SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4464-9
Topological polarization textures have transitioned from theoretical predictions to experimental observations over two decades, yet their stabilization has remained largely confined to low-dimensional architectures where geometric confinement balances depolarization, strain, and gradient energies. Extending these textures into bulk ferroelectrics and quantitatively linking them to macroscopic electromechanical properties constitutes a persistent challenge. Wu et al. address this by engineering vortex and antivortex domains in bulk rhombohedral 0.7Pb(Mg1/3Nb2/3)O3-0.3PbTiO3 (PMN-30PT) crystals. Phase-field simulations reveal that increasing vortex core density from 6 to 27 μm⁻² enhances the dielectric constant (ε33/ε0) and piezoelectric coefficient (d33) by approximately 3.5-fold and 3.4-fold, respectively, correlating with increased polarization curl. Experimentally, a mechanically assisted direct-current poling (MDCP) strategy elevates vortex core density from 0.01 to 21 μm⁻², boosting d33 from 1380 to 1820 pC·N⁻¹ and ε33/ε0 from 4,630 to 6,230. This mechanically driven approach enables controllable manipulation of topological domain architectures in bulk crystals without nanoscale confinement, offering a scalable route for functional optimization. The work establishes bulk ferroelectrics as a platform for topology-mediated electromechanical design, introducing an additional degree of freedom for enhancing piezoelectric performance in three-dimensional crystals.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4418-7
Glioblastoma (GBM) remains the most lethal primary brain tumor, with the blood-brain barrier (BBB) severely restricting effective treatment options. Immunotherapy has achieved remarkable success in cancers such as lung cancer and melanoma, yet its efficacy in GBM is constrained by the immunosuppressive tumor microenvironment and a paucity of tumor-infiltrating T cells. This study developed a biomimetic nanocomposite for the co-delivery of an immunogenic cell death (ICD) inducer and an indoleamine 2,3-dioxygenase 1 (IDO-1) inhibitor to overcome these challenges. Paclitaxel-derived carbon dots (PCDs), which induce ICD in tumor cells and promote the recruitment and activation of immune cells, were synthesized and assembled with Indoximod (an IDO-1 inhibitor) to form a nanocomposite (P-In). A biomimetic coating was subsequently applied to create M@P-In. This coating significantly enhanced BBB penetration and tumor cell uptake. The M@P-In nanocomposite efficiently induced ICD in tumor cells and inhibited IDO-1 activity via the released Indoximod, thereby reversing T-cell suppression and activating antitumor immune responses. Consequently, M@P-In demonstrated potent antitumor efficacy against glioblastoma in vivo with minimal systemic toxicity. This work presents a novel and promising strategy for immunochemotherapy against GBM by co-delivering a carbon dot-based ICD inducer and an IDO-1 inhibitor to the tumor site.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4358-y
Oxygen electrocatalysis underpins the viability of proton-exchange-membrane water electrolyzers and rechargeable Zn–air batteries, yet commercial deployment remains constrained by the sluggish kinetics of the oxygen evolution reaction (OER) and oxygen reduction reaction (ORR), which impose overpotentials exceeding 300 mV and accelerate catalyst degradation. This review, submitted to SCIENCE CHINA Materials (Manuscript ID SCMs-2026-1384.R1), synthesizes recent advances in rational catalyst design guided by the direct observation and theoretical treatment of reaction intermediates. The authors compile evidence from in situ characterization and computational modeling to establish that intermediate binding energies—particularly *OOH, *O, and *OH on Ru, Ir, Co, and Fe–N–C active sites—serve as predictive descriptors for activity and stability. Cited works demonstrate that 4f-modified Ru–O polarity, spin-balanced Janus Ir–Co magnetic atoms, and aligned d-orbital energy levels in dual-atom sites can shift rate-determining steps and lower activation barriers. The review further examines interfacial microenvironment engineering via anion adsorption, ligand functionalization, and S,N co-doped carbon confinement, which modulate local pH, water orientation, and mass transport. Emphasis is placed on dual-site mechanisms, including FeN6–CoN4 and Co-substituted Ni coordination polymers, where synergistic strong–weak adsorption coupling alters ORR pathways from adsorbate evolution to dissociation. The manuscript provides a critical assessment of descriptor reliability, noting that intermediate binding alone cannot capture dynamic reconstruction, electrolyte effects, or long-term operational stability. By integrating in situ spectroscopy with descriptor-based design, the review offers a framework for translating mechanistic insight into durable, cost-effective oxygen electrocatalysts for industrial electrolysis and metal–air batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4498-7
Two-dimensional porphyrin-based hypercrosslinked polymers (TPP-HCPs) were synthesized via room-temperature interfacial polymerization using 5,10,15,20-tetraphenylporphyrin and 1,3,5-trioxane. The resulting TPP-HCPs exhibited a BET surface area of 548 m2 g-1 and a CO2 uptake of 7.97 wt% at 1 bar and 298 K. CuO/TPP-HCPs nanospheres were fabricated by thermal conversion of Cu(NO3)2·3H2O in DMF at 135 °C, using TPP-HCPs as dynamic templates. This in-situ strategy generated CuO nanoparticles within the conjugated porous matrix, facilitating electron transfer and enhancing CO2 access to catalytic centers. In CO2 electroreduction, the composite achieved a total gas Faradaic efficiency exceeding 90% at ~500 mA cm-2 (-1.4 V vs. RHE), with 40.9% for C2H4, 8.2% for CH4, 31.9% for CO, and 12.3% for H2. The catalyst maintained stability over 24 h in an H-cell. These results demonstrate that 2D conjugated polymer-templated catalysts can sustain high-rate CO2 conversion to value-added products, offering a viable route for industrial CO2 utilization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4321-x
Poly(ethylene oxide) (PEO)-based solid polymer electrolytes are leading candidates for solid-state lithium metal batteries due to their flexibility, processability, and interfacial compliance. However, the strong crystallization tendency of PEO and limited lithium salt dissociation result in low ionic conductivity and low Li+ transference number, exacerbating concentration polarization and interfacial instability. Introducing metal-organic framework (MOF) fillers into PEO matrices has emerged as an effective route to regulate polymer-chain packing and promote salt dissociation via Lewis acid-base interactions. Yet, most studies focus on cubic ZIF-8, whose saturated Zn coordination environment limits intrinsic Lewis acidity and restricts its ability to immobilize TFSI- anions. Simultaneously, simple physical blending often leaves discontinuous interfacial transport regions in composite electrolytes, so improved salt dissociation does not automatically translate into fast Li+ transport. Here we report a PEO-based composite polymer electrolyte, denoted as PZS, that couples monoclinic ZIF-8 (M-ZIF-8) nanosheets with a thin SiO2 layer. The design combines two complementary functions: the under-coordinated Zn sites in M-ZIF-8 provide strong Lewis acid centers to adsorb TFSI- and promote LiTFSI dissociation, while the hydroxyl-rich SiO2 shell improves compatibility with the PEO matrix and helps construct continuous interfacial Li+ transport pathways. Benefiting from this synergy, the optimized PZS electrolyte delivers an ionic conductivity of 8.3 × 10-4 S cm-1 and a Li+ transference number of 0.57 at 60 ℃, together with an electrochemical stability window of 5.2 V. Li||Li symmetric cells remain stable for over 1200 h at 0.1 mA cm-2, and LFP||Li full cells retain 80% of their capacity after 400 cycles at 0.5 C.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4426-y
Biomedical Mg alloys are candidate biodegradable metals for orthopedic and cardiovascular implants, yet their in vivo service life is governed by coupled mechanical-chemical attack that accelerates loss of mechanical integrity. This review consolidates recent advances in stress-assisted degradation of Mg alloys under physiological conditions, focusing on stress corrosion cracking (SCC), flow-induced corrosion, and corrosion fatigue. Biomechanical-chemical coupling test methods are assessed for their capacity to reproduce physiological loading, fluid shear, and electrolyte chemistry. Mechanistic pathways are analyzed, including anodic dissolution, hydrogen-induced cracking, passivation film rupture, and flow-induced shear stress. Modification strategies for enhancing resistance to stress-assisted degradation are categorized into alloying design, microstructure regulation, and surface treatments. The review further evaluates computer-aided predictive models and multi-physics coupling frameworks that link pit-to-crack transitions, phase-field damage localization, and mechano-chemical peridynamics. Empirical data from the cited literature demonstrate that SCC and corrosion fatigue in chloride-containing media reduce fatigue strength by 40–70% relative to air, while flow-induced shear stresses above approximately 1 Pa disrupt protective films and elevate degradation rates. These findings establish quantitative benchmarks for alloy design and surface engineering. The review concludes that integrating multi-physics modeling with physiologically relevant testing is essential for predicting implant service stability and accelerating clinical translation of high-performance biomedical Mg alloys.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4487-1
Direct seawater electrolysis offers a cost-effective route to clean hydrogen, but the competitive chlorine evolution reaction (CER) and electrode corrosion impede practical deployment. A NiIr(OH)6 perovskite hydroxide catalyst was synthesized via one-step co-precipitation. In alkaline seawater, it requires only 330 mV overpotential to reach 100 mA cm-2 and sustains 190 h in multi-current step testing. In situ Raman spectroscopy shows that Ir species promote the formation of active NiOOH phases, accelerating oxygen evolution reaction (OER) kinetics. Density functional theory calculations reveal that Ir doping modulates the electronic structure of Ni and Ir sites, strengthening OH adsorption (-2.09 eV) and suppressing Cl- adsorption (-1.38 eV), thereby enhancing OER selectivity. An overall seawater electrolyzer with NiIr(OH)6 || Pt/C delivers 100 mA cm-2 at 1.63 V and operates stably for over 100 h. This work provides a rational design strategy for high-efficiency, corrosion-resistant electrocatalysts for seawater electrolysis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4240-7
The electrocatalytic ammonia oxidation reaction (AOR) is pivotal for sustainable energy conversion and storage, enabling direct ammonia fuel cells (DAFCs), ammonia electrolysis, and solid oxide fuel cells. This review critically examines recent advances in AOR catalysis, emphasizing active-site regulation, interfacial engineering, and device-oriented catalyst development. For noble-metal catalysts, optimizing adsorption and dehydrogenation of NHx intermediates while mitigating poisoning is essential for sustained activity. Non-noble-metal systems, particularly Ni-based catalysts, require precise control of reconstructed working-state phases such as NiOOH-like species to balance activity and selectivity. Interfacial engineering, including heterointerfaces, defect structures, and doped coordination environments, strongly influences the competition between AOR and oxygen evolution reaction (OER), as well as product branching toward N2 or oxygenated nitrogen species. The review underscores that catalyst optimization now extends beyond bulk composition to the precise regulation of the interfacial reaction microenvironment. Furthermore, practical device operation is governed by membrane/electrolyte compatibility, mass transport, ammonia crossover, thermal management, and long-term durability. Bridging fundamental catalyst studies with deployable ammonia energy technologies requires coordinated optimization from active materials to electrode architectures and full-device systems. This review provides a comprehensive framework for designing next-generation AOR catalysts and accelerating their integration into industrial energy systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4350-4
Flexible wearable sensors have transformed motion tracking, soft robotics, and human-machine interfaces by enabling precise movement detection and adaptability to curved surfaces. However, conventional composite sensors often face challenges such as limited sensitivity, detection range, linearity, and durability. In this study, we propose a stretchable auxetic sensing textile with a negative Poisson’s ratio (NPR) structure, incorporating reduced graphene oxide (rGO) and carbon nanotubes (CNT) by micro-crack engineering to enhance its mechanical durability and sensing performance. Integrating macro-scale NPR with micro-scale wrinkles, this innovative design achieves a high sensitivity of 11.2 within a wide detection range (0-100%), a more linear sensing range with an R2 value of 0.998, an ultra-low detection limit of 0.5%, and exceptional durability, outperforming conventional wearable sensors. Additionally, the textile sensor boasts excellent moisture permeability (32.7 g m⁻² h⁻¹) and a remarkable NPR value of -0.25, ensuring comfort and adaptability for various wearable applications. Integrated with deep learning algorithms, the auxetic sensing textile demonstrates 98% accuracy in recognizing soft robotic movements at various bending angles. It is capable of capturing both small-scale physiological signals, such as electrocardiograms, and large-scale movements, offering significant freedom of movement and adaptability to complex surfaces.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4381-5
Bismuth telluride (Bi2Te3)-based alloys remain the benchmark for low-temperature thermoelectric applications, yet their conversion efficiency is limited by the trade-off between electrical and thermal transport. This study introduces a pseudo grain boundary engineering strategy to simultaneously enhance the average figure of merit (ZT) in p-type (Bi,Sb)2Te3 (BST) materials. By incorporating Ag-based compounds, the carrier concentration is optimized via substitution of Ag+ ions, while the introduction of secondary phases at grain boundaries effectively suppresses lattice thermal conductivity. The approach yields a peak ZT of 1.35 at 393 K and an average ZT of 1.25 across 303–483 K, representing a significant improvement over pristine BST. Compared to prior reports, this work achieves superior average ZT while maintaining high electrical conductivity, addressing the longstanding bottleneck of thermal conductivity reduction without compromising carrier mobility. The findings underscore the efficacy of pseudo grain boundary engineering in advancing Bi2Te3-based thermoelectrics for solid-state cooling and power generation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4212-x
