SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4343-7
Piezoelectric materials interconvert mechanical and electrical energy, but piezoceramics are brittle while PVDF-based ferroelectric polymers exhibit low piezoelectric coefficients (d33 ≈ -30 pC N-1). Chemical modification via morphotropic phase boundary (MPB) engineering has raised d33 in P(VDF-TrFE) to -63.5 pC N-1, and to -69 pC N-1 with stretching, but intrinsic piezoelectricity in relaxor terpolymers remains limited. Here, relaxor ferroelectric P(VDF-TrFE-CFE) with varying C=C double bond (DB) content is synthesized via dehydrochlorination. Structural and electrical characterization reveals that increasing DB content stabilizes long-range ferroelectric order while suppressing short-range relaxor characteristics, forming a trans/helix phase boundary. At a critical DB content of 2.0 mol%, a markedly enhanced intrinsic d33 of -129.0 pC N-1 is achieved, outperforming previous MPB approaches. This finding addresses the fundamental bottleneck of low piezoelectric response in flexible ferroelectric polymers and provides a viable route for high-performance wearable electromechanical devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4432-9
Sodium vanadium phosphate (Na3V2(PO4)3, NVP) with NASICON structure is a promising cathode for sodium-ion batteries but suffers from low electronic conductivity and a high energy barrier for the V4+/V5+ redox couple, limiting practical energy density. A medium-entropy tuning strategy yields the multi-element substituted Na3.2V1.5Cr0.1Fe0.1Mn0.1Ni0.1Ti0.1(PO4)3 (ME-NVP). Entropy modulation tailors the microscopic electronic structure, enabling reversible V4+/V5+ redox at 4.0 V. Analyses reveal a synergistic diffusion mechanism that accelerates Na+ transport and enhances multiple-electron redox kinetics. Ex-situ X-ray diffraction confirms highly reversible structural evolution during cycling. The ME-NVP cathode delivers 116.8 mAh g-1 at 0.1C and retains 83.9% of initial capacity after 1000 cycles at 20C, with excellent performance from -12 to 50 °C. This work demonstrates that configurational entropy regulation unlocks high-energy polyanion cathodes for advanced sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4476-1
Self-sustained oscillation in soft actuators enables autonomous, untethered robotic locomotion, yet existing light-driven systems suffer from low oscillation frequencies, rapid photothermal degradation, and reliance on external controllers. This work presents a bat-inspired soft robot that converts continuous near-infrared (NIR) irradiation into sustained rotational motion via a coiled MXene-based liquid crystal elastomer (LCE) actuator. The actuator integrates Ti3C2Tx MXene nanosheets as photothermal converters within an LCE matrix, achieving a photothermal conversion efficiency of 78.3% and a steady-state temperature of 142 °C under 1.5 W cm−2 NIR (808 nm). The coil geometry induces a self-shadowing effect that generates periodic light exposure, producing autonomous oscillation at 2.7 Hz with an amplitude of 45°. The robot demonstrates a rotational speed of 120 rpm and a specific power density of 3.2 W kg−1, outperforming previously reported light-driven oscillators by a factor of 2.5. Under continuous operation for 10,000 cycles, the actuator retains 92% of its initial oscillation amplitude, with a degradation rate of 0.008% per cycle. The bat-inspired wing morphology enables directional rotation and obstacle avoidance in confined spaces. This platform eliminates the need for external modulation, offering a scalable route to autonomous soft robotics for inspection, environmental monitoring, and micro-manipulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4494-9
Superionic conductors exhibit high cation mobility arising from weak binding and continuous transport pathways, atomistically characterized by extensive structural disorder and partial occupancy akin to amorphization. This disorder, whether confined to a cation sublattice or extended to full amorphization, strongly impedes lattice thermal transport, rendering these materials intrinsically ideal thermal insulators. This work investigates Ag26I18W4O16, a superionic conductor tunable from fully amorphous to single-crystalline states, as a model system to probe the impact of disorder and amorphization on thermal transport. Extensive Ag+ disorder, in both crystalline and amorphous phases, reduces thermal conductivity to approximately the theoretical lower bound of 0.16 W/m-K with virtually no temperature dependence, while concurrently achieving the lowest mean sound velocity ever recorded for a dense solid. Pair distribution function (PDF) analysis of synchrotron X-ray total scattering data indicates that short-range disorder (< 5 Å), rather than long-range periodicity, governs thermal insulation performance in both phases. These findings suggest a design strategy reconciling structural stability with glass-like thermal insulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4311-y
Chronic infections caused by biofilms of drug-resistant bacteria pose a significant challenge in clinical treatment. Traditional NIR-I photothermal therapy has limitations, including restricted tissue penetration and potential damage to normal tissues due to high temperatures. While NIR-II light offers deeper penetration, there remains a scarcity of materials capable of simultaneously responding to both NIR-I and NIR-II wavelengths and integrating multiple sterilization mechanisms under mild conditions. In this study, a Fe-based high-entropy spinel oxide (HEOs) was designed and synthesized. Benefiting from lattice distortion induced by the high-entropy effect and the hybridization of multiple metal d-orbitals, the material achieves cooperative optimization of its electronic band structure. Consequently, it exhibits efficient broad-spectrum photothermal properties across both NIR-I and NIR-II regions alongside excellent peroxidase-like (POD) activity. Under dual-wavelength laser irradiation, the material enables mild yet efficient photothermal conversion (<50 °C) while simultaneously catalyzing hydrogen peroxide (H2O2) to generate abundant hydroxyl radicals (·OH), thereby constructing a synergistic antibacterial system combining dual-window photothermal therapy and enzymatic catalysis. In vitro experiments confirmed that the HEOs possesses potent bactericidal and biofilm eradication capabilities against both Gram-positive and Gram-negative bacteria. In a mouse model of drug-resistant bacterial wound infection, the material, assisted by either NIR-I or NIR-II laser irradiation, effectively cleared the infection, reduced inflammation, and promoted collagen deposition and angiogenesis, thereby significantly accelerating wound healing. This work not only provides a novel strategy for developing dual-window-responsive antibacterial materials for deep-tissue infections but also deepens the understanding of the structure-activity relationship in high-entropy materials at the electronic structure level.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4177-3
Chirality profoundly influences tumor therapy by regulating key physiological processes, yet the link between chirality and therapeutic properties of atomically precise metal nanoclusters (NCs) remains poorly understood. Atomically precise Au25 NCs protected by chiral cysteine ligands (L-Au25(cys)18, D-Au25(cys)18, and Rac-Au25(cys)18) were constructed and systematically investigated to elucidate the association between chirality and tumor therapeutic performance. Although no significant difference in enzyme-like activity was observed among the three NCs, Rac-Au25(cys)18 exhibited enhanced reactive oxygen species generation under 808 nm laser irradiation, achieving superior phototherapeutic effects in both in vitro and in vivo tumor models. The chiral Au25 NCs induced distinct cell death pathways: L-Au25(cys)18 primarily triggered ferroptosis, D-Au25(cys)18 induced both ferroptosis and apoptosis, and all three NCs activated disulfidptosis. In vivo, tumor inhibition rates for L-Au25, D-Au25, and Rac-Au25 groups were 46.7%, 42.5%, and 68.3%, respectively, with no significant body weight fluctuations and minimal hepatorenal toxicity. Hematological and histopathological analyses confirmed favorable systemic biocompatibility. This work clarifies the correlation between chiral structures and tumor therapeutic performance of gold NCs, providing experimental insights and theoretical support for the design of novel chiral nanomaterials and optimization of precise tumor phototherapeutic strategies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4275-3
Electrochemical in-situ production of active chlorine (AC) via chlorine evolution reaction (CER) can alleviate hull corrosion and residual chlorine overage, which is a highly reliable disinfectant for sewage and ballast water. Nonetheless, the primarily competitive oxygen evolution reaction and gradual anode passivation hinder its practical application. Herein, we employed the in-situ hydrothermal strategy to synthesize Ru/TiO2-x to realize high activity and selectivity of CER. The robust interaction of Ru sites and TiO2-x achieved via a one-step hydrothermal synthesis strategy, the structural and valence state characterizations confirm that Ti3+ stabilizes Ru solely in the metallic state (Ru0) via structural confinement effects, effectively inhibiting catalyst oxidation. As a result, the Ru/TiO2-x requires only an overpotential of 33 mV to reach 10 mA cm−2, and possess strong catalytic durability, sustaining continuous operation for 100 h with negligible current decay. Further integration with a triboelectric nanogenerators successfully realizes the generation of AC, which demonstrates a >99.9% inactivation efficiency against Escherichia coli in simulated seawater environments, while also effectively degrading ammonia nitrogen and urea contaminants in domestic wastewater.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4250-0
Shape memory polymer (SMP)-based transfer printing offers a promising route for heterogeneous integration of flexible electronics, yet non-contact release reliability remains a critical bottleneck. This study systematically investigates the influence of pickup heating modes—localized versus global—on the release yield and energy-delivery mechanisms through combined experiments and finite element simulations. The localized heating mode concentrates strain energy at the interface, enabling controlled chip ejection with high yield, whereas global heating dissipates energy, leading to release failure. Quantitative analysis reveals that localized heating achieves a release yield of 100% under optimized conditions, compared to near-zero for global heating. The ejection velocity under localized heating is higher, which may induce chip bouncing on the receiver substrate, affecting transfer accuracy; however, this can be mitigated by adjusting release gap and laser parameters. The findings establish a theoretical framework for energy pathway design, providing guidelines for achieving high-yield, accurate non-contact release in laser-induced transfer printing. This work advances the practical application of SMP-based transfer printing for micro-LED displays and flexible electronics, addressing a key manufacturing bottleneck.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4277-1
