 300 h. This assembly method offers a scalable strategy for efficient catalyst production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3785-5
The effective separation and utilization of photo-generated carriers are critical for advancing photocatalysis, particularly in coupled reactions of H2 production and value-added chemical synthesis. Here, a sandwich-structured MnO2@ZnIn2S4@Ti3C2 hollow sphere was designed, with MnO2 and Ti3C2 loaded on the inner and outer surfaces of ZnIn2S4, respectively. MnO2 acts as an oxidation cocatalyst collecting photo-generated holes, while Ti3C2 serves as a reduction cocatalyst for electrons, promoting spatial separation of carriers and enabling spatially separated redox reactions. The hollow structure enhances light harvesting. The optimal catalyst achieves photocatalytic H2 production rate of 6.29 mmol g−1 h−1 and benzaldehyde production rate of 5.26 mmol g−1 h−1 from benzyl alcohol oxidation, significantly outperforming ZnIn2S4, MnO2@ZnIn2S4, and ZnIn2S4@Ti3C2. In situ irradiated X-ray photoelectron spectroscopy confirms effective carrier separation. In situ electron paramagnetic resonance and diffuse reflectance infrared Fourier transform spectroscopy reveal reaction intermediates. This work provides a strategy for designing efficient photocatalysts for coupled H2 production and selective oxidation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3807-8
Electrocatalytic co-reduction of CO2 and nitrate offers a sustainable route for urea synthesis, valorizing nitrogenous waste and CO2. However, achieving high-performance urea electrosynthesis under ambient conditions remains challenging due to the need for simultaneous activation of CO2 and efficient H2O dissociation to supply active *H for *NOx hydrogenation, ultimately forming key C- and N-containing intermediates for C–N coupling. Here, we report a bifunctional Pd-single-atom-modified Cu (Pd1Cu) nanorod catalyst that synergistically promotes adsorption and stepwise activation of CO2 and H2O, steering the reaction pathway toward selective urea synthesis. Integrating experimental evidence, in situ spectroscopy, and computational analyses, we disclose that atomically dispersed Pd sites kinetically favor co-generation of *CO and *NH2 via H2O dissociation-driven proton transfer, forming an optimal intermediate balance. The dual metal active sites enhance C–N coupling via combined electronic and geometric effects, substantially lowering the reaction energy barrier and improving selectivity. This work provides a rational design strategy for advanced multifunctional catalysts for urea electrosynthesis, contributing to carbon neutrality and waste nitrogen valorization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3805-1
The sluggish kinetics of oxygen reduction and evolution reactions (ORR/OER) at the air electrode impede the practical deployment of fiber zinc-air batteries (FZABs) for wearable electronics. Conventional bifunctional catalysts suffer from an inherent activity trade-off due to the distinct mechanisms of ORR and OER. Here, we propose a spatial decoupling strategy to overcome this limitation by engineering isolated Fe single atoms and Fe–Ir dual-atom pairs on a nitrogen-doped carbon matrix (Fe/FeIr-NC). In this architecture, Fe single atoms serve as ORR centers, while Fe–Ir pairs with tunable spacing are tailored for OER, enabling complete functional separation and independent optimization. The catalyst exhibits an ORR half-wave potential of 0.91 V and an OER overpotential of 250 mV at 10 mA cm−2, yielding a record-low bifunctional gap (ΔE = 0.57 V) that outperforms all reported single- and dual-atom catalysts. A flexible fiber zinc-air battery based on this catalyst delivers a peak power density of 3920 W kg−1, along with a 1.4-fold increase in energy efficiency and a 2.6-fold extension in cycle life compared to the commercial Pt/C + IrO2 benchmark. This work not only breaks the traditional activity trade-off in bifunctional catalysis but also offers a promising route toward high-performance power sources for wearable electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3725-1
Conductive hydrogel-based stretchable electronics have been extensively investigated, with strain sensors being the most prominently studied. While mechanical properties significantly affect device performance, the systematic correlation between specific mechanical parameters and sensing performance remains rarely explored. This work compares the influences of Young’s modulus and mechanical hysteresis on sensing performance between highly entangled PAM-Li and double-network PAM-Li-Agar-3 strain sensors. Owing to the brittle agar network, which imparts a higher Young’s modulus and pronounced mechanical hysteresis to the double-network PAM-Li-Agar-3 hydrogel, the corresponding sensor requires a greater driving force for deformation and yields signals with poor reproducibility. In contrast, the PAM-Li hydrogel, characterized by highly entangled polymer chains, exhibits a lower Young’s modulus and negligible mechanical hysteresis. Consequently, signals from the PAM-Li strain sensor demonstrate enhanced sensitivity and stability. Therefore, this work demonstrates that a low Young’s modulus and minimal mechanical hysteresis are critical factors for achieving superior sensing performance in strain sensors, as systematically validated through comparative analyses across diverse application scenarios.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3773-7
