SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4419-1
Proton exchange membrane fuel cells (PEMFCs) fed with reformate hydrogen suffer severe anode poisoning by trace CO, necessitating high CO electrooxidation potentials that degrade performance and durability. This work introduces a Pt@CrSA-N-C anode catalyst featuring a hydrophilic Cr single-atom interface that simultaneously weakens CO adsorption on Pt via electronic regulation and promotes water activation, thereby lowering the CO oxidation onset potential to approximately 0.13 V vs. RHE. The onset potential was determined by two independent methods: the first potential at which the background-corrected current exceeds 0 mA cm-2 during CO oxidation reaction tests in a three-electrode system, and the potential at which the forward scan current exceeds the N2 background current in CO-stripping voltammetry. The catalyst achieves a maximum power density under 100 ppm CO that surpasses reported advanced catalysts, as compiled in Table S5. Structural, spectroscopic, and electrochemical characterizations collectively establish a coherent rationale for the hydrophilic single-atom interface strategy. This approach addresses the longstanding trade-off between CO tolerance and Pt utilization, offering a viable route for low-potential CO removal in practical PEMFC anodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4439-4
Silk fibroin (SF) hydrogels are promising for neural regeneration but suffer from progressive stiffening due to excessive β-sheet assembly, limiting their use in traumatic brain injury (TBI) repair. This study introduces a dopamine (DA)-mediated synergistic topological entanglement strategy to construct an SF-DA/gelatin-DA composite hydrogel (SG). The system integrates covalent cross-linking, net cationic electrostatic repulsion, hydrogen bonding, and π-π stacking to regulate SF assembly dynamics at the molecular level. The resulting SG hydrogel maintains stable mechanical softness over extended periods, with a storage modulus of approximately 1.2 kPa after 28 days, compared to a 5-fold increase in pure SF hydrogels. The sustained softness promotes neural stem cell (NSC) proliferation and differentiation, with a 2.5-fold increase in βIII-tubulin expression and a 1.8-fold increase in GFAP expression after 14 days. In a rat TBI model, SG hydrogel implantation reduced glial scar formation by 40% and improved neurological function scores by 30% at 8 weeks. The hydrogel degrades at a rate of 12% per week, matching tissue regeneration. This multi-crosslinking approach offers a clinically translatable strategy for neural tissue engineering, addressing the critical bottleneck of mechanical instability in SF-based biomaterials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4472-0
Dynamic electrocardiography (ECG) monitoring during physical activity remains compromised by motion artifacts that corrupt signal fidelity, particularly with conventional gel electrodes whose impedance rises sharply under deformation. This work presents a thumb-sized liquid metal system integrating gallium-based epidermal electrodes with a self-adhesive elastomeric matrix to sustain robust ECG acquisition against motion. The electrodes exploit the fluidic compliance of eutectic gallium–indium to maintain continuous skin contact, while the adhesive formulation ensures stable interfacial coupling without additional fixation. The system achieves low motion artifact levels, preserving waveform morphology and R-peak detectability during ambulation. The compact form factor enables unobtrusive wearability, and the materials architecture addresses the trade-off between adhesion and conformability that limits existing dry electrodes. The study establishes a materials and device pathway for clinical-grade dynamic ECG in ambulatory and point-of-care settings, with implications for continuous cardiac monitoring where patient movement is unavoidable.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4320-4
Colloidal lead halide perovskite quantum dots (Pe-QDs) have achieved external quantum efficiencies exceeding 20% in red, green, and blue light-emitting diodes (LEDs), yet their integration into high-resolution displays is impeded by two persistent bottlenecks: the intrinsic ionic lability of Pe-QDs, which compromises structural and environmental stability, and the absence of mild, high-fidelity patterning techniques that avoid ligand detachment and surface defect formation. This work addresses both obstacles through a dual strategy. First, a ligand-fluoride co-stabilization method yields shape-defined, colloidally stable rhombic dodecahedral CsPbBr3 Pe-QDs; subsequent fluorine surface reconstruction using tetrabutylammonium fluoride (TBAF) enhances ligand binding affinity, producing BHOA+F CsPbBr3 Pe-QDs with a photoluminescent quantum yield (PLQY) of 94.6%. Accelerated ageing, ultraviolet irradiation, and thermal cycling tests confirm improved structural and environmental stability. Second, capillary liquid-bridge confined assembly enables reproducible, scalable fabrication of pixelated Pe-QDs with in-plane long-range order, vertical confinement, and precise spatial patterning. The resulting pixelated Pe-QDs LEDs exhibit high efficiency, sufficient brightness, and long operational stability, with the approach generalizable across red, green, and blue Pe-QDs for wide color gamut displays. This combination of surface fluorination and liquid-bridge assembly represents a landmark achievement in high-resolution display technology.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4479-8
The von Neumann architecture is increasingly constrained by energy consumption and data-transfer efficiency as artificial intelligence and data-intensive applications expand. Neuromorphic computing, inspired by the human brain's information-processing mechanisms, offers an alternative paradigm. Two-dimensional (2D) ferroelectric materials are promising candidates due to their intrinsic non-volatility, atomic-scale thickness, ultra-low power consumption, excellent fatigue endurance, and dangling-bond-free surfaces. This review examines recent advances in 2D ferroelectric materials and associated device architectures for neuromorphic applications. It first introduces ferroelectric mechanisms and representative 2D ferroelectrics, then surveys key device architectures including ferroelectric tunnel junctions, diodes, transistors, and photovoltaic devices. Their applications in in-memory computing and in-sensor neuromorphic systems are discussed, with emphasis on artificial neural networks, spiking neural networks, reservoir computing, and neuromorphic perception for efficient information processing and intelligent sensing. The unique properties of 2D ferroelectrics enable integrated sensing, memory, and computing functionalities, demonstrating potential for future neuromorphic and brain-inspired intelligent systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4505-9
Transition metal hydroxides are promising oxygen evolution reaction (OER) catalysts for alkaline water electrolysis. This study reports Ce-doped Co(OH)2 electrocatalysts synthesized via one-step electrodeposition, where the Ce3+/Ce4+ ratio is precisely controlled by deposition temperature. The optimized Ce-Co(OH)2 catalyst, obtained at 40°C, exhibits an overpotential of 236 mV at 10 mA cm-2 and maintains stability for 200 h. In an anion-exchange membrane water electrolyzer (AEMWE), the Ce-Co(OH)2 anode achieves a cell voltage of 2.04 V at 1 A cm-2 and operates for over 500 h at 500 mA cm-2. Mechanistic analysis reveals that Ce3+/Ce4+ dynamic electron buffering regulates surface reconstruction: during OER, electron transfer direction reverses (Ce → O → Co), with Ce donating electrons to Co sites to prevent over-oxidation and structural collapse. This work establishes a versatile strategy for balancing surface reconstruction and structural stability in Co-based OER catalysts, providing a foundation for designing high-performance, durable alkaline water oxidation electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4467-x
Conventional eye-movement interaction systems depend on video capture, infrared tracking, and image recognition, which impose inherent constraints on accuracy, response latency, and stability. This study introduces an eyelash-guided signal interaction system based on a triboelectric nanogenerator (PF-TENG) using PDMS-FDTS thin films. The system employs eyelash movements as interactive inputs, eliminating the need for complex optical acquisition devices. A CNN-LSTM hybrid neural network classifies distinct eyelash movement patterns with a classification accuracy exceeding 98.5%. The PF-TENG device exhibits ultra-flexibility and transparency, enabling seamless integration onto eyeglasses without obstructing the user's field of view. Experimental validation demonstrates real-time monitoring of ocular states for driving fatigue detection, accurately identifying fatigue signs and enhancing application potential in intelligent driving. The system offers a natural, comfortable input modality and significant advantages for human-machine interaction, with broad prospects in eye-movement control and intelligent transportation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4343-7
Piezoelectric materials interconvert mechanical and electrical energy, but piezoceramics are brittle while PVDF-based ferroelectric polymers exhibit low piezoelectric coefficients (d33 ≈ -30 pC N-1). Chemical modification via morphotropic phase boundary (MPB) engineering has raised d33 in P(VDF-TrFE) to -63.5 pC N-1, and to -69 pC N-1 with stretching, but intrinsic piezoelectricity in relaxor terpolymers remains limited. Here, relaxor ferroelectric P(VDF-TrFE-CFE) with varying C=C double bond (DB) content is synthesized via dehydrochlorination. Structural and electrical characterization reveals that increasing DB content stabilizes long-range ferroelectric order while suppressing short-range relaxor characteristics, forming a trans/helix phase boundary. At a critical DB content of 2.0 mol%, a markedly enhanced intrinsic d33 of -129.0 pC N-1 is achieved, outperforming previous MPB approaches. This finding addresses the fundamental bottleneck of low piezoelectric response in flexible ferroelectric polymers and provides a viable route for high-performance wearable electromechanical devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4248-2
Marine biofouling imposes substantial operational penalties on maritime assets, yet commercial silicone foul-release coatings rely on static, non-adaptive networks that cannot be reprocessed or repaired. This work introduces selenonium-salt-catalyzed dynamic siloxane exchange as a route to polydimethylsiloxane (PDMS) vitrimer coatings. The authors incorporate A16Se+ organoselenium catalysts into PDMS networks at loadings designated A16Se+xPDMS, enabling thermally activated siloxane bond exchange that confers vitrimeric stress relaxation, reprocessability, and high-temperature self-healing. Antibiofouling performance is benchmarked against pristine PDMS using colony morphology assays for Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa, SEM imaging of bacterial adhesion after 3 h, Chlorella fluorescence adhesion quantification, zeta potential measurements, and 3-month seawater immersion panels. Reviewer 1 questioned the direct relevance of recyclability and high-temperature self-healing to marine antifouling and requested that surface elastic modulus and Pseudomonas antibacterial data be elevated to the main text. In response, the authors relocated scratch and self-healing results from Figure 5 to Supporting Information Figures S12 and S13, condensed the main-text discussion, and integrated surface elastic modulus data into Figure 4G and Pseudomonas antibacterial results into Figure 6A. The revised manuscript positions dynamic exchange as supporting evidence of network dynamics rather than as a primary antifouling metric, while foregrounding modulus and antibacterial performance as the application-relevant properties.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4418-7
Glioblastoma (GBM) remains the most lethal primary brain tumor, with the blood-brain barrier (BBB) severely restricting effective treatment options. Immunotherapy has achieved remarkable success in cancers such as lung cancer and melanoma, yet its efficacy in GBM is constrained by the immunosuppressive tumor microenvironment and a paucity of tumor-infiltrating T cells. This study developed a biomimetic nanocomposite for the co-delivery of an immunogenic cell death (ICD) inducer and an indoleamine 2,3-dioxygenase 1 (IDO-1) inhibitor to overcome these challenges. Paclitaxel-derived carbon dots (PCDs), which induce ICD in tumor cells and promote the recruitment and activation of immune cells, were synthesized and assembled with Indoximod (an IDO-1 inhibitor) to form a nanocomposite (P-In). A biomimetic coating was subsequently applied to create M@P-In. This coating significantly enhanced BBB penetration and tumor cell uptake. The M@P-In nanocomposite efficiently induced ICD in tumor cells and inhibited IDO-1 activity via the released Indoximod, thereby reversing T-cell suppression and activating antitumor immune responses. Consequently, M@P-In demonstrated potent antitumor efficacy against glioblastoma in vivo with minimal systemic toxicity. This work presents a novel and promising strategy for immunochemotherapy against GBM by co-delivering a carbon dot-based ICD inducer and an IDO-1 inhibitor to the tumor site.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4267-y
The synthesis of two-dimensional MBenes from MAB-phase ceramics is impeded by uncontrolled etching kinetics that compromise structural integrity and yield. This study introduces a vacuum molten salt strategy to regulate space-charge accumulation during the selective removal of Al from Mo2AlB2, producing honeycomb-like architectures. The vacuum environment suppresses oxidative side reactions and modulates ionic transport, enabling precise control over etching depth and morphology. The resulting Mo2AlB2 exhibits exceptional electromagnetic wave absorption, with a minimum reflection loss of -56.3 dB at 2.4 mm and an effective absorption bandwidth of 6.8 GHz. These metrics surpass conventional etching-derived MBenes by a factor of 2.5 in attenuation capacity. The space-charge-regulated mechanism is elucidated through in situ spectroscopic and computational analyses, revealing that vacancy-induced charge redistribution governs the etching front propagation. This work establishes a scalable route for high-purity MBenes with tailored porosity, addressing critical bottlenecks in energy absorption and catalytic applications. The vacuum molten salt approach eliminates the need for hazardous HF, offering a safer and more environmentally benign pathway for industrial translation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4405-9
Conventional metal-halide X-ray scintillators, including Bi4Ge3O12 (BGO), Cs(Na)I:Tl, and Lu1.8Y0.2SiO5:Ce (LYSO), suffer from hygroscopic decomposition, high-temperature fabrication, and mechanical rigidity, which restrict their deployment in harsh-environment radiography. This study reports a nontoxic zero-dimensional organic–inorganic hybrid copper(I) halide, Cu2I2(C26H36NP)2 (Compound G), synthesized via a room-temperature solution route. The bulky phosphine ligands confer exceptional superhydrophobicity, with the material retaining 91.95% of its initial luminescence after 30 days of water immersion. A flexible scintillator screen fabricated from styrene-ethylene-butene-styrene (SEBS) exhibits a light yield of ~32,500 photons MeV-1, a spatial resolution of 19.14 lp mm-1, and a detection limit of 0.8 μGyair s-1. The screen enables stable X-ray imaging under flexible, high-temperature, and underwater conditions, eliminating vignetting and distortion in nonplanar objects. These metrics demonstrate that the superhydrophobic copper(I) halide scintillator addresses the water-stability bottleneck of commercial scintillators while delivering competitive light output and resolution, offering a viable pathway for medical diagnosis, nondestructive inspection, security checking, and space exploration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4448-y
Zero-dimensional (0D) hybrid metal halides are promising for optoelectronic displays, bioimaging, and anti-counterfeiting due to strong exciton localization and self-trapped exciton (STE) emission. However, low-toxicity, biocompatible zinc halides with blue emission remain scarce, hindered by structural isolation of [ZnBr4]2− tetrahedra, electron-phonon coupling, lattice distortion, and nonradiative relaxation. Here, we synthesize MPAZnBr4 (MPA = N-(3-aminopropyl) morpholine), a 0D zinc bromide halide. Single-crystal X-ray diffraction reveals a monoclinic P21/c space group with a = 6.65190 Å, b = 16.11210 Å, c = 13.79640 Å, β = 94.5700°, Z = 4, and a calculated density of 2.394 g/cm3. The isolated [ZnBr4]2− tetrahedra are hydrogen-bonded to MPA cations, with the shortest Br···Br contact of 4.76 Å indicating weak inter-cluster electronic coupling. Upon photoexcitation, MPAZnBr4 exhibits bright blue emission centered at 450 nm with a full width at half maximum of 135 nm. Wavelength-dependent emission mapping confirms a single radiative pathway, while temperature-dependent photoluminescence identifies triplet STE emission with a thermal quenching activation energy of 55 meV. The extensive hydrogen-bonding network imparts remarkable structural stability, showing negligible photoluminescence decay under prolonged excitation or storage. As a proof-of-concept, we demonstrate switchable and rewritable information encryption and decryption, enabling complex luminescent patterns. These findings provide a strategy for constructing highly stable, low-toxicity blue-emissive Zn-based 0D metal halides for advanced photonic and information-security applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4473-9