Two-dimensional (2D) magnetic materials hold promise for next-generation spintronics, yet most exhibit Curie temperatures (Tc) far below room temperature, limiting practical applications. Here, we report the realization of room-temperature ferromagnetism in CuCrSe2 nanosheets via controlled anion removal achieved by post-synthetic vacuum annealing. Raw CuCrSe2 shows a low Tc of ~120 K, whereas annealed CuCrSe2 (A-CuCrSe2) nanosheets exhibit robust ferromagnetic ordering above 300 K. Structural and compositional analyses, including transmission electron microscopy, Raman spectroscopy, and X-ray absorption spectroscopy, confirm that A-CuCrSe2 retains the original layered crystal structure with an estimated Se vacancy concentration of approximately 10%. Magnetic measurements reveal room-temperature ferromagnetism in exfoliated nanosheets, corroborated by magnetic imaging and electric transport measurements. Anomalous Hall effect (AHE) measurements uncover the coexistence of two ferromagnetic phases within the same sample: one with low Tc (~120 K) and another with high Tc (>300 K), indicating spatially heterogeneous magnetic ordering driven by anion removal distribution. Density functional theory (DFT) calculations elucidate the microscopic mechanism, suggesting that Se vacancies modulate the magnetic exchange interactions, enhancing Tc. This work demonstrates that anion modulation is an effective intrinsic strategy to achieve room-temperature ferromagnetism in 2D materials, potentially advancing spintronic applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4234-3
The pursuit of high-energy-density sodium-ion batteries (SIBs) necessitates the development of stable high-capacity anodes. While amorphous carbon is a promising anode candidate for SIBs, its practical application is hindered by limited capacity. Herein, we design a composite anode by chemically confining a high-content (~25 wt%) short-chain sulfur into hierarchical porous hard carbon microspheres (SHHC) derived from microbe yeast. The SHHC anode exhibits a high reversible capacity of ~807 mAh g−1 at 0.03 A g−1 (~3 times that of conventional amorphous carbon) along with superior rate capability, and extraordinary long-term cyclability (almost 100% capacity retention after 2000 cycles at 1.0 A g−1). The high-content sulfur species contribute to superb redox reactivity for high-capacity sodium storage via a surface-dominated storage mechanism. The carbon matrix features an enlarged interlayer distance, which facilitates Na-ion intercalation and deintercalation for high-rate capability. Furthermore, the hierarchical porous structure with built-in cavities facilitates the Na-ion transfer and effectively accommodates the electrode’s volume expansion, achieving fast electrode kinetics and outstanding cyclability. Such a combination of favored properties leads to state-of-the-art comprehensive battery performance for Na-ion storage. Our finding envisions a new perspective on building stable high-capacity anode materials for SIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4322-4
Ultrafast scintillators with low-nanosecond emission are essential for next-generation high-rate X-ray and particle imaging. Although Ce3+-activated scintillators inherently exhibit fast response characteristics, conventional Ce3+-doped hosts rarely achieve low-nanosecond ultrafast decay. Here, we report a high-entropy fluoride scintillator (HEFS), Ce:LaGdCaSrBaF12 (Ce:LGCSB), in the form of bulk single crystals. The severe lattice distortion arising from multi-cation disorder induces exciton localization and effectively suppresses exciton diffusion. Through the rapid relaxation of localized excitons, the high-entropy Ce:LGCSB single crystals deliver a decay time of 1.23 ns with a 94.6% fast-component contribution and without any noticeable slow component. Through first-principles calculations, spectroscopic characterization, and transient dynamics analysis, we reveal that the ultrafast response originates from accelerated Frenkel exciton (FE) recombination enabled by the high-entropy environment. This work establishes entropy-engineered fluorides as promising ultrafast scintillator platforms and proposes a general strategy for extending sluggish diffusion effects to the excitonic scale, offering new opportunities for improving scintillation timing performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3583-6
Water scarcity and the increasing demand for clean water have driven the development of efficient solar desalination technologies. Interfacial solar steam generation (ISSG) is promising, yet its practical deployment is hindered by insufficient light harvesting and salt crystallization on photothermal surfaces. Here, we report a Janus hydrogel evaporator in which tubular Co9S8 nanocrystals are uniformly embedded in a polyvinyl alcohol (PVA) matrix with a concave pyramid pattern, creating a broadband light-trapping architecture (200–2500 nm) with 96% solar absorption. The top surface is further coated with hydrophobic zeolitic imidazolate framework-8 (ZIF-8), while the bottom retains intrinsic hydrogel hydrophilicity, establishing asymmetric wettability that sustains rapid water supply yet suppresses salt deposition. Under one-sun illumination (1 kW m−2), the Janus evaporator achieves an evaporation rate of 2.69 kg m−2 h−1 and a solar-to-vapor efficiency of 98.15%. Continuous operation in 3.5 wt% brine shows stable performance for 11 h without observable salt crystallization. This work offers an effective, durable pathway toward high-performance solar desalination and wastewater purification.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3793-9
Organic solar cells (OSCs) require both a high donor/acceptor (D/A) interfacial area for efficient exciton dissociation and a vertically phase-separated morphology for efficient charge transport. Traditional bulk heterojunctions (BHJs) provide large interfacial areas but lack vertical phase separation, while quasi-planar heterojunctions (QPHJs) achieve vertical separation at the cost of reduced interfacial contact. Here, we introduce an in situ pore-forming strategy for polymer thin films. By incorporating an excess of additives as pore-forming agents into the donor layer, a nanoporous film with a fibrous nano-network is generated. Subsequent deposition of acceptor molecules fills these nanopores, creating a hybrid planar/bulk heterojunction (HP/BHJ) that synergizes the strengths of both architectures. This design enhances performance by: (1) increasing the D/A interfacial area via nanopores, forming a three-dimensional network that accelerates exciton dissociation; (2) promoting close molecular packing that minimizes carrier recombination and establishes low-defect charge transport channels; and (3) fostering vertical phase separation through layer-by-layer deposition. Binary OSCs fabricated with this strategy achieve a power conversion efficiency (PCE) of 20.0%, surpassing conventional BHJ and QPHJ devices by a significant margin. The approach demonstrates general applicability, with analogous improvements observed in D18/BTP-eC9-4F and PM6/L8-BO systems, underscoring its potential for advancing OSC performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3615-1
Stretchable electronics are pivotal for bio-integrated devices, soft robotics, and wearables, yet their development is constrained by single-layer architectures that limit integration density and by mechanical mismatch between rigid components and soft substrates, which curtails service life. Here, we introduce a LEGO-like modular assembly strategy to construct multilayer three-dimensional (3D) stretchable electronics. Electronic components (ECs) and self-healing polyurethane (SPU) substrates patterned with liquid metal (LM) circuits serve as the modular blocks. This design simplifies fabrication and markedly enhances 3D integration density. The combination of LM circuits and self-healing elastic substrates enables devices to withstand diverse deformations and to autonomously heal after mechanical damage. Notably, the devices can undergo multiple recycling and reuse cycles without significant performance loss. This methodology offers a new paradigm for advanced flexible electronics, addressing critical bottlenecks in integration density, mechanical robustness, and sustainability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3647-4
Chromium oxides (CrOx) and fluorinated graphite (CFx) are two typical cathode materials for lithium primary batteries. The former possesses the highest theoretical energy density but suffers from low practical capacity and inferior rate capability; the latter has the highest theoretical discharge capacity but fails to support fast discharge. Combining the merits of both cathodes via a composite design is desirable, yet the electrochemical performance of such composites remains unsatisfactory. In this work, we identified that by regulating the overlapped discharge potential of these two cathodes, fluorine atoms migrate from CFx to CrOx, leading to a homogeneous distribution of LiF and improved ionic and electronic conductivity, ultimately enhancing high-rate discharge performance. Benefiting from this synergetic effect, the CrOx/10%eCFx composite exhibits a considerably high energy density of 496.59 Wh kg−1 at a power density of 49.7 kW kg−1 (50 C), far superior to pure CrOx and CFx electrodes. We believe that the high-performance CrOx/eCFx composite cathode will justify its practical application in revitalizing advanced lithium primary batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3616-8
Negative stiffness (NS) structures exploit multi-stable mechanisms to achieve energy absorption, yet their practical application is limited by material and manufacturing constraints that compromise load-bearing capacity, reusability, and energy absorption efficiency. This study addresses these limitations by employing continuous carbon fiber reinforced thermoplastic polymers (CCFRTP) and three-dimensional (3D) printing to fabricate NS structures with cosine beam cells. A wet twisting method for continuous carbon fiber (CCF) was developed to enhance mechanical properties and elucidate failure behaviors and interfacial adhesion mechanisms. The resulting CCF/PLA/PVDF composites exhibited significant improvements in mechanical properties compared to untreated counterparts, with failure analysis revealing characteristic fiber breakage due to enhanced interfacial adhesion, as opposed to fiber pull-out and irregular fracture in untreated samples. A one-stroke path planning model was used to investigate bistability principles and energy absorption mechanisms. Displacement-controlled loading/unloading experiments assessed energy absorption in both energy-locked and repetitive modes. A dual-unit assembly structure was fabricated to validate the feasibility of a negative stiffness honeycomb structure. Composite layup simulations via Abaqus confirmed the deformation process and energy absorption mechanisms. The findings demonstrate that CCFRTP-based NS structures offer considerable potential for large deformation energy absorption applications in aerospace and naval fields.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3686-6
Fused silica (SiO2) exhibits exceptional thermal stability and dielectric properties, making it an attractive material for aerospace and military applications. However, its relatively poor mechanical performance has limited its widespread practical utilization. This study proposed an innovative approach to fabricate SiO2-hexagonal boron nitride (hBN) composite ceramics via spark plasma sintering (SPS), leveraging the high-temperature phase transformation of cubic boron nitride (cBN) to introduce randomly oriented hBN as a reinforcing phase within the SiO2 matrix. The randomly oriented hBN nanoplates allow cracks to propagate along stronger grain boundaries, rather than along weaker interlayers of hBN, significantly improving the overall strength and fracture toughness of the composite. The maximum flexural strength and fracture toughness achieved are 183.4 MPa and 2.06 MPa m1/2 respectively, which are 3.6 times and 4 times that of fused SiO2. Concurrently, the composites exhibit low dielectric constants (ε = 3.58–3.69) and dielectric losses (tan δ < 0.0087) at 1 MHz. This work successfully enhanced the mechanical performance of fused SiO2 while preserving its excellent dielectric characteristics, opening new possibilities for its potential applications in advanced structural and functional fields.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3705-5
