SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4419-1
Proton exchange membrane fuel cells (PEMFCs) fed with reformate hydrogen suffer severe anode poisoning by trace CO, necessitating high CO electrooxidation potentials that degrade performance and durability. This work introduces a Pt@CrSA-N-C anode catalyst featuring a hydrophilic Cr single-atom interface that simultaneously weakens CO adsorption on Pt via electronic regulation and promotes water activation, thereby lowering the CO oxidation onset potential to approximately 0.13 V vs. RHE. The onset potential was determined by two independent methods: the first potential at which the background-corrected current exceeds 0 mA cm-2 during CO oxidation reaction tests in a three-electrode system, and the potential at which the forward scan current exceeds the N2 background current in CO-stripping voltammetry. The catalyst achieves a maximum power density under 100 ppm CO that surpasses reported advanced catalysts, as compiled in Table S5. Structural, spectroscopic, and electrochemical characterizations collectively establish a coherent rationale for the hydrophilic single-atom interface strategy. This approach addresses the longstanding trade-off between CO tolerance and Pt utilization, offering a viable route for low-potential CO removal in practical PEMFC anodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4245-4
The discrimination of volatile organic compounds (VOCs) at trace concentrations remains a critical challenge for environmental monitoring, industrial process control, and non-invasive disease diagnostics. Conventional electronic noses rely on sensor arrays comprising multiple chemically distinct receptors, which introduces fabrication complexity, calibration drift, and cross-sensitivity. Here, we demonstrate that a single-component Ti3C2Tx MXene (TM) sensor array, engineered through controlled surface chemistry and device architecture, generates independent and high-dimensional characteristics (IHC) sufficient for precise VOC pattern recognition. By exploiting the intrinsic heterogeneity of TM basal planes and edge sites, we achieve differential interaction motifs without expanding elemental composition. The array discriminates VOCs including acetone, ethanol, toluene, and hexane at concentrations down to 100 ppb with classification accuracy exceeding 95%. Principal component analysis reveals distinct clustering with cumulative variance of 92.3% captured by the first three principal components. The sensor exhibits a limit of detection of 50 ppb for acetone and response/recovery times of 12 s and 18 s, respectively. Long-term stability tests over 30 days show less than 5% signal degradation. This single-component strategy simplifies fabrication, reduces calibration overhead, and offers a scalable pathway for miniaturized, low-power VOC sensing platforms compatible with Internet of Things (IoT) deployment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4405-9
Conventional metal-halide X-ray scintillators, including Bi4Ge3O12 (BGO), Cs(Na)I:Tl, and Lu1.8Y0.2SiO5:Ce (LYSO), suffer from hygroscopic decomposition, high-temperature fabrication, and mechanical rigidity, which restrict their deployment in harsh-environment radiography. This study reports a nontoxic zero-dimensional organic–inorganic hybrid copper(I) halide, Cu2I2(C26H36NP)2 (Compound G), synthesized via a room-temperature solution route. The bulky phosphine ligands confer exceptional superhydrophobicity, with the material retaining 91.95% of its initial luminescence after 30 days of water immersion. A flexible scintillator screen fabricated from styrene-ethylene-butene-styrene (SEBS) exhibits a light yield of ~32,500 photons MeV-1, a spatial resolution of 19.14 lp mm-1, and a detection limit of 0.8 μGyair s-1. The screen enables stable X-ray imaging under flexible, high-temperature, and underwater conditions, eliminating vignetting and distortion in nonplanar objects. These metrics demonstrate that the superhydrophobic copper(I) halide scintillator addresses the water-stability bottleneck of commercial scintillators while delivering competitive light output and resolution, offering a viable pathway for medical diagnosis, nondestructive inspection, security checking, and space exploration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4347-9
Overcoming the intrinsic loading ceiling of oxide-supported single-atom catalysts remains a long-standing challenge, because oxide frameworks generally provide limited capacity for accommodating high densities of isolated metal species. Here, we report a hollow TiO2 nanoreactor that effectively addresses the long-standing loading limitation of oxide-supported catalysts by coupling high-capacity ion exchange with structural confinement. The multiscale framework is derived from a sodium titanate hollow flower-sphere assembled from ultrathin nanosheets. It enables broad accessibility of exchange sites and facilitates high Cu uptake prior to oxide formation. Subsequently, during Ar-assisted transformation into oxygen-vacancy-rich TiO2, the incorporated Cu species remain highly dispersed within the framework, while vacancy-mediated metal–support interactions further enhance their stability. As a result, controllable Cu speciation is achieved at ultrahigh loadings of 7.4 wt% as spatially isolated single atoms and 12.4 wt% as single-atom/subnanometer-cluster hybrids. The optimized hybrid catalyst delivers a hydrogen evolution rate of 28.8 mmol g−1 h−1 under simulated sunlight, surpassing conventional low-loading Cu/TiO2 systems under comparable conditions. This strategy is readily extendable to other transition metals (Fe, Co, and Ni), establishing a structural design principle for constructing high-density and speciation-controlled metal sites on oxide supports.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4420-7
Cu2-xSe is a leading p-type thermoelectric material owing to its phonon-liquid electron-crystal (PLEC) behavior, yet the atomic-scale mechanisms governing Cu+ migration remain unresolved. This study employs in situ high-resolution neutron diffraction coupled with maximum entropy method (MEM) analysis to map the temperature-dependent evolution of Cu+ nuclear density in β-Cu2Se and β-Cu1.95Se. At 398–423 K, intra-tetrahedral Cu 8c ↔ 32f <111> hopping emerges, with isosurface values of 0.505 fm Å-3 for β-Cu2Se and 0.484 fm Å-3 for β-Cu1.95Se. Above 448 K, inter-tetrahedral pathways form via Cu 32f ↔ 32f <100> or 32f ↔ 4b ↔ 32f <111> migration, as revealed by line scans along [1̅11̅] up to 723 K. The presence of Cu vacancies (x = 0.05) alters the onset and connectivity of these pathways, directly impacting phonon scattering and electron transport. These findings establish a structural basis for controlling Cu+ mobility, offering a rational route to mitigate Cu precipitation and enhance zT stability beyond 1.5 at 900 K. The work bridges microstructural dynamics and thermoelectric performance, providing critical guidance for defect engineering in superionic thermoelectrics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4309-8
Iridium-doped cobalt oxide nanosheets derived from a ZIF template were evaluated as oxygen evolution reaction (OER) catalysts for proton exchange membrane water electrolysis (PEMWE). Residual carbon was removed via a post-synthetic treatment to isolate intrinsic catalytic behavior. The Ir0.23Co0.77Ox catalyst exhibited enhanced activity and durability relative to commercial IrO2 in a practical PEMWE device. Potential-dependent, stage-resolved characterization combined with theoretical calculations probed catalyst stability under different operating voltages, revealing degradation mechanisms tied to applied potential. Contact angle measurements showed that the Ir0.23Co0.77Ox membrane electrode assembly (MEA) had water and air contact angles of 126° and 143°, respectively, compared to 126° and 143° for an IrO2 MEA at identical Ir loading, indicating improved wettability and gas release behavior. The work provides a framework for understanding potential-dependent stability in acidic OER catalysts and demonstrates a viable route to reduce Ir loading while maintaining PEMWE performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4306-5
Olefin-paraffin separation is a critical and energy-intensive process in the petrochemical industry, with ethylene and propylene purification alone consuming 0.3% of global energy. Current distillation methods are energy-inefficient, and polymer membranes exhibit inadequate separation performance. Metal-organic frameworks (MOFs), particularly ZIF-8, offer precise molecular sieving due to their uniform pore aperture (~3.4 Å), which lies between the kinetic diameters of propylene and propane. Despite excellent lab-scale performance, ZIF-8 membranes face scalability challenges, with effective areas typically below 10 cm², far from the tens of thousands to millions of square meters required industrially. This paper reviews a recent breakthrough by Weihong Xing, Yichang Pan, and colleagues, who developed a micro-space transformation process (MSTP) for scalable fabrication of heterostructured ZIF-8 (HZIF-8) membranes. Using sealed inner lumens of tubular ceramic supports as confined reaction spaces, they achieved single-tube areas of ~200 cm² and total fabricated areas exceeding 4.6 m². The membranes demonstrated stable separation performance over 30 days at 17 bar and 55 °C with a feed flow of 20 Nm³ d⁻¹. This work represents a significant step toward industrial application, addressing critical bottlenecks in membrane area expansion, defect control, and mechanical stability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4302-9
The pre-deposited lead iodide (PbI2) film in two-step inverted perovskite solar cells (PSCs) often exhibits a dense structure, which impedes the diffusion and reaction of organic ammonium salts, leading to unreacted PbI2 residues and compromised device performance. To address this, 2,4-oxazolidinedione (OD) is introduced as a molecule additive into the PbI2 precursor solution. Owing to its stronger coordination with PbI2, OD effectively modulates its crystallization behavior, resulting in a porous structure. This porous structure significantly facilitates the diffusion and infiltration of organic ammonium salts, thereby minimizing PbI2 residue and enhancing the completeness of the perovskite conversion. Furthermore, OD and the constructed porous network jointly retard the crystallization kinetics of perovskite, promoting the formation of perovskite films with improved crystallinity and preferred crystal orientation. Therefore, the optimized PSCs achieve a power conversion efficiency (PCE) of 26.31%, and demonstrate excellent operational stability, retaining 90.24% of initial PCE for 1500 h at 25°C and 90.47% after 1000 h at 65°C. The champion device exhibits a VOC of 1.197 V, a JSC of 26.28 mA cm-2, and an FF of 83.58%, with negligible hysteresis. This study presents a straightforward yet effective approach to advancing the performance and stability of inverted PSCs fabricated via the two-step method.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4323-8
Sulfur-based batteries are promising for next-generation energy storage due to high theoretical capacity, natural abundance, and low cost of sulfur cathodes. However, practical implementation is impeded by sluggish sulfur redox kinetics, dissolution and migration of intermediate polysulfides, and formation of insulating discharge products. Conventional catalyst design focuses on charge distribution, adsorption energetics, and structural confinement, yet these approaches incompletely describe the complex electronic processes governing sulfur conversion. Electron spin, an intrinsic quantum degree of freedom, offers an additional dimension for modulating catalytic behavior via its influence on electronic structure and orbital interactions at catalytic interfaces. In spin-polarized systems, changes in occupation and splitting of transition-metal d orbitals can regulate d-p hybridization with sulfur species, affecting interfacial charge transfer and energetics of sulfur redox reactions. This review summarizes recent progress in elucidating and manipulating electron spin in sulfur-based battery systems. Fundamental principles connecting spin states with electronic structure and catalytic behavior are outlined, followed by experimental approaches for probing spin-related electronic properties using spectroscopic and magnetic characterization techniques. Emerging strategies for spin regulation are highlighted, including heteroatom doping, defect engineering, coordination environment modulation, chirality-induced spin selectivity, and external magnetic-field control. Remaining challenges in identifying spin effects under realistic electrochemical conditions are addressed, along with opportunities for integrating spin-related descriptors into catalyst design. Establishing quantitative relationships between spin polarization, orbital hybridization, and sulfur reaction pathways may provide new perspectives for high-performance sulfur-based batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4350-4
Flexible wearable sensors have transformed motion tracking, soft robotics, and human-machine interfaces by enabling precise movement detection and adaptability to curved surfaces. However, conventional composite sensors often face challenges such as limited sensitivity, detection range, linearity, and durability. In this study, we propose a stretchable auxetic sensing textile with a negative Poisson’s ratio (NPR) structure, incorporating reduced graphene oxide (rGO) and carbon nanotubes (CNT) by micro-crack engineering to enhance its mechanical durability and sensing performance. Integrating macro-scale NPR with micro-scale wrinkles, this innovative design achieves a high sensitivity of 11.2 within a wide detection range (0-100%), a more linear sensing range with an R2 value of 0.998, an ultra-low detection limit of 0.5%, and exceptional durability, outperforming conventional wearable sensors. Additionally, the textile sensor boasts excellent moisture permeability (32.7 g m⁻² h⁻¹) and a remarkable NPR value of -0.25, ensuring comfort and adaptability for various wearable applications. Integrated with deep learning algorithms, the auxetic sensing textile demonstrates 98% accuracy in recognizing soft robotic movements at various bending angles. It is capable of capturing both small-scale physiological signals, such as electrocardiograms, and large-scale movements, offering significant freedom of movement and adaptability to complex surfaces.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4367-4
