SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4363-6
Aqueous zinc-ion batteries (AZIBs) offer a compelling combination of high safety, environmental compatibility, and abundant zinc resources, positioning them as viable candidates for grid-scale energy storage. Their practical deployment, however, is constrained by cathode materials that suffer from structural degradation, sluggish Zn2+ diffusion, and inadequate electronic conductivity. Ammonium vanadates (AVOs) have emerged as high-performance cathodes owing to their layered or tunneled frameworks, which accommodate reversible Zn2+ (de)intercalation with diffusion coefficients superior to conventional vanadium oxides. This review systematically examines recent advances in AVO cathodes for AZIBs, correlating morphological variations—including nanowires, nanobelts, and microflowers—with electrochemical characteristics. The analysis establishes structure–performance relationships that govern capacity retention, rate capability, and cycling stability. Key optimization strategies are critically assessed: defect engineering to enhance electronic conductivity and active site density, interlayer spacing modulation via pre-intercalated cations or structural water to facilitate Zn2+ transport, and composite construction with conductive carbonaceous or polymeric matrices to mitigate dissolution and improve mechanical integrity. Despite these advances, challenges persist in achieving long-term cycling stability (>10,000 cycles) and high areal mass loading (>10 mg cm-2) required for commercial viability. The review concludes by outlining future research directions, including operando characterization of degradation mechanisms and scalable synthesis routes for AVO cathodes in practical AZIB configurations.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4362-y
The commercial viability of zinc-air batteries (ZABs) is constrained by the sluggish kinetics of the oxygen reduction reaction (ORR), which necessitates robust, cost-effective catalysts. While cobalt-based single-atom catalysts (Co SACs) exhibit superior selectivity and stability relative to Fe-N-C counterparts, their intrinsic ORR activity remains limited by scaling relations among intermediates. This study alleviates these constraints by precisely engineering the coordination symmetry of Co SACs. Through a mild annealing strategy, boron was incorporated into the first and second coordination shells of Co centers, creating an asymmetric Co-N3B-O local environment. The first-shell B/O coordination modulates the electronic structure of the Co center, while hydrogen bonding between *OOH and the coordinated O atom stabilizes the key intermediate, synergistically enhancing ORR activity. The optimized Co-BCN-950 catalyst delivers a peak power density of 216 mW cm-2 in ZABs, a 43% enhancement over commercial Pt/C (151 mW cm-2), alongside an open-circuit voltage of 1.43 V and a specific capacity of 790 mAh g-1. These findings establish a paradigm for tailoring the local coordination of SACs, enabling next-generation high-stability energy storage systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4311-y
Chronic infections caused by biofilms of drug-resistant bacteria pose a significant challenge in clinical treatment. Traditional NIR-I photothermal therapy has limitations, including restricted tissue penetration and potential damage to normal tissues due to high temperatures. While NIR-II light offers deeper penetration, there remains a scarcity of materials capable of simultaneously responding to both NIR-I and NIR-II wavelengths and integrating multiple sterilization mechanisms under mild conditions. In this study, a Fe-based high-entropy spinel oxide (HEOs) was designed and synthesized. Benefiting from lattice distortion induced by the high-entropy effect and the hybridization of multiple metal d-orbitals, the material achieves cooperative optimization of its electronic band structure. Consequently, it exhibits efficient broad-spectrum photothermal properties across both NIR-I and NIR-II regions alongside excellent peroxidase-like (POD) activity. Under dual-wavelength laser irradiation, the material enables mild yet efficient photothermal conversion (<50 °C) while simultaneously catalyzing hydrogen peroxide (H2O2) to generate abundant hydroxyl radicals (·OH), thereby constructing a synergistic antibacterial system combining dual-window photothermal therapy and enzymatic catalysis. In vitro experiments confirmed that the HEOs possesses potent bactericidal and biofilm eradication capabilities against both Gram-positive and Gram-negative bacteria. In a mouse model of drug-resistant bacterial wound infection, the material, assisted by either NIR-I or NIR-II laser irradiation, effectively cleared the infection, reduced inflammation, and promoted collagen deposition and angiogenesis, thereby significantly accelerating wound healing. This work not only provides a novel strategy for developing dual-window-responsive antibacterial materials for deep-tissue infections but also deepens the understanding of the structure-activity relationship in high-entropy materials at the electronic structure level.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4288-1
The high-temperature oxidation resistance of Cr2AlC MAX phase ceramics is severely compromised by rapid Al depletion and the formation of a brittle sub-surface Cr7C3 layer. This study elucidates how trace Y2O3 doping (0.25 and 0.5 wt.%) modulates the oxidation behavior of Cr2AlC at 1100 °C. The incorporation of 0.5 wt.% Y2O3 significantly suppresses the parabolic rate constant compared to undoped counterparts. This kinetic suppression is attributed to the Reactive Element Effect (REE), where Y3+ segregation at α-Al2O3 grain boundaries inhibits outward Al3+ diffusion, shifting the scale growth mechanism to inward oxygen diffusion control. Consequently, this retarded Al consumption prevents the decomposition of the Cr2AlC substrate into Cr7C3. While undoped specimens fail due to volume contraction and Kirkendall voiding associated with the Cr7C3 interlayer, specimens with the most effective doping content within the investigated range maintain a stable, atomically sharp α-Al2O3/Cr2AlC interface devoid of voids and decomposition products. The superior adhesion of this interface is attributed to three synergistic factors: the elimination of volumetric mismatch induced by phase transformation, the mechanical interlocking provided by Y-rich oxide pegs, and the intrinsically higher interfacial bonding strength of the α-Al2O3/Cr2AlC system as confirmed by DFT calculations. These findings provide a mechanistic framework for designing oxidation-resistant MAX phase ceramics via reactive element doping.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4138-5
Electrocoagulation (EC) has emerged as a promising electrochemical technology for wastewater treatment, offering distinct advantages over conventional chemical coagulation and membrane processes. This review systematically summarizes recent advancements in EC, focusing on the underlying mechanisms, key operating parameters, and diverse technical applications. The EC process involves three stages: electrolytic oxidation and in-situ coagulant formation, destabilization of contaminants, and floc formation. Unlike chemical coagulation, EC requires no external chemical additives, and process control is achieved by adjusting current density, voltage, or electrode materials, enabling adaptation to varying wastewater qualities. The review highlights the influence of dissolved organic matter (DOM) on EC efficiency, as clarified by Luo et al. (Water Research, 2025). Furthermore, it discusses reactor design innovations, including continuous-flow and cascade-type configurations, and the role of current waveforms in mitigating electrode passivation. The integration of EC with membrane bioreactors and forward osmosis is also examined, demonstrating enhanced treatment performance and fouling mitigation. Key challenges, such as energy consumption and electrode scaling, are addressed, along with future research directions. This comprehensive analysis provides a critical framework for optimizing EC systems and scaling them for industrial wastewater treatment, emphasizing the need for holistic reactor design and process integration to achieve sustainable water reuse.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4339-7
Neuromorphic computing demands energy-efficient synaptic devices that emulate biological plasticity. Optoelectronic memristors based on colloidal quantum dots (QDs) offer tunable bandgaps and solution processability, yet suffer from defect-mediated nonradiative recombination and instability. Here, we report ZnS-passivated CdZnSe core/shell QDs as the active layer in memristive devices, achieving enhanced synaptic emulation and information encryption. Time-resolved photoluminescence (TRPL) decay curves were fitted with a tri-exponential function, revealing that ZnS passivation suppresses defect-related trap states, prolonging the average carrier lifetime from 12.3 ns (CdZnSe) to 28.7 ns (CdZnSe/ZnS). The intensity proportion of the fast decay component (τ1 ≈ 1.2 ns) decreased from 45% to 18%, indicating reduced surface trapping. Devices incorporating CdZnSe/ZnS QDs exhibit stable bipolar resistive switching with an ON/OFF ratio exceeding 10^3, endurance of >10^3 cycles, and retention of >10^4 s. Under 365 nm UV illumination, the devices show light-tunable synaptic plasticity, including paired-pulse facilitation (PPF) with a facilitation index of 180% at a 50 ms interval, and transition from short-term to long-term memory. The memristors successfully emulate essential synaptic functions and are employed in a simple encryption scheme, demonstrating the potential of defect-passivated QDs for secure neuromorphic hardware.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4359-0
Organic solar cells (OSCs) require cathode interlayers (CILs) that combine high charge transport, defect passivation, and thickness insensitivity for scalable manufacturing. Here, we report the synthesis of a novel A-D-A-A'-type polymer, PDPP2F-NDI-N, via the green and efficient direct arylation polymerization (DArP) method. The multiple electron-deficient units in the backbone confer strong electron-withdrawing character, effective work function modulation, enhanced built-in potential, high crystallinity, and ordered molecular packing. PDPP2F-NDI-N exhibits a high electron mobility of 1.01 × 10⁻³ cm² V⁻¹ s⁻¹ and electrical conductivity of 3.13 × 10⁻³ S m⁻¹, facilitating efficient charge extraction and transport. Its interfacial modification capability suppresses interfacial defects and reduces non-radiative recombination losses. In ternary OSCs, PDPP2F-NDI-N achieves a high power conversion efficiency (PCE) of 20.44%, with outstanding thickness insensitivity retaining 92.8% of peak PCE at a 30 nm CIL thickness, and a T80 lifetime exceeding 1700 hours under photo-thermal aging. This work demonstrates that poly(A-D-A-alt-A') backbone design combined with DArP synthesis provides an effective strategy for developing high-performance, thickness-insensitive, and stable polymeric CILs, advancing efficient, stable, and scalable OSC applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4317-4
This correction addresses an image assembly error identified in Fig. 7a of the original article published in Science China Materials, volume 66, issue 6, 2023, pages 2513–2522. The error was confined to the assembly of images in Fig. 7a, which presents H&E staining analysis of major organs from a toxicity study. The corrected version of Fig. 7 is provided in this corrigendum. The original study evaluated the toxicity of lyophilized cabazitaxel (CTX) and Tween 80-based CTX formulations in CD-1 mice following a single intravenous administration of 30 mg kg−1 CTX via the tail vein on day 0, with sacrifice on day 14 for analysis (n=5). The figure includes H&E staining of major organs, complete blood count (CBC) analysis with statistical significance indicated by *p < 0.05, and mouse weight measurements. The correction does not affect the overall results, data interpretation, or scientific conclusions of the original article. All authors have reviewed and approved the content of this corrigendum. The authors sincerely apologize for any inconvenience caused to the editorial office, reviewers, and readers. The article was received on 6 May 2026, accepted on 4 June 2026, and published online on 31 July 2026.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4207-0
Self-assembled monolayers (SAMs) are critical for optimizing electrode interfaces in organic solar cells (OSCs), as their molecular conformation and ordering govern interfacial quality. Conventional carbazole-based SAMs (e.g., 2PACz) rely on flexible alkyl linkers whose conformational freedom often results in disordered packing, incomplete coverage, and limited environmental robustness, especially under air processing. Here, we design and systematically study a series of well-defined carbazole SAM homologues (Cz-PPA, Cz-HPA, PCz-HPA, and PCz-PPA) to elucidate the role of synergistic conformational locking achieved through linker rigidification and terminal conjugation extension. PCz-HPA, which integrates a rigid cyclohexane linker with a strongly conjugated 3,6-diphenylcarbazole end group, enables effective conformational locking. It forms a highly ordered, densely packed monolayer on ITO, delivering high surface coverage, a strengthened interfacial dipole, and improved energy-level alignment. The rigid framework and ordered interface enhance air-process stability and interfacial contact, thereby suppressing recombination and facilitating exciton dissociation and charge collection. Using PCz-HPA as SAM for the devices based on PM6:L8-BO reaches 19.75% efficiency and it demonstrates consistent gains across multiple systems. These results identify conformational locking via linker rigidification as a general design rule for durable, high-performance SAM interlayers in organic optoelectronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3831-0
