SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4472-0
Dynamic electrocardiography (ECG) monitoring during physical activity remains compromised by motion artifacts that corrupt signal fidelity, particularly with conventional gel electrodes whose impedance rises sharply under deformation. This work presents a thumb-sized liquid metal system integrating gallium-based epidermal electrodes with a self-adhesive elastomeric matrix to sustain robust ECG acquisition against motion. The electrodes exploit the fluidic compliance of eutectic gallium–indium to maintain continuous skin contact, while the adhesive formulation ensures stable interfacial coupling without additional fixation. The system achieves low motion artifact levels, preserving waveform morphology and R-peak detectability during ambulation. The compact form factor enables unobtrusive wearability, and the materials architecture addresses the trade-off between adhesion and conformability that limits existing dry electrodes. The study establishes a materials and device pathway for clinical-grade dynamic ECG in ambulatory and point-of-care settings, with implications for continuous cardiac monitoring where patient movement is unavoidable.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4433-5
Negative thermal expansion (NTE) and zero thermal expansion (ZTE) materials are technologically relevant for precision engineering, yet their practical deployment is constrained by narrow operating temperature windows. This study introduces an entropy-designing strategy to regulate the thermal expansion behavior in the AⅠBⅡCⅢMo3O12 system, specifically K0.4(Mg0.25Mn0.25Co0.25Ni0.25)0.4Sc1.6Mo3O12 (CE0.4MO) and related CExMO compositions (x = 0.4, 0.6, 0.8, 1.0). By tuning configurational entropy, the operating temperature windows for both NTE and ZTE are significantly broadened, with the ZTE region shifting to higher temperatures. Among single-phase compositions, CE0.4MO exhibits the lowest configurational entropy and demonstrates NTE from 100 to 830 K and ZTE up to 1100 K, surpassing most reported ZTE materials. Systematic analyses of structural evolution, lattice dynamics, and electronic structure reveal that reduced configurational entropy suppresses structural evolution, directly correlating with decreased structural flexibility. Higher atomic displacement parameters (ADPs) of oxygen in CE1.0MO provide experimental evidence for enhanced flexibility. Raman spectroscopy shows that the full width at half maximum (FWHM) of peaks in the 750–900 cm-1 range positively correlates with configurational entropy, indicating reduced lattice disorder, while modes within 750–1050 cm-1 blue-shift as entropy decreases, confirming lattice stiffening. Electron localization function (ELF) and charge density analyses indicate that Mg/Mn/Co/Ni/Sc–O bonds are ionic, with ionicity weakening as configurational entropy decreases, thereby enhancing constraints on atomic vibrations and reducing structural flexibility. This work establishes a theoretical foundation for designing thermal expansion materials with wide operating temperature ranges.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4371-6
The sluggish kinetics of the oxygen reduction reaction (ORR) necessitates platinum-based catalysts, but their high cost and scarcity drive the search for platinum-group metal-free (PGM-free) alternatives. Fe−N−C catalysts with atomically dispersed Fe−N4 sites are promising, yet their practical performance is limited by buried active sites and poor mass transport. Here, a crumpled, multi-scale porous Fe−N−C catalyst (Fe−N−PCG) is synthesized via spray pyrolysis coupled with high-temperature metal etching. The crumpled morphology, formed by capillary compression during rapid solvent evaporation, and in-plane mesopores from Fe nanoparticle etching, synergistically enhance site accessibility and mass transport. Fe−N−PCG achieves a site density (SD) of 2.74×10^19 sites g−1 and Fe utilization (UFe) of 51.7%. As a gas diffusion electrode, it delivers a mass transport overpotential (ηmt) of 67 mV at 800 mA cm−2. In zinc-air batteries, Fe−N−PCG exhibits a peak power density of 296.1 mW cm−2 at 500 mA cm−2, outperforming Pt/C (241 mW cm−2 at 438 mA cm−2). At 50 mA cm−2, it delivers a discharge voltage of 1.19 V and a specific capacity of 815 mAh g−1, surpassing Pt/C (1.13 V, 715 mAh g−1). These results demonstrate that morphology and porosity engineering can concurrently optimize intrinsic activity, site utilization, and mass transport, offering a rational design strategy for high-performance PGM-free catalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4267-y
