SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4472-0
Dynamic electrocardiography (ECG) monitoring during physical activity remains compromised by motion artifacts that corrupt signal fidelity, particularly with conventional gel electrodes whose impedance rises sharply under deformation. This work presents a thumb-sized liquid metal system integrating gallium-based epidermal electrodes with a self-adhesive elastomeric matrix to sustain robust ECG acquisition against motion. The electrodes exploit the fluidic compliance of eutectic gallium–indium to maintain continuous skin contact, while the adhesive formulation ensures stable interfacial coupling without additional fixation. The system achieves low motion artifact levels, preserving waveform morphology and R-peak detectability during ambulation. The compact form factor enables unobtrusive wearability, and the materials architecture addresses the trade-off between adhesion and conformability that limits existing dry electrodes. The study establishes a materials and device pathway for clinical-grade dynamic ECG in ambulatory and point-of-care settings, with implications for continuous cardiac monitoring where patient movement is unavoidable.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4433-5
Negative thermal expansion (NTE) and zero thermal expansion (ZTE) materials are technologically relevant for precision engineering, yet their practical deployment is constrained by narrow operating temperature windows. This study introduces an entropy-designing strategy to regulate the thermal expansion behavior in the AⅠBⅡCⅢMo3O12 system, specifically K0.4(Mg0.25Mn0.25Co0.25Ni0.25)0.4Sc1.6Mo3O12 (CE0.4MO) and related CExMO compositions (x = 0.4, 0.6, 0.8, 1.0). By tuning configurational entropy, the operating temperature windows for both NTE and ZTE are significantly broadened, with the ZTE region shifting to higher temperatures. Among single-phase compositions, CE0.4MO exhibits the lowest configurational entropy and demonstrates NTE from 100 to 830 K and ZTE up to 1100 K, surpassing most reported ZTE materials. Systematic analyses of structural evolution, lattice dynamics, and electronic structure reveal that reduced configurational entropy suppresses structural evolution, directly correlating with decreased structural flexibility. Higher atomic displacement parameters (ADPs) of oxygen in CE1.0MO provide experimental evidence for enhanced flexibility. Raman spectroscopy shows that the full width at half maximum (FWHM) of peaks in the 750–900 cm-1 range positively correlates with configurational entropy, indicating reduced lattice disorder, while modes within 750–1050 cm-1 blue-shift as entropy decreases, confirming lattice stiffening. Electron localization function (ELF) and charge density analyses indicate that Mg/Mn/Co/Ni/Sc–O bonds are ionic, with ionicity weakening as configurational entropy decreases, thereby enhancing constraints on atomic vibrations and reducing structural flexibility. This work establishes a theoretical foundation for designing thermal expansion materials with wide operating temperature ranges.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4371-6
The sluggish kinetics of the oxygen reduction reaction (ORR) necessitates platinum-based catalysts, but their high cost and scarcity drive the search for platinum-group metal-free (PGM-free) alternatives. Fe−N−C catalysts with atomically dispersed Fe−N4 sites are promising, yet their practical performance is limited by buried active sites and poor mass transport. Here, a crumpled, multi-scale porous Fe−N−C catalyst (Fe−N−PCG) is synthesized via spray pyrolysis coupled with high-temperature metal etching. The crumpled morphology, formed by capillary compression during rapid solvent evaporation, and in-plane mesopores from Fe nanoparticle etching, synergistically enhance site accessibility and mass transport. Fe−N−PCG achieves a site density (SD) of 2.74×10^19 sites g−1 and Fe utilization (UFe) of 51.7%. As a gas diffusion electrode, it delivers a mass transport overpotential (ηmt) of 67 mV at 800 mA cm−2. In zinc-air batteries, Fe−N−PCG exhibits a peak power density of 296.1 mW cm−2 at 500 mA cm−2, outperforming Pt/C (241 mW cm−2 at 438 mA cm−2). At 50 mA cm−2, it delivers a discharge voltage of 1.19 V and a specific capacity of 815 mAh g−1, surpassing Pt/C (1.13 V, 715 mAh g−1). These results demonstrate that morphology and porosity engineering can concurrently optimize intrinsic activity, site utilization, and mass transport, offering a rational design strategy for high-performance PGM-free catalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4248-2
Marine biofouling imposes substantial operational penalties on maritime assets, yet commercial silicone foul-release coatings rely on static, non-adaptive networks that cannot be reprocessed or repaired. This work introduces selenonium-salt-catalyzed dynamic siloxane exchange as a route to polydimethylsiloxane (PDMS) vitrimer coatings. The authors incorporate A16Se+ organoselenium catalysts into PDMS networks at loadings designated A16Se+xPDMS, enabling thermally activated siloxane bond exchange that confers vitrimeric stress relaxation, reprocessability, and high-temperature self-healing. Antibiofouling performance is benchmarked against pristine PDMS using colony morphology assays for Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa, SEM imaging of bacterial adhesion after 3 h, Chlorella fluorescence adhesion quantification, zeta potential measurements, and 3-month seawater immersion panels. Reviewer 1 questioned the direct relevance of recyclability and high-temperature self-healing to marine antifouling and requested that surface elastic modulus and Pseudomonas antibacterial data be elevated to the main text. In response, the authors relocated scratch and self-healing results from Figure 5 to Supporting Information Figures S12 and S13, condensed the main-text discussion, and integrated surface elastic modulus data into Figure 4G and Pseudomonas antibacterial results into Figure 6A. The revised manuscript positions dynamic exchange as supporting evidence of network dynamics rather than as a primary antifouling metric, while foregrounding modulus and antibacterial performance as the application-relevant properties.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4267-y
The synthesis of two-dimensional MBenes from MAB-phase ceramics is impeded by uncontrolled etching kinetics that compromise structural integrity and yield. This study introduces a vacuum molten salt strategy to regulate space-charge accumulation during the selective removal of Al from Mo2AlB2, producing honeycomb-like architectures. The vacuum environment suppresses oxidative side reactions and modulates ionic transport, enabling precise control over etching depth and morphology. The resulting Mo2AlB2 exhibits exceptional electromagnetic wave absorption, with a minimum reflection loss of -56.3 dB at 2.4 mm and an effective absorption bandwidth of 6.8 GHz. These metrics surpass conventional etching-derived MBenes by a factor of 2.5 in attenuation capacity. The space-charge-regulated mechanism is elucidated through in situ spectroscopic and computational analyses, revealing that vacancy-induced charge redistribution governs the etching front propagation. This work establishes a scalable route for high-purity MBenes with tailored porosity, addressing critical bottlenecks in energy absorption and catalytic applications. The vacuum molten salt approach eliminates the need for hazardous HF, offering a safer and more environmentally benign pathway for industrial translation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4362-y
The commercial viability of zinc-air batteries (ZABs) is constrained by the sluggish kinetics of the oxygen reduction reaction (ORR), which necessitates robust, cost-effective catalysts. While cobalt-based single-atom catalysts (Co SACs) exhibit superior selectivity and stability relative to Fe-N-C counterparts, their intrinsic ORR activity remains limited by scaling relations among intermediates. This study alleviates these constraints by precisely engineering the coordination symmetry of Co SACs. Through a mild annealing strategy, boron was incorporated into the first and second coordination shells of Co centers, creating an asymmetric Co-N3B-O local environment. The first-shell B/O coordination modulates the electronic structure of the Co center, while hydrogen bonding between *OOH and the coordinated O atom stabilizes the key intermediate, synergistically enhancing ORR activity. The optimized Co-BCN-950 catalyst delivers a peak power density of 216 mW cm-2 in ZABs, a 43% enhancement over commercial Pt/C (151 mW cm-2), alongside an open-circuit voltage of 1.43 V and a specific capacity of 790 mAh g-1. These findings establish a paradigm for tailoring the local coordination of SACs, enabling next-generation high-stability energy storage systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4383-8
Conventional cancer therapies remain constrained by undruggable oncogenic proteins and acquired resistance. Proteolysis targeting chimeras (PROTACs) have emerged as a transformative modality that harnesses the ubiquitin-proteasome system to selectively degrade target proteins, offering advantages over traditional small-molecule inhibitors. However, clinical translation of PROTACs is impeded by intrinsic physicochemical limitations: high molecular weight, poor bioavailability, and lack of tumor-specific delivery. Integrating PROTACs with nanotechnology has yielded advanced nano-PROTACs platforms. Nanocarriers enhance solubility and stability, optimize pharmacokinetics, and enable spatiotemporally controlled drug release through passive or active targeting. This review systematically summarizes recent advances in engineering multifunctional nano-PROTACs for cancer therapy, with particular emphasis on design strategies by which nanoengineering enhances PROTAC performance. We evaluate how these platforms improve anticancer efficacy and minimize systemic toxicity while exploring their therapeutic potential in monotherapy and synergistic treatment settings. Finally, we discuss current challenges and future perspectives, providing a theoretical and technical foundation for next-generation nano-PROTACs as a precise and potent strategy in precision oncology.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4412-y
GeTe-based thermoelectric materials are promising lead-free alternatives to PbTe, but their intrinsically high Ge vacancy concentration (~10^21 cm^-3) leads to excessive carrier density and degraded Seebeck coefficient. This study integrates resonant levels (RLs) via In doping and local van der Waals gaps via Sb/Bi alloying to decouple electron and phonon transport. The optimal composition Ge0.91Sb0.04Bi0.04In0.01Te exhibits a Seebeck coefficient of ~287.31 μV K^-1 at 323 K, more than double that of the In-free sample (~102.28 μV K^-1). The peak figure of merit zT reaches ~1.8 at 723 K, with an average zT of ~1.0 over 323–723 K. Vickers hardness is enhanced to ~224 HV, a ~93% improvement over pristine GeTe (~116 HV). X-ray diffraction reveals a structural evolution toward a pseudo-cubic phase with increasing In content, and the (202) peak shifts to lower angles, indicating lattice expansion. These results demonstrate that synergistic RLs and van der Waals gaps effectively optimize carrier concentration and suppress thermal conductivity, offering a viable route for high-performance, mechanically robust GeTe thermoelectrics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4405-9
Conventional metal-halide X-ray scintillators, including Bi4Ge3O12 (BGO), Cs(Na)I:Tl, and Lu1.8Y0.2SiO5:Ce (LYSO), suffer from hygroscopic decomposition, high-temperature fabrication, and mechanical rigidity, which restrict their deployment in harsh-environment radiography. This study reports a nontoxic zero-dimensional organic–inorganic hybrid copper(I) halide, Cu2I2(C26H36NP)2 (Compound G), synthesized via a room-temperature solution route. The bulky phosphine ligands confer exceptional superhydrophobicity, with the material retaining 91.95% of its initial luminescence after 30 days of water immersion. A flexible scintillator screen fabricated from styrene-ethylene-butene-styrene (SEBS) exhibits a light yield of ~32,500 photons MeV-1, a spatial resolution of 19.14 lp mm-1, and a detection limit of 0.8 μGyair s-1. The screen enables stable X-ray imaging under flexible, high-temperature, and underwater conditions, eliminating vignetting and distortion in nonplanar objects. These metrics demonstrate that the superhydrophobic copper(I) halide scintillator addresses the water-stability bottleneck of commercial scintillators while delivering competitive light output and resolution, offering a viable pathway for medical diagnosis, nondestructive inspection, security checking, and space exploration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4416-8
Copper(I)-based carbene-metal-amide (CMA) emitters offer an earth-abundant alternative to precious-metal phosphors for organic light-emitting diodes (OLEDs), yet efficient green emission remains scarce due to limited π-extension and unbalanced charge-transfer characteristics of N-heterocyclic carbene (NHC) ligands. This work introduces a pyrimidine-fused NHC ligand (CF3PMI) with balanced π-accepting ability, synthesized via a one-pot protocol in good yields. The resulting Cu(I)-CMA complex CF3PMI-BFCF3 exhibits green thermally activated delayed fluorescence (TADF) in doped thin films, with a photoluminescence quantum yield (PLQY) of 90% and a short emission lifetime of 1.16 μs. A vacuum-deposited OLED achieves green electroluminescence centered at 514 nm with an external quantum efficiency (EQE) of 22.7%. Furthermore, a hyperfluorescent OLED employing CF3PMI-BFCF3 as a sensitizer delivers an EQE of 21.8%, green emission at 537 nm, and a narrow full width at half maximum (FWHM) of 30 nm. These results establish a viable molecular design strategy for high-performance green-emitting Cu(I)-based TADF materials and provide a convenient synthetic route for Cu(I)-CMA emitters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4494-9
Superionic conductors exhibit high cation mobility arising from weak binding and continuous transport pathways, atomistically characterized by extensive structural disorder and partial occupancy akin to amorphization. This disorder, whether confined to a cation sublattice or extended to full amorphization, strongly impedes lattice thermal transport, rendering these materials intrinsically ideal thermal insulators. This work investigates Ag26I18W4O16, a superionic conductor tunable from fully amorphous to single-crystalline states, as a model system to probe the impact of disorder and amorphization on thermal transport. Extensive Ag+ disorder, in both crystalline and amorphous phases, reduces thermal conductivity to approximately the theoretical lower bound of 0.16 W/m-K with virtually no temperature dependence, while concurrently achieving the lowest mean sound velocity ever recorded for a dense solid. Pair distribution function (PDF) analysis of synchrotron X-ray total scattering data indicates that short-range disorder (< 5 Å), rather than long-range periodicity, governs thermal insulation performance in both phases. These findings suggest a design strategy reconciling structural stability with glass-like thermal insulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4313-7
Liquid-to-vapor mass transfer is central to energy and environmental processes. Conventional distillation relies on vapor-liquid equilibrium and device-level optimization, with materials playing passive structural roles. Non-boiling processes such as membrane distillation and interfacial solar evaporation localize phase change at confined interfaces, making mass transfer a materials-mediated transport phenomenon where interfacial structure and chemistry dictate evaporation kinetics, vapor escape, and solute rejection. Janus interface materials, featuring spatially separated hydrophilic and hydrophobic domains, introduce architectural asymmetry to regulate liquid-to-vapor mass transfer. This review summarizes recent advances, highlighting mechanisms including the cooperative pump-valve effect, nanoconfinement-enhanced transport, and mitigation of fouling and scaling. Representative applications in membrane distillation, solar-driven evaporation, and personal thermal-moisture management are systematically discussed. Key challenges and future opportunities are outlined, particularly in advancing fundamental understanding, scalable fabrication, and practical implementation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4468-6
The proliferation of multispectral detection platforms demands materials that simultaneously satisfy electromagnetic interference (EMI) shielding and infrared (IR) camouflage without compromising radio-frequency (RF) transmission. Conventional MXene films exhibit exceptional EMI shielding (>40 dB) but suffer from high IR emissivity and severe RF reflection, precluding integration with wave-transmitting arrays. This work introduces liquid metal (LM)-modified MXene composite films engineered via structural patterning to decouple optical, IR, and RF responses. The LM phase, dispersed within the MXene interlayer galleries, reduces free-electron density and tailors the dielectric loss, while a periodic array architecture creates impedance-matched windows for RF transmission. The resulting films achieve an EMI shielding effectiveness of 36 dB at 510 µm thickness, with a low IR emissivity of 0.36 and an RF transmittance exceeding 80% in the X-band. The patterning strategy suppresses surface current continuity, mitigating the trade-off between shielding and transmission. These metrics represent a 20% improvement in IR camouflage and a 15% enhancement in RF transparency relative to pristine MXene films. The composite films also demonstrate mechanical flexibility, retaining 95% of initial conductivity after 1,000 bending cycles. This work establishes a scalable route for multispectral-compatible materials critical for next-generation stealth and communication systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4238-2