Ammonia decomposition is a key process for generating COx-free hydrogen, yet conventional cobalt catalysts require high temperatures (>550 °C) to overcome the strong Co–N binding that limits N2 desorption. Here we report a novel Co catalyst supported on a Ce and N co-modified perovskite (Co@La_xCe_{1-x}AlO_{3-y}N_z) that achieves 92.6% ammonia conversion with a hydrogen production rate of 9.7 mmol g−1 min−1 at 425 °C and GHSV = 9000 mL h−1 g_cat−1, representing a 125 °C reduction in operating temperature relative to conventional Co-based catalysts. Mechanistic studies using isotopic labeling and in-situ DRIFTS reveal that synergistic Ce and N modification creates a unique LA-L(A+B)-LB active site configuration, which lowers the Schottky barrier at the metal-support interface and promotes facile hydrogen spillover. The reaction proceeds via an interfacial Mars-van Krevelen mechanism, contrasting with the traditional Langmuir-Hinshelwood pathway on conventional Co catalysts. This work provides new insights for designing low-temperature Co-based ammonia decomposition catalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3848-7
Conventional heterogeneous photocatalysts often suffer from insufficient light absorption, rapid charge recombination, and a lack of specific reactive sites for efficient photocatalytic oxidation. To overcome these limitations, we propose a molecular polarization engineering approach utilizing structurally well-defined donor (D)-acceptor (A) covalent triazine frameworks (CTFs). The construction of dipole-induced built-in electric fields within the D-A-structured CTFs enables enhanced exciton dissociation and facilitates directional charge transfer. Specifically, the asymmetric A1-D-A2 moiety enhances molecular polarization in the dual-acceptor system CTF-TBT (A1-D-A2), enabling efficient charge separation through multiple electron-withdrawing units. This structural design promotes directional electron transfer toward the secondary acceptor (benzothiazole, A2), while simultaneously concentrating holes on the donor unit. Consequently, the A2 moiety acts as a site for efficient O2 activation via electron accumulation, whereas the highly oxidized donor unit provides strongly positive holes (h+) that facilitate substrate oxidation. Experimental and DFT calculation results confirm that CTF-TBT demonstrates highly enhanced photocatalytic oxidation performance, which can be attributed to its multi-channel charge separation mechanism and spatially separated redox-active sites. This study highlights the effectiveness of molecular dipole engineering in designing heterogeneous photocatalysts with controlled charge transfer pathways and improved redox capabilities. The proposed design principles provide a universal approach for promoting solar-driven chemical synthesis applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3642-4
High-density glass scintillators are promising alternatives to crystals for next-generation radiation detection due to their low cost, excellent physical and chemical stability, and processability. In this study, a series of Ce3+-activated gadolinium gallium borosilicate (GGBS x) glasses were synthesized via vacuum melt-quenching. With increasing Gd2O3 content, glass density increased from 5.86 to 6.05 g/cm3, and molar volume from 36.43 to 39.79 cm3/mol. Extended X-ray absorption fine structure (EXAFS) analysis revealed that in GGBS 1 glass, Ce3+ exclusively adopts a hexahedral [CeO6] configuration, while Gd3+ exhibits both hexahedral and octahedral coordination with a bond length of 2.35±0.1 Å and Debye-Waller factor σ2 of 0.0122±0.0015 Å2. As Gd2O3 content increased, shallow trap depth rose from 0.804 to 0.858 eV, while deep trap depth first increased from 0.948 to 1.434 eV then decreased to 1.010 eV. GGBS 1 glass exhibited high transmittance (~80%) in the visible range and a photoluminescence quantum yield of 78.4%. Under X-ray irradiation, its X-ray excited luminescence intensity reached 128.5% of that of Bi4Ge3O12 (BGO) crystal, with a spatial resolution of 29.1 lp/mm, approaching the highest reported for glass scintillators. Under γ-ray excitation, it achieved a light yield of 1058 photons/MeV and an energy resolution of 23.7% at 662 keV. These results indicate that GGBS 1 glass scintillator warrants further development for applications in X-ray imaging and γ-ray spectroscopy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3630-2
This study demonstrates a dual-interface engineering approach for performance enhancement in perovskite-silicon tandem solar cells. By applying ethylenediamine dihydroiodide (EDAI2) to simultaneously modify both top and bottom interfaces of wide-bandgap perovskite layers, we achieve synergistic defect suppression and charge transport optimization. Time-resolved photoluminescence characterization reveals extended carrier lifetimes and improved spatial homogeneity in dual-modified perovskite films. The optimized single-junction wide-bandgap (>1.66 eV) perovskite solar cells attain a champion efficiency of 22.75% with enhanced operational stability. Implemented in perovskite-silicon tandem configuration, the devices achieve over 31% power conversion efficiency, validating the effectiveness of organic ligand-mediated dual-interface engineering in regulating carrier dynamics and advancing perovskite-based tandem photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3710-y
Layered transition metal oxide cathodes for sodium-ion batteries (SIBs) suffer from Jahn–Teller distortion of MnO6, Na+/vacancy ordering, and irreversible lattice oxygen loss, causing capacity fading and voltage decay. Here, we report a P2-type material, Na0.67Ni0.3Mn0.6Li0.09Sn0.01O2 (NNMO-Li0.09Sn0.01), co-doped with closed-shell Li+ and Sn4+ ions. Li+ increases the Mn4+/Mn3+ ratio, mitigating Jahn–Teller distortion, and disrupts Ni/Mn ordering, suppressing Na+/vacancy ordering. Sn4+ forms stronger Sn–O bonds (548 kJ mol−1), enhancing bonding between transition metal ions and oxygen, reducing oxygen loss. NNMO-Li0.09Sn0.01 delivers a specific capacity of 90.3 mAh g−1 with 62.9% capacity retention after 50 cycles at 0.1 C (1 C = 200 mA g−1), and 90.3% voltage retention. This closed-shell substitution strategy offers a viable approach for enhancing structural stability of wide-voltage layered oxide cathodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3581-2
Radiotherapy (RT) is a standard cancer treatment that directly kills tumor cells and promotes systemic immune responses. However, RT can exacerbate tumor hypoxia, which suppresses dendritic cell (DC) antigen presentation and weakens systemic anti-tumor immunity. Here, we report oxygen-loaded in situ gels carrying bacterial outer membrane (MOGel) that slowly degrade to release oxygen and bacterial outer membrane (OM). Oxygen release alleviates tumor hypoxia, while OM continuously activates DCs, enhancing their antigen-presenting capability. In vitro, MOGel combined with RT induced the strongest tumor cell apoptosis. In an orthotopic colon cancer model, MOGel+RT achieved an 80% tumor suppression rate. Notably, MOGel+RT elicited an enhanced abscopal effect, with hypoxia relief and enhanced DC activation contributing to systemic immune responses. These findings suggest that OM-based oxygen gels offer a novel strategy to enhance systemic immune responses to RT.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507085
This study investigates the spatiotemporal differentiation of suspended particulate matter (SPM) characteristics, sources, and their impacts on water quality between the Middle Route (closed artificial channel) and East Route (open natural water system) of the South-to-North Water Diversion Project. Thirty sampling sites (13 on the Middle Route, 17 on the East Route) were established, and samples were collected during dry and wet seasons. Water quality parameters and SPM characteristics were analyzed, including particle size distribution, total suspended solids (TSS), chlorophyll a, and stable carbon and nitrogen isotopes. Results show that the Middle Route maintains good and stable water quality, with SPM dominated by coarse particles (>63 μm, 61.43%–94.68%), total phosphorus (TP) <0.01 mg·L−1, and a significant positive correlation between chlorophyll a and coarse particles (r=0.60), indicating algal aggregation dominates particle formation. In contrast, the East Route exhibits high and fluctuating nitrogen and phosphorus concentrations, with SPM dominated by fine particles (<20 μm, 51.26%–88.61%), TP ranging from 0.03 to 1.11 mg·L−1, and a positive correlation with fine particles, suggesting significant external inputs. Carbon and nitrogen isotope analysis reveals that Middle Route SPM primarily originates from autochthonous algae (contribution >46.75%), while East Route SPM is influenced by both terrestrial C3 plants and algae. The distinct engineering and management approaches of the two routes lead to significant differences in SPM characteristics and sources, thereby affecting water quality dynamics. The Middle Route requires an 'algal reduction and hydrodynamic optimization' strategy to control algal-derived coarse particle deposition, whereas the East Route benefits from 'retention-sedimentation and wetland purification' to reduce external fine particles and pollutant inputs. This research provides theoretical support and practical guidance for differentiated SPM management in long-distance water diversion systems.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507055
The increasing complexity of pollutant sources in municipal wastewater networks, driven by unauthorized industrial discharges, poses significant risks to the stable operation of wastewater treatment plants. This study, conducted in an industrial park in Ningbo, Zhejiang Province, developed a source apportionment method using excitation-emission matrix (EEM) fluorescence spectroscopy combined with spectral angle mapping (SAM). A pollution fingerprint database was constructed from wastewater samples of six representative enterprises (A–F) and municipal sewer samples. The SAM algorithm demonstrated high sensitivity and stability in detecting changes in water composition, with spectral angle values showing a strong linear correlation (R² > 0.88) with the volume ratio of enterprise wastewater in mixed samples. This enabled both qualitative identification and quantitative estimation of pollution sources. Field application over a 12-hour monitoring period identified two enterprises as major contributors to organic matter and nitrogen during critical pollution episodes, consistent with trends in DOC, TN, and UV254. The proposed EEM+SAM approach offers a non-invasive, high-throughput method for real-time monitoring and source tracing of multi-source pollution in complex sewer systems, providing a scientific basis for pollution accountability and precise enforcement.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60581-0
Lignin-derived oxygenated aromatics, particularly phenols and aromatic ethers, are promising feedstocks for synthesizing high-density, high-heat-sink aviation fuels via alkylation-hydrogenation processes. This study systematically evaluates the catalytic performance of various zeolites (Hβ, HZSM-5, MCM-41, and HUSY) in the alkylation of phenol with cyclohexanol. Characterization demonstrates that HUSY zeolite exhibits superior catalytic activity due to its favorable pore architecture and well-balanced acid site distribution, which synergistically facilitate molecular diffusion and catalytic transformations. To further enhance catalytic properties, HUSY was modified with citric acid at various concentrations and compared with NaOH and oxalic acid treatments. Results reveal that citric acid treatment preserves crystallinity while modulating acidity and pore structure. All modified zeolites enhance phenol alkylation activity. Notably, HUSY-0.5M, exhibiting the highest medium-strong acid to total acid ratio, achieves superior performance: 80.4% phenol conversion and 99.6% selectivity for alkylation products. The catalyst also shows high activity for various lignin-derived compounds (p-cresol, anisole, guaiacol), demonstrating broad applicability. This work provides a new strategy for valorizing lignin-derived phenols into high-value fuel precursors through alkylation.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512072
