SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4312-8
Carbazole phosphonic acid-based self-assembled molecules (SAMs) serve as effective hole-selective contacts in organic solar cells (OSCs), yet their molecular packing and aggregation behavior during solution processing remain difficult to control, limiting hole transport and device durability. This study introduces a polymer-templated self-assembly strategy to regulate molecular organization by one-step spin-coating a blend of [2-(9H-carbazol-9-yl)ethyl]phosphonic acid (2PACz) and PEDOT:PSS. The polycationic PEDOT+ framework acts as a template, providing supplementary anchoring interactions that promote ordered molecular arrangement and suppress unfavorable agglomeration. Pronounced face-on orientation and enhanced structural coherence of 2PACz within the polymer matrix are evidenced. The templated ordering improves vertical charge transport, interfacial homogeneity, and film morphology. In binary OSCs based on PM6:BTP-eC9, the hybrid hole transport layers (HTLs) yield a champion power conversion efficiency (PCE) of 20.26%, with an open-circuit voltage (VOC) of 0.874 V, a short-circuit current (JSC) of 28.97 mA cm-2, and a fill factor (FF) of 80.02%. Devices incorporating hybrid HTLs exhibit exceptional operational stability, retaining over 90% of initial PCE (T90) after 405 h of continuous operation at the maximum power point (MPP). This work establishes polymer-directed SAM assembly as a scalable route to simultaneously optimize nanoscale molecular packing, interfacial energetics, and long-term device stability for high-performance OSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4433-5
Negative thermal expansion (NTE) and zero thermal expansion (ZTE) materials are technologically relevant for precision engineering, yet their practical deployment is constrained by narrow operating temperature windows. This study introduces an entropy-designing strategy to regulate the thermal expansion behavior in the AⅠBⅡCⅢMo3O12 system, specifically K0.4(Mg0.25Mn0.25Co0.25Ni0.25)0.4Sc1.6Mo3O12 (CE0.4MO) and related CExMO compositions (x = 0.4, 0.6, 0.8, 1.0). By tuning configurational entropy, the operating temperature windows for both NTE and ZTE are significantly broadened, with the ZTE region shifting to higher temperatures. Among single-phase compositions, CE0.4MO exhibits the lowest configurational entropy and demonstrates NTE from 100 to 830 K and ZTE up to 1100 K, surpassing most reported ZTE materials. Systematic analyses of structural evolution, lattice dynamics, and electronic structure reveal that reduced configurational entropy suppresses structural evolution, directly correlating with decreased structural flexibility. Higher atomic displacement parameters (ADPs) of oxygen in CE1.0MO provide experimental evidence for enhanced flexibility. Raman spectroscopy shows that the full width at half maximum (FWHM) of peaks in the 750–900 cm-1 range positively correlates with configurational entropy, indicating reduced lattice disorder, while modes within 750–1050 cm-1 blue-shift as entropy decreases, confirming lattice stiffening. Electron localization function (ELF) and charge density analyses indicate that Mg/Mn/Co/Ni/Sc–O bonds are ionic, with ionicity weakening as configurational entropy decreases, thereby enhancing constraints on atomic vibrations and reducing structural flexibility. This work establishes a theoretical foundation for designing thermal expansion materials with wide operating temperature ranges.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4479-8
The von Neumann architecture is increasingly constrained by energy consumption and data-transfer efficiency as artificial intelligence and data-intensive applications expand. Neuromorphic computing, inspired by the human brain's information-processing mechanisms, offers an alternative paradigm. Two-dimensional (2D) ferroelectric materials are promising candidates due to their intrinsic non-volatility, atomic-scale thickness, ultra-low power consumption, excellent fatigue endurance, and dangling-bond-free surfaces. This review examines recent advances in 2D ferroelectric materials and associated device architectures for neuromorphic applications. It first introduces ferroelectric mechanisms and representative 2D ferroelectrics, then surveys key device architectures including ferroelectric tunnel junctions, diodes, transistors, and photovoltaic devices. Their applications in in-memory computing and in-sensor neuromorphic systems are discussed, with emphasis on artificial neural networks, spiking neural networks, reservoir computing, and neuromorphic perception for efficient information processing and intelligent sensing. The unique properties of 2D ferroelectrics enable integrated sensing, memory, and computing functionalities, demonstrating potential for future neuromorphic and brain-inspired intelligent systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4318-5
The development of high-entropy alloy (HEA) electrocatalysts for proton exchange membrane water electrolysis (PEMWE) is constrained by the thermodynamic instability of unconventional crystal phases and the trade-off between activity and durability under acidic oxygen evolution reaction (OER) conditions. This work demonstrates that crystal-phase engineering, using Au nanowires (NWs) as a crystallographic template, stabilizes a 4H-phase HEA core–shell nanostructure (4H-Au@4H-IrPtNiFeCo NWs) that is otherwise inaccessible via conventional synthesis. The 4H-phase HEA electrocatalyst achieves a current density of 3000 mA cm−2 at 1.90 V and maintains stable operation for over 1200 h at 1000 and 2000 mA cm−2 in a PEMWE device. These device-level metrics indicate that the advantage of the 4H-phase HEA extends beyond half-cell measurements, translating into improved PEMWE performance. The unique combination of unconventional atomic stacking, electronic modulation, multielement synergy, and enhanced thermal stability underpins the enhanced acidic water electrolysis performance. This study positions crystal phase, alongside composition, morphology, and surface structure, as a key design parameter for high-performance HEA catalysts in energy conversion and chemical transformation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4328-2
Laser-driven broadband near-infrared (NIR) light sources are highly desirable for diverse non-visible optical applications. However, conventional phosphor-in-silicone converters will be rapidly invalidated under high-power laser excitation, and the poor structural stability of Cr3+ activated gallate/germanate phosphors makes them prone to interfacial reaction with silicate glass, leading to substantial deterioration in luminescence properties of phosphor-in-glass film (PiGF) converters. Herein, we report an efficient and stable ultrabroadband NIR PiGF with a high internal quantum efficiency of ≈ 94%, a long peak wavelength of 850 nm and an ultra-large full width at half maximum of 300 nm. The detrimental interfacial reactions with glass matrix are effectively suppressed by embedding the Cr3+ activated superstoichiometric MgO·1.75Al2O3 phosphor, which is attributed to the superior high-temperature structural stability of the aluminate spinels. Through effective thermal management by the sapphire plate and further a motor-driven rotating wheel, a high-performance laser-driven light source is further demonstrated, which can deliver high-brightness ultrabroadband NIR light with an output power exceeding 1.1 W, a light conversion efficiency of 26%, and a stable operation for over 15 hours. Our work provides an efficient, stable and cost-effective all-inorganic converter for the development of laser-driven NIR light sources.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4447-3
Chargeable photoconductivity, a non-volatile photoresponse phenomenon, was investigated in multiferroic heterostructures comprising Bi0.85La0.15FeO3 (BLFO) and a quasi-two-dimensional electron gas (Q2DEG). Two device architectures, LSMO/BLFO/Q2DEG and Pt/BLFO/Q2DEG, were fabricated and characterized under varying electrical connection conditions between the top electrode and the Q2DEG during illumination and dark waiting stages. Current-voltage (I-V) measurements reveal that the heterostructures exhibit persistent photoconductivity after illumination, with the magnitude and retention dependent on the circuit configuration. Under open/open conditions, the photocurrent increases with illumination duration, and subsequent dark waiting leads to a gradual decay, indicating charge storage and release mechanisms. The LSMO/BLFO/Q2DEG heterostructure demonstrates superior chargeable photoconductivity compared to the Pt counterpart, attributed to the oxygen vacancy migration and interfacial polarization effects. These findings establish a foundation for oxide-based photoelectric memory devices with potential for low-power, non-volatile optoelectronic applications. The results provide critical insights into the interplay between ferroelectric polarization, oxygen vacancy dynamics, and charge trapping at the BLFO/Q2DEG interface, offering a pathway for designing advanced multiferroic optoelectronic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4309-8
Iridium-doped cobalt oxide nanosheets derived from a ZIF template were evaluated as oxygen evolution reaction (OER) catalysts for proton exchange membrane water electrolysis (PEMWE). Residual carbon was removed via a post-synthetic treatment to isolate intrinsic catalytic behavior. The Ir0.23Co0.77Ox catalyst exhibited enhanced activity and durability relative to commercial IrO2 in a practical PEMWE device. Potential-dependent, stage-resolved characterization combined with theoretical calculations probed catalyst stability under different operating voltages, revealing degradation mechanisms tied to applied potential. Contact angle measurements showed that the Ir0.23Co0.77Ox membrane electrode assembly (MEA) had water and air contact angles of 126° and 143°, respectively, compared to 126° and 143° for an IrO2 MEA at identical Ir loading, indicating improved wettability and gas release behavior. The work provides a framework for understanding potential-dependent stability in acidic OER catalysts and demonstrates a viable route to reduce Ir loading while maintaining PEMWE performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4468-6
The proliferation of multispectral detection platforms demands materials that simultaneously satisfy electromagnetic interference (EMI) shielding and infrared (IR) camouflage without compromising radio-frequency (RF) transmission. Conventional MXene films exhibit exceptional EMI shielding (>40 dB) but suffer from high IR emissivity and severe RF reflection, precluding integration with wave-transmitting arrays. This work introduces liquid metal (LM)-modified MXene composite films engineered via structural patterning to decouple optical, IR, and RF responses. The LM phase, dispersed within the MXene interlayer galleries, reduces free-electron density and tailors the dielectric loss, while a periodic array architecture creates impedance-matched windows for RF transmission. The resulting films achieve an EMI shielding effectiveness of 36 dB at 510 µm thickness, with a low IR emissivity of 0.36 and an RF transmittance exceeding 80% in the X-band. The patterning strategy suppresses surface current continuity, mitigating the trade-off between shielding and transmission. These metrics represent a 20% improvement in IR camouflage and a 15% enhancement in RF transparency relative to pristine MXene films. The composite films also demonstrate mechanical flexibility, retaining 95% of initial conductivity after 1,000 bending cycles. This work establishes a scalable route for multispectral-compatible materials critical for next-generation stealth and communication systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4263-3
Monolayer black phosphorus (phosphorene) exhibits a direct bandgap and strong in-plane anisotropy, making it a promising candidate for near-infrared (NIR) optoelectronic devices. However, the precise modulation of its excitonic emission via anisotropic strain remains insufficiently understood, particularly regarding the contrasting strain responses of phosphorene versus transition metal dichalcogenides (TMDs). Here, we combine experimental characterization with tight-binding (TB) modeling to elucidate the strain-dependent bandgap evolution in phosphorene. Using a four-band TB model, we derive the bandgap at the Γ point as E_g^BP = 4t1 + 2t2 + 4t3 + 2t5, with hopping parameters t1 = -1.220 eV, t2 = 3.665 eV, t3 = -0.205 eV, t4 = -0.105 eV, and t5 = -0.055 eV. Under tensile strain along the zigzag (ZZ) direction, the interatomic distance associated with t1 increases, reducing the magnitude of |t1|. Since t1 is negative, the bandgap increases, contrary to the behavior of monolayer MoS2, where tensile strain decreases the bandgap due to positive hopping parameters t11, t22, and t12. This anisotropic strain response enables selective tuning of NIR exciton emission. Our findings provide a quantitative framework for strain engineering in phosphorene-based NIR devices, highlighting the critical role of hopping parameter signs in determining bandgap modulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4177-3
Chirality profoundly influences tumor therapy by regulating key physiological processes, yet the link between chirality and therapeutic properties of atomically precise metal nanoclusters (NCs) remains poorly understood. Atomically precise Au25 NCs protected by chiral cysteine ligands (L-Au25(cys)18, D-Au25(cys)18, and Rac-Au25(cys)18) were constructed and systematically investigated to elucidate the association between chirality and tumor therapeutic performance. Although no significant difference in enzyme-like activity was observed among the three NCs, Rac-Au25(cys)18 exhibited enhanced reactive oxygen species generation under 808 nm laser irradiation, achieving superior phototherapeutic effects in both in vitro and in vivo tumor models. The chiral Au25 NCs induced distinct cell death pathways: L-Au25(cys)18 primarily triggered ferroptosis, D-Au25(cys)18 induced both ferroptosis and apoptosis, and all three NCs activated disulfidptosis. In vivo, tumor inhibition rates for L-Au25, D-Au25, and Rac-Au25 groups were 46.7%, 42.5%, and 68.3%, respectively, with no significant body weight fluctuations and minimal hepatorenal toxicity. Hematological and histopathological analyses confirmed favorable systemic biocompatibility. This work clarifies the correlation between chiral structures and tumor therapeutic performance of gold NCs, providing experimental insights and theoretical support for the design of novel chiral nanomaterials and optimization of precise tumor phototherapeutic strategies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4244-0
Near-infrared perovskite light-emitting diodes (NIR-PeLEDs) suffer from poor operational stability, largely due to interfacial reactions at the electron-transport layer (ETL)/perovskite interface. Here, we introduce a zinc ion (Zn2+)-chelated hybrid ETL derived from a Zn2+-chelated polyethylenimine ethoxylated (PEIE) complex, which partially retains the surface properties of ZnO but exhibits significantly reduced oxygen defects and surface-adsorbed hydroxyl groups. This well-modulated surface promotes perovskite crystallization and mitigates interface-induced deprotonation of organic cations during device operation. Consequently, NIR-PeLEDs employing this hybrid ETL achieve a peak external quantum efficiency (EQE) of 20.1%, a high radiance of 652 W sr-1 m-2, and an exceptional T50 lifetime of 270.7 hours at a high current density of 100 mA cm-2, which is over five times that of devices based on conventional ZnO nanocrystal (NC) ETLs. Our results present an effective ETL strategy for operationally stable NIR-PeLEDs and thoroughly reveal the critical role of regulating interfacial reactions in stabilizing buried interfacial contacts. These findings provide valuable insights for advancing perovskite optoelectronic devices that suffer from interface-induced performance degradation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4269-4
Self-assembled molecular interlayers (SAMs) are promising hole-selective contacts for high-efficiency organic solar cells (OSCs) due to their well-defined energy alignment and minimal parasitic absorption. However, their intrinsically limited mechanical robustness often leads to structural degradation and performance loss under mechanical deformation, restricting their application in flexible devices. Here, we report a nanoparticle-reinforced self-assembled composite interface that simultaneously enhances mechanical reliability and optoelectronic performance. Uniformly dispersed SiO2 nanoparticles are introduced as high-modulus reinforcing building blocks without disturbing molecular self-assembly. In contrast to NiOx nanoparticles, which suffer from aggregation and parasitic absorption, SiO2 nanoparticles exhibit excellent dispersion and optical transparency, enabling formation of a structurally compatible hybrid interface. Mechanistic studies reveal that SiO2 nanoparticles redistribute interfacial stress and form dynamic hydrogen-bond networks with phosphonic acid groups of 2PACz, providing efficient energy dissipation during cyclic deformation. Meanwhile, modulation of interfacial polarity extends the crystallization time window of the active layer, resulting in enhanced molecular ordering and improved charge transport. As a result, devices based on the SiO2/2PACz composite interface achieve a power conversion efficiency of 20.14% for rigid devices and 19.30% for flexible devices, placing the flexible devices among the highest-performing flexible OSCs reported to date, while retaining over 90% of their initial efficiency after repeated bending cycles. This work establishes a general strategy for overcoming the trade-off between electronic selectivity and mechanical robustness in ultrathin self-assembled molecular interfaces, providing design insights for high-performance flexible organic optoelectronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4342-3
