SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4419-1
Proton exchange membrane fuel cells (PEMFCs) fed with reformate hydrogen suffer severe anode poisoning by trace CO, necessitating high CO electrooxidation potentials that degrade performance and durability. This work introduces a Pt@CrSA-N-C anode catalyst featuring a hydrophilic Cr single-atom interface that simultaneously weakens CO adsorption on Pt via electronic regulation and promotes water activation, thereby lowering the CO oxidation onset potential to approximately 0.13 V vs. RHE. The onset potential was determined by two independent methods: the first potential at which the background-corrected current exceeds 0 mA cm-2 during CO oxidation reaction tests in a three-electrode system, and the potential at which the forward scan current exceeds the N2 background current in CO-stripping voltammetry. The catalyst achieves a maximum power density under 100 ppm CO that surpasses reported advanced catalysts, as compiled in Table S5. Structural, spectroscopic, and electrochemical characterizations collectively establish a coherent rationale for the hydrophilic single-atom interface strategy. This approach addresses the longstanding trade-off between CO tolerance and Pt utilization, offering a viable route for low-potential CO removal in practical PEMFC anodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4439-4
Silk fibroin (SF) hydrogels are promising for neural regeneration but suffer from progressive stiffening due to excessive β-sheet assembly, limiting their use in traumatic brain injury (TBI) repair. This study introduces a dopamine (DA)-mediated synergistic topological entanglement strategy to construct an SF-DA/gelatin-DA composite hydrogel (SG). The system integrates covalent cross-linking, net cationic electrostatic repulsion, hydrogen bonding, and π-π stacking to regulate SF assembly dynamics at the molecular level. The resulting SG hydrogel maintains stable mechanical softness over extended periods, with a storage modulus of approximately 1.2 kPa after 28 days, compared to a 5-fold increase in pure SF hydrogels. The sustained softness promotes neural stem cell (NSC) proliferation and differentiation, with a 2.5-fold increase in βIII-tubulin expression and a 1.8-fold increase in GFAP expression after 14 days. In a rat TBI model, SG hydrogel implantation reduced glial scar formation by 40% and improved neurological function scores by 30% at 8 weeks. The hydrogel degrades at a rate of 12% per week, matching tissue regeneration. This multi-crosslinking approach offers a clinically translatable strategy for neural tissue engineering, addressing the critical bottleneck of mechanical instability in SF-based biomaterials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4472-0
Dynamic electrocardiography (ECG) monitoring during physical activity remains compromised by motion artifacts that corrupt signal fidelity, particularly with conventional gel electrodes whose impedance rises sharply under deformation. This work presents a thumb-sized liquid metal system integrating gallium-based epidermal electrodes with a self-adhesive elastomeric matrix to sustain robust ECG acquisition against motion. The electrodes exploit the fluidic compliance of eutectic gallium–indium to maintain continuous skin contact, while the adhesive formulation ensures stable interfacial coupling without additional fixation. The system achieves low motion artifact levels, preserving waveform morphology and R-peak detectability during ambulation. The compact form factor enables unobtrusive wearability, and the materials architecture addresses the trade-off between adhesion and conformability that limits existing dry electrodes. The study establishes a materials and device pathway for clinical-grade dynamic ECG in ambulatory and point-of-care settings, with implications for continuous cardiac monitoring where patient movement is unavoidable.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4479-8
The von Neumann architecture is increasingly constrained by energy consumption and data-transfer efficiency as artificial intelligence and data-intensive applications expand. Neuromorphic computing, inspired by the human brain's information-processing mechanisms, offers an alternative paradigm. Two-dimensional (2D) ferroelectric materials are promising candidates due to their intrinsic non-volatility, atomic-scale thickness, ultra-low power consumption, excellent fatigue endurance, and dangling-bond-free surfaces. This review examines recent advances in 2D ferroelectric materials and associated device architectures for neuromorphic applications. It first introduces ferroelectric mechanisms and representative 2D ferroelectrics, then surveys key device architectures including ferroelectric tunnel junctions, diodes, transistors, and photovoltaic devices. Their applications in in-memory computing and in-sensor neuromorphic systems are discussed, with emphasis on artificial neural networks, spiking neural networks, reservoir computing, and neuromorphic perception for efficient information processing and intelligent sensing. The unique properties of 2D ferroelectrics enable integrated sensing, memory, and computing functionalities, demonstrating potential for future neuromorphic and brain-inspired intelligent systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4371-6
The sluggish kinetics of the oxygen reduction reaction (ORR) necessitates platinum-based catalysts, but their high cost and scarcity drive the search for platinum-group metal-free (PGM-free) alternatives. Fe−N−C catalysts with atomically dispersed Fe−N4 sites are promising, yet their practical performance is limited by buried active sites and poor mass transport. Here, a crumpled, multi-scale porous Fe−N−C catalyst (Fe−N−PCG) is synthesized via spray pyrolysis coupled with high-temperature metal etching. The crumpled morphology, formed by capillary compression during rapid solvent evaporation, and in-plane mesopores from Fe nanoparticle etching, synergistically enhance site accessibility and mass transport. Fe−N−PCG achieves a site density (SD) of 2.74×10^19 sites g−1 and Fe utilization (UFe) of 51.7%. As a gas diffusion electrode, it delivers a mass transport overpotential (ηmt) of 67 mV at 800 mA cm−2. In zinc-air batteries, Fe−N−PCG exhibits a peak power density of 296.1 mW cm−2 at 500 mA cm−2, outperforming Pt/C (241 mW cm−2 at 438 mA cm−2). At 50 mA cm−2, it delivers a discharge voltage of 1.19 V and a specific capacity of 815 mAh g−1, surpassing Pt/C (1.13 V, 715 mAh g−1). These results demonstrate that morphology and porosity engineering can concurrently optimize intrinsic activity, site utilization, and mass transport, offering a rational design strategy for high-performance PGM-free catalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4249-2
Underwater bubble manipulation is critical for water electrolysis, heat transfer, and mineral flotation, yet existing strategies relying on buoyancy or Laplace gradient forces from asymmetric surface geometries suffer from limited flexibility and narrow applicability. This work introduces a temperature-responsive anisotropic cilia surface (TRAS) that achieves bidirectional long-range bubble transport by modulating elastic modulus and stiffness. The TRAS enables precise control over the asymmetric three-phase contact line and viscous resistance, facilitating reversible bubble motion. Experimental validation using aqueous ethanol droplets with varying surface tensions (73.16 mN/m for 0 vol% to 22.27 mN/m for 100 vol%) on cilia with center-to-center spacings of 0.2–1.0 mm reveals that transport direction depends on both cilia spacing and liquid surface tension. Droplets of 0 vol% and 20 vol% ethanol exhibit sustained reverse transport on hard cilia, while 60 vol%, 80 vol%, and 100 vol% solutions show sustained forward transport. Notably, 40 vol% ethanol droplets display bidirectional transport at 0.6 mm spacing, reverse transport at 0.8 and 1.0 mm, and forward transport at 0.2 and 0.4 mm. These results demonstrate that tuning surface tension and cilia spacing provides a versatile platform for directional bubble manipulation, with promising applications in heat transfer, electrochemistry, and gas handling systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4248-2
Marine biofouling imposes substantial operational penalties on maritime assets, yet commercial silicone foul-release coatings rely on static, non-adaptive networks that cannot be reprocessed or repaired. This work introduces selenonium-salt-catalyzed dynamic siloxane exchange as a route to polydimethylsiloxane (PDMS) vitrimer coatings. The authors incorporate A16Se+ organoselenium catalysts into PDMS networks at loadings designated A16Se+xPDMS, enabling thermally activated siloxane bond exchange that confers vitrimeric stress relaxation, reprocessability, and high-temperature self-healing. Antibiofouling performance is benchmarked against pristine PDMS using colony morphology assays for Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa, SEM imaging of bacterial adhesion after 3 h, Chlorella fluorescence adhesion quantification, zeta potential measurements, and 3-month seawater immersion panels. Reviewer 1 questioned the direct relevance of recyclability and high-temperature self-healing to marine antifouling and requested that surface elastic modulus and Pseudomonas antibacterial data be elevated to the main text. In response, the authors relocated scratch and self-healing results from Figure 5 to Supporting Information Figures S12 and S13, condensed the main-text discussion, and integrated surface elastic modulus data into Figure 4G and Pseudomonas antibacterial results into Figure 6A. The revised manuscript positions dynamic exchange as supporting evidence of network dynamics rather than as a primary antifouling metric, while foregrounding modulus and antibacterial performance as the application-relevant properties.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4328-2
Laser-driven broadband near-infrared (NIR) light sources are highly desirable for diverse non-visible optical applications. However, conventional phosphor-in-silicone converters will be rapidly invalidated under high-power laser excitation, and the poor structural stability of Cr3+ activated gallate/germanate phosphors makes them prone to interfacial reaction with silicate glass, leading to substantial deterioration in luminescence properties of phosphor-in-glass film (PiGF) converters. Herein, we report an efficient and stable ultrabroadband NIR PiGF with a high internal quantum efficiency of ≈ 94%, a long peak wavelength of 850 nm and an ultra-large full width at half maximum of 300 nm. The detrimental interfacial reactions with glass matrix are effectively suppressed by embedding the Cr3+ activated superstoichiometric MgO·1.75Al2O3 phosphor, which is attributed to the superior high-temperature structural stability of the aluminate spinels. Through effective thermal management by the sapphire plate and further a motor-driven rotating wheel, a high-performance laser-driven light source is further demonstrated, which can deliver high-brightness ultrabroadband NIR light with an output power exceeding 1.1 W, a light conversion efficiency of 26%, and a stable operation for over 15 hours. Our work provides an efficient, stable and cost-effective all-inorganic converter for the development of laser-driven NIR light sources.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4245-4
The discrimination of volatile organic compounds (VOCs) at trace concentrations remains a critical challenge for environmental monitoring, industrial process control, and non-invasive disease diagnostics. Conventional electronic noses rely on sensor arrays comprising multiple chemically distinct receptors, which introduces fabrication complexity, calibration drift, and cross-sensitivity. Here, we demonstrate that a single-component Ti3C2Tx MXene (TM) sensor array, engineered through controlled surface chemistry and device architecture, generates independent and high-dimensional characteristics (IHC) sufficient for precise VOC pattern recognition. By exploiting the intrinsic heterogeneity of TM basal planes and edge sites, we achieve differential interaction motifs without expanding elemental composition. The array discriminates VOCs including acetone, ethanol, toluene, and hexane at concentrations down to 100 ppb with classification accuracy exceeding 95%. Principal component analysis reveals distinct clustering with cumulative variance of 92.3% captured by the first three principal components. The sensor exhibits a limit of detection of 50 ppb for acetone and response/recovery times of 12 s and 18 s, respectively. Long-term stability tests over 30 days show less than 5% signal degradation. This single-component strategy simplifies fabrication, reduces calibration overhead, and offers a scalable pathway for miniaturized, low-power VOC sensing platforms compatible with Internet of Things (IoT) deployment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4383-8
Conventional cancer therapies remain constrained by undruggable oncogenic proteins and acquired resistance. Proteolysis targeting chimeras (PROTACs) have emerged as a transformative modality that harnesses the ubiquitin-proteasome system to selectively degrade target proteins, offering advantages over traditional small-molecule inhibitors. However, clinical translation of PROTACs is impeded by intrinsic physicochemical limitations: high molecular weight, poor bioavailability, and lack of tumor-specific delivery. Integrating PROTACs with nanotechnology has yielded advanced nano-PROTACs platforms. Nanocarriers enhance solubility and stability, optimize pharmacokinetics, and enable spatiotemporally controlled drug release through passive or active targeting. This review systematically summarizes recent advances in engineering multifunctional nano-PROTACs for cancer therapy, with particular emphasis on design strategies by which nanoengineering enhances PROTAC performance. We evaluate how these platforms improve anticancer efficacy and minimize systemic toxicity while exploring their therapeutic potential in monotherapy and synergistic treatment settings. Finally, we discuss current challenges and future perspectives, providing a theoretical and technical foundation for next-generation nano-PROTACs as a precise and potent strategy in precision oncology.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4412-y
GeTe-based thermoelectric materials are promising lead-free alternatives to PbTe, but their intrinsically high Ge vacancy concentration (~10^21 cm^-3) leads to excessive carrier density and degraded Seebeck coefficient. This study integrates resonant levels (RLs) via In doping and local van der Waals gaps via Sb/Bi alloying to decouple electron and phonon transport. The optimal composition Ge0.91Sb0.04Bi0.04In0.01Te exhibits a Seebeck coefficient of ~287.31 μV K^-1 at 323 K, more than double that of the In-free sample (~102.28 μV K^-1). The peak figure of merit zT reaches ~1.8 at 723 K, with an average zT of ~1.0 over 323–723 K. Vickers hardness is enhanced to ~224 HV, a ~93% improvement over pristine GeTe (~116 HV). X-ray diffraction reveals a structural evolution toward a pseudo-cubic phase with increasing In content, and the (202) peak shifts to lower angles, indicating lattice expansion. These results demonstrate that synergistic RLs and van der Waals gaps effectively optimize carrier concentration and suppress thermal conductivity, offering a viable route for high-performance, mechanically robust GeTe thermoelectrics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4395-x
Electrocatalysts in lithium–sulfur (Li–S) batteries accelerate sulfur species redox reactions and restrict polysulfide shuttling, yet ideal electrocatalysts with remarkable bidirectional catalytic effects remain scarce. This work utilizes iron (Fe) to trigger bidirectional catalytic effects in a cobalt (Co) electrocatalyst, generating a metal alloy-based heterostructure of Co-Co7Fe3 dispersed homogeneously on carbon sheets (Co-Co7Fe3/CS). Electrochemical tests and in situ X-ray diffraction disclose significantly enhanced bilateral catalytic activity of Co-Co7Fe3 compared to bare Co, confirmed by self-discharge measurements. Post-cycling investigation validates protection of the Li metal anode from sulfur species corrosion. The Co-Co7Fe3/CS-modified coin cells deliver an exceptional rate capability of 603 mAh g–1 at 5.0 C and steady long-life cycling for 500 cycles at 1.0 and 2.0 C. Under high sulfur loadings and lean electrolyte conditions, an impressive areal capacity with stable cycling is realized. This work provides valuable insights for designing metal alloy-based heterostructures as advanced electrocatalysts in Li–S batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4480-1
Ternary organic solar cells (OSCs) incorporating a structurally compatible guest acceptor (C7-Cl) into the PM6:BTP-eC9 host system are demonstrated. The low Flory-Huggins interaction parameter between host and guest acceptors facilitates intimate mixing, optimizing molecular packing and energy-level alignment. High-sensitivity sEQE and EQEEL analyses reveal a reduced non-radiative energy loss (KE3) of 0.216 eV in the ternary device. Consequently, the optimized ternary OSC achieves a champion power conversion efficiency (PCE) of 20.02% and an improved T80 operational lifetime of 1065 h. This work establishes a feasible strategy via structurally compatible guest doping to simultaneously optimize vertical phase separation and suppress non-radiative loss, providing a facile and effective route toward high-performance and stable OSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4466-3