Drainage pipeline defect detection predominantly relies on closed-circuit television (CCTV) inspection, which is labor-intensive, inefficient, and prone to missed detections. Although deep learning-based object detection has been applied, it suffers from low precision, recall, and speed in practical scenarios. This study proposes an engineering-oriented detection scheme achieving high recall and low miss rates. The annotation phase employs a cross-frame strategy combining manual labeling of first and last frames with interpolation and tracking-based refinement. Data preprocessing introduces perceptual hashing to identify similar images, enhancing training efficiency. For detection, a Faster R-CNN model is enhanced with Focal Loss to focus on hard examples, defect classification and grading, and a dynamic threshold strategy to improve recall. Validated on 5,068.72 m of real pipeline data, the method achieves a recall rate exceeding 98% across 16 defect categories, a miss rate of only 2% for grade 4 defects, and a 425% improvement in per-segment detection efficiency compared to manual screening. These results demonstrate the method's effectiveness in balancing recall, miss rate, and speed for engineering deployment.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0027
Electrocatalytic CO2 reduction reaction (CO2RR) offers a promising route to mitigate CO2 emissions while producing valuable chemicals. This study reports a Cu-Sn alloy catalyst with a wheat-ear-like dendritic structure, fabricated via a one-step electrodeposition method, for selective CO2 electroreduction to formate. Compared to pure Cu and Sn electrodes, the Cu-Sn alloy exhibits superior catalytic activity and selectivity toward formate, achieving a maximum Faradaic efficiency (FE) of 80% and maintaining above 70% FE over a potential window from -1.7 V to -2.0 V (vs. Ag/AgCl). The enhanced performance is attributed to the unique dendritic morphology that provides abundant active sites and the synergistic alloying effect that modulates the adsorption of the CO2*- intermediate, as corroborated by electrochemical measurements and X-ray photoelectron spectroscopy (XPS). This work presents a facile strategy for designing bimetallic catalysts for efficient CO2RR to formate.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112101
The biological reduction of Cr(VI) to less hazardous Cr(III) is a promising strategy for remediating Cr(VI)-contaminated sites. Both biochar and riboflavin can act as electron shuttles to accelerate this bioreduction process, yet their combined effects remain poorly understood. Using Shewanella oneidensis MR-1 as a model reducing bacterium, we investigated the joint influence of biochar (average particle size 28.85 μm) and riboflavin at high (1 mmol·L−1) and low concentrations on Cr(VI) bioreduction. Individually, biochar and high-concentration riboflavin enhanced indirect electron transfer, accelerating Cr(VI) removal. However, when combined, the fast-phase reaction rate (rf0) did not significantly improve compared to single amendments. The combined action factor revealed an antagonistic inhibition between biochar and riboflavin. Mechanistically, high-concentration riboflavin saturated biochar's adsorption sites (equilibrium concentration 0.96±0.04 mmol·L−1), hindering biochar's role as an electron conduit. With a bacterial density of 3.4×10^7 cells·mL−1, the inter-bacterial distance (30.87 μm) exceeded biochar's particle size, and the per-cell riboflavin concentration (2.9×10−2 pmol·cell−1) was sufficient for riboflavin to dominate as the primary electron shuttle, while biochar's surface became coated, reducing its efficacy. These findings reveal the complex interplay between biochar and soluble organic matter in Cr(VI) bioreduction, underscoring the need to consider such antagonistic effects when designing bioremediation strategies for multi-component contaminated environments.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604025
To meet the minute-level early-warning requirements for odor and multi-pollutant emissions at waste treatment facilities, this study proposed a multivariate short-term time-series prediction framework applicable to multi-tier scenarios covering source and boundary points (i.e., workshops and plant boundaries). Based on continuous online monitoring data with a 5-second resolution, a long short-term memory (LSTM) model using a sliding-window and recursive multi-step prediction strategy was constructed to jointly model odor concentration (OU) and pollutants including VOCs, NH3, H2S, and CH3SH (mg/m³). An evaluation protocol aligned with environmental supervision practice was established, incorporating mean absolute error (MAE), root mean square error (RMSE), goodness-of-fit (R²), skill scores (SS) relative to a persistence baseline, and threshold-based error stratification to characterize uncertainty during peak emission periods. The results showed that at workshop monitoring sites with relatively stable operating conditions, VOCs, NH3, H2S, and CH3SH exhibited a high goodness of fit and low prediction errors. In contrast, at boundary sites affected by plume arrival delays and diffusion-dilution non-stationarity, OU and VOCs displayed significantly amplified errors during peak episodes, and the skill score advantage over the baseline became unstable at certain sites. Stratified analysis consistently revealed that non-peak periods outperformed peak periods, indicating that event-driven fluctuations were the main sources of error. Accordingly, this study suggested incorporating exogenous variables such as wind speed and direction, ventilation and gate access control, and operational rhythms, along with peak-sensitive loss functions, into the model to enhance its capacity to characterize and provide early warnings for transient emission pulses. Overall, this study established a reusable methodological baseline and evaluation paradigm for minute-scale multi-pollutant prediction, providing quantitative support for the operational management and source-to-boundary coordinated control of waste treatment facilities.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3778-8
The global surge in polyvinyl chloride (PVC) waste demands urgent technological solutions that address both environmental persistence and resource recovery. Here, we present a triple-functionalization strategy that converts chlorinated plastic waste into high-performance sodium-ion battery anodes through molecular-level control of carbon architectures. Sequential dichlorination, sulfonation, and N-doping collaboratively reconfigure precursor reactivity, steering pyrolysis toward hierarchically porous hard carbon with tailored defect chemistry. Sulfonic groups stabilize 3D carbon skeletons during carbonization, enabling closed-pore formation with an average diameter of ~2.55 nm while N-doping expands interlayer spacing (0.382 nm) and creates adsorption-active pyrrolic-N sites. This defect-engineered synergy delivers unprecedented sodium storage metrics: 355 mAh g−1 reversible capacity at 0.1 A g−1 (95.4% of graphite’s Li-ion capacity), a capacity retention of 216 mAh g−1 after 1000 cycles at 1.0 A g−1 (70.1% capacity retention), and 188 mAh g−1 even at a high current density of 5.0 A g−1. Operando analyses reveal a potential-dependent storage hierarchy: surface-dominated adsorption transitions to intercalation/filling-dominated behavior with defect-buffered structural integrity. The process simultaneously achieves 25% carbon yield from PVC and avoids toxic dioxin emissions, establishing a scalable prototype for sustainable energy storage systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4028-5
The escalating thermal management demands of modern electronics necessitate materials with superior thermal conductivity and matched thermal expansion. Cu/Diamond composites are promising, yet their fabrication typically requires extreme conditions (high temperature/pressure) or complex coating processes. This work introduces a one-step, heat-source-free cold manufacturing method using ultrasonic vibration to consolidate Cu/Diamond composites at room temperature and a low pressure of ~16 MPa within seconds. The applied pressure is reduced by 200–500 times, and the required temperature is only 20% of that used in conventional high-temperature high-pressure sintering. Direct metallurgical bonding at Cu-Cu interfaces and solid embedding of diamond particles in the Cu matrix are achieved, yielding a composite with a high yield strength of 150 MPa. The method enables a maximum diamond proportion of ~60%, resulting in a thermal conductivity exceeding 1043 W/(m·K) and a coefficient of thermal expansion below 10×10⁻⁶ K⁻¹. Complex shapes are readily fabricated, and heat dissipation tests demonstrate superior performance compared to commercial Al₂O₃ and AlN substrates. The loose preparation conditions and rapid processing confer significant industrial production potential.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4043-3
In-plane InAs nanowires and nanowire networks are promising platforms for electronics, optoelectronics, and topological quantum computing due to their small electron effective mass, narrow bandgap, high electron mobility, strong spin-orbit coupling, and large Landé g factor. However, their selective area growth on CMOS-compatible group-IV substrates remains challenging. Here, we report the selective area growth of high-quality in-plane InAs nanowires and nanowire networks on Ge(111) substrates by molecular-beam epitaxy. Conventional selective-area epitaxy fails to simultaneously achieve good selectivity and continuity. To overcome this, we developed a metal-sown, single-indium-source two-step growth method, which attains both selectivity and continuity but yields nanowires with rough surfaces and lengths below 10 μm. We then introduced an upgraded metal-sown, dual-indium-source two-step growth method, successfully fabricating in-plane InAs nanowires and nanowire networks with smooth surface morphology and lengths exceeding 60 μm. By optimizing the As beam equivalent pressure, overgrowth at network junctions is effectively suppressed, resulting in uniform nanowire networks. High-resolution transmission electron microscopy and Raman spectroscopy confirm the high-quality single-crystalline nature and pure zinc-blende structure of the nanowires and networks. This work establishes a foundation for fabricating high-quality in-plane InAs/superconductor hybrid nanowires and nanowire networks on Ge substrates.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3856-0
Replacing the kinetically sluggish oxygen evolution reaction (OER) with biomass oxidation at photoanodes offers a cost-effective and energy-efficient route for simultaneous hydrogen production and value-added chemical synthesis in a photoelectrochemical (PEC) cell. Here, titanium-doped hematite nanorods (Hem) decorated with CoNi bimetallic zeolitic imidazolate frameworks (ZIF) were prepared via room-temperature deposition and employed as photoanodes for 5-hydroxymethylfurfural (HMF) oxidation. Using 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO) as a redox mediator in alkaline electrolyte, the CoNi-ZIF/Hem photoanode achieved a photocurrent density of 1.09 mA cm−2 at a low bias of 1.1 V vs. reversible hydrogen electrode (RHE). Experimental results and theoretical calculations reveal that CoNi-ZIF accelerates charge transfer and separation, and enhances TEMPO adsorption on the surface, benefiting PEC TEMPO-mediated HMF oxidation to 2,5-furandicarboxylic acid (FDCA). In a flow-cell reactor under 1 sun illumination, the photoanode achieved ~99% HMF conversion and ~98% FDCA yield within 2 hours. The photoanode also exhibited excellent performance for TEMPO-mediated oxidation of various aldehyde-containing biomass-derived compounds. This work demonstrates a rational design of hematite-based photoanodes for efficient biomass valorization coupled with hydrogen production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3800-7
Two-dimensional van der Waals (vdW) crystals, stacked via atomically thin layers, exhibit rich functionalities and tunable stacking orders. Their mechanical behaviors are crucial for flexible and miniature electronics. While some vdW crystals show superior plasticity, the mechanical properties of SnS2 bulk crystals remain largely unexplored. Here, we synthesize high-quality SnS2 crystals via the Bridgman method and comprehensively investigate their mechanical properties. SnS2 bulk crystals exhibit remarkable plasticity and softness: bending and compression strains exceed 20% and 45%, respectively, without fracture, while tensile fracture strains reach up to ~12% (range 9%–16%). Scanning/transmission electron microscopy reveals multiple deformation units, including layer segments, interlayer/cross-layer slip, twisting, and twinning-like structures. These units provide multiple pathways to release strain energy, promoting plasticity. Alongside weak interlayer vdW interactions, relatively ionic and weak intralayer Sn–S bonds contribute to the softness. This work fills the knowledge gap on SnS2 mechanical properties, advancing its processing and application in diverse electronic devices. Further studies may focus on balancing plasticity and strength by tuning microstructure to activate but confine deformation units.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61093-1
