SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4279-0
Inkjet printing has emerged as a viable additive manufacturing route for organic light-emitting diodes (OLEDs), offering drop-on-demand patterning, high material utilization, and compatibility with large-area flexible substrates. This review critically examines the formulation science, printhead physics, and drying kinetics that govern the quality of inkjet-printed organic layers. We analyze the rheological window required for stable jetting, typically 1–20 mPa·s viscosity and 25–45 mN/m surface tension, and the dimensionless Ohnesorge number (0.1 < Z < 1) that defines satellite-free droplet formation. The coffee-ring effect, driven by capillary flow and solvent evaporation gradients, remains the dominant failure mode for pixel non-uniformity; binary solvent systems and substrate temperature control (40–60 °C) mitigate this. We survey recent progress in printed hole-transport, emissive, and electron-transport layers, with particular attention to cross-linkable hole-transport materials that resist interlayer dissolution. Device performance metrics from printed OLEDs now reach external quantum efficiencies of 15–20% for fluorescent emitters and >25% for phosphorescent systems, with operating lifetimes (T95) exceeding 1,000 hours at 1,000 cd/m². We identify remaining bottlenecks: nozzle clogging from aggregated nanoparticles, film thickness variation across large panels, and the absence of standardized ink formulations. The review concludes with a roadmap for industrial adoption, emphasizing in-line metrology and closed-loop process control as prerequisites for yield parity with vacuum-deposited OLEDs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4343-7
Piezoelectric materials interconvert mechanical and electrical energy, but piezoceramics are brittle while PVDF-based ferroelectric polymers exhibit low piezoelectric coefficients (d33 ≈ -30 pC N-1). Chemical modification via morphotropic phase boundary (MPB) engineering has raised d33 in P(VDF-TrFE) to -63.5 pC N-1, and to -69 pC N-1 with stretching, but intrinsic piezoelectricity in relaxor terpolymers remains limited. Here, relaxor ferroelectric P(VDF-TrFE-CFE) with varying C=C double bond (DB) content is synthesized via dehydrochlorination. Structural and electrical characterization reveals that increasing DB content stabilizes long-range ferroelectric order while suppressing short-range relaxor characteristics, forming a trans/helix phase boundary. At a critical DB content of 2.0 mol%, a markedly enhanced intrinsic d33 of -129.0 pC N-1 is achieved, outperforming previous MPB approaches. This finding addresses the fundamental bottleneck of low piezoelectric response in flexible ferroelectric polymers and provides a viable route for high-performance wearable electromechanical devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4245-4
The discrimination of volatile organic compounds (VOCs) at trace concentrations remains a critical challenge for environmental monitoring, industrial process control, and non-invasive disease diagnostics. Conventional electronic noses rely on sensor arrays comprising multiple chemically distinct receptors, which introduces fabrication complexity, calibration drift, and cross-sensitivity. Here, we demonstrate that a single-component Ti3C2Tx MXene (TM) sensor array, engineered through controlled surface chemistry and device architecture, generates independent and high-dimensional characteristics (IHC) sufficient for precise VOC pattern recognition. By exploiting the intrinsic heterogeneity of TM basal planes and edge sites, we achieve differential interaction motifs without expanding elemental composition. The array discriminates VOCs including acetone, ethanol, toluene, and hexane at concentrations down to 100 ppb with classification accuracy exceeding 95%. Principal component analysis reveals distinct clustering with cumulative variance of 92.3% captured by the first three principal components. The sensor exhibits a limit of detection of 50 ppb for acetone and response/recovery times of 12 s and 18 s, respectively. Long-term stability tests over 30 days show less than 5% signal degradation. This single-component strategy simplifies fabrication, reduces calibration overhead, and offers a scalable pathway for miniaturized, low-power VOC sensing platforms compatible with Internet of Things (IoT) deployment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4391-5
Self-assembled monolayers (SAMs) enable precise tuning of the ITO/active layer interfacial dipole, yet their impact on the crystallization kinetics of the overlying active layer remains poorly understood, limiting their potential in high-efficiency organic solar cells. This study introduces THPC, a self-assembling material with an extended carbazole core and heteroatom substitution, as a hole transport layer (HTL). Unlike the hydrophilic PEDOT:PSS, THPC exhibits low surface energy, providing a favorable template that extends the film formation kinetics of the PM6:L8-BO-X blend by nearly 1.4 times, mitigating the explosive nucleation prevalent in PM6-based active layers. This promotes a highly ordered fibrous morphology and enhances vertical phase separation. The deep work function of THPC (5.32 eV) increases the built-in potential, reduces interfacial trap density, and facilitates charge extraction. Consequently, non-radiative recombination loss decreases from 0.243 eV to 0.227 eV, and the open-circuit voltage rises from 0.866 V to 0.883 V, yielding a power conversion efficiency (PCE) of 20.19%, outperforming the PEDOT:PSS control (18.67%). This finding is confirmed across multiple Y-series acceptors, all approaching 20% PCE. Notably, the D18:L8-BO system achieves a PCE of 20.55%, demonstrating broad applicability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4321-x
Poly(ethylene oxide) (PEO)-based solid polymer electrolytes are leading candidates for solid-state lithium metal batteries due to their flexibility, processability, and interfacial compliance. However, the strong crystallization tendency of PEO and limited lithium salt dissociation result in low ionic conductivity and low Li+ transference number, exacerbating concentration polarization and interfacial instability. Introducing metal-organic framework (MOF) fillers into PEO matrices has emerged as an effective route to regulate polymer-chain packing and promote salt dissociation via Lewis acid-base interactions. Yet, most studies focus on cubic ZIF-8, whose saturated Zn coordination environment limits intrinsic Lewis acidity and restricts its ability to immobilize TFSI- anions. Simultaneously, simple physical blending often leaves discontinuous interfacial transport regions in composite electrolytes, so improved salt dissociation does not automatically translate into fast Li+ transport. Here we report a PEO-based composite polymer electrolyte, denoted as PZS, that couples monoclinic ZIF-8 (M-ZIF-8) nanosheets with a thin SiO2 layer. The design combines two complementary functions: the under-coordinated Zn sites in M-ZIF-8 provide strong Lewis acid centers to adsorb TFSI- and promote LiTFSI dissociation, while the hydroxyl-rich SiO2 shell improves compatibility with the PEO matrix and helps construct continuous interfacial Li+ transport pathways. Benefiting from this synergy, the optimized PZS electrolyte delivers an ionic conductivity of 8.3 × 10-4 S cm-1 and a Li+ transference number of 0.57 at 60 ℃, together with an electrochemical stability window of 5.2 V. Li||Li symmetric cells remain stable for over 1200 h at 0.1 mA cm-2, and LFP||Li full cells retain 80% of their capacity after 400 cycles at 0.5 C.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4480-1
Ternary organic solar cells (OSCs) incorporating a structurally compatible guest acceptor (C7-Cl) into the PM6:BTP-eC9 host system are demonstrated. The low Flory-Huggins interaction parameter between host and guest acceptors facilitates intimate mixing, optimizing molecular packing and energy-level alignment. High-sensitivity sEQE and EQEEL analyses reveal a reduced non-radiative energy loss (KE3) of 0.216 eV in the ternary device. Consequently, the optimized ternary OSC achieves a champion power conversion efficiency (PCE) of 20.02% and an improved T80 operational lifetime of 1065 h. This work establishes a feasible strategy via structurally compatible guest doping to simultaneously optimize vertical phase separation and suppress non-radiative loss, providing a facile and effective route toward high-performance and stable OSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4288-1
The high-temperature oxidation resistance of Cr2AlC MAX phase ceramics is severely compromised by rapid Al depletion and the formation of a brittle sub-surface Cr7C3 layer. This study elucidates how trace Y2O3 doping (0.25 and 0.5 wt.%) modulates the oxidation behavior of Cr2AlC at 1100 °C. The incorporation of 0.5 wt.% Y2O3 significantly suppresses the parabolic rate constant compared to undoped counterparts. This kinetic suppression is attributed to the Reactive Element Effect (REE), where Y3+ segregation at α-Al2O3 grain boundaries inhibits outward Al3+ diffusion, shifting the scale growth mechanism to inward oxygen diffusion control. Consequently, this retarded Al consumption prevents the decomposition of the Cr2AlC substrate into Cr7C3. While undoped specimens fail due to volume contraction and Kirkendall voiding associated with the Cr7C3 interlayer, specimens with the most effective doping content within the investigated range maintain a stable, atomically sharp α-Al2O3/Cr2AlC interface devoid of voids and decomposition products. The superior adhesion of this interface is attributed to three synergistic factors: the elimination of volumetric mismatch induced by phase transformation, the mechanical interlocking provided by Y-rich oxide pegs, and the intrinsically higher interfacial bonding strength of the α-Al2O3/Cr2AlC system as confirmed by DFT calculations. These findings provide a mechanistic framework for designing oxidation-resistant MAX phase ceramics via reactive element doping.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4488-x
Thermochromic smart windows based on hydrogels suffer from inevitable freezing at subzero temperatures and dehydration at elevated temperatures, severely limiting their year-round applicability. This study reports a hydrogel-derived liquid (HDL) smart window that circumvents these limitations through a solvent-exchange strategy. The HDL is synthesized by polymerizing a hydroxypropyl cellulose (HPC) and N-isopropylacrylamide (NIPAM) network in a water-glycerol binary solvent, followed by complete removal of the water phase via vacuum-assisted evaporation. The resulting anhydrous liquid exhibits a lower critical solution temperature (LCST) of 32 °C, with a solar modulation ability (ΔTsol) of 63.2% and a luminous transmittance (Tlum) of 88.1% in the clear state. Critically, the HDL remains optically switchable after 1000 hours at -40 °C and 1000 hours at 80 °C, with no observable phase separation or freezing. The smart window prototype demonstrates a 12.3% reduction in indoor cooling energy consumption in a simulated tropical climate and a 9.8% reduction in heating energy in a cold climate, compared to a commercial low-E glass. The liquid-state formulation enables facile large-area fabrication via roll-to-roll processing, with a demonstrated 30 cm × 30 cm prototype retaining 95% of the initial ΔTsol after 500 bending cycles. This work establishes a viable pathway for all-climate energy-efficient building envelopes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4300-3
The power conversion efficiency (PCE) of organic solar cells (OSCs) has surpassed 21% with the donor polymer D18, yet its processing from non-halogenated solvents like ortho-xylene (o-XY) remains inefficient due to uncontrolled film formation kinetics. Here, we systematically synthesize D18 polymers with molecular weights ranging from 41.6 kDa to 70.9 kDa to modulate crystallization kinetics. In-situ film drying studies reveal that lower molecular weights accelerate solidification, leading to excessive aggregation, while higher molecular weights slow it, causing insufficient phase separation. A medium molecular weight (D18-M) achieves a balanced crystallization rate, promoting favorable morphology and yielding a PCE of 20.55% with L8-BO as acceptor—one of the highest reported for non-halogenated solvent-processed OSCs. Energy loss analysis indicates that although low-molecular-weight polymers exhibit higher intrinsic luminescence, the blend film's emission is governed by exciton environment, which is dictated by morphology. This work underscores the critical role of molecular weight in controlling film formation and morphology, offering a simple yet effective strategy for high-efficiency, environmentally friendly OSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4239-2
The sluggish kinetics of the oxygen evolution reaction (OER) remains a bottleneck for efficient water splitting. NiFe-layered double hydroxides (LDHs) are promising OER catalysts, but their performance is often limited by the high-spin state of Fe3+ and poor structural stability. Here, we report a series of amino acid-intercalated iron-rich NiFe-LDHs (AA-NiFe-LDHs) synthesized via a facile one-step coprecipitation method. Intercalation of glycine, alanine, and valine into the interlayer galleries expands the interlayer spacing and induces a partial transition of Fe3+ from high-spin to low-spin state, as confirmed by X-ray absorption spectroscopy and Mössbauer spectroscopy. The low-spin Fe3+ enhances the intrinsic catalytic activity by optimizing the adsorption energy of oxygen intermediates. Among the series, the glycine-intercalated sample (Gly-NiFe-LDH) exhibits the best OER performance in 1.0 M KOH, with an overpotential of 240 mV at 10 mA cm−2 and a Tafel slope of 38 mV dec−1, significantly outperforming the pristine NiFe-LDH (280 mV, 52 mV dec−1). Moreover, Gly-NiFe-LDH shows excellent long-term stability, retaining 95% of its initial activity after 24 h of chronopotentiometry at 10 mA cm−2. The intercalation also increases the electrochemically active surface area by 2.3-fold and reduces the charge transfer resistance from 12.5 Ω to 4.8 Ω. This work demonstrates that amino acid intercalation is an effective strategy to modulate the spin state of Fe3+ and enhance the OER performance of NiFe-LDHs, providing a new avenue for designing high-efficiency, low-cost electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4246-5
Developing organic solar cells (OSCs) processable from green solvents without additives or post-treatments is essential for sustainable manufacturing, yet high power conversion efficiency (PCE) remains difficult due to limited morphology control. Herein, we develop a new electron-deficient building block, dithiazolo[4',5':3,4;5'',4'':5,6]benzo[1,2-d][1,2,3]triazole (DTzBT), which fuses benzo[d][1,2,3]triazole (BTA) with thiazole to leverage S/N-mediated non-covalent interactions, enhance planarity and lower the HOMO. To isolate side-chain effects, two DTzBT-based donors, namely PTzMe-F (N-methyl) and PTzEH-F (N-2-ethylhexyl), have been designed and synthesized. PTzMe-F exhibits poor solubility and miscibility with L8-BO, yielding 2.64% PCE (chloroform). PTzEH-F exhibits excellent processability and favorable morphology, delivering 17.61% PCE (chloroform) and 19.17% as-cast from toluene without any additive or post-treatments. In addition, the ternary LbL device based on PTzEH-F/L8-BO:PC71BM achieved an impressive efficiency of 20.27%. Comprehensive characterization indicates that 2-ethylhexyl side chains afford optimal solubility while preserving strong intermolecular interactions and favorable phase separation. DTzBT mitigates BTA’s HOMO-raising tendency via electron-withdrawing thiazole fusion, reconciling aggregation tunability with energy-level control. These results show that precise backbone and side-chain co-design enables green-solvent, additive-free processing for high-performance OSCs, advancing sustainable photovoltaic manufacturing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4250-0
Shape memory polymer (SMP)-based transfer printing offers a promising route for heterogeneous integration of flexible electronics, yet non-contact release reliability remains a critical bottleneck. This study systematically investigates the influence of pickup heating modes—localized versus global—on the release yield and energy-delivery mechanisms through combined experiments and finite element simulations. The localized heating mode concentrates strain energy at the interface, enabling controlled chip ejection with high yield, whereas global heating dissipates energy, leading to release failure. Quantitative analysis reveals that localized heating achieves a release yield of 100% under optimized conditions, compared to near-zero for global heating. The ejection velocity under localized heating is higher, which may induce chip bouncing on the receiver substrate, affecting transfer accuracy; however, this can be mitigated by adjusting release gap and laser parameters. The findings establish a theoretical framework for energy pathway design, providing guidelines for achieving high-yield, accurate non-contact release in laser-induced transfer printing. This work advances the practical application of SMP-based transfer printing for micro-LED displays and flexible electronics, addressing a key manufacturing bottleneck.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4201-0
Open fracture fixation faces dual critical challenges: bacterial infection and impaired bone healing. This study presents a rationally designed biomacromolecular network coating (Ti-GOED) on titanium alloy bone plates to simultaneously address these issues. The coating integrates antimicrobial and osteogenic components, achieving an optimal balance between antibacterial efficacy and biocompatibility. In vitro assays demonstrated that Ti-GOED eliminates over 99% of common pathogenic bacteria by inhibiting peptidoglycan synthesis, disrupting bacterial cell wall formation, compromising membrane integrity, and leading to intracellular DNA leakage and bacterial death. Concurrently, Ti-GOED enhances the proliferation and osteogenic differentiation of bone marrow mesenchymal stem cells (BMSCs) via activation of the PI3K-Akt and HIF-1 signaling pathways. In vivo animal experiments confirmed strong antibacterial and osteogenic properties. This work provides a strategy for developing antibacterial coatings on medical devices, with significant potential for preventing and treating infections post-fracture fixation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4292-4
The vast compositional space of high-entropy materials presents a fundamental challenge for catalyst discovery. Considering 21 candidate elements at a 1% atomic resolution, this combinatorial explosion exceeds 10 billion (>10^10) possibilities, rendering direct experimental exploration impractical. Furthermore, purely data-driven approaches often struggle to comprehend the intrinsic chemical roles of discrete elemental identities, yet they excel at mapping continuous concentration gradients. Recognizing this distinction, we transform this combinatorial explosion into a targeted optimization problem by decoupling elemental selection from compositional ratio refinement. Ultrafast carbon thermal shock (CTS) is first employed to screen viable elemental combinations and establish an optimal quinary framework. Machine learning (ML) is subsequently applied to optimize compositional ratios within this reduced space, where statistical modeling efficiently navigates the remaining high-dimensional landscape. Targeting the oxygen evolution reaction (OER) as a proof-of-concept, our hybrid framework pruned the search space from over 10^10 possible compositions down into 13 systems, ultimately identifying high-entropy oxide (HEO)-Fe17.57Co28.45Ni31.27Mo10.57Zr12.14 as the optimal catalyst. The optimized high-entropy oxide exhibits an overpotential of 240 mV at 10 mA cm−2 and sustains stable operation at 1 A cm−2 for over 600 h in 1 M KOH. Mechanistic analysis reveals that Mo electronically tunes oxygen-intermediate adsorption, while Zr enhances structural robustness, collectively enabling high activity and durability. This work demonstrates that bridging discrete physical screening with continuous data-driven optimization provides an efficient and generalizable pathway for navigating high-dimensional material frontiers.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4322-4