Idiopathic pulmonary fibrosis (IPF) is a lethal interstitial lung disease with limited therapeutic options. Current treatments, such as nintedanib and pirfenidone, target downstream fibrosis but fail to address the upstream drivers, including persistent alveolar epithelial injury and abnormal repair. This study presents an inhalable, reactive oxygen species (ROS)-responsive liposomal system (SAB/GC-1@Lip-cRGD) that co-delivers the antioxidant salvianolic acid B (SAB) and the thyroid hormone receptor β (TRβ) agonist Sobetirome (GC-1). The liposomes are surface-modified with cRGD peptides for targeted delivery to fibrotic lesions and possess a negative surface charge to enhance mucus penetration. In the high-ROS fibrotic microenvironment, the liposomes destabilize, releasing SAB and GC-1. SAB scavenges ROS to remodel the fibrotic niche, while GC-1 reactivates TRβ signaling, driving the differentiation of stalled Krt8+ transitional epithelial cells into functional alveolar type I (AT1) cells. In a mouse model of pulmonary fibrosis, SAB/GC-1@Lip-cRGD significantly reduced pro-inflammatory cytokines (TNF-α, IL-1β, IL-6) and TGF-β1 in bronchoalveolar lavage fluid and lung homogenates. The proportion of CD206+ M2 macrophages decreased from 27.4% in the model group to 6.2% after treatment, indicating potent anti-inflammatory and anti-fibrotic effects. This synergistic strategy of microenvironment remodeling and epithelial regeneration achieved robust collagen depletion, restoration of alveolar integrity, and recovery of pulmonary function, outperforming single-drug or non-targeted formulations. The work provides a generalized paradigm for integrating microenvironment regulation with regenerative repair in pulmonary diseases.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4235-6
Fluorite-structured oxides (HfO2, ZrO2) are promising for resistive random-access memory (RRAM) due to their scalability and tunable properties. However, achieving high resistive switching on/off ratios remains challenging. Here, we report a collaborative strategy combining Hf/Zr ratio optimization and Lu3+ doping to regulate band structure and oxygen vacancy concentration in Hf0.4Zr0.6O2 (LHZO) thin films. The resulting LHZO devices exhibit a resistive switching ratio of 8.4 × 10^4, two orders of magnitude higher than that of ZrO2 (1.2 × 10^3). Electrical characterization and synchrotron radiation photoemission spectroscopy reveal that Lu doping widens the bandgap to 4.95 eV, downshifts the valence band, and introduces defect states, collectively suppressing p-type conductivity and reducing off-state leakage current. Simultaneously, Lu3+ doping enriches oxygen vacancies, stabilizing ohmic conductive filaments in the on-state. This co-optimization of band structure and oxygen vacancies effectively enhances insulating properties in the high-resistance state and ohmic conductivity in the low-resistance state, leading to superior resistive switching performance with robust retention (>10^4 s). Our findings establish a fundamental strategy for tailoring electronic properties of doped HfZrO2 thin films toward high-performance RRAM applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4176-y
Three-photon microscopy (3PM) in the near-infrared-III (NIR-III) window (1600–1840 nm) enables high-resolution visualization of cerebral vasculature in vivo, but its imaging depth and quality are limited by the performance of fluorescent probes. Here, we report a probe optimization strategy transitioning from mirror symmetry to centrosymmetry, yielding a highly symmetric aggregation-induced emission (AIE) molecule, T4PQ. The centrosymmetric structure aligns donor-acceptor units, promoting uniform electron cloud delocalization and directional charge transfer, which enhances exciton formation and suppresses non-radiative decay, thereby increasing fluorescence quantum yield. This symmetry also boosts the three-photon absorption cross-section by enhancing electron delocalization and transition dipole moment, enabling stronger nonlinear optical responses under long-wavelength excitation. T4PQ nanoparticles (T4PQ NPs) exhibit an enhanced three-photon absorption cross-section, high fluorescence quantum yield, and excellent photostability. In murine models, T4PQ NPs achieved three-dimensional cerebrovascular imaging at a depth of 1785 μm and real-time hemodynamic observation in microvessels at 1006 μm depth, with good biocompatibility. These results validate the advantage of centrosymmetric molecular design for deep-brain imaging probes, offering a high-performance tool for neurovascular research.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4112-6
Radiostrontium remediation is crucial for ecological protection and sustainable development of nuclear energy. However, efficient removal of 90Sr from complex radioactive liquid waste, especially under acidic conditions, remains challenging due to material instability and intense proton competition. Herein, the rapid and highly selective capture of Sr2+ in neutral and even acidic solutions has been achieved by a layered potassium phosphatoantimonate KSbP2O8 with excellent radiation and thermal stability. Under neutral conditions, it possesses high maximum adsorption capacity (qmSr = 110.25 mg g−1), rapid adsorption kinetics (the removal rate (RSr) of 91.54% within 30 min), and excellent selectivity for Sr2+, and facile regeneration. Particularly, even under acidic conditions (pH 2.0), KSbP2O8 still maintains excellent Sr2+ removal capacity (qmSr = 79.38 mg g−1), fast kinetics, and high selectivity. A mechanism study by multiple characterizations reveals that the efficient Sr2+ removal of KSbP2O8 mainly stems from ion exchange between Sr2+ and interlayer K+ in KSbP2O8, which is attributed to the synergy between the Sb5+-induced Brønsted acidity and the high charge density of the anionic framework. This study demonstrates the exceptional capability of phosphatoantimonates to selectively capture Sr2+ under acidic conditions, highlighting the potential of phosphatoantimonates as effective scavengers for radiostrontium remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4232-1
Polyanionic cathode materials are widely considered as potential cathode materials for sodium-ion batteries due to their strong three-dimensional framework and intrinsic thermal safety. Nevertheless, the limitation of the specific capacity and energy density hindered their application, which can be ascribed to the common reliance of single-electron redox reaction of the transition metal. By realizing the reversible double redox reaction of vanadium-based and manganese-based polyanion cathodes, researchers have successfully opened up a new way to break through the long-term performance limitations. Recent studies disclose that vanadium and manganese-based polyanionic cathodes exhibit the possibility of realizing a reversible double-redox reaction, which opened up new avenues to overcome the capacity dilemma. However, many fundamental issues remain unclear, including insufficient structural stability at high operating voltages, irreversible structural evolution induced by sodium extraction, sluggish electronic and ionic transport kinetics, and Jahn–Teller distortion. Therefore, it is imperative to summarize recent work in order to clarify the pathway for future investigation. In this review, the key challenges associated with the activation of the double-redox reaction are outlined, followed by the realization and regulation of the double-redox reaction in polyanionic cathode materials. A systematic summary of recent studies is performed for both vanadium and manganese-based compounds, which could contribute to the fundamental understanding of the double-redox reaction mechanism. Combined with the modification strategy and future perspective, this review provides insights into the rational design of polyanionic cathodes with a reversible double-redox reaction. It also offers insights into the development of high-energy-density cathode materials for next-generation sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4337-2
Silica aerogels are recognized as leading super-insulating materials due to their ultralow thermal conductivity, yet their intrinsic brittleness and poor processability restrict practical deployment in complex industrial and extreme environments. This study introduces a macro-scale 'stiff–soft' synergistic strategy, combining a macroscopically processable, soft-and-tough framework as the load-bearing component with hard-and-brittle polymethylsilsesquioxane (PMSQ) aerogels as the insulating component. A pressure-driven assembly process enables viscosity-tunable PMSQ gel inks to be controllably infused into various hollow frameworks, including honeycomb panels, wheat straws, and hollow fibers. Guided by a modified Hagen–Poiseuille model, ink viscosity is precisely matched to the geometric parameters of the hollow structures. The resulting composites achieve compressive strength of 2.5 MPa, flexural strength of 6.25 MPa, and tensile strength of 40 MPa, while maintaining excellent thermal insulation. This versatile and scalable approach offers a new design paradigm for mechanically adaptive silica aerogel composites in thermal management applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4258-0
High-entropy noble-metal-based catalysts (HENCs) have emerged as a frontier in electrocatalysis, leveraging the synergistic effects of high-entropy alloys and noble metals to achieve exceptional atomic utilization, tunable electronic structures, and vast compositional space. Their anisotropic architectures confer superior dissolution resistance, rapid electron/mass transfer, and abundant active sites. This review systematically categorizes advanced structural regulations—grain boundary engineering, single-atom alloys, intermetallic compounds, amorphous structures, and core@shell configurations—and evaluates their impact on electrocatalytic performance. By modulating surface electronic states and lattice strain, these strategies optimize reaction kinetics and durability. Notable applications include oxygen reduction (ORR), oxygen evolution (OER), hydrogen evolution (HER), and CO2 reduction (CO2RR). Despite progress, challenges persist in scalable synthesis, mechanistic understanding, and long-term stability. This review underscores the potential of HENCs to bridge laboratory innovation and industrial deployment, providing a roadmap for future catalyst design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3582-9
Perovskite quantum dots (PQDs) hold great potential for brain-like neuromorphic computing. However, the development of PQDs-based synaptic devices is hindered by interfacial defects and limited stability. Here, we demonstrate a high-performance Cs2AgBiBr6 QDs/organic single crystal heterojunction synaptic device, fabricated via a novel space-confined vertical growth technique combined with a polymer-free transfer process. Vertically grown organic single crystals enable superior carrier mobility and facilitate the formation of low-defect interfaces with PQDs. The heterojunction exhibits remarkable photosensitivity (7.22 × 10^5 at 425 nm) and detectivity (2.15 × 10^15 Jones), owing to the strong optical absorption of PQDs coupled with the superior charge transport characteristics of organic single crystals. Notably, the device achieves dual-functional light adaptation, emulating synaptic behaviour under blue light while exhibiting photo-switching under green/red light. This unique capability enables smart blue-light hazard protection. This work not only provides a versatile platform for high-performance PQDs-based synaptic devices but also advances the development of brain-inspired neuromorphic systems for next-generation computing and intelligent sensing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3771-9
High-entropy carbonitride ultra-high temperature ceramics (HECN-UHTCs) typically require high densification temperatures, leading to grain coarsening and degraded mechanical properties. This study introduces CrSi2 as a sintering additive for (Ti, Zr, Hf, Nb, Ta)(C, N), effectively reducing the densification temperature by 200 °C. During sintering, interdiffusion and cation exchange result in the formation of an orthorhombic (Ti, Zr, Nb)2Cr4Si5 phase within the ceramic matrix. The resulting dual-phase ceramic exhibits a hardness of 24.65 ± 0.23 GPa and a fracture toughness of 6.03 ± 0.48 MPa m1/2, significantly surpassing most reported HECN-UHTCs. Enhanced mechanical properties are attributed to crack deflection, increased localized lattice strain, and Cr grain boundary segregation. This liquid phase-assisted low-temperature sintering strategy offers a promising pathway for densifying other ultra-high temperature ceramics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3538-6
The understanding of anion transporting behaviors under sub-nanoconfined regimes can guide the design of high-performance anion selective membranes (ASMs), yet it is little known. Here, we build membrane channels that combine physical rigidity with chemical affinity to anions simply through bridging graphene oxide nanosheets with charged linkers. We observe that the rigidly confined interaction imposed by channels to anions can reconfigure hydration shells in varying degrees for different anions via compensating for hydration-induced energy barriers and differentiating their rearrangement behaviors. During the configuration evolution, water molecules within hydration shells would rotate and simultaneously change their distance from the ion center. Based on the big discrepancy in configuration evolution, these membranes can realize ultrahigh selectivity of, for example, 125 for Cl−/SO4^2− and surpass the performance upper bound concerning Cl−/SO4^2− separation by other membranes. The knowledge of the configuration change of hydration shells during the dehydration process will be key to designing next-generation ASMs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3698-5
The oxygen evolution reaction (OER) is a critical bottleneck in next-generation sustainable energy systems due to its sluggish kinetics. Developing cost-effective, high-efficiency electrocatalysts requires understanding the dynamic structural evolution at electrode-electrolyte interfaces under operating conditions. In situ techniques are invaluable for identifying active centers and monitoring key intermediates. This review comprehensively summarizes recent advances in cutting-edge in situ methods for characterizing OER electrocatalyst structure evolution. It provides a brief overview of active motifs and robust structures using multiple in situ correlative techniques, establishing essential structure-performance relationships and updating mechanistic understanding at atomic scale under realistic conditions. Key challenges and perspectives are highlighted to promote rational design of promising electrocatalysts for efficient oxygen-associated electrocatalysis and electrosynthesis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3672-8
Pore-tuning engineering is an effective strategy for designing catalysts for energy storage and conversion. Here, we report a rhombic dodecahedral iron and nitrogen co-doped carbon (Fe-N-C) material with hierarchical micro-mesoporous structures, synthesized using mesoporous silica as both pore template and iron source. The resulting catalyst (m-Fe/NC) exhibits significantly enhanced oxygen reduction reaction (ORR) activity, with half-wave potentials of 0.81 V and 0.88 V in acidic and alkaline media, respectively. When employed as a cathode in zinc-air batteries, m-Fe/NC delivers a superior specific capacity of 815 mAh g_Zn^-1 and a stable cell voltage of 1.31 V at a current density of 10 mA cm^-2. Advanced characterization and theoretical calculations reveal that the mesoporous structure not only increases active site exposure but also induces a curvature-induced strain effect on concave surfaces, which enhances intrinsic activity. This work provides insights for developing innovative nanoporous electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3759-7
