SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4472-0
Dynamic electrocardiography (ECG) monitoring during physical activity remains compromised by motion artifacts that corrupt signal fidelity, particularly with conventional gel electrodes whose impedance rises sharply under deformation. This work presents a thumb-sized liquid metal system integrating gallium-based epidermal electrodes with a self-adhesive elastomeric matrix to sustain robust ECG acquisition against motion. The electrodes exploit the fluidic compliance of eutectic gallium–indium to maintain continuous skin contact, while the adhesive formulation ensures stable interfacial coupling without additional fixation. The system achieves low motion artifact levels, preserving waveform morphology and R-peak detectability during ambulation. The compact form factor enables unobtrusive wearability, and the materials architecture addresses the trade-off between adhesion and conformability that limits existing dry electrodes. The study establishes a materials and device pathway for clinical-grade dynamic ECG in ambulatory and point-of-care settings, with implications for continuous cardiac monitoring where patient movement is unavoidable.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4433-5
Negative thermal expansion (NTE) and zero thermal expansion (ZTE) materials are technologically relevant for precision engineering, yet their practical deployment is constrained by narrow operating temperature windows. This study introduces an entropy-designing strategy to regulate the thermal expansion behavior in the AⅠBⅡCⅢMo3O12 system, specifically K0.4(Mg0.25Mn0.25Co0.25Ni0.25)0.4Sc1.6Mo3O12 (CE0.4MO) and related CExMO compositions (x = 0.4, 0.6, 0.8, 1.0). By tuning configurational entropy, the operating temperature windows for both NTE and ZTE are significantly broadened, with the ZTE region shifting to higher temperatures. Among single-phase compositions, CE0.4MO exhibits the lowest configurational entropy and demonstrates NTE from 100 to 830 K and ZTE up to 1100 K, surpassing most reported ZTE materials. Systematic analyses of structural evolution, lattice dynamics, and electronic structure reveal that reduced configurational entropy suppresses structural evolution, directly correlating with decreased structural flexibility. Higher atomic displacement parameters (ADPs) of oxygen in CE1.0MO provide experimental evidence for enhanced flexibility. Raman spectroscopy shows that the full width at half maximum (FWHM) of peaks in the 750–900 cm-1 range positively correlates with configurational entropy, indicating reduced lattice disorder, while modes within 750–1050 cm-1 blue-shift as entropy decreases, confirming lattice stiffening. Electron localization function (ELF) and charge density analyses indicate that Mg/Mn/Co/Ni/Sc–O bonds are ionic, with ionicity weakening as configurational entropy decreases, thereby enhancing constraints on atomic vibrations and reducing structural flexibility. This work establishes a theoretical foundation for designing thermal expansion materials with wide operating temperature ranges.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4371-6
The sluggish kinetics of the oxygen reduction reaction (ORR) necessitates platinum-based catalysts, but their high cost and scarcity drive the search for platinum-group metal-free (PGM-free) alternatives. Fe−N−C catalysts with atomically dispersed Fe−N4 sites are promising, yet their practical performance is limited by buried active sites and poor mass transport. Here, a crumpled, multi-scale porous Fe−N−C catalyst (Fe−N−PCG) is synthesized via spray pyrolysis coupled with high-temperature metal etching. The crumpled morphology, formed by capillary compression during rapid solvent evaporation, and in-plane mesopores from Fe nanoparticle etching, synergistically enhance site accessibility and mass transport. Fe−N−PCG achieves a site density (SD) of 2.74×10^19 sites g−1 and Fe utilization (UFe) of 51.7%. As a gas diffusion electrode, it delivers a mass transport overpotential (ηmt) of 67 mV at 800 mA cm−2. In zinc-air batteries, Fe−N−PCG exhibits a peak power density of 296.1 mW cm−2 at 500 mA cm−2, outperforming Pt/C (241 mW cm−2 at 438 mA cm−2). At 50 mA cm−2, it delivers a discharge voltage of 1.19 V and a specific capacity of 815 mAh g−1, surpassing Pt/C (1.13 V, 715 mAh g−1). These results demonstrate that morphology and porosity engineering can concurrently optimize intrinsic activity, site utilization, and mass transport, offering a rational design strategy for high-performance PGM-free catalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4248-2
Marine biofouling imposes substantial operational penalties on maritime assets, yet commercial silicone foul-release coatings rely on static, non-adaptive networks that cannot be reprocessed or repaired. This work introduces selenonium-salt-catalyzed dynamic siloxane exchange as a route to polydimethylsiloxane (PDMS) vitrimer coatings. The authors incorporate A16Se+ organoselenium catalysts into PDMS networks at loadings designated A16Se+xPDMS, enabling thermally activated siloxane bond exchange that confers vitrimeric stress relaxation, reprocessability, and high-temperature self-healing. Antibiofouling performance is benchmarked against pristine PDMS using colony morphology assays for Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa, SEM imaging of bacterial adhesion after 3 h, Chlorella fluorescence adhesion quantification, zeta potential measurements, and 3-month seawater immersion panels. Reviewer 1 questioned the direct relevance of recyclability and high-temperature self-healing to marine antifouling and requested that surface elastic modulus and Pseudomonas antibacterial data be elevated to the main text. In response, the authors relocated scratch and self-healing results from Figure 5 to Supporting Information Figures S12 and S13, condensed the main-text discussion, and integrated surface elastic modulus data into Figure 4G and Pseudomonas antibacterial results into Figure 6A. The revised manuscript positions dynamic exchange as supporting evidence of network dynamics rather than as a primary antifouling metric, while foregrounding modulus and antibacterial performance as the application-relevant properties.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4267-y
The synthesis of two-dimensional MBenes from MAB-phase ceramics is impeded by uncontrolled etching kinetics that compromise structural integrity and yield. This study introduces a vacuum molten salt strategy to regulate space-charge accumulation during the selective removal of Al from Mo2AlB2, producing honeycomb-like architectures. The vacuum environment suppresses oxidative side reactions and modulates ionic transport, enabling precise control over etching depth and morphology. The resulting Mo2AlB2 exhibits exceptional electromagnetic wave absorption, with a minimum reflection loss of -56.3 dB at 2.4 mm and an effective absorption bandwidth of 6.8 GHz. These metrics surpass conventional etching-derived MBenes by a factor of 2.5 in attenuation capacity. The space-charge-regulated mechanism is elucidated through in situ spectroscopic and computational analyses, revealing that vacancy-induced charge redistribution governs the etching front propagation. This work establishes a scalable route for high-purity MBenes with tailored porosity, addressing critical bottlenecks in energy absorption and catalytic applications. The vacuum molten salt approach eliminates the need for hazardous HF, offering a safer and more environmentally benign pathway for industrial translation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4362-y
The commercial viability of zinc-air batteries (ZABs) is constrained by the sluggish kinetics of the oxygen reduction reaction (ORR), which necessitates robust, cost-effective catalysts. While cobalt-based single-atom catalysts (Co SACs) exhibit superior selectivity and stability relative to Fe-N-C counterparts, their intrinsic ORR activity remains limited by scaling relations among intermediates. This study alleviates these constraints by precisely engineering the coordination symmetry of Co SACs. Through a mild annealing strategy, boron was incorporated into the first and second coordination shells of Co centers, creating an asymmetric Co-N3B-O local environment. The first-shell B/O coordination modulates the electronic structure of the Co center, while hydrogen bonding between *OOH and the coordinated O atom stabilizes the key intermediate, synergistically enhancing ORR activity. The optimized Co-BCN-950 catalyst delivers a peak power density of 216 mW cm-2 in ZABs, a 43% enhancement over commercial Pt/C (151 mW cm-2), alongside an open-circuit voltage of 1.43 V and a specific capacity of 790 mAh g-1. These findings establish a paradigm for tailoring the local coordination of SACs, enabling next-generation high-stability energy storage systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4452-8
Europium(III) complexes offer intrinsically narrow red emission (full-width at half-maximum < 5 nm) that is highly desirable for ultrahigh-definition displays, yet their electroluminescence performance is severely limited by unbalanced charge transport and inefficient energy transfer. This work reports a molecular design strategy that modulates both energy transfer and charge transport in Eu³⁺ OLEDs. The synthesized complex, Cz-Eu, incorporates a carbazole-functionalized ancillary ligand to facilitate host–guest energy transfer and hole transport. The single-crystal structure was deposited (CIF: Cz-Eu-cif.cif) and subjected to PLATON validation, which flagged 3 type-1 alerts (CIF construction/syntax errors), 8 type-2 alerts (possible structural model deficiencies), 12 type-3 alerts (low structure quality), and 4 type-4 alerts (improvement suggestions), with no duplication detected. These crystallographic alerts indicate that the reported structure requires further refinement before it can be considered reliable. Nevertheless, the device metrics demonstrate a promising route: the optimized OLED achieves efficient ultranarrow-band red emission, with the potential for high color purity and reduced power consumption. The findings underscore the critical role of ligand engineering in balancing charge fluxes and fostering efficient energy transfer, providing a viable pathway for next-generation red emitters. However, the structural ambiguities highlighted by the PLATON analysis warrant cautious interpretation of the structure–property relationships and suggest that additional crystallographic and device stability studies are necessary to substantiate the claimed performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4383-8
Conventional cancer therapies remain constrained by undruggable oncogenic proteins and acquired resistance. Proteolysis targeting chimeras (PROTACs) have emerged as a transformative modality that harnesses the ubiquitin-proteasome system to selectively degrade target proteins, offering advantages over traditional small-molecule inhibitors. However, clinical translation of PROTACs is impeded by intrinsic physicochemical limitations: high molecular weight, poor bioavailability, and lack of tumor-specific delivery. Integrating PROTACs with nanotechnology has yielded advanced nano-PROTACs platforms. Nanocarriers enhance solubility and stability, optimize pharmacokinetics, and enable spatiotemporally controlled drug release through passive or active targeting. This review systematically summarizes recent advances in engineering multifunctional nano-PROTACs for cancer therapy, with particular emphasis on design strategies by which nanoengineering enhances PROTAC performance. We evaluate how these platforms improve anticancer efficacy and minimize systemic toxicity while exploring their therapeutic potential in monotherapy and synergistic treatment settings. Finally, we discuss current challenges and future perspectives, providing a theoretical and technical foundation for next-generation nano-PROTACs as a precise and potent strategy in precision oncology.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4412-y
GeTe-based thermoelectric materials are promising lead-free alternatives to PbTe, but their intrinsically high Ge vacancy concentration (~10^21 cm^-3) leads to excessive carrier density and degraded Seebeck coefficient. This study integrates resonant levels (RLs) via In doping and local van der Waals gaps via Sb/Bi alloying to decouple electron and phonon transport. The optimal composition Ge0.91Sb0.04Bi0.04In0.01Te exhibits a Seebeck coefficient of ~287.31 μV K^-1 at 323 K, more than double that of the In-free sample (~102.28 μV K^-1). The peak figure of merit zT reaches ~1.8 at 723 K, with an average zT of ~1.0 over 323–723 K. Vickers hardness is enhanced to ~224 HV, a ~93% improvement over pristine GeTe (~116 HV). X-ray diffraction reveals a structural evolution toward a pseudo-cubic phase with increasing In content, and the (202) peak shifts to lower angles, indicating lattice expansion. These results demonstrate that synergistic RLs and van der Waals gaps effectively optimize carrier concentration and suppress thermal conductivity, offering a viable route for high-performance, mechanically robust GeTe thermoelectrics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4405-9
Conventional metal-halide X-ray scintillators, including Bi4Ge3O12 (BGO), Cs(Na)I:Tl, and Lu1.8Y0.2SiO5:Ce (LYSO), suffer from hygroscopic decomposition, high-temperature fabrication, and mechanical rigidity, which restrict their deployment in harsh-environment radiography. This study reports a nontoxic zero-dimensional organic–inorganic hybrid copper(I) halide, Cu2I2(C26H36NP)2 (Compound G), synthesized via a room-temperature solution route. The bulky phosphine ligands confer exceptional superhydrophobicity, with the material retaining 91.95% of its initial luminescence after 30 days of water immersion. A flexible scintillator screen fabricated from styrene-ethylene-butene-styrene (SEBS) exhibits a light yield of ~32,500 photons MeV-1, a spatial resolution of 19.14 lp mm-1, and a detection limit of 0.8 μGyair s-1. The screen enables stable X-ray imaging under flexible, high-temperature, and underwater conditions, eliminating vignetting and distortion in nonplanar objects. These metrics demonstrate that the superhydrophobic copper(I) halide scintillator addresses the water-stability bottleneck of commercial scintillators while delivering competitive light output and resolution, offering a viable pathway for medical diagnosis, nondestructive inspection, security checking, and space exploration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4416-8
Copper(I)-based carbene-metal-amide (CMA) emitters offer an earth-abundant alternative to precious-metal phosphors for organic light-emitting diodes (OLEDs), yet efficient green emission remains scarce due to limited π-extension and unbalanced charge-transfer characteristics of N-heterocyclic carbene (NHC) ligands. This work introduces a pyrimidine-fused NHC ligand (CF3PMI) with balanced π-accepting ability, synthesized via a one-pot protocol in good yields. The resulting Cu(I)-CMA complex CF3PMI-BFCF3 exhibits green thermally activated delayed fluorescence (TADF) in doped thin films, with a photoluminescence quantum yield (PLQY) of 90% and a short emission lifetime of 1.16 μs. A vacuum-deposited OLED achieves green electroluminescence centered at 514 nm with an external quantum efficiency (EQE) of 22.7%. Furthermore, a hyperfluorescent OLED employing CF3PMI-BFCF3 as a sensitizer delivers an EQE of 21.8%, green emission at 537 nm, and a narrow full width at half maximum (FWHM) of 30 nm. These results establish a viable molecular design strategy for high-performance green-emitting Cu(I)-based TADF materials and provide a convenient synthetic route for Cu(I)-CMA emitters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4494-9
Superionic conductors exhibit high cation mobility arising from weak binding and continuous transport pathways, atomistically characterized by extensive structural disorder and partial occupancy akin to amorphization. This disorder, whether confined to a cation sublattice or extended to full amorphization, strongly impedes lattice thermal transport, rendering these materials intrinsically ideal thermal insulators. This work investigates Ag26I18W4O16, a superionic conductor tunable from fully amorphous to single-crystalline states, as a model system to probe the impact of disorder and amorphization on thermal transport. Extensive Ag+ disorder, in both crystalline and amorphous phases, reduces thermal conductivity to approximately the theoretical lower bound of 0.16 W/m-K with virtually no temperature dependence, while concurrently achieving the lowest mean sound velocity ever recorded for a dense solid. Pair distribution function (PDF) analysis of synchrotron X-ray total scattering data indicates that short-range disorder (< 5 Å), rather than long-range periodicity, governs thermal insulation performance in both phases. These findings suggest a design strategy reconciling structural stability with glass-like thermal insulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4313-7
Liquid-to-vapor mass transfer is central to energy and environmental processes. Conventional distillation relies on vapor-liquid equilibrium and device-level optimization, with materials playing passive structural roles. Non-boiling processes such as membrane distillation and interfacial solar evaporation localize phase change at confined interfaces, making mass transfer a materials-mediated transport phenomenon where interfacial structure and chemistry dictate evaporation kinetics, vapor escape, and solute rejection. Janus interface materials, featuring spatially separated hydrophilic and hydrophobic domains, introduce architectural asymmetry to regulate liquid-to-vapor mass transfer. This review summarizes recent advances, highlighting mechanisms including the cooperative pump-valve effect, nanoconfinement-enhanced transport, and mitigation of fouling and scaling. Representative applications in membrane distillation, solar-driven evaporation, and personal thermal-moisture management are systematically discussed. Key challenges and future opportunities are outlined, particularly in advancing fundamental understanding, scalable fabrication, and practical implementation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4324-4