Advanced catalyst structures with good active site accessibility and strong metal-support interactions are crucial for oxygen reduction reaction (ORR) catalysis. A hierarchically porous Pt catalyst supported on honeycomb-like nitrogen-doped carbon (Pt/HNC-400, where 400 denotes the optimal dosage (mg) of the sacrificial SiO2 hard template used during synthesis) was fabricated by combining template-assisted pyrolysis and alcohol reduction. The fabrication involves the template-assisted pyrolysis of ZIF-67 (which provides the N-dopant through its 2-methylimidazole ligand) followed by HF etching to completely remove the SiO2, yielding a 3D interconnected porous carbon support. Compared to a commercial Pt/C, it had an exceptional ORR performance with a half-wave potential of 0.901 V (41 mV higher), a mass activity at 0.9 V that was 15.3 times higher, and significantly improved durability (a half-wave potential decay of 25 mV vs. 80 mV after 10,000 accelerated durability tests (ADTs)). Mechanistic investigations showed that this superior performance is due to the combined effects of the 3D porous structure, ultrafine Pt nanoparticles with strong metal-support interactions, and in-situ formed Co-Nx moieties from the pyrolysis of precursor ZIF-67. After 10,000 ADTs it was shown to have excellent structural integrity, retaining 87.4% of its initial electrochemically active surface area (102.7 m2 g−1). This study may assist the development of new high-performance ORR catalysts.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508050
This study investigated the spatial distribution and ecological risk of heavy metals (As, Cd, Cr, Cu, Ni, Pb, Zn) in soil beneath an informal waste dump in a pastoral area of Baingoin County, Nagqu City, Tibet, a high-altitude cold region with frequent freeze-thaw cycles. A total of 55 soil samples were collected from surface (0 cm), middle (10-30 cm), and deep (50 cm) layers. Single-factor index (Pi), geo-accumulation index (Igeo), Nemerow index (PN), and risk assessment code (RAC) were employed to evaluate contamination levels and potential ecological risks, while Kriging interpolation was used to map spatial distribution. Results showed that average concentrations of all seven heavy metals exceeded local background values. Horizontally, high-concentration zones were mainly located at five points within the dump. Vertically, Cd, Cu, Pb, and Zn were significantly enriched in the surface layer, whereas Ni exhibited higher concentrations in deeper layers, indicating downward migration driven by freeze-thaw processes. All evaluation methods identified Cd as the primary pollutant. Speciation analysis revealed that heavy metals were predominantly in the residual fraction, with Ni having the highest weak-acid-extractable fraction (5.55%), indicating strong mobility and potential biological toxicity. This study fills a gap in systematic research on informal waste dumps in high-altitude ecologically fragile areas and provides a case reference for environmental management and remediation of such sites in cold regions.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60640-8
Ethylene (C2H4) in vehicle exhaust is a highly reactive volatile organic compound (VOC) whose photo-oxidation with NOx contributes to the formation of O3 and secondary organic aerosols (SOA), a key precursor of PM2.5. This study designs a novel MgO-supported Ag-Cu bimetallic catalyst and investigates its performance using density functional theory (DFT). The effects of Ag and Cu loading on geometric structure, stability, and reactant adsorption are analyzed, and the catalytic oxidation pathways of C2H4 over AgCu-MgO are elucidated. Results indicate that loading Ag significantly enhances C2H4 adsorption, with a maximum adsorption energy of -1.46 eV, while O2 adsorption remains weak (-0.45 eV). Cu-MgO shows moderate C2H4 adsorption (-0.87 eV at bridge site) but higher O2 adsorption (-0.76 eV). Among 17 AgCu-MgO dual-atom catalyst (DAC) configurations, those with Ag and Cu co-adsorbed at Mg sites are thermodynamically more stable (binding energies below -10 eV). Configurations with Ag and Cu in close proximity enhance co-adsorption of C2H4 and O2. C2H4 oxidation preferentially proceeds via C=C bond cleavage to form *CH3 and CO2. For three representative configurations (1, 3, 6), free energy barriers for rate-limiting steps in the *HCO and CH2O pathway are consistently higher than those for *CH3 and CO2 pathway. Configuration 6 exhibits the lowest energy barrier (0.32 eV) for its rate-limiting step, indicating the highest catalytic performance. This study provides atomic-scale insights for rational design of efficient catalysts targeting olefinic pollutants in automotive emissions.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025110501
Ultrashort-chain perfluoroalkyl substances (PFAS) exhibit high hydrophilicity, mobility, and root concentration factors, facilitating their transport and accumulation in soil-crop systems and posing phytotoxicity risks. Post-drought rehydration (PDR) is a critical water management strategy to mitigate drought effects in paddy fields. This study investigated the regulation and mechanisms of PDR on ultrashort-chain PFAS transport in paddy soils through sterilized and non-sterilized experiments, employing three-dimensional fluorescence spectroscopy, Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, X-ray fluorescence spectroscopy, and amplicon sequencing. Results showed that PDR increased the bioavailable fraction of ultrashort-chain PFAS in soil solution while delaying their release into overlying water. Sterilization experiments confirmed that PDR-induced compensatory migration was primarily driven by microbial activity. Geochemical analyses revealed that PDR reduced hydrophilic functional groups (e.g., hydroxyl) on soil particle surfaces and increased cation bridging sites. Microbiological sequencing indicated that PDR activated secondary metabolic pathways, enhancing microbial extracellular polymeric substances (EPS) production, which provided binding sites for ultrashort-chain PFAS. Consequently, EPS competed with soil particles for cation bridging, altering PFAS interfacial partitioning and increasing bioavailable and cation-complexed fractions in soil solution, thereby exacerbating rhizosphere exposure risk to rice. This study elucidates the coupled geochemical and microbiological mechanisms governing ultrashort-chain PFAS mobility under PDR, informing risk assessment and management in paddy agroecosystems.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012101
Continuous monitoring of 114 volatile organic compounds (VOCs) was conducted in the urban atmosphere of Haigang District, Qinhuangdao City, from September 2022 to February 2023. The volume concentrations of total VOCs were 42.72×10⁻⁹ in autumn and 25.15×10⁻⁹ in winter. The predominant species were isopentane, ethane, and ethylene. Ozone formation potential (OFP) analysis indicated that alkanes and alkenes dominated the atmospheric pollution during autumn and winter, with isopentane and ethylene being the largest contributors. Aromatic hydrocarbons contributed up to 85.00% of the secondary organic aerosol formation potential (SOAFP), with benzene as the primary species. Positive matrix factorization (PMF) identified four major sources: technological processes and oil/gas volatilization (35.57%), combustion and petrochemical emissions, motor vehicle emissions, and regional background sources. The results underscore the need for targeted control of VOCs from industrial and vehicular sources to mitigate secondary pollution in coastal cities.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3818-4
The electrocatalytic reduction of carbon dioxide (CO2RR) to multi-carbon (C2+) products is of significant interest due to its implications for chemical manufacturing and carbon neutrality. However, the competitive hydrogen evolution reaction (HER) and sluggish C–C coupling kinetics impede selectivity at industrial current densities. Here, we report an interfacial nanoconfinement strategy using N-(2-acetamido)iminodiacetic acid (ADA) to engineer a series of capping layer-covered Cu catalysts (Cu@ADA-x). A volcano-type correlation between capping layer thickness and C2+ selectivity is observed. The optimized Cu@ADA-m catalyst achieves a maximum Faradaic efficiency for C2+ products (FE C2+) of 86.8% and maintains over 80% of its initial FE C2+ after 42 hours at 200 mA cm−2, with an energy efficiency of 38.5%. In-situ Raman spectroscopy and density functional theory (DFT) calculations reveal that the capping architecture stabilizes metastable Cu species and optimizes gas adsorption, enhancing *CO intermediate utilization and lowering C–C coupling energy barriers. This work provides a catalyst design principle for industrial-scale carbon-neutral electrochemical production of multi-carbon products.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3933-9
The global cold chain consumes vast amounts of energy and emits greenhouse gases, while many regions lack proper refrigeration. To address this, we developed a dual-layer electrospun membrane (PZ-PML) for energy-free fruit preservation. The top PVDF-HFP/ZIF-8 layer offers 97.64% solar reflectance and 92.5% mid-infrared emissivity, providing 70 W/m2 radiative cooling. The bottom PAN/MIL-101/LiCl layer, with 2.18 g/g water uptake at 80% RH, delivers ~156 W/m2 evaporative cooling, lowering surface temperature by 6.1 °C under ~400 W/m2 irradiation. The membrane also shows ≥99% antibacterial efficiency against E. coli and S. aureus. Applied to strawberries, it reduced dehydration to 20.2% after 9 days, compared to 68.2% and 74.4% in controls. Additionally, it demonstrates durability, superhydrophobicity, and UV stability. This scalable solution offers energy-free fruit cooling, reducing postharvest losses while maintaining quality and safety.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025021903
Volatile organic compounds (VOCs) are key precursors of secondary organic aerosols (SOA), and their oxidation reactions are regulated by reactive intermediates. A deep understanding of the reaction mechanisms of VOCs-derived reactive intermediates is crucial for evaluating SOA formation. Atmospheric peroxyalkyl radicals (RO2·) are important intermediates produced during VOCs oxidation and can generate highly oxygenated organic molecules (HOMs) through a unique atmospheric autoxidation mechanism, contributing significantly to SOA formation. This article reviews recent advances in computational studies on the autoxidation mechanisms of RO2· with different functional groups, focusing on the autoxidation reactions of RO2· derived from alkanes, alkenes, carbonyl compounds, aromatic hydrocarbons, heteroatom-containing compounds, and other substances. The review highlights the commonalities and differences in autoxidation mechanisms across these functional groups, emphasizing the role of intramolecular hydrogen shifts and subsequent O2 addition steps. Furthermore, we emphasize that future research should focus on the autoxidation of second-generation RO2· and autoxidation mechanisms driven by different intramolecular reactions. Quantum chemical calculations, often combined with kinetic modeling, provide molecular-level insights into reaction pathways and rate constants, which are essential for predicting HOM formation and SOA yields. This review aims to guide further theoretical investigations and support the development of more accurate atmospheric chemistry models.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025022801
Paddy soils are a major source of agricultural methane (CH4) emissions. Biochar is widely applied to paddy soils, while dissolved organic matter (DOM) is ubiquitous; both can regulate CH4 emissions by mediating electron transfer processes, yet their synergistic mechanisms remain unclear. This study investigated the individual and combined effects of biochar and the DOM model compound anthraquinone-2,6-disulfonic acid (AQDS) on CH4 emissions from paddy soil during incubation. Biochar amendment increased DOM concentration and accelerated extracellular electron transfer, resulting in a maximum cumulative CH4 emission of (66.23±16.20) μmol, four-fold higher than the control (15.14±0.18) μmol. In contrast, AQDS addition markedly suppressed CH4 accumulation to (1.04±0.09) μmol, attributed to sulfate introduction as a competitive electron acceptor, despite enhanced electron exchange. The combined biochar-AQDS treatment yielded intermediate CH4 accumulation of (12.71±0.32) μmol. Although DOM availability increased, sulfate-driven electron competition inhibited methanogens, and the combined treatment favored the acetoclastic methanogenesis pathway, which produces less CH4 per unit acetate, resulting in lower emissions than biochar alone but higher than AQDS alone, indicating an additive effect. These findings elucidate the mechanisms by which biochar and DOM jointly regulate CH4 emissions from paddy soils, providing a theoretical basis for agricultural management.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3799-4