The inherent strength-ductility trade-off in materials science poses a significant challenge for structural applications. In composites, rational regulation of reinforcement structure and distribution can enhance both strength and ductility. Typical structures such as network, layered, and columnar have proven effective, yet issues like narrow size ranges, uneven distribution, and weak interfacial bonding limit performance. Here, we present a bioinspired multi-scale heterogeneous layered composite (MHLC) that achieves an optimal balance between strength and ductility. This heterogeneous layered structure comprises alternately stacked Cu-Ti layers and GNPs/Cu layers. The Cu-Ti layer contains uniformly distributed plate-like β-Cu4Ti intermetallic compounds, while the GNPs/Cu layer contains layered graphene nanoplatelets (GNPs). The size, distribution, and shape of reinforcements can be adjusted through heat treatment and cold rolling, enabling a balance between strength and ductility. Molecular dynamics simulation and finite element simulation were conducted to investigate the structural evolution of β-Cu4Ti and the influence of reinforcements on tensile properties, respectively. Results show that under tensile deformation, high-strain regions in the Cu-Ti layer are more numerous than in the GNPs/Cu layer. At an applied strain of 7.96%, fracture and deformation of reinforcements occur; at 23.98%, voids appear and develop into cracks. Cracks propagate along high-strain paths, forming a zigzag fracture pattern at the interface, indicating high interfacial bonding strength. The bending deformation of β-Cu4Ti suggests it possesses high hardness, strength, and excellent toughness. Our results provide important references for exploring multi-scale heterogeneous layered structures in enhancing strength and ductility of composites.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3625-3
Zirconia (ZrO2)-based fluorite ferroelectric materials are promising for nonvolatile memory and logic devices due to their CMOS compatibility and cost advantages over hafnium oxide (HfO2). However, the metastable nature of the ferroelectric orthorhombic phase (o-phase) hinders practical application. Here, we report the strain-mediated stabilization of the ferroelectric o-phase in ZrO2 thin films grown on niobium-doped strontium titanate (NSTO) substrates with different crystallographic orientations via chemical solution deposition. Systematic structural and ferroelectric characterization, combined with simulation, reveals that substrate orientation controls in-plane tensile strain, selectively promoting epitaxial growth of the o-phase. The ZrO2 film on NSTO(110) exhibits the highest o-phase content, achieving a remanent polarization (2Pr) of 92.64 μC/cm², which remains as high as 88.54 μC/cm² after resistive-capacitive (RC) delay calibration. The device shows endurance of approximately 10^7 cycles with favorable fatigue characteristics. X-ray absorption spectroscopy (XAS) further indicates distortion of Zr-O tetrahedra, providing microscopic insight into the ferroelectricity. This work presents a novel strategy for property tuning of ZrO2 films and supports their application in storage and logic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3653-2
Designing photosensitizers with efficient intersystem crossing (ISC) and long-lived triplet excited states is critical for photodynamic therapy (PDT). However, conventional molecular design principles often rely on heavy-atom effects or specific donor-acceptor architectures, limiting generality. Here, we report a facile and rational strategy to convert intrinsically non-photosensitizing fluorophores into effective reactive oxygen species (ROS) generators by introducing guanidinium substituents. The modified photosensitizers exhibit prolonged triplet excited state lifetimes and considerable ROS production, in stark contrast to unmodified fluorophores which show intense fluorescence and negligible ROS generation. Electron paramagnetic resonance spectroscopy and high-resolution mass spectrometry confirm the formation of stable nitrogen-centered radical cations on the guanidinium moiety, stabilized by p-π conjugation. Mechanistic studies indicate that these radicals promote ISC and prolong triplet state lifetimes. In vitro and in vivo experiments demonstrate that guanidinium-modified photosensitizers induce immunogenic cell death (ICD) and elicit potent anti-tumor immunity. This work provides a universal and facile strategy for designing organic photosensitizers through stable radical cation-containing building blocks, expanding the scope of PDT agents.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3657-9
Perovskite/silicon tandem solar cells (TSCs) have achieved power conversion efficiencies (PCE) up to 34.9%, surpassing the Shockley-Queisser limit of single-junction devices. The interconnection layer (ICL) critically bridges top and bottom subcells, enabling charge carrier recombination. Conventional indium oxide (In2O3)-based TCOs suffer from high-energy ion bombardment during sputtering, damaging amorphous silicon subcells and reducing open-circuit voltage (VOC) and fill factor (FF). Additionally, indium scarcity and cost necessitate indium-free alternatives. Here, we introduce a highly degenerate indium-free samarium-doped cadmium oxide (CdO:Sm) TCO as the ICL for perovskite/SHJ TSCs, deposited via low-damage reactive plasma deposition (RPD). The ultrathin CdO:Sm film (~3 nm) exhibits average transmittance of 85% (400–1200 nm) and 90% (800–1200 nm), enabling efficient near-infrared absorption in the bottom subcell. High doping concentration and mobility ensure excellent electrical conductivity. The low work function (4.04 eV) of CdO:Sm facilitates carrier tunneling and efficient recombination. Devices employing CdO:Sm ICL achieved approximately 1% higher efficiency compared to those with indium-based TCO ICLs. Detailed characterization including contact resistivity (1.68 mΩ cm2), conductive atomic force microscopy, Kelvin probe force microscopy, and photoluminescence quenching confirm enhanced carrier transport and extraction. This work demonstrates a viable indium-free ICL for high-efficiency perovskite/SHJ TSCs, addressing both performance and sustainability challenges.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61068-2
The poor interface contact between bismuth (Bi) nanoparticles and reduced graphene oxide (rGO) impedes ion/electron transfer in lithium-ion battery anodes. We report an innovative fabrication of ultrafine Bi nanocrystals chemically bonded to rGO (Bi-rGO) via liquid-phase pulsed laser irradiation followed by solvothermal reaction with graphene oxide. Metastable Bi nanocrystals synthesized by laser (5.5 nm) undergo lattice restructuring and shrink to a record-small size of 2 nm during solvothermal combination, the smallest reported for Bi/C composites. The Bi nanocrystals are uniformly anchored onto rGO nanosheets via strong Bi–O–C bonds, which suppress particle aggregation, establish efficient ion/electron transport channels, and alleviate volume expansion during lithiation. The Bi-rGO-2 anode, comprising 2 nm Bi nanocrystals, delivers an exceptional reversible capacity of 586.7 mAh g−1 over 500 cycles at 100 mA g−1, nearly doubling that of a Bulk Bi/rGO composite anode (318 mAh g−1). Theoretical calculations confirm higher binding energy between Bi and rGO at smaller particle sizes, while kinetic analysis reveals accelerated Li+ diffusion. This work provides a scalable route to high-performance alloy anodes through metastable nanocrystal engineering and covalent interface coupling.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3503-9
This correction addresses an image misuse in the original publication (Sci China Mater, 2025, 68(6): 2095, DOI: 10.1007/s40843-025-3311-6). Specifically, a fluorescent image in Fig. 4d, depicting live/dead cells after treatment with MPDA@TMZ without laser irradiation, was erroneously presented. The corrected Fig. 4 is provided, and the authors confirm that the results and conclusions of the original paper remain unaffected. The correction ensures the integrity of the reported data, particularly the cell viability and apoptosis assays. The study focuses on mesoporous bowl-shaped polydopamine (MPDA) nanoparticles co-loaded with temozolomide (TMZ) and indocyanine green (ICG) for synergistic glioblastoma therapy. The corrected figure includes CLSM images of G422 cells after incubation with various formulations (ICG, sPDA@ICG, mPDA@ICG, MPDA@ICG), cell viability curves, quantitative fluorescence intensity, live/dead staining, and apoptosis quantification. Statistical significance is denoted as ****p < 0.01. The correction maintains the scientific validity of the findings, which demonstrate the potential of MPDA-based nanoplatforms for combined chemo-photothermal therapy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3807-8
Electrocatalytic co-reduction of CO2 and nitrate offers a sustainable route for urea synthesis, valorizing nitrogenous waste and CO2. However, achieving high-performance urea electrosynthesis under ambient conditions remains challenging due to the need for simultaneous activation of CO2 and efficient H2O dissociation to supply active *H for *NOx hydrogenation, ultimately forming key C- and N-containing intermediates for C–N coupling. Here, we report a bifunctional Pd-single-atom-modified Cu (Pd1Cu) nanorod catalyst that synergistically promotes adsorption and stepwise activation of CO2 and H2O, steering the reaction pathway toward selective urea synthesis. Integrating experimental evidence, in situ spectroscopy, and computational analyses, we disclose that atomically dispersed Pd sites kinetically favor co-generation of *CO and *NH2 via H2O dissociation-driven proton transfer, forming an optimal intermediate balance. The dual metal active sites enhance C–N coupling via combined electronic and geometric effects, substantially lowering the reaction energy barrier and improving selectivity. This work provides a rational design strategy for advanced multifunctional catalysts for urea electrosynthesis, contributing to carbon neutrality and waste nitrogen valorization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3838-5
Air-permeable and ultrathin conductive electrodes are essential for next-generation soft electronics, including breathable wearables, on-skin devices, and bio-integrated electronics. However, conventional metallization strategies, such as sputtering and ink-printing, often suffer from severe vertical charge leakage due to the porous and ultrathin characteristics of nanofibrous networks, leading to device short-circuiting, operational failure, and limited vertical integration. Here, we present a solvent-selective dissolution-assisted transfer printing strategy to achieve surface-confined metallization of ultrathin, lightweight, and gas-permeable nanofibrous networks, enabling lateral conductivity while maintaining vertical insulation. This transfer printing process facilitates not only the rapid formation of conductive patterns on the surface of nanofibrous networks but also mechanical reinforcement through solvent evaporation-induced interlocked fiber-fiber welding. Meanwhile, the strategy preserves the high permeability of the nanofibrous networks and imparts a unique combination of surface conductivity (2 Ω cm) and vertical insulativity (10^11 Ω cm). The resulting anisotropic conductive networks enable low-voltage wearable heaters, high-sensitive pressure sensors, and ultralight temperature sensors. A pressure-temperature dual-modal sensing patch is further fabricated for intelligent grasping classification. The proposed surface-confined metallization strategy enables rapid fabrication of an anisotropic conductive network as a building block to construct air-permeable, ultrathin, and lightweight wearable electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3777-0
Optically clear adhesives (OCAs) are critical for next-generation optoelectronic systems, yet their end-of-life management remains a sustainability challenge. Here, we report a debondable and robust polyurethane (PU)-based OCA that integrates both mechanical and chemical recyclability. The PU-based OCA exhibits high optical transparency (>90% transmittance from visible to near-infrared), strong adhesion to glass and polymeric substrates (bonding strength up to 5.0 MPa), and thermally sensitive H-bonding interactions that enable on-demand deadhesion at elevated temperatures. This capability facilitates non-destructive detachment of functional assemblies, promoting component reuse and material recycling. The adhesive demonstrates excellent mechanical properties, including ductility and strength, and outperforms several commercial optical adhesives in key performance metrics. Its straightforward synthesis and industrial scalability make it a promising solution for advancing circular economy principles in optoelectronic device manufacturing. The work addresses critical bottlenecks in balancing mechanical performance, adhesion/detachment, and recyclability, offering a transformative approach to sustainable advanced manufacturing.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024092906
Microplastic pollution in rivers and lakes has become a research hotspot, yet studies in Anhui Province have predominantly focused on northern and central regions, leaving southern Anhui under-investigated. This study addresses that gap by examining the Xin'an River in Huangshan City, a typical river in southern Anhui. Surface water and sediment samples were collected in December 2023. In surface water, microplastic concentrations ranged from 350 to 3700 n·m−3, with particles of 0–0.5 mm dominating (33.93%). Fibrous shapes were most prevalent (59.83%), and colored particles accounted for 50.27%. In sediments, concentrations ranged from 25 to 200 n·kg−1, with 0–0.5 mm particles again dominant (49.63%). Fibers comprised 47.08% of sediment microplastics, and white particles accounted for 34.74%. Polymer analysis identified polyethylene terephthalate (PET) as the most abundant material (36.61%), followed by polyamide (PA) (23.22%). Source analysis suggests that fibrous microplastics originate primarily from fiber-based products such as clothing, home textiles, and fishing nets. These findings provide essential baseline data for water resource management, pollution assessment, and ecological remediation of the Xin'an River.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024102403
The rapid combustion of soot at low temperatures is critical for diesel engine cold-start emission control. This study investigates the effects of water vapor (H2O) and nitrogen oxides (NOx) on electricity-pulse-sparked catalysis (EPSC) for soot combustion over a ceramic filter paper-based potassium-supported antimony-doped tin oxide (K/ATO/CP) monolithic catalyst. Under EPSC with 2000 J pulses, the presence of H2O and NOx adversely affected soot combustion performance, yet average reaction rates remained high at 12.0 μmol·gcat−1·s−1 and 9.53 μmol·gcat−1·s−1, respectively, exceeding conventional thermal catalysis (<8 μmol·gcat−1·s−1). In situ Raman and concentration profiles revealed that electricity pulses promote rapid H2O desorption, effectively alleviating H2O poisoning and restoring catalyst activity. In contrast, NOx adsorption forms stable nitrates (e.g., KNO3) that desorb slower than the soot combustion process, leading to incomplete recovery of activity. These findings highlight the importance of adsorbate desorption kinetics in EPSC and suggest that using weakly basic alkaline-earth metals (e.g., Mg, Ca, Sr) with lower nitrate decomposition temperatures could mitigate NOx poisoning. The results provide guidance for advancing EPSC technology in hybrid vehicle exhaust aftertreatment systems.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604004