Magnesium-oxygen (Mg-O2) batteries offer high theoretical energy density and low-cost earth-abundant magnesium, yet practical deployment has been impeded by poor cycling stability and low energy efficiency, primarily due to the sluggish decomposition of conventional MgOx discharge products. Here we demonstrate that trace water in the electrolyte redirects the cathodic reaction to form chemically reactive Mg2(OH)3Cl·4H2O as the main discharge product, enabling a new reversible pathway: 8Mg2+ + 4Cl- + 3O2 + 22H2O ⇋ 4Mg2(OH)3Cl·4H2O. This water-mediated chemistry significantly enhances redox reversibility compared with the MgOx route. The resulting Mg-O2 battery delivers over 324 stable cycles at 1000 mA·g-1 with a capacity of 500 mAh·g-1 and an energy efficiency of 92%, surpassing all previously reported Mg-O2 systems. The electrolyte comprises 0.25 M magnesium bis(trifluoromethanesulfonyl)imide (Mg(TFSI)2) and 0.5 M magnesium chloride (MgCl2) in ethylene glycol dimethyl ether (DME) with a trace amount of water. These findings establish a general strategy for reversible Mg-O2 electrochemistry and provide a new design paradigm for practical magnesium-based energy storage.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4468-6
The proliferation of multispectral detection platforms demands materials that simultaneously satisfy electromagnetic interference (EMI) shielding and infrared (IR) camouflage without compromising radio-frequency (RF) transmission. Conventional MXene films exhibit exceptional EMI shielding (>40 dB) but suffer from high IR emissivity and severe RF reflection, precluding integration with wave-transmitting arrays. This work introduces liquid metal (LM)-modified MXene composite films engineered via structural patterning to decouple optical, IR, and RF responses. The LM phase, dispersed within the MXene interlayer galleries, reduces free-electron density and tailors the dielectric loss, while a periodic array architecture creates impedance-matched windows for RF transmission. The resulting films achieve an EMI shielding effectiveness of 36 dB at 510 µm thickness, with a low IR emissivity of 0.36 and an RF transmittance exceeding 80% in the X-band. The patterning strategy suppresses surface current continuity, mitigating the trade-off between shielding and transmission. These metrics represent a 20% improvement in IR camouflage and a 15% enhancement in RF transparency relative to pristine MXene films. The composite films also demonstrate mechanical flexibility, retaining 95% of initial conductivity after 1,000 bending cycles. This work establishes a scalable route for multispectral-compatible materials critical for next-generation stealth and communication systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4238-2
Infrared nonlinear optical (IR NLO) materials are critical for laser frequency conversion, yet their performance is often constrained by a trade-off between second harmonic generation (SHG) efficiency and laser-induced damage threshold (LIDT). Here, we report a new ternary diamond-like compound, AlGaS3, which successfully balances these competing demands. AlGaS3 crystallizes in a noncentrosymmetric structure composed of wide HOMO-LUMO gap [AlS4] tetrahedra and NLO-active [GaS4] tetrahedra. The compound exhibits a wide experimental optical band gap of approximately 3.38 eV, which is significantly larger than that of the benchmark AgGaS2 (AGS, ~2.70 eV). This wide band gap contributes to a high laser-induced damage threshold (LIDT) of approximately 6.0 times that of AGS, as determined by powder-based measurements. Notably, AlGaS3 also demonstrates a phase-matching SHG response of approximately 0.5 times that of AGS at a fundamental wavelength of 2.09 μm, with particle size-dependent behavior confirming phase-matchability. The combination of wide band gap, high LIDT, and moderate SHG response positions AlGaS3 as a promising candidate for high-power IR NLO applications. This work provides a viable strategy for designing IR NLO materials with enhanced laser damage resistance by incorporating wide-gap tetrahedral units.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4502-1
Near-infrared-II (NIR-II, 1000-1700 nm) luminescent materials are pivotal for deep-tissue bioimaging and optical communication, yet their performance is often limited by low quantum yields and thermal quenching. Here, we report a thermal-enhanced NIR-II luminescence in Sb3+/Er3+ co-doped Cs3GdCl6 microcrystals synthesized via a modified Bridgman method. Under ultraviolet excitation, the co-doped microcrystals exhibit intense NIR-II emission centered at 1532 nm corresponding to Er3+: 4I13/2 → 4I15/2 transition, with a maximum relative sensitivity of 1.2% K−1 at 303 K. Notably, the integrated NIR-II emission intensity increases by 2.3-fold from 298 K to 373 K, demonstrating anomalous thermal enhancement. This behavior is attributed to the thermally activated energy transfer from Sb3+ sensitizers to Er3+ activators, as confirmed by temperature-dependent photoluminescence spectra and decay kinetics. The energy transfer efficiency reaches 86% at room temperature and further improves with rising temperature. The microcrystals also show excellent photostability, retaining 95% of initial intensity after 120 min continuous UV irradiation. Furthermore, we demonstrate a proof-of-concept wireless optical communication link using the microcrystals as a NIR-II phosphor, achieving a signal-to-noise ratio of 30 dB at 400 Hz modulation frequency. These findings provide a new strategy for designing thermal-enhanced NIR-II luminescent materials and expand their potential in temperature sensing and optical communication.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4138-5
Electrocoagulation (EC) has emerged as a promising electrochemical technology for wastewater treatment, offering distinct advantages over conventional chemical coagulation and membrane processes. This review systematically summarizes recent advancements in EC, focusing on the underlying mechanisms, key operating parameters, and diverse technical applications. The EC process involves three stages: electrolytic oxidation and in-situ coagulant formation, destabilization of contaminants, and floc formation. Unlike chemical coagulation, EC requires no external chemical additives, and process control is achieved by adjusting current density, voltage, or electrode materials, enabling adaptation to varying wastewater qualities. The review highlights the influence of dissolved organic matter (DOM) on EC efficiency, as clarified by Luo et al. (Water Research, 2025). Furthermore, it discusses reactor design innovations, including continuous-flow and cascade-type configurations, and the role of current waveforms in mitigating electrode passivation. The integration of EC with membrane bioreactors and forward osmosis is also examined, demonstrating enhanced treatment performance and fouling mitigation. Key challenges, such as energy consumption and electrode scaling, are addressed, along with future research directions. This comprehensive analysis provides a critical framework for optimizing EC systems and scaling them for industrial wastewater treatment, emphasizing the need for holistic reactor design and process integration to achieve sustainable water reuse.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4240-7
The electrocatalytic ammonia oxidation reaction (AOR) is pivotal for sustainable energy conversion and storage, enabling direct ammonia fuel cells (DAFCs), ammonia electrolysis, and solid oxide fuel cells. This review critically examines recent advances in AOR catalysis, emphasizing active-site regulation, interfacial engineering, and device-oriented catalyst development. For noble-metal catalysts, optimizing adsorption and dehydrogenation of NHx intermediates while mitigating poisoning is essential for sustained activity. Non-noble-metal systems, particularly Ni-based catalysts, require precise control of reconstructed working-state phases such as NiOOH-like species to balance activity and selectivity. Interfacial engineering, including heterointerfaces, defect structures, and doped coordination environments, strongly influences the competition between AOR and oxygen evolution reaction (OER), as well as product branching toward N2 or oxygenated nitrogen species. The review underscores that catalyst optimization now extends beyond bulk composition to the precise regulation of the interfacial reaction microenvironment. Furthermore, practical device operation is governed by membrane/electrolyte compatibility, mass transport, ammonia crossover, thermal management, and long-term durability. Bridging fundamental catalyst studies with deployable ammonia energy technologies requires coordinated optimization from active materials to electrode architectures and full-device systems. This review provides a comprehensive framework for designing next-generation AOR catalysts and accelerating their integration into industrial energy systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4269-4
Self-assembled molecular interlayers (SAMs) are promising hole-selective contacts for high-efficiency organic solar cells (OSCs) due to their well-defined energy alignment and minimal parasitic absorption. However, their intrinsically limited mechanical robustness often leads to structural degradation and performance loss under mechanical deformation, restricting their application in flexible devices. Here, we report a nanoparticle-reinforced self-assembled composite interface that simultaneously enhances mechanical reliability and optoelectronic performance. Uniformly dispersed SiO2 nanoparticles are introduced as high-modulus reinforcing building blocks without disturbing molecular self-assembly. In contrast to NiOx nanoparticles, which suffer from aggregation and parasitic absorption, SiO2 nanoparticles exhibit excellent dispersion and optical transparency, enabling formation of a structurally compatible hybrid interface. Mechanistic studies reveal that SiO2 nanoparticles redistribute interfacial stress and form dynamic hydrogen-bond networks with phosphonic acid groups of 2PACz, providing efficient energy dissipation during cyclic deformation. Meanwhile, modulation of interfacial polarity extends the crystallization time window of the active layer, resulting in enhanced molecular ordering and improved charge transport. As a result, devices based on the SiO2/2PACz composite interface achieve a power conversion efficiency of 20.14% for rigid devices and 19.30% for flexible devices, placing the flexible devices among the highest-performing flexible OSCs reported to date, while retaining over 90% of their initial efficiency after repeated bending cycles. This work establishes a general strategy for overcoming the trade-off between electronic selectivity and mechanical robustness in ultrathin self-assembled molecular interfaces, providing design insights for high-performance flexible organic optoelectronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4260-5
Lithium-sulfur batteries (LSBs) are recognized as a leading candidate for next-generation energy storage due to their high theoretical specific capacity (1675 mAh g⁻¹). However, the shuttle effect of lithium polysulfides (LiPSs) severely limits cycle life and energy efficiency. Here, we report a multi-interface engineering strategy employing a MnO₂-TiO₂@Ti₃C₂ MXene (MT@MX) heterojunction, synthesized via a facile redox reaction between MXene and KMnO₄, to modulate bidirectional polysulfide conversion. The 2D structure with high conductivity and abundant heterogeneous interfaces facilitates fast ion/electron transfer, reduces reaction energy barriers, and enhances adsorption via d-band center effects. The stepped built-in electric field (BIEF) in MT@MX lowers the migration energy barrier of LiPSs from catalytic MXene to TiO₂ and then to adsorptive MnO₂, enabling reversible migration across multi-interfaces. Optimized heterointerfaces synergistically integrate adsorption, diffusion, and catalytic conversion, yielding excellent cycling stability even at a high sulfur loading of 6.4 mg cm⁻². This work demonstrates that constructing heterojunctions with stepped BIEF offers a feasible approach to modulate interfacial diffusion and provides a new design strategy for high-performance LSB electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4319-x
This erratum corrects an error in the Acknowledgments section of the original article 'Investigation on graphene growth by roll-to-roll chemical vapor deposition' published in Science China Materials, Vol. 65, Issue 4, page 1042, 2022. The authors regret that the funding number (No. (2021)105) for the Shenzhen Science and Technology Program was incorrectly used. The correct funding number is No. KQTD20200820113010022. The authors apologize for any inconvenience caused. This correction does not affect the scientific content, results, or conclusions of the original paper. The original research focused on the kinetics of graphene growth via roll-to-roll chemical vapor deposition (CVD), a scalable method for producing high-quality graphene films. The study addressed challenges in continuous manufacturing, such as uniformity, growth rate, and defect control, and provided insights into optimizing process parameters for industrial-scale production. The erratum ensures accurate attribution of funding sources, maintaining the integrity of the research record.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4339-7
Neuromorphic computing demands energy-efficient synaptic devices that emulate biological plasticity. Optoelectronic memristors based on colloidal quantum dots (QDs) offer tunable bandgaps and solution processability, yet suffer from defect-mediated nonradiative recombination and instability. Here, we report ZnS-passivated CdZnSe core/shell QDs as the active layer in memristive devices, achieving enhanced synaptic emulation and information encryption. Time-resolved photoluminescence (TRPL) decay curves were fitted with a tri-exponential function, revealing that ZnS passivation suppresses defect-related trap states, prolonging the average carrier lifetime from 12.3 ns (CdZnSe) to 28.7 ns (CdZnSe/ZnS). The intensity proportion of the fast decay component (τ1 ≈ 1.2 ns) decreased from 45% to 18%, indicating reduced surface trapping. Devices incorporating CdZnSe/ZnS QDs exhibit stable bipolar resistive switching with an ON/OFF ratio exceeding 10^3, endurance of >10^3 cycles, and retention of >10^4 s. Under 365 nm UV illumination, the devices show light-tunable synaptic plasticity, including paired-pulse facilitation (PPF) with a facilitation index of 180% at a 50 ms interval, and transition from short-term to long-term memory. The memristors successfully emulate essential synaptic functions and are employed in a simple encryption scheme, demonstrating the potential of defect-passivated QDs for secure neuromorphic hardware.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4202-3
Carbon dots (CDs) with absorption in the second near-infrared window (NIR-II, 900-1700 nm) hold promise for tumor theranostics, yet existing synthesis methods often involve complex procedures, harsh conditions, or lack precise control. Here we report a 'self-photooxidation-restructuring' strategy that enables structural reorganization of the carbon core in CDs, achieving a significant redshift of absorption into the NIR-II region. Under ultraviolet (UV) light irradiation, the precursor (B-CDs, absorption in UV region) generates singlet oxygen, which self-oxidizes aldehyde groups and the carbon skeleton of B-CDs to stronger electron-withdrawing carboxyl groups and carbon radicals, respectively. These processes facilitate the formation of new C=C bonds between isolated aromatic domains, thereby transforming B-CDs into novel CDs (N-CDs) characterized by enhanced donor-acceptor interactions and a redshift in absorption toward the NIR-II window. Various experimental data, including high-resolution XPS, FTIR, NMR, EPR, have proved the proposed formation mechanism. The novel N-CDs afforded a high photothermal conversion efficiency of up to 71.33%, which enabled 1064 nm laser-activated photoacoustic imaging (PAI)-guided photothermal therapy (PTT) in tumors. This work opens a new avenue for the synthesis and modulation of CDs in the NIR-II region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4354-9
This review systematically examines the synthesis-structure-property relationships of hybrid graphene and carbon fiber reinforced composites, encompassing polymer, metal, and ceramic matrix systems. The hybridization of graphene with carbon fibers addresses the intrinsic limitations of conventional composites, such as weak interfacial bonding and insufficient multifunctionality. The review consolidates recent advances in fabrication strategies, including electrophoretic deposition, layer-by-layer assembly, and precursor impregnation, which enable controlled graphene distribution and orientation. Critical analyses of mechanical, tribological, electrochemical, and anti-ablation properties reveal that graphene addition significantly enhances interfacial shear strength, thermal stability, and electrical conductivity. For instance, in copper matrix composites, the incorporation of reduced graphene oxide with short carbon fibers improves tribological performance, reducing wear rates under specific load conditions. In ceramic matrix composites, graphene-modified C/C-SiC composites exhibit superior anti-ablation resistance, with mass loss rates reduced by up to 30% at elevated temperatures. Furthermore, graphene-coated carbon fiber electrodes demonstrate high specific capacitance and cycling stability in energy storage applications. The review also addresses challenges such as dispersion uniformity, scalability, and cost-effectiveness, proposing future directions for industrial adoption. By providing a comprehensive framework, this work guides the design of next-generation hybrid composites tailored for aerospace, automotive, and energy storage sectors.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4373-2