Selective ion separation is critical for resource recovery, water treatment, lithium extraction from salt lakes, and nuclear waste management, yet the differences in size, solvation structure, and coordination behavior among ions are often minimal, and separation is further complicated by valence, interfacial charge, and competing ions. Nanoporous materials with tunable sub-nanometer channels and chemically active interfaces can regulate ion entry, solvation reorganization, interfacial partitioning, intrapore migration, and release. This review examines three mechanistic categories—size and solvation sieving, chemical recognition, and dynamic gating—from the perspective of confined transport and ion–pore interactions, and compares their roles and coupling in systems of monovalent–monovalent, divalent–divalent, heterovalent, and chemically similar multivalent ions. We further distinguish selective adsorption, membrane enrichment, and transmembrane transport, and discuss how selectivity definitions, ion flux, feed composition, driving force, and operating time affect performance evaluation. Current research faces three major challenges: lack of comparability of performance data across different test conditions, insufficient direct evidence of ion solvation, site occupancy, and migration under operating conditions, and the complexity of feed streams. By adopting a sequential ion transport process as a unified conceptual framework, this review systematically compares separation mechanisms across diverse nanoporous materials, including MOFs, COFs, zeolites, 2D materials, microporous polymer membranes, ion-exchange membranes, biomimetic nanochannels, organic–inorganic composites, functionalized porous carbons, and biochars. This transport-process-oriented framework provides a general and mechanistic perspective for understanding and comparing selective ion separation across diverse nanoporous platforms.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4494-9
Superionic conductors exhibit high cation mobility arising from weak binding and continuous transport pathways, atomistically characterized by extensive structural disorder and partial occupancy akin to amorphization. This disorder, whether confined to a cation sublattice or extended to full amorphization, strongly impedes lattice thermal transport, rendering these materials intrinsically ideal thermal insulators. This work investigates Ag26I18W4O16, a superionic conductor tunable from fully amorphous to single-crystalline states, as a model system to probe the impact of disorder and amorphization on thermal transport. Extensive Ag+ disorder, in both crystalline and amorphous phases, reduces thermal conductivity to approximately the theoretical lower bound of 0.16 W/m-K with virtually no temperature dependence, while concurrently achieving the lowest mean sound velocity ever recorded for a dense solid. Pair distribution function (PDF) analysis of synchrotron X-ray total scattering data indicates that short-range disorder (< 5 Å), rather than long-range periodicity, governs thermal insulation performance in both phases. These findings suggest a design strategy reconciling structural stability with glass-like thermal insulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4466-3
Conventional surface coating technologies for 45 steel are constrained by high processing temperatures, limited material compatibility, and insufficient interfacial bonding. This study introduces ultrasonic vibration-assisted mechanical coating (UVAMC) as a low-temperature deposition route that mitigates these limitations. The process yields a chromium coating on 45 steel with a nanoscale elemental interdiffusion transition layer at the interface, achieving a bonding strength of 66.0 MPa. The coating delivers improved corrosion resistance in aggressive environments while preserving the substrate's original compressive and tensile strength. The method also demonstrates broad process adaptability, successfully depositing copper, aluminum, and 316 stainless steel powders, and forming complex shapes such as the "SZU" pattern. These results establish UVAMC as a viable surface functionalization strategy for metallic materials, combining efficient deposition with operational flexibility.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4477-7
The rapid demand for high-energy-density lithium batteries necessitates advanced solid-state electrolytes (SSEs) to overcome the safety and performance limitations of conventional liquid counterparts. Macrocyclic compounds, with their well-defined cavities, programmable binding sites, and tunable self-assembly, have emerged as powerful molecular regulators for designing next-generation SSEs. This review examines recent advancements in macrocyclic compound-based SSEs by categorizing their functions into four fundamental supramolecular regulation paradigms: cation-centered regulation (e.g., crown ethers), anion-centered regulation (e.g., calixarenes and calixpyrroles), channel-dominated transport (e.g., cyclodextrins), and hybrid regulation (e.g., cucurbiturils). We elucidate how these macrocycles precisely control ion coordination, modulate migration dynamics, and reshape interfacial chemistry, leading to enhanced ionic conductivity, improved Li+ transference numbers, suppressed lithium dendrite growth, and superior interfacial stability. While each paradigm offers distinct advantages, the most promising SSEs often leverage synergistic combinations of these strategies. Finally, we highlight the remaining challenges, including synthetic complexity and multi-objective performance trade-offs, and propose future research directions for developing highly efficient and durable macrocycle-based solid-state lithium batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4288-1
The high-temperature oxidation resistance of Cr2AlC MAX phase ceramics is severely compromised by rapid Al depletion and the formation of a brittle sub-surface Cr7C3 layer. This study elucidates how trace Y2O3 doping (0.25 and 0.5 wt.%) modulates the oxidation behavior of Cr2AlC at 1100 °C. The incorporation of 0.5 wt.% Y2O3 significantly suppresses the parabolic rate constant compared to undoped counterparts. This kinetic suppression is attributed to the Reactive Element Effect (REE), where Y3+ segregation at α-Al2O3 grain boundaries inhibits outward Al3+ diffusion, shifting the scale growth mechanism to inward oxygen diffusion control. Consequently, this retarded Al consumption prevents the decomposition of the Cr2AlC substrate into Cr7C3. While undoped specimens fail due to volume contraction and Kirkendall voiding associated with the Cr7C3 interlayer, specimens with the most effective doping content within the investigated range maintain a stable, atomically sharp α-Al2O3/Cr2AlC interface devoid of voids and decomposition products. The superior adhesion of this interface is attributed to three synergistic factors: the elimination of volumetric mismatch induced by phase transformation, the mechanical interlocking provided by Y-rich oxide pegs, and the intrinsically higher interfacial bonding strength of the α-Al2O3/Cr2AlC system as confirmed by DFT calculations. These findings provide a mechanistic framework for designing oxidation-resistant MAX phase ceramics via reactive element doping.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4313-7
Liquid-to-vapor mass transfer is central to energy and environmental processes. Conventional distillation relies on vapor-liquid equilibrium and device-level optimization, with materials playing passive structural roles. Non-boiling processes such as membrane distillation and interfacial solar evaporation localize phase change at confined interfaces, making mass transfer a materials-mediated transport phenomenon where interfacial structure and chemistry dictate evaporation kinetics, vapor escape, and solute rejection. Janus interface materials, featuring spatially separated hydrophilic and hydrophobic domains, introduce architectural asymmetry to regulate liquid-to-vapor mass transfer. This review summarizes recent advances, highlighting mechanisms including the cooperative pump-valve effect, nanoconfinement-enhanced transport, and mitigation of fouling and scaling. Representative applications in membrane distillation, solar-driven evaporation, and personal thermal-moisture management are systematically discussed. Key challenges and future opportunities are outlined, particularly in advancing fundamental understanding, scalable fabrication, and practical implementation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4468-6
The proliferation of multispectral detection platforms demands materials that simultaneously satisfy electromagnetic interference (EMI) shielding and infrared (IR) camouflage without compromising radio-frequency (RF) transmission. Conventional MXene films exhibit exceptional EMI shielding (>40 dB) but suffer from high IR emissivity and severe RF reflection, precluding integration with wave-transmitting arrays. This work introduces liquid metal (LM)-modified MXene composite films engineered via structural patterning to decouple optical, IR, and RF responses. The LM phase, dispersed within the MXene interlayer galleries, reduces free-electron density and tailors the dielectric loss, while a periodic array architecture creates impedance-matched windows for RF transmission. The resulting films achieve an EMI shielding effectiveness of 36 dB at 510 µm thickness, with a low IR emissivity of 0.36 and an RF transmittance exceeding 80% in the X-band. The patterning strategy suppresses surface current continuity, mitigating the trade-off between shielding and transmission. These metrics represent a 20% improvement in IR camouflage and a 15% enhancement in RF transparency relative to pristine MXene films. The composite films also demonstrate mechanical flexibility, retaining 95% of initial conductivity after 1,000 bending cycles. This work establishes a scalable route for multispectral-compatible materials critical for next-generation stealth and communication systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4165-1
Developing efficient photocatalysts for hydrogen peroxide (H2O2) synthesis is vital for sustainable chemistry, yet optimizing the electronic structure of triazine-based covalent organic frameworks (COFs) through precise spatial engineering remains a challenge. In this work, we constructed four model COFs to systematically decode how the spatial arrangement and incorporation level of triazine moieties regulate the electronic structures and H2O2 production efficiency. Combined experimental and theoretical analyses revealed that FB-AT achieved an optimal donor-acceptor architecture via rational spatial arrangement of triazine and benzene moieties. This configuration established an intramolecular potential gradient, which not only promoted charge separation by suppressing the exciton binding energy but also enriched the electron density at triazine sites. These electron-rich active centers significantly facilitated the oxygen reduction reaction by lowering the thermodynamic energy barrier for *OOH intermediate formation. Consequently, FB-AT exhibited a remarkable H2O2 production rate of 11055 μmol g-1 h-1 in pure water, along with a superior solar-to-chemical conversion efficiency of 1.16%. Additionally, FB-AT enabled complete degradation of phenol, tetracycline, and rhodamine B within 5–15 min of visible light irradiation. This work provides crucial guidance for the rational design of advanced COF photocatalysts for sustainable H2O2 production and water decontamination.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4275-3
Electrochemical in-situ production of active chlorine (AC) via chlorine evolution reaction (CER) can alleviate hull corrosion and residual chlorine overage, which is a highly reliable disinfectant for sewage and ballast water. Nonetheless, the primarily competitive oxygen evolution reaction and gradual anode passivation hinder its practical application. Herein, we employed the in-situ hydrothermal strategy to synthesize Ru/TiO2-x to realize high activity and selectivity of CER. The robust interaction of Ru sites and TiO2-x achieved via a one-step hydrothermal synthesis strategy, the structural and valence state characterizations confirm that Ti3+ stabilizes Ru solely in the metallic state (Ru0) via structural confinement effects, effectively inhibiting catalyst oxidation. As a result, the Ru/TiO2-x requires only an overpotential of 33 mV to reach 10 mA cm−2, and possess strong catalytic durability, sustaining continuous operation for 100 h with negligible current decay. Further integration with a triboelectric nanogenerators successfully realizes the generation of AC, which demonstrates a >99.9% inactivation efficiency against Escherichia coli in simulated seawater environments, while also effectively degrading ammonia nitrogen and urea contaminants in domestic wastewater.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4294-4
Room-temperature phosphorescence (RTP) polymer materials are attractive for flexible electronics and information encryption due to their tunability and processability. However, achieving polymeric RTP systems that simultaneously exhibit high thermal sensitivity, reversible multicolor emission, and long phosphorescence lifetime (τPhos) with high quantum yield (ΦPhos) remains challenging. Here, we report an in-situ cross-linked self-assembly strategy that converts flexible polymers into rigid polymer microspheres, yielding long τPhos, high ΦPhos, and thermally and time-dependent tunable RTP. The resulting microspheres (PM0.1-0.01-1) exhibit a maximum τPhos of 1754 ms and ΦPhos of 42.83%, markedly superior to previously reported intrinsic polymer RTP materials. At 77 K, they display ultralong green emission with a lifetime of 6019 ms and visible afterglow lasting up to 99 s. The cross-linked microspheres enable time-dependent, continuously tunable RTP and thermally responsive color switching, while maintaining excellent phosphorescence stability in aqueous and high-temperature environments. This provides a versatile platform for dynamic information encryption, full-color afterglow LEDs, and temperature sensing. The strategy establishes a general design principle for developing multidimensional, controllable, and stable high-performance polymer RTP materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4502-1
Near-infrared-II (NIR-II, 1000-1700 nm) luminescent materials are pivotal for deep-tissue bioimaging and optical communication, yet their performance is often limited by low quantum yields and thermal quenching. Here, we report a thermal-enhanced NIR-II luminescence in Sb3+/Er3+ co-doped Cs3GdCl6 microcrystals synthesized via a modified Bridgman method. Under ultraviolet excitation, the co-doped microcrystals exhibit intense NIR-II emission centered at 1532 nm corresponding to Er3+: 4I13/2 → 4I15/2 transition, with a maximum relative sensitivity of 1.2% K−1 at 303 K. Notably, the integrated NIR-II emission intensity increases by 2.3-fold from 298 K to 373 K, demonstrating anomalous thermal enhancement. This behavior is attributed to the thermally activated energy transfer from Sb3+ sensitizers to Er3+ activators, as confirmed by temperature-dependent photoluminescence spectra and decay kinetics. The energy transfer efficiency reaches 86% at room temperature and further improves with rising temperature. The microcrystals also show excellent photostability, retaining 95% of initial intensity after 120 min continuous UV irradiation. Furthermore, we demonstrate a proof-of-concept wireless optical communication link using the microcrystals as a NIR-II phosphor, achieving a signal-to-noise ratio of 30 dB at 400 Hz modulation frequency. These findings provide a new strategy for designing thermal-enhanced NIR-II luminescent materials and expand their potential in temperature sensing and optical communication.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4306-5
Olefin-paraffin separation is a critical and energy-intensive process in the petrochemical industry, with ethylene and propylene purification alone consuming 0.3% of global energy. Current distillation methods are energy-inefficient, and polymer membranes exhibit inadequate separation performance. Metal-organic frameworks (MOFs), particularly ZIF-8, offer precise molecular sieving due to their uniform pore aperture (~3.4 Å), which lies between the kinetic diameters of propylene and propane. Despite excellent lab-scale performance, ZIF-8 membranes face scalability challenges, with effective areas typically below 10 cm², far from the tens of thousands to millions of square meters required industrially. This paper reviews a recent breakthrough by Weihong Xing, Yichang Pan, and colleagues, who developed a micro-space transformation process (MSTP) for scalable fabrication of heterostructured ZIF-8 (HZIF-8) membranes. Using sealed inner lumens of tubular ceramic supports as confined reaction spaces, they achieved single-tube areas of ~200 cm² and total fabricated areas exceeding 4.6 m². The membranes demonstrated stable separation performance over 30 days at 17 bar and 55 °C with a feed flow of 20 Nm³ d⁻¹. This work represents a significant step toward industrial application, addressing critical bottlenecks in membrane area expansion, defect control, and mechanical stability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4244-0