Single-crystalline Cs3Cu2I5 has attracted considerable interest owing to its excellent scintillation performance and favorable stability. Nevertheless, second phases induced by peritectic reactions during melt growth give rise to deteriorated scintillation properties and promote crystal cracking. In this work, the effects of non-stoichiometric ratios of raw material (n(CsI)=0.57, 0.62, and 0.63) on the crystallization behavior and scintillation properties were systematically investigated. The results show that the crystal quality is optimal at n(CsI)=0.62, featuring high transparency, absence of macroscopic inclusions, and cracking free, with a PLQY of 79.3%. Temperature-dependent photoluminescence verifies the self-trapped exciton emission mechanism with strong exciton-phonon coupling, giving an exciton binding energy of 473.9 meV and a Huang-Rhys factor S of 79.8. The as-grown crystal exhibits an optimized light yield of 24,380 photons/MeV, an energy resolution of 3.8% for 137Cs (662 keV) γ-rays, a dominant decay time of 957 ns, and excellent linear response in the medium-to-high energy region. Precise regulation of the raw material stoichiometry can effectively suppress the formation of second phases, yielding high-quality Cs3Cu2I5 single crystals whose comprehensive performance demonstrates promising application potential in γ-ray detection.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4277-1
Two-dimensional (2D) magnetic materials hold promise for next-generation spintronics, yet most exhibit Curie temperatures (Tc) far below room temperature, limiting practical applications. Here, we report the realization of room-temperature ferromagnetism in CuCrSe2 nanosheets via controlled anion removal achieved by post-synthetic vacuum annealing. Raw CuCrSe2 shows a low Tc of ~120 K, whereas annealed CuCrSe2 (A-CuCrSe2) nanosheets exhibit robust ferromagnetic ordering above 300 K. Structural and compositional analyses, including transmission electron microscopy, Raman spectroscopy, and X-ray absorption spectroscopy, confirm that A-CuCrSe2 retains the original layered crystal structure with an estimated Se vacancy concentration of approximately 10%. Magnetic measurements reveal room-temperature ferromagnetism in exfoliated nanosheets, corroborated by magnetic imaging and electric transport measurements. Anomalous Hall effect (AHE) measurements uncover the coexistence of two ferromagnetic phases within the same sample: one with low Tc (~120 K) and another with high Tc (>300 K), indicating spatially heterogeneous magnetic ordering driven by anion removal distribution. Density functional theory (DFT) calculations elucidate the microscopic mechanism, suggesting that Se vacancies modulate the magnetic exchange interactions, enhancing Tc. This work demonstrates that anion modulation is an effective intrinsic strategy to achieve room-temperature ferromagnetism in 2D materials, potentially advancing spintronic applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4232-1
Polyanionic cathode materials are widely considered as potential cathode materials for sodium-ion batteries due to their strong three-dimensional framework and intrinsic thermal safety. Nevertheless, the limitation of the specific capacity and energy density hindered their application, which can be ascribed to the common reliance of single-electron redox reaction of the transition metal. By realizing the reversible double redox reaction of vanadium-based and manganese-based polyanion cathodes, researchers have successfully opened up a new way to break through the long-term performance limitations. Recent studies disclose that vanadium and manganese-based polyanionic cathodes exhibit the possibility of realizing a reversible double-redox reaction, which opened up new avenues to overcome the capacity dilemma. However, many fundamental issues remain unclear, including insufficient structural stability at high operating voltages, irreversible structural evolution induced by sodium extraction, sluggish electronic and ionic transport kinetics, and Jahn–Teller distortion. Therefore, it is imperative to summarize recent work in order to clarify the pathway for future investigation. In this review, the key challenges associated with the activation of the double-redox reaction are outlined, followed by the realization and regulation of the double-redox reaction in polyanionic cathode materials. A systematic summary of recent studies is performed for both vanadium and manganese-based compounds, which could contribute to the fundamental understanding of the double-redox reaction mechanism. Combined with the modification strategy and future perspective, this review provides insights into the rational design of polyanionic cathodes with a reversible double-redox reaction. It also offers insights into the development of high-energy-density cathode materials for next-generation sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4197-4
Deep-blue organic light-emitting diodes (OLEDs) remain the most challenging primary-color emitters due to stringent exciton energy requirements. We strategically designed two innovative deep-blue emitters, SCZ-4AnCN and STPA-4AnCN, via systematic functionalization of an anthracene core with arylamino-decorated spirofluorene donors and cyano-substituted phenyl acceptors. Comprehensive theoretical and experimental analyses demonstrate that these spirofluorene-anthracene hybrids adopt precisely engineered distorted configurations, effectively suppressing detrimental intermolecular π–π stacking in condensed phases. The sp3-hybridized bridgehead carbons in spirofluorene units play a pivotal role by simultaneously restricting π-conjugation extension and fine-tuning donor–acceptor interactions, thereby stabilizing the lowest excited singlet (S1) state with dominant local excitation (LE) character. This molecular engineering yields exceptional deep-blue emission with remarkable efficiency. Notably, the materials exhibit unique high-lying reverse intersystem crossing (hRISC) behavior, enabling efficient triplet harvesting. Optimized doped devices incorporating SCZ-4AnCN achieve outstanding performance, including a maximum external quantum efficiency (EQE_max) exceeding 10% and CIE coordinates (0.154, 0.052) approaching the BT.2020 blue standard. Nondoped devices maintain impressive performance with an EQE_max of 7.51% and superior operational stability, demonstrating less than 10% efficiency roll-off at 1000 cd m−2. This work validates anthracene-based molecular architectures for deep-blue electroluminescence and establishes a transformative design paradigm for next-generation OLED emitters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3865-1
Seawater electrolysis (SWE) is a reusable and convenient avenue for producing hydrogen, offering a promising solution to the energy crisis and global warming. However, poor electrolytic efficiency and irreversible corrosion caused by high concentrations of chlorine severely hinder the commercialization of SWE. To address these challenges, numerous strategies have been proposed in recent years, involving theoretical innovations, directional catalyst design, and electrolyser modification. This review provides a systematic summary of the chlorine-related challenges and solutions encountered in SWE. The chlorine-related theoretical knowledge and challenges in SWE systems are first emphasized. Subsequently, multiple anodic chloride suppression strategies are introduced from three aspects: directional regulation of oxygen evolution catalysts, optimization of electrolyte compositions, and ingenious upgrades of electrolytic cells. Finally, future challenges and development directions for large-scale application of SWE technology are explored. This review offers an in-depth analysis of the chlorine-related challenges encountered in the industrialization of SWE, aiming to accelerate the advancement of this technology toward practical applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3558-4
The development of advanced titanium alloys capable of operating above 600 °C remains a critical challenge for aerospace propulsion systems, where conventional Ti alloys suffer from insufficient high-temperature strength and microstructural instability. Here, we propose a computationally driven design strategy for titanium-based medium-entropy alloys (MEAs) that integrates thermodynamic phase prediction with mechanistically informed strength modeling, enabling systematic exploration of the Ti-Nb-Al-Cr quaternary system. The optimized Ti70Nb10Al15Cr5 MEA exhibits exceptional performance metrics: 18% room-temperature ductility (as-cast), a yield strength of 520.7 MPa at 650 °C (post-aging), and an ultralow density of 4.76 g/cm3 (45% lighter than Inconel 718). Microstructural characterization reveals a metastable single-phase BCC structure in the as-cast state, which transforms into a BCC/Ti3Al dual-phase system upon aging, with temperature-dependent precipitate morphology and phase stability. The alloy demonstrates superior high-temperature strength retention up to 900 °C (>80 MPa yield strength), outperforming commercial titanium alloys (e.g., Ti-1100, TG6) and bridging the performance gap between conventional Ti alloys and nickel-based superalloys. This work establishes a multi-criteria design paradigm for entropy-engineered alloys, offering a viable pathway to lightweight, high-temperature structural materials for next-generation aerospace applications.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61075-X
The proliferation of electronic devices has intensified electromagnetic radiation pollution, necessitating advanced microwave absorption materials. This study presents the electrospinning fabrication of FeNiCo/carbon nanofiber (FeNiCo/CNF) composites with exceptional microwave absorption properties. The FeNiCo/CNFs achieved a minimum reflection loss (RLmin) of −55.5 dB at 14.24 GHz with an ultrathin matching thickness of only 1.6 mm. Microstructural analysis and electromagnetic parameter testing revealed that the superior absorption stems from the synergistic interaction between the carbon nanofiber network and FeNiCo alloy nanoparticles, which promotes multiple reflections and efficient energy dissipation. The precise control of coercivity and permeability via systematic modulation of magnetic metal composition enabled enhanced impedance matching and optimized magnetic-dielectric synergy. Furthermore, radar cross-section (RCS) simulations confirmed the material's capability to significantly reduce RCS values across a wide angular range, validating its potential for stealth technology applications. This work introduces a cost-effective and sustainable approach for developing ultralight, high-performance microwave absorbers, addressing the limitations of conventional materials such as high density and poor stability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3719-8
The proliferation of 5G communications and smart electronic devices has intensified electromagnetic wave (EMW) pollution, necessitating microwave absorption materials (MAMs) with high efficiency, lightweight, and flexibility. Traditional MAMs suffer from high density and narrow effective absorption bandwidth (EAB). This work presents a lightweight, flexible microwave-absorbing composite fabricated by in-situ polymerization foaming of polyurethane (PU) with multi-walled carbon nanotubes (MWCNTs) and flaky carbonyl iron (FCI). The hierarchical PU composite foam, designated 3*PFC 0.5-1.0-1.5, achieves an EAB of 15.7 GHz, covering 98.1% of the tested 2–18 GHz range, including S, C, X, and Ku bands. This performance stems from synergistic conductive and magnetic losses, along with impedance matching facilitated by the hierarchical porous structure. The composite maintains low density and high compressibility, offering a promising solution for EMW absorption in 5G, military stealth, and smart devices. The in-situ method ensures strong interfacial adhesion between fillers and matrix, enhancing durability compared to impregnation methods. This study demonstrates a scalable approach to fabricate high-performance MAMs with broad bandwidth and mechanical robustness.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3860-0
Drug detection is critical for public health and security, yet reversible and highly sensitive sensing materials remain scarce. This study presents a novel ionogel sensor material, poly(ethylene glycol) diacrylate (PEGDA)/1-butyl-3-methylimidazole tetrafluoroborate, for reproducible detection of N-methylphenylethylamine (MPEA), a structural analogue of methamphetamine. The ionogel is fabricated by immobilizing a flowable ionic liquid within a PEGDA network via UV curing, preserving ionic mobility for efficient conduction. Integrated on a flexible poly(ethylene naphthalate) substrate, the sensor exhibits over 72.6% transmittance in the visible spectrum, enabling concealed attachment. Utilizing non-covalent interactions, the sensor achieves reproducible MPEA detection at sub-ppb levels at room temperature, with a theoretical detection limit of 317 ppt. It demonstrates high selectivity and consistency. Ionic conductivity was confirmed via current-voltage tests and impedance spectroscopy, and the sensing mechanism was clarified. The device maintains reliable performance under bending, indicating suitability for dynamic environments. With Bluetooth integration for wireless data transmission, the sensor shows strong potential for practical, discreet drug monitoring in real-world applications.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61072-4