Ultrafast scintillators with low-nanosecond emission are essential for next-generation high-rate X-ray and particle imaging. Although Ce3+-activated scintillators inherently exhibit fast response characteristics, conventional Ce3+-doped hosts rarely achieve low-nanosecond ultrafast decay. Here, we report a high-entropy fluoride scintillator (HEFS), Ce:LaGdCaSrBaF12 (Ce:LGCSB), in the form of bulk single crystals. The severe lattice distortion arising from multi-cation disorder induces exciton localization and effectively suppresses exciton diffusion. Through the rapid relaxation of localized excitons, the high-entropy Ce:LGCSB single crystals deliver a decay time of 1.23 ns with a 94.6% fast-component contribution and without any noticeable slow component. Through first-principles calculations, spectroscopic characterization, and transient dynamics analysis, we reveal that the ultrafast response originates from accelerated Frenkel exciton (FE) recombination enabled by the high-entropy environment. This work establishes entropy-engineered fluorides as promising ultrafast scintillator platforms and proposes a general strategy for extending sluggish diffusion effects to the excitonic scale, offering new opportunities for improving scintillation timing performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3607-9
Enhancing light olefin selectivity and extending catalytic durability remain critical challenges for ZSM-5 zeolites in methanol-to-olefins (MTO) conversion, primarily due to inherent diffusion restrictions along the MFI b-axis and poor coke accommodation. Here, we report a hierarchically single-crystalline ZSM-5 sheet architecture featuring interconnected multiscale porosity and a remarkably reduced b-axis thickness (<50 nm), quantitatively verified by three-dimensional electron tomography. Real-time confocal laser scanning microscopy tracking demonstrated significantly enhanced molecular diffusivity compared to conventional micron-sized ZSM-5 (Micro-ZSM-5). This engineered structure distributes abundant aluminum sites on highly accessible diffusion pathways, achieving an enlarged coke accommodation of 16.31 wt% with a coke deposition rate of 0.59 mg g−1 h−1, only one third of that in Micro-ZSM-5. In continuous MTO operation, the hierarchical ZSM-5 sheet (Hier-ZSM-5-S) maintained an average ethylene and propene selectivity of 63.5% for 22.2 hours (WHSV = 3.6 h−1, T = 480°C), which was 19% higher and 6.5 times longer than Micro-ZSM-5, respectively. This hierarchically shortened b-axis structure establishes a generalizable paradigm for enhanced diffusion and coke accommodation in precisely designed pore systems, applicable to various reactions.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4114-5
The precise and controllable synthesis of one-dimensional (1D) and two-dimensional (2D) heterostructures, coupled with the manipulation of their atomic and electronic configurations, is of paramount significance. However, due to the synthetic challenges associated with graphyne (GY) materials, their integration into 1D/2D heterostructures remains considerably difficult. Herein, we demonstrate a post-synthetic intercalation strategy for tellurium onto Ag(111), enabling the controllable fabrication of 1D-GY-nanowire/2D-AgTe-monolayers heterostructures. Scanning-probe microscopies are employed to characterize morphological evolution during the intercalation process. Scanning tunneling spectroscopy results confirm that AgTe monolayer intercalation induces interfacial decoupling of the graphyne nanowires. Density functional theory calculations demonstrate that work function-driven Fermi level modulation via interfacial charge engineering assigns the 1D-GY-nanowire/2D-AgTe-monolayers heterostructures as type-I heterostructures. Our work not only significantly advances the fundamental understanding of interfacial interactions in 1D/2D heterostructures but also presents a scalable strategy for designing heterostructures with tailored electronic functionalities, thereby opening new avenues for applications in advanced nanoelectronics and optoelectronic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3865-1
Seawater electrolysis (SWE) is a reusable and convenient avenue for producing hydrogen, offering a promising solution to the energy crisis and global warming. However, poor electrolytic efficiency and irreversible corrosion caused by high concentrations of chlorine severely hinder the commercialization of SWE. To address these challenges, numerous strategies have been proposed in recent years, involving theoretical innovations, directional catalyst design, and electrolyser modification. This review provides a systematic summary of the chlorine-related challenges and solutions encountered in SWE. The chlorine-related theoretical knowledge and challenges in SWE systems are first emphasized. Subsequently, multiple anodic chloride suppression strategies are introduced from three aspects: directional regulation of oxygen evolution catalysts, optimization of electrolyte compositions, and ingenious upgrades of electrolytic cells. Finally, future challenges and development directions for large-scale application of SWE technology are explored. This review offers an in-depth analysis of the chlorine-related challenges encountered in the industrialization of SWE, aiming to accelerate the advancement of this technology toward practical applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3579-8
Metal sulfides such as CdS are promising for solar-driven H2O2 production but suffer from rapid charge recombination and severe photocorrosion. This study introduces a dual-functional strategy synergizing sulfur vacancy (Sv) engineering and polydopamine (PDA) coating to overcome these limitations. Sv-CdS nanorods were hydrothermally synthesized with tunable vacancy concentrations, followed by in-situ PDA deposition to construct a direct Z-scheme heterojunction. X-ray photoelectron spectroscopy (XPS) and density functional theory (DFT) calculations reveal that the introduction of S vacancies reduces the work function of CdS, facilitating energy level alignment with PDA and enabling efficient electron transfer from CdS to PDA. By tuning the concentration of S vacancies, the charge transfer efficiency can be maximized. As a result, the photocatalytic H2O2 production rate reaches 2539.5 μmol g−1 h−1 under visible light, and further increases to 4395.5 μmol g−1 h−1 after PDA encapsulation—15.6 times higher than that of pristine CdS. Concurrently, PDA enhances O2 adsorption and protects Sv-CdS from photocorrosion. Sv-CdS@PDA exhibited superior photostability compared to Sv-CdS after three consecutive photocatalytic cycles. Mechanistic studies suggest that the Z-scheme heterojunction effectively separates electron-hole pairs: electrons in the conduction band of CdS reduce O2 to ·O2−, which is subsequently converted to H2O2, while holes in the valence band of Sv-CdS oxidize water to replenish O2. This work provides fundamental insights into engineering charge transfer and stability in sulfide-based photocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3660-5
High-sensitivity piezoelectric ceramics with high piezoelectric constants (d33) are crucial for miniaturized, low-power, and high-efficiency transducers. However, conventional performance enhancement relies on intrinsic parameter modulation, which is limited and blind. This study introduces a performance-driven metamaterials creation model to develop structure-function-integrated piezoelectric materials. We systematically investigated the effects of metastructure design on d33 across two-dimensional straight rod (SR) structures, three-dimensional dot-matrix (Octa) structures, complex triply periodic minimal surface (TPMS) structures, and hybrid Octa&SR structures. The results demonstrate that metastructures combining high polarization charge conversion efficiency with low compression modulus (stiffness) effectively enhance d33. The SR structure exhibited optimal polarization charge conversion, the Fks-Shellular (FksS) structure within TPMS showed low stiffness, and the Octa&SR structure combined both properties. Notably, all three structures displayed exceptional piezoelectric performance. Specifically, the FksS structure achieved a substantial d33 of 194 pC/N, a 24% enhancement over conventional solid BaTiO3, while maintaining isotropic and stress-insensitive properties. This work elucidates the mechanism for designing piezoelectric metastructures, offering a novel pathway for developing high-performance, high-failure-strength piezoelectric materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3539-5
MXene-based layered films are promising for electromagnetic interference (EMI) shielding, yet achieving highly ordered structures in scalable production remains challenging. Here, we report a facile centrifugal casting method for fabricating MXene/polyvinyl alcohol (MXene/PVA) films with highly oriented and compact layered structures. During centrifugal casting, the viscous fluid experiences strong shear and centrifugal forces along tangential and normal directions, respectively, inducing compact and oriented arrangement of MXene nanosheets. Consequently, the Herman's orientation factor increases from 0.681 to 0.794 as rotation rate rises from 0 to 4000 r/min. Accordingly, tensile strength and toughness improve from 55.2 to 191.1 MPa and from ~0.8 to 2.5 MJ/m³, respectively. The highly oriented and compact layered structure with ultrathin thickness (~8 μm) enables a high absolute electromagnetic shielding effectiveness (SSE/t) of 21029 dB cm²/g. Moreover, increased orientation reduces infrared emissivity to 0.248, endowing the film with excellent thermal camouflage capability. This work presents an effective strategy for constructing high-performance MXene-based layered films.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3559-5
Polyamide (PA) membranes are promising for lithium extraction from spent lithium-ion battery (LIB) leachate but face a trade-off between selectivity and permeability. Here, we demonstrate that nascent PA membranes post-grafted with triaminoguanidinium (TAG) monomers (PA-TAG membranes) gain expanded ion passage channels (0.8–7.1 Å) and enhanced positive charge, achieving high-performance lithium separation. The PA-TAG membrane exhibits a pure water permeance (PWP) of 15.5 L m−2 h−1 bar−1, superior divalent ion rejection (~98%), and an excellent separation factor (~30), significantly outperforming pristine PA membranes. In a simulated acidic battery leachate, the PA-TAG membrane achieved a relative volumetric lithium recovery rate of 48.2% after a two-stage nanofiltration process, with the Li+/M2+ mass ratio of the second permeate reaching 53.35, 445 times that of the feed (0.12). The membrane maintained stable performance over 45 hours of nanofiltration and resisted acidic conditions (pH=2) for at least 20 days. These results highlight the potential of PA-TAG membranes for efficient lithium extraction from acidic battery leachate, addressing the critical need for sustainable recycling of spent LIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3698-5
The oxygen evolution reaction (OER) is a critical bottleneck in next-generation sustainable energy systems due to its sluggish kinetics. Developing cost-effective, high-efficiency electrocatalysts requires understanding the dynamic structural evolution at electrode-electrolyte interfaces under operating conditions. In situ techniques are invaluable for identifying active centers and monitoring key intermediates. This review comprehensively summarizes recent advances in cutting-edge in situ methods for characterizing OER electrocatalyst structure evolution. It provides a brief overview of active motifs and robust structures using multiple in situ correlative techniques, establishing essential structure-performance relationships and updating mechanistic understanding at atomic scale under realistic conditions. Key challenges and perspectives are highlighted to promote rational design of promising electrocatalysts for efficient oxygen-associated electrocatalysis and electrosynthesis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3627-x
Polar exploration demands robotic systems capable of operating at extreme low temperatures, yet existing electronic skins (e-skins) fail due to polymer brittleness and impaired self-healing. Here, we report a supramolecular elastomer strategy that enables highly stretchable, self-healing, and sensitive e-skins functional at −78 °C. The elastomers are based on a poly(dimethylsiloxane) (PDMS) backbone (Tg = −127 °C, Tb = −150 °C) functionalized with kinetically reversible quadruple hydrogen-bonding motifs (2-ureido-4[1H]-pyrimidone, UPy) in side chains (S-UD) or main chains (M-UD). At −78 °C, S-UD elastomers exhibit superior stretchability, with optimized S-U1.2D0.8 achieving elongation at break of ~3257%, 3.4 times that of PDMS controls and exceeding M-U1.2D0.8 (~2474%). Self-healing efficiency after 24 h at −78 °C reaches ~75.9% for S-UD versus ~34.3% for M-UD, with visual scratch disappearance only in S-UD. Density functional theory (DFT) analysis reveals that S-UD possesses more thermodynamically favorable chain convergence, enhancing cryogenic self-healing. The optimized S-UD elastomer serves as an excellent substrate for constructing ultralow-temperature-tolerant e-skins, addressing a critical bottleneck in polar robotics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3662-4
Luminescent thermometry has become a research hotspot due to its high spatial resolution, fast response, and non-invasive nature. However, achieving high-performance temperature imaging requires both luminescent materials with high temperature sensitivity and efficient imaging methods, which remains a significant challenge. In this study, a series of pure-phase rubidium germanate phosphors doped with manganese were synthesized and encapsulated into polydimethylsiloxane (PDMS) films to improve chemical stability. The dramatic temperature-dependent luminescence behavior of Mn4+ in the Rb2Ge4O9 matrix provides reliable and efficient methods for temperature sensing. The high-sensitivity temperature sensing capability of the Rb2Ge4O9:0.002 Mn4+ fluorescent film has been confirmed, leveraging temperature-dependent emission intensity, luminescence decay lifetime, and time-resolved intensity ratio techniques. Notably, Rb2Ge4O9:Mn4+ fluorescent film exhibits a strikingly high relative sensitivity of 17.03% K−1 at 330 K in the time-resolved thermometry scheme, which is the highest relative temperature sensitivity within the physiological temperature range known to us. High-performance temperature imaging of the fluorescent film is achieved through the time-resolved intensity ratio strategy with a best practical temperature resolution of 0.08 K at 325 K. Furthermore, the temperature images of an operating nickel circuit with a line width of 20 μm under different working currents were recorded, showing a clear circuit microstructure and temperature gradient. These findings pave a novel path for realizing high-performance temperature imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3642-4
High-density glass scintillators are promising alternatives to crystals for next-generation radiation detection due to their low cost, excellent physical and chemical stability, and processability. In this study, a series of Ce3+-activated gadolinium gallium borosilicate (GGBS x) glasses were synthesized via vacuum melt-quenching. With increasing Gd2O3 content, glass density increased from 5.86 to 6.05 g/cm3, and molar volume from 36.43 to 39.79 cm3/mol. Extended X-ray absorption fine structure (EXAFS) analysis revealed that in GGBS 1 glass, Ce3+ exclusively adopts a hexahedral [CeO6] configuration, while Gd3+ exhibits both hexahedral and octahedral coordination with a bond length of 2.35±0.1 Å and Debye-Waller factor σ2 of 0.0122±0.0015 Å2. As Gd2O3 content increased, shallow trap depth rose from 0.804 to 0.858 eV, while deep trap depth first increased from 0.948 to 1.434 eV then decreased to 1.010 eV. GGBS 1 glass exhibited high transmittance (~80%) in the visible range and a photoluminescence quantum yield of 78.4%. Under X-ray irradiation, its X-ray excited luminescence intensity reached 128.5% of that of Bi4Ge3O12 (BGO) crystal, with a spatial resolution of 29.1 lp/mm, approaching the highest reported for glass scintillators. Under γ-ray excitation, it achieved a light yield of 1058 photons/MeV and an energy resolution of 23.7% at 662 keV. These results indicate that GGBS 1 glass scintillator warrants further development for applications in X-ray imaging and γ-ray spectroscopy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3610-7
Electrochemical CO2 reduction reaction (CO2RR) offers an attractive route to produce value-added multicarbon (C2+) products, yet suffers from competing hydrogen evolution and monocarbon production. Here, we propose a dual-confinement effect on CO2 reactant and *CO intermediate, induced by tuning the pore configuration of reconstructed covalent organic frameworks (RC-COFs). The highly crystalline microporous RC-COF-1, when coated on a Cu electrode, enhances local CO2 concentration and restricts CO diffusion, thereby promoting C-C coupling. In acidic electrolyte, the RC-COF-1@Cu electrode achieves a maximum C2+ Faradaic efficiency (FE) of 67.0% at 500 mA cm−2, while maintaining a total carbon product FE above 90% across a broad current density range (100–500 mA cm−2). Experimental and theoretical analyses confirm that the ordered micropores of RC-COF-1 modulate reactant adsorption and intermediate diffusion, leading to improved C2+ selectivity. This work underscores the critical role of COF pore architecture in microenvironment engineering for heterogeneous catalysis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3598-1
Embedding a dielectric layer between as-synthesized graphene nanoribbons (GNRs) and metal surfaces represents a powerful strategy to achieve electronic decoupling, thereby enabling the extraction of these ribbons' intrinsic electrical properties. Although several reports have documented dielectric intercalation between GNRs and metal substrates, studies on Ag(111) substrates are limited. Here, we demonstrate a semiconducting AgTe monolayer intercalation method to achieve electronic decoupling between as-synthesized GNRs and an Ag(111) substrate. Using low-temperature scanning tunneling microscopy, we directly observed the AgTe intercalation process at the GNR/Ag(111) interface. By combining scanning tunneling spectroscopy and density functional theory calculations, we elucidate the critical role of AgTe monolayer intercalation in reducing the interaction between as-synthesized GNRs and the Ag(111) substrate and observe the near-intrinsic electrical properties of the GNRs. Our findings offer a practical and effective strategy for intercalating AgTe monolayers between carbon-based nanomaterials and Ag(111) substrates, facilitating the unambiguous characterization of the near-intrinsic electronic properties of these materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3722-3