Electron acceptors containing single-bond-linked building blocks offer attractive advantages for organic solar cells owing to their synthetic simplicity and structural modularity. However, achieving backbone planarity without compromising electronic compatibility remains a persistent challenge. Conventional conformational locking strategies based on alkoxy substitution can effectively suppress torsional freedom but often elevate the highest occupied molecular orbital energy level, limiting compatibility with widely used donor polymers. Here, we report a partially fused electron acceptor design that achieves intrinsic backbone planarity through heterocycle selection rather than side-chain-assisted conformational locking. By incorporating a benzodifuran core and furan-thiophene linkages, the resulting acceptors exhibit a near-coplanar backbone geometry as revealed by density functional theory calculations, without the need for electronically perturbing alkoxy groups. Devices based on the optimized acceptor (BDF-1) deliver a binary power conversion efficiency of 12.2%, and further improvement to 19.5% is achieved in a ternary blend with PM6 and BTP-eC9. The enhanced performance is accompanied by favorable morphology, balanced charge transport, and suppressed recombination losses. This work provides molecular-level insight into partially fused acceptor design and demonstrates that heteroatom-guided conformational locking offers a viable strategy for expanding the design space of acceptors with single-bond-linked building blocks while maintaining compatibility with mainstream donor systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4360-7
Polarization-sensitive photodetection is critical for advanced optical communication and imaging systems, yet conventional photodetectors suffer from low on-off ratios and limited polarization discrimination. Here, we report gate-tunable PdSe2/WSe2 van der Waals heterostructures that achieve ultrahigh light on-off ratio and polarization-sensitive photodetection. The heterostructure forms a type-II band alignment, enabling efficient charge separation and self-powered operation. By applying a gate voltage, the photoresponse can be modulated, achieving an on-off ratio exceeding 10^6 under illumination. The device exhibits a high responsivity of 1.2 A/W and a specific detectivity of 10^12 Jones at room temperature. Polarization-sensitive measurements reveal a linear dichroism ratio of 2.1 at 532 nm, attributed to the anisotropic crystal structure of PdSe2. The photodetector operates over a broad spectral range from visible to near-infrared (400-1000 nm) with fast response times (rise/fall < 100 μs). The gate-tunable capability allows dynamic control of the photocurrent, enabling adaptive sensing applications. These results demonstrate that PdSe2/WSe2 heterostructures are promising candidates for high-performance, polarization-sensitive photodetectors, offering a pathway for next-generation optoelectronic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4292-4
The vast compositional space of high-entropy materials presents a fundamental challenge for catalyst discovery. Considering 21 candidate elements at a 1% atomic resolution, this combinatorial explosion exceeds 10 billion (>10^10) possibilities, rendering direct experimental exploration impractical. Furthermore, purely data-driven approaches often struggle to comprehend the intrinsic chemical roles of discrete elemental identities, yet they excel at mapping continuous concentration gradients. Recognizing this distinction, we transform this combinatorial explosion into a targeted optimization problem by decoupling elemental selection from compositional ratio refinement. Ultrafast carbon thermal shock (CTS) is first employed to screen viable elemental combinations and establish an optimal quinary framework. Machine learning (ML) is subsequently applied to optimize compositional ratios within this reduced space, where statistical modeling efficiently navigates the remaining high-dimensional landscape. Targeting the oxygen evolution reaction (OER) as a proof-of-concept, our hybrid framework pruned the search space from over 10^10 possible compositions down into 13 systems, ultimately identifying high-entropy oxide (HEO)-Fe17.57Co28.45Ni31.27Mo10.57Zr12.14 as the optimal catalyst. The optimized high-entropy oxide exhibits an overpotential of 240 mV at 10 mA cm−2 and sustains stable operation at 1 A cm−2 for over 600 h in 1 M KOH. Mechanistic analysis reveals that Mo electronically tunes oxygen-intermediate adsorption, while Zr enhances structural robustness, collectively enabling high activity and durability. This work demonstrates that bridging discrete physical screening with continuous data-driven optimization provides an efficient and generalizable pathway for navigating high-dimensional material frontiers.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4385-1
Self-assembled monolayers (SAMs) are effective hole-selective contacts for inverted perovskite solar cells, but scalable deposition on rough substrates is hindered by molecular aggregation, disordered packing, and incomplete adsorption. We propose a hybrid strategy incorporating 4-(Piperidin-4-yl)butanoic acid hydrochloride (PBACl) into the 4PABCz solution during dip-coating. PBACl suppresses aggregation via hydrogen bonding and ionic interactions, yielding homogeneous coverage and improved wettability. The piperidine and carboxyl groups passivate buried interfacial defects through hydrogen bonding and coordination with perovskites. Small-area cells achieve a champion power conversion efficiency (PCE) of 26.09%, while a 5 cm × 5 cm mini-module (aperture area 14.4 cm²) delivers 23.29% PCE. Encapsulated devices retain 80% of initial PCE after 1350 h maximum power point tracking under continuous illumination. This ion modulation strategy bridges molecular-level interface control with scalable processing, offering a pathway to industrially relevant perovskite photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4315-2
High-temperature X-ray imaging demands scintillators with high crystallinity, efficient scintillation, and robust thermal stability, yet suitable materials remain scarce. Here, we report an ultra-high-crystallinity transparent glass-ceramic (GC) scintillator strategically designed via controllable heat-treatment-induced crystallization. A sequential precipitation method is employed, where cubic CaF2 nanocrystals initially form, subsequently promoting heterogeneous nucleation and growth of hexagonal BaAl2Si2O8. Intrinsic nanoscale phase separation into F-rich and O-rich domains significantly reduces atomic diffusion distances, yielding an unprecedented crystallinity of up to 97.6%. Notably, defect traps (oxygen vacancy defects, likely located within the lattice or at crystalline/amorphous interfaces) enable efficient carrier capture and thermally stimulated release, contributing to remarkable resistance to thermal quenching. Consequently, the GC scintillator maintains 90.6% of its integrated X-ray excited luminescence (XEL) intensity at 300 °C, with the integrated XEL intensity reaching 94.2% of commercial Bi4Ge3O12 (BGO) at room temperature. This enables stable high-temperature X-ray imaging with a spatial resolution of ~10.4 lp mm−1 up to 225 °C. This work provides a versatile pathway for developing high-sensitivity scintillators for extreme-environment X-ray imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4179-x
Perylene diimide (PDI) radical anions exhibit poor environmental stability, restricting their generation efficiency and practical application. Here, a PDI-functionalized bispillar[5]arene (PDI-P5) was designed to construct stable and high-efficiency photothermal radicals. Intramolecular charge transfer (ICT) between PDI and bispillar[5]arene narrows the energy gap. Under 455 nm ultraviolet light irradiation and diethylamine (DEA) vapor exposure, photoinduced electron transfer (PET) efficiently generates PDI-P5·− radicals, which possess broad near-infrared (NIR) absorption, enhanced non-radiative transitions, and excellent stability. Notably, PDI-P5·− can rapidly reach 90 °C under 0.20 W cm−2 simulated sunlight irradiation. Moreover, it exhibits superior multi-step photothermal anti-counterfeiting performance. This work provides a novel strategy for the development of stable radical-based photothermal materials, which holds great potential for anti-counterfeiting and bioimaging applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4151-2
The rapid increase in atmospheric CO2 due to fossil-fuel consumption has heightened the demand for efficient carbon capture and utilization technologies. Ionic liquids (ILs) have emerged as versatile media and catalysts for CO2 conversion, offering advantages such as negligible volatility, wide electrochemical windows, and strong CO2 affinity. However, the vast design space of ILs and limited experimental data make traditional trial-and-error screening inefficient. This review summarizes recent advancements in applying machine learning (ML) to the design and screening of ILs for CO2 conversion. The roles of ILs in catalytic processes and the limitations of traditional screening methods are discussed. ML-based workflows are explored, with emphasis on addressing challenges posed by small and noisy datasets. Finally, future opportunities in mechanism-informed descriptors, multi-objective optimization, and the integration of domain expertise with data-driven approaches are highlighted to accelerate the discovery of next-generation ILs for sustainable CO2 conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4106-8
Perovskite/organic tandem solar cells (PO-TSCs) have emerged as a compelling photovoltaic architecture to transcend the Shockley-Queisser limit of single-junction devices. By monolithically stacking a wide-bandgap (WBG) perovskite top cell and a narrow-bandgap (NBG) organic bottom cell, PO-TSCs enable broad spectral utilization and reduced thermalization loss, offering a viable pathway toward efficiencies beyond 30%. Their solution processability, compatibility with orthogonal solvents, and potential for lightweight, flexible, and semi-transparent modules further make them attractive for building integrated and portable electronics. However, the realization of high-performance PO-TSCs critically depends on precise carrier regulation across the entire multilayer stack, where inefficient charge transport, recombination losses, and interfacial bottlenecks often limit the overall power conversion efficiency (PCE) and stability. This review systematically examines the carrier-regulation strategies essential for advancing PO-TSCs, focusing on defect and phase-control in WBG perovskites, the design of optically transparent and electrically efficient interconnecting layers, and the enhancement of charge generation and collection in organic subcells. The integration of these approaches has recently enabled efficiencies exceeding 26%, demonstrating the rapid progress of the field. Ultimately, we conclude with an outlook on the remaining challenges in scalability, operational stability, and manufacturability, providing a roadmap for future research toward commercially viable tandem photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4114-5
The precise and controllable synthesis of one-dimensional (1D) and two-dimensional (2D) heterostructures, coupled with the manipulation of their atomic and electronic configurations, is of paramount significance. However, due to the synthetic challenges associated with graphyne (GY) materials, their integration into 1D/2D heterostructures remains considerably difficult. Herein, we demonstrate a post-synthetic intercalation strategy for tellurium onto Ag(111), enabling the controllable fabrication of 1D-GY-nanowire/2D-AgTe-monolayers heterostructures. Scanning-probe microscopies are employed to characterize morphological evolution during the intercalation process. Scanning tunneling spectroscopy results confirm that AgTe monolayer intercalation induces interfacial decoupling of the graphyne nanowires. Density functional theory calculations demonstrate that work function-driven Fermi level modulation via interfacial charge engineering assigns the 1D-GY-nanowire/2D-AgTe-monolayers heterostructures as type-I heterostructures. Our work not only significantly advances the fundamental understanding of interfacial interactions in 1D/2D heterostructures but also presents a scalable strategy for designing heterostructures with tailored electronic functionalities, thereby opening new avenues for applications in advanced nanoelectronics and optoelectronic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4337-2
Silica aerogels are recognized as leading super-insulating materials due to their ultralow thermal conductivity, yet their intrinsic brittleness and poor processability restrict practical deployment in complex industrial and extreme environments. This study introduces a macro-scale 'stiff–soft' synergistic strategy, combining a macroscopically processable, soft-and-tough framework as the load-bearing component with hard-and-brittle polymethylsilsesquioxane (PMSQ) aerogels as the insulating component. A pressure-driven assembly process enables viscosity-tunable PMSQ gel inks to be controllably infused into various hollow frameworks, including honeycomb panels, wheat straws, and hollow fibers. Guided by a modified Hagen–Poiseuille model, ink viscosity is precisely matched to the geometric parameters of the hollow structures. The resulting composites achieve compressive strength of 2.5 MPa, flexural strength of 6.25 MPa, and tensile strength of 40 MPa, while maintaining excellent thermal insulation. This versatile and scalable approach offers a new design paradigm for mechanically adaptive silica aerogel composites in thermal management applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4197-4
Deep-blue organic light-emitting diodes (OLEDs) remain the most challenging primary-color emitters due to stringent exciton energy requirements. We strategically designed two innovative deep-blue emitters, SCZ-4AnCN and STPA-4AnCN, via systematic functionalization of an anthracene core with arylamino-decorated spirofluorene donors and cyano-substituted phenyl acceptors. Comprehensive theoretical and experimental analyses demonstrate that these spirofluorene-anthracene hybrids adopt precisely engineered distorted configurations, effectively suppressing detrimental intermolecular π–π stacking in condensed phases. The sp3-hybridized bridgehead carbons in spirofluorene units play a pivotal role by simultaneously restricting π-conjugation extension and fine-tuning donor–acceptor interactions, thereby stabilizing the lowest excited singlet (S1) state with dominant local excitation (LE) character. This molecular engineering yields exceptional deep-blue emission with remarkable efficiency. Notably, the materials exhibit unique high-lying reverse intersystem crossing (hRISC) behavior, enabling efficient triplet harvesting. Optimized doped devices incorporating SCZ-4AnCN achieve outstanding performance, including a maximum external quantum efficiency (EQE_max) exceeding 10% and CIE coordinates (0.154, 0.052) approaching the BT.2020 blue standard. Nondoped devices maintain impressive performance with an EQE_max of 7.51% and superior operational stability, demonstrating less than 10% efficiency roll-off at 1000 cd m−2. This work validates anthracene-based molecular architectures for deep-blue electroluminescence and establishes a transformative design paradigm for next-generation OLED emitters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3865-1
Seawater electrolysis (SWE) is a reusable and convenient avenue for producing hydrogen, offering a promising solution to the energy crisis and global warming. However, poor electrolytic efficiency and irreversible corrosion caused by high concentrations of chlorine severely hinder the commercialization of SWE. To address these challenges, numerous strategies have been proposed in recent years, involving theoretical innovations, directional catalyst design, and electrolyser modification. This review provides a systematic summary of the chlorine-related challenges and solutions encountered in SWE. The chlorine-related theoretical knowledge and challenges in SWE systems are first emphasized. Subsequently, multiple anodic chloride suppression strategies are introduced from three aspects: directional regulation of oxygen evolution catalysts, optimization of electrolyte compositions, and ingenious upgrades of electrolytic cells. Finally, future challenges and development directions for large-scale application of SWE technology are explored. This review offers an in-depth analysis of the chlorine-related challenges encountered in the industrialization of SWE, aiming to accelerate the advancement of this technology toward practical applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3775-3