Sodium-ion capacitors (SICs) typically feature a hybrid design, incorporating a battery-type anode that operates by faradaic redox reactions and an activated carbon cathode that functions through electrical double-layer (EDL) adsorption/desorption. However, the kinetics of faradaic processes are inherently slower than those of EDL processes, leading to a fundamental problem known as kinetic imbalance between the electrodes, which hinders the development of high-performance SICs. To address this, we synthesized composites of bismuth nanoparticles in N-doped carbon (Bi@NC) by a high-temperature sintering method. The resulting Bi@NC anode has a specific capacity of 300 mAh g−1 at 0.5 A g−1, an exceptional rate capability (maintaining performance at currents exceeding 75 A g−1), and outstanding cycling stability over 12,000 cycles. Three-electrode Swagelok cell tests revealed that this high-rate Bi@NC composite effectively decreases the kinetic gap with the activated carbon cathode, as shown by an analysis of their respective potential swing windows (vs. Na/Na+). This enables the fabricated SIC to achieve a maximum energy density of 115 Wh kg−1, a peak power density of 45,535 W kg−1, and a long cycle life exceeding 8,000 cycles.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3795-x
Two-dimensional MXene Ti3C2Tx demonstrates great promise in perovskite solar cells (PSCs). Herein, sulfur-terminated Ti3C2Tx (S-Ti3C2Tx) is developed by modifying Ti3C2Tx via a facile hydrothermal method using thioacetamide. As a perovskite additive, S-Ti3C2Tx outperforms pristine Ti3C2Tx by (1) significantly promoting grain growth, enhancing carrier mobility, and reducing defect density; (2) optimizing energy level alignment to lower interfacial energy barriers and minimize interface non-radiative recombination; (3) stabilizing uncoordinated Pb2+ and [PbI6]4− octahedra via Pb–S bonds while alleviating bulk lattice strain, as this Pb–S interaction exerts a “tape-like” effect. Based on this synergistic mechanism, PSCs with S-Ti3C2Tx achieve a champion efficiency of 25.51%—outperforming control (23.46%) and pristine Ti3C2Tx-based devices (24.54%)—with enhanced stability. This work highlights terminal group engineering as a critical strategy for advancing high-performance PSCs and their potential for emerging photovoltaic technologies.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507027
Ammonia nitrogen (NH3-N) is a common water pollutant that can induce eutrophication and threaten aquatic ecosystems and human health. Accurate monitoring is essential for water safety. This study applied a self-developed gas-permeable membrane-based conductivity sensor (GPMCS) for real-time in-situ monitoring of NH3-N in two water bodies. In the Qunying River (surface river water), GPMCS captured concentration fluctuations linked to pump operations and sewage intrusion, with mean inlet and outlet concentrations of 4.67 and 3.42 mg/L, respectively. In Swan Lake (landscape aquaculture water), concentrations reached up to 11.16 mg/L, with site means of 6.42 and 7.04 mg/L, influenced by aquaculture activities, weather, and location. GPMCS results correlated strongly with national standard methods (r1=0.8132, r2=0.7483), confirming accuracy and reliability. Compared to existing techniques, GPMCS offers high selectivity, strong anti-interference, portability, no sample pretreatment, low cost, and environmental friendliness, making it suitable for long-term in-situ monitoring. This technology provides robust support for sustainable water environment management.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507057
This study presents a novel electrochemical sensor for the rapid detection of trace lead ions (Pb(II)) in water, utilizing a rod-shaped bismuth-based electrode. The electrode was fabricated by modifying a glassy carbon electrode (GCE) with basic bismuth nitrate [Bi6O5(OH)3](NO3)5·3H2O, synthesized via a chemical precipitation method. The sensor was characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), electron probe microanalysis (EPMA), and energy-dispersive X-ray spectroscopy (EDS), confirming the rod-like morphology and composition. Electrochemical detection was performed using differential pulse voltammetry (DPV) in a 0.1 mol·L−1 NaAc-HAc buffer (pH 4.3). The sensor exhibited a linear detection range for Pb(II) from 1 to 90 μg·L−1, with a detection limit of 0.34 μg·L−1 and a sensitivity of 106 μA·(μmol·L−1)−1. The electrode demonstrated excellent anti-interference capability and reproducibility. Recovery tests in real water samples (tap water and campus lake water) yielded high recovery rates, indicating practical applicability. This work provides a simple, cost-effective, and reliable method for monitoring trace Pb(II) in environmental water, particularly relevant for public swimming pools and similar aquatic facilities.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3932-1
Organic room-temperature phosphorescence (RTP) materials have attracted considerable interest due to their unique advantages, such as tunable molecular structures, excellent processability, intrinsic flexibility, and diverse excited-state characteristics. Among these, stimuli-responsive RTP materials, whose luminescence can be modulated by external stimuli (e.g., light, pH, heat, mechanical force or solvent), hold great promise for advanced applications like anti-counterfeiting, information encryption, and sensing. In this review, we systematically summarize recent advances in stimuli-responsive RTP materials, classifying them based on their activation mechanisms. Specifically, we elucidate the fundamental principles governing their stimulus-responsive behaviors and highlight representative examples from various categories. Furthermore, we explore structure-property relationships and design strategies to establish a foundational framework for understanding these materials. This review not only deepens the mechanistic insights into stimuli-responsive RTP systems but also provides strategic guidance for the rational design of next-generation intelligent RTP materials in multidisciplinary fields.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3882-y
Organic semiconductor crystals with well-defined morphologies are highly desirable for high-performance optoelectronic devices, yet precise control over their growth remains a challenge. Here, a novel donor-acceptor (D-A) molecule, TQDPT, has been successfully developed, featuring a rigid π-conjugated acceptor core composed of thiazoloquinoxaline and naphthalene, coupled with phenylphenothiazine donors. This study presents a temperature-mediated crystallization strategy for precisely controlling the morphology and carrier transport properties of TQDPT single crystals. By systematically investigating the growth kinetics across a controlled temperature range (15–35°C), we reveal a distinct transition from needle-like structures to plate-like crystals, with tunable average widths spanning from around 2.8 to 30.1 μm. This morphological evolution is driven by temperature-dependent molecular diffusion and nucleation kinetics. Significantly, the plate-like crystals grown at 25°C exhibit an order-of-magnitude enhancement in mobility compared to needle-like counterparts, while higher temperatures of 35°C yield broader crystals with improved carrier mobility and device stability. This work highlights the critical role of temperature as a pivotal parameter in the dimensional and electronic optimization of organic crystals, offering an attractive approach to optimize functional materials for advanced optoelectronics.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61101-8
Phenolic compounds are typical refractory organic pollutants in coal chemical coking wastewater, posing significant risks to ecosystems and human health. Conventional treatment methods are inefficient, necessitating advanced oxidation processes (AOPs). Here, we report a low-cost Fe/N–C catalyst synthesized from coal-tar pitch, a common by-product of the coal chemical industry, via a self-assembly and pyrolysis strategy using graphitic carbon nitride (g-C3N4) as a template and nitrogen source, with dicyandiamide as an auxiliary nitrogen source and FeCl3·6H2O as the iron precursor. The resulting nitrogen-doped carbon nanosheets possess abundant defects (sp3-C/sp2-C = 0.66) and atomically dispersed iron species. The Fe/N–C catalyst exhibits outstanding catalytic activity for peroxydisulfate (PDS) activation, achieving over 98% phenol degradation within 30 minutes and a 60% total organic carbon (TOC) removal rate. Mechanistic studies, including radical quenching and electron paramagnetic resonance (EPR) experiments, reveal that both radical and non-radical pathways contribute to phenol degradation, with singlet oxygen (1O2) as the primary reactive oxygen species. Electrochemical analyses demonstrate that atomically dispersed Fe sites significantly enhance interfacial electron transfer. Post-reaction characterization indicates the consumption of pyrrolic-N, C=O, and carbon defects as active sites, while graphitic-N and Fe–N structures remain stable, confirming the catalyst's stability. This work provides an economical route to convert coal-tar pitch into high-performance catalytic materials for efficient water treatment, embodying the circular economy concept of waste-to-resource utilization.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61103-1
Flexible pressure sensors that simultaneously achieve high sensitivity, mechanical strength, and long-term stability remain challenging, particularly for biomass-derived carbon aerogels that are intrinsically brittle and prone to structural collapse. Here, we report a bidirectionally frozen carbon aerogel reinforced with tetrapod ZnO whiskers (T-ZnOWs) for high-performance pressure sensing. The aerogel is composed of cellulose nanofibers (CNFs), nitrogen-doped carbon nanosheets (NCs), and T-ZnOWs, which are reorganized into a mechanically stable, parallel lamellar structure via bidirectional freezing. T-ZnOWs act as rigid interlayer pillars, bridging adjacent carbon lamellae to form a 'layer-support' structure that enables efficient directional stress transfer, suppresses interlayer slippage, and promotes cooperative deformation. The nitrogen-doped carbon nanosheets introduce defect-rich conductive paths, enhancing piezoresistive response. Due to modulus mismatch between the supports and carbon layers, applied stress concentrates at layer/support interfaces, generating localized high-stress regions that amplify electrical signal changes. The aerogel is infiltrated with polydimethylsiloxane (PDMS) to form a conformal elastic encapsulating layer, improving durability. The resulting sensor exhibits a high gauge factor of 34.4, an ultrahigh sensitivity of 248.41 kPa−1 over a broad pressure range (0–19 kPa), fast response (24 ms) and recovery (69 ms) times, and stable operation over 5000 loading–unloading cycles. The sensor reliably detects physiological signals and joint motions, demonstrating potential for wearable and intelligent sensing applications. This work provides a strategy to improve the mechanical reliability and sensing performance of biomass-derived carbon aerogels.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61108-0
Adipic acid is a key monomer for nylon-6,6 and nylon-6, yet its industrial production via nitric acid oxidation of KA oil suffers from high energy consumption and N2O emissions. This study reports a green catalytic system for one-pot oxidation of cyclohexane to adipic acid using a Cu/Cu2O@C composite catalyst derived from wood chips. During pyrolysis, wood chips serve as both carbon support precursor and in-situ reducing agent, converting Cu2+ into Cu/Cu2O active species. The abundant defects in biomass carbon form strong coordination interactions with copper, regulating the electronic distribution of active sites and enhancing catalytic performance. Under optimized conditions (100 °C, 12 h), the Cu/[email protected] catalyst achieves a cyclohexane conversion of 19.36% and an adipic acid selectivity of 73.28%. Mechanistic studies reveal that the electronic interaction between the carbon support and copper species strengthens adsorption of cyclohexanone, promoting selective formation of adipic acid. The reaction follows a free radical chain mechanism involving hydroxyl and alkyl radicals. This work provides a viable strategy for developing eco-friendly, low-cost, and high-efficiency catalytic materials for industrial adipic acid synthesis.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508013
The Sanshenggong section of the Yellow River is a critical hydrological monitoring and control point, whose water quality directly affects the ecological safety and sustainable water resource utilization of the middle and lower reaches. This study analyzed water quality monitoring data from 2011 to 2024 using the Mann-Kendall test to identify abrupt change years, combined with single-factor evaluation and a fuzzy comprehensive evaluation method improved by CRITIC-entropy weight combination to systematically assess water quality evolution. The Mann-Kendall test identified 2013 and 2019 as abrupt change points, with non-significant improvement from 2013 to 2015 and significant improvement after 2016. Single-factor evaluation indicated that total phosphorus (TP) was the primary exceeding factor in 2011–2012, and its declining concentration drove the water quality upgrade from Class III to Class II in 2013. The CRITIC-entropy weight combination assigned the highest weight (28.96%) to permanganate index, whose decline was the core driver of water quality improvement. The improved fuzzy evaluation showed that the membership degree of Class III water dropped to zero in 2013, indicating stable improvement, but periodic rebounds in Class II membership suggested potential degradation risks. This study provides scientific evidence for ecological protection and high-quality development of the Yellow River Basin.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60673-1