Infrared nonlinear optical (IR NLO) materials are critical for laser frequency conversion, yet their performance is often constrained by a trade-off between second harmonic generation (SHG) efficiency and laser-induced damage threshold (LIDT). Here, we report a new ternary diamond-like compound, AlGaS3, which successfully balances these competing demands. AlGaS3 crystallizes in a noncentrosymmetric structure composed of wide HOMO-LUMO gap [AlS4] tetrahedra and NLO-active [GaS4] tetrahedra. The compound exhibits a wide experimental optical band gap of approximately 3.38 eV, which is significantly larger than that of the benchmark AgGaS2 (AGS, ~2.70 eV). This wide band gap contributes to a high laser-induced damage threshold (LIDT) of approximately 6.0 times that of AGS, as determined by powder-based measurements. Notably, AlGaS3 also demonstrates a phase-matching SHG response of approximately 0.5 times that of AGS at a fundamental wavelength of 2.09 μm, with particle size-dependent behavior confirming phase-matchability. The combination of wide band gap, high LIDT, and moderate SHG response positions AlGaS3 as a promising candidate for high-power IR NLO applications. This work provides a viable strategy for designing IR NLO materials with enhanced laser damage resistance by incorporating wide-gap tetrahedral units.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4138-5
Electrocoagulation (EC) has emerged as a promising electrochemical technology for wastewater treatment, offering distinct advantages over conventional chemical coagulation and membrane processes. This review systematically summarizes recent advancements in EC, focusing on the underlying mechanisms, key operating parameters, and diverse technical applications. The EC process involves three stages: electrolytic oxidation and in-situ coagulant formation, destabilization of contaminants, and floc formation. Unlike chemical coagulation, EC requires no external chemical additives, and process control is achieved by adjusting current density, voltage, or electrode materials, enabling adaptation to varying wastewater qualities. The review highlights the influence of dissolved organic matter (DOM) on EC efficiency, as clarified by Luo et al. (Water Research, 2025). Furthermore, it discusses reactor design innovations, including continuous-flow and cascade-type configurations, and the role of current waveforms in mitigating electrode passivation. The integration of EC with membrane bioreactors and forward osmosis is also examined, demonstrating enhanced treatment performance and fouling mitigation. Key challenges, such as energy consumption and electrode scaling, are addressed, along with future research directions. This comprehensive analysis provides a critical framework for optimizing EC systems and scaling them for industrial wastewater treatment, emphasizing the need for holistic reactor design and process integration to achieve sustainable water reuse.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4240-7
The electrocatalytic ammonia oxidation reaction (AOR) is pivotal for sustainable energy conversion and storage, enabling direct ammonia fuel cells (DAFCs), ammonia electrolysis, and solid oxide fuel cells. This review critically examines recent advances in AOR catalysis, emphasizing active-site regulation, interfacial engineering, and device-oriented catalyst development. For noble-metal catalysts, optimizing adsorption and dehydrogenation of NHx intermediates while mitigating poisoning is essential for sustained activity. Non-noble-metal systems, particularly Ni-based catalysts, require precise control of reconstructed working-state phases such as NiOOH-like species to balance activity and selectivity. Interfacial engineering, including heterointerfaces, defect structures, and doped coordination environments, strongly influences the competition between AOR and oxygen evolution reaction (OER), as well as product branching toward N2 or oxygenated nitrogen species. The review underscores that catalyst optimization now extends beyond bulk composition to the precise regulation of the interfacial reaction microenvironment. Furthermore, practical device operation is governed by membrane/electrolyte compatibility, mass transport, ammonia crossover, thermal management, and long-term durability. Bridging fundamental catalyst studies with deployable ammonia energy technologies requires coordinated optimization from active materials to electrode architectures and full-device systems. This review provides a comprehensive framework for designing next-generation AOR catalysts and accelerating their integration into industrial energy systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4269-4
Self-assembled molecular interlayers (SAMs) are promising hole-selective contacts for high-efficiency organic solar cells (OSCs) due to their well-defined energy alignment and minimal parasitic absorption. However, their intrinsically limited mechanical robustness often leads to structural degradation and performance loss under mechanical deformation, restricting their application in flexible devices. Here, we report a nanoparticle-reinforced self-assembled composite interface that simultaneously enhances mechanical reliability and optoelectronic performance. Uniformly dispersed SiO2 nanoparticles are introduced as high-modulus reinforcing building blocks without disturbing molecular self-assembly. In contrast to NiOx nanoparticles, which suffer from aggregation and parasitic absorption, SiO2 nanoparticles exhibit excellent dispersion and optical transparency, enabling formation of a structurally compatible hybrid interface. Mechanistic studies reveal that SiO2 nanoparticles redistribute interfacial stress and form dynamic hydrogen-bond networks with phosphonic acid groups of 2PACz, providing efficient energy dissipation during cyclic deformation. Meanwhile, modulation of interfacial polarity extends the crystallization time window of the active layer, resulting in enhanced molecular ordering and improved charge transport. As a result, devices based on the SiO2/2PACz composite interface achieve a power conversion efficiency of 20.14% for rigid devices and 19.30% for flexible devices, placing the flexible devices among the highest-performing flexible OSCs reported to date, while retaining over 90% of their initial efficiency after repeated bending cycles. This work establishes a general strategy for overcoming the trade-off between electronic selectivity and mechanical robustness in ultrathin self-assembled molecular interfaces, providing design insights for high-performance flexible organic optoelectronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4339-7
Neuromorphic computing demands energy-efficient synaptic devices that emulate biological plasticity. Optoelectronic memristors based on colloidal quantum dots (QDs) offer tunable bandgaps and solution processability, yet suffer from defect-mediated nonradiative recombination and instability. Here, we report ZnS-passivated CdZnSe core/shell QDs as the active layer in memristive devices, achieving enhanced synaptic emulation and information encryption. Time-resolved photoluminescence (TRPL) decay curves were fitted with a tri-exponential function, revealing that ZnS passivation suppresses defect-related trap states, prolonging the average carrier lifetime from 12.3 ns (CdZnSe) to 28.7 ns (CdZnSe/ZnS). The intensity proportion of the fast decay component (τ1 ≈ 1.2 ns) decreased from 45% to 18%, indicating reduced surface trapping. Devices incorporating CdZnSe/ZnS QDs exhibit stable bipolar resistive switching with an ON/OFF ratio exceeding 10^3, endurance of >10^3 cycles, and retention of >10^4 s. Under 365 nm UV illumination, the devices show light-tunable synaptic plasticity, including paired-pulse facilitation (PPF) with a facilitation index of 180% at a 50 ms interval, and transition from short-term to long-term memory. The memristors successfully emulate essential synaptic functions and are employed in a simple encryption scheme, demonstrating the potential of defect-passivated QDs for secure neuromorphic hardware.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4202-3
Carbon dots (CDs) with absorption in the second near-infrared window (NIR-II, 900-1700 nm) hold promise for tumor theranostics, yet existing synthesis methods often involve complex procedures, harsh conditions, or lack precise control. Here we report a 'self-photooxidation-restructuring' strategy that enables structural reorganization of the carbon core in CDs, achieving a significant redshift of absorption into the NIR-II region. Under ultraviolet (UV) light irradiation, the precursor (B-CDs, absorption in UV region) generates singlet oxygen, which self-oxidizes aldehyde groups and the carbon skeleton of B-CDs to stronger electron-withdrawing carboxyl groups and carbon radicals, respectively. These processes facilitate the formation of new C=C bonds between isolated aromatic domains, thereby transforming B-CDs into novel CDs (N-CDs) characterized by enhanced donor-acceptor interactions and a redshift in absorption toward the NIR-II window. Various experimental data, including high-resolution XPS, FTIR, NMR, EPR, have proved the proposed formation mechanism. The novel N-CDs afforded a high photothermal conversion efficiency of up to 71.33%, which enabled 1064 nm laser-activated photoacoustic imaging (PAI)-guided photothermal therapy (PTT) in tumors. This work opens a new avenue for the synthesis and modulation of CDs in the NIR-II region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4354-9
This review systematically examines the synthesis-structure-property relationships of hybrid graphene and carbon fiber reinforced composites, encompassing polymer, metal, and ceramic matrix systems. The hybridization of graphene with carbon fibers addresses the intrinsic limitations of conventional composites, such as weak interfacial bonding and insufficient multifunctionality. The review consolidates recent advances in fabrication strategies, including electrophoretic deposition, layer-by-layer assembly, and precursor impregnation, which enable controlled graphene distribution and orientation. Critical analyses of mechanical, tribological, electrochemical, and anti-ablation properties reveal that graphene addition significantly enhances interfacial shear strength, thermal stability, and electrical conductivity. For instance, in copper matrix composites, the incorporation of reduced graphene oxide with short carbon fibers improves tribological performance, reducing wear rates under specific load conditions. In ceramic matrix composites, graphene-modified C/C-SiC composites exhibit superior anti-ablation resistance, with mass loss rates reduced by up to 30% at elevated temperatures. Furthermore, graphene-coated carbon fiber electrodes demonstrate high specific capacitance and cycling stability in energy storage applications. The review also addresses challenges such as dispersion uniformity, scalability, and cost-effectiveness, proposing future directions for industrial adoption. By providing a comprehensive framework, this work guides the design of next-generation hybrid composites tailored for aerospace, automotive, and energy storage sectors.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4342-3
Electron acceptors containing single-bond-linked building blocks offer attractive advantages for organic solar cells owing to their synthetic simplicity and structural modularity. However, achieving backbone planarity without compromising electronic compatibility remains a persistent challenge. Conventional conformational locking strategies based on alkoxy substitution can effectively suppress torsional freedom but often elevate the highest occupied molecular orbital energy level, limiting compatibility with widely used donor polymers. Here, we report a partially fused electron acceptor design that achieves intrinsic backbone planarity through heterocycle selection rather than side-chain-assisted conformational locking. By incorporating a benzodifuran core and furan-thiophene linkages, the resulting acceptors exhibit a near-coplanar backbone geometry as revealed by density functional theory calculations, without the need for electronically perturbing alkoxy groups. Devices based on the optimized acceptor (BDF-1) deliver a binary power conversion efficiency of 12.2%, and further improvement to 19.5% is achieved in a ternary blend with PM6 and BTP-eC9. The enhanced performance is accompanied by favorable morphology, balanced charge transport, and suppressed recombination losses. This work provides molecular-level insight into partially fused acceptor design and demonstrates that heteroatom-guided conformational locking offers a viable strategy for expanding the design space of acceptors with single-bond-linked building blocks while maintaining compatibility with mainstream donor systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4381-5
Bismuth telluride (Bi2Te3)-based alloys remain the benchmark for low-temperature thermoelectric applications, yet their conversion efficiency is limited by the trade-off between electrical and thermal transport. This study introduces a pseudo grain boundary engineering strategy to simultaneously enhance the average figure of merit (ZT) in p-type (Bi,Sb)2Te3 (BST) materials. By incorporating Ag-based compounds, the carrier concentration is optimized via substitution of Ag+ ions, while the introduction of secondary phases at grain boundaries effectively suppresses lattice thermal conductivity. The approach yields a peak ZT of 1.35 at 393 K and an average ZT of 1.25 across 303–483 K, representing a significant improvement over pristine BST. Compared to prior reports, this work achieves superior average ZT while maintaining high electrical conductivity, addressing the longstanding bottleneck of thermal conductivity reduction without compromising carrier mobility. The findings underscore the efficacy of pseudo grain boundary engineering in advancing Bi2Te3-based thermoelectrics for solid-state cooling and power generation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4367-4
Single-crystalline Cs3Cu2I5 has attracted considerable interest owing to its excellent scintillation performance and favorable stability. Nevertheless, second phases induced by peritectic reactions during melt growth give rise to deteriorated scintillation properties and promote crystal cracking. In this work, the effects of non-stoichiometric ratios of raw material (n(CsI)=0.57, 0.62, and 0.63) on the crystallization behavior and scintillation properties were systematically investigated. The results show that the crystal quality is optimal at n(CsI)=0.62, featuring high transparency, absence of macroscopic inclusions, and cracking free, with a PLQY of 79.3%. Temperature-dependent photoluminescence verifies the self-trapped exciton emission mechanism with strong exciton-phonon coupling, giving an exciton binding energy of 473.9 meV and a Huang-Rhys factor S of 79.8. The as-grown crystal exhibits an optimized light yield of 24,380 photons/MeV, an energy resolution of 3.8% for 137Cs (662 keV) γ-rays, a dominant decay time of 957 ns, and excellent linear response in the medium-to-high energy region. Precise regulation of the raw material stoichiometry can effectively suppress the formation of second phases, yielding high-quality Cs3Cu2I5 single crystals whose comprehensive performance demonstrates promising application potential in γ-ray detection.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4292-4
The vast compositional space of high-entropy materials presents a fundamental challenge for catalyst discovery. Considering 21 candidate elements at a 1% atomic resolution, this combinatorial explosion exceeds 10 billion (>10^10) possibilities, rendering direct experimental exploration impractical. Furthermore, purely data-driven approaches often struggle to comprehend the intrinsic chemical roles of discrete elemental identities, yet they excel at mapping continuous concentration gradients. Recognizing this distinction, we transform this combinatorial explosion into a targeted optimization problem by decoupling elemental selection from compositional ratio refinement. Ultrafast carbon thermal shock (CTS) is first employed to screen viable elemental combinations and establish an optimal quinary framework. Machine learning (ML) is subsequently applied to optimize compositional ratios within this reduced space, where statistical modeling efficiently navigates the remaining high-dimensional landscape. Targeting the oxygen evolution reaction (OER) as a proof-of-concept, our hybrid framework pruned the search space from over 10^10 possible compositions down into 13 systems, ultimately identifying high-entropy oxide (HEO)-Fe17.57Co28.45Ni31.27Mo10.57Zr12.14 as the optimal catalyst. The optimized high-entropy oxide exhibits an overpotential of 240 mV at 10 mA cm−2 and sustains stable operation at 1 A cm−2 for over 600 h in 1 M KOH. Mechanistic analysis reveals that Mo electronically tunes oxygen-intermediate adsorption, while Zr enhances structural robustness, collectively enabling high activity and durability. This work demonstrates that bridging discrete physical screening with continuous data-driven optimization provides an efficient and generalizable pathway for navigating high-dimensional material frontiers.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4369-1
