SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4439-4
Silk fibroin (SF) hydrogels are promising for neural regeneration but suffer from progressive stiffening due to excessive β-sheet assembly, limiting their use in traumatic brain injury (TBI) repair. This study introduces a dopamine (DA)-mediated synergistic topological entanglement strategy to construct an SF-DA/gelatin-DA composite hydrogel (SG). The system integrates covalent cross-linking, net cationic electrostatic repulsion, hydrogen bonding, and π-π stacking to regulate SF assembly dynamics at the molecular level. The resulting SG hydrogel maintains stable mechanical softness over extended periods, with a storage modulus of approximately 1.2 kPa after 28 days, compared to a 5-fold increase in pure SF hydrogels. The sustained softness promotes neural stem cell (NSC) proliferation and differentiation, with a 2.5-fold increase in βIII-tubulin expression and a 1.8-fold increase in GFAP expression after 14 days. In a rat TBI model, SG hydrogel implantation reduced glial scar formation by 40% and improved neurological function scores by 30% at 8 weeks. The hydrogel degrades at a rate of 12% per week, matching tissue regeneration. This multi-crosslinking approach offers a clinically translatable strategy for neural tissue engineering, addressing the critical bottleneck of mechanical instability in SF-based biomaterials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4472-0
Dynamic electrocardiography (ECG) monitoring during physical activity remains compromised by motion artifacts that corrupt signal fidelity, particularly with conventional gel electrodes whose impedance rises sharply under deformation. This work presents a thumb-sized liquid metal system integrating gallium-based epidermal electrodes with a self-adhesive elastomeric matrix to sustain robust ECG acquisition against motion. The electrodes exploit the fluidic compliance of eutectic gallium–indium to maintain continuous skin contact, while the adhesive formulation ensures stable interfacial coupling without additional fixation. The system achieves low motion artifact levels, preserving waveform morphology and R-peak detectability during ambulation. The compact form factor enables unobtrusive wearability, and the materials architecture addresses the trade-off between adhesion and conformability that limits existing dry electrodes. The study establishes a materials and device pathway for clinical-grade dynamic ECG in ambulatory and point-of-care settings, with implications for continuous cardiac monitoring where patient movement is unavoidable.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4505-9
Transition metal hydroxides are promising oxygen evolution reaction (OER) catalysts for alkaline water electrolysis. This study reports Ce-doped Co(OH)2 electrocatalysts synthesized via one-step electrodeposition, where the Ce3+/Ce4+ ratio is precisely controlled by deposition temperature. The optimized Ce-Co(OH)2 catalyst, obtained at 40°C, exhibits an overpotential of 236 mV at 10 mA cm-2 and maintains stability for 200 h. In an anion-exchange membrane water electrolyzer (AEMWE), the Ce-Co(OH)2 anode achieves a cell voltage of 2.04 V at 1 A cm-2 and operates for over 500 h at 500 mA cm-2. Mechanistic analysis reveals that Ce3+/Ce4+ dynamic electron buffering regulates surface reconstruction: during OER, electron transfer direction reverses (Ce → O → Co), with Ce donating electrons to Co sites to prevent over-oxidation and structural collapse. This work establishes a versatile strategy for balancing surface reconstruction and structural stability in Co-based OER catalysts, providing a foundation for designing high-performance, durable alkaline water oxidation electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4473-9
Selective ion separation is critical for resource recovery, water treatment, lithium extraction from salt lakes, and nuclear waste management, yet the differences in size, solvation structure, and coordination behavior among ions are often minimal, and separation is further complicated by valence, interfacial charge, and competing ions. Nanoporous materials with tunable sub-nanometer channels and chemically active interfaces can regulate ion entry, solvation reorganization, interfacial partitioning, intrapore migration, and release. This review examines three mechanistic categories—size and solvation sieving, chemical recognition, and dynamic gating—from the perspective of confined transport and ion–pore interactions, and compares their roles and coupling in systems of monovalent–monovalent, divalent–divalent, heterovalent, and chemically similar multivalent ions. We further distinguish selective adsorption, membrane enrichment, and transmembrane transport, and discuss how selectivity definitions, ion flux, feed composition, driving force, and operating time affect performance evaluation. Current research faces three major challenges: lack of comparability of performance data across different test conditions, insufficient direct evidence of ion solvation, site occupancy, and migration under operating conditions, and the complexity of feed streams. By adopting a sequential ion transport process as a unified conceptual framework, this review systematically compares separation mechanisms across diverse nanoporous materials, including MOFs, COFs, zeolites, 2D materials, microporous polymer membranes, ion-exchange membranes, biomimetic nanochannels, organic–inorganic composites, functionalized porous carbons, and biochars. This transport-process-oriented framework provides a general and mechanistic perspective for understanding and comparing selective ion separation across diverse nanoporous platforms.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4477-7
The rapid demand for high-energy-density lithium batteries necessitates advanced solid-state electrolytes (SSEs) to overcome the safety and performance limitations of conventional liquid counterparts. Macrocyclic compounds, with their well-defined cavities, programmable binding sites, and tunable self-assembly, have emerged as powerful molecular regulators for designing next-generation SSEs. This review examines recent advancements in macrocyclic compound-based SSEs by categorizing their functions into four fundamental supramolecular regulation paradigms: cation-centered regulation (e.g., crown ethers), anion-centered regulation (e.g., calixarenes and calixpyrroles), channel-dominated transport (e.g., cyclodextrins), and hybrid regulation (e.g., cucurbiturils). We elucidate how these macrocycles precisely control ion coordination, modulate migration dynamics, and reshape interfacial chemistry, leading to enhanced ionic conductivity, improved Li+ transference numbers, suppressed lithium dendrite growth, and superior interfacial stability. While each paradigm offers distinct advantages, the most promising SSEs often leverage synergistic combinations of these strategies. Finally, we highlight the remaining challenges, including synthetic complexity and multi-objective performance trade-offs, and propose future research directions for developing highly efficient and durable macrocycle-based solid-state lithium batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4313-7
Liquid-to-vapor mass transfer is central to energy and environmental processes. Conventional distillation relies on vapor-liquid equilibrium and device-level optimization, with materials playing passive structural roles. Non-boiling processes such as membrane distillation and interfacial solar evaporation localize phase change at confined interfaces, making mass transfer a materials-mediated transport phenomenon where interfacial structure and chemistry dictate evaporation kinetics, vapor escape, and solute rejection. Janus interface materials, featuring spatially separated hydrophilic and hydrophobic domains, introduce architectural asymmetry to regulate liquid-to-vapor mass transfer. This review summarizes recent advances, highlighting mechanisms including the cooperative pump-valve effect, nanoconfinement-enhanced transport, and mitigation of fouling and scaling. Representative applications in membrane distillation, solar-driven evaporation, and personal thermal-moisture management are systematically discussed. Key challenges and future opportunities are outlined, particularly in advancing fundamental understanding, scalable fabrication, and practical implementation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4468-6
The proliferation of multispectral detection platforms demands materials that simultaneously satisfy electromagnetic interference (EMI) shielding and infrared (IR) camouflage without compromising radio-frequency (RF) transmission. Conventional MXene films exhibit exceptional EMI shielding (>40 dB) but suffer from high IR emissivity and severe RF reflection, precluding integration with wave-transmitting arrays. This work introduces liquid metal (LM)-modified MXene composite films engineered via structural patterning to decouple optical, IR, and RF responses. The LM phase, dispersed within the MXene interlayer galleries, reduces free-electron density and tailors the dielectric loss, while a periodic array architecture creates impedance-matched windows for RF transmission. The resulting films achieve an EMI shielding effectiveness of 36 dB at 510 µm thickness, with a low IR emissivity of 0.36 and an RF transmittance exceeding 80% in the X-band. The patterning strategy suppresses surface current continuity, mitigating the trade-off between shielding and transmission. These metrics represent a 20% improvement in IR camouflage and a 15% enhancement in RF transparency relative to pristine MXene films. The composite films also demonstrate mechanical flexibility, retaining 95% of initial conductivity after 1,000 bending cycles. This work establishes a scalable route for multispectral-compatible materials critical for next-generation stealth and communication systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4294-4
Room-temperature phosphorescence (RTP) polymer materials are attractive for flexible electronics and information encryption due to their tunability and processability. However, achieving polymeric RTP systems that simultaneously exhibit high thermal sensitivity, reversible multicolor emission, and long phosphorescence lifetime (τPhos) with high quantum yield (ΦPhos) remains challenging. Here, we report an in-situ cross-linked self-assembly strategy that converts flexible polymers into rigid polymer microspheres, yielding long τPhos, high ΦPhos, and thermally and time-dependent tunable RTP. The resulting microspheres (PM0.1-0.01-1) exhibit a maximum τPhos of 1754 ms and ΦPhos of 42.83%, markedly superior to previously reported intrinsic polymer RTP materials. At 77 K, they display ultralong green emission with a lifetime of 6019 ms and visible afterglow lasting up to 99 s. The cross-linked microspheres enable time-dependent, continuously tunable RTP and thermally responsive color switching, while maintaining excellent phosphorescence stability in aqueous and high-temperature environments. This provides a versatile platform for dynamic information encryption, full-color afterglow LEDs, and temperature sensing. The strategy establishes a general design principle for developing multidimensional, controllable, and stable high-performance polymer RTP materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4502-1
Near-infrared-II (NIR-II, 1000-1700 nm) luminescent materials are pivotal for deep-tissue bioimaging and optical communication, yet their performance is often limited by low quantum yields and thermal quenching. Here, we report a thermal-enhanced NIR-II luminescence in Sb3+/Er3+ co-doped Cs3GdCl6 microcrystals synthesized via a modified Bridgman method. Under ultraviolet excitation, the co-doped microcrystals exhibit intense NIR-II emission centered at 1532 nm corresponding to Er3+: 4I13/2 → 4I15/2 transition, with a maximum relative sensitivity of 1.2% K−1 at 303 K. Notably, the integrated NIR-II emission intensity increases by 2.3-fold from 298 K to 373 K, demonstrating anomalous thermal enhancement. This behavior is attributed to the thermally activated energy transfer from Sb3+ sensitizers to Er3+ activators, as confirmed by temperature-dependent photoluminescence spectra and decay kinetics. The energy transfer efficiency reaches 86% at room temperature and further improves with rising temperature. The microcrystals also show excellent photostability, retaining 95% of initial intensity after 120 min continuous UV irradiation. Furthermore, we demonstrate a proof-of-concept wireless optical communication link using the microcrystals as a NIR-II phosphor, achieving a signal-to-noise ratio of 30 dB at 400 Hz modulation frequency. These findings provide a new strategy for designing thermal-enhanced NIR-II luminescent materials and expand their potential in temperature sensing and optical communication.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4295-5