Temperature-programmed desorption (TPD) is a fundamental technique in surface science and heterogeneous catalysis for characterizing adsorption behavior and extracting key parameters such as adsorption energy. However, the majority of existing TPD data is accessible only in the form of published images, lacking structured and quantitative datasets, which constrains rigorous quantitative analysis and computational modeling. Using carbon monoxide (CO) as a widely adopted probe molecule, we constructed a curated and standardized dataset of CO-TPD spectra encompassing 14 transition-metal single-crystal surfaces, including copper (Cu) and ruthenium (Ru). By systematically extracting numerical data points from published spectra and applying normalization, essential spectral features such as peak shape are fully preserved. The dataset also documents relevant experimental parameters, including heating rates, and was developed using a standardized protocol for data collection and quality control. This resource serves as both a reference library to support the deconvolution of TPD spectra from complex catalysts and an experimental benchmark for calibrating parameters in theoretical models. By providing a reliable and accessible data function, this work advances the microscopic understanding and rational design of catalyst active centers.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025092802
Activated carbon (AC) filters in drinking water treatment plants (DWTPs) experience significant adsorption performance decline over extended operation, yet complete media replacement is a major cost. To evaluate cost-effective strategies, pilot-scale column experiments with five AC replacement ratios (0%, 30%, 50%, 70%, and 100%) were conducted to assess removal of disinfection by-product (DBP) precursors and pesticide-related emerging contaminants. For dissolved organic matter (DOM), all fractions except low molecular weight compounds (LMWC) achieved >85% of the removal obtained with full replacement when 70% new AC was used, with UV254 removal reaching 70%. LMWC, due to small molecular size and low adsorption energy, required higher replacement ratios or full replacement for substantial removal. For DBPs, removal of trihalomethanes (THMs) and haloacetic acids (HAAs) was insensitive to replacement ratio, while haloacetaldehydes (HALs) removal improved markedly with increasing ratio, indicating structural selectivity. For pesticide-related contaminants, all except triazoles achieved >95% removal at 70% replacement; triazoles, due to high water solubility, high polarity, and low octanol-water partition coefficient, achieved only ~60% removal. Overall, replacing 70% of AC restored treatment performance to >80% of that with full replacement, ensuring effluent quality while saving ~30% of new carbon cost. Molecular structure, polarity, and pore size matching are key determinants of removal efficiency; optimizing replacement ratio balances water quality and economic benefits.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605004
To address the decline in operational performance of sewage pipeline networks in rainy cities of southern China caused by structural defects, stormwater-sewage cross-connections, and external water intrusion, a systematic governance framework comprising precise investigation, dynamic regulation, graded rehabilitation, and smart operation and maintenance was established. A zoned priority evaluation model was developed with comprehensive problem severity (P) and governance contribution (B) as core indicators, based on which differentiated governance strategies were formulated. Supported by a digital platform, monitoring, assessment, rectification, and verification data were integrated to develop a digital twin system for the pipeline network, and a correlation-based analysis and closed-loop operation and maintenance mechanism linking rainfall, groundwater level, and network hydraulic load was established. A typical urban area in Jiangxi Province was selected as the case study. After implementation, the mean COD concentration of terminal sewage in the study area increased steadily to above 230 mg/L, the average daily external water volume in the dry season decreased by 27.64%, and the sewage collection rate increased to 76%. The results indicate that the proposed framework can effectively support the quality and efficiency improvement of sewage pipeline networks in rainy cities of southern China, and provide a technical reference for similar cities.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605023
Identifying the characteristics of carbon emissions and driving forces of the railway sector is essential for formulating effective measures to develop a green and low-carbon railway industry. This study systematically evaluated the direct and indirect carbon emissions from 2016 to 2021 generated by the railway sector of China, and analyzed the spatiotemporal dynamic changes of the carbon emissions. On this basis, by adopting the LMDI model, the key factors affecting the carbon emissions of railway sector were discerned. Moreover, the variations in the dominant factors of the carbon emissions over time, and the spatial heterogeneities in the dominant factors of the carbon emissions of the 18 railway bureaus, were analyzed. The results show that: 1) During the periods from 2016 to 2021, the carbon emissions of China's railway sector showed an overall upward trend, increasing from 57.7486 million tons to 64.2084 million tons, by 11.2%. The Shanghai Bureau, Beijing Bureau, Zhengzhou Bureau, Chengdu Bureau and Guangzhou Bureau substantially contributed to the increases of railway carbon emissions. In spatial, the carbon emissions of the 18 railway bureaus were characterized by lower emissions in the west and higher emissions in the east, mainly due to the regional differences in the socio-economic development, industrial structure and population density; 2) During 2016 to 2021, the decline in energy consumption intensity reduced the carbon emissions of the railway sector by 18.8654 million tons, while the changes in carbon emission intensity, economic benefits of per unit passenger and freight turnover, and operating capacity led to an increase of a sum of 25.3252 million tons of carbon emissions. When decomposing the contributions of each factor by sub-periods, it can be found that the impacts of these factors on the carbon emissions changed over time. Only the factor of carbon emission intensity showed a promoting effect in all sub-periods, the other three factors, as energy consumption intensity, economic benefits of per unit passenger and freight turnover, and operating capacity, had a conversion between promoting and inhibiting effects. 3) The dominant factors of carbon emissions across the 18 railway bureaus exhibited spatial heterogeneity. For instance, operating capacity was the main promoting factor for bureaus like Taiyuan, Beijing, Lanzhou, Nanning, Hohhot, Urumqi, and Qinghai-Tibet, while energy consumption intensity was the main inhibiting factor. For Shanghai, Kunming, Wuhan, Chengdu, Xi'an, Zhengzhou, Jinan, Shenyang, Nanchang, and Guangzhou, economic benefits per unit turnover was the main promoting factor, with energy consumption intensity as the main inhibiting factor. For Harbin, energy consumption intensity was the main promoting factor, while economic benefits per unit turnover was the main inhibiting factor. 4) The railway sector can reduce carbon emissions by optimizing transport organization to reduce empty car rates, optimizing energy structure, and retrofitting infrastructure for energy efficiency, while implementing differentiated emission reduction strategies tailored to each bureau's characteristics.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605024
The refined quantification of carbon footprint in engineering construction projects is critical for formulating targeted carbon reduction strategies during the materialization phase. This study integrates material flow analysis (MFA) with the emission factor method to establish a panoramic carbon flow model for engineering projects. Construction activities are categorized into processing and construction, and office and daily operations, clarifying material and carbon flow relationships within the system boundary and with external systems. Empirical analysis was conducted on the Hejiawan Bridge of Section 11 of the Xiyu High-Speed Railway. Results show that the total carbon flow amounts to 27,482,432.11 kg CO2eq, with direct carbon flow (fuel oil, gasoline) accounting for 7.6% and indirect carbon flow (products, transportation, electricity) accounting for 92.4%. From the material flow perspective, the total carbon flow comprises product carbon flow (72.88%), resource and energy carbon flow (25.73%), transportation carbon flow (1.04%), waste carbon flow (0.35%), and service carbon flow (0.01%). In terms of activity scope, construction-related carbon flow accounts for 99.17%, while office and daily operations account for 0.46%. Two indicators, material consumption carbon flow rate and energy consumption carbon flow rate, are proposed for the first time. Comparative analysis of five girder bridges reveals that the Hejiawan Bridge has a material consumption carbon flow rate of 3.91 kg CO2eq/kg, ranking highest among similar bridges, while its energy consumption carbon flow rate is 13.40 kg CO2eq/kg ec, at a medium level. The assessment indicates relatively high material consumption, suggesting potential for carbon reduction through structural and geological optimization.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60635-4
A Cu-based carbon catalyst (H-Cu/C) with octahedral morphology was synthesized by pyrolyzing the metal-organic framework (MOF) precursor HKUST-1 under inert N2 atmosphere. Characterization via XPS, XRD, SEM, and HRTEM revealed that Cu(0) nanoparticles were uniformly dispersed in a carbon matrix, with island-like Cu2O structures serving as active sites. The carbon matrix effectively stabilized the metal nanoparticles, suppressing migration and sintering during reaction. Combined with TEMPO and using molecular oxygen as a green oxidant, the H-Cu/C catalyst exhibited high efficiency in the selective oxidation of aromatic alcohols to corresponding aldehydes under alkali-free conditions. Using benzyl alcohol as a model substrate, an alcohol conversion of 99.2% and a benzaldehyde yield of 94.1% were achieved under mild conditions (100 °C, 0.5 MPa O2, 1 h). The catalytic system demonstrated excellent universality for various mono- and ortho/para-disubstituted aromatic alcohols, affording conversions over 99% and aldehyde yields above 95%. The catalyst could be regenerated via H2 reduction and reused without significant loss of activity. This work provides a new strategy for designing green and efficient non-noble metal catalytic systems for oxidation reactions.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025120801
The interaction between microplastic-derived dissolved organic matter (PSDOM) and iron oxides in soil environments can modulate its photosensitization effects, yet the underlying mechanisms remain elusive. This study investigated the influence of hematite with distinct morphologies—flake-shaped (HNPs) and cubic (HNCs)—on the photosensitization of polystyrene-derived dissolved organic matter (PSDOM). Under 500 W mercury lamp irradiation, both hematite morphologies promoted PSDOM degradation, with HNCs exhibiting superior performance: total organic carbon (TOC) decreased from 18.4 mg·L−1 to 12.3 mg·L−1 within 90 min, compared to 13.3 mg·L−1 for HNPs. Three-dimensional fluorescence spectroscopy indicated that hematite alters the humification process, thereby modifying photosensitization. Electron paramagnetic resonance (EPR) spectroscopy identified the generation of singlet oxygen (1O2), hydroxyl radicals (·OH), and carbon-centered radicals (CH3C(=O)OO·). HNCs significantly enhanced 1O2 production, while HNPs favored ·OH generation; both inhibited CH3C(=O)OO· formation. Quantitative analysis via high-performance liquid chromatography revealed that the steady-state concentration of 1O2 was highest with HNCs, reaching 2.80 times that of the PSDOM control, whereas ·OH concentration peaked with HNPs at 1.98 times the control. Notably, the steady-state concentration of 1O2 was approximately three orders of magnitude higher than that of ·OH. These findings elucidate the morphology-dependent role of hematite in PSDOM photosensitization, providing mechanistic insights into the environmental fate of microplastic-derived organic matter in complex soil systems.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025022501
The pretreatment of trace emerging contaminants in environmental matrices is challenging due to diverse methods and uncertain applicability. This study compared solid-phase extraction (SPE) and liquid-liquid extraction (LLE) for extracting endocrine-disrupting compounds (EDCs), particularly phthalate esters (PAEs), using laboratory-spiked blank samples. LLE achieved satisfactory recoveries for PAEs at spike levels below 4 μg·L−1, enabling detection of five PAEs including diisodecyl phthalate (DIDP), with improved efficiency via repeated extraction. SPE offered lower detection and quantification limits, higher accuracy and sensitivity, and achieved high recoveries for 12 EDCs and 10 antibiotics at spike levels ≥0.2 μg·L−1, with detection limits as low as 0.1–6.4 ng·L−1. The developed SPE coupled with liquid chromatography-Orbitrap mass spectrometry (LC-Orbitrap MS) method was applied to industrial wastewater samples. Across five industrial sectors (coatings, rubber, pharmaceuticals, inks, and materials technology), five antibiotics and ten EDCs were detected, with total concentrations ranging from 0.03–0.56 μg·L−1 and 0.07–1.91 μg·L−1, respectively. Sector-specific profiles emerged: rubber industry effluent was dominated by dibutyl phthalate (DBP) at 1.07 μg·L−1, while pharmaceutical effluent featured sulfamonomethoxine (SMM) at 0.34 μg·L−1. This systematic evaluation demonstrates that SPE-LC-Orbitrap MS is robust for complex matrices, providing a technical foundation for accurate quantification of emerging contaminants in industrial wastewater.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606002