Near-infrared perovskite light-emitting diodes (NIR-PeLEDs) suffer from poor operational stability, largely due to interfacial reactions at the electron-transport layer (ETL)/perovskite interface. Here, we introduce a zinc ion (Zn2+)-chelated hybrid ETL derived from a Zn2+-chelated polyethylenimine ethoxylated (PEIE) complex, which partially retains the surface properties of ZnO but exhibits significantly reduced oxygen defects and surface-adsorbed hydroxyl groups. This well-modulated surface promotes perovskite crystallization and mitigates interface-induced deprotonation of organic cations during device operation. Consequently, NIR-PeLEDs employing this hybrid ETL achieve a peak external quantum efficiency (EQE) of 20.1%, a high radiance of 652 W sr-1 m-2, and an exceptional T50 lifetime of 270.7 hours at a high current density of 100 mA cm-2, which is over five times that of devices based on conventional ZnO nanocrystal (NC) ETLs. Our results present an effective ETL strategy for operationally stable NIR-PeLEDs and thoroughly reveal the critical role of regulating interfacial reactions in stabilizing buried interfacial contacts. These findings provide valuable insights for advancing perovskite optoelectronic devices that suffer from interface-induced performance degradation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4211-y
Small interfering RNA (siRNA) holds promise for selective silencing of oncogenic drivers, yet its clinical translation is hindered by endosomal entrapment and inefficient cytosolic delivery. This review systematically examines the biological barriers to siRNA function, emphasizing that successful gene silencing requires not only cellular uptake but also endosomal escape, carrier dissociation, and RISC loading. We categorize current delivery strategies into carrier-free systems and stimuli-responsive carriers. Carrier-free approaches utilize coordination chemistry, molecular self-assembly, or peptide conjugation to form stable siRNA complexes that undergo intracellular dissociation. Stimuli-responsive carriers exploit endogenous tumor cues (e.g., acidic pH, elevated glutathione, specific enzymes, ATP) or exogenous triggers (e.g., light, ultrasound, magnetic fields) to achieve spatiotemporally controlled release. The review highlights recent advances in both strategies, with a focus on their application in cancer therapy. We critically assess the challenges that remain, including heterogeneity of tumor microenvironments, scalability of synthesis, and in vivo stability. Finally, we outline future directions for translating siRNA-based therapies into clinical practice, emphasizing the need for rational design of delivery systems that integrate multiple stimuli-responsiveness and active targeting to overcome biological barriers.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4284-5
This highlight summarizes a recent breakthrough in integrated visual sensing and computing using symmetry-reconfigurable photodiodes (SRPDs). The device architecture comprises a metal-semiconductor-metal configuration with AgBiS2 as the active layer, enabling dynamic symmetry breaking through voltage-controlled silver filament formation. The SRPD exhibits broadband photosensitivity from 360 nm to 1,550 nm at an illumination intensity of 115 mW cm-2, as demonstrated by multiwavelength time-resolved photocurrent responses. The device can be programmed into fifteen distinct photoresponsivity states, facilitating analog memory and neuromorphic computing. In imaging experiments, an SRPD-based sensory chip successfully captured images through visibly non-transparent inked glass at 808 nm, highlighting its capability for information-lossless acquisition in scattering media. Furthermore, the device achieved high-accuracy pattern recognition with nearly zero false neuron outputs when projecting specific patterns (├, ┬, ┤), each correlating to a unique current output. As a proof of concept, real-time eye-tracking control of an unmanned aerial vehicle (UAV) was demonstrated, enabling the UAV to follow and monitor a moving cyberdog. These results underscore the potential of SRPDs for processing-in-sensor applications, neuromorphic vision, and human-machine interfacing, offering a compact solution that merges sensing and computing functionalities.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4295-5
Carbon nanomaterials (CNMs), including carbon nanotubes, graphene, and fullerenes, exhibit exceptional promise in precision biomedicine due to their tunable biocompatibility, programmable surface chemistry, large specific surface area, and quantum confinement effects. However, their clinical translation is hindered by aggregation, poor physiological dispersibility, and limited targeting specificity. This review systematically elaborates on surface engineering strategies—covalent functionalization, non-covalent assembly, and heteroatom doping—to optimize the multifunctionality, biocompatibility, and targeting capabilities of CNMs at the nano-bio interface. We explore how engineered interfaces enable advanced applications in biosensing, stimuli-responsive drug delivery, multimodal bioimaging, antibacterial therapy, and regenerative tissue engineering. The review also addresses challenges such as scalability, long-term toxicity, and regulatory hurdles, and proposes future directions to expedite clinical adoption. By providing a comprehensive framework for rational surface design, this work aims to bridge the gap between fundamental materials science and clinical needs, offering a roadmap for developing next-generation carbon-based theranostics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4302-9
The pre-deposited lead iodide (PbI2) film in two-step inverted perovskite solar cells (PSCs) often exhibits a dense structure, which impedes the diffusion and reaction of organic ammonium salts, leading to unreacted PbI2 residues and compromised device performance. To address this, 2,4-oxazolidinedione (OD) is introduced as a molecule additive into the PbI2 precursor solution. Owing to its stronger coordination with PbI2, OD effectively modulates its crystallization behavior, resulting in a porous structure. This porous structure significantly facilitates the diffusion and infiltration of organic ammonium salts, thereby minimizing PbI2 residue and enhancing the completeness of the perovskite conversion. Furthermore, OD and the constructed porous network jointly retard the crystallization kinetics of perovskite, promoting the formation of perovskite films with improved crystallinity and preferred crystal orientation. Therefore, the optimized PSCs achieve a power conversion efficiency (PCE) of 26.31%, and demonstrate excellent operational stability, retaining 90.24% of initial PCE for 1500 h at 25°C and 90.47% after 1000 h at 65°C. The champion device exhibits a VOC of 1.197 V, a JSC of 26.28 mA cm-2, and an FF of 83.58%, with negligible hysteresis. This study presents a straightforward yet effective approach to advancing the performance and stability of inverted PSCs fabricated via the two-step method.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4271-5
Photocatalytic functional coatings are at a pivotal juncture where the primary research focus must transition from intrinsic material activity to a unified framework centered on surface serviceability. Surface serviceability encompasses the ability of a coating to maintain catalytic activity, interfacial integrity, multifunctional performance, safety, and manufacturability under specific service environments over its operational lifetime. Over the past three decades, photocatalytic surfaces have demonstrated potential for degrading organic pollutants, maintaining surface cleanliness, and enabling air purification, with applications in buildings, glass, highways, and infrastructure. However, high intrinsic activity alone does not guarantee stable long-term performance when the photocatalyst is immobilized as a substrate-integrated film. Performance is governed by coupled factors including interfacial adhesion, film structure, environmental aging, and functional durability. Current challenges extend beyond catalytic activity to include long-term deactivation, coating-substrate interfacial stability, trade-offs among multiple functions, adequacy of evaluation methods, and scalability of fabrication. These issues form a progressive service chain: design determines catalyst exposure and adhesion; environmental stresses induce functional or structural failure; multifunctional integration may compromise one function for another. Therefore, application-oriented evaluation is essential. This perspective advocates for a paradigm shift toward service-oriented design, requiring establishment of service-relevant evaluation protocols and development of scalable, repairable fabrication routes. Such efforts will enable photocatalytic coatings to evolve from high-activity laboratory materials into engineering surfaces that are verifiable, comparable, manufacturable, and durable in real-world applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4269-4
Self-assembled molecular interlayers (SAMs) are promising hole-selective contacts for high-efficiency organic solar cells (OSCs) due to their well-defined energy alignment and minimal parasitic absorption. However, their intrinsically limited mechanical robustness often leads to structural degradation and performance loss under mechanical deformation, restricting their application in flexible devices. Here, we report a nanoparticle-reinforced self-assembled composite interface that simultaneously enhances mechanical reliability and optoelectronic performance. Uniformly dispersed SiO2 nanoparticles are introduced as high-modulus reinforcing building blocks without disturbing molecular self-assembly. In contrast to NiOx nanoparticles, which suffer from aggregation and parasitic absorption, SiO2 nanoparticles exhibit excellent dispersion and optical transparency, enabling formation of a structurally compatible hybrid interface. Mechanistic studies reveal that SiO2 nanoparticles redistribute interfacial stress and form dynamic hydrogen-bond networks with phosphonic acid groups of 2PACz, providing efficient energy dissipation during cyclic deformation. Meanwhile, modulation of interfacial polarity extends the crystallization time window of the active layer, resulting in enhanced molecular ordering and improved charge transport. As a result, devices based on the SiO2/2PACz composite interface achieve a power conversion efficiency of 20.14% for rigid devices and 19.30% for flexible devices, placing the flexible devices among the highest-performing flexible OSCs reported to date, while retaining over 90% of their initial efficiency after repeated bending cycles. This work establishes a general strategy for overcoming the trade-off between electronic selectivity and mechanical robustness in ultrathin self-assembled molecular interfaces, providing design insights for high-performance flexible organic optoelectronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4300-3
The power conversion efficiency (PCE) of organic solar cells (OSCs) has surpassed 21% with the donor polymer D18, yet its processing from non-halogenated solvents like ortho-xylene (o-XY) remains inefficient due to uncontrolled film formation kinetics. Here, we systematically synthesize D18 polymers with molecular weights ranging from 41.6 kDa to 70.9 kDa to modulate crystallization kinetics. In-situ film drying studies reveal that lower molecular weights accelerate solidification, leading to excessive aggregation, while higher molecular weights slow it, causing insufficient phase separation. A medium molecular weight (D18-M) achieves a balanced crystallization rate, promoting favorable morphology and yielding a PCE of 20.55% with L8-BO as acceptor—one of the highest reported for non-halogenated solvent-processed OSCs. Energy loss analysis indicates that although low-molecular-weight polymers exhibit higher intrinsic luminescence, the blend film's emission is governed by exciton environment, which is dictated by morphology. This work underscores the critical role of molecular weight in controlling film formation and morphology, offering a simple yet effective strategy for high-efficiency, environmentally friendly OSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4323-8
Sulfur-based batteries are promising for next-generation energy storage due to high theoretical capacity, natural abundance, and low cost of sulfur cathodes. However, practical implementation is impeded by sluggish sulfur redox kinetics, dissolution and migration of intermediate polysulfides, and formation of insulating discharge products. Conventional catalyst design focuses on charge distribution, adsorption energetics, and structural confinement, yet these approaches incompletely describe the complex electronic processes governing sulfur conversion. Electron spin, an intrinsic quantum degree of freedom, offers an additional dimension for modulating catalytic behavior via its influence on electronic structure and orbital interactions at catalytic interfaces. In spin-polarized systems, changes in occupation and splitting of transition-metal d orbitals can regulate d-p hybridization with sulfur species, affecting interfacial charge transfer and energetics of sulfur redox reactions. This review summarizes recent progress in elucidating and manipulating electron spin in sulfur-based battery systems. Fundamental principles connecting spin states with electronic structure and catalytic behavior are outlined, followed by experimental approaches for probing spin-related electronic properties using spectroscopic and magnetic characterization techniques. Emerging strategies for spin regulation are highlighted, including heteroatom doping, defect engineering, coordination environment modulation, chirality-induced spin selectivity, and external magnetic-field control. Remaining challenges in identifying spin effects under realistic electrochemical conditions are addressed, along with opportunities for integrating spin-related descriptors into catalyst design. Establishing quantitative relationships between spin polarization, orbital hybridization, and sulfur reaction pathways may provide new perspectives for high-performance sulfur-based batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4246-5
Developing organic solar cells (OSCs) processable from green solvents without additives or post-treatments is essential for sustainable manufacturing, yet high power conversion efficiency (PCE) remains difficult due to limited morphology control. Herein, we develop a new electron-deficient building block, dithiazolo[4',5':3,4;5'',4'':5,6]benzo[1,2-d][1,2,3]triazole (DTzBT), which fuses benzo[d][1,2,3]triazole (BTA) with thiazole to leverage S/N-mediated non-covalent interactions, enhance planarity and lower the HOMO. To isolate side-chain effects, two DTzBT-based donors, namely PTzMe-F (N-methyl) and PTzEH-F (N-2-ethylhexyl), have been designed and synthesized. PTzMe-F exhibits poor solubility and miscibility with L8-BO, yielding 2.64% PCE (chloroform). PTzEH-F exhibits excellent processability and favorable morphology, delivering 17.61% PCE (chloroform) and 19.17% as-cast from toluene without any additive or post-treatments. In addition, the ternary LbL device based on PTzEH-F/L8-BO:PC71BM achieved an impressive efficiency of 20.27%. Comprehensive characterization indicates that 2-ethylhexyl side chains afford optimal solubility while preserving strong intermolecular interactions and favorable phase separation. DTzBT mitigates BTA’s HOMO-raising tendency via electron-withdrawing thiazole fusion, reconciling aggregation tunability with energy-level control. These results show that precise backbone and side-chain co-design enables green-solvent, additive-free processing for high-performance OSCs, advancing sustainable photovoltaic manufacturing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4340-0
Thin films with nonreciprocal circularly polarized luminescence (CPL) emit circularly polarized light with opposite handedness from its two opposite sides, holding great promise for advancing optical multiplexing technologies. Herein, we introduce component orientation mismatch into chiral composite films via stretching, which leads to macroscopic optical anisotropy and accordingly drives the films to show nonreciprocal CPL activity. Stretching triggers linear dichroism-linear birefringence (LD-LB) coupling to realize nonreciprocal circular dichroism (CD) in elastomer films consisting of thermoplastic polyurethane (TPU) and chiral polyacetylene (R/S-PSA). Moreover, fluorescence anisotropy-linear birefringence (f-LB) coupling occurs after introducing fluorescent groups into the films to achieve multi-color nonreciprocal CPL. The unstretched films exhibit reciprocal CPL with a luminescence dissymmetry factor (|glum|) of 10⁻¹, with handedness determined by PSA’s intrinsic helical chirality. In the stretched films, the oriented fluorescent groups undergo f-LB coupling with matrix crystallization, resulting in nonreciprocal CPL (|glum|=10⁻²). Based on this distinctive chiroptical feature, we have developed chiral logic gates, multidimensional optical encryption systems, and enantioselective photopolymerization platforms to demonstrate the potential uses of the as-obtained CPL films. This work provides both fundamental insights into and a versatile material platform for developing smart nonreciprocal photonic systems with advanced chiroptical functionality.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4349-9
