SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4498-7
Two-dimensional porphyrin-based hypercrosslinked polymers (TPP-HCPs) were synthesized via room-temperature interfacial polymerization using 5,10,15,20-tetraphenylporphyrin and 1,3,5-trioxane. The resulting TPP-HCPs exhibited a BET surface area of 548 m2 g-1 and a CO2 uptake of 7.97 wt% at 1 bar and 298 K. CuO/TPP-HCPs nanospheres were fabricated by thermal conversion of Cu(NO3)2·3H2O in DMF at 135 °C, using TPP-HCPs as dynamic templates. This in-situ strategy generated CuO nanoparticles within the conjugated porous matrix, facilitating electron transfer and enhancing CO2 access to catalytic centers. In CO2 electroreduction, the composite achieved a total gas Faradaic efficiency exceeding 90% at ~500 mA cm-2 (-1.4 V vs. RHE), with 40.9% for C2H4, 8.2% for CH4, 31.9% for CO, and 12.3% for H2. The catalyst maintained stability over 24 h in an H-cell. These results demonstrate that 2D conjugated polymer-templated catalysts can sustain high-rate CO2 conversion to value-added products, offering a viable route for industrial CO2 utilization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4425-4
Flexible and weavable alternating-current electroluminescent (ACEL) fiber devices are pivotal for wearable displays and human-computer interfaces, yet their intrinsic lack of color tunability restricts high-density information interaction. This study presents a dynamically color-tunable electroluminescent fiber device with a coaxial winding structure that integrates multiple fiber electrodes emitting the three primary colors. Through simple voltage driving, the device achieves a color gamut covering 131.07% of the sRGB standard, enabling arbitrary full-color tunability, including standard white light with CIE coordinates of (0.31, 0.33). The emission peak is continuously tunable over a 161.7 nm range, a 4-fold enhancement compared to previously reported ACEL fibers. The coaxial winding architecture is compatible with large-scale fabrication, yielding hundred-meter-scale fiber devices with a luminance variation of only 2.76%. The electroluminescent performance remains stable under stringent industrial standards: 10,000 friction cycles, 20 accelerated washing cycles, and 10-day storage at 105 °C and −20 °C. Integration into a smart textile watchband demonstrates real-time heart rate visualization via progress color changes and gesture-controlled color switching, validating its potential as an effective human-computer interface.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4395-x
Electrocatalysts in lithium–sulfur (Li–S) batteries accelerate sulfur species redox reactions and restrict polysulfide shuttling, yet ideal electrocatalysts with remarkable bidirectional catalytic effects remain scarce. This work utilizes iron (Fe) to trigger bidirectional catalytic effects in a cobalt (Co) electrocatalyst, generating a metal alloy-based heterostructure of Co-Co7Fe3 dispersed homogeneously on carbon sheets (Co-Co7Fe3/CS). Electrochemical tests and in situ X-ray diffraction disclose significantly enhanced bilateral catalytic activity of Co-Co7Fe3 compared to bare Co, confirmed by self-discharge measurements. Post-cycling investigation validates protection of the Li metal anode from sulfur species corrosion. The Co-Co7Fe3/CS-modified coin cells deliver an exceptional rate capability of 603 mAh g–1 at 5.0 C and steady long-life cycling for 500 cycles at 1.0 and 2.0 C. Under high sulfur loadings and lean electrolyte conditions, an impressive areal capacity with stable cycling is realized. This work provides valuable insights for designing metal alloy-based heterostructures as advanced electrocatalysts in Li–S batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4342-3
Electron acceptors containing single-bond-linked building blocks offer attractive advantages for organic solar cells owing to their synthetic simplicity and structural modularity. However, achieving backbone planarity without compromising electronic compatibility remains a persistent challenge. Conventional conformational locking strategies based on alkoxy substitution can effectively suppress torsional freedom but often elevate the highest occupied molecular orbital energy level, limiting compatibility with widely used donor polymers. Here, we report a partially fused electron acceptor design that achieves intrinsic backbone planarity through heterocycle selection rather than side-chain-assisted conformational locking. By incorporating a benzodifuran core and furan-thiophene linkages, the resulting acceptors exhibit a near-coplanar backbone geometry as revealed by density functional theory calculations, without the need for electronically perturbing alkoxy groups. Devices based on the optimized acceptor (BDF-1) deliver a binary power conversion efficiency of 12.2%, and further improvement to 19.5% is achieved in a ternary blend with PM6 and BTP-eC9. The enhanced performance is accompanied by favorable morphology, balanced charge transport, and suppressed recombination losses. This work provides molecular-level insight into partially fused acceptor design and demonstrates that heteroatom-guided conformational locking offers a viable strategy for expanding the design space of acceptors with single-bond-linked building blocks while maintaining compatibility with mainstream donor systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4359-0
Organic solar cells (OSCs) require cathode interlayers (CILs) that combine high charge transport, defect passivation, and thickness insensitivity for scalable manufacturing. Here, we report the synthesis of a novel A-D-A-A'-type polymer, PDPP2F-NDI-N, via the green and efficient direct arylation polymerization (DArP) method. The multiple electron-deficient units in the backbone confer strong electron-withdrawing character, effective work function modulation, enhanced built-in potential, high crystallinity, and ordered molecular packing. PDPP2F-NDI-N exhibits a high electron mobility of 1.01 × 10⁻³ cm² V⁻¹ s⁻¹ and electrical conductivity of 3.13 × 10⁻³ S m⁻¹, facilitating efficient charge extraction and transport. Its interfacial modification capability suppresses interfacial defects and reduces non-radiative recombination losses. In ternary OSCs, PDPP2F-NDI-N achieves a high power conversion efficiency (PCE) of 20.44%, with outstanding thickness insensitivity retaining 92.8% of peak PCE at a 30 nm CIL thickness, and a T80 lifetime exceeding 1700 hours under photo-thermal aging. This work demonstrates that poly(A-D-A-alt-A') backbone design combined with DArP synthesis provides an effective strategy for developing high-performance, thickness-insensitive, and stable polymeric CILs, advancing efficient, stable, and scalable OSC applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4381-5