Industrial volatile organic compounds (VOCs) emissions are a major contributor to regional air pollution, and the rubber paste preparation process is a significant source. This study developed an intelligent monitoring system for whole-process VOCs management in a rubber paste preparation workshop, integrating software engineering and Internet of Things (IoT) technologies. The system architecture combines a hybrid database (MySQL relational and InfluxDB time-series), MQTT-based low-power wide-area communication, role-based access control, and containerized microservices. Field deployment at a large rubber enterprise enabled real-time monitoring of adsorption/desorption centrifugal fans and data fusion analysis. Under typical operating conditions, the extraction and ventilation systems achieved volume flow rates of 40,000 m³/h and 30,000 m³/h, respectively, maintaining a continuous micro-negative pressure environment that effectively suppressed fugitive emissions. The purification process, comprising zeolite rotor adsorption and regenerative thermal catalytic oxidation, reduced non-methane hydrocarbon (NMHC) concentrations to below 10 mg/m³, meeting the GB 27632—2011 emission standard. The system's multi-level permission management module precisely allocated operational responsibilities across production, environmental, and management roles, reducing response time to abnormal conditions. An online evaluation model for purification efficiency was constructed based on the actual process. The system demonstrates potential for extension to other high-VOCs industries such as coatings and printing. This research provides theoretical and practical references for applying computer technology to VOCs reduction and whole-process management in typical industries.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606015
This study evaluated the sustainability and tissue-specific mechanisms of corn stover as a solid-phase carbon source for nitrate removal from groundwater. Cyclic heterotrophic denitrification experiments were conducted using leaf, stem pith, stem bark, stem node, husk, and mixed tissues as carbon sources. Denitrification efficiency, sustainability, dissolved organic carbon (DOC) release, carbon utilization efficiency, intermediate accumulation, and environmental parameters were systematically assessed. Kinetic modeling, correlation analysis, and structural equation modeling (SEM) were applied to elucidate regulatory mechanisms. Results demonstrated that mixed tissues and husk achieved the highest denitrification efficiency, with nitrate removal rates consistently above 98% across four repeated cycles. Total nitrogen removal reached 39.30 mg/g for mixed tissues and 39.95 mg/g for husk, while byproduct concentrations (NO2-N and NH4-N) remained below 2 mg/L. DOC release profiles indicated stable carbon release and high carbon utilization efficiency (203.99 mg TN/g organic carbon for mixed tissues; 182.41 mg/g for husk). Correlation and SEM analyses revealed that carbon source type indirectly governed total nitrogen removal by modulating DOC release, which subsequently influenced pH, electrical conductivity, and nitrogen transformation pathways. Significant differences among tissues were observed in denitrification efficiency, carbon utilization, and micro-environmental regulation. Mixed tissues and husk emerged as superior carbon sources due to their combined efficiency and stability. However, husk released odorous compounds during operation, posing sensory challenges for practical application. The findings support the potential of corn stover tissues as cost-effective carbon sources for in-situ groundwater nitrate remediation, though further optimization is required for field-scale implementation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3934-1
Solar energy, a clean and abundant resource, can be stored as latent heat in solid-solid phase change materials (SSPCMs) and subsequently utilized, offering great potential for advancing passive thermal management technologies such as thermal camouflage. Conventional SSPCMs often require active heating for high-temperature conditions, leading to additional energy consumption. Moreover, their permanent crosslinked structures limit reprocessability and increase environmental burden. Herein, we present a lizard-skin-inspired, solar-thermal-responsive, and reprocessable SSPCM (FTSPCM) featuring a dual crosslinked structure composed of dynamic phenol–carbamate bonds and Fe3+@Tannic acid (TA) coordination. Polyethylene glycol (PEG) functions as the phase change segment, while TA introduces both reversible covalent crosslinking and photothermal responsiveness. The FTSPCM exhibits a high latent heat of 102.9 J g−1, excellent shape stability, and maintains its thermal performance after three reprocessing cycles at 120 °C. The Fe3+@TA coordination network enables strong near-infrared absorption and efficient solar-thermal conversion, achieving a surface temperature of 62 °C and a conversion efficiency of 96.85% under 2 Suns irradiation. This dual-function design allows the material to achieve passive thermal camouflage via latent heat release at low temperatures and solar-assisted photothermal heating at high temperatures. This work presents a sustainable strategy for developing reprocessable, solar-responsive SSPCMs, showcasing the distinctive advantages of tannic acid-derived polyphenol chemistry in constructing passive thermal management systems for energy-efficient thermal camouflage and solar-driven thermal energy storage.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511003
Tailings dam leakage can cause secondary sudden water pollution events, imposing severe combined stress of high turbidity and heavy metal contamination on natural water bodies within a short period, threatening aquatic ecological security. Existing studies have systematically revealed the pollution characteristics and biological effects of such events, which are fundamentally distinct from natural high-turbidity water and industrial wastewater leakage. Compared with natural high-turbidity water, tailings leakage inputs finer particles with higher specific surface area, leading to more intense and prolonged turbidity stress. Meanwhile, heavy metals in tailings are more enriched than natural sediments, with higher proportions of active forms and bioavailability, causing significant bioaccumulation and toxic effects, and long-term decline in benthic community species richness. Compared with industrial wastewater leakage, tailings leakage simultaneously releases high concentrations of fine suspended solids and multiple heavy metals, forming a unique 'physical-chemical' combined stress. This synergistic effect amplifies biological toxicity through multiple pathways such as mechanical damage, light limitation, and oxidative stress, resulting in severe and often irreversible ecological damage, such as impaired fish swimming behavior and collapse of benthic community structure. Analyzing the long-term impacts of tailings leakage on aquatic ecosystems from the perspective of combined stress is helpful for providing scientific basis for emergency response and medium-to-long-term ecological risk prevention of related sudden water pollution events.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510056
To support the construction of an ecologically clean small watershed in Harbin, a pilot-scale trial of sediment elutriation was conducted in the Hejia Ditch to evaluate its effectiveness in controlling endogenous pollution and to elucidate the underlying mechanisms. After treatment, sediment organic matter, total nitrogen (TN), and total phosphorus (TP) decreased by 5.11%, 10.19%, and 8.71%, respectively. Water transparency, dissolved oxygen (DO), and oxidation-reduction potential (ORP) increased by 102.46%, 11.07%, and 15.66%, while chemical oxygen demand (COD) and ammonia nitrogen (NH4+-N) removal rates reached 35.67% and 22.65%. The technology effectively removed surface suspended sediment, leaving a stable layer of coarse inorganic particles that formed a clear mud-water interface. Post-treatment, clay content decreased by 8.87%, sand content increased by 12.37%, and median (D50) and 90th percentile (D90) particle sizes increased by 32.39% and 159.97%, respectively. Mechanical disturbance and particle size redistribution enhanced oxygen transfer at the interface, increasing the abundance of facultative anaerobic phyla such as Chloroflexi and Spirochaetes, thereby suppressing the generation of odorous gases (H2S, NH3) and preventing sediment resuspension. Increased microbial diversity and richness improved ecosystem stability and self-purification capacity. These results demonstrate that sediment elutriation is an effective method for controlling endogenous pollution in Hejia Ditch, providing a scientific basis for ecological restoration and long-term management.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511002
To treat large-air-volume, low-concentration volatile organic compounds (VOCs) containing tetrachloroethylene (PCE) generated from rubber-metal bonding, this study systematically investigated the adsorption-desorption behavior and interaction mechanisms of PCE, toluene, and methyl isobutyl ketone (MIBK) on granular activated carbon (GAC). Static adsorption experiments showed that PCE adsorption capacity reached 556.6 mg·g−1, while dynamic multi-component adsorption capacity was 179.6 mg·g−1. Kinetic analysis indicated that PCE adsorption was controlled by both intraparticle diffusion and external surface adsorption, whereas toluene and MIBK were primarily intraparticle diffusion-limited. During high-temperature nitrogen desorption, PCE underwent dechlorination, hydrogenation, and recombination, producing trichloroethylene, 1,2-dichloroethane, 1,2-dichloropropane, and HCl, with HCl accounting for 3.61% of the chlorine molar content in adsorbed PCE. After four adsorption-desorption cycles, the iodine value of GAC dropped below the industry standard of 600 mg·g−1; however, water washing and alkali immersion extended the cycle life to 8 and 9 cycles, respectively. The HCl generation pattern in co-adsorption systems was consistent with single-PCE systems. A regeneration process combining alkali immersion and water washing was proposed and integrated into an engineering strategy. Compared to conventional activated carbon adsorption coupled with RTO incineration, the proposed classification strategy reduced annual costs by 49.5×10⁴ CNY. This work provides a cost-effective and safe solution for Cl-VOCs treatment.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511020
With the increasing number of oil pipelines crossing rivers, the potential risks of oil leakage and surface spreading to river ecosystems and water environments are becoming more severe. Scenario-based simulation of oil spill diffusion is a prerequisite for effective interception point placement and leakage risk prevention. Numerous factors influence oil spill diffusion, including environmental conditions, river hydrology, and accessibility of emergency resources. This study integrates these factors and multiple dynamic processes to design eight typical scenarios for oil spill diffusion simulation, considering emergency resource locations, river hydrological regimes, and leakage modes. A case study is conducted on an oil pipeline crossing a river in northwest China. Results indicate that the diffusion distance and affected area are primarily controlled by water conditions and emergency resource accessibility. In emergency management, the efficiency of maintenance and repair resources during high-water months should be prioritized. Mechanistically, external forces such as hydraulic and wind forces have a greater influence on diffusion distance, surpassing internal forces like gravity, viscosity, and surface tension within a short time. For river crossings near emergency resources, internal force effects should be considered in oil spill diffusion simulations. When emergency resource arrival times are long, the diffusion distance based on Fay's theory is relatively small and can be neglected in engineering practice. This study provides a computational basis and methodological reference for risk assessment and emergency response to potential oil spills from pipelines crossing rivers, enhancing the scientific and effective nature of risk prevention and emergency handling.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60650-0
Aldehydes and ketones are valuable oxygen-containing organic intermediates essential for synthesizing fine chemicals, fuels, and materials. Lignocellulosic biomass, as the most abundant renewable carbon resource with an annual production exceeding 180 billion tons, offers a sustainable route to produce platform carbonyl compounds such as furfural, 5-hydroxymethylfurfural (HMF), and low-molecular-weight aliphatic ketones via pyrolysis. This review systematically summarizes recent progress in catalytic pyrolysis of biomass for aldehyde and ketone production. It first outlines the structural features, types, and biomass-derived origins of typical carbonyl platform molecules. Second, it compares the decomposition pathways and intermediate evolution behaviors of cellulose-rich, hemicellulose-rich, and lignin-rich biomasses under non-catalytic pyrolysis, clarifying the influence of multicomponent synergistic effects on aldehyde and ketone formation. Particular emphasis is placed on the mechanistic roles and dominant reaction pathways of metal salts, metal oxides, and carbon-based catalytic systems in regulating key steps such as dehydration, decarbonylation, C−O/C−C bond cleavage, and skeletal rearrangement. The review identifies major challenges, including unclear catalyst structure-activity relationships, inadequate active site stability, and limited product selectivity. Future perspectives propose rational design of multilevel structured catalysts, integration of in situ characterization with multiscale simulation, and development of green scale-up and process integration strategies. This work aims to provide a systematic theoretical reference for high-value biomass utilization and renewable carbon conversion.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60675-5