Kesterite Cu2ZnSn(S,Se)4 (CZTSSe) solar cells suffer from significant open-circuit voltage (VOC) deficits due to severe interfacial and bulk recombination, restricting their power conversion efficiency (PCE) far below the Shockley-Queisser limit. This work proposes a low-temperature annealing strategy during ITO sputtering (SA) to synergistically address these challenges. The temperature applied during ITO sputtering not only improves the crystallinity, carrier concentration, and optical transmittance of the ITO layer but also promotes the diffusion of In from ITO into both CdS and CZTSSe layers. Consequently, lattice matching at the CZTSSe/CdS interface is optimized, enabling epitaxial growth. And a favorable ITO/In:CdS/In&Cd:CZTSSe structure with optimal band alignment is obtained. As a result, a champion device with a PCE of 14.29% was achieved. The SA-treating also enabled the CZTSSe solar cells to achieve the highest VOC reported to date, exceeding 590 mV. This underscores the essential role of SA processing in optimizing interface engineering and suppressing defects, thus promoting the development of low-cost, high-performance kesterite photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3767-9
Progressive skin fibrosis ultimately results in irreversible contractures, causing both joint dysfunction and cosmetic deformity. The key pathological features of skin fibrosis include persistent inflammation and abnormal accumulation of the extracellular matrix (ECM), with epithelial-mesenchymal transition (EMT) playing a critical role in disease progression. However, current therapeutic strategies for cutaneous fibrosis are largely palliative and often require repeated interventions, with limited efficacy. Celastrol (Cel) exerts anti-inflammatory and anti-fibrotic effects in skin tissue, but its clinical application is limited by poor bioavailability and a narrow therapeutic window. Tetrahedral framework nucleic acid (tFNA), a novel nanocarrier system, exhibits multiple advantages, including enhanced cellular uptake, improved cell viability, and intrinsic anti-fibrotic and anti-inflammatory properties. Therefore, this study applied tFNA-Cel complex (TCC) as an advanced nanotherapeutic agent, designed to exert a synergistic anti-fibrotic effect. In this study, an in vitro model of skin fibrosis was established using human keratinocyte (HaCaT) cells treated with 5 ng mL−1 transforming growth factor beta (TGF-β) for 24 h. The results showed that TCC significantly inhibited EMT progression by reducing α-smooth muscle actin (α-SMA) levels and increasing E-cadherin level. Compared to tFNA or Cel alone, TCC exhibited superior anti-fibrotic effects in the fibrosis model, as evidenced by modulation of SMAD family member 2 (SMAD2) signaling and collagen I expression. Furthermore, the TCC group showed lower levels of nuclear factor κB p65 (NF-κB p65), BCL-2-associated X protein (Bax), and reactive oxygen species (ROS) compared to the Cel or tFNA groups. These findings highlight TCC as a promising treatment for skin fibrosis, with its synergistic anti-fibrotic effects providing new therapeutic avenues.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3728-5
Biological intelligence achieves exceptional energy efficiency and environmental adaptability, exemplified by the human brain's ~20 W resting power consumption. A key strategy is the use of multi-ions as signal carriers for transduction and processing. Iontronics, employing ions instead of electrons, offer a promising route to low-energy, heat-dissipation-free devices for memory, sensing, and neuromorphic computing. However, conventional iontronics require external voltage bias to drive ion motion, complicating miniaturization and integration. Here, we highlight a recent breakthrough by Guo et al. reporting a bias-free iontronic memory sensor ('memsensor') that operates by controlling surface ion migration. The device couples vanadium dioxide (VO2) with a low-work-function indium (In) patch. Upon immersion in NaCl solution, In3+ ions generated electrochemically within the Debye length are driven by the intrinsic surface electric field to diffuse into the VO2 surface, inducing an insulator-to-metal phase transition and a measurable, non-volatile change in surface conductance. This conductance state correlates with NaCl concentration and can be reversibly restored by H2O2 treatment. The memsensor emulates the gustatory plasticity of C. elegans, mimicking the response dynamics of ASEL and ASER neurons. In a proof-of-concept, a model boat equipped with the memsensor exhibits adaptive chemotaxis: after 'starvation' training in high NaCl concentration, it avoids high-concentration zones; conversely, after training in low concentration, it migrates toward high-concentration zones. This work demonstrates a bias-free strategy for programmable memory and sensing, potentially advancing autonomous microsystems and bioinspired electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3772-y