Bismuth telluride (Bi2Te3)-based alloys remain the benchmark for low-temperature thermoelectric applications, yet their conversion efficiency is limited by the trade-off between electrical and thermal transport. This study introduces a pseudo grain boundary engineering strategy to simultaneously enhance the average figure of merit (ZT) in p-type (Bi,Sb)2Te3 (BST) materials. By incorporating Ag-based compounds, the carrier concentration is optimized via substitution of Ag+ ions, while the introduction of secondary phases at grain boundaries effectively suppresses lattice thermal conductivity. The approach yields a peak ZT of 1.35 at 393 K and an average ZT of 1.25 across 303–483 K, representing a significant improvement over pristine BST. Compared to prior reports, this work achieves superior average ZT while maintaining high electrical conductivity, addressing the longstanding bottleneck of thermal conductivity reduction without compromising carrier mobility. The findings underscore the efficacy of pseudo grain boundary engineering in advancing Bi2Te3-based thermoelectrics for solid-state cooling and power generation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4176-y
Three-photon microscopy (3PM) in the near-infrared-III (NIR-III) window (1600–1840 nm) enables high-resolution visualization of cerebral vasculature in vivo, but its imaging depth and quality are limited by the performance of fluorescent probes. Here, we report a probe optimization strategy transitioning from mirror symmetry to centrosymmetry, yielding a highly symmetric aggregation-induced emission (AIE) molecule, T4PQ. The centrosymmetric structure aligns donor-acceptor units, promoting uniform electron cloud delocalization and directional charge transfer, which enhances exciton formation and suppresses non-radiative decay, thereby increasing fluorescence quantum yield. This symmetry also boosts the three-photon absorption cross-section by enhancing electron delocalization and transition dipole moment, enabling stronger nonlinear optical responses under long-wavelength excitation. T4PQ nanoparticles (T4PQ NPs) exhibit an enhanced three-photon absorption cross-section, high fluorescence quantum yield, and excellent photostability. In murine models, T4PQ NPs achieved three-dimensional cerebrovascular imaging at a depth of 1785 μm and real-time hemodynamic observation in microvessels at 1006 μm depth, with good biocompatibility. These results validate the advantage of centrosymmetric molecular design for deep-brain imaging probes, offering a high-performance tool for neurovascular research.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4322-4
Ultrafast scintillators with low-nanosecond emission are essential for next-generation high-rate X-ray and particle imaging. Although Ce3+-activated scintillators inherently exhibit fast response characteristics, conventional Ce3+-doped hosts rarely achieve low-nanosecond ultrafast decay. Here, we report a high-entropy fluoride scintillator (HEFS), Ce:LaGdCaSrBaF12 (Ce:LGCSB), in the form of bulk single crystals. The severe lattice distortion arising from multi-cation disorder induces exciton localization and effectively suppresses exciton diffusion. Through the rapid relaxation of localized excitons, the high-entropy Ce:LGCSB single crystals deliver a decay time of 1.23 ns with a 94.6% fast-component contribution and without any noticeable slow component. Through first-principles calculations, spectroscopic characterization, and transient dynamics analysis, we reveal that the ultrafast response originates from accelerated Frenkel exciton (FE) recombination enabled by the high-entropy environment. This work establishes entropy-engineered fluorides as promising ultrafast scintillator platforms and proposes a general strategy for extending sluggish diffusion effects to the excitonic scale, offering new opportunities for improving scintillation timing performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3604-1
Piezoelectric materials convert mechanical energy into electrical signals, enabling applications in sensors, actuators, and energy harvesting. Inorganic ceramics like PZT and BTO exhibit excellent piezoelectric properties but are brittle, limiting their use in flexible electronics. This work presents a porous composite of PZT@carboxymethyl chitosan (CMCS) in thermoplastic polyurethane (TPU). The core-shell structure enhances interfacial compatibility, while the porous TPU skeleton facilitates stress transfer and amplification, allowing high piezoelectric content. The resulting PZT@CMCS/TPU devices achieve an output voltage of 53 V and current of 13 μA, an 11-fold improvement over conventional PZT composite films. This approach enables flexible piezoelectric devices with high performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3617-x
Macrophages are pivotal in infection resolution and tissue repair via dynamic M1-to-M2 phenotypic polarization. Although various nano-biomaterials can modulate macrophage polarization, achieving sequential M1-to-M2 transition using a single nanoformulation remains challenging. Here, we propose a strategy employing transition metal carbide/nitride (MXene) nanosheets, internalized by macrophages, as the sole regulator to induce sequential polarization. Under a rotating magnetic field, the high electrical conductivity and magnetoelectric activity of endocytosed MXene generate electrical signals and reactive oxygen species (ROS), driving M1 polarization. Upon magnetic field removal, the inherent bioactivity of MXene facilitates repolarization to the M2 phenotype. Mechanistically, this transition involves inhibition of the NF-κB signaling pathway and activation of the JAK-STAT signaling pathway. In vivo, MXene nanosheets under on-off rotating magnetic field stimulation enabled sequential M1-to-M2 polarization, promoting bacterial clearance and tissue regeneration in infected wounds. This two-step sequential strategy targeting macrophages offers a promising therapeutic approach for infected wound healing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3687-6
P2-Na0.67Ni0.33Mn0.67O2 (NNMO) is a promising cathode for sodium-ion batteries (SIBs) due to its high energy density and operating voltage. However, severe P2-O2 phase transition at high cut-off voltage causes large volume variation, structural degradation, and rapid capacity decay. Ion doping has been explored to suppress this transition, but achieving both high capacity and stability remains challenging. Here, we demonstrate that precise composition regulation enables both. The designed P2-Na0.67Ni0.28Mg0.03Fe0.04Mn0.55Ti0.1O2 retains high electrochemical active element content while effectively suppressing phase transition, leading to outstanding structural stability and fast charge transfer kinetics. This cathode delivers a high specific capacity of 143.5 mAh g−1 at 0.1 C and maintains stable cycling over 1000 cycles. Our work provides a new strategy for rationally designing high-capacity, stable cathode materials for SIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3714-3