Infrared stealth technology demands materials with simultaneously low infrared emissivity and robust environmental stability. Traditional coatings suffer from high emissivity or poor thermal stability. Here, we report Sr-doped SmCoO3 perovskite ceramics achieving a record-low room-temperature infrared emissivity of 0.12 in the 8–14 μm atmospheric window. Systematic doping (x = 0, 0.1, 0.2, 0.3, 0.4, 0.5) via solid-phase synthesis reveals that Sr substitution induces a Co3+/Co4+ mixed valence state, increases oxygen vacancy concentration, and distorts the lattice. First-principles calculations (CASTEP) confirm that doping narrows the bandgap from 1.8 eV to 0.9 eV and enhances the double-exchange interaction, boosting carrier concentration and mobility. The optimized composition (x = 0.3) exhibits an electrical conductivity of 1.2×10^3 S/cm and a carrier density of 3.5×10^21 cm^-3, leading to strong infrared reflection. The material maintains emissivity below 0.15 after 100 hours of thermal cycling at 300°C and 500 hours of humidity exposure (85°C/85% RH), demonstrating exceptional environmental durability. This work establishes a new paradigm for designing high-performance inorganic infrared stealth materials via electronic-structural synergy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4342-3
Electron acceptors containing single-bond-linked building blocks offer attractive advantages for organic solar cells owing to their synthetic simplicity and structural modularity. However, achieving backbone planarity without compromising electronic compatibility remains a persistent challenge. Conventional conformational locking strategies based on alkoxy substitution can effectively suppress torsional freedom but often elevate the highest occupied molecular orbital energy level, limiting compatibility with widely used donor polymers. Here, we report a partially fused electron acceptor design that achieves intrinsic backbone planarity through heterocycle selection rather than side-chain-assisted conformational locking. By incorporating a benzodifuran core and furan-thiophene linkages, the resulting acceptors exhibit a near-coplanar backbone geometry as revealed by density functional theory calculations, without the need for electronically perturbing alkoxy groups. Devices based on the optimized acceptor (BDF-1) deliver a binary power conversion efficiency of 12.2%, and further improvement to 19.5% is achieved in a ternary blend with PM6 and BTP-eC9. The enhanced performance is accompanied by favorable morphology, balanced charge transport, and suppressed recombination losses. This work provides molecular-level insight into partially fused acceptor design and demonstrates that heteroatom-guided conformational locking offers a viable strategy for expanding the design space of acceptors with single-bond-linked building blocks while maintaining compatibility with mainstream donor systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4381-5
Bismuth telluride (Bi2Te3)-based alloys remain the benchmark for low-temperature thermoelectric applications, yet their conversion efficiency is limited by the trade-off between electrical and thermal transport. This study introduces a pseudo grain boundary engineering strategy to simultaneously enhance the average figure of merit (ZT) in p-type (Bi,Sb)2Te3 (BST) materials. By incorporating Ag-based compounds, the carrier concentration is optimized via substitution of Ag+ ions, while the introduction of secondary phases at grain boundaries effectively suppresses lattice thermal conductivity. The approach yields a peak ZT of 1.35 at 393 K and an average ZT of 1.25 across 303–483 K, representing a significant improvement over pristine BST. Compared to prior reports, this work achieves superior average ZT while maintaining high electrical conductivity, addressing the longstanding bottleneck of thermal conductivity reduction without compromising carrier mobility. The findings underscore the efficacy of pseudo grain boundary engineering in advancing Bi2Te3-based thermoelectrics for solid-state cooling and power generation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4367-4
Single-crystalline Cs3Cu2I5 has attracted considerable interest owing to its excellent scintillation performance and favorable stability. Nevertheless, second phases induced by peritectic reactions during melt growth give rise to deteriorated scintillation properties and promote crystal cracking. In this work, the effects of non-stoichiometric ratios of raw material (n(CsI)=0.57, 0.62, and 0.63) on the crystallization behavior and scintillation properties were systematically investigated. The results show that the crystal quality is optimal at n(CsI)=0.62, featuring high transparency, absence of macroscopic inclusions, and cracking free, with a PLQY of 79.3%. Temperature-dependent photoluminescence verifies the self-trapped exciton emission mechanism with strong exciton-phonon coupling, giving an exciton binding energy of 473.9 meV and a Huang-Rhys factor S of 79.8. The as-grown crystal exhibits an optimized light yield of 24,380 photons/MeV, an energy resolution of 3.8% for 137Cs (662 keV) γ-rays, a dominant decay time of 957 ns, and excellent linear response in the medium-to-high energy region. Precise regulation of the raw material stoichiometry can effectively suppress the formation of second phases, yielding high-quality Cs3Cu2I5 single crystals whose comprehensive performance demonstrates promising application potential in γ-ray detection.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4292-4
The vast compositional space of high-entropy materials presents a fundamental challenge for catalyst discovery. Considering 21 candidate elements at a 1% atomic resolution, this combinatorial explosion exceeds 10 billion (>10^10) possibilities, rendering direct experimental exploration impractical. Furthermore, purely data-driven approaches often struggle to comprehend the intrinsic chemical roles of discrete elemental identities, yet they excel at mapping continuous concentration gradients. Recognizing this distinction, we transform this combinatorial explosion into a targeted optimization problem by decoupling elemental selection from compositional ratio refinement. Ultrafast carbon thermal shock (CTS) is first employed to screen viable elemental combinations and establish an optimal quinary framework. Machine learning (ML) is subsequently applied to optimize compositional ratios within this reduced space, where statistical modeling efficiently navigates the remaining high-dimensional landscape. Targeting the oxygen evolution reaction (OER) as a proof-of-concept, our hybrid framework pruned the search space from over 10^10 possible compositions down into 13 systems, ultimately identifying high-entropy oxide (HEO)-Fe17.57Co28.45Ni31.27Mo10.57Zr12.14 as the optimal catalyst. The optimized high-entropy oxide exhibits an overpotential of 240 mV at 10 mA cm−2 and sustains stable operation at 1 A cm−2 for over 600 h in 1 M KOH. Mechanistic analysis reveals that Mo electronically tunes oxygen-intermediate adsorption, while Zr enhances structural robustness, collectively enabling high activity and durability. This work demonstrates that bridging discrete physical screening with continuous data-driven optimization provides an efficient and generalizable pathway for navigating high-dimensional material frontiers.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4369-1
Sodium-ion batteries (SIBs) are promising alternatives to lithium-ion batteries for large-scale energy storage due to sodium's abundance and low cost. Among cathode materials, polyanionic compounds like Na3V2(PO4)2O2F (NVPOF) offer high energy density and dual voltage plateaus at ~3.6 and 4.0 V, but suffer from low electronic conductivity and sluggish Na+ diffusion. Here, we report a dual-modulation strategy combining high-valence Nb5+ doping and polydopamine-derived carbon coating to synthesize Na3V1.94Nb0.06(PO4)2O2F-C (NVPOF-Nb-C) via a hydrothermal route. X-ray diffraction and Rietveld refinement confirm that Nb5+ doping induces slight lattice expansion without altering the tetragonal I4/mmm framework. Density functional theory calculations reveal that Nb5+ doping optimizes the crystal structure and reduces the Na+ diffusion barrier, while the uniform carbon coating enhances electron transport. Consequently, NVPOF-Nb-C exhibits remarkably improved electrochemical performance, including high reversible capacity, excellent rate capability, and ultralong cycling stability. In a full cell with hard carbon anode, it delivers a high energy density of 487.2 Wh kg−1 at 1C and retains 91.51% capacity after 3000 cycles at 20C. This work provides a synergistic strategy to overcome the intrinsic limitations of polyanionic cathodes for practical SIB applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4262-7
The escalating demands of artificial intelligence, machine learning, and neural computing necessitate multifunctional optoelectronic devices capable of integrating sensing, memory, and processing. Two-dimensional van der Waals heterostructures (vdWHs) offer unique advantages, yet their practical deployment is hindered by complex architectures and inefficient mode-switching. Here, we demonstrate a MoTe2/SnS2 anti-ambipolar heterojunction device enabling single-gate reconfiguration among frequency doubling, broadband photodetection, and neuromorphic computing. The device exhibits a peak-to-valley ratio (PVR) of 465, ensuring efficient frequency doubling. As a photodetector, it operates across an exceptionally broad spectral range of 520–2200 nm, with outstanding responsivity and detectivity. Furthermore, the device emulates complete synaptic behaviors, including short-term plasticity (STP), long-term plasticity (LTP), and paired-pulse facilitation (PPF). Integrated into a reservoir computing (RC) system trained on a vehicle motion dataset, it achieves a directional recognition accuracy of 98.7%. This work establishes a paradigm for multifunctional integration and low-power neuromorphic computing, advancing next-generation intelligent optoelectronic systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4315-2
High-temperature X-ray imaging demands scintillators with high crystallinity, efficient scintillation, and robust thermal stability, yet suitable materials remain scarce. Here, we report an ultra-high-crystallinity transparent glass-ceramic (GC) scintillator strategically designed via controllable heat-treatment-induced crystallization. A sequential precipitation method is employed, where cubic CaF2 nanocrystals initially form, subsequently promoting heterogeneous nucleation and growth of hexagonal BaAl2Si2O8. Intrinsic nanoscale phase separation into F-rich and O-rich domains significantly reduces atomic diffusion distances, yielding an unprecedented crystallinity of up to 97.6%. Notably, defect traps (oxygen vacancy defects, likely located within the lattice or at crystalline/amorphous interfaces) enable efficient carrier capture and thermally stimulated release, contributing to remarkable resistance to thermal quenching. Consequently, the GC scintillator maintains 90.6% of its integrated X-ray excited luminescence (XEL) intensity at 300 °C, with the integrated XEL intensity reaching 94.2% of commercial Bi4Ge3O12 (BGO) at room temperature. This enables stable high-temperature X-ray imaging with a spatial resolution of ~10.4 lp mm−1 up to 225 °C. This work provides a versatile pathway for developing high-sensitivity scintillators for extreme-environment X-ray imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4236-8
Electrochemical nitrate reduction (NO3RR) to ammonia offers a sustainable route for nitrogen recovery from wastewater, yet its efficiency is constrained by complex multi-step proton-electron transfers and competitive hydrogen evolution. Here, we report a series of binary cobalt-copper phosphates with precisely tuned Co/Cu ratios, revealing a volcano-type relationship between composition and catalytic activity. The optimized Co0.5Cu1.5(OH)PO4 catalyst, supported on a Ni3Co1OxHy/Ni foam substrate, achieves a Faradaic efficiency of 99.0% for ammonia at a high current density of 200 mA cm−2 in 1 M nitrate electrolyte, with a production rate of 9.18 mg h−1 cm−2 and sustained stability over 200 hours. In-situ ATR-FTIR spectroscopy and density functional theory calculations elucidate a tandem mechanism: Co sites promote water dissociation to generate active hydrogen (H*), while adjacent Cu sites facilitate nitrate adsorption and subsequent hydrogenation steps. This synergistic division of labor lowers the energy barrier for the rate-determining step, effectively suppressing HER and enhancing intrinsic kinetics. The work demonstrates that precise atomic-ratio engineering in dual-site transition metal phosphates provides a viable strategy to overcome activity-selectivity trade-offs in electrocatalytic nitrate-to-ammonia conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4212-x
Idiopathic pulmonary fibrosis (IPF) is a lethal interstitial lung disease with limited therapeutic options. Current treatments, such as nintedanib and pirfenidone, target downstream fibrosis but fail to address the upstream drivers, including persistent alveolar epithelial injury and abnormal repair. This study presents an inhalable, reactive oxygen species (ROS)-responsive liposomal system (SAB/GC-1@Lip-cRGD) that co-delivers the antioxidant salvianolic acid B (SAB) and the thyroid hormone receptor β (TRβ) agonist Sobetirome (GC-1). The liposomes are surface-modified with cRGD peptides for targeted delivery to fibrotic lesions and possess a negative surface charge to enhance mucus penetration. In the high-ROS fibrotic microenvironment, the liposomes destabilize, releasing SAB and GC-1. SAB scavenges ROS to remodel the fibrotic niche, while GC-1 reactivates TRβ signaling, driving the differentiation of stalled Krt8+ transitional epithelial cells into functional alveolar type I (AT1) cells. In a mouse model of pulmonary fibrosis, SAB/GC-1@Lip-cRGD significantly reduced pro-inflammatory cytokines (TNF-α, IL-1β, IL-6) and TGF-β1 in bronchoalveolar lavage fluid and lung homogenates. The proportion of CD206+ M2 macrophages decreased from 27.4% in the model group to 6.2% after treatment, indicating potent anti-inflammatory and anti-fibrotic effects. This synergistic strategy of microenvironment remodeling and epithelial regeneration achieved robust collagen depletion, restoration of alveolar integrity, and recovery of pulmonary function, outperforming single-drug or non-targeted formulations. The work provides a generalized paradigm for integrating microenvironment regulation with regenerative repair in pulmonary diseases.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4235-6
Fluorite-structured oxides (HfO2, ZrO2) are promising for resistive random-access memory (RRAM) due to their scalability and tunable properties. However, achieving high resistive switching on/off ratios remains challenging. Here, we report a collaborative strategy combining Hf/Zr ratio optimization and Lu3+ doping to regulate band structure and oxygen vacancy concentration in Hf0.4Zr0.6O2 (LHZO) thin films. The resulting LHZO devices exhibit a resistive switching ratio of 8.4 × 10^4, two orders of magnitude higher than that of ZrO2 (1.2 × 10^3). Electrical characterization and synchrotron radiation photoemission spectroscopy reveal that Lu doping widens the bandgap to 4.95 eV, downshifts the valence band, and introduces defect states, collectively suppressing p-type conductivity and reducing off-state leakage current. Simultaneously, Lu3+ doping enriches oxygen vacancies, stabilizing ohmic conductive filaments in the on-state. This co-optimization of band structure and oxygen vacancies effectively enhances insulating properties in the high-resistance state and ohmic conductivity in the low-resistance state, leading to superior resistive switching performance with robust retention (>10^4 s). Our findings establish a fundamental strategy for tailoring electronic properties of doped HfZrO2 thin films toward high-performance RRAM applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4176-y
Three-photon microscopy (3PM) in the near-infrared-III (NIR-III) window (1600–1840 nm) enables high-resolution visualization of cerebral vasculature in vivo, but its imaging depth and quality are limited by the performance of fluorescent probes. Here, we report a probe optimization strategy transitioning from mirror symmetry to centrosymmetry, yielding a highly symmetric aggregation-induced emission (AIE) molecule, T4PQ. The centrosymmetric structure aligns donor-acceptor units, promoting uniform electron cloud delocalization and directional charge transfer, which enhances exciton formation and suppresses non-radiative decay, thereby increasing fluorescence quantum yield. This symmetry also boosts the three-photon absorption cross-section by enhancing electron delocalization and transition dipole moment, enabling stronger nonlinear optical responses under long-wavelength excitation. T4PQ nanoparticles (T4PQ NPs) exhibit an enhanced three-photon absorption cross-section, high fluorescence quantum yield, and excellent photostability. In murine models, T4PQ NPs achieved three-dimensional cerebrovascular imaging at a depth of 1785 μm and real-time hemodynamic observation in microvessels at 1006 μm depth, with good biocompatibility. These results validate the advantage of centrosymmetric molecular design for deep-brain imaging probes, offering a high-performance tool for neurovascular research.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4180-9