Carbon nanomaterials (CNMs), including carbon nanotubes, graphene, and fullerenes, exhibit exceptional promise in precision biomedicine due to their tunable biocompatibility, programmable surface chemistry, large specific surface area, and quantum confinement effects. However, their clinical translation is hindered by aggregation, poor physiological dispersibility, and limited targeting specificity. This review systematically elaborates on surface engineering strategies—covalent functionalization, non-covalent assembly, and heteroatom doping—to optimize the multifunctionality, biocompatibility, and targeting capabilities of CNMs at the nano-bio interface. We explore how engineered interfaces enable advanced applications in biosensing, stimuli-responsive drug delivery, multimodal bioimaging, antibacterial therapy, and regenerative tissue engineering. The review also addresses challenges such as scalability, long-term toxicity, and regulatory hurdles, and proposes future directions to expedite clinical adoption. By providing a comprehensive framework for rational surface design, this work aims to bridge the gap between fundamental materials science and clinical needs, offering a roadmap for developing next-generation carbon-based theranostics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4300-3
The power conversion efficiency (PCE) of organic solar cells (OSCs) has surpassed 21% with the donor polymer D18, yet its processing from non-halogenated solvents like ortho-xylene (o-XY) remains inefficient due to uncontrolled film formation kinetics. Here, we systematically synthesize D18 polymers with molecular weights ranging from 41.6 kDa to 70.9 kDa to modulate crystallization kinetics. In-situ film drying studies reveal that lower molecular weights accelerate solidification, leading to excessive aggregation, while higher molecular weights slow it, causing insufficient phase separation. A medium molecular weight (D18-M) achieves a balanced crystallization rate, promoting favorable morphology and yielding a PCE of 20.55% with L8-BO as acceptor—one of the highest reported for non-halogenated solvent-processed OSCs. Energy loss analysis indicates that although low-molecular-weight polymers exhibit higher intrinsic luminescence, the blend film's emission is governed by exciton environment, which is dictated by morphology. This work underscores the critical role of molecular weight in controlling film formation and morphology, offering a simple yet effective strategy for high-efficiency, environmentally friendly OSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4192-y
Electrochemical water splitting is pivotal for scalable green hydrogen production, yet its practical deployment hinges on cost-effective electrocatalysts with high activity and durability. This study introduces a low-cost, three-dimensional (3D) nanoporous ZrVFeCoNi material fabricated via chemical dealloying, at merely 0.16% of the cost of Pt. The structure-activity relationship between its microstructure and hydrogen evolution reaction (HER) performance was systematically explored. Lattice defect effects from multiphase intermetallic compounds, combined with multi-metal synergy, optimize H+ adsorption energy and electron transfer kinetics. The 3D nanoporous architecture provides a high electrochemical surface area with abundant active sites, enhancing electrolyte penetration and reducing interfacial mass transfer resistance. Consequently, the ZrVFeCoNi electrode exhibits outstanding HER performance, requiring only a 38 mV overpotential to reach 10 mA cm−2 and maintaining stable operation for 1000 h at 500 mA cm−2. Integrated into a full water electrolyzer (ZrVFeCoNi || IrO2/Ni), the system achieves a cell voltage of 1.60 V at a current density of 400 mA cm−2. Advanced characterization and density functional theory (DFT) calculations reveal that interfacial interactions and charge transfer at heterointerfaces drive catalytic activity, showcasing the potential of 3D nano-structured multiphase intermetallic compounds as high-performance electrocatalysts for green hydrogen systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4322-4
Ultrafast scintillators with low-nanosecond emission are essential for next-generation high-rate X-ray and particle imaging. Although Ce3+-activated scintillators inherently exhibit fast response characteristics, conventional Ce3+-doped hosts rarely achieve low-nanosecond ultrafast decay. Here, we report a high-entropy fluoride scintillator (HEFS), Ce:LaGdCaSrBaF12 (Ce:LGCSB), in the form of bulk single crystals. The severe lattice distortion arising from multi-cation disorder induces exciton localization and effectively suppresses exciton diffusion. Through the rapid relaxation of localized excitons, the high-entropy Ce:LGCSB single crystals deliver a decay time of 1.23 ns with a 94.6% fast-component contribution and without any noticeable slow component. Through first-principles calculations, spectroscopic characterization, and transient dynamics analysis, we reveal that the ultrafast response originates from accelerated Frenkel exciton (FE) recombination enabled by the high-entropy environment. This work establishes entropy-engineered fluorides as promising ultrafast scintillator platforms and proposes a general strategy for extending sluggish diffusion effects to the excitonic scale, offering new opportunities for improving scintillation timing performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3696-3
The development of substitutable meniscus implants that can effectively protect articular cartilage remains a great challenge. Herein, a polyurethane with chemical crosslinking and sulfobetaine extenders containing hydrophobic chains (PU-CL-hSB) is developed, which could improve comprehensive properties and long-term stability simultaneously. By regulating the mole ratio of functional groups, PU-CL-hSB with appropriate mechanical properties, excellent tribological properties, and good fatigue resistance is used to prepare substitutable meniscus implant by hot-pressing. Due to the synergistic effect of functional groups, PU-CL-hSB meniscus implant presents comparable or even superior properties to native meniscus. It withstands a maximum force of 26.08 N versus 25.14 N for native meniscus, an energy dissipation from 45.93 to 39.17 N mm compared to 28.83 to 19.11 N mm for native meniscus over 300 cycles, and a friction coefficient from 0.08 to 0.19 compared to 0.11 to 0.26 for native meniscus. This PU-CL-hSB meniscus implant is further implanted into live rabbit knee joints for 8 and 25 weeks by a new approach, and in vivo data indicate that PU-CL-hSB meniscus implant not only protects articular cartilage from severe damage without eliciting inflammatory responses, but also can maintain normal physiological activities in the native state. Our findings present a substitutable meniscus implant that could be applied in vivo and propose evaluation methodologies for meniscus implants.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4110-9
Flexible tactile sensors are pivotal for human-machine interaction, yet accurate decoupled sensing of three-dimensional (3D) forces and integration into functional systems remain challenging. Here, we present a piezoresistive 3D force sensor based on ionic hydrogels that detects and analyzes multi-directional forces. The sensor exhibits a linear response to normal forces from 1 to 25 N (R²=0.99) and maintains stable sensitivity for shear forces within 0–4 N. By incorporating both force magnitude and direction, the sensor enables multidimensional password input, expanding traditional one-dimensional passwords into numeric, alphabetic, and Morse code formats. Experimental results demonstrate significant potential for enhancing information security. The sensor's simple structure, mature fabrication, and ease of integration with flexible electronics underscore its practicality. This work addresses the bottleneck of unidirectional sensing in conventional flexible pressure sensors, offering a robust solution for multidimensional force acquisition in human-machine interfaces, soft robotics, and biomechanical monitoring.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3848-7
Conventional heterogeneous photocatalysts often suffer from insufficient light absorption, rapid charge recombination, and a lack of specific reactive sites for efficient photocatalytic oxidation. To overcome these limitations, we propose a molecular polarization engineering approach utilizing structurally well-defined donor (D)-acceptor (A) covalent triazine frameworks (CTFs). The construction of dipole-induced built-in electric fields within the D-A-structured CTFs enables enhanced exciton dissociation and facilitates directional charge transfer. Specifically, the asymmetric A1-D-A2 moiety enhances molecular polarization in the dual-acceptor system CTF-TBT (A1-D-A2), enabling efficient charge separation through multiple electron-withdrawing units. This structural design promotes directional electron transfer toward the secondary acceptor (benzothiazole, A2), while simultaneously concentrating holes on the donor unit. Consequently, the A2 moiety acts as a site for efficient O2 activation via electron accumulation, whereas the highly oxidized donor unit provides strongly positive holes (h+) that facilitate substrate oxidation. Experimental and DFT calculation results confirm that CTF-TBT demonstrates highly enhanced photocatalytic oxidation performance, which can be attributed to its multi-channel charge separation mechanism and spatially separated redox-active sites. This study highlights the effectiveness of molecular dipole engineering in designing heterogeneous photocatalysts with controlled charge transfer pathways and improved redox capabilities. The proposed design principles provide a universal approach for promoting solar-driven chemical synthesis applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3615-1
Stretchable electronics are pivotal for bio-integrated devices, soft robotics, and wearables, yet their development is constrained by single-layer architectures that limit integration density and by mechanical mismatch between rigid components and soft substrates, which curtails service life. Here, we introduce a LEGO-like modular assembly strategy to construct multilayer three-dimensional (3D) stretchable electronics. Electronic components (ECs) and self-healing polyurethane (SPU) substrates patterned with liquid metal (LM) circuits serve as the modular blocks. This design simplifies fabrication and markedly enhances 3D integration density. The combination of LM circuits and self-healing elastic substrates enables devices to withstand diverse deformations and to autonomously heal after mechanical damage. Notably, the devices can undergo multiple recycling and reuse cycles without significant performance loss. This methodology offers a new paradigm for advanced flexible electronics, addressing critical bottlenecks in integration density, mechanical robustness, and sustainability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3666-2
Light-emitting electrochemical cells (LECs) are promising for low-cost, solution-processed display and lighting applications, yet achieving high efficiency and color purity remains challenging. Here, we report two ionic multi-resonance (MR) emitters with narrowband blue emission for high-color-purity LECs. By covalently bonding an imidazolium functional group into a boron/nitrogen-doped polycyclic skeleton, the emitters retain the narrowband emission and high photoluminescence quantum yield (PLQY) of the MR core while gaining ionic character. The design exploits two types of nitrogen atoms in the imidazolium unit: the pyrrolic N at the 1-position forms a para-B-π-N linkage, elevating excited-state energy levels and blue-shifting emission; the pyridinic N at the 3-position provides a quaternization site, yielding intrinsically ionic emitters compatible with ionic hosts. The emitters exhibit blue emission with narrow full-width at half-maximum of 26–27 nm and high PLQYs of 95%–97% in solid-state films. LECs based on these emitters achieve narrowband blue electroluminescence with CIE coordinates of (0.12, 0.26) and a maximum external quantum efficiency (EQE) of 4.6%, representing the first narrowband blue LECs based on intrinsically ionic MR emitters. This work demonstrates a viable molecular design strategy for high-color-purity LECs, addressing the long-standing trade-off between efficiency and color purity in this technology.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3654-5
Hydrogen production by photosynthetic green algae is an efficient biological process that utilizes light energy to convert water and carbon dioxide into clean and renewable energy. In this paper, we constructed a hybrid system combining graphitic carbon nitride (g-C3N4) and Chlorella pyrenoidosa (Chlorella), in which g-C3N4 serves as an extracellular electron source and Chlorella acts as a biological reactor for specific hydrogen production. In particular, the electronic structure of carbon nitride was optimized by means of hydrothermal alkalization and copper ion doping, expanded the light absorption range and enhanced the light response ability. g-C3N4, as an extracellular electron source, can provide electrons for Chlorella to improve hydrogen production performance which is 3.7 times that of bare Chlorella. The construction of a biological hybrid system is a feasible optimization strategy for the hybrid system to promote the synergistic effect of the hybrid system by regulating the properties of non-living components.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3748-9