Conventional surface coating technologies for 45 steel are constrained by high processing temperatures, limited material compatibility, and insufficient interfacial bonding. This study introduces ultrasonic vibration-assisted mechanical coating (UVAMC) as a low-temperature deposition route that mitigates these limitations. The process yields a chromium coating on 45 steel with a nanoscale elemental interdiffusion transition layer at the interface, achieving a bonding strength of 66.0 MPa. The coating delivers improved corrosion resistance in aggressive environments while preserving the substrate's original compressive and tensile strength. The method also demonstrates broad process adaptability, successfully depositing copper, aluminum, and 316 stainless steel powders, and forming complex shapes such as the "SZU" pattern. These results establish UVAMC as a viable surface functionalization strategy for metallic materials, combining efficient deposition with operational flexibility.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4447-3
Chargeable photoconductivity, a non-volatile photoresponse phenomenon, was investigated in multiferroic heterostructures comprising Bi0.85La0.15FeO3 (BLFO) and a quasi-two-dimensional electron gas (Q2DEG). Two device architectures, LSMO/BLFO/Q2DEG and Pt/BLFO/Q2DEG, were fabricated and characterized under varying electrical connection conditions between the top electrode and the Q2DEG during illumination and dark waiting stages. Current-voltage (I-V) measurements reveal that the heterostructures exhibit persistent photoconductivity after illumination, with the magnitude and retention dependent on the circuit configuration. Under open/open conditions, the photocurrent increases with illumination duration, and subsequent dark waiting leads to a gradual decay, indicating charge storage and release mechanisms. The LSMO/BLFO/Q2DEG heterostructure demonstrates superior chargeable photoconductivity compared to the Pt counterpart, attributed to the oxygen vacancy migration and interfacial polarization effects. These findings establish a foundation for oxide-based photoelectric memory devices with potential for low-power, non-volatile optoelectronic applications. The results provide critical insights into the interplay between ferroelectric polarization, oxygen vacancy dynamics, and charge trapping at the BLFO/Q2DEG interface, offering a pathway for designing advanced multiferroic optoelectronic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4404-7
Electrochemical propylene epoxidation offers a sustainable route to propylene oxide (PO), but achieving high selectivity and stability under industrial current densities remains challenging. Herein, we report a high entropy amorphous CoFeNiCrMnBOx borate loaded with high valence Pt single atoms catalyst (a-Pt-HEBO) for stable bromine radical-mediated propylene epoxidation reaction (BrPOR). The high-entropy amorphous structure reshapes the interfacial hydrogen-bonding network and enriches free water, substantially lowering the energy barrier for water dissociation. Meanwhile, the strong electronic interactions between the coordinatively unsaturated, high-valence single Pt atoms and the substrate effectively prevent transition metal dissolution at high anodic potentials. The catalyst achieved 82.1% Faraday efficiency of PO at an industrial grade current density of 100 mA cm-2, and demonstrated excellent industrial application stability in up to 500 h of continuous test and within a scaled-up electrolyzer (4 × 4 cm2). This work provides a design for high-entropy catalysts in halogen-mediated electrosynthesis and a viable pathway toward carbon-neutral PO production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4309-8
Iridium-doped cobalt oxide nanosheets derived from a ZIF template were evaluated as oxygen evolution reaction (OER) catalysts for proton exchange membrane water electrolysis (PEMWE). Residual carbon was removed via a post-synthetic treatment to isolate intrinsic catalytic behavior. The Ir0.23Co0.77Ox catalyst exhibited enhanced activity and durability relative to commercial IrO2 in a practical PEMWE device. Potential-dependent, stage-resolved characterization combined with theoretical calculations probed catalyst stability under different operating voltages, revealing degradation mechanisms tied to applied potential. Contact angle measurements showed that the Ir0.23Co0.77Ox membrane electrode assembly (MEA) had water and air contact angles of 126° and 143°, respectively, compared to 126° and 143° for an IrO2 MEA at identical Ir loading, indicating improved wettability and gas release behavior. The work provides a framework for understanding potential-dependent stability in acidic OER catalysts and demonstrates a viable route to reduce Ir loading while maintaining PEMWE performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4324-4
Magnesium-oxygen (Mg-O2) batteries offer high theoretical energy density and low-cost earth-abundant magnesium, yet practical deployment has been impeded by poor cycling stability and low energy efficiency, primarily due to the sluggish decomposition of conventional MgOx discharge products. Here we demonstrate that trace water in the electrolyte redirects the cathodic reaction to form chemically reactive Mg2(OH)3Cl·4H2O as the main discharge product, enabling a new reversible pathway: 8Mg2+ + 4Cl- + 3O2 + 22H2O ⇋ 4Mg2(OH)3Cl·4H2O. This water-mediated chemistry significantly enhances redox reversibility compared with the MgOx route. The resulting Mg-O2 battery delivers over 324 stable cycles at 1000 mA·g-1 with a capacity of 500 mAh·g-1 and an energy efficiency of 92%, surpassing all previously reported Mg-O2 systems. The electrolyte comprises 0.25 M magnesium bis(trifluoromethanesulfonyl)imide (Mg(TFSI)2) and 0.5 M magnesium chloride (MgCl2) in ethylene glycol dimethyl ether (DME) with a trace amount of water. These findings establish a general strategy for reversible Mg-O2 electrochemistry and provide a new design paradigm for practical magnesium-based energy storage.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4488-x
Thermochromic smart windows based on hydrogels suffer from inevitable freezing at subzero temperatures and dehydration at elevated temperatures, severely limiting their year-round applicability. This study reports a hydrogel-derived liquid (HDL) smart window that circumvents these limitations through a solvent-exchange strategy. The HDL is synthesized by polymerizing a hydroxypropyl cellulose (HPC) and N-isopropylacrylamide (NIPAM) network in a water-glycerol binary solvent, followed by complete removal of the water phase via vacuum-assisted evaporation. The resulting anhydrous liquid exhibits a lower critical solution temperature (LCST) of 32 °C, with a solar modulation ability (ΔTsol) of 63.2% and a luminous transmittance (Tlum) of 88.1% in the clear state. Critically, the HDL remains optically switchable after 1000 hours at -40 °C and 1000 hours at 80 °C, with no observable phase separation or freezing. The smart window prototype demonstrates a 12.3% reduction in indoor cooling energy consumption in a simulated tropical climate and a 9.8% reduction in heating energy in a cold climate, compared to a commercial low-E glass. The liquid-state formulation enables facile large-area fabrication via roll-to-roll processing, with a demonstrated 30 cm × 30 cm prototype retaining 95% of the initial ΔTsol after 500 bending cycles. This work establishes a viable pathway for all-climate energy-efficient building envelopes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4468-6
The proliferation of multispectral detection platforms demands materials that simultaneously satisfy electromagnetic interference (EMI) shielding and infrared (IR) camouflage without compromising radio-frequency (RF) transmission. Conventional MXene films exhibit exceptional EMI shielding (>40 dB) but suffer from high IR emissivity and severe RF reflection, precluding integration with wave-transmitting arrays. This work introduces liquid metal (LM)-modified MXene composite films engineered via structural patterning to decouple optical, IR, and RF responses. The LM phase, dispersed within the MXene interlayer galleries, reduces free-electron density and tailors the dielectric loss, while a periodic array architecture creates impedance-matched windows for RF transmission. The resulting films achieve an EMI shielding effectiveness of 36 dB at 510 µm thickness, with a low IR emissivity of 0.36 and an RF transmittance exceeding 80% in the X-band. The patterning strategy suppresses surface current continuity, mitigating the trade-off between shielding and transmission. These metrics represent a 20% improvement in IR camouflage and a 15% enhancement in RF transparency relative to pristine MXene films. The composite films also demonstrate mechanical flexibility, retaining 95% of initial conductivity after 1,000 bending cycles. This work establishes a scalable route for multispectral-compatible materials critical for next-generation stealth and communication systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4426-y
Biomedical Mg alloys are candidate biodegradable metals for orthopedic and cardiovascular implants, yet their in vivo service life is governed by coupled mechanical-chemical attack that accelerates loss of mechanical integrity. This review consolidates recent advances in stress-assisted degradation of Mg alloys under physiological conditions, focusing on stress corrosion cracking (SCC), flow-induced corrosion, and corrosion fatigue. Biomechanical-chemical coupling test methods are assessed for their capacity to reproduce physiological loading, fluid shear, and electrolyte chemistry. Mechanistic pathways are analyzed, including anodic dissolution, hydrogen-induced cracking, passivation film rupture, and flow-induced shear stress. Modification strategies for enhancing resistance to stress-assisted degradation are categorized into alloying design, microstructure regulation, and surface treatments. The review further evaluates computer-aided predictive models and multi-physics coupling frameworks that link pit-to-crack transitions, phase-field damage localization, and mechano-chemical peridynamics. Empirical data from the cited literature demonstrate that SCC and corrosion fatigue in chloride-containing media reduce fatigue strength by 40–70% relative to air, while flow-induced shear stresses above approximately 1 Pa disrupt protective films and elevate degradation rates. These findings establish quantitative benchmarks for alloy design and surface engineering. The review concludes that integrating multi-physics modeling with physiologically relevant testing is essential for predicting implant service stability and accelerating clinical translation of high-performance biomedical Mg alloys.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4272-3
Ruthenium (Ru)-based alloys are promising alternatives to commercial Pt/C catalysts for the hydrogen evolution reaction (HER) owing to their low cost and favorable hydrogen adsorption properties. However, the sluggish water dissociation on Ru catalysts remains a major kinetic bottleneck in alkaline solutions. Herein, we report a rare earth (RE) dilute alloy strategy by incorporating a trace amount of cerium (Ce, ~1 at%) into a RuCu alloy to promote interfacial water activation. The oxophilic Ce sites strengthen H2O adsorption and reduce the energy barrier for water dissociation, thereby accelerating the Volmer step during alkaline hydrogen evolution. Consequently, the RuCuCe catalyst delivers 10 mA cm−2 at an overpotential of only 18 mV in 1.0 M KOH and maintains stable operation for over 100 h at 500 mA cm−2 in a membrane electrode assembly. In situ electrochemical impedance spectroscopy and pH-dependent measurements verify the facilitated Volmer process induced by Ce incorporation. Temperature-dependent analysis further shows that the apparent activation energy decreases from 47.4 kJ mol−1 for RuCu to 26.4 kJ mol−1 for RuCuCe, consistent with enhanced water dissociation kinetics. This work establishes RE dilute metal alloys as an effective platform for boosting the intrinsic activity of Ru-based alloy catalysts, in which RE incorporation promotes water dissociation while inducing charge redistribution in the alloy matrix.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4238-2
Infrared nonlinear optical (IR NLO) materials are critical for laser frequency conversion, yet their performance is often constrained by a trade-off between second harmonic generation (SHG) efficiency and laser-induced damage threshold (LIDT). Here, we report a new ternary diamond-like compound, AlGaS3, which successfully balances these competing demands. AlGaS3 crystallizes in a noncentrosymmetric structure composed of wide HOMO-LUMO gap [AlS4] tetrahedra and NLO-active [GaS4] tetrahedra. The compound exhibits a wide experimental optical band gap of approximately 3.38 eV, which is significantly larger than that of the benchmark AgGaS2 (AGS, ~2.70 eV). This wide band gap contributes to a high laser-induced damage threshold (LIDT) of approximately 6.0 times that of AGS, as determined by powder-based measurements. Notably, AlGaS3 also demonstrates a phase-matching SHG response of approximately 0.5 times that of AGS at a fundamental wavelength of 2.09 μm, with particle size-dependent behavior confirming phase-matchability. The combination of wide band gap, high LIDT, and moderate SHG response positions AlGaS3 as a promising candidate for high-power IR NLO applications. This work provides a viable strategy for designing IR NLO materials with enhanced laser damage resistance by incorporating wide-gap tetrahedral units.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4298-x
Conventional electrochemical artificial muscles rely on liquid electrolytes, which suffer from poor encapsulation processability, high leakage risks, and inadequate biocompatibility, limiting their application in bionic medicine, wearable exoskeletons, and humanoid robots. To address these bottlenecks, we fabricated a polyvinyl alcohol-polyacrylic acid (PVA-PAA) double-network hydrogel electrolyte and integrated it with twisted carbon nanotube (CNT) yarns via ultraviolet curing, constructing an all-solid-state artificial muscle unit. The unit maintained structural integrity and actuation performance after mechanical deformation treatments such as weaving and knotting. Experimentally, it achieved a maximum contractile stroke of 16% at −1 to 1.8 V and generated an isometric force of approximately 500 mN at −1 to 2 V. The solid-state artificial muscles exhibited excellent mechanical properties, compact size, and high flexibility, offering new opportunities for applications in bionic medical devices and intelligent robots.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4306-5
Olefin-paraffin separation is a critical and energy-intensive process in the petrochemical industry, with ethylene and propylene purification alone consuming 0.3% of global energy. Current distillation methods are energy-inefficient, and polymer membranes exhibit inadequate separation performance. Metal-organic frameworks (MOFs), particularly ZIF-8, offer precise molecular sieving due to their uniform pore aperture (~3.4 Å), which lies between the kinetic diameters of propylene and propane. Despite excellent lab-scale performance, ZIF-8 membranes face scalability challenges, with effective areas typically below 10 cm², far from the tens of thousands to millions of square meters required industrially. This paper reviews a recent breakthrough by Weihong Xing, Yichang Pan, and colleagues, who developed a micro-space transformation process (MSTP) for scalable fabrication of heterostructured ZIF-8 (HZIF-8) membranes. Using sealed inner lumens of tubular ceramic supports as confined reaction spaces, they achieved single-tube areas of ~200 cm² and total fabricated areas exceeding 4.6 m². The membranes demonstrated stable separation performance over 30 days at 17 bar and 55 °C with a feed flow of 20 Nm³ d⁻¹. This work represents a significant step toward industrial application, addressing critical bottlenecks in membrane area expansion, defect control, and mechanical stability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4269-4
Self-assembled molecular interlayers (SAMs) are promising hole-selective contacts for high-efficiency organic solar cells (OSCs) due to their well-defined energy alignment and minimal parasitic absorption. However, their intrinsically limited mechanical robustness often leads to structural degradation and performance loss under mechanical deformation, restricting their application in flexible devices. Here, we report a nanoparticle-reinforced self-assembled composite interface that simultaneously enhances mechanical reliability and optoelectronic performance. Uniformly dispersed SiO2 nanoparticles are introduced as high-modulus reinforcing building blocks without disturbing molecular self-assembly. In contrast to NiOx nanoparticles, which suffer from aggregation and parasitic absorption, SiO2 nanoparticles exhibit excellent dispersion and optical transparency, enabling formation of a structurally compatible hybrid interface. Mechanistic studies reveal that SiO2 nanoparticles redistribute interfacial stress and form dynamic hydrogen-bond networks with phosphonic acid groups of 2PACz, providing efficient energy dissipation during cyclic deformation. Meanwhile, modulation of interfacial polarity extends the crystallization time window of the active layer, resulting in enhanced molecular ordering and improved charge transport. As a result, devices based on the SiO2/2PACz composite interface achieve a power conversion efficiency of 20.14% for rigid devices and 19.30% for flexible devices, placing the flexible devices among the highest-performing flexible OSCs reported to date, while retaining over 90% of their initial efficiency after repeated bending cycles. This work establishes a general strategy for overcoming the trade-off between electronic selectivity and mechanical robustness in ultrathin self-assembled molecular interfaces, providing design insights for high-performance flexible organic optoelectronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4260-5