Magnesium alloys are promising biodegradable bone implant materials due to their biocompatibility and mechanical compatibility, but rapid degradation and postoperative bacterial infection limit clinical application. Here, zeolitic imidazolate framework-8 (ZIF-8) and 3,4,9,10-perylenetetracarboxylic diimide (PD) composite coatings (ZIF-8@PD) were fabricated in situ on micro-arc oxidation (MAO) coated AZ31 alloys via two-step and one-step (OS) methods. The MAO/ZIF-8@PD and MAO/ZIF-8@PD (OS) coatings reduced corrosion current density by three and two orders of magnitude, respectively, compared to MAO coating, due to the physical barrier of the 2D-co-3D MOF structure. Under 808 nm near-infrared laser irradiation, photothermal and photodynamic effects from PD, combined with contact killing by released Zn2+ ions, achieved bactericidal rates ≥99.5% against E. coli and S. aureus. Photothermal conversion efficiencies were 44.01% and 48.57% for the two-step and one-step coatings, respectively. The distinct Zn2+ sources led to different 2D-co-3D MOF structures, influencing degradation and antibacterial behavior. These coatings offer a strategy to enhance corrosion resistance and antibacterial activity of Mg alloys for biomedical applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3702-0
Construction of metal-mediated redox sites is an appealing approach to enhance photocatalytic CO2 reduction coupled with H2O oxidation. However, conventional static redox sites generally lack spatiotemporal matching during reaction processes due to the constraints of rigid structure and the linear scaling relationship of adsorbed species. Herein, an alkanolamine-Ir synergistic system was developed, where flexible monoethanolamine (MEA) molecules function as molecular ferries to selectively adsorb CO2 via carbamate formation, while adjacent Ir nanoparticles (NPs) serve as H spillover hubs that relay protons, creating spatiotemporal adaptability that synchronizes CO2 reduction and water oxidation. In addition, time-resolved in situ spectroscopy directly captures the rapid transformation of carbamate intermediates concurrent with sustained IrOOH intermediates formation. Microkinetic modeling further demonstrates that the MEA-Ir modified system (M-Ir/ACN) creates interconnected H spillover networks between Ir NPs and MEA, facilitating efficient proton transport that drives *COOH formation with a favorable thermodynamic energy. As a result, the M-Ir/ACN achieves a 20-fold increase in CO production compared to the pristine sample while maintaining high stability throughout 45 h of continuous operation. This study presents that flexible molecular ferries boost CO2 adsorption, and deciphers how flexible molecular-metal synergy directs the trafficking of CO2-derived intermediates toward highly efficient CO2 photoreduction.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3674-2
Enhancing catalytic activity is a core objective in catalyst design, with active site accessibility being a critical determinant. Polyoxometalate-based metal-organic complexes (POMOCs), combining advantages of POMs and MOCs, offer potential for constructing catalysts with highly accessible active sites. In this study, a series of POMOCs were synthesized using different POM templates: [CoII1.5(L)1.5(PMo12O40)(H2O)4]·3H2O (Co-PMo12), [CoII1.5(L)1.5(PW12O40)(H2O)4]·3H2O (Co-PW12), [CoII2(L)2(SiW12O40)(H2O)4]·11H2O (Co-SiW12), and H[CoII2.5(L)3(P2W18O62)(H2O)8]·10H2O (Co-P2W18). These were characterized by FT-IR, PXRD, and single-crystal X-ray diffraction. Catalytic activity differences for olefin epoxidation were attributed to distinct accessibility of Co(II) sites upon thermal activation. Notably, Co-P2W18 achieved 99% yield of 1,2-epoxycyclooctane within 3 hours at room temperature using O2 as oxidant, owing to highly accessible unsaturated Co(II) sites. This performance is superior to most reported catalysts. The reaction mechanism was investigated using density functional theory. The catalyst exhibited excellent stability over five cycles, with FT-IR, PXRD, and XPS confirming structural and oxidation state integrity. This work highlights the potential of POMOCs in designing catalysts with highly accessible active sites for enhanced catalytic activity.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3716-x
Flexible pressure sensors (FPSs) are pivotal for fall detection and rehabilitation training, yet conventional synthetic-based sensors suffer from resource-intensive manufacturing, high costs, and environmental pollution. This study introduces a sustainable fabrication strategy for FPSs using natural materials. Electrodes were fabricated by treating natural wood strips with a flame retardant, converting them into high-quality graphene via cost-effective infrared laser processing, and transferring onto starch-based substrates. The dielectric layer comprised an electrospun composite nanofiber membrane of cyclodextrin and carbon nanotubes. The resultant capacitive FPS exhibited high sensitivity (2.15 kPa⁻¹ within 0–10 kPa), a low detection limit (~6.5 Pa), rapid response and recovery times (29 ms and 39 ms), and excellent long-term stability exceeding 5000 cycles. Biocompatibility was outstanding (cell viability >98%), and the sensor fully degraded within 6 hours. Integrated with wireless technology, the sensor enabled a fall detection and rehabilitation monitoring system. Data processing utilized a Tiny Machine Learning module on a mobile platform, transmitting data to a cloud-based system. The system accurately identified five common fall postures and assisted clinicians in guiding rehabilitation exercises, achieving recognition accuracies of 99% and 100%, respectively. This work offers a sustainable healthcare solution for elderly care, addressing environmental and economic limitations of existing FPS technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3704-0
The escalating demand for energy storage systems capable of delivering high energy density alongside ultrafast charging and discharging has exposed the limitations of conventional lithium-ion batteries (LIBs), particularly in applications such as electric air vehicles, portable medical devices, and grid-scale storage. Organic cathode materials offer tunable molecular design but suffer from sluggish ion diffusion kinetics, especially under high-rate and low-temperature conditions. This study introduces a 2D vertically ladder-like polymer (2DVLP) synthesized from tribenzoquinoline tribenzoquinone (TTQ) via a 2D polymerization strategy. The polymer features a layered nanosheet structure with densely distributed carbonyl (C=O) redox-active sites serving as Li+ storage centers. Interlayer micropores (0.4–2.0 nm) and structural defects facilitate vertical Li+ diffusion, while weak van der Waals interlayer interactions (no π–π stacking) enable horizontal Li+ intercalation. Coin-type half-cells using 2DVLP cathodes demonstrated outstanding room-temperature performance: 2DVLP-1 and 2DVLP-2 achieved specific capacities of 302 and 291 mAh g−1 at low current densities, respectively. The cross-flow design—combining vertical and horizontal ion transport pathways—effectively mitigates concentration polarization, enabling ultrafast charging. This work provides a scalable strategy for developing high-power organic cathodes, addressing critical bottlenecks in fast-charging energy storage.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3728-5
Biological intelligence achieves exceptional energy efficiency and environmental adaptability, exemplified by the human brain's ~20 W resting power consumption. A key strategy is the use of multi-ions as signal carriers for transduction and processing. Iontronics, employing ions instead of electrons, offer a promising route to low-energy, heat-dissipation-free devices for memory, sensing, and neuromorphic computing. However, conventional iontronics require external voltage bias to drive ion motion, complicating miniaturization and integration. Here, we highlight a recent breakthrough by Guo et al. reporting a bias-free iontronic memory sensor ('memsensor') that operates by controlling surface ion migration. The device couples vanadium dioxide (VO2) with a low-work-function indium (In) patch. Upon immersion in NaCl solution, In3+ ions generated electrochemically within the Debye length are driven by the intrinsic surface electric field to diffuse into the VO2 surface, inducing an insulator-to-metal phase transition and a measurable, non-volatile change in surface conductance. This conductance state correlates with NaCl concentration and can be reversibly restored by H2O2 treatment. The memsensor emulates the gustatory plasticity of C. elegans, mimicking the response dynamics of ASEL and ASER neurons. In a proof-of-concept, a model boat equipped with the memsensor exhibits adaptive chemotaxis: after 'starvation' training in high NaCl concentration, it avoids high-concentration zones; conversely, after training in low concentration, it migrates toward high-concentration zones. This work demonstrates a bias-free strategy for programmable memory and sensing, potentially advancing autonomous microsystems and bioinspired electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3772-y
Conformal contact between functional electronic films and biological surfaces is critical for long-term device stability, high signal sensitivity, and favorable signal-to-noise ratio. Traditional transfer methods, such as soft stamps and pad printing, often involve mechanical pressing, leading to poor conformality, localized stress concentration, or structural failure. Alternative strategies, including geometric engineering of non-stretchable materials or using stretchable organic alternatives, mitigate these issues but increase design complexity and reduce fabrication efficiency. Here, we highlight a novel 'drop-printing' strategy introduced by Li et al. that leverages capillary force to manipulate a water droplet to pick up a thin film, transfer it to a target substrate, and print it onto the surface. As the droplet evaporates, the film conformally wraps the surface. The droplet acts as a lubricating layer, while interfacial liquid penetrating microstructures generates capillary pressure, facilitating shape-adaptive deformation and significantly reducing stress concentration. The final positioning and conformality are governed by droplet behavior on the target surface. This approach achieves positional deviation of less than 20 μm via regulation of three-phase contact lines. The strategy enables damage-free conformal wrapping of non-stretchable films onto three-dimensional biological surfaces, as demonstrated by drop-printed silicon microfilm conformally wrapping on a rat brain, with successful NIR laser stimulation triggering forelimb movement and synchronized brain electrophysiological signals. This gentle, high-precision method addresses the pressing need for low-stress conformal bioelectronics, offering a general solution for diverse biological interfaces.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0020
Ammonia borane (AB) is a promising hydrogen storage material due to its low molecular weight and high hydrogen content. The development of low-cost, high-activity catalysts for AB hydrolysis is critical for industrialization. In this work, CuO nanosheets (CuO NS) were synthesized via a solvothermal method under alkaline conditions using anhydrous copper chloride as precursor. Subsequently, low-temperature phosphating converted CuO NS into Cu3P@CuO nanosheets (Cu3P@CuO NS). The morphology and structure were characterized by SEM, TEM, AFM, XRD, and XPS. The catalytic performance for AB hydrolysis was evaluated, revealing that at a phosphating ratio of m(CuO NS)/m(NaH2PO2)=1 (0.1 g each), Cu3P@CuO NS exhibited excellent activity with a TOF of 57.23 min−1 and an apparent activation energy of 44.31 kJ/mol. The reaction followed pseudo-first-order kinetics with respect to catalyst amount and pseudo-zero-order kinetics with respect to AB concentration. The superior performance is attributed to the abundant active sites exposed by the nanosheet structure. Given the extremely low cost, Cu3P@CuO NS is a promising alternative to noble metal catalysts for hydrogen generation from AB.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512072
Drainage pipeline defect detection predominantly relies on closed-circuit television (CCTV) inspection, which is labor-intensive, inefficient, and prone to missed detections. Although deep learning-based object detection has been applied, it suffers from low precision, recall, and speed in practical scenarios. This study proposes an engineering-oriented detection scheme achieving high recall and low miss rates. The annotation phase employs a cross-frame strategy combining manual labeling of first and last frames with interpolation and tracking-based refinement. Data preprocessing introduces perceptual hashing to identify similar images, enhancing training efficiency. For detection, a Faster R-CNN model is enhanced with Focal Loss to focus on hard examples, defect classification and grading, and a dynamic threshold strategy to improve recall. Validated on 5,068.72 m of real pipeline data, the method achieves a recall rate exceeding 98% across 16 defect categories, a miss rate of only 2% for grade 4 defects, and a 425% improvement in per-segment detection efficiency compared to manual screening. These results demonstrate the method's effectiveness in balancing recall, miss rate, and speed for engineering deployment.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025111002
Epidemiological studies have established a significant association between exposure to environmental pollutants (EP) and the risk of lung adenocarcinoma (LUAD). This study integrates network toxicology and multi-omics analysis to elucidate the EP-LUAD molecular regulatory network and identify key regulatory genes, thereby revealing novel mechanisms of environmental carcinogenesis. Transcriptomic data from GEO and TCGA databases yielded 4,971 and 4,488 disease-related targets, respectively. Integration of toxicology databases (TargetNet, Swiss Target Prediction, CTD, SEA) identified 24,860 potential targets for eight common pollutants (SO2, NO, CO, NO2, O3, benzene, toluene, and polycyclic aromatic hydrocarbons). Intersection of these datasets produced 1,536 EP-LUAD common target genes. Protein-protein interaction network analysis identified 247 core targets. Machine learning selected five key genes: AGER, CAV1, CD44, CEP55, and GNB3, which demonstrated robust diagnostic and prognostic efficacy. Their expression correlated with immune cell infiltration, including CD4+ memory T cells and macrophages. Single-cell RNA sequencing revealed epithelial cell-specific expression patterns. Molecular docking confirmed stable pollutant-target binding, with PAH showing highest affinity for CD44 (binding energy −9.32 kcal·mol−1) and GNB3 (−8.32 kcal·mol−1). These findings establish AGER, CAV1, CD44, CEP55, and GNB3 as core molecular mediators of pollution-related LUAD. The high-affinity binding of PAH to CD44 and GNB3 underscores its carcinogenic potential. This study constructs a multi-level regulatory network for EP-LUAD, revealing underlying molecular mechanisms and providing novel potential targets and theoretical basis for early warning and intervention.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010302
Cadmium (Cd) contamination of agricultural soils poses significant economic and health risks. While extensive research has focused on Cd accumulation in staple crops like rice, data on oilseed crops remain scarce, hindering safety assessments of edible oils and oilseed meals. This study investigated Cd accumulation and translocation in rapeseed (Brassica napus) grown in You County, Hunan Province, a region severely contaminated with Cd. Rhizosphere soil and plant tissues (roots, stems, seeds) were collected and analyzed for Cd concentrations. Results showed that approximately 71% of rhizosphere soil samples exceeded the agricultural soil pollution risk screening value for Cd, indicating high ecological risk. Cd concentrations in roots and stems were (0.49 ± 0.39) mg·kg⁻¹ and (0.54 ± 0.31) mg·kg⁻¹, respectively, comparable to or higher than soil Cd levels (0.51 ± 0.31) mg·kg⁻¹, with elevated bioaccumulation and translocation factors. This suggests that improper disposal of rapeseed roots and stems, such as returning them to fields or burning, could lead to secondary Cd pollution. In contrast, Cd bioaccumulation and translocation factors in seeds were less than 1, and Cd concentrations in seeds, oil, and oilseed meals were relatively low. Comparative analysis with sesame, camellia oleifera, and peanut indicated that rapeseed-derived oil and meal contain lower Cd levels, positioning rapeseed as a promising low-Cd-accumulating edible oil crop for cultivation in Cd-contaminated areas.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024122101
Bicarbonate and carbonate ions (HCO3−/CO3^2−) are ubiquitous in wastewater and readily scavenge strong oxidants, leading to the formation of carbonate radicals (CO3·−) in radical-based advanced oxidation processes. This study investigated the influence of HCO3−/CO3^2− on the degradation kinetics of sulfamethazine (SMR) in a UV/TiO2 system. The presence of HCO3−/CO3^2− enhanced the degradation rate of SMR by sixfold compared to UV/TiO2 alone. Radical quenching experiments identified CO3·− as the primary reactive species responsible for the enhanced degradation, with hydroxyl radicals (·OH) also contributing. To quantitatively delineate the roles of reactive species and account for water matrix effects, a kinetic model was constructed using Kintecus software. The model accurately predicted SMR degradation over time and the contributions of individual radicals, demonstrating good predictive capability. Application of the model to real wastewater predicted that CO3·− is the dominant radical responsible for SMR degradation. These findings highlight the critical role of carbonate radicals in UV/TiO2 processes and provide a robust modeling framework for predicting the fate of pharmaceuticals in carbonate-rich waters.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604009
Biological nitrogen removal in wastewater treatment plants (WWTPs) is often limited by insufficient influent carbon sources, necessitating external carbon addition to enhance denitrification. Conventional single carbon sources, such as sodium acetate, frequently fail to meet the metabolic demands of complex microbial communities, compromising nitrogen removal efficiency and stability. Composite carbon sources, by providing multiple electron donors, can improve metabolic cooperation among microorganisms, yet their underlying microbial mechanisms remain insufficiently understood. In this study, activated sludge from a municipal WWTP was used to investigate the microbial mechanisms of composite carbon sources during denitrification. Batch denitrification experiments were conducted in combination with metagenomic and metatranscriptomic analyses to systematically characterize microbial community structure and functional gene expression under different carbon source conditions. Results showed that, compared with sodium acetate as the single carbon source, the composite carbon source system (sodium acetate: sodium succinate: ethanol = 2:1:3) increased the denitrification rate from (6.822 ± 0.141) mg/(L·h) to (8.370 ± 0.186) mg/(L·h), representing a 22.7% improvement, while reducing N2O accumulation by approximately 55%. Metagenomic analysis revealed that Ottowia, Rubrivivax, Thauera, and Zoogloea were the dominant denitrifying genera. Metatranscriptomic results further demonstrated that the composite carbon sources significantly upregulated the transcription of key denitrification genes, with nirS, norB, and nosZ increasing by 37.8%, 27.4%, and 48.6%, respectively. In addition, the composite carbon sources promoted complementary carbon metabolic strategies among different microbial communities, enhancing electron donor supply and improving denitrification efficiency. These findings indicate that composite carbon sources synergistically enhance denitrification performance through regulation of functional gene transcription in complex microbial communities, providing a theoretical basis for carbon source optimization in WWTPs.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604027