Direct regeneration is a sustainable solution for recycling spent lithium-ion batteries (LIBs), yet the irregular strains induced by the irreversible FePO4 phase after cycling hinder Li+ replenishment in spent LiFePO4 cathodes. This study proposes a lattice stress modulation strategy that reduces FePO4 to Fe2P2O7, reducing unit cell volume from 271.7 to 122.6 Å3, releasing residual stress and reconstructing continuous Li+ transport channels. The phase transformation reconstructs FeO6 octahedra, lowering the migration energy barrier for ions. This synergistically weakens steric effects, facilitating Li+ replenishment and eliminating Li-Fe anti-site defects. Regenerated LiFePO4 cathodes achieve 80.2% capacity retention after 1000 cycles at 2C, outperforming commercial cathodes. The work establishes fundamental principles for the pre-treatment stage of direct regeneration and provides a paradigm-shifting solution for sustainable LIB recycling.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3689-9
Converting body heat into electricity presents an appealing route for sustainably powering wearable electronics; however, conventional thermoelectric materials face significant drawbacks, including high ionic concentrations, toxicity, and limited thermoelectric efficiency. Here, we report an ionic thermoelectric hydrogel designed through precise supramolecular chemistry, utilizing dual molecular interactions: host-guest complexation of α-cyclodextrin (α-CD) with I3− ions and hydrogen bonding between polyvinyl alcohol (PVA) polymer chains and I3−. This molecularly tailored approach markedly amplifies thermoelectric performance, achieving a high thermopower of 2.21 mV/K and a tenfold enhancement in peak power output at an exceptionally low iodine concentration (10 mmol/L I− + 2.5 mmol/L I3−). The hydrogel maintains excellent biocompatibility and mechanical robustness, suitable for direct skin contact. Demonstrated applications include flexible thermoelectric devices generating nearly 100 mV from body heat and sensor arrays capable of motion and spatial temperature sensing. These results underscore the substantial potential of supramolecularly designed ionic thermoelectric hydrogels for wearable energy harvesting, personalized healthcare monitoring, and advanced human-computer interfaces.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3730-3
Water scarcity, exacerbated by organic micropollutant contamination and climate change, necessitates energy-efficient, eco-friendly purification technologies. Membrane separation has emerged as a transformative solution, outperforming energy-intensive processes such as distillation. Traditional chemical separations, dominated by distillation, consume 10%–15% of global energy, whereas advanced membrane technologies can reduce energy use by up to 90%. However, membrane separation is hampered by reliance on toxic petrochemical feedstocks and persistent microplastic pollution from nonbiodegradable end-of-life membranes. Shao's group addresses both gaps with a sustainable nanofiltration membrane (SNFM) crafted entirely from low-hazard, renewable components. The substrate polylactic acid (PLA), a biodegradable polyester derived from corn starch, is processed via modified nonsolvent-induced phase separation (NIPS) to form a porous yet strong support. For the selective layer, toxic aromatic monomers are replaced with xylitol (a plant sugar alcohol) and dopamine (DA, a biogenic amine), and green solvents such as dimethyl sulfoxide are used to avoid volatile organic compound emissions. Compared with commercial alternatives, this design yields a membrane with exceptional dual functionality: it maintains high separation performance (928% greater permeance, 92% bisphenol A rejection, and 89% Na2SO4 rejection) and low fouling (protein adsorption ≤12 μg cm−2) over 30 days. A life cycle assessment reveals a 62% reduction in carbon footprint compared with petrochemical-based membranes, whereas soil biodegradation tests confirm 90% breakdown within 6 months, driven by Delftia and Tissierella microbes. By eliminating microplastic waste and toxic inputs, this SNFM bridges the divide between performance and environmental responsibility, offering a scalable blueprint for next-generation green membranes in water treatment and beyond.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3767-9
Progressive skin fibrosis ultimately results in irreversible contractures, causing both joint dysfunction and cosmetic deformity. The key pathological features of skin fibrosis include persistent inflammation and abnormal accumulation of the extracellular matrix (ECM), with epithelial-mesenchymal transition (EMT) playing a critical role in disease progression. However, current therapeutic strategies for cutaneous fibrosis are largely palliative and often require repeated interventions, with limited efficacy. Celastrol (Cel) exerts anti-inflammatory and anti-fibrotic effects in skin tissue, but its clinical application is limited by poor bioavailability and a narrow therapeutic window. Tetrahedral framework nucleic acid (tFNA), a novel nanocarrier system, exhibits multiple advantages, including enhanced cellular uptake, improved cell viability, and intrinsic anti-fibrotic and anti-inflammatory properties. Therefore, this study applied tFNA-Cel complex (TCC) as an advanced nanotherapeutic agent, designed to exert a synergistic anti-fibrotic effect. In this study, an in vitro model of skin fibrosis was established using human keratinocyte (HaCaT) cells treated with 5 ng mL−1 transforming growth factor beta (TGF-β) for 24 h. The results showed that TCC significantly inhibited EMT progression by reducing α-smooth muscle actin (α-SMA) levels and increasing E-cadherin level. Compared to tFNA or Cel alone, TCC exhibited superior anti-fibrotic effects in the fibrosis model, as evidenced by modulation of SMAD family member 2 (SMAD2) signaling and collagen I expression. Furthermore, the TCC group showed lower levels of nuclear factor κB p65 (NF-κB p65), BCL-2-associated X protein (Bax), and reactive oxygen species (ROS) compared to the Cel or tFNA groups. These findings highlight TCC as a promising treatment for skin fibrosis, with its synergistic anti-fibrotic effects providing new therapeutic avenues.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025122102
Uranium is a key resource for nuclear energy, but its mining and processing generate large amounts of uranium-containing wastewater, posing persistent threats to the environment and human health. In this study, a cyano-functionalized C3N4/ZnIn2S4 (CCN/ZIS) heterojunction system was constructed for efficient removal of U(VI) from uranium mining wastewater. The introduction of cyano groups significantly enhanced the adsorption capacity of CCN/ZIS, reaching a maximum of 123.65 mg·g−1. Characterization techniques (UV-vis DRS, EIS, i-t, PL, TRPL) confirmed that cyano groups effectively suppress charge carrier recombination, improving photogenerated carrier separation. Under visible light, the modified material achieved over 95% removal of U(VI) within 10 minutes, demonstrating a 20-fold efficiency increase compared to pristine materials. Even in simulated uranium mining wastewater containing high concentrations of CO3^2− and F−, CCN/ZIS maintained excellent performance, overcoming the technical challenge of U(VI) removal efficiency being constrained by water quality conditions. Quenching experiments identified e− and ·O2− as the primary reactive species responsible for U(VI) reduction. This study reveals the synergistic mechanism of selective U(VI) enrichment and photoreduction, providing theoretical innovation and technological breakthroughs for uranium pollution control.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3449-5
The escalating demand for high-performance lithium-ion batteries (LIBs) in portable electronics and electric vehicles has driven extensive research into advanced electrolytes. Ionic liquids (ILs) and their derived electrolytes, including poly(ionic liquids), ionogels, and IL-functionalized systems, offer significant potential for enhancing the safety and electrochemical performance of LIBs due to their unique properties such as non-volatility, wide electrochemical windows, and excellent thermal stability. These properties enable safer, high-energy, and long-lasting batteries. This review conducts a thorough analysis of the physicochemical properties of ILs and their versatile applications in electrolytes, particularly emphasizing their adaptability to fulfill the specific needs of different battery systems. In liquid electrolyte systems, ILs can function as solvents, interfacial modifiers, and critical components for constructing artificial solid electrolyte interphase (SEI). In (quasi-)solid-state electrolyte systems, ILs can be polymerized to form poly(ionic liquid)s or integrated with organic, inorganic, or composite materials to develop IL-based electrolytes, demonstrating multifunctional electrochemical performance. Finally, the review critically examines the challenges and opportunities in this field, offering insightful perspectives for future advancements.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61094-3
Aqueous zinc-iodine (Zn-I2) batteries are promising for large-scale energy storage due to their intrinsic safety, low cost, and high theoretical capacity (211 mAh g−1 for iodine). However, their practical application is hindered by the poor electronic conductivity of iodine, sluggish redox kinetics, and the shuttle effect of polyiodides. This review systematically analyzes the reaction mechanisms of iodine cathodes, including two-electron (I−/I2) and multi-electron (I−/I2/I+ and I−/I2/I+/IO3−) pathways, and identifies key bottlenecks. It then comprehensively summarizes recent advances in iodine host materials, categorized into three strategies: physical confinement, chemical adsorption, and electrocatalysis. Representative host materials such as porous carbons, covalent organic frameworks (COFs), porous aromatic frameworks (PAFs), polymers, MXenes, and Prussian blue analogs (PBAs) are discussed, with emphasis on the structure–performance relationships. The review highlights that heteroatom doping (e.g., nitrogen) enhances chemical adsorption of iodine species, while single-atom catalysts (e.g., Co, Zn) provide electrocatalytic sites that accelerate conversion kinetics. Finally, future research directions are proposed, including exploration of multi-electron systems, mechanistic elucidation of iodine conversion, development of advanced host materials, and optimization of zinc anodes, to accelerate the commercialization of Zn-I2 batteries.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510089
Microplastics (MPs) are frequently detected in various water bodies, posing increasing environmental risks. This study synthesized magnetic Fe3O4@MIL-100(Fe) microspheres via an in-situ one-step hydrothermal method and investigated their adsorption removal mechanisms for polystyrene (PS) and polylactic acid (PLA) microplastics. The composite exhibited a core-shell structure with a high specific surface area of 848.6 m2·g−1. Adsorption kinetics showed that PLA followed a pseudo-second-order model, while PS fitted both pseudo-first-order and pseudo-second-order models. Equilibrium data for both MPs were well described by the Freundlich isotherm. Removal efficiencies for PLA and PS increased from 58.18% and 49.66% to 98.90% and 98.58%, respectively, as pH decreased, and from 64.24% and 21.58% to 97.05% and 94.63% with increasing ionic strength. The removal mechanism involved synergistic physical-chemical interactions: hydrogen bonding dominated for PLA, with some complexation, while π–π interactions and hydrogen bonding were primary for PS. The material demonstrated excellent reusability over multiple cycles. These findings highlight the potential of Fe3O4@MIL-100(Fe) for efficient removal of MPs from water, offering a novel approach for controlling emerging contaminants.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508047
Selective recovery of aluminum compounds from fly ash is a key route for its high-value utilization. This study developed a multi-stage activation process for extracting Al(OH)3 from fly ash, comprising mechanical activation, calcination activation, chemical separation, and carbonation precipitation. Fly ash was mixed with carbide slag and CaF2, then calcined; the resulting clinker was leached with Na2CO3 solution to extract Al. The CaO generated from high-temperature calcination of carbide slag facilitated the separation of Si and Al. After solid-liquid separation, CO2 was introduced into the Al-rich leachate to precipitate Al(OH)3. The process promoted the formation of Ca12Al14O32F2 and inert Ca2SiO4, achieving efficient Si-Al separation during calcination. Under optimal conditions (mechanical activation for 60 min, 4% CaF2, calcination at 1000°C for 2 h, leaching with 40 g/L Na2CO3), the Al extraction rate reached 91.8%, and the product purity was 98.9%. The alumina extraction residue exhibited porous and highly reactive characteristics, suitable for producing flame-retardant materials or high-value silicon-based products (e.g., white carbon black, molecular sieve adsorbents). The process offers a promising industrial route for fly ash valorization, with potential integration with cement production lines for synergistic CO2 capture and utilization.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0029