Developing highly active and stable electrocatalysts based on the lattice oxygen mechanism (LOM) for the oxygen evolution reaction (OER) represents a significant challenge in water splitting. Herein, we successfully introduce oxygen vacancies (Ov) into high-entropy MnFeCoNiCu layered double hydroxides (HE-LDHs) via a solution chemical reduction method utilizing a defect engineering strategy. By precisely tuning the concentration of oxygen vacancies, we effectively activate the lattice oxygen within the HE-LDHs. The optimized Ov-rich high-entropy LDHs (Ov-HE-LDHs) exhibit excellent OER catalytic performance, achieving a current density of 10 mA cm−2 with a remarkably low overpotential of only 210 mV in 1.0 M KOH electrolyte, which is substantially superior to pristine HE-LDHs (315 mV) and commercial IrO2 (330 mV). Furthermore, the catalyst demonstrates outstanding long-term stability, capable of stable operation for 500 h at a high current density of approximately 200 mA cm−2. Advanced X-ray absorption fine structure analysis elucidates the lower metal valence states, indicating the existence of oxygen vacancies, while isotope labeling experiments and in-situ electrochemical Raman spectroscopy strongly confirm the successful activation of the LOM pathway. Density functional theory calculations further validate that the shift in the OER mechanism towards LOM and the resulting reduction in the reaction energy barrier are the fundamental reasons for the catalyst’s enhanced intrinsic activity. This work proposes a novel strategy for activating lattice oxygen in high-entropy LDHs through defect engineering, offering new insights and experimental guidance for the design and development of highly efficient and stable high-entropy OER electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4192-y
Electrochemical water splitting is pivotal for scalable green hydrogen production, yet its practical deployment hinges on cost-effective electrocatalysts with high activity and durability. This study introduces a low-cost, three-dimensional (3D) nanoporous ZrVFeCoNi material fabricated via chemical dealloying, at merely 0.16% of the cost of Pt. The structure-activity relationship between its microstructure and hydrogen evolution reaction (HER) performance was systematically explored. Lattice defect effects from multiphase intermetallic compounds, combined with multi-metal synergy, optimize H+ adsorption energy and electron transfer kinetics. The 3D nanoporous architecture provides a high electrochemical surface area with abundant active sites, enhancing electrolyte penetration and reducing interfacial mass transfer resistance. Consequently, the ZrVFeCoNi electrode exhibits outstanding HER performance, requiring only a 38 mV overpotential to reach 10 mA cm−2 and maintaining stable operation for 1000 h at 500 mA cm−2. Integrated into a full water electrolyzer (ZrVFeCoNi || IrO2/Ni), the system achieves a cell voltage of 1.60 V at a current density of 400 mA cm−2. Advanced characterization and density functional theory (DFT) calculations reveal that interfacial interactions and charge transfer at heterointerfaces drive catalytic activity, showcasing the potential of 3D nano-structured multiphase intermetallic compounds as high-performance electrocatalysts for green hydrogen systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4317-4
This correction addresses an image assembly error identified in Fig. 7a of the original article published in Science China Materials, volume 66, issue 6, 2023, pages 2513–2522. The error was confined to the assembly of images in Fig. 7a, which presents H&E staining analysis of major organs from a toxicity study. The corrected version of Fig. 7 is provided in this corrigendum. The original study evaluated the toxicity of lyophilized cabazitaxel (CTX) and Tween 80-based CTX formulations in CD-1 mice following a single intravenous administration of 30 mg kg−1 CTX via the tail vein on day 0, with sacrifice on day 14 for analysis (n=5). The figure includes H&E staining of major organs, complete blood count (CBC) analysis with statistical significance indicated by *p < 0.05, and mouse weight measurements. The correction does not affect the overall results, data interpretation, or scientific conclusions of the original article. All authors have reviewed and approved the content of this corrigendum. The authors sincerely apologize for any inconvenience caused to the editorial office, reviewers, and readers. The article was received on 6 May 2026, accepted on 4 June 2026, and published online on 31 July 2026.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4112-6
Radiostrontium remediation is crucial for ecological protection and sustainable development of nuclear energy. However, efficient removal of 90Sr from complex radioactive liquid waste, especially under acidic conditions, remains challenging due to material instability and intense proton competition. Herein, the rapid and highly selective capture of Sr2+ in neutral and even acidic solutions has been achieved by a layered potassium phosphatoantimonate KSbP2O8 with excellent radiation and thermal stability. Under neutral conditions, it possesses high maximum adsorption capacity (qmSr = 110.25 mg g−1), rapid adsorption kinetics (the removal rate (RSr) of 91.54% within 30 min), and excellent selectivity for Sr2+, and facile regeneration. Particularly, even under acidic conditions (pH 2.0), KSbP2O8 still maintains excellent Sr2+ removal capacity (qmSr = 79.38 mg g−1), fast kinetics, and high selectivity. A mechanism study by multiple characterizations reveals that the efficient Sr2+ removal of KSbP2O8 mainly stems from ion exchange between Sr2+ and interlayer K+ in KSbP2O8, which is attributed to the synergy between the Sb5+-induced Brønsted acidity and the high charge density of the anionic framework. This study demonstrates the exceptional capability of phosphatoantimonates to selectively capture Sr2+ under acidic conditions, highlighting the potential of phosphatoantimonates as effective scavengers for radiostrontium remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3696-3
The development of substitutable meniscus implants that can effectively protect articular cartilage remains a great challenge. Herein, a polyurethane with chemical crosslinking and sulfobetaine extenders containing hydrophobic chains (PU-CL-hSB) is developed, which could improve comprehensive properties and long-term stability simultaneously. By regulating the mole ratio of functional groups, PU-CL-hSB with appropriate mechanical properties, excellent tribological properties, and good fatigue resistance is used to prepare substitutable meniscus implant by hot-pressing. Due to the synergistic effect of functional groups, PU-CL-hSB meniscus implant presents comparable or even superior properties to native meniscus. It withstands a maximum force of 26.08 N versus 25.14 N for native meniscus, an energy dissipation from 45.93 to 39.17 N mm compared to 28.83 to 19.11 N mm for native meniscus over 300 cycles, and a friction coefficient from 0.08 to 0.19 compared to 0.11 to 0.26 for native meniscus. This PU-CL-hSB meniscus implant is further implanted into live rabbit knee joints for 8 and 25 weeks by a new approach, and in vivo data indicate that PU-CL-hSB meniscus implant not only protects articular cartilage from severe damage without eliciting inflammatory responses, but also can maintain normal physiological activities in the native state. Our findings present a substitutable meniscus implant that could be applied in vivo and propose evaluation methodologies for meniscus implants.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4197-4
Deep-blue organic light-emitting diodes (OLEDs) remain the most challenging primary-color emitters due to stringent exciton energy requirements. We strategically designed two innovative deep-blue emitters, SCZ-4AnCN and STPA-4AnCN, via systematic functionalization of an anthracene core with arylamino-decorated spirofluorene donors and cyano-substituted phenyl acceptors. Comprehensive theoretical and experimental analyses demonstrate that these spirofluorene-anthracene hybrids adopt precisely engineered distorted configurations, effectively suppressing detrimental intermolecular π–π stacking in condensed phases. The sp3-hybridized bridgehead carbons in spirofluorene units play a pivotal role by simultaneously restricting π-conjugation extension and fine-tuning donor–acceptor interactions, thereby stabilizing the lowest excited singlet (S1) state with dominant local excitation (LE) character. This molecular engineering yields exceptional deep-blue emission with remarkable efficiency. Notably, the materials exhibit unique high-lying reverse intersystem crossing (hRISC) behavior, enabling efficient triplet harvesting. Optimized doped devices incorporating SCZ-4AnCN achieve outstanding performance, including a maximum external quantum efficiency (EQE_max) exceeding 10% and CIE coordinates (0.154, 0.052) approaching the BT.2020 blue standard. Nondoped devices maintain impressive performance with an EQE_max of 7.51% and superior operational stability, demonstrating less than 10% efficiency roll-off at 1000 cd m−2. This work validates anthracene-based molecular architectures for deep-blue electroluminescence and establishes a transformative design paradigm for next-generation OLED emitters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4199-8
High-entropy borides (HEBs) represent an emerging class of high-entropy materials that have garnered significant attention as ultra-high-temperature ceramics (UHTCs). By leveraging the high configuration entropy effect, HEBs stabilize single-phase solid solutions, exhibiting a suite of properties unattainable in traditional binary borides. This review systematically consolidates research progress on HEBs, beginning with theoretical predictions and component design via first-principles methods. It then details typical HEB systems and principal synthesis techniques, including arc melting and spark plasma sintering. The core analysis evaluates the outstanding performance of HEBs, emphasizing exceptional mechanical properties such as ultra-high hardness and excellent fracture toughness, alongside high-temperature friction and wear behavior, and oxidation resistance. Finally, the review outlines application prospects in extreme environments like aerospace and cutting tools, while also addressing current challenges. The paper underscores the potential of HEBs to overcome the hardness-toughness trade-off inherent in conventional ceramics, driven by strong metal-boron hybridization. This comprehensive overview positions HEBs as promising candidates for next-generation thermal and mechanical protection systems, with future research directions focusing on optimizing compositions and processing to tailor properties for specific applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4397-4
The development of implantable bioelectronics faces critical trade-offs between mechanical compliance, electrical stability, and tissue adhesion. Here, we introduce ElHyX, a fully printable integrated system that combines ultrahigh stretchability, durable wet-tissue adhesion, strain-insensitive conductivity, and multimodal sensing-therapy feedback. The molecular covalent bonding design fundamentally eliminates the mechanical and electrical trade-offs of traditional soft conductive materials. Ex-vivo organ tests and long-term rodent implantation experiments verify stable working performance, favorable biocompatibility, and unique autonomous intervention capability. Specifically, the elastomer-hydrogel biphasic architecture achieves strain-insensitive conductivity with relative resistance changes below 5% over 1,000 cycles at 200% strain. The hydrogel component exhibits enhanced adhesion on porcine skin due to ionic crosslinks, maintaining performance after swelling. The integrated device enables closed-loop blood glucose management in diabetic rats, sensing glucose and heart rate to trigger vagus nerve stimulation for insulin modulation. Although unresolved problems exist in long-term in-vivo stability, wireless integration, and biodegradability, ElHyX provides a universal modular manufacturing framework for next-generation implantable bioelectronics. Further targeted optimization of material formulation, packaging technology, and closed-loop algorithms will accelerate industrialization and clinical translation of minimally invasive intelligent diagnostic and therapeutic implants.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3775-3
The urgent imperative for carbon-neutral chemical production has accelerated the development of solar-driven catalytic technologies that convert abundant C1 feedstocks (CO2 and CH4) into value-added C2+ molecules. Standalone photocatalysis remains constrained by rapid charge-carrier recombination and poor C–C coupling selectivity. This review critically examines multi-field-coupled catalysis—a transformative paradigm synergistically integrating solar energy with auxiliary thermal, electric, and magnetic fields. Through mechanistic dissection of photothermal, photoelectrochemical, and photomagnetic field cooperativities, it is summarized that thermal gradients attenuate phonon scattering to enhance charge-carrier drift mobility while vibrationally stabilizing reactive intermediates, electric potentials drive vectorial charge transport via Coulomb-force-directed separation and band alignment, and magnetic fields modulate spin-selective electron transfer through Zeeman splitting-mediated polarization to boost reaction specificity. This synergistic multi-field integration circumvents intrinsic limitations of single-mode photocatalysis by collectively reconfiguring reaction coordinates for selective C–C coupling. We further address persistent challenges in resolving ultrafast interfacial charge-transfer dynamics, scaling integrated field reactors for industrial deployment, and advancing in situ operando characterization of multiscale processes. Strategic research priorities are proposed to advance sustainable multi-field-coupled catalytic production of fuels and platform chemicals.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4153-2
Direct seawater electrolysis offers a promising route to green hydrogen production, circumventing freshwater scarcity. However, the presence of chloride ions (Cl−) poses severe challenges, including competing chlorine evolution reaction (CER) and corrosion of anode catalysts. Here, we report a dual-atom catalyst design, RuCr-Ni3P, where Ru atoms with strong chloride affinity and Cr atoms as Lewis acid centers are co-doped into a nickel phosphide matrix. This catalyst exhibits outstanding oxygen evolution reaction (OER) activity and selectivity in alkaline seawater, achieving stable operation for over 4000 hours at industrially relevant current densities. Mechanistic studies reveal that Cl− ions are selectively captured by Ru sites, forming a dynamic Ru–Cl coordination motif that electronically modulates adjacent Ni centers, promoting the formation of high-valent Ni>3+ species. This switches the OER pathway from the lattice oxygen mechanism (LOM) to the more efficient adsorbate evolution mechanism (AEM). Concurrently, Cr sites facilitate the formation of Cr–OH species, creating a localized alkaline microenvironment that further enhances OER kinetics. This dual-site synergistic mechanism transforms Cl− from a detrimental impurity into a beneficial chemical switch, concurrently enhancing both activity and stability. Our findings provide a paradigm shift in seawater electrolysis catalyst design, turning a longstanding challenge into an opportunity for efficient and durable hydrogen production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3709-4
Photoelectrocatalytic (PEC) detoxification of ofloxacin in hyposaline wastewater is hindered by weak built-in electric fields (IEF) and rapid charge recombination. Here, we report a crystal dipole engineering strategy using high-valence Mo-doped BiVO4 to enhance IEF and PEC activity. Mo incorporation breaks lattice symmetry, increasing the crystal dipole moment and amplifying IEF to 2.05 times that of pristine BiVO4. This promotes directional carrier migration, improving electron-hole separation efficiency. The optimized 4% Mo-BiVO4 photoanode achieves 96.5% ofloxacin degradation within 60 minutes and maintains 91.9% degradation efficiency in natural lake water containing saline and organic interferents, demonstrating exceptional anti-interference capability. This work provides a strategy for boosting photocatalytic performance through unit-cell dipole engineering, aiming to enhance sustainability in wastewater treatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3608-8
Polymeric carbon nitride (PCN) is a promising photocatalyst for H2O2 production due to its visible-light response, low cost, and high selectivity for the two-electron oxygen reduction reaction (ORR). However, its H2O2 yield is limited by narrow light absorption, low charge separation efficiency, and insufficient active sites. Here, crystalline poly(heptazine imide) (PHI)-based carbon nitride with highly dispersed In sites and N defects was prepared via an ionothermal method using LiCl/KCl molten salts. The large π-conjugated system and N defects enhance visible-light harvesting. Remaining K+ ions in nitrogen cavities act as interlayer electron channels, while N defects induce asymmetric charge distribution on the heptazine network, promoting interlayer and in-plane charge separation and transfer. In sites accelerate charge transfer dynamics and serve as active sites for ORR. The synergistic effect of metal modification and defect engineering boosts electron delocalization, significantly improving photocatalytic activity. The H2O2 production rate of 10InPHI reaches 15.3 mmol g−1 h−1 via a two-step single-electron ORR pathway, underscoring the potential of modified carbon nitride for efficient H2O2 photosynthesis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3803-8
