SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4472-0
Dynamic electrocardiography (ECG) monitoring during physical activity remains compromised by motion artifacts that corrupt signal fidelity, particularly with conventional gel electrodes whose impedance rises sharply under deformation. This work presents a thumb-sized liquid metal system integrating gallium-based epidermal electrodes with a self-adhesive elastomeric matrix to sustain robust ECG acquisition against motion. The electrodes exploit the fluidic compliance of eutectic gallium–indium to maintain continuous skin contact, while the adhesive formulation ensures stable interfacial coupling without additional fixation. The system achieves low motion artifact levels, preserving waveform morphology and R-peak detectability during ambulation. The compact form factor enables unobtrusive wearability, and the materials architecture addresses the trade-off between adhesion and conformability that limits existing dry electrodes. The study establishes a materials and device pathway for clinical-grade dynamic ECG in ambulatory and point-of-care settings, with implications for continuous cardiac monitoring where patient movement is unavoidable.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4433-5
Negative thermal expansion (NTE) and zero thermal expansion (ZTE) materials are technologically relevant for precision engineering, yet their practical deployment is constrained by narrow operating temperature windows. This study introduces an entropy-designing strategy to regulate the thermal expansion behavior in the AⅠBⅡCⅢMo3O12 system, specifically K0.4(Mg0.25Mn0.25Co0.25Ni0.25)0.4Sc1.6Mo3O12 (CE0.4MO) and related CExMO compositions (x = 0.4, 0.6, 0.8, 1.0). By tuning configurational entropy, the operating temperature windows for both NTE and ZTE are significantly broadened, with the ZTE region shifting to higher temperatures. Among single-phase compositions, CE0.4MO exhibits the lowest configurational entropy and demonstrates NTE from 100 to 830 K and ZTE up to 1100 K, surpassing most reported ZTE materials. Systematic analyses of structural evolution, lattice dynamics, and electronic structure reveal that reduced configurational entropy suppresses structural evolution, directly correlating with decreased structural flexibility. Higher atomic displacement parameters (ADPs) of oxygen in CE1.0MO provide experimental evidence for enhanced flexibility. Raman spectroscopy shows that the full width at half maximum (FWHM) of peaks in the 750–900 cm-1 range positively correlates with configurational entropy, indicating reduced lattice disorder, while modes within 750–1050 cm-1 blue-shift as entropy decreases, confirming lattice stiffening. Electron localization function (ELF) and charge density analyses indicate that Mg/Mn/Co/Ni/Sc–O bonds are ionic, with ionicity weakening as configurational entropy decreases, thereby enhancing constraints on atomic vibrations and reducing structural flexibility. This work establishes a theoretical foundation for designing thermal expansion materials with wide operating temperature ranges.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4371-6
The sluggish kinetics of the oxygen reduction reaction (ORR) necessitates platinum-based catalysts, but their high cost and scarcity drive the search for platinum-group metal-free (PGM-free) alternatives. Fe−N−C catalysts with atomically dispersed Fe−N4 sites are promising, yet their practical performance is limited by buried active sites and poor mass transport. Here, a crumpled, multi-scale porous Fe−N−C catalyst (Fe−N−PCG) is synthesized via spray pyrolysis coupled with high-temperature metal etching. The crumpled morphology, formed by capillary compression during rapid solvent evaporation, and in-plane mesopores from Fe nanoparticle etching, synergistically enhance site accessibility and mass transport. Fe−N−PCG achieves a site density (SD) of 2.74×10^19 sites g−1 and Fe utilization (UFe) of 51.7%. As a gas diffusion electrode, it delivers a mass transport overpotential (ηmt) of 67 mV at 800 mA cm−2. In zinc-air batteries, Fe−N−PCG exhibits a peak power density of 296.1 mW cm−2 at 500 mA cm−2, outperforming Pt/C (241 mW cm−2 at 438 mA cm−2). At 50 mA cm−2, it delivers a discharge voltage of 1.19 V and a specific capacity of 815 mAh g−1, surpassing Pt/C (1.13 V, 715 mAh g−1). These results demonstrate that morphology and porosity engineering can concurrently optimize intrinsic activity, site utilization, and mass transport, offering a rational design strategy for high-performance PGM-free catalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4248-2
Marine biofouling imposes substantial operational penalties on maritime assets, yet commercial silicone foul-release coatings rely on static, non-adaptive networks that cannot be reprocessed or repaired. This work introduces selenonium-salt-catalyzed dynamic siloxane exchange as a route to polydimethylsiloxane (PDMS) vitrimer coatings. The authors incorporate A16Se+ organoselenium catalysts into PDMS networks at loadings designated A16Se+xPDMS, enabling thermally activated siloxane bond exchange that confers vitrimeric stress relaxation, reprocessability, and high-temperature self-healing. Antibiofouling performance is benchmarked against pristine PDMS using colony morphology assays for Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa, SEM imaging of bacterial adhesion after 3 h, Chlorella fluorescence adhesion quantification, zeta potential measurements, and 3-month seawater immersion panels. Reviewer 1 questioned the direct relevance of recyclability and high-temperature self-healing to marine antifouling and requested that surface elastic modulus and Pseudomonas antibacterial data be elevated to the main text. In response, the authors relocated scratch and self-healing results from Figure 5 to Supporting Information Figures S12 and S13, condensed the main-text discussion, and integrated surface elastic modulus data into Figure 4G and Pseudomonas antibacterial results into Figure 6A. The revised manuscript positions dynamic exchange as supporting evidence of network dynamics rather than as a primary antifouling metric, while foregrounding modulus and antibacterial performance as the application-relevant properties.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4267-y
The synthesis of two-dimensional MBenes from MAB-phase ceramics is impeded by uncontrolled etching kinetics that compromise structural integrity and yield. This study introduces a vacuum molten salt strategy to regulate space-charge accumulation during the selective removal of Al from Mo2AlB2, producing honeycomb-like architectures. The vacuum environment suppresses oxidative side reactions and modulates ionic transport, enabling precise control over etching depth and morphology. The resulting Mo2AlB2 exhibits exceptional electromagnetic wave absorption, with a minimum reflection loss of -56.3 dB at 2.4 mm and an effective absorption bandwidth of 6.8 GHz. These metrics surpass conventional etching-derived MBenes by a factor of 2.5 in attenuation capacity. The space-charge-regulated mechanism is elucidated through in situ spectroscopic and computational analyses, revealing that vacancy-induced charge redistribution governs the etching front propagation. This work establishes a scalable route for high-purity MBenes with tailored porosity, addressing critical bottlenecks in energy absorption and catalytic applications. The vacuum molten salt approach eliminates the need for hazardous HF, offering a safer and more environmentally benign pathway for industrial translation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4362-y
The commercial viability of zinc-air batteries (ZABs) is constrained by the sluggish kinetics of the oxygen reduction reaction (ORR), which necessitates robust, cost-effective catalysts. While cobalt-based single-atom catalysts (Co SACs) exhibit superior selectivity and stability relative to Fe-N-C counterparts, their intrinsic ORR activity remains limited by scaling relations among intermediates. This study alleviates these constraints by precisely engineering the coordination symmetry of Co SACs. Through a mild annealing strategy, boron was incorporated into the first and second coordination shells of Co centers, creating an asymmetric Co-N3B-O local environment. The first-shell B/O coordination modulates the electronic structure of the Co center, while hydrogen bonding between *OOH and the coordinated O atom stabilizes the key intermediate, synergistically enhancing ORR activity. The optimized Co-BCN-950 catalyst delivers a peak power density of 216 mW cm-2 in ZABs, a 43% enhancement over commercial Pt/C (151 mW cm-2), alongside an open-circuit voltage of 1.43 V and a specific capacity of 790 mAh g-1. These findings establish a paradigm for tailoring the local coordination of SACs, enabling next-generation high-stability energy storage systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4383-8
Conventional cancer therapies remain constrained by undruggable oncogenic proteins and acquired resistance. Proteolysis targeting chimeras (PROTACs) have emerged as a transformative modality that harnesses the ubiquitin-proteasome system to selectively degrade target proteins, offering advantages over traditional small-molecule inhibitors. However, clinical translation of PROTACs is impeded by intrinsic physicochemical limitations: high molecular weight, poor bioavailability, and lack of tumor-specific delivery. Integrating PROTACs with nanotechnology has yielded advanced nano-PROTACs platforms. Nanocarriers enhance solubility and stability, optimize pharmacokinetics, and enable spatiotemporally controlled drug release through passive or active targeting. This review systematically summarizes recent advances in engineering multifunctional nano-PROTACs for cancer therapy, with particular emphasis on design strategies by which nanoengineering enhances PROTAC performance. We evaluate how these platforms improve anticancer efficacy and minimize systemic toxicity while exploring their therapeutic potential in monotherapy and synergistic treatment settings. Finally, we discuss current challenges and future perspectives, providing a theoretical and technical foundation for next-generation nano-PROTACs as a precise and potent strategy in precision oncology.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4412-y
GeTe-based thermoelectric materials are promising lead-free alternatives to PbTe, but their intrinsically high Ge vacancy concentration (~10^21 cm^-3) leads to excessive carrier density and degraded Seebeck coefficient. This study integrates resonant levels (RLs) via In doping and local van der Waals gaps via Sb/Bi alloying to decouple electron and phonon transport. The optimal composition Ge0.91Sb0.04Bi0.04In0.01Te exhibits a Seebeck coefficient of ~287.31 μV K^-1 at 323 K, more than double that of the In-free sample (~102.28 μV K^-1). The peak figure of merit zT reaches ~1.8 at 723 K, with an average zT of ~1.0 over 323–723 K. Vickers hardness is enhanced to ~224 HV, a ~93% improvement over pristine GeTe (~116 HV). X-ray diffraction reveals a structural evolution toward a pseudo-cubic phase with increasing In content, and the (202) peak shifts to lower angles, indicating lattice expansion. These results demonstrate that synergistic RLs and van der Waals gaps effectively optimize carrier concentration and suppress thermal conductivity, offering a viable route for high-performance, mechanically robust GeTe thermoelectrics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4405-9
Conventional metal-halide X-ray scintillators, including Bi4Ge3O12 (BGO), Cs(Na)I:Tl, and Lu1.8Y0.2SiO5:Ce (LYSO), suffer from hygroscopic decomposition, high-temperature fabrication, and mechanical rigidity, which restrict their deployment in harsh-environment radiography. This study reports a nontoxic zero-dimensional organic–inorganic hybrid copper(I) halide, Cu2I2(C26H36NP)2 (Compound G), synthesized via a room-temperature solution route. The bulky phosphine ligands confer exceptional superhydrophobicity, with the material retaining 91.95% of its initial luminescence after 30 days of water immersion. A flexible scintillator screen fabricated from styrene-ethylene-butene-styrene (SEBS) exhibits a light yield of ~32,500 photons MeV-1, a spatial resolution of 19.14 lp mm-1, and a detection limit of 0.8 μGyair s-1. The screen enables stable X-ray imaging under flexible, high-temperature, and underwater conditions, eliminating vignetting and distortion in nonplanar objects. These metrics demonstrate that the superhydrophobic copper(I) halide scintillator addresses the water-stability bottleneck of commercial scintillators while delivering competitive light output and resolution, offering a viable pathway for medical diagnosis, nondestructive inspection, security checking, and space exploration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4416-8
Copper(I)-based carbene-metal-amide (CMA) emitters offer an earth-abundant alternative to precious-metal phosphors for organic light-emitting diodes (OLEDs), yet efficient green emission remains scarce due to limited π-extension and unbalanced charge-transfer characteristics of N-heterocyclic carbene (NHC) ligands. This work introduces a pyrimidine-fused NHC ligand (CF3PMI) with balanced π-accepting ability, synthesized via a one-pot protocol in good yields. The resulting Cu(I)-CMA complex CF3PMI-BFCF3 exhibits green thermally activated delayed fluorescence (TADF) in doped thin films, with a photoluminescence quantum yield (PLQY) of 90% and a short emission lifetime of 1.16 μs. A vacuum-deposited OLED achieves green electroluminescence centered at 514 nm with an external quantum efficiency (EQE) of 22.7%. Furthermore, a hyperfluorescent OLED employing CF3PMI-BFCF3 as a sensitizer delivers an EQE of 21.8%, green emission at 537 nm, and a narrow full width at half maximum (FWHM) of 30 nm. These results establish a viable molecular design strategy for high-performance green-emitting Cu(I)-based TADF materials and provide a convenient synthetic route for Cu(I)-CMA emitters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4238-2
Infrared nonlinear optical (IR NLO) materials are critical for laser frequency conversion, yet their performance is often constrained by a trade-off between second harmonic generation (SHG) efficiency and laser-induced damage threshold (LIDT). Here, we report a new ternary diamond-like compound, AlGaS3, which successfully balances these competing demands. AlGaS3 crystallizes in a noncentrosymmetric structure composed of wide HOMO-LUMO gap [AlS4] tetrahedra and NLO-active [GaS4] tetrahedra. The compound exhibits a wide experimental optical band gap of approximately 3.38 eV, which is significantly larger than that of the benchmark AgGaS2 (AGS, ~2.70 eV). This wide band gap contributes to a high laser-induced damage threshold (LIDT) of approximately 6.0 times that of AGS, as determined by powder-based measurements. Notably, AlGaS3 also demonstrates a phase-matching SHG response of approximately 0.5 times that of AGS at a fundamental wavelength of 2.09 μm, with particle size-dependent behavior confirming phase-matchability. The combination of wide band gap, high LIDT, and moderate SHG response positions AlGaS3 as a promising candidate for high-power IR NLO applications. This work provides a viable strategy for designing IR NLO materials with enhanced laser damage resistance by incorporating wide-gap tetrahedral units.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4269-4
Self-assembled molecular interlayers (SAMs) are promising hole-selective contacts for high-efficiency organic solar cells (OSCs) due to their well-defined energy alignment and minimal parasitic absorption. However, their intrinsically limited mechanical robustness often leads to structural degradation and performance loss under mechanical deformation, restricting their application in flexible devices. Here, we report a nanoparticle-reinforced self-assembled composite interface that simultaneously enhances mechanical reliability and optoelectronic performance. Uniformly dispersed SiO2 nanoparticles are introduced as high-modulus reinforcing building blocks without disturbing molecular self-assembly. In contrast to NiOx nanoparticles, which suffer from aggregation and parasitic absorption, SiO2 nanoparticles exhibit excellent dispersion and optical transparency, enabling formation of a structurally compatible hybrid interface. Mechanistic studies reveal that SiO2 nanoparticles redistribute interfacial stress and form dynamic hydrogen-bond networks with phosphonic acid groups of 2PACz, providing efficient energy dissipation during cyclic deformation. Meanwhile, modulation of interfacial polarity extends the crystallization time window of the active layer, resulting in enhanced molecular ordering and improved charge transport. As a result, devices based on the SiO2/2PACz composite interface achieve a power conversion efficiency of 20.14% for rigid devices and 19.30% for flexible devices, placing the flexible devices among the highest-performing flexible OSCs reported to date, while retaining over 90% of their initial efficiency after repeated bending cycles. This work establishes a general strategy for overcoming the trade-off between electronic selectivity and mechanical robustness in ultrathin self-assembled molecular interfaces, providing design insights for high-performance flexible organic optoelectronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4202-3