Tire wear particles (TWPs) are emerging pollutants and constitute the dominant type of microplastics (MPs) in urban stormwater runoff, accounting for up to 90% of MPs in some cases. They are characterized by small size, high mobility, complex composition, and significant toxicity. Current research on TWPs remains fragmented, lacking a comprehensive understanding of their environmental behaviors and pollution control in aquatic systems. This review systematically analyzes the enrichment and vectoring roles of TWPs for coexisting pollutants, and their environmental fate, including ecotoxicological impacts, detection methodologies, release of intrinsic additives, and aggregation and sedimentation behaviors. Drawing on insights from other microplastic studies, the paper explores control technologies across the pollution pathway—source, transport, and terminal treatment—and proposes feasible management strategies. Key findings indicate that TWPs can adsorb heavy metals and organic contaminants, with adsorption capacities influenced by aging processes. Their aggregation is governed by solution chemistry, with critical coagulation concentrations varying with ionic strength and pH. The release of additives such as zinc and benzothiazoles is significant, posing ecological risks. Future research should focus on real-water aggregation mechanisms, additive release under natural conditions, long-term performance of treatment facilities like constructed wetlands under TWPs stress, enzymatic degradation pathways, and integration of AI, big data, and IoT for cost-effective detection and risk modeling. This review provides a scientific basis for developing targeted pollution control measures for TWPs in aquatic environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3485-0
Aqueous Zn-ion batteries (AZIBs) are promising for next-generation energy storage due to high safety and low cost, but their practical use is limited by Zn dendrite growth and side reactions. An ideal anode/electrolyte interphase should block water contact while enabling fast Zn2+ transport, yet conventional thick interphases increase ionic resistance and polarization. Here, we report a hydrophobic yet ultrathin (~5 nm) polydimethylsiloxane (PDMS) artificial interphase fabricated via conformal coating. The oxygen-rich PDMS layer selectively coordinates Zn2+ while its superhydrophobicity excludes water, and the ultrathin nature enables rapid Zn2+ conduction, enhancing the Zn2+ transference number by 2.28-fold. This synergistic design suppresses dendrites and mitigates hydrogen evolution. The PDMS-modified anode achieves 99.9% Coulombic efficiency over 3500 cycles, 880-hour symmetrical cell operation at 60% depth of discharge, and 2500-cycle full-cell endurance under lean Zn conditions (N/P ratio 5.7). Proof-of-concept pouch cells sustain 1400 cycles with a 0.01% decay rate. This molecular-scale interphase strategy provides a feasible pathway toward practical AZIB implementation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4054-x
The sluggish kinetics and high onset potentials of the oxygen evolution reaction (OER) at the anode of alkaline water/seawater electrolyzers limit overall energy efficiency. Noble-metal oxides like RuO2 are active but suffer from high cost, agglomeration, and dissolution under oxidizing potentials, especially in chloride-rich electrolytes where competing chloride oxidation reaction (ClOR) occurs. Here, we report a mild two-step dry-wet milling strategy to achieve throughout lattice doping of F− into MnO2 (F-MnO2) and subsequent anchoring of atomically dispersed Ru via Ru–O/F hybrid bonds. The strengthened Mn 3d–O/F 2p hybridization and negative charge shielding of surface F− enhance OER activity/selectivity relative to ClOR and impart superior Cl− tolerance and corrosion resistance. The resulting F-Ru-MnO2-TH electrocatalyst exhibits overpotentials of 280 mV and 200 mV at 10 mA cm−2 in alkaline water and simulated seawater, respectively. It retains ~100% of initial activity after 200 h continuous operation in alkaline media and >95% after 300 h in simulated seawater, significantly outperforming Ru-MnO2 and commercial RuO2. This work provides a scalable route to durable, high-performance OER catalysts for seawater electrolysis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3464-4
Photocatalytic conversion of atmospheric CO2 (0.03%) into multi-carbon fuels remains a grand challenge due to the high energy barrier of C–C coupling and the low concentration of CO2. Here, we report the construction of multiple metal pair sites on metal oxide nanosheets to steer C–C coupling, enabling efficient photoreduction of air-concentration CO2 to ethane (C2H6). As a prototype, Au nanoparticles were anchored on Bi4Ti3O12 nanosheets (Au-Bi4Ti3O12). High-resolution transmission electron microscopy and X-ray photoelectron spectroscopy confirmed the formation of Au-Ti metal pair sites at the interface. In situ Fourier transform infrared spectroscopy revealed the presence of *OCCOH intermediate on Au-Bi4Ti3O12 during CO2 photoreduction, which was absent on pristine Bi4Ti3O12. Density functional theory calculations showed that the Gibbs free energy for *CO–COH formation on Au-Bi4Ti3O12 is 2.23 eV, significantly lower than that on Bi4Ti3O12 (3.59 eV), indicating facilitated C–C coupling. Consequently, Au-Bi4Ti3O12 exhibited a C2H6 evolution rate of 2.58 μmol g−1 h−1 under 0.03% CO2, whereas Bi4Ti3O12 produced only C1 products (CO and CH4). This work demonstrates the first single-catalyst photoreduction of atmospheric CO2 to C2H6, highlighting the effectiveness of engineered multiple active sites in overcoming the C–C coupling bottleneck.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3640-3
Cancer immunotherapy, particularly small-molecule immune checkpoint inhibitors (ICIs), offers low cost and high tumor diffusion but suffers from limited efficacy and systemic toxicity. Here, we engineered non-pathogenic Escherichia coli MG1655 for tumor-targeted and synergistic photothermal immunotherapy. Polydopamine (PDA) was coated onto the bacterial surface via in situ polymerization, followed by noncovalent attachment of the IDO-1 inhibitor NLG919, yielding MG1655@PDA-NLG. The functionalized bacteria retained viability and bioactivity while exhibiting outstanding photothermal conversion. In a murine CT26 colon tumor model, intravenous injection led to effective tumor accumulation within 12 h and complete clearance from major organs by 72 h, with negligible hematological toxicity, confirming hypoxic tumor-targeting and biosafety. Under near-infrared irradiation, the engineered bacteria inhibited tumor growth by over 90%, combining photothermal effect and immunogenic cell death (ICD) to promote dendritic cell maturation. This synergized with suppression of tryptophan metabolism, enhancing CD4+ and CD8+ T cell infiltration. This work demonstrates a simple, safe strategy for surface engineering of bacteria with multiple therapeutic agents, offering a promising approach for precise and combined cancer immunotherapy.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60631-1
Methane dehydroaromatization (MDA) offers a carbon-neutral route to benzene, toluene, and xylene (BTX), yet the regulatory mechanisms of Brønsted acid site (BAS) strength and spatial proximity to Mo sites remain unresolved. This study systematically tunes BAS strength via isomorphous substitution (Al, Ga, Fe, B) and Mo-BAS proximity in ZSM-5, integrating catalytic evaluations with density functional theory (DFT). Strongly acidic Al-zeolites achieve the highest methane conversion, while weakly acidic B-substituted systems exhibit optimal mono-/bifunctional synergy, outperforming moderate-acid counterparts. DFT reveals that deprotonation energy (DPE) correlates with acid strength; Al-ZSM-5 (DPE = -5.68 eV) lowers the C–H activation barrier (ΔG = 1.467 eV). Spatial proximity analysis shows that nanoscale Mo-BAS distances, achieved via ball milling, enhance methane conversion by 33% and BTX yield by 31% compared to micrometer-scale mixtures, by accelerating intermediate transport and suppressing coke. These findings establish a multi-scale framework linking acid strength, spatial confinement, and electronic modulation, providing actionable guidelines for designing next-generation MDA catalysts.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60629-3
This study reports the synthesis of a novel Z-scheme heterojunction composite film comprising Ag/Bi2MoO6/BiOBr via electrochemical processes, ion-exchange techniques, and subsequent photodeposition of silver nanoparticles. The incorporation of Ag nanoparticles exploits localized surface plasmon resonance (LSPR) effects and serves as an electron mediator, establishing a Schottky barrier that suppresses charge recombination. The optimized 1.5% Ag/Bi2MoO6/BiOBr film achieves a CO production rate of 13.65 μmol/(g·h) from photocatalytic CO2 reduction, significantly outperforming the unmodified Bi2MoO6/BiOBr film. Photocurrent and impedance analyses confirm enhanced charge separation in the Ag-modified composite. A non-linear relationship between Ag loading and photocatalytic efficiency was observed, with optimal performance at 1.5% Ag. The proposed Z-scheme mechanism elucidates the synergistic interactions among components, providing a scientific basis for rational design of advanced photocatalysts and immobilized systems for CO2 reduction. This work offers insights into the development of efficient, sustainable photocatalytic technologies for carbon capture and utilization.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012404
Antibiotics, widely used for disease prevention and growth promotion in livestock, are emerging contaminants with potential risks to human health via the food chain. This review systematically analyzed the sources and residual levels of tetracycline (TCs) and β-lactam antibiotics in raw, pasteurized, commercial, and ultra-high-temperature (UHT) sterilized milk from various countries between 2012 and 2024, based on quantitative detection methods such as LC-MS and HPLC. The highest concentrations of TCs were found in milk from Algeria and Iran, while β-lactam residues were most elevated in Algeria, Bangladesh, and Kenya. The predominant TCs were tetracycline, chlortetracycline, and oxytetracycline; β-lactams were mainly penicillin and amoxicillin. Health risk assessment using hazard quotient (HQ) and hazard index (HI) revealed that all individual HQ values were below 1, indicating no significant non-carcinogenic risk from single antibiotics. However, the HI for multiple antibiotics in raw milk from Algeria exceeded 1, suggesting potential cumulative health risks. Furthermore, some studies reported residue concentrations surpassing maximum residue limits (MRLs), underscoring the need for continuous monitoring and control. This review highlights the global variability in antibiotic contamination and the importance of comprehensive risk assessment to safeguard public health.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60622-0
Photocatalytic production of hydrogen peroxide (H2O2) from sustainable biomass-derived carbon catalysts offers a renewable route to valuable chemicals, yet the regulatory role of surface functional groups on reaction kinetics remains underexplored. Here, hydrothermal carbon spheres (CS) rich in oxygen-containing functional groups demonstrated a remarkably high H2O2 production rate of 653 μmol/(g·h) in both pure water and actual seawater, without any sacrificial agent. The catalyst also exhibited outstanding activity in visible-light-driven photocatalytic oxidation of benzylamine to imines, achieving 92% conversion and >99% selectivity. Comprehensive analysis revealed that CS was rich in surface oxygen-containing functional groups, a feature strongly associated with its high photocatalytic efficiency. The observed positive Zeta potential of CS in seawater likely diminished electrostatic repulsion against positively charged intermediates, facilitating their accumulation at the liquid-solid interface. This work proposes a strategic framework for developing metal-free photocatalysts from biomass, offering a sustainable pathway for photocatalytic applications.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605004
To address the decline in operational performance of sewage pipeline networks in rainy cities of southern China caused by structural defects, stormwater-sewage cross-connections, and external water intrusion, a systematic governance framework comprising precise investigation, dynamic regulation, graded rehabilitation, and smart operation and maintenance was established. A zoned priority evaluation model was developed with comprehensive problem severity (P) and governance contribution (B) as core indicators, based on which differentiated governance strategies were formulated. Supported by a digital platform, monitoring, assessment, rectification, and verification data were integrated to develop a digital twin system for the pipeline network, and a correlation-based analysis and closed-loop operation and maintenance mechanism linking rainfall, groundwater level, and network hydraulic load was established. A typical urban area in Jiangxi Province was selected as the case study. After implementation, the mean COD concentration of terminal sewage in the study area increased steadily to above 230 mg/L, the average daily external water volume in the dry season decreased by 27.64%, and the sewage collection rate increased to 76%. The results indicate that the proposed framework can effectively support the quality and efficiency improvement of sewage pipeline networks in rainy cities of southern China, and provide a technical reference for similar cities.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225250
Slag foaming is a critical phenomenon in electric arc furnace (EAF) steelmaking, enhancing thermal efficiency, suppressing metal splashing, and stabilizing the refining process. Accurate prediction and control of slag foaming are essential for green and efficient steelmaking. This review systematically examines research progress on slag foaming prediction, clarifying the applicability, advantages, and limitations of different predictive methods to support intelligent control of foamy slags. Following the framework of 'influencing factors-prediction methods-development trends', the study summarizes the coupling effects of multiple variables such as basicity, viscosity, surface tension, suspended particles, gas parameters, and temperature on foam formation and stability. It compares five major prediction approaches: empirical formulas, dimensionless modeling, thermodynamic calculations, computational fluid dynamics (CFD) simulations, and machine learning models, analyzing their core concepts, merits, and constraints. Results indicate that single models often struggle to balance real-time capability and accuracy, particularly under multi-variable coupling and complex operating conditions. Therefore, a hybrid prediction framework combining mechanism-based and data-driven models is proposed, emphasizing physical constraints, multi-scale coupling, and multi-source data fusion. This integrated approach is expected to advance slag foaming prediction from 'computable' to 'controllable and adjustable', offering methodological insights for the development of green and intelligent EAF steelmaking.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3822-y