Lithium-sulfur batteries (LSBs) are recognized as a leading candidate for next-generation energy storage due to their high theoretical specific capacity (1675 mAh g⁻¹). However, the shuttle effect of lithium polysulfides (LiPSs) severely limits cycle life and energy efficiency. Here, we report a multi-interface engineering strategy employing a MnO₂-TiO₂@Ti₃C₂ MXene (MT@MX) heterojunction, synthesized via a facile redox reaction between MXene and KMnO₄, to modulate bidirectional polysulfide conversion. The 2D structure with high conductivity and abundant heterogeneous interfaces facilitates fast ion/electron transfer, reduces reaction energy barriers, and enhances adsorption via d-band center effects. The stepped built-in electric field (BIEF) in MT@MX lowers the migration energy barrier of LiPSs from catalytic MXene to TiO₂ and then to adsorptive MnO₂, enabling reversible migration across multi-interfaces. Optimized heterointerfaces synergistically integrate adsorption, diffusion, and catalytic conversion, yielding excellent cycling stability even at a high sulfur loading of 6.4 mg cm⁻². This work demonstrates that constructing heterojunctions with stepped BIEF offers a feasible approach to modulate interfacial diffusion and provides a new design strategy for high-performance LSB electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4300-3
The power conversion efficiency (PCE) of organic solar cells (OSCs) has surpassed 21% with the donor polymer D18, yet its processing from non-halogenated solvents like ortho-xylene (o-XY) remains inefficient due to uncontrolled film formation kinetics. Here, we systematically synthesize D18 polymers with molecular weights ranging from 41.6 kDa to 70.9 kDa to modulate crystallization kinetics. In-situ film drying studies reveal that lower molecular weights accelerate solidification, leading to excessive aggregation, while higher molecular weights slow it, causing insufficient phase separation. A medium molecular weight (D18-M) achieves a balanced crystallization rate, promoting favorable morphology and yielding a PCE of 20.55% with L8-BO as acceptor—one of the highest reported for non-halogenated solvent-processed OSCs. Energy loss analysis indicates that although low-molecular-weight polymers exhibit higher intrinsic luminescence, the blend film's emission is governed by exciton environment, which is dictated by morphology. This work underscores the critical role of molecular weight in controlling film formation and morphology, offering a simple yet effective strategy for high-efficiency, environmentally friendly OSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4246-5
Developing organic solar cells (OSCs) processable from green solvents without additives or post-treatments is essential for sustainable manufacturing, yet high power conversion efficiency (PCE) remains difficult due to limited morphology control. Herein, we develop a new electron-deficient building block, dithiazolo[4',5':3,4;5'',4'':5,6]benzo[1,2-d][1,2,3]triazole (DTzBT), which fuses benzo[d][1,2,3]triazole (BTA) with thiazole to leverage S/N-mediated non-covalent interactions, enhance planarity and lower the HOMO. To isolate side-chain effects, two DTzBT-based donors, namely PTzMe-F (N-methyl) and PTzEH-F (N-2-ethylhexyl), have been designed and synthesized. PTzMe-F exhibits poor solubility and miscibility with L8-BO, yielding 2.64% PCE (chloroform). PTzEH-F exhibits excellent processability and favorable morphology, delivering 17.61% PCE (chloroform) and 19.17% as-cast from toluene without any additive or post-treatments. In addition, the ternary LbL device based on PTzEH-F/L8-BO:PC71BM achieved an impressive efficiency of 20.27%. Comprehensive characterization indicates that 2-ethylhexyl side chains afford optimal solubility while preserving strong intermolecular interactions and favorable phase separation. DTzBT mitigates BTA’s HOMO-raising tendency via electron-withdrawing thiazole fusion, reconciling aggregation tunability with energy-level control. These results show that precise backbone and side-chain co-design enables green-solvent, additive-free processing for high-performance OSCs, advancing sustainable photovoltaic manufacturing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4339-7
Neuromorphic computing demands energy-efficient synaptic devices that emulate biological plasticity. Optoelectronic memristors based on colloidal quantum dots (QDs) offer tunable bandgaps and solution processability, yet suffer from defect-mediated nonradiative recombination and instability. Here, we report ZnS-passivated CdZnSe core/shell QDs as the active layer in memristive devices, achieving enhanced synaptic emulation and information encryption. Time-resolved photoluminescence (TRPL) decay curves were fitted with a tri-exponential function, revealing that ZnS passivation suppresses defect-related trap states, prolonging the average carrier lifetime from 12.3 ns (CdZnSe) to 28.7 ns (CdZnSe/ZnS). The intensity proportion of the fast decay component (τ1 ≈ 1.2 ns) decreased from 45% to 18%, indicating reduced surface trapping. Devices incorporating CdZnSe/ZnS QDs exhibit stable bipolar resistive switching with an ON/OFF ratio exceeding 10^3, endurance of >10^3 cycles, and retention of >10^4 s. Under 365 nm UV illumination, the devices show light-tunable synaptic plasticity, including paired-pulse facilitation (PPF) with a facilitation index of 180% at a 50 ms interval, and transition from short-term to long-term memory. The memristors successfully emulate essential synaptic functions and are employed in a simple encryption scheme, demonstrating the potential of defect-passivated QDs for secure neuromorphic hardware.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4340-0
Thin films with nonreciprocal circularly polarized luminescence (CPL) emit circularly polarized light with opposite handedness from its two opposite sides, holding great promise for advancing optical multiplexing technologies. Herein, we introduce component orientation mismatch into chiral composite films via stretching, which leads to macroscopic optical anisotropy and accordingly drives the films to show nonreciprocal CPL activity. Stretching triggers linear dichroism-linear birefringence (LD-LB) coupling to realize nonreciprocal circular dichroism (CD) in elastomer films consisting of thermoplastic polyurethane (TPU) and chiral polyacetylene (R/S-PSA). Moreover, fluorescence anisotropy-linear birefringence (f-LB) coupling occurs after introducing fluorescent groups into the films to achieve multi-color nonreciprocal CPL. The unstretched films exhibit reciprocal CPL with a luminescence dissymmetry factor (|glum|) of 10⁻¹, with handedness determined by PSA’s intrinsic helical chirality. In the stretched films, the oriented fluorescent groups undergo f-LB coupling with matrix crystallization, resulting in nonreciprocal CPL (|glum|=10⁻²). Based on this distinctive chiroptical feature, we have developed chiral logic gates, multidimensional optical encryption systems, and enantioselective photopolymerization platforms to demonstrate the potential uses of the as-obtained CPL films. This work provides both fundamental insights into and a versatile material platform for developing smart nonreciprocal photonic systems with advanced chiroptical functionality.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4250-0
Shape memory polymer (SMP)-based transfer printing offers a promising route for heterogeneous integration of flexible electronics, yet non-contact release reliability remains a critical bottleneck. This study systematically investigates the influence of pickup heating modes—localized versus global—on the release yield and energy-delivery mechanisms through combined experiments and finite element simulations. The localized heating mode concentrates strain energy at the interface, enabling controlled chip ejection with high yield, whereas global heating dissipates energy, leading to release failure. Quantitative analysis reveals that localized heating achieves a release yield of 100% under optimized conditions, compared to near-zero for global heating. The ejection velocity under localized heating is higher, which may induce chip bouncing on the receiver substrate, affecting transfer accuracy; however, this can be mitigated by adjusting release gap and laser parameters. The findings establish a theoretical framework for energy pathway design, providing guidelines for achieving high-yield, accurate non-contact release in laser-induced transfer printing. This work advances the practical application of SMP-based transfer printing for micro-LED displays and flexible electronics, addressing a key manufacturing bottleneck.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4202-3
Carbon dots (CDs) with absorption in the second near-infrared window (NIR-II, 900-1700 nm) hold promise for tumor theranostics, yet existing synthesis methods often involve complex procedures, harsh conditions, or lack precise control. Here we report a 'self-photooxidation-restructuring' strategy that enables structural reorganization of the carbon core in CDs, achieving a significant redshift of absorption into the NIR-II region. Under ultraviolet (UV) light irradiation, the precursor (B-CDs, absorption in UV region) generates singlet oxygen, which self-oxidizes aldehyde groups and the carbon skeleton of B-CDs to stronger electron-withdrawing carboxyl groups and carbon radicals, respectively. These processes facilitate the formation of new C=C bonds between isolated aromatic domains, thereby transforming B-CDs into novel CDs (N-CDs) characterized by enhanced donor-acceptor interactions and a redshift in absorption toward the NIR-II window. Various experimental data, including high-resolution XPS, FTIR, NMR, EPR, have proved the proposed formation mechanism. The novel N-CDs afforded a high photothermal conversion efficiency of up to 71.33%, which enabled 1064 nm laser-activated photoacoustic imaging (PAI)-guided photothermal therapy (PTT) in tumors. This work opens a new avenue for the synthesis and modulation of CDs in the NIR-II region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4342-3
Electron acceptors containing single-bond-linked building blocks offer attractive advantages for organic solar cells owing to their synthetic simplicity and structural modularity. However, achieving backbone planarity without compromising electronic compatibility remains a persistent challenge. Conventional conformational locking strategies based on alkoxy substitution can effectively suppress torsional freedom but often elevate the highest occupied molecular orbital energy level, limiting compatibility with widely used donor polymers. Here, we report a partially fused electron acceptor design that achieves intrinsic backbone planarity through heterocycle selection rather than side-chain-assisted conformational locking. By incorporating a benzodifuran core and furan-thiophene linkages, the resulting acceptors exhibit a near-coplanar backbone geometry as revealed by density functional theory calculations, without the need for electronically perturbing alkoxy groups. Devices based on the optimized acceptor (BDF-1) deliver a binary power conversion efficiency of 12.2%, and further improvement to 19.5% is achieved in a ternary blend with PM6 and BTP-eC9. The enhanced performance is accompanied by favorable morphology, balanced charge transport, and suppressed recombination losses. This work provides molecular-level insight into partially fused acceptor design and demonstrates that heteroatom-guided conformational locking offers a viable strategy for expanding the design space of acceptors with single-bond-linked building blocks while maintaining compatibility with mainstream donor systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4381-5
Bismuth telluride (Bi2Te3)-based alloys remain the benchmark for low-temperature thermoelectric applications, yet their conversion efficiency is limited by the trade-off between electrical and thermal transport. This study introduces a pseudo grain boundary engineering strategy to simultaneously enhance the average figure of merit (ZT) in p-type (Bi,Sb)2Te3 (BST) materials. By incorporating Ag-based compounds, the carrier concentration is optimized via substitution of Ag+ ions, while the introduction of secondary phases at grain boundaries effectively suppresses lattice thermal conductivity. The approach yields a peak ZT of 1.35 at 393 K and an average ZT of 1.25 across 303–483 K, representing a significant improvement over pristine BST. Compared to prior reports, this work achieves superior average ZT while maintaining high electrical conductivity, addressing the longstanding bottleneck of thermal conductivity reduction without compromising carrier mobility. The findings underscore the efficacy of pseudo grain boundary engineering in advancing Bi2Te3-based thermoelectrics for solid-state cooling and power generation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4201-0
Open fracture fixation faces dual critical challenges: bacterial infection and impaired bone healing. This study presents a rationally designed biomacromolecular network coating (Ti-GOED) on titanium alloy bone plates to simultaneously address these issues. The coating integrates antimicrobial and osteogenic components, achieving an optimal balance between antibacterial efficacy and biocompatibility. In vitro assays demonstrated that Ti-GOED eliminates over 99% of common pathogenic bacteria by inhibiting peptidoglycan synthesis, disrupting bacterial cell wall formation, compromising membrane integrity, and leading to intracellular DNA leakage and bacterial death. Concurrently, Ti-GOED enhances the proliferation and osteogenic differentiation of bone marrow mesenchymal stem cells (BMSCs) via activation of the PI3K-Akt and HIF-1 signaling pathways. In vivo animal experiments confirmed strong antibacterial and osteogenic properties. This work provides a strategy for developing antibacterial coatings on medical devices, with significant potential for preventing and treating infections post-fracture fixation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4108-1
Heterogeneous catalysis underpins modern energy conversion, chemical manufacturing, and environmental remediation, yet its advancement is constrained by the scarcity and cost of noble metals. A sustainable alternative lies in activating intrinsically inert sites in earth-abundant materials such as transition metal oxides and carbon-based materials. This review systematically outlines recent advances in activating inert sites within low-cost catalytic materials. We begin by dissecting the physicochemical origins of catalytic inertness, including local atomic symmetry, electronic spin states, and coordination environments. Subsequently, we elucidate mechanisms by which multi-scale strategies—structural engineering, quantum state engineering, and microenvironment engineering—break symmetry, modulate spin states, and construct unique reaction microenvironments, transforming spectator atoms into highly efficient active centers. The review highlights performance breakthroughs in key reactions such as oxygen evolution reaction (OER) and alkane dehydrogenation, where catalytic metrics now rival or surpass noble metal benchmarks. For instance, triangular-ordered Co atoms achieve ampere-level hydrogen production, and tensile strain engineering activates inert non-defect Bi sites for CO2 electroreduction. We critically assess challenges—stability, scalable synthesis, and cost-effectiveness—that hinder industrial translation. Future directions emphasize multi-strategy synergy and artificial intelligence-assisted rational design. This review provides theoretical guidance and technological pathways for subverting noble-metal-dependent paradigms and developing next-generation efficient, low-cost catalytic systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4378-6
Electrical stimulation (ES) is a powerful strategy to mimic endogenous bioelectricity and accelerate complex tissue regeneration, such as chronic wound healing. However, aligning external stimulation with native bioelectrical and biochemical signals for rapid and scarless tissue regeneration remains challenging. Here, we report a wireless bioelectronic dressing (E-dressing) that establishes stable bioelectronic interfaces and precisely modulates cellular physiological activities. Bioactive allylamine-functionalized gold clusterzymes (AM-AuNCs) with intrinsic superoxide dismutase-like activity were designed as functional modifiers to co-polymerize with acrylic acid (AA), forming conductive p(AA-AuNCs) hydrogels. AM-AuNCs impart the hydrogel with superior antioxidant activity, robust interfacial adhesion, and high conductivity, enabling rapid hemostasis, efficient electrical stimulation transmission, and precise fibroblast regulation. Combined with 1.00 V of electrical stimulation, the p(AA-AuNCs) hydrogel significantly promotes fibroblast proliferation, migration, and alignment by upregulating TGF-β, FGF-2, and EGF. Integrated with a biocompatible, flexible zinc-ion battery delivering sustained and tunable electrical signals for over 7 days, the E-dressing precisely guides collagen remodeling, inhibits myofibroblast activation, and maintains Col I/Col III balance, leading to a 5-fold acceleration of wound closure and a 65.5% reduction in scar formation. This multifunctional E-dressing represents a promising bioelectronic device for precise cellular regulation and multimodal regenerative therapy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4369-1