Pingshuo coal ash, characterized by high silicon-aluminum content (Si+Al >85%) and low Si/Al ratio (<1.5), exhibits ash fusion temperatures (AFTs) exceeding 1550 °C, rendering it unsuitable for entrained-flow gasifiers. This study investigates the effect of calcium-sodium composite flux on ash fusibility and mineral transformation. X-ray diffraction (XRD) and FactSage thermodynamic simulations were employed to analyze mineral evolution, while molecular dynamics (MD) simulations revealed the underlying melting mechanism. Results show that adding 20% composite flux (CaO/Na2O) lowers AFTs more effectively than equivalent additions of CaO or Na2O alone, indicating a synergistic effect. At a CaO/Na2O ratio of 3:7, the flow temperatures (FT) of two Pingshuo coal ashes decreased to 1377 °C and 1279 °C, respectively. The composite flux promotes reactions between quartz and Na2O/CaO, forming low-melting-point minerals such as nepheline, albite, and gehlenite, while inhibiting mullite formation. Additionally, Na+ disrupts the silicate network, inducing Ca2+ to preferentially coordinate with [AlO4]5- tetrahedra, further breaking Si-O-Si bonds. MD simulations show that atomic diffusion, quantified by mean square displacement (MSD), is significantly enhanced below 1600 K with composite flux addition compared to single fluxes. These findings provide a mechanistic basis for optimizing flux formulations to enable efficient gasification of high-AFT coals.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010306
Sulfur autotrophic denitrification (SAD) has attracted increasing attention due to its low cost, no need for external carbon sources, and low sludge production. This review systematically examines the reaction principles and key material elements of various electron donors for SAD, including elemental sulfur, sulfide, thiosulfate, and iron sulfide. It discusses recent research progress on different SAD processes and the influence of environmental factors. A comparative analysis between heterotrophic denitrification and SAD highlights SAD's advantages in reaction rate, secondary pollution, and cost-effectiveness, underscoring its promising application prospects. Notably, iron sulfide-based autotrophic denitrification maintains stable pH and produces fewer by-products (e.g., sulfate, nitrous oxide). When developed into an aggregate sulfur concrete system, it can purify nitrogen and phosphorus from secondary effluent standards to Class IV surface water standards within a hydraulic retention time of only 0.5–2 hours, addressing the contradiction between SAD reaction rate and engineering demands. This enables efficient simultaneous nitrogen and phosphorus removal, making it viable for groundwater remediation, advanced wastewater treatment, eutrophication control, and deep nitrogen removal. The national 'Dual Carbon Strategy' (carbon neutrality and peak) positions SAD as a promising method for wastewater treatment plants to meet increasingly stringent nitrogen and phosphorus discharge standards.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025020901
The intensification of environmental pollution necessitates the development of efficient and sustainable remediation technologies. Piezoelectric-coupled photoelectrocatalysis and piezoelectric-coupled electrocatalysis, which convert mechanical energy into electrical energy and integrate with photoelectrocatalytic or electrocatalytic processes, have demonstrated significant potential for environmental remediation. By combining the piezoelectric effect of piezoelectric materials with photocatalysis or electrocatalysis, these technologies markedly improve the separation efficiency of photogenerated or electrogenerated electron-hole pairs, thereby enhancing pollutant degradation. This review explores the working principles of piezoelectric-coupled photoelectrocatalysis and electrocatalysis, highlighting their latest advancements in environmental remediation, including the degradation of organic pollutants and value-added conversions. It also addresses the challenges currently faced in applying these technologies, such as limitations in light transmittance, restricted light absorption ranges, rapid carrier recombination, and the short lifespan of electrodes in electrochemical systems. Finally, potential future research directions are discussed, emphasizing the need for improved material stability, scalable synthesis methods, and a deeper mechanistic understanding to bridge the gap between laboratory research and practical applications.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025091205
This study analyzes the spatiotemporal variation characteristics and driving mechanisms of PM2.5, PM10, SO2, NO2, O3, and CO in the Kuytun-Dushanzi-Wusu (Kui-Du-Wu) region of Xinjiang, based on monitoring data from 2018 to 2024. Results indicate that urban sites (e.g., Kuytun Laoganju Station) are influenced by traffic emissions, leading to elevated PM2.5 and NO2 concentrations. Dushanzi District, with petrochemical industry emissions, exhibits notable SO2 and O3 pollution. Agricultural areas (e.g., Kuytun Huaxin Tomato Company) show significant PM10 and CO levels affected by dust and diesel machinery. Over the study period, PM2.5, PM10, NO2, and CO concentrations generally declined at annual rates of 1.5–4.0 μg·m−3·a−1, reflecting the effectiveness of coal substitution, industrial upgrades, and vehicle emission controls. Conversely, O3 concentrations increased consistently at rates of 1.3–3.2 μg·m−3·a−1, highlighting shortcomings in volatile organic compound (VOCs) control. Seasonal patterns show PM and CO peaking in winter due to heating combustion and temperature inversions, and reaching minima in summer due to enhanced diffusion and precipitation. O3 peaks in summer driven by photochemical reactions, contrasting with NO2 winter highs from heating and industrial activities. The findings underscore the need for coordinated control of VOCs and NOx, optimized dust management, and differentiated emission controls for industrial, traffic, and agricultural sources.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605007
Reservoirs are significant sources of nitrous oxide (N2O), a potent greenhouse gas. The nosZ-type denitrifying bacteria, which reduce N2O to inert N2, play a critical role in mitigating emissions. This study investigated the community structure, diversity, and abundance of nosZ-type denitrifiers in surface sediments (0-15 cm) from 18 reservoirs in the northeastern Qinghai-Tibet Plateau, including 10 in the Yellow River mainstem and 8 in the Huangshui River basin. Sampling occurred during dry (May 2023) and wet (August 2023) seasons. High-throughput sequencing of the nosZ gene and quantitative PCR were employed. Results showed that Proteobacteria dominated (78.91%). Paracoccus and Halomonas were biomarkers in the Yellow River mainstem. Diversity was significantly higher in the Huangshui basin (P<0.05), with no temporal difference. Gene abundance was higher in the Huangshui basin (165.24×10^5 copies/g) than in the Yellow River mainstem (34.43×10^5 copies/g), and higher in wet season (128.55×10^5 copies/g) than dry season (61.27×10^5 copies/g) (P<0.05). Redundancy analysis and hierarchical partitioning identified sediment temperature, pH, total phosphorus, and water total nitrogen as key drivers, explaining 17.14%, 16.89%, 13.83%, and 11.23% of community variation, respectively. These findings reveal significant spatiotemporal heterogeneity and provide a scientific basis for N2O mitigation in plateau reservoirs.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225225
The non-Newtonian rheological properties of plastic melts are critical for regulating plastic processing, molding, and recycling processes, ensuring processing stability and product performance. However, rheological data for commonly used plastics and their blends remain incomplete. This study combined experimental testing and theoretical modeling to investigate the rheological behaviors of four pure plastics—polypropylene (PP), polyethylene (PE), polystyrene (PS), and acrylonitrile-butadiene-styrene copolymer (ABS)—and three binary blend systems: PE/ABS, PP/ABS, and PS/ABS. Rheological tests were conducted using a rheometer over a shear rate range of 0.1–100 s⁻¹ and temperatures from 180°C to 250°C. Results showed that the flow behavior index n was less than 1 for all samples, and apparent viscosity decreased significantly with increasing shear rate, indicating clear shear-thinning behavior. The consistency coefficient K followed the Arrhenius relationship with temperature, and melt viscosity decreased as temperature increased. The study quantitatively characterized the relationship between the mass fraction m (0.5 < m ≤ 1) of the main component in binary blends and melt viscosity. Based on experimental data, a component correction term was introduced into the traditional power-law model to construct a constitutive equation that simultaneously describes the effects of shear rate, temperature, and component fraction on melt viscosity. The average relative error between model predictions and experimental values was only 5.90%. These rheological data and the modified constitutive equation provide important theoretical support and data reference for optimizing process parameters in waste plastic recycling and injection molding.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3817-3
The rapid development of artificial intelligence (AI) and big data-driven edge intelligence applications has created an urgent demand for highly efficient computing hardware. Ferroelectric memristors have emerged as promising candidates for edge hardware due to their multi-level conductance tunability and high integration potential. In this work, we fabricated yttrium-doped hafnium oxide (YHO) memristors with a remanent polarization of ~30 μC/cm2, a multi-level resistive state retention time of approximately 10^5 s, and an endurance of up to 10^9 cycles. Based on this device, we constructed a real-time path-tracking system for intelligent vehicles—which achieves 100% path recognition accuracy—and a traffic sign denoising network optimized for hardware mapping via a hierarchical mixed-precision quantization strategy; this network yields denoised images with a peak signal-to-noise ratio (PSNR) of 27.04 and a structural similarity index measure (SSIM) of 0.80. This work paves an innovative pathway for the practical application of hafnium-based ferroelectric memristors, accelerating the development of highly efficient hardware for edge intelligence.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509124
To reveal the spatiotemporal evolution and driving mechanisms of water quality in the Hanjiang River Basin, this study utilized monthly water quality monitoring data from 54 sections from January 2021 to April 2024. Methods including single-factor index, comprehensive water quality index (WQI), principal component analysis (PCA), and optimal parameters-based geographical detector (OPGD) were employed. Results indicated significant spatiotemporal differences, with total nitrogen (TN), chemical oxygen demand (COD), and permanganate index (CODMn) as major pollutants, TN being the most critical. Temporally, agricultural non-point source organic pollution dominated in wet season, while comprehensive organic pollution with industrial point source characteristics prevailed in dry season. Spatially, water quality deteriorated along the main stream, with tributary downstream areas showing severe pollution, forming a pattern of 'mountainous areas good, plains poor'. OPGD revealed combined effects of natural conditions and human activities, proposing a 'zonal control and targeted treatment' strategy.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511090
In ecological restoration projects such as wetland reconstruction and mine reclamation, seedling transplantation or mechanical damage often leads to slow healing, reducing survival rates and weakening carbon sequestration and soil-water conservation functions. To address secondary pollution from traditional chemical remediation, this study developed a self-powered piezoelectric hydrogel for green electrical stimulation of plant wounds. The hydrogel, based on polyacrylamide/polyethylene glycol (PAM/PEG) with CaCl2, formed a microporous, locally ordered piezoionic network. Characterization included microstructure, piezoionic response, and water retention. At 30 °C and 55% relative humidity, the hydrogel retained about 70% mass after 80 h of continuous water loss. Under simulated environmental mechanical forces, the hydrogel generated a peak voltage of approximately 6 mV. In tomato seedling stem models, wound callus area ratios reached approximately 49.50%, 64.87%, and 86.13% at 3, 5, and 10 days, respectively, when the hydrogel was attached and driven by environmental forces. The PAM/PEG/CaCl2 hydrogel efficiently converts environmental mechanical energy into mild electrical signals, promoting plant wound healing, reducing exogenous chemical use, and offering a low-carbon, environmentally friendly material pathway for ecological restoration and urban green space management.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510004