Carbon dots (CDs) with absorption in the second near-infrared window (NIR-II, 900-1700 nm) hold promise for tumor theranostics, yet existing synthesis methods often involve complex procedures, harsh conditions, or lack precise control. Here we report a 'self-photooxidation-restructuring' strategy that enables structural reorganization of the carbon core in CDs, achieving a significant redshift of absorption into the NIR-II region. Under ultraviolet (UV) light irradiation, the precursor (B-CDs, absorption in UV region) generates singlet oxygen, which self-oxidizes aldehyde groups and the carbon skeleton of B-CDs to stronger electron-withdrawing carboxyl groups and carbon radicals, respectively. These processes facilitate the formation of new C=C bonds between isolated aromatic domains, thereby transforming B-CDs into novel CDs (N-CDs) characterized by enhanced donor-acceptor interactions and a redshift in absorption toward the NIR-II window. Various experimental data, including high-resolution XPS, FTIR, NMR, EPR, have proved the proposed formation mechanism. The novel N-CDs afforded a high photothermal conversion efficiency of up to 71.33%, which enabled 1064 nm laser-activated photoacoustic imaging (PAI)-guided photothermal therapy (PTT) in tumors. This work opens a new avenue for the synthesis and modulation of CDs in the NIR-II region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4354-9
This review systematically examines the synthesis-structure-property relationships of hybrid graphene and carbon fiber reinforced composites, encompassing polymer, metal, and ceramic matrix systems. The hybridization of graphene with carbon fibers addresses the intrinsic limitations of conventional composites, such as weak interfacial bonding and insufficient multifunctionality. The review consolidates recent advances in fabrication strategies, including electrophoretic deposition, layer-by-layer assembly, and precursor impregnation, which enable controlled graphene distribution and orientation. Critical analyses of mechanical, tribological, electrochemical, and anti-ablation properties reveal that graphene addition significantly enhances interfacial shear strength, thermal stability, and electrical conductivity. For instance, in copper matrix composites, the incorporation of reduced graphene oxide with short carbon fibers improves tribological performance, reducing wear rates under specific load conditions. In ceramic matrix composites, graphene-modified C/C-SiC composites exhibit superior anti-ablation resistance, with mass loss rates reduced by up to 30% at elevated temperatures. Furthermore, graphene-coated carbon fiber electrodes demonstrate high specific capacitance and cycling stability in energy storage applications. The review also addresses challenges such as dispersion uniformity, scalability, and cost-effectiveness, proposing future directions for industrial adoption. By providing a comprehensive framework, this work guides the design of next-generation hybrid composites tailored for aerospace, automotive, and energy storage sectors.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4342-3
Electron acceptors containing single-bond-linked building blocks offer attractive advantages for organic solar cells owing to their synthetic simplicity and structural modularity. However, achieving backbone planarity without compromising electronic compatibility remains a persistent challenge. Conventional conformational locking strategies based on alkoxy substitution can effectively suppress torsional freedom but often elevate the highest occupied molecular orbital energy level, limiting compatibility with widely used donor polymers. Here, we report a partially fused electron acceptor design that achieves intrinsic backbone planarity through heterocycle selection rather than side-chain-assisted conformational locking. By incorporating a benzodifuran core and furan-thiophene linkages, the resulting acceptors exhibit a near-coplanar backbone geometry as revealed by density functional theory calculations, without the need for electronically perturbing alkoxy groups. Devices based on the optimized acceptor (BDF-1) deliver a binary power conversion efficiency of 12.2%, and further improvement to 19.5% is achieved in a ternary blend with PM6 and BTP-eC9. The enhanced performance is accompanied by favorable morphology, balanced charge transport, and suppressed recombination losses. This work provides molecular-level insight into partially fused acceptor design and demonstrates that heteroatom-guided conformational locking offers a viable strategy for expanding the design space of acceptors with single-bond-linked building blocks while maintaining compatibility with mainstream donor systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4369-1
Sodium-ion batteries (SIBs) are promising alternatives to lithium-ion batteries for large-scale energy storage due to sodium's abundance and low cost. Among cathode materials, polyanionic compounds like Na3V2(PO4)2O2F (NVPOF) offer high energy density and dual voltage plateaus at ~3.6 and 4.0 V, but suffer from low electronic conductivity and sluggish Na+ diffusion. Here, we report a dual-modulation strategy combining high-valence Nb5+ doping and polydopamine-derived carbon coating to synthesize Na3V1.94Nb0.06(PO4)2O2F-C (NVPOF-Nb-C) via a hydrothermal route. X-ray diffraction and Rietveld refinement confirm that Nb5+ doping induces slight lattice expansion without altering the tetragonal I4/mmm framework. Density functional theory calculations reveal that Nb5+ doping optimizes the crystal structure and reduces the Na+ diffusion barrier, while the uniform carbon coating enhances electron transport. Consequently, NVPOF-Nb-C exhibits remarkably improved electrochemical performance, including high reversible capacity, excellent rate capability, and ultralong cycling stability. In a full cell with hard carbon anode, it delivers a high energy density of 487.2 Wh kg−1 at 1C and retains 91.51% capacity after 3000 cycles at 20C. This work provides a synergistic strategy to overcome the intrinsic limitations of polyanionic cathodes for practical SIB applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4262-7
The escalating demands of artificial intelligence, machine learning, and neural computing necessitate multifunctional optoelectronic devices capable of integrating sensing, memory, and processing. Two-dimensional van der Waals heterostructures (vdWHs) offer unique advantages, yet their practical deployment is hindered by complex architectures and inefficient mode-switching. Here, we demonstrate a MoTe2/SnS2 anti-ambipolar heterojunction device enabling single-gate reconfiguration among frequency doubling, broadband photodetection, and neuromorphic computing. The device exhibits a peak-to-valley ratio (PVR) of 465, ensuring efficient frequency doubling. As a photodetector, it operates across an exceptionally broad spectral range of 520–2200 nm, with outstanding responsivity and detectivity. Furthermore, the device emulates complete synaptic behaviors, including short-term plasticity (STP), long-term plasticity (LTP), and paired-pulse facilitation (PPF). Integrated into a reservoir computing (RC) system trained on a vehicle motion dataset, it achieves a directional recognition accuracy of 98.7%. This work establishes a paradigm for multifunctional integration and low-power neuromorphic computing, advancing next-generation intelligent optoelectronic systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4212-x
Idiopathic pulmonary fibrosis (IPF) is a lethal interstitial lung disease with limited therapeutic options. Current treatments, such as nintedanib and pirfenidone, target downstream fibrosis but fail to address the upstream drivers, including persistent alveolar epithelial injury and abnormal repair. This study presents an inhalable, reactive oxygen species (ROS)-responsive liposomal system (SAB/GC-1@Lip-cRGD) that co-delivers the antioxidant salvianolic acid B (SAB) and the thyroid hormone receptor β (TRβ) agonist Sobetirome (GC-1). The liposomes are surface-modified with cRGD peptides for targeted delivery to fibrotic lesions and possess a negative surface charge to enhance mucus penetration. In the high-ROS fibrotic microenvironment, the liposomes destabilize, releasing SAB and GC-1. SAB scavenges ROS to remodel the fibrotic niche, while GC-1 reactivates TRβ signaling, driving the differentiation of stalled Krt8+ transitional epithelial cells into functional alveolar type I (AT1) cells. In a mouse model of pulmonary fibrosis, SAB/GC-1@Lip-cRGD significantly reduced pro-inflammatory cytokines (TNF-α, IL-1β, IL-6) and TGF-β1 in bronchoalveolar lavage fluid and lung homogenates. The proportion of CD206+ M2 macrophages decreased from 27.4% in the model group to 6.2% after treatment, indicating potent anti-inflammatory and anti-fibrotic effects. This synergistic strategy of microenvironment remodeling and epithelial regeneration achieved robust collagen depletion, restoration of alveolar integrity, and recovery of pulmonary function, outperforming single-drug or non-targeted formulations. The work provides a generalized paradigm for integrating microenvironment regulation with regenerative repair in pulmonary diseases.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4235-6
Fluorite-structured oxides (HfO2, ZrO2) are promising for resistive random-access memory (RRAM) due to their scalability and tunable properties. However, achieving high resistive switching on/off ratios remains challenging. Here, we report a collaborative strategy combining Hf/Zr ratio optimization and Lu3+ doping to regulate band structure and oxygen vacancy concentration in Hf0.4Zr0.6O2 (LHZO) thin films. The resulting LHZO devices exhibit a resistive switching ratio of 8.4 × 10^4, two orders of magnitude higher than that of ZrO2 (1.2 × 10^3). Electrical characterization and synchrotron radiation photoemission spectroscopy reveal that Lu doping widens the bandgap to 4.95 eV, downshifts the valence band, and introduces defect states, collectively suppressing p-type conductivity and reducing off-state leakage current. Simultaneously, Lu3+ doping enriches oxygen vacancies, stabilizing ohmic conductive filaments in the on-state. This co-optimization of band structure and oxygen vacancies effectively enhances insulating properties in the high-resistance state and ohmic conductivity in the low-resistance state, leading to superior resistive switching performance with robust retention (>10^4 s). Our findings establish a fundamental strategy for tailoring electronic properties of doped HfZrO2 thin films toward high-performance RRAM applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4176-y
Three-photon microscopy (3PM) in the near-infrared-III (NIR-III) window (1600–1840 nm) enables high-resolution visualization of cerebral vasculature in vivo, but its imaging depth and quality are limited by the performance of fluorescent probes. Here, we report a probe optimization strategy transitioning from mirror symmetry to centrosymmetry, yielding a highly symmetric aggregation-induced emission (AIE) molecule, T4PQ. The centrosymmetric structure aligns donor-acceptor units, promoting uniform electron cloud delocalization and directional charge transfer, which enhances exciton formation and suppresses non-radiative decay, thereby increasing fluorescence quantum yield. This symmetry also boosts the three-photon absorption cross-section by enhancing electron delocalization and transition dipole moment, enabling stronger nonlinear optical responses under long-wavelength excitation. T4PQ nanoparticles (T4PQ NPs) exhibit an enhanced three-photon absorption cross-section, high fluorescence quantum yield, and excellent photostability. In murine models, T4PQ NPs achieved three-dimensional cerebrovascular imaging at a depth of 1785 μm and real-time hemodynamic observation in microvessels at 1006 μm depth, with good biocompatibility. These results validate the advantage of centrosymmetric molecular design for deep-brain imaging probes, offering a high-performance tool for neurovascular research.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4180-9
Developing highly active and stable electrocatalysts based on the lattice oxygen mechanism (LOM) for the oxygen evolution reaction (OER) represents a significant challenge in water splitting. Herein, we successfully introduce oxygen vacancies (Ov) into high-entropy MnFeCoNiCu layered double hydroxides (HE-LDHs) via a solution chemical reduction method utilizing a defect engineering strategy. By precisely tuning the concentration of oxygen vacancies, we effectively activate the lattice oxygen within the HE-LDHs. The optimized Ov-rich high-entropy LDHs (Ov-HE-LDHs) exhibit excellent OER catalytic performance, achieving a current density of 10 mA cm−2 with a remarkably low overpotential of only 210 mV in 1.0 M KOH electrolyte, which is substantially superior to pristine HE-LDHs (315 mV) and commercial IrO2 (330 mV). Furthermore, the catalyst demonstrates outstanding long-term stability, capable of stable operation for 500 h at a high current density of approximately 200 mA cm−2. Advanced X-ray absorption fine structure analysis elucidates the lower metal valence states, indicating the existence of oxygen vacancies, while isotope labeling experiments and in-situ electrochemical Raman spectroscopy strongly confirm the successful activation of the LOM pathway. Density functional theory calculations further validate that the shift in the OER mechanism towards LOM and the resulting reduction in the reaction energy barrier are the fundamental reasons for the catalyst’s enhanced intrinsic activity. This work proposes a novel strategy for activating lattice oxygen in high-entropy LDHs through defect engineering, offering new insights and experimental guidance for the design and development of highly efficient and stable high-entropy OER electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4112-6
Radiostrontium remediation is crucial for ecological protection and sustainable development of nuclear energy. However, efficient removal of 90Sr from complex radioactive liquid waste, especially under acidic conditions, remains challenging due to material instability and intense proton competition. Herein, the rapid and highly selective capture of Sr2+ in neutral and even acidic solutions has been achieved by a layered potassium phosphatoantimonate KSbP2O8 with excellent radiation and thermal stability. Under neutral conditions, it possesses high maximum adsorption capacity (qmSr = 110.25 mg g−1), rapid adsorption kinetics (the removal rate (RSr) of 91.54% within 30 min), and excellent selectivity for Sr2+, and facile regeneration. Particularly, even under acidic conditions (pH 2.0), KSbP2O8 still maintains excellent Sr2+ removal capacity (qmSr = 79.38 mg g−1), fast kinetics, and high selectivity. A mechanism study by multiple characterizations reveals that the efficient Sr2+ removal of KSbP2O8 mainly stems from ion exchange between Sr2+ and interlayer K+ in KSbP2O8, which is attributed to the synergy between the Sb5+-induced Brønsted acidity and the high charge density of the anionic framework. This study demonstrates the exceptional capability of phosphatoantimonates to selectively capture Sr2+ under acidic conditions, highlighting the potential of phosphatoantimonates as effective scavengers for radiostrontium remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4199-8
High-entropy borides (HEBs) represent an emerging class of high-entropy materials that have garnered significant attention as ultra-high-temperature ceramics (UHTCs). By leveraging the high configuration entropy effect, HEBs stabilize single-phase solid solutions, exhibiting a suite of properties unattainable in traditional binary borides. This review systematically consolidates research progress on HEBs, beginning with theoretical predictions and component design via first-principles methods. It then details typical HEB systems and principal synthesis techniques, including arc melting and spark plasma sintering. The core analysis evaluates the outstanding performance of HEBs, emphasizing exceptional mechanical properties such as ultra-high hardness and excellent fracture toughness, alongside high-temperature friction and wear behavior, and oxidation resistance. Finally, the review outlines application prospects in extreme environments like aerospace and cutting tools, while also addressing current challenges. The paper underscores the potential of HEBs to overcome the hardness-toughness trade-off inherent in conventional ceramics, driven by strong metal-boron hybridization. This comprehensive overview positions HEBs as promising candidates for next-generation thermal and mechanical protection systems, with future research directions focusing on optimizing compositions and processing to tailor properties for specific applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4153-2
Direct seawater electrolysis offers a promising route to green hydrogen production, circumventing freshwater scarcity. However, the presence of chloride ions (Cl−) poses severe challenges, including competing chlorine evolution reaction (CER) and corrosion of anode catalysts. Here, we report a dual-atom catalyst design, RuCr-Ni3P, where Ru atoms with strong chloride affinity and Cr atoms as Lewis acid centers are co-doped into a nickel phosphide matrix. This catalyst exhibits outstanding oxygen evolution reaction (OER) activity and selectivity in alkaline seawater, achieving stable operation for over 4000 hours at industrially relevant current densities. Mechanistic studies reveal that Cl− ions are selectively captured by Ru sites, forming a dynamic Ru–Cl coordination motif that electronically modulates adjacent Ni centers, promoting the formation of high-valent Ni>3+ species. This switches the OER pathway from the lattice oxygen mechanism (LOM) to the more efficient adsorbate evolution mechanism (AEM). Concurrently, Cr sites facilitate the formation of Cr–OH species, creating a localized alkaline microenvironment that further enhances OER kinetics. This dual-site synergistic mechanism transforms Cl− from a detrimental impurity into a beneficial chemical switch, concurrently enhancing both activity and stability. Our findings provide a paradigm shift in seawater electrolysis catalyst design, turning a longstanding challenge into an opportunity for efficient and durable hydrogen production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3608-8