The molecular copolymerization of donor-acceptor (D-A) interactions has been effectively utilized to modulate the charge transfer dynamics in polymeric carbon nitride (PCN) photocatalysts. Herein, a D-A configured photocatalyst (TPCN) was constructed by copolymerizing 4,4’,4’’-(1,3,5-triazine-2,4,6-triyl) trianiline (TAPT) as the electron donor with triazine units (electron acceptor). The unique propeller structure of TAPT, combined with the triazine framework, expanded the π-conjugated system and induced a strong built-in electric field (BIEF) across the D-A configuration. Theoretical calculations and transient absorption spectroscopy revealed that this synergistic effect facilitated intramolecular charge separation and widened the range of light absorption, indicating accelerated charge transfer and suppressed recombination in TPCN. The optimized TPCN3 sample exhibited dramatically enhanced photocatalytic H2O2 production (1.74 mmol g−1 h−1), representing a 13.4-fold increase over pristine PCN. Additionally, the TPCN3 sample also exhibited significantly faster degradation kinetics than PCN counterpart toward various emerging contaminants. This work demonstrates a promising strategy for designing efficient metal-free photocatalysts for sustainable H2O2 production and environmental remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3564-9
Sluggish water dissociation kinetics in the alkaline hydrogen evolution reaction (HER) hamper its practical production. Here, a heterojunction electrocatalyst featuring Ru-Ni(OH)2 interfaces on nickel foam (NF) with self-engineered built-in electric fields (BIEF) was synthesized via a simple in situ galvanic replacement reaction. The hierarchical Ru-Ni(OH)2/NF exhibits a record overpotential of 9.6 mV at 10 mA cm−2 for alkaline HER, surpassing most reported catalysts and commercial Pt/C. It also shows exceptional activity for hydrazine oxidation reaction (HzOR) at 100 mA cm−2 with a remarkably low potential of ca. 0.015 V vs. RHE. The assembled overall hydrazine splitting (OHzS) system integrating HER and HzOR requires a cell voltage of about 0.09 V to reach 50 mA cm−2, which is 1.637 V lower than the corresponding overall water splitting (OWS) device. Systematic analysis and calculation reveal that the BIEF induces redistribution of interfacial electrons for Ru, facilitating H2O dissociation and intermediate conversion, delivering ultra-high electrocatalytic performance. This work provides an avenue for design and preparation of electric field-mediated catalysts towards sustainable energy conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3585-1
Semiconductor-based surface-enhanced Raman scattering (SERS) substrates have attracted significant attention due to their high uniformity, reproducibility, stability, and cost-effectiveness. However, the Raman enhancement in semiconductors primarily relies on the chemical mechanism (CM), which typically results in a lower enhancement capability compared to traditional noble metals. In this study, we developed a novel two-dimensional (2D) SERS substrate, Ag2Te nanosheets (NSs), synthesized through a simple one-step redox reaction utilizing 2D Te NSs as the template. The 2D Ag2Te NSs not only exhibit strong interfacial interactions with molecules, thereby supporting the CM, but also possess quasi-metallic properties with low resistivity (2.8 × 10−4 Ω cm) and high density of free electrons (4.15 × 10^22 cm−3), giving rise to a significant visible-region surface plasmon resonance (SPR) band and contributing to enormous electromagnetic mechanism (EM). By synergizing CM and EM, the 2D Ag2Te NSs SERS substrate achieved an ultra-low limit of detection (LOD) of 10−10 M with an enhancement factor (EF) of 2.6 × 10^7 for methylene blue (MB), outperforming most semiconductors, even rivaling noble metals. The quasi-metallic properties of 2D Ag2Te NSs also benefit their sensitivity to multiple molecules. The accuracy and reliability were demonstrated in real-sample detections with recoveries of 91.5%–108.3% for various target molecules. These excellent performances, combined with remarkable cost-effectiveness, demonstrate the potential of 2D Ag2Te NSs as a practical SERS substrate with broad applicability. Furthermore, the inherent structural simplicity of these nanosheets creates significant opportunities for further sophisticated nanostructural engineering to advance the SERS performance in the future.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3615-1
Stretchable electronics are pivotal for bio-integrated devices, soft robotics, and wearables, yet their development is constrained by single-layer architectures that limit integration density and by mechanical mismatch between rigid components and soft substrates, which curtails service life. Here, we introduce a LEGO-like modular assembly strategy to construct multilayer three-dimensional (3D) stretchable electronics. Electronic components (ECs) and self-healing polyurethane (SPU) substrates patterned with liquid metal (LM) circuits serve as the modular blocks. This design simplifies fabrication and markedly enhances 3D integration density. The combination of LM circuits and self-healing elastic substrates enables devices to withstand diverse deformations and to autonomously heal after mechanical damage. Notably, the devices can undergo multiple recycling and reuse cycles without significant performance loss. This methodology offers a new paradigm for advanced flexible electronics, addressing critical bottlenecks in integration density, mechanical robustness, and sustainability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3553-7
Gesture interaction has emerged as a highly effective interface for intelligent human-computer interaction, attributed to its intuitive interaction modality and multi-dimensional control capabilities. However, traditional gesture interaction devices often depend on predefined encoding rules, which substantially limit interaction efficiency and degrade user experience. This study introduces an innovative intelligent finger ring interaction system based on a triboelectric nanogenerator utilizing PDMS/SrTiO3 composite thin film (PS-TENG). The system maps freehand writing gestures directly to textual information input, thereby eliminating the need for complex gesture encoding schemes and offering a user-friendly, low-learning-curve input method. By integrating a deep learning model, the system achieves recognition accuracies of 98.21% for English letters, 96.87% for Arabic numerals, and 96.44% for Chinese characters. Furthermore, it supports secure and encrypted data transmission and enables wireless interaction for gaming control. These findings indicate that the intelligent finger ring interaction system possesses significant potential for practical applications in information input and wireless control.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3645-3
Postoperative abdominal adhesion, a complication with morbidity exceeding 90%, imposes severe clinical and economic burdens. Existing bioadhesive barriers often exhibit unreliable adhesion to the slippery abdominal wall, risk mispositioning, and neglect frictional stimuli and inflammation. Inspired by the lubricated peritoneum, we developed a programmable adhesive dual-layer Janus patch (DJP) barrier integrating a lubricated layer and an adhesive matrix. DJP achieves rapid, noncovalent interfacial adhesion, subsequently enhanced 2.81-fold via covalent interactions, enabling repositioning within a short time window to improve surgical fault tolerance. The micron-scale poly(sulfobetaine methacrylamide) brush on the DJP surface provides hydration lubrication with a low coefficient of friction (0.06), mimicking peritoneal lubrication and reducing frictional damage to injured tissue. The catechol-containing copolymer confers antioxidative and anti-inflammatory properties, confirmed in vitro. In a rat model, DJP adhering to the injured site significantly reduced collagen deposition between the abdominal wall and cecum, preventing adhesion and promoting tissue healing compared to commercial barriers. This work provides a guiding reference for developing antiadhesive biomaterials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3432-8
This correction addresses an error in the labeling of author affiliations in the original publication (Sci China Mater, 2025, 68: 1561, DOI: 10.1007/s40843-024-3290-9). The corrected affiliations are as follows: Fuxia Huang, Feng Wang, Ya Liu, and Liejin Guo are affiliated with the International Research Center for Renewable Energy, State Key Laboratory of Multiphase Flow in Power Engineering, Xi'an Jiaotong University, Xi'an 710049, China. Yifei Liu is affiliated with the School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240, China. The correction was made upon the request of the authors and with approval from the respective institutions. The original article focused on crystal defects engineering of BiOI to enhance photocatalytic CO2 reduction to C2 products, a critical area for sustainable fuel synthesis. This correction ensures accurate attribution and institutional recognition, which is essential for research integrity and reproducibility. No changes were made to the scientific content or conclusions of the original study.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3623-y
Organic light-emitting diodes (OLEDs) are an advanced technology for full-color displays, yet the low efficiency of blue OLEDs remains a critical bottleneck. Here, we report a new strategy to design robust Pt(II) emitters with enhanced molecular rigidity and increased locally excited character. The resulting Pt(II) emitter exhibits an extremely narrow emission spectrum peaking at 458.6 nm with a full-width at half-maximum (FWHM) of 16.0 nm and a small Huang-Rhys factor of 0.278, together with a high photoluminescence quantum efficiency of 95%. When doped into an OLED, the device emits at 464 nm with high color purity (FWHM = 19 nm) and achieves high external quantum efficiencies (EQEs) of 32.6%, 29.4%, and 26.9% at luminances of 123, 1000, and 5000 cd/m2, respectively. Notably, the device attains a record-high maximum brightness of 84,895 cd/m2 among reported deep-blue OLEDs with Commission Internationale de l'Éclairage (CIE) y-coordinate < 0.15. This work demonstrates one of the highest-performing deep-blue OLEDs reported to date, addressing the dual challenges of efficiency and brightness in this spectral region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3677-9
The demand for high-performance scintillators in high-temperature applications, such as industrial flaw detection and oil exploration, necessitates materials with both high efficiency and thermal robustness. This work reports Tb3+-doped oxyfluoride glass scintillators exhibiting anti-thermal-quenching radioluminescence (RL). Three synergistic strategies were employed: (i) an oxyfluoride glass host providing a low-phonon-energy environment, (ii) increased structural densification of the glass network, and (iii) thermally enhanced energy transfer from Ce3+ to Tb3+. The resulting scintillators achieve an optical transmittance exceeding 88% at 542 nm, a record RL intensity of 350% relative to a standard Bi4Ge3O12 (BGO) crystal, and an imaging resolution of 24 lp mm−1. Notably, the RL intensity at 633 K reaches 143% of its room-temperature (303 K) value, demonstrating significant anti-thermal-quenching behavior. In contrast, commercial BGO and CsI:Tl scintillators exhibit RL intensities dropping to approximately 1% under identical conditions. These results establish the potential of Tb3+-doped glass scintillators for high-temperature X-ray imaging and provide a strategic framework for developing thermally robust scintillating materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3706-3
Aprotic lithium-oxygen (Li-O2) batteries are severely limited by slow cathode reaction kinetics and large polarization. Herein, we design and prepare a Mott-Schottky catalyst by uniformly embedding ultrafine Ru nanoparticles on nitrogen-doped carbon (Ru@NC) nanoflakes to accelerate oxygen redox kinetics of Li-O2 batteries. The Mott-Schottky effect of Ru@NC drives spontaneous electron rearrangement in the NC matrix and induces a strong built-in electric field at heterointerfaces, which accelerates the activation and conversion of oxygen intermediates. The obtained Ru@NC possesses rich Mott-Schottky heterointerfaces and defective carbon structures, which provide extensive adsorption and nucleation sites. More importantly, Ru@NC manifests moderate affinity for the intermediate LiO2, inducing formation of unique nanosheet-like Li2O2 with low Li2O2/cathode interfacial impedance, which further enhances oxidation kinetics. These enable the Li-O2 battery with Ru@NC to deliver a remarkably reduced polarization of 0.89 V, superior rate performance, and prolonged lifespan of over 200 cycles. This work will provide valuable guidelines for engineering advanced electrocatalysts for high-performance Li-O2 batteries and beyond.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3746-x
The polyanionic compound Na3V2(PO4)2O2F (NVPOF) possesses a stable three-dimensional framework, high theoretical specific capacity, and favorable operating voltage, yet its sluggish Na+ diffusion kinetics and low electronic conductivity impede industrial application. This study proposes a dual regulation strategy combining carbon coating and heat treatment temperature to synergistically enhance crystallinity and electrochemical performance. NVPOF@C-400 and NVPOF@C-600 were synthesized via in-situ dopamine hydrochloride coating followed by heat treatment at 400 °C and 600 °C, respectively. Carbon coating at 600 °C significantly improved crystallinity and increased electronic conductivity by three orders of magnitude through the carbon layer's conductive network. The ~4.5 nm carbon layer effectively suppressed abnormal grain growth and secondary crystallization aggregation at high temperatures, maintaining uniform particle size of approximately 0.36 μm, which shortens Na+ diffusion pathways and prevents ion transport obstruction. Consequently, NVPOF@C-600 delivered a high discharge capacity of 102.5 mAh g−1 at 20 C and retained 96.5% capacity after 10,000 cycles. In a full-cell configuration with hard carbon (HC), NVPOF@C-600//HC achieved an impressive 89.3% capacity retention after 9,000 cycles. This work provides critical insights for practical implementation of high-performance NVPOF cathodes in sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3506-3
Metallic glasses (MGs) often suffer from sluggish hydrogen evolution reaction (HER) kinetics in neutral and alkaline media, with their catalytic performance predominantly confined to acidic environments. Herein, we reported a novel thermoplastic forming technique to fabricate a self-supported partially crystallized nanoporous Pt56.2Ni5.2Cu16.8P21.8 metallic glass (C-NPMG). The C-NPMG catalyst delivers ultralow overpotentials of 18.0 mV (0.5 M H2SO4), 42.2 mV (1 M KOH), and 88.0 mV (1 M phosphate-buffered saline (PBS)) at a current density of 10 mA cm−2, outperforming most state-of-the-art non-noble MGs and Pt-based benchmarks across all pH conditions. Notably, it maintains negligible performance decay for over 1000 h in alkaline electrolytes, showcasing superior stability. Experimental and computational analyses reveal that the enhanced HER activity arises from three synergistic effects: (1) the high-specific-surface-area nanoporous architecture that maximizes active site exposure; (2) the formation of crystallite-amorphous interfaces during partial crystallization, which lowers the energy barrier for H2 desorption; (3) the hierarchical super-hydrophilic and super-hydrophobic wettability of the C-NPMG, which optimizes mass transport and prevents electrolyte-induced corrosion. This work establishes a novel design paradigm for developing high-performance, pH-universal HER electrocatalysts by integrating structural nano-engineering and crystallite-amorphous phase synergy in metallic glass systems to overcome the trade-offs between performance and stability in electrochemical water splitting.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3695-8
Sulfur-based lithium-ion batteries, particularly those employing sulfurized poly(acrylonitrile) (SPAN) cathodes and graphite (Gr) anodes, offer high theoretical capacity and low cost but suffer from temperature-dependent capacity decay. This study systematically investigates the electrochemical dynamics and capacity decay mechanism of SPAN||Gr pouch cells cycled at 25–55 °C. Multiscale analyses reveal that capacity fade arises from active lithium loss and increased resistance, both accelerated by higher temperatures. Active lithium loss is primarily attributed to dead lithium formation and thickening of the solid electrolyte interphase (SEI) and cathode electrolyte interphase (CEI), while resistance increase is predominantly due to SEI/CEI thickening. As temperature rises, active lithium loss becomes the dominant decay factor. Leveraging the consistent decay mechanism across temperatures, an accelerated aging model based on the Arrhenius equation is developed: y = 0.9x + a. This model accurately predicts cycling parameters at specific temperatures and reduces testing time by 50% when extrapolating from 55 °C to 25 °C. These insights provide critical guidance for developing long-life sulfur-based batteries for practical energy storage applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3652-2