The synthesis of two-dimensional MBenes from MAB-phase ceramics is impeded by uncontrolled etching kinetics that compromise structural integrity and yield. This study introduces a vacuum molten salt strategy to regulate space-charge accumulation during the selective removal of Al from Mo2AlB2, producing honeycomb-like architectures. The vacuum environment suppresses oxidative side reactions and modulates ionic transport, enabling precise control over etching depth and morphology. The resulting Mo2AlB2 exhibits exceptional electromagnetic wave absorption, with a minimum reflection loss of -56.3 dB at 2.4 mm and an effective absorption bandwidth of 6.8 GHz. These metrics surpass conventional etching-derived MBenes by a factor of 2.5 in attenuation capacity. The space-charge-regulated mechanism is elucidated through in situ spectroscopic and computational analyses, revealing that vacancy-induced charge redistribution governs the etching front propagation. This work establishes a scalable route for high-purity MBenes with tailored porosity, addressing critical bottlenecks in energy absorption and catalytic applications. The vacuum molten salt approach eliminates the need for hazardous HF, offering a safer and more environmentally benign pathway for industrial translation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4383-8
Conventional cancer therapies remain constrained by undruggable oncogenic proteins and acquired resistance. Proteolysis targeting chimeras (PROTACs) have emerged as a transformative modality that harnesses the ubiquitin-proteasome system to selectively degrade target proteins, offering advantages over traditional small-molecule inhibitors. However, clinical translation of PROTACs is impeded by intrinsic physicochemical limitations: high molecular weight, poor bioavailability, and lack of tumor-specific delivery. Integrating PROTACs with nanotechnology has yielded advanced nano-PROTACs platforms. Nanocarriers enhance solubility and stability, optimize pharmacokinetics, and enable spatiotemporally controlled drug release through passive or active targeting. This review systematically summarizes recent advances in engineering multifunctional nano-PROTACs for cancer therapy, with particular emphasis on design strategies by which nanoengineering enhances PROTAC performance. We evaluate how these platforms improve anticancer efficacy and minimize systemic toxicity while exploring their therapeutic potential in monotherapy and synergistic treatment settings. Finally, we discuss current challenges and future perspectives, providing a theoretical and technical foundation for next-generation nano-PROTACs as a precise and potent strategy in precision oncology.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4416-8
Copper(I)-based carbene-metal-amide (CMA) emitters offer an earth-abundant alternative to precious-metal phosphors for organic light-emitting diodes (OLEDs), yet efficient green emission remains scarce due to limited π-extension and unbalanced charge-transfer characteristics of N-heterocyclic carbene (NHC) ligands. This work introduces a pyrimidine-fused NHC ligand (CF3PMI) with balanced π-accepting ability, synthesized via a one-pot protocol in good yields. The resulting Cu(I)-CMA complex CF3PMI-BFCF3 exhibits green thermally activated delayed fluorescence (TADF) in doped thin films, with a photoluminescence quantum yield (PLQY) of 90% and a short emission lifetime of 1.16 μs. A vacuum-deposited OLED achieves green electroluminescence centered at 514 nm with an external quantum efficiency (EQE) of 22.7%. Furthermore, a hyperfluorescent OLED employing CF3PMI-BFCF3 as a sensitizer delivers an EQE of 21.8%, green emission at 537 nm, and a narrow full width at half maximum (FWHM) of 30 nm. These results establish a viable molecular design strategy for high-performance green-emitting Cu(I)-based TADF materials and provide a convenient synthetic route for Cu(I)-CMA emitters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4342-3
Electron acceptors containing single-bond-linked building blocks offer attractive advantages for organic solar cells owing to their synthetic simplicity and structural modularity. However, achieving backbone planarity without compromising electronic compatibility remains a persistent challenge. Conventional conformational locking strategies based on alkoxy substitution can effectively suppress torsional freedom but often elevate the highest occupied molecular orbital energy level, limiting compatibility with widely used donor polymers. Here, we report a partially fused electron acceptor design that achieves intrinsic backbone planarity through heterocycle selection rather than side-chain-assisted conformational locking. By incorporating a benzodifuran core and furan-thiophene linkages, the resulting acceptors exhibit a near-coplanar backbone geometry as revealed by density functional theory calculations, without the need for electronically perturbing alkoxy groups. Devices based on the optimized acceptor (BDF-1) deliver a binary power conversion efficiency of 12.2%, and further improvement to 19.5% is achieved in a ternary blend with PM6 and BTP-eC9. The enhanced performance is accompanied by favorable morphology, balanced charge transport, and suppressed recombination losses. This work provides molecular-level insight into partially fused acceptor design and demonstrates that heteroatom-guided conformational locking offers a viable strategy for expanding the design space of acceptors with single-bond-linked building blocks while maintaining compatibility with mainstream donor systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4212-x