Sodium metal batteries are promising for large-scale energy storage due to sodium's abundance and low cost, but their commercialization is hindered by dendrite growth and low utilization of sodium metal anodes. Here, we report a yolk-shell structure with gold nanoparticles (Au NPs) confined in hollow carbon nanospheres (Au@HCN) as a robust seeding/hosting interphase. The encapsulation isolates Au NPs from direct electrolyte contact, mitigating parasitic reactions, while the void space accommodates volume changes during alloying. Notably, electrochemical testing reveals that Au NPs undergo alloying-induced amorphization upon sodiation, forming a Na-Au amorphous alloy that enhances sodiophilicity and ensures uniform Na nucleation. This amorphous phase, confirmed by ex situ X-ray absorption spectroscopy and transmission electron microscopy, reduces nucleation overpotential and promotes dendrite-free deposition. The Au@HCN electrode achieves a high Coulombic efficiency of 99.8% over 500 cycles at 1 mA cm−2 and a long cycle life of over 2000 hours at 0.5 mA cm−2 in symmetric cells. Full cells paired with Na3V2(PO4)3 cathodes deliver a specific capacity of 105 mAh g−1 with 92% retention after 500 cycles. This work provides a rational design for stable sodium metal anodes through encapsulation and alloying-induced amorphization, offering a pathway for practical sodium metal batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4202-3
Carbon dots (CDs) with absorption in the second near-infrared window (NIR-II, 900-1700 nm) hold promise for tumor theranostics, yet existing synthesis methods often involve complex procedures, harsh conditions, or lack precise control. Here we report a 'self-photooxidation-restructuring' strategy that enables structural reorganization of the carbon core in CDs, achieving a significant redshift of absorption into the NIR-II region. Under ultraviolet (UV) light irradiation, the precursor (B-CDs, absorption in UV region) generates singlet oxygen, which self-oxidizes aldehyde groups and the carbon skeleton of B-CDs to stronger electron-withdrawing carboxyl groups and carbon radicals, respectively. These processes facilitate the formation of new C=C bonds between isolated aromatic domains, thereby transforming B-CDs into novel CDs (N-CDs) characterized by enhanced donor-acceptor interactions and a redshift in absorption toward the NIR-II window. Various experimental data, including high-resolution XPS, FTIR, NMR, EPR, have proved the proposed formation mechanism. The novel N-CDs afforded a high photothermal conversion efficiency of up to 71.33%, which enabled 1064 nm laser-activated photoacoustic imaging (PAI)-guided photothermal therapy (PTT) in tumors. This work opens a new avenue for the synthesis and modulation of CDs in the NIR-II region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4359-0
Organic solar cells (OSCs) require cathode interlayers (CILs) that combine high charge transport, defect passivation, and thickness insensitivity for scalable manufacturing. Here, we report the synthesis of a novel A-D-A-A'-type polymer, PDPP2F-NDI-N, via the green and efficient direct arylation polymerization (DArP) method. The multiple electron-deficient units in the backbone confer strong electron-withdrawing character, effective work function modulation, enhanced built-in potential, high crystallinity, and ordered molecular packing. PDPP2F-NDI-N exhibits a high electron mobility of 1.01 × 10⁻³ cm² V⁻¹ s⁻¹ and electrical conductivity of 3.13 × 10⁻³ S m⁻¹, facilitating efficient charge extraction and transport. Its interfacial modification capability suppresses interfacial defects and reduces non-radiative recombination losses. In ternary OSCs, PDPP2F-NDI-N achieves a high power conversion efficiency (PCE) of 20.44%, with outstanding thickness insensitivity retaining 92.8% of peak PCE at a 30 nm CIL thickness, and a T80 lifetime exceeding 1700 hours under photo-thermal aging. This work demonstrates that poly(A-D-A-alt-A') backbone design combined with DArP synthesis provides an effective strategy for developing high-performance, thickness-insensitive, and stable polymeric CILs, advancing efficient, stable, and scalable OSC applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4360-7
Polarization-sensitive photodetection is critical for advanced optical communication and imaging systems, yet conventional photodetectors suffer from low on-off ratios and limited polarization discrimination. Here, we report gate-tunable PdSe2/WSe2 van der Waals heterostructures that achieve ultrahigh light on-off ratio and polarization-sensitive photodetection. The heterostructure forms a type-II band alignment, enabling efficient charge separation and self-powered operation. By applying a gate voltage, the photoresponse can be modulated, achieving an on-off ratio exceeding 10^6 under illumination. The device exhibits a high responsivity of 1.2 A/W and a specific detectivity of 10^12 Jones at room temperature. Polarization-sensitive measurements reveal a linear dichroism ratio of 2.1 at 532 nm, attributed to the anisotropic crystal structure of PdSe2. The photodetector operates over a broad spectral range from visible to near-infrared (400-1000 nm) with fast response times (rise/fall < 100 μs). The gate-tunable capability allows dynamic control of the photocurrent, enabling adaptive sensing applications. These results demonstrate that PdSe2/WSe2 heterostructures are promising candidates for high-performance, polarization-sensitive photodetectors, offering a pathway for next-generation optoelectronic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4381-5
Bismuth telluride (Bi2Te3)-based alloys remain the benchmark for low-temperature thermoelectric applications, yet their conversion efficiency is limited by the trade-off between electrical and thermal transport. This study introduces a pseudo grain boundary engineering strategy to simultaneously enhance the average figure of merit (ZT) in p-type (Bi,Sb)2Te3 (BST) materials. By incorporating Ag-based compounds, the carrier concentration is optimized via substitution of Ag+ ions, while the introduction of secondary phases at grain boundaries effectively suppresses lattice thermal conductivity. The approach yields a peak ZT of 1.35 at 393 K and an average ZT of 1.25 across 303–483 K, representing a significant improvement over pristine BST. Compared to prior reports, this work achieves superior average ZT while maintaining high electrical conductivity, addressing the longstanding bottleneck of thermal conductivity reduction without compromising carrier mobility. The findings underscore the efficacy of pseudo grain boundary engineering in advancing Bi2Te3-based thermoelectrics for solid-state cooling and power generation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4367-4
Single-crystalline Cs3Cu2I5 has attracted considerable interest owing to its excellent scintillation performance and favorable stability. Nevertheless, second phases induced by peritectic reactions during melt growth give rise to deteriorated scintillation properties and promote crystal cracking. In this work, the effects of non-stoichiometric ratios of raw material (n(CsI)=0.57, 0.62, and 0.63) on the crystallization behavior and scintillation properties were systematically investigated. The results show that the crystal quality is optimal at n(CsI)=0.62, featuring high transparency, absence of macroscopic inclusions, and cracking free, with a PLQY of 79.3%. Temperature-dependent photoluminescence verifies the self-trapped exciton emission mechanism with strong exciton-phonon coupling, giving an exciton binding energy of 473.9 meV and a Huang-Rhys factor S of 79.8. The as-grown crystal exhibits an optimized light yield of 24,380 photons/MeV, an energy resolution of 3.8% for 137Cs (662 keV) γ-rays, a dominant decay time of 957 ns, and excellent linear response in the medium-to-high energy region. Precise regulation of the raw material stoichiometry can effectively suppress the formation of second phases, yielding high-quality Cs3Cu2I5 single crystals whose comprehensive performance demonstrates promising application potential in γ-ray detection.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4201-0
Open fracture fixation faces dual critical challenges: bacterial infection and impaired bone healing. This study presents a rationally designed biomacromolecular network coating (Ti-GOED) on titanium alloy bone plates to simultaneously address these issues. The coating integrates antimicrobial and osteogenic components, achieving an optimal balance between antibacterial efficacy and biocompatibility. In vitro assays demonstrated that Ti-GOED eliminates over 99% of common pathogenic bacteria by inhibiting peptidoglycan synthesis, disrupting bacterial cell wall formation, compromising membrane integrity, and leading to intracellular DNA leakage and bacterial death. Concurrently, Ti-GOED enhances the proliferation and osteogenic differentiation of bone marrow mesenchymal stem cells (BMSCs) via activation of the PI3K-Akt and HIF-1 signaling pathways. In vivo animal experiments confirmed strong antibacterial and osteogenic properties. This work provides a strategy for developing antibacterial coatings on medical devices, with significant potential for preventing and treating infections post-fracture fixation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4369-1
Sodium-ion batteries (SIBs) are promising alternatives to lithium-ion batteries for large-scale energy storage due to sodium's abundance and low cost. Among cathode materials, polyanionic compounds like Na3V2(PO4)2O2F (NVPOF) offer high energy density and dual voltage plateaus at ~3.6 and 4.0 V, but suffer from low electronic conductivity and sluggish Na+ diffusion. Here, we report a dual-modulation strategy combining high-valence Nb5+ doping and polydopamine-derived carbon coating to synthesize Na3V1.94Nb0.06(PO4)2O2F-C (NVPOF-Nb-C) via a hydrothermal route. X-ray diffraction and Rietveld refinement confirm that Nb5+ doping induces slight lattice expansion without altering the tetragonal I4/mmm framework. Density functional theory calculations reveal that Nb5+ doping optimizes the crystal structure and reduces the Na+ diffusion barrier, while the uniform carbon coating enhances electron transport. Consequently, NVPOF-Nb-C exhibits remarkably improved electrochemical performance, including high reversible capacity, excellent rate capability, and ultralong cycling stability. In a full cell with hard carbon anode, it delivers a high energy density of 487.2 Wh kg−1 at 1C and retains 91.51% capacity after 3000 cycles at 20C. This work provides a synergistic strategy to overcome the intrinsic limitations of polyanionic cathodes for practical SIB applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4262-7
The escalating demands of artificial intelligence, machine learning, and neural computing necessitate multifunctional optoelectronic devices capable of integrating sensing, memory, and processing. Two-dimensional van der Waals heterostructures (vdWHs) offer unique advantages, yet their practical deployment is hindered by complex architectures and inefficient mode-switching. Here, we demonstrate a MoTe2/SnS2 anti-ambipolar heterojunction device enabling single-gate reconfiguration among frequency doubling, broadband photodetection, and neuromorphic computing. The device exhibits a peak-to-valley ratio (PVR) of 465, ensuring efficient frequency doubling. As a photodetector, it operates across an exceptionally broad spectral range of 520–2200 nm, with outstanding responsivity and detectivity. Furthermore, the device emulates complete synaptic behaviors, including short-term plasticity (STP), long-term plasticity (LTP), and paired-pulse facilitation (PPF). Integrated into a reservoir computing (RC) system trained on a vehicle motion dataset, it achieves a directional recognition accuracy of 98.7%. This work establishes a paradigm for multifunctional integration and low-power neuromorphic computing, advancing next-generation intelligent optoelectronic systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4206-6
Precise patterning of highly ordered organic semiconductor (OSC) thin-film arrays is critical for next-generation electronics. We report a ladder-like polysilsesquioxane (LPSQ) strategy to synthesize two functional analogs with tunable surface energies and robust dielectric properties. These LPSQ dielectrics, functionalized with alkyl or fluoroalkyl side chains, serve dual roles as gate insulators and patterning layers to guide blade-coating of 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT). This approach yields highly aligned arrays suitable for three-dimensional integration in flexible electronics. Synergistic combination of dense LPSQ dielectric packing and aligned semiconductor domains leads to excellent organic thin-film transistor (OTFT) performance, achieving approximately four-fold improvement in field-effect mobility compared to conventional silicon oxide dielectrics. Patterned LPSQ dielectrics enable high-resolution C8-BTBT patterning on plastic substrates, supporting 4-inch-scale 3D integration of flexible logic circuits, including inverters (voltage gain >100), NOR gates, and NAND gates. This work provides a scalable route to high-performance, large-area flexible organic circuits.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4315-2
High-temperature X-ray imaging demands scintillators with high crystallinity, efficient scintillation, and robust thermal stability, yet suitable materials remain scarce. Here, we report an ultra-high-crystallinity transparent glass-ceramic (GC) scintillator strategically designed via controllable heat-treatment-induced crystallization. A sequential precipitation method is employed, where cubic CaF2 nanocrystals initially form, subsequently promoting heterogeneous nucleation and growth of hexagonal BaAl2Si2O8. Intrinsic nanoscale phase separation into F-rich and O-rich domains significantly reduces atomic diffusion distances, yielding an unprecedented crystallinity of up to 97.6%. Notably, defect traps (oxygen vacancy defects, likely located within the lattice or at crystalline/amorphous interfaces) enable efficient carrier capture and thermally stimulated release, contributing to remarkable resistance to thermal quenching. Consequently, the GC scintillator maintains 90.6% of its integrated X-ray excited luminescence (XEL) intensity at 300 °C, with the integrated XEL intensity reaching 94.2% of commercial Bi4Ge3O12 (BGO) at room temperature. This enables stable high-temperature X-ray imaging with a spatial resolution of ~10.4 lp mm−1 up to 225 °C. This work provides a versatile pathway for developing high-sensitivity scintillators for extreme-environment X-ray imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4236-8
Electrochemical nitrate reduction (NO3RR) to ammonia offers a sustainable route for nitrogen recovery from wastewater, yet its efficiency is constrained by complex multi-step proton-electron transfers and competitive hydrogen evolution. Here, we report a series of binary cobalt-copper phosphates with precisely tuned Co/Cu ratios, revealing a volcano-type relationship between composition and catalytic activity. The optimized Co0.5Cu1.5(OH)PO4 catalyst, supported on a Ni3Co1OxHy/Ni foam substrate, achieves a Faradaic efficiency of 99.0% for ammonia at a high current density of 200 mA cm−2 in 1 M nitrate electrolyte, with a production rate of 9.18 mg h−1 cm−2 and sustained stability over 200 hours. In-situ ATR-FTIR spectroscopy and density functional theory calculations elucidate a tandem mechanism: Co sites promote water dissociation to generate active hydrogen (H*), while adjacent Cu sites facilitate nitrate adsorption and subsequent hydrogenation steps. This synergistic division of labor lowers the energy barrier for the rate-determining step, effectively suppressing HER and enhancing intrinsic kinetics. The work demonstrates that precise atomic-ratio engineering in dual-site transition metal phosphates provides a viable strategy to overcome activity-selectivity trade-offs in electrocatalytic nitrate-to-ammonia conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4176-y
Three-photon microscopy (3PM) in the near-infrared-III (NIR-III) window (1600–1840 nm) enables high-resolution visualization of cerebral vasculature in vivo, but its imaging depth and quality are limited by the performance of fluorescent probes. Here, we report a probe optimization strategy transitioning from mirror symmetry to centrosymmetry, yielding a highly symmetric aggregation-induced emission (AIE) molecule, T4PQ. The centrosymmetric structure aligns donor-acceptor units, promoting uniform electron cloud delocalization and directional charge transfer, which enhances exciton formation and suppresses non-radiative decay, thereby increasing fluorescence quantum yield. This symmetry also boosts the three-photon absorption cross-section by enhancing electron delocalization and transition dipole moment, enabling stronger nonlinear optical responses under long-wavelength excitation. T4PQ nanoparticles (T4PQ NPs) exhibit an enhanced three-photon absorption cross-section, high fluorescence quantum yield, and excellent photostability. In murine models, T4PQ NPs achieved three-dimensional cerebrovascular imaging at a depth of 1785 μm and real-time hemodynamic observation in microvessels at 1006 μm depth, with good biocompatibility. These results validate the advantage of centrosymmetric molecular design for deep-brain imaging probes, offering a high-performance tool for neurovascular research.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4113-3