Existing robotic end-effector gripping technologies often encounter challenges such as poor adaptability to environmental changes, incomplete deformation sensing, and insufficient adhesion stability, which can compromise operational safety and reliability. Here, we present the bio-inspired self-sensing suction cup, in which the core self-sensing capability is achieved by combining high-performance, laser-induced graphene/Ag NWs flexible sensors with a Wheatstone bridge design. The flexible sensors provide high sensitivity, while the Wheatstone bridge circuit enables accurate and stable detection of deformation during the gripping process. Integrated into the octopus-inspired suction cup, this system allows for real-time monitoring of deformation and adsorption stability. The self-sensing suction cup demonstrates good performance across a 0–25 kPa negative pressure range, with outstanding linearity (R2 = 0.993) and high sensitivity (GF = 10.436 kPa−1). Experimental results confirm that the suction cup can achieve stable adsorption under varying loads and enable real-time monitoring of the suction cup status during the gripping process. This design provides a promising solution for intelligent gripping systems, logistics, and object recognition in challenging environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3649-0
Injectable hydrogels formed via dynamic chemical crosslinks hold great promise as drug delivery platforms due to their robust yet adaptable nature, stimuli-responsiveness, and tunable structures and properties. However, their inherently high water content poses a significant challenge for the efficient encapsulation and sustained release of hydrophobic drugs. Here, we present a novel injectable hydrogel system constructed via a strain-promoted disulfide-thiol exchange between dithiolane-functionalized polymer strands and thiolated core-shell nanoparticles (NPs) under physiological conditions. The hydrophobic core and hydrophilic shell structure of the NPs enables effective loading and protection of hydrophobic drugs, while rapid gelation occurs upon mixing the thiolated NPs with dithiolane-polymers in phosphate-buffered saline. The hydrogel shows excellent injectability, self-healing capability, in vitro biodegradability, and cytocompatibility. This hydrogel system enables sustained release of hydrophobic drugs over 32 days in aqueous media and supports sequential dual-drug release. Its redox-responsiveness under tumor-mimicking reducing conditions, enabled by the disulfide crosslinks, further facilitates controlled intracellular drug release. This multi-component platform offers a versatile strategy for designing advanced injectable hydrogels with potential applications in hydrophobic drug delivery and other biomedical fields.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3789-x
Wearable sensors have attracted significant attention due to their superior sensitivity, safety, and adaptability compared with conventional detection technologies. However, developing sustainable sensing materials that combine excellent performance with environmental friendliness remains a significant challenge. In this study, Juncus effusus (JE), a natural fiber featuring a unique internal three-dimensional (3D) network structure, was employed as the substrate. Conductive polyaniline was loaded onto the JE structure to impart electrical conductivity, and Ecoflex encapsulation provided high elasticity. Based on this approach, a JE-based resistive flexible sensor (PHE-JE) was successfully fabricated. The PHE-JE sensor exhibits high stability under various strain conditions, along with excellent flexibility and durability. Moreover, benefiting from its complex 3D structure and synergistic material interactions, the PHE-JE sensor enables accurate detection of diverse motion types, showing promising potential for future wearable sensing applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3586-7
Ischemic stroke is a leading cause of mortality and long-term disability worldwide, with endovascular stent intervention emerging as a key therapeutic strategy. Biodegradable Mg-Zn-Y-Nd alloy (ZE21B) offers promising mechanical properties and biocompatibility for vascular scaffolds, yet suffers from inadequate corrosion resistance, insufficient endothelialization, and impaired blood-brain barrier remodeling. This study develops a composite coating comprising barnacle cement protein cp19k and sulfonated hyaluronic acid nanoparticles (NP@S-HA) applied via electrostatic spraying onto ZE21B. The cp19k/NP@S-HA coating enhances corrosion resistance by approximately 40.6% relative to uncoated ZE21B, as determined by electrochemical and static immersion tests. In vitro blood and cellular assays demonstrate that the coating promotes endothelial cell proliferation and migration, inhibits smooth muscle cell proliferation while regulating contractile phenotype, suppresses macrophage adherence and induces M2 polarization, reduces TNF-α expression, and mitigates fibroplasia. These findings indicate that the cp19k/NP@S-HA composite coating provides an effective surface modification strategy for biodegradable magnesium alloys in cerebrovascular applications, potentially improving stent performance and patient outcomes.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(25)61036-5
Large graphene oxide (LGO) sheets offer significant advantages over smaller ones in various applications, yet their production via Hummers-type oxidation of large natural graphite flakes remains challenging due to difficulties in achieving full oxidation and avoiding fragmentation. This study provides the first direct evidence that large graphite flakes (up to 1 mm) can be completely oxidized without fragmentation under static conditions, as revealed by in-situ monitoring. The oxidation process is governed by diffusion of the oxidizer between layers, described by Fick's law, where a high oxidizer concentration gradient increases the diffusion rate. By minimizing the amount of concentrated H2SO4 solvent, we achieved a semi-solid state that elevates oxidizer concentration, facilitating Mn(VII) diffusion and enabling complete oxidation of gram-scale large flakes with significantly reduced reagent consumption. Reaction temperature was optimized to balance graphite oxidation and Mn(VII) self-decomposition. Using this approach, 200-, 100-, and 50-mesh natural graphite were fully oxidized with reduced H2SO4 and KMnO4 usage. After exfoliation, LGO with average lateral sizes of 27.3, 58.7, and 116.2 μm were obtained, respectively, with 100% conversion and yield over 165%. This work not only provides a scalable, cost-effective strategy for LGO production but also advances the fundamental understanding of Hummers-type oxidation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3757-2
β-Ga2O3 is a promising candidate for solar-blind ultraviolet photodetection owing to its suitable bandgap of approximately 4.9 eV, excellent photoresponse characteristics, and high stability. However, the lack of a sufficient driving force within the material leads to extensive bulk charge recombination, limiting its photocurrent and thus posing significant challenges in designing high-performance Ga2O3-based photodetection. In this study, we propose a gradient doping strategy to achieve a Sn-doping concentration gradient along the β-Ga2O3 film thickness. By combining sol–gel synthesis with rapid thermal annealing, a spatially graded band structure with a full-space built-in electric field is constructed, which increases the width of band bending over a large region and is crucial for significantly enhancing carrier separation and transport in the bulk. The resulting gradient Sn-doped β-Ga2O3 enables exceptional photoelectric performance without an external bias under 254 nm irradiation, including a superior responsivity of 66.88 mA W−1, a high detectivity of 8.12 × 10^11 Jones, and a fast rise/decay time of 79/65 ms, outstanding most existing similar reported photoelectrochemical (PEC) type optoelectronic devices. Additionally, the device exhibits excellent long-term stability and enables high-resolution underwater ultraviolet imaging. This study demonstrates that the gradient doping strategy provides a feasible approach for enhancing the PEC performance of β-Ga2O3 photoelectrodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3708-y
Polar two-dimensional (2D) perovskites, with their excellent semiconductor properties, intrinsic anisotropy, and bulk photovoltaic effect, have emerged as promising candidates for self-driven polarization-sensitive photodetectors. However, these self-driven polarized detectors typically require fabrication along the spontaneous polarization direction to maintain device operation in the self-driven mode, which imposes additional limitations. Herein, we demonstrate multidirectional self-driven polarization-sensitive photodetection by constructing 2D perovskite-based asymmetric contact devices, Ag/2D perovskite/C. The built-in electric field, originating from the difference in work functions, acts as the driving force for the separation and transport of photogenerated carriers. Notably, this approach does not necessitate a specific direction, thereby enabling multidirectional self-driven photodetection. Under excitation by linearly polarized light, our devices exhibit impressive polarization-sensitive discrimination in multiple directions, achieving polarization ratios of 3.3 and 3.1 along the a and b-axes, respectively. Our work enriches the approaches enabling self-driven polarization-sensitive photodetection, free from the previous limitations.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3748-9
Direct regeneration is a sustainable solution for recycling spent lithium-ion batteries (LIBs), yet the irregular strains induced by the irreversible FePO4 phase after cycling hinder Li+ replenishment in spent LiFePO4 cathodes. This study proposes a lattice stress modulation strategy that reduces FePO4 to Fe2P2O7, reducing unit cell volume from 271.7 to 122.6 Å3, releasing residual stress and reconstructing continuous Li+ transport channels. The phase transformation reconstructs FeO6 octahedra, lowering the migration energy barrier for ions. This synergistically weakens steric effects, facilitating Li+ replenishment and eliminating Li-Fe anti-site defects. Regenerated LiFePO4 cathodes achieve 80.2% capacity retention after 1000 cycles at 2C, outperforming commercial cathodes. The work establishes fundamental principles for the pre-treatment stage of direct regeneration and provides a paradigm-shifting solution for sustainable LIB recycling.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3807-8
Electrocatalytic co-reduction of CO2 and nitrate offers a sustainable route for urea synthesis, valorizing nitrogenous waste and CO2. However, achieving high-performance urea electrosynthesis under ambient conditions remains challenging due to the need for simultaneous activation of CO2 and efficient H2O dissociation to supply active *H for *NOx hydrogenation, ultimately forming key C- and N-containing intermediates for C–N coupling. Here, we report a bifunctional Pd-single-atom-modified Cu (Pd1Cu) nanorod catalyst that synergistically promotes adsorption and stepwise activation of CO2 and H2O, steering the reaction pathway toward selective urea synthesis. Integrating experimental evidence, in situ spectroscopy, and computational analyses, we disclose that atomically dispersed Pd sites kinetically favor co-generation of *CO and *NH2 via H2O dissociation-driven proton transfer, forming an optimal intermediate balance. The dual metal active sites enhance C–N coupling via combined electronic and geometric effects, substantially lowering the reaction energy barrier and improving selectivity. This work provides a rational design strategy for advanced multifunctional catalysts for urea electrosynthesis, contributing to carbon neutrality and waste nitrogen valorization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3805-1
The sluggish kinetics of oxygen reduction and evolution reactions (ORR/OER) at the air electrode impede the practical deployment of fiber zinc-air batteries (FZABs) for wearable electronics. Conventional bifunctional catalysts suffer from an inherent activity trade-off due to the distinct mechanisms of ORR and OER. Here, we propose a spatial decoupling strategy to overcome this limitation by engineering isolated Fe single atoms and Fe–Ir dual-atom pairs on a nitrogen-doped carbon matrix (Fe/FeIr-NC). In this architecture, Fe single atoms serve as ORR centers, while Fe–Ir pairs with tunable spacing are tailored for OER, enabling complete functional separation and independent optimization. The catalyst exhibits an ORR half-wave potential of 0.91 V and an OER overpotential of 250 mV at 10 mA cm−2, yielding a record-low bifunctional gap (ΔE = 0.57 V) that outperforms all reported single- and dual-atom catalysts. A flexible fiber zinc-air battery based on this catalyst delivers a peak power density of 3920 W kg−1, along with a 1.4-fold increase in energy efficiency and a 2.6-fold extension in cycle life compared to the commercial Pt/C + IrO2 benchmark. This work not only breaks the traditional activity trade-off in bifunctional catalysis but also offers a promising route toward high-performance power sources for wearable electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3815-0
The development of bifunctional electrocatalysts capable of integrating biomass-derived platform molecule oxidation with organic reduction offers a promising strategy for simultaneously enhancing energy efficiency and generating high-value chemicals. However, designing catalysts that exhibit both high activity and stability in integrated systems remains a significant challenge. Herein, we report a self-supported electrode composed of nitrogen-doped carbonized wood (NCW) supported NiCo nanosheets (NiCo 0.3/NCW) that enables the electrocatalytic 5-hydroxymethylfurfural oxidation to produce 2,5-furandicarboxylic acid (FDCA) and the nitrobenzene reduction to yield aniline in an integrated electrochemical cell. The NiCo 0.3/NCW electrode achieves the production of FDCA and aniline at a low cell voltage of 1.7 V, with ~99% anodic and ~92% cathodic Faradaic efficiencies, respectively. Experimental characterizations disclose that the hierarchical porous NCW architecture promotes the dispersion of active sites, while nitrogen doping strengthens metal–support interactions. In-situ spectroscopic experiments combined with density functional theory (DFT) calculations reveal that cobalt incorporation tunes the electronic structure of nickel, thus optimizing substrate and intermediate adsorption, and lowering energy barriers. These effects ultimately enhance the performance of the natural wood-derived catalyst in integrated biomass valorization and selective organic electrosynthesis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3713-y
Layered double hydroxides (LDHs) are promising electrocatalysts for the oxygen evolution reaction (OER), yet their practical application remains limited by poor electrical conductivity and sluggish reaction kinetics. In this work, we synthesize three high-entropy LDHs (HELDHs) featuring a hierarchical architecture of microspheres assembled from ultrathin nanosheets, via a simple hydrothermal method using a combination of low-cost, catalytically active transition metals (Fe, Co, Ni, Mn, Zn, Cu, and Cr). Among them, the FeCoNiMnZn HELDH exhibits outstanding OER performance, requiring an overpotential of only 306 mV to reach a current density of 100 mA cm−2. Notably, during 200 h of continuous operation, the device exhibits a stable and, in some cases, increasing current output. This exceptional activity is attributed to the formation of abundant cation vacancies, induced by Zn leaching, which enhance the intrinsic catalytic properties by optimizing the adsorption energies of key OER intermediates. Density functional theory calculations further validate that these vacancies modulate the electronic structure and lower reaction barriers, underscoring the effectiveness of cation-vacancy engineering in high-entropy systems for efficient and durable water oxidation catalysis. The optimized catalyst was further evaluated as the air cathode in a zinc–air battery, demonstrating practical electrochemical performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3725-1
Conductive hydrogel-based stretchable electronics have been extensively investigated, with strain sensors being the most prominently studied. While mechanical properties significantly affect device performance, the systematic correlation between specific mechanical parameters and sensing performance remains rarely explored. This work compares the influences of Young’s modulus and mechanical hysteresis on sensing performance between highly entangled PAM-Li and double-network PAM-Li-Agar-3 strain sensors. Owing to the brittle agar network, which imparts a higher Young’s modulus and pronounced mechanical hysteresis to the double-network PAM-Li-Agar-3 hydrogel, the corresponding sensor requires a greater driving force for deformation and yields signals with poor reproducibility. In contrast, the PAM-Li hydrogel, characterized by highly entangled polymer chains, exhibits a lower Young’s modulus and negligible mechanical hysteresis. Consequently, signals from the PAM-Li strain sensor demonstrate enhanced sensitivity and stability. Therefore, this work demonstrates that a low Young’s modulus and minimal mechanical hysteresis are critical factors for achieving superior sensing performance in strain sensors, as systematically validated through comparative analyses across diverse application scenarios.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506081