Eco-friendly aqueous zinc batteries (AZBs) are promising alternatives to lead-acid batteries in applications requiring both safety and energy density. However, their practical deployment is hindered by the synergistic deterioration of zinc anodes—structural collapse and kinetic failure—under high depth of discharge (DOD) and high current densities, which severely limits actual energy and power densities. Here, we report a strategy for the in situ integration of a double-layer topological chitosan framework (D-CTS) on current collectors via regulating phase separation kinetics during multistage coordination-neutralization electrophoresis. The vertical through-hole array is formed by coupling instantaneous and delayed phase separation. Subsequently, a columnar zinc array is mediated by D-CTS to construct an integrated component (D-CTS-Zn) comprising a vertical through-hole separator and an array anode. The embedded interconnected nanonetworks within the through-hole walls enable dynamic equilibrium of the columnar zinc array through a lateral ion compensation mechanism. As a result, Zn||Zn symmetric cells with D-CTS-Zn stably cycle over 3000 cycles at 200 mA cm−2 under 60% DOD. The assembled D-CTS-Zn||MnO2 battery delivers an energy density of 83 Wh kg−1 at an ultrahigh power density of 9.25 kW kg−1. This work provides a constructive strategy for chitosan phase separation regulation and separator-induced reversible metal array anodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3695-8
Sulfur-based lithium-ion batteries, particularly those employing sulfurized poly(acrylonitrile) (SPAN) cathodes and graphite (Gr) anodes, offer high theoretical capacity and low cost but suffer from temperature-dependent capacity decay. This study systematically investigates the electrochemical dynamics and capacity decay mechanism of SPAN||Gr pouch cells cycled at 25–55 °C. Multiscale analyses reveal that capacity fade arises from active lithium loss and increased resistance, both accelerated by higher temperatures. Active lithium loss is primarily attributed to dead lithium formation and thickening of the solid electrolyte interphase (SEI) and cathode electrolyte interphase (CEI), while resistance increase is predominantly due to SEI/CEI thickening. As temperature rises, active lithium loss becomes the dominant decay factor. Leveraging the consistent decay mechanism across temperatures, an accelerated aging model based on the Arrhenius equation is developed: y = 0.9x + a. This model accurately predicts cycling parameters at specific temperatures and reduces testing time by 50% when extrapolating from 55 °C to 25 °C. These insights provide critical guidance for developing long-life sulfur-based batteries for practical energy storage applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3598-1
Embedding a dielectric layer between as-synthesized graphene nanoribbons (GNRs) and metal surfaces represents a powerful strategy to achieve electronic decoupling, thereby enabling the extraction of these ribbons' intrinsic electrical properties. Although several reports have documented dielectric intercalation between GNRs and metal substrates, studies on Ag(111) substrates are limited. Here, we demonstrate a semiconducting AgTe monolayer intercalation method to achieve electronic decoupling between as-synthesized GNRs and an Ag(111) substrate. Using low-temperature scanning tunneling microscopy, we directly observed the AgTe intercalation process at the GNR/Ag(111) interface. By combining scanning tunneling spectroscopy and density functional theory calculations, we elucidate the critical role of AgTe monolayer intercalation in reducing the interaction between as-synthesized GNRs and the Ag(111) substrate and observe the near-intrinsic electrical properties of the GNRs. Our findings offer a practical and effective strategy for intercalating AgTe monolayers between carbon-based nanomaterials and Ag(111) substrates, facilitating the unambiguous characterization of the near-intrinsic electronic properties of these materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3912-0
This erratum corrects an error in the Chinese name of co-first author Tianxiao Xiao (肖天孝) as originally published in the article 'A multi-modal smart chest patch for real-time cardiopulmonary monitoring and anomaly detection' (Sci China Mater, 2025, 68(12): 4413–4422). The corrected Chinese name is 肖天笑. The correction applies solely to the author's name and does not affect the scientific content, experimental data, or conclusions of the original paper. The authors and publisher apologize for any inconvenience caused.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506021
To elucidate the seasonal variation in cadmium (Cd) accumulation in ratoon rice and its relationship with root surface iron plaque, this study compared Cd concentrations in brown rice and the characteristics of iron plaque components (amorphous Fe, Am-Fe; crystalline Fe, Cry-Fe) between the main and ratoon crops of six rice varieties under different stubble heights. A field experiment was conducted in a Cd-contaminated paddy in Liuyang, Hunan (soil total Cd: 0.56 ± 0.06 mg·kg⁻¹). Ratoon crop treatments included low stubble (20 cm) and high stubble (60 cm). Brown rice Cd concentrations varied by variety, season, and stubble height. Low stubble generally increased brown rice Cd in the ratoon crop compared to high stubble; high stubble reduced Cd in most varieties relative to the main crop. Health risk assessment indicated that low stubble in the ratoon crop posed higher non-carcinogenic risk than the main crop and high stubble, while carcinogenic risks exceeded acceptable levels across all treatments. Iron plaque Am-Fe and Cry-Fe concentrations in the ratoon crop were generally lower than in the main crop, with Am-Fe consistently exceeding Cry-Fe. In the main crop, total Fe, Am-Fe, and Cry-Fe on root surfaces were significantly negatively correlated with brown rice Cd (P < 0.05), but correlations were not significant in the ratoon crop. High stubble reduced Cd accumulation and non-carcinogenic risk in most varieties, yet carcinogenic risk remained. Iron plaque significantly impeded Cd uptake in the main crop but its effect weakened in the ratoon crop. Selecting low-Cd-accumulating varieties and optimizing stubble height are key strategies for safe ratoon rice production in Cd-contaminated areas.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507055
The increasing complexity of pollutant sources in municipal wastewater networks, driven by unauthorized industrial discharges, poses significant risks to the stable operation of wastewater treatment plants. This study, conducted in an industrial park in Ningbo, Zhejiang Province, developed a source apportionment method using excitation-emission matrix (EEM) fluorescence spectroscopy combined with spectral angle mapping (SAM). A pollution fingerprint database was constructed from wastewater samples of six representative enterprises (A–F) and municipal sewer samples. The SAM algorithm demonstrated high sensitivity and stability in detecting changes in water composition, with spectral angle values showing a strong linear correlation (R² > 0.88) with the volume ratio of enterprise wastewater in mixed samples. This enabled both qualitative identification and quantitative estimation of pollution sources. Field application over a 12-hour monitoring period identified two enterprises as major contributors to organic matter and nitrogen during critical pollution episodes, consistent with trends in DOC, TN, and UV254. The proposed EEM+SAM approach offers a non-invasive, high-throughput method for real-time monitoring and source tracing of multi-source pollution in complex sewer systems, providing a scientific basis for pollution accountability and precise enforcement.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112104