Ammonium salt crystallization-induced blockage of the regenerative heat exchanger in regenerative thermal oxidizers (RTOs) remains a critical operational challenge, particularly in pharmaceutical applications where NH4Cl constitutes up to 70% of the fouling deposits. This study employs computational fluid dynamics (CFD) to systematically simulate six purging configurations, varying injection angle and pipe arrangement, and quantifies purging effectiveness via a novel evaluation method based on characteristic observation planes. Using the Realizable k-ε turbulence model coupled with a porous media model, we analyze the velocity distribution and low-velocity failure zones at the gas chamber–regenerator interface. Results demonstrate that a single-pipe 45° oblique injection achieves the highest effective purging area of 57.6%, a 35.7% improvement over conventional horizontal purging. Increasing pipe diameter significantly enhances flow uniformity, yielding an efficiency gain of approximately 40%, outperforming mere increases in gas velocity. A synergistic optimization strategy is proposed, prioritizing high-performance purging structures with coordinated parameter tuning. The recommended configuration—single-pipe 45° injection, 280 mm pipe diameter, and 14 m·s−1 gas velocity—achieves 88.2% purging efficiency without additional fan power, representing a 45.6% improvement over conventional modes. These findings provide a theoretical basis and engineering solution for RTO purging system design and operational optimization.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510041
This study presents a full-scale engineering practice of retrofitting an idle upflow anaerobic sludge blanket (UASB) reactor into an aerobic granular sludge (AGS) system for treating low-strength municipal wastewater. The design capacity was 20,000 m3/d (maximum 24,000 m3/d), achieving separate treatment of industrial and domestic wastewater to reduce operational costs. Systematic analysis covered hydraulic capacity enhancement, effluent quality, pollutant removal efficiencies, sludge granulation progress, and operational costs. Results showed rapid start-up: the system reached 75% of design capacity by day 10 and 90% by day 26. During a 4-month operation, average removal efficiencies for COD, NH4+-N, TN, and SS were 83.2%, 97.0%, 75.9%, and 94.4%, respectively, even under low influent BOD5/TN ratios (typically below 4). Granulation progressed quickly: by day 44, average particle size was 2.6 times that of the inoculum and over 4 times that of flocs, with granules (>200 μm) accounting for 17.3%; by day 110, these values increased to 3.2 times and 5 times, with granule proportion reaching 33.4%. Compared to the previous year (June–August), the AGS process reduced electricity consumption, chemical consumption, and sludge production by 77.3%, 25.4%, and 30.4%, respectively, while saving 65.6% of footprint. This ten-thousand-ton case provides a practical basis for AGS technology application in China.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606002
Industrial volatile organic compounds (VOCs) emissions are a major contributor to regional air pollution, and the rubber paste preparation process is a significant source. This study developed an intelligent monitoring system for whole-process VOCs management in a rubber paste preparation workshop, integrating software engineering and Internet of Things (IoT) technologies. The system architecture combines a hybrid database (MySQL relational and InfluxDB time-series), MQTT-based low-power wide-area communication, role-based access control, and containerized microservices. Field deployment at a large rubber enterprise enabled real-time monitoring of adsorption/desorption centrifugal fans and data fusion analysis. Under typical operating conditions, the extraction and ventilation systems achieved volume flow rates of 40,000 m³/h and 30,000 m³/h, respectively, maintaining a continuous micro-negative pressure environment that effectively suppressed fugitive emissions. The purification process, comprising zeolite rotor adsorption and regenerative thermal catalytic oxidation, reduced non-methane hydrocarbon (NMHC) concentrations to below 10 mg/m³, meeting the GB 27632—2011 emission standard. The system's multi-level permission management module precisely allocated operational responsibilities across production, environmental, and management roles, reducing response time to abnormal conditions. An online evaluation model for purification efficiency was constructed based on the actual process. The system demonstrates potential for extension to other high-VOCs industries such as coatings and printing. This research provides theoretical and practical references for applying computer technology to VOCs reduction and whole-process management in typical industries.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606021
To provide a theoretical basis for energy-saving combustion of regenerative thermal oxidizers (RTOs), this study analyzes energy nodes during RTO operation, refines heat balance accounting, and establishes an overall energy system. Taking a three-chamber RTO as the research object, the enthalpy of exhaust gas at different stages is calculated, and a whole-process heat balance model is developed to systematically analyze exhaust gas preheating, combustion, heat recovery, and heat loss transfer. An improved energy accounting method is proposed to address dynamic heat exchange inside heat accumulators, coupling of multiple gas streams, and boundary heat loss under complex conditions. The longitudinal temperature distribution function of heat accumulators is introduced to overcome difficulties in heat accounting within the accumulator chamber. A thermodynamic system covering 11 key internal energy nodes is constructed. Combined with design characteristics of RTO operation across industries, the application scope of the overall energy system is analyzed; equilibrium terms can be adjusted according to actual conditions, ensuring wide applicability. Validation via an RTO energy system for a glove manufacturing plant demonstrates that outlet temperature prediction accuracy improves from 14.3% to 2.8%, providing a theoretical foundation for future intelligent energy-saving combustion research.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3863-x
Lead-free double perovskites are promising for optoelectronic applications due to their tunable optical properties, stability, and non-toxicity. However, achieving efficient ultrabroadband near-infrared (NIR) emission and X-ray radioluminescence (RL) simultaneously remains challenging. Here, we report a Mo4+-doped Cs2(Na0.4Ag0.6)InCl6 double perovskite that exhibits efficient blue-light-excitable NIR emission with a near-unity photoluminescence quantum yield. The emitter demonstrates robust thermal stability, retaining 84% of its initial emission intensity at 420 K relative to 300 K. Under X-ray irradiation, the material shows bright NIR RL with a high light yield of 39,400 ± 1100 photons/MeV. A flexible film of Mo4+-doped Cs2(Na0.4Ag0.6)InCl6/polydimethylsiloxane (PDMS) was fabricated and applied as an NIR light source and X-ray scintillator. A dual-functional platform for cooperative NIR and X-ray imaging was established using a bullfrog palm as the target, achieving pixel-level fusion of NIR and X-ray images without spatial mismatch or complex image processing. The fused image simultaneously visualizes blood vessels and skeleton textures under the skin tissue. This work provides a viable strategy for lead-free double perovskites in advanced optoelectronic devices, particularly for multispectral imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3842-8
The metal-support interactions (MSIs) play a significant role in regulating the electronic structure of metal species on oxide; however, they are often overlooked on carbon-based supports. In this work, hollow nitrogen-doped carbon (H-NC) supported Ru nanoparticles catalyst (Ru/H-NC) was prepared by a solvothermal method using H-NC as support and RuCl3 as precursor. Subsequently, Ru/H-NC was annealed at different temperatures (Ru/H-NC t °C) to adjust the effect of MSIs between H-NC support and Ru nanoparticles. The X-ray photoelectron spectroscopy results showed that the MSIs between Ru species and H-NC support increased with the increase of temperature, and more electrons were transferred from Ru species to H-NC support, thus regulating the valence state of Ru. In hydrogen evolution reaction (HER), the as-synthesized Ru/H-NC 300 °C merely requires overpotential of 35.45 mV to achieve 10 mA/cm2 at low Ru mass loading of 24.03 μg/cm2 on the glassy carbon electrode. The cyclic voltammetry test revealed that the electrochemically active surface area increased first and then decreased with the increasing MSIs. Moreover, electrochemical impedance spectroscopy results showed that HER kinetics of Ru/H-NC t °C catalysts increased first and then decreased with the MSIs enhancement. The density functional theory calculations confirmed that the MSIs effectively optimize the adsorption strength of the key intermediates (H*, HO*) on Ru clusters, and thus greatly improve the catalytic performance of Ru/H-NC in HER.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3809-y
The development of hydrogels that simultaneously achieve high strength and good toughness remains a critical challenge in soft material science, particularly for applications in flexible electronics, soft robotics, and biomedical devices. Conventional approaches often suffer from a trade-off between mechanical robustness and functional performance. In this work, we present a novel solvent-driven dual-network entanglement strategy to fabricate a strong and tough poly(vinyl alcohol) (PVA)-based organo-hydrogel by synergistically combining isopropanol (IPA) solvent substitution to induce dense polymer chain entanglement and a sodium alginate (SA) ionic crosslinked network as a dynamic energy-dissipation phase. The resulting organo-hydrogel exhibits excellent mechanical performance with a tensile strength of 3.18 MPa and a toughness of 16.65 MJ/m3, representing increases of approximately 17 and 49 times that of conventional PVA hydrogels, respectively. Furthermore, the organo-hydrogel displays superior swelling resistance and long-term stability in aqueous environments, enabling reliable operation in challenging conditions such as underwater motion sensing and wearable strain detection. Morphological analyses reveal the critical role of solvent-mediated chain reorganization and dual-network interactions in achieving these properties. This work not only provides a versatile platform for designing robust gel materials but also offers fundamental insights into solvent-network interactions for advanced soft material engineering.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3783-x
The synergistic strategy combining chemotherapy and immunotherapy has recently demonstrated significant promise in cancer treatment. However, the substantial physicochemical disparities between chemotherapeutic agents and small-molecule immune adjuvants pose considerable challenges for co-delivery strategies. In this study, we designed a reactive oxygen species-responsive paclitaxel prodrug, PTX-PBA, which markedly enhanced drug encapsulation stability and dual-drug loading efficiency by various polymeric delivery systems. The resultant nanosystem (NanoPR) exhibited excellent physicochemical properties and ROS-triggered release profiles, effectively inducing immunogenic cell death in tumor cells while promoting dendritic cell maturation and CD8+ T cells activation. In murine models of 4T1 breast cancer and CT26 colon carcinoma, NanoPR achieved significant tumor growth inhibition and elicited durable immune memory responses. Collectively, this work provides an innovative molecular design strategy for the co-delivery of chemotherapeutics and immunomodulators, offering a robust foundation for the clinical translation of chemo-immunotherapy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3873-7
The escalating demand for lightweight, multifunctional stealth materials in modern protective applications necessitates integrated solutions against electromagnetic interference (EMI), infrared (IR) detection, and incendiary threats. This study presents an innovative melamine foam (MF)-based composite featuring an asymmetric dual-nano conductive network, achieving absorption-dominated EMI shielding, IR stealth, and flame retardancy. Inspired by the Salisbury screen, the composite employs MF as an interlayer and flame-retardant thermoplastic polyurethane (TPU) nanofiber membrane as a substrate. The architecture comprises a carbon nanotubes (CNTs)-modified impedance matching nanofiber layer as the top absorber and a silver nanoparticles (AgNPs)-modified nanofiber layer as the highly conductive reflective bottom. Precise control of CNTs content and interlayer thickness enables tunable electromagnetic wave (EMW) absorption, yielding a low reflection coefficient of 0.03 and a high EMI shielding effectiveness of 79.23 dB at a total thickness of 4.40 mm. Even at 1.40 mm, effective absorption-dominated shielding is maintained. The performance remains stable under ultrasonic, compression, and bending tests, demonstrating high durability. The mechanism underlying absorption-dominated EMI shielding at reduced thickness, relying on destructive interference of EMWs enabled by the asymmetric dual-nano conductive network, is thoroughly elucidated. Additionally, the composite exhibits superior IR stealth and self-extinguishing properties. This work offers a feasible strategy for designing high-performance stealth materials with strong potential for personnel and communication equipment protection.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0034