Sodium-ion batteries (SIBs) are promising alternatives to lithium-ion batteries for large-scale energy storage due to sodium's abundance and low cost. Among cathode materials, polyanionic compounds like Na3V2(PO4)2O2F (NVPOF) offer high energy density and dual voltage plateaus at ~3.6 and 4.0 V, but suffer from low electronic conductivity and sluggish Na+ diffusion. Here, we report a dual-modulation strategy combining high-valence Nb5+ doping and polydopamine-derived carbon coating to synthesize Na3V1.94Nb0.06(PO4)2O2F-C (NVPOF-Nb-C) via a hydrothermal route. X-ray diffraction and Rietveld refinement confirm that Nb5+ doping induces slight lattice expansion without altering the tetragonal I4/mmm framework. Density functional theory calculations reveal that Nb5+ doping optimizes the crystal structure and reduces the Na+ diffusion barrier, while the uniform carbon coating enhances electron transport. Consequently, NVPOF-Nb-C exhibits remarkably improved electrochemical performance, including high reversible capacity, excellent rate capability, and ultralong cycling stability. In a full cell with hard carbon anode, it delivers a high energy density of 487.2 Wh kg−1 at 1C and retains 91.51% capacity after 3000 cycles at 20C. This work provides a synergistic strategy to overcome the intrinsic limitations of polyanionic cathodes for practical SIB applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4262-7
The escalating demands of artificial intelligence, machine learning, and neural computing necessitate multifunctional optoelectronic devices capable of integrating sensing, memory, and processing. Two-dimensional van der Waals heterostructures (vdWHs) offer unique advantages, yet their practical deployment is hindered by complex architectures and inefficient mode-switching. Here, we demonstrate a MoTe2/SnS2 anti-ambipolar heterojunction device enabling single-gate reconfiguration among frequency doubling, broadband photodetection, and neuromorphic computing. The device exhibits a peak-to-valley ratio (PVR) of 465, ensuring efficient frequency doubling. As a photodetector, it operates across an exceptionally broad spectral range of 520–2200 nm, with outstanding responsivity and detectivity. Furthermore, the device emulates complete synaptic behaviors, including short-term plasticity (STP), long-term plasticity (LTP), and paired-pulse facilitation (PPF). Integrated into a reservoir computing (RC) system trained on a vehicle motion dataset, it achieves a directional recognition accuracy of 98.7%. This work establishes a paradigm for multifunctional integration and low-power neuromorphic computing, advancing next-generation intelligent optoelectronic systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4315-2
High-temperature X-ray imaging demands scintillators with high crystallinity, efficient scintillation, and robust thermal stability, yet suitable materials remain scarce. Here, we report an ultra-high-crystallinity transparent glass-ceramic (GC) scintillator strategically designed via controllable heat-treatment-induced crystallization. A sequential precipitation method is employed, where cubic CaF2 nanocrystals initially form, subsequently promoting heterogeneous nucleation and growth of hexagonal BaAl2Si2O8. Intrinsic nanoscale phase separation into F-rich and O-rich domains significantly reduces atomic diffusion distances, yielding an unprecedented crystallinity of up to 97.6%. Notably, defect traps (oxygen vacancy defects, likely located within the lattice or at crystalline/amorphous interfaces) enable efficient carrier capture and thermally stimulated release, contributing to remarkable resistance to thermal quenching. Consequently, the GC scintillator maintains 90.6% of its integrated X-ray excited luminescence (XEL) intensity at 300 °C, with the integrated XEL intensity reaching 94.2% of commercial Bi4Ge3O12 (BGO) at room temperature. This enables stable high-temperature X-ray imaging with a spatial resolution of ~10.4 lp mm−1 up to 225 °C. This work provides a versatile pathway for developing high-sensitivity scintillators for extreme-environment X-ray imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4236-8
Electrochemical nitrate reduction (NO3RR) to ammonia offers a sustainable route for nitrogen recovery from wastewater, yet its efficiency is constrained by complex multi-step proton-electron transfers and competitive hydrogen evolution. Here, we report a series of binary cobalt-copper phosphates with precisely tuned Co/Cu ratios, revealing a volcano-type relationship between composition and catalytic activity. The optimized Co0.5Cu1.5(OH)PO4 catalyst, supported on a Ni3Co1OxHy/Ni foam substrate, achieves a Faradaic efficiency of 99.0% for ammonia at a high current density of 200 mA cm−2 in 1 M nitrate electrolyte, with a production rate of 9.18 mg h−1 cm−2 and sustained stability over 200 hours. In-situ ATR-FTIR spectroscopy and density functional theory calculations elucidate a tandem mechanism: Co sites promote water dissociation to generate active hydrogen (H*), while adjacent Cu sites facilitate nitrate adsorption and subsequent hydrogenation steps. This synergistic division of labor lowers the energy barrier for the rate-determining step, effectively suppressing HER and enhancing intrinsic kinetics. The work demonstrates that precise atomic-ratio engineering in dual-site transition metal phosphates provides a viable strategy to overcome activity-selectivity trade-offs in electrocatalytic nitrate-to-ammonia conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4212-x
Idiopathic pulmonary fibrosis (IPF) is a lethal interstitial lung disease with limited therapeutic options. Current treatments, such as nintedanib and pirfenidone, target downstream fibrosis but fail to address the upstream drivers, including persistent alveolar epithelial injury and abnormal repair. This study presents an inhalable, reactive oxygen species (ROS)-responsive liposomal system (SAB/GC-1@Lip-cRGD) that co-delivers the antioxidant salvianolic acid B (SAB) and the thyroid hormone receptor β (TRβ) agonist Sobetirome (GC-1). The liposomes are surface-modified with cRGD peptides for targeted delivery to fibrotic lesions and possess a negative surface charge to enhance mucus penetration. In the high-ROS fibrotic microenvironment, the liposomes destabilize, releasing SAB and GC-1. SAB scavenges ROS to remodel the fibrotic niche, while GC-1 reactivates TRβ signaling, driving the differentiation of stalled Krt8+ transitional epithelial cells into functional alveolar type I (AT1) cells. In a mouse model of pulmonary fibrosis, SAB/GC-1@Lip-cRGD significantly reduced pro-inflammatory cytokines (TNF-α, IL-1β, IL-6) and TGF-β1 in bronchoalveolar lavage fluid and lung homogenates. The proportion of CD206+ M2 macrophages decreased from 27.4% in the model group to 6.2% after treatment, indicating potent anti-inflammatory and anti-fibrotic effects. This synergistic strategy of microenvironment remodeling and epithelial regeneration achieved robust collagen depletion, restoration of alveolar integrity, and recovery of pulmonary function, outperforming single-drug or non-targeted formulations. The work provides a generalized paradigm for integrating microenvironment regulation with regenerative repair in pulmonary diseases.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4235-6
Fluorite-structured oxides (HfO2, ZrO2) are promising for resistive random-access memory (RRAM) due to their scalability and tunable properties. However, achieving high resistive switching on/off ratios remains challenging. Here, we report a collaborative strategy combining Hf/Zr ratio optimization and Lu3+ doping to regulate band structure and oxygen vacancy concentration in Hf0.4Zr0.6O2 (LHZO) thin films. The resulting LHZO devices exhibit a resistive switching ratio of 8.4 × 10^4, two orders of magnitude higher than that of ZrO2 (1.2 × 10^3). Electrical characterization and synchrotron radiation photoemission spectroscopy reveal that Lu doping widens the bandgap to 4.95 eV, downshifts the valence band, and introduces defect states, collectively suppressing p-type conductivity and reducing off-state leakage current. Simultaneously, Lu3+ doping enriches oxygen vacancies, stabilizing ohmic conductive filaments in the on-state. This co-optimization of band structure and oxygen vacancies effectively enhances insulating properties in the high-resistance state and ohmic conductivity in the low-resistance state, leading to superior resistive switching performance with robust retention (>10^4 s). Our findings establish a fundamental strategy for tailoring electronic properties of doped HfZrO2 thin films toward high-performance RRAM applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4176-y
Three-photon microscopy (3PM) in the near-infrared-III (NIR-III) window (1600–1840 nm) enables high-resolution visualization of cerebral vasculature in vivo, but its imaging depth and quality are limited by the performance of fluorescent probes. Here, we report a probe optimization strategy transitioning from mirror symmetry to centrosymmetry, yielding a highly symmetric aggregation-induced emission (AIE) molecule, T4PQ. The centrosymmetric structure aligns donor-acceptor units, promoting uniform electron cloud delocalization and directional charge transfer, which enhances exciton formation and suppresses non-radiative decay, thereby increasing fluorescence quantum yield. This symmetry also boosts the three-photon absorption cross-section by enhancing electron delocalization and transition dipole moment, enabling stronger nonlinear optical responses under long-wavelength excitation. T4PQ nanoparticles (T4PQ NPs) exhibit an enhanced three-photon absorption cross-section, high fluorescence quantum yield, and excellent photostability. In murine models, T4PQ NPs achieved three-dimensional cerebrovascular imaging at a depth of 1785 μm and real-time hemodynamic observation in microvessels at 1006 μm depth, with good biocompatibility. These results validate the advantage of centrosymmetric molecular design for deep-brain imaging probes, offering a high-performance tool for neurovascular research.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4180-9
Developing highly active and stable electrocatalysts based on the lattice oxygen mechanism (LOM) for the oxygen evolution reaction (OER) represents a significant challenge in water splitting. Herein, we successfully introduce oxygen vacancies (Ov) into high-entropy MnFeCoNiCu layered double hydroxides (HE-LDHs) via a solution chemical reduction method utilizing a defect engineering strategy. By precisely tuning the concentration of oxygen vacancies, we effectively activate the lattice oxygen within the HE-LDHs. The optimized Ov-rich high-entropy LDHs (Ov-HE-LDHs) exhibit excellent OER catalytic performance, achieving a current density of 10 mA cm−2 with a remarkably low overpotential of only 210 mV in 1.0 M KOH electrolyte, which is substantially superior to pristine HE-LDHs (315 mV) and commercial IrO2 (330 mV). Furthermore, the catalyst demonstrates outstanding long-term stability, capable of stable operation for 500 h at a high current density of approximately 200 mA cm−2. Advanced X-ray absorption fine structure analysis elucidates the lower metal valence states, indicating the existence of oxygen vacancies, while isotope labeling experiments and in-situ electrochemical Raman spectroscopy strongly confirm the successful activation of the LOM pathway. Density functional theory calculations further validate that the shift in the OER mechanism towards LOM and the resulting reduction in the reaction energy barrier are the fundamental reasons for the catalyst’s enhanced intrinsic activity. This work proposes a novel strategy for activating lattice oxygen in high-entropy LDHs through defect engineering, offering new insights and experimental guidance for the design and development of highly efficient and stable high-entropy OER electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4317-4
This correction addresses an image assembly error identified in Fig. 7a of the original article published in Science China Materials, volume 66, issue 6, 2023, pages 2513–2522. The error was confined to the assembly of images in Fig. 7a, which presents H&E staining analysis of major organs from a toxicity study. The corrected version of Fig. 7 is provided in this corrigendum. The original study evaluated the toxicity of lyophilized cabazitaxel (CTX) and Tween 80-based CTX formulations in CD-1 mice following a single intravenous administration of 30 mg kg−1 CTX via the tail vein on day 0, with sacrifice on day 14 for analysis (n=5). The figure includes H&E staining of major organs, complete blood count (CBC) analysis with statistical significance indicated by *p < 0.05, and mouse weight measurements. The correction does not affect the overall results, data interpretation, or scientific conclusions of the original article. All authors have reviewed and approved the content of this corrigendum. The authors sincerely apologize for any inconvenience caused to the editorial office, reviewers, and readers. The article was received on 6 May 2026, accepted on 4 June 2026, and published online on 31 July 2026.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4112-6
Radiostrontium remediation is crucial for ecological protection and sustainable development of nuclear energy. However, efficient removal of 90Sr from complex radioactive liquid waste, especially under acidic conditions, remains challenging due to material instability and intense proton competition. Herein, the rapid and highly selective capture of Sr2+ in neutral and even acidic solutions has been achieved by a layered potassium phosphatoantimonate KSbP2O8 with excellent radiation and thermal stability. Under neutral conditions, it possesses high maximum adsorption capacity (qmSr = 110.25 mg g−1), rapid adsorption kinetics (the removal rate (RSr) of 91.54% within 30 min), and excellent selectivity for Sr2+, and facile regeneration. Particularly, even under acidic conditions (pH 2.0), KSbP2O8 still maintains excellent Sr2+ removal capacity (qmSr = 79.38 mg g−1), fast kinetics, and high selectivity. A mechanism study by multiple characterizations reveals that the efficient Sr2+ removal of KSbP2O8 mainly stems from ion exchange between Sr2+ and interlayer K+ in KSbP2O8, which is attributed to the synergy between the Sb5+-induced Brønsted acidity and the high charge density of the anionic framework. This study demonstrates the exceptional capability of phosphatoantimonates to selectively capture Sr2+ under acidic conditions, highlighting the potential of phosphatoantimonates as effective scavengers for radiostrontium remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3696-3
The development of substitutable meniscus implants that can effectively protect articular cartilage remains a great challenge. Herein, a polyurethane with chemical crosslinking and sulfobetaine extenders containing hydrophobic chains (PU-CL-hSB) is developed, which could improve comprehensive properties and long-term stability simultaneously. By regulating the mole ratio of functional groups, PU-CL-hSB with appropriate mechanical properties, excellent tribological properties, and good fatigue resistance is used to prepare substitutable meniscus implant by hot-pressing. Due to the synergistic effect of functional groups, PU-CL-hSB meniscus implant presents comparable or even superior properties to native meniscus. It withstands a maximum force of 26.08 N versus 25.14 N for native meniscus, an energy dissipation from 45.93 to 39.17 N mm compared to 28.83 to 19.11 N mm for native meniscus over 300 cycles, and a friction coefficient from 0.08 to 0.19 compared to 0.11 to 0.26 for native meniscus. This PU-CL-hSB meniscus implant is further implanted into live rabbit knee joints for 8 and 25 weeks by a new approach, and in vivo data indicate that PU-CL-hSB meniscus implant not only protects articular cartilage from severe damage without eliciting inflammatory responses, but also can maintain normal physiological activities in the native state. Our findings present a substitutable meniscus implant that could be applied in vivo and propose evaluation methodologies for meniscus implants.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4197-4
Deep-blue organic light-emitting diodes (OLEDs) remain the most challenging primary-color emitters due to stringent exciton energy requirements. We strategically designed two innovative deep-blue emitters, SCZ-4AnCN and STPA-4AnCN, via systematic functionalization of an anthracene core with arylamino-decorated spirofluorene donors and cyano-substituted phenyl acceptors. Comprehensive theoretical and experimental analyses demonstrate that these spirofluorene-anthracene hybrids adopt precisely engineered distorted configurations, effectively suppressing detrimental intermolecular π–π stacking in condensed phases. The sp3-hybridized bridgehead carbons in spirofluorene units play a pivotal role by simultaneously restricting π-conjugation extension and fine-tuning donor–acceptor interactions, thereby stabilizing the lowest excited singlet (S1) state with dominant local excitation (LE) character. This molecular engineering yields exceptional deep-blue emission with remarkable efficiency. Notably, the materials exhibit unique high-lying reverse intersystem crossing (hRISC) behavior, enabling efficient triplet harvesting. Optimized doped devices incorporating SCZ-4AnCN achieve outstanding performance, including a maximum external quantum efficiency (EQE_max) exceeding 10% and CIE coordinates (0.154, 0.052) approaching the BT.2020 blue standard. Nondoped devices maintain impressive performance with an EQE_max of 7.51% and superior operational stability, demonstrating less than 10% efficiency roll-off at 1000 cd m−2. This work validates anthracene-based molecular architectures for deep-blue electroluminescence and establishes a transformative design paradigm for next-generation OLED emitters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4199-8