Hydrogen as an energy carrier offers a promising route to mitigate environmental issues from fossil fuel use. Efficient and inexpensive electrocatalysts for the oxygen evolution reaction (OER) in alkaline media are critical for advancing alkaline water electrolyzers. Transition metal phosphides (TMPs) are promising (pre-)catalysts for OER. This dataset compiles and compares the electrocatalytic OER activity of nickel- and cobalt-based phosphides. The phosphides were synthesized via solvothermal phosphidization or electrodeposition, and their OER activities were evaluated using linear sweep voltammetry in 1 mol/L KOH. Cyclic voltammetry and electrochemical impedance spectroscopy were also performed. The dataset comprises 312 files totaling 14.5 MB. It provides key electrocatalytic parameters and enables analysis of the influence of metal doping, solvothermal conditions (solvent and precursors), and crystallinity on OER activity. This dataset serves as a benchmark for evaluating Ni and Co phosphide materials for alkaline OER and provides a foundation for designing more active TMP-based electrocatalysts through comparative analysis. The materials may also be applied to other reactions such as hydrogen evolution, alcohol oxidation, and CO2 reduction, relevant to fuel cells, electrolyzers, and metal-air batteries, as well as in lithium/sodium-ion batteries and anticorrosion coatings.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3903-4
Cross-wavelength near-perfect light capture technology is crucial in various fields, including spectroscopy, energy conversion, and electromagnetic control. Nevertheless, the primary challenge in broadband absorption is effectively coordinating the intrinsic response behavior of various electromagnetic waves across the nanometer-centimeter scale when interacting with matter. By adopting a multi-scale structural design strategy, the carbon-zirconium heterointerface is integrated into the macroscopic periodic unit cell (PUC) to develop an ultra-wideband light capture material. The optical coupling effect, strengthened by electronic transitions, molecular motion, and spatial scattering effects, endows ZC-PUC with exceptional light-capture performance ranging from ultraviolet to microwave frequencies. Specifically, the ZC-PUC absorber possesses a near-perfect absorption rate of 95.7% across the ultraviolet-visible-infrared spectrum (190–2500 nm), and an effective absorption coverage of 99.99% in the microwave and terahertz bands (1997.9 GHz). More importantly, the as-prepared material maintains the morphology structure and physical phase even when exposed to an alkaline or acidic environment for 365 days and simultaneously possesses stable light capture properties. The easily scalable approach retains excellent structural stability and ultra-wideband light trapping capability under extreme conditions, offering a versatile platform for the development of next-generation devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3966-0
The development of low platinum-loading catalysts for the economically viable hydrogen evolution reaction (HER) remains challenging. Herein, a precursor dilution strategy is used to fabricate Pt nanoclusters anchored on Ni-embedded porous carbon microspheres. The approach begins with the facile synthesis of Zn/Ni-based coordination polymers (Ni-BTC-Zn) due to the isomorphic substitution of Zn2+ and Ni2+. During pyrolysis, the evaporation of zinc species results in a highly porous carbon structure with well-dispersed nickel nanoparticles. Subsequent solvothermal treatment allows for the uniform deposition of Pt nanoclusters to form the final bimetallic PtNi catalysts (PtNi-BTC-C). Among them, the optimized PtNi-BTC-C10 exhibits exceptional alkaline HER performance, requiring an overpotential of only 41 mV to achieve 10 mA cm−2 and a low Tafel slope of 31.1 mV dec−1. It also demonstrates outstanding durability with a current retention of 90.7% after 70 h, far exceeding Pt/C. Extensive characterization confirms that moderate Zn dilution optimally modulates the Ni particle size and dispersion, leading to maximized active sites and enhanced charge transfer. Combined with DFT calculations, the Pt-Ni-cluster model for PtNi-BTC-C10 possesses an optimized electronic structure with a shifted d-band center, which facilitates water dissociation and optimizes H* desorption with the most favorable energetics (0.262 eV). This work provides a fundamental understanding of precursor dilution engineering and offers a versatile pathway for designing advanced noble-metal-based bimetallic electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3964-5
The escalating demand for personalized thermal-moisture comfort, coupled with the high energy consumption of conventional heating and cooling systems and the imperative for low-carbon energy conservation, has driven the development of shape memory smart fabrics that respond to environmental changes. However, existing shape memory thermal-moisture management fabrics suffer from excessively high response temperatures, inadequate response performance, and suboptimal thermal-moisture management. In this work, a dual-network shape memory polymer (SMP) was synthesized, and its shape memory transition temperature was tuned to align with the human thermal comfort range. The polymer was processed into fibers and subsequently into twisted-coiled artificial muscles to enhance reversible strain. Woven with wool into a plain fabric, the resulting textile exhibits adaptive thermal-moisture management, achieving a warp reversible strain of up to 17.5%. At elevated temperatures, the fabric contracts, exhibiting an air permeability of 1546 mm/s and thermal conductivity of 0.0518 W/(m·K); at lower temperatures, it elongates, with air permeability of 1322 mm/s and thermal conductivity of 0.0426 W/(m·K), thereby realizing 'warm when cool and cool when hot' functionality. Compared with commercial wool fabrics, this smart fabric lowers the skin microenvironment temperature by 1.5 °C and offers an energy savings potential of approximately 222.58 MJ/m² per year in capital cities such as Beijing. This work provides a novel technical pathway and design approach for future personalized comfort and low-carbon, energy-saving textiles.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4079-4
Utilization of ultrahigh-nickel LiNi_xCo_yMn_1-x-yO_2 (NCM) (x > 0.97) in Li-ion batteries can distinctively boost energy density through enhanced discharge capacity. However, capacity and thermal stability deteriorate as Ni content approaches the limit. Here, we propose a facile strategy by introducing high-valence tungsten (W) into ultrahigh-nickel polycrystalline LiNi_0.98Co_0.01Mn_0.01O_2 (PCNCM98). W-doped PCNCM98 (W-PCNCM98) exhibits refined, compactly stacked primary particles, whereas PCNCM98 shows equiaxial, non-uniform larger particles. The refined microstructure enhances mechanical strength: average particle hardness of W-PCNCM98 is 104 MPa, 1.5 times higher than PCNCM98 (68 MPa). This improved mechanical property suppresses lattice volume changes and relieves microcrack formation from H2–H3 phase transition. Consequently, cycling performance in pouch-type full cells is significantly enhanced, with capacity retention of 73% after 2000 cycles at 1 C and 25 °C, 54% higher than PCNCM98. Enhanced structural stability and strong electron affinity of W6+ also improve thermal stability: exothermic peak for W-PCNCM98 is postponed to 203 °C with heat generation of 1287 J g−1, versus 190 °C and 1528 J g−1 for PCNCM98. This high-valent doping strategy stabilizes ultrahigh-nickel NCM cathodes, accelerating large-scale EV applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4012-4
Stimuli-responsive fluorescent hydrogels, owing to their tunable optical properties and unique smart response characteristics, have significant potential in encryption applications and information security. However, most current systems are limited to single-stimulus responsiveness and lack the capability for programmable information erasure or multi-modal dynamic synergy. Hence, we propose a multi-stimuli-responsive phase-change hydrogel incorporating aggregation-induced emission hydrophobic carbon dots (AIE-HCDs) and polyethylene glycol (PEG)-cellulose network, demonstrating dynamic fluorescence chromism under various external triggers. The hydrogel exhibits solvent-exchange-triggered fluorescence color changes from blue to red, enabled by the concentration modulation of AIE-HCDs through the exchange between PEG and water. Additionally, the temperature-induced phase transition of PEG from crystalline to molten state modulates the aggregation and dispersion of AIE-HCDs, thereby enabling dynamic fluorescence color changes. The phase transition further confers excellent shape-memory behavior and adjustable mechanical properties, with the tensile modulus varying from 6.28 MPa in the molten state to 36.23 MPa in the crystalline state, while maintaining high transparency (~88% in the molten state). By utilizing micro-contact printing and the multi-stimulus response, an encryption platform enables information to be hidden, selectively read under sequential stimuli (thermal, UV, and solvent), and completely erased upon demand. This strategy demonstrates significant potential for advancing high-level information encryption and anti-counterfeiting technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4000-1
Formamidine lead-based perovskites (FAPbI3) exhibit significant potential in optoelectronic applications. Nevertheless, they encounter challenges related to δ-phase instability and reliance on toxic solvents. In this study, we present a green solvent-additive synergy strategy that employs γ-valerolactone (GVL) in conjunction with reductive acids like oxalic acid (OA), to stabilize α-FAPbI3 single crystals (SCs). GVL enhances the stability of the precursors through the formation of FA+-GVL hydrogen bonds and high-valence [PbIx]2−x clusters, resulting in ambient-stable α-phase SCs, yielding a marked improvement in stability compared to SCs prepared with the toxic solvent γ-butyrolactone (GBL). Additive modulation demonstrates that H+ and reductive groups play a critical role in regulating crystallization, suppressing the δ-phase by promoting FA+ dissociation and inhibiting MA+ deprotonation. A solvent-involved intermediate, δ-FAPbI3-GVL, has been identified; this intermediate evolves into α-FAPbI3 at a low temperature of 60 °C, thereby reducing the energy barriers associated with the α to δ phase transition. In contrast, non-reductive acids and reductive ionic liquids do not inhibit δ-phase formation, with the latter even promoting the crystallization of pure δ-FAPbI3. By utilizing low-volatility OA as an additive, optimized FA0.9MA0.1PbI3 single crystal thin films exhibit a low defect density of 8.3 × 10^11 cm−3. Subsequently, a photodetector was fabricated. Under zero bias voltage and 780 nm illumination, the device exhibited a responsivity of 14.5 mA/W, a detectivity of 3.75 × 10^10 Jones, and a response speed of 149/65 μs. Moreover, without any encapsulation, the device’s performance diminished by only 17% after 30 days of storage in ambient conditions, indicating remarkable stability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3910-0
Perovskite photovoltaics (PVs) have emerged as leading candidates for next-generation solar technology due to low production costs, high efficiencies, and compatibility with large-area manufacturing. However, commercialization faces bottlenecks: toxic solvents, non-uniform film quality over large areas, and insufficient operational reliability. Wang et al. developed a green-solvent ink and a solvent-confinement edge-protection (SCEP) strategy to address these issues. By increasing the fraction of 2-methyltetrahydrofuran (2-MeTHF) in a gamma-valerolactone (GVL) based solvent system, they weakened perovskite-GVL coordination, accelerated solvent extraction during vacuum-chamber drying, and promoted rapid supersaturation toward the desired alpha-phase while suppressing the non-perovskite delta-phase. This resulted in perovskite films with enlarged grains, reduced voids, and improved crystallinity in ambient air. To mitigate edge effects during slot-die coating, they incorporated a cationic surfactant, trimethyltetradecylammonium chloride (TAC), which self-assembled at the liquid-vapor interface, reducing surface tension and inducing Marangoni flow to equalize evaporation. This SCEP strategy suppressed rapid edge evaporation, leading to uniform film morphology. The best-performing modules achieved a total area of 7200 cm², with J-V curves and stabilized efficiency certifications from NREL and TÜV Rheinland, demonstrating commercial viability. This work provides a unified framework for solvent design and process control, advancing perovskite PV modules toward industrial production.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60651-2
Carbohydrates, derived from abundant biomass resources, hold great promise for conversion into fine platform chemicals and fuels, which is crucial for sustainable development. The processes for carbohydrate conversion are predominantly driven by catalysis, with active components such as Brønsted acids and Lewis acids. This review provides a comprehensive overview of the catalytic conversion of various carbohydrates (monosaccharides, disaccharides, and polysaccharides) into high-value-added compounds. It elaborates on the specific pathways and mechanisms involved in reactions like hydrolysis, isomerization, and dehydration for target molecules such as 5-hydroxymethylfurfural, lactic acid, and furfural. Furthermore, the subsequent derivatization of these platform compounds and their application prospects in energy-related fields, including bio-fuels and batteries, are discussed. Finally, the current challenges in research are summarized, and future directions for the development of low-cost and high-performance catalytic systems are outlined.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60655-X