Conformal contact between functional electronic films and biological surfaces is critical for long-term device stability, high signal sensitivity, and favorable signal-to-noise ratio. Traditional transfer methods, such as soft stamps and pad printing, often involve mechanical pressing, leading to poor conformality, localized stress concentration, or structural failure. Alternative strategies, including geometric engineering of non-stretchable materials or using stretchable organic alternatives, mitigate these issues but increase design complexity and reduce fabrication efficiency. Here, we highlight a novel 'drop-printing' strategy introduced by Li et al. that leverages capillary force to manipulate a water droplet to pick up a thin film, transfer it to a target substrate, and print it onto the surface. As the droplet evaporates, the film conformally wraps the surface. The droplet acts as a lubricating layer, while interfacial liquid penetrating microstructures generates capillary pressure, facilitating shape-adaptive deformation and significantly reducing stress concentration. The final positioning and conformality are governed by droplet behavior on the target surface. This approach achieves positional deviation of less than 20 μm via regulation of three-phase contact lines. The strategy enables damage-free conformal wrapping of non-stretchable films onto three-dimensional biological surfaces, as demonstrated by drop-printed silicon microfilm conformally wrapping on a rat brain, with successful NIR laser stimulation triggering forelimb movement and synchronized brain electrophysiological signals. This gentle, high-precision method addresses the pressing need for low-stress conformal bioelectronics, offering a general solution for diverse biological interfaces.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507054
In many Chinese wastewater treatment plants (WWTPs), residual chlorine is still manually monitored at low frequencies, leading to imprecise disinfectant dosing. This study systematically compared four machine learning models—backpropagation (BP) neural network, long short-term memory (LSTM) neural network, random forest (RF), and support vector regression (SVR)—for predicting chlorine consumption (i.e., the difference between chlorine dose and residual chlorine) during non-monitoring periods under different residual chlorine monitoring frequencies (every 1, 2, 4, 6, and 8 h). Using data from Plant A (equipped with online residual chlorine monitoring) and Plants B and C (manual monitoring every 6 h and 8 h, respectively), input variables included online water quality indicators (temperature, flow, NH3-N, CODCr, TP, TN) and chlorine dose. Results showed that at 1-h intervals, LSTM achieved the highest prediction accuracy; at 2–4-h intervals, RF performed best; at 6-h or lower frequencies, BP was superior; SVR performed worst across all frequencies. Validation on Plants B and C confirmed BP's optimal performance under low-frequency conditions, and particle swarm optimization (PSO) significantly improved its accuracy. These findings provide a basis for selecting appropriate machine learning models for chlorine consumption prediction under varying monitoring frequencies, particularly low-frequency manual monitoring, thereby supporting precise disinfectant dosing control.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3912-0
This erratum corrects an error in the Chinese name of co-first author Tianxiao Xiao (肖天孝) as originally published in the article 'A multi-modal smart chest patch for real-time cardiopulmonary monitoring and anomaly detection' (Sci China Mater, 2025, 68(12): 4413–4422). The corrected Chinese name is 肖天笑. The correction applies solely to the author's name and does not affect the scientific content, experimental data, or conclusions of the original paper. The authors and publisher apologize for any inconvenience caused.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507021
The accumulation of heavy metals in soil around municipal solid waste landfills poses potential risks to human health. This study selected a municipal solid waste landfill and monitored the concentrations of eight heavy metals (Zn, Pb, Cd, Ni, Hg, Cu, As, Cr) in surrounding soil. The geo-accumulation index method was used for pollution assessment, and a health risk assessment model recommended by the USEPA, combined with Monte Carlo uncertainty analysis, was employed to evaluate the pollution status and health risks to nearby residents. Results showed that among the eight metals, Pb, Ni, and Cd exceeded risk screening values at 4.26%, 6.38%, and 4.26% of sampling points, respectively. Geo-accumulation indices indicated overall clean conditions (mean < 0), but slight pollution by Pb, Zn, Ni, Hg, and Cd at some points. Probabilistic risk assessment based on Monte Carlo simulation revealed that for both adults and children, the cumulative non-carcinogenic risk was negligible, while carcinogenic risk was acceptable. However, there was a very low probability (approximately 0.2%) of non-carcinogenic risk for children, and probabilities of unacceptable carcinogenic risk were 0.64% for adults and 3.21% for children. Nickel was the primary contributor to carcinogenic risk, and children faced higher health risks than adults. These findings provide a reference for pollution prevention and health risk management of soil around municipal solid waste landfills.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507027