Polymeric carbon nitride (PCN) is a promising photocatalyst for H2O2 production due to its visible-light response, low cost, and high selectivity for the two-electron oxygen reduction reaction (ORR). However, its H2O2 yield is limited by narrow light absorption, low charge separation efficiency, and insufficient active sites. Here, crystalline poly(heptazine imide) (PHI)-based carbon nitride with highly dispersed In sites and N defects was prepared via an ionothermal method using LiCl/KCl molten salts. The large π-conjugated system and N defects enhance visible-light harvesting. Remaining K+ ions in nitrogen cavities act as interlayer electron channels, while N defects induce asymmetric charge distribution on the heptazine network, promoting interlayer and in-plane charge separation and transfer. In sites accelerate charge transfer dynamics and serve as active sites for ORR. The synergistic effect of metal modification and defect engineering boosts electron delocalization, significantly improving photocatalytic activity. The H2O2 production rate of 10InPHI reaches 15.3 mmol g−1 h−1 via a two-step single-electron ORR pathway, underscoring the potential of modified carbon nitride for efficient H2O2 photosynthesis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3564-9
Sluggish water dissociation kinetics in the alkaline hydrogen evolution reaction (HER) hamper its practical production. Here, a heterojunction electrocatalyst featuring Ru-Ni(OH)2 interfaces on nickel foam (NF) with self-engineered built-in electric fields (BIEF) was synthesized via a simple in situ galvanic replacement reaction. The hierarchical Ru-Ni(OH)2/NF exhibits a record overpotential of 9.6 mV at 10 mA cm−2 for alkaline HER, surpassing most reported catalysts and commercial Pt/C. It also shows exceptional activity for hydrazine oxidation reaction (HzOR) at 100 mA cm−2 with a remarkably low potential of ca. 0.015 V vs. RHE. The assembled overall hydrazine splitting (OHzS) system integrating HER and HzOR requires a cell voltage of about 0.09 V to reach 50 mA cm−2, which is 1.637 V lower than the corresponding overall water splitting (OWS) device. Systematic analysis and calculation reveal that the BIEF induces redistribution of interfacial electrons for Ru, facilitating H2O dissociation and intermediate conversion, delivering ultra-high electrocatalytic performance. This work provides an avenue for design and preparation of electric field-mediated catalysts towards sustainable energy conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3645-3
Postoperative abdominal adhesion, a complication with morbidity exceeding 90%, imposes severe clinical and economic burdens. Existing bioadhesive barriers often exhibit unreliable adhesion to the slippery abdominal wall, risk mispositioning, and neglect frictional stimuli and inflammation. Inspired by the lubricated peritoneum, we developed a programmable adhesive dual-layer Janus patch (DJP) barrier integrating a lubricated layer and an adhesive matrix. DJP achieves rapid, noncovalent interfacial adhesion, subsequently enhanced 2.81-fold via covalent interactions, enabling repositioning within a short time window to improve surgical fault tolerance. The micron-scale poly(sulfobetaine methacrylamide) brush on the DJP surface provides hydration lubrication with a low coefficient of friction (0.06), mimicking peritoneal lubrication and reducing frictional damage to injured tissue. The catechol-containing copolymer confers antioxidative and anti-inflammatory properties, confirmed in vitro. In a rat model, DJP adhering to the injured site significantly reduced collagen deposition between the abdominal wall and cecum, preventing adhesion and promoting tissue healing compared to commercial barriers. This work provides a guiding reference for developing antiadhesive biomaterials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3746-x
The polyanionic compound Na3V2(PO4)2O2F (NVPOF) possesses a stable three-dimensional framework, high theoretical specific capacity, and favorable operating voltage, yet its sluggish Na+ diffusion kinetics and low electronic conductivity impede industrial application. This study proposes a dual regulation strategy combining carbon coating and heat treatment temperature to synergistically enhance crystallinity and electrochemical performance. NVPOF@C-400 and NVPOF@C-600 were synthesized via in-situ dopamine hydrochloride coating followed by heat treatment at 400 °C and 600 °C, respectively. Carbon coating at 600 °C significantly improved crystallinity and increased electronic conductivity by three orders of magnitude through the carbon layer's conductive network. The ~4.5 nm carbon layer effectively suppressed abnormal grain growth and secondary crystallization aggregation at high temperatures, maintaining uniform particle size of approximately 0.36 μm, which shortens Na+ diffusion pathways and prevents ion transport obstruction. Consequently, NVPOF@C-600 delivered a high discharge capacity of 102.5 mAh g−1 at 20 C and retained 96.5% capacity after 10,000 cycles. In a full-cell configuration with hard carbon (HC), NVPOF@C-600//HC achieved an impressive 89.3% capacity retention after 9,000 cycles. This work provides critical insights for practical implementation of high-performance NVPOF cathodes in sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3506-3
Metallic glasses (MGs) often suffer from sluggish hydrogen evolution reaction (HER) kinetics in neutral and alkaline media, with their catalytic performance predominantly confined to acidic environments. Herein, we reported a novel thermoplastic forming technique to fabricate a self-supported partially crystallized nanoporous Pt56.2Ni5.2Cu16.8P21.8 metallic glass (C-NPMG). The C-NPMG catalyst delivers ultralow overpotentials of 18.0 mV (0.5 M H2SO4), 42.2 mV (1 M KOH), and 88.0 mV (1 M phosphate-buffered saline (PBS)) at a current density of 10 mA cm−2, outperforming most state-of-the-art non-noble MGs and Pt-based benchmarks across all pH conditions. Notably, it maintains negligible performance decay for over 1000 h in alkaline electrolytes, showcasing superior stability. Experimental and computational analyses reveal that the enhanced HER activity arises from three synergistic effects: (1) the high-specific-surface-area nanoporous architecture that maximizes active site exposure; (2) the formation of crystallite-amorphous interfaces during partial crystallization, which lowers the energy barrier for H2 desorption; (3) the hierarchical super-hydrophilic and super-hydrophobic wettability of the C-NPMG, which optimizes mass transport and prevents electrolyte-induced corrosion. This work establishes a novel design paradigm for developing high-performance, pH-universal HER electrocatalysts by integrating structural nano-engineering and crystallite-amorphous phase synergy in metallic glass systems to overcome the trade-offs between performance and stability in electrochemical water splitting.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3652-2
Existing robotic end-effector gripping technologies often encounter challenges such as poor adaptability to environmental changes, incomplete deformation sensing, and insufficient adhesion stability, which can compromise operational safety and reliability. Here, we present the bio-inspired self-sensing suction cup, in which the core self-sensing capability is achieved by combining high-performance, laser-induced graphene/Ag NWs flexible sensors with a Wheatstone bridge design. The flexible sensors provide high sensitivity, while the Wheatstone bridge circuit enables accurate and stable detection of deformation during the gripping process. Integrated into the octopus-inspired suction cup, this system allows for real-time monitoring of deformation and adsorption stability. The self-sensing suction cup demonstrates good performance across a 0–25 kPa negative pressure range, with outstanding linearity (R2 = 0.993) and high sensitivity (GF = 10.436 kPa−1). Experimental results confirm that the suction cup can achieve stable adsorption under varying loads and enable real-time monitoring of the suction cup status during the gripping process. This design provides a promising solution for intelligent gripping systems, logistics, and object recognition in challenging environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3748-9
Direct regeneration is a sustainable solution for recycling spent lithium-ion batteries (LIBs), yet the irregular strains induced by the irreversible FePO4 phase after cycling hinder Li+ replenishment in spent LiFePO4 cathodes. This study proposes a lattice stress modulation strategy that reduces FePO4 to Fe2P2O7, reducing unit cell volume from 271.7 to 122.6 Å3, releasing residual stress and reconstructing continuous Li+ transport channels. The phase transformation reconstructs FeO6 octahedra, lowering the migration energy barrier for ions. This synergistically weakens steric effects, facilitating Li+ replenishment and eliminating Li-Fe anti-site defects. Regenerated LiFePO4 cathodes achieve 80.2% capacity retention after 1000 cycles at 2C, outperforming commercial cathodes. The work establishes fundamental principles for the pre-treatment stage of direct regeneration and provides a paradigm-shifting solution for sustainable LIB recycling.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3807-8
Electrocatalytic co-reduction of CO2 and nitrate offers a sustainable route for urea synthesis, valorizing nitrogenous waste and CO2. However, achieving high-performance urea electrosynthesis under ambient conditions remains challenging due to the need for simultaneous activation of CO2 and efficient H2O dissociation to supply active *H for *NOx hydrogenation, ultimately forming key C- and N-containing intermediates for C–N coupling. Here, we report a bifunctional Pd-single-atom-modified Cu (Pd1Cu) nanorod catalyst that synergistically promotes adsorption and stepwise activation of CO2 and H2O, steering the reaction pathway toward selective urea synthesis. Integrating experimental evidence, in situ spectroscopy, and computational analyses, we disclose that atomically dispersed Pd sites kinetically favor co-generation of *CO and *NH2 via H2O dissociation-driven proton transfer, forming an optimal intermediate balance. The dual metal active sites enhance C–N coupling via combined electronic and geometric effects, substantially lowering the reaction energy barrier and improving selectivity. This work provides a rational design strategy for advanced multifunctional catalysts for urea electrosynthesis, contributing to carbon neutrality and waste nitrogen valorization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3815-0
The development of bifunctional electrocatalysts capable of integrating biomass-derived platform molecule oxidation with organic reduction offers a promising strategy for simultaneously enhancing energy efficiency and generating high-value chemicals. However, designing catalysts that exhibit both high activity and stability in integrated systems remains a significant challenge. Herein, we report a self-supported electrode composed of nitrogen-doped carbonized wood (NCW) supported NiCo nanosheets (NiCo 0.3/NCW) that enables the electrocatalytic 5-hydroxymethylfurfural oxidation to produce 2,5-furandicarboxylic acid (FDCA) and the nitrobenzene reduction to yield aniline in an integrated electrochemical cell. The NiCo 0.3/NCW electrode achieves the production of FDCA and aniline at a low cell voltage of 1.7 V, with ~99% anodic and ~92% cathodic Faradaic efficiencies, respectively. Experimental characterizations disclose that the hierarchical porous NCW architecture promotes the dispersion of active sites, while nitrogen doping strengthens metal–support interactions. In-situ spectroscopic experiments combined with density functional theory (DFT) calculations reveal that cobalt incorporation tunes the electronic structure of nickel, thus optimizing substrate and intermediate adsorption, and lowering energy barriers. These effects ultimately enhance the performance of the natural wood-derived catalyst in integrated biomass valorization and selective organic electrosynthesis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3725-1
Conductive hydrogel-based stretchable electronics have been extensively investigated, with strain sensors being the most prominently studied. While mechanical properties significantly affect device performance, the systematic correlation between specific mechanical parameters and sensing performance remains rarely explored. This work compares the influences of Young’s modulus and mechanical hysteresis on sensing performance between highly entangled PAM-Li and double-network PAM-Li-Agar-3 strain sensors. Owing to the brittle agar network, which imparts a higher Young’s modulus and pronounced mechanical hysteresis to the double-network PAM-Li-Agar-3 hydrogel, the corresponding sensor requires a greater driving force for deformation and yields signals with poor reproducibility. In contrast, the PAM-Li hydrogel, characterized by highly entangled polymer chains, exhibits a lower Young’s modulus and negligible mechanical hysteresis. Consequently, signals from the PAM-Li strain sensor demonstrate enhanced sensitivity and stability. Therefore, this work demonstrates that a low Young’s modulus and minimal mechanical hysteresis are critical factors for achieving superior sensing performance in strain sensors, as systematically validated through comparative analyses across diverse application scenarios.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507021
The accumulation of heavy metals in soil around municipal solid waste landfills poses potential risks to human health. This study selected a municipal solid waste landfill and monitored the concentrations of eight heavy metals (Zn, Pb, Cd, Ni, Hg, Cu, As, Cr) in surrounding soil. The geo-accumulation index method was used for pollution assessment, and a health risk assessment model recommended by the USEPA, combined with Monte Carlo uncertainty analysis, was employed to evaluate the pollution status and health risks to nearby residents. Results showed that among the eight metals, Pb, Ni, and Cd exceeded risk screening values at 4.26%, 6.38%, and 4.26% of sampling points, respectively. Geo-accumulation indices indicated overall clean conditions (mean < 0), but slight pollution by Pb, Zn, Ni, Hg, and Cd at some points. Probabilistic risk assessment based on Monte Carlo simulation revealed that for both adults and children, the cumulative non-carcinogenic risk was negligible, while carcinogenic risk was acceptable. However, there was a very low probability (approximately 0.2%) of non-carcinogenic risk for children, and probabilities of unacceptable carcinogenic risk were 0.64% for adults and 3.21% for children. Nickel was the primary contributor to carcinogenic risk, and children faced higher health risks than adults. These findings provide a reference for pollution prevention and health risk management of soil around municipal solid waste landfills.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507032
To mitigate global warming, regional carbon neutrality pathways are critical. Based on the Guangdong Energy Policy Simulator (EPS) model, this study simulates total energy consumption and greenhouse gas (GHG) emissions under baseline, Carbon Neutral 60 (CN60), and Carbon Neutral 50 (CN50) scenarios, and analyzes the emission reduction effects and costs of various energy policies. Results show that by 2060, total energy consumption under CN60 and CN50 decreases by 39% and 44% relative to baseline, respectively. Primary electricity and other energy, natural gas, oil, and coal account for 56%, 26%, 14%, and 4% under CN60, and 60%, 24%, 13%, and 3% under CN50. GHG emissions under CN60 drop to 80×10^6 tCO2e by 2060, an 89% reduction from 2020; under CN50, emissions reach 92 and 55×10^6 tCO2e in 2050 and 2060, respectively, reductions of 87% and 92% from 2020. Policies such as increasing clean electricity share, industrial electrification (hydrogen), increasing green power purchases, building electrification, F-gas reduction, and improving industrial energy efficiency standards show significant reduction effects, with clean electricity share being the primary source. Policies like improving industrial energy efficiency standards, increasing industrial product utilization, and increasing clean energy vehicle market penetration are cost-effective; increasing clean electricity share, green power purchases, building electrification, and F-gas reduction effectively balance reduction effects and costs. Industrial electrification (hydrogen) contributes >5% cumulative reduction but faces economic challenges for full-scale promotion in the short term; industrial carbon capture and storage and electrolytic hydrogen contribute <2% cumulative reduction with high costs. Therefore, Guangdong should prioritize cost-effective policies, promote balanced policies, gradually optimize energy structure, achieve clean electricity, and foster green industrial transformation to achieve carbon neutrality at lower economic cost.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024110202
Anaerobic digestion (AD) is an environmentally friendly biochemical technology for waste treatment and renewable energy production, yet its methane conversion efficiency remains suboptimal. This study employed flux balance analysis (FBA) to determine the optimal temperature for methane production in AD, and subsequently regulated key flexible nodes in the metabolic pathway to maximize methane flux. At the optimal temperature of 40 °C, up-regulating the acetyl-CoA flexible node increased methane flux by 48.5%, while up-regulating the acetate node increased it by 36.6%. The higher improvement via acetyl-CoA regulation is attributed to the fact that 40 °C is unfavorable for hydrogen-producing acetogenic bacteria, making acetyl-CoA the critical control point. These findings demonstrate that flexible node regulation can overcome the limitations of temperature optimization alone. The FBA methodology provides a reliable, cost-effective approach for optimizing target product yields in AD and other fermentation systems, requiring only input and output measurements to resolve intermediate metabolic fluxes.