Catalytic cracking of gasoline and diesel to light olefins is a pivotal route for high-value utilization of surplus fuels, typically employing zeolite catalysts. This study systematically investigates the effects of zeolite type and acidic properties on the catalytic cracking of dodecane, a diesel model compound, using SAPO-34, ZSM-5 with SiO2/Al2O3 ratios of 38, 85, and 200, and USY. Catalysts were characterized by XRD, SEM, N2 physisorption, NH3-TPD, and pyridine-FTIR, and evaluated in a fixed-bed reactor. Results demonstrate that zeolite type is the primary determinant of conversion and product distribution. SAPO-34, with 0.38 nm pores, achieved only 24.33% conversion and negligible BTX yield, with severe external coking. ZSM-5-38 and USY, with larger pores, achieved near-complete conversion; however, ZSM-5-38, possessing moderate acidity, yielded the highest light olefins (18.40%) and minimal coke (0.18%), while USY, with higher acidity, promoted hydrogen transfer and coking (12.90% coke). Within ZSM-5 series, lower acid site density (ZSM-5-200) proved optimal, achieving 97.79% conversion and a total light olefin yield of 41.93% (ethylene 11.11%, propylene 20.33%, butenes 10.49%) with low coke (0.43%). The study proposes reaction pathways and regulatory mechanisms, highlighting that zeolite type and acidity govern the relative rates of cracking, hydrogen transfer, oligomerization, aromatization, and coking, thereby dictating performance. These findings provide a rational basis for optimizing zeolite catalysts in commercial gasoline/diesel cracking processes.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026022502
This study investigates the effects of different land use types on topsoil carbon (C) and nitrogen (N) contents and their spatial distribution in the lower reaches of the Sancha River Basin, a karst region of the Yunnan-Guizhou Plateau. Grid sampling collected 0–20 cm topsoil from forestland (n=23), cultivated land (n=25), and grassland (n=32). Total C and N were measured. Results showed that topsoil C content followed grassland (40.36±22.92 g·kg−1) > forestland (37.05±12.83 g·kg−1) > cultivated land (34.06±14.57 g·kg−1), while N content followed forestland (2.89±0.76 g·kg−1) > grassland (2.67±1.19 g·kg−1) > cultivated land (2.50±0.65 g·kg−1). One-way ANOVA revealed no significant differences among land use types (P>0.05). Soil C and N were significantly positively correlated across all land uses (r>0.5, P<0.001). Coefficient of variation (CV) indicated grassland had the highest C variability (0.57), while forestland showed the most stable C and N (CV=0.35 and 0.26, respectively). Cultivated land had CVs of 0.43 for C and 0.26 for N. Spatially, forestland exhibited concentrated high C values with significant N heterogeneity; grassland had higher C in southern and eastern areas but scattered distribution, with generally low and variable N; cultivated land showed uniform but lowest C and N. Land use types significantly drive topsoil C and N dynamics through vegetation input, soil disturbance, and management practices, underscoring the importance of rational land use planning for enhancing carbon sink functions and sustainable development in karst watersheds.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607023
The rapid population growth and accelerating urban development have made the comprehensive utilization of municipal sludge (MS) an urgent challenge. MS contains substantial organic matter and essential nutrients for crop growth, making it a promising soil amendment for the ecological restoration of mine waste rock. However, research evaluating the impact of MS application on soil health and ecological safety from a soil microbiology perspective remains understudied. Therefore, this study investigated the effects of MS and composted municipal sludge (CMS) on the ecological restoration of mine waste rock soil through pot experiments. High-throughput sequencing technology was employed to analyze changes in soil microbial community structure and diversity. Finally, network analysis and correlation heatmaps were utilized to elucidate the microbial driving mechanisms. The results indicated that after MS and CMS application, organic matter content increased from 20.38 g/kg (Level 3) to 38.52 g/kg (Level 2). The levels of available nitrogen, phosphorus, and potassium rose from Level 4, 6, 2, to Level 1, 4, 1, respectively. Fresh weight, aboveground height, root length, and stem diameter of ryegrass all increased significantly. Venn diagram and heatmap analyses indicated that lower application rates (<1.5 kg/m²) enhanced microbial community richness and diversity. This study confirms municipal sludge as an effective amendment for mine waste rock soil. It is recommended to limit application rates below 1.5 kg/m² in practical mine ecological restoration projects, with particular attention to long-term dynamics of heavy metals and salinity to ensure safe and sustainable land reuse.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3984-5
Rechargeable aluminum batteries (RABs) are promising for large-scale energy storage due to high theoretical capacity, inherent safety, and abundant aluminum reserves. However, conventional AlCl3-based ionic liquid electrolytes suffer from high cost, uncontrolled dendrite growth, and severe anode corrosion. Here, a molecular-level ligand engineering strategy is proposed, employing nitrogen-containing cyclic amides with tunable N–H functionalities to modulate the coordination environment of deep eutectic electrolytes (DEEs). Combined experimental and theoretical investigations reveal that the α-pyrrolidone-based DEE (PDEE) possesses a wider electrochemical window, higher ionic conductivity, and lower polarization. Precise N–H regulation optimizes cationic ligand and chloroaluminate anion interactions, accelerating ion transport to facilitate uniform Al deposition without dendrites. The amine functionalities enable in situ construction of a uniform inorganic-organic bilayer solid electrolyte interphase, mitigating anode corrosion and enhancing long-term interfacial stability. As a result, Al//Al symmetric batteries with PDEE achieve stable cycling for over 2000 hours, while Al-graphite full batteries demonstrate negligible capacity decay after 6000 cycles. This study establishes that ligand molecular engineering offers an effective strategy for optimizing DEEs, enabling durable and high-performance RABs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3921-2
Moisture-enabled energy harvesting technologies offer a promising route for self-powered strain sensing, yet conventional generators suffer from slow response, poor recovery, and limited multidirectional resolution. Here, we report a stretchable thermoplastic polyurethane (TPU) nanofiber moisture-enabled electric generator (MEG) with highly aligned ion channels. A carbon black/sodium dodecylbenzene sulfonate (CB/SDBS) layer is coated on the TPU membrane, while carboxymethyl cellulose (CMC) and acidified poly(sodium 4-styrenesulfonate) (HPSS) are applied on opposite sides, establishing lateral hydrophilicity and ion gradients to drive directional ion migration. The planar MEG is lightweight, flexible, and requires no fully covered electrodes, enabling conformity to complex deformations. The aligned channels reduce ion migration tortuosity, enhancing ion transport efficiency and flux. As a result, the aligned MEG (ATMEG) delivers 0.2 V and 0.51 μA cm−2 at ~90% relative humidity, corresponding to 400% and 287% enhancements compared with the unaligned MEG (UATMEG). The ATMEG also exhibits ultrafast response (0.16 s) and recovery (0.08 s). Utilizing its anisotropic characteristics, a multidirectional self-powered strain sensor is developed, capable of distinguishing both the amplitude and direction of human motion, demonstrating strong potential for adaptive wearable electronics and intelligent motion monitoring.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3915-8
Reactive oxygen species (ROS)-based antibiofilm therapy is limited by short ROS lifetime, restricted diffusion, and biofilm barriers. We designed a bacteria-targeted piezoelectric heterostructure (U-B/F) comprising boronic acid-functionalized UiO-66(Hf) (U-B) and carboxylated fullerene (C70-COOH). Boronic acid groups enable selective bacterial binding. Under ultrasound (US), the Z-scheme heterojunction enhances piezoelectric response and charge separation, amplifying sonocatalytic ROS generation. Fullerene acts as a peroxidase mimic, converting endogenous H2O2 into cytotoxic hydroxyl radicals (•OH). Additionally, favorable band alignment allows US-induced electron transfer from bacteria to U-B/F, disrupting bacterial electron transport and energy metabolism. Transcriptomic profiling confirmed bioenergetic collapse and oxidative stress. In vitro, U-B/F achieved 99.99% elimination of planktonic methicillin-resistant Staphylococcus aureus (MRSA) and 92.41% removal of mature biofilms. In MRSA-infected diabetic mice, U-B/F under US irradiation accelerated wound healing by eradicating infection, alleviating inflammation, and promoting tissue regeneration. This work provides a rational strategy for designing multifunctional nanomaterials integrating bacterial targeting, dual ROS catalysis, and electron transfer interference to combat biofilm-associated infections.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510071
Carbon source is a critical factor driving heterotrophic denitrification, yet the low carbon-to-nitrogen ratio (C/N) of livestock wastewater limits this process. This study developed novel composite carbon sources by combining corncob (CC) and polycaprolactone (PCL). Static carbon release and denitrification experiments were conducted to evaluate carbon release patterns and nitrogen removal performance. Results showed that the carbon release index (n) was below 0.45, indicating Fickian diffusion as the dominant release mechanism. The composite carbon source prepared at a CC:PCL mass ratio of 3:2 (denoted YP4) achieved a nitrate nitrogen removal efficiency of 94.76%, with effluent ammonia nitrogen meeting the discharge limits of GB 18596-2001. High-throughput sequencing revealed that YP4 increased the relative abundance of genera capable of denitrification and biopolymer degradation (e.g., Aeromonas, Novosphingobium, Bacteroides, and Clostridium sensu stricto), thereby enhancing heterotrophic denitrification and nitrogen removal. These findings provide a novel approach for selecting and preparing external carbon sources for biological heterotrophic denitrification of low C/N wastewater.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512066
This study addresses the removal of ammonia nitrogen (NH4+-N) and chemical oxygen demand (COD) from real coal chemical wastewater via electrochemical chlorine evolution. A nanorod-structured ruthenium dioxide catalyst (N-RuO2) was synthesized by modifying ruthenium trichloride precursor with ammonium chloride. Compared with unmodified RuO2, commercial DSA, and commercial RuO2 (Com-RuO2), N-RuO2 exhibited significantly enhanced electrochemical performance: Faradaic efficiency for chlorine evolution increased by 12.9%, 18.5%, and 25.6%, respectively; accelerated lifetime improved by 1.7, 1.9, and 2.9 times, respectively. In treating real coal chemical wastewater, N-RuO2 reduced NH4+-N to 86.4 mg·L−1 and COD to 72 mg·L−1, with degradation rate constants approximately 2.08 and 1.46 times higher than Com-RuO2, while energy consumption decreased by 17.7 Wh·g−1 and 1.5 Wh·g−1, respectively. Further studies showed that increasing chloride ion concentration enhanced removal rates and reduced energy consumption; higher current density accelerated removal but increased energy use; alkaline conditions favored NH4+-N removal, while neutral conditions favored COD removal. The excellent electrochemical performance of RuO2 nanorods indicates broad application prospects in practical water treatment.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60657-3
Fe-Mn catalysts have attracted considerable attention for industrial Fischer-Tropsch synthesis (FTS) due to their ability to modulate product spectra. Carbon adsorption and permeation on catalyst surfaces are critical elementary steps in the in situ formation of active iron carbide phases. Here, density functional theory (DFT) calculations systematically investigate the atomistic structures, thermodynamic stabilities, and electronic properties of carbon-deposited Fe-Mn alloy surfaces at the early stage of carburization. These surfaces exhibit distinct thermodynamic sensitivity to carbon atoms adsorbed on the surface and permeating into interstitial sites. By combining DFT with minima-hopping structural searches, we demonstrate that the initial stage of carbon permeation cannot trigger surface reconstruction to form iron carbide phases. The addition of manganese thermodynamically hinders carbon permeation. Although deposited carbon atoms modulate the electronic structure of metals, manganese retards the shift of d-band centers toward those of bulk iron carbide phases. This study provides atomic-scale insight into the in situ evolution of Fe-Mn catalyst surfaces during carbon deposition, indicating that manganese promoter has a noticeable effect on carbon permeation.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60672-X