Biodegradable metals (BMs) are designed to corrode gradually in physiological environments, yet this corrosion can compromise their mechanical integrity, potentially causing premature implant failure. For emerging zinc-based alloys, the corrosion-mechanical property relationship remains inadequately characterized. This study systematically investigated the long-term corrosion-associated mechanical behavior of hot-extruded Zn-Cu and Zn-Cu-Fe alloys, promising Zn-based bio-metals, in comparison with pure Zn, under immersion degradation in Hank's solution. Electrochemical impedance spectroscopy and mechanical testing revealed that the evolving corrosion profile governs mechanical performance. Alloying with Cu and Fe mitigated corrosion's detrimental effects: grain refinement reduced localized corrosion susceptibility, while finely dispersed second phases acted as cathodic sites, promoting uniform corrosion. Additionally, Cu and Fe facilitated the formation of protective corrosion product layers, suppressing further matrix attack. Consequently, the overall reduced corrosion, particularly localized corrosion, lowered stress concentration susceptibility, delaying mechanical decline and preserving structural integrity. These findings elucidate the degradation-mechanical property correlation in Zn-based bio-metals and underscore critical considerations for developing new bio-metals for clinical translation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3707-8
Wound infection is a major cause of death during the wound healing process. Improperly dressed wounds can lead to secondary injury, prolonging healing time and increasing infection risk. Here, we propose an antibacterial slippery dressing through molecular engineering of copper ions. The oil layer forms a barrier to reduce clot adhesion to the wound site and prevent environmental contamination. Single-cell level detection indicates that secreted copper ions induce bacterial death not only by disrupting membrane integrity but also by relying on the production of reactive oxygen species. Further membrane depolarization and adenosine triphosphate production blockage result in the aggregation of important proteins in various biological processes, such as metabolic homeostasis, ultimately leading to bacterial death. The animal model confirms that our dressing accelerates wound healing by promoting the growth of granulation tissue and collagen deposition. Our dressing demonstrates significant clinical implications for the design of next-generation therapeutic applications.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61068-2
The poor interface contact between bismuth (Bi) nanoparticles and reduced graphene oxide (rGO) impedes ion/electron transfer in lithium-ion battery anodes. We report an innovative fabrication of ultrafine Bi nanocrystals chemically bonded to rGO (Bi-rGO) via liquid-phase pulsed laser irradiation followed by solvothermal reaction with graphene oxide. Metastable Bi nanocrystals synthesized by laser (5.5 nm) undergo lattice restructuring and shrink to a record-small size of 2 nm during solvothermal combination, the smallest reported for Bi/C composites. The Bi nanocrystals are uniformly anchored onto rGO nanosheets via strong Bi–O–C bonds, which suppress particle aggregation, establish efficient ion/electron transport channels, and alleviate volume expansion during lithiation. The Bi-rGO-2 anode, comprising 2 nm Bi nanocrystals, delivers an exceptional reversible capacity of 586.7 mAh g−1 over 500 cycles at 100 mA g−1, nearly doubling that of a Bulk Bi/rGO composite anode (318 mAh g−1). Theoretical calculations confirm higher binding energy between Bi and rGO at smaller particle sizes, while kinetic analysis reveals accelerated Li+ diffusion. This work provides a scalable route to high-performance alloy anodes through metastable nanocrystal engineering and covalent interface coupling.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61067-0
The reduction of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP) in wastewater faces challenges in conversion rate and stability. We used coal tar pitch-based activated carbon fibers (ACFs) as a support material for loading transition metal catalysts to catalyze the reaction. Fe–Ni nanoparticles were loaded onto the coal tar pitch-based ACF through a simple hydrothermal–calcination method. The results showed that the coal tar pitch-based ACFs had a high specific surface area (1847 m2/g) and a unique microporous structure, and the metals were loaded onto them. The average diameter of the nanoparticles formed was approximately 100 nm. By changing the metal loading it was shown that the performance was best when the reaction temperature was 45 °C, the 4-NP concentration was 2.5 mmol L−1, and the molar concentration ratio of Fe3+ to Ni2+ was 1∶2 (total 7.5 mmol L−1). Under these conditions the conversion efficiency reached 99.88%. Fe2.5/Ni5–ACF exhibited excellent catalytic activity and recyclability for 4-NP after five cycles. The inherent advantages of nanomaterials increase the catalytic efficiency of 4-NP, which expands the use of coal tar pitch-based ACFs as supporting materials in the field of catalysis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3762-9
The integration of interfacial photothermal conversion and hydrovoltaic effects into bifunctional evaporators offers a promising route to simultaneously address freshwater scarcity and energy demands. However, the development of low-cost bifunctional evaporators and elucidation of the underlying co-generation mechanism remain challenging. Here, we report a porous carbon derived from waste polyester via a metal-organic framework (MOF)-assisted carbonization strategy, which is subsequently fabricated into a bifunctional evaporator for freshwater and hydroelectricity co-generation. The porous carbon exhibits a high specific surface area of 904 m² g⁻¹, hierarchical micro- and mesopores, and abundant oxygen-containing groups. The resulting evaporator demonstrates broadband light absorption, localized thermal management, good hydrophilicity, and high flexibility. Under 1 sun illumination, it achieves an open-circuit voltage of 250 mV, a short-circuit current of 14 μA, and an evaporation rate of 2.34 kg m⁻² h⁻¹, ranking among the most efficient freshwater-hydroelectricity co-generators. The weakened hydrogen-bonding network reduces the water evaporation enthalpy to 1.7 kJ g⁻¹. Mechanistic studies, including molecular dynamics simulations, reveal that selective Na⁺ interaction induces differential ion migration rates, generating a streaming potential. Additionally, the photothermal effect enhances voltage output by promoting interfacial ion concentration gradients. Outdoor tests confirm stable voltage output of 250 mV and freshwater production of 2.34 kg m⁻². This work provides a scalable platform for fabricating advanced evaporators from waste plastics and unravels the co-generation mechanism, offering a sustainable strategy to mitigate freshwater and energy crises.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3725-1
Conductive hydrogel-based stretchable electronics have been extensively investigated, with strain sensors being the most prominently studied. While mechanical properties significantly affect device performance, the systematic correlation between specific mechanical parameters and sensing performance remains rarely explored. This work compares the influences of Young’s modulus and mechanical hysteresis on sensing performance between highly entangled PAM-Li and double-network PAM-Li-Agar-3 strain sensors. Owing to the brittle agar network, which imparts a higher Young’s modulus and pronounced mechanical hysteresis to the double-network PAM-Li-Agar-3 hydrogel, the corresponding sensor requires a greater driving force for deformation and yields signals with poor reproducibility. In contrast, the PAM-Li hydrogel, characterized by highly entangled polymer chains, exhibits a lower Young’s modulus and negligible mechanical hysteresis. Consequently, signals from the PAM-Li strain sensor demonstrate enhanced sensitivity and stability. Therefore, this work demonstrates that a low Young’s modulus and minimal mechanical hysteresis are critical factors for achieving superior sensing performance in strain sensors, as systematically validated through comparative analyses across diverse application scenarios.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3772-y
Conformal contact between functional electronic films and biological surfaces is critical for long-term device stability, high signal sensitivity, and favorable signal-to-noise ratio. Traditional transfer methods, such as soft stamps and pad printing, often involve mechanical pressing, leading to poor conformality, localized stress concentration, or structural failure. Alternative strategies, including geometric engineering of non-stretchable materials or using stretchable organic alternatives, mitigate these issues but increase design complexity and reduce fabrication efficiency. Here, we highlight a novel 'drop-printing' strategy introduced by Li et al. that leverages capillary force to manipulate a water droplet to pick up a thin film, transfer it to a target substrate, and print it onto the surface. As the droplet evaporates, the film conformally wraps the surface. The droplet acts as a lubricating layer, while interfacial liquid penetrating microstructures generates capillary pressure, facilitating shape-adaptive deformation and significantly reducing stress concentration. The final positioning and conformality are governed by droplet behavior on the target surface. This approach achieves positional deviation of less than 20 μm via regulation of three-phase contact lines. The strategy enables damage-free conformal wrapping of non-stretchable films onto three-dimensional biological surfaces, as demonstrated by drop-printed silicon microfilm conformally wrapping on a rat brain, with successful NIR laser stimulation triggering forelimb movement and synchronized brain electrophysiological signals. This gentle, high-precision method addresses the pressing need for low-stress conformal bioelectronics, offering a general solution for diverse biological interfaces.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507021
The accumulation of heavy metals in soil around municipal solid waste landfills poses potential risks to human health. This study selected a municipal solid waste landfill and monitored the concentrations of eight heavy metals (Zn, Pb, Cd, Ni, Hg, Cu, As, Cr) in surrounding soil. The geo-accumulation index method was used for pollution assessment, and a health risk assessment model recommended by the USEPA, combined with Monte Carlo uncertainty analysis, was employed to evaluate the pollution status and health risks to nearby residents. Results showed that among the eight metals, Pb, Ni, and Cd exceeded risk screening values at 4.26%, 6.38%, and 4.26% of sampling points, respectively. Geo-accumulation indices indicated overall clean conditions (mean < 0), but slight pollution by Pb, Zn, Ni, Hg, and Cd at some points. Probabilistic risk assessment based on Monte Carlo simulation revealed that for both adults and children, the cumulative non-carcinogenic risk was negligible, while carcinogenic risk was acceptable. However, there was a very low probability (approximately 0.2%) of non-carcinogenic risk for children, and probabilities of unacceptable carcinogenic risk were 0.64% for adults and 3.21% for children. Nickel was the primary contributor to carcinogenic risk, and children faced higher health risks than adults. These findings provide a reference for pollution prevention and health risk management of soil around municipal solid waste landfills.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025062404