Idiopathic pulmonary fibrosis (IPF) is a lethal interstitial lung disease with limited therapeutic options. Current treatments, such as nintedanib and pirfenidone, target downstream fibrosis but fail to address the upstream drivers, including persistent alveolar epithelial injury and abnormal repair. This study presents an inhalable, reactive oxygen species (ROS)-responsive liposomal system (SAB/GC-1@Lip-cRGD) that co-delivers the antioxidant salvianolic acid B (SAB) and the thyroid hormone receptor β (TRβ) agonist Sobetirome (GC-1). The liposomes are surface-modified with cRGD peptides for targeted delivery to fibrotic lesions and possess a negative surface charge to enhance mucus penetration. In the high-ROS fibrotic microenvironment, the liposomes destabilize, releasing SAB and GC-1. SAB scavenges ROS to remodel the fibrotic niche, while GC-1 reactivates TRβ signaling, driving the differentiation of stalled Krt8+ transitional epithelial cells into functional alveolar type I (AT1) cells. In a mouse model of pulmonary fibrosis, SAB/GC-1@Lip-cRGD significantly reduced pro-inflammatory cytokines (TNF-α, IL-1β, IL-6) and TGF-β1 in bronchoalveolar lavage fluid and lung homogenates. The proportion of CD206+ M2 macrophages decreased from 27.4% in the model group to 6.2% after treatment, indicating potent anti-inflammatory and anti-fibrotic effects. This synergistic strategy of microenvironment remodeling and epithelial regeneration achieved robust collagen depletion, restoration of alveolar integrity, and recovery of pulmonary function, outperforming single-drug or non-targeted formulations. The work provides a generalized paradigm for integrating microenvironment regulation with regenerative repair in pulmonary diseases.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4176-y
Three-photon microscopy (3PM) in the near-infrared-III (NIR-III) window (1600–1840 nm) enables high-resolution visualization of cerebral vasculature in vivo, but its imaging depth and quality are limited by the performance of fluorescent probes. Here, we report a probe optimization strategy transitioning from mirror symmetry to centrosymmetry, yielding a highly symmetric aggregation-induced emission (AIE) molecule, T4PQ. The centrosymmetric structure aligns donor-acceptor units, promoting uniform electron cloud delocalization and directional charge transfer, which enhances exciton formation and suppresses non-radiative decay, thereby increasing fluorescence quantum yield. This symmetry also boosts the three-photon absorption cross-section by enhancing electron delocalization and transition dipole moment, enabling stronger nonlinear optical responses under long-wavelength excitation. T4PQ nanoparticles (T4PQ NPs) exhibit an enhanced three-photon absorption cross-section, high fluorescence quantum yield, and excellent photostability. In murine models, T4PQ NPs achieved three-dimensional cerebrovascular imaging at a depth of 1785 μm and real-time hemodynamic observation in microvessels at 1006 μm depth, with good biocompatibility. These results validate the advantage of centrosymmetric molecular design for deep-brain imaging probes, offering a high-performance tool for neurovascular research.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3608-8
Polymeric carbon nitride (PCN) is a promising photocatalyst for H2O2 production due to its visible-light response, low cost, and high selectivity for the two-electron oxygen reduction reaction (ORR). However, its H2O2 yield is limited by narrow light absorption, low charge separation efficiency, and insufficient active sites. Here, crystalline poly(heptazine imide) (PHI)-based carbon nitride with highly dispersed In sites and N defects was prepared via an ionothermal method using LiCl/KCl molten salts. The large π-conjugated system and N defects enhance visible-light harvesting. Remaining K+ ions in nitrogen cavities act as interlayer electron channels, while N defects induce asymmetric charge distribution on the heptazine network, promoting interlayer and in-plane charge separation and transfer. In sites accelerate charge transfer dynamics and serve as active sites for ORR. The synergistic effect of metal modification and defect engineering boosts electron delocalization, significantly improving photocatalytic activity. The H2O2 production rate of 10InPHI reaches 15.3 mmol g−1 h−1 via a two-step single-electron ORR pathway, underscoring the potential of modified carbon nitride for efficient H2O2 photosynthesis.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507032