High-entropy borides (HEBs) represent an emerging class of high-entropy materials that have garnered significant attention as ultra-high-temperature ceramics (UHTCs). By leveraging the high configuration entropy effect, HEBs stabilize single-phase solid solutions, exhibiting a suite of properties unattainable in traditional binary borides. This review systematically consolidates research progress on HEBs, beginning with theoretical predictions and component design via first-principles methods. It then details typical HEB systems and principal synthesis techniques, including arc melting and spark plasma sintering. The core analysis evaluates the outstanding performance of HEBs, emphasizing exceptional mechanical properties such as ultra-high hardness and excellent fracture toughness, alongside high-temperature friction and wear behavior, and oxidation resistance. Finally, the review outlines application prospects in extreme environments like aerospace and cutting tools, while also addressing current challenges. The paper underscores the potential of HEBs to overcome the hardness-toughness trade-off inherent in conventional ceramics, driven by strong metal-boron hybridization. This comprehensive overview positions HEBs as promising candidates for next-generation thermal and mechanical protection systems, with future research directions focusing on optimizing compositions and processing to tailor properties for specific applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3775-3
The urgent imperative for carbon-neutral chemical production has accelerated the development of solar-driven catalytic technologies that convert abundant C1 feedstocks (CO2 and CH4) into value-added C2+ molecules. Standalone photocatalysis remains constrained by rapid charge-carrier recombination and poor C–C coupling selectivity. This review critically examines multi-field-coupled catalysis—a transformative paradigm synergistically integrating solar energy with auxiliary thermal, electric, and magnetic fields. Through mechanistic dissection of photothermal, photoelectrochemical, and photomagnetic field cooperativities, it is summarized that thermal gradients attenuate phonon scattering to enhance charge-carrier drift mobility while vibrationally stabilizing reactive intermediates, electric potentials drive vectorial charge transport via Coulomb-force-directed separation and band alignment, and magnetic fields modulate spin-selective electron transfer through Zeeman splitting-mediated polarization to boost reaction specificity. This synergistic multi-field integration circumvents intrinsic limitations of single-mode photocatalysis by collectively reconfiguring reaction coordinates for selective C–C coupling. We further address persistent challenges in resolving ultrafast interfacial charge-transfer dynamics, scaling integrated field reactors for industrial deployment, and advancing in situ operando characterization of multiscale processes. Strategic research priorities are proposed to advance sustainable multi-field-coupled catalytic production of fuels and platform chemicals.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4153-2
Direct seawater electrolysis offers a promising route to green hydrogen production, circumventing freshwater scarcity. However, the presence of chloride ions (Cl−) poses severe challenges, including competing chlorine evolution reaction (CER) and corrosion of anode catalysts. Here, we report a dual-atom catalyst design, RuCr-Ni3P, where Ru atoms with strong chloride affinity and Cr atoms as Lewis acid centers are co-doped into a nickel phosphide matrix. This catalyst exhibits outstanding oxygen evolution reaction (OER) activity and selectivity in alkaline seawater, achieving stable operation for over 4000 hours at industrially relevant current densities. Mechanistic studies reveal that Cl− ions are selectively captured by Ru sites, forming a dynamic Ru–Cl coordination motif that electronically modulates adjacent Ni centers, promoting the formation of high-valent Ni>3+ species. This switches the OER pathway from the lattice oxygen mechanism (LOM) to the more efficient adsorbate evolution mechanism (AEM). Concurrently, Cr sites facilitate the formation of Cr–OH species, creating a localized alkaline microenvironment that further enhances OER kinetics. This dual-site synergistic mechanism transforms Cl− from a detrimental impurity into a beneficial chemical switch, concurrently enhancing both activity and stability. Our findings provide a paradigm shift in seawater electrolysis catalyst design, turning a longstanding challenge into an opportunity for efficient and durable hydrogen production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3608-8
Polymeric carbon nitride (PCN) is a promising photocatalyst for H2O2 production due to its visible-light response, low cost, and high selectivity for the two-electron oxygen reduction reaction (ORR). However, its H2O2 yield is limited by narrow light absorption, low charge separation efficiency, and insufficient active sites. Here, crystalline poly(heptazine imide) (PHI)-based carbon nitride with highly dispersed In sites and N defects was prepared via an ionothermal method using LiCl/KCl molten salts. The large π-conjugated system and N defects enhance visible-light harvesting. Remaining K+ ions in nitrogen cavities act as interlayer electron channels, while N defects induce asymmetric charge distribution on the heptazine network, promoting interlayer and in-plane charge separation and transfer. In sites accelerate charge transfer dynamics and serve as active sites for ORR. The synergistic effect of metal modification and defect engineering boosts electron delocalization, significantly improving photocatalytic activity. The H2O2 production rate of 10InPHI reaches 15.3 mmol g−1 h−1 via a two-step single-electron ORR pathway, underscoring the potential of modified carbon nitride for efficient H2O2 photosynthesis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3803-8
The molecular copolymerization of donor-acceptor (D-A) interactions has been effectively utilized to modulate the charge transfer dynamics in polymeric carbon nitride (PCN) photocatalysts. Herein, a D-A configured photocatalyst (TPCN) was constructed by copolymerizing 4,4’,4’’-(1,3,5-triazine-2,4,6-triyl) trianiline (TAPT) as the electron donor with triazine units (electron acceptor). The unique propeller structure of TAPT, combined with the triazine framework, expanded the π-conjugated system and induced a strong built-in electric field (BIEF) across the D-A configuration. Theoretical calculations and transient absorption spectroscopy revealed that this synergistic effect facilitated intramolecular charge separation and widened the range of light absorption, indicating accelerated charge transfer and suppressed recombination in TPCN. The optimized TPCN3 sample exhibited dramatically enhanced photocatalytic H2O2 production (1.74 mmol g−1 h−1), representing a 13.4-fold increase over pristine PCN. Additionally, the TPCN3 sample also exhibited significantly faster degradation kinetics than PCN counterpart toward various emerging contaminants. This work demonstrates a promising strategy for designing efficient metal-free photocatalysts for sustainable H2O2 production and environmental remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3564-9
Sluggish water dissociation kinetics in the alkaline hydrogen evolution reaction (HER) hamper its practical production. Here, a heterojunction electrocatalyst featuring Ru-Ni(OH)2 interfaces on nickel foam (NF) with self-engineered built-in electric fields (BIEF) was synthesized via a simple in situ galvanic replacement reaction. The hierarchical Ru-Ni(OH)2/NF exhibits a record overpotential of 9.6 mV at 10 mA cm−2 for alkaline HER, surpassing most reported catalysts and commercial Pt/C. It also shows exceptional activity for hydrazine oxidation reaction (HzOR) at 100 mA cm−2 with a remarkably low potential of ca. 0.015 V vs. RHE. The assembled overall hydrazine splitting (OHzS) system integrating HER and HzOR requires a cell voltage of about 0.09 V to reach 50 mA cm−2, which is 1.637 V lower than the corresponding overall water splitting (OWS) device. Systematic analysis and calculation reveal that the BIEF induces redistribution of interfacial electrons for Ru, facilitating H2O dissociation and intermediate conversion, delivering ultra-high electrocatalytic performance. This work provides an avenue for design and preparation of electric field-mediated catalysts towards sustainable energy conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3553-7
Gesture interaction has emerged as a highly effective interface for intelligent human-computer interaction, attributed to its intuitive interaction modality and multi-dimensional control capabilities. However, traditional gesture interaction devices often depend on predefined encoding rules, which substantially limit interaction efficiency and degrade user experience. This study introduces an innovative intelligent finger ring interaction system based on a triboelectric nanogenerator utilizing PDMS/SrTiO3 composite thin film (PS-TENG). The system maps freehand writing gestures directly to textual information input, thereby eliminating the need for complex gesture encoding schemes and offering a user-friendly, low-learning-curve input method. By integrating a deep learning model, the system achieves recognition accuracies of 98.21% for English letters, 96.87% for Arabic numerals, and 96.44% for Chinese characters. Furthermore, it supports secure and encrypted data transmission and enables wireless interaction for gaming control. These findings indicate that the intelligent finger ring interaction system possesses significant potential for practical applications in information input and wireless control.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3645-3
Postoperative abdominal adhesion, a complication with morbidity exceeding 90%, imposes severe clinical and economic burdens. Existing bioadhesive barriers often exhibit unreliable adhesion to the slippery abdominal wall, risk mispositioning, and neglect frictional stimuli and inflammation. Inspired by the lubricated peritoneum, we developed a programmable adhesive dual-layer Janus patch (DJP) barrier integrating a lubricated layer and an adhesive matrix. DJP achieves rapid, noncovalent interfacial adhesion, subsequently enhanced 2.81-fold via covalent interactions, enabling repositioning within a short time window to improve surgical fault tolerance. The micron-scale poly(sulfobetaine methacrylamide) brush on the DJP surface provides hydration lubrication with a low coefficient of friction (0.06), mimicking peritoneal lubrication and reducing frictional damage to injured tissue. The catechol-containing copolymer confers antioxidative and anti-inflammatory properties, confirmed in vitro. In a rat model, DJP adhering to the injured site significantly reduced collagen deposition between the abdominal wall and cecum, preventing adhesion and promoting tissue healing compared to commercial barriers. This work provides a guiding reference for developing antiadhesive biomaterials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3432-8
This correction addresses an error in the labeling of author affiliations in the original publication (Sci China Mater, 2025, 68: 1561, DOI: 10.1007/s40843-024-3290-9). The corrected affiliations are as follows: Fuxia Huang, Feng Wang, Ya Liu, and Liejin Guo are affiliated with the International Research Center for Renewable Energy, State Key Laboratory of Multiphase Flow in Power Engineering, Xi'an Jiaotong University, Xi'an 710049, China. Yifei Liu is affiliated with the School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240, China. The correction was made upon the request of the authors and with approval from the respective institutions. The original article focused on crystal defects engineering of BiOI to enhance photocatalytic CO2 reduction to C2 products, a critical area for sustainable fuel synthesis. This correction ensures accurate attribution and institutional recognition, which is essential for research integrity and reproducibility. No changes were made to the scientific content or conclusions of the original study.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3623-y
Organic light-emitting diodes (OLEDs) are an advanced technology for full-color displays, yet the low efficiency of blue OLEDs remains a critical bottleneck. Here, we report a new strategy to design robust Pt(II) emitters with enhanced molecular rigidity and increased locally excited character. The resulting Pt(II) emitter exhibits an extremely narrow emission spectrum peaking at 458.6 nm with a full-width at half-maximum (FWHM) of 16.0 nm and a small Huang-Rhys factor of 0.278, together with a high photoluminescence quantum efficiency of 95%. When doped into an OLED, the device emits at 464 nm with high color purity (FWHM = 19 nm) and achieves high external quantum efficiencies (EQEs) of 32.6%, 29.4%, and 26.9% at luminances of 123, 1000, and 5000 cd/m2, respectively. Notably, the device attains a record-high maximum brightness of 84,895 cd/m2 among reported deep-blue OLEDs with Commission Internationale de l'Éclairage (CIE) y-coordinate < 0.15. This work demonstrates one of the highest-performing deep-blue OLEDs reported to date, addressing the dual challenges of efficiency and brightness in this spectral region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3677-9
The demand for high-performance scintillators in high-temperature applications, such as industrial flaw detection and oil exploration, necessitates materials with both high efficiency and thermal robustness. This work reports Tb3+-doped oxyfluoride glass scintillators exhibiting anti-thermal-quenching radioluminescence (RL). Three synergistic strategies were employed: (i) an oxyfluoride glass host providing a low-phonon-energy environment, (ii) increased structural densification of the glass network, and (iii) thermally enhanced energy transfer from Ce3+ to Tb3+. The resulting scintillators achieve an optical transmittance exceeding 88% at 542 nm, a record RL intensity of 350% relative to a standard Bi4Ge3O12 (BGO) crystal, and an imaging resolution of 24 lp mm−1. Notably, the RL intensity at 633 K reaches 143% of its room-temperature (303 K) value, demonstrating significant anti-thermal-quenching behavior. In contrast, commercial BGO and CsI:Tl scintillators exhibit RL intensities dropping to approximately 1% under identical conditions. These results establish the potential of Tb3+-doped glass scintillators for high-temperature X-ray imaging and provide a strategic framework for developing thermally robust scintillating materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3706-3
Aprotic lithium-oxygen (Li-O2) batteries are severely limited by slow cathode reaction kinetics and large polarization. Herein, we design and prepare a Mott-Schottky catalyst by uniformly embedding ultrafine Ru nanoparticles on nitrogen-doped carbon (Ru@NC) nanoflakes to accelerate oxygen redox kinetics of Li-O2 batteries. The Mott-Schottky effect of Ru@NC drives spontaneous electron rearrangement in the NC matrix and induces a strong built-in electric field at heterointerfaces, which accelerates the activation and conversion of oxygen intermediates. The obtained Ru@NC possesses rich Mott-Schottky heterointerfaces and defective carbon structures, which provide extensive adsorption and nucleation sites. More importantly, Ru@NC manifests moderate affinity for the intermediate LiO2, inducing formation of unique nanosheet-like Li2O2 with low Li2O2/cathode interfacial impedance, which further enhances oxidation kinetics. These enable the Li-O2 battery with Ru@NC to deliver a remarkably reduced polarization of 0.89 V, superior rate performance, and prolonged lifespan of over 200 cycles. This work will provide valuable guidelines for engineering advanced electrocatalysts for high-performance Li-O2 batteries and beyond.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3746-x
The polyanionic compound Na3V2(PO4)2O2F (NVPOF) possesses a stable three-dimensional framework, high theoretical specific capacity, and favorable operating voltage, yet its sluggish Na+ diffusion kinetics and low electronic conductivity impede industrial application. This study proposes a dual regulation strategy combining carbon coating and heat treatment temperature to synergistically enhance crystallinity and electrochemical performance. NVPOF@C-400 and NVPOF@C-600 were synthesized via in-situ dopamine hydrochloride coating followed by heat treatment at 400 °C and 600 °C, respectively. Carbon coating at 600 °C significantly improved crystallinity and increased electronic conductivity by three orders of magnitude through the carbon layer's conductive network. The ~4.5 nm carbon layer effectively suppressed abnormal grain growth and secondary crystallization aggregation at high temperatures, maintaining uniform particle size of approximately 0.36 μm, which shortens Na+ diffusion pathways and prevents ion transport obstruction. Consequently, NVPOF@C-600 delivered a high discharge capacity of 102.5 mAh g−1 at 20 C and retained 96.5% capacity after 10,000 cycles. In a full-cell configuration with hard carbon (HC), NVPOF@C-600//HC achieved an impressive 89.3% capacity retention after 9,000 cycles. This work provides critical insights for practical implementation of high-performance NVPOF cathodes in sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3506-3