Precise control over supramolecular chirality and circularly polarized luminescence (CPL) is achieved through fluorene-content engineering of alkylated fluorene-quinoxaline copolymers. By systematically varying the fluorene ratio, three polymers (F8QX, F8QX-II, F8QX-III) are synthesized and co-assembled with a chiral inducer (R/S-5011). Thermal annealing induces highly ordered, crosslinked superstructures with strong chiroptical activity, where the dissymmetry factor (g_lum) decreases with increasing fluorene content. The optimal system, (F8QX)0.7-(R/S-5011)0.3, achieves a high |g_lum| of 0.52. Structural analyses and molecular dynamics (MD) simulations reveal that lower fluorene ratios facilitate tighter π–π stacking and more efficient chirality amplification. This system further serves as an excellent host for a narrowband multi-resonance thermally activated delayed fluorescence (TADF) emitter (DBN-ICZ) via Förster resonance energy transfer, yielding ternary co-assemblies with narrowband green emission (FWHM = 25 nm) and strong CPL with g_lum of 0.43. Circularly polarized organic light-emitting diodes (CP-OLEDs) based on (F8QX)0.7-(R/S-5011)0.3-(DBN-ICZ)0.005 exhibit yellow circularly polarized electroluminescence with |g_EL| value of 0.12. This work provides a comprehensive strategy integrating molecular design, hierarchical assembly, and energy transfer toward high-performance chiral optoelectronic materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4046-6
The deliberate control of framework dimensionality represents a powerful yet underexplored strategy for tailoring the functionality of homochiral metal-organic frameworks (HMOFs). Herein, we report a logical dimensional evolution from 1D and 2D to 3D HMOFs, achieved by tuning the connectivity of the auxiliary ligand. Employing a planar, three-connected ligand, 2,4,6-tri(pyridin-4-yl)-1,3,5-triazine (Tpt), together with enantiopure tetracarboxylate of cyclohexane diamide linkers ((1R,2R/1S,2S)-cyclohexane-1,2-dicarbonyl bis(azanediyl)diisophthalate) (R,R/S,S-CHCAIP) and Zn2+ salts, a pair of 3D porous HMOFs (P/M-HMOF-5) was successfully constructed. The 3D framework features unique heart-shaped channels and a novel 4-(3,3,3,6)-connected topology. Structural analyses reveal trinuclear Zn3(μ3-O) clusters that, upon activation, generate open metal sites. These Lewis acid sites, synergizing with Lewis basic sites from the framework, confer efficient acid-base bifunctional heterogeneous catalysis for the synthesis of 2,3-dihydroquinazolinones in excellent yields (90%–98%). Furthermore, P/M-HMOF-5 serve as highly sensitive and enantioselective fluorescent sensors for amino acids and α-hydroxy carboxylic acids, with the highest discrimination observed for phenylalanine (KBH(D-Phe)/KBH(L-Phe) = 5.85 for M-HMOF-5). This work demonstrates how rational ligand connectivity steers dimensional evolution, enabling the integration of distinct catalytic and sensing functions within a single chiral platform, thereby providing a blueprint for the design of advanced multifunctional materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3834-x
Lithium metal anodes face critical barriers to practical application due to dendritic growth and interfacial instability, which cause short cycle life and safety hazards. This work introduces a highly stable and ultrahigh-rate lithium metal anode using a lithiophilic Sm2S3-modified carbonaceous host. The in situ formation of a Li2S-reinforced interphase layer enables highly reversible lithium plating/stripping and uniform deposition. The modified anode achieves an ultrahigh rate capability of 20 mA cm−2 and ultralong cycling stability of 7440 cycles with dendrite-free morphology. In a 4.5 V anode-less Li||LiCoO2 cell with an areal capacity of ~1.93 mA h cm−2, the system sustains over 1100 cycles with 87.2% capacity retention under harsh conditions: an ultralow negative-to-positive capacity ratio (N/P) of ~0.26 and lean electrolyte of ~5 g Ah−1. Furthermore, an anode-less pouch cell with an ultrahigh areal capacity of ~6.01 mA h cm−2 delivers superior cycling performance even at an ultra-low N/P ratio of ~0.71 and ultra-lean electrolyte of ~1 g Ah−1, achieving a high energy density of 505 Wh kg−1. This work provides a scalable and effective strategy for advancing reliable, practical lithium metal batteries.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509078
The rapid expansion of photovoltaic (PV) installations and the impending retirement of early-stage modules have made the recycling of end-of-life PV modules an urgent issue. This review systematically examines the types and structures of retired PV modules, with a focus on crystalline silicon (c-Si) and thin-film technologies. It critically evaluates the principles, processes, and pros and cons of physical, chemical, pyrolysis, biological, combined, and emerging methods for recovering c-Si modules. The current status of silicon, metal, and valuable component recovery processes is summarized. For thin-film modules, the core technologies for recovering valuable components via pyrometallurgical, hydrometallurgical, biological, and novel approaches are analyzed in depth. Results indicate that conventional methods (physical, chemical, pyrolysis) remain dominant but suffer from high energy consumption, pollution, and chemical usage. Emerging technologies such as biological and green leaching are identified as key research directions, though they face challenges of low technical maturity and high costs. Finally, policy orientations and existing challenges are discussed, and future development directions are proposed, providing significant guidance for the sustainable and large-scale green development of the PV industry.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510013
To investigate the spatiotemporal distribution of nutrients and chlorophyll-a (Chl-a) in Dongping Lake, a coupled hydrodynamic-water quality-ecological model was developed using Delft3D. The model simulated total nitrogen (TN), nitrate nitrogen (NO3-N), ammonia nitrogen (NH4-N), total phosphorus (TP), soluble reactive phosphorus (SRP), and Chl-a. After validation, the model systematically analyzed the spatiotemporal patterns and influencing factors, revealing nitrogen and phosphorus transformation pathways. Results showed three temporal phases: relatively stable concentrations from January to April, significant fluctuations from May to August, and gradual stabilization from September to December, with peak timing varying among indicators. Spatially, concentrations were generally higher in the south and lower in the north, but NH4-N, TP, and Chl-a exhibited reverse patterns (higher in north) during certain periods. External inputs, primarily from the Dawen River, dominated the overall distribution, while water temperature, dissolved oxygen, and hydrodynamic conditions further modulated internal variability. Nitrogen and phosphorus showed distinct fates: nitrogen was primarily removed via denitrification and anammox, whereas phosphorus tended to transform into particulate forms and remained in the lake for extended periods. These findings provide scientific support for precise water quality management in Dongping Lake.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509124
To reveal the spatiotemporal evolution and driving mechanisms of water quality in the Hanjiang River Basin, this study utilized monthly water quality monitoring data from 54 sections from January 2021 to April 2024. Methods including single-factor index, comprehensive water quality index (WQI), principal component analysis (PCA), and optimal parameters-based geographical detector (OPGD) were employed. Results indicated significant spatiotemporal differences, with total nitrogen (TN), chemical oxygen demand (COD), and permanganate index (CODMn) as major pollutants, TN being the most critical. Temporally, agricultural non-point source organic pollution dominated in wet season, while comprehensive organic pollution with industrial point source characteristics prevailed in dry season. Spatially, water quality deteriorated along the main stream, with tributary downstream areas showing severe pollution, forming a pattern of 'mountainous areas good, plains poor'. OPGD revealed combined effects of natural conditions and human activities, proposing a 'zonal control and targeted treatment' strategy.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2026.JFCT.0001
The escalating global demand for carbon reduction has positioned chemical absorption using alkanolamine solvents as the predominant post-combustion CO2 capture technology, owing to its high absorption efficiency and process maturity. However, the regeneration of CO2-rich solvents is energy-intensive, with the desorption step accounting for 40.0%–60.0% of total energy consumption. Traditional amine-based methods suffer from high energy penalties, solvent degradation, and equipment corrosion, limiting scalability. Catalytic CO2 desorption, employing solid acid catalysts (SACs), has emerged to address these challenges by lowering the activation energy for CO2 release, enhancing reaction kinetics, and enabling efficient regeneration at lower temperatures (110–130 °C reduced). This review systematically examines research from the past five years on key catalyst materials, focusing on structure-activity relationships, synergistic mechanisms of Lewis acid, Brønsted acid, and basic sites, and their influence on desorption pathways. It highlights that SACs not only improve desorption dynamics but also facilitate catalyst recovery, avoiding adverse effects on absorption. The paper analyzes current scientific and technological challenges, including catalyst stability, selectivity, and scale-up, and provides an outlook on industrial application in low-cost carbon capture. Key findings indicate that catalysts such as metal-organic frameworks (MOFs), heteropolyacids, and waste-derived materials can reduce regeneration energy by up to 30%–40% while maintaining high desorption efficiency. The review underscores the potential of catalytic regeneration to significantly lower operational costs and enhance the viability of amine-based CO2 capture in industrial settings.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025030501
Coastal areas serve as critical ecological interfaces for the migration of terrestrial microplastics (MPs) into the ocean, and characterizing their pollution is essential for integrated coastal management. This study investigated the occurrence, sources, and ecological risks of MPs in surface waters of nearshore areas and river estuaries around Hainan Island, a typical tropical tourist island. MPs abundance ranged from 316.67 to 1300 n·m−3 in seawater and from 400 to 5416.67 n·m−3 in river water. In seawater, the dominant polymer was polyethylene terephthalate, with fibers being the predominant shape, size class 500–1000 μm, and white/transparent color. In river water, polypropylene-ethylene copolymer dominated, also as fibers, but with size class 100–500 μm and white/transparent color. Seawater MP abundance showed a significant positive correlation with tourist numbers, and distribution across functional areas followed: tourism areas > natural areas > aquaculture areas > residential areas. Multiple correspondence analysis identified household plastic waste, laundry wastewater, aquaculture, and fishery products as primary sources of seawater MPs. Principal component analysis indicated homologous characteristics between seawater and river MPs, suggesting rivers are a major pathway for terrestrial MP transport to coastal zones. Ecological risk assessment revealed low pollution loads, with potential ecological risks moderate for seawater and medium-low for river water. Notably, 15% of seawater sampling sites exhibited polymer risk level Ⅳ, primarily driven by polyacrylonitrile's high biological toxicity. These findings provide a scientific basis for developing MP pollution control strategies in Hainan Island.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60660-3
Catalytic oxidation is a pivotal technology for the valorization of light hydrocarbons, with oxidative dehydrogenation (ODH) and epoxidation using molecular oxygen attracting significant interest due to high atom economy and environmental friendliness. This review systematically summarizes recent advances in the oxidative dehydrogenation of light alkanes (ethane, propane) and aerobic epoxidation of light olefins (ethylene, propylene). For rational catalyst design, it elaborates on performance regulation strategies for metal oxide catalysts such as MoVNbTeOx mixed oxides, NiO-based, and V-based systems, as well as carbon/boron-based non-metal catalysts in alkane ODH, and silver- and copper-based catalysts in alkene epoxidation. Strategies include regulating the oxidation state of active sites, exploiting strong metal-support interactions, engineering particle size and crystal facets, and promoter modification. At the mechanistic level, combining density functional theory calculations with in situ characterization, the review examines C–H bond activation and alkene desorption pathways in ODH, and oxygen insertion routes and competing side reactions in epoxidation. Special attention is given to the dynamic evolution of electrophilic and nucleophilic oxygen species and their decisive role in selectivity. Persistent challenges include suppressing over-oxidation and overcoming the conversion–selectivity trade-off. Future directions propose precise design of active centers, development of inherently safer processes, and in-depth analysis of complex reaction networks, supporting the green transition of the chemical industry.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025022102
Organophosphate pesticides (OPs), the most extensively used insecticides globally, are ubiquitous in environmental matrices and agricultural products, leading to widespread human exposure. This systematic review evaluates the impact of OP exposure on pregnancy complications and adverse birth outcomes, synthesizing evidence from 58 epidemiological studies published between January 2001 and July 2024. Exposure assessment methods, including biomarkers such as urinary dialkyl phosphates, are critically examined. The review finds significant associations between OP exposure and increased risks of spontaneous abortion, gestational diabetes mellitus, gestational hypertension, preeclampsia, preterm birth, and adverse birth outcomes such as low birth weight and reduced head circumference. Potential mechanisms include paraoxonase 1 (PON1) genotype polymorphisms affecting detoxification capacity, oxidative stress, inflammation, metabolic disruption, and altered placental gene networks. The review highlights inconsistencies across studies due to variability in exposure assessment, timing, and population susceptibility. Future research should prioritize longitudinal designs, repeated biomarker measurements, and consideration of PON1 genetic variants to clarify causal relationships and susceptible windows. This comprehensive synthesis provides critical insights for regulatory policies and clinical interventions aimed at mitigating maternal and child health risks from OP exposure.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025021902