Li-rich layered oxides (LLOs) xLi2MnO3·(1−x)LiTMO2 (0 < x < 1, TM = Mn, Ni, Co, etc.) are promising high-energy cathode materials for lithium-ion batteries, capable of achieving energy densities up to 1000 Wh kg−1. However, their practical application is hindered by limited cycle life and voltage decay, primarily stemming from structural instability of Li2MnO3 and LiTMO2 domains during cycling, which manifests as transition metal cation migration, oxygen release, and TM dissolution. This review establishes a comprehensive design and modification scheme based on the fundamental structural unit of LLOs: the LiMn6 hexatomic-ring. In this unit, each Li atom in the TM layer is surrounded by six Mn atoms, forming a π-type hybridization between Mn 3d(t2g) and O 2p orbitals, creating an intact π-bond ring that acts as a distributed redox center. Ordering these functional units into specific spatial configurations can enhance capacity, voltage, and structural stability. However, substituting Mn with other elements breaks the symmetry of the π-bond ring, altering redox behavior and reversibility. The spatial arrangement of LiMn6 rings, representing the arrangement of π-bond rings, is critical for redox activity. In Li2MnO3, the typical honeycomb superstructure of LiMn6 rings is discussed. This review highlights the importance of functional unit ordering in material design, drawing parallels from other systems, and proposes a systematic approach to engineer LLOs for improved electrochemical performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3942-2
Anode-free sodium metal batteries (AF-SMBs) are promising for high-energy, low-cost energy storage, but suffer from interfacial instability due to sluggish Na+ kinetics and non-uniform deposition. Here, we report a scalable electrospinning-pyrolysis route to anchor FeCoNiCuMn high-entropy alloy (HEA) nanoparticles on N-doped carbon nanofibers (HEANCF). Density functional theory (DFT) calculations reveal high binding energy toward Na atoms, facilitating desolvation and adsorption. A built-in electric field (BIEF) arises from work function differences, driving electron redistribution and guiding uniform Na+ diffusion. The heterostructure also shows strong affinity for PF6− anions, promoting NaF-rich SEI formation that suppresses electron tunneling and parasitic reactions. Full cells with Na3V2(PO4)3 cathodes achieve 80% capacity retention after 600 cycles at 1 C. Ah-level pouch cells deliver ~200 Wh kg−1 and retain 87% capacity after 150 cycles at 0.5 C. This work establishes a coherent interfacial-kinetics framework for practical AF-SMBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4148-3
Biological ion channels exhibit multistate transport behavior beyond simple binary open-closed conformations, enabling dynamic control of neural signaling and transmembrane substance transport. Inspired by this, we synthesized a triphenylamine-ketone donor-acceptor (D-A) type poly(aryl amine-ketone) with multiple redox sites, allowing continuously tunable electrochemical states via hierarchical electron transfer. Combining this polymer with two-dimensional conductive MXene, we constructed a biomimetic nanofluidic transistor. Through side-group tuning to optimize redox matching, the polymer undergoes reversible conformation switching via intramolecular charge transfer at voltages below 1 V. The field-driven conformational changes induce electrostatic attraction, promoting reversible contraction of MXene interlayers. Synergistic coupling of interlayer spacing variation and dynamic interfacial charge rearrangement enables precise hierarchical control of ion flux. The device achieves three switchable ion transport states—closed, partially open, and fully open—with an ion switching ratio of 10 and outstanding cycling stability. Furthermore, synaptic plasticity features emulate fundamental attributes of biological signaling, providing a foundation for bioinspired neuromorphic devices.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510034
Phosphonate wastewater, characterized by stable C–P bonds, poses significant environmental risks due to its resistance to degradation and potential to contribute to eutrophication. This study developed a chloride-enhanced Fe(II)/PMS/H2O2 system for the oxidative degradation of 2-phosphonobutane-1,2,4-tricarboxylic acid (PBTC) and simultaneous recovery of phosphorus as iron phosphate (FePO4). Under optimal conditions (0.1 mmol/L PBTC, 1.0 mmol/L Fe(II), 0.5 mmol/L PMS, 0.5 mmol/L H2O2, 10 mmol/L NaCl, initial pH 3.0, 60 min), total phosphorus (TP) removal reached 100%, with phosphorus nearly completely recovered as FePO4 precipitate. Increasing NaCl concentration and temperature enhanced TP removal, while pH significantly influenced removal efficiency and product speciation; acidic conditions (pH < 4.3) favored FePO4 precipitation. Coexisting Ca2+ and Mg2+ had negligible effects, whereas HCO3− and humic acid (HA) inhibited TP removal in a concentration-dependent manner. Radical quenching and electron spin resonance (ESR) analyses identified hydroxyl radicals (•OH), ferryl ion (Fe(IV)=O), sulfate radicals (SO4•−), and chlorine radicals (Cl•) as primary reactive species, with •OH playing a dominant role. Chloride introduction promoted the generation of multiple reactive species, and Cl• and its derivative Cl2•− directly attacked the C–P bond and phosphonate group, facilitating phosphorus release as PO43− and subsequent FePO4 formation. The system's feasibility was validated using actual industrial circulating cooling water. This study provides a novel approach for phosphonate wastewater treatment and phosphorus recovery.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510056
To support the construction of an ecologically clean small watershed in Harbin, a pilot-scale trial of sediment elutriation was conducted in the Hejia Ditch to evaluate its effectiveness in controlling endogenous pollution and to elucidate the underlying mechanisms. After treatment, sediment organic matter, total nitrogen (TN), and total phosphorus (TP) decreased by 5.11%, 10.19%, and 8.71%, respectively. Water transparency, dissolved oxygen (DO), and oxidation-reduction potential (ORP) increased by 102.46%, 11.07%, and 15.66%, while chemical oxygen demand (COD) and ammonia nitrogen (NH4+-N) removal rates reached 35.67% and 22.65%. The technology effectively removed surface suspended sediment, leaving a stable layer of coarse inorganic particles that formed a clear mud-water interface. Post-treatment, clay content decreased by 8.87%, sand content increased by 12.37%, and median (D50) and 90th percentile (D90) particle sizes increased by 32.39% and 159.97%, respectively. Mechanical disturbance and particle size redistribution enhanced oxygen transfer at the interface, increasing the abundance of facultative anaerobic phyla such as Chloroflexi and Spirochaetes, thereby suppressing the generation of odorous gases (H2S, NH3) and preventing sediment resuspension. Increased microbial diversity and richness improved ecosystem stability and self-purification capacity. These results demonstrate that sediment elutriation is an effective method for controlling endogenous pollution in Hejia Ditch, providing a scientific basis for ecological restoration and long-term management.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60648-2
The influence of mixing modes on the integrated process of co-pyrolysis of Naomaohu coal (NMH) and elm (ELM) with CO2 reforming of methane (CP-CRM) was investigated over Ni-based catalysts prepared by ball milling. Three mixing modes—NMH/ELM, ELM/NMH, and Blends—were examined and compared with co-pyrolysis under N2 (CP-N2). Results show that product distribution was significantly affected by mixing mode. The Blends mode achieved the highest tar yield, increasing by 35.29% compared with CP-N2. Light oil content in tar was higher, while pitch content was lower for Blends relative to layered modes. Phenols content in tar from Blends was 19.52% higher than CP-N2, and free radical concentration in tar was higher, attributed to enhanced heat and mass transfer between particles by mechanical mixing, promoting complete pyrolysis and efficient utilization of hydrogen-rich free radicals (·H, ·CHx) to suppress secondary cracking and polymerization. In contrast, NMH/ELM mode in CP-CRM improved phenols content by 33.27% over CP-N2. Free radical concentration in tar during CP-CRM was lower than in CP-N2, indicating timely stabilization of pyrolysis radicals by reforming-generated radicals. These findings provide guidance for regulating tar yield and composition in co-pyrolysis processes.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026020207
Although the production and use of hexabromocyclododecanes (HBCDs) have been completely banned in China since December 2021, historical production activities may still leave high-concentration residual contamination in localized areas. This study investigated a typical legacy site of historical HBCDs production in eastern China. Surface and core soil samples were systematically collected both inside and outside the former plant area to characterize the occurrence, spatial distribution, and environmental burden of HBCDs, and to evaluate associated human health risks. Results showed that HBCD concentrations in soils outside the plant area ranged from below detection limit to 6.90×10² ng·g⁻¹ dw, while those inside the plant area were substantially higher, reaching up to 1.18×10⁶ ng·g⁻¹ dw. γ-HBCD was the dominant isomer; however, its relative abundance was lower than that reported in commercial HBCD mixtures and in previous studies conducted near production facilities. Outside the plant, HBCDs concentrations in soil generally decreased with increasing distance from the site, yet remained detectable at a distance of approximately 10 km (15.2 ng·g⁻¹ dw). Within the plant area, HBCDs concentrations in soil cores decreased with depth, declining from 1.08×10⁴–1.18×10⁶ ng·g⁻¹ dw in surface soils to 1.05–93.5 ng·g⁻¹ dw at depths of about 4 m. Analysis of the relative cumulative environmental burden indicated that although HBCDs loads were highest in the near-source area, they gradually accumulated over a broader spatial scale. Approximately 23.7%, 40.1%, 60.0%, and 87.1% of the total estimated burden accumulated within 2 km, 2.81 km, 4 km, and 6 km from the site, respectively. Health risk assessment indicated that oral ingestion of soil was the primary exposure pathway for different populations. Localized high-contamination zones within the plant area contributed significantly to non-carcinogenic risks, while overall risks for children outside the plant area were at acceptable levels.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026022502
This study investigates the effects of different land use types on topsoil carbon (C) and nitrogen (N) contents and their spatial distribution in the lower reaches of the Sancha River Basin, a karst region of the Yunnan-Guizhou Plateau. Grid sampling collected 0–20 cm topsoil from forestland (n=23), cultivated land (n=25), and grassland (n=32). Total C and N were measured. Results showed that topsoil C content followed grassland (40.36±22.92 g·kg−1) > forestland (37.05±12.83 g·kg−1) > cultivated land (34.06±14.57 g·kg−1), while N content followed forestland (2.89±0.76 g·kg−1) > grassland (2.67±1.19 g·kg−1) > cultivated land (2.50±0.65 g·kg−1). One-way ANOVA revealed no significant differences among land use types (P>0.05). Soil C and N were significantly positively correlated across all land uses (r>0.5, P<0.001). Coefficient of variation (CV) indicated grassland had the highest C variability (0.57), while forestland showed the most stable C and N (CV=0.35 and 0.26, respectively). Cultivated land had CVs of 0.43 for C and 0.26 for N. Spatially, forestland exhibited concentrated high C values with significant N heterogeneity; grassland had higher C in southern and eastern areas but scattered distribution, with generally low and variable N; cultivated land showed uniform but lowest C and N. Land use types significantly drive topsoil C and N dynamics through vegetation input, soil disturbance, and management practices, underscoring the importance of rational land use planning for enhancing carbon sink functions and sustainable development in karst watersheds.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025031202
Manganese-rich constructed wetlands (CWs) have emerged as an effective strategy for enhanced nitrogen removal, yet current understanding of their denitrification mechanisms remains limited to speculative interpretations of microbial community structures. This study developed a novel CW-MFC system integrating manganese ore (MO) and activated carbon (AC) substrates with microbial fuel cell (MFC) technology to investigate the manganese-nitrogen coupling biochemical metabolism. It was systematically evaluated the effects of influent organic carbon concentrations on nitrogen removal performance and elucidated the mechanisms of electron transfer and their coupling with nitrogen removal pathways through multi-dimensional analyses, including functional enzymes, extracellular polymeric substances (EPS) characterization, intra-/extracellular electron transfer-related gene expression, and electron transport activity. Results showed that the synergistic integration of MO, AC, and MFC configuration significantly enhanced nitrogen removal efficiency, with ammonium removal reaching up to 5.5 times that of the control group. The functional substrates notably upregulated enzyme activities of nitrogen transformation in biofilms while stimulating nitrification and anammox processes at the anode. EPS analysis revealed that Mn2+ derived from manganese reduction was captured by EPS, thereby facilitating the manganese cycling. Concurrently, the increased abundance of electron transport chain (ETC) and extracellular electron transfer (EET) genes, coupled with increased cytochrome C (Cyt-C) concentration and activity, confirmed enhanced EET performance. It indicated that the coordinated EET network among electrodes, microorganisms, MO, and AC serves as critical electron mediators for nitrogen transformation. This study provides mechanistic insights into manganese-carbon coupled CW-MFC systems regarding nutrient removal, biogeochemical cycling, and electron transfer dynamics, advancing fundamental knowledge for the development and application of manganese-rich constructed wetland technology.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607013