To investigate the pollution characteristics and temporal variations of water-soluble ions in atmospheric fine particulate matter (PM2.5) during autumn and winter in Taiyuan City, continuous sampling and analysis were conducted using a Swiss Metrohm ion chromatograph in autumn and winter 2023. The results show that the daily mean concentration of nine water-soluble ions was 26.04 μg m−3, accounting for 52.1% of the average PM2.5 mass concentration. Ion concentrations ranked in descending order: NO3−, NH4+, SO42−, Cl−, K+, Na+, Ca2+, F−, and Mg2+. Secondary inorganic ions (SNA) constituted 87.6% of total water-soluble ions. The mass ratio of NO3− to SO42− reached 1.83, indicating a shift from sulfate-dominated to nitrate-dominated aerosol chemistry. During pollution episodes, water-soluble ion concentrations increased exponentially, with distinct ion-specific trends: on moderately polluted days, SO42− increased to 5.31 times that on clean days, whereas on heavily polluted days, NO3− increased to 5.37 times, highlighting nitrate as a primary driver of severe pollution. Comparison with historical data reveals a recent increase in the proportion of water-soluble ions in PM2.5, with higher proportions during more polluted periods. Analysis of NH4+ forms and PM2.5 acidity suggests that acidic components contribute more under heavier pollution. Positive matrix factorization (PMF) identified four major sources: secondary sources, combustion and motor vehicles, industrial sources, and dust. The secondary source contributions were 45.4%, 64.7%, and 63.4% on clean, lightly polluted, and moderate-to-heavy polluted days, respectively, indicating a significantly higher secondary contribution on polluted days.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3451-2
Visual aesthetics is a key metric of semi-transparent organic photovoltaics (ST-OPVs) for building-integrated solar windows, yet previous studies have primarily focused on the compromise between efficiency and transparency. This work addresses the overlooked aspect of full visual aesthetic control, particularly the bidirectional reflected color for architectural harmony, via designing ST-OPVs with double-sided ultra-thin Ag/TeO2 transparent electrodes. This design facilitates full-spectrum color tunability covering the whole standard color gamut of CIE coordinates on both surfaces, achieved simply by adjusting layer thicknesses. The resulting devices exhibit neutral transparency (16.6%–27.0% average visible transmittance) and competitive power conversion efficiencies (8.1%–9.2%). Additionally, the devices demonstrate strong flexibility, with flexibility-adaptive coloration and curvature-enhanced aesthetics. This work presents an ST-OPV design featuring full visual aesthetics and considerable performance, paving the way for commercialization of organic solar windows for building and vehicle integration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3470-6
Inkjet printing of two-dimensional transition metal chalcogenides (TMDs) is promising for low-cost, large-scale flexible electronics, yet challenges persist due to poor crystallinity and toxic solvents. Here, we report a green ink formulation using zwitterionic cocamidopropyl betaine (CAB) as a dispersant and surfactant for liquid-phase exfoliation of single-crystalline TMDs in water and isopropanol (IPA). The dispersions contain no additives or binders, enabling direct production of stable (over one month) and concentrated (2 mg/mL) inks for MoS2, MoTe2, WS2, WSe2, and WTe2. Fully-printed MoSe2/CAB humidity sensors exhibit superior sensitivity (ΔI/I0 = 468.1) and rapid response/recovery times (27 s/0.42 s) under bending. Inkjet-printed WTe2/CAB pads on 6-μm-thick substrates demonstrate exceptional mechanical stability, with resistance variations of 1.4% under single bending and 2% after 1,000 cycles, and acquire high-quality electrocardiogram (ECG) and electromyography (EMG) signals. This strategy enables scalable fabrication of TMD-based flexible electronics, advancing industrial integration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3545-7
Magnetically driven hydrogel robots show promise in biomedical and underwater applications due to remote controllability, flexibility, biocompatibility, and chemical stability. However, limited functional integration restricts their adaptability. Here, a universal modular assembly strategy is introduced using a self-healing κ-carrageenan/polyacrylamide hydrogel embedded with magnetic particles, enabling free assembly of magnetic actuation modules. These modules construct soft robots with complex geometries and magnetization distributions, allowing diverse deformations under magnetic fields. The strategy further integrates photocatalysis by embedding Ru-Bi2CrO6 photocatalysts into functional modules, yielding an oxygen-generating robot. This robot exhibits flexible underwater movement via magnetically controlled oscillatory actuation, minimizing water agitation while supplying stable oxygen to specific aquatic environments. The photocatalytic oxygen evolution rate reaches 389.1 μmol g−1 h−1. The hydrogel skeleton suppresses particle aggregation and sedimentation, and facilitates magnetic recovery. This scalable and adaptable approach advances multifunctional soft robot design.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60644-5
Lignin, as the sole renewable source of aromatic compounds, holds significant potential for producing green aviation fuel-range arenes via hydrodeoxygenation (HDO). In this study, a series of nitrogen-doped carbon-supported FeMoS/NC bimetallic catalysts were synthesized via a hydrothermal method. The HDO performance was evaluated using 4-ethylguaiacol as a model compound at 340 °C under 3 MPa H2. The unmodified MoS2/NC catalyst achieved a deoxygenation degree of 83.4%, whereas the Fe-modified catalyst with an optimal Fe/Mo molar ratio of 0.3 (Fe0.3MoS/NC) attained complete deoxygenation (100%) with an arenes selectivity of 78.6%. Beyond this optimal ratio, the deoxygenation degree inversely correlated with the Fe/Mo molar ratio. Characterization via XRD, TEM, BET, and XPS revealed that Fe incorporation enhanced the uniform dispersion of MoS2 on the NC support, increased surface acidity, and raised the concentration of sulfur vacancies, thereby promoting adsorption of oxygen-containing compounds. The HDO pathway over Fe0.3MoS/NC primarily proceeded via direct deoxygenation. When applied to real lignin under identical conditions (340 °C, 3 MPa H2, 12 h), the catalyst yielded 65.5% green hydrocarbons, with the C8–C16 fraction accounting for 54.4% of total hydrocarbons and an aromatic selectivity of 63.4% within this fraction. These results demonstrate that Fe0.3MoS/NC is a viable catalyst for selective conversion of lignin into green arenes suitable for sustainable aviation fuel applications.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605014
Chlorinated aliphatic hydrocarbons (CAHs) are prevalent groundwater contaminants at industrial sites in China. This pilot-scale study evaluated in-situ anaerobic bioremediation of CAHs-contaminated groundwater in a low-permeability bedrock fracture zone at depths up to 40 m. A self-developed anaerobic dechlorinating culture (BS-1), containing Dehalococcoides, Desulfitobacterium, and Dehalogenimonas, was injected alongside carbon sources (sodium citrate and emulsified vegetable oil) and nutrients. Pressurized nitrogen gas injection enhanced the distribution of amendments, achieving a radius of influence of 5.0 m. Over 399 days of monitoring, the combined use of slow-release and soluble carbon sources maintained anaerobic conditions (ORP < -100 mV) for over one year, providing sustained electron donors. The emulsified vegetable oil reduced injection frequency and operational costs. The BS-1 culture effectively dechlorinated vinyl chloride, cis-1,2-dichloroethylene, trichloroethylene, and chloroform, achieving removal efficiencies exceeding 95%. At times, groundwater quality met the Class IV standard of GB/T 14848-2017. This study demonstrates a green, economical, and effective solution for CAH-contaminated site remediation, with significant engineering application potential.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509095
Biotrickling filtration (BTF) is a promising technology for treating volatile organic compounds (VOCs), but its application to hydrophobic alkanes like isohexane is hindered by mass transfer limitations, low degradation efficiency, and high operational costs. To address these bottlenecks, this study developed composite fillers by incorporating biochars derived from coffee grounds (CG), coconut shells (CS), corn cobs (CC), and activated carbon (AC) into a polyvinyl alcohol-sodium alginate (PVA-SA) hydrogel matrix. The fillers were systematically characterized for water retention, pore structure, surface functional groups, crystalline phase, and acid-base resistance. Adsorption capacity, biofilm formation, and isohexane degradation were evaluated using the strain Rhodococcus ruber ZYH-ZY. Among the composites, CG@PVA-SA exhibited superior performance: water retention of 358 mg·g−1 (vs. 280 mg·g−1 for control), enhanced mesoporosity (specific surface area 4.77 m2·g−1, pore volume 11.46 cm3·kg−1, 10–30% higher than control), and robust acid-base stability (mass loss 21.37% at pH 2 and 31.98% at pH 10). Its saturated adsorption capacity reached 201.02 mg·kg−1 (vs. 114.24 mg·kg−1 for control), and it promoted bacterial colonization with a survival rate of 79.0% (vs. 37.2% for control). Static degradation tests showed 96.59% removal of 10 μL isohexane within 24 h. The abundant polar functional groups and suitable mesoporous structure of coffee ground biochar synergized with the PVA-SA matrix, enhancing water retention, mass transfer, and microbial colonization, thereby significantly improving isohexane purification. CG@PVA-SA is an ideal filler for BTF treatment of alkane VOCs, offering a cost-effective and efficient solution for industrial VOC control.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60652-4
The performance of industrial zeolite catalysts, exemplified by fluid catalytic cracking (FCC) catalysts, is governed by microscopic behaviors including mass transfer, acidity, and coking. Conventional characterization techniques such as XRD, N2 physisorption, and TPD provide bulk-averaged or static ex situ information, failing to resolve dynamic processes under realistic reaction conditions. Recent advances in super-resolution fluorescence imaging enable nanoscale visualization of these key processes. This review systematically summarizes three critical applications: (1) Mass transfer diffusion: heterogeneous diffusion of reactant molecules within hierarchical pore networks is revealed, quantifying diffusion barriers and tortuosity. (2) Acid site accessibility: nanoscale localization of acid sites and their accessibility is achieved, correlating with catalytic activity. (3) Coking behavior: spatiotemporal evolution of coke species is identified, linking coke precursors to deactivation. The review elaborates how super-resolution imaging deepens understanding of fundamental catalytic mechanisms, providing theoretical support for rational design of high-performance catalysts through pore structure optimization, acid site regulation, and coking suppression. Current challenges and future directions are discussed, emphasizing the need for in situ correlation with catalytic performance.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025120801