Carboxyl-modified polystyrene microplastics (PS-COOH) are negatively charged particles formed by surface oxidation and functional group modification of polystyrene microplastics (PS), widely used in biomedical and analytical chemistry. However, studies on their neurotoxic effects on aquatic organisms are scarce. This study employed zebrafish (Danio rerio) as a model organism, exposing embryos to environmentally relevant concentrations (0.1, 1, 10, 100 μg·L−1) of PS and PS-COOH. Neurotoxic effects were assessed by measuring tail coiling frequency at 24 hpf and swimming velocity under alternating light/dark cycles at 120 hpf. Results demonstrated that both PS and PS-COOH induced neurotoxicity, with PS-COOH significantly reducing tail coiling frequency and average swimming speed compared to PS (P<0.05). Exposure to 10 μg·L−1 PS-COOH disrupted neurotransmitter homeostasis, altering levels of acetylcholine (ACh), serotonin (5-HT), and γ-aminobutyric acid (GABA). Transgenic zebrafish Tg(huc:EGFP) fluorescence assays revealed that PS-COOH (0.1–100 μg·L−1) caused damage to central neurons. These findings indicate that PS-COOH exposure impairs cholinergic, serotonergic, and GABAergic neurotransmission, induces neuronal damage, and exerts neurotoxic effects on zebrafish larvae. This study provides a theoretical basis for assessing the ecological and health risks of modified microplastics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3595-7
Cu(I) complexes exhibiting thermally activated delayed fluorescence (TADF) have emerged as promising alternatives to noble-metal-based emitters for organic light-emitting diodes (OLEDs). However, the development of red-emitting Cu(I) complexes has been hindered by slow radiative decay and fast nonradiative decay. In this study, a linear two-coordinate Cu(I) complex, ICuTMC, was designed and synthesized. By pairing a pyrazine-fused N-heterocyclic carbene and a tetra-methylcarbazolyl ligand, a strong ligand-to-ligand charge transfer excited state is generated. Single-crystal structure authenticates close intramolecular C–H···Cu contacts, providing good steric shielding to the metal center. C–H···π interactions between ligands are also revealed. The complex exhibits highly efficient red TADF with emission maximum at 622 nm, photoluminescence quantum yield of 76%, and short delayed fluorescence lifetime of 0.24 μs. This is enabled by a large oscillator strength from the coplanar donor-Cu-acceptor conformation, a small singlet-triplet energy gap from spatial separation of frontier molecular orbitals, and strong spin-orbit coupling from the metal center. Vacuum-deposited OLEDs based on ICuTMC achieve a peak external quantum efficiency of 25.9% and a significantly small roll-off of 1.9% at 10,000 cd m−2. These performances demonstrate a way to overcome the energy gap law for linear coinage metal complexes toward red OLEDs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3778-8
The global surge in polyvinyl chloride (PVC) waste demands urgent technological solutions that address both environmental persistence and resource recovery. Here, we present a triple-functionalization strategy that converts chlorinated plastic waste into high-performance sodium-ion battery anodes through molecular-level control of carbon architectures. Sequential dichlorination, sulfonation, and N-doping collaboratively reconfigure precursor reactivity, steering pyrolysis toward hierarchically porous hard carbon with tailored defect chemistry. Sulfonic groups stabilize 3D carbon skeletons during carbonization, enabling closed-pore formation with an average diameter of ~2.55 nm while N-doping expands interlayer spacing (0.382 nm) and creates adsorption-active pyrrolic-N sites. This defect-engineered synergy delivers unprecedented sodium storage metrics: 355 mAh g−1 reversible capacity at 0.1 A g−1 (95.4% of graphite’s Li-ion capacity), a capacity retention of 216 mAh g−1 after 1000 cycles at 1.0 A g−1 (70.1% capacity retention), and 188 mAh g−1 even at a high current density of 5.0 A g−1. Operando analyses reveal a potential-dependent storage hierarchy: surface-dominated adsorption transitions to intercalation/filling-dominated behavior with defect-buffered structural integrity. The process simultaneously achieves 25% carbon yield from PVC and avoids toxic dioxin emissions, establishing a scalable prototype for sustainable energy storage systems.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012404
Antibiotics, widely used for disease prevention and growth promotion in livestock, are emerging contaminants with potential risks to human health via the food chain. This review systematically analyzed the sources and residual levels of tetracycline (TCs) and β-lactam antibiotics in raw, pasteurized, commercial, and ultra-high-temperature (UHT) sterilized milk from various countries between 2012 and 2024, based on quantitative detection methods such as LC-MS and HPLC. The highest concentrations of TCs were found in milk from Algeria and Iran, while β-lactam residues were most elevated in Algeria, Bangladesh, and Kenya. The predominant TCs were tetracycline, chlortetracycline, and oxytetracycline; β-lactams were mainly penicillin and amoxicillin. Health risk assessment using hazard quotient (HQ) and hazard index (HI) revealed that all individual HQ values were below 1, indicating no significant non-carcinogenic risk from single antibiotics. However, the HI for multiple antibiotics in raw milk from Algeria exceeded 1, suggesting potential cumulative health risks. Furthermore, some studies reported residue concentrations surpassing maximum residue limits (MRLs), underscoring the need for continuous monitoring and control. This review highlights the global variability in antibiotic contamination and the importance of comprehensive risk assessment to safeguard public health.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010701
This study investigated the long-term effects of biochar application on physicochemical properties and microplastic accumulation in aeolian sandy soils, based on a field experiment established in 2014. After seven years of mulched cultivation, soil samples were collected from 0–30 cm and 30–60 cm depths. Biochar application significantly increased soil porosity and available nitrogen, phosphorus, and potassium contents, while reducing bulk density. At a biochar rate of 126.00 t·hm−2, soil water content was significantly reduced. Microplastic abundance averaged 3459.57 pieces·kg−1 in the 0–30 cm layer, with the highest abundance at 126.00 t·hm−2; in the 30–60 cm layer, average abundance was 3163.50 pieces·kg−1, with the highest at 63.00 t·hm−2. Microplastics were predominantly transparent, film-shaped, and 0–0.5 mm in size. The results indicate that biochar application significantly increased microplastic abundance in aeolian sandy soils, providing insights into microplastic adsorption and enrichment in agricultural ecosystems. Further research is needed to elucidate underlying mechanisms.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605011