Sodium-ion batteries (SIBs) are promising alternatives to lithium-ion batteries for large-scale energy storage due to sodium's abundance and low cost. Among cathode materials, polyanionic compounds like Na3V2(PO4)2O2F (NVPOF) offer high energy density and dual voltage plateaus at ~3.6 and 4.0 V, but suffer from low electronic conductivity and sluggish Na+ diffusion. Here, we report a dual-modulation strategy combining high-valence Nb5+ doping and polydopamine-derived carbon coating to synthesize Na3V1.94Nb0.06(PO4)2O2F-C (NVPOF-Nb-C) via a hydrothermal route. X-ray diffraction and Rietveld refinement confirm that Nb5+ doping induces slight lattice expansion without altering the tetragonal I4/mmm framework. Density functional theory calculations reveal that Nb5+ doping optimizes the crystal structure and reduces the Na+ diffusion barrier, while the uniform carbon coating enhances electron transport. Consequently, NVPOF-Nb-C exhibits remarkably improved electrochemical performance, including high reversible capacity, excellent rate capability, and ultralong cycling stability. In a full cell with hard carbon anode, it delivers a high energy density of 487.2 Wh kg−1 at 1C and retains 91.51% capacity after 3000 cycles at 20C. This work provides a synergistic strategy to overcome the intrinsic limitations of polyanionic cathodes for practical SIB applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4262-7
The escalating demands of artificial intelligence, machine learning, and neural computing necessitate multifunctional optoelectronic devices capable of integrating sensing, memory, and processing. Two-dimensional van der Waals heterostructures (vdWHs) offer unique advantages, yet their practical deployment is hindered by complex architectures and inefficient mode-switching. Here, we demonstrate a MoTe2/SnS2 anti-ambipolar heterojunction device enabling single-gate reconfiguration among frequency doubling, broadband photodetection, and neuromorphic computing. The device exhibits a peak-to-valley ratio (PVR) of 465, ensuring efficient frequency doubling. As a photodetector, it operates across an exceptionally broad spectral range of 520–2200 nm, with outstanding responsivity and detectivity. Furthermore, the device emulates complete synaptic behaviors, including short-term plasticity (STP), long-term plasticity (LTP), and paired-pulse facilitation (PPF). Integrated into a reservoir computing (RC) system trained on a vehicle motion dataset, it achieves a directional recognition accuracy of 98.7%. This work establishes a paradigm for multifunctional integration and low-power neuromorphic computing, advancing next-generation intelligent optoelectronic systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4315-2
High-temperature X-ray imaging demands scintillators with high crystallinity, efficient scintillation, and robust thermal stability, yet suitable materials remain scarce. Here, we report an ultra-high-crystallinity transparent glass-ceramic (GC) scintillator strategically designed via controllable heat-treatment-induced crystallization. A sequential precipitation method is employed, where cubic CaF2 nanocrystals initially form, subsequently promoting heterogeneous nucleation and growth of hexagonal BaAl2Si2O8. Intrinsic nanoscale phase separation into F-rich and O-rich domains significantly reduces atomic diffusion distances, yielding an unprecedented crystallinity of up to 97.6%. Notably, defect traps (oxygen vacancy defects, likely located within the lattice or at crystalline/amorphous interfaces) enable efficient carrier capture and thermally stimulated release, contributing to remarkable resistance to thermal quenching. Consequently, the GC scintillator maintains 90.6% of its integrated X-ray excited luminescence (XEL) intensity at 300 °C, with the integrated XEL intensity reaching 94.2% of commercial Bi4Ge3O12 (BGO) at room temperature. This enables stable high-temperature X-ray imaging with a spatial resolution of ~10.4 lp mm−1 up to 225 °C. This work provides a versatile pathway for developing high-sensitivity scintillators for extreme-environment X-ray imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4176-y
Three-photon microscopy (3PM) in the near-infrared-III (NIR-III) window (1600–1840 nm) enables high-resolution visualization of cerebral vasculature in vivo, but its imaging depth and quality are limited by the performance of fluorescent probes. Here, we report a probe optimization strategy transitioning from mirror symmetry to centrosymmetry, yielding a highly symmetric aggregation-induced emission (AIE) molecule, T4PQ. The centrosymmetric structure aligns donor-acceptor units, promoting uniform electron cloud delocalization and directional charge transfer, which enhances exciton formation and suppresses non-radiative decay, thereby increasing fluorescence quantum yield. This symmetry also boosts the three-photon absorption cross-section by enhancing electron delocalization and transition dipole moment, enabling stronger nonlinear optical responses under long-wavelength excitation. T4PQ nanoparticles (T4PQ NPs) exhibit an enhanced three-photon absorption cross-section, high fluorescence quantum yield, and excellent photostability. In murine models, T4PQ NPs achieved three-dimensional cerebrovascular imaging at a depth of 1785 μm and real-time hemodynamic observation in microvessels at 1006 μm depth, with good biocompatibility. These results validate the advantage of centrosymmetric molecular design for deep-brain imaging probes, offering a high-performance tool for neurovascular research.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4234-3
The pursuit of high-energy-density sodium-ion batteries (SIBs) necessitates the development of stable high-capacity anodes. While amorphous carbon is a promising anode candidate for SIBs, its practical application is hindered by limited capacity. Herein, we design a composite anode by chemically confining a high-content (~25 wt%) short-chain sulfur into hierarchical porous hard carbon microspheres (SHHC) derived from microbe yeast. The SHHC anode exhibits a high reversible capacity of ~807 mAh g−1 at 0.03 A g−1 (~3 times that of conventional amorphous carbon) along with superior rate capability, and extraordinary long-term cyclability (almost 100% capacity retention after 2000 cycles at 1.0 A g−1). The high-content sulfur species contribute to superb redox reactivity for high-capacity sodium storage via a surface-dominated storage mechanism. The carbon matrix features an enlarged interlayer distance, which facilitates Na-ion intercalation and deintercalation for high-rate capability. Furthermore, the hierarchical porous structure with built-in cavities facilitates the Na-ion transfer and effectively accommodates the electrode’s volume expansion, achieving fast electrode kinetics and outstanding cyclability. Such a combination of favored properties leads to state-of-the-art comprehensive battery performance for Na-ion storage. Our finding envisions a new perspective on building stable high-capacity anode materials for SIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4192-y
Electrochemical water splitting is pivotal for scalable green hydrogen production, yet its practical deployment hinges on cost-effective electrocatalysts with high activity and durability. This study introduces a low-cost, three-dimensional (3D) nanoporous ZrVFeCoNi material fabricated via chemical dealloying, at merely 0.16% of the cost of Pt. The structure-activity relationship between its microstructure and hydrogen evolution reaction (HER) performance was systematically explored. Lattice defect effects from multiphase intermetallic compounds, combined with multi-metal synergy, optimize H+ adsorption energy and electron transfer kinetics. The 3D nanoporous architecture provides a high electrochemical surface area with abundant active sites, enhancing electrolyte penetration and reducing interfacial mass transfer resistance. Consequently, the ZrVFeCoNi electrode exhibits outstanding HER performance, requiring only a 38 mV overpotential to reach 10 mA cm−2 and maintaining stable operation for 1000 h at 500 mA cm−2. Integrated into a full water electrolyzer (ZrVFeCoNi || IrO2/Ni), the system achieves a cell voltage of 1.60 V at a current density of 400 mA cm−2. Advanced characterization and density functional theory (DFT) calculations reveal that interfacial interactions and charge transfer at heterointerfaces drive catalytic activity, showcasing the potential of 3D nano-structured multiphase intermetallic compounds as high-performance electrocatalysts for green hydrogen systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4257-y
Hafnia-based ferroelectrics exhibit a distinctive reverse size effect and exceptional scalability, positioning them as critical candidates for CMOS-compatible non-volatile memory and ferroelectric transistors, with substantial promise for advancing hardware acceleration in artificial intelligence and large-data storage technologies. However, their practical deployment is constrained by a longstanding dilemma: the difficulty in simultaneously stabilizing metastable polar phases and ensuring long-term reliability under the high electric fields required for polarization switching. This review reinterprets this challenge through the lens of defect physics and advocates a paradigm shift from stochastic, disorder-mediated defect incorporation toward ordered, multiscale defect engineering. We systematically discuss the collective influence of point defects, line defects, planar defects, and defect-coupled structures on the phase stability, switching kinetics, and failure mechanisms in hafnia-based ferroelectrics. Controlling oxygen-vacancy states, engineering dopants via Fermi-level and chemical pressure, deploying periodic dislocation arrays, designing topological domain walls, functionalizing interfaces, and leveraging flexoelectric strain gradients constitute the core strategic toolkit. Through such ordered defect architectures, scalable performance metrics, including high remanent polarization, low coercive field, fast switching speed, and endurance exceeding 10^12 cycles, become attainable. These approaches establish a set of design principles for next-generation low-power, high-reliability ferroelectric electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4112-6
Radiostrontium remediation is crucial for ecological protection and sustainable development of nuclear energy. However, efficient removal of 90Sr from complex radioactive liquid waste, especially under acidic conditions, remains challenging due to material instability and intense proton competition. Herein, the rapid and highly selective capture of Sr2+ in neutral and even acidic solutions has been achieved by a layered potassium phosphatoantimonate KSbP2O8 with excellent radiation and thermal stability. Under neutral conditions, it possesses high maximum adsorption capacity (qmSr = 110.25 mg g−1), rapid adsorption kinetics (the removal rate (RSr) of 91.54% within 30 min), and excellent selectivity for Sr2+, and facile regeneration. Particularly, even under acidic conditions (pH 2.0), KSbP2O8 still maintains excellent Sr2+ removal capacity (qmSr = 79.38 mg g−1), fast kinetics, and high selectivity. A mechanism study by multiple characterizations reveals that the efficient Sr2+ removal of KSbP2O8 mainly stems from ion exchange between Sr2+ and interlayer K+ in KSbP2O8, which is attributed to the synergy between the Sb5+-induced Brønsted acidity and the high charge density of the anionic framework. This study demonstrates the exceptional capability of phosphatoantimonates to selectively capture Sr2+ under acidic conditions, highlighting the potential of phosphatoantimonates as effective scavengers for radiostrontium remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4114-5
The precise and controllable synthesis of one-dimensional (1D) and two-dimensional (2D) heterostructures, coupled with the manipulation of their atomic and electronic configurations, is of paramount significance. However, due to the synthetic challenges associated with graphyne (GY) materials, their integration into 1D/2D heterostructures remains considerably difficult. Herein, we demonstrate a post-synthetic intercalation strategy for tellurium onto Ag(111), enabling the controllable fabrication of 1D-GY-nanowire/2D-AgTe-monolayers heterostructures. Scanning-probe microscopies are employed to characterize morphological evolution during the intercalation process. Scanning tunneling spectroscopy results confirm that AgTe monolayer intercalation induces interfacial decoupling of the graphyne nanowires. Density functional theory calculations demonstrate that work function-driven Fermi level modulation via interfacial charge engineering assigns the 1D-GY-nanowire/2D-AgTe-monolayers heterostructures as type-I heterostructures. Our work not only significantly advances the fundamental understanding of interfacial interactions in 1D/2D heterostructures but also presents a scalable strategy for designing heterostructures with tailored electronic functionalities, thereby opening new avenues for applications in advanced nanoelectronics and optoelectronic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4213-x
Lipid peroxyl radicals (ROO·) are terminal propagating species in lipid peroxidation, driving oxidative damage in neurological disorders. Their prolonged lifetime and rapid diffusion within lipid membranes render them difficult to neutralize. Here, we report a bioelectric-responsive TEMPO-doped polydopamine (PDA@TEMPO) nanozyme that sustains catalytic interception of ROO· radicals under persistent oxidative stress. By coupling a PDA redox reservoir with TEMPO catalytic centers, the nanozyme establishes a self-regenerating radical-neutralization cycle via proton-coupled electron transfer (PCET). The π-conjugated framework facilitates charge migration and enables an electric-field-enhanced antioxidant response. In a seizure model, the nanozyme dynamically responds to bioelectric fluctuations, accelerating radical interception and alleviating oxidative stress in neural microenvironments. These findings establish bioelectric-coupled nanozymes as a general strategy for catalytic and sustained regulation of oxidative stress in neural microenvironments, providing a potential therapeutic approach for neurological disorders.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4423-y
Copper-based conductor materials, particularly copper foils, are indispensable for integrated circuit substrates and lithium battery current collectors. The progressive miniaturization of electronic devices demands foils thinner than 10 μm, yet achieving simultaneous ultra-high strength, high ductility, high electrical conductivity, and thermal stability remains a principal bottleneck. Rolled copper foils offer strengths of 200–500 MPa and conductivities of 97–100% IACS, but face production stability limits at reduced thicknesses. Electrolytic copper foils achieve strengths of 600–700 MPa via nanocrystalline refinement but suffer from poor thermal stability and room-temperature self-annealing. Only specialized alloys like Cu-Cr-Zr and Cu-Ag reach the 'double-70' benchmark (strength >700 MPa, conductivity >70% IACS). This highlight reports a transformative advance by Lu's research group, achieving 'double-90' properties (tensile strength >900 MPa, electrical conductivity >90% IACS) in pure copper foils through a gradient super-nano domain (GSD) structure. The GSD architecture, fabricated via electrodeposition under industrial conditions, comprises periodically distributed domains with semi-coherent interfaces and solute atoms (C, O, Cl) that minimize electron scattering. This innovation overcomes the traditional strength-conductivity trade-off, offering a scalable route to high-performance copper foils for advanced chip interconnects, flexible electronics, and ultrathin battery current collectors.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4153-2
Direct seawater electrolysis offers a promising route to green hydrogen production, circumventing freshwater scarcity. However, the presence of chloride ions (Cl−) poses severe challenges, including competing chlorine evolution reaction (CER) and corrosion of anode catalysts. Here, we report a dual-atom catalyst design, RuCr-Ni3P, where Ru atoms with strong chloride affinity and Cr atoms as Lewis acid centers are co-doped into a nickel phosphide matrix. This catalyst exhibits outstanding oxygen evolution reaction (OER) activity and selectivity in alkaline seawater, achieving stable operation for over 4000 hours at industrially relevant current densities. Mechanistic studies reveal that Cl− ions are selectively captured by Ru sites, forming a dynamic Ru–Cl coordination motif that electronically modulates adjacent Ni centers, promoting the formation of high-valent Ni>3+ species. This switches the OER pathway from the lattice oxygen mechanism (LOM) to the more efficient adsorbate evolution mechanism (AEM). Concurrently, Cr sites facilitate the formation of Cr–OH species, creating a localized alkaline microenvironment that further enhances OER kinetics. This dual-site synergistic mechanism transforms Cl− from a detrimental impurity into a beneficial chemical switch, concurrently enhancing both activity and stability. Our findings provide a paradigm shift in seawater electrolysis catalyst design, turning a longstanding challenge into an opportunity for efficient and durable hydrogen production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3828-y
The rapid development of halogen-free solvent-processed organic solar cells (OSCs) has been enabled by side-chain modification on small molecular acceptors, yet the structure-property relationship between inner/outer chain lengths and device performance remains unclear. This study systematically investigates five non-fullerene acceptors (NFAs) with varied side-chain positions and architectures, clarifying the effects of inner versus outer modifications on energy level distribution, film morphology, and carrier dynamics. Notably, longer alkyl chains are not always superior; excessive solubility reduces molecular packing order. The optimized PM6:BTP-TO12 blend achieves a power conversion efficiency (PCE) of 18.2%. Furthermore, ternary OSCs incorporating BTP-TO12 as a guest material reach a remarkable PCE of 19.5%, enhancing the performance of L8-BO-based devices processed with green solvents. This improvement is attributed to the low energy loss and well-controlled aggregation behavior of BTP-TO12 in environmentally friendly toluene. These findings establish a design guideline for side-chain engineering in green-solvent-processed OSCs, achieving state-of-the-art performance and advancing scalable, eco-compatible photovoltaic technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3582-9