Defect-induced nonradiative recombination critically restricts the power conversion efficiency (PCE) and stability of perovskite solar cells (PSCs). Lewis base additives show great promise in defect passivation, but current screening methods rely heavily on empirical trial and error and lack clear design principles, making it difficult to efficiently discover high-performance candidate materials. Here, we present a machine learning (ML) framework to intelligently screen Lewis base molecules for defect passivation. We trained six ensemble models on a dataset of 146 experimental data points, with Light Gradient Boosting Machine (LightGBM) yielding the best classification performance (87% accuracy). Shapley Additive Explanations (SHAP) interpretability analysis subsequently identifies the highest occupied molecular orbital (HOMO) energy (−7.5 to −6.3 eV), additive concentration (2.5 to 6.5 mg/mL), and simplified molecular backbones (O atom ≤ 2, C atom < 5) as critical design criteria. The ML prediction was experimentally validated: (S)-pyrrolidine-3-carboxylic acid ((S)-PCA) and 2-methyl-1,3-cyclopentanedione (MCPD) (Class Ⅱ) improved PCE by 2.22% and 2.01%, respectively, while 3-hydroxymethyl-3-methylbutanenitrile (3-HMBN) (Class Ⅰ) showed minimal gain. Density functional theory (DFT) calculations further confirmed the stronger binding affinities and elevated defect formation energies of Class Ⅱ additives. Notably, the champion (S)-PCA device achieved a PCE of 24.05%. This work established an ML-accelerated paradigm for the rational design of defect passivators, bridging data science and photovoltaics.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60676-7
Landfilled municipal solid waste (MSW) in China exceeds 8 billion tons, with high moisture (30–50%) and ash content (>50%), complicating conventional treatment. Slag gasification offers a clean and resource-oriented route, but heavy metal leaching from the resulting slag poses environmental risks. This study investigates the effect of rice husk addition (5–15%) on the vitrification of landfilled-waste slag and the immobilization of heavy metals (Cr, Zn, Cu). Results show that adding 5–10% rice husk lowers the slag flow temperature to a minimum of 1213 °C, attributed to active SiO2 reacting with CaO and Fe2O3 to form low-melting eutectics like anorthite. Leaching concentrations of Cr and Zn decrease from 41.60 and 108.00 mg/L to 5.89 and 7.10 mg/L, respectively, with 10–15% rice husk. The amorphous SiO2 enhances silicate polymerization (Q3, Q4 networks), promoting physical encapsulation and chemical incorporation of heavy metals into stable phases such as Zn2SiO4 and CuFe2O4, increasing the residual fraction and reducing bioavailability. At temperatures >1400 °C, volatilization of Cu and Zn increases, with residual rates dropping to 33–60% and 31–55%, respectively, while Cr remains stable (70–123%). This work elucidates the mechanistic role of rice husk in slag structure modulation and heavy metal immobilization, providing a theoretical basis for the co-treatment of landfilled waste and biomass via a 'treating waste with waste' strategy.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60762-1
The CO2 dry reforming of methane (DRM) is pivotal for CO2 utilization within the dual-carbon framework, offering advantages in carbon reduction and value-added chemical production. However, shaped catalysts suitable for industrial-scale DRM remain limited. This work constructs a monolithic catalyst using honeycomb cordierite as the structural support, systematically investigating the effects of organic and inorganic binders on coating structure and catalytic performance. Comparative studies reveal that the active coating fabricated with inorganic aluminum sol exhibits a continuous uniform morphology and excellent adhesion strength. During high-temperature calcination, elemental diffusion within Al2O3 networks bridges the cordierite surface with active catalyst particles, forming a (Ni-Mg)AlxO4 composite structure. This creates robust metal-support interactions between active sites and the residual alumina matrix. The interconnected mesoporous framework provides superior pore confinement, contributing to strong coating adhesion, enhanced activity, and improved resistance to carbon deposition in the monolithic m-NCM-Al-sol catalyst. In contrast, coatings derived from inorganic silica sol suffer from detachment and activity loss due to heterogeneous surface structures and poor adhesion. Organic binders demonstrate inferior performance in macroscopic coating uniformity, adhesion strength, mesoporous confinement, and localized electronic effects, resulting in the poorest catalytic performance. By optimizing aluminum sol coating parameters—binder content, active component dosage, and coating cycles—a synergistic balance between coating thickness and mass transfer is achieved. The optimized catalyst demonstrates excellent DRM performance, providing insights for constructing high-performance shaped catalysts with cordierite coatings.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025050801
Oil-contaminated water poses severe ecological and public health risks, yet conventional treatment technologies are hindered by complex processing and low selectivity. Metal-organic frameworks (MOFs) and their composites, with tunable pore structures, high surface areas, and controllable wettability, offer promising solutions. This review systematically classifies design strategies and synthesis methods for MOFs and MOF-based composites tailored for oil-water separation. We highlight recent advances, emphasizing structure–function relationships. Key performance metrics from representative studies include water contact angles up to 172.3°, separation efficiencies exceeding 99.9%, and adsorption capacities reaching 168 g·g⁻¹. Challenges such as scalability, stability, and fouling resistance are discussed, along with future directions for practical implementation.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025041505
To combat severe air pollution, China has implemented a series of air pollution control action plans since 2013, effectively alleviating PM2.5 pollution. However, PM2.5 concentrations in most cities within the Fenwei Plain still exceed national standards. This study systematically evaluates PM2.5 concentration changes across two policy phases (2013–2020) using the Community Multiscale Air Quality (CMAQ) model, quantifying contributions of meteorology and emissions, and analyzing sectoral source changes. Results show that annual average PM2.5 concentration declined cumulatively by 19% during 2013–2020. In the first phase (2013–2017), regional PM2.5 decreased by 3% annually, with most improvement in winter; however, due to unfavorable meteorology, concentrations increased in Xi'an and Xianyang. In the second phase (2017–2020), PM2.5 declined by an additional 16%, with more effective control measures, particularly in spring and autumn. Emission reductions dominated in both phases, with stronger effects in the second phase (−8 μg·m−3), significantly outweighing adverse meteorological contributions (+3.5 μg·m−3). Nevertheless, many cities still face challenges from unfavorable meteorology, highlighting the need for future policies to account for meteorological influences. Emissions from industrial, energy, and agricultural sources decreased significantly across both phases. However, during winter heating periods, residential emissions emerged as a source equal in importance to industrial emissions, becoming a key target for future emission controls.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026022402
Graphene oxide–silver nanoparticle (GO-AgNPs) nanocomposites synergistically combine the high specific surface area and biocompatibility of graphene oxide with the potent antibacterial and optical properties of silver nanoparticles. This review systematically examines current synthetic strategies—physical, chemical, and biological—and their influence on nanocomposite morphology, loading efficiency, and stability. The biomedical applications of GO-AgNPs are critically analyzed, focusing on antimicrobial activity, anticancer therapy, drug delivery, and biosensing. Mechanistic insights reveal that antimicrobial action involves membrane disruption, oxidative stress, and damage to biomolecules, while anticancer effects are mediated through reactive oxygen species (ROS) generation. The review also addresses challenges such as AgNP aggregation and stability, which are mitigated by GO support. Future directions emphasize the development of multifunctional nanomedicine platforms, with a need for standardized toxicity assessments and scalable synthesis. This comprehensive overview aims to guide further research and clinical translation of GO-AgNPs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4075-1
Titanium alloys, such as Ti-6Al-4V (TC4), are indispensable in aerospace, biomedical, and advanced manufacturing due to their high specific strength, corrosion resistance, and biocompatibility. However, their inherent strength-ductility trade-off and limited stiffness hinder next-generation lightweight structural applications. Traditional ceramic reinforcements (TiC, TiB2, SiC) improve strength but introduce brittleness and interfacial incompatibility, degrading plasticity and fatigue resistance. Graphene, with theoretical strength ~130 GPa and Young's modulus ~1 TPa, offers a promising two-dimensional reinforcement. This review systematically examines graphene-reinforced titanium matrix composites (TMCs), focusing on the intrinsic relationship between preparation, microstructure, and properties. Key preparation routes include powder metallurgy and additive manufacturing, with challenges in achieving uniform dispersion and controlling interfacial reactions. Recent studies demonstrate that surface modification and process optimization can form an ideal interface structure comprising a nano-TiC layer and residual graphene. Even at low graphene additions, synergistic strengthening mechanisms—load transfer, fine-grain strengthening, and Orowan dislocation bypass—significantly enhance strength, hardness, and wear resistance while preserving ductility. This review consolidates critical theoretical and experimental findings, offering guidance to overcome technological bottlenecks and promote engineering applications of graphene-reinforced TMCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4063-2
Quantum dot light-emitting diodes (QLEDs) are emerging as a leader in next-generation display technology. In principle, the efficiency of QLEDs is highly reliant on the radiative recombination rate of injected electrons and holes in the QD emissive layer. Within a solitary light-emitting cycle, a pre-negative-charged QD bursts into a fleeting sparkle upon encountering a hole, much like a lighted piston within a roaring engine. More pistons bring higher horsepower. The challenge of achieving highly efficient QLED lies in how to increase the number of pre-negatively charged QDs. To address these limitations, we developed a ZnO@ZnMgO core-shell nanoparticle (NP)-based electron transport layer (ETL). This design synergistically combines the high conductivity of ZnO core and the low defect density of the ZnMgO shell. Measured by electron-excited transient absorption, the average electron population (<N_e>) in the emissive layer for ZnO@ZnMgO and ZnMgO-based QLEDs was 0.61 and 0.33 at 4 V, respectively, which greatly increases the carrier recombination efficiency. As a result, green QLEDs achieve a peak EQE of 30.66%, maximum luminance of 1,615,039.85 cd/m2, and a low turn-on voltage of approximately 2 V. The T95 operational lifetime exceeded 29,000 h at 1,000 cd/m2. Currently, all parameters are at the top level within the QLED region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4036-4
Alkaline water electrolysis is a pivotal technology for large-scale green hydrogen production, yet its efficiency is constrained by sluggish hydrogen evolution reaction (HER) kinetics at industrial current densities. Here, we propose a synergistic dual-doping strategy to lower kinetic barriers for both Volmer and Heyrovsky steps. A robust amorphous NiCoV nanosheet electrode was synthesized via scalable one-step electrodeposition. In situ spectroscopic and kinetic characterizations reveal that hydrophilic V species optimize interfacial water by disrupting the hydrogen bond network, ensuring rapid supply of free water at the inner Helmholtz plane. Co dopants modulate electronic structure to facilitate electron transfer and optimize intermediate adsorption energetics. The NiCoV electrode requires an ultralow overpotential of 253 mV at -400 mA cm−2, surpassing most Pt-based catalysts, and maintains stability for over 200 h. Industrial validation in a scaled-up electrolyzer demonstrates a cell voltage of 1.89 V at 400 mA cm−2, achieving energy savings of 0.12 kWh m−3 H2 compared to commercial benchmarks. This translates to annual electricity savings of 1.33 × 10^6 kWh for a medium-scale demonstration project, highlighting immense potential for sustainable industrial applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4035-5
Electrocatalytic CO2 reduction reaction (CO2RR) to formate offers a promising pathway for storing renewable electricity in chemical fuels and enabling carbon recycling. The development of efficient and stable catalysts for this specific pathway, however, remains a central challenge. Heteroatom doping can significantly tune the interaction between active sites and key intermediates, boosting catalytic performance. Conventional doping in Bi-based catalysts often relies on uncontrollable in-situ electrochemical processes, leading to ineffective bulk incorporation. Here, we present a simple pre-doping strategy that enables precise doping at surface active sites, thereby enhancing electrochemical performance. The resulting catalyst achieves >95% Faradaic efficiency for formate across 100–500 mA cm−2 in a flow cell and maintains >95% efficiency for over 70 h at 100 mA cm−2 in a membrane electrode assembly, outperforming pure Bi and Bi2S3. A solar-driven system further demonstrates a 4.4% solar-to-formate conversion efficiency. Mechanistic studies reveal that sulfur doping increases electron density, stabilizes the key *OCHO intermediate, and suppresses hydrogen evolution. These findings provide valuable insights into the precise pre-doping modulation of surface active sites for designing highly efficient and stable CO2RR catalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4004-3