The urgent imperative for carbon-neutral chemical production has accelerated the development of solar-driven catalytic technologies that convert abundant C1 feedstocks (CO2 and CH4) into value-added C2+ molecules. Standalone photocatalysis remains constrained by rapid charge-carrier recombination and poor C–C coupling selectivity. This review critically examines multi-field-coupled catalysis—a transformative paradigm synergistically integrating solar energy with auxiliary thermal, electric, and magnetic fields. Through mechanistic dissection of photothermal, photoelectrochemical, and photomagnetic field cooperativities, it is summarized that thermal gradients attenuate phonon scattering to enhance charge-carrier drift mobility while vibrationally stabilizing reactive intermediates, electric potentials drive vectorial charge transport via Coulomb-force-directed separation and band alignment, and magnetic fields modulate spin-selective electron transfer through Zeeman splitting-mediated polarization to boost reaction specificity. This synergistic multi-field integration circumvents intrinsic limitations of single-mode photocatalysis by collectively reconfiguring reaction coordinates for selective C–C coupling. We further address persistent challenges in resolving ultrafast interfacial charge-transfer dynamics, scaling integrated field reactors for industrial deployment, and advancing in situ operando characterization of multiscale processes. Strategic research priorities are proposed to advance sustainable multi-field-coupled catalytic production of fuels and platform chemicals.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3588-2
The rapid evolution of aerospace technology necessitates the development of multi-functional composites that combine light weight, mechanical robustness, thermal protection/insulation, and electromagnetic interference (EMI) shielding. C/SiC porous ceramic composites are promising for thermal protection in hypersonic vehicles. Here, we report a facile strategy to fabricate Cf/SiC composite polymer-derived ceramics (PDCs) via re-pyrolysis of high-energy ball-milled polycarbosilane-vinyltriethoxysilane-graphene oxide (PVG) with Cf/SiC(rGO)p blend interleaves. In-situ generated honeycomb-like cellular structures and non-directional channels reduce density and increase porosity. High-quality SiO2 joints, formed from Si-dangling bonds, strengthen interfacial bonding via a brazing effect, while in-situ SiOC nanowires (SiOCnws) create a hierarchically enhanced network, improving fracture toughness and crack resistance. Multi-scale interfacial/dipole polarization enhances EMI shielding. The optimized Cf(0.2)/SiC(rGO) composite exhibits low density (1.49 g cm−3), high fracture toughness (6.32 MPa m1/2), hardness (7.18 GPa), compressive strength (72.67 MPa), and EMI shielding effectiveness of 58.31 dB. It maintains structural stability under butane blowtorch ablation at ~1300 °C for 3600 s. Porous variants show thermal conductivity of 0.211 W m−1 K−1 with 69.74% porosity. These multi-functional composites are promising for thermal protection systems in aerospace applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3676-3
Perovskite solar cells (PerSCs) have achieved remarkable efficiencies, yet their performance is limited by defect states and non-radiative recombination. Here, pyromellitic diimide (PD) is introduced as an additive to passivate bulk defects in perovskite films. PD forms hydrogen bonds with formamidinium (FA+) ions and coordinates with Pb2+ ions, effectively suppressing non-radiative recombination and reducing energy loss. The PD-treated perovskite films exhibit enhanced crystallinity and uniformity. Consequently, 1.55 eV PerSCs achieve a high open-circuit voltage (VOC) of 1.193 V and a power conversion efficiency (PCE) of 25.79%. Moreover, unencapsulated PD-treated devices retain 96% of their initial efficiency after 2000 h under nitrogen atmosphere, whereas control devices retain only 74%. Under ISOS-D-2I accelerated aging (65±5°C in N2), PD-treated devices show less than 5% PCE attenuation after 288 h, compared to ~30% for controls. This work provides a viable strategy for defect passivation in perovskite solar cells, enhancing both efficiency and stability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3793-9
Organic solar cells (OSCs) require both a high donor/acceptor (D/A) interfacial area for efficient exciton dissociation and a vertically phase-separated morphology for efficient charge transport. Traditional bulk heterojunctions (BHJs) provide large interfacial areas but lack vertical phase separation, while quasi-planar heterojunctions (QPHJs) achieve vertical separation at the cost of reduced interfacial contact. Here, we introduce an in situ pore-forming strategy for polymer thin films. By incorporating an excess of additives as pore-forming agents into the donor layer, a nanoporous film with a fibrous nano-network is generated. Subsequent deposition of acceptor molecules fills these nanopores, creating a hybrid planar/bulk heterojunction (HP/BHJ) that synergizes the strengths of both architectures. This design enhances performance by: (1) increasing the D/A interfacial area via nanopores, forming a three-dimensional network that accelerates exciton dissociation; (2) promoting close molecular packing that minimizes carrier recombination and establishes low-defect charge transport channels; and (3) fostering vertical phase separation through layer-by-layer deposition. Binary OSCs fabricated with this strategy achieve a power conversion efficiency (PCE) of 20.0%, surpassing conventional BHJ and QPHJ devices by a significant margin. The approach demonstrates general applicability, with analogous improvements observed in D18/BTP-eC9-4F and PM6/L8-BO systems, underscoring its potential for advancing OSC performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3604-1
Piezoelectric materials convert mechanical energy into electrical signals, enabling applications in sensors, actuators, and energy harvesting. Inorganic ceramics like PZT and BTO exhibit excellent piezoelectric properties but are brittle, limiting their use in flexible electronics. This work presents a porous composite of PZT@carboxymethyl chitosan (CMCS) in thermoplastic polyurethane (TPU). The core-shell structure enhances interfacial compatibility, while the porous TPU skeleton facilitates stress transfer and amplification, allowing high piezoelectric content. The resulting PZT@CMCS/TPU devices achieve an output voltage of 53 V and current of 13 μA, an 11-fold improvement over conventional PZT composite films. This approach enables flexible piezoelectric devices with high performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3538-6
The understanding of anion transporting behaviors under sub-nanoconfined regimes can guide the design of high-performance anion selective membranes (ASMs), yet it is little known. Here, we build membrane channels that combine physical rigidity with chemical affinity to anions simply through bridging graphene oxide nanosheets with charged linkers. We observe that the rigidly confined interaction imposed by channels to anions can reconfigure hydration shells in varying degrees for different anions via compensating for hydration-induced energy barriers and differentiating their rearrangement behaviors. During the configuration evolution, water molecules within hydration shells would rotate and simultaneously change their distance from the ion center. Based on the big discrepancy in configuration evolution, these membranes can realize ultrahigh selectivity of, for example, 125 for Cl−/SO4^2− and surpass the performance upper bound concerning Cl−/SO4^2− separation by other membranes. The knowledge of the configuration change of hydration shells during the dehydration process will be key to designing next-generation ASMs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3552-2
Perovskite light-emitting diodes (PeLEDs) are a promising display technology due to high color purity and solution processability, but their operational stability is compromised by environmental degradation. Encapsulation is essential for practical deployment. Here, we report that applying a commercial AB epoxy adhesive as a cover encapsulant induces a striking transparency transition in Cs0.3MA0.7PbBr3 perovskite films, from yellow to optically clear. The effect is attributed to the alkaline hardener (component B, pH 9–10), which engages in Lewis acid-base coordination with Pb2+ and reacts with Br−, as evidenced by Fourier-transform infrared spectroscopy (redshift of C–O–C stretch from 1035.56 to 1018.05 cm−1, Δν ≈ 17.5 cm−1) and X-ray photoelectron spectroscopy (Pb 4f shift of 0.25 eV, Br 3d5/2 shift of 0.45 eV). This chemical interaction refines perovskite grains to tens of nanometers, shifting light scattering from Mie to Rayleigh regime and enhancing transmittance. Encapsulated devices achieve a maximum luminance of 12,643 cd/m2, a low operational current density, and an increased breakdown voltage of 27 V. The work establishes a framework for selecting encapsulation materials that impart transparency, enabling applications in transparent displays, smart windows, and augmented reality.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3623-y
Organic light-emitting diodes (OLEDs) are an advanced technology for full-color displays, yet the low efficiency of blue OLEDs remains a critical bottleneck. Here, we report a new strategy to design robust Pt(II) emitters with enhanced molecular rigidity and increased locally excited character. The resulting Pt(II) emitter exhibits an extremely narrow emission spectrum peaking at 458.6 nm with a full-width at half-maximum (FWHM) of 16.0 nm and a small Huang-Rhys factor of 0.278, together with a high photoluminescence quantum efficiency of 95%. When doped into an OLED, the device emits at 464 nm with high color purity (FWHM = 19 nm) and achieves high external quantum efficiencies (EQEs) of 32.6%, 29.4%, and 26.9% at luminances of 123, 1000, and 5000 cd/m2, respectively. Notably, the device attains a record-high maximum brightness of 84,895 cd/m2 among reported deep-blue OLEDs with Commission Internationale de l'Éclairage (CIE) y-coordinate < 0.15. This work demonstrates one of the highest-performing deep-blue OLEDs reported to date, addressing the dual challenges of efficiency and brightness in this spectral region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3677-9
The demand for high-performance scintillators in high-temperature applications, such as industrial flaw detection and oil exploration, necessitates materials with both high efficiency and thermal robustness. This work reports Tb3+-doped oxyfluoride glass scintillators exhibiting anti-thermal-quenching radioluminescence (RL). Three synergistic strategies were employed: (i) an oxyfluoride glass host providing a low-phonon-energy environment, (ii) increased structural densification of the glass network, and (iii) thermally enhanced energy transfer from Ce3+ to Tb3+. The resulting scintillators achieve an optical transmittance exceeding 88% at 542 nm, a record RL intensity of 350% relative to a standard Bi4Ge3O12 (BGO) crystal, and an imaging resolution of 24 lp mm−1. Notably, the RL intensity at 633 K reaches 143% of its room-temperature (303 K) value, demonstrating significant anti-thermal-quenching behavior. In contrast, commercial BGO and CsI:Tl scintillators exhibit RL intensities dropping to approximately 1% under identical conditions. These results establish the potential of Tb3+-doped glass scintillators for high-temperature X-ray imaging and provide a strategic framework for developing thermally robust scintillating materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3642-4
High-density glass scintillators are promising alternatives to crystals for next-generation radiation detection due to their low cost, excellent physical and chemical stability, and processability. In this study, a series of Ce3+-activated gadolinium gallium borosilicate (GGBS x) glasses were synthesized via vacuum melt-quenching. With increasing Gd2O3 content, glass density increased from 5.86 to 6.05 g/cm3, and molar volume from 36.43 to 39.79 cm3/mol. Extended X-ray absorption fine structure (EXAFS) analysis revealed that in GGBS 1 glass, Ce3+ exclusively adopts a hexahedral [CeO6] configuration, while Gd3+ exhibits both hexahedral and octahedral coordination with a bond length of 2.35±0.1 Å and Debye-Waller factor σ2 of 0.0122±0.0015 Å2. As Gd2O3 content increased, shallow trap depth rose from 0.804 to 0.858 eV, while deep trap depth first increased from 0.948 to 1.434 eV then decreased to 1.010 eV. GGBS 1 glass exhibited high transmittance (~80%) in the visible range and a photoluminescence quantum yield of 78.4%. Under X-ray irradiation, its X-ray excited luminescence intensity reached 128.5% of that of Bi4Ge3O12 (BGO) crystal, with a spatial resolution of 29.1 lp/mm, approaching the highest reported for glass scintillators. Under γ-ray excitation, it achieved a light yield of 1058 photons/MeV and an energy resolution of 23.7% at 662 keV. These results indicate that GGBS 1 glass scintillator warrants further development for applications in X-ray imaging and γ-ray spectroscopy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3610-7
Electrochemical CO2 reduction reaction (CO2RR) offers an attractive route to produce value-added multicarbon (C2+) products, yet suffers from competing hydrogen evolution and monocarbon production. Here, we propose a dual-confinement effect on CO2 reactant and *CO intermediate, induced by tuning the pore configuration of reconstructed covalent organic frameworks (RC-COFs). The highly crystalline microporous RC-COF-1, when coated on a Cu electrode, enhances local CO2 concentration and restricts CO diffusion, thereby promoting C-C coupling. In acidic electrolyte, the RC-COF-1@Cu electrode achieves a maximum C2+ Faradaic efficiency (FE) of 67.0% at 500 mA cm−2, while maintaining a total carbon product FE above 90% across a broad current density range (100–500 mA cm−2). Experimental and theoretical analyses confirm that the ordered micropores of RC-COF-1 modulate reactant adsorption and intermediate diffusion, leading to improved C2+ selectivity. This work underscores the critical role of COF pore architecture in microenvironment engineering for heterogeneous catalysis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3637-6
Traditional optical fiber communication encryption methods lack sufficient dynamic adaptability and hardware flexibility, while reconfigurable logic gates can overcome this limitation, thereby significantly improving the flexibility of encryption systems. This study reports a reconfigurable optoelectronic logic gate (OELG) system based on hafnium-zirconium oxide (HZO) ferroelectric thin films. Through ultra-low temperature atomic layer deposition technique, the fabricated HZO thin films demonstrate an exceptional pyroelectric coefficient of 1835.91 μC m−2 K−1 and robust multi-level polarization stability, enabling efficient broadband photon-to-current conversion. By leveraging the pyroelectric effect and tunable polarization states, the OELG device achieves dynamic optical signal modulation and logic processing. The OELG device supports five fundamental logic operations (AND, OR, NAND, NOR, NOT) via electrical bias and polarization control, without requiring hardware modifications. The OELG device demonstrates stable performance over 10^9 cycles with no degradation, meeting practical application requirements. Furthermore, a convolutional neural network (CNN)-integrated image encryption-decryption framework was validated, achieving 95.01% recognition accuracy on decrypted data, while unauthorized decryption attempts resulted in significant feature loss. This study addresses security challenges in optical communication networks by proposing an innovative solution that integrates pyroelectric materials with reconfigurable logic gate technology, offering a new pathway to enhance physical-layer security.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3687-6
P2-Na0.67Ni0.33Mn0.67O2 (NNMO) is a promising cathode for sodium-ion batteries (SIBs) due to its high energy density and operating voltage. However, severe P2-O2 phase transition at high cut-off voltage causes large volume variation, structural degradation, and rapid capacity decay. Ion doping has been explored to suppress this transition, but achieving both high capacity and stability remains challenging. Here, we demonstrate that precise composition regulation enables both. The designed P2-Na0.67Ni0.28Mg0.03Fe0.04Mn0.55Ti0.1O2 retains high electrochemical active element content while effectively suppressing phase transition, leading to outstanding structural stability and fast charge transfer kinetics. This cathode delivers a high specific capacity of 143.5 mAh g−1 at 0.1 C and maintains stable cycling over 1000 cycles. Our work provides a new strategy for rationally designing high-capacity, stable cathode materials for SIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3672-8
Pore-tuning engineering is an effective strategy for designing catalysts for energy storage and conversion. Here, we report a rhombic dodecahedral iron and nitrogen co-doped carbon (Fe-N-C) material with hierarchical micro-mesoporous structures, synthesized using mesoporous silica as both pore template and iron source. The resulting catalyst (m-Fe/NC) exhibits significantly enhanced oxygen reduction reaction (ORR) activity, with half-wave potentials of 0.81 V and 0.88 V in acidic and alkaline media, respectively. When employed as a cathode in zinc-air batteries, m-Fe/NC delivers a superior specific capacity of 815 mAh g_Zn^-1 and a stable cell voltage of 1.31 V at a current density of 10 mA cm^-2. Advanced characterization and theoretical calculations reveal that the mesoporous structure not only increases active site exposure but also induces a curvature-induced strain effect on concave surfaces, which enhances intrinsic activity. This work provides insights for developing innovative nanoporous electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3733-2