Perovskite quantum dots (PQDs) hold great potential for brain-like neuromorphic computing. However, the development of PQDs-based synaptic devices is hindered by interfacial defects and limited stability. Here, we demonstrate a high-performance Cs2AgBiBr6 QDs/organic single crystal heterojunction synaptic device, fabricated via a novel space-confined vertical growth technique combined with a polymer-free transfer process. Vertically grown organic single crystals enable superior carrier mobility and facilitate the formation of low-defect interfaces with PQDs. The heterojunction exhibits remarkable photosensitivity (7.22 × 10^5 at 425 nm) and detectivity (2.15 × 10^15 Jones), owing to the strong optical absorption of PQDs coupled with the superior charge transport characteristics of organic single crystals. Notably, the device achieves dual-functional light adaptation, emulating synaptic behaviour under blue light while exhibiting photo-switching under green/red light. This unique capability enables smart blue-light hazard protection. This work not only provides a versatile platform for high-performance PQDs-based synaptic devices but also advances the development of brain-inspired neuromorphic systems for next-generation computing and intelligent sensing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3629-3
Electrically pumped lasers with reduced physical dimensions are critical for future optical information processing, storage, and photonic integrated circuits. However, electrical injection in perovskite lasers faces challenges including material instability, non-radiative losses, and Joule heating. Here, we demonstrate an ultralow-threshold perovskite microlaser decorated with gold nanoparticles (AuNPs), enabling simultaneous optical pumping and current injection at ambient temperature. The lasing threshold is reduced to 8.6 μJ/cm², approximately 44% lower than that of pristine devices (15.3 μJ/cm²). The AuNPs, with optimized size, enhance both lasing performance and electrical properties, achieving a current injection density of 2.98 kA/cm². AuNPs accelerate hot-carrier cooling, reducing non-radiative recombination and mitigating Joule heating. The threshold decreases progressively with increasing electrical assist fraction. Stability tests confirm excellent resistance to aging and humidity, with stable lasing output under co-excitation in ambient air. This work underscores the feasibility of electrically driven perovskite microlasers, offering a pathway toward electrically pumped microlaser diodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3579-8
Metal sulfides such as CdS are promising for solar-driven H2O2 production but suffer from rapid charge recombination and severe photocorrosion. This study introduces a dual-functional strategy synergizing sulfur vacancy (Sv) engineering and polydopamine (PDA) coating to overcome these limitations. Sv-CdS nanorods were hydrothermally synthesized with tunable vacancy concentrations, followed by in-situ PDA deposition to construct a direct Z-scheme heterojunction. X-ray photoelectron spectroscopy (XPS) and density functional theory (DFT) calculations reveal that the introduction of S vacancies reduces the work function of CdS, facilitating energy level alignment with PDA and enabling efficient electron transfer from CdS to PDA. By tuning the concentration of S vacancies, the charge transfer efficiency can be maximized. As a result, the photocatalytic H2O2 production rate reaches 2539.5 μmol g−1 h−1 under visible light, and further increases to 4395.5 μmol g−1 h−1 after PDA encapsulation—15.6 times higher than that of pristine CdS. Concurrently, PDA enhances O2 adsorption and protects Sv-CdS from photocorrosion. Sv-CdS@PDA exhibited superior photostability compared to Sv-CdS after three consecutive photocatalytic cycles. Mechanistic studies suggest that the Z-scheme heterojunction effectively separates electron-hole pairs: electrons in the conduction band of CdS reduce O2 to ·O2−, which is subsequently converted to H2O2, while holes in the valence band of Sv-CdS oxidize water to replenish O2. This work provides fundamental insights into engineering charge transfer and stability in sulfide-based photocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3564-9
Sluggish water dissociation kinetics in the alkaline hydrogen evolution reaction (HER) hamper its practical production. Here, a heterojunction electrocatalyst featuring Ru-Ni(OH)2 interfaces on nickel foam (NF) with self-engineered built-in electric fields (BIEF) was synthesized via a simple in situ galvanic replacement reaction. The hierarchical Ru-Ni(OH)2/NF exhibits a record overpotential of 9.6 mV at 10 mA cm−2 for alkaline HER, surpassing most reported catalysts and commercial Pt/C. It also shows exceptional activity for hydrazine oxidation reaction (HzOR) at 100 mA cm−2 with a remarkably low potential of ca. 0.015 V vs. RHE. The assembled overall hydrazine splitting (OHzS) system integrating HER and HzOR requires a cell voltage of about 0.09 V to reach 50 mA cm−2, which is 1.637 V lower than the corresponding overall water splitting (OWS) device. Systematic analysis and calculation reveal that the BIEF induces redistribution of interfacial electrons for Ru, facilitating H2O dissociation and intermediate conversion, delivering ultra-high electrocatalytic performance. This work provides an avenue for design and preparation of electric field-mediated catalysts towards sustainable energy conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3558-4
The development of advanced titanium alloys capable of operating above 600 °C remains a critical challenge for aerospace propulsion systems, where conventional Ti alloys suffer from insufficient high-temperature strength and microstructural instability. Here, we propose a computationally driven design strategy for titanium-based medium-entropy alloys (MEAs) that integrates thermodynamic phase prediction with mechanistically informed strength modeling, enabling systematic exploration of the Ti-Nb-Al-Cr quaternary system. The optimized Ti70Nb10Al15Cr5 MEA exhibits exceptional performance metrics: 18% room-temperature ductility (as-cast), a yield strength of 520.7 MPa at 650 °C (post-aging), and an ultralow density of 4.76 g/cm3 (45% lighter than Inconel 718). Microstructural characterization reveals a metastable single-phase BCC structure in the as-cast state, which transforms into a BCC/Ti3Al dual-phase system upon aging, with temperature-dependent precipitate morphology and phase stability. The alloy demonstrates superior high-temperature strength retention up to 900 °C (>80 MPa yield strength), outperforming commercial titanium alloys (e.g., Ti-1100, TG6) and bridging the performance gap between conventional Ti alloys and nickel-based superalloys. This work establishes a multi-criteria design paradigm for entropy-engineered alloys, offering a viable pathway to lightweight, high-temperature structural materials for next-generation aerospace applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3588-2
The rapid evolution of aerospace technology necessitates the development of multi-functional composites that combine light weight, mechanical robustness, thermal protection/insulation, and electromagnetic interference (EMI) shielding. C/SiC porous ceramic composites are promising for thermal protection in hypersonic vehicles. Here, we report a facile strategy to fabricate Cf/SiC composite polymer-derived ceramics (PDCs) via re-pyrolysis of high-energy ball-milled polycarbosilane-vinyltriethoxysilane-graphene oxide (PVG) with Cf/SiC(rGO)p blend interleaves. In-situ generated honeycomb-like cellular structures and non-directional channels reduce density and increase porosity. High-quality SiO2 joints, formed from Si-dangling bonds, strengthen interfacial bonding via a brazing effect, while in-situ SiOC nanowires (SiOCnws) create a hierarchically enhanced network, improving fracture toughness and crack resistance. Multi-scale interfacial/dipole polarization enhances EMI shielding. The optimized Cf(0.2)/SiC(rGO) composite exhibits low density (1.49 g cm−3), high fracture toughness (6.32 MPa m1/2), hardness (7.18 GPa), compressive strength (72.67 MPa), and EMI shielding effectiveness of 58.31 dB. It maintains structural stability under butane blowtorch ablation at ~1300 °C for 3600 s. Porous variants show thermal conductivity of 0.211 W m−1 K−1 with 69.74% porosity. These multi-functional composites are promising for thermal protection systems in aerospace applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3664-x
The proliferation of electronic devices and wireless communications has escalated the demand for materials that simultaneously provide electromagnetic interference (EMI) shielding and infrared (IR) thermal camouflage, a combination critical for military and civilian applications. Traditional metallic shields suffer from high density, poor processability, and cost, while polymer-based alternatives often lack sufficient shielding effectiveness and environmental stability. Here, we report a multilayer composite film fabricated via layer-by-layer vacuum filtration and hot-pressing, integrating modified aramid nanofibers (ANF) and MXene (Ti3C2Tx) nanosheets. The film architecture comprises ANF-polypyrrole (ANF-PPy) as the matrix and Ag-MXene as the functional filler, with in-situ grown Ag nanoparticles intercalating between MXene layers to enhance interlayer spacing and electromagnetic wave scattering. At a thickness of only 33 μm, the film achieves an average EMI shielding effectiveness (SE) of 66.75 dB and a specific shielding effectiveness (SSE/t) of 38432.54 dB cm2 g−1. The multilayer structure promotes multiple internal reflections and interfacial polarization losses, while the tight integration ensures high IR reflectivity. This work establishes a foundation for developing multifunctional protective materials with dual EMI shielding and IR camouflage capabilities, addressing the critical bottleneck of simultaneous performance in ultrathin, flexible formats.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3547-7
Inorganic perovskite solar cells (IPSCs) have attracted significant attention due to their excellent light and thermal stability and potential in tandem applications. However, their efficiency and stability are often limited by residual lattice stress and defects at interfaces and within the bulk, causing severe nonradiative recombination. Here, we introduce a zero-dimensional supramolecular complex, (ETP)2SbCl5, as a dual-interface and bulk modifier to regulate CsPbI3 film growth. The modifier exhibits spatial segregation: ETP+ cations anchor at the buried interface, passivating defects on TiO2 and perovskite surfaces; Sb3+ and Cl− ions diffuse into the bulk during annealing, relieving residual stress; and Cl− accumulates on the top surface, passivating cation defects. Consequently, the modified CsPbI3 solar cell achieves a power conversion efficiency (PCE) of 21.71% and an open-circuit voltage (VOC) of 1.27 V, retaining 97.4% of initial efficiency after 500 h of maximum power point (MPP) tracking. This work demonstrates a synergistic strategy to simultaneously address interfacial and bulk defects, advancing high-performance and stable inorganic photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3559-5
Polyamide (PA) membranes are promising for lithium extraction from spent lithium-ion battery (LIB) leachate but face a trade-off between selectivity and permeability. Here, we demonstrate that nascent PA membranes post-grafted with triaminoguanidinium (TAG) monomers (PA-TAG membranes) gain expanded ion passage channels (0.8–7.1 Å) and enhanced positive charge, achieving high-performance lithium separation. The PA-TAG membrane exhibits a pure water permeance (PWP) of 15.5 L m−2 h−1 bar−1, superior divalent ion rejection (~98%), and an excellent separation factor (~30), significantly outperforming pristine PA membranes. In a simulated acidic battery leachate, the PA-TAG membrane achieved a relative volumetric lithium recovery rate of 48.2% after a two-stage nanofiltration process, with the Li+/M2+ mass ratio of the second permeate reaching 53.35, 445 times that of the feed (0.12). The membrane maintained stable performance over 45 hours of nanofiltration and resisted acidic conditions (pH=2) for at least 20 days. These results highlight the potential of PA-TAG membranes for efficient lithium extraction from acidic battery leachate, addressing the critical need for sustainable recycling of spent LIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3645-3
Postoperative abdominal adhesion, a complication with morbidity exceeding 90%, imposes severe clinical and economic burdens. Existing bioadhesive barriers often exhibit unreliable adhesion to the slippery abdominal wall, risk mispositioning, and neglect frictional stimuli and inflammation. Inspired by the lubricated peritoneum, we developed a programmable adhesive dual-layer Janus patch (DJP) barrier integrating a lubricated layer and an adhesive matrix. DJP achieves rapid, noncovalent interfacial adhesion, subsequently enhanced 2.81-fold via covalent interactions, enabling repositioning within a short time window to improve surgical fault tolerance. The micron-scale poly(sulfobetaine methacrylamide) brush on the DJP surface provides hydration lubrication with a low coefficient of friction (0.06), mimicking peritoneal lubrication and reducing frictional damage to injured tissue. The catechol-containing copolymer confers antioxidative and anti-inflammatory properties, confirmed in vitro. In a rat model, DJP adhering to the injured site significantly reduced collagen deposition between the abdominal wall and cecum, preventing adhesion and promoting tissue healing compared to commercial barriers. This work provides a guiding reference for developing antiadhesive biomaterials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3554-7
Perovskite solar cells (PSCs) have achieved a record power conversion efficiency (PCE) of 27.0%, rivaling silicon-based cells while halving cost, positioning them near commercialization. However, long-term outdoor stability of industrial-scale perovskite solar modules (PSMs) remains a critical challenge. Guo et al. report a milestone: an industrial-scale PSM (aperture area 785 cm2) with a PCE of 19.6% and projected T80 (time to 80% of initial PCE) exceeding 6.7 years under light-dark cycling. The PSM demonstrated stability comparable to commercial silicon solar cells during 45 days of outdoor operation. The key innovation is perovskite surface reconstruction via vapor-deposited terpyridine (Tpy), which reorganizes defective [PbI6]4− octahedra into a zero-dimensional (0D) structure with fully isolated octahedra, eliminating irreversible ion migration. Grazing-incident wide-angle X-ray scattering confirmed formation of (Tpy)2PbI6 on the surface. Time-of-flight secondary-ion mass spectrometry showed that the 0D layer confines iodine migration, making it reversible during light-dark cycles, whereas pristine films exhibit irreversible migration. Temperature-dependent conductivity revealed increased activation energy for ion migration from 0.43 to 0.68 eV. The treated films exhibited photoluminescence lifetime of 532.6 ns and trap density of 1.57×10^15 cm−3. Small-area devices (0.16 cm2) achieved PCE of 25.3%, while scaled modules (785 cm2) retained 19.6%, a new world record. This surface isolation treatment offers a scalable route to stabilize large-area PSMs for outdoor deployment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3575-4
Halide perovskite memristors, known for their ion mobility, have emerged as strong candidates for computational units in next-generation memory and neuromorphic computing systems. Nevertheless, most memristors are limited to operating in a single mode, either resistive switching or threshold switching. In this work, we overcome this limitation by developing dual-mode α-formamidinium lead triiodide (α-FAPbI3) perovskite memristors with switchable volatile/nonvolatile states, enabled by engineered SnO2 electron transport layers (ETLs). Through molecular interface optimization using 3-(N,N′-dimethylmyristylammonio) propanesulfonate (Z14) and 4,4′-(1,10-phenanthroline-3,8-diyl)bis(N,N′-bis(4-methoxyphen-yl)aniline) (PNL), we achieved exceptional device stability. Volatile devices exhibited >500 switching cycles, while nonvolatile devices surpassed 1000 cycles, both maintaining a high on/off ratio (~10^3). Beyond memory applications, these devices successfully emulated biological functionalities. The volatile mode replicated four key nociceptor characteristics (threshold, relaxation, sensitization, and no adaptation), while the nonvolatile mode demonstrated advanced synaptic plasticity, including paired-pulse facilitation (PPF) and spike-timing-dependent plasticity (STDP). Capitalizing on this dual-mode synergy, we constructed a spiking neural network (SNN) for handwritten digit recognition, achieving a 93% accuracy rate—a significant milestone for perovskite-based neuromorphic systems. This study not only provides a material-level strategy for multifunctional memristor design but also bridges the gap between biological sensing and artificial intelligence, paving the way for adaptive neuromorphic hardware.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3628-3