Environmental Chemistry•2026•DOI: 10.0000/202604-1
An analytical method was developed for the simultaneous determination of 11 organic ultraviolet absorbents (OUVs) in coral tissues using ultra-high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS). Target analytes included benzophenones (BP, BP-2, BP-3, BP-8) and other common UV filters. Sample pretreatment and chromatographic conditions were systematically optimized. Coral tissue samples were extracted by combined vortexing and ultrasonication, separated on a CAPCELL PAK MG C18 column using a mobile phase of methanol-0.1% formic acid aqueous solution under gradient elution, and determined by multiple reaction monitoring (MRM) with internal standard quantification. Method validation demonstrated good linearity for all target compounds over the range of 0.1–500 μg·L−1 (R2 > 0.990), with method detection limits ranging from 0.020 to 0.133 ng·g−1. The mean recoveries at low, medium, and high spiking levels ranged from 60.5% to 120.3%, with relative standard deviations (RSDs) of 1.6%–10.7%. The method offers advantages of simple pretreatment, good repeatability, and high accuracy, making it suitable for high-throughput determination of OUVs in complex biological matrices such as corals. The method was applied to analyze 89 coral samples collected from Xidao Island, Sanya, and five target OUVs were detected in the samples. This method provides reliable technical support for elucidating the accumulation characteristics of OUVs in corals and assessing their potential ecological risks.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604001
This study systematically investigated the occurrence, spatial distribution, sources, and ecological risks of 160 pesticides in Dianchi Lake, a typical plateau lake impacted by agricultural activities. A total of 37 pesticides were detected in the water, with total concentrations ranging from 64.2 to 1132.8 ng/L (average 610.0 ng/L). Fungicides, including boscalid (BOS), fluopicolide (FPC), and dimethomorph (DMM), were dominant, contributing up to 65.0% of the total concentration. Spatially, the southern lake region exhibited significantly higher concentrations (672.5 ng/L) than the north, attributed to intensive facility agriculture. Highly hydrophobic pesticides, such as penconazole (PEN), showed a tendency to enrich in bottom layers. Source apportionment identified inflowing rivers and wastewater treatment plant effluents as primary input sources, with average concentrations 7 and 9 times higher than lake water, respectively. Ecological risk assessment revealed that pesticides posed the highest risk to algae, followed by daphnia and fish. Prometryn (PMT) was identified as a high-risk factor for algae, while profenofos (PFF) and carbendazim (CBD) posed potential threats to higher trophic levels. These findings provide fundamental data and technical support for understanding pesticide pollution in plateau lake ecosystems.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604011
Reverse osmosis (RO) membrane fouling remains a critical bottleneck in reclaimed water production, yet its spatial heterogeneity over extended operation is poorly understood. This study investigated fouling characteristics and microbial community dynamics on RO membranes after 3.5 years of operation in a full-scale microfiltration-reverse osmosis (MF-RO) system treating reclaimed water. Long-term monitoring showed stable effluent quality (turbidity <0.1 NTU, conductivity <400 μS/cm), but RO inlet pressure exhibited seasonal fluctuations of 15%–22% between summer and winter, attributed to water viscosity changes. Membrane autopsies revealed distinct fouling layers at the inlet (RO1) and outlet (RO2) ends. RO1 featured a dense bio-inorganic composite fouling layer with CaSO4 crystals and rod-shaped microbial aggregates (5–10 μm), dominated by Proteobacteria (77.11%), particularly Alphaproteobacteria (71.49%) and Xanthobacteraceae (35.29%), which secreted extracellular polymeric substances (EPS) to form biofilms. In contrast, RO2, exposed to higher salinity, showed reduced microbial abundance (Proteobacteria decreased to 64.79%) and a shift toward halotolerant taxa, including Microbacteriaceae (23.73%) and Actinobacteriota (24.76%), with EPS secretion increased by 42%. Alphaproteobacteria relative abundance dropped by 19.3%, while Gammaproteobacteria rose to 12.54%. These findings elucidate salinity-driven microbial succession and spatial heterogeneity of fouling, providing a basis for targeted antifouling strategies and 'zonal-graded' cleaning protocols in reclaimed water plants.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225200
Phosphogypsum, a by-product of wet-process phosphoric acid production, poses severe environmental and safety challenges due to its massive annual output and stockpiling. This study addresses the urgent need for resource utilization by employing phosphogypsum as the primary raw material, supplemented with ground granulated blast furnace slag, fly ash, and type II anhydrite. Two foaming agents, sodium bicarbonate (NaHCO3) and aluminum powder, were used to regulate pore structure, and their effects on ceramsite performance were compared. Under identical preparation conditions, aluminum powder yielded higher 7-day cylinder compressive strength than NaHCO3. Optimal formulations achieved a maximum cylinder compressive strength of 6.5 MPa with a bulk density of 1020 kg/m3, meeting lightweight aggregate concrete strength requirements. Aluminum powder produced closed pores, reducing bulk density to as low as 765 kg/m3, while NaHCO3 generated interconnected pores leading to higher water absorption. XRD, SEM, and BET analyses revealed that strength-contributing phases are calcium silicate hydrate and calcium aluminate hydrate; trace heavy metals (Mo, Ti) hinder their formation, causing structural defects. This work demonstrates a green, non-fired route for phosphogypsum valorization, offering environmental and economic benefits and a pathway for large-scale utilization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3451-2
Visual aesthetics is a key metric of semi-transparent organic photovoltaics (ST-OPVs) for building-integrated solar windows, yet previous studies have primarily focused on the compromise between efficiency and transparency. This work addresses the overlooked aspect of full visual aesthetic control, particularly the bidirectional reflected color for architectural harmony, via designing ST-OPVs with double-sided ultra-thin Ag/TeO2 transparent electrodes. This design facilitates full-spectrum color tunability covering the whole standard color gamut of CIE coordinates on both surfaces, achieved simply by adjusting layer thicknesses. The resulting devices exhibit neutral transparency (16.6%–27.0% average visible transmittance) and competitive power conversion efficiencies (8.1%–9.2%). Additionally, the devices demonstrate strong flexibility, with flexibility-adaptive coloration and curvature-enhanced aesthetics. This work presents an ST-OPV design featuring full visual aesthetics and considerable performance, paving the way for commercialization of organic solar windows for building and vehicle integration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3782-0
Oral mucositis (OM) is a debilitating complication of cancer therapy, characterized by severe pain, mucosal barrier breakdown, and infection risk. Current hydrogel-based topical systems suffer from poor transmucosal permeation and lack of inflammatory microenvironment-triggered drug release. Here, we report a supramolecular strategy for designing guanosine-fibril hydrogels and derived microneedle patches. Tavaborole (Ta), crisaborole (Cr), and strontium (Sr2+) ions serve dual roles as structural building blocks and biofunctional agents. Unlike conventional G4·K+ fibrils, the unique G4·Sr2+-Ta/Cr fibrils incorporate Ta/Cr via boronic ester bonds on guanosine and Sr2+ through G-quartet cation recognition. This design mechanically reinforces the hydrogel through additional hydrophobic interactions and ion-pair recognition, while synergistically providing antimicrobial/anti-inflammatory effects (Ta/Cr), pro-angiogenic activity (Sr2+), and reactive oxygen species (ROS) scavenging (guanosine). The optimized gelation process enables fabrication of microneedle patches with pseudomembrane-penetrating capability and ROS-triggered drug release via boronic ester hydrolysis. In vivo mouse experiments confirm efficacy in controlling OM-associated inflammation, modulating oral microbiota homeostasis, and promoting angiogenesis at ulcer sites. This work demonstrates multifunctional integration via hierarchical structural design, extending guanosine supramolecular assemblies into bioactive platforms for OM treatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3545-7
Magnetically driven hydrogel robots show promise in biomedical and underwater applications due to remote controllability, flexibility, biocompatibility, and chemical stability. However, limited functional integration restricts their adaptability. Here, a universal modular assembly strategy is introduced using a self-healing κ-carrageenan/polyacrylamide hydrogel embedded with magnetic particles, enabling free assembly of magnetic actuation modules. These modules construct soft robots with complex geometries and magnetization distributions, allowing diverse deformations under magnetic fields. The strategy further integrates photocatalysis by embedding Ru-Bi2CrO6 photocatalysts into functional modules, yielding an oxygen-generating robot. This robot exhibits flexible underwater movement via magnetically controlled oscillatory actuation, minimizing water agitation while supplying stable oxygen to specific aquatic environments. The photocatalytic oxygen evolution rate reaches 389.1 μmol g−1 h−1. The hydrogel skeleton suppresses particle aggregation and sedimentation, and facilitates magnetic recovery. This scalable and adaptable approach advances multifunctional soft robot design.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507094
To address land waste and poor bearing capacity from sludge landfill, this study developed a composite solidifying agent using loess, fly ash, desulfurized gypsum, and cement. Orthogonal experiments combined strength testing, SEM/XRD microanalysis, permeability and heavy metal leaching tests, and cost accounting. Results show that cement significantly enhances early and mid-term strength, while loess dominates later strength development. Optimal fly ash and desulfurized gypsum content is 12% each. The optimal mix ratio (loess:fly ash:desulfurized gypsum:cement:sludge) is 0.1:0.12:0.12:0.08:1. The solidified matrix forms dense structures via C-S-H gel and ettringite (Aft), effectively controlling heavy metal leaching at low cost. This work enables solid waste resource utilization and provides robust support for sludge solidification engineering.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60629-3
This study reports the synthesis of a novel Z-scheme heterojunction composite film comprising Ag/Bi2MoO6/BiOBr via electrochemical processes, ion-exchange techniques, and subsequent photodeposition of silver nanoparticles. The incorporation of Ag nanoparticles exploits localized surface plasmon resonance (LSPR) effects and serves as an electron mediator, establishing a Schottky barrier that suppresses charge recombination. The optimized 1.5% Ag/Bi2MoO6/BiOBr film achieves a CO production rate of 13.65 μmol/(g·h) from photocatalytic CO2 reduction, significantly outperforming the unmodified Bi2MoO6/BiOBr film. Photocurrent and impedance analyses confirm enhanced charge separation in the Ag-modified composite. A non-linear relationship between Ag loading and photocatalytic efficiency was observed, with optimal performance at 1.5% Ag. The proposed Z-scheme mechanism elucidates the synergistic interactions among components, providing a scientific basis for rational design of advanced photocatalysts and immobilized systems for CO2 reduction. This work offers insights into the development of efficient, sustainable photocatalytic technologies for carbon capture and utilization.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012501
Dibutyl phthalate (DBP) is a ubiquitous environmental pollutant posing potential risks to aquatic ecosystems. This study assessed the developmental toxicity of DBP in Japanese medaka (Oryzias latipes) embryos. Embryos were exposed to gradient DBP concentrations (1, 5, 50, 500 μg·L−1, and 5 mg·L−1) for 15 days. Endpoints included embryonic heart rate, hatching time, survival rate, larval swimming behavior, and expression of genes related to cardiovascular, nervous, thyroid, antioxidant systems, and estrogenic effects. Results showed that 5 mg·L−1 DBP significantly reduced embryonic heart rate (P < 0.0001), leading to hatching failure and mortality. Exposure to 500 μg·L−1 DBP significantly reduced hatching rate (P < 0.01) and survival rate (P < 0.0001). DBP exposure caused developmental delay, cardiovascular hemorrhage, spinal curvature, yolk sac edema, and inhibited larval swimming behavior. At the molecular level, DBP significantly altered expression of atrap, dkk1, bnpa, fx, and dvl mRNA, affecting cardiovascular development; downregulated trha, mbp, and elavl3 mRNA, indicating endocrine disruption and neurotoxicity; upregulated cat, gpx2, and gsta mRNA, inducing oxidative stress; and upregulated vtg1, erβ1, and chgl mRNA, demonstrating estrogenic effects. This study demonstrates that DBP exposure adversely affects growth, development, hatching, survival, swimming behavior, and gene expression in Japanese medaka embryos, highlighting ecological risks of DBP pollution in aquatic environments.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025092802
Activated carbon (AC) filters in drinking water treatment plants (DWTPs) experience significant adsorption performance decline over extended operation, yet complete media replacement is a major cost. To evaluate cost-effective strategies, pilot-scale column experiments with five AC replacement ratios (0%, 30%, 50%, 70%, and 100%) were conducted to assess removal of disinfection by-product (DBP) precursors and pesticide-related emerging contaminants. For dissolved organic matter (DOM), all fractions except low molecular weight compounds (LMWC) achieved >85% of the removal obtained with full replacement when 70% new AC was used, with UV254 removal reaching 70%. LMWC, due to small molecular size and low adsorption energy, required higher replacement ratios or full replacement for substantial removal. For DBPs, removal of trihalomethanes (THMs) and haloacetic acids (HAAs) was insensitive to replacement ratio, while haloacetaldehydes (HALs) removal improved markedly with increasing ratio, indicating structural selectivity. For pesticide-related contaminants, all except triazoles achieved >95% removal at 70% replacement; triazoles, due to high water solubility, high polarity, and low octanol-water partition coefficient, achieved only ~60% removal. Overall, replacing 70% of AC restored treatment performance to >80% of that with full replacement, ensuring effluent quality while saving ~30% of new carbon cost. Molecular structure, polarity, and pore size matching are key determinants of removal efficiency; optimizing replacement ratio balances water quality and economic benefits.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025111302
High-concentration chloride ions (Cl−) in industrial wastewater cause severe corrosion and environmental hazards. Conventional removal methods suffer from low efficiency, high cost, and difficulty in product recovery. This study fabricated porous metallic bismuth-based blocks (Bi-PM) via 3D printing, combining chemical precipitation with additive manufacturing. Systematic evaluation of Cl− removal under varying pH and light irradiation revealed that at pH 0.1 and 0.5, dark-condition efficiencies were 53.6% and 31.0%, respectively, increasing to 69.3% and 38.1% under light. Radical trapping identified photogenerated holes as the primary active species, oxidizing metallic Bi to release Bi3+ and enhance precipitation. At pH 0.5, Bi-PM exhibited balanced efficiency and structural stability; over five cycles, average removal efficiency was 25% in darkness versus 41.2% under light, with superior stability under illumination. XRD and SEM confirmed abundant BiOCl formation on the surface under light, mitigating Bi loss. This approach ensures high chloride removal while minimizing material degradation, offering a novel pathway for industrial wastewater treatment.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605002
The single-phase partial nitrification and anammox (SPN/A) process has seen limited widespread application due to its slow startup and difficulties in enriching anaerobic ammonium-oxidizing bacteria (AnAOB). This study utilized high-ammonia nitrogen wastewater to initiate and enhance the SPN/A process in a pilot-scale integrated fixed-film activated sludge (IFAS) reactor. By establishing an IFAS-SPN/A coupled system based on the symbiotic relationship between biofilm and sludge, rapid startup and efficient AnAOB enrichment were achieved. An innovative sludge inoculation strategy was employed: first, conventional nitrifying sludge was inoculated to initiate shortcut nitrification and allow ammonia-oxidizing bacteria (AOB) to colonize blank carriers; subsequently, anammox sludge was inoculated to promote efficient AnAOB enrichment on the AOB biofilm. The influent was low-temperature shift condensation water from a synthetic ammonia workshop, with an average ammonium nitrogen concentration of 2300 mg/L and COD ranging from 50 to 200 mg/L. The 180-day experiment comprised three stages: shortcut nitrification startup, SPN/A startup, and load intensification. The system successfully started up SPN/A within 120 days, achieving total nitrogen removal efficiency and removal load of (90.21±2.18)% and (0.31±0.07) kg/(m³·d), respectively, through synergistic biofilm and suspended microorganisms. During load intensification, AnAOB relative abundances in biofilm and flocs reached 18.8% and 35.3%, respectively, and removal load increased to (0.64±0.11) kg/(m³·d). Stable influent quality is a prerequisite for efficient and stable nitrogen removal; a surge in influent ammonium concentration caused nitrite accumulation imbalance and deteriorated performance. Adding an equalization tank before the aeration tank mitigates water quality fluctuations, and a 'dilution-reconstruction' strategy for low-ammonia wastewater facilitates rapid recovery after performance deterioration.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605011