Magnesia production processes generate carbon monoxide (CO) emissions, yet publicly available measured data on CO emission factors for these processes remain scarce, constraining the accuracy of emission accounting and mitigation assessment in the industry. To address this data gap, this study selected three representative magnesia-producing enterprises in Anshan, Liaoning Province, China, covering three typical technological routes: the two-stage calcination process (light burning-briquetting-shaft kiln dead burning), the suspension calcination-dead burning sintering process, and the electric arc furnace melting process. Under the condition that enterprises were not equipped with online CO monitoring modules, an estimation approach coupling manual measurements with conventional indicators from the Continuous Emission Monitoring System (CEMS) was developed. By establishing characteristic concentration ratios between CO and nitrogen oxides (NOx) or particulate matter (PM), and combining them with annual CEMS monitoring data, product-level CO emission factors were calculated. The results showed that the CO emission factors for the two-stage calcination process, the suspension calcination–dead burning sintering process, and the electric arc furnace melting process were 5.35, 5.18, and 1.40 kg/t, respectively, among which the emission level of the electric arc furnace melting process was significantly lower than that of sintering-based processes. This study provides enterprise-level measured CO parameters for the magnesia industry, filling the data gap in emission factors for typical technological routes. It also proposes an emission factor estimation method applicable under conditions where online CO monitoring data are unavailable, which can provide methodological support for pollutant emission accounting and emission inventory development in similar data-constrained industries.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225246
The development of efficient catalyst classification technologies is crucial for optimizing fluid catalytic cracking (FCC) and catalytic pyrolysis coupling processes, where distinct particle size distributions are required for different reaction pathways. In this study, a large-scale cold-model experimental platform of a multi-arm vortex separator is established to explore the influence of operating conditions on classification behavior. Systematic experiments are conducted by changing ejection gas velocity (8~20 m/s), inlet particle concentration (30~70 g/m3), and bed linear velocity (0.15~0.25 m/s). The results demonstrate that ejection gas velocity governs classification sharpness by controlling the entrainment of fines within the coarse fraction. The increase in ejection gas velocity enlarges the upward axial gas velocity inside the device, thereby enhancing the entrainment effect on particles near the vortex arm outlets. Increasing the ejection gas velocity from 12 to 16 m/s reduces proportion of fine particles in coarse components from 14% to 12%. The inlet particle concentration imposes competing effects on classification performance: while higher concentrations promote agglomeration and modify turbulence distribution, excessive loading intensifies fine-particle entrainment, thereby diminishing classification selectivity. The system maintains stable pressure drop characteristics under different bed linear velocities, with the pressure drop increasing by maximum of about 15% when the bed linear velocity is raised from 0.15 m/s to 0.25 m/s. Analysis of grade efficiency curves reveals classical S-shaped profiles with cut sizes (dc50) shifting under different operating regimes. Higher particle concentrations reduces dc50, favoring fine-particle removal, while higher ejection gas velocities enlarge dc50, moving the classification boundary toward larger sizes. These findings confirm the synergistic effect of ejection gas velocity and inlet concentration, highlighting that rational parameter matching can simultaneously improve efficiency and selectivity. Beyond the experimental findings, this work emphasizes the broader applicability of multi-arm vortex separators in refining and petrochemical processes. By enabling precise adjustment of particle size distribution, the system offers a promising pathway for enhancing catalyst utilization, extending catalyst lifetime, and facilitating process intensification in coupled FCC-pyrolysis units.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3882-y
Organic semiconductor crystals with well-defined morphologies are highly desirable for high-performance optoelectronic devices, yet precise control over their growth remains a challenge. Here, a novel donor-acceptor (D-A) molecule, TQDPT, has been successfully developed, featuring a rigid π-conjugated acceptor core composed of thiazoloquinoxaline and naphthalene, coupled with phenylphenothiazine donors. This study presents a temperature-mediated crystallization strategy for precisely controlling the morphology and carrier transport properties of TQDPT single crystals. By systematically investigating the growth kinetics across a controlled temperature range (15–35°C), we reveal a distinct transition from needle-like structures to plate-like crystals, with tunable average widths spanning from around 2.8 to 30.1 μm. This morphological evolution is driven by temperature-dependent molecular diffusion and nucleation kinetics. Significantly, the plate-like crystals grown at 25°C exhibit an order-of-magnitude enhancement in mobility compared to needle-like counterparts, while higher temperatures of 35°C yield broader crystals with improved carrier mobility and device stability. This work highlights the critical role of temperature as a pivotal parameter in the dimensional and electronic optimization of organic crystals, offering an attractive approach to optimize functional materials for advanced optoelectronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3487-x
Continuous carbon fiber-reinforced ZrB2-SiC ceramic matrix composites are promising thermal protection materials for hypersonic vehicles and reusable spacecraft. Although injection-assisted vacuum impregnation (IVI) offers advantages such as shorter processing cycles, lower costs, and reduced fiber damage compared to conventional methods, phenolic/acetone-based IVI systems yield composites (designated as CPS) with limited ceramic contents. To address this, an aqueous slurry-based IVI approach was developed, producing composites designated as CHS. After a single IVI cycle, CHS achieved a ZrB2 phase volume fraction of 25 vol.%, 47% higher than CPS, while reducing processing time by 49%. After chemical vapor infiltration, CVI-CHS composite exhibited a room-temperature compressive strength of 106.78±10.53 MPa, representing a 28% improvement over CVI-CPS. Crack propagation analysis revealed discontinuous zigzag patterns under compression, dominated by fiber bridging and pull-out energy dissipation mechanisms. Flexural results revealed both composites retain considerable strength (111.15±12.46 and 83.15±12.03 MPa) along with low flexural modulus (13.00±2.41 and 13.52±6.99 GPa) and high strain tolerance (1.32%±0.018% and 1.07%±0.34%). It is attributed to the anisotropy of fiber preforms and the elastic modulus mismatch among different phases, which hindered effective constraint of fibers by the matrix and, in turn, facilitated mitigation of stress concentration. Additionally, CVI-CPS demonstrated superior X-band electromagnetic interference (EMI) shielding (34–36 dB) compared to CVI-CHS (22–27 dB), resulting from synergistic effects between pyrolitic and deposited carbon in the matrix of the former. Both composites showed enhanced EMI shielding efficiency with increasing temperature up to 600°C. This eco-friendly aqueous IVI strategy enables high-performance, cost-effective thermal protection materials with higher ceramic loading and tunable multifunctional properties.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4043-3
In-plane InAs nanowires and nanowire networks are promising platforms for electronics, optoelectronics, and topological quantum computing due to their small electron effective mass, narrow bandgap, high electron mobility, strong spin-orbit coupling, and large Landé g factor. However, their selective area growth on CMOS-compatible group-IV substrates remains challenging. Here, we report the selective area growth of high-quality in-plane InAs nanowires and nanowire networks on Ge(111) substrates by molecular-beam epitaxy. Conventional selective-area epitaxy fails to simultaneously achieve good selectivity and continuity. To overcome this, we developed a metal-sown, single-indium-source two-step growth method, which attains both selectivity and continuity but yields nanowires with rough surfaces and lengths below 10 μm. We then introduced an upgraded metal-sown, dual-indium-source two-step growth method, successfully fabricating in-plane InAs nanowires and nanowire networks with smooth surface morphology and lengths exceeding 60 μm. By optimizing the As beam equivalent pressure, overgrowth at network junctions is effectively suppressed, resulting in uniform nanowire networks. High-resolution transmission electron microscopy and Raman spectroscopy confirm the high-quality single-crystalline nature and pure zinc-blende structure of the nanowires and networks. This work establishes a foundation for fabricating high-quality in-plane InAs/superconductor hybrid nanowires and nanowire networks on Ge substrates.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3779-1
Comprehensive mechanical properties, including hardness (H), elastic modulus (E), fracture toughness (KC), and wear resistance, are essential for oxide ceramics used in demanding environments. This work employs nanoindentation to evaluate these properties for RE3TaO7 (RE=La, Sm, Eu, Gd, Dy, Lu) and identifies the optimal calculation method for KC in brittle oxide ceramics. The ratio of indentation crack length to half-diagonal (l/α) is a key parameter: Eq. (3) is suitable when l/α < 1, while Eq. (4) applies when l/α > 1. The indentation energy method is invalid for brittle ceramics due to crack formation at high loads. RE3TaO7 oxides exhibit H of 5.8–14.9 GPa, E of 127.5–247.8 GPa, and KC of 1.0–2.0 MPa·m1/2, surpassing RE2Zr2O7 (KC 1.0–1.5 MPa·m1/2). Wear resistance, indicated by MDP, ranges from 0.55 to 0.67, outperforming RE2Zr2O7. The superior fracture toughness is attributed to weberite structure with crack deflection and tortuous propagation, contrasted with pyrochlore's straight cracks. These findings provide accurate nanoindentation-based methods for assessing mechanical properties of brittle oxide ceramics, facilitating material discovery and optimization for thermal barrier coatings and other high-temperature applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3782-0
Oral mucositis (OM) is a debilitating complication of cancer therapy, characterized by severe pain, mucosal barrier breakdown, and infection risk. Current hydrogel-based topical systems suffer from poor transmucosal permeation and lack of inflammatory microenvironment-triggered drug release. Here, we report a supramolecular strategy for designing guanosine-fibril hydrogels and derived microneedle patches. Tavaborole (Ta), crisaborole (Cr), and strontium (Sr2+) ions serve dual roles as structural building blocks and biofunctional agents. Unlike conventional G4·K+ fibrils, the unique G4·Sr2+-Ta/Cr fibrils incorporate Ta/Cr via boronic ester bonds on guanosine and Sr2+ through G-quartet cation recognition. This design mechanically reinforces the hydrogel through additional hydrophobic interactions and ion-pair recognition, while synergistically providing antimicrobial/anti-inflammatory effects (Ta/Cr), pro-angiogenic activity (Sr2+), and reactive oxygen species (ROS) scavenging (guanosine). The optimized gelation process enables fabrication of microneedle patches with pseudomembrane-penetrating capability and ROS-triggered drug release via boronic ester hydrolysis. In vivo mouse experiments confirm efficacy in controlling OM-associated inflammation, modulating oral microbiota homeostasis, and promoting angiogenesis at ulcer sites. This work demonstrates multifunctional integration via hierarchical structural design, extending guanosine supramolecular assemblies into bioactive platforms for OM treatment.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61104-3
Lithium/fluorinated carbon (Li/CFx) batteries are among the most promising high-energy-density primary batteries, yet substantial heat generation during discharge poses safety concerns, particularly for high-mass-loaded pouch cells. This study systematically investigates the effects of fluorination temperature on the structure and kinetics of fluorinated porous carbon (FPC) cathodes and on heat generation in Ah-level Li/FPC pouch cells. FPC samples with varying degrees of fluorination were synthesized by adjusting fluorination temperature, which influenced not only the F/C ratio but also the C–F bonding configuration, pore structure, and electronic transport capability. Pouch cells employing more highly fluorinated cathodes generated the most heat during discharge, with heat generation exhibiting clear stage dependence, predominantly in the 0–20% depth of discharge (DOD) range. Post-discharge structural characterization and kinetic analysis revealed that highly fluorinated FPC cathodes (FPC-250) undergo more concentrated LiF accumulation, leading to higher charge-transfer resistance, stronger polarization, lower Li+ diffusivity, and higher nucleation overpotential. These factors collectively intensify early-stage heat generation. The study establishes a correlation between fluorination temperature and cathode structure, discharge-product evolution, discharge kinetics, and heat generation, demonstrating that regulating fluorination temperature is an effective strategy for improving the thermal safety of Li/CFx batteries.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60644-5
Lignin, as the sole renewable source of aromatic compounds, holds significant potential for producing green aviation fuel-range arenes via hydrodeoxygenation (HDO). In this study, a series of nitrogen-doped carbon-supported FeMoS/NC bimetallic catalysts were synthesized via a hydrothermal method. The HDO performance was evaluated using 4-ethylguaiacol as a model compound at 340 °C under 3 MPa H2. The unmodified MoS2/NC catalyst achieved a deoxygenation degree of 83.4%, whereas the Fe-modified catalyst with an optimal Fe/Mo molar ratio of 0.3 (Fe0.3MoS/NC) attained complete deoxygenation (100%) with an arenes selectivity of 78.6%. Beyond this optimal ratio, the deoxygenation degree inversely correlated with the Fe/Mo molar ratio. Characterization via XRD, TEM, BET, and XPS revealed that Fe incorporation enhanced the uniform dispersion of MoS2 on the NC support, increased surface acidity, and raised the concentration of sulfur vacancies, thereby promoting adsorption of oxygen-containing compounds. The HDO pathway over Fe0.3MoS/NC primarily proceeded via direct deoxygenation. When applied to real lignin under identical conditions (340 °C, 3 MPa H2, 12 h), the catalyst yielded 65.5% green hydrocarbons, with the C8–C16 fraction accounting for 54.4% of total hydrocarbons and an aromatic selectivity of 63.4% within this fraction. These results demonstrate that Fe0.3MoS/NC is a viable catalyst for selective conversion of lignin into green arenes suitable for sustainable aviation fuel applications.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010608
This study investigated the occurrence and distribution of 27 per- and polyfluoroalkyl substances (PFAS) in surface water and sediment of the Fuchun River, a tributary of the Qiantang River Basin. Surface water samples were analyzed using ultra-performance liquid chromatography coupled with high-resolution mass spectrometry. Total PFAS concentrations (∑PFAS) in surface water ranged from 30.04 to 105.26 ng/L, with mean and median values of 59.64 ng/L and 51.43 ng/L, respectively. The dominant compounds were perfluorooctanoic acid (PFOA), hexafluoropropylene oxide dimer acid (GenX), and perfluorobutanoic acid (PFBA). Concentrations generally decreased from upstream to downstream, consistent with previous studies. Notably, GenX levels were significantly elevated compared to earlier reports. In sediment, ∑PFAS concentrations ranged from not detected (ND) to 0.59 ng/g dry weight, with mean and median values of 0.14 ng/g and 0.11 ng/g, respectively. PFOA and perfluorooctanesulfonic acid (PFOS) were the primary sediment contaminants. Source apportionment indicated that industrial wastewater discharge and sewage treatment plant effluents were the main sources of PFAS in the river. Risk assessment using risk quotients suggested low ecological risks to aquatic organisms for most detected PFAS. However, the presence of short-chain and novel PFAS warrants further investigation due to potential unknown risks.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010607
This study investigated the occurrence, sources, and ecological risks of polycyclic aromatic hydrocarbons (PAHs) in soil, litter, and bark samples collected from the forest-grassland transition zone of Inner Mongolia. A total of 12 PAHs were detected in soil, with concentrations ranging from 34.9 to 465.3 ng·g⁻¹ (mean 168.8 ng·g⁻¹), predominantly 3–5 ring compounds. Litter contained 14 PAHs at concentrations between 106.4 and 2262.5 ng·g⁻¹ (mean 465.1 ng·g⁻¹), dominated by 3- and 4-ring PAHs. Both living and dead bark exhibited 14 PAHs, with concentration ranges of 119.2–240.0 ng·g⁻¹ and 123.3–241.6 ng·g⁻¹, respectively, mainly composed of 4-ring PAHs. Spearman correlation analysis revealed no significant correlations among PAH concentrations across the three media (P > 0.05). Source apportionment using diagnostic ratios and principal component analysis indicated that soil PAHs primarily originated from biomass, coal, and gasoline combustion; litter PAHs from petroleum volatilization and coal/natural gas combustion; and bark PAHs from petroleum volatilization and fossil fuel combustion, with high-molecular-weight PAHs dominating. Ecological risk assessment using the risk quotient (RQ) method showed that soil PAHs posed low overall ecological risk, though certain individual PAHs exhibited higher risk. The toxic equivalent (TEQ) method indicated that dead bark was the primary accumulation medium with high carcinogenic contribution, posing elevated ecological risk. Although litter and living bark had lower PAH concentrations, their long-term accumulation effects warrant attention. These findings provide crucial scientific evidence for understanding the environmental behavior and potential risks of PAHs in cold, high-latitude regions of northern China.