Dry reforming of methane (DRM) converts CH4 and CO2 into syngas, offering a route to mitigate greenhouse gases. Ni-based catalysts suffer from sintering and carbon deposition at high temperatures. This work employs MgO-MgAl2O4 composite supports to regulate Ni loading and introduces Ce, La, and Zr as promoters to investigate their effects on DRM activity, structural stability, and surface oxygen species. Optimal Ni loading of 12.5% yields highest CH4 and CO2 conversions. Promoter introduction slightly suppresses low-temperature activity but substantially modifies support local structure and metal-support interface, improving NiO dispersion and increasing surface oxygen vacancies and active oxygen species (Oβ). These changes enhance CO2 adsorption-activation and suppress carbon deposition. After 20 h DRM, Ce-promoted catalyst shows smallest Ni particle growth (6.23→8.07 nm) and lowest carbon deposition, demonstrating superior stability and anti-coking capability. The study elucidates how Ce, La, and Zr enhance sintering and coking resistance via interfacial electronic modulation and improved oxygen storage/release, guiding rational design of stable Ni-based DRM catalysts.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60762-1
The CO2 dry reforming of methane (DRM) is pivotal for CO2 utilization within the dual-carbon framework, offering advantages in carbon reduction and value-added chemical production. However, shaped catalysts suitable for industrial-scale DRM remain limited. This work constructs a monolithic catalyst using honeycomb cordierite as the structural support, systematically investigating the effects of organic and inorganic binders on coating structure and catalytic performance. Comparative studies reveal that the active coating fabricated with inorganic aluminum sol exhibits a continuous uniform morphology and excellent adhesion strength. During high-temperature calcination, elemental diffusion within Al2O3 networks bridges the cordierite surface with active catalyst particles, forming a (Ni-Mg)AlxO4 composite structure. This creates robust metal-support interactions between active sites and the residual alumina matrix. The interconnected mesoporous framework provides superior pore confinement, contributing to strong coating adhesion, enhanced activity, and improved resistance to carbon deposition in the monolithic m-NCM-Al-sol catalyst. In contrast, coatings derived from inorganic silica sol suffer from detachment and activity loss due to heterogeneous surface structures and poor adhesion. Organic binders demonstrate inferior performance in macroscopic coating uniformity, adhesion strength, mesoporous confinement, and localized electronic effects, resulting in the poorest catalytic performance. By optimizing aluminum sol coating parameters—binder content, active component dosage, and coating cycles—a synergistic balance between coating thickness and mass transfer is achieved. The optimized catalyst demonstrates excellent DRM performance, providing insights for constructing high-performance shaped catalysts with cordierite coatings.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026012605
Synthetic phenolic antioxidants (SPAs) are widely used, leading to environmental contamination and human exposure. However, studies on their effects on adipocyte differentiation and underlying mechanisms, particularly for emerging SPAs, are limited. This study evaluated the impacts of 4-tert-octylphenol (4-t-OP) and three novel antioxidants (AO 3114, AO 1135, AO 702) on adipogenesis using the mouse 3T3-L1 preadipocyte differentiation model. Lipid staining, triglyceride measurement, differentiation-related gene expression analysis, and transcriptomic approaches were employed. All four SPAs significantly promoted differentiation of 3T3-L1 cells into mature adipocytes and upregulated expression of peroxisome proliferator-activated receptor gamma (Pparγ) and mature adipocyte marker genes. Transcriptomic analysis revealed differential effects on gene transcription during early differentiation. GO and KEGG enrichment analyses indicated that these SPAs promoted adipogenesis by enhancing energy metabolism and protein synthesis, as well as regulating PPAR and other signaling pathways. In conclusion, the tested SPAs promote adipogenesis and disrupt lipid metabolism through distinct mechanisms, suggesting long-term exposure may cause metabolic disorder risks and pose a public health threat.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026031103
Sintering ash washing wastewater from steel plants is characterized by high salinity, high chloride content, high thallium load, and coexistence of multiple metals, posing significant treatment challenges. This study employed thermodynamic simulation to elucidate the speciation and transformation of thallium in such wastewater, and systematically investigated a combined process of sulfide precipitation coupled with coagulation-flocculation. The results showed that at pH 9–10, thallium predominantly existed as Tl+. Under oxidizing conditions, the stable complex anion [TlCl4]− dominated at pH < 8.1, while at pH > 8.1, a mixed system of solid Tl2O3 and dissolved TlClO3 coexisted. Under optimized conditions (pH 12, 2.0% thallium removal agent, 1.0% multi-effect auxiliary agent), the thallium concentration in the wastewater decreased from an initial 9.58 mg·L−1 to 4.31 μg·L−1, meeting the stringent discharge limit of ≤5 μg·L−1. Concurrent removal of Cu, Zn, and Cd was achieved. The primary removal mechanism was sulfide precipitation, with lattice substitution between Tl+ and K+ serving as an auxiliary pathway. This study provides a practicable technical route for advanced treatment of high-chloride, high-thallium industrial wastewater.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608006
Organic waste is a potential phosphorus reservoir, and understanding the dynamics of available phosphorus (AP) during its resource utilization is critical for efficient phosphorus recovery. Composting, a key route for organic waste valorization, involves complex transformations of phosphorus alongside organic matter degradation and humification. However, the long duration and high cost of composting experiments, coupled with multifactorial influences, hinder efficient elucidation of AP dynamics via conventional methods. This study compiled data from 33 publications, constructing a dataset of 647 samples. Data preprocessing included iterative imputation, one-hot encoding, and standardization. A stacking ensemble learning model was developed to predict AP generation during composting. The optimal ensemble comprised XGBoost and SVR as base learners and ElasticNet as the meta-learner, achieving R² values of 0.954 and 0.928 on training and test sets, respectively, with low overall error. SHAP analysis revealed that key factors influencing AP content, in descending order of importance, were feedstock type, bulking agent type, turning interval, pH, electrical conductivity (EC), and C/N ratio. Notably, livestock manure as feedstock and straw-based bulking agents contributed positively to AP predictions. Partial dependence plots indicated that lower pH and C/N ratios generally favored AP accumulation throughout composting. During the initial stage, higher moisture content and lower EC enhanced AP; in the thermophilic phase, higher temperatures corresponded to higher AP; and during cooling and maturation, maintaining moisture below 48% and C/N below 14, while extending composting beyond 43 days, promoted AP accumulation. This study demonstrates accurate AP prediction via stacking ensemble learning and identifies critical factors, offering support for optimizing phosphorus management in composting engineering.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608018
Chlorinated volatile organic compounds (CVOCs) are volatile, difficult to degrade, and highly toxic, posing serious threats to the atmospheric environment and human health. Catalytic oxidation is currently one of the mainstream methods for CVOCs abatement, owing to its high efficiency, safety, and economic feasibility, and its key aspect lies in the design and development of high-performance catalysts. In the catalytic oxidation of CVOCs, the poisoning effect of chlorine species on catalysts severely restricts catalytic performance. Ru-based catalysts, which exhibit excellent catalytic oxidation activity toward CVOCs and favorable chlorine-resistant performance, have been widely studied in recent years. This paper reviews the latest research progress on Ru-based catalysts for the catalytic oxidation of CVOCs. The mechanism of catalytic oxidation of CVOCs by Ru-based catalysts is elucidated through a systematic analysis of the relevant literature. Furthermore, the strategies for the design and structural regulation of Ru-based catalysts are outlined from the perspectives of active components, supports, and surface modification. Finally, novel preparation methods for Ru-based catalysts and the influence of reaction components on catalytic performance are summarized. Future research directions in this field are also prospected, aiming to provide a reference for the subsequent design and development of high-performance Ru-based catalysts suitable for complex operating conditions.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4084-1
Alkali metal halides such as KCl are typical insulators with broad bandgaps, exhibiting poor luminescence. Ion doping can enhance their luminescence, but the mechanism of ultrafast diffusion and structural evolution remains unclear. Here, Sb3+ was doped into a KCl matrix via a room-temperature grinding route. Varying Sb3+ concentration induces a structural evolution from KCl:Sb3+ to 0D inorganic metal halides (IMHs) K3SbCl6. The resulting K3SbCl6 exhibits broad-spectrum yellow emission with near-unity photoluminescence quantum yield (PLQY). The luminescence mechanism is attributed to the 3P1→1S0 transition of Sb3+ ions. Furthermore, a room-temperature solid-liquid interface diffusion method enables ultrafast single-crystal growth of K3SbCl6 in only 20 seconds, with stable luminescence. The material demonstrates excellent temperature sensing performance in the 50–310 K range, achieving a maximum relative sensitivity of 9.99%/K. Additionally, K3SbCl6 shows application potential in information encryption, flexible composite fluorescent films, and white light-emitting diodes. This study provides new insights into ultrafast synthesis of high-performance luminescent materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4036-4
Alkaline water electrolysis is a pivotal technology for large-scale green hydrogen production, yet its efficiency is constrained by sluggish hydrogen evolution reaction (HER) kinetics at industrial current densities. Here, we propose a synergistic dual-doping strategy to lower kinetic barriers for both Volmer and Heyrovsky steps. A robust amorphous NiCoV nanosheet electrode was synthesized via scalable one-step electrodeposition. In situ spectroscopic and kinetic characterizations reveal that hydrophilic V species optimize interfacial water by disrupting the hydrogen bond network, ensuring rapid supply of free water at the inner Helmholtz plane. Co dopants modulate electronic structure to facilitate electron transfer and optimize intermediate adsorption energetics. The NiCoV electrode requires an ultralow overpotential of 253 mV at -400 mA cm−2, surpassing most Pt-based catalysts, and maintains stability for over 200 h. Industrial validation in a scaled-up electrolyzer demonstrates a cell voltage of 1.89 V at 400 mA cm−2, achieving energy savings of 0.12 kWh m−3 H2 compared to commercial benchmarks. This translates to annual electricity savings of 1.33 × 10^6 kWh for a medium-scale demonstration project, highlighting immense potential for sustainable industrial applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4030-y
In the era of artificial intelligence, efficient perception and processing of massive visual information demand advanced machine vision systems. Inspired by human visual adaptation, various optoelectronic devices have been developed, yet most rely on external gate voltages or complex circuits for dynamic sensitivity modulation. This work demonstrates an all-optically controlled biomimetic sensor based on a one-dimensional ZnO/MAPbBr3 heterojunction, achieving both positive and negative photoconductivity effects. By modulating oxygen vacancy states with ultraviolet light, the competition between intrinsic photoconduction and trap-mediated carrier capture is regulated, enabling dynamic control of visible-light photoresponse within a single device. This tunable behavior mimics scotopic adaptation (photopigment regeneration under weak illumination), photopic adaptation (photopigment bleaching in bright environments), and eyelid-like self-protection against intense light. The device operates without external gate bias or cascaded circuits, offering a promising strategy for next-generation intelligent biomimetic sensors in machine vision.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4052-0