Irreversible sodium loss, primarily caused by solid electrolyte interphase (SEI) formation during initial cycling, significantly degrades the capacity of sodium-ion batteries by depleting active sodium. While pre-sodiation mitigates initial sodium loss, it fails to address continuous loss throughout the battery lifecycle. To overcome this limitation, we propose a sustained sodium compensation strategy utilizing activation-releasing systems. Key to this approach are high-capacity sodium compensators, Na2C2O4 and Na2C4O4, supported on a B and N co-doped Mo2C-W2C (MoW-C) heterostructure catalyst. This configuration enables efficient sodium release at charging voltages of 3.53 and 3.78 V, respectively. By integrating the sodium supplement agent onto the separator, and precisely controlling voltage and charge, multiple sodium replenishment is achieved over the entire battery lifecycle. This strategy reduces initial active sodium loss by 36.53%. Furthermore, a single activation during subsequent usage provides an additional 0.115 mAh cm−2 of active sodium. As a result, the cell exhibits exceptional cycling stability, with a capacity loss of only 0.059% per cycle over 350 cycles at 0.5 C.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3719-8
The proliferation of 5G communications and smart electronic devices has intensified electromagnetic wave (EMW) pollution, necessitating microwave absorption materials (MAMs) with high efficiency, lightweight, and flexibility. Traditional MAMs suffer from high density and narrow effective absorption bandwidth (EAB). This work presents a lightweight, flexible microwave-absorbing composite fabricated by in-situ polymerization foaming of polyurethane (PU) with multi-walled carbon nanotubes (MWCNTs) and flaky carbonyl iron (FCI). The hierarchical PU composite foam, designated 3*PFC 0.5-1.0-1.5, achieves an EAB of 15.7 GHz, covering 98.1% of the tested 2–18 GHz range, including S, C, X, and Ku bands. This performance stems from synergistic conductive and magnetic losses, along with impedance matching facilitated by the hierarchical porous structure. The composite maintains low density and high compressibility, offering a promising solution for EMW absorption in 5G, military stealth, and smart devices. The in-situ method ensures strong interfacial adhesion between fillers and matrix, enhancing durability compared to impregnation methods. This study demonstrates a scalable approach to fabricate high-performance MAMs with broad bandwidth and mechanical robustness.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3686-6
Fused silica (SiO2) exhibits exceptional thermal stability and dielectric properties, making it an attractive material for aerospace and military applications. However, its relatively poor mechanical performance has limited its widespread practical utilization. This study proposed an innovative approach to fabricate SiO2-hexagonal boron nitride (hBN) composite ceramics via spark plasma sintering (SPS), leveraging the high-temperature phase transformation of cubic boron nitride (cBN) to introduce randomly oriented hBN as a reinforcing phase within the SiO2 matrix. The randomly oriented hBN nanoplates allow cracks to propagate along stronger grain boundaries, rather than along weaker interlayers of hBN, significantly improving the overall strength and fracture toughness of the composite. The maximum flexural strength and fracture toughness achieved are 183.4 MPa and 2.06 MPa m1/2 respectively, which are 3.6 times and 4 times that of fused SiO2. Concurrently, the composites exhibit low dielectric constants (ε = 3.58–3.69) and dielectric losses (tan δ < 0.0087) at 1 MHz. This work successfully enhanced the mechanical performance of fused SiO2 while preserving its excellent dielectric characteristics, opening new possibilities for its potential applications in advanced structural and functional fields.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3652-2
Existing robotic end-effector gripping technologies often encounter challenges such as poor adaptability to environmental changes, incomplete deformation sensing, and insufficient adhesion stability, which can compromise operational safety and reliability. Here, we present the bio-inspired self-sensing suction cup, in which the core self-sensing capability is achieved by combining high-performance, laser-induced graphene/Ag NWs flexible sensors with a Wheatstone bridge design. The flexible sensors provide high sensitivity, while the Wheatstone bridge circuit enables accurate and stable detection of deformation during the gripping process. Integrated into the octopus-inspired suction cup, this system allows for real-time monitoring of deformation and adsorption stability. The self-sensing suction cup demonstrates good performance across a 0–25 kPa negative pressure range, with outstanding linearity (R2 = 0.993) and high sensitivity (GF = 10.436 kPa−1). Experimental results confirm that the suction cup can achieve stable adsorption under varying loads and enable real-time monitoring of the suction cup status during the gripping process. This design provides a promising solution for intelligent gripping systems, logistics, and object recognition in challenging environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3679-8
Idiopathic pulmonary fibrosis (IPF) is a chronic interstitial lung disease with high mortality and limited therapeutic options. Dysregulated macrophage polarization drives fibroblast activation and epithelial-mesenchymal transition (EMT), yet no effective management exists. Here, we develop an inhalable methane nanocapsule (MNC) that spatiotemporally controls methane release in the lung to remodel the fibrogenic microenvironment. MNC is formulated via self-assembly of biodegradable poly(lactic-co-glycolic acid)-polyethylene glycol (PLGA-PEG) and a novel acid-responsive methane prodrug Fe(BPY)2(CH3)2, enhancing mucosal penetration and sustained methane release in acidic inflammatory niches. In a bleomycin (BLM)-induced pulmonary fibrosis model, MNC inhalation achieves efficient lung deposition and sustained methane release, significantly reducing inflammation, ameliorating fibrosis, and improving lung function without systemic side effects. Mechanistically, MNC rebalances macrophage polarization by inhibiting M2 phenotype overexpression and downregulates the MMP9/TIMP-1 ratio to suppress myofibroblast proliferation and EMT, synergistically halting fibrotic progression. This inhalable methane nanocapsule offers a promising strategy for safe and effective IPF treatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3598-1
Embedding a dielectric layer between as-synthesized graphene nanoribbons (GNRs) and metal surfaces represents a powerful strategy to achieve electronic decoupling, thereby enabling the extraction of these ribbons' intrinsic electrical properties. Although several reports have documented dielectric intercalation between GNRs and metal substrates, studies on Ag(111) substrates are limited. Here, we demonstrate a semiconducting AgTe monolayer intercalation method to achieve electronic decoupling between as-synthesized GNRs and an Ag(111) substrate. Using low-temperature scanning tunneling microscopy, we directly observed the AgTe intercalation process at the GNR/Ag(111) interface. By combining scanning tunneling spectroscopy and density functional theory calculations, we elucidate the critical role of AgTe monolayer intercalation in reducing the interaction between as-synthesized GNRs and the Ag(111) substrate and observe the near-intrinsic electrical properties of the GNRs. Our findings offer a practical and effective strategy for intercalating AgTe monolayers between carbon-based nanomaterials and Ag(111) substrates, facilitating the unambiguous characterization of the near-intrinsic electronic properties of these materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3653-2
Designing photosensitizers with efficient intersystem crossing (ISC) and long-lived triplet excited states is critical for photodynamic therapy (PDT). However, conventional molecular design principles often rely on heavy-atom effects or specific donor-acceptor architectures, limiting generality. Here, we report a facile and rational strategy to convert intrinsically non-photosensitizing fluorophores into effective reactive oxygen species (ROS) generators by introducing guanidinium substituents. The modified photosensitizers exhibit prolonged triplet excited state lifetimes and considerable ROS production, in stark contrast to unmodified fluorophores which show intense fluorescence and negligible ROS generation. Electron paramagnetic resonance spectroscopy and high-resolution mass spectrometry confirm the formation of stable nitrogen-centered radical cations on the guanidinium moiety, stabilized by p-π conjugation. Mechanistic studies indicate that these radicals promote ISC and prolong triplet state lifetimes. In vitro and in vivo experiments demonstrate that guanidinium-modified photosensitizers induce immunogenic cell death (ICD) and elicit potent anti-tumor immunity. This work provides a universal and facile strategy for designing organic photosensitizers through stable radical cation-containing building blocks, expanding the scope of PDT agents.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3503-9
This correction addresses an image misuse in the original publication (Sci China Mater, 2025, 68(6): 2095, DOI: 10.1007/s40843-025-3311-6). Specifically, a fluorescent image in Fig. 4d, depicting live/dead cells after treatment with MPDA@TMZ without laser irradiation, was erroneously presented. The corrected Fig. 4 is provided, and the authors confirm that the results and conclusions of the original paper remain unaffected. The correction ensures the integrity of the reported data, particularly the cell viability and apoptosis assays. The study focuses on mesoporous bowl-shaped polydopamine (MPDA) nanoparticles co-loaded with temozolomide (TMZ) and indocyanine green (ICG) for synergistic glioblastoma therapy. The corrected figure includes CLSM images of G422 cells after incubation with various formulations (ICG, sPDA@ICG, mPDA@ICG, MPDA@ICG), cell viability curves, quantitative fluorescence intensity, live/dead staining, and apoptosis quantification. Statistical significance is denoted as ****p < 0.01. The correction maintains the scientific validity of the findings, which demonstrate the potential of MPDA-based nanoplatforms for combined chemo-photothermal therapy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3780-3
Real-time health monitoring and ongoing evaluation of physiological conditions are becoming increasingly vital for the advancement of future medical diagnostics and personalized healthcare solutions. Given that certain illnesses necessitate prompt and accessible detection methods, wearable chemical sensors have garnered considerable interest for their capability to monitor health through physiological signals and chemical indicators. This review delivers a thorough examination of recent developments in four primary categories of wearable chemical sensors: biosensors, humidity sensors, gas sensors, and ion sensors. We explore the representative materials, device structures, operating mechanisms, and various application scenarios for each type of sensor. By investigating the latest innovations in these technologies, we aim to provide a detailed overview of the current research landscape, highlight existing challenges, and present potential future directions of wearable chemical sensors in healthcare monitoring.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3757-2
β-Ga2O3 is a promising candidate for solar-blind ultraviolet photodetection owing to its suitable bandgap of approximately 4.9 eV, excellent photoresponse characteristics, and high stability. However, the lack of a sufficient driving force within the material leads to extensive bulk charge recombination, limiting its photocurrent and thus posing significant challenges in designing high-performance Ga2O3-based photodetection. In this study, we propose a gradient doping strategy to achieve a Sn-doping concentration gradient along the β-Ga2O3 film thickness. By combining sol–gel synthesis with rapid thermal annealing, a spatially graded band structure with a full-space built-in electric field is constructed, which increases the width of band bending over a large region and is crucial for significantly enhancing carrier separation and transport in the bulk. The resulting gradient Sn-doped β-Ga2O3 enables exceptional photoelectric performance without an external bias under 254 nm irradiation, including a superior responsivity of 66.88 mA W−1, a high detectivity of 8.12 × 10^11 Jones, and a fast rise/decay time of 79/65 ms, outstanding most existing similar reported photoelectrochemical (PEC) type optoelectronic devices. Additionally, the device exhibits excellent long-term stability and enables high-resolution underwater ultraviolet imaging. This study demonstrates that the gradient doping strategy provides a feasible approach for enhancing the PEC performance of β-Ga2O3 photoelectrodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3710-y
Layered transition metal oxide cathodes for sodium-ion batteries (SIBs) suffer from Jahn–Teller distortion of MnO6, Na+/vacancy ordering, and irreversible lattice oxygen loss, causing capacity fading and voltage decay. Here, we report a P2-type material, Na0.67Ni0.3Mn0.6Li0.09Sn0.01O2 (NNMO-Li0.09Sn0.01), co-doped with closed-shell Li+ and Sn4+ ions. Li+ increases the Mn4+/Mn3+ ratio, mitigating Jahn–Teller distortion, and disrupts Ni/Mn ordering, suppressing Na+/vacancy ordering. Sn4+ forms stronger Sn–O bonds (548 kJ mol−1), enhancing bonding between transition metal ions and oxygen, reducing oxygen loss. NNMO-Li0.09Sn0.01 delivers a specific capacity of 90.3 mAh g−1 with 62.9% capacity retention after 50 cycles at 0.1 C (1 C = 200 mA g−1), and 90.3% voltage retention. This closed-shell substitution strategy offers a viable approach for enhancing structural stability of wide-voltage layered oxide cathodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3685-7
NiMo-based catalysts are promising for the hydrogen evolution reaction (HER), yet optimizing their electronic structure and enhancing mass transfer remain challenging. Here, we report a route to synthesize two-dimensional (2D) porous Mo2N-Ni heterojunction nanosheets with tuned Ni/Mo ratio for enhanced alkaline HER. The precursor is assembled from polyoxometalate clusters (PMo12) and layered Ni(OH)2. The interaction between PMo12 and Ni(OH)2 suppresses particle agglomeration during pyrolysis, yielding 2D porous sheets composed of small Mo2N-Ni units. Electron transfer from Ni to Mo2N redistributes electrons at the heterojunction, optimizing intermediate adsorption/desorption. The porous structure enhances mass transfer, reducing catalyst impedance. The optimized catalyst exhibits an overpotential of 19 mV at 10 mA cm−2, comparable to commercial Pt/C. An anion exchange membrane (AEM) electrolyzer pairing this catalyst with NiFe-LDH achieves 500 mA cm−2 at 1.80 V and operates stably for 300 h. This assembly method offers a scalable strategy for efficient catalyst production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3805-1
The sluggish kinetics of oxygen reduction and evolution reactions (ORR/OER) at the air electrode impede the practical deployment of fiber zinc-air batteries (FZABs) for wearable electronics. Conventional bifunctional catalysts suffer from an inherent activity trade-off due to the distinct mechanisms of ORR and OER. Here, we propose a spatial decoupling strategy to overcome this limitation by engineering isolated Fe single atoms and Fe–Ir dual-atom pairs on a nitrogen-doped carbon matrix (Fe/FeIr-NC). In this architecture, Fe single atoms serve as ORR centers, while Fe–Ir pairs with tunable spacing are tailored for OER, enabling complete functional separation and independent optimization. The catalyst exhibits an ORR half-wave potential of 0.91 V and an OER overpotential of 250 mV at 10 mA cm−2, yielding a record-low bifunctional gap (ΔE = 0.57 V) that outperforms all reported single- and dual-atom catalysts. A flexible fiber zinc-air battery based on this catalyst delivers a peak power density of 3920 W kg−1, along with a 1.4-fold increase in energy efficiency and a 2.6-fold extension in cycle life compared to the commercial Pt/C + IrO2 benchmark. This work not only breaks the traditional activity trade-off in bifunctional catalysis but also offers a promising route toward high-performance power sources for wearable electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3773-7
Kesterite Cu2ZnSn(S,Se)4 (CZTSSe) solar cells suffer from significant open-circuit voltage (VOC) deficits due to severe interfacial and bulk recombination, restricting their power conversion efficiency (PCE) far below the Shockley-Queisser limit. This work proposes a low-temperature annealing strategy during ITO sputtering (SA) to synergistically address these challenges. The temperature applied during ITO sputtering not only improves the crystallinity, carrier concentration, and optical transmittance of the ITO layer but also promotes the diffusion of In from ITO into both CdS and CZTSSe layers. Consequently, lattice matching at the CZTSSe/CdS interface is optimized, enabling epitaxial growth. And a favorable ITO/In:CdS/In&Cd:CZTSSe structure with optimal band alignment is obtained. As a result, a champion device with a PCE of 14.29% was achieved. The SA-treating also enabled the CZTSSe solar cells to achieve the highest VOC reported to date, exceeding 590 mV. This underscores the essential role of SA processing in optimizing interface engineering and suppressing defects, thus promoting the development of low-cost, high-performance kesterite photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3795-x