Phytoplankton are highly sensitive to environmental changes and respond rapidly, making their community dynamics crucial early warning indicators of lake ecosystem health. Previous studies have qualitatively analyzed the combined effects of multiple physicochemical water quality factors on phytoplankton communities, but few have quantitatively distinguished direct from indirect effects. This study employed correlation analysis, redundancy analysis, and structural equation modeling to investigate the spatiotemporal distribution of phytoplankton communities in Baiyangdian Lake and their driving factors. A total of 113 species belonging to 57 genera and 7 phyla were recorded. Phytoplankton density exhibited significant seasonal and spatial variability, peaking in summer. Diatoms and green algae dominated in spring, transitioning to cyanobacterial dominance in summer and autumn, and reverting to green algae in winter. Structural equation modeling revealed that water temperature had a total positive effect on phytoplankton biomass (β = 0.96), comprising a direct positive effect (β = 0.94, P < 0.05) and an indirect positive effect via increased abundance (β = 0.02). Total nitrogen (TN) had a negative total effect on biomass (β = -0.98), with a direct negative effect (β = -0.97, P < 0.05) and an indirect negative effect via reduced abundance (β = -0.01). TN also negatively affected abundance (β = -0.15, P < 0.05). These findings provide a scientific basis for ecosystem health assessment, eutrophication control, and biodiversity protection in Baiyangdian Lake.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605010
The underwater light environment is a critical limiting factor for the colonization of submerged macrophytes and the ecological restoration of shallow lakes. Previous studies rarely quantified the contribution of aquatic environmental factors to the water quality–underwater light–macrophyte relationship, nor did they comprehensively consider factor correlations or establish thresholds for macrophyte colonization. This study, conducted in a typical national wetland nature reserve (Hongze Lake), measured photosynthetically active radiation, light attenuation coefficient (Kd), euphotic depth (Zeu), water transparency (SD), total suspended solids (TSS), chlorophyll-a (Chl-a), total nitrogen (TN), and total phosphorus (TP). A simulation model for Kd was developed, spatial distributions of environmental factors were analyzed, and contribution rates to light attenuation were quantified. Results showed that the mean Kd was 10.31±3.76 m⁻¹, and the mean Zeu (0.53±0.24 m) was lower than the mean water depth (0.94±0.29 m), with a spatial pattern of shallower Zeu in the west and deeper in the east. TSS and Chl-a were the primary direct influencing factors, while TN acted mainly indirectly. To achieve effective macrophyte colonization under average water depth conditions, thresholds were determined: Zeu ≥ 0.94 m, SD ≥ 0.41 m, Kd ≤ 4.95 m⁻¹, and Chl-a ≤ 3.8 μg/L. These findings provide quantitative guidance for lake restoration and water quality management.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605009
Reservoir CO2 emissions are a critical component of the global carbon cycle, yet existing prediction models often neglect reservoir size stratification, mixing data from large, medium, and small reservoirs. This study addresses this gap by constructing a training dataset exclusively for large and medium reservoirs in China and developing a neural network-based CO2 flux prediction model. The model revealed significant latitudinal zonation, with CO2 fluxes in southern low-latitude basins (e.g., Yangtze, Pearl) substantially higher than in northern high-latitude basins (e.g., Yellow, Songliao). Statistical analysis identified total phosphorus (TP) content as the strongest driver, exhibiting a positive exponential correlation with CO2 flux (p < 0.01). Reservoir age and latitude showed significant negative correlations, while physical parameters such as reservoir area, pre-impoundment submersion ratio, and average water depth showed no significant national-scale correlation. The study underscores the heterogeneity of dominant drivers across basins and proposes differentiated carbon mitigation strategies: for southern high-emission basins, controlling phosphorus inputs through wastewater treatment and restricting aquaculture; for northern basins, enhancing soil conservation to reduce carbon-rich sediment influx; and for new reservoirs, implementing vegetation clearance before impoundment and optimizing flood discharge schedules. These findings provide a theoretical basis for carbon emission characterization and support low-carbon management of large and medium reservoirs in China.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3742-5
Nematic liquid crystal elastomers (NLCEs) exhibit excellent mechanical properties and diverse deformation modes, while cholesteric liquid crystal elastomers (CLCEs) as photonic crystals (PCs) possess superior optical performance and intelligent response characteristics. Combining these two elastomers into a monolithic material is a challenging yet promising endeavor. Here, we designed and synthesized a new diselenide-bonded molecule (DSeAc), whose lower bond energy between selenium atoms endows it with excellent bond exchange ability. Consequently, two LCE matrices containing DSeAc molecules can achieve seamless bonding under mild conditions via dynamic diselenide bond exchange. By integrating a CLCE film and an NLCE actuator into a monolithic film, we enable the integration of two functional components, whose functional characteristics can be tailored as required. This function block combination strategy offers a promising pathway for developing smart materials with complex functions, showing great potential in information storage, anti-counterfeiting, and biomimetics.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509049
This study systematically compared three virus enrichment and concentration methods—polyethylene glycol (PEG) precipitation, aluminum salt coagulation, and centrifugal ultrafiltration—for detecting SARS-CoV-2 in high-turbidity, high-strength wastewater from inbound flights. The aluminum salt coagulation method exhibited the best overall performance, achieving an average recovery rate of 25.95% for SARS-CoV-2 pseudovirus, significantly higher than PEG precipitation (12.91%) and centrifugal ultrafiltration (0.22%) (P<0.05). Its detection limit reached 10 copies·mL⁻¹, whereas centrifugal ultrafiltration suffered severe membrane fouling, limiting detection to 1,000 copies·mL⁻¹. Considering the high pH buffering of flight wastewater, the aluminum salt method was optimized by adjusting pH to 6.00±0.4, employing rapid magnetic stirring, and reducing mixing time to 1 minute, yielding an average recovery of 27.56% (not significantly different from the original 25.95%, P>0.05). An automated enrichment device was developed based on the optimized method, reducing processing time per sample from 115 min to 60 min while maintaining comparable recovery and improved repeatability. Applied to 1,309 wastewater samples from inbound flights between January 2024 and May 2025, the average detection rate of SARS-CoV-2 was 45.45%, with trends consistent with national COVID-19 epidemiological data. The automated device demonstrates suitability for routine surveillance, providing technical support for port epidemic prevention.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60652-4