Metallic glasses (MGs) often suffer from sluggish hydrogen evolution reaction (HER) kinetics in neutral and alkaline media, with their catalytic performance predominantly confined to acidic environments. Herein, we reported a novel thermoplastic forming technique to fabricate a self-supported partially crystallized nanoporous Pt56.2Ni5.2Cu16.8P21.8 metallic glass (C-NPMG). The C-NPMG catalyst delivers ultralow overpotentials of 18.0 mV (0.5 M H2SO4), 42.2 mV (1 M KOH), and 88.0 mV (1 M phosphate-buffered saline (PBS)) at a current density of 10 mA cm−2, outperforming most state-of-the-art non-noble MGs and Pt-based benchmarks across all pH conditions. Notably, it maintains negligible performance decay for over 1000 h in alkaline electrolytes, showcasing superior stability. Experimental and computational analyses reveal that the enhanced HER activity arises from three synergistic effects: (1) the high-specific-surface-area nanoporous architecture that maximizes active site exposure; (2) the formation of crystallite-amorphous interfaces during partial crystallization, which lowers the energy barrier for H2 desorption; (3) the hierarchical super-hydrophilic and super-hydrophobic wettability of the C-NPMG, which optimizes mass transport and prevents electrolyte-induced corrosion. This work establishes a novel design paradigm for developing high-performance, pH-universal HER electrocatalysts by integrating structural nano-engineering and crystallite-amorphous phase synergy in metallic glass systems to overcome the trade-offs between performance and stability in electrochemical water splitting.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3695-8
Sulfur-based lithium-ion batteries, particularly those employing sulfurized poly(acrylonitrile) (SPAN) cathodes and graphite (Gr) anodes, offer high theoretical capacity and low cost but suffer from temperature-dependent capacity decay. This study systematically investigates the electrochemical dynamics and capacity decay mechanism of SPAN||Gr pouch cells cycled at 25–55 °C. Multiscale analyses reveal that capacity fade arises from active lithium loss and increased resistance, both accelerated by higher temperatures. Active lithium loss is primarily attributed to dead lithium formation and thickening of the solid electrolyte interphase (SEI) and cathode electrolyte interphase (CEI), while resistance increase is predominantly due to SEI/CEI thickening. As temperature rises, active lithium loss becomes the dominant decay factor. Leveraging the consistent decay mechanism across temperatures, an accelerated aging model based on the Arrhenius equation is developed: y = 0.9x + a. This model accurately predicts cycling parameters at specific temperatures and reduces testing time by 50% when extrapolating from 55 °C to 25 °C. These insights provide critical guidance for developing long-life sulfur-based batteries for practical energy storage applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3652-2
Existing robotic end-effector gripping technologies often encounter challenges such as poor adaptability to environmental changes, incomplete deformation sensing, and insufficient adhesion stability, which can compromise operational safety and reliability. Here, we present the bio-inspired self-sensing suction cup, in which the core self-sensing capability is achieved by combining high-performance, laser-induced graphene/Ag NWs flexible sensors with a Wheatstone bridge design. The flexible sensors provide high sensitivity, while the Wheatstone bridge circuit enables accurate and stable detection of deformation during the gripping process. Integrated into the octopus-inspired suction cup, this system allows for real-time monitoring of deformation and adsorption stability. The self-sensing suction cup demonstrates good performance across a 0–25 kPa negative pressure range, with outstanding linearity (R2 = 0.993) and high sensitivity (GF = 10.436 kPa−1). Experimental results confirm that the suction cup can achieve stable adsorption under varying loads and enable real-time monitoring of the suction cup status during the gripping process. This design provides a promising solution for intelligent gripping systems, logistics, and object recognition in challenging environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3649-0
Injectable hydrogels formed via dynamic chemical crosslinks hold great promise as drug delivery platforms due to their robust yet adaptable nature, stimuli-responsiveness, and tunable structures and properties. However, their inherently high water content poses a significant challenge for the efficient encapsulation and sustained release of hydrophobic drugs. Here, we present a novel injectable hydrogel system constructed via a strain-promoted disulfide-thiol exchange between dithiolane-functionalized polymer strands and thiolated core-shell nanoparticles (NPs) under physiological conditions. The hydrophobic core and hydrophilic shell structure of the NPs enables effective loading and protection of hydrophobic drugs, while rapid gelation occurs upon mixing the thiolated NPs with dithiolane-polymers in phosphate-buffered saline. The hydrogel shows excellent injectability, self-healing capability, in vitro biodegradability, and cytocompatibility. This hydrogel system enables sustained release of hydrophobic drugs over 32 days in aqueous media and supports sequential dual-drug release. Its redox-responsiveness under tumor-mimicking reducing conditions, enabled by the disulfide crosslinks, further facilitates controlled intracellular drug release. This multi-component platform offers a versatile strategy for designing advanced injectable hydrogels with potential applications in hydrophobic drug delivery and other biomedical fields.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3586-7
Ischemic stroke is a leading cause of mortality and long-term disability worldwide, with endovascular stent intervention emerging as a key therapeutic strategy. Biodegradable Mg-Zn-Y-Nd alloy (ZE21B) offers promising mechanical properties and biocompatibility for vascular scaffolds, yet suffers from inadequate corrosion resistance, insufficient endothelialization, and impaired blood-brain barrier remodeling. This study develops a composite coating comprising barnacle cement protein cp19k and sulfonated hyaluronic acid nanoparticles (NP@S-HA) applied via electrostatic spraying onto ZE21B. The cp19k/NP@S-HA coating enhances corrosion resistance by approximately 40.6% relative to uncoated ZE21B, as determined by electrochemical and static immersion tests. In vitro blood and cellular assays demonstrate that the coating promotes endothelial cell proliferation and migration, inhibits smooth muscle cell proliferation while regulating contractile phenotype, suppresses macrophage adherence and induces M2 polarization, reduces TNF-α expression, and mitigates fibroplasia. These findings indicate that the cp19k/NP@S-HA composite coating provides an effective surface modification strategy for biodegradable magnesium alloys in cerebrovascular applications, potentially improving stent performance and patient outcomes.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(25)61036-5
Large graphene oxide (LGO) sheets offer significant advantages over smaller ones in various applications, yet their production via Hummers-type oxidation of large natural graphite flakes remains challenging due to difficulties in achieving full oxidation and avoiding fragmentation. This study provides the first direct evidence that large graphite flakes (up to 1 mm) can be completely oxidized without fragmentation under static conditions, as revealed by in-situ monitoring. The oxidation process is governed by diffusion of the oxidizer between layers, described by Fick's law, where a high oxidizer concentration gradient increases the diffusion rate. By minimizing the amount of concentrated H2SO4 solvent, we achieved a semi-solid state that elevates oxidizer concentration, facilitating Mn(VII) diffusion and enabling complete oxidation of gram-scale large flakes with significantly reduced reagent consumption. Reaction temperature was optimized to balance graphite oxidation and Mn(VII) self-decomposition. Using this approach, 200-, 100-, and 50-mesh natural graphite were fully oxidized with reduced H2SO4 and KMnO4 usage. After exfoliation, LGO with average lateral sizes of 27.3, 58.7, and 116.2 μm were obtained, respectively, with 100% conversion and yield over 165%. This work not only provides a scalable, cost-effective strategy for LGO production but also advances the fundamental understanding of Hummers-type oxidation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3748-9
Direct regeneration is a sustainable solution for recycling spent lithium-ion batteries (LIBs), yet the irregular strains induced by the irreversible FePO4 phase after cycling hinder Li+ replenishment in spent LiFePO4 cathodes. This study proposes a lattice stress modulation strategy that reduces FePO4 to Fe2P2O7, reducing unit cell volume from 271.7 to 122.6 Å3, releasing residual stress and reconstructing continuous Li+ transport channels. The phase transformation reconstructs FeO6 octahedra, lowering the migration energy barrier for ions. This synergistically weakens steric effects, facilitating Li+ replenishment and eliminating Li-Fe anti-site defects. Regenerated LiFePO4 cathodes achieve 80.2% capacity retention after 1000 cycles at 2C, outperforming commercial cathodes. The work establishes fundamental principles for the pre-treatment stage of direct regeneration and provides a paradigm-shifting solution for sustainable LIB recycling.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3807-8
Electrocatalytic co-reduction of CO2 and nitrate offers a sustainable route for urea synthesis, valorizing nitrogenous waste and CO2. However, achieving high-performance urea electrosynthesis under ambient conditions remains challenging due to the need for simultaneous activation of CO2 and efficient H2O dissociation to supply active *H for *NOx hydrogenation, ultimately forming key C- and N-containing intermediates for C–N coupling. Here, we report a bifunctional Pd-single-atom-modified Cu (Pd1Cu) nanorod catalyst that synergistically promotes adsorption and stepwise activation of CO2 and H2O, steering the reaction pathway toward selective urea synthesis. Integrating experimental evidence, in situ spectroscopy, and computational analyses, we disclose that atomically dispersed Pd sites kinetically favor co-generation of *CO and *NH2 via H2O dissociation-driven proton transfer, forming an optimal intermediate balance. The dual metal active sites enhance C–N coupling via combined electronic and geometric effects, substantially lowering the reaction energy barrier and improving selectivity. This work provides a rational design strategy for advanced multifunctional catalysts for urea electrosynthesis, contributing to carbon neutrality and waste nitrogen valorization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3815-0
The development of bifunctional electrocatalysts capable of integrating biomass-derived platform molecule oxidation with organic reduction offers a promising strategy for simultaneously enhancing energy efficiency and generating high-value chemicals. However, designing catalysts that exhibit both high activity and stability in integrated systems remains a significant challenge. Herein, we report a self-supported electrode composed of nitrogen-doped carbonized wood (NCW) supported NiCo nanosheets (NiCo 0.3/NCW) that enables the electrocatalytic 5-hydroxymethylfurfural oxidation to produce 2,5-furandicarboxylic acid (FDCA) and the nitrobenzene reduction to yield aniline in an integrated electrochemical cell. The NiCo 0.3/NCW electrode achieves the production of FDCA and aniline at a low cell voltage of 1.7 V, with ~99% anodic and ~92% cathodic Faradaic efficiencies, respectively. Experimental characterizations disclose that the hierarchical porous NCW architecture promotes the dispersion of active sites, while nitrogen doping strengthens metal–support interactions. In-situ spectroscopic experiments combined with density functional theory (DFT) calculations reveal that cobalt incorporation tunes the electronic structure of nickel, thus optimizing substrate and intermediate adsorption, and lowering energy barriers. These effects ultimately enhance the performance of the natural wood-derived catalyst in integrated biomass valorization and selective organic electrosynthesis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3713-y
Layered double hydroxides (LDHs) are promising electrocatalysts for the oxygen evolution reaction (OER), yet their practical application remains limited by poor electrical conductivity and sluggish reaction kinetics. In this work, we synthesize three high-entropy LDHs (HELDHs) featuring a hierarchical architecture of microspheres assembled from ultrathin nanosheets, via a simple hydrothermal method using a combination of low-cost, catalytically active transition metals (Fe, Co, Ni, Mn, Zn, Cu, and Cr). Among them, the FeCoNiMnZn HELDH exhibits outstanding OER performance, requiring an overpotential of only 306 mV to reach a current density of 100 mA cm−2. Notably, during 200 h of continuous operation, the device exhibits a stable and, in some cases, increasing current output. This exceptional activity is attributed to the formation of abundant cation vacancies, induced by Zn leaching, which enhance the intrinsic catalytic properties by optimizing the adsorption energies of key OER intermediates. Density functional theory calculations further validate that these vacancies modulate the electronic structure and lower reaction barriers, underscoring the effectiveness of cation-vacancy engineering in high-entropy systems for efficient and durable water oxidation catalysis. The optimized catalyst was further evaluated as the air cathode in a zinc–air battery, demonstrating practical electrochemical performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3725-1
Conductive hydrogel-based stretchable electronics have been extensively investigated, with strain sensors being the most prominently studied. While mechanical properties significantly affect device performance, the systematic correlation between specific mechanical parameters and sensing performance remains rarely explored. This work compares the influences of Young’s modulus and mechanical hysteresis on sensing performance between highly entangled PAM-Li and double-network PAM-Li-Agar-3 strain sensors. Owing to the brittle agar network, which imparts a higher Young’s modulus and pronounced mechanical hysteresis to the double-network PAM-Li-Agar-3 hydrogel, the corresponding sensor requires a greater driving force for deformation and yields signals with poor reproducibility. In contrast, the PAM-Li hydrogel, characterized by highly entangled polymer chains, exhibits a lower Young’s modulus and negligible mechanical hysteresis. Consequently, signals from the PAM-Li strain sensor demonstrate enhanced sensitivity and stability. Therefore, this work demonstrates that a low Young’s modulus and minimal mechanical hysteresis are critical factors for achieving superior sensing performance in strain sensors, as systematically validated through comparative analyses across diverse application scenarios.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506081
Advanced oxidation processes (AOPs) are promising for degrading organic pollutants in water treatment. Heterogeneous catalytic ozonation (HCO) has gained attention due to its high oxidation efficiency, strong interference resistance, and low secondary pollution. In this study, a series of trimetallic-carbon composite ozone catalysts were prepared via an organic precursor calcination method using γ-Al2O3 as support. This method enhanced catalytic activity and mechanical strength while overcoming the limitations of carbon materials (low mechanical strength) and metal-based materials (poor mass transfer). The optimized catalyst, CA-FeCoCu, comprising Fe, Co, Cu, carbon, and alumina, exhibited excellent performance in phenol degradation and real industrial wastewater treatment. Characterization revealed that the synergistic effect of trimetals and the introduction of multiple carbon types increased specific surface area and hydroxyl radical (·OH) generation. In a pilot-scale fixed-bed reactor, the CA-FeCoCu/O3 system reduced COD from 120 mg·L−1 to below 40 mg·L−1, with an O3 consumption ratio (O/C) of less than 1, effectively lowering operational costs. This work provides a new strategy for developing efficient and stable heterogeneous O3 catalysts and offers a reference for the practical application of HCO in industrial wastewater treatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3912-0
This erratum corrects an error in the Chinese name of co-first author Tianxiao Xiao (肖天孝) as originally published in the article 'A multi-modal smart chest patch for real-time cardiopulmonary monitoring and anomaly detection' (Sci China Mater, 2025, 68(12): 4413–4422). The corrected Chinese name is 肖天笑. The correction applies solely to the author's name and does not affect the scientific content, experimental data, or conclusions of the original paper. The authors and publisher apologize for any inconvenience caused.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506041