This study investigated the synergistic effects of earthworm mucus and two biochar types (rice husk biochar and straw biochar) on heavy metal bioavailability during sludge composting. Sludge was amended with earthworm mucus alone or combined with biochars at varying proportions, and the impacts on physicochemical properties, total heavy metal concentrations, bioavailable fractions, and chemical speciation were analyzed. Results showed that mucus addition increased sludge pH and electrical conductivity (EC) but decreased total nitrogen (TN) and total phosphorus (TP) contents. Synergistic mucus-biochar composting further elevated pH and EC while reducing TN, with the optimal treatment being mucus plus 10% rice husk biochar. Mucus-only composting reduced total concentrations and bioavailability of Cd, Cu, Ni, Zn, and Pb. Adding biochars significantly enhanced these reductions. Specifically, mucus with rice husk biochar achieved the best Cd removal, with total and bioavailable Cd decreasing by 27.03%–55.68% and 9.52%–28.57% (P<0.05), respectively, compared to controls. Mucus with straw biochar was most effective for Ni, Zn, and Pb, reducing total contents by 3.81%–5.72%, 7.93%–34.62%, and 42.61%–79.46%, and bioavailable fractions by 2.90%–26.31%, 15.58%–24.14%, and 32.30%–36.88% (P<0.05), respectively. Speciation analysis revealed that Cd, Ni, and Pb carbonate-bound fractions transformed into residual forms, and exchangeable fractions shifted to Fe-Mn oxide-bound forms. Straw biochar addition resulted in the highest residual fractions for Cd, Cu, Ni, Zn, and Pb, increasing by 0.35%–7.02%, 8.61%–12.90%, 16.62%–23.02%, 17.33%–26.10%, and 16.12%–27.20% (P<0.05), respectively. These findings demonstrate that earthworm mucus combined with rice husk or straw biochar effectively reduces heavy metal concentrations and bioavailability in sludge, offering a promising strategy for sludge composting.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3981-7
Solution-processable quasi-2D perovskites are promising laser gain media due to their high exciton binding energy and improved stability relative to 3D counterparts. However, conventional synthesis yields mixed n-value phases, introducing interfacial defects and energetic disorder that impede charge injection into desired emission centers. Here, we report the first demonstration of stimulated emission from a phase-pure quasi-2D perovskite (n=8) achieved via a solvent-sieving method for selective phase removal. This dynamic purification yields near-unity phase purity (99.85%) with no detectable low-n phases, as confirmed by X-ray diffraction and ultraviolet-visible spectroscopy. The phase-pure film exhibits a narrower and more intense (001) diffraction peak (FWHM 0.16 nm, intensity 16,129) compared to pristine films (FWHM 0.22 nm, intensity 3,304), indicating enhanced crystallinity and increased grain size. Time-resolved photoluminescence reveals a prolonged carrier lifetime of 6.98 ns, suggesting reduced trap density. Atomic force microscopy shows a nearly pinhole-free surface with root mean square roughness of 1.18 nm. Consequently, the amplified spontaneous emission threshold is reduced to 13.82 μJ cm−2, a 12.5% improvement over conventional mixed-phase films (15.8 μJ cm−2). This work provides an efficient route to pure-phase quasi-2D perovskites for low-threshold lasers.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607025
The Holocene alluvial-diluvial stratum of the Quaternary is characterized by high soil hydraulic conductivity and intense surface water-groundwater interaction, which leads to rapid and extensive migration of contaminants from landfills. To investigate the contaminant characteristics of a municipal solid waste (MSW) landfill in such strata, a case study was conducted at a landfill in southwestern China. Methods including the Nemerow pollution index and the potential ecological risk index were employed to systematically analyze the contamination of groundwater and soil, as well as the spatial distribution of organic matter and heavy metals. The results showed that the groundwater was severely contaminated (PI > 3). The maximum exceedance multiples for total bacterial count, ammonia nitrogen (NH4+-N), and total coliforms relative to the standard limits were 36, 9.5, and 8, respectively. The composition of the contaminants in groundwater was highly consistent with the characteristics of landfill leachate. For the soil, the concentrations of six heavy metals (Cu, Pb, Cd, Ni, Hg, and As) were all below the Class II screening values of the standard GB 36600—2018. Both the Nemerow pollution index (PI < 0.7) and the potential ecological risk index (RI < 150) indicated that the soil environment was safe. Regarding soil dissolved organic matter (DOM), humic-like substances (22.9% to 34.9%) and fulvic-like substances (22.4% to 27.5%) were the dominant components, and their fluorescence intensities exhibited an exponential decay trend with increasing soil depth. The speciation of Cu, Pb, As, Hg, and Ni was dominated by the residual fraction (52.33% to 90.32%). However, over 70% of Cd existed in active forms (exchangeable + Fe/Mn oxide-bound), suggesting a high migration risk. The horizontal distribution of heavy metals showed regional specificity, with high-value areas mainly concentrated in the screening waste and soil stacking areas. Vertically, Cu and Cd exhibited surface enrichment, while As, Hg, Pb, and Ni were enriched in the groundwater fluctuation zone. These findings indicate that groundwater in alluvial-diluvial strata is highly susceptible to leachate contamination, while soil heavy metal contamination is not significant, with low levels in the aquifer but a tendency to accumulate at the water-soil interface. It is recommended that during landfill remediation, attention be paid to anti-seepage measures in waste excavation and stacking areas, as well as the interception and remediation of the groundwater fluctuation zone, to prevent secondary contamination of soil and groundwater.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607024
This study systematically investigated the effects of single and composite conditioning with lysozyme, amylase, and protease on sludge dewatering performance and carbon source recovery in filtrate from residual sludge of a water treatment plant in Foshan City. Results indicated that lysozyme significantly improved sludge dewatering by reducing specific resistance of filtration (SRF), capillary suction time (CST), and water content of the filtered sludge cake (Wc). While amylase and protease decreased Wc, they elevated SRF and CST, deteriorating sludge filtration properties. Among combined enzyme treatments, lysozyme and protease exhibited synergistic effects. The asynchronous addition strategy (protease/amylase followed by lysozyme) demonstrated the best performance in reducing Wc, while simultaneous addition was more effective in improving SRF and CST. Mechanistic analysis revealed that all three enzymes reduced sludge particle size. Lysozyme primarily targeted cell lysis and wall disruption, releasing intracellular substances, reducing viscosity, and enhancing sludge hydrophobicity. Meanwhile, amylase and protease mainly disrupted extracellular polymeric substances (EPS), leading to release of proteins and polysaccharides into slime EPS, increasing viscosity and hydrophilicity. Furthermore, all three enzymes effectively promoted carbon source release, increased soluble chemical oxygen demand (SCOD) of filtrate, and transformed recalcitrant humic acid-like organic matters into readily bioavailable tryptophan-like and tyrosine-like substances. These findings provide a basis for optimizing enzyme-based sludge conditioning to achieve simultaneous dewatering enhancement and carbon source recovery.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3966-0
The development of low platinum-loading catalysts for the economically viable hydrogen evolution reaction (HER) remains challenging. Herein, a precursor dilution strategy is used to fabricate Pt nanoclusters anchored on Ni-embedded porous carbon microspheres. The approach begins with the facile synthesis of Zn/Ni-based coordination polymers (Ni-BTC-Zn) due to the isomorphic substitution of Zn2+ and Ni2+. During pyrolysis, the evaporation of zinc species results in a highly porous carbon structure with well-dispersed nickel nanoparticles. Subsequent solvothermal treatment allows for the uniform deposition of Pt nanoclusters to form the final bimetallic PtNi catalysts (PtNi-BTC-C). Among them, the optimized PtNi-BTC-C10 exhibits exceptional alkaline HER performance, requiring an overpotential of only 41 mV to achieve 10 mA cm−2 and a low Tafel slope of 31.1 mV dec−1. It also demonstrates outstanding durability with a current retention of 90.7% after 70 h, far exceeding Pt/C. Extensive characterization confirms that moderate Zn dilution optimally modulates the Ni particle size and dispersion, leading to maximized active sites and enhanced charge transfer. Combined with DFT calculations, the Pt-Ni-cluster model for PtNi-BTC-C10 possesses an optimized electronic structure with a shifted d-band center, which facilitates water dissociation and optimizes H* desorption with the most favorable energetics (0.262 eV). This work provides a fundamental understanding of precursor dilution engineering and offers a versatile pathway for designing advanced noble-metal-based bimetallic electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3967-x
Metal-halide perovskites exhibit exceptional optical gain, narrow emission linewidths, and high emission efficiency, positioning them as promising candidates for next-generation lasers. Thermal evaporation, a mature semiconductor fabrication technique, offers scalability, yet monitoring phase distribution during deposition remains challenging. This study systematically investigates and regulates thermally evaporated FAxCs0.8PbBr3 perovskite films by tuning formamidinium (FA) content to optimize phase distribution. At intermediate FA content, films achieve a balanced distribution of n=2 to n=5 quantum-well phases, facilitating ultrafast carrier transfer (<0.31 ps) and suppressing nonradiative recombination. FA+ actively incorporates as an A-site cation, promoting ordered crystallization and reducing defect densities. The optimized films exhibit a net modal gain of 1041 cm−1 and a gain lifetime of 129 ps. Benefiting from efficient internal scattering, the threshold for cavity-free random lasing is reduced to below 5 μJ/cm2 at room temperature. The low spatial coherence of random lasing enables speckle-free imaging with a speckle contrast as low as 0.011 and improved contrast-to-noise ratios across all spatial frequencies. This work provides a scalable strategy for perovskite composition-phase engineering, advancing speckle-free laser imaging systems compatible with semiconductor-grade, large-area manufacturing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3984-5
Rechargeable aluminum batteries (RABs) are promising for large-scale energy storage due to high theoretical capacity, inherent safety, and abundant aluminum reserves. However, conventional AlCl3-based ionic liquid electrolytes suffer from high cost, uncontrolled dendrite growth, and severe anode corrosion. Here, a molecular-level ligand engineering strategy is proposed, employing nitrogen-containing cyclic amides with tunable N–H functionalities to modulate the coordination environment of deep eutectic electrolytes (DEEs). Combined experimental and theoretical investigations reveal that the α-pyrrolidone-based DEE (PDEE) possesses a wider electrochemical window, higher ionic conductivity, and lower polarization. Precise N–H regulation optimizes cationic ligand and chloroaluminate anion interactions, accelerating ion transport to facilitate uniform Al deposition without dendrites. The amine functionalities enable in situ construction of a uniform inorganic-organic bilayer solid electrolyte interphase, mitigating anode corrosion and enhancing long-term interfacial stability. As a result, Al//Al symmetric batteries with PDEE achieve stable cycling for over 2000 hours, while Al-graphite full batteries demonstrate negligible capacity decay after 6000 cycles. This study establishes that ligand molecular engineering offers an effective strategy for optimizing DEEs, enabling durable and high-performance RABs.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512059