The performance of industrial zeolite catalysts, exemplified by fluid catalytic cracking (FCC) catalysts, is governed by microscopic behaviors including mass transfer, acidity, and coking. Conventional characterization techniques such as XRD, N2 physisorption, and TPD provide bulk-averaged or static ex situ information, failing to resolve dynamic processes under realistic reaction conditions. Recent advances in super-resolution fluorescence imaging enable nanoscale visualization of these key processes. This review systematically summarizes three critical applications: (1) Mass transfer diffusion: heterogeneous diffusion of reactant molecules within hierarchical pore networks is revealed, quantifying diffusion barriers and tortuosity. (2) Acid site accessibility: nanoscale localization of acid sites and their accessibility is achieved, correlating with catalytic activity. (3) Coking behavior: spatiotemporal evolution of coke species is identified, linking coke precursors to deactivation. The review elaborates how super-resolution imaging deepens understanding of fundamental catalytic mechanisms, providing theoretical support for rational design of high-performance catalysts through pore structure optimization, acid site regulation, and coking suppression. Current challenges and future directions are discussed, emphasizing the need for in situ correlation with catalytic performance.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606007
Cobalt-aluminum spinel metal oxides derived from hydrotalcite were synthesized via hydrothermal, coprecipitation, and sol-gel methods, and their catalytic performance for NO oxidation was systematically evaluated. Characterization by X-ray photoelectron spectroscopy (XPS), O2 temperature-programmed desorption (O2-TPD), H2 temperature-programmed reduction (H2-TPR), and Raman spectroscopy revealed that the synthesis method significantly influences the surface Co2+/Co3+ ratio, which in turn modulates the formation of surface oxygen vacancies. The hydrothermally synthesized catalyst (CoAlO-H) exhibited the highest density of surface oxygen vacancies, leading to enhanced adsorption and activation of gaseous oxygen and superior NO oxidation activity compared to coprecipitation (CoAlO-C) and sol-gel (CoAlO-S) counterparts. Mechanistic studies using NO-TPD, NO+O2-TPD, and in situ diffuse reflectance infrared Fourier transform spectroscopy (in situ DRIFTS) identified nitrates as key intermediates. Notably, CoAlO-C and CoAlO-S followed the Langmuir-Hinshelwood (L-H) mechanism, whereas CoAlO-H operated via both L-H and Mars-van Krevelen (MvK) mechanisms. The exceptional performance of CoAlO-H is attributed to its abundant surface oxygen vacancies, high surface oxygen mobility, and low decomposition temperature of reaction intermediates. These findings provide a rational basis for designing efficient non-precious metal catalysts for NO oxidation in diesel exhaust aftertreatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3963-5
Metal additive manufacturing (MAM) enables integrated one-piece fabrication of parts, high material utilization efficiency, and unparalleled design freedom. However, problems such as low production efficiency, difficulties in ensuring quality stability and defect control limit the large-scale industrial application of AM. In-situ active modulation for AM enables dynamic regulation of parts during the fabrication process, thereby enhancing the quality of the final fabricated parts without introducing extra processing steps. In-situ active regulation enables direct intervention during defect nucleation, providing better effectiveness than post-printing repairs while avoiding performance degradation risks associated with post-processing. Based on the difference of core factors directly affected during regulation, in-situ active regulation is categorized into the following. (1) Process and path parameter optimization, where regulation directly impacts manufacturing-related procedural rules. It is the simplest method of control and the preferred approach, with widespread attention focused on its effects on microstructure and mechanical properties. (2) Laser beam shaping, where regulation directly influences the energy carrier morphology. To address issues such as edge over-melting and localized energy deficiency caused by non-uniform energy distribution, laser beam shaping should be employed. (3) Additional physical field modulation achieved by superimposing supplementary physical fields. When optimal process and path parameters still fail to obtain the desired microstructure and mechanical properties, additional physical field control may be considered. Meanwhile, this work summarized the effects of different additional physical fields on the mechanical properties of various metallic base materials. The future trends of in-situ modulation in additive manufacturing are also discussed.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025102801
This study develops a multivariate time-series forecasting model for water quality in the Lhasa River, focusing on four key indicators: water temperature, pH, dissolved oxygen, and turbidity. Data preprocessing integrated multiple missing-value imputation strategies and interquartile range (IQR) outlier removal. Boxplots and relative standard deviation (RSD) assessed data distribution and dispersion, while autocorrelation and Pearson correlation analyses revealed periodic patterns and inter-variable relationships. Four representative algorithms—Support Vector Regression (SVR), Extreme Gradient Boosting (XGBoost), CNN-BiLSTM-Attention, and TCN-Transformer—were optimized via Bayesian hyperparameter tuning. Model performance was evaluated using MAE, MSE, RMSE, and R². The study systematically compared the effects of different missing-value handling methods, both independently and combined with IQR outlier removal. Results indicate that CNN-BiLSTM-Attention excels in water temperature prediction, suitable for relatively stable and simple patterns. In contrast, TCN-Transformer demonstrates superior performance for pH, dissolved oxygen, and turbidity, which exhibit strong nonlinearity and long-term dependencies, effectively capturing temporal dependencies and coupling relationships. The findings provide a viable technical route and theoretical reference for river water quality monitoring and intelligent early-warning systems.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025032001