Urban and rural multi-source organic waste faces bottlenecks including high compositional heterogeneity, single resource recovery pathways, and uneven product quality. In the Taihu Lake region, active tourism and catering, high greening, and dense water networks generate large volumes of diverse waste with high moisture content, exacerbating these issues. This study evaluated a coupled bio-drying and aerobic composting process at a demonstration center in Linhu Town, Suzhou, Jiangsu Province, employing a three-stage control strategy: gradient dewatering, high-temperature stabilization, and maturation enhancement. Continuous operation showed that kitchen waste moisture content decreased from 77.70% to 58.69% after 1 day of bio-drying, to 23.22% after 7 days of silo reactor composting, and to 17.70% after at least 20 days of maturation. The aerobic composting phase maintained temperatures above 55°C for over 5 days, reaching a maximum of 68.1°C, meeting the harmless treatment requirements of CJJ 52—2014. After 20 days of maturation, the organic fertilizer product had an electrical conductivity below 4.00 mS·cm−1, organic matter content of 51.22%, total nutrient content of 5.61%, and heavy metal concentrations below the limits of NY/T 525—2021. The results provide technical support for efficient treatment and resource utilization of urban and rural organic waste.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507021
The accumulation of heavy metals in soil around municipal solid waste landfills poses potential risks to human health. This study selected a municipal solid waste landfill and monitored the concentrations of eight heavy metals (Zn, Pb, Cd, Ni, Hg, Cu, As, Cr) in surrounding soil. The geo-accumulation index method was used for pollution assessment, and a health risk assessment model recommended by the USEPA, combined with Monte Carlo uncertainty analysis, was employed to evaluate the pollution status and health risks to nearby residents. Results showed that among the eight metals, Pb, Ni, and Cd exceeded risk screening values at 4.26%, 6.38%, and 4.26% of sampling points, respectively. Geo-accumulation indices indicated overall clean conditions (mean < 0), but slight pollution by Pb, Zn, Ni, Hg, and Cd at some points. Probabilistic risk assessment based on Monte Carlo simulation revealed that for both adults and children, the cumulative non-carcinogenic risk was negligible, while carcinogenic risk was acceptable. However, there was a very low probability (approximately 0.2%) of non-carcinogenic risk for children, and probabilities of unacceptable carcinogenic risk were 0.64% for adults and 3.21% for children. Nickel was the primary contributor to carcinogenic risk, and children faced higher health risks than adults. These findings provide a reference for pollution prevention and health risk management of soil around municipal solid waste landfills.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507032
To mitigate global warming, regional carbon neutrality pathways are critical. Based on the Guangdong Energy Policy Simulator (EPS) model, this study simulates total energy consumption and greenhouse gas (GHG) emissions under baseline, Carbon Neutral 60 (CN60), and Carbon Neutral 50 (CN50) scenarios, and analyzes the emission reduction effects and costs of various energy policies. Results show that by 2060, total energy consumption under CN60 and CN50 decreases by 39% and 44% relative to baseline, respectively. Primary electricity and other energy, natural gas, oil, and coal account for 56%, 26%, 14%, and 4% under CN60, and 60%, 24%, 13%, and 3% under CN50. GHG emissions under CN60 drop to 80×10^6 tCO2e by 2060, an 89% reduction from 2020; under CN50, emissions reach 92 and 55×10^6 tCO2e in 2050 and 2060, respectively, reductions of 87% and 92% from 2020. Policies such as increasing clean electricity share, industrial electrification (hydrogen), increasing green power purchases, building electrification, F-gas reduction, and improving industrial energy efficiency standards show significant reduction effects, with clean electricity share being the primary source. Policies like improving industrial energy efficiency standards, increasing industrial product utilization, and increasing clean energy vehicle market penetration are cost-effective; increasing clean electricity share, green power purchases, building electrification, and F-gas reduction effectively balance reduction effects and costs. Industrial electrification (hydrogen) contributes >5% cumulative reduction but faces economic challenges for full-scale promotion in the short term; industrial carbon capture and storage and electrolytic hydrogen contribute <2% cumulative reduction with high costs. Therefore, Guangdong should prioritize cost-effective policies, promote balanced policies, gradually optimize energy structure, achieve clean electricity, and foster green industrial transformation to achieve carbon neutrality at lower economic cost.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112804
The rapid dissemination of antibiotic resistance genes (ARGs) in aquatic environments poses serious threats to public health and environmental safety under the 'One Health' framework. Nanoplastics (NPs), as co-occurring pollutants, can exacerbate ARG risks by promoting horizontal gene transfer (HGT), yet the influence of different functional groups on extracellular ARG (eARG) transformation remains unclear. This study investigated the effects of carboxy-modified polystyrene NPs (PS-COOH) and amino-functionalized polystyrene NPs (PS-NH2) compared to unmodified polystyrene NPs (PS) on the transformation of the extracellular resistance plasmid IE-V1955 (carrying an ampicillin resistance gene) into Escherichia coli DH5α. Results showed that PS-COOH exposure promoted plasmid transformation similarly to PS, with effects increasing over 0.1–20 mg·L−1. Low concentrations (0.1–0.5 mg·L−1) of PS-NH2 also enhanced transformation, with stronger effects than PS-COOH at equal doses, whereas high concentrations (1–20 mg·L−1) inhibited it. Mechanistically, PS-COOH (0.1–20 mg·L−1) and low PS-NH2 induced intracellular reactive oxygen species (ROS), increased cell membrane permeability, elevated the protein-to-polysaccharide ratio in extracellular polymeric substances (EPS), and promoted biofilm formation, thereby facilitating transformation. High PS-NH2 concentrations caused excessive ROS leading to cell lysis and formed aggregates with plasmids larger than membrane pores, blocking uptake. These findings provide a theoretical basis for assessing the combined environmental health risks of NPs and ARGs.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025121602
This study characterized the body burden of polybrominated diphenyl ethers (PBDEs) in a physical examination population in Shenzhen and evaluated its impact on thyroid function. Serum samples from 368 residents were analyzed for eight PBDE congeners using atmospheric pressure gas chromatography-tandem mass spectrometry (APGC-MS/MS). The median concentration of ∑8PBDEs was 10.2 ng·g⁻¹ lipid weight (lw), ranging from 0.13 to 2089.4 ng·g⁻¹ lw, with BDE-209 predominating (59.7% of total). Multiple linear regression revealed that a 1.7-fold increase in serum BDE-153 was associated with a 0.4% increase in free triiodothyronine (FT3) (P<0.05), while a 1.7-fold increase in BDE-183 was associated with a 0.9% decrease in total triiodothyronine (T3) and a 0.7% decrease in FT3 (P<0.05). Bayesian kernel machine regression (BKMR) indicated a negative correlation between mixed PBDE exposure and thyroid-stimulating hormone (TSH) at high exposure levels. Weighted quantile sum (WQS) regression showed that mixed exposure was associated with decreased T3 levels and T3/FT3 ratio, with BDE-153 and BDE-183 as the primary contributors. These findings suggest that PBDE exposure may adversely affect thyroid function and disrupt thyroid hormone homeostasis, with BDE-183 and BDE-153 playing key roles. This study provides a scientific basis for PBDE health risk assessment and thyroid protection.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025091203
The persistence of tetracycline (TC) in aquatic environments poses significant ecological risks. This study developed a homogeneous reaction system based on carboxylated Fe2+ enhanced peroxymonosulfate (PMS) activation, using citric acid (CA) as a ligand. Carboxylation improved Fe2+ stability and catalytic activity, while solid PMS served as the oxidant, circumventing issues of traditional Fenton processes such as H2O2 instability, complex heterogeneous catalyst preparation, high disposal costs, and toxic metal leaching. The acidic pretreatment enabled by CA inhibited Fe2+ oxidation and promoted sustained PMS activation without external energy input. Under optimized conditions (TC 5 mg·L−1, Fe2+ 0.02 mmol·L−1, CA 0.001 mmol·L−1, PMS 2 mmol·L−1), 88.80% TC degradation was achieved within 60 min. Mechanistic studies revealed that CA protected Fe2+ active sites via carboxyl coordination, facilitating continuous generation of reactive species, including singlet oxygen (1O2) and sulfate radicals (SO4•−). 1O2 was the dominant species (50.5% contribution), followed by SO4•− (35.7%), synergistically driving efficient TC degradation while significantly reducing iron sludge production. Phytotoxicity assays confirmed that treated water exhibited no significant toxicity to wheat seedlings (P > 0.05), indicating effective ecological risk elimination. This work provides a low-energy, operationally simple, and environmentally friendly technology for antibiotic-contaminated water treatment, with promising practical application potential.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024121101
The excessive and uncontrolled use of antibiotics inevitably leads to their release into natural environments, accelerating the production, occurrence, and transport of resistant bacteria and resistance genes. Among these, antibiotic resistance plasmids (ARPs) pose a significant public health challenge due to their environmental persistence and ability to spread and amplify within microbial communities. This study used the tetC gene-pUC18 plasmid as a model ARP to investigate aggregation behavior in aqueous environments under varying pH (3–7), ionic strength (0.001–0.1 mol·L−1 NaCl and 0.001–0.05 mol·L−1 CaCl2), and in the presence of different concentrations of natural colloids. Results indicate that at low pH, ARP structure condenses inward and functional groups may protonate, reducing negative charge and overall size. Compared to Na+, Ca2+ forms cationic bridges between negatively charged phosphate diester groups, significantly enhancing aggregation. Natural colloids induce heteroaggregation with ARPs, with aggregate size increasing with colloid concentration. This study provides scientific evidence for elucidating ARP behavior in soil and groundwater, crucial for assessing risks to human health and ecosystems and understanding global circulation mechanisms.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024122101
Bicarbonate and carbonate ions (HCO3−/CO3^2−) are ubiquitous in wastewater and readily scavenge strong oxidants, leading to the formation of carbonate radicals (CO3·−) in radical-based advanced oxidation processes. This study investigated the influence of HCO3−/CO3^2− on the degradation kinetics of sulfamethazine (SMR) in a UV/TiO2 system. The presence of HCO3−/CO3^2− enhanced the degradation rate of SMR by sixfold compared to UV/TiO2 alone. Radical quenching experiments identified CO3·− as the primary reactive species responsible for the enhanced degradation, with hydroxyl radicals (·OH) also contributing. To quantitatively delineate the roles of reactive species and account for water matrix effects, a kinetic model was constructed using Kintecus software. The model accurately predicted SMR degradation over time and the contributions of individual radicals, demonstrating good predictive capability. Application of the model to real wastewater predicted that CO3·− is the dominant radical responsible for SMR degradation. These findings highlight the critical role of carbonate radicals in UV/TiO2 processes and provide a robust modeling framework for predicting the fate of pharmaceuticals in carbonate-rich waters.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024110202
Anaerobic digestion (AD) is an environmentally friendly biochemical technology for waste treatment and renewable energy production, yet its methane conversion efficiency remains suboptimal. This study employed flux balance analysis (FBA) to determine the optimal temperature for methane production in AD, and subsequently regulated key flexible nodes in the metabolic pathway to maximize methane flux. At the optimal temperature of 40 °C, up-regulating the acetyl-CoA flexible node increased methane flux by 48.5%, while up-regulating the acetate node increased it by 36.6%. The higher improvement via acetyl-CoA regulation is attributed to the fact that 40 °C is unfavorable for hydrogen-producing acetogenic bacteria, making acetyl-CoA the critical control point. These findings demonstrate that flexible node regulation can overcome the limitations of temperature optimization alone. The FBA methodology provides a reliable, cost-effective approach for optimizing target product yields in AD and other fermentation systems, requiring only input and output measurements to resolve intermediate metabolic fluxes.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024120203
Potassium permanganate (KMnO4) oxidation is a promising technology for organic pollutant removal in water due to its low cost and broad pH applicability. However, its moderate oxidation capacity results in slow degradation rates for refractory organic compounds. Carbon materials (CMs), known for their accessibility, stability, and environmental compatibility, have shown great potential in enhancing KMnO4 oxidation. This paper provides a comprehensive review of recent advancements on the enhancement of KMnO4 oxidation of organic pollutants by CMs. The performance and suitability of various CMs in improving KMnO4 oxidation were systematically compared. Additionally, two key mechanisms driving the degradation of organic pollutants in the KMnO4/CMs system were elucidated, along with a discussion on the recycling and regeneration of CMs. Finally, future research directions and development trends for this technology were outlined, aiming to offer insights to advance the practical application of KMnO4/CMs system in water treatment.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024120701
Surface waters contain numerous photoactive substances and low molecular weight carboxylic acids (LCAs). Hydroxyl radicals (HO•) can react with LCAs to generate the highly reducing carbon dioxide anion radical (CO2•−). Excited triplet state dissolved organic matter (3DOM*), a common oxidant in surface waters, may also oxidize LCAs to CO2•−, but this pathway remains unexplored. This study simulated sunlight-driven generation of CO2•− via 3DOM* using 4-benzoylbenzoic acid (CBBP) as a 3DOM* precursor and formate (HCOO−) as a model LCA. Metronidazole (MNZ) served as the target pollutant. Comparative degradation experiments in hν, hν/HCOO−, hν/CBBP, and hν/CBBP/HCOO− systems, combined with electron spin resonance spectroscopy and quenching tests, confirmed that CO2•− generated in the hν/CBBP/HCOO− system was the primary reactive species responsible for enhanced MNZ degradation, originating mainly from 3CBBP* oxidizing HCOO−. Under optimized conditions (8 mmol·L−1 HCOO−, 200 μmol·L−1 CBBP, 10 μmol·L−1 MNZ), 98.2% degradation was achieved within 30 min. Degradation efficiency increased with HCOO− concentration and was pH-independent. Cl−, NO3−, CO3^2−, and low concentrations of HCO3− inhibited degradation, while high HCO3− slightly promoted it. Humic acid (HA) inhibited degradation in a concentration-dependent manner. The system also performed well in real water matrices, suggesting potential for treating micropollutants via reductive pathways.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112102
Based on the 2022 activity data of non-road mobile sources in Hebei Province, this study employed the emission factor method recommended by the Guidelines to estimate emissions of CO, HC, NOx, PM2.5, PM10, and SO2. A comprehensive emission inventory was established, followed by spatial and uncertainty analyses. Scenario analysis, aligned with the 14th Five-Year Plan policies, was used to project emissions for 2030. The results indicate that non-road mobile sources in Hebei emitted 76.1×10^3 t of CO, 20.6×10^3 t of HC, 164.0×10^3 t of NOx, 8.5×10^3 t of PM2.5, 9.0×10^3 t of PM10, and 2.4×10^3 t of SO2. Agricultural machinery was the dominant contributor to CO, HC, PM2.5, and PM10, accounting for over 60.0% of CO emissions. Railway locomotives were the primary source of NOx, contributing 50.9%. For SO2, agricultural machinery and railway locomotives contributed 39.0% and 44.4%, respectively. The highest emitting cities were Tangshan (21.3%), Shijiazhuang (15.7%), Cangzhou (11.6%), and Handan (11.6%). Ship emissions were concentrated in Tangshan Port; civil aviation emissions were mainly in Shijiazhuang, Tangshan, Qinhuangdao, and Handan; railway emissions were distributed in Shijiazhuang, Baoding, and Handan. Under the updated emission standard scenario, NOx and PM10 emissions in 2030 could be reduced by approximately 35.0%. The phase-out of old machinery yielded the largest reduction in CO (36.0%), while both electrification and phase-out scenarios significantly impacted HC emissions.