Two-dimensional MXene Ti3C2Tx demonstrates great promise in perovskite solar cells (PSCs). Herein, sulfur-terminated Ti3C2Tx (S-Ti3C2Tx) is developed by modifying Ti3C2Tx via a facile hydrothermal method using thioacetamide. As a perovskite additive, S-Ti3C2Tx outperforms pristine Ti3C2Tx by (1) significantly promoting grain growth, enhancing carrier mobility, and reducing defect density; (2) optimizing energy level alignment to lower interfacial energy barriers and minimize interface non-radiative recombination; (3) stabilizing uncoordinated Pb2+ and [PbI6]4− octahedra via Pb–S bonds while alleviating bulk lattice strain, as this Pb–S interaction exerts a “tape-like” effect. Based on this synergistic mechanism, PSCs with S-Ti3C2Tx achieve a champion efficiency of 25.51%—outperforming control (23.46%) and pristine Ti3C2Tx-based devices (24.54%)—with enhanced stability. This work highlights terminal group engineering as a critical strategy for advancing high-performance PSCs and their potential for emerging photovoltaic technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3767-9
Progressive skin fibrosis ultimately results in irreversible contractures, causing both joint dysfunction and cosmetic deformity. The key pathological features of skin fibrosis include persistent inflammation and abnormal accumulation of the extracellular matrix (ECM), with epithelial-mesenchymal transition (EMT) playing a critical role in disease progression. However, current therapeutic strategies for cutaneous fibrosis are largely palliative and often require repeated interventions, with limited efficacy. Celastrol (Cel) exerts anti-inflammatory and anti-fibrotic effects in skin tissue, but its clinical application is limited by poor bioavailability and a narrow therapeutic window. Tetrahedral framework nucleic acid (tFNA), a novel nanocarrier system, exhibits multiple advantages, including enhanced cellular uptake, improved cell viability, and intrinsic anti-fibrotic and anti-inflammatory properties. Therefore, this study applied tFNA-Cel complex (TCC) as an advanced nanotherapeutic agent, designed to exert a synergistic anti-fibrotic effect. In this study, an in vitro model of skin fibrosis was established using human keratinocyte (HaCaT) cells treated with 5 ng mL−1 transforming growth factor beta (TGF-β) for 24 h. The results showed that TCC significantly inhibited EMT progression by reducing α-smooth muscle actin (α-SMA) levels and increasing E-cadherin level. Compared to tFNA or Cel alone, TCC exhibited superior anti-fibrotic effects in the fibrosis model, as evidenced by modulation of SMAD family member 2 (SMAD2) signaling and collagen I expression. Furthermore, the TCC group showed lower levels of nuclear factor κB p65 (NF-κB p65), BCL-2-associated X protein (Bax), and reactive oxygen species (ROS) compared to the Cel or tFNA groups. These findings highlight TCC as a promising treatment for skin fibrosis, with its synergistic anti-fibrotic effects providing new therapeutic avenues.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3736-8
Covalent organic frameworks (COFs) are porous crystalline materials assembled from organic building blocks via strong covalent bonds, offering well-defined pores, high surface area, and tunable properties for applications in gas storage, separation, catalysis, sensing, and energy conversion. However, conventional solvothermal synthesis requires high temperatures, long reaction times, and complex procedures, hindering scalability and increasing costs. Additionally, COFs are typically obtained as microcrystalline powders, limiting their direct use in flow processes. To overcome these barriers, a novel solid-state hot-pressing method was recently reported, enabling rapid synthesis of COF platelets with high crystallinity and porosity. This method involves applying pressure and heat simultaneously, reducing the energy barrier for monomer reactions and facilitating layer growth and stacking, as confirmed by density functional theory and molecular dynamics simulations. The approach demonstrated versatility by synthesizing 15 distinct COFs, including imine-, hydrazone-, β-ketoenamine-, and imide-linked frameworks, a three-dimensional COF (COF-300), and a mixed-monomer COF, all within 0.5–5 minutes. Notably, a free-standing COF platelet of 200 cm² was fabricated, showcasing scalability. This strategy addresses the trade-offs among synthetic convenience, product quality, environmental impact, and scalability, positioning COFs for commercial viability.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506031
The production of activated carbon from waste biomass such as cyanobacteria from Lake Taihu represents a promising resource utilization route. However, existing studies are mostly confined to laboratory scale, and the gap between laboratory processes and industrial production hinders the evaluation of technical feasibility and economic viability. This study optimized the process for producing cyanobacteria-based columnar activated carbon by co-processing cyanobacteria with garden waste (sawdust), and validated the process on an engineering-scale production line with a daily capacity of 5 t of raw materials. Economic feasibility was also assessed. Results showed that the optimized activated carbon exhibited a particle strength of 91.3% and a specific surface area of 571.44 m2·g−1. The engineering-scale line processed 5 t of raw materials daily, yielding approximately 1.18 t of activated carbon with stable quality: strength of 94.3% and specific surface area of 471.42 m2·g−1, featuring a microporous-dominant structure with coexisting micropores and mesopores. Cost analysis indicated a production cost of 3,595.65 CNY per ton of activated carbon, demonstrating favorable economic benefits. This work provides a basis for larger-scale production and application of cyanobacteria-based activated carbon.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0020
Ammonia borane (AB) is a promising hydrogen storage material due to its low molecular weight and high hydrogen content. The development of low-cost, high-activity catalysts for AB hydrolysis is critical for industrialization. In this work, CuO nanosheets (CuO NS) were synthesized via a solvothermal method under alkaline conditions using anhydrous copper chloride as precursor. Subsequently, low-temperature phosphating converted CuO NS into Cu3P@CuO nanosheets (Cu3P@CuO NS). The morphology and structure were characterized by SEM, TEM, AFM, XRD, and XPS. The catalytic performance for AB hydrolysis was evaluated, revealing that at a phosphating ratio of m(CuO NS)/m(NaH2PO2)=1 (0.1 g each), Cu3P@CuO NS exhibited excellent activity with a TOF of 57.23 min−1 and an apparent activation energy of 44.31 kJ/mol. The reaction followed pseudo-first-order kinetics with respect to catalyst amount and pseudo-zero-order kinetics with respect to AB concentration. The superior performance is attributed to the abundant active sites exposed by the nanosheet structure. Given the extremely low cost, Cu3P@CuO NS is a promising alternative to noble metal catalysts for hydrogen generation from AB.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507057
This study presents a novel electrochemical sensor for the rapid detection of trace lead ions (Pb(II)) in water, utilizing a rod-shaped bismuth-based electrode. The electrode was fabricated by modifying a glassy carbon electrode (GCE) with basic bismuth nitrate [Bi6O5(OH)3](NO3)5·3H2O, synthesized via a chemical precipitation method. The sensor was characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), electron probe microanalysis (EPMA), and energy-dispersive X-ray spectroscopy (EDS), confirming the rod-like morphology and composition. Electrochemical detection was performed using differential pulse voltammetry (DPV) in a 0.1 mol·L−1 NaAc-HAc buffer (pH 4.3). The sensor exhibited a linear detection range for Pb(II) from 1 to 90 μg·L−1, with a detection limit of 0.34 μg·L−1 and a sensitivity of 106 μA·(μmol·L−1)−1. The electrode demonstrated excellent anti-interference capability and reproducibility. Recovery tests in real water samples (tap water and campus lake water) yielded high recovery rates, indicating practical applicability. This work provides a simple, cost-effective, and reliable method for monitoring trace Pb(II) in environmental water, particularly relevant for public swimming pools and similar aquatic facilities.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0027
Electrocatalytic CO2 reduction reaction (CO2RR) offers a promising route to mitigate CO2 emissions while producing valuable chemicals. This study reports a Cu-Sn alloy catalyst with a wheat-ear-like dendritic structure, fabricated via a one-step electrodeposition method, for selective CO2 electroreduction to formate. Compared to pure Cu and Sn electrodes, the Cu-Sn alloy exhibits superior catalytic activity and selectivity toward formate, achieving a maximum Faradaic efficiency (FE) of 80% and maintaining above 70% FE over a potential window from -1.7 V to -2.0 V (vs. Ag/AgCl). The enhanced performance is attributed to the unique dendritic morphology that provides abundant active sites and the synergistic alloying effect that modulates the adsorption of the CO2*- intermediate, as corroborated by electrochemical measurements and X-ray photoelectron spectroscopy (XPS). This work presents a facile strategy for designing bimetallic catalysts for efficient CO2RR to formate.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025121602
This study characterized the body burden of polybrominated diphenyl ethers (PBDEs) in a physical examination population in Shenzhen and evaluated its impact on thyroid function. Serum samples from 368 residents were analyzed for eight PBDE congeners using atmospheric pressure gas chromatography-tandem mass spectrometry (APGC-MS/MS). The median concentration of ∑8PBDEs was 10.2 ng·g⁻¹ lipid weight (lw), ranging from 0.13 to 2089.4 ng·g⁻¹ lw, with BDE-209 predominating (59.7% of total). Multiple linear regression revealed that a 1.7-fold increase in serum BDE-153 was associated with a 0.4% increase in free triiodothyronine (FT3) (P<0.05), while a 1.7-fold increase in BDE-183 was associated with a 0.9% decrease in total triiodothyronine (T3) and a 0.7% decrease in FT3 (P<0.05). Bayesian kernel machine regression (BKMR) indicated a negative correlation between mixed PBDE exposure and thyroid-stimulating hormone (TSH) at high exposure levels. Weighted quantile sum (WQS) regression showed that mixed exposure was associated with decreased T3 levels and T3/FT3 ratio, with BDE-153 and BDE-183 as the primary contributors. These findings suggest that PBDE exposure may adversely affect thyroid function and disrupt thyroid hormone homeostasis, with BDE-183 and BDE-153 playing key roles. This study provides a scientific basis for PBDE health risk assessment and thyroid protection.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024092906
Microplastic pollution in rivers and lakes has become a research hotspot, yet studies in Anhui Province have predominantly focused on northern and central regions, leaving southern Anhui under-investigated. This study addresses that gap by examining the Xin'an River in Huangshan City, a typical river in southern Anhui. Surface water and sediment samples were collected in December 2023. In surface water, microplastic concentrations ranged from 350 to 3700 n·m−3, with particles of 0–0.5 mm dominating (33.93%). Fibrous shapes were most prevalent (59.83%), and colored particles accounted for 50.27%. In sediments, concentrations ranged from 25 to 200 n·kg−1, with 0–0.5 mm particles again dominant (49.63%). Fibers comprised 47.08% of sediment microplastics, and white particles accounted for 34.74%. Polymer analysis identified polyethylene terephthalate (PET) as the most abundant material (36.61%), followed by polyamide (PA) (23.22%). Source analysis suggests that fibrous microplastics originate primarily from fiber-based products such as clothing, home textiles, and fishing nets. These findings provide essential baseline data for water resource management, pollution assessment, and ecological remediation of the Xin'an River.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024122101
Bicarbonate and carbonate ions (HCO3−/CO3^2−) are ubiquitous in wastewater and readily scavenge strong oxidants, leading to the formation of carbonate radicals (CO3·−) in radical-based advanced oxidation processes. This study investigated the influence of HCO3−/CO3^2− on the degradation kinetics of sulfamethazine (SMR) in a UV/TiO2 system. The presence of HCO3−/CO3^2− enhanced the degradation rate of SMR by sixfold compared to UV/TiO2 alone. Radical quenching experiments identified CO3·− as the primary reactive species responsible for the enhanced degradation, with hydroxyl radicals (·OH) also contributing. To quantitatively delineate the roles of reactive species and account for water matrix effects, a kinetic model was constructed using Kintecus software. The model accurately predicted SMR degradation over time and the contributions of individual radicals, demonstrating good predictive capability. Application of the model to real wastewater predicted that CO3·− is the dominant radical responsible for SMR degradation. These findings highlight the critical role of carbonate radicals in UV/TiO2 processes and provide a robust modeling framework for predicting the fate of pharmaceuticals in carbonate-rich waters.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604010
Guar gum production wastewater contains 1,2-propanediol, which in conventional anaerobic treatment causes propionate accumulation and microbial inhibition. Microaerobic conditions foster fermentative bacterial metabolism, enhancing organic substrate conversion, while biochar promotes anaerobic microbial aggregation and oxygen tolerance. This study treated actual guar gum wastewater using three configurations: blank control, anaerobic, and microaerobic-biochar (O2/BC) coupled systems. Under mesophilic conditions (37 °C), with micro-aeration at 0.2 mL/(g VS·d) and biochar dosage of 15 g/L, the O2/BC system achieved a COD removal efficiency of 90%, 10.6 percentage points higher than the anaerobic control. Effluent COD and propionate concentrations dropped to 3800 mg/L and 0.15 g/L, respectively, representing reductions of 49.6% and 98.4% versus the control. Biogas production was 1.64 times that of the control, with a maximum methane concentration of 77.2%. Fourier transform infrared spectroscopy (FT-IR) indicated increased abundance of –OH, –CH2–, and C–O functional groups on sludge surfaces, revealing biochar's adsorption enhancement. Scanning electron microscopy (SEM) showed dense microbial aggregates dominated by long bacilli, distinct from conventional anaerobic sludge. Microbial community analysis revealed increased abundance of Clostridium and Comamonas, modulating the propionate-to-acetate ratio and optimizing acidification efficiency, thereby promoting complex organic degradation. This study provides a novel technical pathway for biological treatment of alcohol-rich organic wastewater.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604002
A robust analytical method was developed for the simultaneous determination of 22 per- and polyfluoroalkyl substances (PFAS) in surface water using ultra-high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS). To address the loss of particle-bound PFAS, the method incorporates a methanol extraction step for particulate matter retained on filters, followed by combining the extract with the filtrate. Samples were then concentrated and purified using weak anion exchange (WAX) solid-phase extraction (SPE) cartridges. After nitrogen evaporation, the residue was reconstituted in methanol/water (8:2, v/v) and filtered prior to analysis. Quantification was performed using isotope dilution. The method exhibited excellent linearity (R² > 0.995) over a concentration range of 1–250 µg/L. Method detection limits ranged from 0.2 to 0.6 ng/L, and method quantification limits from 0.8 to 2.4 ng/L. Recoveries in blank water and surface water matrices were 85.3%–139% and 76.4%–127%, respectively, with relative standard deviations (RSD, n=6) below 15%. Compared to conventional methods without particulate extraction, this approach significantly improved recovery rates in surface water, effectively eliminating negative bias caused by particle adsorption. The method is sensitive, accurate, and reliable, making it suitable for routine monitoring of PFAS in surface water.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3451-2