Constructing abundant grain boundary defects is a promising strategy for developing high-efficiency catalysts. However, achieving dense grain boundary defects in CuO and Cu at the nanoscale remains challenging. Inspired by Turing patterns in nature, a Turing-type CuO catalyst (TGB-CuO) with abundant grain boundaries at ~10 nm nanoscale was prepared by annealing a dodecyl sulfate-intercalated basic copper carbonate. The balanced diffusion-reaction dynamics during pyrolysis drove the spontaneous formation of Turing-type grain boundary architectures in TGB-CuO. The resulting TGB-CuO electrode exhibited outstanding performance in electrochemical CO2 reduction (ECO2RR), delivering a Faradaic efficiency of 80.15% toward multi-carbon (C2+) products and maintaining over 50% ethylene selectivity at 300 mA cm−2 for 30 h of continuous operation. Activity investigations indicated that the metallic Cu retaining Turing-type grain boundary features (TGB-Cu) formed during electroreduction was responsible for the enhanced ECO2RR performance. The Cu(100)/(100), Cu(100)/(111), and Cu(111)/(111) grain boundaries promoted CO2 activation and *CO adsorption, while lowering the free energy barriers for the rate-determining *CO2− → *COOH step and C–C coupling step. This bioinspired reaction-diffusion strategy offers a new paradigm for creating high-density grain boundary defects, offering a general route toward efficient catalyst design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4277-1
Two-dimensional (2D) magnetic materials hold promise for next-generation spintronics, yet most exhibit Curie temperatures (Tc) far below room temperature, limiting practical applications. Here, we report the realization of room-temperature ferromagnetism in CuCrSe2 nanosheets via controlled anion removal achieved by post-synthetic vacuum annealing. Raw CuCrSe2 shows a low Tc of ~120 K, whereas annealed CuCrSe2 (A-CuCrSe2) nanosheets exhibit robust ferromagnetic ordering above 300 K. Structural and compositional analyses, including transmission electron microscopy, Raman spectroscopy, and X-ray absorption spectroscopy, confirm that A-CuCrSe2 retains the original layered crystal structure with an estimated Se vacancy concentration of approximately 10%. Magnetic measurements reveal room-temperature ferromagnetism in exfoliated nanosheets, corroborated by magnetic imaging and electric transport measurements. Anomalous Hall effect (AHE) measurements uncover the coexistence of two ferromagnetic phases within the same sample: one with low Tc (~120 K) and another with high Tc (>300 K), indicating spatially heterogeneous magnetic ordering driven by anion removal distribution. Density functional theory (DFT) calculations elucidate the microscopic mechanism, suggesting that Se vacancies modulate the magnetic exchange interactions, enhancing Tc. This work demonstrates that anion modulation is an effective intrinsic strategy to achieve room-temperature ferromagnetism in 2D materials, potentially advancing spintronic applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4159-y
The electrocatalytic oxidation of ethylene glycol (EG) derived from polyethylene terephthalate (PET) waste to valuable glycolic acid (GA) represents an attractive route for waste resource upcycling. However, achieving high selectivity remains challenging due to the difficulty in steering the complex reaction pathway. In this study, PdPtCuInBi high-entropy intermetallic metallene (HEI-PdPtCuInBiene) is reported to precisely control EG oxidation reaction (EGOR) pathway for GA production by constructing multiple active sites at the atomic scale. In PET hydrolysate, it achieves a Faradaic efficiency of 99.87% and a production rate of 1.47 mmol h−1 cm−2, along with excellent stability. Mechanistic studies reveal that the high-entropy structure induces strong p-d orbital hybridization, which optimizes the electronic structure of active sites, thus weakening the adsorption of key carbonyl intermediates and suppressing C–C bond cleavage. The synergistic electronic effect among Pd, Pt, and Cu further enables differential adsorption of distinct intermediates on diverse active sites, enhancing the selective formation of GA. Techno-economic analysis exhibits high profitability (~$784.9 t−1 PET) of this route, demonstrating the great potential of high-entropy intermetallic metallene in regulating electrocatalytic upcycling of PET waste and beyond.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4234-3
The pursuit of high-energy-density sodium-ion batteries (SIBs) necessitates the development of stable high-capacity anodes. While amorphous carbon is a promising anode candidate for SIBs, its practical application is hindered by limited capacity. Herein, we design a composite anode by chemically confining a high-content (~25 wt%) short-chain sulfur into hierarchical porous hard carbon microspheres (SHHC) derived from microbe yeast. The SHHC anode exhibits a high reversible capacity of ~807 mAh g−1 at 0.03 A g−1 (~3 times that of conventional amorphous carbon) along with superior rate capability, and extraordinary long-term cyclability (almost 100% capacity retention after 2000 cycles at 1.0 A g−1). The high-content sulfur species contribute to superb redox reactivity for high-capacity sodium storage via a surface-dominated storage mechanism. The carbon matrix features an enlarged interlayer distance, which facilitates Na-ion intercalation and deintercalation for high-rate capability. Furthermore, the hierarchical porous structure with built-in cavities facilitates the Na-ion transfer and effectively accommodates the electrode’s volume expansion, achieving fast electrode kinetics and outstanding cyclability. Such a combination of favored properties leads to state-of-the-art comprehensive battery performance for Na-ion storage. Our finding envisions a new perspective on building stable high-capacity anode materials for SIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4192-y
Electrochemical water splitting is pivotal for scalable green hydrogen production, yet its practical deployment hinges on cost-effective electrocatalysts with high activity and durability. This study introduces a low-cost, three-dimensional (3D) nanoporous ZrVFeCoNi material fabricated via chemical dealloying, at merely 0.16% of the cost of Pt. The structure-activity relationship between its microstructure and hydrogen evolution reaction (HER) performance was systematically explored. Lattice defect effects from multiphase intermetallic compounds, combined with multi-metal synergy, optimize H+ adsorption energy and electron transfer kinetics. The 3D nanoporous architecture provides a high electrochemical surface area with abundant active sites, enhancing electrolyte penetration and reducing interfacial mass transfer resistance. Consequently, the ZrVFeCoNi electrode exhibits outstanding HER performance, requiring only a 38 mV overpotential to reach 10 mA cm−2 and maintaining stable operation for 1000 h at 500 mA cm−2. Integrated into a full water electrolyzer (ZrVFeCoNi || IrO2/Ni), the system achieves a cell voltage of 1.60 V at a current density of 400 mA cm−2. Advanced characterization and density functional theory (DFT) calculations reveal that interfacial interactions and charge transfer at heterointerfaces drive catalytic activity, showcasing the potential of 3D nano-structured multiphase intermetallic compounds as high-performance electrocatalysts for green hydrogen systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4257-y
Hafnia-based ferroelectrics exhibit a distinctive reverse size effect and exceptional scalability, positioning them as critical candidates for CMOS-compatible non-volatile memory and ferroelectric transistors, with substantial promise for advancing hardware acceleration in artificial intelligence and large-data storage technologies. However, their practical deployment is constrained by a longstanding dilemma: the difficulty in simultaneously stabilizing metastable polar phases and ensuring long-term reliability under the high electric fields required for polarization switching. This review reinterprets this challenge through the lens of defect physics and advocates a paradigm shift from stochastic, disorder-mediated defect incorporation toward ordered, multiscale defect engineering. We systematically discuss the collective influence of point defects, line defects, planar defects, and defect-coupled structures on the phase stability, switching kinetics, and failure mechanisms in hafnia-based ferroelectrics. Controlling oxygen-vacancy states, engineering dopants via Fermi-level and chemical pressure, deploying periodic dislocation arrays, designing topological domain walls, functionalizing interfaces, and leveraging flexoelectric strain gradients constitute the core strategic toolkit. Through such ordered defect architectures, scalable performance metrics, including high remanent polarization, low coercive field, fast switching speed, and endurance exceeding 10^12 cycles, become attainable. These approaches establish a set of design principles for next-generation low-power, high-reliability ferroelectric electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4317-4
This correction addresses an image assembly error identified in Fig. 7a of the original article published in Science China Materials, volume 66, issue 6, 2023, pages 2513–2522. The error was confined to the assembly of images in Fig. 7a, which presents H&E staining analysis of major organs from a toxicity study. The corrected version of Fig. 7 is provided in this corrigendum. The original study evaluated the toxicity of lyophilized cabazitaxel (CTX) and Tween 80-based CTX formulations in CD-1 mice following a single intravenous administration of 30 mg kg−1 CTX via the tail vein on day 0, with sacrifice on day 14 for analysis (n=5). The figure includes H&E staining of major organs, complete blood count (CBC) analysis with statistical significance indicated by *p < 0.05, and mouse weight measurements. The correction does not affect the overall results, data interpretation, or scientific conclusions of the original article. All authors have reviewed and approved the content of this corrigendum. The authors sincerely apologize for any inconvenience caused to the editorial office, reviewers, and readers. The article was received on 6 May 2026, accepted on 4 June 2026, and published online on 31 July 2026.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4200-0
Self-powered broadband photodetectors are pivotal for next-generation intelligent healthcare. Solution-processed mercury sulfide (HgS) is an attractive near-infrared absorber but is limited by interfacial instability, high defects, and sluggish response. Inspired by sulfur-mediated adhesion in Alhagi sparsifolia, a bioinspired interfacial engineering strategy employs an antimony sulfide (Sb2S3) interlayer to construct a bidirectional chemical bonding network. The Sb2S3 interlayer simultaneously forms Sb–O bonds with fluorine-doped tin oxide (FTO) substrates and Sb–S/Hg–S bonds with the HgS layer, thereby reinforcing interfacial adhesion, passivating coordination-unsaturated defect states, and establishing a type-II heterojunction with a strong built-in electric field. The resulting Sb2S3/HgS photodetector exhibits self-powered operation, broadband sensitivity spanning the visible to near-infrared region (642–1550 nm), an ultrafast response time of 2.47 ms, a detectivity up to 1.7 × 10^11 Jones, and retaining nearly constant photocurrent over 5000 continuous on-off switching cycles as well as prolonged air exposure. Beyond device-level performance, we demonstrate its utility in intelligent healthcare scenarios, including machine-learning-assisted liquid drug identification, binary-coded optical wireless communication, and high-fidelity photoplethysmography monitoring. This work establishes biomimetic bidirectional bonding as a generalizable paradigm for stabilizing solution-processed chalcogenide optoelectronics and accelerates the integration of self-powered broadband photodetectors into intelligent healthcare systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4322-4
Ultrafast scintillators with low-nanosecond emission are essential for next-generation high-rate X-ray and particle imaging. Although Ce3+-activated scintillators inherently exhibit fast response characteristics, conventional Ce3+-doped hosts rarely achieve low-nanosecond ultrafast decay. Here, we report a high-entropy fluoride scintillator (HEFS), Ce:LaGdCaSrBaF12 (Ce:LGCSB), in the form of bulk single crystals. The severe lattice distortion arising from multi-cation disorder induces exciton localization and effectively suppresses exciton diffusion. Through the rapid relaxation of localized excitons, the high-entropy Ce:LGCSB single crystals deliver a decay time of 1.23 ns with a 94.6% fast-component contribution and without any noticeable slow component. Through first-principles calculations, spectroscopic characterization, and transient dynamics analysis, we reveal that the ultrafast response originates from accelerated Frenkel exciton (FE) recombination enabled by the high-entropy environment. This work establishes entropy-engineered fluorides as promising ultrafast scintillator platforms and proposes a general strategy for extending sluggish diffusion effects to the excitonic scale, offering new opportunities for improving scintillation timing performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4232-1
Polyanionic cathode materials are widely considered as potential cathode materials for sodium-ion batteries due to their strong three-dimensional framework and intrinsic thermal safety. Nevertheless, the limitation of the specific capacity and energy density hindered their application, which can be ascribed to the common reliance of single-electron redox reaction of the transition metal. By realizing the reversible double redox reaction of vanadium-based and manganese-based polyanion cathodes, researchers have successfully opened up a new way to break through the long-term performance limitations. Recent studies disclose that vanadium and manganese-based polyanionic cathodes exhibit the possibility of realizing a reversible double-redox reaction, which opened up new avenues to overcome the capacity dilemma. However, many fundamental issues remain unclear, including insufficient structural stability at high operating voltages, irreversible structural evolution induced by sodium extraction, sluggish electronic and ionic transport kinetics, and Jahn–Teller distortion. Therefore, it is imperative to summarize recent work in order to clarify the pathway for future investigation. In this review, the key challenges associated with the activation of the double-redox reaction are outlined, followed by the realization and regulation of the double-redox reaction in polyanionic cathode materials. A systematic summary of recent studies is performed for both vanadium and manganese-based compounds, which could contribute to the fundamental understanding of the double-redox reaction mechanism. Combined with the modification strategy and future perspective, this review provides insights into the rational design of polyanionic cathodes with a reversible double-redox reaction. It also offers insights into the development of high-energy-density cathode materials for next-generation sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4255-5
Localized overheating in high-rate lithium-ion batteries (LIBs) or lithium metal batteries (LMBs) accelerates dendrite formation, disrupting current density and thermal distribution uniformity. This study constructs a Janus-structured, polybenzimidazole (PBI)-welded separator (JNS@PBI) with polypropylene nanofibers (PPNFs) on one face and nanoscale carbon black-modified PPNFs (CPPNFs) on the other. The CPPNFs layer provides electronic conductivity to homogenize interfacial current distribution and heat dissipation, while the PPNFs layer ensures electronic insulation. PBI, serving as a welding agent with intrinsic ionic conductivity, enhances mechanical properties and lithium-ion transport. This design enables synergistic transport of ions and electrons at the JNS@PBI/SEI interface. Density functional theory (DFT) calculations elucidate how JNS@PBI enhances interfacial ion transport and regulates lithium deposition. JNS@PBI exhibits high porosity (71.3%), superior electrolyte uptake (451%), and high ionic conductivity (1.80 mS cm−1). Electrochemical tests confirm exceptional interfacial stability, with stable polarization voltage over 2000 h of plating/stripping cycles. Remarkable rate capability and cycling endurance are observed: high-capacity retention rates of 85.2% after 700 cycles at 1 C and 90.3% after 1500 cycles at 3 C in assembled LiFePO4/graphite full cells. This work provides a promising approach for next-generation separators for high-safety LIBs or LMBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4166-5
Oxygen evolution reaction (OER) represents a significant kinetic bottleneck in sustainable energy conversion due to its complex multi-step electron transfer process. Spin manipulation has recently emerged as a promising strategy to overcome traditional catalytic scaling relationships. However, the commonly used ferromagnetic materials or external magnetic fields suffer from practical limitations including material constraints and high energy consumption. The chiral-induced spin selectivity (CISS) effect in chiral inorganic nanomaterials with high stability, conductivity, and exceptional chiroptical properties offers a groundbreaking alternative by enabling spin polarization without the need for external magnetic fields. This review systematically examines the application of chiral inorganic nanomaterials for improving OER efficiency via the CISS effect. The fundamental principles of CISS and its influence on OER kinetics are discussed. Recent experimental advances highlighting the enhanced catalytic performance are analyzed. Future research directions and challenges in leveraging chirality and spin as key design principles for next-generation OER electrocatalysts are highlighted.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3696-3