Environmental Chemistry•2026•DOI: 10.0000/202604-1
An analytical method was developed for the simultaneous determination of 11 organic ultraviolet absorbents (OUVs) in coral tissues using ultra-high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS). Target analytes included benzophenones (BP, BP-2, BP-3, BP-8) and other common UV filters. Sample pretreatment and chromatographic conditions were systematically optimized. Coral tissue samples were extracted by combined vortexing and ultrasonication, separated on a CAPCELL PAK MG C18 column using a mobile phase of methanol-0.1% formic acid aqueous solution under gradient elution, and determined by multiple reaction monitoring (MRM) with internal standard quantification. Method validation demonstrated good linearity for all target compounds over the range of 0.1–500 μg·L−1 (R2 > 0.990), with method detection limits ranging from 0.020 to 0.133 ng·g−1. The mean recoveries at low, medium, and high spiking levels ranged from 60.5% to 120.3%, with relative standard deviations (RSDs) of 1.6%–10.7%. The method offers advantages of simple pretreatment, good repeatability, and high accuracy, making it suitable for high-throughput determination of OUVs in complex biological matrices such as corals. The method was applied to analyze 89 coral samples collected from Xidao Island, Sanya, and five target OUVs were detected in the samples. This method provides reliable technical support for elucidating the accumulation characteristics of OUVs in corals and assessing their potential ecological risks.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604001
This study systematically investigated the occurrence, spatial distribution, sources, and ecological risks of 160 pesticides in Dianchi Lake, a typical plateau lake impacted by agricultural activities. A total of 37 pesticides were detected in the water, with total concentrations ranging from 64.2 to 1132.8 ng/L (average 610.0 ng/L). Fungicides, including boscalid (BOS), fluopicolide (FPC), and dimethomorph (DMM), were dominant, contributing up to 65.0% of the total concentration. Spatially, the southern lake region exhibited significantly higher concentrations (672.5 ng/L) than the north, attributed to intensive facility agriculture. Highly hydrophobic pesticides, such as penconazole (PEN), showed a tendency to enrich in bottom layers. Source apportionment identified inflowing rivers and wastewater treatment plant effluents as primary input sources, with average concentrations 7 and 9 times higher than lake water, respectively. Ecological risk assessment revealed that pesticides posed the highest risk to algae, followed by daphnia and fish. Prometryn (PMT) was identified as a high-risk factor for algae, while profenofos (PFF) and carbendazim (CBD) posed potential threats to higher trophic levels. These findings provide fundamental data and technical support for understanding pesticide pollution in plateau lake ecosystems.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604011
Reverse osmosis (RO) membrane fouling remains a critical bottleneck in reclaimed water production, yet its spatial heterogeneity over extended operation is poorly understood. This study investigated fouling characteristics and microbial community dynamics on RO membranes after 3.5 years of operation in a full-scale microfiltration-reverse osmosis (MF-RO) system treating reclaimed water. Long-term monitoring showed stable effluent quality (turbidity <0.1 NTU, conductivity <400 μS/cm), but RO inlet pressure exhibited seasonal fluctuations of 15%–22% between summer and winter, attributed to water viscosity changes. Membrane autopsies revealed distinct fouling layers at the inlet (RO1) and outlet (RO2) ends. RO1 featured a dense bio-inorganic composite fouling layer with CaSO4 crystals and rod-shaped microbial aggregates (5–10 μm), dominated by Proteobacteria (77.11%), particularly Alphaproteobacteria (71.49%) and Xanthobacteraceae (35.29%), which secreted extracellular polymeric substances (EPS) to form biofilms. In contrast, RO2, exposed to higher salinity, showed reduced microbial abundance (Proteobacteria decreased to 64.79%) and a shift toward halotolerant taxa, including Microbacteriaceae (23.73%) and Actinobacteriota (24.76%), with EPS secretion increased by 42%. Alphaproteobacteria relative abundance dropped by 19.3%, while Gammaproteobacteria rose to 12.54%. These findings elucidate salinity-driven microbial succession and spatial heterogeneity of fouling, providing a basis for targeted antifouling strategies and 'zonal-graded' cleaning protocols in reclaimed water plants.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604019
A two-stage electrostatic precipitator (ESP) integrating a sawtooth-rod electrode precharging unit and a plate-plate collection unit was developed for simultaneous removal of fine particles and volatile organic compounds (VOCs) from catering fumes. Using KCl particles and toluene as surrogates, the system achieved a fine particle (<0.3 µm) collection efficiency of 91% and a total particle collection efficiency exceeding 98% at applied voltages of +12 kV (sawtooth-rod) and -8.5 kV (plate-plate), with an ozone concentration of 176.9 mg/m³. The presence of particles enhanced toluene degradation, increasing removal efficiency from 29.2% to 53.1%. Positive DC discharge on the sawtooth-rod electrode yielded a higher corona current (800 µA vs. 375 µA for negative) and lower ozone generation (101.4 mg/m³ vs. 176.9 mg/m³), indicating superior suitability for catering fume treatment. The stable discharge characteristics of the sawtooth-rod electrode reduce energy consumption and extend operational cycles, offering a promising technical pathway for efficient, compact, and intelligent ESP systems in catering fume purification.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225184
Thermal power units have long dominated China's energy structure due to the low cost of coal and their role in ensuring grid stability. However, under the dual pressures of climate change and national carbon peaking/neutrality goals, the environmental impact of their 'three wastes' has become critical, necessitating energy-saving retrofits. This review systematically examines mainstream energy-saving technologies for thermal power units, including boiler combustion optimization, heating surface cleaning, turbine flow path upgrades, waste heat recovery and cascade utilization, and cold-end system optimization. Using coal consumption rate as the core economic index, the study integrates case studies and operational data from typical domestic and international units to evaluate the latest progress, practical effects, advantages, and limitations of each technology. Results indicate that these technologies significantly improve energy efficiency and reduce pollution. For instance, boiler combustion optimization based on support vector machines and neural networks enhances thermal efficiency and reduces NOx emissions. Turbine flow path modifications, from full three-dimensional CFD optimization to advanced blades and combined steam seals, yield notable gains in cylinder efficiency and heat rate reduction. Low-temperature economizers reduce coal consumption and auxiliary power/water use in dust removal and desulfurization systems. Heat pump applications include absorption, compression, and hybrid types. In cold-end optimization, data-driven predictive maintenance and real-time performance tuning of condensers achieve nearly 50% energy savings in circulating water pumps and an average coal consumption reduction of 2-3 g/(kW·h). Despite these advances, gaps remain in multi-objective optimization robustness, intelligent diagnosis, and advanced materials. Future research should focus on deep reinforcement learning for adaptive control, sensor networks for real-time diagnostics and predictive maintenance, and high-temperature corrosion-resistant materials for heat exchangers, while balancing initial investment and maintenance costs.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225200
Phosphogypsum, a by-product of wet-process phosphoric acid production, poses severe environmental and safety challenges due to its massive annual output and stockpiling. This study addresses the urgent need for resource utilization by employing phosphogypsum as the primary raw material, supplemented with ground granulated blast furnace slag, fly ash, and type II anhydrite. Two foaming agents, sodium bicarbonate (NaHCO3) and aluminum powder, were used to regulate pore structure, and their effects on ceramsite performance were compared. Under identical preparation conditions, aluminum powder yielded higher 7-day cylinder compressive strength than NaHCO3. Optimal formulations achieved a maximum cylinder compressive strength of 6.5 MPa with a bulk density of 1020 kg/m3, meeting lightweight aggregate concrete strength requirements. Aluminum powder produced closed pores, reducing bulk density to as low as 765 kg/m3, while NaHCO3 generated interconnected pores leading to higher water absorption. XRD, SEM, and BET analyses revealed that strength-contributing phases are calcium silicate hydrate and calcium aluminate hydrate; trace heavy metals (Mo, Ti) hinder their formation, causing structural defects. This work demonstrates a green, non-fired route for phosphogypsum valorization, offering environmental and economic benefits and a pathway for large-scale utilization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3451-2
Visual aesthetics is a key metric of semi-transparent organic photovoltaics (ST-OPVs) for building-integrated solar windows, yet previous studies have primarily focused on the compromise between efficiency and transparency. This work addresses the overlooked aspect of full visual aesthetic control, particularly the bidirectional reflected color for architectural harmony, via designing ST-OPVs with double-sided ultra-thin Ag/TeO2 transparent electrodes. This design facilitates full-spectrum color tunability covering the whole standard color gamut of CIE coordinates on both surfaces, achieved simply by adjusting layer thicknesses. The resulting devices exhibit neutral transparency (16.6%–27.0% average visible transmittance) and competitive power conversion efficiencies (8.1%–9.2%). Additionally, the devices demonstrate strong flexibility, with flexibility-adaptive coloration and curvature-enhanced aesthetics. This work presents an ST-OPV design featuring full visual aesthetics and considerable performance, paving the way for commercialization of organic solar windows for building and vehicle integration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3487-x
Continuous carbon fiber-reinforced ZrB2-SiC ceramic matrix composites are promising thermal protection materials for hypersonic vehicles and reusable spacecraft. Although injection-assisted vacuum impregnation (IVI) offers advantages such as shorter processing cycles, lower costs, and reduced fiber damage compared to conventional methods, phenolic/acetone-based IVI systems yield composites (designated as CPS) with limited ceramic contents. To address this, an aqueous slurry-based IVI approach was developed, producing composites designated as CHS. After a single IVI cycle, CHS achieved a ZrB2 phase volume fraction of 25 vol.%, 47% higher than CPS, while reducing processing time by 49%. After chemical vapor infiltration, CVI-CHS composite exhibited a room-temperature compressive strength of 106.78±10.53 MPa, representing a 28% improvement over CVI-CPS. Crack propagation analysis revealed discontinuous zigzag patterns under compression, dominated by fiber bridging and pull-out energy dissipation mechanisms. Flexural results revealed both composites retain considerable strength (111.15±12.46 and 83.15±12.03 MPa) along with low flexural modulus (13.00±2.41 and 13.52±6.99 GPa) and high strain tolerance (1.32%±0.018% and 1.07%±0.34%). It is attributed to the anisotropy of fiber preforms and the elastic modulus mismatch among different phases, which hindered effective constraint of fibers by the matrix and, in turn, facilitated mitigation of stress concentration. Additionally, CVI-CPS demonstrated superior X-band electromagnetic interference (EMI) shielding (34–36 dB) compared to CVI-CHS (22–27 dB), resulting from synergistic effects between pyrolitic and deposited carbon in the matrix of the former. Both composites showed enhanced EMI shielding efficiency with increasing temperature up to 600°C. This eco-friendly aqueous IVI strategy enables high-performance, cost-effective thermal protection materials with higher ceramic loading and tunable multifunctional properties.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3782-0
Oral mucositis (OM) is a debilitating complication of cancer therapy, characterized by severe pain, mucosal barrier breakdown, and infection risk. Current hydrogel-based topical systems suffer from poor transmucosal permeation and lack of inflammatory microenvironment-triggered drug release. Here, we report a supramolecular strategy for designing guanosine-fibril hydrogels and derived microneedle patches. Tavaborole (Ta), crisaborole (Cr), and strontium (Sr2+) ions serve dual roles as structural building blocks and biofunctional agents. Unlike conventional G4·K+ fibrils, the unique G4·Sr2+-Ta/Cr fibrils incorporate Ta/Cr via boronic ester bonds on guanosine and Sr2+ through G-quartet cation recognition. This design mechanically reinforces the hydrogel through additional hydrophobic interactions and ion-pair recognition, while synergistically providing antimicrobial/anti-inflammatory effects (Ta/Cr), pro-angiogenic activity (Sr2+), and reactive oxygen species (ROS) scavenging (guanosine). The optimized gelation process enables fabrication of microneedle patches with pseudomembrane-penetrating capability and ROS-triggered drug release via boronic ester hydrolysis. In vivo mouse experiments confirm efficacy in controlling OM-associated inflammation, modulating oral microbiota homeostasis, and promoting angiogenesis at ulcer sites. This work demonstrates multifunctional integration via hierarchical structural design, extending guanosine supramolecular assemblies into bioactive platforms for OM treatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3545-7
Magnetically driven hydrogel robots show promise in biomedical and underwater applications due to remote controllability, flexibility, biocompatibility, and chemical stability. However, limited functional integration restricts their adaptability. Here, a universal modular assembly strategy is introduced using a self-healing κ-carrageenan/polyacrylamide hydrogel embedded with magnetic particles, enabling free assembly of magnetic actuation modules. These modules construct soft robots with complex geometries and magnetization distributions, allowing diverse deformations under magnetic fields. The strategy further integrates photocatalysis by embedding Ru-Bi2CrO6 photocatalysts into functional modules, yielding an oxygen-generating robot. This robot exhibits flexible underwater movement via magnetically controlled oscillatory actuation, minimizing water agitation while supplying stable oxygen to specific aquatic environments. The photocatalytic oxygen evolution rate reaches 389.1 μmol g−1 h−1. The hydrogel skeleton suppresses particle aggregation and sedimentation, and facilitates magnetic recovery. This scalable and adaptable approach advances multifunctional soft robot design.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61100-6
Sodium-ion capacitors (SICs) are attractive for low-cost and safe energy storage, but their practical development is limited by sluggish Na+ storage kinetics and structural instability of anodes. Control of both bulk structure and surface chemistry can address these limitations. We report a heteroatom-rich porous carbon (HRPC) derived from spores via hydrothermal pretreatment, low-temperature carbonization, and acid-mediated functionalization. The optimized GLSHC-HNO3 anode exhibits hierarchical porosity and multi-element co-doping, enabling rapid ion/electron transport, improved electrolyte wettability, and abundant Na+ adsorption sites. Density functional theory calculations reveal distinct contributions of different heteroatom configurations to sodium adsorption. The HRPC anode delivers an ultrahigh reversible capacity of 446.1 mAh g−1 at 50 mA g−1, retains 237.3 mAh g−1 at 2 A g−1, and shows excellent cycling stability. A full SIC with a polyaniline-derived porous carbon cathode achieves an energy density of 114.4 Wh kg−1 at 290 W kg−1, 43.1 Wh kg−1 at 1450 W kg−1, and a maximum power density of 5800 W kg−1, with 84.3% capacity retention after 5000 cycles and nearly 100% Coulombic efficiency. This work establishes a scalable, sustainable route for converting biomass into high-value carbon anodes, providing a new pathway for high-performance sodium-ion energy storage.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61102-X
Silicon-carbon composites prepared by chemical vapor deposition (CVD) are promising anode materials for high-energy-density lithium-ion batteries. However, the influence of the pore structure of the porous carbon (PC) carrier on silicon deposition behavior, and the impact of surface silicon on cycling stability, remain unclear. This study systematically investigates these effects using nitrogen adsorption-desorption analysis, X-ray photoelectron spectroscopy, and thermogravimetric analysis. Porous carbons with varying pore architectures were synthesized by adjusting KOH activator ratios. Results show that increased micropore volume facilitates higher silicon mass loading, but also elevates the content of surface floating silicon due to greater silane exposure. Moderately increasing mesopores in high-microporosity carbon promotes deeper silicon deposition, reducing surface floating silicon. Excessive surface floating silicon hinders lithium-ion diffusion kinetics, leading to accumulation of active lithium, accelerated SEI growth, and electrode degradation. Electrochemical testing reveals that the optimized silicon-carbon composite maintains a high specific capacity of 693.1 mAh/g after 150 cycles at 0.5 C (900 mA/g). This work provides new insights into the development and failure mechanisms of CVD-derived silicon-carbon composite anodes, emphasizing the critical role of pore structure in mitigating surface silicon and enhancing cycling stability.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508053
Polycyclic aromatic hydrocarbons (PAHs) in industrial soils pose significant risks due to their hydrophobicity and low bioavailability, limiting the efficacy of bioremediation. This study investigated the enhancement of an in-situ electrokinetic-biological barrier (EK-BB) system for PAH-contaminated soil using biosurfactants. Three biosurfactants—rhamnolipid (RL), alkyl polyglycoside (APG), and saponin (SAP)—were applied individually and in combinations at 10× critical micelle concentration (CMC), and the optimal RL+APG mixture was further tested at 2.5, 5.0, 7.5, and 10× CMC. Results showed that biosurfactant application improved soil electrical current, moisture retention, and PAH removal. Combined surfactants outperformed single ones, with the 10× CMC RL+APG treatment (Exp IV) achieving the highest average current intensity and moisture content, 1.31 and 1.12 times that of the control (CK), respectively, and a PAH removal of 106.02 mg·kg⁻¹. Biosurfactants also promoted bacterial growth in both contaminated soil and the biobarrier layer; the 10× CMC RL+APG treatment increased bacterial counts by 6.24-fold and 44.8%, respectively. However, excessive surfactant concentrations led to PAH accumulation in the biobarrier and clean soil. The 5× CMC RL+APG treatment provided optimal balance, maximizing PAH removal while maintaining barrier effectiveness. These findings confirm that appropriate biosurfactant concentrations can enhance EK-BB remediation, offering technical support for PAH-contaminated site remediation and safe reuse.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507094