Phytoplankton are highly sensitive to environmental changes and respond rapidly, making their community dynamics crucial early warning indicators of lake ecosystem health. Previous studies have qualitatively analyzed the combined effects of multiple physicochemical water quality factors on phytoplankton communities, but few have quantitatively distinguished direct from indirect effects. This study employed correlation analysis, redundancy analysis, and structural equation modeling to investigate the spatiotemporal distribution of phytoplankton communities in Baiyangdian Lake and their driving factors. A total of 113 species belonging to 57 genera and 7 phyla were recorded. Phytoplankton density exhibited significant seasonal and spatial variability, peaking in summer. Diatoms and green algae dominated in spring, transitioning to cyanobacterial dominance in summer and autumn, and reverting to green algae in winter. Structural equation modeling revealed that water temperature had a total positive effect on phytoplankton biomass (β = 0.96), comprising a direct positive effect (β = 0.94, P < 0.05) and an indirect positive effect via increased abundance (β = 0.02). Total nitrogen (TN) had a negative total effect on biomass (β = -0.98), with a direct negative effect (β = -0.97, P < 0.05) and an indirect negative effect via reduced abundance (β = -0.01). TN also negatively affected abundance (β = -0.15, P < 0.05). These findings provide a scientific basis for ecosystem health assessment, eutrophication control, and biodiversity protection in Baiyangdian Lake.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605022
Carbide slag (CS), an alkaline industrial solid waste from acetylene production in the chlor-alkali industry, poses severe ecological risks due to long-term stockpiling. This review systematically examines CO2 mineralization pathways and applications of CS, leveraging its high reactivity dominated by Ca(OH)2. Direct gas-solid and liquid-solid carbonation mechanisms, alongside indirect ammonium salt cyclic leaching-carbonation, are elaborated. Process optimization via parameter regulation, amino acid modification, and multi-solid waste coordination significantly enhances reaction efficiency and product performance, enabling controlled synthesis of high-value calcium carbonate. Environmental and economic analyses confirm that CS mineralization achieves CO2 fixation with good economic feasibility, simultaneously addressing solid waste resource utilization and carbon emission reduction. Derived lightweight fillers and low-carbon cementitious materials exhibit both environmental and economic potential, providing theoretical and application support for a 'waste-to-waste' carbon reduction technology system.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605017
In response to the escalating challenge of industrial dust pollution, this study introduces a magnetic field-enhanced electrostatic dust collector integrated with wire mesh filtration. By applying an external magnetic field, the conventional electrostatic precipitation process is physically intensified. Systematic experiments compared discharge characteristics and dust removal efficiency with and without magnetic field intervention. The influence of wire mesh structural parameters was investigated, focusing on pore size (1, 2, 3 mm), number of stacked layers (1, 2, 3), and surface composite filtration materials (polyethylene filter mesh, polyamide mesh). Additionally, the effects of airflow velocity (1–5 m/s), inlet flow direction (forward/reverse), and dust type (fly ash, coal combustion dust, cement ash) on removal efficiency were tested. Results demonstrate that the optimized magnetic field-wire mesh coupling significantly enhances the charging and capture of fine dust. Specifically, smaller mesh apertures improve efficiency, with 1 mm yielding the best performance. Increasing the number of mesh layers effectively enhances efficiency at discharge voltages of 13–17 kV. Coating the mesh with either polyethylene or polyamide further improves efficiency, with negligible difference between the two materials. Reverse airflow direction results in lower effective gas velocity due to opposing gravity and drag forces, yet the combined magnetic and electric fields stabilize particle charging and enhance trajectory deflection, leading to improved overall performance. Dust resistivity is a critical factor: lower resistivity facilitates charging, while higher resistivity induces back corona, reducing efficiency. Magnetic field enhancement mitigates back corona and improves removal, particularly for high-resistivity cement ash. These findings offer a viable technical solution for efficient industrial flue gas dedusting.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.226111
Efficient capture of the greenhouse gas nitrous oxide (N2O) is critical for climate change mitigation and resource recovery. In this study, two guanidinium-based hydrogen-bonded organic frameworks (HOFs) with pyridyl nitrogen site isomerism, namely G-5,5'-BPyDC and G-4,4'-BPyDC, were constructed using 2,2'-bipyridine-5,5'-dicarboxylic acid and 2,2'-bipyridine-4,4'-dicarboxylic acid as ligands. The effects of ligand structure on hydrogen-bonded network, pore environment, and N2O/N2 adsorption separation performance were systematically investigated via single-crystal X-ray diffraction, thermogravimetric analysis, Hirshfeld surface analysis, and gas adsorption experiments. Both frameworks are built via N-H...O hydrogen bonds. The asymmetric unit of G-5,5'-BPyDC contains two methanol molecules, resulting in larger free volume and surface area compared to G-4,4'-BPyDC, which exhibits more compact packing. Both materials show decomposition temperatures above 290°C, indicating good thermal stability. Hirshfeld surface analysis reveals that the total contribution of O-H/H-O and N-H/H-N hydrogen bonds in G-5,5'-BPyDC (32.0%) is higher than that in G-4,4'-BPyDC (29.7%). At 25°C and 4.0 MPa, the N2O adsorption capacity of G-5,5'-BPyDC is 2.32 mmol/g, surpassing that of G-4,4'-BPyDC (2.02 mmol/g). IAST calculations show that the selectivities of G-5,5'-BPyDC for N2O/N2 (50:50 and 10:90) mixtures reach 29.26 and 111.32, respectively, significantly superior to those of G-4,4'-BPyDC (6.61 and 17.03). Pyridyl nitrogen site isomerism effectively optimizes N2O/N2 adsorption and separation by modulating pore polarity and hydrogen-bonded network, offering a new strategy for isomer design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3936-8
The precise separation of enantiomers is essential for developing effective chiral drugs, yet conventional membranes are constrained by the ubiquitous selectivity-permeability trade-off and low flux, limiting scalable production of single-enantiomer drugs. Herein, we present a cascade reaction strategy integrating Sonogashira-Hagihara coupling and Friedel-Crafts alkylation to fabricate porous conjugated microporous polymer membranes (CCMP-M P1–4/SiO2). This approach enhances specific surface area by 400-fold compared to the product from the Sonogashira-Hagihara coupling reaction alone, creating interconnected porous networks that facilitate mass transport. This hypothesis was confirmed by pore-size gradient experiments, which revealed a critical size-matching effect: matched molecular dimensions enable high-speed mass transfer with 97% enantioselectivity, while mismatch reduces selectivity to 9%, as visualized in a separation performance matrix across four chiral molecules. Precise chiral recognition is programmable via absolute configuration control of chiral monomers, with the mechanism of “preferential adsorption–interfacial enrichment–promoted diffusion” confirmed by static adsorption and density functional theory calculations. This strategy achieves breakthrough performance: Naproxen flux reaches 37 mmol m−2 h−1, surpassing literature values, and enables membrane-based separation of Raceanisodamine (89% selectivity of 6S, 2′S and 6R, 2′R-isomer after cascade enrichment) for the first time. This work provides a new paradigm for designing high-performance chiral separation membranes, facilitating scalable and sustainable production of single-enantiomer drugs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3993-y
Conventional liquid-phase in-situ synthesis of Cu-TiB2 composites often suffers from coarse and non-uniformly distributed reinforcements, stemming from insufficient understanding and control over the in-situ nucleation and growth mechanisms of TiB2 particles. This study introduces a novel melt dispersion-turbulent mixing (MDTM) in-situ reaction technology to fabricate high-performance Cu-TiB2 composites. The MDTM strategy synergistically refines reaction micro-regions by reducing the initial melt droplet size via melt dispersion while enhancing solute convection via turbulence, promoting high-density nucleation and refinement of TiB2 particles. Based on turbulence characteristics and in-situ reaction kinetics, we optimized the melt disperser parameters and established a quantitative model linking particle size to disperser rotation speed and reactant solute concentration. It was found that disperser rotation speed governs three distinct nucleation and growth mechanisms for TiB2 particles. Low-density nucleation at low disperser rotation speeds (0–50 r/min) leads to coarse TiB2 particles. At medium rotation speeds (100–150 r/min), the refinement of micro-regions in the dual-melt reaction achieves high-density TiB2 nucleation. Conversely, at high rotation speeds (150–200 r/min), intense turbulence weakens the nucleation driving force and induces TiB2 particle coarsening. This work provides new insights into liquid-phase in-situ reaction mechanisms and offers a novel, controllable route for fabricating high-performance micro/nano particle-reinforced metal matrix composites.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3801-1
Traditional phase transition gel platforms face significant challenges in achieving time-gated information encryption and decryption. Here, we report a photocleavable gel that enables time-gated information encryption and decryption, enhancing information storage security. The gel is synthesized by copolymerization of hydrophobic ortho-nitrobenzyl acrylate (NA) and acrylamide. Upon ultraviolet (UV) irradiation, hydrophobic NA units partially cleave to yield orange-colored o-nitrosobenzaldehyde (NSBA) molecules and hydrophilic acrylic acid groups, altering local color and hydrophilicity. Information is spatially encoded using a photomask. The written information is encrypted by dissolving NSBA molecules in dimethyl sulfoxide (DMSO). Upon aqueous immersion, differential hydrophilicity between irradiated and non-irradiated zones triggers localized phase separation, facilitating decryption. Notably, photolysis kinetics is time-gated, ensuring decryption only within a specific time window in water. This method surpasses traditional gel constraints, offering a novel paradigm for secure information storage.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3742-5
Nematic liquid crystal elastomers (NLCEs) exhibit excellent mechanical properties and diverse deformation modes, while cholesteric liquid crystal elastomers (CLCEs) as photonic crystals (PCs) possess superior optical performance and intelligent response characteristics. Combining these two elastomers into a monolithic material is a challenging yet promising endeavor. Here, we designed and synthesized a new diselenide-bonded molecule (DSeAc), whose lower bond energy between selenium atoms endows it with excellent bond exchange ability. Consequently, two LCE matrices containing DSeAc molecules can achieve seamless bonding under mild conditions via dynamic diselenide bond exchange. By integrating a CLCE film and an NLCE actuator into a monolithic film, we enable the integration of two functional components, whose functional characteristics can be tailored as required. This function block combination strategy offers a promising pathway for developing smart materials with complex functions, showing great potential in information storage, anti-counterfeiting, and biomimetics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3766-0
Leuco dye-based thermochromic fibers suffer from poor light fastness, limiting their cyclability. Here, a hydrogen bond dissociation/structural isomerization-based dual ultraviolet (UV)-shielding strategy is proposed to develop enhanced light-resistant thermochromic elastomer fibers (Azo/TCM@Abs/TPU) employing UV absorbers and 4-dodecyloxyazobenzene (C12-Azo) through a coaxial wet-spinning process. The integration of UV absorbers and C12-Azo enhances UV protection, effectively blocking nearly the entire UV spectrum. The light fastness of Azo/TCM@Abs/TPU has been improved to Grades 3–4, enabling a stable thermochromic function to withstand several months of sunlight exposure. Additionally, the absorbed UV light is stored as chemical energy within C12-Azo via trans-to-cis photoisomerization. This stored energy can be released as heat on demand. The coaxial dual-protection concept using photoisomerization offers an efficient method to enhance light resistance in thermochromic fibers.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3812-5
Anaerobic bacterial infections, prevalent in oxygen-deprived tissues, are recalcitrant to conventional antibiotics due to slow bacterial metabolism and the generation of nutrient-rich niches that foster polymicrobial biofilms. Propionibacterium acnes (P. acnes), a skin commensal, exemplifies this challenge, causing acne vulgaris and implant-associated infections, with rising antibiotic resistance. This study introduces an antimicrobial peptide (AMP), WRK (sequence: WRKFRRFKFRW-NH2), which induces endogenous reactive oxygen species (ROS) production in anaerobic bacteria, exploiting their inherent low ROS tolerance. WRK exhibited potent antibacterial activity, with a minimum inhibitory concentration (MIC) of 4 μg mL−1 against planktonic P. acnes and a minimum biofilm eradication concentration (MBEC) of 64 μg mL−1. To enable dermal delivery, WRK was encapsulated in layered dissolving microneedles (MNs), which demonstrated adequate mechanical strength for skin penetration. In a mouse back acne model, AMP MNs significantly reduced P. acnes infection and inflammation, outperforming commercial clindamycin gel. Histological analysis confirmed reduced inflammatory cell infiltration and tissue hyperplasia in the AMP MN group. This strategy offers a promising approach for treating anaerobic infections without promoting drug resistance, addressing a critical unmet need in clinical dermatology and implant surgery.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510039
The shipping industry's carbon emissions have drawn increasing attention. This study quantifies the carbon footprint of ship supply chains across their life cycle to identify key emission stages and reduction potentials, promoting green transformation. Based on life-cycle theory and using process analysis, a carbon footprint assessment model was constructed covering raw material acquisition, construction and assembly, transportation and distribution, and scrapping and recycling. The model was applied to a case ship, followed by multi-scenario and sensitivity analyses. Results show that the transportation and distribution stage is the dominant source of positive emissions, accounting for 88.73% of the total, while the scrapping and recycling stage provides a carbon offset benefit of 6.77%. Among five emission reduction scenarios—low-carbon materials, green energy, green logistics, circular economy, and comprehensive low-carbon—the reduction efficiencies are 2.02%, 0.06%, 18.44%, 0.42%, and 20.95%, respectively, indicating that green logistics is the core pathway for decarbonizing ship supply chains. Under the green logistics scenario, optimizing the LNG carbon emission factor yields more significant reduction effects. This study provides a life-cycle perspective on the carbon footprint structure of ship supply chains, offering theoretical references for identifying key reduction links and optimizing low-carbon technology pathways.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510018
Scientific assessment and prediction of the stabilization process in aged municipal solid waste (MSW) landfills are critical for reliable risk evaluation and remediation decision-making. Existing methods often fail under data-scarce conditions and lack temporal predictive capability. This study establishes a 'spatial characterization–temporal prediction' framework to address these gaps. The methodology integrates grid-based sampling, laboratory analysis of biological stability indicators (AT4), and LandGEM model simulations to assess current stabilization states and predict completion timelines. Applied to a landfill in southwest China, results reveal significant spatial heterogeneity in waste stabilization, strongly correlated with waste age and influenced by leachate recirculation of membrane concentrate. None of the landfill zones had reached full stabilization; predicted times to completion were: Zone D (17 years), Zone C (13 years), Zone B (8 years), and Zone A (1 year). Based on these findings, a systematic management strategy is proposed, including zoned gradient management, targeted control of lag zones, and dynamic planning. This study provides a theoretical basis for site-specific management and serves as a reference for similar landfills.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508101
The emission of sulfur dioxide (SO2) and nitrogen oxides (NOx) from fossil fuel combustion and metal smelting industries poses severe risks to environmental and human health. This study utilized depleted lead-zinc molten slag as a desulfurizer for wet flue gas desulfurization, and the resulting desulfurization slurry was further employed for NOx removal, achieving resource utilization. The desulfurization efficiency of the slag was determined, and NaClO2 was identified as the most effective oxidant when combined with the slag slurry for NOx removal. The effects of NaClO2 concentration, reaction temperature, flue gas flow rate, oxygen concentration, NOx concentration, and pH on removal efficiency were investigated. Optimal conditions were found at NaClO2 concentration of 2.5 mmol·L−1, temperature 45 °C, flue gas flow 200 mL·min−1, O2 volume fraction 10%, NOx volume fraction 0.03%, and pH 6, achieving a NOx removal efficiency of 97.24%. Metal ion experiments revealed that Fe3+, Zn2+, Mn2+, and K+ exhibited synergistic effects with NaClO2, with Fe3+ showing the most significant enhancement. Fe3+ promoted the decomposition of NaClO2 to generate stronger oxidants such as ClO2, thereby enhancing NOx oxidation and absorption. This approach offers a cost-effective and environmentally friendly alternative to traditional selective catalytic reduction, avoiding ammonia slip and secondary pollution.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025030302