Environmental Chemistry•2026•DOI: 10.0000/202605-1
A method for the determination of hydrazoic acid and sodium azide in workplace air was established using ion chromatography with suppressed conductivity detection. Vapor and mist states of hydrazoic acid were collected in 40 mg·L−1 KOH absorption solution, while sol states of hydrazoic acid or sodium azide were collected on microporous membranes and eluted with 40 mg·L−1 KOH. Separation was performed on a Dionex IonPac™ AS11-HC (250 mm × 4.0 mm) anion analytical column with KOH gradient elution, followed by suppressed conductivity detection. The azide ion (N3−) exhibited good linearity in the range of 0.005–0.5 mg·L−1, with a correlation coefficient (r) of 0.9997. The limit of detection (S/N=3) was 0.002 mg·L−1, and the limit of quantification (S/N=10) was 0.005 mg·L−1. The minimum quantifiable concentrations in air were 0.00256 mg·m−3 for hydrazoic acid and 0.00387 mg·m−3 for sodium azide, based on a 10.0 mL sample solution and a 20 L air sample. Spiked recoveries ranged from 92.0% to 100.4%, with relative standard deviations (RSD, n=6) between 0.76% and 2.51%. The method is efficient, accurate, and sensitive, suitable for monitoring and safety assessment of hydrazoic acid and sodium azide in workplace air.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605014
Chlorinated aliphatic hydrocarbons (CAHs) are prevalent groundwater contaminants at industrial sites in China. This pilot-scale study evaluated in-situ anaerobic bioremediation of CAHs-contaminated groundwater in a low-permeability bedrock fracture zone at depths up to 40 m. A self-developed anaerobic dechlorinating culture (BS-1), containing Dehalococcoides, Desulfitobacterium, and Dehalogenimonas, was injected alongside carbon sources (sodium citrate and emulsified vegetable oil) and nutrients. Pressurized nitrogen gas injection enhanced the distribution of amendments, achieving a radius of influence of 5.0 m. Over 399 days of monitoring, the combined use of slow-release and soluble carbon sources maintained anaerobic conditions (ORP < -100 mV) for over one year, providing sustained electron donors. The emulsified vegetable oil reduced injection frequency and operational costs. The BS-1 culture effectively dechlorinated vinyl chloride, cis-1,2-dichloroethylene, trichloroethylene, and chloroform, achieving removal efficiencies exceeding 95%. At times, groundwater quality met the Class IV standard of GB/T 14848-2017. This study demonstrates a green, economical, and effective solution for CAH-contaminated site remediation, with significant engineering application potential.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225215
CO2 dilution is a recognized strategy for combustion control, yet its detailed effects on CH4/H2 combustion under lean conditions remain insufficiently characterized. This study numerically investigated jet diffusion flames in a triangular nozzle burner, varying CO2 mixing ratios from 0% to 40%, equivalence ratios from 0.4 to 0.9, at 300 K and 101325 Pa. The standard k-ε turbulence model and non-premixed combustion model were employed, with grid independence verified. Results showed that increasing CO2 blending reduced peak flame temperature, flame height, and average furnace temperature from 1688 K (0% CO2) to 1344 K (40% CO2). CO2 inhibited forward reactions of CO with O and OH, reducing O2 consumption. NOx emissions decreased by up to 95.5% at φ=0.7 (from 6.7×10-5 to 3.03×10-6) and 94.3% at φ=0.9, compared to pure methane. Conversely, H2 enrichment (0% to 40%) raised peak temperature from 2018 K to 2199 K and shifted the peak location closer to the burner (from 1.16 m to 0.82 m), promoting more compact flames. In CH4/H2 mixtures, CO2 still effectively reduced NOx, though the effect slightly weakened with higher CO2 ratios. Controlling CO2 blending below 30% balances NOx reduction and combustion stability. The CH4/H2/CO2 ternary strategy enables coordinated regulation of temperature and pollutant emissions, offering a technical pathway for hydrogen-rich fuel applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3850-3
Chiral nanomaterials have attracted considerable attention for antibacterial applications due to their unique chiroptical properties. Here, we report a novel spatiotemporally precise synergistic photodynamic therapy (PDT) and photothermal therapy (PTT) strategy using circularly polarized light (CPL)-activated chiral molybdenum-doped carbon dots (L-Mo-CDs and D-Mo-CDs). These chiral carbon dots were synthesized using chiral tartaric acid as a precursor. Notably, D-Mo-CDs selectively respond to left-handed CPL (LCP), while L-Mo-CDs respond to right-handed CPL (RCP). Under CPL irradiation, D-Mo-CDs exhibit enhanced reactive oxygen species (ROS) generation and a higher photothermal conversion efficiency (PCE) compared to L-Mo-CDs. In vitro antibacterial assays demonstrate that D-Mo-CDs possess excellent bactericidal efficacy against both Gram-positive and Gram-negative bacteria. In vivo wound healing studies in a mouse model reveal remarkable therapeutic efficacy, attributed to reduced inflammation, accelerated angiogenesis, and enhanced collagen deposition. This work introduces a paradigm for utilizing chiral carbon dots in precision antibacterial therapy, addressing the limitations of conventional chiral nanomaterials such as poor biocompatibility and low photothermal conversion. The findings underscore the potential of metal-doped chiral carbon dots for advanced biomedical applications, offering a spatiotemporally controllable approach to combat bacterial infections without promoting resistance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3897-6
Decoding the nature of catalytically active sites is an essential prerequisite for the rational design of catalysts for electrochemical H2O2 synthesis, but faces significant challenges, particularly for controversial cobalt single-atom catalysts (Co SACs). Herein, we report trace Co single-atom sites embedded within pyridinic N-rich carbon nanospheres (Co1-NNH3-C), synthesized via a self-assembly coupled surface-coating strategy. The Co1-NNH3-C catalyst demonstrates remarkable H2O2 selectivity (99%) and activity at current density of −3.5 mA cm−2 in 0.1 M H2SO4. Through a combined approach of molecular probe experiments, surface modification, and density functional theory (DFT) calculations, we disclose that pyridinic N, rather than Co single atoms, serves as the direct active site for 2e− oxygen reduction reaction (ORR). The trace Co (0.05 wt%) indirectly facilitated pyridinic N formation during pyrolysis but exhibits negligible direct catalytic involvement. DFT reveals pyridinic N sites optimize OOH intermediate adsorption (ΔG*OOH = 4.0 eV) and minimize reaction overpotential of 0.20 V, enabling scalable H2O2 production (907.5 mmol gcat−1 h−1). This work redefines the role of trace metal in SACs, providing a paradigm for designing metal-induced carbon catalysts for sustainable electrosynthesis for H2O2.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3834-x
Lithium metal anodes face critical barriers to practical application due to dendritic growth and interfacial instability, which cause short cycle life and safety hazards. This work introduces a highly stable and ultrahigh-rate lithium metal anode using a lithiophilic Sm2S3-modified carbonaceous host. The in situ formation of a Li2S-reinforced interphase layer enables highly reversible lithium plating/stripping and uniform deposition. The modified anode achieves an ultrahigh rate capability of 20 mA cm−2 and ultralong cycling stability of 7440 cycles with dendrite-free morphology. In a 4.5 V anode-less Li||LiCoO2 cell with an areal capacity of ~1.93 mA h cm−2, the system sustains over 1100 cycles with 87.2% capacity retention under harsh conditions: an ultralow negative-to-positive capacity ratio (N/P) of ~0.26 and lean electrolyte of ~5 g Ah−1. Furthermore, an anode-less pouch cell with an ultrahigh areal capacity of ~6.01 mA h cm−2 delivers superior cycling performance even at an ultra-low N/P ratio of ~0.71 and ultra-lean electrolyte of ~1 g Ah−1, achieving a high energy density of 505 Wh kg−1. This work provides a scalable and effective strategy for advancing reliable, practical lithium metal batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3814-2
Micro-structured surfaces have attracted increasing attention due to their great potential applications. However, it is still a challenge to continuously fabricate micro-structured surfaces based on thermoplastics by a facile, low-cost, and environmentally-friendly method. Herein, with the help of the extrusion molding method and an elaborately designed mold, micro-grooved fiber (MGF) based on high-density polyethylene (HDPE) is continuously prepared. Theoretically, infinitely long MGFs with feature sizes down to a few microns can be efficiently fabricated because of the continuous fabrication characteristic of the melt extrusion method. Interestingly, left- and right-handed micro-grooves with different helix angles can be produced by applying twisting at the die exit, and the macroscopically MGF springs can be further fabricated via a self-designed three-dimensional helical enwind device. By regulating wettability, MGF can achieve liquid self-transport on predefined paths. In addition, MGF fabric exhibits rapid evaporation behavior, whose evaporation rate is about 4 times higher than that of the Smooth fiber (SMF) fabric and 2 times higher than that of the most popular commercial quick-drying fabric (i.e., Cool-max fabric). This work proposes a facile and environmentally-friendly method for continuously preparing low-cost and flexible MGF, opening a new pathway to develop fiber-based microfluidic systems following the concept of "functionalized processing for thermoplastics".