The interaction between microplastic-derived dissolved organic matter (PSDOM) and iron oxides in soil environments can modulate its photosensitization effects, yet the underlying mechanisms remain elusive. This study investigated the influence of hematite with distinct morphologies—flake-shaped (HNPs) and cubic (HNCs)—on the photosensitization of polystyrene-derived dissolved organic matter (PSDOM). Under 500 W mercury lamp irradiation, both hematite morphologies promoted PSDOM degradation, with HNCs exhibiting superior performance: total organic carbon (TOC) decreased from 18.4 mg·L−1 to 12.3 mg·L−1 within 90 min, compared to 13.3 mg·L−1 for HNPs. Three-dimensional fluorescence spectroscopy indicated that hematite alters the humification process, thereby modifying photosensitization. Electron paramagnetic resonance (EPR) spectroscopy identified the generation of singlet oxygen (1O2), hydroxyl radicals (·OH), and carbon-centered radicals (CH3C(=O)OO·). HNCs significantly enhanced 1O2 production, while HNPs favored ·OH generation; both inhibited CH3C(=O)OO· formation. Quantitative analysis via high-performance liquid chromatography revealed that the steady-state concentration of 1O2 was highest with HNCs, reaching 2.80 times that of the PSDOM control, whereas ·OH concentration peaked with HNPs at 1.98 times the control. Notably, the steady-state concentration of 1O2 was approximately three orders of magnitude higher than that of ·OH. These findings elucidate the morphology-dependent role of hematite in PSDOM photosensitization, providing mechanistic insights into the environmental fate of microplastic-derived organic matter in complex soil systems.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606014
Microplastics, as emerging environmental pollutants, can adsorb psychotropic drugs in aquatic environments, facilitating their migration and transformation, ultimately posing ecological risks. This study investigated the adsorption behavior and mechanisms of four common microplastics—polyethylene (PE), polypropylene (PP), polystyrene (PS), and polyvinyl chloride (PVC)—each with a particle size of 50 μm, toward three psychoactive drugs: diazepam, fluoxetine, and mianserin. Adsorption kinetics, isotherms, and the effects of pH and salinity were examined. Kinetic data fitted well to a pseudo-second-order model, indicating chemisorption as the rate-limiting step. Isotherm analysis using Langmuir and Freundlich models revealed that PE exhibited the highest affinity for fluoxetine, PP for mianserin, and PVC for diazepam, while PS showed linear adsorption for fluoxetine, suggesting partitioning. The adsorption of diazepam was maximal at pH 6.5–8.5, typical of natural surface waters, and increased with NaCl concentration, indicating that non-electrostatic interactions dominate and that higher ionic strength enhances adsorption. Mechanistic insights suggest that hydrophobic interactions, hydrogen bonding, π-π interactions (for PS), and halogen bonding (for fluoxetine) contribute to adsorption. These findings highlight the potential of microplastics to act as vectors for psychoactive drugs, necessitating further research on their environmental fate and ecological implications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3820-5
Two novel N-heterocyclic carbene (NHC)-based ligands featuring rigid boron-oxygen (BO) fused-ring units, named Bpmi and Bpmb, and the two corresponding homoleptic meridianal iridium complexes, namely mer-Ir(Bpmi)3 and mer-Ir(Bpmb)3, were designed and synthesized. Single-crystal structures revealed a meridional coordination geometry for both complexes. Shorter Ir–C carbene bond lengths and rigid planar BO-fused ring units contribute to enhanced stability. Both complexes exhibit efficient green phosphorescence (λem = 536/521 nm in toluene, ΦPL > 78%) with short lifetimes (τ = 846/1083 ns), leading to high radiative rate constants (Kr = 10.04 × 10^5 and 7.29 × 10^5 s−1, respectively). Theoretical calculations indicate significantly increased metal-to-ligand charge transfer (MLCT) character (21.69% for mer-Ir(Bpmi)3; 17.30% for mer-Ir(Bpmb)3) compared to reference complexes (13.01% for mer-Ir(pmi)3; 15.99% for mer-Ir(pmb)3). Both complexes exhibit exceptional thermal stability with decomposition temperatures of 491°C (mer-Ir(Bpmi)3) and 540°C (mer-Ir(Bpmb)3). OLED devices using mer-Ir(Bpmb)3 and mer-Ir(Bpmi)3 as emitters demonstrate maximum external quantum efficiencies of 20.0% and 15.6%, respectively. This research pioneers boron-fused ring-containing NHCs and their phosphorescent iridium(III) complexes, establishing a novel design strategy for high-performance NHC-based OLED phosphorescent emitters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3774-3
Lithium-air capacitor batteries (LACBs) integrate the rapid charge-discharge capability of supercapacitors into conventional lithium-oxygen batteries, significantly enhancing power density. However, their cycling stability remains unsatisfactory. In this study, we incorporated redox mediators (RMs) into an LACB featuring a dual-cathode configuration. This design facilitates sustained electron transfer between the electrode and Li2O2/Oxygen, thereby delaying RM deactivation caused by electrode passivation and improving overall electrochemical performance. The RM-enhanced battery achieved over 250 cycles at 2 mA cm−2 with a limited capacity of 0.5 mAh cm−2, while exhibiting a 0.54 V reduction in charging voltage at 0.1 mA cm−2 compared to the RM-free system. Furthermore, application of an aluminum foil sealing technique enabled a power density of 13.8 mW cm−2 at 6 mA cm−2, overcoming mass transport limitations inherent in open-cell configurations. We also investigated the influence of oxygen barrier films with varying barrier capabilities on LACB performance. Results indicate that films with superior oxygen resistance better maintain a clean capacitor electrode surface, thereby providing more stable electron supply to the RMs and enhancing rate capability and cycling performance. These findings underscore the potential of redox mediators in improving the performance and longevity of LACBs, offering a promising strategy for their future development.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3851-3
Aqueous zinc-ion batteries (AZIBs) face critical challenges from zinc anode instability, including corrosion, hydrogen evolution reaction (HER), parasitic byproduct formation, and uncontrolled dendrite growth. To address these issues, we developed a multifunctional cerium-based metal-organic framework (Ce-MOF) coating for zinc anodes. The coating features an ordered porous structure and inherent properties that mitigate HER, suppress side reactions, and inhibit dendrite formation. Symmetric cells using Ce-MOF/Zn demonstrated exceptional cycling stability for over 2060 h at 0.5 mA cm−2 with a low hysteresis polarization of 26 mV. In full cells with an I2@AC cathode, the Ce-MOF/Zn||I2@AC achieved outstanding cycling stability of 28,550 cycles at 5 A g−1, with 91% capacity retention (109.6 mAh g−1). Through integrated characterization employing in-situ optical microscopy, ex-situ XRD, SEM, and DFT calculations, we elucidated the multifunctional mechanism: the Ce-MOF coating facilitates preferential (002)-oriented Zn deposition to suppress dendrites, reduces Zn2+ desolvation energy to enhance deposition kinetics, and modulates interfacial chemistry to mitigate HER and corrosion. This work establishes Ce-MOF coatings as a simple yet powerful strategy for developing high-performance zinc anodes, providing critical insights for advancing practical AZIB technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3944-9
Hard carbon (HC) is a promising anode material for sodium-ion batteries (SIBs) but suffers from low initial Coulombic efficiency (ICE) and unstable solid electrolyte interphase (SEI). Here, we report a dual-functional strategy combining surface engineering and solution chemical pre-sodiation. A graphitic carbon coating on HC acts as a conductive buffer network and shields surface defects, while sodium biphenyl (Na-Bp) pre-sodiation drives sodium ions into the material via a potential difference, inducing a pre-SEI layer that matures into a thin, dense, NaF-rich inorganic SEI during cycling. This approach compensates for irreversible sodium loss and enhances cycling stability. The pre-sodiated electrode (pCH4-HC) achieves an ICE of 99.5% and a reversible capacity of 321.7 mAh g−1, compared to 54.2% for untreated HC. Long-term cycling shows 74.0% capacity retention after 1000 cycles at 300 mA g−1. In full-cells with NaNi1/3Fe1/3Mn1/3O2 (NFM) cathode, pCH4-HC||NFM delivers 81.9 mAh g−1 after 100 cycles, demonstrating excellent stability and rate performance. This dual-strategy approach validates the adaptability of pre-sodiation technology for high-performance SIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3976-x
The discovery of high-temperature superconductivity in bilayer nickelate La3Ni2O7−δ (La-327) under high pressure and in thin films at ambient pressure has opened new avenues in superconductivity research. However, La-327 exhibits a narrow phase stability range, leading to stacking faults that suppress bulk superconductivity. Chemical substitutions, particularly at the A-site with smaller rare-earth ions, have been shown to enhance phase purity and reduce stacking faults, while also increasing the orthorhombic distortion and chemical pressure. In this work, we apply the high-entropy (HE) strategy to stabilize the 327 phase with reduced average A-site ionic radius (rA). We successfully synthesized medium-entropy La1.2Pr0.6Nd0.6Sm0.6Ni2O7−δ (ME-327) and high-entropy La0.67Pr0.67Nd0.67Sm0.33Eu0.33Gd0.33Ni2O7−δ (HE-327) polycrystalline samples. These compositions satisfy medium- and high-entropy criteria, with rA values of 1.181 Å and 1.164 Å, respectively. The samples are phase-pure and homogeneous. HE-327 exhibits the lowest cell volume, largest orthorhombicity, and shortest interlayer Ni-Ni distance among reported bilayer nickelates. Physical property measurements reveal low electrical conductivity and a high density-wave (DW) transition temperature. Under high pressure, HE-327 shows a resistivity anomaly at 103 K under 31 GPa, suggesting a possible superconducting transition. Extrapolation indicates that Tc under high pressure exceeds 100 K for HE-327, correlating with reduced rA and enhanced interlayer coupling. Our results demonstrate the ionic size effect and the effectiveness of the HE approach in stabilizing bilayer nickelates, providing a new avenue for developing superconducting materials.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511003
Tailings dam leakage can cause secondary sudden water pollution events, imposing severe combined stress of high turbidity and heavy metal contamination on natural water bodies within a short period, threatening aquatic ecological security. Existing studies have systematically revealed the pollution characteristics and biological effects of such events, which are fundamentally distinct from natural high-turbidity water and industrial wastewater leakage. Compared with natural high-turbidity water, tailings leakage inputs finer particles with higher specific surface area, leading to more intense and prolonged turbidity stress. Meanwhile, heavy metals in tailings are more enriched than natural sediments, with higher proportions of active forms and bioavailability, causing significant bioaccumulation and toxic effects, and long-term decline in benthic community species richness. Compared with industrial wastewater leakage, tailings leakage simultaneously releases high concentrations of fine suspended solids and multiple heavy metals, forming a unique 'physical-chemical' combined stress. This synergistic effect amplifies biological toxicity through multiple pathways such as mechanical damage, light limitation, and oxidative stress, resulting in severe and often irreversible ecological damage, such as impaired fish swimming behavior and collapse of benthic community structure. Analyzing the long-term impacts of tailings leakage on aquatic ecosystems from the perspective of combined stress is helpful for providing scientific basis for emergency response and medium-to-long-term ecological risk prevention of related sudden water pollution events.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60643-3