Advanced oxidation processes (AOPs) are promising for degrading organic pollutants in water treatment. Heterogeneous catalytic ozonation (HCO) has gained attention due to its high oxidation efficiency, strong interference resistance, and low secondary pollution. In this study, a series of trimetallic-carbon composite ozone catalysts were prepared via an organic precursor calcination method using γ-Al2O3 as support. This method enhanced catalytic activity and mechanical strength while overcoming the limitations of carbon materials (low mechanical strength) and metal-based materials (poor mass transfer). The optimized catalyst, CA-FeCoCu, comprising Fe, Co, Cu, carbon, and alumina, exhibited excellent performance in phenol degradation and real industrial wastewater treatment. Characterization revealed that the synergistic effect of trimetals and the introduction of multiple carbon types increased specific surface area and hydroxyl radical (·OH) generation. In a pilot-scale fixed-bed reactor, the CA-FeCoCu/O3 system reduced COD from 120 mg·L−1 to below 40 mg·L−1, with an O3 consumption ratio (O/C) of less than 1, effectively lowering operational costs. This work provides a new strategy for developing efficient and stable heterogeneous O3 catalysts and offers a reference for the practical application of HCO in industrial wastewater treatment.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506019
Acidic in-situ leaching of sandstone-type uranium deposits leaves residual acid and uranium in groundwater, posing environmental risks. This study investigated the feasibility of loading hydroxyapatite (HAP) onto aquifer sandstone particles for in-situ remediation. Sandstone particles were collected from an aquifer and reacted with a HAP-generating solution for 52 days to produce sandstone/HAP composite. Batch experiments examined the effects of initial pH, initial uranium concentration, composite dosage, and interfering ions on uranium removal. Results showed successful HAP loading on sandstone surfaces. At initial pH 3, uranium concentration 5 mg/L, composite dosage 3 g/L, and 24 h reaction, uranium removal reached 95.6%. Interfering ions suppressed removal in the order Fe3+ > Mn2+ > Ca2+ > Mg2+ > SO4^2-. Removal mechanisms included electrostatic adsorption, ion exchange, and dissolution-reprecipitation, with good stability of immobilized uranium. This work validates the concept of in-situ HAP loading in aquifers and provides a basis for practical application in acidic uranium-contaminated groundwater remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3912-0
This erratum corrects an error in the Chinese name of co-first author Tianxiao Xiao (肖天孝) as originally published in the article 'A multi-modal smart chest patch for real-time cardiopulmonary monitoring and anomaly detection' (Sci China Mater, 2025, 68(12): 4413–4422). The corrected Chinese name is 肖天笑. The correction applies solely to the author's name and does not affect the scientific content, experimental data, or conclusions of the original paper. The authors and publisher apologize for any inconvenience caused.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506041
Urban and rural multi-source organic waste faces bottlenecks including high compositional heterogeneity, single resource recovery pathways, and uneven product quality. In the Taihu Lake region, active tourism and catering, high greening, and dense water networks generate large volumes of diverse waste with high moisture content, exacerbating these issues. This study evaluated a coupled bio-drying and aerobic composting process at a demonstration center in Linhu Town, Suzhou, Jiangsu Province, employing a three-stage control strategy: gradient dewatering, high-temperature stabilization, and maturation enhancement. Continuous operation showed that kitchen waste moisture content decreased from 77.70% to 58.69% after 1 day of bio-drying, to 23.22% after 7 days of silo reactor composting, and to 17.70% after at least 20 days of maturation. The aerobic composting phase maintained temperatures above 55°C for over 5 days, reaching a maximum of 68.1°C, meeting the harmless treatment requirements of CJJ 52—2014. After 20 days of maturation, the organic fertilizer product had an electrical conductivity below 4.00 mS·cm−1, organic matter content of 51.22%, total nutrient content of 5.61%, and heavy metal concentrations below the limits of NY/T 525—2021. The results provide technical support for efficient treatment and resource utilization of urban and rural organic waste.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507021
The accumulation of heavy metals in soil around municipal solid waste landfills poses potential risks to human health. This study selected a municipal solid waste landfill and monitored the concentrations of eight heavy metals (Zn, Pb, Cd, Ni, Hg, Cu, As, Cr) in surrounding soil. The geo-accumulation index method was used for pollution assessment, and a health risk assessment model recommended by the USEPA, combined with Monte Carlo uncertainty analysis, was employed to evaluate the pollution status and health risks to nearby residents. Results showed that among the eight metals, Pb, Ni, and Cd exceeded risk screening values at 4.26%, 6.38%, and 4.26% of sampling points, respectively. Geo-accumulation indices indicated overall clean conditions (mean < 0), but slight pollution by Pb, Zn, Ni, Hg, and Cd at some points. Probabilistic risk assessment based on Monte Carlo simulation revealed that for both adults and children, the cumulative non-carcinogenic risk was negligible, while carcinogenic risk was acceptable. However, there was a very low probability (approximately 0.2%) of non-carcinogenic risk for children, and probabilities of unacceptable carcinogenic risk were 0.64% for adults and 3.21% for children. Nickel was the primary contributor to carcinogenic risk, and children faced higher health risks than adults. These findings provide a reference for pollution prevention and health risk management of soil around municipal solid waste landfills.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506020
The rotary kiln roasting of lepidolite for lithium extraction faces challenges of unstable lithium conversion rates and high energy consumption. To address this, a multi-objective optimization method coupling improved neural network simulation with a multi-objective genetic algorithm was proposed, targeting the synergistic optimization of lithium conversion rate (TRLi) and natural gas consumption intensity (EIng). Using long-term industrial time-series data of batching parameters and kiln operating variables, back-propagation (BP) neural network and its particle swarm optimization (PSO) improved variant were developed to model TRLi and EIng. The PSO-BP model demonstrated superior accuracy in capturing the complex nonlinear relationships, reducing mean absolute percentage errors (MAPE) to 0.278 and 0.284 for TRLi and EIng, respectively. Subsequently, the non-dominated sorting genetic algorithm II (NSGA-II) was employed to construct a multi-objective optimization model, yielding a Pareto-optimal set of process parameters that maximize TRLi and minimize EIng. The results revealed that under NSGA-II optimized conditions, TRLi could be stabilized between 82.45% and 87.96%, an average increase of 3.61 percentage points over baseline operations, while EIng could be reduced to 53.7 m3 per ton of clinker. For an annual processing capacity of 3.2×105 tons of lepidolite concentrate and sulfate mixture, this corresponds to an additional 127.1 tons of lithium metal recovery, a reduction of 1,964,912 m3 in natural gas consumption, and a decrease of 3,763.84 tons in CO2 emissions annually. This study provides theoretical and technical support for the green, high-quality, and low-carbon supply of critical raw materials for the lithium battery new energy industry.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507032
To mitigate global warming, regional carbon neutrality pathways are critical. Based on the Guangdong Energy Policy Simulator (EPS) model, this study simulates total energy consumption and greenhouse gas (GHG) emissions under baseline, Carbon Neutral 60 (CN60), and Carbon Neutral 50 (CN50) scenarios, and analyzes the emission reduction effects and costs of various energy policies. Results show that by 2060, total energy consumption under CN60 and CN50 decreases by 39% and 44% relative to baseline, respectively. Primary electricity and other energy, natural gas, oil, and coal account for 56%, 26%, 14%, and 4% under CN60, and 60%, 24%, 13%, and 3% under CN50. GHG emissions under CN60 drop to 80×10^6 tCO2e by 2060, an 89% reduction from 2020; under CN50, emissions reach 92 and 55×10^6 tCO2e in 2050 and 2060, respectively, reductions of 87% and 92% from 2020. Policies such as increasing clean electricity share, industrial electrification (hydrogen), increasing green power purchases, building electrification, F-gas reduction, and improving industrial energy efficiency standards show significant reduction effects, with clean electricity share being the primary source. Policies like improving industrial energy efficiency standards, increasing industrial product utilization, and increasing clean energy vehicle market penetration are cost-effective; increasing clean electricity share, green power purchases, building electrification, and F-gas reduction effectively balance reduction effects and costs. Industrial electrification (hydrogen) contributes >5% cumulative reduction but faces economic challenges for full-scale promotion in the short term; industrial carbon capture and storage and electrolytic hydrogen contribute <2% cumulative reduction with high costs. Therefore, Guangdong should prioritize cost-effective policies, promote balanced policies, gradually optimize energy structure, achieve clean electricity, and foster green industrial transformation to achieve carbon neutrality at lower economic cost.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60600-1
The service life of refractory bricks in the slag tapping hole of entrained-flow gasifiers is a critical bottleneck for long-term stable operation. This study investigated the damage mechanism of high chromia refractories in four commercial coal-water slurry gasifiers by analyzing gasification coal samples and corroded refractory bricks. Slag characteristics, including crystallization and viscosity-temperature behavior, were evaluated. Results revealed that low-viscosity slag induces more severe refractory damage. To mitigate slag crystallization risk, a safe slag tapping temperature range is recommended as tICT−t2.5 when tICT exceeds t25. Interior morphology of corroded bricks exhibited cracks, primarily attributed to molten slag penetration and subsequent reactions with refractory material. SEM-EDS analysis of slag-aggregate and slag-matrix interfaces identified reduction in Cr2O3 content as the earliest damage characteristic. XRD detected no zirconium-containing spinel in cracks, indicating that thermal expansion mismatch between newly formed phases and the refractory matrix drives crack propagation. A damage mechanism is proposed: initial Cr2O3 depletion compromises both matrix and aggregate, facilitating slag ingress and new phase formation, ultimately leading to structural failure. Early detection or prevention of Cr2O3 reduction is essential to prolong refractory service life.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60581-0
Lignin-derived oxygenated aromatics, particularly phenols and aromatic ethers, are promising feedstocks for synthesizing high-density, high-heat-sink aviation fuels via alkylation-hydrogenation processes. This study systematically evaluates the catalytic performance of various zeolites (Hβ, HZSM-5, MCM-41, and HUSY) in the alkylation of phenol with cyclohexanol. Characterization demonstrates that HUSY zeolite exhibits superior catalytic activity due to its favorable pore architecture and well-balanced acid site distribution, which synergistically facilitate molecular diffusion and catalytic transformations. To further enhance catalytic properties, HUSY was modified with citric acid at various concentrations and compared with NaOH and oxalic acid treatments. Results reveal that citric acid treatment preserves crystallinity while modulating acidity and pore structure. All modified zeolites enhance phenol alkylation activity. Notably, HUSY-0.5M, exhibiting the highest medium-strong acid to total acid ratio, achieves superior performance: 80.4% phenol conversion and 99.6% selectivity for alkylation products. The catalyst also shows high activity for various lignin-derived compounds (p-cresol, anisole, guaiacol), demonstrating broad applicability. This work provides a new strategy for valorizing lignin-derived phenols into high-value fuel precursors through alkylation.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0024
This study investigates the thermochemical conversion behavior of microalgae pellets in a molten hydroxide salt (80% NaOH-20% Na2CO3) system and its influence on hydrogen production. By comparing temperature evolution, gas release characteristics, and structural evolution of pellets with and without molten salt, and integrating char alkalization experiments, the regulatory mechanism of molten salt on reaction pathways and hydrogen production was systematically analyzed. Results indicate that molten salt significantly enhances internal heat transfer efficiency, achieving a central heating rate of 177 °C/s, effectively alleviating thermal hysteresis. Concurrently, molten salt promotes pore development through penetration, erosion, and catalytic effects, resulting in a porosity increase of 53.2%–104.3% after 10 s of reaction. Conversion efficiency is markedly improved, with the dominant reaction pathway shifting to char alkalization after only 70 s. Furthermore, when heating rate is increased above 600 °C, hydrogen yield from char alkalization improves more significantly, primarily attributed to the synergistic promotion of molten salt catalysis and rapid heating on volatiles reforming. This study provides a theoretical foundation for understanding efficient hydrogen production from biomass in molten hydroxide salts.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112804
The rapid dissemination of antibiotic resistance genes (ARGs) in aquatic environments poses serious threats to public health and environmental safety under the 'One Health' framework. Nanoplastics (NPs), as co-occurring pollutants, can exacerbate ARG risks by promoting horizontal gene transfer (HGT), yet the influence of different functional groups on extracellular ARG (eARG) transformation remains unclear. This study investigated the effects of carboxy-modified polystyrene NPs (PS-COOH) and amino-functionalized polystyrene NPs (PS-NH2) compared to unmodified polystyrene NPs (PS) on the transformation of the extracellular resistance plasmid IE-V1955 (carrying an ampicillin resistance gene) into Escherichia coli DH5α. Results showed that PS-COOH exposure promoted plasmid transformation similarly to PS, with effects increasing over 0.1–20 mg·L−1. Low concentrations (0.1–0.5 mg·L−1) of PS-NH2 also enhanced transformation, with stronger effects than PS-COOH at equal doses, whereas high concentrations (1–20 mg·L−1) inhibited it. Mechanistically, PS-COOH (0.1–20 mg·L−1) and low PS-NH2 induced intracellular reactive oxygen species (ROS), increased cell membrane permeability, elevated the protein-to-polysaccharide ratio in extracellular polymeric substances (EPS), and promoted biofilm formation, thereby facilitating transformation. High PS-NH2 concentrations caused excessive ROS leading to cell lysis and formed aggregates with plasmids larger than membrane pores, blocking uptake. These findings provide a theoretical basis for assessing the combined environmental health risks of NPs and ARGs.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025121602
This study characterized the body burden of polybrominated diphenyl ethers (PBDEs) in a physical examination population in Shenzhen and evaluated its impact on thyroid function. Serum samples from 368 residents were analyzed for eight PBDE congeners using atmospheric pressure gas chromatography-tandem mass spectrometry (APGC-MS/MS). The median concentration of ∑8PBDEs was 10.2 ng·g⁻¹ lipid weight (lw), ranging from 0.13 to 2089.4 ng·g⁻¹ lw, with BDE-209 predominating (59.7% of total). Multiple linear regression revealed that a 1.7-fold increase in serum BDE-153 was associated with a 0.4% increase in free triiodothyronine (FT3) (P<0.05), while a 1.7-fold increase in BDE-183 was associated with a 0.9% decrease in total triiodothyronine (T3) and a 0.7% decrease in FT3 (P<0.05). Bayesian kernel machine regression (BKMR) indicated a negative correlation between mixed PBDE exposure and thyroid-stimulating hormone (TSH) at high exposure levels. Weighted quantile sum (WQS) regression showed that mixed exposure was associated with decreased T3 levels and T3/FT3 ratio, with BDE-153 and BDE-183 as the primary contributors. These findings suggest that PBDE exposure may adversely affect thyroid function and disrupt thyroid hormone homeostasis, with BDE-183 and BDE-153 playing key roles. This study provides a scientific basis for PBDE health risk assessment and thyroid protection.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025091203