The development of substitutable meniscus implants that can effectively protect articular cartilage remains a great challenge. Herein, a polyurethane with chemical crosslinking and sulfobetaine extenders containing hydrophobic chains (PU-CL-hSB) is developed, which could improve comprehensive properties and long-term stability simultaneously. By regulating the mole ratio of functional groups, PU-CL-hSB with appropriate mechanical properties, excellent tribological properties, and good fatigue resistance is used to prepare substitutable meniscus implant by hot-pressing. Due to the synergistic effect of functional groups, PU-CL-hSB meniscus implant presents comparable or even superior properties to native meniscus. It withstands a maximum force of 26.08 N versus 25.14 N for native meniscus, an energy dissipation from 45.93 to 39.17 N mm compared to 28.83 to 19.11 N mm for native meniscus over 300 cycles, and a friction coefficient from 0.08 to 0.19 compared to 0.11 to 0.26 for native meniscus. This PU-CL-hSB meniscus implant is further implanted into live rabbit knee joints for 8 and 25 weeks by a new approach, and in vivo data indicate that PU-CL-hSB meniscus implant not only protects articular cartilage from severe damage without eliciting inflammatory responses, but also can maintain normal physiological activities in the native state. Our findings present a substitutable meniscus implant that could be applied in vivo and propose evaluation methodologies for meniscus implants.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4114-5
The precise and controllable synthesis of one-dimensional (1D) and two-dimensional (2D) heterostructures, coupled with the manipulation of their atomic and electronic configurations, is of paramount significance. However, due to the synthetic challenges associated with graphyne (GY) materials, their integration into 1D/2D heterostructures remains considerably difficult. Herein, we demonstrate a post-synthetic intercalation strategy for tellurium onto Ag(111), enabling the controllable fabrication of 1D-GY-nanowire/2D-AgTe-monolayers heterostructures. Scanning-probe microscopies are employed to characterize morphological evolution during the intercalation process. Scanning tunneling spectroscopy results confirm that AgTe monolayer intercalation induces interfacial decoupling of the graphyne nanowires. Density functional theory calculations demonstrate that work function-driven Fermi level modulation via interfacial charge engineering assigns the 1D-GY-nanowire/2D-AgTe-monolayers heterostructures as type-I heterostructures. Our work not only significantly advances the fundamental understanding of interfacial interactions in 1D/2D heterostructures but also presents a scalable strategy for designing heterostructures with tailored electronic functionalities, thereby opening new avenues for applications in advanced nanoelectronics and optoelectronic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4213-x
Lipid peroxyl radicals (ROO·) are terminal propagating species in lipid peroxidation, driving oxidative damage in neurological disorders. Their prolonged lifetime and rapid diffusion within lipid membranes render them difficult to neutralize. Here, we report a bioelectric-responsive TEMPO-doped polydopamine (PDA@TEMPO) nanozyme that sustains catalytic interception of ROO· radicals under persistent oxidative stress. By coupling a PDA redox reservoir with TEMPO catalytic centers, the nanozyme establishes a self-regenerating radical-neutralization cycle via proton-coupled electron transfer (PCET). The π-conjugated framework facilitates charge migration and enables an electric-field-enhanced antioxidant response. In a seizure model, the nanozyme dynamically responds to bioelectric fluctuations, accelerating radical interception and alleviating oxidative stress in neural microenvironments. These findings establish bioelectric-coupled nanozymes as a general strategy for catalytic and sustained regulation of oxidative stress in neural microenvironments, providing a potential therapeutic approach for neurological disorders.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4258-0
High-entropy noble-metal-based catalysts (HENCs) have emerged as a frontier in electrocatalysis, leveraging the synergistic effects of high-entropy alloys and noble metals to achieve exceptional atomic utilization, tunable electronic structures, and vast compositional space. Their anisotropic architectures confer superior dissolution resistance, rapid electron/mass transfer, and abundant active sites. This review systematically categorizes advanced structural regulations—grain boundary engineering, single-atom alloys, intermetallic compounds, amorphous structures, and core@shell configurations—and evaluates their impact on electrocatalytic performance. By modulating surface electronic states and lattice strain, these strategies optimize reaction kinetics and durability. Notable applications include oxygen reduction (ORR), oxygen evolution (OER), hydrogen evolution (HER), and CO2 reduction (CO2RR). Despite progress, challenges persist in scalable synthesis, mechanistic understanding, and long-term stability. This review underscores the potential of HENCs to bridge laboratory innovation and industrial deployment, providing a roadmap for future catalyst design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4110-9
Flexible tactile sensors are pivotal for human-machine interaction, yet accurate decoupled sensing of three-dimensional (3D) forces and integration into functional systems remain challenging. Here, we present a piezoresistive 3D force sensor based on ionic hydrogels that detects and analyzes multi-directional forces. The sensor exhibits a linear response to normal forces from 1 to 25 N (R²=0.99) and maintains stable sensitivity for shear forces within 0–4 N. By incorporating both force magnitude and direction, the sensor enables multidimensional password input, expanding traditional one-dimensional passwords into numeric, alphabetic, and Morse code formats. Experimental results demonstrate significant potential for enhancing information security. The sensor's simple structure, mature fabrication, and ease of integration with flexible electronics underscore its practicality. This work addresses the bottleneck of unidirectional sensing in conventional flexible pressure sensors, offering a robust solution for multidimensional force acquisition in human-machine interfaces, soft robotics, and biomechanical monitoring.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3629-3
Electrically pumped lasers with reduced physical dimensions are critical for future optical information processing, storage, and photonic integrated circuits. However, electrical injection in perovskite lasers faces challenges including material instability, non-radiative losses, and Joule heating. Here, we demonstrate an ultralow-threshold perovskite microlaser decorated with gold nanoparticles (AuNPs), enabling simultaneous optical pumping and current injection at ambient temperature. The lasing threshold is reduced to 8.6 μJ/cm², approximately 44% lower than that of pristine devices (15.3 μJ/cm²). The AuNPs, with optimized size, enhance both lasing performance and electrical properties, achieving a current injection density of 2.98 kA/cm². AuNPs accelerate hot-carrier cooling, reducing non-radiative recombination and mitigating Joule heating. The threshold decreases progressively with increasing electrical assist fraction. Stability tests confirm excellent resistance to aging and humidity, with stable lasing output under co-excitation in ambient air. This work underscores the feasibility of electrically driven perovskite microlasers, offering a pathway toward electrically pumped microlaser diodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3608-8
Polymeric carbon nitride (PCN) is a promising photocatalyst for H2O2 production due to its visible-light response, low cost, and high selectivity for the two-electron oxygen reduction reaction (ORR). However, its H2O2 yield is limited by narrow light absorption, low charge separation efficiency, and insufficient active sites. Here, crystalline poly(heptazine imide) (PHI)-based carbon nitride with highly dispersed In sites and N defects was prepared via an ionothermal method using LiCl/KCl molten salts. The large π-conjugated system and N defects enhance visible-light harvesting. Remaining K+ ions in nitrogen cavities act as interlayer electron channels, while N defects induce asymmetric charge distribution on the heptazine network, promoting interlayer and in-plane charge separation and transfer. In sites accelerate charge transfer dynamics and serve as active sites for ORR. The synergistic effect of metal modification and defect engineering boosts electron delocalization, significantly improving photocatalytic activity. The H2O2 production rate of 10InPHI reaches 15.3 mmol g−1 h−1 via a two-step single-electron ORR pathway, underscoring the potential of modified carbon nitride for efficient H2O2 photosynthesis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3579-8
Metal sulfides such as CdS are promising for solar-driven H2O2 production but suffer from rapid charge recombination and severe photocorrosion. This study introduces a dual-functional strategy synergizing sulfur vacancy (Sv) engineering and polydopamine (PDA) coating to overcome these limitations. Sv-CdS nanorods were hydrothermally synthesized with tunable vacancy concentrations, followed by in-situ PDA deposition to construct a direct Z-scheme heterojunction. X-ray photoelectron spectroscopy (XPS) and density functional theory (DFT) calculations reveal that the introduction of S vacancies reduces the work function of CdS, facilitating energy level alignment with PDA and enabling efficient electron transfer from CdS to PDA. By tuning the concentration of S vacancies, the charge transfer efficiency can be maximized. As a result, the photocatalytic H2O2 production rate reaches 2539.5 μmol g−1 h−1 under visible light, and further increases to 4395.5 μmol g−1 h−1 after PDA encapsulation—15.6 times higher than that of pristine CdS. Concurrently, PDA enhances O2 adsorption and protects Sv-CdS from photocorrosion. Sv-CdS@PDA exhibited superior photostability compared to Sv-CdS after three consecutive photocatalytic cycles. Mechanistic studies suggest that the Z-scheme heterojunction effectively separates electron-hole pairs: electrons in the conduction band of CdS reduce O2 to ·O2−, which is subsequently converted to H2O2, while holes in the valence band of Sv-CdS oxidize water to replenish O2. This work provides fundamental insights into engineering charge transfer and stability in sulfide-based photocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3700-7
Photocatalytic synthesis has been considered a promising technology for solar-to-chemicals conversion. Here, a series of novel photocatalysts was synthesized by decorating uranyl sites on imine-based covalent organic frameworks (i-COF) and proved functioning for the uniformly boosted H2O2 production by 1.6–10.1 folds compared with the bare i-COFs in a wide pH range from 2 to 11. Typically, an optimal H2O2 production rate of 1435.9 μmol g−1 h−1, i.e., 28.72 mmol g(U)−1 h−1, was realized over uranyl decorated TTa-COFs under visible light. Systematic investigations reveal that the universally and remarkably promoted performance is attributed to the outstanding electron-transfer ability, accelerated activation of molecular oxygen and favored formation of ·O2− and *OOH as the key intermediate by virtue of the decorated uranyl ions; thus the two-step single-electron oxygen reduction reaction (ORR) for H2O2 photo-generation is significantly facilitated. This work paves a new way for the uranyl-decorated COFs as a novel photocatalyst and provides in-depth insight to the reaction mechanism for photocatalytic H2O2 production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3848-7
Conventional heterogeneous photocatalysts often suffer from insufficient light absorption, rapid charge recombination, and a lack of specific reactive sites for efficient photocatalytic oxidation. To overcome these limitations, we propose a molecular polarization engineering approach utilizing structurally well-defined donor (D)-acceptor (A) covalent triazine frameworks (CTFs). The construction of dipole-induced built-in electric fields within the D-A-structured CTFs enables enhanced exciton dissociation and facilitates directional charge transfer. Specifically, the asymmetric A1-D-A2 moiety enhances molecular polarization in the dual-acceptor system CTF-TBT (A1-D-A2), enabling efficient charge separation through multiple electron-withdrawing units. This structural design promotes directional electron transfer toward the secondary acceptor (benzothiazole, A2), while simultaneously concentrating holes on the donor unit. Consequently, the A2 moiety acts as a site for efficient O2 activation via electron accumulation, whereas the highly oxidized donor unit provides strongly positive holes (h+) that facilitate substrate oxidation. Experimental and DFT calculation results confirm that CTF-TBT demonstrates highly enhanced photocatalytic oxidation performance, which can be attributed to its multi-channel charge separation mechanism and spatially separated redox-active sites. This study highlights the effectiveness of molecular dipole engineering in designing heterogeneous photocatalysts with controlled charge transfer pathways and improved redox capabilities. The proposed design principles provide a universal approach for promoting solar-driven chemical synthesis applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3558-4
The development of advanced titanium alloys capable of operating above 600 °C remains a critical challenge for aerospace propulsion systems, where conventional Ti alloys suffer from insufficient high-temperature strength and microstructural instability. Here, we propose a computationally driven design strategy for titanium-based medium-entropy alloys (MEAs) that integrates thermodynamic phase prediction with mechanistically informed strength modeling, enabling systematic exploration of the Ti-Nb-Al-Cr quaternary system. The optimized Ti70Nb10Al15Cr5 MEA exhibits exceptional performance metrics: 18% room-temperature ductility (as-cast), a yield strength of 520.7 MPa at 650 °C (post-aging), and an ultralow density of 4.76 g/cm3 (45% lighter than Inconel 718). Microstructural characterization reveals a metastable single-phase BCC structure in the as-cast state, which transforms into a BCC/Ti3Al dual-phase system upon aging, with temperature-dependent precipitate morphology and phase stability. The alloy demonstrates superior high-temperature strength retention up to 900 °C (>80 MPa yield strength), outperforming commercial titanium alloys (e.g., Ti-1100, TG6) and bridging the performance gap between conventional Ti alloys and nickel-based superalloys. This work establishes a multi-criteria design paradigm for entropy-engineered alloys, offering a viable pathway to lightweight, high-temperature structural materials for next-generation aerospace applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3660-5
High-sensitivity piezoelectric ceramics with high piezoelectric constants (d33) are crucial for miniaturized, low-power, and high-efficiency transducers. However, conventional performance enhancement relies on intrinsic parameter modulation, which is limited and blind. This study introduces a performance-driven metamaterials creation model to develop structure-function-integrated piezoelectric materials. We systematically investigated the effects of metastructure design on d33 across two-dimensional straight rod (SR) structures, three-dimensional dot-matrix (Octa) structures, complex triply periodic minimal surface (TPMS) structures, and hybrid Octa&SR structures. The results demonstrate that metastructures combining high polarization charge conversion efficiency with low compression modulus (stiffness) effectively enhance d33. The SR structure exhibited optimal polarization charge conversion, the Fks-Shellular (FksS) structure within TPMS showed low stiffness, and the Octa&SR structure combined both properties. Notably, all three structures displayed exceptional piezoelectric performance. Specifically, the FksS structure achieved a substantial d33 of 194 pC/N, a 24% enhancement over conventional solid BaTiO3, while maintaining isotropic and stress-insensitive properties. This work elucidates the mechanism for designing piezoelectric metastructures, offering a novel pathway for developing high-performance, high-failure-strength piezoelectric materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3547-7
Inorganic perovskite solar cells (IPSCs) have attracted significant attention due to their excellent light and thermal stability and potential in tandem applications. However, their efficiency and stability are often limited by residual lattice stress and defects at interfaces and within the bulk, causing severe nonradiative recombination. Here, we introduce a zero-dimensional supramolecular complex, (ETP)2SbCl5, as a dual-interface and bulk modifier to regulate CsPbI3 film growth. The modifier exhibits spatial segregation: ETP+ cations anchor at the buried interface, passivating defects on TiO2 and perovskite surfaces; Sb3+ and Cl− ions diffuse into the bulk during annealing, relieving residual stress; and Cl− accumulates on the top surface, passivating cation defects. Consequently, the modified CsPbI3 solar cell achieves a power conversion efficiency (PCE) of 21.71% and an open-circuit voltage (VOC) of 1.27 V, retaining 97.4% of initial efficiency after 500 h of maximum power point (MPP) tracking. This work demonstrates a synergistic strategy to simultaneously address interfacial and bulk defects, advancing high-performance and stable inorganic photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3676-3