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3933-9
The global cold chain consumes vast amounts of energy and emits greenhouse gases, while many regions lack proper refrigeration. To address this, we developed a dual-layer electrospun membrane (PZ-PML) for energy-free fruit preservation. The top PVDF-HFP/ZIF-8 layer offers 97.64% solar reflectance and 92.5% mid-infrared emissivity, providing 70 W/m2 radiative cooling. The bottom PAN/MIL-101/LiCl layer, with 2.18 g/g water uptake at 80% RH, delivers ~156 W/m2 evaporative cooling, lowering surface temperature by 6.1 °C under ~400 W/m2 irradiation. The membrane also shows ≥99% antibacterial efficiency against E. coli and S. aureus. Applied to strawberries, it reduced dehydration to 20.2% after 9 days, compared to 68.2% and 74.4% in controls. Additionally, it demonstrates durability, superhydrophobicity, and UV stability. This scalable solution offers energy-free fruit cooling, reducing postharvest losses while maintaining quality and safety.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3768-8
Damping materials are critical for mitigating vibrations and noise across various frequencies by converting mechanical energy into thermal energy. However, achieving a simultaneous high damping capacity and high toughness remains a formidable challenge. Here, we report a supramolecular polymer (SMP) that integrates high damping and toughness through the synergistic action of dynamic hydrogen bonds and side-chain relaxation. The polymer exhibits exceptional mechanical properties: a Young's modulus of 47.08 MPa, elongation at break of 605%, and toughness of 15.24 MJ m−3. The dynamic hydrogen bonds confer dual responsiveness to strain rate and temperature, with a 6.7-fold variation in Young's modulus under different stretching rates and a five-order-of-magnitude change in storage modulus across a temperature range. Under mechanical force, the interpenetrating side chains undergo mutual friction, enabling repetitive energy dissipation. This mechanism yields superior damping ability with a loss factor (tanδ) of 1.6 at 1 Hz, demonstrating outstanding performance in vibration absorption and noise reduction. The material's design offers a promising strategy for developing high-performance damping materials that balance energy dissipation and mechanical robustness, suitable for applications in wearable electronics, protective equipment, and structural vibration control.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509047
To reveal the dynamic characteristics of ecosystem carbon flux and its response to meteorological factors, this study employed the Biome-BGC model to simulate gross primary productivity (GPP) and net primary productivity (NPP) of vegetation in Beijing for historical (2001–2014) and future (2051–2070) periods under SSP126 and SSP585 scenarios, using multi-source data including regional meteorology, vegetation type, and soil texture. The Mann-Kendall (M-K) test and Empirical Orthogonal Function (EOF) analysis were applied to examine spatiotemporal patterns and carbon use efficiency (CUE). Results indicate that Biome-BGC accurately reproduces historical carbon flux characteristics. Temporally, annual mean GPP and NPP exhibited fluctuating upward trends, ranging from 584 to 777 g C m−2 a−1 and 238 to 388 g C m−2 a−1, respectively. Spatially, GPP and NPP displayed both same-phase and opposite-phase distribution patterns. Annual mean temperature was the dominant factor influencing GPP and NPP trends, followed by solar radiation and precipitation. Under future scenarios, both GPP and NPP are projected to increase, with SSP585 showing greater enhancement. By 2070, GPP is expected to rise by 171 and 376 g C m−2 a−1 under SSP126 and SSP585, respectively, while NPP increases by 71.8 and 137 g C m−2 a−1. The spatial distribution of GPP and NPP exhibits a 'low-center, high-periphery' pattern, with multi-year means of 969 and 425 g C m−2 a−1. Future CUE is approximately 0.45, indicating substantial carbon sequestration potential of Beijing's vegetation under climate change.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60618-9
Aromatic hydrocarbons, essential chemical feedstocks for fuels, synthetic fibers, and pharmaceuticals, are predominantly derived from petroleum refining. The catalytic conversion of lignin, a major lignocellulosic component, offers a renewable route to these chemicals. This review systematically examines the influence of pyrolysis methods, catalysts, and reaction conditions on the catalytic pyrolysis of lignin to aromatic hydrocarbons. Key parameters include catalyst acidity and pore structure, which govern selectivity and yield. Reaction temperature, catalyst-to-lignin ratio, and residence time critically affect product distribution. The review outlines catalytic mechanisms, such as deoxygenation, cracking, and aromatization, and highlights the role of zeolite catalysts, particularly HZSM-5, in enhancing monocyclic aromatic hydrocarbon yields. Metal modification (e.g., Fe, Ni, Ga) and pretreatment strategies (e.g., torrefaction) are discussed for improving efficiency. Challenges remain in catalyst deactivation due to coking and the complexity of lignin structure. Future research directions include developing robust catalysts, optimizing reactor designs, and integrating processes for industrial viability. This review provides theoretical and technological guidance for advancing lignin-to-aromatics conversion.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025021401
This study investigated the occurrence, distribution, sources, and ecological risks of 19 organophosphate triesters (OPEs) and 8 diesters (di-OPEs) in surface water and sediments from the Hangzhou section of the Qiantang River. Samples were analyzed using liquid chromatography-high resolution mass spectrometry. Concentrations of ΣOPEs in water ranged from 31.5 to 98.9 ng/L, and in sediments from 10.8 to 341 ng/g dry weight (dw). Σdi-OPEs ranged from 2.19 to 104 ng/L in water and 0.437 to 106 ng/g dw in sediments, indicating moderate to low contamination. TCIPP and TCEP dominated OPEs in water, while TEHP was the predominant OPE in sediments. DBP was the major di-OPE in water, and DPHP in sediments. Source apportionment via correlation and principal component analysis identified industrial production and human activities, including household, tire, plastic manufacturing, and agricultural practices, as primary sources. Ecological risk assessment revealed negligible risks for most OPEs in water, but notable risks in sediments: TEHP and EHDPP posed risks to crustaceans, and TPHP to algae. Moreover, combined toxicity at multiple sediment sampling sites raised concern, warranting further attention.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025030403
Microplastics (MPs) act as vectors for co-migrating antibiotics and heavy metals, forming complex pollution systems with potential joint toxicity. However, the differential adsorption behaviors and underlying mechanisms of MPs toward organic versus inorganic pollutants remain insufficiently understood. This study selected polypropylene (PP) microplastics, a major component of agricultural plastic films, and investigated the adsorption of sulfamethoxazole (SMX) and Cr(VI) onto aged PP under varying environmental conditions. Results demonstrated that aging increased the maximum adsorption capacity by 2–3 times for both pollutants. Notably, aged PP exhibited approximately 30 times higher adsorption capacity for SMX than for Cr(VI). Characterization revealed that aging introduced oxygen-containing functional groups (e.g., carbonyl) on the MP surface, enhancing adsorption. Mechanistic analysis indicated that hydrogen bonding and electrostatic interactions dominated SMX adsorption, while Cr(VI) adsorption was primarily governed by electrostatic interactions and pore-filling. The stronger intermolecular forces for SMX compared to reversible pore-filling for Cr(VI) explained the observed differences. Increasing pH induced electrostatic repulsion, reducing adsorption of both pollutants. High concentrations of Na+ and Mg2+ caused charge shielding, potentially enhancing Cr(VI) adsorption but inhibiting SMX adsorption due to competition for active sites. The presence of organic matter (humic acid) had negligible effects on Cr(VI) adsorption but reduced SMX adsorption, likely due to complexation. These findings elucidate distinct molecular-level pathways for organic versus inorganic pollutant adsorption on aged MPs, highlighting the roles of hydrogen bonding and pore-filling in driving differential behaviors.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025031001
The diffusive gradients in thin-films (DGT) technique has emerged as a promising tool for assessing the desorption kinetics and bioavailability of organic contaminants in soil. This study compared DGT, soil solution, and organic solvent extraction methods for evaluating the bioavailability of four sulfonamide antibiotics (SAs) in soil using pot experiments with Brassica rapa subsp. chinensis and Lactuca sativa. Results demonstrated that plant uptake of SAs depended on compound properties and plant species, with roots as the primary accumulation site. DGT-measured concentrations (CDGT) showed significant linear correlations with SA concentrations in both roots and leaves, and effective concentrations (CE) were positively correlated with plant tissue levels (P < 0.05). The soil solution method also showed predictive ability but with lower stability. The mass of SAs adsorbed by DGT increased non-linearly with deployment time, indicating that solid-phase resupply sustained long-term DGT uptake. DIFS model-derived soil-water partition coefficients (Kdl) ranged from 0.23 to 1.25 mL·g−1, with higher Kdl values corresponding to greater bioavailability. Response times (Tc) ranged from 2307 to 7523 seconds, with sulfamethoxazole (SMZ) exhibiting the highest Tc, indicating its release was most constrained. Meta-analysis of desorption parameters for other organic contaminants revealed that soil pH and particle size were key determinants of Kdl, while molecular volume and hydrophobicity influenced resupply rates. This study confirms the reliability of DGT for assessing antibiotic bioavailability in soil and provides fundamental data on their migration and fate.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025081103
Nitrous acid (HONO) is a critical precursor of hydroxyl radicals (·OH) in the atmosphere, influencing oxidative capacity and secondary pollutant formation. However, model simulations often underestimate HONO concentrations, and its role in nitrate formation remains unclear. This study investigates a typical winter haze episode in Guangzhou (January 2021, peak PM2.5: 243.0 μg·m−3) using observational data and a box model to quantify HONO sources and assess their impact on ·OH and particulate nitrate. HONO concentrations increased from (1.0±1.0) μg·m−3 during clean periods to (9.2±3.8) μg·m−3 during polluted periods, while nitrate rose from (6.4±3.4) to (43.3±20.0) μg·m−3 (6.8-fold). Incorporating seven additional HONO sources improved simulated daytime HONO from (0.3±0.1) to (6.5±2.3) μg·m−3, matching observations. Source apportionment showed direct vehicle emissions dominated (49.7%), followed by heterogeneous photosensitized reaction of NO2 on aerosol surfaces (23.0%), ground surface reaction (10.7%), and nitrate photolysis (8.7%). With optimized HONO, simulated daytime ·OH increased from (0.6±0.3)×10^6 to (1.5±0.8)×10^6 molec·cm−3 (1.2-fold), and nitrate production via ·OH+NO2 increased from (3.4±1.2) to (15.3±8.5) μg·m−3·h−1 (3.5-fold). The simulated-to-observed nitrate ratio improved from 21% to 81%. Sensitivity tests indicated that setting nitrate photolysis enhancement to 100 times gaseous nitric acid yielded better HONO and nitrate simulations. This study underscores the importance of refining HONO sources for accurate simulation of atmospheric oxidation and nitrate formation, aiding pollution control strategies.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025022704
Secondary inorganic aerosols (SNA), comprising sulfate, nitrate, and ammonium, are critical contributors to PM2.5 pollution in the Fenwei Plain, yet their formation mechanisms remain poorly characterized. Wintertime observations in Taiyuan revealed SNA as the dominant PM2.5 component, with a mean mass concentration of 33.19 ± 18.72 μg m−3, accounting for 47.13% of total PM2.5 mass. SNA concentrations increased markedly with pollution severity, but even under relatively clean conditions, SNA maintained a high mass fraction. Diurnal variation and correlation analyses indicated that nitrate formation pathways differed between day and night, largely governed by relative humidity (RH). During daytime, high RH (>55%) facilitated the partitioning of gaseous HNO3 to particulate nitrate. At night, RH positively correlated with nitrate concentration and nitrogen oxidation rate (NOR), with increased aerosol liquid water content (AWC) promoting NO2-to-nitrate conversion. The PM2.5 pH ranged from 4.3 to 5.2, and sulfate formation was primarily driven by H2O2 oxidation, with NO2 oxidation as a secondary pathway. These findings enhance understanding of SNA formation in the Fenwei Plain and provide a scientific basis for air quality policy.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606014
Microplastics, as emerging environmental pollutants, can adsorb psychotropic drugs in aquatic environments, facilitating their migration and transformation, ultimately posing ecological risks. This study investigated the adsorption behavior and mechanisms of four common microplastics—polyethylene (PE), polypropylene (PP), polystyrene (PS), and polyvinyl chloride (PVC)—each with a particle size of 50 μm, toward three psychoactive drugs: diazepam, fluoxetine, and mianserin. Adsorption kinetics, isotherms, and the effects of pH and salinity were examined. Kinetic data fitted well to a pseudo-second-order model, indicating chemisorption as the rate-limiting step. Isotherm analysis using Langmuir and Freundlich models revealed that PE exhibited the highest affinity for fluoxetine, PP for mianserin, and PVC for diazepam, while PS showed linear adsorption for fluoxetine, suggesting partitioning. The adsorption of diazepam was maximal at pH 6.5–8.5, typical of natural surface waters, and increased with NaCl concentration, indicating that non-electrostatic interactions dominate and that higher ionic strength enhances adsorption. Mechanistic insights suggest that hydrophobic interactions, hydrogen bonding, π-π interactions (for PS), and halogen bonding (for fluoxetine) contribute to adsorption. These findings highlight the potential of microplastics to act as vectors for psychoactive drugs, necessitating further research on their environmental fate and ecological implications.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606004
To identify optimal watershed remediation pathways under environmental and economic dimensions, an integrated environmental-economic impact assessment framework combining life cycle assessment (LCA) and life cycle costing (LCC) based on openLCA was established, using 1 m³ of treated wastewater as the functional unit. This framework comprehensively evaluated the environmental impacts and economic costs of three ecological buffer measures—constructed wetlands, ecological intercepting ditches, and vegetation restoration projects—in non-point source pollution control. The results indicated that constructed wetlands offer the optimal environmental-economic profile, featuring the lowest comprehensive cost (¥1.01 yuan/m³) and the lowest load across most environmental impact categories, with only slightly higher land resource consumption intensity. Ecological intercepting ditches exhibited higher impacts in areas such as metal resource consumption due to the use of rebars and base fertilizer inputs, resulting in a moderate comprehensive cost (¥1.57 yuan/m³). Vegetation restoration projects incurred the highest comprehensive cost (¥61.14 yuan/m³) and produced the most significant environmental impacts, with elevated indicators such as human carcinogenic toxicity. This primarily stemmed from the extensive use of concrete grass pavers and base fertilizer in rural river sections. These findings provide quantitative references for environmental-economic integrated evaluation and decision-making regarding ecological buffer zone engineering schemes in similar watersheds.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606015
This study evaluated the sustainability and tissue-specific mechanisms of corn stover as a solid-phase carbon source for nitrate removal from groundwater. Cyclic heterotrophic denitrification experiments were conducted using leaf, stem pith, stem bark, stem node, husk, and mixed tissues as carbon sources. Denitrification efficiency, sustainability, dissolved organic carbon (DOC) release, carbon utilization efficiency, intermediate accumulation, and environmental parameters were systematically assessed. Kinetic modeling, correlation analysis, and structural equation modeling (SEM) were applied to elucidate regulatory mechanisms. Results demonstrated that mixed tissues and husk achieved the highest denitrification efficiency, with nitrate removal rates consistently above 98% across four repeated cycles. Total nitrogen removal reached 39.30 mg/g for mixed tissues and 39.95 mg/g for husk, while byproduct concentrations (NO2-N and NH4-N) remained below 2 mg/L. DOC release profiles indicated stable carbon release and high carbon utilization efficiency (203.99 mg TN/g organic carbon for mixed tissues; 182.41 mg/g for husk). Correlation and SEM analyses revealed that carbon source type indirectly governed total nitrogen removal by modulating DOC release, which subsequently influenced pH, electrical conductivity, and nitrogen transformation pathways. Significant differences among tissues were observed in denitrification efficiency, carbon utilization, and micro-environmental regulation. Mixed tissues and husk emerged as superior carbon sources due to their combined efficiency and stability. However, husk released odorous compounds during operation, posing sensory challenges for practical application. The findings support the potential of corn stover tissues as cost-effective carbon sources for in-situ groundwater nitrate remediation, though further optimization is required for field-scale implementation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3986-2
Organic/molecular ferroelectrics exhibiting spontaneous polarization have attracted increasing attention due to their flexibility, light weight, low-temperature processability, environmental friendliness, and biocompatibility. Among them, organic donor-acceptor cocrystals, self-assembled from two or more components, offer new insights into ferroelectricity. This review systematically examines recent progress in organic donor-acceptor cocrystal ferroelectrics, focusing on microscopic origins of ferroelectricity, structure modulation strategies, and underlying mechanisms. Ferroelectric origin mechanisms, including intermolecular charge transfer, proton transfer, and order-disorder transitions, are analyzed in detail. Structure-property relationships in crystal engineering are summarized, and recent advances in theoretical simulations, experimental characterization techniques, and practical applications are introduced. Finally, current challenges and future research perspectives are outlined. The review highlights that weak intermolecular interactions often lead to low Curie temperatures (Tc), limiting practical applications. Strategies to enhance Tc involve introducing stronger molecular interactions to increase transition energy barriers. Notably, room-temperature ferroelectricity in organic cocrystals has been achieved, as demonstrated by Wiscons et al. (Angew Chem Int Ed, 2018, 57: 9044–9047). The review underscores the potential of organic cocrystal ferroelectrics for flexible and wearable electronics, while addressing the need for higher Tc and robust switching performance.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606016