Polyacrylonitrile (PAN) ultrafiltration membranes are widely used in water treatment, yet their anti-fouling performance remains a challenge. In this work, PAN was first reacted with sodium azide via click chemistry to synthesize 1,2,3,4-tetrazolium polyacrylonitrile (PAN-N). Subsequently, PAN-N was reacted with iodoacetamide (IAM), 2-iodoethanol (IH), iodoacetic acid (IA), and chlorosulfonic acid (CSA) to introduce hydrophilic groups, and anti-fouling PAN ultrafiltration membranes were fabricated via phase inversion. The membranes were characterized by Fourier transform infrared spectroscopy, 1H nuclear magnetic resonance, X-ray diffraction, scanning electron microscopy, and contact angle measurements. Results showed that the PAN-N membrane exhibited superior performance to pristine PAN, with water flux increasing from 0.9233 to 1.232 L·(m2·h·kPa)−1 and bovine serum albumin (BSA) rejection from 69.23% to 82.4%. Hydrophilic modification further enhanced performance; the PAN-N-IA membrane achieved the highest water flux of 1.7347 L·(m2·h·kPa)−1 and rejection of 93.57%. Anti-fouling tests revealed that modified membranes followed the order: PAN-N-CSA > PAN-N-IA > PAN-N-IH > PAN-N-IAM > PAN-N > PAN. PAN-N-CSA and PAN-N-IA showed comparable anti-fouling performance, with total fouling indices of 56.1% and 58.47%, reversible fouling indices of 47.17% and 46.97%, and irreversible fouling indices of 8.97% and 11.47%, respectively. This work demonstrates that PAN-N-IA membranes combine high flux, high rejection, and excellent anti-fouling properties, making them promising for water treatment applications.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025092801
Urban river water quality is critically influenced by outfall discharges, yet the seasonal dynamics of dissolved organic matter (DOM) and its linkage to water quality remain poorly constrained. This study collected outfall water samples seasonally during 2023–2024 along the Nanfei River and Banqiao River in Hefei, Anhui Province. Parallel factor analysis of excitation-emission matrices identified three fluorescent components: fulvic acid-like C1, tryptophan-like (protein-like) C2, and terrestrial humic-like C3. Seasonal variations were pronounced: protein-like C2 dominated in winter and spring, whereas summer and autumn showed lower C2 proportions due to rainwater dilution and urban nonpoint source runoff inputs. Water quality indices decreased in summer and autumn, primarily attributed to dilution by rainfall runoff. Fluorescence index (FI > 1.9) and biological index (BIX > 1.0) indicated predominantly autochthonous DOM sources. During summer and autumn, humification index (HIX) and specific UV absorbance (SUVA) increased, while spectral slope ratio (SR) decreased, suggesting enhanced terrestrial and urban runoff influence. Significant positive correlations were observed between protein-like C2 and terrestrial humic-like C3 with water quality parameters, indicating their utility as precise indicators of pollution sources and seasonal water quality variations. These findings provide a scientific basis for integrated management of urban outfalls.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3794-0
Luminescent transparent display technology is widely used in emerging fields such as augmented reality glass, head-up vehicle display, and commercial retail windows. While electroluminescent display is well established, the photoluminescent transparent screen of full-color rendering ability remains elusive due to the severe crosstalk between emitters. Herein, a full-color transparent screen of an orthogonal red/green/blue (R/G/B) luminescence is reported. Lanthanide fluoride nanocrystals are used as the emitters, where the color is tuned by a deliberate choice of doping activators including Tb3+, Eu3+, and Tm3+. Polyvinyl alcohol, with an identical refractive index to nanocrystals, is employed as the host matrix, enabling a high transparency up to 86% in the visible region upon a high loading content (~78 wt%) of nanocrystals. It should be noted that the nanocrystals are embedded in separate monolayers before integration by a UV-selective absorber, i.e., epoxy resin, which absorbs 254-nm UV to block cross-excitation between Tb3+ and Eu3+ layers, providing an asymmetric luminescent property from both sides of the screen. In a proof-of-concept experiment, a full-color prototype is showcased in real time for its potential applications in advanced displays of immersive experience.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3810-y
Amorphous metal-organic frameworks (aMOFs), with abundant defects and unsaturated coordination sites, are ideal precursors for investigating electrocatalytic reconstruction mechanisms. However, systematic understanding of how different modulation strategies affect reconstruction pathways and final active species remains lacking. Here, an amorphous MOF constructed from 3,4,9,10-pyrene-tetracarboxylic acid (PTA) serves as a controllable precursor to compare doping and alloying effects on structural reconstruction and oxygen evolution reaction (OER) performance. Doping promotes preferential reconstruction into Fe-rich (oxy)hydroxides with more exposed active sites, whereas alloying yields Fe-Co mixed (oxy)hydroxides with limited site exposure. The doped system FeCo0.05-PTA exhibits outstanding OER activity in alkaline conditions, with overpotentials of 208 and 248 mV at 50 and 100 mA cm−2, respectively, and a low Tafel slope of 36.2 mV dec−1. In situ Fourier transform infrared spectroscopy (FTIR) captures the OOH* intermediate, confirming the adsorbate evolution mechanism. Density functional theory (DFT) calculations show the doped system has the lowest free-energy barrier (ΔG = 0.59 eV) at the rate-determining step. This study underscores the decisive role of precursor design, elucidates distinct effects of doping and alloying on reconstruction pathways and final properties of amorphous MOF-derived (oxy)hydroxides, and provides insights for designing related electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3889-6
Photocatalytic hydrogen production is fundamentally limited by inefficient charge separation and asynchronous supply of electrons and protons to active sites. Here, we designed a ZnIn2S4/ZnCo2S4 (ZIS/ZCS) heterojunction with an atomically coherent interface achieved via an ultralow lattice mismatch of 0.05%. This unique structure promotes rapid electron transfer through a built-in electric field and facilitates continuous proton migration via a hydrogen spillover effect, thereby synchronizing electron and proton delivery at the catalytic interface. This dual regulation of electrons and protons synergistically promotes proton-coupled electron transfer, resulting in a high hydrogen evolution rate of 70.3 mmol g−1 h−1 and selective oxidation of benzyl alcohol to aldehyde (39.3 mmol g−1 h−1) with 93.6% selectivity. This work demonstrates the critical importance of lattice match and dual charge-proton management in designing efficient photocatalysts for complex redox reactions.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3893-y
Perovskite photolithography, an emerging research frontier, combines the unique properties of perovskite materials with lithographic processes for advanced optoelectronic applications. Currently, bottom-up photolithography is preferred due to perovskites’ intrinsic characteristics, while top-down photolithography offers better compatibility with mature semiconductor manufacturing workflows. In this study, we innovatively propose an integrated technology that merges top-down photolithography with in situ phase-transition strategy. Utilizing non-emissive Cs4PbBr6 perovskite single crystals (SCs) as both structural templates and reaction sources, we achieve spatially selective patterning by precise wet and dry etching, followed by inductively coupled plasma (ICP)-induced Cs4PbBr6 to CsPbBr3 phase transition. This process facilitates the direct fabrication of highly emissive CsPbBr3/Cs4PbBr6 microstructure patterns inside Cs4PbBr6 SCs. Such a synergistic approach simplifies perovskite photolithography procedures and enables rapid, large-scale manufacturability. Furthermore, its integration with machine learning optimization algorithms showcases promising application potential in intelligent anti-counterfeiting. This novel approach, integrating perovskite SCs homologous substrate with customized photolithography, provides a new strategy for fabricating high-performance perovskite optoelectronic devices and is expected to promote technological advancement.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3851-3
Aqueous zinc-ion batteries (AZIBs) face critical challenges from zinc anode instability, including corrosion, hydrogen evolution reaction (HER), parasitic byproduct formation, and uncontrolled dendrite growth. To address these issues, we developed a multifunctional cerium-based metal-organic framework (Ce-MOF) coating for zinc anodes. The coating features an ordered porous structure and inherent properties that mitigate HER, suppress side reactions, and inhibit dendrite formation. Symmetric cells using Ce-MOF/Zn demonstrated exceptional cycling stability for over 2060 h at 0.5 mA cm−2 with a low hysteresis polarization of 26 mV. In full cells with an I2@AC cathode, the Ce-MOF/Zn||I2@AC achieved outstanding cycling stability of 28,550 cycles at 5 A g−1, with 91% capacity retention (109.6 mAh g−1). Through integrated characterization employing in-situ optical microscopy, ex-situ XRD, SEM, and DFT calculations, we elucidated the multifunctional mechanism: the Ce-MOF coating facilitates preferential (002)-oriented Zn deposition to suppress dendrites, reduces Zn2+ desolvation energy to enhance deposition kinetics, and modulates interfacial chemistry to mitigate HER and corrosion. This work establishes Ce-MOF coatings as a simple yet powerful strategy for developing high-performance zinc anodes, providing critical insights for advancing practical AZIB technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3900-8
Memristors, which leverage ion migration for resistance switching, offer breakthroughs in bionic perception, information security, and edge computing but face bottlenecks in functional integration and stability. Herein, we explore all-inorganic Cu3SbI6 nanocrystals (NCs) & PMMA composite memristors (Ag/PMMA&Cu3SbI6/ITO) regulated by NCs doping (0–15 wt%). The devices operate via electric field-induced Ag+ ion migration and conductive filament dynamics, where NCs act as local electric field enhancers. At a doping concentration of 4 wt%, stable bipolar switching (Ron/Roff > 2 × 10^3, cycling endurance > 700 cycles) enables the simulation of biological nociception/Pavlovian reflexes and the construction of basic logic gates. At 2 wt%, sparse NCs induce random filament formation for encryption key extraction, which integrates with 4 wt% logic gates to enable efficient encryption/decryption of text/image data. This work provides a strategy for designing multifunctional memristors by regulating ion transport through nanocrystal concentration, offering references for related functional integration and cross-disciplinary applications.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509036
Algal-derived phosphorus (P) constitutes a significant fraction in eutrophic lakes, with particulate phosphorus (PP) serving as both a major internal P reservoir and a potential target for P resource recovery. This study proposed a chitosan-coupled electroflotation (CEF) technology for efficient enrichment and recovery of algal-derived P from high-algal water. Using Taihu Lake algae-laden water as the test medium, the effects of chitosan dosage and voltage on the enrichment of different P fractions were systematically evaluated. Results showed that the optimal P enrichment was achieved at a chitosan dosage of 15 mg·L−1, and higher voltages further enhanced the enrichment efficiency. Under optimal conditions, PP accounted for 83.57% of the enriched P, indicating a strong capability for particulate P capture. The mechanism involved chitosan-induced flocculation via charge neutralization and sweep flocculation, while higher voltages increased the positive charge density of chitosan molecules, enhancing charge neutralization and electroflotation. In P release experiments, open conditions significantly promoted the transformation of PP to dissolved P, whereas closed conditions inhibited this process. Additionally, chitosan's antibacterial action and physical retention effectively limited P release. Compared with conventional metal salt coagulants, this method avoids metal ion residues, offering high environmental safety and providing a green and feasible approach for the harmless disposal and resource utilization of algal-derived P in eutrophic lakes.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510081
Electrochemical two-electron oxygen reduction (2e−ORR) for hydrogen peroxide (H2O2) synthesis faces challenges of low cathodic catalytic efficiency and complex catalyst preparation. This study prepared nitrogen-vacancy (Nv) rich carbon nitride via one-step pyrolysis, composited with carbon nanotubes (CNT), and loaded onto graphite felt (GF) to fabricate a non-precious metal gas diffusion electrode Nv-C3N4-CNT/GF. The electrode exhibited a three-dimensional fibrous skeleton with interconnected micro-nano hierarchical pores, facilitating efficient electron transport. Electrochemical impedance spectroscopy revealed a low charge transfer resistance of 13.26 Ω, indicating superior electrocatalytic activity and charge transfer efficiency. Single-factor experiments and response surface methodology (RSM) optimization determined optimal conditions: calcination temperature 300 °C, catalyst mass ratio 3:1, Nv-C3N4-CNT loading 0.1 g, current density 40 mA·cm−2, pH 7, and aeration rate 0.1 L·min−1. Under these conditions, H2O2 accumulation reached 1622.73 mg·L−1 after 90 min, which was 1.3 and 1.5 times higher than g-C3N4-CNT/GF and CNT/GF electrodes, respectively. Stability tests showed that after 6 cycles, H2O2 production remained at 1400.52 mg·L−1, and within 960 min, the maximum production reached 2014.04 mg·L−1 with a highest Faradaic efficiency of 54.86%. These results demonstrate the electrode's potential for cyclic use. This study provides a new approach for developing efficient, low-cost electrodes for electrosynthesis of H2O2, offering a reference for green H2O2 production.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60638-X
The extensive emission of greenhouse gases, primarily CO2 and CH4, has contributed to intensified global warming. Dry reforming of methane (DRM, CH4 + CO2 → 2CO + 2H2) offers a pathway for the synergistic utilization of these two major greenhouse gases, presenting important implications for both environmental protection and energy sustainability. However, the catalysts still face challenges such as carbon deposition and sintering of active metals, which adversely affect the catalytic performance and long-term stability. Oxygen vacancies, which are common lattice defects in metal oxides, have been demonstrated to improve the DRM performance by modulating the surface and interfacial properties of the catalysts. This review systematically summarizes research progresses in DRM over the past decade, outlines the major challenges and emphasizes the critical roles of oxygen vacancies in suppressing carbon deposition and inhibiting metal sintering. Furthermore, the mechanisms through which oxygen vacancies influence DRM reactions are discussed, combined with their formation pathways and regulation strategies. These insights provide essential theoretical foundations for the design and synthesis of highly efficient and stable DRM catalysts.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026021002