Perovskite solar cells (PerSCs) have achieved remarkable efficiencies, yet their performance is limited by defect states and non-radiative recombination. Here, pyromellitic diimide (PD) is introduced as an additive to passivate bulk defects in perovskite films. PD forms hydrogen bonds with formamidinium (FA+) ions and coordinates with Pb2+ ions, effectively suppressing non-radiative recombination and reducing energy loss. The PD-treated perovskite films exhibit enhanced crystallinity and uniformity. Consequently, 1.55 eV PerSCs achieve a high open-circuit voltage (VOC) of 1.193 V and a power conversion efficiency (PCE) of 25.79%. Moreover, unencapsulated PD-treated devices retain 96% of their initial efficiency after 2000 h under nitrogen atmosphere, whereas control devices retain only 74%. Under ISOS-D-2I accelerated aging (65±5°C in N2), PD-treated devices show less than 5% PCE attenuation after 288 h, compared to ~30% for controls. This work provides a viable strategy for defect passivation in perovskite solar cells, enhancing both efficiency and stability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3721-y
Anisotropic hydrogels have attracted significant attention for applications in actuators, soft robotics, and artificial muscles due to their ability to undergo shape morphing and generate anisotropic responses under external stimuli. Here, we report a novel strategy for fabricating anisotropic hydrogels using liquid crystal polymers (LCPs). A series of liquid crystal polyester-polyethylene glycol (LCP-PEG) multiblock copolymers with varying PEG block molecular weights were synthesized via one-pot melt-polycondensation. Upon stretching, LCP-PEG forms a stable, oriented microphase-separated lamellar structure, which enables reversible shape changes driven by melting-induced contraction and crystallization-induced expansion of the oriented PEG crystals. This unique structure imparts anisotropic swelling behavior to the films when exposed to water or humidity. The oriented microphase-separated lamellar structure confers high fracture strength (11.2–14.7 MPa), fracture strain (1600%–2100%), fracture energy (1.7–2.8 MJ m−2), and Young’s modulus (51.2–139.9 MPa). Furthermore, the anisotropic LCP-PEG hydrogel actuators exhibit versatile locomotion modes, including object grabbing and transfer between water and air, object gripping in rainy conditions, walking and somersaulting on ratchet-patterned bases under humidity stimuli, and slope climbing through somersault locomotion under salty water stimuli. These results demonstrate the potential of LCP-based anisotropic hydrogels for advanced soft robotic applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3615-1
Stretchable electronics are pivotal for bio-integrated devices, soft robotics, and wearables, yet their development is constrained by single-layer architectures that limit integration density and by mechanical mismatch between rigid components and soft substrates, which curtails service life. Here, we introduce a LEGO-like modular assembly strategy to construct multilayer three-dimensional (3D) stretchable electronics. Electronic components (ECs) and self-healing polyurethane (SPU) substrates patterned with liquid metal (LM) circuits serve as the modular blocks. This design simplifies fabrication and markedly enhances 3D integration density. The combination of LM circuits and self-healing elastic substrates enables devices to withstand diverse deformations and to autonomously heal after mechanical damage. Notably, the devices can undergo multiple recycling and reuse cycles without significant performance loss. This methodology offers a new paradigm for advanced flexible electronics, addressing critical bottlenecks in integration density, mechanical robustness, and sustainability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3538-6
The understanding of anion transporting behaviors under sub-nanoconfined regimes can guide the design of high-performance anion selective membranes (ASMs), yet it is little known. Here, we build membrane channels that combine physical rigidity with chemical affinity to anions simply through bridging graphene oxide nanosheets with charged linkers. We observe that the rigidly confined interaction imposed by channels to anions can reconfigure hydration shells in varying degrees for different anions via compensating for hydration-induced energy barriers and differentiating their rearrangement behaviors. During the configuration evolution, water molecules within hydration shells would rotate and simultaneously change their distance from the ion center. Based on the big discrepancy in configuration evolution, these membranes can realize ultrahigh selectivity of, for example, 125 for Cl−/SO4^2− and surpass the performance upper bound concerning Cl−/SO4^2− separation by other membranes. The knowledge of the configuration change of hydration shells during the dehydration process will be key to designing next-generation ASMs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3520-1
Solution-processed metal halide perovskite light-emitting diodes (PeLEDs) have advanced rapidly due to high color purity, tunable emission, and low cost, with external quantum efficiencies (EQEs) surpassing 30%. However, high EQEs are typically achieved at low brightness, suffering severe efficiency roll-off at high current densities due to Auger recombination and Joule heating. Three-dimensional (3D) perovskites offer superior charge transport but suffer from low photoluminescent quantum yield (PLQY) and efficiency roll-off. The fundamental roll-off mechanism remains poorly understood. Recently, Yao and co-workers developed a molecule-in-lattice-enabled intragrain heterostructure in 3D perovskite to promote carrier confinement. Using device-level ultrafast spectroscopy, they identified hole leakage as the origin of efficiency roll-off in pure-red CsPbI3−xBrx PeLEDs. A strong bonding small molecule with multiple anchor groups was introduced to penetrate the lead halide octahedron framework, constructing wide bandgap barriers inside perovskite grains, reducing hole leakage without compromising carrier transport. This approach enabled ultrabright, highly efficient, and stable pure-red PeLEDs with extremely low efficiency roll-off. The work provides a new strategy for achieving high brightness and efficiency simultaneously, advancing PeLED technology toward practical applications in displays and lighting.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3694-3
Lithium metal anodes (LMAs) are among the most promising candidates for next-generation batteries with high energy density. However, their practical application is hindered by persistent challenges such as dendritic lithium growth, unstable solid electrolyte interphases (SEI), and poor Coulombic efficiency. Surface coating has emerged as a viable solution to address these limitations. In particular, atomic and molecular layer deposition (ALD/MLD) techniques offer unparalleled control over the fabrication of ultrathin, conformal coatings, making them especially suitable for stabilizing LMA interfaces. This review comprehensively summarizes recent progress in applying ALD and MLD methodologies to construct durable artificial interphases on LMAs. We discuss the underlying mechanisms through which these coatings inhibit dendrite formation, improve interfacial integrity, and facilitate uniform lithium-ion transport. The roles of inorganic ALD coatings, organic MLD coatings, and their organic–inorganic hybrids are systematically examined, with a focus on their chemical composition, deposition behavior, and electrochemical characteristics. Moreover, we highlight the enhanced performance achieved through the integration of ALD/MLD-engineered interfaces in full-cell systems. The review concludes with a discussion of current challenges and potential research avenues aimed at advancing the rational development of effective LMA protection strategies. Overall, this work offers valuable insights into the role of interfacial engineering via ALD and MLD in enabling the practical deployment of lithium metal batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3648-2
Transient energy storage devices represent an emerging class of biodegradable power systems that provide temporary energy for implantable medical electronics before safely degrading in vivo. From early transient primary batteries to contemporary rechargeable batteries integrated with wireless charging systems, these devices have evolved to enable stable prolonged power supply. Through rational transient design and structural engineering, they achieve desirable electrochemical performance, tunable degradation rates, and mechanical compatibility with soft, irregular, and dynamic biological tissues. This work provides a critical review of state-of-the-art transient energy storage devices, including transient primary batteries, transient secondary batteries, and transient supercapacitors, with emphasis on their electrodes, electrolytes, encapsulation materials, fabrication processes, and applications. We critically analyze material selection strategies, transient design principles, and architecture design for various transient batteries and capacitors. Finally, we discuss existing challenges and outline future directions to guide the clinical translation of biodegradable power solutions for biomedical implants.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3575-4
Halide perovskite memristors, known for their ion mobility, have emerged as strong candidates for computational units in next-generation memory and neuromorphic computing systems. Nevertheless, most memristors are limited to operating in a single mode, either resistive switching or threshold switching. In this work, we overcome this limitation by developing dual-mode α-formamidinium lead triiodide (α-FAPbI3) perovskite memristors with switchable volatile/nonvolatile states, enabled by engineered SnO2 electron transport layers (ETLs). Through molecular interface optimization using 3-(N,N′-dimethylmyristylammonio) propanesulfonate (Z14) and 4,4′-(1,10-phenanthroline-3,8-diyl)bis(N,N′-bis(4-methoxyphen-yl)aniline) (PNL), we achieved exceptional device stability. Volatile devices exhibited >500 switching cycles, while nonvolatile devices surpassed 1000 cycles, both maintaining a high on/off ratio (~10^3). Beyond memory applications, these devices successfully emulated biological functionalities. The volatile mode replicated four key nociceptor characteristics (threshold, relaxation, sensitization, and no adaptation), while the nonvolatile mode demonstrated advanced synaptic plasticity, including paired-pulse facilitation (PPF) and spike-timing-dependent plasticity (STDP). Capitalizing on this dual-mode synergy, we constructed a spiking neural network (SNN) for handwritten digit recognition, achieving a 93% accuracy rate—a significant milestone for perovskite-based neuromorphic systems. This study not only provides a material-level strategy for multifunctional memristor design but also bridges the gap between biological sensing and artificial intelligence, paving the way for adaptive neuromorphic hardware.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3623-y
Organic light-emitting diodes (OLEDs) are an advanced technology for full-color displays, yet the low efficiency of blue OLEDs remains a critical bottleneck. Here, we report a new strategy to design robust Pt(II) emitters with enhanced molecular rigidity and increased locally excited character. The resulting Pt(II) emitter exhibits an extremely narrow emission spectrum peaking at 458.6 nm with a full-width at half-maximum (FWHM) of 16.0 nm and a small Huang-Rhys factor of 0.278, together with a high photoluminescence quantum efficiency of 95%. When doped into an OLED, the device emits at 464 nm with high color purity (FWHM = 19 nm) and achieves high external quantum efficiencies (EQEs) of 32.6%, 29.4%, and 26.9% at luminances of 123, 1000, and 5000 cd/m2, respectively. Notably, the device attains a record-high maximum brightness of 84,895 cd/m2 among reported deep-blue OLEDs with Commission Internationale de l'Éclairage (CIE) y-coordinate < 0.15. This work demonstrates one of the highest-performing deep-blue OLEDs reported to date, addressing the dual challenges of efficiency and brightness in this spectral region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3610-7
Electrochemical CO2 reduction reaction (CO2RR) offers an attractive route to produce value-added multicarbon (C2+) products, yet suffers from competing hydrogen evolution and monocarbon production. Here, we propose a dual-confinement effect on CO2 reactant and *CO intermediate, induced by tuning the pore configuration of reconstructed covalent organic frameworks (RC-COFs). The highly crystalline microporous RC-COF-1, when coated on a Cu electrode, enhances local CO2 concentration and restricts CO diffusion, thereby promoting C-C coupling. In acidic electrolyte, the RC-COF-1@Cu electrode achieves a maximum C2+ Faradaic efficiency (FE) of 67.0% at 500 mA cm−2, while maintaining a total carbon product FE above 90% across a broad current density range (100–500 mA cm−2). Experimental and theoretical analyses confirm that the ordered micropores of RC-COF-1 modulate reactant adsorption and intermediate diffusion, leading to improved C2+ selectivity. This work underscores the critical role of COF pore architecture in microenvironment engineering for heterogeneous catalysis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3637-6
Traditional optical fiber communication encryption methods lack sufficient dynamic adaptability and hardware flexibility, while reconfigurable logic gates can overcome this limitation, thereby significantly improving the flexibility of encryption systems. This study reports a reconfigurable optoelectronic logic gate (OELG) system based on hafnium-zirconium oxide (HZO) ferroelectric thin films. Through ultra-low temperature atomic layer deposition technique, the fabricated HZO thin films demonstrate an exceptional pyroelectric coefficient of 1835.91 μC m−2 K−1 and robust multi-level polarization stability, enabling efficient broadband photon-to-current conversion. By leveraging the pyroelectric effect and tunable polarization states, the OELG device achieves dynamic optical signal modulation and logic processing. The OELG device supports five fundamental logic operations (AND, OR, NAND, NOR, NOT) via electrical bias and polarization control, without requiring hardware modifications. The OELG device demonstrates stable performance over 10^9 cycles with no degradation, meeting practical application requirements. Furthermore, a convolutional neural network (CNN)-integrated image encryption-decryption framework was validated, achieving 95.01% recognition accuracy on decrypted data, while unauthorized decryption attempts resulted in significant feature loss. This study addresses security challenges in optical communication networks by proposing an innovative solution that integrates pyroelectric materials with reconfigurable logic gate technology, offering a new pathway to enhance physical-layer security.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3647-4
Chromium oxides (CrOx) and fluorinated graphite (CFx) are two typical cathode materials for lithium primary batteries. The former possesses the highest theoretical energy density but suffers from low practical capacity and inferior rate capability; the latter has the highest theoretical discharge capacity but fails to support fast discharge. Combining the merits of both cathodes via a composite design is desirable, yet the electrochemical performance of such composites remains unsatisfactory. In this work, we identified that by regulating the overlapped discharge potential of these two cathodes, fluorine atoms migrate from CFx to CrOx, leading to a homogeneous distribution of LiF and improved ionic and electronic conductivity, ultimately enhancing high-rate discharge performance. Benefiting from this synergetic effect, the CrOx/10%eCFx composite exhibits a considerably high energy density of 496.59 Wh kg−1 at a power density of 49.7 kW kg−1 (50 C), far superior to pure CrOx and CFx electrodes. We believe that the high-performance CrOx/eCFx composite cathode will justify its practical application in revitalizing advanced lithium primary batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3666-2
Light-emitting electrochemical cells (LECs) are promising for low-cost, solution-processed display and lighting applications, yet achieving high efficiency and color purity remains challenging. Here, we report two ionic multi-resonance (MR) emitters with narrowband blue emission for high-color-purity LECs. By covalently bonding an imidazolium functional group into a boron/nitrogen-doped polycyclic skeleton, the emitters retain the narrowband emission and high photoluminescence quantum yield (PLQY) of the MR core while gaining ionic character. The design exploits two types of nitrogen atoms in the imidazolium unit: the pyrrolic N at the 1-position forms a para-B-π-N linkage, elevating excited-state energy levels and blue-shifting emission; the pyridinic N at the 3-position provides a quaternization site, yielding intrinsically ionic emitters compatible with ionic hosts. The emitters exhibit blue emission with narrow full-width at half-maximum of 26–27 nm and high PLQYs of 95%–97% in solid-state films. LECs based on these emitters achieve narrowband blue electroluminescence with CIE coordinates of (0.12, 0.26) and a maximum external quantum efficiency (EQE) of 4.6%, representing the first narrowband blue LECs based on intrinsically ionic MR emitters. This work demonstrates a viable molecular design strategy for high-color-purity LECs, addressing the long-standing trade-off between efficiency and color purity in this technology.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3706-3