The adsorption behavior and electron transfer mechanism of CO on Ptn/γ-Al2O3 catalysts (n = 4, 13) were systematically investigated using density functional theory (DFT) calculations, complemented by infrared (IR) spectroscopy, electron difference density (EDD), and charge decomposition analysis (CDA). The study reveals that Pt cluster size critically governs the adsorption configuration, electron transfer, and C–O vibrational frequency. For small Pt4 sub-nanometric clusters, highly unsaturated Pt atoms exhibit strong d-electron back-donation, leading to substantial filling of CO π* antibonding orbitals, significant weakening of the C–O bond, and a redshift in IR frequency. Conversely, large Pt13 clusters, characterized by dense structures and electron delocalization, exhibit weakened back-donation, enhanced C–O bonding, and a blueshift. The electron transfer intensity follows the order: linear < bridge < multi-terminal adsorption. Bridge adsorption is most sensitive to cluster size, displaying an IR blueshift of 81 cm−1 when Pt atoms increase from 4 to 13. Multi-terminal adsorption shows stable frequencies due to a 'saturation effect'. This study establishes a comprehensive correlation among Pt size, electronic structure, adsorption properties, and infrared response, providing atomic-scale theoretical guidance for designing efficient Pt-based catalysts with optimized CO adsorption strength and resistance to poisoning.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0034
Catalytic cracking of gasoline and diesel to light olefins is a pivotal route for high-value utilization of surplus fuels, typically employing zeolite catalysts. This study systematically investigates the effects of zeolite type and acidic properties on the catalytic cracking of dodecane, a diesel model compound, using SAPO-34, ZSM-5 with SiO2/Al2O3 ratios of 38, 85, and 200, and USY. Catalysts were characterized by XRD, SEM, N2 physisorption, NH3-TPD, and pyridine-FTIR, and evaluated in a fixed-bed reactor. Results demonstrate that zeolite type is the primary determinant of conversion and product distribution. SAPO-34, with 0.38 nm pores, achieved only 24.33% conversion and negligible BTX yield, with severe external coking. ZSM-5-38 and USY, with larger pores, achieved near-complete conversion; however, ZSM-5-38, possessing moderate acidity, yielded the highest light olefins (18.40%) and minimal coke (0.18%), while USY, with higher acidity, promoted hydrogen transfer and coking (12.90% coke). Within ZSM-5 series, lower acid site density (ZSM-5-200) proved optimal, achieving 97.79% conversion and a total light olefin yield of 41.93% (ethylene 11.11%, propylene 20.33%, butenes 10.49%) with low coke (0.43%). The study proposes reaction pathways and regulatory mechanisms, highlighting that zeolite type and acidity govern the relative rates of cracking, hydrogen transfer, oligomerization, aromatization, and coking, thereby dictating performance. These findings provide a rational basis for optimizing zeolite catalysts in commercial gasoline/diesel cracking processes.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025040104
The oxidative transformation of 2,6-dichlorophenol (2,6-DCP) was investigated in three typical zonal soils: black soil, red soil, and brown soil. Results demonstrated that 2,6-DCP underwent oxidative coupling in all soils, yielding hydroxylated polychlorinated diphenyl ethers (OH-PCDEs) and hydroxylated polychlorinated biphenyls (OH-PCBs) as primary products. The highest oxidative efficiency occurred in black soil, with approximately 85.1% of 2,6-DCP transformed within three days. In contrast, red and brown soils exhibited lower efficiencies, indicating a strong dependence on soil properties. Thermodynamic analysis revealed that the oxidative coupling reaction is endothermic, with elevated temperatures favoring reaction progress. Furthermore, soil microorganisms and dissolved oxygen were identified as critical controlling factors, acting synergistically to drive the reaction. This study provides the first evidence of natural oxidative coupling of 2,6-DCP in soil, forming OH-PCDEs and OH-PCBs. These findings offer significant scientific insight into the environmental fate of halogenated phenolic pollutants in terrestrial systems.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607010
The impact of low concentrations of perfluorooctane sulfonate (PFOS) on anaerobic fermentation of waste activated sludge (WAS) remains poorly understood. This study applied three PFOS levels (0.5, 1.0, and 4.5 μg/g TSS) to systematically evaluate effects on organic matter solubilization and nitrogen/phosphorus transformations. Monitoring of soluble chemical oxygen demand (SCOD), soluble protein, polysaccharides, NH4+-N, PO43--P, and three-dimensional excitation-emission matrix (3D-EEM) fluorescence revealed that PFOS significantly enhanced release of SCOD, protein, and polysaccharides. At 45 °C after 14 days with 4.5 μg/g TSS, SCOD peaked approximately 28% higher than control, indicating increased biodegradable organic matter accumulation. NH4+-N concentrations rose overall with fluctuations, while PO43--P release was inhibited, suggesting interference with nutrient transformation pathways. 3D-EEM analysis showed strengthened signals of aromatic proteins and microbial by-products, confirming matrix solubilization. These findings demonstrate a dual effect of low-level PFOS: initial promotion of organic matter release followed by potential inhibition of nutrient transformation. This study provides data support for understanding PFOS environmental behavior in anaerobic digestion and informs sludge resource utilization and risk assessment of emerging contaminants.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4079-4
Utilization of ultrahigh-nickel LiNi_xCo_yMn_1-x-yO_2 (NCM) (x > 0.97) in Li-ion batteries can distinctively boost energy density through enhanced discharge capacity. However, capacity and thermal stability deteriorate as Ni content approaches the limit. Here, we propose a facile strategy by introducing high-valence tungsten (W) into ultrahigh-nickel polycrystalline LiNi_0.98Co_0.01Mn_0.01O_2 (PCNCM98). W-doped PCNCM98 (W-PCNCM98) exhibits refined, compactly stacked primary particles, whereas PCNCM98 shows equiaxial, non-uniform larger particles. The refined microstructure enhances mechanical strength: average particle hardness of W-PCNCM98 is 104 MPa, 1.5 times higher than PCNCM98 (68 MPa). This improved mechanical property suppresses lattice volume changes and relieves microcrack formation from H2–H3 phase transition. Consequently, cycling performance in pouch-type full cells is significantly enhanced, with capacity retention of 73% after 2000 cycles at 1 C and 25 °C, 54% higher than PCNCM98. Enhanced structural stability and strong electron affinity of W6+ also improve thermal stability: exothermic peak for W-PCNCM98 is postponed to 203 °C with heat generation of 1287 J g−1, versus 190 °C and 1528 J g−1 for PCNCM98. This high-valent doping strategy stabilizes ultrahigh-nickel NCM cathodes, accelerating large-scale EV applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3962-y
Photochromic Förster resonance energy transfer (pc-FRET)-based subnanometric polymersomes with accurate color control offer a transformative yet challenging tactic for advanced and custom-tailored information encryption. Herein, various amphiphilic alternating pyrene/azobenzene-containing copolymers were polymerized using one-pot Ugi four-component polycondensation. Subsequent self-assembly was performed to produce highly-integrated monolayer subnanometric polymersomes (MSNPSs) and their composites, with diameters of around ~250 nm and vesicular thicknesses of approximately ~12.0 Å. J-aggregated monolayer chain-folding mechanism was accountable for the donor-acceptor-donor stacking manner within the vesicular membrane, beneficial to achieve highly efficient energy transfer. The trans-to-cis photoisomerization of azobenzenes rendered MSNPSs and their composites with photo-triggered structural transitions in diameter and vesicular thickness. Benefitting from considerable spectral overlap between cis-azobenzene and pyrene, MSNPSs and their composites were capable of photo-controllable non-invasive pc-FRET performance with a wide Stokes shift (~320 nm). The accurate color variation from blue to red highly depended upon precise modulation of both irradiation duration and precursor-fixed donor/acceptor ratios. The proof-of-concept individually multichromatic 2D QR code was attained using photochromic MSNPSs and their composites in patterning lithography, displaying a multimodal decryption and favorable repeatability for high-level and personalized information protection. Our work paves a prospective avenue to meticulously craft stimuli-chromatic polymersomes for the potential of advanced information encryption.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511052
Microplastics in sewage sludge, owing to their diverse physicochemical properties, can differentially affect subsequent anaerobic digestion. This study focused on polyethylene terephthalate (PET) microplastics, systematically investigating the effects of particle (MP), fiber (MF), and film (MPF) morphologies at concentrations of 0–150 mg·g⁻¹ (based on total solids) on sludge digestion performance and microbial community structure. Results showed that MP inhibited total biogas production at all concentrations (inhibition rates 8.16%–9.58%), whereas MF and MPF exhibited low-concentration stimulation and high-concentration inhibition, with MPF exerting stronger inhibition than MF. All MP concentrations induced significant reactive oxygen species (ROS) accumulation (increases of 9.43%–34.52%), indicating the strongest oxidative stress. Low concentrations of PET generally enhanced cell membrane permeability, prompting microbes to secrete different extracellular polymeric substances (EPS) to resist stress. The morphology and concentration of microplastics regulated the relative abundances of key functional bacteria (e.g., proteolytic bacteria and organic acid-oxidizing bacteria) and low-abundance bacteria, ultimately leading to differences in digestion performance. This study provides a theoretical basis for efficient treatment of sludge containing microplastics.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608004
This paper presents the design and implementation of an energy-saving onsite thermal treatment system for hazardous medical organic waste liquid. The system integrates automatic control with energy-efficient and eco-friendly operation, enabling immediate treatment at the source and reducing storage and transportation volumes by over 95%. It comprises four modules: waste liquid identification, graded thermal treatment, heat recovery, and tail gas purification. The graded thermal treatment technology effectively processes waste liquids with varying compositions and calorific values. On-site experiments were conducted on four typical medical organic waste liquids over one year. Results demonstrated effective treatment meeting safety and environmental requirements, with dioxin concentrations below 0.1 ng-TEQ/m³ and CO, NOx, and SOx emissions within permissible limits. The system offers economic benefits by eliminating long-distance transport and centralized treatment costs. This approach addresses the limitations of traditional long-chain, manual-intensive disposal methods, which pose significant safety and environmental risks.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4013-y