The construction of species sensitivity distribution (SSD) models using a single function requires optimization to reduce subjectivity. To minimize model selection uncertainty and align with Chinese freshwater organism effect criteria, this study integrated native freshwater species toxicity data, including experimental and predicted values from interspecies correlation estimation (ICE) and acute-chronic ratio (ACR) methods, and applied a model-averaging approach to construct SSD models for seven representative phthalate esters (PAEs): dimethyl phthalate (DMP), diethyl phthalate (DEP), dibutyl phthalate (DnBP), butyl benzyl phthalate (BBP), bis(2-ethylhexyl) phthalate (DEHP), diisodecyl phthalate (DIDP), and dihexyl phthalate (DnHP). The derived short-term predicted no-effect concentrations (PNECacute) for DMP, DEP, DnBP, BBP, DEHP, DIDP, and DnHP were 16.796, 4.984, 9.064×10⁻², 2.490×10⁻¹, 1.898×10⁻², 1.386×10⁻¹, and 7.428×10⁻² μg·L⁻¹, respectively. Long-term PNECs (PNECchronic) were 3.245×10², 36.500, 1.149, 4.018, 8.949×10⁻², 1.637, and 4.073×10⁻¹ μg·L⁻¹, respectively. These PNECs, based on native species toxicity data and more stringent than existing standards, are recommended as potential references for water quality criteria based on Chinese freshwater organism effects. Ecological risk assessment using the hazard quotient (HQ) method on exposure concentrations from typical Chinese freshwater basins revealed that DEHP and DnBP posed high short-term risks, BBP mainly medium risk, while DMP, DEP, and DnHP showed low or no risk. Long-term risks indicated DEHP at medium to high risk, DnBP mainly medium to low, BBP low or no risk, and DMP, DEP, and DnHP no risk. The overall ecological risk ranking was DEHP > DnBP > BBP > DEP > DMP ≈ DnHP.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025032001
This study investigates the variation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and their monomer components during low-temperature thermal decomposition (250–500 °C) of municipal solid waste incineration fly ash from a typical mechanical grate furnace. Results demonstrate that pyrolysis temperature and time significantly affect the solid-phase removal rates of PCDD/F mass concentration and toxic equivalent (TEQ) concentration. The influence weights of temperature on mass and TEQ removal rates are 20.86 and 21.41, respectively, while those of time are 4.27 and 3.36. Response surface analysis identifies optimal conditions at 380 °C for 1.0 h. At 250–300 °C, both PCDFs and PCDDs concentrations increase synchronously, indicating enhanced formation. At 300 °C for 2.0 h, high-chlorinated congeners undergo dechlorination to low-chlorinated ones, notably increasing 2,3,7,8-T4CDD (I-TEF=1.0) and 1,2,3,7,8-P5CDD (I-TEF=0.5). From 350 °C upward, significant degradation occurs; at 380 °C (1.0 h), degradation rates for PCDDs and PCDFs reach 97.8% and 97.6%, respectively, effectively reducing TEQ-contributing congeners. The process proceeds in two stages: initial dechlorination, followed by destruction of dioxin-like compounds at higher temperatures. 2,3,7,8-T4CDD emerges as a critical component for detoxification. These findings provide a scientific basis for optimizing thermal treatment of fly ash to minimize environmental and health risks.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026030202
High nitrogen (N) inputs, low N use efficiency, and substantial greenhouse gas emissions constrain sustainable double-cropping rice production in the middle and lower reaches of the Yangtze River. To evaluate whether humic acid urea (HAU) can reconcile yield stability with N reduction and carbon mitigation, a field experiment was conducted in a double-cropping rice system. Five treatments were established: conventional urea at the recommended N rate (U), HAU at the recommended N rate (HAU), conventional urea with a 20% reduction in N input (U-20), HAU with a 20% reduction in N input (HAU-20), and a no-N control (CK). Rice yield, N uptake and utilization, and the full life-cycle carbon footprint were quantified. Results showed that HAU significantly increased double-cropping rice yield by 6.46% (early rice) and 8.76% (late rice) compared to U (P < 0.05). HAU-20 maintained yield equivalent to U, while U-20 significantly reduced yield. HAU-20 significantly improved nitrogen fertilizer apparent utilization rate, agronomic efficiency, and partial factor productivity. Specifically, apparent utilization rate increased by 9.24 percentage points (early rice) and 7.80 percentage points (late rice); agronomic efficiency increased by 18.51% and 26.69%, and partial factor productivity by 22.79% and 25.58% for early and late rice, respectively (P < 0.05). Life-cycle carbon footprint was significantly reduced by 26.25% (early rice) and 40.38% (late rice) under HAU-20 compared to U, with per-unit product carbon footprint reduced by 0.22 t CO2-eq·t−1 and 0.86 t CO2-eq·t−1, respectively. The reduction was primarily attributed to decreased CH4 and N2O emissions: early rice CH4 and N2O cumulative emissions decreased by 28.92% and 44.34%, and late rice by 44.46% and 63.85% (P < 0.05). In conclusion, HAU with 20% N reduction sustains yield, enhances N use efficiency, and significantly lowers carbon footprint, offering a viable path for green and low-carbon double-cropping rice production.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607004
Pelletizing technology is widely applied in biomass and coal fuel processing, offering advantages in transport, storage, and energy density. Coal gasification fine slag (CGFS), a carbon-rich coal-based solid waste, holds potential as a fuel. This study prepared centimeter-scale composite pellets by blending CGFS with various biomass types under 6 MPa at room temperature for 2 minutes. Combustion and emission characteristics were investigated using a self-developed flat-flame macro-thermogravimetric reactor simulating high heating rate conditions. Results showed that biomass type significantly influenced combustion due to chemical composition differences. Introducing biomass altered fuel particle composition, enhancing combustion rates of single-component fuels by 3–5 times during volatile combustion. Co-combustion reduced NOx and CO emissions by over 50% compared to pure CGFS. Higher biomass ratios accelerated volatile release and shortened burnout time but increased NO emissions due to higher volatile nitrogen content. Conversely, CO emissions decreased due to improved char combustion conditions. These findings provide critical experimental support for optimizing clean and efficient solid fuel production from CGFS and biomass.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607011
Anaerobic digestion (AD) is a viable route for energy recovery from food waste (FW), yet it often suffers from process instability due to volatile fatty acids (VFAs) accumulation and subsequent pH drop. This study modified red mud (RM) with hydrochloric acid to produce acid-modified red mud (AMRM), aiming to optimize its alkalinity and physicochemical properties. The efficacy of AMRM as an additive in FW anaerobic digestion was systematically evaluated. Results demonstrated that adding 3% AMRM significantly enhanced the buffering capacity and controlled VFAs accumulation, particularly propionic acid. This was attributed to the developed pore structure of AMRM, whose specific surface area increased by 347% compared to raw RM, facilitating rapid VFAs adsorption. Furthermore, AMRM enriched hematite (Fe2O3), which elevated electron transport system (ETS) activity and coenzyme F420 content, suggesting its role as an electron carrier promoting direct interspecies electron transfer (DIET) between syntrophic bacteria and methanogens. Consequently, the cumulative methane yield reached 633.9 mL/g VS, which was 175.1% and 55.2% higher than the control and raw RM groups, respectively. The VS removal efficiency was 75.1%. This study provides a dual-pathway mechanism—adsorption and electron transfer—for enhancing AD performance, offering a cost-effective and sustainable strategy for FW treatment and RM valorization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4079-4
Utilization of ultrahigh-nickel LiNi_xCo_yMn_1-x-yO_2 (NCM) (x > 0.97) in Li-ion batteries can distinctively boost energy density through enhanced discharge capacity. However, capacity and thermal stability deteriorate as Ni content approaches the limit. Here, we propose a facile strategy by introducing high-valence tungsten (W) into ultrahigh-nickel polycrystalline LiNi_0.98Co_0.01Mn_0.01O_2 (PCNCM98). W-doped PCNCM98 (W-PCNCM98) exhibits refined, compactly stacked primary particles, whereas PCNCM98 shows equiaxial, non-uniform larger particles. The refined microstructure enhances mechanical strength: average particle hardness of W-PCNCM98 is 104 MPa, 1.5 times higher than PCNCM98 (68 MPa). This improved mechanical property suppresses lattice volume changes and relieves microcrack formation from H2–H3 phase transition. Consequently, cycling performance in pouch-type full cells is significantly enhanced, with capacity retention of 73% after 2000 cycles at 1 C and 25 °C, 54% higher than PCNCM98. Enhanced structural stability and strong electron affinity of W6+ also improve thermal stability: exothermic peak for W-PCNCM98 is postponed to 203 °C with heat generation of 1287 J g−1, versus 190 °C and 1528 J g−1 for PCNCM98. This high-valent doping strategy stabilizes ultrahigh-nickel NCM cathodes, accelerating large-scale EV applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3979-3
The escalating prevalence of multidrug-resistant Pseudomonas aeruginosa (P. aeruginosa) infections necessitates novel antibacterial strategies. Here, we engineered lectin B (LecB)-targeted glyco-dots (TFP2F) via self-assembly of a photosensitizer (TFP2) possessing aggregation-induced reactive oxygen species (ROS) generation capability with fucose-modified tetraphenylethene glycoclusters (TPE-Fuc4), enabling P. aeruginosa-targeted antimicrobial photodynamic therapy and wound healing promotion. Three photosensitizers (TFP0–2) featuring an “A-D-A” electronic structure were synthesized, exhibiting broad absorption bands and near-infrared (NIR) fluorescence. Among these, TFP2 demonstrated superior Type-I/II ROS production (including ·OH, ·O2−, and 1O2), achieving potent phototoxicity against P. aeruginosa (MIC80 = 7.5 μM). Self-assembly with TPE-Fuc4 yielded glyco-dots TFP2F that facilitated LecB-mediated bacterial targeting, enhanced bacterial uptake, and significantly reduced the MIC80 to 2.5 μM against drug-resistant P. aeruginosa under light irradiation. In a murine P. aeruginosa-infected wound model, TFP2F treatment combined with light irradiation accelerated wound closure to <20% of the initial area by day 8 (vs. >40% in controls) and eliminated >95% of bacteria by day 2. This work presents a convenient strategy for constructing glyco-dots as a potent functionalized platform for precision, lectin-targeted antimicrobial photodynamic therapy.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511055
To systematically investigate the spatiotemporal distribution of hydrodynamics and water quality under cascaded hydropower development in the upper Heihe River, a MIKE21-based water environment model was constructed for the mountainous reach. The model simulated the dynamic changes of total phosphorus (TP), total nitrogen (TN), and ammonia nitrogen (NH3-N) from January to August 2023. Calibration and validation against field data showed good performance: the hydrodynamic model achieved a coefficient of determination (R2) of 0.89 and a mean relative error (MRE) of 11.3%; the water quality model achieved an average R2 of 0.86 and an average MRE of 14.21%. Hydrodynamic simulations revealed average flow velocities of 1.78, 0.72, and 0.36 m·s−1 during wet, normal, and dry periods, respectively. Natural river sections exhibited high velocities up to 4.3 m·s−1, while reservoir sections had near-stagnant flow due to hydraulic structures. Water quality simulations indicated that TN and NH3-N concentrations were higher in dry and normal periods, whereas TP was higher in the wet period. Spatially, concentrations in reservoir sections exceeded those in natural sections: natural sections had TP, TN, and NH3-N concentrations of 0.07–0.10, 0.25–0.50, and 0.025–0.250 mg·L−1, respectively, while reservoir sections had 0.12–0.17, 0.60–0.80, and 0.10–0.45 mg·L−1. These findings provide scientific references for water environment management in the Heihe River and similar inland river basins.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511046
To evaluate the carbon footprint differences between the emerging ex-situ remediation facility mode and the conventional on-site remediation mode in China, this study employed the SEFA tool to calculate greenhouse gas (GHG) emissions and energy consumption for four typical remediation scenarios. Results indicate that the carbon emission intensity of solidification/stabilization (S/S) in the remediation facility is 12.00% higher than that of on-site S/S, with unit carbon intensities of 66.74 and 59.59 kgCO2e·m−3, respectively, and total energy consumption 11.90% higher. The soil transport segment in the facility S/S contributes 13% of carbon emissions, being the primary reason for its higher total carbon footprint. Conversely, thermal desorption (TD) in the facility exhibits 11.10% lower carbon emissions than on-site TD, with unit intensities of 269.16 and 302.78 kgCO2e·m−3, and total energy consumption 3.97% lower, mainly due to the utilization of landfill biogas as renewable energy for heat and power generation, while soil transport contributes only 3% of emissions. The reagent segment in S/S and the heat supply segment in TD account for 77%–86% and 70%–72% of total GHG emissions, respectively. The study demonstrates that remediation facilities, leveraging advantages such as landfill biogas, can actively aggregate contaminated soil from surrounding areas for centralized thermal desorption, which is beneficial for regional carbon emission reduction in soil remediation.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60752-9
Methanol steam reforming (MSR) is a pivotal process for efficient hydrogen production. This study employs density functional theory (DFT) calculations to comparatively analyze the MSR reaction mechanism on PdCu(111) and PtCu(111) bimetallic surfaces. The investigation unveils how alloying modulates reaction pathways and overall catalytic performance. Notably, Cu sites stabilize adsorption of OH and CH2O species, whereas Pd/Pt sites exhibit preferential affinity for CO. This spatial site separation facilitates progression along the formate pathway. PdCu(111) demonstrates superior overall catalytic performance compared to PtCu(111), with water dissociation identified as the rate-determining step (RDS), featuring an activation energy of only 0.74 eV. The bimetallic synergy breaks the inherent contradiction between activity and selectivity of monometallic catalysts: Cu sites serve as a source of hydroxyl groups, while Pd/Pt sites enhance C–H bond cleavage efficiency, ultimately enabling high methanol conversion alongside low CO formation. From the perspectives of electronic structure and geometric configuration, this study establishes a theoretical framework to guide rational design of high-performance bimetallic catalysts for MSR.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60672-X