Cutaneous wound infections affect millions of patients annually worldwide, and early diagnosis is critical for timely anti-infection treatment. Bacterial infections alter wound pH, offering a promising diagnostic approach. Here, a diagnostic smart dressing (CMC-PDBI) is developed by ultraviolet-initiated crosslinking of a pH-responsive indicator coating, incorporating modified bromothymol blue, onto a carboxymethyl cellulose substrate. The dressing exhibits superior pH-triggered color-changing performance in both phosphate buffer solution and bacterial cultures across the pH range associated with wound infection (orange at pH 6.0, green from pH 6.5 to 7.5, blue at pH 8.0). In a murine wound infection model, CMC-PDBI indicates infection two days before symptomatic manifestation. Early therapy guided by the dressing accelerates wound healing and reduces inflammation. A smartphone application (InfectSense) assists in identifying infection risk. This work presents a novel early-warning platform for qualitative visual diagnosis of wound infections before clinical symptom onset, with high potential for clinical and home care settings.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4074-6
Achieving carbon neutralization relies heavily on green hydrogen and electrochemical carbon-nitrogen cycles. However, the complexity of these systems and the cost of traditional Edisonian trial-and-error methods hinder rapid progress. Artificial intelligence (AI) has emerged as a transformative tool, enabling high-throughput data processing and dynamic adaptation. This review surveys the landscape of AI-driven electrochemistry, bridging the gap from atomic-scale design to industrial-scale implementation. Specifically, we focus on three areas: atomic structure-function decoding, fully automated “self-driving” laboratories, and macro-scale simulations for device durability. Furthermore, we elucidate the critical challenges in integrating AI with materials science. By mapping current trends and future directions, this work aims to unlock the full transformative potential of AI in next-generation energy storage and conversion.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60686-X
This study reports a streamlined route for synthesizing plate-like α-Al2O3 via co-combustion activation of coal gangue and corn stalk, enabling high-value utilization of solid wastes. The introduction of corn stalk significantly reduces the apparent activation energy of coal gangue combustion and increases the acid leaching yield of aluminum to 81.9%. Mechanism analysis reveals that titanium and iron ions in the co-combustion ash leachate act as natural morphology regulators, facilitating the formation of a plate-like structure in the alumina product, with titanium exhibiting leaching behavior consistent with that of aluminum. Furthermore, a high content of AlO6 structural units in the precursor effectively promotes the direct conversion into dense α-Al2O3 crystals during thermal treatment, thereby enhancing product density. Under optimized conditions (800 °C, 1 h), the as-prepared α-Al2O3 exhibits a plate-like morphology, with a median particle size (d50) of 5.70 μm and a density of 4.94 g/cm3. This work provides a new approach for the synergistic resource utilization of coal gangue and biomass waste.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4132-y
Manganese-iron-based mixed polyanionic cathodes are promising for sodium-ion batteries (SIBs) due to high energy density and operating voltage, but suffer from Jahn-Teller distortion of Mn3+ that degrades cycling stability. Here, a structural modulation strategy via Mg2+ doping is reported. Electrochemically inert Mg2+ forms stronger chemical bonds, adjusts lattice parameters, and suppresses Jahn-Teller distortion, enhancing structural stability. Mg2+ also widens sodium-ion diffusion channels, improving diffusion kinetics. Additionally, an in-situ three-dimensional carbon nanotube (CNT) conductive network boosts electronic conductivity. The resulting NFMPP-Mg@CNTs cathode delivers a discharge capacity of 126 mAh g−1 at 0.1 C (near theoretical 129 mAh g−1), retains 80% capacity after 3000 cycles at 0.5 C, and achieves an energy density of 401 Wh kg−1, among the highest reported for mixed phosphate systems. Ex-situ XPS and first-principles calculations confirm that Mg2+ resists geometric distortion by enhancing lattice stability and widening Na+ diffusion pathways (migration barrier reduced from 0.566 to 0.398 eV). This work provides a viable route for high-energy, long-life SIB cathodes suitable for large-scale energy storage.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4150-2
Bacterial infection and irregular wound morphology are major challenges in clinical wound management. Injectable hydrogels can conform to irregular wound geometries but often lack antimicrobial activity. Here, we report an injectable hydrogel (HPAu gel) formed by sequentially mixing phenylboronic acid-modified hyaluronic acid (HA-PBA) and chloroauric acid under alkaline conditions. The gel's internal multiple crosslinks enable uniform encapsulation of in situ-generated gold nanoparticles. Hydrogen bonds and phenylboronic acid ester bonds confer self-healing, injectability, and adhesion, allowing effective sealing of irregular cavities. In vitro, the hydrogel exhibits long-lasting photothermal stability and eliminates multiple bacterial strains. In a mouse dorsal full-thickness infected wound model, HPAu gel under near-infrared (NIR) irradiation eradicated Staphylococcus aureus, reduced inflammation (TNF-α fluorescence area significantly lower; IL-10 area 12.88‰ vs <2‰ in Blank), promoted vascular regeneration (CD31 and α-SMA expression increased), and accelerated wound healing. This work presents a promising strategy for treating irregular infected wounds.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3460-4
Atomically dispersed single-atom catalysts (SACs) on graphene offer a tunable platform for electrochemical CO2 reduction to CH4, yet the mechanistic coupling between active-site identity and coordination environment remains poorly resolved. This study constructs a structure-activity map for 110 stable SACs with MXnY4−n motifs (X, Y = N, S, P; M = 19 transition metals) using density functional theory and multi-task symbolic regression. The binding strength of the *OCHO intermediate (ΔE*OCHO) is identified as the initial activity descriptor, correlating with the onset potential for CH4. A three-dimensional descriptor comprising valence-electron number and electronegativity of metal and coordinating atoms reproduces ΔE*OCHO and onset potential variations without further DFT calculations. The analysis reveals that coordination environments modulate the d-band center and charge transfer, shifting the rate-determining step from CO2 activation to *CO hydrogenation. This descriptor enables rapid screening of SACs, bypassing computationally expensive DFT workflows. The findings provide a rational basis for designing graphene-supported SACs with enhanced CH4 selectivity and establish a generalizable framework for decoupling active-site and coordination effects in CO2 electrocatalysis.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3327-8
Biodegradable zinc (Zn) alloys have emerged as viable candidates for medium- to high-load-bearing implants, outperforming magnesium alloys in strength and ductility while exhibiting in vivo degradation rates that align with vascular (3–6 months) and bone (2–3 months) healing. Clinical translation has advanced to maxillofacial fixation, interference screws, and drug-eluting coronary stents. Alloy design has evolved from Zn-Mg and Zn-Li systems to Zn-Mn alloys that achieve 143% room-temperature elongation via surface-roughness-induced plasticity. Conventional strengthening relies on grain refinement, yet fine-grained Zn alloys suffer reduced creep resistance at body temperature (0.45 homologous temperature). A paradigm shift was introduced by Nie’s group: coarse-grained Zn-0.2Mg (47 μm) exhibits higher yield strength than fine-grained (11 μm) counterparts, defying the Hall-Petch relationship. This anomaly arises from accommodation twinning that maintains intergranular cohesion, shifting deformation from intergranular to intragranular mechanisms. Multi-component alloys (Zn-0.2Mg-0.1Cu-0.2Mn) achieve compressive yield strengths exceeding 400 MPa with grain sizes of 10–50 μm, alongside improved creep resistance and acceptable cytotoxicity relative to Mg-Zn-Ca. A 6-week in vivo study confirmed appropriate degradation. These findings establish grain coarsening as a counterintuitive but effective pathway for designing stronger, more durable biodegradable Zn alloys for load-bearing applications.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3546-5
Organic cocrystals have emerged as a distinct functional material platform for near-infrared (NIR) optoelectronics, exploiting charge-transfer (CT) interactions between donor and acceptor constituents to generate ultranarrow optical bandgaps. This review systematically consolidates design strategies, controlled synthesis routes, structure–property relationships, characterization methodologies, and frontier applications of NIR-active organic cocrystals. The central mechanistic premise is that hybridization of the donor HOMO and acceptor LUMO produces new excited states whose absorption or emission extends into the 780–2500 nm window. Unlike conventional inorganic NIR materials, which incur high cost and complex fabrication, or discrete organic small molecules, which require multistep synthesis, cocrystals offer a non-destructive assembly route with tunable photophysical output, improved biocompatibility, and environmental stability. The review surveys cocrystal systems including TCNQ- and TCNB-based architectures, carbazole-based CT complexes, and TTF-derived conductors, with emphasis on how hydrogen- and halogen-bonding motifs govern packing, ionicity, and optoelectronic response. Controlled synthesis methods—mechanochemical grinding, vapor digestion, and solution assembly—are compared with respect to polymorph selectivity and stoichiometric fidelity. Characterization approaches spanning three-dimensional electron diffraction, FT-IR, and single-crystal X-ray analysis are evaluated for their capacity to resolve CT degree and band structure. Applications in NIR photothermal conversion, organic field-effect transistors, optical waveguides, and amplified spontaneous emission are assessed against performance metrics. Remaining challenges include scalable polymorph control, quantitative prediction of CT degree, and long-term operational stability under ambient and biological conditions.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3540-y
Polymeric multicolor afterglow materials with tunable phosphorescence and environmental adaptability remain a bottleneck in optical anti-counterfeiting. This work integrates triplet-to-singlet Förster resonance energy transfer (TS-FRET) with ultraviolet (UV) laser direct writing to fabricate phosphorescent anti-counterfeiting labels. Using poly(acrylamide-co-4'-vinyl-[1,1'-biphenyl]-3,5-dicarboxylic acid) (BCA2PAM) as the donor and rhodamine 6G (R6G) as the acceptor, precise color tuning is achieved. Time-resolved multicolor displays are realized by loading afterglow materials onto filter paper, while luminescent elastomers are synthesized via integration with polydimethylsiloxane (PDMS). Laser inscription of 'disappear' on R6G-doped BCA2PAM films at varying laser powers yields exclusive visibility of 'appear' under UV irradiation; upon UV off, 'disappear' emerges, followed by reappearance of 'appear' after 1 s, demonstrating encryption efficacy. High-power laser-inscribed QR codes remain imperceptible under UV but become visible after simulated breath exposure and subsequent UV activation. Integrated with polyethylene terephthalate (PET) adhesive tapes, the films form tamper-evident labels with customizable branding. Laser-written patterns visible under UV can be erased under ambient humidity and re-encrypted with new motifs, exhibiting rewritable capability. These results provide a new method based on ultraviolet light and multicolor time-resolved coupling in optical encryption, demonstrating industrial production potential for high-end anti-counterfeiting labels.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3643-8
Inverted perovskite solar cells (PSCs) suffer from defect-mediated nonradiative recombination and inefficient charge extraction, particularly at the buried interface and grain boundaries (GBs), which limit power conversion efficiency (PCE) and operational stability. This study introduces a multifunctional phosphonic acid molecule, (2-(3,6-bis(trifluoromethoxy)-9H-carbazol-9-yl)ethyl)phosphonic acid (M28), as an additive in the perovskite precursor solution. M28 spontaneously segregates toward the buried interface and GBs, fulfilling three roles: (1) slowing crystallization to enlarge grains and improve film quality, (2) passivating defects to suppress charge recombination, and (3) inducing p-type doping to create an extra electric field that promotes hole transport. Devices incorporating M28 achieve a champion PCE of 25.96% and retain 80% of initial efficiency after 1500 h of maximum power point tracking. This work demonstrates the efficacy of multifunctional phosphonic acid additives in addressing buried-interface and GB defects, offering a viable route to high-performance, stable inverted PSCs.