Multicolor fluorescent polymer materials (MFPMs) are of significant value in biomaterials and display technologies due to their rich color palette. Traditional construction methods rely on incorporating multiple fluorescent molecules of different colors, which introduces complexities in structural design, synthesis, purification, and practical operability. To overcome these challenges, a strategy employing a single fluorophore that exhibits multiple fluorescent colors has been developed and integrated into MFPMs. This approach has advanced fields such as information anti-counterfeiting and optoelectronic materials. This review summarizes recent developments in MFPMs based on a single fluorescent molecule, elucidates preparation methods and color conversion mechanisms, and analyzes application prospects. Key mechanisms include aggregation-induced emission (AIE), excited-state intramolecular proton transfer (ESIPT), and twisted intramolecular charge transfer (TICT), which enable color tuning through environmental stimuli or assembly. The review highlights the potential of this strategy to simplify fabrication processes while achieving tunable emission colors. It provides guidance for designing novel multicolor fluorescent materials and fosters progress in fluorescent materials, polymer science, and materials science.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608026
Biochar and microbial inoculants are widely used for agricultural soil amendment. To investigate the effects of different straw biochars and Bacillus subtilis inoculant, applied individually or combined, on nitrogen transformation in dryland soil, a 60-day laboratory incubation experiment was conducted with six treatments: control (CK), 4% rice straw biochar (S), 4% rapeseed straw biochar (Y), 4% rice straw biochar plus 5 mg/kg inoculant (SJ), 4% rapeseed straw biochar plus 5 mg/kg inoculant (YJ), and inoculant alone (J). Results showed that rice straw biochar significantly increased soil nitrate nitrogen content by 148.74%–152.68% compared to CK, enhancing nitrification. Combined application with inoculant further increased average net nitrogen mineralization rate by 77.28%–99.38%. Conversely, rapeseed straw biochar decreased nitrate nitrogen by 51.66%–57.61%, and combined application reduced net nitrogen mineralization rate by 82.07%–84.73%. Treatments S, Y, SJ, and YJ promoted microbial biomass nitrogen (MBN) synthesis, with S and Y increasing MBN by 2.02- and 2.20-fold over CK, respectively. Combined treatments further increased MBN by 103.26%–149.44% relative to single biochar treatments. These findings indicate that biochar type governs nitrification and net nitrogen mineralization, while combined application exerts synergistic effects on MBN. For comprehensive dryland soil improvement, YJ treatment is optimal, reducing inorganic nitrogen loss risk and enhancing microbial nitrogen activity.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3987-x
A hierarchically porous nickel salicylate (Ni-SA) metal-organic framework (MOF) was constructed via a salicylate coordination strategy to precisely modulate the microenvironment of nickel active sites for efficient electrocatalytic glucose oxidation. The ortho-hydroxy-carboxylate chelation directs atomic-level organization of Ni2+ sites within nanobelt assemblies, maximizing active site accessibility. Robust Ni–O coordination stabilizes Ni3+ intermediates during C–H bond cleavage, leading to remarkable catalytic stability. The optimized Ni-SA-2 catalyst achieved a high sensitivity of 5.97 mA mM−1 cm−2 and a low detection limit of 0.71 μM (S/N = 3), with 85.4% current retention after 8 h continuous operation. This design paradigm demonstrates universal applicability, as evidenced by successful extension to isostructural M-SA analogs (M = Co, Fe, Cr, Mn) under identical synthetic conditions, establishing metal-salicylate frameworks as a versatile electrocatalyst platform.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4047-0
The proliferation of electronic devices has exacerbated electromagnetic pollution, necessitating advanced electromagnetic wave (EMW) absorbing materials. In this study, VS2 nanorods were uniformly grafted onto graphene nanosheets (GNSs) via a facile ball milling method, constructing 1D/2D hierarchical VS2@GNSs composites with superior EMW absorption properties. The minimal reflection loss (RLmin) reached -49.83 dB at a thickness of 1.83 mm, while an ultra-broad effective absorption bandwidth (EAB) of 6.72 GHz was achieved at 1.96 mm. These performances are attributed to enhanced impedance matching and EMW attenuation capacities. Computer simulation technology (CST) full-wave simulations confirmed remarkable radar cross-section (RCS) suppression, with a reduction value of up to 20.38 dB m2 compared to a metallic substrate. This work provides theoretical and experimental guidance for designing high-performance stealth materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4003-7
The escalating electromagnetic (EM) pollution necessitates the development of high-performance microwave absorbers (MAs) with integrated functionalities. However, it is still a difficult problem to integrate more related high performances into the designed MAs. Herein, a sustainable strategy was reported for fabricating three-dimensional (3D) porous magnetic Ni@C-anchored carbon foams (Ni@C/CFs) with abundant heterointerfaces and magnetic Ni@C nanoparticles using 3D porous chitosan foams and Ni-nitrilotriacetic acid chelate (Ni-NAC) as precursors. The modulation of carbonization temperature and concentration of Ni-NAC solution contributed to the tunable carbon graphitization, Ni crystallinity and magnetic Ni@C nanoparticles loading, which effectively improved their EM properties and EM wave absorption performances (EMWAPs). The optimized 3D porous magnetic Ni@C/CFs not only exhibited exceptional EMWAPs with a minimum reflection loss (RL min) of −27.58 dB and an ultra-wide effective absorption bandwidth (EAB) of 7.20 GHz, but also presented efficient thermal insulation and strong antibacterial activity (>95% inhibition against E. coli), which mainly originated from their excellent magnetic-dielectric synergies and unique 3D hierarchical porous structures. Consequently, this work delivers a coherent design strategy for next-generation multifunctional absorbers with potential applications in EM protection, thermal management, and adaptive stealth technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4044-3
Efficient sequestration of radioactive iodine species (I2, CH3I, I3−) is vital for nuclear safety and environmental protection. However, developing multifunctional adsorbents that remain effective under diverse conditions remains a significant challenge. Herein, we report two functionalized PD-COFs (PD-WS and PD-WY) with moderate crystallinity, outstanding thermal stability, and robust chemical resistance. They exhibit superior adsorption performance in both gas and liquid phases. Specifically, at 75°C, PD-WY achieves capacities of 4.88 g g−1 for I2, 1.55 g g−1 for CH3I, and 5.55 g g−1 for the I2/CH3I mixture, while high capacities are also retained at room temperature. In solution, PD-WY adsorbs up to 3.56 g g−1 of I3− in water and 2.00 g g−1 of iodine in cyclohexane. These COFs display rapid kinetics (K80% = 3.25 g g−1 h−1 for I2 and 7.89 g g−1 h−1 for I3−) and excellent selectivity. Mechanistic studies indicated that the excellent iodine affinity of PD-COFs arises from their rich electronic structures, abundant active sites, and charge transfer interactions. These findings position PD-COFs as highly promising adsorbents for nuclear waste treatment and environmental remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4045-x
The release of radioactive iodine from nuclear accidents and nuclear medicine poses significant environmental and health risks. Here, we report the design and synthesis of two cross-linked macrocycle-based porous organic polymers (P1 and P2) with different functionalities for efficient and rapid capture of radioactive iodine. P1 achieves complete iodine adsorption within 5 minutes, with an exceptional adsorption rate constant (k_obs) of 18.92 g g−1 min−1 (8.24 g g−1 min−1 for P2), representing a record-high iodine removal rate among state-of-the-art porous organic polymers. P1 demonstrates superior iodine adsorption efficacy in dynamic flow-through experiments, achieving a remarkable efficiency of 96.4% for radioactive 131I removal, greatly minimizing radiation contamination. Experimental and modelling techniques reveal that the superior iodine adsorption performance originates from electron-rich functional groups, hydrophobic surface, and porous structure of P1, thus exhibiting remarkable iodine capture capabilities through charge transfer, halogen bonding, and hydrophobic effects. The adsorbents show excellent stability and performance under complex and harsh conditions (pH 2–10) and can be easily regenerated, confirming their excellent reusability and potential for practical applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4081-y
The evolution of precision medicine has propelled multimodal imaging-guided phototheranostics to the forefront for precise tumor diagnosis and therapy. Low-temperature photothermal therapy (PTT) offers a promising approach for the treatment of melanoma due to its non-invasiveness and minimal damage to normal tissues. However, its efficacy is limited by cancer cell thermal tolerance. To address this, a new type of multifunctional energy disruptor (CAMeO-Q NPs) is developed featuring homologous targeting and mitochondria targeting, and synergistically enhancing low-temperature PTT in melanoma by reversing heat shock protein 90 (Hsp90)-mediated thermal tolerance and blocking mitochondrial adenosine triphosphate (ATP) biosynthesis. The multifunctional energy disruptor enables precise trimodal imaging (fluorescence imaging/FLI, photoacoustic imaging/PAI, and photothermal imaging/PTI) guidance for low-temperature PTT. Comprising a mitochondria-targeting photothermal agent and an Hsp90 inhibitor, CAMeO-Q NPs induce selective mitochondrial damage under 660 nm laser irradiation and downregulate cellular HSP expression by ATP inhibition and Hsp90 inhibitor. This multifunctional energy disruptor provides a novel strategy for enhancing multimodal imaging-guided low-temperature photothermal therapy through combined homologous targeting, mitochondria-targeting, and Hsp90 inhibition.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4008-2
Lung cancer, particularly non-small cell lung cancer (NSCLC), remains a leading cause of cancer-related mortality, with conventional therapies hampered by poor tumor specificity, low drug accumulation, and suboptimal efficacy. To address these challenges, we rationally designed a tumor-targeted, ferrocene-bearing, covalently immobilizable theranostic probe, dIR-CDF, for near-infrared (NIR) imaging-guided photodynamic-ferroptosis synergistic therapy. The probe exploits the overexpression of sulfenated proteins in the tumor microenvironment to specifically target integrin αvβ3-positive NSCLC cells and undergo covalent anchoring via the reaction between 1,3-cyclohexanedione and sulfenic acid, thereby enhancing tumor accumulation and retention. Under 808 nm irradiation, dIR-CDF generates singlet oxygen (1O2) for photodynamic therapy (PDT), while the sustained release of ferrocene catalyzes Fenton reactions to produce hydroxyl radicals (·OH), inducing ferroptosis. The synergistic action of PDT and ferroptosis amplifies lipid peroxidation and disrupts antioxidant defenses, leading to efficient suppression of NSCLC tumors in living mice. This work presents a universal and powerful theranostic platform for precise cancer diagnosis and treatment, with the covalent targeting strategy offering enhanced specificity and retention.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3958-8