Dry reforming of methane (DRM) converts CH4 and CO2 into syngas, offering a route to mitigate greenhouse gases. Ni-based catalysts suffer from sintering and carbon deposition at high temperatures. This work employs MgO-MgAl2O4 composite supports to regulate Ni loading and introduces Ce, La, and Zr as promoters to investigate their effects on DRM activity, structural stability, and surface oxygen species. Optimal Ni loading of 12.5% yields highest CH4 and CO2 conversions. Promoter introduction slightly suppresses low-temperature activity but substantially modifies support local structure and metal-support interface, improving NiO dispersion and increasing surface oxygen vacancies and active oxygen species (Oβ). These changes enhance CO2 adsorption-activation and suppress carbon deposition. After 20 h DRM, Ce-promoted catalyst shows smallest Ni particle growth (6.23→8.07 nm) and lowest carbon deposition, demonstrating superior stability and anti-coking capability. The study elucidates how Ce, La, and Zr enhance sintering and coking resistance via interfacial electronic modulation and improved oxygen storage/release, guiding rational design of stable Ni-based DRM catalysts.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608009
To investigate the flow and heat transfer characteristics of natural draft direct air-cooling towers (NDC) for large coal-fired power generating units, a three-dimensional CFD numerical model covering major plant buildings, air-cooled radiators, and ambient wind fields was established based on the NDC systems of a 2×660 MW unit of a power plant. The influences of meteorological factors, including ambient wind speed, ambient temperature, and ambient wind direction, as well as regulation measures such as rolling shutters, louvers, and bypass windows on the heat dissipation performance of NDC towers were systematically analyzed. The results demonstrate that ambient wind speed acts as the dominant factor governing the performance of the NDC system. As wind speed rose, the uneven distribution of air intake volume and heat dissipation among each cooling delta increased remarkably, which elevated the unit back pressure, and the upstream tower suffered more severe impacts than the downstream one. Ambient temperature exerted a slight effect on circumferential flow distribution, yet substantially changed the overall back pressure of the system. In terms of regulation strategies, closing rolling shutters in the windward zone and reducing the opening of partial louvers can improve air flow redistribution to a certain extent, but will reduce the total air flow rate and total heat dissipation of the entire tower. By contrast, bottom bypass windows can effectively optimize the air intake on the leeward side and boost heat dissipation under high-wind operating conditions, whereas top bypass windows deliver only limited improvement effects. This research can provide fundamental data and technical references for the optimal design, operational regulation, and energy-saving retrofitting of large NDC units.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608027
The relocation of numerous industrial enterprises in China has left behind soil contamination, particularly by volatile organic compounds such as BTEX, whose migration and health risks are of great concern. Coastal plains, characterized by high groundwater tables and interbedded sedimentary strata, exhibit contaminant distribution and migration patterns distinct from inland regions. This study investigated a decommissioned resin plant site in the Yangtze River Delta coastal plain, systematically analyzing the spatial distribution, migration, and health risks of soil BTEX. Seven BTEX compounds were detected with detection rates ranging from 24.3% to 47.1%. Maximum concentrations of benzene, ethylbenzene, and m/p-xylene exceeded China's Class I construction land screening values. The contaminant plume was predominantly located in the southern product warehouse area, while the potential source was traced to the upstream wastewater treatment unit, indicating a 'source-sink' spatial mismatch. Vertically, contaminants exhibited a 'shallow-layer volatilization, middle-layer enrichment, and deep-layer retardation' pattern, with significant enrichment in silty clay at 3–6 m depth and sharp concentration declines in mucky clay. Membrane Interface Probe (MIP) multi-parameter detection revealed that benzene and toluene migrated as a whole, whereas chlorobenzene lagged due to strong adsorption. Benzene posed the most significant health risk, with carcinogenic risk up to 7.42×10⁻⁴ and non-carcinogenic hazard quotient up to 38.24, both exceeding acceptable levels. Inhalation of indoor air contaminated by vapor intrusion from underlying soil contributed over 87% of benzene's total risk, dominating the exposure pathway. This study elucidates the unique migration and risk formation mechanisms under high water table and interbedded strata, providing a scientific basis for precise investigation, risk assessment, and remediation of similar contaminated sites.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4063-2
Quantum dot light-emitting diodes (QLEDs) are emerging as a leader in next-generation display technology. In principle, the efficiency of QLEDs is highly reliant on the radiative recombination rate of injected electrons and holes in the QD emissive layer. Within a solitary light-emitting cycle, a pre-negative-charged QD bursts into a fleeting sparkle upon encountering a hole, much like a lighted piston within a roaring engine. More pistons bring higher horsepower. The challenge of achieving highly efficient QLED lies in how to increase the number of pre-negatively charged QDs. To address these limitations, we developed a ZnO@ZnMgO core-shell nanoparticle (NP)-based electron transport layer (ETL). This design synergistically combines the high conductivity of ZnO core and the low defect density of the ZnMgO shell. Measured by electron-excited transient absorption, the average electron population (<N_e>) in the emissive layer for ZnO@ZnMgO and ZnMgO-based QLEDs was 0.61 and 0.33 at 4 V, respectively, which greatly increases the carrier recombination efficiency. As a result, green QLEDs achieve a peak EQE of 30.66%, maximum luminance of 1,615,039.85 cd/m2, and a low turn-on voltage of approximately 2 V. The T95 operational lifetime exceeded 29,000 h at 1,000 cd/m2. Currently, all parameters are at the top level within the QLED region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4004-3
The development of efficient and stable oxygen evolution reaction (OER) electrocatalysts is critical for clean energy technologies, yet conventional cobalt-based spinel catalysts often suffer from insufficient activity and structural instability under operating conditions. To address these challenges, this study proposes and constructs a cation-ordered spinel-like catalyst (HVI Metal-CoMoO4/NF). The unique crystalline framework induces significant Jahn-Teller distortion and pre-stabilizes a Co2+/Co3+ mixed-valence state at the cobalt active centers via asymmetric Co–O–Mo bridges, effectively optimizing bulk charge transport. Electrochemical tests demonstrate that its performance significantly surpasses that of benchmark materials, requiring only an overpotential of 307 mV to drive a current density of 100 mA cm−2 in 1.0 M KOH, with a Tafel slope of 63.13 mV dec−1, maintaining stable operation for over 320 h at high current density. Crucially, our structural and in situ characterization results clearly reveal a stable and well-crystallized reconstruction behavior from the surface into the bulk of the spinel-like pre-catalyst during the OER. This work fundamentally addresses the challenges of disordered reconstruction and unstable active phases in traditional spinel catalysts, providing a paradigm for regulating the dynamic evolution of electrocatalysts through precise structural design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3954-9
Tin (Sn)-based perovskite solar cells (TPSCs) are a leading candidate for next-generation photovoltaics due to their ideal optical bandgap, high carrier mobility, and excellent light absorption, yet their performance lags behind lead-based counterparts. The primary limitations include the inherent oxidation sensitivity of Sn2+ and rapid crystallization kinetics, as well as the reliance on fullerene-based electron transport layers (ETLs) such as ICBA and PCBM, which suffer from low electron mobility, weak interfacial interaction, high synthesis costs, and poor stability against moisture and light. These drawbacks impede charge extraction and transport, exacerbating interfacial non-radiative recombination. To address this, Liang and coworkers designed a novel series of non-fullerene polymer ETLs based on fluorinated tri-receptor polymers (P1, P2, and P3), featuring simplified synthesis, low cost, and strong structural tunability. Among these, P3-based devices achieved a power conversion efficiency (PCE) of 16.06% on 0.04 cm2 cells and maintained high performance on 1 cm2 cells, demonstrating significant breakthroughs in efficiency, stability, and large-area scaling. The non-fullerene ETLs exhibit enhanced electron mobility, improved energy-level alignment, and stronger interaction with the perovskite interface, effectively suppressing non-radiative recombination. This work provides a promising strategy to replace fullerene-based ETLs, advancing the commercial viability of TPSCs.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60662-7
Perovskite-type catalysts show promise for CO2 methanation, yet their low-temperature performance and mechanisms remain unclear. Here, a LaNiO3/CeO2 catalyst was synthesized via sol-gel and impregnation. In situ reduction decomposed the perovskite into highly dispersed Ni0 particles (average 12.6 nm) on CeO2, which provided abundant oxygen vacancies (Ce3+/(Ce3++Ce4+) = 9.2%) and weak/moderate basic sites. This synergy enhanced CO2 adsorption and activation. At 200–300 °C, the catalyst achieved ~100% CH4 selectivity and CO2 conversion up to 23.6% at 300 °C. Comparative studies with LaNiO3, LaCeNiO4, Ni/CeO2, and La-Ni/CeO2 revealed that the perovskite pre-structuration and in situ reduction optimize Ni dispersion and metal-support interactions, stabilizing Ni0 and tuning surface basicity and oxygen vacancies. This work provides a design strategy for efficient low-temperature CO2 methanation catalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4164-3
Lithium metal anodes (LMAs) are pivotal for next-generation high-energy batteries, yet their commercialization is hindered by dendrite growth and unstable solid electrolyte interphase (SEI). Here, we report a dual-layered artificial SEI (ASEI) comprising an inner LiF-rich inorganic layer and an outer perfluoropolyether (PFOE) organic layer, fabricated via a scalable roll-pressing technique. The LiF-rich layer lowers Li-ion diffusion barriers and provides mechanical robustness, while the PFOE layer chemically stabilizes the interface against electrolyte oxidation. Symmetric cells with PFOE-LiF@Li anodes achieve over 1400 h of stable cycling at 30 mA cm−2 and 5 mAh cm−2. Full cells paired with LiFePO4 cathodes deliver 350 cycles at 1 C and over 550 cycles at 2 C with high capacity retention and Coulombic efficiency. This work establishes a design principle for interfacial engineering, combining inorganic rigidity with organic functionality, and offers a promising route for practical LMBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4216-7
Flexible Cu2ZnSn(S,Se)4 (CZTSSe) solar cells are promising for lightweight and mechanically pliable photovoltaics, yet their performance is limited by severe non-radiative recombination and residual stress. Here, we report a sealed constant temperature (SCT) annealing strategy that simultaneously optimizes the CZTSSe/CdS heterojunction and alleviates stress. Under uniform mild thermal conditions (85°C, 5 h), SCT annealing promotes gradient diffusion of Cd2+ into the absorber, partially substituting Zn2+, which optimizes band alignment, passivates interface defects, and suppresses near-interface CuZn defects. This reduces open-circuit voltage loss and improves fill factor. The flexible device achieves a power conversion efficiency of 13.07%, a significant improvement over the reference (12.1%). The SCT strategy also enhances mechanical flexibility by reducing residual stress. Our findings provide a controllable route to advance both efficiency and flexibility of flexible CZTSSe solar cells.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3480-1
Electrochemical nitrate reduction to ammonia (NRA) offers a sustainable route for wastewater denitrification and decentralized ammonia synthesis, but its practical deployment is constrained by sluggish reaction kinetics and the competing hydrogen evolution reaction (HER). Monometallic Cu electrocatalysts, despite favorable nitrate adsorption and tunable electronic structure, exhibit weak H* adsorption, limiting the hydrogen radical-mediated pathway that suppresses HER at low overpotentials. Here, highly dispersed Cu/WO3 heterojunctions supported on carbon fiber were synthesized via carbothermal shock reduction, which reaches ultra-high temperatures within seconds and prevents active-site accumulation. The optimal Cu/WO3 heterojunction achieves an ammonia yield rate of 158.66 μmol h−1 cm−2 and a Faradaic efficiency of 98.27%. Electron paramagnetic resonance and density functional theory calculations reveal a synergistic mechanism: Cu sites preferentially adsorb NO3−, while adjacent WO3 sites accelerate water dissociation to generate hydrogen radicals (H*), which drive the continuous hydrogenation of nitrate to ammonia. This spatial separation of functions promotes the H*-mediated pathway and suppresses HER. The work establishes a heterojunction design strategy for non-precious-metal NRA electrocatalysts, enabling high-rate, high-selectivity ammonia production under mild conditions.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3510-0
The activity and stability of single-atom catalysts (SACs) are intimately associated with the structure of supports. Herein, by employing a van der Waals (vdW) heterostructure support, we construct a highly active and durable Pt SAC for hydrogen evolution reaction (HER). The unique support consists of monolayer MoS2 attaching on hierarchical N-doped carbon nanocages (hNCNC), on which Pt presents as individual single atoms on the hNCNC and as island-like single-atom layers on the MoS2. The optimized Pt1-MoS2/hNCNC demonstrates low overpotential (11 mV at 10 mA cm−2) and high mass activity (5.6 A mgPt−1 at −20 mV) in 0.5 M H2SO4 solution, outperforming commercial Pt/C. Impressively, the Pt1-MoS2/hNCNC exhibits improved long-term stability in proton exchange membrane water electrolyzer relative to commercial Pt/C. The excellent HER performance is attributed to the regulated electronic structure, robust interaction of Pt atoms with MoS2/hNCNC and facilitated charge transfer. This study establishes an innovative strategy to develop a highly active and durable Pt SAC using vdW heterostructure supports.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3631-1
Anion exchange membrane water electrolysis (AEMWE) offers cost and dynamic-response advantages over proton exchange membrane systems, yet commercial deployment is constrained by the alkaline stability of anion exchange membranes (AEMs) and the sluggish kinetics of non-precious metal catalysts. This work reports a series of poly(terphenyl-diphenylmethane piperidinium) (QPDPMTP) membranes synthesized with varied diphenylmethane (DPM) content. The alkyl chain of DPM induces pronounced microphase separation and elevates free volume fraction, yielding an OH− conductivity of 152 mS cm−1 at 80 °C for QPDPMTP-10. After 1032 h immersion in 6 M NaOH at 80 °C, the membrane retains 90.7% of its initial conductivity. An AEMWE cell integrating QPDPMTP-10 with a non-precious NiFeCo LDH/NiS/NF anode achieves 3.11 A cm−2 at 2 V in 1 M KOH at 80 °C and sustains 1 A cm−2 for 1800 h under gradient KOH concentration. These results establish a viable pathway for durable, low-cost AEMWE systems.