Visual aesthetics is a key metric of semi-transparent organic photovoltaics (ST-OPVs) for building-integrated solar windows, yet previous studies have primarily focused on the compromise between efficiency and transparency. This work addresses the overlooked aspect of full visual aesthetic control, particularly the bidirectional reflected color for architectural harmony, via designing ST-OPVs with double-sided ultra-thin Ag/TeO2 transparent electrodes. This design facilitates full-spectrum color tunability covering the whole standard color gamut of CIE coordinates on both surfaces, achieved simply by adjusting layer thicknesses. The resulting devices exhibit neutral transparency (16.6%–27.0% average visible transmittance) and competitive power conversion efficiencies (8.1%–9.2%). Additionally, the devices demonstrate strong flexibility, with flexibility-adaptive coloration and curvature-enhanced aesthetics. This work presents an ST-OPV design featuring full visual aesthetics and considerable performance, paving the way for commercialization of organic solar windows for building and vehicle integration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3930-3
Methylammonium lead tribromide (MAPbBr3) single crystals (SCs) are promising for room-temperature gamma-ray and X-ray detection, but scaling their size often compromises crystal quality. Here, we report a strategic precursor stoichiometry engineering approach to grow inch-sized, high-quality MAPbBr3 SCs via a constant-temperature evaporation method. We show that constructing a robust electrical double layer through organic cation modulation effectively stabilizes the colloidal precursor. This is achieved by synergistically suppressing MA+ deprotonation while promoting MA+ adsorption as counterions on the [PbBrn]2−n complexes, which collectively strengthens interparticle repulsion and raises the nucleation barrier. This multifaceted approach yields MAPbBr3 SCs with lateral dimensions up to 2 inches and an exceptional X-ray diffraction rocking curve full width at half maximum (FWHM) of 0.0093° at the (002) face. Consequently, the SCs enable spectroscopic-grade gamma-ray detection, achieving energy resolutions (ER) of 8.4% for the 57Co source (122 keV) and 11.1% for the 137Cs source (662 keV), along with a high X-ray sensitivity of 1.65 × 10^4 μC Gy−1 cm−2. This work paves the way for the practical application of MAPbBr3 SCs in high-performance gamma-ray and X-ray detection.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4094-8
Deep-blue multi-resonance thermally activated delayed fluorescence (MR-TADF) emitters with high efficiency, high color purity, and high brightness are critically important for next-generation OLED displays, yet remain challenging due to severe aggregation and host-guest interactions in the solid state. Herein, we report a core-encapsulating molecular design strategy in which bulky and non-conjugated peripheral groups are introduced to sterically encapsulate a blue-emitting MR core, thereby suppressing intermolecular π-π interactions without perturbing its intrinsic electronic structure. Two new emitters, DNa-BN and QNa-BN, featuring half-encapsulated and fully encapsulated MR-core architectures, respectively, were developed. Owing to its fully encapsulated structure, QNa-BN exhibits pronounced aggregation resistance at high doping concentrations, maintaining photoluminescence quantum yields exceeding 96%, radiative decay rate constants on the order of 10^8 s−1, and fast reverse intersystem crossing rates (~10^5 s−1). Consequently, sensitizer-free OLEDs based on QNa-BN deliver narrowband deep-blue emission at 458 nm with a full width at half maximum of 22 nm, CIE coordinates of (0.142, 0.085), a maximum external quantum efficiency (EQE_max) of 34.4%, and a maximum luminance exceeding 20,000 cd m−2. Furthermore, by adopting a hyperfluorescence architecture, the EQE_max is further boosted to 38.7% with significantly suppressed efficiency roll-off. This work demonstrates that steric encapsulation of the MR core provides an effective and general approach to achieving aggregation-resistant, high-efficiency, and high-brightness deep-blue MR-TADF emitters for OLED applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3595-7
Cu(I) complexes exhibiting thermally activated delayed fluorescence (TADF) have emerged as promising alternatives to noble-metal-based emitters for organic light-emitting diodes (OLEDs). However, the development of red-emitting Cu(I) complexes has been hindered by slow radiative decay and fast nonradiative decay. In this study, a linear two-coordinate Cu(I) complex, ICuTMC, was designed and synthesized. By pairing a pyrazine-fused N-heterocyclic carbene and a tetra-methylcarbazolyl ligand, a strong ligand-to-ligand charge transfer excited state is generated. Single-crystal structure authenticates close intramolecular C–H···Cu contacts, providing good steric shielding to the metal center. C–H···π interactions between ligands are also revealed. The complex exhibits highly efficient red TADF with emission maximum at 622 nm, photoluminescence quantum yield of 76%, and short delayed fluorescence lifetime of 0.24 μs. This is enabled by a large oscillator strength from the coplanar donor-Cu-acceptor conformation, a small singlet-triplet energy gap from spatial separation of frontier molecular orbitals, and strong spin-orbit coupling from the metal center. Vacuum-deposited OLEDs based on ICuTMC achieve a peak external quantum efficiency of 25.9% and a significantly small roll-off of 1.9% at 10,000 cd m−2. These performances demonstrate a way to overcome the energy gap law for linear coinage metal complexes toward red OLEDs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3745-1
Short-wavelength infrared (SWIR) organic photodetectors (OPDs) have attracted considerable attention due to their potential to overcome the limitations of inorganic counterparts. However, developing organic semiconductors with strong SWIR detection remains a significant challenge. Herein, we design and synthesize a new conjugated pyrrolic polysquaraine (PSQ-COT) by integrating a pyrrolic squaraine unit with a strong electron-donating moiety, achieving an absorption onset extending to 1.2 μm. To evaluate its detection performance, we fabricated two types of PSQ-COT-based SWIR OPDs with PC61BM and BTP-eC9 as the electron acceptors, respectively. The resulting PSQ-COT:PC61BM OPD exhibited superior detection performance compared with the BTP-eC9 counterpart, achieving an impressive specific detectivity of 1.08 × 10^12 Jones at 1030 nm under zero bias. This enhanced performance is due to the lower degree of energetic disorder and reduced trap density in the PSQ-COT:PC61BM device. Furthermore, we successfully integrated the PSQ-COT:PC61BM OPD into a high-pixel-density image array (640 × 512 pixels), enabling clear matter identification under SWIR light irradiation. This work provides valuable insights into designing high-performance organic semiconductors for SWIR light detection and imaging applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3891-5
Alloys with low thermal expansion are vital for precision components in aerospace, cryogenics, optics, and electronics, where dimensional stability under thermal cycling is essential. As these applications face harsher mechanical and thermal conditions, materials must offer not only low thermal expansion but also high strength and ductility. Achieving all three remains difficult, as their underlying microstructural requirements often conflict. Here, we present a medium-entropy alloy, Fe54Ni34Co6Ti3Al3 (at.%), designed to overcome this challenge through tailored precipitation engineering. The alloy forms coherent L12 nanoprecipitates that not only provide substantial precipitation strengthening but also modulate the composition of the face-centered cubic matrix. This tuning induces a low coefficient of thermal expansion and metastability in the matrix, enabling transformation-induced plasticity that enhances ductility and strain hardening. As a result, the alloy achieves a tensile yield strength of (1036±21) MPa, uniform elongation of 18.4%±1.1%, and a coefficient of thermal expansion of 5.8×10−6 °C−1. This work demonstrates a precipitation-driven pathway to reconcile strength, ductility, and thermal stability, offering a new strategy for designing multifunctional structural materials for advanced engineering environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4054-x
The sluggish kinetics and high onset potentials of the oxygen evolution reaction (OER) at the anode of alkaline water/seawater electrolyzers limit overall energy efficiency. Noble-metal oxides like RuO2 are active but suffer from high cost, agglomeration, and dissolution under oxidizing potentials, especially in chloride-rich electrolytes where competing chloride oxidation reaction (ClOR) occurs. Here, we report a mild two-step dry-wet milling strategy to achieve throughout lattice doping of F− into MnO2 (F-MnO2) and subsequent anchoring of atomically dispersed Ru via Ru–O/F hybrid bonds. The strengthened Mn 3d–O/F 2p hybridization and negative charge shielding of surface F− enhance OER activity/selectivity relative to ClOR and impart superior Cl− tolerance and corrosion resistance. The resulting F-Ru-MnO2-TH electrocatalyst exhibits overpotentials of 280 mV and 200 mV at 10 mA cm−2 in alkaline water and simulated seawater, respectively. It retains ~100% of initial activity after 200 h continuous operation in alkaline media and >95% after 300 h in simulated seawater, significantly outperforming Ru-MnO2 and commercial RuO2. This work provides a scalable route to durable, high-performance OER catalysts for seawater electrolysis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3464-4
Photocatalytic conversion of atmospheric CO2 (0.03%) into multi-carbon fuels remains a grand challenge due to the high energy barrier of C–C coupling and the low concentration of CO2. Here, we report the construction of multiple metal pair sites on metal oxide nanosheets to steer C–C coupling, enabling efficient photoreduction of air-concentration CO2 to ethane (C2H6). As a prototype, Au nanoparticles were anchored on Bi4Ti3O12 nanosheets (Au-Bi4Ti3O12). High-resolution transmission electron microscopy and X-ray photoelectron spectroscopy confirmed the formation of Au-Ti metal pair sites at the interface. In situ Fourier transform infrared spectroscopy revealed the presence of *OCCOH intermediate on Au-Bi4Ti3O12 during CO2 photoreduction, which was absent on pristine Bi4Ti3O12. Density functional theory calculations showed that the Gibbs free energy for *CO–COH formation on Au-Bi4Ti3O12 is 2.23 eV, significantly lower than that on Bi4Ti3O12 (3.59 eV), indicating facilitated C–C coupling. Consequently, Au-Bi4Ti3O12 exhibited a C2H6 evolution rate of 2.58 μmol g−1 h−1 under 0.03% CO2, whereas Bi4Ti3O12 produced only C1 products (CO and CH4). This work demonstrates the first single-catalyst photoreduction of atmospheric CO2 to C2H6, highlighting the effectiveness of engineered multiple active sites in overcoming the C–C coupling bottleneck.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3782-0
Oral mucositis (OM) is a debilitating complication of cancer therapy, characterized by severe pain, mucosal barrier breakdown, and infection risk. Current hydrogel-based topical systems suffer from poor transmucosal permeation and lack of inflammatory microenvironment-triggered drug release. Here, we report a supramolecular strategy for designing guanosine-fibril hydrogels and derived microneedle patches. Tavaborole (Ta), crisaborole (Cr), and strontium (Sr2+) ions serve dual roles as structural building blocks and biofunctional agents. Unlike conventional G4·K+ fibrils, the unique G4·Sr2+-Ta/Cr fibrils incorporate Ta/Cr via boronic ester bonds on guanosine and Sr2+ through G-quartet cation recognition. This design mechanically reinforces the hydrogel through additional hydrophobic interactions and ion-pair recognition, while synergistically providing antimicrobial/anti-inflammatory effects (Ta/Cr), pro-angiogenic activity (Sr2+), and reactive oxygen species (ROS) scavenging (guanosine). The optimized gelation process enables fabrication of microneedle patches with pseudomembrane-penetrating capability and ROS-triggered drug release via boronic ester hydrolysis. In vivo mouse experiments confirm efficacy in controlling OM-associated inflammation, modulating oral microbiota homeostasis, and promoting angiogenesis at ulcer sites. This work demonstrates multifunctional integration via hierarchical structural design, extending guanosine supramolecular assemblies into bioactive platforms for OM treatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3634-0
Messenger RNA-lipid nanoparticle (mRNA-LNP) vaccines have demonstrated extraordinary efficacy against severe acute respiratory syndrome coronavirus 2, establishing LNPs as the premier platform for mRNA therapeutics. However, the pervasive presence of anti-polyethylene glycol (PEG) antibodies undermines PEGylated LNP performance by diminishing therapeutic efficacy. To address this challenge, we synthesized a panel of lipid-poly(2-oxazoline) (lipid-POx) conjugates as alternatives to lipid-PEG and systematically evaluated how their polymer backbone, degree of polymerization, and lipid tail structure influence LNP physicochemical properties and mRNA delivery performance. Among POx-LNPs formulated with heptadecan-9-yl 8-((2-hydroxyethyl)(6-oxo-6-(undecyloxy)hexyl)amino)octanoate (SM-102) as the base lipid, those constructed with single-tailed C18-POx exhibited smaller particle sizes and superior freeze-thaw stability. These C18-POx-LNPs maintained comparable in vivo transfection efficiency to PEG-LNPs even when fully replacing 1,2-dimyristoyl-sn-glycero-3 (DMG)-PEG. Notably, in mice bearing pre-existing anti-PEG antibodies, C18-POx-LNPs demonstrated over 200-fold higher transfection efficiency than PEG-LNPs. Additionally, repeated administration of POx-LNPs induced dose-dependent anti-POx immunoglobulin M (IgM) and IgG responses, with antibody titers inversely correlated with POx hydrophilicity. This study underscores the effectiveness of substituting PEG with POx in LNP construction to address the transfection efficiency in populations with pre-existing anti-PEG antibodies, and would inspire the development of more hydrophilic polymers for LNP formulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3633-5
High-temperature interfacial diffusion in Half-Heusler (HH) thermoelectric devices poses significant challenges for practical applications, particularly the diffusion of Ag from conventional solders, which degrades material performance and device stability. This study reveals anomalous Ag diffusion through a Cr powder barrier layer into Ti0.5Zr0.5NiSn0.98Sb0.02, driven by Sn phase penetration. In contrast, employing a Cr foil barrier layer pre-densified the material, effectively preventing Sn phase penetration and eliminating Ag diffusion pathways, thereby preserving junction integrity. After aging at 973 K for 30 days, the Cr foil junction maintained a clean interface with a low contact resistivity of 0.27 μΩ cm2. Benefiting from this interfacial design, a Hf-free HH module achieved a high conversion efficiency of 10.4% at a hot-side temperature of 976 K, alongside long-term stability. This work addresses critical bottlenecks in developing high-performance, low-cost HH modules, facilitating their commercial application in waste heat recovery.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3545-7
Magnetically driven hydrogel robots show promise in biomedical and underwater applications due to remote controllability, flexibility, biocompatibility, and chemical stability. However, limited functional integration restricts their adaptability. Here, a universal modular assembly strategy is introduced using a self-healing κ-carrageenan/polyacrylamide hydrogel embedded with magnetic particles, enabling free assembly of magnetic actuation modules. These modules construct soft robots with complex geometries and magnetization distributions, allowing diverse deformations under magnetic fields. The strategy further integrates photocatalysis by embedding Ru-Bi2CrO6 photocatalysts into functional modules, yielding an oxygen-generating robot. This robot exhibits flexible underwater movement via magnetically controlled oscillatory actuation, minimizing water agitation while supplying stable oxygen to specific aquatic environments. The photocatalytic oxygen evolution rate reaches 389.1 μmol g−1 h−1. The hydrogel skeleton suppresses particle aggregation and sedimentation, and facilitates magnetic recovery. This scalable and adaptable approach advances multifunctional soft robot design.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61100-6
Sodium-ion capacitors (SICs) are attractive for low-cost and safe energy storage, but their practical development is limited by sluggish Na+ storage kinetics and structural instability of anodes. Control of both bulk structure and surface chemistry can address these limitations. We report a heteroatom-rich porous carbon (HRPC) derived from spores via hydrothermal pretreatment, low-temperature carbonization, and acid-mediated functionalization. The optimized GLSHC-HNO3 anode exhibits hierarchical porosity and multi-element co-doping, enabling rapid ion/electron transport, improved electrolyte wettability, and abundant Na+ adsorption sites. Density functional theory calculations reveal distinct contributions of different heteroatom configurations to sodium adsorption. The HRPC anode delivers an ultrahigh reversible capacity of 446.1 mAh g−1 at 50 mA g−1, retains 237.3 mAh g−1 at 2 A g−1, and shows excellent cycling stability. A full SIC with a polyaniline-derived porous carbon cathode achieves an energy density of 114.4 Wh kg−1 at 290 W kg−1, 43.1 Wh kg−1 at 1450 W kg−1, and a maximum power density of 5800 W kg−1, with 84.3% capacity retention after 5000 cycles and nearly 100% Coulombic efficiency. This work establishes a scalable, sustainable route for converting biomass into high-value carbon anodes, providing a new pathway for high-performance sodium-ion energy storage.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61108-0