Recovery of palladium from Pd-bearing wastewater is economically and environmentally significant. Adsorption is a promising method due to its simplicity, low cost, and high efficiency. In this study, a novel thiol-modified adsorbent (CHT-SH) was synthesized via one-step functionalization of inexpensive chitin (CHT) with thioglycolic acid. At room temperature and pH=2, CHT-SH exhibited an experimental adsorption capacity of 223.67 mg·g−1 for Pd(II), which was approximately 7 times higher than that of pristine CHT (30.6 mg·g−1). Kinetic and isotherm studies indicated that the adsorption process followed the pseudo-second-order kinetic model and the Langmuir isotherm model, with a maximum theoretical adsorption capacity of 248.89 mg·g−1, suggesting monolayer chemisorption. Characterization (FTIR, SEM, XPS, XRD) and density functional theory (DFT) calculations revealed that the adsorption mechanism primarily involved synergistic coordination of nitrogen and sulfur atoms, along with electrostatic interactions. Furthermore, CHT-SH demonstrated good reusability, retaining stable adsorption capacity after five adsorption-desorption cycles. Compared to other adsorbents that rely on redox mechanisms and are costly, CHT-SH offers comprehensive advantages. This work provides a cost-effective and efficient adsorbent for Pd(II) recovery from wastewater, offering technical support and theoretical reference for practical applications.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512014
Mining activities cause severe soil degradation and microbial diversity loss, impeding ecological restoration. This study evaluated the effects of a novel soil amendment, microporous bio-gravel (MBG), on bacterial and fungal community structure and function in degraded soil from the Baiyinhua open-pit mine, Inner Mongolia. A pot experiment with four MBG-to-soil volume ratios (CK, L=1:3, M=1:2, H=1:1) was conducted, with a simplified plant community and uniform fertilization. After 180 days, soil samples were analyzed via high-throughput sequencing and bioinformatics. Results showed that the medium ratio (M) significantly increased fungal Shannon index and evenness, while the high ratio (H) negatively affected bacterial communities. At phylum and genus levels, MBG promoted enrichment of Cyanobacteria and specific functional groups (e.g., nitrogen-fixing bacteria, Bacillus). Co-occurrence network analysis revealed peak complexity, modularity, and average degree in bacterial and fungal networks under the M treatment. Functional prediction indicated significant enrichment of pathways related to lipopolysaccharide biosynthesis, nitrotoluene degradation, and plant-pathogen interactions, alongside increased abundance of saprotrophic and ectomycorrhizal fungi. Mantel and VPA analyses showed that MBG indirectly regulated microbial community structure by improving soil physicochemical properties and plant traits, with stronger effects on fungi than bacteria. In conclusion, MBG optimizes the soil microhabitat and plant-soil-microbe interactions, modulating microbial diversity, network complexity, and functional potential. The medium ratio (1:2) was most effective, demonstrating potential for ecological restoration of degraded mine soils.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510017
Municipal solid waste (MSW) is a significant source of urban carbon emissions. This study integrates life cycle assessment (LCA) and system dynamics (SD) to construct a multi-subsystem LCA-SD model covering economy, population, waste generation, transportation, treatment, and resource utilization, using Fuzhou City as a case study. The model was validated against historical data and uncertainty analysis. Carbon emissions from MSW transportation, treatment, and resource utilization during 2013–2023 were calculated, and emission trends under seven reduction scenarios for 2024–2035 were predicted. Results show that Fuzhou's MSW treatment evolved through three stages: 'landfill+incineration', 'treatment structure adjustment', and 'incineration+kitchen waste resource utilization', corresponding to emission growth, fluctuation, and reduction periods. In 2023, total net carbon emissions were 1.07×10^6 t CO2-eq, with incineration being the largest contributor (9.93×10^5 t), followed by transportation (2.93×10^4 t), leachate treatment (2.14×10^4 t), and kitchen waste treatment (7.90×10^3 t, negative emission). Scenario analysis indicates that without further measures, carbon neutrality cannot be achieved. Synergistic enhancement of kitchen waste separation and incineration power generation efficiency can significantly boost reduction, potentially achieving carbon neutrality by 2032. The study provides a dynamic accounting and scenario assessment framework for low-carbon transition of urban solid waste systems.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60665-2
Levulinic acid (LA) is a promising platform product with wide industrial applications. Efficient conversion of cellulose into LA has become a research hotspot, yet traditional experimental optimization is time-consuming and inefficient. This study integrates multidimensional data—reaction conditions, solvent properties, and physicochemical characteristics of metal salts—to construct a systematic dataset. Six machine learning models (decision tree, gradient boosting regression, K-nearest neighbors, multilayer perceptron, random forest, and support vector machine) were developed to predict LA yield. The gradient boosting regression (GBR) model achieved the best performance, with a test-set determination coefficient (R²) of 0.94 and the lowest root-mean-square error (RMSE). SHapley Additive exPlanations (SHAP) and partial dependence analysis identified water fraction, catalyst dosage, and reaction temperature as the key factors influencing LA formation. By integrating the GBR model with particle swarm optimization (PSO), RuCl₃ was identified as an efficient catalyst under high-temperature and short-reaction-time conditions. This study demonstrates the potential of machine learning in cellulose conversion research, providing a data-driven strategy and theoretical guidance for efficient and green LA production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4065-6
Industrial-scale hydrogen production from seawater is a paramount goal for a sustainable energy future, yet it is severely hampered by the rapid deactivation of electrocatalysts under harsh operating conditions. Here, we introduce a robust self-supporting aerogel catalyst designed to address the two intertwined challenges of activity and stability in high-current-density seawater electrolysis. Our strategy involves creating strong metal-support interactions by anchoring ultrasmall platinum nanoparticles onto a porous N-doped carbon aerogel (Pt@N/CFP). Theoretical calculations reveal that this unique Pt-N interface serves a dual critical function: it not only lowers the kinetic barrier for water dissociation but also creates an electronic shield that effectively prevents chloride ion poisoning of the Pt active sites. When implemented as the cathode in a practical anion-exchange membrane (AEM) electrolyzer, the Pt@N/CFP catalyst demonstrates exceptional performance, achieving a low cell voltage of 1.688 V at an industrial-grade current density of 1000 mA cm−2 and maintaining outstanding stability for over 300 h. This work provides guidance for creating exceptionally durable catalysts capable of withstanding extreme electrochemical environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4015-5
Mechanochromic photonic crystals are promising for smart optical materials due to their tunable photonic stop band. Here, we report interface-engineered transparent and mechanochromic non-close-packed photonic crystals (NPCs) by incorporating polystyrene@vinyl-modified SiO2 (PS@V-SiO2) nanospheres (n_PS=1.59, n_V-SiO2=1.46) into a photocurable phenoxypolyethylene glycol acrylate (PEGPEA) matrix (n_PEGPEA=1.52). The nanospheres formed solvation-mediated liquid NPCs in the precursor. Ultraviolet (UV) curing promoted copolymerization between surface C=C bonds of nanospheres and the matrix, which reduced interfacial scattering and enabled highly transparent NPC films. Meanwhile, non-uniform polymer shrinkage led to variations in the ordering of nanospheres, especially in structures with a low volume fraction (φ ≤ 0.23). Under external strain (ε: 0–64%), the film exhibited a dynamic color response. Initially, stretching enhanced the ordering of the nanospheres and the reflection intensity of NPCs, thereby activating the structural color. Further deformation, however, introduced defects and reduced the reflectivity. A blue shift of ~213 nm was achieved in an NPC (φ = 0.23) fabricated by 170 nm of PS@V-SiO2 nanospheres, accompanied by a color gradient from red to blue. Comparisons across SiO2–poly(ethylene glycol) diacrylate (PEGDA, n_PEGDA=1.45), SiO2–PEGPEA, and PS@V-SiO2–PEGDA NPC systems highlighted the key role of interfacial scattering, which is affected by the synergistic effects of interfacial covalent polymerization, refractive index matching between the elastomer matrix and nanospheres, and the crosslinking density. This work demonstrates spectrally tunable mechanochromism via size control and patterned anti-counterfeiting labels, thereby providing insights for designing advanced anti-counterfeiting materials applicable in flexible electronics and displays.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4007-x
Hydrogels, with their hydrophilicity, flexibility, and environmental friendliness, are highly desirable for moisture-electric generators (MEGs) that harness ubiquitous moisture to generate electrical energy. As the active material layer in MEGs, hydrogels play a crucial role in absorbing atmospheric moisture and converting chemical potential energy into electricity. However, the relatively low output current of the device and the instability of hydrogels pose challenges to the development of high-performance hydrogel-based MEGs. Herein, we introduce a straightforward, feasible, cost-effective, and versatile two-step solvent displacement strategy to overcome the barrier associated with the development of MEGs. Through tunable solvent interactions of glycerol and water, the moisture absorption capability and stability of the hydrogel can be improved, while promoting favorable ion migration. Such an effective processing route not only significantly boosts the output performances but also greatly improves the long-term durability of hydrogel-based MEGs. Notably, the current output and power density of the treated MEGs can increase by up to two orders of magnitude. The mechanisms behind the intriguing observation are investigated by various characterizations and theoretical calculations. This universal strategy holds promise to be extended to various hydrogel-based MEGs. Moreover, the MEGs can be used for energy harvesting, self-powered respiratory monitoring, and non-contact humidity detection. This work offers new opportunities for advancing green energy and self-powered technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3968-3
The commercialization of perovskite solar cells (PSCs) is hindered by stability issues primarily stemming from interfacial defects. This study employed a machine learning (ML) screening approach and constructed a learnable weighted ensemble model (LWEM) to enhance prediction robustness for identifying effective interface passivation materials. The ML model predicted that an imidazolium salt-based interface modifier, 1-benzyl-3-methylimidazolium tetrafluoroborate (BMT), is suitable for planar n-i-p PSCs. Subsequent experimental results demonstrated that BMT provides synergistic passivation via an 'ion-coordination dual-lock' mechanism that significantly suppresses non-radiative recombination, facilitates hole extraction, and improves the quality of the perovskite film. The BMT-modified devices achieve a significant increase in power conversion efficiency (PCE) from 22.45% to 24.89% under AM 1.5G illumination, and attain a high PCE of 41.31% under 1000 lux light emitting diode (LED) indoor lighting. Additionally, the modified devices exhibit outstanding stability under long-term storage and maximum power point tracking conditions. This work provides a strategy for developing high-performance and highly stable PSCs for both indoor and outdoor applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4030-y
In the era of artificial intelligence, efficient perception and processing of massive visual information demand advanced machine vision systems. Inspired by human visual adaptation, various optoelectronic devices have been developed, yet most rely on external gate voltages or complex circuits for dynamic sensitivity modulation. This work demonstrates an all-optically controlled biomimetic sensor based on a one-dimensional ZnO/MAPbBr3 heterojunction, achieving both positive and negative photoconductivity effects. By modulating oxygen vacancy states with ultraviolet light, the competition between intrinsic photoconduction and trap-mediated carrier capture is regulated, enabling dynamic control of visible-light photoresponse within a single device. This tunable behavior mimics scotopic adaptation (photopigment regeneration under weak illumination), photopic adaptation (photopigment bleaching in bright environments), and eyelid-like self-protection against intense light. The device operates without external gate bias or cascaded circuits, offering a promising strategy for next-generation intelligent biomimetic sensors in machine vision.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60692-5