A novel core-shell composite adsorbent, C18-SiO2@C, was synthesized for the determination of five phthalates in food samples. The adsorbent was prepared by assembling hexamethylcyclotrisiloxane (D3) into γ-cyclodextrin (γ-CD) cavities via saturated solution method, followed by hydrothermal oxidation to form SiO2@C, and subsequent C18 modification on the inner SiO2 core. The outer hydrophilic amorphous carbon shell enables effective extraction, while the inner C18 layer provides hydrophobic interactions. Using tip-based solid-phase microextraction (SPME), the adsorbent (10 mg) efficiently enriched phthalates from water, milk, and cola. Under optimized conditions (pH, eluent type/volume, sample volume, salt concentration), the method coupled with GC/MS exhibited linearity in the range of 0.5–10 ng·mL−1 (R² > 0.99), limits of detection (S/N ≥ 3) of 0.04–0.15 μg·L−1, and spiked recoveries of 74%–100% (RSD 1.32%–3.49%). For real samples, recoveries were 84.6%–102.3% for tap water, 80.7%–104.6% for cola, and 80.2%–101.4% for milk. The method offers simplicity, rapidity, low sample consumption, high enrichment efficiency, and strong matrix interference resistance, demonstrating significant potential for trace phthalate monitoring in foods.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025022704
Secondary inorganic aerosols (SNA), comprising sulfate, nitrate, and ammonium, are critical contributors to PM2.5 pollution in the Fenwei Plain, yet their formation mechanisms remain poorly characterized. Wintertime observations in Taiyuan revealed SNA as the dominant PM2.5 component, with a mean mass concentration of 33.19 ± 18.72 μg m−3, accounting for 47.13% of total PM2.5 mass. SNA concentrations increased markedly with pollution severity, but even under relatively clean conditions, SNA maintained a high mass fraction. Diurnal variation and correlation analyses indicated that nitrate formation pathways differed between day and night, largely governed by relative humidity (RH). During daytime, high RH (>55%) facilitated the partitioning of gaseous HNO3 to particulate nitrate. At night, RH positively correlated with nitrate concentration and nitrogen oxidation rate (NOR), with increased aerosol liquid water content (AWC) promoting NO2-to-nitrate conversion. The PM2.5 pH ranged from 4.3 to 5.2, and sulfate formation was primarily driven by H2O2 oxidation, with NO2 oxidation as a secondary pathway. These findings enhance understanding of SNA formation in the Fenwei Plain and provide a scientific basis for air quality policy.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606013
The A2/O-MBR process, owing to its superior effluent quality and smaller footprint, is increasingly adopted in newly built and upgraded wastewater treatment plants. However, systematic studies on its greenhouse gas (GHG) emissions remain scarce, and direct comparisons with the conventional A2/O process are lacking. In this study, two full-scale wastewater treatment plants employing the A2/O and A2/O-MBR processes under identical influent conditions, climate, and discharge standards were investigated. A high-frequency monitoring system covering the entire treatment train was established, and combined with measurements of dissolved CH4 and N2O, water quality parameters, and operational parameters, to elucidate the differences in GHG emission characteristics. Results showed that the daily average CH4 emission intensities were not significantly different between the two plants [(0.67 ± 0.22) and (0.65 ± 0.18) g/m3, respectively]. CH4 emissions mainly originated from sewer-derived anaerobic production and subsequent release in the pretreatment units (accounting for over 70% of the total emissions), with partial in-plant oxidation by methanotrophs. Temperature and aeration-induced stripping were identified as key driving factors, as CH4 emissions were positively correlated with ambient temperature and dissolved oxygen (DO). In contrast, more than 90% of N2O emissions occurred in the biological treatment units. The A2/O-MBR plant exhibited significantly higher daily N2O emission intensity [(0.132 ± 0.055) g/m3] than the A2/O plant [(0.060 ± 0.046) g/m3], largely due to intensive aeration and oxygen-enriched internal/external recirculation in the membrane tank, which enhanced N2O production and stripping. Correlation analysis further revealed that N2O emissions in the A2/O plant were positively related to influent COD and BOD5, indicating dominance of heterotrophic denitrification, whereas in the A2/O-MBR process they were mainly driven by NH3-N loading and DO, reflecting a nitrification-based pathway. Importantly, both processes exhibited CH4 and N2O emission factors that were significantly lower than the reference values recommended by the IPCC and industry guidelines, underscoring the necessity of localizing emission factors for accurate carbon accounting.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606019
Sludge co-combustion in coal-fired power plants generates flue gas dust with high viscosity, causing severe dust deposition on downstream environmental protection equipment. This study analyzed the dust deposition mechanism in electrostatic precipitators (ESPs) and characterized the dust layer properties. Results indicated that sludge co-combustion increased flue gas moisture content, altered particle morphology, and elevated dust viscosity. To address these issues, an anode pneumatically rapped ESP technology was developed to enhance anode plate cleaning. This technology was retrofitted on a 1000 MW unit at Zhejiang Jiahua Power Plant, and performance tests under sludge co-combustion conditions were completed in February 2025. At a specific dust collection area of 118 m²·s/m³ and a unit load of 987 MW, the ESP outlet dust concentration decreased from 25.32 mg/m³ before retrofit to 7.95 mg/m³ after retrofit. Analysis revealed that sludge co-combustion caused excessive dust deposition on the first electric field anode plates, inducing back corona, high-voltage power supply flashover, and low secondary voltage and current. After retrofit, regions with low rapping acceleration were eliminated, achieving effective dust cleaning. Secondary voltage and current were significantly improved, and overall ESP efficiency was remarkably enhanced. The proposed technology provides a reference for ESP retrofitting of coal-fired units under biomass (sludge) co-combustion and low-load conditions.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3870-9
High-purity (HP) alloys are critical for next-generation technologies requiring extreme reliability, yet trace impurities at parts-per-million levels can severely degrade mechanical properties, corrosion resistance, and long-term stability. This review comprehensively examines recent advances in HP alloy development, covering purification approaches, processing strategies, and performance optimization. It details how trace impurities influence microstructural evolution and material properties, and discusses techniques for achieving ultralow impurity levels, including vacuum melting, zone refining, and chemical vapor deposition. The review highlights impurity sensitivity across major alloy systems—such as aluminum, titanium, zirconium, copper, and steels—and summarizes strategies to mitigate impurity-induced degradation, including advanced alloy design, grain refinement, and surface treatments. Advanced characterization techniques for detecting and quantifying impurities are also outlined. The review emphasizes the essential role of HP alloys in advanced structural and functional materials, and identifies key challenges and future directions, including the need for standardized purity definitions and cost-effective purification methods. This synthesis provides a roadmap for researchers and engineers aiming to harness the full potential of high-purity alloys in demanding applications.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606017
Against the backdrop of global green transition and tightening resource constraints, China's Dual Carbon Goals and Zero-Waste City initiative have positioned waste valorization as a critical pathway for sustainable development. Zinc, a fundamental metal, faces high external dependence and nearing primary resource limits, making the regenerated zinc industry essential. However, the previous standard YS/T 1093-2015 lagged in classification, technical indicators, and environmental requirements. This paper analyzes the revision to YS/T 1093-2024, which renames the standard to 'Recycled Zinc Raw Materials' and clarifies its role as front-end smelting intermediate feedstock. The new standard establishes a classification system covering six typical zinc-bearing materials, expanding utilization of low-grade complex materials (zinc content 5%-15%). It tightens limits on harmful elements (fluorine, chlorine, lead, arsenic) and introduces moisture control and appearance evaluation indicators, enhancing operability and environmental risk control. Compared with EU standards, it shows systematic improvements in raw material coverage, process adaptability, and environmental risk prevention. The revision is expected to drive the regenerated zinc industry toward intensification, high-value utilization, and clean production, improving resource recycling efficiency and supporting China's zinc resource strategic security and low-carbon development.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3929-4
Hydrogels are extensively utilized in biomedical fields such as drug delivery, tissue engineering, and wound dressings due to their excellent biocompatibility, high water content, and tunable physicochemical properties. However, conventional hydrogels often undergo uncontrolled swelling in physiological environments, leading to mechanical degradation, structural destabilization, and functional failure, which severely restricts their long-term applicability. Recent advances have focused on developing anti-swelling hydrogels with equilibrium swelling ratios typically below 150%, achieved through strategies including the introduction of hydrophobic interactions, enhancement of cross-linking density, and incorporation of nanocomposite structures. These approaches significantly improve dimensional stability and mechanical integrity under physiological conditions. This review systematically summarizes the common preparation strategies for anti-swelling hydrogels and highlights their latest progress in biomedical applications, including wound dressings, tissue adhesives, and implantable devices. The advantages and future directions, such as smart responsiveness and multifunctional integration, are critically discussed. The review aims to provide theoretical guidance and technical references for the development of next-generation high-performance medical hydrogel materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3858-8
High-quality β-Ga2O3 membranes are pivotal for fabricating high-performance memristive devices. Here, vertical Ag/β-Ga2O3/Pt memristors built on high-crystalline-quality β-Ga2O3 membranes via lattice epitaxy engineering and a sacrificial-layer-assisted exfoliation strategy are reported. The resulting β-Ga2O3-based device demonstrates a high ON/OFF ratio exceeding 10^8, low SET/RESET voltages of 0.13 V/−0.11 V, low programming current of 10^-10 A, stable data retention beyond 4 × 10^4 s, and excellent subthreshold characteristics of ~0.47 mV/dec. Adjustable compliance current enables the coexistence of volatile and non-volatile switching modes. Additionally, the resistive switching versatility is predominantly governed by the migration of Ag ions, as supported by electrical characterizations and first-principles calculations. Furthermore, a β-Ga2O3 memristor-based circuit that functions as a reconfigurable and non-volatile exclusive OR (XOR) logic gate has been designed and simulated, enabling both image encryption/decryption and edge detection. This work not only demonstrates lattice-engineered, high-quality β-Ga2O3 membranes for fabricating advanced memristors but also extends their applicability to digital logic and reconfigurable image processing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4140-9
Metal covalent organic frameworks (MCOFs) are promising photocatalysts for carbon dioxide reduction reaction (CO2RR). However, the synthesis of ketimine-linked COFs remains challenging due to the low reactivity of ketones. Here, we report a straightforward strategy to construct diketimine-linked MCOFs via the condensation of acenaphthenequinone (Ace) with 1,3,6,8-tetra(4-aminophenyl)pyrene (TAPPy). The metal-free COF (TACOF-AA) exhibits AA stacking, while the addition of NiCl2·6H2O under identical conditions yields an AB-stacked Ni-based MCOF (Ni-TACOF-AB). The coordinated Ni species serve as active sites for CO2RR and enhance electron-hole separation. Photocatalytic tests demonstrate that Ni-TACOF-AB achieves a CO evolution rate of 11.71 mmol g−1 h−1 with 99.9% selectivity, which is 7.6 times higher than that of TACOF-AA. Density functional theory (DFT) calculations reveal that Ni-TACOF-AB lowers the activation energy barrier of the rate-determining step by regulating local charge distribution, facilitating electron transfer to adsorbed CO2. This work provides a novel approach for synthesizing ketimine-based COFs and highlights the importance of interlayer stacking in modulating photocatalytic performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3862-x
Hexagonal boron nitride (hBN) is indispensable for next-generation electronics and quantum technologies, yet controlled synthesis of isotopically engineered hBN with macroscopic scalability and atomic-level precision remains challenging. Here, we present a plasma-enhanced chemical vapor deposition (PECVD) method using elemental boron (B) and nitrogen (N) precursors to achieve wafer-scale growth and precise isotopic control of hBN films. High-quality hBN films are synthesized on Cu substrates via optimized B evaporation and N2 plasma activation. The growth mechanism involves an oxygen-mediated pathway for B transport and a layer-by-layer (Frank-van der Merwe) mode for multilayer formation. By employing isotopically enriched B powders (10B and 11B) and N2 gases (14N2 and 15N2), we demonstrate tunable isotopic compositions with phonon mode shifts quantitatively matching harmonic oscillator predictions. Furthermore, we realize unprecedented in-plane h10BN-h11BN heterostructures through dynamic B source switching during growth. This PECVD strategy establishes a transformative synthesis platform merging industrial-scale production capacity with atomic-scale isotopic precision, enabling new opportunities to engineer thermal transport, optical response, and quantum coherence in two-dimensional materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3787-x
Circumventing the tumor's defensive antioxidant system and achieving precision cancer therapy remain major challenges in high-efficacy tumor treatments. Here, we propose a synergistic strategy integrating non-oxidative physical ablation and oxidative chemical intervention. An acid-responsive self-collapsing nanomineral PCSB is constructed, comprising poly(acrylic acid)-modified calcium sulfite (CaSO3) and a pH-responsive photoacoustic (PA) therapeutic molecule, aza-BDP. In the tumor acidic microenvironment, PCSB decomposes, releasing PA agents and SO2/Ca2+, thereby enabling combined non-oxidative mechanical damage from PA therapy and oxidative chemical damage from SO2 gas and Ca2+ ions. This dual-action approach effectively reduces resistance conferred by tumor antioxidant mechanisms and improves treatment precision. The study presents a synergistic physical-chemical strategy with significant potential for solid tumor elimination.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3976-x
The discovery of high-temperature superconductivity in bilayer nickelate La3Ni2O7−δ (La-327) under high pressure and in thin films at ambient pressure has opened new avenues in superconductivity research. However, La-327 exhibits a narrow phase stability range, leading to stacking faults that suppress bulk superconductivity. Chemical substitutions, particularly at the A-site with smaller rare-earth ions, have been shown to enhance phase purity and reduce stacking faults, while also increasing the orthorhombic distortion and chemical pressure. In this work, we apply the high-entropy (HE) strategy to stabilize the 327 phase with reduced average A-site ionic radius (rA). We successfully synthesized medium-entropy La1.2Pr0.6Nd0.6Sm0.6Ni2O7−δ (ME-327) and high-entropy La0.67Pr0.67Nd0.67Sm0.33Eu0.33Gd0.33Ni2O7−δ (HE-327) polycrystalline samples. These compositions satisfy medium- and high-entropy criteria, with rA values of 1.181 Å and 1.164 Å, respectively. The samples are phase-pure and homogeneous. HE-327 exhibits the lowest cell volume, largest orthorhombicity, and shortest interlayer Ni-Ni distance among reported bilayer nickelates. Physical property measurements reveal low electrical conductivity and a high density-wave (DW) transition temperature. Under high pressure, HE-327 shows a resistivity anomaly at 103 K under 31 GPa, suggesting a possible superconducting transition. Extrapolation indicates that Tc under high pressure exceeds 100 K for HE-327, correlating with reduced rA and enhanced interlayer coupling. Our results demonstrate the ionic size effect and the effectiveness of the HE approach in stabilizing bilayer nickelates, providing a new avenue for developing superconducting materials.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511003
Tailings dam leakage can cause secondary sudden water pollution events, imposing severe combined stress of high turbidity and heavy metal contamination on natural water bodies within a short period, threatening aquatic ecological security. Existing studies have systematically revealed the pollution characteristics and biological effects of such events, which are fundamentally distinct from natural high-turbidity water and industrial wastewater leakage. Compared with natural high-turbidity water, tailings leakage inputs finer particles with higher specific surface area, leading to more intense and prolonged turbidity stress. Meanwhile, heavy metals in tailings are more enriched than natural sediments, with higher proportions of active forms and bioavailability, causing significant bioaccumulation and toxic effects, and long-term decline in benthic community species richness. Compared with industrial wastewater leakage, tailings leakage simultaneously releases high concentrations of fine suspended solids and multiple heavy metals, forming a unique 'physical-chemical' combined stress. This synergistic effect amplifies biological toxicity through multiple pathways such as mechanical damage, light limitation, and oxidative stress, resulting in severe and often irreversible ecological damage, such as impaired fish swimming behavior and collapse of benthic community structure. Analyzing the long-term impacts of tailings leakage on aquatic ecosystems from the perspective of combined stress is helpful for providing scientific basis for emergency response and medium-to-long-term ecological risk prevention of related sudden water pollution events.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510034