To mitigate global warming, regional carbon neutrality pathways are critical. Based on the Guangdong Energy Policy Simulator (EPS) model, this study simulates total energy consumption and greenhouse gas (GHG) emissions under baseline, Carbon Neutral 60 (CN60), and Carbon Neutral 50 (CN50) scenarios, and analyzes the emission reduction effects and costs of various energy policies. Results show that by 2060, total energy consumption under CN60 and CN50 decreases by 39% and 44% relative to baseline, respectively. Primary electricity and other energy, natural gas, oil, and coal account for 56%, 26%, 14%, and 4% under CN60, and 60%, 24%, 13%, and 3% under CN50. GHG emissions under CN60 drop to 80×10^6 tCO2e by 2060, an 89% reduction from 2020; under CN50, emissions reach 92 and 55×10^6 tCO2e in 2050 and 2060, respectively, reductions of 87% and 92% from 2020. Policies such as increasing clean electricity share, industrial electrification (hydrogen), increasing green power purchases, building electrification, F-gas reduction, and improving industrial energy efficiency standards show significant reduction effects, with clean electricity share being the primary source. Policies like improving industrial energy efficiency standards, increasing industrial product utilization, and increasing clean energy vehicle market penetration are cost-effective; increasing clean electricity share, green power purchases, building electrification, and F-gas reduction effectively balance reduction effects and costs. Industrial electrification (hydrogen) contributes >5% cumulative reduction but faces economic challenges for full-scale promotion in the short term; industrial carbon capture and storage and electrolytic hydrogen contribute <2% cumulative reduction with high costs. Therefore, Guangdong should prioritize cost-effective policies, promote balanced policies, gradually optimize energy structure, achieve clean electricity, and foster green industrial transformation to achieve carbon neutrality at lower economic cost.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604001
This study systematically investigated the occurrence, spatial distribution, sources, and ecological risks of 160 pesticides in Dianchi Lake, a typical plateau lake impacted by agricultural activities. A total of 37 pesticides were detected in the water, with total concentrations ranging from 64.2 to 1132.8 ng/L (average 610.0 ng/L). Fungicides, including boscalid (BOS), fluopicolide (FPC), and dimethomorph (DMM), were dominant, contributing up to 65.0% of the total concentration. Spatially, the southern lake region exhibited significantly higher concentrations (672.5 ng/L) than the north, attributed to intensive facility agriculture. Highly hydrophobic pesticides, such as penconazole (PEN), showed a tendency to enrich in bottom layers. Source apportionment identified inflowing rivers and wastewater treatment plant effluents as primary input sources, with average concentrations 7 and 9 times higher than lake water, respectively. Ecological risk assessment revealed that pesticides posed the highest risk to algae, followed by daphnia and fish. Prometryn (PMT) was identified as a high-risk factor for algae, while profenofos (PFF) and carbendazim (CBD) posed potential threats to higher trophic levels. These findings provide fundamental data and technical support for understanding pesticide pollution in plateau lake ecosystems.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025111302
High-concentration chloride ions (Cl−) in industrial wastewater cause severe corrosion and environmental hazards. Conventional removal methods suffer from low efficiency, high cost, and difficulty in product recovery. This study fabricated porous metallic bismuth-based blocks (Bi-PM) via 3D printing, combining chemical precipitation with additive manufacturing. Systematic evaluation of Cl− removal under varying pH and light irradiation revealed that at pH 0.1 and 0.5, dark-condition efficiencies were 53.6% and 31.0%, respectively, increasing to 69.3% and 38.1% under light. Radical trapping identified photogenerated holes as the primary active species, oxidizing metallic Bi to release Bi3+ and enhance precipitation. At pH 0.5, Bi-PM exhibited balanced efficiency and structural stability; over five cycles, average removal efficiency was 25% in darkness versus 41.2% under light, with superior stability under illumination. XRD and SEM confirmed abundant BiOCl formation on the surface under light, mitigating Bi loss. This approach ensures high chloride removal while minimizing material degradation, offering a novel pathway for industrial wastewater treatment.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605022
Carbide slag (CS), an alkaline industrial solid waste from acetylene production in the chlor-alkali industry, poses severe ecological risks due to long-term stockpiling. This review systematically examines CO2 mineralization pathways and applications of CS, leveraging its high reactivity dominated by Ca(OH)2. Direct gas-solid and liquid-solid carbonation mechanisms, alongside indirect ammonium salt cyclic leaching-carbonation, are elaborated. Process optimization via parameter regulation, amino acid modification, and multi-solid waste coordination significantly enhances reaction efficiency and product performance, enabling controlled synthesis of high-value calcium carbonate. Environmental and economic analyses confirm that CS mineralization achieves CO2 fixation with good economic feasibility, simultaneously addressing solid waste resource utilization and carbon emission reduction. Derived lightweight fillers and low-carbon cementitious materials exhibit both environmental and economic potential, providing theoretical and application support for a 'waste-to-waste' carbon reduction technology system.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3936-8