The persistence of tetracycline (TC) in aquatic environments poses significant ecological risks. This study developed a homogeneous reaction system based on carboxylated Fe2+ enhanced peroxymonosulfate (PMS) activation, using citric acid (CA) as a ligand. Carboxylation improved Fe2+ stability and catalytic activity, while solid PMS served as the oxidant, circumventing issues of traditional Fenton processes such as H2O2 instability, complex heterogeneous catalyst preparation, high disposal costs, and toxic metal leaching. The acidic pretreatment enabled by CA inhibited Fe2+ oxidation and promoted sustained PMS activation without external energy input. Under optimized conditions (TC 5 mg·L−1, Fe2+ 0.02 mmol·L−1, CA 0.001 mmol·L−1, PMS 2 mmol·L−1), 88.80% TC degradation was achieved within 60 min. Mechanistic studies revealed that CA protected Fe2+ active sites via carboxyl coordination, facilitating continuous generation of reactive species, including singlet oxygen (1O2) and sulfate radicals (SO4•−). 1O2 was the dominant species (50.5% contribution), followed by SO4•− (35.7%), synergistically driving efficient TC degradation while significantly reducing iron sludge production. Phytotoxicity assays confirmed that treated water exhibited no significant toxicity to wheat seedlings (P > 0.05), indicating effective ecological risk elimination. This work provides a low-energy, operationally simple, and environmentally friendly technology for antibiotic-contaminated water treatment, with promising practical application potential.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010203
The production and disposal of lithium batteries release not only hazardous metals and particulates but also substantial amounts of harmful organic pollutants. This study focuses on N-methyl-2-pyrrolidone (NMP) to investigate the environmental release and human exposure of organic pollutants throughout the lithium battery lifecycle. Using liquid chromatography-high-resolution mass spectrometry (LC-HRMS), NMP was quantified in environmental samples from battery production and dismantling facilities, as well as in pyrolysis products from simulated thermal recovery of mainstream lithium batteries. Key release stages were identified: slurry mixing and coating/drying during production; shredding, electrolyte volatilization, and high-temperature pyrolysis during disposal. In unprotected occupational settings, estimated NMP exposure via dust ingestion exceeded reference doses, underscoring the need for health impact assessments and evaluation of protective measures. This research provides critical insights into the environmental release and population exposure of organic pollutants across the lithium battery lifecycle, informing health policy for vulnerable populations.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024121101
The excessive and uncontrolled use of antibiotics inevitably leads to their release into natural environments, accelerating the production, occurrence, and transport of resistant bacteria and resistance genes. Among these, antibiotic resistance plasmids (ARPs) pose a significant public health challenge due to their environmental persistence and ability to spread and amplify within microbial communities. This study used the tetC gene-pUC18 plasmid as a model ARP to investigate aggregation behavior in aqueous environments under varying pH (3–7), ionic strength (0.001–0.1 mol·L−1 NaCl and 0.001–0.05 mol·L−1 CaCl2), and in the presence of different concentrations of natural colloids. Results indicate that at low pH, ARP structure condenses inward and functional groups may protonate, reducing negative charge and overall size. Compared to Na+, Ca2+ forms cationic bridges between negatively charged phosphate diester groups, significantly enhancing aggregation. Natural colloids induce heteroaggregation with ARPs, with aggregate size increasing with colloid concentration. This study provides scientific evidence for elucidating ARP behavior in soil and groundwater, crucial for assessing risks to human health and ecosystems and understanding global circulation mechanisms.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024122101
Bicarbonate and carbonate ions (HCO3−/CO3^2−) are ubiquitous in wastewater and readily scavenge strong oxidants, leading to the formation of carbonate radicals (CO3·−) in radical-based advanced oxidation processes. This study investigated the influence of HCO3−/CO3^2− on the degradation kinetics of sulfamethazine (SMR) in a UV/TiO2 system. The presence of HCO3−/CO3^2− enhanced the degradation rate of SMR by sixfold compared to UV/TiO2 alone. Radical quenching experiments identified CO3·− as the primary reactive species responsible for the enhanced degradation, with hydroxyl radicals (·OH) also contributing. To quantitatively delineate the roles of reactive species and account for water matrix effects, a kinetic model was constructed using Kintecus software. The model accurately predicted SMR degradation over time and the contributions of individual radicals, demonstrating good predictive capability. Application of the model to real wastewater predicted that CO3·− is the dominant radical responsible for SMR degradation. These findings highlight the critical role of carbonate radicals in UV/TiO2 processes and provide a robust modeling framework for predicting the fate of pharmaceuticals in carbonate-rich waters.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024110202
Anaerobic digestion (AD) is an environmentally friendly biochemical technology for waste treatment and renewable energy production, yet its methane conversion efficiency remains suboptimal. This study employed flux balance analysis (FBA) to determine the optimal temperature for methane production in AD, and subsequently regulated key flexible nodes in the metabolic pathway to maximize methane flux. At the optimal temperature of 40 °C, up-regulating the acetyl-CoA flexible node increased methane flux by 48.5%, while up-regulating the acetate node increased it by 36.6%. The higher improvement via acetyl-CoA regulation is attributed to the fact that 40 °C is unfavorable for hydrogen-producing acetogenic bacteria, making acetyl-CoA the critical control point. These findings demonstrate that flexible node regulation can overcome the limitations of temperature optimization alone. The FBA methodology provides a reliable, cost-effective approach for optimizing target product yields in AD and other fermentation systems, requiring only input and output measurements to resolve intermediate metabolic fluxes.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024120203
Potassium permanganate (KMnO4) oxidation is a promising technology for organic pollutant removal in water due to its low cost and broad pH applicability. However, its moderate oxidation capacity results in slow degradation rates for refractory organic compounds. Carbon materials (CMs), known for their accessibility, stability, and environmental compatibility, have shown great potential in enhancing KMnO4 oxidation. This paper provides a comprehensive review of recent advancements on the enhancement of KMnO4 oxidation of organic pollutants by CMs. The performance and suitability of various CMs in improving KMnO4 oxidation were systematically compared. Additionally, two key mechanisms driving the degradation of organic pollutants in the KMnO4/CMs system were elucidated, along with a discussion on the recycling and regeneration of CMs. Finally, future research directions and development trends for this technology were outlined, aiming to offer insights to advance the practical application of KMnO4/CMs system in water treatment.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024120701
Surface waters contain numerous photoactive substances and low molecular weight carboxylic acids (LCAs). Hydroxyl radicals (HO•) can react with LCAs to generate the highly reducing carbon dioxide anion radical (CO2•−). Excited triplet state dissolved organic matter (3DOM*), a common oxidant in surface waters, may also oxidize LCAs to CO2•−, but this pathway remains unexplored. This study simulated sunlight-driven generation of CO2•− via 3DOM* using 4-benzoylbenzoic acid (CBBP) as a 3DOM* precursor and formate (HCOO−) as a model LCA. Metronidazole (MNZ) served as the target pollutant. Comparative degradation experiments in hν, hν/HCOO−, hν/CBBP, and hν/CBBP/HCOO− systems, combined with electron spin resonance spectroscopy and quenching tests, confirmed that CO2•− generated in the hν/CBBP/HCOO− system was the primary reactive species responsible for enhanced MNZ degradation, originating mainly from 3CBBP* oxidizing HCOO−. Under optimized conditions (8 mmol·L−1 HCOO−, 200 μmol·L−1 CBBP, 10 μmol·L−1 MNZ), 98.2% degradation was achieved within 30 min. Degradation efficiency increased with HCOO− concentration and was pH-independent. Cl−, NO3−, CO3^2−, and low concentrations of HCO3− inhibited degradation, while high HCO3− slightly promoted it. Humic acid (HA) inhibited degradation in a concentration-dependent manner. The system also performed well in real water matrices, suggesting potential for treating micropollutants via reductive pathways.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112102
Based on the 2022 activity data of non-road mobile sources in Hebei Province, this study employed the emission factor method recommended by the Guidelines to estimate emissions of CO, HC, NOx, PM2.5, PM10, and SO2. A comprehensive emission inventory was established, followed by spatial and uncertainty analyses. Scenario analysis, aligned with the 14th Five-Year Plan policies, was used to project emissions for 2030. The results indicate that non-road mobile sources in Hebei emitted 76.1×10^3 t of CO, 20.6×10^3 t of HC, 164.0×10^3 t of NOx, 8.5×10^3 t of PM2.5, 9.0×10^3 t of PM10, and 2.4×10^3 t of SO2. Agricultural machinery was the dominant contributor to CO, HC, PM2.5, and PM10, accounting for over 60.0% of CO emissions. Railway locomotives were the primary source of NOx, contributing 50.9%. For SO2, agricultural machinery and railway locomotives contributed 39.0% and 44.4%, respectively. The highest emitting cities were Tangshan (21.3%), Shijiazhuang (15.7%), Cangzhou (11.6%), and Handan (11.6%). Ship emissions were concentrated in Tangshan Port; civil aviation emissions were mainly in Shijiazhuang, Tangshan, Qinhuangdao, and Handan; railway emissions were distributed in Shijiazhuang, Baoding, and Handan. Under the updated emission standard scenario, NOx and PM10 emissions in 2030 could be reduced by approximately 35.0%. The phase-out of old machinery yielded the largest reduction in CO (36.0%), while both electrification and phase-out scenarios significantly impacted HC emissions.
Environmental Chemistry•2026•DOI: 10.0000/202604-1
An analytical method was developed for the simultaneous determination of 11 organic ultraviolet absorbents (OUVs) in coral tissues using ultra-high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS). Target analytes included benzophenones (BP, BP-2, BP-3, BP-8) and other common UV filters. Sample pretreatment and chromatographic conditions were systematically optimized. Coral tissue samples were extracted by combined vortexing and ultrasonication, separated on a CAPCELL PAK MG C18 column using a mobile phase of methanol-0.1% formic acid aqueous solution under gradient elution, and determined by multiple reaction monitoring (MRM) with internal standard quantification. Method validation demonstrated good linearity for all target compounds over the range of 0.1–500 μg·L−1 (R2 > 0.990), with method detection limits ranging from 0.020 to 0.133 ng·g−1. The mean recoveries at low, medium, and high spiking levels ranged from 60.5% to 120.3%, with relative standard deviations (RSDs) of 1.6%–10.7%. The method offers advantages of simple pretreatment, good repeatability, and high accuracy, making it suitable for high-throughput determination of OUVs in complex biological matrices such as corals. The method was applied to analyze 89 coral samples collected from Xidao Island, Sanya, and five target OUVs were detected in the samples. This method provides reliable technical support for elucidating the accumulation characteristics of OUVs in corals and assessing their potential ecological risks.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604001
This study systematically investigated the occurrence, spatial distribution, sources, and ecological risks of 160 pesticides in Dianchi Lake, a typical plateau lake impacted by agricultural activities. A total of 37 pesticides were detected in the water, with total concentrations ranging from 64.2 to 1132.8 ng/L (average 610.0 ng/L). Fungicides, including boscalid (BOS), fluopicolide (FPC), and dimethomorph (DMM), were dominant, contributing up to 65.0% of the total concentration. Spatially, the southern lake region exhibited significantly higher concentrations (672.5 ng/L) than the north, attributed to intensive facility agriculture. Highly hydrophobic pesticides, such as penconazole (PEN), showed a tendency to enrich in bottom layers. Source apportionment identified inflowing rivers and wastewater treatment plant effluents as primary input sources, with average concentrations 7 and 9 times higher than lake water, respectively. Ecological risk assessment revealed that pesticides posed the highest risk to algae, followed by daphnia and fish. Prometryn (PMT) was identified as a high-risk factor for algae, while profenofos (PFF) and carbendazim (CBD) posed potential threats to higher trophic levels. These findings provide fundamental data and technical support for understanding pesticide pollution in plateau lake ecosystems.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604004
Tire wear particles (TWPs) are emerging pollutants and constitute the dominant type of microplastics (MPs) in urban stormwater runoff, accounting for up to 90% of MPs in some cases. They are characterized by small size, high mobility, complex composition, and significant toxicity. Current research on TWPs remains fragmented, lacking a comprehensive understanding of their environmental behaviors and pollution control in aquatic systems. This review systematically analyzes the enrichment and vectoring roles of TWPs for coexisting pollutants, and their environmental fate, including ecotoxicological impacts, detection methodologies, release of intrinsic additives, and aggregation and sedimentation behaviors. Drawing on insights from other microplastic studies, the paper explores control technologies across the pollution pathway—source, transport, and terminal treatment—and proposes feasible management strategies. Key findings indicate that TWPs can adsorb heavy metals and organic contaminants, with adsorption capacities influenced by aging processes. Their aggregation is governed by solution chemistry, with critical coagulation concentrations varying with ionic strength and pH. The release of additives such as zinc and benzothiazoles is significant, posing ecological risks. Future research should focus on real-water aggregation mechanisms, additive release under natural conditions, long-term performance of treatment facilities like constructed wetlands under TWPs stress, enzymatic degradation pathways, and integration of AI, big data, and IoT for cost-effective detection and risk modeling. This review provides a scientific basis for developing targeted pollution control measures for TWPs in aquatic environments.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604011
Reverse osmosis (RO) membrane fouling remains a critical bottleneck in reclaimed water production, yet its spatial heterogeneity over extended operation is poorly understood. This study investigated fouling characteristics and microbial community dynamics on RO membranes after 3.5 years of operation in a full-scale microfiltration-reverse osmosis (MF-RO) system treating reclaimed water. Long-term monitoring showed stable effluent quality (turbidity <0.1 NTU, conductivity <400 μS/cm), but RO inlet pressure exhibited seasonal fluctuations of 15%–22% between summer and winter, attributed to water viscosity changes. Membrane autopsies revealed distinct fouling layers at the inlet (RO1) and outlet (RO2) ends. RO1 featured a dense bio-inorganic composite fouling layer with CaSO4 crystals and rod-shaped microbial aggregates (5–10 μm), dominated by Proteobacteria (77.11%), particularly Alphaproteobacteria (71.49%) and Xanthobacteraceae (35.29%), which secreted extracellular polymeric substances (EPS) to form biofilms. In contrast, RO2, exposed to higher salinity, showed reduced microbial abundance (Proteobacteria decreased to 64.79%) and a shift toward halotolerant taxa, including Microbacteriaceae (23.73%) and Actinobacteriota (24.76%), with EPS secretion increased by 42%. Alphaproteobacteria relative abundance dropped by 19.3%, while Gammaproteobacteria rose to 12.54%. These findings elucidate salinity-driven microbial succession and spatial heterogeneity of fouling, providing a basis for targeted antifouling strategies and 'zonal-graded' cleaning protocols in reclaimed water plants.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604024
To enhance sludge dewatering efficiency, an MnFe2O4/BC/PMS system was constructed for sludge disintegration. Single-factor and multi-factor experiments were conducted to investigate the effects of MnFe2O4/BC (MFB) dosage, PMS dosage, and reaction time on sludge dewatering performance, establishing the optimal process parameters and the primary-secondary relationships among environmental factors. Active species identification in the MnFe2O4/BC/PMS system revealed the main free radicals responsible for sludge disintegration and the primary pathways of EPS breakdown. Results showed that the influence order of environmental factors on sludge moisture content (Wc) and total organic carbon (TOC) was MFB > PMS > reaction time, while the interaction effects followed MFB-PMS > PMS-reaction time > MFB-reaction time. Optimal dewatering occurred at MFB dosage of 132.99 mg/g DS, PMS dosage of 421.80 mg/g DS, and 18 min reaction time, achieving Wc of 45.8% and TOC of 489.2 mg/L. The ·OH and SO4−· radicals released from MnFe2O4/BC-activated PMS oxidized protein main chains, causing peptide chain breakage. This primarily reduced protein content in sludge from 174.6 mg/L to 75.7 mg/L, with TB-EPS protein content decreasing from 91.8 mg/L to 36.3 mg/L, thereby reducing EPS hydrophilicity and improving sludge dewatering efficiency.