Visual systems are the primary interface for humans to perceive the external environment. Mimicking the human eye, which integrates adjustable lenses with a curved retina, bio-inspired curved image sensors effectively mitigate field curvature and vignetting. To realize focus-tunable imaging, sensors must possess dynamic curvature while maintaining high sensitivity and mechanical stability. However, transitioning from rigid architectures to flexible devices often results in poor surface conformity through simple bending. Flexible sensors have explored intrinsic and structural designs for better flexibility and less stress concentration. Recent advances suggest that ultrathin devices with mesh-inspired designs offer a superior strategy, achieving seamless alignment with the curved surface without compromising optoelectronic performance. He et al. have developed a focus-tunable real-time curved imaging system inspired by the human visual system, based on an ultrathin perovskite curved image sensor with a hierarchical mesh architecture. They introduced an ultrathin image sensor with 5.4 μm thickness and soft interconnections, enabling it to be readily deformed into a hemispherical geometry. The ultrathin structure significantly reduces intrinsic mechanical behaviors, while interconnections effectively release twisting and stretching stress among pixels under various curvature conditions. As a result, the curved sensor array achieves a low detection limit of 10 nW cm−2, approaching the light sensitivity level of human photoreceptors. The focus-tunable imaging system integrates a curved image sensor with a shape-tunable convex lens, forming a conformal, skin-like architecture on a hemispherical surface. Finite element analysis revealed that when deformed to a curvature radius of 17.8 mm, the maximum strain on the Parylene C substrate reaches 5.72% and is primarily localized at pixel interconnections and edge regions. The curved image sensor achieves an overall thickness of approximately 5.4 μm and integrates a perovskite photodetector array comprising 127 pixels, enabling mechanically robust operation under pronounced curvature.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3911-7
The seamless integration of electronics with the human body is pivotal for next-generation human-machine interfaces (HMI) and personalized healthcare. Traditional high-density sensor arrays, while capable of capturing complex biomechanical data, impose significant power and comfort penalties. This study introduces the Generative EMG Network (GenENet), a framework that synergizes generative artificial intelligence with soft bioelectronics to reduce hardware complexity. By leveraging a 32-channel stretchable sensor array as a 'teacher' dataset, GenENet employs a masked autoencoder architecture to learn spatiotemporal correlations within high-density electromyography (EMG) data. The trained model enables a simplified 6-channel wearable band to replicate the performance of the full 32-channel array. The sensor device utilizes a polydimethylsiloxane (PDMS) substrate, liquid metal (EGaln) interconnects, and a conductive PEDOT:PSS hydrogel interface, achieving low skin-contact impedance and high signal-to-noise ratios under mechanical strain. This approach addresses the bottleneck of data throughput and power consumption in wearable HMIs, offering a path toward minimalist, personalized devices for applications such as sign language decoding and gait analysis. The findings underscore the potential of generative AI to transform wearable bioelectronics by shifting computational burden from hardware to software.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4126-0
Flexible X-ray detectors are constrained by the difficulty of producing semiconductor films that simultaneously exhibit uniform morphology, high crystallinity, and mechanical robustness. Here, we introduce a hydrogen-bond engineered supramolecular (HBES) strategy to overcome these limitations in supramolecular bismuth halide clusters (PDBiI5). By incorporating polyacrylic acid (PAA), a dynamic supramolecular network is formed that suppresses the coffee-ring effect during ultrasonic spray-coating via increased solution viscosity and controlled kinetic balance between solvent evaporation and solute diffusion. The HBES approach also modulates crystallization kinetics, extending crystal growth time from 23 to 41 s, yielding densely packed films with enhanced crystallinity and reduced defect states. These improvements lead to superior charge transport: a hole mobility of 2.16 cm2 V−1 s−1 and a mobility-lifetime product of 9.1 × 10−4 cm2 V−1. The resulting X-ray detectors achieve a record sensitivity of 19,009 μC Gyair−1 cm−2 and an ultralow detection limit of 3.35 nGyair s−1, with excellent operational and environmental stability. Leveraging the mechanical robustness from the supramolecular network, we demonstrate the first direct-type flexible X-ray imager, retaining 85% performance after 1000 bending cycles. This imager overcomes geometric distortion and vignetting, maintaining 85% edge photocurrent versus 58% for rigid detectors, enabling clear imaging of curved objects. This work establishes a versatile supramolecular engineering paradigm for high-performance flexible X-ray detection and imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4118-0
Polymer composite dielectrics are key materials for high-temperature film capacitors, yet their energy storage capability is severely constrained at elevated temperatures. Molecular fillers that simultaneously integrate deep-level trapping (high electron affinity, Ea), strong insulation (large bandgap, Eg), and high thermal stability are rarely available, posing a major challenge for improving high-temperature energy storage performance. To address this challenge, we screen and identify hexaazatriphenylene hexacarbonitrile (HAT-CN) as a promising candidate that fulfills the above critical requirements from numerous commercial organic molecules. When incorporated into a high glass transition temperature (Tg) polymer fluorene polyester (FPE), the resulting all-organic composite exhibits simultaneously suppressed high-temperature conduction loss and preserved mechanical robustness. Consequently, the optimized composite achieves record-high discharged energy densities of 7.31 J cm−3 at 150 °C and 6.14 J cm−3 at 200 °C (η≥90%) with a low cost and scalable process. This work demonstrates that the filler design based on synergistic key properties provides a potent pathway to break the longstanding high-temperature performance bottleneck in polymer dielectrics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4129-y
Therapeutic biosynthesis is a promising strategy for precision cancer therapy, yet achieving controlled synthesis of abiotic materials within tumors remains challenging. Here, we report a “dual lock-and-key” system for tumor-specific intracellular synthesis. The precursor, termed “dual-lock,” is activated by two endogenously overexpressed enzymes—azoreductase (AzoR) and nitroreductase (NTR)—acting as “dual keys” in target cancer cells. This activation triggers a condensation reaction that produces fibrous mesh covalent organic polymers (Fm-COPs) in situ. Synthesized Fm-COPs effectively disrupt the cytoskeleton, inhibiting cell migration and invasion while inducing apoptosis. In vivo studies demonstrate that this strategy achieves specific tumor enrichment and deep penetration, leading to significant tumor growth inhibition (tumor inhibition rate >70%) without systemic toxicity, as evidenced by stable body weights and normal histopathology. The dual enzyme-responsive mechanism ensures high selectivity, and the small-molecule precursors facilitate efficient tumor penetration. This work presents a next-generation approach for high-precision cancer therapy, offering a biocompatible and autonomous strategy for intracellular synthesis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4098-8
Fluorescence image-guided photodynamic therapy (PDT) enables real-time monitoring of photosensitizer biodistribution and metabolism for optimized treatment timing. However, its application remains limited by reliance on high-end imaging systems. To address this, we designed three novel small-molecule photosensitizers (TTNb, TTAn, TTPh) based on a 2-vinylbenzoic acid scaffold, functionalized at the 5-position with nitro, amino, or hydrogen groups. Replacing the nitro group with amino or hydrogen switched aggregation behavior from aggregation-induced emission (AIE) to aggregation-caused quenching (ACQ), accompanied by a red-to-green fluorescence shift and subcellular relocation from liposomes to lysosomes. These findings establish design principles for ratiometric nitroreductase probes and enable systematic comparison between AIE and ACQ photosensitizers. Among these, TTAn exhibited superior cellular uptake (2800 times higher than Ce6 in Eca-109 cells), specific lysosomal targeting, balanced reactive oxygen species (singlet oxygen/superoxide anion) generation, and intense fluorescence. Under white light irradiation, TTAn achieved an IC50 of 21 nM, surpassing Ce6 by 50-fold. Notably, TTAn produced strong fluorescence in mice tumors under both one- and two-photon excitation, detectable using conventional imaging tools (smartphones, DSLR cameras) or even visible to the naked eye, confirming outstanding tumor specificity. Leveraging these advantages, TTAn enabled successful image-guided two-photon PDT in Eca-109 tumor-bearing mice with a single treatment, demonstrating potent therapeutic efficacy and biosafety. This work provides a strategic blueprint for developing small-molecule theranostic agents that operate without complex fluorescence imaging systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4411-4
Wearable medical monitoring devices require conformal, long-term tissue integration, yet conventional rigid electronics fail to accommodate dynamic tissue deformation. This highlight examines the structural regulation logic of slidable van der Waals (vdW) layers as an instructive design paradigm for flexible bioelectronic materials. The approach leverages weak interlayer interactions to enable adaptive sliding, reducing interfacial stress and enhancing mechanical compliance. Key advances include spray-based fabrication, which offers scalability and cost-effectiveness for industrial translation. The strategy addresses bottlenecks in deep-tissue dynamic physiological monitoring, where existing interfaces suffer from mechanical mismatch and signal degradation. By tuning mechanical performance, enabling low-cost mass manufacturing, and integrating multi-hardware systems, this interface strategy promises to accelerate the transition from laboratory prototypes to clinical and consumer wearable devices. The highlight synthesizes recent literature, including a movable long-term implantable soft microfibre (Nature, 2025) and drawn-on-skin electronic tattoos (Sci Adv, 2026), to contextualize the vdW sliding approach. Quantitative metrics from these studies—such as mechanical compliance, operational stability, and fabrication throughput—are discussed to underscore industrial viability. The findings suggest that vdW layer sliding can be engineered to achieve fatigue resistance and conformal contact, critical for chronic implantation. This work provides a framework for designing next-generation bioelectronic interfaces, with implications for personalized medicine and remote health monitoring.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3631-1
Anion exchange membrane water electrolysis (AEMWE) offers cost and dynamic-response advantages over proton exchange membrane systems, yet commercial deployment is constrained by the alkaline stability of anion exchange membranes (AEMs) and the sluggish kinetics of non-precious metal catalysts. This work reports a series of poly(terphenyl-diphenylmethane piperidinium) (QPDPMTP) membranes synthesized with varied diphenylmethane (DPM) content. The alkyl chain of DPM induces pronounced microphase separation and elevates free volume fraction, yielding an OH− conductivity of 152 mS cm−1 at 80 °C for QPDPMTP-10. After 1032 h immersion in 6 M NaOH at 80 °C, the membrane retains 90.7% of its initial conductivity. An AEMWE cell integrating QPDPMTP-10 with a non-precious NiFeCo LDH/NiS/NF anode achieves 3.11 A cm−2 at 2 V in 1 M KOH at 80 °C and sustains 1 A cm−2 for 1800 h under gradient KOH concentration. These results establish a viable pathway for durable, low-cost AEMWE systems.