Adipic acid is a key monomer for nylon-6,6 and nylon-6, yet its industrial production via nitric acid oxidation of KA oil suffers from high energy consumption and N2O emissions. This study reports a green catalytic system for one-pot oxidation of cyclohexane to adipic acid using a Cu/Cu2O@C composite catalyst derived from wood chips. During pyrolysis, wood chips serve as both carbon support precursor and in-situ reducing agent, converting Cu2+ into Cu/Cu2O active species. The abundant defects in biomass carbon form strong coordination interactions with copper, regulating the electronic distribution of active sites and enhancing catalytic performance. Under optimized conditions (100 °C, 12 h), the Cu/[email protected] catalyst achieves a cyclohexane conversion of 19.36% and an adipic acid selectivity of 73.28%. Mechanistic studies reveal that the electronic interaction between the carbon support and copper species strengthens adsorption of cyclohexanone, promoting selective formation of adipic acid. The reaction follows a free radical chain mechanism involving hydroxyl and alkyl radicals. This work provides a viable strategy for developing eco-friendly, low-cost, and high-efficiency catalytic materials for industrial adipic acid synthesis.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61102-X
Silicon-carbon composites prepared by chemical vapor deposition (CVD) are promising anode materials for high-energy-density lithium-ion batteries. However, the influence of the pore structure of the porous carbon (PC) carrier on silicon deposition behavior, and the impact of surface silicon on cycling stability, remain unclear. This study systematically investigates these effects using nitrogen adsorption-desorption analysis, X-ray photoelectron spectroscopy, and thermogravimetric analysis. Porous carbons with varying pore architectures were synthesized by adjusting KOH activator ratios. Results show that increased micropore volume facilitates higher silicon mass loading, but also elevates the content of surface floating silicon due to greater silane exposure. Moderately increasing mesopores in high-microporosity carbon promotes deeper silicon deposition, reducing surface floating silicon. Excessive surface floating silicon hinders lithium-ion diffusion kinetics, leading to accumulation of active lithium, accelerated SEI growth, and electrode degradation. Electrochemical testing reveals that the optimized silicon-carbon composite maintains a high specific capacity of 693.1 mAh/g after 150 cycles at 0.5 C (900 mA/g). This work provides new insights into the development and failure mechanisms of CVD-derived silicon-carbon composite anodes, emphasizing the critical role of pore structure in mitigating surface silicon and enhancing cycling stability.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507058
With the rapid development of China's lithium-ion power battery industry, the recycling of large-scale retired batteries has become a critical link for the sustainable development of the new energy vehicle industry. The recovery of cathode materials from spent lithium iron phosphate (LiFePO4) batteries is a current research hotspot, significant for resource recycling and environmental protection. This study systematically reviews recent progress in recycling technologies for spent LiFePO4 cathode materials, mainly including direct regeneration, pyrometallurgy, and hydrometallurgy. It focuses on analyzing the current research status of key steps in hydrometallurgy, such as leaching of valuable elements, deep removal of impurities, and product regeneration, and compares the advantages and limitations of various methods. Addressing core issues in current recovery processes, such as insufficient high-value utilization of iron and phosphorus resources and difficulty in deep impurity removal, this study proposes corresponding solutions and technical prospects, aiming to provide theoretical reference and engineering guidance for efficient, clean, and high-value recycling of spent LiFePO4 batteries.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508013
The Sanshenggong section of the Yellow River is a critical hydrological monitoring and control point, whose water quality directly affects the ecological safety and sustainable water resource utilization of the middle and lower reaches. This study analyzed water quality monitoring data from 2011 to 2024 using the Mann-Kendall test to identify abrupt change years, combined with single-factor evaluation and a fuzzy comprehensive evaluation method improved by CRITIC-entropy weight combination to systematically assess water quality evolution. The Mann-Kendall test identified 2013 and 2019 as abrupt change points, with non-significant improvement from 2013 to 2015 and significant improvement after 2016. Single-factor evaluation indicated that total phosphorus (TP) was the primary exceeding factor in 2011–2012, and its declining concentration drove the water quality upgrade from Class III to Class II in 2013. The CRITIC-entropy weight combination assigned the highest weight (28.96%) to permanganate index, whose decline was the core driver of water quality improvement. The improved fuzzy evaluation showed that the membership degree of Class III water dropped to zero in 2013, indicating stable improvement, but periodic rebounds in Class II membership suggested potential degradation risks. This study provides scientific evidence for ecological protection and high-quality development of the Yellow River Basin.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510028
This study investigates the aging mechanism of polystyrene microplastics (PS MPs) induced by ultraviolet (UV)-activated potassium persulfate (KPS) and its influence on the adsorption of norfloxacin (NOR). Results show that aged PS exhibited yellowing, increased surface roughness and specific surface area, enhanced oxygen-containing functional groups, and elevated negative surface charge, along with the generation of environmentally persistent free radicals (EPFRs). Compared with UV alone, UV+KPS induced more pronounced aging due to the generation of reactive oxygen species (ROS) including hydroxyl radicals (·OH) and superoxide radicals (O2·−). Adsorption kinetics and isotherm data revealed that UV+KPS-aged PS significantly enhanced NOR adsorption, with a maximum adsorption capacity of (2.539±0.032) mg·g−1, which was 4.20 times higher than that of pristine PS. The adsorption mechanism was governed by hydrogen bonding, electrostatic interactions, and pore filling. Solution pH modulated the electrostatic interactions by affecting NOR speciation and PS surface charge, thereby influencing NOR adsorption. This study systematically reveals the accelerated aging of coexisting MPs and EPFRs generation during UV+KPS treatment, contributing to a comprehensive understanding of MPs environmental behavior and potential ecological risks.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010604
Groundwater is a vital component of Beijing's water supply, yet elevated sulfide concentrations restrict its utilization. This study employed principal component analysis (PCA) and absolute principal component-multiple linear regression (APCS-MLR) to apportion sulfide sources and quantify their contributions in the middle and lower reaches of the Chaobai-Wenyu alluvial-proluvial fan. Sulfur and oxygen isotopes (δ34S and δ18O) were used to identify sulfate sources and discern anthropogenic versus natural influences. Results showed that high-sulfide groundwater predominantly occurred in Na-type water, with sulfide accumulation from desulphidation widespread, particularly in Shunyi and within the first, second, and third aquifers, independent of wet/dry seasons. Isotopic analysis indicated sulfate mainly originated from evaporite dissolution, and sulfides from desulphidation were of geological background origin. PCA extracted four principal components: leaching-enrichment (F1), natural dissolution of iron-manganese oxides (F2), water desulphidation (F3), and CaF2 dissolution equilibrium (F4). F3 exhibited the highest factor loading for sulfide (0.418), while other components had small negative loadings. APCS-MLR revealed F3 contributed 21.32% of sulfide, while indigenous sources (e.g., acid-volatile sulfide dissolution, elemental sulfur disproportionation, geothermal activity, well casing materials) contributed 63.66%. Overall, sulfide in the study area is a geological background factor, with limited anthropogenic influence.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025011302
Heavy metal contamination in soil severely compromises the quality and safety of Alisma orientale medicinal materials, and consumption of contaminated herbal preparations poses health risks. To characterize contamination and risks in Sichuan's genuine producing areas, 159 paired soil and plant samples were collected. Concentrations of Cu, Zn, Pb, Cd, and Ni were determined via ICP-OES. Soil pollution was assessed using the Single Pollution Index (Pi), Nemerow Comprehensive Index (Pn), and Potential Ecological Risk Index (RI). Human health risks from heavy metals in Alisma were evaluated via Target Hazard Quotient (THQ) and Hazard Index (HI). Mean soil concentrations were Cu 29.57, Zn 61.86, Pb 29.51, Cd 1.77, and Ni 28.08 mg·kg−1. Except for Cd, all elements were below agricultural soil screening values. Pi and Pn confirmed Cd contamination, with Cd posing slight to strong potential ecological risks. Cu, Cd, Pb, and Ni showed highly significant positive correlations, indicating common origins. Heavy metal concentrations in Alisma did not exceed pharmacopeial limits. The plant exhibited strong Zn enrichment but weak accumulation of Cu, Cd, and Pb, and negligible Ni enrichment. THQ and HI values indicated no potential health risks under current exposure. Quantitative assessment is critical for soil pollution control, safe cultivation, and medication safety.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025011303
Polybrominated diphenyl ethers (PBDEs) are persistent organic pollutants with environmental persistence, bioaccumulation, and toxicity, posing significant threats to marine ecosystems and human health. This study developed an analytical method using anhydrous sodium sulfate-alumina composite column chromatography coupled with gas chromatography-orbitrap mass spectrometry to quantify mono- to deca-BDEs in coastal seawater of Dalian, China. The total PBDE concentrations (∑PBDEs) ranged from not detected to 511.96 pg·L−1, with a mean of 163.96 pg·L−1. BDE-209 was the dominant congener, contributing 24.1% to ∑PBDEs. Spatial distribution exhibited distinct heterogeneity, with higher abundances of highly brominated PBDEs near sewage discharge outlets. Partial least squares discriminant analysis indicated that anthropogenic activities, particularly sewage discharge, were the primary sources. Ecological risk assessment revealed extremely low risk, with the highest risk quotient of 0.013 for BDE-17. These findings provide baseline data for PBDE contamination in Dalian coastal waters and underscore the need for continued monitoring of emerging contaminants.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025020603
The high cellulase-producing strains were screened and the enzyme production conditions were optimized, providing strain resources for the effective utilization of agricultural solid waste. A promising cellulolytic strain S3 was isolated from the soil of Hengshui Lake Wetland Park. The isolation process employed Congo red plate staining method for primary screening, followed by secondary screening through cellulase activity determination and straw degradation experiments. Through morphological observation and molecular biology identification, the strain S3 was identified to be Bacillus cereus. The ratio of transparent circle to colony diameter of strain S3 was 4.01±0.17. The filter paper enzyme activity of strain S3 was 42.09 U·mL−1, and the degradation rate of corn stover reached 19.29% after 10 days of fermentation. It was found that the optimum carbon source of strain S3 was the mixture of microcrystalline cellulose and wheat bran with the addition amount of 4%, and the optimum nitrogen source was soybean powder with the addition amount of 2%. Single factor experiment and response surface methodology were used to optimize the enzyme production conditions of the strain S3. The optimal conditions were fermentation time of 76 h, fermentation temperature of 36℃, initial pH of 6, and inoculation volume of 4%. Under these conditions, the filter paper enzyme activity reached 60.13 U·mL−1, which was 1.43 times higher than that before optimization. The strain S3 showed the high cellulase-producing capability, demonstrating its potential as an efficient microbial candidate for the degradation and utilization of agricultural solid waste.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605005
Water quality prediction is essential for river basin management, yet existing models often struggle with non-stationary, noisy monitoring data. This study collected water quality data from two city-level control sections in southern China from December 2020 to June 2024, including eight indicators: water temperature, turbidity, pH, conductivity, dissolved oxygen (DO), ammonia nitrogen (NH4+-N), total phosphorus (TP), and permanganate index (CODMn). To predict four key indicators (DO, NH4+-N, TP, CODMn), we developed hybrid models combining seasonal trend decomposition (STD), Bayesian hyperparameter optimization, and either random forest (RF) or XGBoost. STD smoothed and denoised the data while extracting seasonal factors; Bayesian optimization tuned model hyperparameters. Evaluation showed that the STD-Bayesian-XGBoost model achieved smaller bias errors and higher prediction accuracy than STD-Bayesian-RF. Specifically, XGBoost reduced root mean square error (RMSE) by 15-20% across all four indicators and improved the coefficient of determination (R²) to above 0.90, compared to RF's 0.85-0.88. The models were validated on southern river data, but the methodology is generalizable to other climatic and hydrological settings. This work provides a technical reference for pollution reduction and carbon management in regional watersheds.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605014
Chlorinated aliphatic hydrocarbons (CAHs) are prevalent groundwater contaminants at industrial sites in China. This pilot-scale study evaluated in-situ anaerobic bioremediation of CAHs-contaminated groundwater in a low-permeability bedrock fracture zone at depths up to 40 m. A self-developed anaerobic dechlorinating culture (BS-1), containing Dehalococcoides, Desulfitobacterium, and Dehalogenimonas, was injected alongside carbon sources (sodium citrate and emulsified vegetable oil) and nutrients. Pressurized nitrogen gas injection enhanced the distribution of amendments, achieving a radius of influence of 5.0 m. Over 399 days of monitoring, the combined use of slow-release and soluble carbon sources maintained anaerobic conditions (ORP < -100 mV) for over one year, providing sustained electron donors. The emulsified vegetable oil reduced injection frequency and operational costs. The BS-1 culture effectively dechlorinated vinyl chloride, cis-1,2-dichloroethylene, trichloroethylene, and chloroform, achieving removal efficiencies exceeding 95%. At times, groundwater quality met the Class IV standard of GB/T 14848-2017. This study demonstrates a green, economical, and effective solution for CAH-contaminated site remediation, with significant engineering application potential.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605019
The utilization of food waste as a fermentation substrate can effectively reduce the substrate cost of lactic acid production industrialization, and synergistic fermentation with leachate could promote lactic acid production. However, the effect of magnesium ions in leachate on lactic acid production, metabolic processes, and key functional bacterial communities remains unclear. This study investigated the effect of adding magnesium ions on lactic acid fermentation using food waste as substrate. Results showed that the optimal magnesium ion dosage was 750 mg/L, achieving a lactic acid yield of (37.4±0.5) g COD/L and L-lactic acid optical activity of (96.3±0.9)%. Mechanistic studies revealed that magnesium ions accelerated substrate dissolution, significantly enhanced the activities of key hydrolytic enzymes (α-glucosidase, amylase, protease) and L-lactic acid producing enzymes, thereby increasing hydrolysis and lactate production rates. Simultaneously, the relative activity of lactate-consuming enzymes decreased, slowing lactate consumption. At 750 mg/L Mg2+, the relative abundances of Enterococcus and Streptococcus were 65.0% (2.2 times the Blank) and 18.7% (37.8% of the Blank), respectively, with a total of 83.7%, enhancing lactic acid yield and L-lactic acid optical activity. Metabolic pathway prediction and functional gene analysis further indicated that magnesium ions increased the relative abundance of carbohydrate metabolism pathways and genes encoding lactate dehydrogenase. This study provides technical support for food waste resource utilization.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605021