The precise separation of enantiomers is essential for developing effective chiral drugs, yet conventional membranes are constrained by the ubiquitous selectivity-permeability trade-off and low flux, limiting scalable production of single-enantiomer drugs. Herein, we present a cascade reaction strategy integrating Sonogashira-Hagihara coupling and Friedel-Crafts alkylation to fabricate porous conjugated microporous polymer membranes (CCMP-M P1–4/SiO2). This approach enhances specific surface area by 400-fold compared to the product from the Sonogashira-Hagihara coupling reaction alone, creating interconnected porous networks that facilitate mass transport. This hypothesis was confirmed by pore-size gradient experiments, which revealed a critical size-matching effect: matched molecular dimensions enable high-speed mass transfer with 97% enantioselectivity, while mismatch reduces selectivity to 9%, as visualized in a separation performance matrix across four chiral molecules. Precise chiral recognition is programmable via absolute configuration control of chiral monomers, with the mechanism of “preferential adsorption–interfacial enrichment–promoted diffusion” confirmed by static adsorption and density functional theory calculations. This strategy achieves breakthrough performance: Naproxen flux reaches 37 mmol m−2 h−1, surpassing literature values, and enables membrane-based separation of Raceanisodamine (89% selectivity of 6S, 2′S and 6R, 2′R-isomer after cascade enrichment) for the first time. This work provides a new paradigm for designing high-performance chiral separation membranes, facilitating scalable and sustainable production of single-enantiomer drugs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3801-1
Traditional phase transition gel platforms face significant challenges in achieving time-gated information encryption and decryption. Here, we report a photocleavable gel that enables time-gated information encryption and decryption, enhancing information storage security. The gel is synthesized by copolymerization of hydrophobic ortho-nitrobenzyl acrylate (NA) and acrylamide. Upon ultraviolet (UV) irradiation, hydrophobic NA units partially cleave to yield orange-colored o-nitrosobenzaldehyde (NSBA) molecules and hydrophilic acrylic acid groups, altering local color and hydrophilicity. Information is spatially encoded using a photomask. The written information is encrypted by dissolving NSBA molecules in dimethyl sulfoxide (DMSO). Upon aqueous immersion, differential hydrophilicity between irradiated and non-irradiated zones triggers localized phase separation, facilitating decryption. Notably, photolysis kinetics is time-gated, ensuring decryption only within a specific time window in water. This method surpasses traditional gel constraints, offering a novel paradigm for secure information storage.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3742-5
Nematic liquid crystal elastomers (NLCEs) exhibit excellent mechanical properties and diverse deformation modes, while cholesteric liquid crystal elastomers (CLCEs) as photonic crystals (PCs) possess superior optical performance and intelligent response characteristics. Combining these two elastomers into a monolithic material is a challenging yet promising endeavor. Here, we designed and synthesized a new diselenide-bonded molecule (DSeAc), whose lower bond energy between selenium atoms endows it with excellent bond exchange ability. Consequently, two LCE matrices containing DSeAc molecules can achieve seamless bonding under mild conditions via dynamic diselenide bond exchange. By integrating a CLCE film and an NLCE actuator into a monolithic film, we enable the integration of two functional components, whose functional characteristics can be tailored as required. This function block combination strategy offers a promising pathway for developing smart materials with complex functions, showing great potential in information storage, anti-counterfeiting, and biomimetics.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508101
The emission of sulfur dioxide (SO2) and nitrogen oxides (NOx) from fossil fuel combustion and metal smelting industries poses severe risks to environmental and human health. This study utilized depleted lead-zinc molten slag as a desulfurizer for wet flue gas desulfurization, and the resulting desulfurization slurry was further employed for NOx removal, achieving resource utilization. The desulfurization efficiency of the slag was determined, and NaClO2 was identified as the most effective oxidant when combined with the slag slurry for NOx removal. The effects of NaClO2 concentration, reaction temperature, flue gas flow rate, oxygen concentration, NOx concentration, and pH on removal efficiency were investigated. Optimal conditions were found at NaClO2 concentration of 2.5 mmol·L−1, temperature 45 °C, flue gas flow 200 mL·min−1, O2 volume fraction 10%, NOx volume fraction 0.03%, and pH 6, achieving a NOx removal efficiency of 97.24%. Metal ion experiments revealed that Fe3+, Zn2+, Mn2+, and K+ exhibited synergistic effects with NaClO2, with Fe3+ showing the most significant enhancement. Fe3+ promoted the decomposition of NaClO2 to generate stronger oxidants such as ClO2, thereby enhancing NOx oxidation and absorption. This approach offers a cost-effective and environmentally friendly alternative to traditional selective catalytic reduction, avoiding ammonia slip and secondary pollution.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606013