The development of efficient and stable oxygen evolution reaction (OER) electrocatalysts is critical for clean energy technologies, yet conventional cobalt-based spinel catalysts often suffer from insufficient activity and structural instability under operating conditions. To address these challenges, this study proposes and constructs a cation-ordered spinel-like catalyst (HVI Metal-CoMoO4/NF). The unique crystalline framework induces significant Jahn-Teller distortion and pre-stabilizes a Co2+/Co3+ mixed-valence state at the cobalt active centers via asymmetric Co–O–Mo bridges, effectively optimizing bulk charge transport. Electrochemical tests demonstrate that its performance significantly surpasses that of benchmark materials, requiring only an overpotential of 307 mV to drive a current density of 100 mA cm−2 in 1.0 M KOH, with a Tafel slope of 63.13 mV dec−1, maintaining stable operation for over 320 h at high current density. Crucially, our structural and in situ characterization results clearly reveal a stable and well-crystallized reconstruction behavior from the surface into the bulk of the spinel-like pre-catalyst during the OER. This work fundamentally addresses the challenges of disordered reconstruction and unstable active phases in traditional spinel catalysts, providing a paradigm for regulating the dynamic evolution of electrocatalysts through precise structural design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4116-0
The design of solid electrolyte interphases (SEIs) for poly(vinylidene fluoride)-based solid-state batteries has largely focused on solvent-affinity of Li+ to generate robust but ionically sluggish LiF-rich layers, inherently compromising transport kinetics. Here, we establish a paradigm based on quantifiable physicochemical descriptors (ionic potential and donor number) to guide the design of amphitropic ion pairs (AIPs). These AIPs are engineered to simultaneously tailor both the solvent-affinity and anion-affinity of Li+: a solvent-philic cation with high ionic potential (Al3+) first sequesters reactive solvents, clearing the path for a high-donor-number, lithium-philic anion (NO3−) to remodel solvation. This rationally guided, sequential mechanism enables the in situ synthesis of a LiF/Li3N heterostructured SEI, where dendrite-suppressing LiF domains are seamlessly integrated with ultra-fast Li3N ion channels. This design heterogeneity effectively enhances stability and kinetics, yielding a robust and highly conductive interface. Consequently, Li|Li cells achieve >2000 h of stable cycling, and Li|LiNi0.8Co0.1Mn0.1O2 full cells surpass 600 cycles.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3968-3
The commercialization of perovskite solar cells (PSCs) is hindered by stability issues primarily stemming from interfacial defects. This study employed a machine learning (ML) screening approach and constructed a learnable weighted ensemble model (LWEM) to enhance prediction robustness for identifying effective interface passivation materials. The ML model predicted that an imidazolium salt-based interface modifier, 1-benzyl-3-methylimidazolium tetrafluoroborate (BMT), is suitable for planar n-i-p PSCs. Subsequent experimental results demonstrated that BMT provides synergistic passivation via an 'ion-coordination dual-lock' mechanism that significantly suppresses non-radiative recombination, facilitates hole extraction, and improves the quality of the perovskite film. The BMT-modified devices achieve a significant increase in power conversion efficiency (PCE) from 22.45% to 24.89% under AM 1.5G illumination, and attain a high PCE of 41.31% under 1000 lux light emitting diode (LED) indoor lighting. Additionally, the modified devices exhibit outstanding stability under long-term storage and maximum power point tracking conditions. This work provides a strategy for developing high-performance and highly stable PSCs for both indoor and outdoor applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3978-0
All-polymer solar cells (all-PSCs) are promising for flexible and wearable electronics due to their excellent stability and mechanical stretchability. However, achieving high performance remains challenging due to difficulties in controlling the morphology of polymer blend films. In this study, a novel polymer donor, PBDTF-DTP, incorporating a weak electron-withdrawing yet large-dipole-moment dithienylphthalimide (DTP-2T) unit, was rationally designed and synthesized for ternary all-PSCs. Introducing PBDTF-DTP as a guest donor enables complementary light absorption and deepens the highest occupied molecular orbital level, simultaneously improving short-circuit current density (J_SC) and open-circuit voltage (V_OC). The large dipole moment of DTP-2T increases the dielectric constant, suppressing non-radiative energy loss and further boosting V_OC. Notably, PBDTF-DTP exhibits a relatively higher molecular electrostatic potential than the host donor, effectively tuning compatibility with both polymer donor and acceptor, regulating blend morphology, and promoting formation of a nanoscale fibrillar network. This optimized morphology facilitates efficient charge generation and transport while suppressing charge recombination. Consequently, ternary all-PSCs based on PM6:PBDTF-DTP:PYIT achieve a synergistic enhancement in J_SC, V_OC, and fill factor, yielding a remarkable power conversion efficiency of 18.01%, significantly higher than that of binary PM6:PYIT devices (15.51%). This study demonstrates that combining electrostatic potential optimization with a ternary strategy provides an effective approach to regulate morphology and achieve high-efficiency all-PSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4059-3
Deuterium (D2) is indispensable for isotope tracing, neutron scattering, and fusion reactions, yet its separation from hydrogen (H2) remains challenging due to their nearly identical physicochemical properties. Adsorptive separation exploiting the kinetic quantum sieving (KQS) effect at cryogenic temperatures offers a promising route, but demands precise pore engineering. Here, we report a biomass-derived carbon molecular sieve that permits rapid D2 transport while imposing a significant diffusion barrier for H2, enabling effective separation from D2/H2 mixtures. The molecular sieving micropores are generated by transforming cellulose components into slit-type carbon micropores, with lignin acting as a pore-size modifier. At 77 K, the diffusion rate of D2 is 1.8 times that of H2, leading to a D2 concentration in the recovered gas approximately 10% higher than that achieved with conventional microporous carbons. Aspen adsorption simulations demonstrate that D2 can be enriched to 90.1% from a 1.0% D2/H2 mixture within 12 successive cycles following a two-bed cryogenic pressure swing adsorption process. These findings advance the development of effective adsorbents for kinetic D2/H2 separation, offering a sustainable, low-cost route to deuterium enrichment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4031-6
Organic fluorophores operating in the second near-infrared (NIR-II, 1000–1700 nm) window are highly attractive for cancer phototheranostics. Yet, the advancement of aza-BODIPY-based NIR-II dyes remains challenging due to their limited spectral tunability and diminished fluorescence quantum yields (FLQY) under physiological conditions. Herein, we propose a rational donor-acceptor (D-A) molecular engineering strategy to construct an aza-BODIPY fluorophore, TPACN, featuring intramolecular charge transfer (ICT)-enhanced NIR-II emission and balanced photothermal performance. By introducing electron-rich triphenylamine (TPA) donors and peripheral cyano (–CN) acceptors, the optimized D-A coupling significantly strengthened the ICT effect, leading to broadened NIR absorption, a markedly red-shifted fluorescence peak at 1086 nm, and an exceptional fluorescence quantum yield of 1.55% in dichloromethane (DCM). When encapsulated in F127, TPACN nanoparticles (TPACN NPs) maintained a high aqueous FLQY of 0.20%, accompanied by a notable photothermal conversion efficiency (PCE) of 39% under 808 nm irradiation. The sterically twisted TPA units effectively alleviated aggregation-caused quenching (ACQ) and fine-tuned the excited-state energy dissipation pathways, realizing a synergistic balance between radiative (fluorescence) and non-radiative (heat) relaxation. Benefiting from these optimized photophysical properties, TPACN NPs achieved high-resolution NIR-I photoacoustic and NIR-II fluorescence dual-modal imaging, enabling accurate tumor visualization and efficient photothermal ablation in vivo. This work introduces a general design paradigm that exploits ICT modulation and steric engineering to overcome the intrinsic fluorescence bottleneck of aza-BODIPY systems, offering new molecular insights for the advancement of high-performance NIR-II dyes for precision phototheranostics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4274-x
The escalating power density of electronic devices necessitates effective visible-light shielding in advanced packaging to ensure circuit security and long-term reliability. Photosensitive polyimides (PSPI) serve dual roles as photodefinable dielectrics and structural layers, but intrinsically black PSPI (B-PSPI) suffer from competitive ultraviolet (UV) absorption between chromophores and photosensitive moieties, limiting co-optimization of deep visible-light blocking and lithographic resolution. Here, we report a main-/side-chain spatial decoupling strategy to synthesize a novel B-PSPI. By polymerizing pyromellitic dianhydride with a main-chain coloring monomer (4,4'-diaminodiphenylamine) and a side-chain photosensitive monomer (1,4-dihydropyridine-functionalized diamine), the monomer stoichiometric ratio is precisely engineered. This design spatially isolates functional groups and enhances charge transfer, yielding exceptional visible-light shielding (CIE L* index of 21.39, cut-off wavelength ≈ 555 nm) with good lithographic sensitivity. UV exposure triggers in situ generation of coordination sites from photosensitive groups, anchoring active metal species for electroless copper plating. This enables direct additive fabrication of fine copper lines (40/80 μm line width/spacing) with robust Cu/B-PSPI interfacial adhesion of 16.6 MPa. This work provides a robust molecular design paradigm for B-PSPI, integrating superior optical shielding and surface metallization for high-density interconnect applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4181-6
Green hydrogen production via electrocatalytic water splitting is pivotal for sustainable energy, yet the high cost and scarcity of platinum (Pt) catalysts impede large-scale adoption. Ruthenium (Ru)-based materials emerge as promising alternatives, but their performance requires enhancement. Two-dimensional transition metal dichalcogenides (TMDs), particularly ReS2, offer intrinsic 1T' phase with good conductivity and stability, yet suffer from inert surfaces limiting water adsorption. Here, we report a heterostructure comprising Ru nanoclusters anchored on ReS2 nanosheets (Ru/ReS2) to modulate electronic structure via d-p coupling. This design enhances water dissociation kinetics and optimizes hydrogen adsorption free energy (ΔG_H*). The Ru/ReS2 catalyst exhibits superior hydrogen evolution reaction (HER) activity in acidic media, achieving an overpotential of 47 mV at 10 mA cm−2 and a Tafel slope of 38 mV dec−1, outperforming commercial Pt/C (overpotential 54 mV, Tafel slope 45 mV dec−1). Notably, it demonstrates exceptional stability, with negligible degradation after 10,000 cyclic voltammetry cycles, contrasting with Pt/C's 54 mV overpotential increase. Density functional theory calculations reveal that d-p coupling between Ru and ReS2 optimizes the electronic structure, facilitating water adsorption and dissociation. This work provides a rational strategy for designing efficient, durable, and cost-effective HER electrocatalysts for green hydrogen production.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3480-1
Electrochemical nitrate reduction to ammonia (NRA) offers a sustainable route for wastewater denitrification and decentralized ammonia synthesis, but its practical deployment is constrained by sluggish reaction kinetics and the competing hydrogen evolution reaction (HER). Monometallic Cu electrocatalysts, despite favorable nitrate adsorption and tunable electronic structure, exhibit weak H* adsorption, limiting the hydrogen radical-mediated pathway that suppresses HER at low overpotentials. Here, highly dispersed Cu/WO3 heterojunctions supported on carbon fiber were synthesized via carbothermal shock reduction, which reaches ultra-high temperatures within seconds and prevents active-site accumulation. The optimal Cu/WO3 heterojunction achieves an ammonia yield rate of 158.66 μmol h−1 cm−2 and a Faradaic efficiency of 98.27%. Electron paramagnetic resonance and density functional theory calculations reveal a synergistic mechanism: Cu sites preferentially adsorb NO3−, while adjacent WO3 sites accelerate water dissociation to generate hydrogen radicals (H*), which drive the continuous hydrogenation of nitrate to ammonia. This spatial separation of functions promotes the H*-mediated pathway and suppresses HER. The work establishes a heterojunction design strategy for non-precious-metal NRA electrocatalysts, enabling high-rate, high-selectivity ammonia production under mild conditions.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3551-5
Flexible photonic crystal (PC) materials exhibit exceptional optical properties but suffer structural degradation under repeated mechanical stress, leading to photonic band gap impairment and limited sustainability. This study introduces a self-healing thermoplastic polyurethane (STPU) with an inverse-opal PC structure, inspired by natural structural coloration and self-healing mechanisms. Synergistic dynamic covalent disulfide bonds and hydrogen bonds enable reversible mechanical adjustment, yielding a tensile strength of 26.76 MPa and elongation at break of 2000%. The inverse opal structure facilitates reversible color transitions in response to solvents (water, ethanol) and mechanical strain (0–70%) via lattice spacing modulation. Incorporating an interpenetrating network of polyacrylamide hydrogel and carbon nanotubes enhances strain sensitivity and structural color stability. The material demonstrates broad potential in flexible sensors, adaptive optical devices, bioinspired robotic skins, and dynamic anti-counterfeiting encryption, overcoming traditional PC limitations such as high fragility and single functionality. This strategy advances durable intelligent sensing materials with enhanced environmental adaptability and multifunctional integration.