The solution aggregation structures of conjugated polymers are pivotal in determining their film morphology and optoelectronic properties, yet the relationship between solution aggregation and device performance remains elusive in organic photodiode (OPD) systems. Herein, we introduce the first examination of solution aggregation structures of all-polymer OPD blends, with a focus on how molecular entanglement modulates aggregation behavior and subsequent photodiode performance of low-cost poly(3-pentylthiophene). Using small-angle neutron scattering and freeze-dried imaging, we provide a comprehensive analysis of the solution-state aggregation behavior of poly(3-pentylthiophene) and its evolution in the blend, revealing profound impacts on film morphology and device performance. With finely optimized aggregation, the resulting all-polymer OPD achieves a record-high specific detectivity of ~4×10^13 Jones at zero bias, outperforming all bulk heterojunction (BHJ)-type self-powered OPDs reported to date. This device also demonstrates remarkable thermal stability, with negligible performance degradation after over 800 h of thermal annealing at 85 °C. Furthermore, the self-powered OPD exhibits excellent performance across a broad spectral range, enabling its application in both water quality monitoring and biosensing. This work offers new insights into the solution aggregation behavior of conjugated polymers in OPDs and highlights the importance of resolving solution aggregation in optimizing device function.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3623-y
Organic light-emitting diodes (OLEDs) are an advanced technology for full-color displays, yet the low efficiency of blue OLEDs remains a critical bottleneck. Here, we report a new strategy to design robust Pt(II) emitters with enhanced molecular rigidity and increased locally excited character. The resulting Pt(II) emitter exhibits an extremely narrow emission spectrum peaking at 458.6 nm with a full-width at half-maximum (FWHM) of 16.0 nm and a small Huang-Rhys factor of 0.278, together with a high photoluminescence quantum efficiency of 95%. When doped into an OLED, the device emits at 464 nm with high color purity (FWHM = 19 nm) and achieves high external quantum efficiencies (EQEs) of 32.6%, 29.4%, and 26.9% at luminances of 123, 1000, and 5000 cd/m2, respectively. Notably, the device attains a record-high maximum brightness of 84,895 cd/m2 among reported deep-blue OLEDs with Commission Internationale de l'Éclairage (CIE) y-coordinate < 0.15. This work demonstrates one of the highest-performing deep-blue OLEDs reported to date, addressing the dual challenges of efficiency and brightness in this spectral region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3637-6
Traditional optical fiber communication encryption methods lack sufficient dynamic adaptability and hardware flexibility, while reconfigurable logic gates can overcome this limitation, thereby significantly improving the flexibility of encryption systems. This study reports a reconfigurable optoelectronic logic gate (OELG) system based on hafnium-zirconium oxide (HZO) ferroelectric thin films. Through ultra-low temperature atomic layer deposition technique, the fabricated HZO thin films demonstrate an exceptional pyroelectric coefficient of 1835.91 μC m−2 K−1 and robust multi-level polarization stability, enabling efficient broadband photon-to-current conversion. By leveraging the pyroelectric effect and tunable polarization states, the OELG device achieves dynamic optical signal modulation and logic processing. The OELG device supports five fundamental logic operations (AND, OR, NAND, NOR, NOT) via electrical bias and polarization control, without requiring hardware modifications. The OELG device demonstrates stable performance over 10^9 cycles with no degradation, meeting practical application requirements. Furthermore, a convolutional neural network (CNN)-integrated image encryption-decryption framework was validated, achieving 95.01% recognition accuracy on decrypted data, while unauthorized decryption attempts resulted in significant feature loss. This study addresses security challenges in optical communication networks by proposing an innovative solution that integrates pyroelectric materials with reconfigurable logic gate technology, offering a new pathway to enhance physical-layer security.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3744-9
The high-value utilization of industrial wastes is critically important for environmental protection and sustainable development. In this work, amorphous NaFeP2O7 (NFPO) and NaFeP2O7/rGO (NFPO/rGO) composite are synthesized via a selective chemical precipitation approach, utilizing industrial jarosite residue as the iron source. The sodium storage performance and mechanism of this amorphous NFPO/rGO composite as a novel cathode material for sodium-ion batteries (SIBs) are explored for the first time. The as-synthesized amorphous NFPO/rGO composite exhibits outstanding long-term cycling performance of 79.1 mAh g−1 after 1000 cycles at 0.1 A g−1, while the crystalline NFPO/rGO composite does not work. Galvanostatic intermittent titration technique and in-situ electrochemical impedance spectroscopy analysis demonstrate that the amorphous NFPO/rGO composite has high Na+ diffusivity and fast kinetics. In-situ X-ray diffraction analysis reveals the structure change from amorphous NaFeP2O7 to triclinic Na2FeP2O7 during the first discharge process and then evolves to a highly disordered structure in the subsequent charge/discharge cycles. The present work not only provides an avenue for the high-value utilization of jarosite residue but also offers theoretical guidance for the structural design and development of NaFeP2O7-based cathode materials for SIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3746-x
The polyanionic compound Na3V2(PO4)2O2F (NVPOF) possesses a stable three-dimensional framework, high theoretical specific capacity, and favorable operating voltage, yet its sluggish Na+ diffusion kinetics and low electronic conductivity impede industrial application. This study proposes a dual regulation strategy combining carbon coating and heat treatment temperature to synergistically enhance crystallinity and electrochemical performance. NVPOF@C-400 and NVPOF@C-600 were synthesized via in-situ dopamine hydrochloride coating followed by heat treatment at 400 °C and 600 °C, respectively. Carbon coating at 600 °C significantly improved crystallinity and increased electronic conductivity by three orders of magnitude through the carbon layer's conductive network. The ~4.5 nm carbon layer effectively suppressed abnormal grain growth and secondary crystallization aggregation at high temperatures, maintaining uniform particle size of approximately 0.36 μm, which shortens Na+ diffusion pathways and prevents ion transport obstruction. Consequently, NVPOF@C-600 delivered a high discharge capacity of 102.5 mAh g−1 at 20 C and retained 96.5% capacity after 10,000 cycles. In a full-cell configuration with hard carbon (HC), NVPOF@C-600//HC achieved an impressive 89.3% capacity retention after 9,000 cycles. This work provides critical insights for practical implementation of high-performance NVPOF cathodes in sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3506-3
Metallic glasses (MGs) often suffer from sluggish hydrogen evolution reaction (HER) kinetics in neutral and alkaline media, with their catalytic performance predominantly confined to acidic environments. Herein, we reported a novel thermoplastic forming technique to fabricate a self-supported partially crystallized nanoporous Pt56.2Ni5.2Cu16.8P21.8 metallic glass (C-NPMG). The C-NPMG catalyst delivers ultralow overpotentials of 18.0 mV (0.5 M H2SO4), 42.2 mV (1 M KOH), and 88.0 mV (1 M phosphate-buffered saline (PBS)) at a current density of 10 mA cm−2, outperforming most state-of-the-art non-noble MGs and Pt-based benchmarks across all pH conditions. Notably, it maintains negligible performance decay for over 1000 h in alkaline electrolytes, showcasing superior stability. Experimental and computational analyses reveal that the enhanced HER activity arises from three synergistic effects: (1) the high-specific-surface-area nanoporous architecture that maximizes active site exposure; (2) the formation of crystallite-amorphous interfaces during partial crystallization, which lowers the energy barrier for H2 desorption; (3) the hierarchical super-hydrophilic and super-hydrophobic wettability of the C-NPMG, which optimizes mass transport and prevents electrolyte-induced corrosion. This work establishes a novel design paradigm for developing high-performance, pH-universal HER electrocatalysts by integrating structural nano-engineering and crystallite-amorphous phase synergy in metallic glass systems to overcome the trade-offs between performance and stability in electrochemical water splitting.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3682-6
Metal single-atoms with optimized coordination structure on highly accessible substrate can maximize the metal utilization efficiency along with enhancing catalytic activities. Herein, axial nitrogen-coordinated Fe-N5 sites on N-doped carbon (denoted as FeN5@N-C) hollow microplates are fabricated via a unique Fe3+-chelated polydopamine assisted hollowing strategy using ZIF-L microplates as multifunctional templates. Due to the powerful chelating and adhesive ability of polydopamine, this hollow-carbon strategy can be extended to fabricate single-atom Fe-N-C hollow structures with different shapes and encapsulate other transition-metal single atoms (Ni, Co, Mn, and Cu) into the N-doped carbon hollow microplates. The FeN5@N-C hollow microplates exhibit outstanding oxygen reduction reaction (ORR) capability with an impressive half-wave potential of 0.93 V vs. reversible hydrogen electrode and high stability, which can serve as air-cathode catalysts for high-performance Zn-air batteries with high peak power density of 225.3 mW cm−2 and stable cyclability of up to 400 h. Comprehensive analysis and theoretical calculations elucidate that axial nitrogen coordination in Fe-N5 catalytic sites, unlike the planar Fe-N4 configuration, can compete well with the bonding of OH* through additional 3d-2p orbital hybridization, thereby giving moderate bonding strength to enhance the ORR activity.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3625-3
Zirconia (ZrO2)-based fluorite ferroelectric materials are promising for nonvolatile memory and logic devices due to their CMOS compatibility and cost advantages over hafnium oxide (HfO2). However, the metastable nature of the ferroelectric orthorhombic phase (o-phase) hinders practical application. Here, we report the strain-mediated stabilization of the ferroelectric o-phase in ZrO2 thin films grown on niobium-doped strontium titanate (NSTO) substrates with different crystallographic orientations via chemical solution deposition. Systematic structural and ferroelectric characterization, combined with simulation, reveals that substrate orientation controls in-plane tensile strain, selectively promoting epitaxial growth of the o-phase. The ZrO2 film on NSTO(110) exhibits the highest o-phase content, achieving a remanent polarization (2Pr) of 92.64 μC/cm², which remains as high as 88.54 μC/cm² after resistive-capacitive (RC) delay calibration. The device shows endurance of approximately 10^7 cycles with favorable fatigue characteristics. X-ray absorption spectroscopy (XAS) further indicates distortion of Zr-O tetrahedra, providing microscopic insight into the ferroelectricity. This work presents a novel strategy for property tuning of ZrO2 films and supports their application in storage and logic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3649-0
Injectable hydrogels formed via dynamic chemical crosslinks hold great promise as drug delivery platforms due to their robust yet adaptable nature, stimuli-responsiveness, and tunable structures and properties. However, their inherently high water content poses a significant challenge for the efficient encapsulation and sustained release of hydrophobic drugs. Here, we present a novel injectable hydrogel system constructed via a strain-promoted disulfide-thiol exchange between dithiolane-functionalized polymer strands and thiolated core-shell nanoparticles (NPs) under physiological conditions. The hydrophobic core and hydrophilic shell structure of the NPs enables effective loading and protection of hydrophobic drugs, while rapid gelation occurs upon mixing the thiolated NPs with dithiolane-polymers in phosphate-buffered saline. The hydrogel shows excellent injectability, self-healing capability, in vitro biodegradability, and cytocompatibility. This hydrogel system enables sustained release of hydrophobic drugs over 32 days in aqueous media and supports sequential dual-drug release. Its redox-responsiveness under tumor-mimicking reducing conditions, enabled by the disulfide crosslinks, further facilitates controlled intracellular drug release. This multi-component platform offers a versatile strategy for designing advanced injectable hydrogels with potential applications in hydrophobic drug delivery and other biomedical fields.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3705-5
Biodegradable metals (BMs) are designed to corrode gradually in physiological environments, yet this corrosion can compromise their mechanical integrity, potentially causing premature implant failure. For emerging zinc-based alloys, the corrosion-mechanical property relationship remains inadequately characterized. This study systematically investigated the long-term corrosion-associated mechanical behavior of hot-extruded Zn-Cu and Zn-Cu-Fe alloys, promising Zn-based bio-metals, in comparison with pure Zn, under immersion degradation in Hank's solution. Electrochemical impedance spectroscopy and mechanical testing revealed that the evolving corrosion profile governs mechanical performance. Alloying with Cu and Fe mitigated corrosion's detrimental effects: grain refinement reduced localized corrosion susceptibility, while finely dispersed second phases acted as cathodic sites, promoting uniform corrosion. Additionally, Cu and Fe facilitated the formation of protective corrosion product layers, suppressing further matrix attack. Consequently, the overall reduced corrosion, particularly localized corrosion, lowered stress concentration susceptibility, delaying mechanical decline and preserving structural integrity. These findings elucidate the degradation-mechanical property correlation in Zn-based bio-metals and underscore critical considerations for developing new bio-metals for clinical translation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3598-1
Embedding a dielectric layer between as-synthesized graphene nanoribbons (GNRs) and metal surfaces represents a powerful strategy to achieve electronic decoupling, thereby enabling the extraction of these ribbons' intrinsic electrical properties. Although several reports have documented dielectric intercalation between GNRs and metal substrates, studies on Ag(111) substrates are limited. Here, we demonstrate a semiconducting AgTe monolayer intercalation method to achieve electronic decoupling between as-synthesized GNRs and an Ag(111) substrate. Using low-temperature scanning tunneling microscopy, we directly observed the AgTe intercalation process at the GNR/Ag(111) interface. By combining scanning tunneling spectroscopy and density functional theory calculations, we elucidate the critical role of AgTe monolayer intercalation in reducing the interaction between as-synthesized GNRs and the Ag(111) substrate and observe the near-intrinsic electrical properties of the GNRs. Our findings offer a practical and effective strategy for intercalating AgTe monolayers between carbon-based nanomaterials and Ag(111) substrates, facilitating the unambiguous characterization of the near-intrinsic electronic properties of these materials.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(25)61036-5
Large graphene oxide (LGO) sheets offer significant advantages over smaller ones in various applications, yet their production via Hummers-type oxidation of large natural graphite flakes remains challenging due to difficulties in achieving full oxidation and avoiding fragmentation. This study provides the first direct evidence that large graphite flakes (up to 1 mm) can be completely oxidized without fragmentation under static conditions, as revealed by in-situ monitoring. The oxidation process is governed by diffusion of the oxidizer between layers, described by Fick's law, where a high oxidizer concentration gradient increases the diffusion rate. By minimizing the amount of concentrated H2SO4 solvent, we achieved a semi-solid state that elevates oxidizer concentration, facilitating Mn(VII) diffusion and enabling complete oxidation of gram-scale large flakes with significantly reduced reagent consumption. Reaction temperature was optimized to balance graphite oxidation and Mn(VII) self-decomposition. Using this approach, 200-, 100-, and 50-mesh natural graphite were fully oxidized with reduced H2SO4 and KMnO4 usage. After exfoliation, LGO with average lateral sizes of 27.3, 58.7, and 116.2 μm were obtained, respectively, with 100% conversion and yield over 165%. This work not only provides a scalable, cost-effective strategy for LGO production but also advances the fundamental understanding of Hummers-type oxidation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3761-7
Ruthenium-based materials, including metallic Ru and RuO2, are promising electrocatalysts for electrochemical water splitting (EWS) due to their high activity for both hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). However, their practical application is hindered by the relatively strong adsorption of reaction intermediates on Ru surfaces and the oxidative dissolution of RuO2 under operating conditions. This review provides a comprehensive overview of recent progress and challenges in Ru-based electrocatalysts for EWS. We first summarize the fundamentals of EWS, including reaction mechanisms and activity descriptors. Then, we detail typical synthesis methods such as hydrothermal/solvothermal syntheses, organic ligand-assisted syntheses, pyrolysis, acid etching, cation exchange, and molten salt-assisted syntheses. Subsequently, we focus on enhancement strategies, including alloying, doping, structure design, interface engineering, single-atom catalyst design, high-entropy alloy design, phase engineering, and defect engineering, with typical examples illustrating structure-property correlations. Finally, we address remaining challenges and future prospects for the development of efficient and durable Ru-based electrocatalysts for sustainable hydrogen production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3780-3