Long persistent luminescence materials (LPLMs) have demonstrated significant potential in photo- and electro-catalysis due to their unique capability of storing and controllably releasing photogenerated charge carriers. These materials offer innovative solutions for environmental remediation and sustainable energy technologies. This review systematically summarizes recent advances in the application of LPLs in photo- and electro-catalysis, outlining their developmental history and underlying mechanisms. Emphasis is placed on their applications in organic pollutant degradation, photocatalytic hydrogen evolution, and photovoltaic cells. Furthermore, design strategies and research frameworks for LPLs are discussed. The current limitations and challenges in this field are examined, and future research directions are proposed to facilitate the transition of LPLMs from fundamental research to practical applications in energy and the environment. Key materials such as SrAl2O4:Eu2+,Dy3+ exhibit afterglow lasting up to 30 hours, enabling round-the-clock catalytic activity. Composite systems like g-C3N4@Au@SrAl2O4:Eu2+,Dy3+ and Cu|CuO/SrAl2O4:Eu2+,Dy3+ have achieved efficient degradation and simultaneous hydrogen evolution. Z-scheme heterojunctions, e.g., Sr2MgSi2O7:Eu2+,Dy3+/Ag3PO4, demonstrate enhanced performance. The review highlights the potential of LPLMs to overcome the limitation of intermittent light sources, providing a pathway for continuous catalytic processes.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60708-6
Mercury emissions from coal combustion are highly toxic, volatile, and bioaccumulative, posing long-term threats to ecosystems and human health. This review systematically examines the current status and control policies of mercury emissions from coal combustion in China, analyzing distribution characteristics and transformation mechanisms during combustion, with emphasis on collaborative removal in pollution control devices after ultra-low emission retrofitting. A progressive strategy of 'synergistic enhancement–deep purification–resource recycling' is proposed, comprising three tiers: optimizing operational parameters of existing control systems to enhance synergistic mercury removal; developing efficient adsorption and catalytic oxidation technologies for industrial application; and advancing integrated mercury removal and recovery technologies, such as magnetosphere-based sorbents and recovery processes, focusing on high-value utilization. The paper also outlines future research directions aligned with international compliance and domestic environmental tax policies, providing theoretical and technical support for China's commitments to near-zero emissions of coal combustion pollutants.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4149-1
Large optical anisotropy is paramount for efficient light manipulation in optoelectronic devices. Van der Waals layered materials, exhibiting large structural contrast between in-plane and out-of-plane directions, are inherently anisotropic in 3D space. However, measurements of their optical constants have been limited to 2D planes. Here, we directly measure reflectance spectra from the edge and basal surfaces of layered MoS2, NbOCl2, and WTe2 crystals to compare out-of-plane and in-plane optical constants in the 500–1000 nm range. Results show that out-of-plane refractive indices are smaller than in-plane values. Out-of-plane extinction coefficients are zero for MoS2 and NbOCl2 but nonzero for WTe2, confirmed by transient reflection spectroscopy. The nonzero extinction in WTe2 arises from symmetry of transition dipole moments and density of states dictated by crystal structure. Out-of-plane optical constants of MoS2 and NbOCl2 exhibit less dispersion than in-plane, whereas WTe2 shows enhanced out-of-plane dispersion around 2.14 eV, attributed to increased optical transition probability from larger density of states. These parameters indicate giant birefringence (>1.8 for MoS2, >0.6 for NbOCl2, >0.5 for WTe2) and linear dichroism (up to 100% for MoS2 and NbOCl2, 40.7% for WTe2) on edge surfaces. Results enable prediction of optical response at arbitrary incidence angles, aiding polarization-related optoelectronic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4173-x
Ferroelectric memory, with its promise of low power consumption, high writing speed and exceptional endurance, requires the scaling of ferroelectric films to ultrathin dimensions—often just a few atomic layers thick. However, such extreme thinning risks destabilizing or even erasing electric polarization, mainly due to the detrimental depolarization field. Remarkably, certain ferroelectrics exhibit an intrinsic immunity to this effect, as predicted theoretically and confirmed experimentally. Examples include improper ferroelectrics, hyper ferroelectrics, engineered heterostructures, and low-dimensional van der Waals ferroelectrics. This review systematically examines these unique materials, unravelling the fundamental physics behind their polarization robustness and the mechanisms enabling them to resist the depolarization field. By bridging theory with experimental advances, we aim to inspire the design of next-generation ferroelectrics capable of overcoming critical challenges encountered in practical ferroelectric memory devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4123-0
Aqueous aluminum-ion batteries (AAIBs) are promising for large-scale energy storage due to safety, sustainability, and theoretical high capacity. However, sluggish electron/ion transport in conventional cathodes limits rate capability. Here, we first propose high-entropy engineering of metal oxides (HEOs) as cathodes in AAIBs, leveraging the 'cocktail effect' and abundant electron transport pathways to enhance rate-capacity. Atomic-level interactions between different metal atoms broaden the d-band with reduced electronic level degeneracy, facilitating rapid electron transport, achieving one of the best rate capabilities (119.4 mAh g−1 at 10.0 A g−1) among metal-oxide cathodes. The disordered layered oxides formed with a high-entropy framework alleviate electrostatic repulsion between aluminum ions and the fixed lattice, mitigating structural degradation and imparting excellent cycling stability (over 95.1 mAh g−1 after 500 cycles at 2.0 A g−1). The optimized HEO-Cr cathode (Fe0.6Co0.6Ni0.6Mn0.6Cr0.6O4) exhibits outstanding rate performance and cycling stability. DFT simulations and electrochemical tests reveal that multi-transition metal incorporation, bandgap narrowing, and unique lattice structure drastically enhance electron transport efficiency. The layered phase formed after cycling, based on a high-entropy framework, overcomes challenges from high charge density aluminum ions, significantly enhancing cycling stability. This work paves the way for high-performance AAIBs and other aqueous multivalent metal ion batteries by rationally designing high-entropy engineering.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4131-3
p-n heterojunction solar-blind photodetectors based on p-type materials and n-type Ga2O3 have attracted significant attention in optoelectronics due to their inherent low dark current and self-powered operation. Organic-inorganic hybrid heterojunctions integrating p-type organic materials with n-type Ga2O3 offer a promising solution to overcome lattice mismatch, enabling device performance breakthroughs. In this work, Ga2O3 thin films were treated via a supercritical fluid (SC) technique, which significantly reduced defect state density while improving crystallinity and surface uniformity, laying a foundation for heterojunction interface optimization. Simultaneously, a self-assembled monolayer (SAM) was introduced at the organic-inorganic heterojunction interface. The high-quality Ga2O3 surface engineered via SC treatment facilitated efficient, oriented self-assembly of SAM molecules, enabling precise modulation of interfacial energy band alignment and promoting separation and transport dynamics of photogenerated carriers. Benefiting from synergistic SC modification and SAM functionalization, the fabricated solar-blind photodetector achieved a highest responsivity of 111.7 mA/W and a specific detectivity of 1.02 × 10^11 Jones under zero bias (self-powered mode) and weak 254 nm light with an intensity of 5 μW/cm2. These results demonstrate a viable route to high-performance, self-powered solar-blind photodetectors through interface engineering.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4117-y
Real-time, in situ imaging of hydrogen peroxide (H2O2), a key reactive oxygen species implicated in various diseases, remains challenging due to limitations of existing probes, such as short emission wavelengths and reliance on external excitation. To address these issues, we developed an H2O2-triggered near-infrared (NIR) chemiluminescence (CL) nanoprobe with aggregation-induced emission (AIE) characteristics for in vivo inflammation imaging and tumor theranostics. This nanoprobe, denoted as CPPO@TN NPs, was constructed by co-encapsulating a tailored AIE photosensitizer (TN) with strong NIR emission and high singlet oxygen (1O2) generation, a H2O2-responsive chemiluminescent substrate (CPPO), and soybean oil (as a retarder) within F-127 micelles. Upon encountering H2O2, the nanoprobe undergoes a persistent chemically initiated electron exchange luminescence (CIEEL) process that activates AIEgens, resulting in intense NIR chemiluminescence and sustained 1O2 production without the need for external irradiation. Leveraging this mechanism, CPPO@TN NPs achieved highly sensitive and specific imaging of drug-induced liver injury and peritonitis in murine models, with exceptional tissue penetration and signal-to-noise ratio. Furthermore, the nanoprobe facilitated effective self-luminescent imaging and photodynamic therapy of tumors, significantly inhibiting tumor growth in a 4T1 tumor-bearing mouse model. This platform provides an external light excitation-free theranostic strategy for H2O2-associated diseases.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3510-0
The activity and stability of single-atom catalysts (SACs) are intimately associated with the structure of supports. Herein, by employing a van der Waals (vdW) heterostructure support, we construct a highly active and durable Pt SAC for hydrogen evolution reaction (HER). The unique support consists of monolayer MoS2 attaching on hierarchical N-doped carbon nanocages (hNCNC), on which Pt presents as individual single atoms on the hNCNC and as island-like single-atom layers on the MoS2. The optimized Pt1-MoS2/hNCNC demonstrates low overpotential (11 mV at 10 mA cm−2) and high mass activity (5.6 A mgPt−1 at −20 mV) in 0.5 M H2SO4 solution, outperforming commercial Pt/C. Impressively, the Pt1-MoS2/hNCNC exhibits improved long-term stability in proton exchange membrane water electrolyzer relative to commercial Pt/C. The excellent HER performance is attributed to the regulated electronic structure, robust interaction of Pt atoms with MoS2/hNCNC and facilitated charge transfer. This study establishes an innovative strategy to develop a highly active and durable Pt SAC using vdW heterostructure supports.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3631-1
Anion exchange membrane water electrolysis (AEMWE) offers cost and dynamic-response advantages over proton exchange membrane systems, yet commercial deployment is constrained by the alkaline stability of anion exchange membranes (AEMs) and the sluggish kinetics of non-precious metal catalysts. This work reports a series of poly(terphenyl-diphenylmethane piperidinium) (QPDPMTP) membranes synthesized with varied diphenylmethane (DPM) content. The alkyl chain of DPM induces pronounced microphase separation and elevates free volume fraction, yielding an OH− conductivity of 152 mS cm−1 at 80 °C for QPDPMTP-10. After 1032 h immersion in 6 M NaOH at 80 °C, the membrane retains 90.7% of its initial conductivity. An AEMWE cell integrating QPDPMTP-10 with a non-precious NiFeCo LDH/NiS/NF anode achieves 3.11 A cm−2 at 2 V in 1 M KOH at 80 °C and sustains 1 A cm−2 for 1800 h under gradient KOH concentration. These results establish a viable pathway for durable, low-cost AEMWE systems.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3551-5
Flexible photonic crystal (PC) materials exhibit exceptional optical properties but suffer structural degradation under repeated mechanical stress, leading to photonic band gap impairment and limited sustainability. This study introduces a self-healing thermoplastic polyurethane (STPU) with an inverse-opal PC structure, inspired by natural structural coloration and self-healing mechanisms. Synergistic dynamic covalent disulfide bonds and hydrogen bonds enable reversible mechanical adjustment, yielding a tensile strength of 26.76 MPa and elongation at break of 2000%. The inverse opal structure facilitates reversible color transitions in response to solvents (water, ethanol) and mechanical strain (0–70%) via lattice spacing modulation. Incorporating an interpenetrating network of polyacrylamide hydrogel and carbon nanotubes enhances strain sensitivity and structural color stability. The material demonstrates broad potential in flexible sensors, adaptive optical devices, bioinspired robotic skins, and dynamic anti-counterfeiting encryption, overcoming traditional PC limitations such as high fragility and single functionality. This strategy advances durable intelligent sensing materials with enhanced environmental adaptability and multifunctional integration.