Phosphonate wastewater, characterized by stable C–P bonds, poses significant environmental risks due to its resistance to degradation and potential to contribute to eutrophication. This study developed a chloride-enhanced Fe(II)/PMS/H2O2 system for the oxidative degradation of 2-phosphonobutane-1,2,4-tricarboxylic acid (PBTC) and simultaneous recovery of phosphorus as iron phosphate (FePO4). Under optimal conditions (0.1 mmol/L PBTC, 1.0 mmol/L Fe(II), 0.5 mmol/L PMS, 0.5 mmol/L H2O2, 10 mmol/L NaCl, initial pH 3.0, 60 min), total phosphorus (TP) removal reached 100%, with phosphorus nearly completely recovered as FePO4 precipitate. Increasing NaCl concentration and temperature enhanced TP removal, while pH significantly influenced removal efficiency and product speciation; acidic conditions (pH < 4.3) favored FePO4 precipitation. Coexisting Ca2+ and Mg2+ had negligible effects, whereas HCO3− and humic acid (HA) inhibited TP removal in a concentration-dependent manner. Radical quenching and electron spin resonance (ESR) analyses identified hydroxyl radicals (•OH), ferryl ion (Fe(IV)=O), sulfate radicals (SO4•−), and chlorine radicals (Cl•) as primary reactive species, with •OH playing a dominant role. Chloride introduction promoted the generation of multiple reactive species, and Cl• and its derivative Cl2•− directly attacked the C–P bond and phosphonate group, facilitating phosphorus release as PO43− and subsequent FePO4 formation. The system's feasibility was validated using actual industrial circulating cooling water. This study provides a novel approach for phosphonate wastewater treatment and phosphorus recovery.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511057
To investigate the effects of applying sewage sludge aerobic fermentation products on antibiotic resistance genes (ARGs) in the rhizosphere soil and phyllosphere of pakchoi (Brassica chinensis L.), field experiments were conducted with three treatments: sludge product (sludge group), chemical fertilizer (fertilizer group), and no fertilizer (control). Antibiotic residues, abundances of ARGs and mobile genetic elements (MGEs) were measured in rhizosphere soil and phyllosphere, and microbial community composition and virulence factor (VF) contributions were annotated via metagenomics. Results showed that antibiotic concentrations in rhizosphere soil were generally higher than in phyllosphere. Compared with control, sludge application increased soil antibiotic content by 12.70%, whereas fertilizer increased it by only ~3%, indicating a more significant exogenous input from sludge. At the resistance level, total ARG abundances in rhizosphere soil and phyllosphere of the sludge group increased by 25.47% and 73.08%, respectively, relative to control, with concurrent increases in beta-lactam resistance genes and MGEs such as integron intI1. Sludge application may enhance integron-mediated gene capture and horizontal transfer potential, driving resistance risk accumulation in both phyllosphere and rhizosphere soil. Conversely, fertilizer application reduced ARG abundances by 53.40% in rhizosphere soil and 13.50% in phyllosphere compared with control, consistent with decreased microbial community abundance and diversity, suggesting that reduction of host bacteria and dissemination vectors was a key reason. In community structure, Proteobacteria dominated the phyllosphere, while Chloroflexi dominated rhizosphere soil. Correlation networks identified Sphaerobacter thermophilus and Aggregatilinea lenta positively correlated with multiple ARGs (r≈0.95–1.00), whereas Solirubrobacter sp. CPCC_204708 was negatively correlated (r≈−0.91). Virulence factor contributions followed trends similar to ARGs. Sludge fermentation products simultaneously increased ARG prevalence and related risk indicators in both rhizosphere soil and phyllosphere of pakchoi, providing a reference for risk identification and safe application of sludge fermentation products in agriculture.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60639-1
Ni/Al2O3 is regarded as one of the most promising catalysts for industrial CO2 methanation, yet it suffers from inadequate low-temperature activity and thermal sintering. To address these challenges, an Ni/CaO-ZrO2-Al2O3 catalyst with high low-temperature activity and robust high-temperature sintering resistance was developed by introducing Ca and Zr promoters. Under reaction conditions of 250 °C and a space velocity of 30000 mL/(g·h), the catalyst achieved a CO2 conversion of 96% and a methane space-time yield of 257.5 mmol/(g·h). In a 200 h aging test at 600 °C, the Ca-Zr dual-promoted catalyst exhibited a smaller increase in Ni particle size and less activity loss compared to the Ca-promoted counterpart. Characterization revealed that Ca and Zr promoters not only improve Ni dispersion but also enhance surface basicity, contributing to excellent low-temperature activity. Furthermore, Zr suppresses the transformation of Ca species into CaCO3 via solid-phase reaction under operating conditions, thereby inhibiting Ni sintering and ensuring high-temperature stability. This work provides a novel promoter design strategy for developing high-performance Ni-based catalysts for CO2 methanation.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025031901
The rapid expansion of the nuclear power industry has increased the demand for effective nuclear wastewater treatment, making the efficient removal of radioactive iodine isotopes (e.g., 131I, 129I) from aqueous environments a critical challenge. Covalent organic frameworks (COFs), a class of crystalline porous materials characterized by high specific surface area, tunable pore structures, and exceptional stability, exhibit significant potential for capturing radioactive iodine from water. This review systematically examines the adsorption mechanisms of iodine by COF materials, including electrostatic interactions, charge transfer, hydrogen bonding, and secondary mechanisms such as metal coordination, ion exchange, and van der Waals forces. The effects of COF pore structures on iodine removal efficacy are discussed with a focus on pore size and functional group modifications. Key research trends and prevailing challenges in the application of COFs for aqueous iodine capture are analyzed, including the need for selective adsorption in complex wastewater matrices and the scalability of COF synthesis. The review concludes with a perspective on future research directions, emphasizing the design of novel COFs with tailored pore chemistry and the development of cost-effective, regenerable adsorbents for practical deployment in nuclear wastewater treatment.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026022502
This study investigates the effects of different land use types on topsoil carbon (C) and nitrogen (N) contents and their spatial distribution in the lower reaches of the Sancha River Basin, a karst region of the Yunnan-Guizhou Plateau. Grid sampling collected 0–20 cm topsoil from forestland (n=23), cultivated land (n=25), and grassland (n=32). Total C and N were measured. Results showed that topsoil C content followed grassland (40.36±22.92 g·kg−1) > forestland (37.05±12.83 g·kg−1) > cultivated land (34.06±14.57 g·kg−1), while N content followed forestland (2.89±0.76 g·kg−1) > grassland (2.67±1.19 g·kg−1) > cultivated land (2.50±0.65 g·kg−1). One-way ANOVA revealed no significant differences among land use types (P>0.05). Soil C and N were significantly positively correlated across all land uses (r>0.5, P<0.001). Coefficient of variation (CV) indicated grassland had the highest C variability (0.57), while forestland showed the most stable C and N (CV=0.35 and 0.26, respectively). Cultivated land had CVs of 0.43 for C and 0.26 for N. Spatially, forestland exhibited concentrated high C values with significant N heterogeneity; grassland had higher C in southern and eastern areas but scattered distribution, with generally low and variable N; cultivated land showed uniform but lowest C and N. Land use types significantly drive topsoil C and N dynamics through vegetation input, soil disturbance, and management practices, underscoring the importance of rational land use planning for enhancing carbon sink functions and sustainable development in karst watersheds.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607006
This study evaluates the global warming potential (GWP) of three typical air pollution control device (APCD) configurations in municipal solid waste (MSW) incineration under ultra-low emission standards. The configurations are APCD1 (SNCR+SDS+DS+ACI+FF), APCD2 (SNCR+SDS+DS+ACI+FF+SCR+WS), and APCD3 (SNCR+SDS+DS+ACI+FF+WS+SCR). Life cycle assessment (LCA) was applied to quantify GWP. Results indicate that APCD3 exhibits the highest GWP due to increased electricity consumption, yet it achieves the lowest pollutant emissions among the three. APCD1 shows the highest NOx emissions, contributing significantly to GWP, and requires technological upgrades. APCD2 consumes more resources but does not proportionally reduce emissions, suggesting inefficiencies. Electricity consumption is the dominant factor influencing GWP across all processes; reducing electricity use and improving energy efficiency are critical for mitigating environmental impact. The study recommends further research on CO2 reduction strategies and adoption of more efficient DeNOx technologies to align MSW incineration with ultra-low emission and low-carbon goals.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3875-1
Photocatalytic hydrogen evolution reaction (HER) from pure water is a promising strategy to address critical challenges in energy sustainability and environmental remediation. However, HER over single-component photocatalysts is intrinsically limited by inefficient carrier separation and relatively poor photostability. Forming abundant interfaces between two components is an effective approach for solving these issues. Herein, a series of hierarchical core-shell heterojunction photocatalysts, designated as F@Z-X, was rationally constructed by in situ growing ZnIn2S4 (ZIS) nanosheets on a Ti-based metal-organic framework (FIR-125), demonstrating remarkable structural stability. Due to the abundant intimate contact interfaces and well-matched band structure, the F@Z-X series exhibit enhanced HER performance. Among them, the optimized heterojunction [email protected] shows a photocatalytic hydrogen evolution rate of 3789.45 μmol g−1 h−1, which is about 4.4 and 264.4 times higher than that of pristine ZIS (859.57 μmol g−1 h−1) and FIR-125 (15.32 μmol g−1 h−1), respectively. Moreover, the photocatalyst manifests excellent reusability and durability, maintaining its performance over five consecutive cycles and sixteen hours of continuous reaction. The outstanding performance of [email protected] may be ascribed to an optimal balance among three fundamental photocatalytic processes: sufficient light absorption, exceptional carrier separation, and appropriate surface reaction. This work offers valuable insights into the rational design and controllable synthesis of novel heterojunction photocatalysts for efficient hydrogen evolution.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3920-1
Lead-free halide perovskites are promising scintillators due to strong X-ray attenuation and high internal quantum efficiency (IQE), but their application is hindered by moisture sensitivity. Here, CsSrCl3:Eu2+ nanocrystals were grown in situ in a specially designed inorganic glass matrix. By employing [PO4]-modification and controlled crystallization, a transparent CsSrCl3:Eu2+ glass-ceramic (GC) scintillator was obtained, combining high crystallinity (15.9%) with excellent optical transparency (85.3% at 432 nm). The GC exhibits outstanding photoluminescence (PL) performance, including a high IQE of 87.6% and superior thermal stability (74% intensity retention at 493 K relative to 303 K). Benefiting from the robust glass matrix, the GC retains 99% of its initial PL intensity after 14 days of water immersion. Under X-ray excitation, it shows blue X-ray excited luminescence (XEL), with peak and integrated intensities reaching 117% and 25.1% of those of Bi4Ge3O12 crystal, respectively. The scintillator achieves a high spatial resolution of 20 lp mm−1 and an X-ray detection limit of 3.7 μGy s−1. Furthermore, it demonstrates exceptional operational stability in humid environments, maintaining clear X-ray image contrast even after 48 h of water submersion. This study provides an effective strategy for stabilizing hygroscopic halide scintillators in a durable [PO4]-modified fluoroaluminate glass matrix and demonstrates the potential of CsSrCl3:Eu2+ GC for high-resolution and stable X-ray imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3825-x
Polymer-based dielectric materials with high energy density and thermal stability are critical for modern electric/electronic industries. Polyimide (PI) based materials are promising due to their high temperature resistance and chemical inertness, yet their inherently low dielectric constant and limited charge-discharge energy density restrict applications in film capacitors. While incorporating ferroelectric or conductive fillers can enhance dielectric performance, batch-to-batch inconsistency and physical deterioration remain problematic. This study focuses on molecular structure design and modulation, preparing hyperbranched polyimides with different dianhydride monomers and branching degrees. The effects of chain packing density with polar groups on dielectric and energy storage performances were systematically investigated via experimentation and molecular simulation. Results demonstrate a significant correlation between monomers' electrical distribution and packing density in polymer systems. Molecular simulation further elucidated the underlying mechanism. This work establishes a foundation for designing polymer-based dielectric materials with high dielectric and energy storage performances at the molecular level.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3964-5
The escalating demand for personalized thermal-moisture comfort, coupled with the high energy consumption of conventional heating and cooling systems and the imperative for low-carbon energy conservation, has driven the development of shape memory smart fabrics that respond to environmental changes. However, existing shape memory thermal-moisture management fabrics suffer from excessively high response temperatures, inadequate response performance, and suboptimal thermal-moisture management. In this work, a dual-network shape memory polymer (SMP) was synthesized, and its shape memory transition temperature was tuned to align with the human thermal comfort range. The polymer was processed into fibers and subsequently into twisted-coiled artificial muscles to enhance reversible strain. Woven with wool into a plain fabric, the resulting textile exhibits adaptive thermal-moisture management, achieving a warp reversible strain of up to 17.5%. At elevated temperatures, the fabric contracts, exhibiting an air permeability of 1546 mm/s and thermal conductivity of 0.0518 W/(m·K); at lower temperatures, it elongates, with air permeability of 1322 mm/s and thermal conductivity of 0.0426 W/(m·K), thereby realizing 'warm when cool and cool when hot' functionality. Compared with commercial wool fabrics, this smart fabric lowers the skin microenvironment temperature by 1.5 °C and offers an energy savings potential of approximately 222.58 MJ/m² per year in capital cities such as Beijing. This work provides a novel technical pathway and design approach for future personalized comfort and low-carbon, energy-saving textiles.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4079-4
Utilization of ultrahigh-nickel LiNi_xCo_yMn_1-x-yO_2 (NCM) (x > 0.97) in Li-ion batteries can distinctively boost energy density through enhanced discharge capacity. However, capacity and thermal stability deteriorate as Ni content approaches the limit. Here, we propose a facile strategy by introducing high-valence tungsten (W) into ultrahigh-nickel polycrystalline LiNi_0.98Co_0.01Mn_0.01O_2 (PCNCM98). W-doped PCNCM98 (W-PCNCM98) exhibits refined, compactly stacked primary particles, whereas PCNCM98 shows equiaxial, non-uniform larger particles. The refined microstructure enhances mechanical strength: average particle hardness of W-PCNCM98 is 104 MPa, 1.5 times higher than PCNCM98 (68 MPa). This improved mechanical property suppresses lattice volume changes and relieves microcrack formation from H2–H3 phase transition. Consequently, cycling performance in pouch-type full cells is significantly enhanced, with capacity retention of 73% after 2000 cycles at 1 C and 25 °C, 54% higher than PCNCM98. Enhanced structural stability and strong electron affinity of W6+ also improve thermal stability: exothermic peak for W-PCNCM98 is postponed to 203 °C with heat generation of 1287 J g−1, versus 190 °C and 1528 J g−1 for PCNCM98. This high-valent doping strategy stabilizes ultrahigh-nickel NCM cathodes, accelerating large-scale EV applications.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508006