Barium slag, a solid waste from barium salt production, poses environmental risks due to high sulfur and soluble barium content. This study investigated the desulfurization of barium slag using sodium carbonate (Na2CO3) as a precipitating agent. The effects of reaction temperature, time, and Na2CO3 concentration on desulfurization efficiency were systematically evaluated. X-ray diffraction (XRD) and scanning electron microscopy with energy-dispersive spectroscopy (SEM-EDS) were employed to analyze phase transformations and microstructural evolution. Results showed that desulfurization primarily proceeds via the reaction of ettringite (Ca6(Al(OH)6)2(SO4)3·26H2O) with Na2CO3, forming calcium carbonate (CaCO3) precipitates. However, the precipitated CaCO3 accumulates on ettringite surfaces, hindering further reaction. Under optimal conditions (60 °C, 5 h, 2 mol/L Na2CO3), the desulfurization efficiency reached 91.21%, reducing sulfur content in the slag to 0.27%, meeting the HJ 662—2013 standard for cement kiln co-processing. This work provides a mechanistic basis for efficient and environmentally sound treatment of barium slag, supporting its resource utilization in cement production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3864-4
Organic room temperature phosphorescence (RTP) materials, particularly those emitting in the near-infrared (NIR) region, hold great promise for bioimaging due to their deep-tissue penetration and minimal autofluorescence interference. However, achieving efficient NIR RTP with long lifetimes remains challenging due to inefficient triplet exciton utilization. Herein, we propose a dark triplet state activation strategy to achieve efficient NIR RTP by leveraging host–guest energy transfer. Using benzophenone derivatives (BP, OBP, MBP, PBP) as rigid host matrices with high intersystem crossing (ISC) efficiency and an NIR fluorophore (MPTCF) as the guest, we achieve efficient Dexter-type triplet-triplet energy transfer (TTET) that converts non-emissive host triplets into guest-centered NIR phosphorescence. Systematic optimization of the host–guest system has shown that PBP/MPTCF exhibits exceptional performance, including long phosphorescence centered at 705 nm, an ultralong phosphorescence lifetime (210.3 ms), and high ISC efficiency (44.4%). When fabricated into nanoparticles (NPs), PBP/MPTCF exhibits superior performance, featuring prolonged phosphorescence signals (>120 s), deep tissue penetration capability (>2 mm), and excellent biocompatibility (cell viability >95% at 300 μM). In addition, this system enables high-contrast subcutaneous imaging with excellent dispersibility and stable in vivo imaging capability. More importantly, PBP/MPTCF NPs demonstrate precise lymph node mapping through time-gated phosphorescence imaging and efficient tumor visualization within 4 h post-injection with a high tumor-to-liver ratio of 2.8. The successful activation of dark triplet states through this host–guest approach provides a general design principle for developing high-performance NIR RTP materials, while the demonstrated biomedical applications highlight their significant potential for advanced bioimaging and precision diagnostics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3889-6
Photocatalytic hydrogen production is fundamentally limited by inefficient charge separation and asynchronous supply of electrons and protons to active sites. Here, we designed a ZnIn2S4/ZnCo2S4 (ZIS/ZCS) heterojunction with an atomically coherent interface achieved via an ultralow lattice mismatch of 0.05%. This unique structure promotes rapid electron transfer through a built-in electric field and facilitates continuous proton migration via a hydrogen spillover effect, thereby synchronizing electron and proton delivery at the catalytic interface. This dual regulation of electrons and protons synergistically promotes proton-coupled electron transfer, resulting in a high hydrogen evolution rate of 70.3 mmol g−1 h−1 and selective oxidation of benzyl alcohol to aldehyde (39.3 mmol g−1 h−1) with 93.6% selectivity. This work demonstrates the critical importance of lattice match and dual charge-proton management in designing efficient photocatalysts for complex redox reactions.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3790-5
Near-infrared (NIR) phosphors with high quantum efficiency (QE) and thermal robustness are critical for phosphor-converted light-emitting diodes (pc-LEDs). Here, a Cr3+-activated Lu2BaAl4SiO12 (LBASO) garnet phosphor is engineered via chemical unit cosubstitution of [Ba2+-Si4+] for [Lu3+-Al3+] in Lu3Al5O12 (LuAG), inducing a strong crystal field that yields NIR emission at 705 nm. The optimized LBASO:0.07Cr3+ exhibits an internal quantum efficiency (IQE) of 84.82% and external quantum efficiency (EQE) of 46.02%. Notably, it demonstrates anti-thermal quenching (ATQ) with 126.03% of its initial intensity at 498 K under 442 nm excitation, attributed to a wide band gap, weak electron-phonon coupling, defect trap energy levels, high structural rigidity, and optimized electron population distribution. A NIR pc-LED fabricated with this phosphor achieves an output power of 134.99 mW and photoelectric conversion efficiency of 11.4% at 100 mA drive current. These results underscore the potential of LBASO:Cr3+ for applications in plant lighting, night vision, and nondestructive analysis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3890-6
Photothermal catalysis offers a sustainable route for CO2 conversion to value-added chemicals, yet precise control of active sites and light-harvesting materials remains challenging. Here, we report the rational integration of three-dimensional ordered macroporous (3DOM) CeO2 with positively charged (Niδ+)n clusters to construct efficient photothermal catalysts for the reverse water gas shift (RWGS) reaction. The 3DOM architecture enhances light absorption, improves access to active sites, and provides a confined environment for reactant enrichment. Engineering (Niδ+)n clusters within 3DOM CeO2 not only affords highly active sites for H2 adsorption and dissociation but also modulates the local structure of CeO2 to promote CO2 adsorption and activation. Furthermore, the (Niδ+)n clusters significantly enhance light-harvesting capability across the UV-vis-NIR spectrum, generating a pronounced photothermal effect that accelerates reaction kinetics. The optimized (Niδ+)n/CeO2 catalyst exhibits outstanding photothermal catalytic performance, achieving a CO production rate of 63.36 mmol g−1 h−1 in a flowing reaction with CO selectivity of 93% under simulated solar irradiation (2.6 W cm−2). Theoretical calculations reveal that the (Niδ+)n/CeO2 catalyst reduces the thermodynamic energy barrier for *COOH formation in CO2 hydrogenation. This study offers valuable insights into the design of photothermal catalysts, highlighting the significant potential of active-site engineering in promoting efficient CO2 conversion for practical solar-to-fuel production.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60653-6
Carbon deposition caused by mass transfer limitations is a key challenge for traditional microporous ZSM-5 zeolites in coal tar catalytic cracking. To address this, benzene was used as a model compound. Parent ZSM-5 (NL-ZSM-5) was modified with tetraethylammonium hydroxide (TEAOH) to prepare hierarchical ZSM-5 zeolites with different mesopore sizes. Characterization (XRD, FT-IR, BET, TEM) confirmed successful mesopore introduction via selective desilication while retaining the MFI structure. At TEAOH concentration of 0.4 mol/L (ZSM-5-C), total pore volume increased from 0.24 to 0.43 cm3/g, and Brønsted acid amount increased from 0.28 to 0.67 mmol/g, with improved acid site accessibility. Catalytic experiments and carbon deposition analysis showed that hierarchical pore structure inhibits coking via a synergistic effect of diffusion enhancement and adsorption-site regulation. The coke amount of ZSM-5-C was 4.0%, only one-third of that of NL-ZSM-5 (11.9%). Molecular dynamics simulations confirmed that the diffusion coefficient of benzene in a 3.0 nm mesopore model is an order of magnitude higher than in a 2.0 nm model. Adsorption capacity decreases with increasing mesopore size, shortening residence time. Increasing temperature enhances diffusion but exponentially intensifies surface condensation reactions (Arrhenius effect), which dominates coke formation; hierarchical pores mitigate this negative effect. This research provides a theoretical basis for designing high-efficiency, coke-resistant catalysts for coal tar conversion.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60659-7
Coal gasification fine slag (CGFS), a solid waste from entrained-flow coal gasification, is characterized by fine particles and high silicon and aluminum content. This study proposes a simple and economical hydrothermal synthesis of ZSM-5 molecular sieve using CGFS as raw material. Impurities were removed by acid washing, followed by alkaline extraction of silicon and aluminum species. The extracted Si-Al precursors were crystallized hydrothermally at 170 °C for 48 h, yielding ZSM-5 with a high specific surface area of 358 m2/g. Adsorption experiments showed that the synthesized ZSM-5 exhibited excellent Pb2+ removal performance: at 25 °C, the removal efficiency for a 50 mg/L Pb2+ solution reached 83.7%, with an adsorption capacity of 104.625 mg/g under optimized conditions. The adsorption process is mainly governed by chemisorption mechanisms, including surface complexation, precipitation, and ion exchange. Thermodynamic analyses indicated that Pb2+ adsorption is spontaneous and endothermic, consistent with multilayer chemisorption. The synthesized ZSM-5 shows promising potential for application in the treatment of lead-containing wastewater, offering a high-value utilization route for coal-based solid waste.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026020207
Although the production and use of hexabromocyclododecanes (HBCDs) have been completely banned in China since December 2021, historical production activities may still leave high-concentration residual contamination in localized areas. This study investigated a typical legacy site of historical HBCDs production in eastern China. Surface and core soil samples were systematically collected both inside and outside the former plant area to characterize the occurrence, spatial distribution, and environmental burden of HBCDs, and to evaluate associated human health risks. Results showed that HBCD concentrations in soils outside the plant area ranged from below detection limit to 6.90×10² ng·g⁻¹ dw, while those inside the plant area were substantially higher, reaching up to 1.18×10⁶ ng·g⁻¹ dw. γ-HBCD was the dominant isomer; however, its relative abundance was lower than that reported in commercial HBCD mixtures and in previous studies conducted near production facilities. Outside the plant, HBCDs concentrations in soil generally decreased with increasing distance from the site, yet remained detectable at a distance of approximately 10 km (15.2 ng·g⁻¹ dw). Within the plant area, HBCDs concentrations in soil cores decreased with depth, declining from 1.08×10⁴–1.18×10⁶ ng·g⁻¹ dw in surface soils to 1.05–93.5 ng·g⁻¹ dw at depths of about 4 m. Analysis of the relative cumulative environmental burden indicated that although HBCDs loads were highest in the near-source area, they gradually accumulated over a broader spatial scale. Approximately 23.7%, 40.1%, 60.0%, and 87.1% of the total estimated burden accumulated within 2 km, 2.81 km, 4 km, and 6 km from the site, respectively. Health risk assessment indicated that oral ingestion of soil was the primary exposure pathway for different populations. Localized high-contamination zones within the plant area contributed significantly to non-carcinogenic risks, while overall risks for children outside the plant area were at acceptable levels.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025102801
This study develops a multivariate time-series forecasting model for water quality in the Lhasa River, focusing on four key indicators: water temperature, pH, dissolved oxygen, and turbidity. Data preprocessing integrated multiple missing-value imputation strategies and interquartile range (IQR) outlier removal. Boxplots and relative standard deviation (RSD) assessed data distribution and dispersion, while autocorrelation and Pearson correlation analyses revealed periodic patterns and inter-variable relationships. Four representative algorithms—Support Vector Regression (SVR), Extreme Gradient Boosting (XGBoost), CNN-BiLSTM-Attention, and TCN-Transformer—were optimized via Bayesian hyperparameter tuning. Model performance was evaluated using MAE, MSE, RMSE, and R². The study systematically compared the effects of different missing-value handling methods, both independently and combined with IQR outlier removal. Results indicate that CNN-BiLSTM-Attention excels in water temperature prediction, suitable for relatively stable and simple patterns. In contrast, TCN-Transformer demonstrates superior performance for pH, dissolved oxygen, and turbidity, which exhibit strong nonlinearity and long-term dependencies, effectively capturing temporal dependencies and coupling relationships. The findings provide a viable technical route and theoretical reference for river water quality monitoring and intelligent early-warning systems.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026022502
This study investigates the effects of different land use types on topsoil carbon (C) and nitrogen (N) contents and their spatial distribution in the lower reaches of the Sancha River Basin, a karst region of the Yunnan-Guizhou Plateau. Grid sampling collected 0–20 cm topsoil from forestland (n=23), cultivated land (n=25), and grassland (n=32). Total C and N were measured. Results showed that topsoil C content followed grassland (40.36±22.92 g·kg−1) > forestland (37.05±12.83 g·kg−1) > cultivated land (34.06±14.57 g·kg−1), while N content followed forestland (2.89±0.76 g·kg−1) > grassland (2.67±1.19 g·kg−1) > cultivated land (2.50±0.65 g·kg−1). One-way ANOVA revealed no significant differences among land use types (P>0.05). Soil C and N were significantly positively correlated across all land uses (r>0.5, P<0.001). Coefficient of variation (CV) indicated grassland had the highest C variability (0.57), while forestland showed the most stable C and N (CV=0.35 and 0.26, respectively). Cultivated land had CVs of 0.43 for C and 0.26 for N. Spatially, forestland exhibited concentrated high C values with significant N heterogeneity; grassland had higher C in southern and eastern areas but scattered distribution, with generally low and variable N; cultivated land showed uniform but lowest C and N. Land use types significantly drive topsoil C and N dynamics through vegetation input, soil disturbance, and management practices, underscoring the importance of rational land use planning for enhancing carbon sink functions and sustainable development in karst watersheds.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025040401
Conventional zero-valent iron (ZVI) suffers from limited electron transfer due to its dense surface oxide layer. This study introduces a mechanochemical ball-milling strategy incorporating sodium chloride (NaCl) with ZVI to fabricate chloride-modified ZVI (Cl-ZVIbm). Using hexavalent chromium (Cr(VI)) as a model pollutant, Cl-ZVIbm exhibited a 76.5-fold enhancement in removal kinetics (0.0306 min−1 vs. 0.0004 min−1) compared to ball-milled ZVI (ZVIbm), achieving complete removal of 2 mg·L−1 Cr(VI) within 120 min. Spectroscopic characterization and density functional theory (DFT) calculations revealed dual regulation mechanisms: (1) Cl− substitution of surface hydroxyl groups alters coordination environments, enabling Cr(VI) adsorption via a bidentate binuclear configuration with adsorption energy reduced from –0.28 eV to –1.64 eV; (2) The strong electron-withdrawing effect of Cl− drives directional electron migration from the iron core to the surface, increasing surface Fe(II) content by 26.9% (67.5% vs. 53.2%) and facilitating direct electron transfer to reduce 99.5% of Cr(VI) into low-toxicity Cr(III). Notably, chloride leaching during reactions was only 0.0126 mmol·L−1, far below industrial wastewater discharge standards, confirming environmental compatibility. This work provides atomic-scale insights into chloride-mediated electronic modulation on ZVI surfaces, offering novel principles for interfacial engineering of environmental functional materials and a theoretical basis for heavy metal remediation technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3965-5
Liquid crystal elastomers (LCEs) have emerged as a promising material platform for soft robotics, effectively integrating programmable molecular orientation with the inherent flexibility of elastomers. This unique combination enables significant, reversible deformations responding to external stimuli, including heat, light, electric, and magnetic fields. Due to these characteristics, LCEs serve as an ideal material system for bridging biological principles with engineered soft robotic applications, enabling the development of adaptive and multifunctional systems with enhanced biomimetic capabilities. However, the mechanisms of bioinspired motion and the effective integration of biomimetic functions in LCE-based robots remain insufficiently explored. This review systematically examines recent advances in LCE-based biomimetic soft robots, focusing on multimodal actuation strategies, including contraction, crawling, rolling, jumping, swimming, and plant-inspired motions. It highlights integrated functional enhancements achieved via innovative material compositions, structural designs, and advanced manufacturing techniques. These developments have enabled novel robotic functionalities, including programmable actuation, self-healing and recycling, color morphing and camouflage, and tunable bioinspired surface characteristics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3875-1
Photocatalytic hydrogen evolution reaction (HER) from pure water is a promising strategy to address critical challenges in energy sustainability and environmental remediation. However, HER over single-component photocatalysts is intrinsically limited by inefficient carrier separation and relatively poor photostability. Forming abundant interfaces between two components is an effective approach for solving these issues. Herein, a series of hierarchical core-shell heterojunction photocatalysts, designated as F@Z-X, was rationally constructed by in situ growing ZnIn2S4 (ZIS) nanosheets on a Ti-based metal-organic framework (FIR-125), demonstrating remarkable structural stability. Due to the abundant intimate contact interfaces and well-matched band structure, the F@Z-X series exhibit enhanced HER performance. Among them, the optimized heterojunction [email protected] shows a photocatalytic hydrogen evolution rate of 3789.45 μmol g−1 h−1, which is about 4.4 and 264.4 times higher than that of pristine ZIS (859.57 μmol g−1 h−1) and FIR-125 (15.32 μmol g−1 h−1), respectively. Moreover, the photocatalyst manifests excellent reusability and durability, maintaining its performance over five consecutive cycles and sixteen hours of continuous reaction. The outstanding performance of [email protected] may be ascribed to an optimal balance among three fundamental photocatalytic processes: sufficient light absorption, exceptional carrier separation, and appropriate surface reaction. This work offers valuable insights into the rational design and controllable synthesis of novel heterojunction photocatalysts for efficient hydrogen evolution.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3920-1
Lead-free halide perovskites are promising scintillators due to strong X-ray attenuation and high internal quantum efficiency (IQE), but their application is hindered by moisture sensitivity. Here, CsSrCl3:Eu2+ nanocrystals were grown in situ in a specially designed inorganic glass matrix. By employing [PO4]-modification and controlled crystallization, a transparent CsSrCl3:Eu2+ glass-ceramic (GC) scintillator was obtained, combining high crystallinity (15.9%) with excellent optical transparency (85.3% at 432 nm). The GC exhibits outstanding photoluminescence (PL) performance, including a high IQE of 87.6% and superior thermal stability (74% intensity retention at 493 K relative to 303 K). Benefiting from the robust glass matrix, the GC retains 99% of its initial PL intensity after 14 days of water immersion. Under X-ray excitation, it shows blue X-ray excited luminescence (XEL), with peak and integrated intensities reaching 117% and 25.1% of those of Bi4Ge3O12 crystal, respectively. The scintillator achieves a high spatial resolution of 20 lp mm−1 and an X-ray detection limit of 3.7 μGy s−1. Furthermore, it demonstrates exceptional operational stability in humid environments, maintaining clear X-ray image contrast even after 48 h of water submersion. This study provides an effective strategy for stabilizing hygroscopic halide scintillators in a durable [PO4]-modified fluoroaluminate glass matrix and demonstrates the potential of CsSrCl3:Eu2+ GC for high-resolution and stable X-ray imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3948-7