Real-time health monitoring and ongoing evaluation of physiological conditions are becoming increasingly vital for the advancement of future medical diagnostics and personalized healthcare solutions. Given that certain illnesses necessitate prompt and accessible detection methods, wearable chemical sensors have garnered considerable interest for their capability to monitor health through physiological signals and chemical indicators. This review delivers a thorough examination of recent developments in four primary categories of wearable chemical sensors: biosensors, humidity sensors, gas sensors, and ion sensors. We explore the representative materials, device structures, operating mechanisms, and various application scenarios for each type of sensor. By investigating the latest innovations in these technologies, we aim to provide a detailed overview of the current research landscape, highlight existing challenges, and present potential future directions of wearable chemical sensors in healthcare monitoring.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3708-y
Polar two-dimensional (2D) perovskites, with their excellent semiconductor properties, intrinsic anisotropy, and bulk photovoltaic effect, have emerged as promising candidates for self-driven polarization-sensitive photodetectors. However, these self-driven polarized detectors typically require fabrication along the spontaneous polarization direction to maintain device operation in the self-driven mode, which imposes additional limitations. Herein, we demonstrate multidirectional self-driven polarization-sensitive photodetection by constructing 2D perovskite-based asymmetric contact devices, Ag/2D perovskite/C. The built-in electric field, originating from the difference in work functions, acts as the driving force for the separation and transport of photogenerated carriers. Notably, this approach does not necessitate a specific direction, thereby enabling multidirectional self-driven photodetection. Under excitation by linearly polarized light, our devices exhibit impressive polarization-sensitive discrimination in multiple directions, achieving polarization ratios of 3.3 and 3.1 along the a and b-axes, respectively. Our work enriches the approaches enabling self-driven polarization-sensitive photodetection, free from the previous limitations.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3710-y
Layered transition metal oxide cathodes for sodium-ion batteries (SIBs) suffer from Jahn–Teller distortion of MnO6, Na+/vacancy ordering, and irreversible lattice oxygen loss, causing capacity fading and voltage decay. Here, we report a P2-type material, Na0.67Ni0.3Mn0.6Li0.09Sn0.01O2 (NNMO-Li0.09Sn0.01), co-doped with closed-shell Li+ and Sn4+ ions. Li+ increases the Mn4+/Mn3+ ratio, mitigating Jahn–Teller distortion, and disrupts Ni/Mn ordering, suppressing Na+/vacancy ordering. Sn4+ forms stronger Sn–O bonds (548 kJ mol−1), enhancing bonding between transition metal ions and oxygen, reducing oxygen loss. NNMO-Li0.09Sn0.01 delivers a specific capacity of 90.3 mAh g−1 with 62.9% capacity retention after 50 cycles at 0.1 C (1 C = 200 mA g−1), and 90.3% voltage retention. This closed-shell substitution strategy offers a viable approach for enhancing structural stability of wide-voltage layered oxide cathodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3762-9
The integration of interfacial photothermal conversion and hydrovoltaic effects into bifunctional evaporators offers a promising route to simultaneously address freshwater scarcity and energy demands. However, the development of low-cost bifunctional evaporators and elucidation of the underlying co-generation mechanism remain challenging. Here, we report a porous carbon derived from waste polyester via a metal-organic framework (MOF)-assisted carbonization strategy, which is subsequently fabricated into a bifunctional evaporator for freshwater and hydroelectricity co-generation. The porous carbon exhibits a high specific surface area of 904 m² g⁻¹, hierarchical micro- and mesopores, and abundant oxygen-containing groups. The resulting evaporator demonstrates broadband light absorption, localized thermal management, good hydrophilicity, and high flexibility. Under 1 sun illumination, it achieves an open-circuit voltage of 250 mV, a short-circuit current of 14 μA, and an evaporation rate of 2.34 kg m⁻² h⁻¹, ranking among the most efficient freshwater-hydroelectricity co-generators. The weakened hydrogen-bonding network reduces the water evaporation enthalpy to 1.7 kJ g⁻¹. Mechanistic studies, including molecular dynamics simulations, reveal that selective Na⁺ interaction induces differential ion migration rates, generating a streaming potential. Additionally, the photothermal effect enhances voltage output by promoting interfacial ion concentration gradients. Outdoor tests confirm stable voltage output of 250 mV and freshwater production of 2.34 kg m⁻². This work provides a scalable platform for fabricating advanced evaporators from waste plastics and unravels the co-generation mechanism, offering a sustainable strategy to mitigate freshwater and energy crises.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3748-9
Direct regeneration is a sustainable solution for recycling spent lithium-ion batteries (LIBs), yet the irregular strains induced by the irreversible FePO4 phase after cycling hinder Li+ replenishment in spent LiFePO4 cathodes. This study proposes a lattice stress modulation strategy that reduces FePO4 to Fe2P2O7, reducing unit cell volume from 271.7 to 122.6 Å3, releasing residual stress and reconstructing continuous Li+ transport channels. The phase transformation reconstructs FeO6 octahedra, lowering the migration energy barrier for ions. This synergistically weakens steric effects, facilitating Li+ replenishment and eliminating Li-Fe anti-site defects. Regenerated LiFePO4 cathodes achieve 80.2% capacity retention after 1000 cycles at 2C, outperforming commercial cathodes. The work establishes fundamental principles for the pre-treatment stage of direct regeneration and provides a paradigm-shifting solution for sustainable LIB recycling.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3807-8
Electrocatalytic co-reduction of CO2 and nitrate offers a sustainable route for urea synthesis, valorizing nitrogenous waste and CO2. However, achieving high-performance urea electrosynthesis under ambient conditions remains challenging due to the need for simultaneous activation of CO2 and efficient H2O dissociation to supply active *H for *NOx hydrogenation, ultimately forming key C- and N-containing intermediates for C–N coupling. Here, we report a bifunctional Pd-single-atom-modified Cu (Pd1Cu) nanorod catalyst that synergistically promotes adsorption and stepwise activation of CO2 and H2O, steering the reaction pathway toward selective urea synthesis. Integrating experimental evidence, in situ spectroscopy, and computational analyses, we disclose that atomically dispersed Pd sites kinetically favor co-generation of *CO and *NH2 via H2O dissociation-driven proton transfer, forming an optimal intermediate balance. The dual metal active sites enhance C–N coupling via combined electronic and geometric effects, substantially lowering the reaction energy barrier and improving selectivity. This work provides a rational design strategy for advanced multifunctional catalysts for urea electrosynthesis, contributing to carbon neutrality and waste nitrogen valorization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3805-1
The sluggish kinetics of oxygen reduction and evolution reactions (ORR/OER) at the air electrode impede the practical deployment of fiber zinc-air batteries (FZABs) for wearable electronics. Conventional bifunctional catalysts suffer from an inherent activity trade-off due to the distinct mechanisms of ORR and OER. Here, we propose a spatial decoupling strategy to overcome this limitation by engineering isolated Fe single atoms and Fe–Ir dual-atom pairs on a nitrogen-doped carbon matrix (Fe/FeIr-NC). In this architecture, Fe single atoms serve as ORR centers, while Fe–Ir pairs with tunable spacing are tailored for OER, enabling complete functional separation and independent optimization. The catalyst exhibits an ORR half-wave potential of 0.91 V and an OER overpotential of 250 mV at 10 mA cm−2, yielding a record-low bifunctional gap (ΔE = 0.57 V) that outperforms all reported single- and dual-atom catalysts. A flexible fiber zinc-air battery based on this catalyst delivers a peak power density of 3920 W kg−1, along with a 1.4-fold increase in energy efficiency and a 2.6-fold extension in cycle life compared to the commercial Pt/C + IrO2 benchmark. This work not only breaks the traditional activity trade-off in bifunctional catalysis but also offers a promising route toward high-performance power sources for wearable electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3815-0
The development of bifunctional electrocatalysts capable of integrating biomass-derived platform molecule oxidation with organic reduction offers a promising strategy for simultaneously enhancing energy efficiency and generating high-value chemicals. However, designing catalysts that exhibit both high activity and stability in integrated systems remains a significant challenge. Herein, we report a self-supported electrode composed of nitrogen-doped carbonized wood (NCW) supported NiCo nanosheets (NiCo 0.3/NCW) that enables the electrocatalytic 5-hydroxymethylfurfural oxidation to produce 2,5-furandicarboxylic acid (FDCA) and the nitrobenzene reduction to yield aniline in an integrated electrochemical cell. The NiCo 0.3/NCW electrode achieves the production of FDCA and aniline at a low cell voltage of 1.7 V, with ~99% anodic and ~92% cathodic Faradaic efficiencies, respectively. Experimental characterizations disclose that the hierarchical porous NCW architecture promotes the dispersion of active sites, while nitrogen doping strengthens metal–support interactions. In-situ spectroscopic experiments combined with density functional theory (DFT) calculations reveal that cobalt incorporation tunes the electronic structure of nickel, thus optimizing substrate and intermediate adsorption, and lowering energy barriers. These effects ultimately enhance the performance of the natural wood-derived catalyst in integrated biomass valorization and selective organic electrosynthesis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3681-6
Brominated butyl rubber (BIIR) is widely used in tires and biomedical products due to its excellent elasticity and gas barrier properties, but recycling end-of-life BIIR remains challenging because of its covalent cross-linked network. Here, we report a direct upcycling strategy for unmodified waste BIIR via nanoparticle-mediated interfacial crosslinking, avoiding chemical modification or degradation of the polymer structure. Pyridyl-functionalized silica nanoparticles (SiO2-Py) were synthesized and used to crosslink bromine atoms in waste BIIR with those of fresh BIIR, reconstructing the crosslink network without altering the original sulfur-vulcanization network. The resulting composites exhibit a dual interpenetrating network comprising the sulfur-vulcanized network and a bromine-pyridinium crosslinked silica-rich network, providing exceptional strength and toughness. Using discarded bicycle inner tubes as waste BIIR source, the upcycled composites achieved a tensile strength of ~14 MPa, toughness of ~60 MJ m−3, and ultra-low air permeability of 8.78×10−15 cm3 cm/(cm2 s Pa), significantly outperforming the original inner tube material. This work presents a scalable and effective solution for BIIR waste recycling, advancing sustainable development in the rubber industry.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3713-y
Layered double hydroxides (LDHs) are promising electrocatalysts for the oxygen evolution reaction (OER), yet their practical application remains limited by poor electrical conductivity and sluggish reaction kinetics. In this work, we synthesize three high-entropy LDHs (HELDHs) featuring a hierarchical architecture of microspheres assembled from ultrathin nanosheets, via a simple hydrothermal method using a combination of low-cost, catalytically active transition metals (Fe, Co, Ni, Mn, Zn, Cu, and Cr). Among them, the FeCoNiMnZn HELDH exhibits outstanding OER performance, requiring an overpotential of only 306 mV to reach a current density of 100 mA cm−2. Notably, during 200 h of continuous operation, the device exhibits a stable and, in some cases, increasing current output. This exceptional activity is attributed to the formation of abundant cation vacancies, induced by Zn leaching, which enhance the intrinsic catalytic properties by optimizing the adsorption energies of key OER intermediates. Density functional theory calculations further validate that these vacancies modulate the electronic structure and lower reaction barriers, underscoring the effectiveness of cation-vacancy engineering in high-entropy systems for efficient and durable water oxidation catalysis. The optimized catalyst was further evaluated as the air cathode in a zinc–air battery, demonstrating practical electrochemical performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3725-1
Conductive hydrogel-based stretchable electronics have been extensively investigated, with strain sensors being the most prominently studied. While mechanical properties significantly affect device performance, the systematic correlation between specific mechanical parameters and sensing performance remains rarely explored. This work compares the influences of Young’s modulus and mechanical hysteresis on sensing performance between highly entangled PAM-Li and double-network PAM-Li-Agar-3 strain sensors. Owing to the brittle agar network, which imparts a higher Young’s modulus and pronounced mechanical hysteresis to the double-network PAM-Li-Agar-3 hydrogel, the corresponding sensor requires a greater driving force for deformation and yields signals with poor reproducibility. In contrast, the PAM-Li hydrogel, characterized by highly entangled polymer chains, exhibits a lower Young’s modulus and negligible mechanical hysteresis. Consequently, signals from the PAM-Li strain sensor demonstrate enhanced sensitivity and stability. Therefore, this work demonstrates that a low Young’s modulus and minimal mechanical hysteresis are critical factors for achieving superior sensing performance in strain sensors, as systematically validated through comparative analyses across diverse application scenarios.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3678-1
Reed membrane, a natural cellulosic material traditionally used in musical instruments, holds promise in flexible electronics due to its abundance, low cost, and excellent biocompatibility. However, its native form contains water-soluble ions and lipid-soluble waxes that hinder performance in acoustic and electronics by compromising electrical insulation and mechanical stability. Here, supercritical fluid superposition purification (SCSP-WA) is introduced, which utilizes supercritical CO2 with water and acetone as bipolar co-solvents to selectively remove these impurities. Post-SCSP-WA treatment, the reed membrane exhibits significant enhancements in mechanical strength and electrical insulation, achieving a 4-fold increase in elongation at break, improved tensile strength and Young’s modulus, and a 98.5% reduction in leakage current, all while maintaining low and stable capacitance. These improvements stem from the restructuring of the fibrous network into a porous, interconnected microstructure. Material characterization (X-ray photoelectron spectroscopy (XPS), Fourier-transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM)) confirmed the effective removal of magnesium and waxy functional groups, along with enhanced fiber crosslinking. Cytotoxicity tests further validated the biocompatibility of the SCSP-WA-treated membranes. This environmentally sustainable approach expands the potential of reed membranes in flexible bioelectronics and bio-integrated acoustic systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3760-y
Layered chalcogenide compounds have attracted considerable attention for optoelectronic applications due to their rich structural diversity and unique physical properties, including high carrier mobility, ferromagnetism, ferroelectricity, and outstanding optoelectronic and thermoelectric performance. Their tunable bandgaps and strong light absorption render them highly suitable for next-generation photodetectors. However, the environmental instability of many 2D chalcogenides poses a critical challenge for practical applications. In this work, we report a high-performance, polarization-sensitive photodetector based on an air-stable ternary chalcogenide FeIn2Se4. Angle-resolved polarized Raman spectroscopy reveals that the four characteristic Raman modes exhibit a 60° periodic variation in intensity, highlighting the material's pronounced in-plane anisotropy. Benefiting from its strong absorption over a broad spectral range (510–1028 nm), the FeIn2Se4-based device demonstrates reliable photoresponse under multiple excitation wavelengths (405, 473, 515, and 638 nm), showcasing its wideband detection capabilities. Furthermore, XPS measurements after prolonged air exposure confirm the enhanced chemical stability of FeIn2Se4 compared to binary chalcogenides. These findings demonstrate that 2D ternary FeIn2Se4 is an excellent candidate for advanced anisotropic optoelectronic devices, offering broadband photodetection, robust polarization sensitivity, and excellent environmental resilience.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3665-2