To address land waste and poor bearing capacity from sludge landfill, this study developed a composite solidifying agent using loess, fly ash, desulfurized gypsum, and cement. Orthogonal experiments combined strength testing, SEM/XRD microanalysis, permeability and heavy metal leaching tests, and cost accounting. Results show that cement significantly enhances early and mid-term strength, while loess dominates later strength development. Optimal fly ash and desulfurized gypsum content is 12% each. The optimal mix ratio (loess:fly ash:desulfurized gypsum:cement:sludge) is 0.1:0.12:0.12:0.08:1. The solidified matrix forms dense structures via C-S-H gel and ettringite (Aft), effectively controlling heavy metal leaching at low cost. This work enables solid waste resource utilization and provides robust support for sludge solidification engineering.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508047
Selective recovery of aluminum compounds from fly ash is a key route for its high-value utilization. This study developed a multi-stage activation process for extracting Al(OH)3 from fly ash, comprising mechanical activation, calcination activation, chemical separation, and carbonation precipitation. Fly ash was mixed with carbide slag and CaF2, then calcined; the resulting clinker was leached with Na2CO3 solution to extract Al. The CaO generated from high-temperature calcination of carbide slag facilitated the separation of Si and Al. After solid-liquid separation, CO2 was introduced into the Al-rich leachate to precipitate Al(OH)3. The process promoted the formation of Ca12Al14O32F2 and inert Ca2SiO4, achieving efficient Si-Al separation during calcination. Under optimal conditions (mechanical activation for 60 min, 4% CaF2, calcination at 1000°C for 2 h, leaching with 40 g/L Na2CO3), the Al extraction rate reached 91.8%, and the product purity was 98.9%. The alumina extraction residue exhibited porous and highly reactive characteristics, suitable for producing flame-retardant materials or high-value silicon-based products (e.g., white carbon black, molecular sieve adsorbents). The process offers a promising industrial route for fly ash valorization, with potential integration with cement production lines for synergistic CO2 capture and utilization.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60629-3
This study reports the synthesis of a novel Z-scheme heterojunction composite film comprising Ag/Bi2MoO6/BiOBr via electrochemical processes, ion-exchange techniques, and subsequent photodeposition of silver nanoparticles. The incorporation of Ag nanoparticles exploits localized surface plasmon resonance (LSPR) effects and serves as an electron mediator, establishing a Schottky barrier that suppresses charge recombination. The optimized 1.5% Ag/Bi2MoO6/BiOBr film achieves a CO production rate of 13.65 μmol/(g·h) from photocatalytic CO2 reduction, significantly outperforming the unmodified Bi2MoO6/BiOBr film. Photocurrent and impedance analyses confirm enhanced charge separation in the Ag-modified composite. A non-linear relationship between Ag loading and photocatalytic efficiency was observed, with optimal performance at 1.5% Ag. The proposed Z-scheme mechanism elucidates the synergistic interactions among components, providing a scientific basis for rational design of advanced photocatalysts and immobilized systems for CO2 reduction. This work offers insights into the development of efficient, sustainable photocatalytic technologies for carbon capture and utilization.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012501
Dibutyl phthalate (DBP) is a ubiquitous environmental pollutant posing potential risks to aquatic ecosystems. This study assessed the developmental toxicity of DBP in Japanese medaka (Oryzias latipes) embryos. Embryos were exposed to gradient DBP concentrations (1, 5, 50, 500 μg·L−1, and 5 mg·L−1) for 15 days. Endpoints included embryonic heart rate, hatching time, survival rate, larval swimming behavior, and expression of genes related to cardiovascular, nervous, thyroid, antioxidant systems, and estrogenic effects. Results showed that 5 mg·L−1 DBP significantly reduced embryonic heart rate (P < 0.0001), leading to hatching failure and mortality. Exposure to 500 μg·L−1 DBP significantly reduced hatching rate (P < 0.01) and survival rate (P < 0.0001). DBP exposure caused developmental delay, cardiovascular hemorrhage, spinal curvature, yolk sac edema, and inhibited larval swimming behavior. At the molecular level, DBP significantly altered expression of atrap, dkk1, bnpa, fx, and dvl mRNA, affecting cardiovascular development; downregulated trha, mbp, and elavl3 mRNA, indicating endocrine disruption and neurotoxicity; upregulated cat, gpx2, and gsta mRNA, inducing oxidative stress; and upregulated vtg1, erβ1, and chgl mRNA, demonstrating estrogenic effects. This study demonstrates that DBP exposure adversely affects growth, development, hatching, survival, swimming behavior, and gene expression in Japanese medaka embryos, highlighting ecological risks of DBP pollution in aquatic environments.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010201
The Guanzhong region, traversed by the Wei River Basin, is one of the most industrially, agriculturally, and medically advanced and densely populated areas in Northwest China, has seen increasing attention paid to the pollution of perfluoroalkyl substances (PFASs) in its surface water environment. This study systematically investigated the pollution characteristics of PFASs in the surface water of this region and their ecological and health risks. By optimizing the online solid-phase extraction-liquid chromatography-tandem quadrupole mass spectrometry (Online SPE-LC/MS/MS), efficient detection of 19 PFASs was achieved, with the method detection limits ranging from 0.2 ng·L−1 to 0.3 ng·L−1, linear correlation coefficients all ≥ 0.990, and spiked recoveries between 75.2% and 130.0%. Monitoring data indicated that PFBA, PFPeA, PFHxA and PFOS, short-chain perfluorinated compounds, were the main pollutants in this region, with high detection frequencies and concentrations, but the overall content was lower than that in most areas of China. The concentrations of PFASs in surface water showed significant seasonal variations, with the highest concentrations during the dry season (∑19PFASs:126.1 — 2584.3 ng·L−1), followed by the normal season (∑19PFASs:3.5—3567.6 ng·L−1), and the lowest during the wet season (∑19PFASs:26.3—294.6 ng·L−1). Ecological risk assessment showed that, except for PFDoDA in the dry season, the ecological risk quotient (RQ) of all other PFASs was < 1. Although the water of the Wei River is not used as direct drinking water, health risk assessment indicated that all PFASs posed low risks, with only PFOA and PFOS showing potential risks (HR > 0.1) to adults and children at some sites during dry/normal seasons. This study provides a scientific basis for PFASs pollution control in the Wei River Basin.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025092802
Activated carbon (AC) filters in drinking water treatment plants (DWTPs) experience significant adsorption performance decline over extended operation, yet complete media replacement is a major cost. To evaluate cost-effective strategies, pilot-scale column experiments with five AC replacement ratios (0%, 30%, 50%, 70%, and 100%) were conducted to assess removal of disinfection by-product (DBP) precursors and pesticide-related emerging contaminants. For dissolved organic matter (DOM), all fractions except low molecular weight compounds (LMWC) achieved >85% of the removal obtained with full replacement when 70% new AC was used, with UV254 removal reaching 70%. LMWC, due to small molecular size and low adsorption energy, required higher replacement ratios or full replacement for substantial removal. For DBPs, removal of trihalomethanes (THMs) and haloacetic acids (HAAs) was insensitive to replacement ratio, while haloacetaldehydes (HALs) removal improved markedly with increasing ratio, indicating structural selectivity. For pesticide-related contaminants, all except triazoles achieved >95% removal at 70% replacement; triazoles, due to high water solubility, high polarity, and low octanol-water partition coefficient, achieved only ~60% removal. Overall, replacing 70% of AC restored treatment performance to >80% of that with full replacement, ensuring effluent quality while saving ~30% of new carbon cost. Molecular structure, polarity, and pore size matching are key determinants of removal efficiency; optimizing replacement ratio balances water quality and economic benefits.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010803
Global aquaculture is expanding rapidly, with China leading in production and being the only country where aquaculture output exceeds wild catch. This growth raises concerns about environmental contamination, particularly mercury (Hg), and the safety of aquaculture products. This study investigated Hg accumulation and trophic transfer in a typical ecological mariculture area in Tangshan, Hebei Province, by measuring species-specific Hg concentrations in sediments and various aquatic organisms. Sediment total mercury (THg) levels were extremely low, averaging 4.0 ± 1.3 ng·g−1 dry weight (n=56), attributed to sandy/silty sediments with low adsorption capacity and minimal external/internal Hg inputs. In aquaculture fish, muscle THg and methylmercury (MeHg) concentrations were 59.7 ± 30.0 and 53.8 ± 29.2 ng·g−1 wet weight (n=7), respectively, comparable to wild fish from the same area. This is due to efficient trophic transfer and biomagnification of Hg, especially MeHg, along the food chain, influenced by food chain structure, primary consumer accumulation, and metabolic rates. At three seafood consumption levels (41.6–255.6 g·d−1), estimated daily intakes (EDI) of MeHg for Chinese adults ranged from 0.01 to 0.40 μg·kg−1·d−1, with target hazard quotients (THQ) from 0.13 to 3.98. Except for Penaeus monodon and Metapenaeus ensis, all other aquaculture products at high consumption levels exceeded the USEPA safety threshold for MeHg EDI and had THQ > 1, indicating potential health risks.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012101
Continuous monitoring of 114 volatile organic compounds (VOCs) was conducted in the urban atmosphere of Haigang District, Qinhuangdao City, from September 2022 to February 2023. The volume concentrations of total VOCs were 42.72×10⁻⁹ in autumn and 25.15×10⁻⁹ in winter. The predominant species were isopentane, ethane, and ethylene. Ozone formation potential (OFP) analysis indicated that alkanes and alkenes dominated the atmospheric pollution during autumn and winter, with isopentane and ethylene being the largest contributors. Aromatic hydrocarbons contributed up to 85.00% of the secondary organic aerosol formation potential (SOAFP), with benzene as the primary species. Positive matrix factorization (PMF) identified four major sources: technological processes and oil/gas volatilization (35.57%), combustion and petrochemical emissions, motor vehicle emissions, and regional background sources. The results underscore the need for targeted control of VOCs from industrial and vehicular sources to mitigate secondary pollution in coastal cities.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025083003
To obtain freshwater from saline water and seawater, a double-layer evaporator consisting of carbon spheres and corn stalks was fabricated (abbreviated as CC). Corn stalks served as the evaporator substrate, and a mixed hydrogel of carbon spheres and polyvinyl alcohol functioned as the photothermal conversion layer. The solar-driven interfacial evaporation and desalination performance of the CC evaporator was investigated. The glucose-derived carbon spheres exhibited a uniform morphology and achieved 95% light absorption across 200–2500 nm. Under 1 sun (1 kW·m−2) irradiation, the CC with 3 cm height (CC-3) reached an exceptional evaporation rate of 3.55 kg·m−2·h−1 with a remarkable energy efficiency of 97.53%. When different wind speeds (1.5, 2, and 2.5 m·s−1) were applied, the evaporation rates further increased to 7.17, 8.92, and 10.41 kg·m−2·h−1, respectively. The evaporation rate of CC-3 for 3.5% saline was 3.46 kg·m−2·h−1. A 5-day long-time experiment exhibited stable desalination and excellent salt tolerance. Under a wind speed of 2.5 m·s−1, the evaporation rate reached 9.56 kg·m−2·h−1. In an outdoor natural light within a closed system and 2.5 m·s−1 of wind speed, the maximum evaporation rate and cumulative evaporation amount for seawater were 9.59 kg·m−2·h−1 and 66.0 kg·m−2, with no salt crystallization observed on the CC surface. These results demonstrate the potential practical application of the CC evaporator in seawater desalination.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025111302
High-concentration chloride ions (Cl−) in industrial wastewater cause severe corrosion and environmental hazards. Conventional removal methods suffer from low efficiency, high cost, and difficulty in product recovery. This study fabricated porous metallic bismuth-based blocks (Bi-PM) via 3D printing, combining chemical precipitation with additive manufacturing. Systematic evaluation of Cl− removal under varying pH and light irradiation revealed that at pH 0.1 and 0.5, dark-condition efficiencies were 53.6% and 31.0%, respectively, increasing to 69.3% and 38.1% under light. Radical trapping identified photogenerated holes as the primary active species, oxidizing metallic Bi to release Bi3+ and enhance precipitation. At pH 0.5, Bi-PM exhibited balanced efficiency and structural stability; over five cycles, average removal efficiency was 25% in darkness versus 41.2% under light, with superior stability under illumination. XRD and SEM confirmed abundant BiOCl formation on the surface under light, mitigating Bi loss. This approach ensures high chloride removal while minimizing material degradation, offering a novel pathway for industrial wastewater treatment.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605002
The single-phase partial nitrification and anammox (SPN/A) process has seen limited widespread application due to its slow startup and difficulties in enriching anaerobic ammonium-oxidizing bacteria (AnAOB). This study utilized high-ammonia nitrogen wastewater to initiate and enhance the SPN/A process in a pilot-scale integrated fixed-film activated sludge (IFAS) reactor. By establishing an IFAS-SPN/A coupled system based on the symbiotic relationship between biofilm and sludge, rapid startup and efficient AnAOB enrichment were achieved. An innovative sludge inoculation strategy was employed: first, conventional nitrifying sludge was inoculated to initiate shortcut nitrification and allow ammonia-oxidizing bacteria (AOB) to colonize blank carriers; subsequently, anammox sludge was inoculated to promote efficient AnAOB enrichment on the AOB biofilm. The influent was low-temperature shift condensation water from a synthetic ammonia workshop, with an average ammonium nitrogen concentration of 2300 mg/L and COD ranging from 50 to 200 mg/L. The 180-day experiment comprised three stages: shortcut nitrification startup, SPN/A startup, and load intensification. The system successfully started up SPN/A within 120 days, achieving total nitrogen removal efficiency and removal load of (90.21±2.18)% and (0.31±0.07) kg/(m³·d), respectively, through synergistic biofilm and suspended microorganisms. During load intensification, AnAOB relative abundances in biofilm and flocs reached 18.8% and 35.3%, respectively, and removal load increased to (0.64±0.11) kg/(m³·d). Stable influent quality is a prerequisite for efficient and stable nitrogen removal; a surge in influent ammonium concentration caused nitrite accumulation imbalance and deteriorated performance. Adding an equalization tank before the aeration tank mitigates water quality fluctuations, and a 'dilution-reconstruction' strategy for low-ammonia wastewater facilitates rapid recovery after performance deterioration.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605011
Phytoplankton are highly sensitive to environmental changes and respond rapidly, making their community dynamics crucial early warning indicators of lake ecosystem health. Previous studies have qualitatively analyzed the combined effects of multiple physicochemical water quality factors on phytoplankton communities, but few have quantitatively distinguished direct from indirect effects. This study employed correlation analysis, redundancy analysis, and structural equation modeling to investigate the spatiotemporal distribution of phytoplankton communities in Baiyangdian Lake and their driving factors. A total of 113 species belonging to 57 genera and 7 phyla were recorded. Phytoplankton density exhibited significant seasonal and spatial variability, peaking in summer. Diatoms and green algae dominated in spring, transitioning to cyanobacterial dominance in summer and autumn, and reverting to green algae in winter. Structural equation modeling revealed that water temperature had a total positive effect on phytoplankton biomass (β = 0.96), comprising a direct positive effect (β = 0.94, P < 0.05) and an indirect positive effect via increased abundance (β = 0.02). Total nitrogen (TN) had a negative total effect on biomass (β = -0.98), with a direct negative effect (β = -0.97, P < 0.05) and an indirect negative effect via reduced abundance (β = -0.01). TN also negatively affected abundance (β = -0.15, P < 0.05). These findings provide a scientific basis for ecosystem health assessment, eutrophication control, and biodiversity protection in Baiyangdian Lake.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605013
The escalating eutrophication of aquatic systems has intensified algal blooms, leading to substantial release and accumulation of algal-derived dissolved organic matter (ADOM), which profoundly influences carbon cycling and pollutant transport. Iron minerals, particularly ferrihydrite, are recognized as critical mediators of DOM sequestration, yet the adsorption fractionation of ADOM under varying environmental conditions remains poorly understood. This study systematically investigated the effects of pH (2.0–10.0) and initial dissolved organic carbon (DOC) concentration (2–100 mg C/L) on the adsorption capacity and selectivity of ADOM onto ferrihydrite, employing UV-Vis spectroscopy and excitation-emission matrix fluorescence with parallel factor analysis (EEM-PARAFAC). Results demonstrated that adsorption capacity increased with pH from 2.0 to 7.0, reaching a maximum of 21.59 mg C/g at pH 7.0, followed by a decline at pH > 7.0 due to enhanced electrostatic repulsion. Within the environmentally relevant pH range of 3.0–9.0, selective fractionation intensified with increasing pH, favoring highly aromatic, high-molecular-weight chromophoric DOM (CDOM) and protein-like/aromatic amino acid fluorescent DOM (FDOM) with high humification and autochthonous characteristics. With increasing initial DOC concentration, adsorption exhibited non-linear growth, with preferential uptake of low-aromaticity, high-molecular-weight CDOM and protein-like FDOM of lower humification and stronger autochthonous features. These findings elucidate that ferrihydrite can effectively sequester reactive ADOM components via pH- and concentration-dependent selective adsorption, potentially altering DOM composition and reactivity in eutrophic waters, thereby providing fundamental data for understanding iron mineral-mediated internal carbon sequestration.