Ammonia nitrogen (NH3-N) is a common water pollutant that can induce eutrophication and threaten aquatic ecosystems and human health. Accurate monitoring is essential for water safety. This study applied a self-developed gas-permeable membrane-based conductivity sensor (GPMCS) for real-time in-situ monitoring of NH3-N in two water bodies. In the Qunying River (surface river water), GPMCS captured concentration fluctuations linked to pump operations and sewage intrusion, with mean inlet and outlet concentrations of 4.67 and 3.42 mg/L, respectively. In Swan Lake (landscape aquaculture water), concentrations reached up to 11.16 mg/L, with site means of 6.42 and 7.04 mg/L, influenced by aquaculture activities, weather, and location. GPMCS results correlated strongly with national standard methods (r1=0.8132, r2=0.7483), confirming accuracy and reliability. Compared to existing techniques, GPMCS offers high selectivity, strong anti-interference, portability, no sample pretreatment, low cost, and environmental friendliness, making it suitable for long-term in-situ monitoring. This technology provides robust support for sustainable water environment management.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506053
Red mud, a highly alkaline industrial solid waste from alumina production, poses severe environmental risks due to its high alkalinity, low organic matter content, and poor aggregation, which critically impede its soil reconstruction and ecological utilization. This study proposes a novel approach of low-temperature micro-oxidation to drive the synergistic soil reconstruction of red mud and coal. By constructing a low-temperature micro-oxidation atmosphere, the soil properties of the reaction products were investigated, the decomposition and reconstruction of alkaline minerals and alkali release were analyzed, and the oxidation of carbon-based minerals and organic matter transformation in coal were examined. The mechanism of the synergistic reaction between red mud and coal under low-temperature micro-oxidation was elucidated. Results showed that at 250 °C under micro-oxidation, the pH of the product decreased to 8.47, organic matter content increased to 12.98%, and the proportion of aggregates >0.250 mm increased. Alkaline minerals such as cancrinite and grossular in red mud underwent decomposition and reconstruction in the low-temperature hydrothermal environment, releasing substantial free alkali. The condensed aromatic rings of carbon-based minerals in coal were oxidized by free radicals, leading to ring-opening and bond cleavage, producing small-molecule organic acids and macromolecular humic acids. The continuous oxidation of carbon-based minerals in coal generated acids, which neutralized the alkali released from red mud, driving sustained dealkalization. The inorganic particles of red mud flocculated with macromolecular humic acids, forming micro-aggregates and significantly improving soil properties. This research provides technical support for the rapid ecological utilization of red mud at industrial scale.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507030
Arsenic is a toxic metalloid predominantly present in water as As(V) and As(III), whose speciation governs toxicity and mobility. Conventional speciation methods (HPLC-ICP-MS, IC-HG-AFS) offer ultralow detection limits but suffer from high cost, long analysis times, and non-portability, hindering on-site rapid monitoring. This study presents a sulfide-based spectrophotometric method exploiting the quantitative reaction between As(V) and S2− to form monothioarsenate (H3AsO3S) with a characteristic absorption at 233 nm. Under optimized conditions (H+ concentration 1 mol·L−1, Na2S dosage 5 mmol·L−1, reaction time 3 min, N2 purging 2 min), As(V) is directly quantified. Total arsenic is determined after complete oxidation of As(III) to As(V) using NaClO (10 mmol·L−1, pH 12, 5 min), and As(III) is obtained by difference. The method exhibits linearity over 0.5–50 mg·L−1 (A = 0.0209c + 0.0627, R² = 0.999), a detection limit of 0.17 mg·L−1, spike recoveries of 101.9%–104.1%, and relative standard deviation of 1.06%. Validation against real industrial wastewater samples showed relative deviations <10% compared with HPLC-ICP-MS and IC-HG-AFS. Total analysis time is within 15 min. The method is simple, cost-effective, and suitable for field monitoring.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507043
Municipal sludge with high moisture content and strong viscosity tends to form a dense crust during conventional rotary drum drying, reducing heat and mass transfer efficiency and prolonging drying time. This study proposes a thermal steel ball-enhanced rotary drum drying method that introduces high heat capacity, high thermal conductivity steel balls to achieve synergistic contact heat conduction and mechanical disturbance. An evaluation system incorporating dimensionless moisture ratio (MR), drying rate (DR), characteristic drying time (tdry), effective moisture diffusivity (Deff), and volumetric evaporation intensity (U) was established. Results show that compared with conventional drying, steel ball-enhanced drying increased maximum drying rate (DRmax) by 22.59%–41.19%, U by 38.06%–93.43%, and shortened tdry by 27.56%–48.30%, with more pronounced advantages under high load conditions. Deff was significantly higher throughout the process, with maximum increase up to 48.30%, indicating that ball rolling and collision effectively disrupt the crust and promote moisture migration. Mechanistic analysis reveals that the performance enhancement arises from the dual action of thermal-mechanical coupling and mechanical disturbance, which enhances local heat flux via contact conduction and dynamically renews the drying interface, shortening diffusion paths. This study elucidates the heat and mass transfer mechanisms of thermal steel ball-enhanced sludge drying, providing theoretical support and technical reference for efficient sludge volume reduction and dryer design optimization.