Immuno-phototherapy faces a critical bottleneck: achieving high singlet oxygen (1O2) quantum yield and efficient photothermal conversion simultaneously under a single near-infrared (NIR) laser. Here, we report an acceptor-donor-acceptor (A-D-A) structured molecule, 3,9-bis(2-methylene-((3-(1,1-dicyanomethylene)-6/7-methyl)-indanone))-5,5,11,11-tetrakis(4-hexylphenyl)-dithieno[2,3-d:2',3'-d']-s-indaceno[1,2-b:5,6-b']-dithiophene (m-ITIC), formulated into nanoparticles (NPs) via self-assembly with DSPE-PEG-NH2. The NPs exhibit strong NIR absorption and fluorescence at 688 and 768 nm, respectively. Under single-laser irradiation, they generate heat, superoxide anion (O2•−), and 1O2, with a 1O2 quantum yield of 56.8% and photothermal conversion efficiency (PCE) of 27.4%. This enables NIR fluorescence imaging-guided synergistic photodynamic therapy (PDT) and photothermal therapy (PTT). Notably, the nanoplatform induces PANoptosis—a coordinated cell death program integrating pyroptosis, apoptosis, and necroptosis—in tumor cells, amplifying immunogenic cell death (ICD). This triggers robust dendritic cell activation, macrophage polarization toward M1 phenotype, elevated CD8+ T cell infiltration, and suppression of immunosuppressive Treg cells, leading to significant tumor growth inhibition and prevention of lung metastasis in vivo. Therapeutic efficacy was validated in patient-derived tumor organoids, underscoring translational potential. This study presents a novel single-laser-activated nanoplatform that simultaneously mediates efficient photothermal and photodynamic effects and induces PANoptosis-driven ICD for synergistic cancer immunotherapy.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507064
This study investigates pollutant removal characteristics and kinetic behaviors in sewage networks, and analyzes their impact on the carbon-to-nitrogen ratio (C/N, as COD/TN) of influent to wastewater treatment plants. Source water quality sampling at drainage outlets revealed spatial and temporal variations in C/N, with domestic sewage exhibiting higher C/N than industrial sewage, and diurnal peaks reaching 6.92 versus 4.71 during off-peak hours. Using a pilot-scale adjustable sewage network system in Kunshan, experiments were conducted under high (0.491 m·s−1) and low (0.089 m·s−1) flow velocities, monitoring pollutant removal over 144 hours. Pseudo-first-order kinetics were applied to model COD and TN removal. Results showed that COD (including SCOD and PCOD), BOD5, and SS achieved approximately 80% removal within 144 h, with higher removal at low flow velocity. TN, NH3-N, and TP exhibited lower overall removal rates. Kinetic fitting revealed that COD removal rate constants (kCOD) were significantly higher than those for TN (kTN), and both decreased with increasing flow velocity: at low velocity, kCOD=0.0167 h−1 and kTN=0.0029 h−1; at high velocity, kCOD=0.0127 h−1 and kTN=0.0020 h−1. Simulations based on actual source pollutant concentrations indicated that the time for C/N to drop to the denitrification critical value of 4.50 was 12.24 h at high velocity, but shortened to 9.49 h at low velocity. These findings demonstrate that increasing flow velocity effectively retards the decline of C/N. Therefore, regulating network flow velocity to reduce hydraulic retention time is a key strategy for maintaining adequate C/N at the terminal and ensuring denitrification efficiency in wastewater treatment plants.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507085
This study investigates the spatiotemporal differentiation of suspended particulate matter (SPM) characteristics, sources, and their impacts on water quality between the Middle Route (closed artificial channel) and East Route (open natural water system) of the South-to-North Water Diversion Project. Thirty sampling sites (13 on the Middle Route, 17 on the East Route) were established, and samples were collected during dry and wet seasons. Water quality parameters and SPM characteristics were analyzed, including particle size distribution, total suspended solids (TSS), chlorophyll a, and stable carbon and nitrogen isotopes. Results show that the Middle Route maintains good and stable water quality, with SPM dominated by coarse particles (>63 μm, 61.43%–94.68%), total phosphorus (TP) <0.01 mg·L−1, and a significant positive correlation between chlorophyll a and coarse particles (r=0.60), indicating algal aggregation dominates particle formation. In contrast, the East Route exhibits high and fluctuating nitrogen and phosphorus concentrations, with SPM dominated by fine particles (<20 μm, 51.26%–88.61%), TP ranging from 0.03 to 1.11 mg·L−1, and a positive correlation with fine particles, suggesting significant external inputs. Carbon and nitrogen isotope analysis reveals that Middle Route SPM primarily originates from autochthonous algae (contribution >46.75%), while East Route SPM is influenced by both terrestrial C3 plants and algae. The distinct engineering and management approaches of the two routes lead to significant differences in SPM characteristics and sources, thereby affecting water quality dynamics. The Middle Route requires an 'algal reduction and hydrodynamic optimization' strategy to control algal-derived coarse particle deposition, whereas the East Route benefits from 'retention-sedimentation and wetland purification' to reduce external fine particles and pollutant inputs. This research provides theoretical support and practical guidance for differentiated SPM management in long-distance water diversion systems.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507110
Algal-derived taste and odor compounds (2-methylisoborneol, 2-MIB, and geosmin, GSM) in drinking water sources are poorly removed by conventional treatment. This study systematically evaluated the standalone and combined performance of ozone micro-nano bubbles (O3-MNBs) oxidation and powdered activated carbon (PAC) adsorption for removing 2-MIB, GSM, and algal cells from source water. Results showed that O3-MNBs pre-oxidation achieved >97.5% removal of odorants at 400 ng·L−1 and 67.2% algal cell removal within 30 min. When applied as a deep treatment stage, the degradation rate constant (k) was 10.1%–25.6% higher than in pre-oxidation due to lower background matrix interference. Both pre-oxidation and deep treatment reduced effluent concentrations of 2-MIB and GSM to below 10 ng·L−1, with oxidation kinetics fitting pseudo-first-order models (R²>0.95). PAC adsorption of both compounds followed pseudo-second-order kinetics (R²>0.99), with GSM equilibrium adsorption capacity approximately 20.0% higher than that of 2-MIB. In pure water, adsorption capacity increased by >10.0% compared to raw water. Based on kinetic models, a quantitative prediction method was established for O3-MNBs oxidation and PAC adsorption processes, aiming to achieve efficient odorant removal and cost optimization, providing theoretical support for advanced drinking water purification and smart water plant construction.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506021
To elucidate the seasonal variation in cadmium (Cd) accumulation in ratoon rice and its relationship with root surface iron plaque, this study compared Cd concentrations in brown rice and the characteristics of iron plaque components (amorphous Fe, Am-Fe; crystalline Fe, Cry-Fe) between the main and ratoon crops of six rice varieties under different stubble heights. A field experiment was conducted in a Cd-contaminated paddy in Liuyang, Hunan (soil total Cd: 0.56 ± 0.06 mg·kg⁻¹). Ratoon crop treatments included low stubble (20 cm) and high stubble (60 cm). Brown rice Cd concentrations varied by variety, season, and stubble height. Low stubble generally increased brown rice Cd in the ratoon crop compared to high stubble; high stubble reduced Cd in most varieties relative to the main crop. Health risk assessment indicated that low stubble in the ratoon crop posed higher non-carcinogenic risk than the main crop and high stubble, while carcinogenic risks exceeded acceptable levels across all treatments. Iron plaque Am-Fe and Cry-Fe concentrations in the ratoon crop were generally lower than in the main crop, with Am-Fe consistently exceeding Cry-Fe. In the main crop, total Fe, Am-Fe, and Cry-Fe on root surfaces were significantly negatively correlated with brown rice Cd (P < 0.05), but correlations were not significant in the ratoon crop. High stubble reduced Cd accumulation and non-carcinogenic risk in most varieties, yet carcinogenic risk remained. Iron plaque significantly impeded Cd uptake in the main crop but its effect weakened in the ratoon crop. Selecting low-Cd-accumulating varieties and optimizing stubble height are key strategies for safe ratoon rice production in Cd-contaminated areas.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507032
To mitigate global warming, regional carbon neutrality pathways are critical. Based on the Guangdong Energy Policy Simulator (EPS) model, this study simulates total energy consumption and greenhouse gas (GHG) emissions under baseline, Carbon Neutral 60 (CN60), and Carbon Neutral 50 (CN50) scenarios, and analyzes the emission reduction effects and costs of various energy policies. Results show that by 2060, total energy consumption under CN60 and CN50 decreases by 39% and 44% relative to baseline, respectively. Primary electricity and other energy, natural gas, oil, and coal account for 56%, 26%, 14%, and 4% under CN60, and 60%, 24%, 13%, and 3% under CN50. GHG emissions under CN60 drop to 80×10^6 tCO2e by 2060, an 89% reduction from 2020; under CN50, emissions reach 92 and 55×10^6 tCO2e in 2050 and 2060, respectively, reductions of 87% and 92% from 2020. Policies such as increasing clean electricity share, industrial electrification (hydrogen), increasing green power purchases, building electrification, F-gas reduction, and improving industrial energy efficiency standards show significant reduction effects, with clean electricity share being the primary source. Policies like improving industrial energy efficiency standards, increasing industrial product utilization, and increasing clean energy vehicle market penetration are cost-effective; increasing clean electricity share, green power purchases, building electrification, and F-gas reduction effectively balance reduction effects and costs. Industrial electrification (hydrogen) contributes >5% cumulative reduction but faces economic challenges for full-scale promotion in the short term; industrial carbon capture and storage and electrolytic hydrogen contribute <2% cumulative reduction with high costs. Therefore, Guangdong should prioritize cost-effective policies, promote balanced policies, gradually optimize energy structure, achieve clean electricity, and foster green industrial transformation to achieve carbon neutrality at lower economic cost.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60617-7
The global energy landscape is undergoing a profound transformation, with wind energy gaining increasing prominence due to its clean and renewable nature. However, as installed wind power capacity expands, disposal of waste wind turbine blades (WWTB) has emerged as a significant challenge. These blades are predominantly composed of epoxy resin (EP) polymers, carbon fibers (CFs), and glass fibers (GFs). Improper disposal exacerbates environmental concerns and leads to loss of valuable resources, particularly carbon-based materials. Pyrolysis technology, a versatile and environmentally sustainable method for resource recovery, has garnered considerable attention for WWTB disposal. This work presents a comprehensive review of pyrolytic recycling of WWTB, focusing on principles and classifications of pyrolysis technology, key factors influencing the pyrolysis process, as well as pyrolysis methods, equipment, products, and their applications. Through in-depth analysis of current research, this review identifies critical unresolved issues and provides a forward-looking perspective on emerging research trends. The review highlights that pyrolysis can effectively recover glass fibers and carbon fibers with mechanical property retention depending on process conditions, and that catalytic pyrolysis can enhance the quality of recovered products. Economic analysis indicates that collaborative disposal methods can improve cost-effectiveness. Future research should focus on optimizing process parameters for large-scale industrial application and developing more efficient catalysts to improve product selectivity and fiber quality.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025121602
This study characterized the body burden of polybrominated diphenyl ethers (PBDEs) in a physical examination population in Shenzhen and evaluated its impact on thyroid function. Serum samples from 368 residents were analyzed for eight PBDE congeners using atmospheric pressure gas chromatography-tandem mass spectrometry (APGC-MS/MS). The median concentration of ∑8PBDEs was 10.2 ng·g⁻¹ lipid weight (lw), ranging from 0.13 to 2089.4 ng·g⁻¹ lw, with BDE-209 predominating (59.7% of total). Multiple linear regression revealed that a 1.7-fold increase in serum BDE-153 was associated with a 0.4% increase in free triiodothyronine (FT3) (P<0.05), while a 1.7-fold increase in BDE-183 was associated with a 0.9% decrease in total triiodothyronine (T3) and a 0.7% decrease in FT3 (P<0.05). Bayesian kernel machine regression (BKMR) indicated a negative correlation between mixed PBDE exposure and thyroid-stimulating hormone (TSH) at high exposure levels. Weighted quantile sum (WQS) regression showed that mixed exposure was associated with decreased T3 levels and T3/FT3 ratio, with BDE-153 and BDE-183 as the primary contributors. These findings suggest that PBDE exposure may adversely affect thyroid function and disrupt thyroid hormone homeostasis, with BDE-183 and BDE-153 playing key roles. This study provides a scientific basis for PBDE health risk assessment and thyroid protection.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010302
Cadmium (Cd) contamination of agricultural soils poses significant economic and health risks. While extensive research has focused on Cd accumulation in staple crops like rice, data on oilseed crops remain scarce, hindering safety assessments of edible oils and oilseed meals. This study investigated Cd accumulation and translocation in rapeseed (Brassica napus) grown in You County, Hunan Province, a region severely contaminated with Cd. Rhizosphere soil and plant tissues (roots, stems, seeds) were collected and analyzed for Cd concentrations. Results showed that approximately 71% of rhizosphere soil samples exceeded the agricultural soil pollution risk screening value for Cd, indicating high ecological risk. Cd concentrations in roots and stems were (0.49 ± 0.39) mg·kg⁻¹ and (0.54 ± 0.31) mg·kg⁻¹, respectively, comparable to or higher than soil Cd levels (0.51 ± 0.31) mg·kg⁻¹, with elevated bioaccumulation and translocation factors. This suggests that improper disposal of rapeseed roots and stems, such as returning them to fields or burning, could lead to secondary Cd pollution. In contrast, Cd bioaccumulation and translocation factors in seeds were less than 1, and Cd concentrations in seeds, oil, and oilseed meals were relatively low. Comparative analysis with sesame, camellia oleifera, and peanut indicated that rapeseed-derived oil and meal contain lower Cd levels, positioning rapeseed as a promising low-Cd-accumulating edible oil crop for cultivation in Cd-contaminated areas.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024083002
Selenium (Se) is an essential trace element for human health, and dietary intake through Se-rich crops is the primary route. However, total soil Se content does not directly reflect the bioavailability to plants, which depends largely on soil available Se. This study, conducted in Shipai Town, Longshan County, Hunan Province, used 1:50,000 land quality geochemical survey data to investigate factors influencing the Se bioaccumulation coefficient in maize kernels. Soil pH, CaO, and MgO were identified as significantly positively correlated with the bioaccumulation coefficient and were selected as proxies for soil available Se. A random forest (RF) model was developed to predict maize grain Se content and assess the feasibility of cultivating Se-rich maize in low-Se farmland. Results showed that although soil Se was deficient, 53.64% of maize grain samples met the Se-rich product standard (0.02–0.30 mg·kg−1). Compared with multiple linear regression, the RF model exhibited higher accuracy and reliability. The RF model predicted that 40.91% of farmland in the study area is suitable for natural Se-rich maize cultivation, representing a 25.86% increase over the area identified by soil total Se alone. This study provides a novel methodological framework for planting natural Se-rich maize in Se-deficient regions, validating the potential for such cultivation.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024110202
Anaerobic digestion (AD) is an environmentally friendly biochemical technology for waste treatment and renewable energy production, yet its methane conversion efficiency remains suboptimal. This study employed flux balance analysis (FBA) to determine the optimal temperature for methane production in AD, and subsequently regulated key flexible nodes in the metabolic pathway to maximize methane flux. At the optimal temperature of 40 °C, up-regulating the acetyl-CoA flexible node increased methane flux by 48.5%, while up-regulating the acetate node increased it by 36.6%. The higher improvement via acetyl-CoA regulation is attributed to the fact that 40 °C is unfavorable for hydrogen-producing acetogenic bacteria, making acetyl-CoA the critical control point. These findings demonstrate that flexible node regulation can overcome the limitations of temperature optimization alone. The FBA methodology provides a reliable, cost-effective approach for optimizing target product yields in AD and other fermentation systems, requiring only input and output measurements to resolve intermediate metabolic fluxes.