This study investigates the variation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and their monomer components during low-temperature thermal decomposition (250–500 °C) of municipal solid waste incineration fly ash from a typical mechanical grate furnace. Results demonstrate that pyrolysis temperature and time significantly affect the solid-phase removal rates of PCDD/F mass concentration and toxic equivalent (TEQ) concentration. The influence weights of temperature on mass and TEQ removal rates are 20.86 and 21.41, respectively, while those of time are 4.27 and 3.36. Response surface analysis identifies optimal conditions at 380 °C for 1.0 h. At 250–300 °C, both PCDFs and PCDDs concentrations increase synchronously, indicating enhanced formation. At 300 °C for 2.0 h, high-chlorinated congeners undergo dechlorination to low-chlorinated ones, notably increasing 2,3,7,8-T4CDD (I-TEF=1.0) and 1,2,3,7,8-P5CDD (I-TEF=0.5). From 350 °C upward, significant degradation occurs; at 380 °C (1.0 h), degradation rates for PCDDs and PCDFs reach 97.8% and 97.6%, respectively, effectively reducing TEQ-contributing congeners. The process proceeds in two stages: initial dechlorination, followed by destruction of dioxin-like compounds at higher temperatures. 2,3,7,8-T4CDD emerges as a critical component for detoxification. These findings provide a scientific basis for optimizing thermal treatment of fly ash to minimize environmental and health risks.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025040104
The oxidative transformation of 2,6-dichlorophenol (2,6-DCP) was investigated in three typical zonal soils: black soil, red soil, and brown soil. Results demonstrated that 2,6-DCP underwent oxidative coupling in all soils, yielding hydroxylated polychlorinated diphenyl ethers (OH-PCDEs) and hydroxylated polychlorinated biphenyls (OH-PCBs) as primary products. The highest oxidative efficiency occurred in black soil, with approximately 85.1% of 2,6-DCP transformed within three days. In contrast, red and brown soils exhibited lower efficiencies, indicating a strong dependence on soil properties. Thermodynamic analysis revealed that the oxidative coupling reaction is endothermic, with elevated temperatures favoring reaction progress. Furthermore, soil microorganisms and dissolved oxygen were identified as critical controlling factors, acting synergistically to drive the reaction. This study provides the first evidence of natural oxidative coupling of 2,6-DCP in soil, forming OH-PCDEs and OH-PCBs. These findings offer significant scientific insight into the environmental fate of halogenated phenolic pollutants in terrestrial systems.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025032704
Chlorogenic acid (CGA), a key component of the anti-COVID drug Lianhua Qingwen, is recalcitrant to biodegradation and tends to bioaccumulate, posing risks to aquatic ecosystems. Conventional water treatment methods are inadequate for its removal. This study investigated the degradation of CGA using a magnetic field coupled Fe-C activated persulfate (MF/Fe-C/PS) advanced oxidation process. The degradation efficiencies of Fe-C, PS, Fe-C/PS, and MF/Fe-C/PS systems were compared, and the dominant reactive species and their contributions were identified. The effects of initial pH, persulfate (PS) concentration, Fe-C dosage, and inorganic anions on degradation kinetics were examined, along with the degradation pathway and disinfection byproduct (DBP) formation potential. Results showed that MF/Fe-C/PS achieved 99% degradation of CGA within 60 min under optimal conditions: pH=3, PS concentration 1.5 mmol·L−1, and Fe-C dosage 0.4 g·L−1. Coexisting Cl−, Br−, and I− inhibited CGA oxidation to varying degrees, as did natural organic matter (FA and BAS). The reactive species SO4−·, ·OH, and 1O2 contributed 41.6%, 30.5%, and 27.9%, respectively. Degradation mechanisms included hydrolysis, dehydroxylation, decarboxylation, and benzene ring cleavage. Pre-oxidation by MF/Fe-C/PS significantly reduced the DBP formation potential during subsequent chlorination/chloramination. Energy per order (EE/O) analysis indicated favorable economic efficiency.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3946-2
High energy-density lithium–sulfur (Li–S) batteries with rapid intermediate conversion and forbidden shuttle effect require superior electrocatalysts with tunable catalytic activity. In this protocol, binary FeNi3 alloy nanoparticles homogeneously embedded within carbon nanosheets (FeNi3/CNS) are synthesized to regulate the conversions of sulfur species. Time of flight-secondary mass ion spectroscopy reveals a significantly improved catalytic effect of binary FeNi3 alloy compared to bare Ni, which is confirmed by a larger Li2S amount generated during in situ X-ray diffraction measurement. Further anode characterization validates efficient shuttling suppression and good lithium metal protection. In Li–S batteries, electrochemical tests demonstrate a remarkable rate capability of 852 mAh g−1 at 3.0 C, and outstanding long-term cycle at 1.0 C (639 mAh g−1 after 500 cycles). Even under a wide operation temperature range (−15–60 °C), Li–S batteries exhibit stable cycling with high specific capacities under high current rates. Moreover, Li–S batteries using FeNi3/CNS attain a maximum areal capacity of 5.60 mAh cm−2 under ~4.0 mg cm−2 sulfur. This study highlights the advantages of adopting binary or multi-component metal alloys as electrocatalysts and points out the research directions to advance Li–S batteries into practical applications.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042103
This study investigated the spatiotemporal distribution, ecological risk, and sources of seven heavy metals (Cr, Cd, Cu, Ni, Pb, Zn, As) in surface sediments of Ranwu Lake, Xizang. Twelve samples were collected during the glacial ablation period (July 2024) and late glacial ablation period (November 2024). Concentrations were determined and analyzed using inverse distance weighting (IDW) for spatial patterns, geo-accumulation index (Igeo) and potential ecological risk index (RI) for risk assessment, and correlation analysis (CA), principal component analysis (PCA), and absolute principal component score-multiple linear regression (APCS-MLR) for source apportionment. Results showed that during glacial ablation, mean Cr, Cd, Pb, and As exceeded Xizang soil background values, while in the late ablation period only Cd, Pb, and As remained elevated. Spatial distribution varied between periods, with high concentrations in the middle and lower lake during ablation, shifting to the lower lake in the late period. Igeo and RI indicated overall low ecological risk, with Cd as the primary risk factor; mean RI values were 81.79 and 98.30 for the two periods, respectively. Source apportionment revealed that heavy metals mainly originated from natural and transportation sources, with traffic emissions being the major contributor to ecological risk. Specifically, Cr, Ni, and As were predominantly natural, Cd and Pb were mainly traffic-related, and Cu and Zn were influenced by both natural and traffic sources.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025051802