Aprotic lithium-oxygen (Li-O2) batteries are severely limited by slow cathode reaction kinetics and large polarization. Herein, we design and prepare a Mott-Schottky catalyst by uniformly embedding ultrafine Ru nanoparticles on nitrogen-doped carbon (Ru@NC) nanoflakes to accelerate oxygen redox kinetics of Li-O2 batteries. The Mott-Schottky effect of Ru@NC drives spontaneous electron rearrangement in the NC matrix and induces a strong built-in electric field at heterointerfaces, which accelerates the activation and conversion of oxygen intermediates. The obtained Ru@NC possesses rich Mott-Schottky heterointerfaces and defective carbon structures, which provide extensive adsorption and nucleation sites. More importantly, Ru@NC manifests moderate affinity for the intermediate LiO2, inducing formation of unique nanosheet-like Li2O2 with low Li2O2/cathode interfacial impedance, which further enhances oxidation kinetics. These enable the Li-O2 battery with Ru@NC to deliver a remarkably reduced polarization of 0.89 V, superior rate performance, and prolonged lifespan of over 200 cycles. This work will provide valuable guidelines for engineering advanced electrocatalysts for high-performance Li-O2 batteries and beyond.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3658-1
Organic-inorganic hybrid copper(I) halide semiconductors have attracted extensive attention for applications in phosphor-converted white light-emitting diodes (pc-WLEDs), X-ray imaging, and photodetectors because of their superior photo/radioluminescence, structural diversity, and eco-friendliness. In previous work, a strategy combining coordinated anionic inorganic modules with cationic derivatives yielded highly efficient blue-emitting hybrids, but synthesis complexity limited practical use. Here, we report a facile, efficient, and rapid solution-based ultrasonic treatment method for synthesizing high-performance blue-emitting phosphors using inexpensive, commercially available tetraethylammonium halides (TEAX, X = Cl, Br, I). The synergistic interplay of ionic and covalent bonds in these compounds endows them with a high photoluminescence quantum yield (PLQY) of 70% and excellent stability. These materials exhibit thermally activated delayed fluorescence (TADF), delivering outstanding performance in pc-WLEDs and X-ray imaging. Their exceptional properties highlight significant potential for use in optoelectronic devices and X-ray scintillators. This work provides an important reference for rapid synthesis of high-performance copper(I) halide hybrid phosphors and paves the way for commercial application.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3712-2
Electrochemical potential and ion diffusion of electrode materials restrain the energy and power densities of lithium-ion batteries, and these challenges also remain in the intercalation-type Li3VO4 (LVO). In this work, the local [VO4] coordination symmetry in LVO is broken by a higher concentration of oxygen vacancies (Vö), resulting in an increased average V–O bond length and a larger ligand field splitting. These alterations reduce the energy level of the lowest unoccupied orbitals (e*) and lift the electrochemical potential, resulting in a higher voltage output. Additionally, the broken local symmetry in Vö-LVO is found to reduce the band gap and expand the ion transport channels, which favors enhancing electronic conductivity and facilitates ion diffusion, thereby improving the electrochemical kinetics in the energy storage process. The local symmetry broken sample (Vö-LVO) achieves a significantly improved capacity of 532 mAh/g at 0.1 A/g in comparison with 394 mAh/g of pristine LVO, and long cycling stability with retained capacity of 398 mAh/g at 1 A/g over 500 cycles compared with 236 mAh/g of the pristine LVO. The fundamental understanding paves the way to exploit high-performance electrodes via ligand field engineering for next-generation rechargeable batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3746-x
The polyanionic compound Na3V2(PO4)2O2F (NVPOF) possesses a stable three-dimensional framework, high theoretical specific capacity, and favorable operating voltage, yet its sluggish Na+ diffusion kinetics and low electronic conductivity impede industrial application. This study proposes a dual regulation strategy combining carbon coating and heat treatment temperature to synergistically enhance crystallinity and electrochemical performance. NVPOF@C-400 and NVPOF@C-600 were synthesized via in-situ dopamine hydrochloride coating followed by heat treatment at 400 °C and 600 °C, respectively. Carbon coating at 600 °C significantly improved crystallinity and increased electronic conductivity by three orders of magnitude through the carbon layer's conductive network. The ~4.5 nm carbon layer effectively suppressed abnormal grain growth and secondary crystallization aggregation at high temperatures, maintaining uniform particle size of approximately 0.36 μm, which shortens Na+ diffusion pathways and prevents ion transport obstruction. Consequently, NVPOF@C-600 delivered a high discharge capacity of 102.5 mAh g−1 at 20 C and retained 96.5% capacity after 10,000 cycles. In a full-cell configuration with hard carbon (HC), NVPOF@C-600//HC achieved an impressive 89.3% capacity retention after 9,000 cycles. This work provides critical insights for practical implementation of high-performance NVPOF cathodes in sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3682-6
Metal single-atoms with optimized coordination structure on highly accessible substrate can maximize the metal utilization efficiency along with enhancing catalytic activities. Herein, axial nitrogen-coordinated Fe-N5 sites on N-doped carbon (denoted as FeN5@N-C) hollow microplates are fabricated via a unique Fe3+-chelated polydopamine assisted hollowing strategy using ZIF-L microplates as multifunctional templates. Due to the powerful chelating and adhesive ability of polydopamine, this hollow-carbon strategy can be extended to fabricate single-atom Fe-N-C hollow structures with different shapes and encapsulate other transition-metal single atoms (Ni, Co, Mn, and Cu) into the N-doped carbon hollow microplates. The FeN5@N-C hollow microplates exhibit outstanding oxygen reduction reaction (ORR) capability with an impressive half-wave potential of 0.93 V vs. reversible hydrogen electrode and high stability, which can serve as air-cathode catalysts for high-performance Zn-air batteries with high peak power density of 225.3 mW cm−2 and stable cyclability of up to 400 h. Comprehensive analysis and theoretical calculations elucidate that axial nitrogen coordination in Fe-N5 catalytic sites, unlike the planar Fe-N4 configuration, can compete well with the bonding of OH* through additional 3d-2p orbital hybridization, thereby giving moderate bonding strength to enhance the ORR activity.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3672-8
Pore-tuning engineering is an effective strategy for designing catalysts for energy storage and conversion. Here, we report a rhombic dodecahedral iron and nitrogen co-doped carbon (Fe-N-C) material with hierarchical micro-mesoporous structures, synthesized using mesoporous silica as both pore template and iron source. The resulting catalyst (m-Fe/NC) exhibits significantly enhanced oxygen reduction reaction (ORR) activity, with half-wave potentials of 0.81 V and 0.88 V in acidic and alkaline media, respectively. When employed as a cathode in zinc-air batteries, m-Fe/NC delivers a superior specific capacity of 815 mAh g_Zn^-1 and a stable cell voltage of 1.31 V at a current density of 10 mA cm^-2. Advanced characterization and theoretical calculations reveal that the mesoporous structure not only increases active site exposure but also induces a curvature-induced strain effect on concave surfaces, which enhances intrinsic activity. This work provides insights for developing innovative nanoporous electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3684-4
The efficient conversion of dinitrogen (N2) to ammonia (NH3) under mild conditions remains a critical challenge for sustainable nitrogen fixation. This study reports a rationally designed ternary heterojunction, GO/MXene/UiO-66 (GM/UiO-66), which achieves directed charge transfer for enhanced photocatalytic nitrogen fixation. The internal electric field at the heterointerface drives anisotropic migration of photogenerated charges, leading to rapid separation of electron–hole pairs and suppression of interfacial recombination. The intrinsic defect structure of graphene oxide (GO) provides active sites for N2 adsorption and activation, while π–π interactions between GO and UiO-66 accelerate electron transfer. Additionally, the Schottky junction between UiO-66 and MXene facilitates hole (h+) transfer. The incorporation of GO and MXene extends visible-light absorption of UiO-66. Under simulated solar illumination, GM/UiO-66 exhibits an NH3 generation rate of 25.1 μmol g−1 h−1, which is 1.9 times higher than that of pristine UiO-66 (13.5 μmol g−1 h−1). This work presents a novel strategy for designing ternary heterojunction composites that optimize charge transfer and significantly improve photocatalytic performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3625-3
Zirconia (ZrO2)-based fluorite ferroelectric materials are promising for nonvolatile memory and logic devices due to their CMOS compatibility and cost advantages over hafnium oxide (HfO2). However, the metastable nature of the ferroelectric orthorhombic phase (o-phase) hinders practical application. Here, we report the strain-mediated stabilization of the ferroelectric o-phase in ZrO2 thin films grown on niobium-doped strontium titanate (NSTO) substrates with different crystallographic orientations via chemical solution deposition. Systematic structural and ferroelectric characterization, combined with simulation, reveals that substrate orientation controls in-plane tensile strain, selectively promoting epitaxial growth of the o-phase. The ZrO2 film on NSTO(110) exhibits the highest o-phase content, achieving a remanent polarization (2Pr) of 92.64 μC/cm², which remains as high as 88.54 μC/cm² after resistive-capacitive (RC) delay calibration. The device shows endurance of approximately 10^7 cycles with favorable fatigue characteristics. X-ray absorption spectroscopy (XAS) further indicates distortion of Zr-O tetrahedra, providing microscopic insight into the ferroelectricity. This work presents a novel strategy for property tuning of ZrO2 films and supports their application in storage and logic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3719-8
The proliferation of 5G communications and smart electronic devices has intensified electromagnetic wave (EMW) pollution, necessitating microwave absorption materials (MAMs) with high efficiency, lightweight, and flexibility. Traditional MAMs suffer from high density and narrow effective absorption bandwidth (EAB). This work presents a lightweight, flexible microwave-absorbing composite fabricated by in-situ polymerization foaming of polyurethane (PU) with multi-walled carbon nanotubes (MWCNTs) and flaky carbonyl iron (FCI). The hierarchical PU composite foam, designated 3*PFC 0.5-1.0-1.5, achieves an EAB of 15.7 GHz, covering 98.1% of the tested 2–18 GHz range, including S, C, X, and Ku bands. This performance stems from synergistic conductive and magnetic losses, along with impedance matching facilitated by the hierarchical porous structure. The composite maintains low density and high compressibility, offering a promising solution for EMW absorption in 5G, military stealth, and smart devices. The in-situ method ensures strong interfacial adhesion between fillers and matrix, enhancing durability compared to impregnation methods. This study demonstrates a scalable approach to fabricate high-performance MAMs with broad bandwidth and mechanical robustness.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3663-6
Escalating global climate change has precipitated a dramatic surge in building cooling/heating energy demands, critically undermining urban sustainability. Although dynamic thermal management technologies show potential for reducing architectural carbon footprints, prevailing active regulation systems remain constrained by energy-intensive mode-switching mechanisms and unsustainable operational costs. Here, we develop a zebra-inspired radiative modulator (ZIRM) that achieves climate-customized building thermal management through spatially partitioned integration of radiative cooling (RC) and heating (RH) functional units. The material breakthrough resides in a hybrid thin-film architecture combining a cellulose acetate/Zeolitic imidazolate framework-L (ZIF-L) porous membrane (solar reflectance ~95%, thermal emissivity ~0.88) with an MXene/ZIF-67 derived carbon-based absorption layer (solar absorption ~93%, thermal emissivity ~0.37), resolving the opto-thermal coupling limitations inherent to conventional materials. Experimental verification demonstrates that programmable regulation of the RC/RH area ratio enables broad-range temperature differential control from −4.3 to 12.1 °C during daytime operation. Building energy simulations reveal ZIRM’s annual energy consumption of 1.45×10^10 GJ, corresponding to 9.9% and 2.7% reductions compared to pure RC and RH systems, respectively. The established “configuration-environment-performance” predictive model pioneers a paradigm-shifting solution for carbon-neutral architecture, synergizing material innovation with climate-customized engineering strategies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3686-6
Fused silica (SiO2) exhibits exceptional thermal stability and dielectric properties, making it an attractive material for aerospace and military applications. However, its relatively poor mechanical performance has limited its widespread practical utilization. This study proposed an innovative approach to fabricate SiO2-hexagonal boron nitride (hBN) composite ceramics via spark plasma sintering (SPS), leveraging the high-temperature phase transformation of cubic boron nitride (cBN) to introduce randomly oriented hBN as a reinforcing phase within the SiO2 matrix. The randomly oriented hBN nanoplates allow cracks to propagate along stronger grain boundaries, rather than along weaker interlayers of hBN, significantly improving the overall strength and fracture toughness of the composite. The maximum flexural strength and fracture toughness achieved are 183.4 MPa and 2.06 MPa m1/2 respectively, which are 3.6 times and 4 times that of fused SiO2. Concurrently, the composites exhibit low dielectric constants (ε = 3.58–3.69) and dielectric losses (tan δ < 0.0087) at 1 MHz. This work successfully enhanced the mechanical performance of fused SiO2 while preserving its excellent dielectric characteristics, opening new possibilities for its potential applications in advanced structural and functional fields.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3652-2
Existing robotic end-effector gripping technologies often encounter challenges such as poor adaptability to environmental changes, incomplete deformation sensing, and insufficient adhesion stability, which can compromise operational safety and reliability. Here, we present the bio-inspired self-sensing suction cup, in which the core self-sensing capability is achieved by combining high-performance, laser-induced graphene/Ag NWs flexible sensors with a Wheatstone bridge design. The flexible sensors provide high sensitivity, while the Wheatstone bridge circuit enables accurate and stable detection of deformation during the gripping process. Integrated into the octopus-inspired suction cup, this system allows for real-time monitoring of deformation and adsorption stability. The self-sensing suction cup demonstrates good performance across a 0–25 kPa negative pressure range, with outstanding linearity (R2 = 0.993) and high sensitivity (GF = 10.436 kPa−1). Experimental results confirm that the suction cup can achieve stable adsorption under varying loads and enable real-time monitoring of the suction cup status during the gripping process. This design provides a promising solution for intelligent gripping systems, logistics, and object recognition in challenging environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3860-0
Drug detection is critical for public health and security, yet reversible and highly sensitive sensing materials remain scarce. This study presents a novel ionogel sensor material, poly(ethylene glycol) diacrylate (PEGDA)/1-butyl-3-methylimidazole tetrafluoroborate, for reproducible detection of N-methylphenylethylamine (MPEA), a structural analogue of methamphetamine. The ionogel is fabricated by immobilizing a flowable ionic liquid within a PEGDA network via UV curing, preserving ionic mobility for efficient conduction. Integrated on a flexible poly(ethylene naphthalate) substrate, the sensor exhibits over 72.6% transmittance in the visible spectrum, enabling concealed attachment. Utilizing non-covalent interactions, the sensor achieves reproducible MPEA detection at sub-ppb levels at room temperature, with a theoretical detection limit of 317 ppt. It demonstrates high selectivity and consistency. Ionic conductivity was confirmed via current-voltage tests and impedance spectroscopy, and the sensing mechanism was clarified. The device maintains reliable performance under bending, indicating suitability for dynamic environments. With Bluetooth integration for wireless data transmission, the sensor shows strong potential for practical, discreet drug monitoring in real-world applications.