The digestate from anaerobic digestion of food waste is separated into solid residue and liquid filtrate. The filtrate retains high nutrient and carbon content, making it a viable resource for recovery. This study prepared biochar from food waste digestate residue and employed it as an electrode active material in a flow-electrode capacitive deionization (FCDI) system, with activated carbon as a control, to assess nitrogen and phosphorus removal from kitchen waste biogas slurry. ZnCl₂ modification significantly enhanced the biochar's specific surface area, adsorption capacity, capacitance, and conductivity. The optimal mass fraction of modified biochar in the electrode liquid was 7.5%. In simulated digestate, the FCDI system achieved removal efficiencies of 47.7% for NH₄⁺-N and 55.2% for reactive phosphorus (RP) over 12 hours. Performance ranking of electrode materials was activated carbon > ZnCl₂-modified biochar > unmodified biochar. In continuous operation with actual anaerobic digestion filtrate, maximum removal efficiencies were 32.2% for NH₄⁺-N and 26.2% for RP. The reduced performance in real digestate is attributed to organic foulants such as peptides and amino acids, which block ion-exchange membrane channels, increase membrane resistance, and impede ion transfer and charge transport, thereby diminishing deionization efficiency.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605023
Identifying the characteristics of carbon emissions and driving forces of the railway sector is essential for formulating effective measures to develop a green and low-carbon railway industry. This study systematically evaluated the direct and indirect carbon emissions from 2016 to 2021 generated by the railway sector of China, and analyzed the spatiotemporal dynamic changes of the carbon emissions. On this basis, by adopting the LMDI model, the key factors affecting the carbon emissions of railway sector were discerned. Moreover, the variations in the dominant factors of the carbon emissions over time, and the spatial heterogeneities in the dominant factors of the carbon emissions of the 18 railway bureaus, were analyzed. The results show that: 1) During the periods from 2016 to 2021, the carbon emissions of China's railway sector showed an overall upward trend, increasing from 57.7486 million tons to 64.2084 million tons, by 11.2%. The Shanghai Bureau, Beijing Bureau, Zhengzhou Bureau, Chengdu Bureau and Guangzhou Bureau substantially contributed to the increases of railway carbon emissions. In spatial, the carbon emissions of the 18 railway bureaus were characterized by lower emissions in the west and higher emissions in the east, mainly due to the regional differences in the socio-economic development, industrial structure and population density; 2) During 2016 to 2021, the decline in energy consumption intensity reduced the carbon emissions of the railway sector by 18.8654 million tons, while the changes in carbon emission intensity, economic benefits of per unit passenger and freight turnover, and operating capacity led to an increase of a sum of 25.3252 million tons of carbon emissions. When decomposing the contributions of each factor by sub-periods, it can be found that the impacts of these factors on the carbon emissions changed over time. Only the factor of carbon emission intensity showed a promoting effect in all sub-periods, the other three factors, as energy consumption intensity, economic benefits of per unit passenger and freight turnover, and operating capacity, had a conversion between promoting and inhibiting effects. 3) The dominant factors of carbon emissions across the 18 railway bureaus exhibited spatial heterogeneity. For instance, operating capacity was the main promoting factor for bureaus like Taiyuan, Beijing, Lanzhou, Nanning, Hohhot, Urumqi, and Qinghai-Tibet, while energy consumption intensity was the main inhibiting factor. For Shanghai, Kunming, Wuhan, Chengdu, Xi'an, Zhengzhou, Jinan, Shenyang, Nanchang, and Guangzhou, economic benefits per unit turnover was the main promoting factor, with energy consumption intensity as the main inhibiting factor. For Harbin, energy consumption intensity was the main promoting factor, while economic benefits per unit turnover was the main inhibiting factor. 4) The railway sector can reduce carbon emissions by optimizing transport organization to reduce empty car rates, optimizing energy structure, and retrofitting infrastructure for energy efficiency, while implementing differentiated emission reduction strategies tailored to each bureau's characteristics.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605020
To address the high CO2 emission proportion in the industrial sector, distillers' grain waste was converted into biochar for CO2 adsorption from flue gas. Raw biochar suffers from weak pore adsorption and poor selectivity at elevated temperatures. This study employed ash self-templating and particle self-assembly to create hierarchical pores and simultaneously load amine groups onto distillers' grains-derived biochar, yielding amine-functionalized hierarchical porous carbon spheres. The amine loading significantly increased, providing more CO2 adsorption sites, while retaining macroporosity (total pore volume 0.0030–0.0066 cm3/g after amine loading), which enhanced morphological stability and CO2 mass transfer. The optimal sample, 0.2PW-K-CNF-PEI, exhibited a CO2 adsorption capacity of 1.03 mmol/g at 100 °C, a CO2 diffusion coefficient of 0.0495 min−1, and a selective adsorption capacity of 44 mg/g at 80 °C. This work offers a solution for valorizing distillers' grain by-products and capturing CO2 from low-temperature flue gas.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605024
The refined quantification of carbon footprint in engineering construction projects is critical for formulating targeted carbon reduction strategies during the materialization phase. This study integrates material flow analysis (MFA) with the emission factor method to establish a panoramic carbon flow model for engineering projects. Construction activities are categorized into processing and construction, and office and daily operations, clarifying material and carbon flow relationships within the system boundary and with external systems. Empirical analysis was conducted on the Hejiawan Bridge of Section 11 of the Xiyu High-Speed Railway. Results show that the total carbon flow amounts to 27,482,432.11 kg CO2eq, with direct carbon flow (fuel oil, gasoline) accounting for 7.6% and indirect carbon flow (products, transportation, electricity) accounting for 92.4%. From the material flow perspective, the total carbon flow comprises product carbon flow (72.88%), resource and energy carbon flow (25.73%), transportation carbon flow (1.04%), waste carbon flow (0.35%), and service carbon flow (0.01%). In terms of activity scope, construction-related carbon flow accounts for 99.17%, while office and daily operations account for 0.46%. Two indicators, material consumption carbon flow rate and energy consumption carbon flow rate, are proposed for the first time. Comparative analysis of five girder bridges reveals that the Hejiawan Bridge has a material consumption carbon flow rate of 3.91 kg CO2eq/kg, ranking highest among similar bridges, while its energy consumption carbon flow rate is 13.40 kg CO2eq/kg ec, at a medium level. The assessment indicates relatively high material consumption, suggesting potential for carbon reduction through structural and geological optimization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3973-9
Circularly polarized luminescence (CPL) is a phenomenon where chiral molecules emit light with distinct left or right circular polarizations upon excitation. Unlike conventional luminescent materials, chiral materials produce light with inherent helicity, leading to unique applications in chiral optoelectronics, quantum technologies, and biophotonics. This review systematically explores the theoretical and computational foundations of CPL, focusing on the interplay between molecular chirality, transition dipole moments, and photoluminescence quantum yield. A major challenge in designing efficient CPL-active materials is optimizing the luminescence dissymmetry factor (g_lum) while maintaining high photoluminescence efficiency. This review comprehensively summarizes how first-principles computational methods, by establishing robust predictive frameworks, have significantly advanced the design of CPL molecules. Even though significant progress has been made in modeling monomeric systems, the effective integration of first-principles calculations to describe CPL in aggregated states remains an ongoing challenge. The review also highlights the promising synergy between computational models, experimental validation, and emerging data-driven techniques such as machine learning (ML) for guiding the design of novel high-performance CPL materials. In conclusion, further research is needed to overcome current computational limitations and develop more effective strategies for CPL material design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3854-7
The tertiary spatial structure of biological macromolecules determines their physiological functions. In the formation of the tertiary structure, the secondary structure serves as the assembly foundation, and interactions between secondary structures play a critical role in driving and stabilizing the tertiary architecture. Synthetic foldamers, characterized by their modifiability and structural diversity, can adopt various helical conformations, enabling them to mimic natural protein secondary structures such as the α-helix, while also providing chemical models for studying interactions between secondary structures. This review outlines recent advances in aromatic foldamers and supramolecular helical assemblies formed by helical polymers, with particular attention to unique chiral phenomena observed during the formation of helical secondary structures. It provides a detailed summary of their applications in molecular recognition, ion channels, and circularly polarized luminescence, among others, and discusses future challenges facing aromatic foldamers. The review emphasizes the hierarchical nature of chirality—from primary atomic asymmetry to quaternary higher-order structures—and highlights the importance of understanding non-covalent interactions between helical secondary structures for regulating chiral assembly. Key strategies for constructing chiral helical aromatic foldamers include the use of chiral side chains, terminal groups, and solvent effects, as well as the sergeants-and-soldiers effect and majority-rules principle for chirality amplification. The applications of these foldamers in asymmetric catalysis, chiroptical materials, and biomimetic ion transport are also discussed, underscoring their potential in advanced functional materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4105-8
Chiral europium(III) (Eu(III)) complexes, characterized by their f-f transitions and allowed magnetic dipole transitions, exhibit narrowband emission and superior circularly polarized luminescence (CPL) with high luminescence dissymmetry factors (g_lum), making them promising for circularly polarized organic light-emitting diodes (CP-OLEDs) and 3D displays. Here, we report a pair of R/S-Eu(TTA)3DFPO enantiomers, employing β-diketone 1,1,1-trifluoro-3-(2-thenoyl)acetone (TTA) as the main ligand and point-chiral R/S-tert-butyl(6-(diphenylphosphoryl)dibenzo[b,d]furan-4-yl)(phenyl)phosphine-oxide (R/S-DFPO) as ancillary ligands. In toluene, these enantiomers display characteristic narrowband red emission from the 5D0→7F2 transition of Eu(III), with a maximum emission wavelength of 617 nm, a full width at half maximum of 11 nm, a photoluminescence quantum yield of 43%, and pronounced chiroptical response, evidenced by |g_PL| values of 8.0 × 10^-3 around 590 nm (5D0→7F1 transition). Notably, CP-OLEDs fabricated via vacuum deposition achieve a maximum external quantum efficiency of 4.0% and exhibit obvious circularly polarized electroluminescence with |g_EL| values exceeding 1.0 × 10^-2. These results demonstrate that point-chiral phosphine-oxide ligands provide an effective strategy for achieving coordination-stable chiral Eu(III) complexes for high-performance CP-OLEDs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3956-0
Chiral organic-inorganic hybrid metal halides (OIHMHs) are multifunctional materials with structural diversity and chiroptical properties. However, current chiral OIHMHs predominantly exhibit circularly polarized luminescence (CPL) in the visible spectrum, while ultraviolet and near-infrared (NIR) CPL remains challenging. Here, we report lead-free chiral zero-dimensional (0D) OIHMHs, (R/S-DACH)2In2Br10:Sb3+/Yb3+ (DACH = 1,2-diaminocyclohexane), featuring spectrally tunable CPL emissions covering visible to NIR regions. Single-crystal X-ray diffraction, circular dichroism, and CPL spectroscopy revealed that robust hydrogen-bonding interactions between organic cations and inorganic emitters are crucial for chirality expression. Sb3+-doped (R/S-DACH)2In2Br10 single crystals exhibited intense broadband emission at 644 nm from the 3P1 to 1S0 transition of Sb3+, achieving a record photoluminescence quantum yield (PLQY) of 49.9% (two orders of magnitude higher than pristine crystals) and a luminescence dissymmetry factor (glum) of ±7.1×10−3. Notably, Sb3+/Yb3+ co-doped crystals simultaneously generated dual-band CPL at 644 nm (glum = ±2.1×10−2) and 994 nm (glum = ±6.8×10−3), representing an important example of NIR-CPL in OIHMHs. An LED device based on (R-DACH)2In2Br10:2.7%Sb3+ exhibited bright orange emission with a color-rendering index of 78.4 and excellent spectral and operational stabilities. These findings establish a design strategy for broadband CPL and expand applications of chiral metal halides in advanced optoelectronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3784-9
Symmetry-breaking charge separation (SB-CS) is a fundamental process in natural photosynthesis and holds promise for organic semiconductor applications. However, the influence of SB-CS on excited-state chirality has remained unexplored. Here, we employ femtosecond time-resolved circularly polarized luminescence (TRCPL) and transient absorption (TA) spectroscopy to investigate the excited-state chirality dynamics of a chiral perylenediimide bichromophore (Cy-PDI 2). Our results reveal that the locally excited (LE) state decays to a symmetry-breaking charge-separated (SB-CS) state within 88 ps in tetrahydrofuran (THF), while this process is strongly quenched in toluene (TOL). Time-dependent emission dissymmetry factor g_lum(t) extracted from TRCPL kinetics demonstrates a one-order-of-magnitude enhancement of circularly polarized luminescence after SB-CS, directly reflecting the asymmetry of electron cloud distribution on an ultrafast timescale. This work provides the first direct observation of excited-state chirality evolution during SB-CS and proposes a mechanistic framework. Our findings offer deeper insight into the origin of excited-state chirality, which is crucial for understanding efficient energy transfer, enantiospecific recognition, and asymmetric catalysis in biological and chemical systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3650-6
Aggregation-induced emission active chiral polymer dots (AIE@CPdots) are emerging as high-performance emission layers (EMLs) for circularly polarized organic light-emitting diodes (CP-OLEDs) due to their persistent emission stability, high photoluminescence quantum yields, excellent solution processability, facile functionalization, tunable bandgap-governed emission, and superior device processability. However, reports on such systems remain scarce. In this study, a pair of chiral conjugated polymer enantiomers (R/S-PFC) was synthesized via Suzuki polymerization using three monomers: a chiral binaphthalene moiety, a fluorenyl linker, and an AIE-active cyanostyrene dye. After annealing at 110 °C, the resulting R/S-PFC self-assembled into chiral nanoparticles (AIE@CPdots) in a chloroform/n-hexane mixed solvent (9:1 v/v), exhibiting enhanced circularly polarized luminescence with a luminescence dissymmetry factor (|g_lum|) of 4.4 × 10⁻³ at 462 nm. Notably, AIE@CPdots served as the EML in CP-OLEDs, achieving high-performance circularly polarized electroluminescence with an electroluminescence dissymmetry factor (|g_EL|) of 3.0 × 10⁻³ at 464 nm, a maximum luminance (L_max) of 6022 cd m⁻², and a maximum current efficiency (CE_max) of 1.10 cd A⁻¹. This work provides a novel strategy for designing superior EML materials for CP-OLEDs via chiral self-assembled AIE@CPdots.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3834-x
Lithium metal anodes face critical barriers to practical application due to dendritic growth and interfacial instability, which cause short cycle life and safety hazards. This work introduces a highly stable and ultrahigh-rate lithium metal anode using a lithiophilic Sm2S3-modified carbonaceous host. The in situ formation of a Li2S-reinforced interphase layer enables highly reversible lithium plating/stripping and uniform deposition. The modified anode achieves an ultrahigh rate capability of 20 mA cm−2 and ultralong cycling stability of 7440 cycles with dendrite-free morphology. In a 4.5 V anode-less Li||LiCoO2 cell with an areal capacity of ~1.93 mA h cm−2, the system sustains over 1100 cycles with 87.2% capacity retention under harsh conditions: an ultralow negative-to-positive capacity ratio (N/P) of ~0.26 and lean electrolyte of ~5 g Ah−1. Furthermore, an anode-less pouch cell with an ultrahigh areal capacity of ~6.01 mA h cm−2 delivers superior cycling performance even at an ultra-low N/P ratio of ~0.71 and ultra-lean electrolyte of ~1 g Ah−1, achieving a high energy density of 505 Wh kg−1. This work provides a scalable and effective strategy for advancing reliable, practical lithium metal batteries.