This study investigates the recovery of nitrogen and phosphorus from anaerobic digestion biogas slurry of chicken manure via magnesium-modified zeolite coupled with electrochemical precipitation crystallization. Three types of magnesium-modified zeolites were prepared using alkali activation and magnesium loading to enhance adsorption capacity. A coupled 'magnesium-modified zeolite-electrochemical MAP' reactor was constructed, and key parameters (N/P ratio, pH, current density) were optimized via response surface methodology. The results show that MgCl2-modified zeolite (MgCl2-ZO) exhibited the best coupling precipitation performance. Under optimal conditions (N/P ratio 3.78, pH 8.43, current density 13.11 A·m−2), the removal efficiencies for total nitrogen (TN), total ammonium nitrogen (TAN), total phosphorus (TP), and total phosphate (TPS) reached 54.84%, 62.93%, 82.02%, and 77.72%, respectively. The mechanism involves synergistic adsorption and electrochemical release of Mg2+ from the magnesium electrode, which promotes struvite crystallization. The electrochemical field enhances ion exchange and chemical precipitation on the zeolite surface, facilitating efficient nutrient recovery. This approach offers a promising solution for nutrient management in livestock wastewater.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3951-4
Silicon anodes offer an ultrahigh theoretical capacity (4200 mAh g−1) but suffer from >300% volumetric expansion during cycling and unstable solid electrolyte interphase (SEI) formation, leading to rapid capacity fading. Here, we design a hierarchical composite p-cSi@aSi@MgSiN2@C featuring a porous crystalline-amorphous silicon core (p-cSi@aSi), an in-situ MgSiN2 transition layer, and an outer nitrogen-doped carbon shell. The 3D interconnected pores accommodate volume expansion, while amorphous silicon enables isotropic lithiation-induced strain, eliminating crystalline phase transition barriers. The MgSiN2 layer transforms into a tough Li3N-rich SEI with ultra-fast ion channels, and the carbon shell provides mechanical confinement and electronic conductivity. This synergistic interface engineering achieves an initial coulombic efficiency (ICE) of 81.4%, a charge transfer resistance of 16.4 Ω after 200 cycles (64% reduction), and a Li+ diffusion coefficient of 1.72×10−11 cm2 s−1. The anode delivers 1719.3 mAh g−1 at 0.2 C after 200 cycles and 823.8 mAh g−1 at 0.5 C after 500 cycles. The molten salt electrolysis synthesis achieves a current efficiency of 68.12% and specific energy consumption of 12.76 kWh kg−1, with an estimated electricity cost of 1154.69 USD ton−1, only 20% of commercial Si/C anodes. This work resolves the ICE-cycle life trade-off and provides a scalable, cost-effective approach for next-generation high-energy batteries.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60708-6
Mercury emissions from coal combustion are highly toxic, volatile, and bioaccumulative, posing long-term threats to ecosystems and human health. This review systematically examines the current status and control policies of mercury emissions from coal combustion in China, analyzing distribution characteristics and transformation mechanisms during combustion, with emphasis on collaborative removal in pollution control devices after ultra-low emission retrofitting. A progressive strategy of 'synergistic enhancement–deep purification–resource recycling' is proposed, comprising three tiers: optimizing operational parameters of existing control systems to enhance synergistic mercury removal; developing efficient adsorption and catalytic oxidation technologies for industrial application; and advancing integrated mercury removal and recovery technologies, such as magnetosphere-based sorbents and recovery processes, focusing on high-value utilization. The paper also outlines future research directions aligned with international compliance and domestic environmental tax policies, providing theoretical and technical support for China's commitments to near-zero emissions of coal combustion pollutants.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4274-x
The escalating power density of electronic devices necessitates effective visible-light shielding in advanced packaging to ensure circuit security and long-term reliability. Photosensitive polyimides (PSPI) serve dual roles as photodefinable dielectrics and structural layers, but intrinsically black PSPI (B-PSPI) suffer from competitive ultraviolet (UV) absorption between chromophores and photosensitive moieties, limiting co-optimization of deep visible-light blocking and lithographic resolution. Here, we report a main-/side-chain spatial decoupling strategy to synthesize a novel B-PSPI. By polymerizing pyromellitic dianhydride with a main-chain coloring monomer (4,4'-diaminodiphenylamine) and a side-chain photosensitive monomer (1,4-dihydropyridine-functionalized diamine), the monomer stoichiometric ratio is precisely engineered. This design spatially isolates functional groups and enhances charge transfer, yielding exceptional visible-light shielding (CIE L* index of 21.39, cut-off wavelength ≈ 555 nm) with good lithographic sensitivity. UV exposure triggers in situ generation of coordination sites from photosensitive groups, anchoring active metal species for electroless copper plating. This enables direct additive fabrication of fine copper lines (40/80 μm line width/spacing) with robust Cu/B-PSPI interfacial adhesion of 16.6 MPa. This work provides a robust molecular design paradigm for B-PSPI, integrating superior optical shielding and surface metallization for high-density interconnect applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4222-9
The proliferation of high-frequency communication technologies has escalated electromagnetic (EM) pollution, posing risks to health and device reliability. Conventional microwave absorbers dissipate EM energy as heat, creating thermal management burdens and energy waste. This study introduces Bi2Se3 nanosheets, a topological insulator with surface conductivity and internal insulation, as a dual-functional material capable of both microwave absorption and thermoelectric conversion. Nanosheets with controlled morphology were synthesized via a polyol reduction method, with thickness and lateral size tuned by preparation conditions. The resulting composites exhibited excellent microwave absorption, achieving a broad absorption bandwidth of 2.95 GHz at sub-millimeter thickness. A multilayered structure design enabled full-band absorption from 2 to 18 GHz using a single absorbent. The Seebeck coefficient, derived from temperature differences up to 110 °C, was -152 μV/K, indicating efficient conversion of absorbed EM energy into electrical energy. This work demonstrates the potential of Bi2Se3 nanomaterials for self-powered electromagnetic devices, addressing both EM pollution and energy supply challenges.