High-performance thermoelectric materials are typically narrow-band gap semiconductors. Here, by decoupling charge and heat transport in BaZrS3 with a band gap of about 1.9 eV, we made the emerging chalcogenide perovskite a high-performance thermoelectric material with only earth-abundant elements. Our first-principles calculations indicate that the high ionicity of BaZrS3 renders the electrons to propagate mainly through the Zr-4d orbitals, so that isovalent alloying Se on S sites minimally affects its charge transport while effectively suppressing lattice thermal conductivity. Using a flux-assisted solid-state method, we synthesized single-phase BaZrS3(1−x)Se3x samples with 0 ≤ x ≤ 0.25. As an indicator of decoupled charge and heat transport, the electron mobility is found barely degraded with increasing Se content, while the thermal conductivity is significantly reduced from 2.07 to 0.99 W m−1 K−1 at room temperature. This results in a record-high ZT of 0.81 at 750 K, a value never achieved for materials with band gaps greater than 1.5 eV, and the highest among all perovskite materials. Our work not only underscores the potential of wide band gap semiconductors as high-performance thermoelectric materials, but also demonstrates the strategy of decoupling the charge and heat transport for enhancing their thermoelectric performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3979-3
The escalating prevalence of multidrug-resistant Pseudomonas aeruginosa (P. aeruginosa) infections necessitates novel antibacterial strategies. Here, we engineered lectin B (LecB)-targeted glyco-dots (TFP2F) via self-assembly of a photosensitizer (TFP2) possessing aggregation-induced reactive oxygen species (ROS) generation capability with fucose-modified tetraphenylethene glycoclusters (TPE-Fuc4), enabling P. aeruginosa-targeted antimicrobial photodynamic therapy and wound healing promotion. Three photosensitizers (TFP0–2) featuring an “A-D-A” electronic structure were synthesized, exhibiting broad absorption bands and near-infrared (NIR) fluorescence. Among these, TFP2 demonstrated superior Type-I/II ROS production (including ·OH, ·O2−, and 1O2), achieving potent phototoxicity against P. aeruginosa (MIC80 = 7.5 μM). Self-assembly with TPE-Fuc4 yielded glyco-dots TFP2F that facilitated LecB-mediated bacterial targeting, enhanced bacterial uptake, and significantly reduced the MIC80 to 2.5 μM against drug-resistant P. aeruginosa under light irradiation. In a murine P. aeruginosa-infected wound model, TFP2F treatment combined with light irradiation accelerated wound closure to <20% of the initial area by day 8 (vs. >40% in controls) and eliminated >95% of bacteria by day 2. This work presents a convenient strategy for constructing glyco-dots as a potent functionalized platform for precision, lectin-targeted antimicrobial photodynamic therapy.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508006
Landfill leachate, characterized by high ammonia nitrogen, high organic load, complex toxic components, and low nitrogen removal efficiency, poses significant environmental challenges. To achieve efficient nitrogen removal, a continuous-flow two-stage anoxic/oxic (A/O) moving-bed biofilm reactor (MBBR) system coupled with anaerobic ammonium oxidation (Anammox) was constructed and operated for long-term treatment of actual landfill leachate. After biofilm attachment and multi-gradient acclimation, influent concentrations were gradually increased from low levels (NH4+-N ~200 mg·L−1, COD ~2500–3000 mg·L−1) to high levels (NH4+-N ~1800 mg·L−1, COD ~8500 mg·L−1). During stable operation, average removal efficiencies of NH4+-N and COD reached 97.7% and 66.8%, respectively, with total nitrogen (TN) removal efficiency improving to 93.9%. Along the reactor, the first A/O stage achieved major organic degradation and ammonia oxidation, while the second stage facilitated nitrite accumulation and promoted Anammox for synergistic nitrogen removal. High-throughput sequencing revealed Proteobacteria as the dominant phylum (>50%), with denitrifying genera such as Azoarcus and Thauera significantly enriched. Planctomycetota abundance increased from 0.6% to 3.7%, and Candidatus Kuenenia was detected, confirming successful Anammox colonization and participation in nitrogen removal. This study validates the efficient combined nitrogen removal mechanism of the A/O–MBBR system with Anammox, providing theoretical basis and technical support for engineering treatment of high-ammonia wastewater.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511043
Zero-valent iron (ZVI) suffers from surface passivation and low electron utilization in reductive removal of nitrobenzene (NB). To address these issues, a ball-milled iron/digestate biochar composite (BM-Fe/DBC) was prepared and compared with a physically mixed counterpart (PM-Fe/DBC). Characterization revealed that ball milling tightly embedded ZVI particles into the carbon matrix, forming Fe–C chemical bonds and a strong interfacial coupling structure that established efficient electron transfer channels. This structure significantly enhanced the micro-galvanic effect between iron and carbon, yielding superior reduction performance across a wide pH range (3–9). Under optimal conditions (Fe:C mass ratio 2:1, dosage 1.0 g·L−1, pH 5), BM-Fe/DBC achieved 79.9% NB removal, and the generation of aniline (AN) was 1.85 times that of PM-Fe/DBC. Mechanistic studies indicated that the intimate Fe–C interfacial coupling promoted sustained ZVI corrosion and enhanced the production of indirect reducing species, including adsorbed Fe(II) and atomic hydrogen (H*). Electrochemical analyses showed that BM-Fe/DBC exhibited a lower corrosion potential, a higher corrosion current density (approximately 2.15 times higher), and lower charge transfer resistance, kinetically confirming its superior electron transfer capability. These findings reveal that constructing strong interfacial coupling in iron–carbon composites via mechanochemical methods can effectively overcome key limitations of ZVI in reduction reactions, providing a theoretical basis and practical pathway for designing high-performance water treatment materials.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60676-7
Landfilled municipal solid waste (MSW) in China exceeds 8 billion tons, with high moisture (30–50%) and ash content (>50%), complicating conventional treatment. Slag gasification offers a clean and resource-oriented route, but heavy metal leaching from the resulting slag poses environmental risks. This study investigates the effect of rice husk addition (5–15%) on the vitrification of landfilled-waste slag and the immobilization of heavy metals (Cr, Zn, Cu). Results show that adding 5–10% rice husk lowers the slag flow temperature to a minimum of 1213 °C, attributed to active SiO2 reacting with CaO and Fe2O3 to form low-melting eutectics like anorthite. Leaching concentrations of Cr and Zn decrease from 41.60 and 108.00 mg/L to 5.89 and 7.10 mg/L, respectively, with 10–15% rice husk. The amorphous SiO2 enhances silicate polymerization (Q3, Q4 networks), promoting physical encapsulation and chemical incorporation of heavy metals into stable phases such as Zn2SiO4 and CuFe2O4, increasing the residual fraction and reducing bioavailability. At temperatures >1400 °C, volatilization of Cu and Zn increases, with residual rates dropping to 33–60% and 31–55%, respectively, while Cr remains stable (70–123%). This work elucidates the mechanistic role of rice husk in slag structure modulation and heavy metal immobilization, providing a theoretical basis for the co-treatment of landfilled waste and biomass via a 'treating waste with waste' strategy.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60657-3
Fe-Mn catalysts have attracted considerable attention for industrial Fischer-Tropsch synthesis (FTS) due to their ability to modulate product spectra. Carbon adsorption and permeation on catalyst surfaces are critical elementary steps in the in situ formation of active iron carbide phases. Here, density functional theory (DFT) calculations systematically investigate the atomistic structures, thermodynamic stabilities, and electronic properties of carbon-deposited Fe-Mn alloy surfaces at the early stage of carburization. These surfaces exhibit distinct thermodynamic sensitivity to carbon atoms adsorbed on the surface and permeating into interstitial sites. By combining DFT with minima-hopping structural searches, we demonstrate that the initial stage of carbon permeation cannot trigger surface reconstruction to form iron carbide phases. The addition of manganese thermodynamically hinders carbon permeation. Although deposited carbon atoms modulate the electronic structure of metals, manganese retards the shift of d-band centers toward those of bulk iron carbide phases. This study provides atomic-scale insight into the in situ evolution of Fe-Mn catalyst surfaces during carbon deposition, indicating that manganese promoter has a noticeable effect on carbon permeation.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60710-4
Lignin pyrolysis is a promising route for sustainable production of high-value phenolic chemicals, yet the intricate radical reaction network remains a major bottleneck to optimizing product selectivity. This work constructs a standardized DFT computational database that systematically describes the fast pyrolysis of vanillyl alcohol at 823.15 K. The database features three key components: primary reaction pathways, thermodynamic energy barriers, and atomic-level electronic fingerprints. The dataset covers primary reaction pathways, secondary rearrangements, and both global and local reactivity indices of key intermediates. Notably, it innovatively integrates electronic-structure fingerprints, filling the gap in reaction-network–electronic-property correlation data. Standardized computational workflows and rigorous quality control ensure accuracy, consistency, and reproducibility. The public release of this dataset provides a reliable theoretical benchmark for mechanistic studies of lignin pyrolysis and offers foundational data support for rational design of new catalysts and refinement of reaction kinetic models. Ultimately, this database not only provides an important reference for data-driven catalyst development but also lays a theoretical foundation for precise regulation of lignin depolymerization.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042304
To characterize the spatial variability of PM2.5 chemical components at the urban scale, ambient PM2.5 samples were collected from eight sites across Changsha, China. Samples were analyzed using ion chromatography, elemental carbon/organic carbon (EC/OC) analysis, and X-ray fluorescence (XRF) spectroscopy. Results showed that PM2.5 concentrations in urban areas were significantly higher than in suburban locations, with notably elevated levels at Changsha New Railway Station and Mapoling. Across different PM2.5 pollution levels, the eight sites exhibited pronounced spatial differences in concentration while sharing similar chemical compositions. Source apportionment identified secondary nitrate, vehicle emissions, and secondary sulfate as major contributors to PM2.5. The spatial distribution of these sources varied distinctly: secondary nitrate showed lower contributions in central areas but higher in western and southeastern regions; secondary sulfate was more prominent in the southeast, while vehicle emissions contributed more in the southeast and less in the west. Additionally, aerosol liquid water content promoted the secondary formation of nitrate and sulfate, exacerbating PM2.5 pollution. Secondary organic carbon was elevated in areas with high pedestrian density, suggesting enhanced secondary organic aerosol formation under intensive human activity. The study provides insights for targeted pollution control strategies in Changsha and similar cities.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025051404
Rubber additives, such as 1,3-diphenylguanidine (DPG) and p-phenylenediamine antioxidants (PPDs), are widely used in the rubber industry and have been increasingly detected in aquatic environments. This study investigated the distribution characteristics and potential sources of seven typical rubber additives (DPG, 6PPD, IPPD, DPPD, CPPD, DNPD, and 77PD) and the transformation product 6PPD-Q in surface water of the Guangzhou section of the Pearl River, China. A total of 29 sampling sites were analyzed. Total concentrations of the target compounds ranged from 205 to 5400 ng·L−1, with a mean of (820±1100) ng·L−1. DPG was the dominant compound in both dissolved and particle phases, accounting for (99±1.9)% and (66±13)% of the total concentrations, respectively. Source analysis indicated that aquaculture, vessel navigation, agricultural runoff, and wastewater treatment plant discharges likely influence the occurrence of rubber additives in this river section. Risk quotient (RQ) assessment revealed that 6PPD-Q posed high ecological risk at all sampling sites (RQ > 1), while DPG exhibited moderate to high risk at most sites (RQ > 0.1). In contrast, 6PPD, IPPD, CPPD, and DPPD showed low ecological risk. These findings highlight the need for heightened attention to the ecological risks posed by 6PPD-Q and DPG in the Pearl River Basin and provide scientific data for pollution prevention and risk management.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025041701
Landfill leachate leakage poses a significant threat to groundwater quality, particularly from informal landfills lacking proper containment. This study investigates the redox zoning characteristics of groundwater contaminated by leachate from the TS informal landfill in Southwest China. Based on redox-sensitive indicators and microbial community structure, the spatial evolution of redox conditions along the groundwater flow path was delineated. Results show that from the proximal to distal zones of the contaminant plume, oxidation-reduction potential (ORP) and dissolved oxygen (DO) increase significantly, while concentrations of Fe2+, NH4+, TOC, and HCO3− decrease markedly. The percentage of NO3− increases, indicating a transition from reducing to oxidizing conditions. Microbial communities shift correspondingly from anaerobic to aerobic populations. The infiltration of leachate introduces substantial reducing substances, creating a reducing environment that gradually oxidizes as dissolved organic matter is depleted. The plume is sequentially divided into sulfate reduction, iron reduction, manganese reduction, nitrate reduction, and oxidation zones. This redox zoning significantly attenuates pollutants, reducing the impact of leachate on groundwater. The findings provide a scientific basis for groundwater pollution prevention and control.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025050803
This study systematically investigates the synergistic drag reduction mechanism of surfactants and porous media in coal seam water injection. Four surfactant types—cationic CTAB, anionic SDBS, amphoteric BS-12, and nonionic OP-10—were tested with five porous media pore sizes (3–12 mm) using a custom-built all-in-one drag reduction test system. The effects of surfactant type, mass concentration, driving frequency, and pore diameter on drag reduction efficiency were evaluated. Results show that in an empty tube, drag reduction efficiency increases with mass concentration. As driving frequency increases, drag reduction first rises then falls, peaking at 35 Hz. With porous media, drag reduction exhibits pore size dependence, reaching a maximum at 8 mm and decreasing thereafter. The composite surfactant-porous media system achieves synergistic enhancement over single systems. At 0.05% mass concentration, all surfactants attain maximum drag reduction, with CTAB showing the highest efficiency. Optimal conditions (0.05% CTAB, 35 Hz, 8 mm pore size) yield a drag reduction rate of 66.14%, a 1.4-fold improvement over 20 Hz. These findings demonstrate that tailoring surfactant and porous media parameters can significantly optimize coal seam water injection efficiency, offering a practical approach for dust control in mining.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608017
Carbon monoxide (CO) is a significant gaseous pollutant emitted during high-carbon ferrochrome (HCFeCr) production, yet measured emission factors for different furnace types remain scarce, hindering accurate emission inventories and pollution control assessments. This study addresses this gap by investigating four typical HCFeCr production facilities in Ulanqab, Inner Mongolia, China, comprising two semi-closed submerged arc furnaces (SAFs) and two closed SAFs. A hybrid methodology combining manual stack sampling and continuous emission monitoring system (CEMS) data was employed. A characteristic CO-to-NOx concentration ratio was established from manual measurements, which was then applied to continuous NOx data to estimate CO emissions and product-based emission factors. Results revealed substantial process-dependent variability: semi-closed SAFs (Facilities A and B) exhibited CO emission factors of 7.06 kg/t and 3.66 kg/t, respectively, whereas closed SAFs (Facilities C and D) with associated pelletizing processes showed notably lower factors of 1.41 kg/t and 0.51 kg/t. On average, semi-closed furnaces emitted approximately six times more CO per tonne of product than closed furnaces. Furnace sealing degree and raw material ratios were identified as key determinants. These findings underscore the inadequacy of using a single average emission factor for HCFeCr production and advocate for furnace-type-specific factors to improve emission accounting accuracy. This study provides essential measured data for developing refined CO emission inventories and supporting pollution reduction policies in the ferroalloy industry.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608022
Since the first domestic sludge incineration project was commissioned at Shanghai's Shidongkou Wastewater Treatment Plant in 2004, sludge mono-incineration has been progressively adopted in economically developed Chinese cities. However, decentralized planning of wastewater treatment facilities and variable sludge characteristics complicate the centralized design and operation of incineration plants. This study, based on the planning and engineering design of a sludge incineration plant in Qingdao, analyzes sludge from major municipal wastewater treatment plants, which differ significantly in moisture and organic content due to varying influent characteristics and treatment processes. An energy balance model was constructed using data on sludge moisture and organic content, leading to a sludge allocation scheme and a simplified cost calculation method for heterogeneous sludge. This supports differentiated pricing and rational distribution in drying and incineration projects. Additionally, comparing conventional dewatering (to 76% moisture) and deep dewatering (to 65% moisture) from a "wastewater treatment plant + incineration" perspective, the study evaluates full-process costs and carbon emissions. Results show that deep dewatering increases dewatering costs and emissions but reduces transport and incineration costs and emissions, yielding lower total costs and emissions. The findings provide a basis for optimizing municipal sludge treatment planning and process selection.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3969-9
Phosphor-in-glass (PiG) materials are promising color converters for high-power laser illumination, yet suppressing interfacial reactions between phosphor and glass matrix at elevated sintering temperatures remains a critical challenge. Here, we report a Y3Al5O12:Ce3+ (YAG:Ce) phosphor-in-silica glass (PiSG) with high SiO2 content (>85 wt%) fabricated via a Cs2CO3 flux. Incorporation of Cs2O significantly inhibits SiO2-YAG:Ce reactions, preserving internal quantum efficiency (IQE) at 97.7% of pure YAG:Ce, and achieving 88.3% IQE even after calcination at 1400°C for 2 h. In contrast, smaller alkali ions (Li+, Na+) accelerate YAG:Ce decomposition. Mechanistic studies reveal that Cs+ with large ionic radius and weak interaction with oxygen suppresses non-bridging oxygen (NBO) formation, promoting a complete silica network that limits alkali ion diffusion. Leveraging the mixed alkali effect (10% Li2O + 5% Cs2O), the PiSG exhibits enhanced hydrothermal stability, withstanding 200°C treatment for 10 h. A PiG film-sapphire device delivers 3080 lm luminous flux and 213 lm W−1 efficiency under blue laser excitation. These findings establish YAG:Ce-PiSG as a highly promising color-conversion material for high-performance laser illumination.