Landfill leachate, characterized by high ammonia nitrogen, high organic load, complex toxic components, and low nitrogen removal efficiency, poses significant environmental challenges. To achieve efficient nitrogen removal, a continuous-flow two-stage anoxic/oxic (A/O) moving-bed biofilm reactor (MBBR) system coupled with anaerobic ammonium oxidation (Anammox) was constructed and operated for long-term treatment of actual landfill leachate. After biofilm attachment and multi-gradient acclimation, influent concentrations were gradually increased from low levels (NH4+-N ~200 mg·L−1, COD ~2500–3000 mg·L−1) to high levels (NH4+-N ~1800 mg·L−1, COD ~8500 mg·L−1). During stable operation, average removal efficiencies of NH4+-N and COD reached 97.7% and 66.8%, respectively, with total nitrogen (TN) removal efficiency improving to 93.9%. Along the reactor, the first A/O stage achieved major organic degradation and ammonia oxidation, while the second stage facilitated nitrite accumulation and promoted Anammox for synergistic nitrogen removal. High-throughput sequencing revealed Proteobacteria as the dominant phylum (>50%), with denitrifying genera such as Azoarcus and Thauera significantly enriched. Planctomycetota abundance increased from 0.6% to 3.7%, and Candidatus Kuenenia was detected, confirming successful Anammox colonization and participation in nitrogen removal. This study validates the efficient combined nitrogen removal mechanism of the A/O–MBBR system with Anammox, providing theoretical basis and technical support for engineering treatment of high-ammonia wastewater.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512015
The co-contamination of cadmium (Cd), lead (Pb), and zinc (Zn) in agricultural soils near mining areas poses significant risks to ecosystems and human health. Conventional stabilization materials often exhibit insufficient performance for Zn, particularly in multi-metal systems. This study synthesized a novel composite biochar (PFMBC) by loading phosphate and iron-manganese oxides onto biochar via phosphoric acid impregnation followed by secondary pyrolysis at 600 °C. The stabilization efficiency of PFMBC was evaluated against pristine biochar (BC) and iron-manganese modified biochar (FMBC) in a soil collected from a lead-zinc mining area (total Cd: 43.77 mg·kg−1, Pb: 3355.94 mg·kg−1, Zn: 1296.57 mg·kg−1). After 60 days of incubation with 5% PFMBC, the DTPA-extractable (bioavailable) fractions of Cd, Pb, and Zn decreased by 73.44%, 90.10%, and 69.33%, respectively, significantly outperforming BC and FMBC. Sequential extraction indicated that PFMBC promoted the transformation of Cd, Pb, and Zn from acid-soluble and reducible fractions to more stable residual fractions. Characterization via FTIR, SEM, and XRD revealed enhanced surface functional groups and the formation of stable mineral phases. The synergistic effects of phosphate precipitation, iron-manganese oxide adsorption, and surface complexation contributed to the superior stabilization, particularly overcoming the challenge of Zn immobilization. These findings demonstrate that PFMBC is a promising amendment for the remediation of Cd-Pb-Zn co-contaminated soils, offering high efficiency and long-term stability.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509120
The 'Zero-Waste City' initiative, centered on source reduction, resource utilization, and safe disposal of solid waste, aims to minimize environmental impact. To quantitatively assess its carbon reduction contribution, this study took Mianyang as a case, systematically collecting data on solid waste generation, utilization, and disposal across industrial, agricultural, and other sectors from 2021 to 2024. Employing an improved WARM model and emission factor method, and incorporating generation, utilization, and disposal intensities, the carbon reduction benefits before (2021–2022) and after (2023–2024) the initiative were evaluated. Results show that despite significant improvements in comprehensive utilization and safe disposal rates, total solid waste generation increased, leading to a net negative carbon effect of -127.6×10^4 tCO2eq based on absolute quantities. However, after stripping economic and population growth factors, intensity-based accounting revealed a cumulative reduction of 10.8×10^4 tCO2eq, demonstrating significant synergistic benefits. The industrial sector contributed the most, with a reduction of 40.2×10^4 tCO2eq, driven by green transformation and enhanced utilization capacity. Conversely, the rising intensity of domestic solid waste generation resulted in a negative benefit of -46.1×10^4 tCO2eq, highlighting a key area for future improvement. The study underscores the necessity of considering both intensity and absolute quantity dimensions in evaluating rapidly developing cities. These findings provide practical evidence and reference pathways for advancing 'Zero-Waste City' construction and synergistic pollution reduction and carbon mitigation under the 'dual carbon' goals.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511050
Municipal solid waste (MSW) management in Inner Mongolia has long relied on landfilling, facing land scarcity and leachate management challenges. This study addresses the region's dry, cold climate, high proportion of agricultural and livestock waste, fluctuating moisture content, and weak leachate treatment capacity. An engineering optimization was implemented on an 80 t·d−1 vertical rotary gasification-incineration system featuring a dual-combustion-chamber design (primary chamber for medium-temperature pyrolysis-gasification at 550–650 °C and secondary chamber for high-temperature oxidation above 900 °C), coupled with in-situ leachate recirculation. Field measurements showed improved processing capacity and continuous operation stability. Under the project's leachate yield, in-situ recirculation achieved on-site disposal without significant adverse effects on gasification-incineration conditions, providing buffering against moisture fluctuations. During the monitoring period, major gaseous pollutant emissions remained below current national standards. The results provide engineering references for the co-processing and stable operation of small-scale county-level MSW treatment facilities.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60677-9
Mg-, Ca-, Sr-, and Ba-single-doped La2O3 as well as Mg-Ba co-doped La2O3 catalysts were synthesized via a hydrothermal method and evaluated for the oxidative coupling of methane (OCM). The experimental results revealed that the Mg-modified La2O3 catalyst activates O2 and CH4 effectively, yet achieves only moderate C2+ selectivity. Conversely, the Ba-modified analogue affords high C2+ selectivity, albeit at the expense of lower reaction activity. Notably, the Mg-Ba co-doped La2O3 catalyst strikes an effective balance between activity and selectivity, enhancing catalytic performance while maintaining a high C2+ selectivity. Specifically, at a Mg/Ba molar ratio of 1:1 and 700 °C, it achieved a CH4 conversion of 29.5%, a C2+ selectivity of 54.5% and a corresponding C2+ yield of 16.1%. The characterization results indicate that Mg and Ba co-doped La2O3 catalysts promote the formation of more superoxide (O2−) species on the catalyst surface, which in turn significantly enhances both the activity and selectivity of La2O3 catalysts. In situ DRIFTS revealed the presence of superoxide species on the surface of both Mg- and Ba-doped catalysts, with the co-doped system exhibiting a significantly more intense signal for the superoxide species. O2/H2-TPR studies revealed that Mg and Ba co-doped La2O3 catalysts exhibit superior O2 activation capabilities compared to those doped with Mg or Ba alone. CH4/O2 pulse experiments revealed that the co-doped catalysts facilitate faster establishment of oxygen adsorption equilibrium, thereby enhancing CH4 activation and the subsequent formation of C2 products. This work establishes that co-doping La2O3 with Mg and Ba represents an effective strategy for improving catalytic performance in OCM, primarily by modulating the generation and stabilization of key active oxygen species.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2026.JFCT.0003
Phosphorus and transition metal-modified ZSM-5 zeolites were prepared via incipient wetness impregnation and characterized by XRD, N2 adsorption-desorption, and pyridine-IR spectroscopy. The effects of modified zeolites on catalytic pyrolysis of n-heptane, 3-methylhexane, and methylcyclohexane were systematically investigated, revealing the structure-activity relationship between acid properties and catalytic performance. Results indicate that phosphorus and transition metal modification can regulate the L/B acid ratio of ZSM-5, which significantly influences product distribution. An excessively high L/B acid ratio promotes hydrogen and coke formation, leading to pore blockage and reduced conversion, whereas an appropriate L/B acid ratio facilitates mild dehydrogenation, enhancing ethylene and propylene yields. Reactant conversion followed the order: n-heptane > 3-methylhexane > methylcyclohexane. Efficient conversion of 3-methylhexane and methylcyclohexane requires catalysts with high L acid amount, strong Brønsted acid amount, optimized L/B acid ratio, as well as high specific surface area and micropore specific surface area. This study provides critical insights for designing high-efficiency alkane pyrolysis catalysts.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042304
To characterize the spatial variability of PM2.5 chemical components at the urban scale, ambient PM2.5 samples were collected from eight sites across Changsha, China. Samples were analyzed using ion chromatography, elemental carbon/organic carbon (EC/OC) analysis, and X-ray fluorescence (XRF) spectroscopy. Results showed that PM2.5 concentrations in urban areas were significantly higher than in suburban locations, with notably elevated levels at Changsha New Railway Station and Mapoling. Across different PM2.5 pollution levels, the eight sites exhibited pronounced spatial differences in concentration while sharing similar chemical compositions. Source apportionment identified secondary nitrate, vehicle emissions, and secondary sulfate as major contributors to PM2.5. The spatial distribution of these sources varied distinctly: secondary nitrate showed lower contributions in central areas but higher in western and southeastern regions; secondary sulfate was more prominent in the southeast, while vehicle emissions contributed more in the southeast and less in the west. Additionally, aerosol liquid water content promoted the secondary formation of nitrate and sulfate, exacerbating PM2.5 pollution. Secondary organic carbon was elevated in areas with high pedestrian density, suggesting enhanced secondary organic aerosol formation under intensive human activity. The study provides insights for targeted pollution control strategies in Changsha and similar cities.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025050801
Oil-contaminated water poses severe ecological and public health risks, yet conventional treatment technologies are hindered by complex processing and low selectivity. Metal-organic frameworks (MOFs) and their composites, with tunable pore structures, high surface areas, and controllable wettability, offer promising solutions. This review systematically classifies design strategies and synthesis methods for MOFs and MOF-based composites tailored for oil-water separation. We highlight recent advances, emphasizing structure–function relationships. Key performance metrics from representative studies include water contact angles up to 172.3°, separation efficiencies exceeding 99.9%, and adsorption capacities reaching 168 g·g⁻¹. Challenges such as scalability, stability, and fouling resistance are discussed, along with future directions for practical implementation.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042702
This study estimated initial volume mixing ratios of volatile organic compounds (VOCs) in Dalian from June 1 to August 31, 2024, using a photochemical age-based parameterization method, and performed source apportionment with positive matrix factorization (PMF). Observed average TVOCs concentration was 12.49×10⁻⁹, comprising alkanes (84.2%), alkenes (10.4%), and aromatics (5.4%). Corrected initial TVOCs was 14.93×10⁻⁹, indicating a loss rate of 16.4%. Loss rates were highest for alkenes (53.2%), followed by aromatics (23.3%) and alkanes (6.8%). Ozone formation potential (OFP) averaged 21.31×10⁻⁹ (observed) and 38.75×10⁻⁹ (initial), with an OFP loss rate of 45.0%, distributed as alkenes (56.4%), aromatics (32.7%), and alkanes (10.3%). During ozone pollution episodes, TVOCs chemical loss was 1.9 times that of non-pollution periods, with alkene loss reaching 61.6%; OFP loss was 1.2 times higher, with alkenes contributing 88.4% to TVOCs loss. Secondary organic aerosol (SOA) formation potential from 08:00–17:00 was 1.51×10⁻¹ μg·m⁻³, with 99.4% from aromatics and toluene contributing 68.3%. PMF identified five sources: motor vehicles (49.6%), oil and gas volatilization (20.7%), petrochemical enterprises (12.6%), industrial processes (11.2%), and solvent use (5.9%). OFP modeling indicated motor vehicles contributed most to ozone formation (41.1%), followed by petrochemical enterprises (35.8%). During ozone pollution, PMF based on initial concentrations showed petrochemical sources had the highest OFP contribution (42.5%), whereas observed concentrations indicated motor vehicles as the top contributor (42.5%). This discrepancy underscores the necessity of correcting for photochemical losses in source apportionment studies.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042703
This study investigated phosphorus (P) exchange at the sediment-water interface and its microbial driving mechanisms in aquaculture ponds of Chinese mitten crab (Eriocheir sinensis). Using diffusive gradients in thin films (DGT), labile P concentrations in the upper sediment were significantly higher than in overlying water from late July to mid-August and in October, indicating sediment acts as a P source during these periods. The duration of aquaculture was a key factor; P diffusion flux declined from late July to mid-August and further decreased by October. Analyses of labile Fe, P-Fe correlations, and bacterial community composition and function suggested that dissimilatory Fe(III) reduction mediated by Fe-reducing bacteria and chemical Fe(III) reduction driven by sulfate-reducing bacteria metabolites were important mechanisms for P release. Additionally, bacterial-driven organic P mineralization and inorganic P dissolution contributed. The results indicate a high risk of P release from sediment to overlying water from late July to mid-August, potentially significantly affecting water P concentrations. Therefore, controlling sediment P release during this period is crucial.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042504
This study investigated the effect of co-aging with common cations/anions and humic acid (HA) on the combined use of Vallisneria natans (VN) and lanthanum-modified bentonite (LMB) for controlling phosphorus (P) release from sediment. Results showed that co-aging significantly reduced the phosphate adsorption capacity of LMB, with the maximum unit adsorption capacity decreasing by 33.8% compared to the unaged material. Under the combined application of VN and unaged LMB, P in sediment could still be released into pore water via dissimilatory iron(III) reduction mediated by iron-reducing bacteria and chemical reduction of iron(III) induced by sulfate-reducing bacteria metabolites, subsequently migrating to overlying water. However, the combined treatment effectively inhibited P release, achieving an average reduction efficiency of 57.1% for dissolved reactive phosphorus (SRP) in overlying water and 74.0% for labile P in sediment (measured by DGT) at an LMB dosage of 89 g·m−2. Co-aging with common ions and HA diminished the P control efficiency of the combined treatment, primarily due to reduced phosphate adsorption capacity of LMB. Therefore, mitigating the negative effects of co-aging is crucial for enhancing the long-term P control performance of the VN-LMB combined technology.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608007
The Minjiang River Basin, subjected to combined pollution from domestic, agricultural, and industrial sources, has become a typical sensitive area for studying the environmental behavior of emerging contaminants such as antibiotics. This study conducted a cross-year comparative analysis of the composition and concentrations of antibiotics in water samples from nine sampling sites during the dry season in November 2022 and 2024. The findings revealed: 1) After the implementation of the "National Action Plan for Reducing Antimicrobial Use in Livestock", the detection concentrations of tetracycline antibiotics (TCs) decreased (e.g., doxycycline concentrations dropped from 7.75 ng/L to undetectable levels), and the mixed risk quotient (MRQ) across the entire basin transitioned from medium to low risk. However, lincomycin (up to 4.6 ng/L), clarithromycin (1.3 ng/L), and florfenicol (0.6 ng/L) have emerged, indicating an increasing hidden ecological risk from substitution. 2) High-concentration antibiotic zones transferred from urban residential areas in 2022 to intensive aquaculture zones and upstream reservoir areas in 2024. The reduction in dry-season water flow intensified pollutant accumulation, synergistically enhancing the effects of tidal drag. Additionally, the conversion of agricultural land to aquaculture ponds led to increased use of alternative drugs (e.g., sulfamethazine), while policy interventions mitigated the exacerbation of urban antibiotic pollution by construction land. This study elucidates the migration patterns of antibiotic pollution under the synergistic effects of policy regulation and natural processes, emphasizing the need to address hidden risks of substitute drugs and the driving role of land-use changes, providing scientific basis for watershed-scale risk assessment and precise management of emerging pollutants.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4034-3
The local concentration and configuration of active sites critically influence the selectivity of CO2 electroreduction, yet constructing well-defined structures to probe this relationship remains challenging. Here, we report a molten salt-assisted strategy to synthesize Ce-Ov-Cu cascade catalysts with tunable configurations and relative concentrations of Cu and Ce-Ov sites. Two distinct geometries were engineered: one with dense Cu sites surrounding Ce-Ov (Cu10CeOx) and another with isolated Cu centers encapsulated by Ce-Ov (CuCe10Ox). These configurations direct key intermediates (*CHO or *COH) toward either C-C coupling or deep hydrogenation, thereby switching product selectivity. CuCe10Ox achieves a CH4 Faradaic efficiency (FE) of 61.7% at -1.6 V vs. RHE, whereas Cu10CeOx favors C2 production with a maximum FE of 61.5% at -1.4 V vs. RHE. Mechanistic studies reveal that locally concentrated Cu sites exhibit strong *CO2 binding affinity, enhancing *CO surface coverage and facilitating *CO-*COH coupling. In contrast, Ce-Ov-rich regions with isolated copper centers supply abundant *H, promoting deep protonation of *CHO toward CH4. This work provides insights into catalyst design, demonstrating that manipulating structural chemistry can guide CO2RR toward targeted products.