The A2/O-MBR process, owing to its superior effluent quality and smaller footprint, is increasingly adopted in newly built and upgraded wastewater treatment plants. However, systematic studies on its greenhouse gas (GHG) emissions remain scarce, and direct comparisons with the conventional A2/O process are lacking. In this study, two full-scale wastewater treatment plants employing the A2/O and A2/O-MBR processes under identical influent conditions, climate, and discharge standards were investigated. A high-frequency monitoring system covering the entire treatment train was established, and combined with measurements of dissolved CH4 and N2O, water quality parameters, and operational parameters, to elucidate the differences in GHG emission characteristics. Results showed that the daily average CH4 emission intensities were not significantly different between the two plants [(0.67 ± 0.22) and (0.65 ± 0.18) g/m3, respectively]. CH4 emissions mainly originated from sewer-derived anaerobic production and subsequent release in the pretreatment units (accounting for over 70% of the total emissions), with partial in-plant oxidation by methanotrophs. Temperature and aeration-induced stripping were identified as key driving factors, as CH4 emissions were positively correlated with ambient temperature and dissolved oxygen (DO). In contrast, more than 90% of N2O emissions occurred in the biological treatment units. The A2/O-MBR plant exhibited significantly higher daily N2O emission intensity [(0.132 ± 0.055) g/m3] than the A2/O plant [(0.060 ± 0.046) g/m3], largely due to intensive aeration and oxygen-enriched internal/external recirculation in the membrane tank, which enhanced N2O production and stripping. Correlation analysis further revealed that N2O emissions in the A2/O plant were positively related to influent COD and BOD5, indicating dominance of heterotrophic denitrification, whereas in the A2/O-MBR process they were mainly driven by NH3-N loading and DO, reflecting a nitrification-based pathway. Importantly, both processes exhibited CH4 and N2O emission factors that were significantly lower than the reference values recommended by the IPCC and industry guidelines, underscoring the necessity of localizing emission factors for accurate carbon accounting.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3870-9
High-purity (HP) alloys are critical for next-generation technologies requiring extreme reliability, yet trace impurities at parts-per-million levels can severely degrade mechanical properties, corrosion resistance, and long-term stability. This review comprehensively examines recent advances in HP alloy development, covering purification approaches, processing strategies, and performance optimization. It details how trace impurities influence microstructural evolution and material properties, and discusses techniques for achieving ultralow impurity levels, including vacuum melting, zone refining, and chemical vapor deposition. The review highlights impurity sensitivity across major alloy systems—such as aluminum, titanium, zirconium, copper, and steels—and summarizes strategies to mitigate impurity-induced degradation, including advanced alloy design, grain refinement, and surface treatments. Advanced characterization techniques for detecting and quantifying impurities are also outlined. The review emphasizes the essential role of HP alloys in advanced structural and functional materials, and identifies key challenges and future directions, including the need for standardized purity definitions and cost-effective purification methods. This synthesis provides a roadmap for researchers and engineers aiming to harness the full potential of high-purity alloys in demanding applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3858-8
High-quality β-Ga2O3 membranes are pivotal for fabricating high-performance memristive devices. Here, vertical Ag/β-Ga2O3/Pt memristors built on high-crystalline-quality β-Ga2O3 membranes via lattice epitaxy engineering and a sacrificial-layer-assisted exfoliation strategy are reported. The resulting β-Ga2O3-based device demonstrates a high ON/OFF ratio exceeding 10^8, low SET/RESET voltages of 0.13 V/−0.11 V, low programming current of 10^-10 A, stable data retention beyond 4 × 10^4 s, and excellent subthreshold characteristics of ~0.47 mV/dec. Adjustable compliance current enables the coexistence of volatile and non-volatile switching modes. Additionally, the resistive switching versatility is predominantly governed by the migration of Ag ions, as supported by electrical characterizations and first-principles calculations. Furthermore, a β-Ga2O3 memristor-based circuit that functions as a reconfigurable and non-volatile exclusive OR (XOR) logic gate has been designed and simulated, enabling both image encryption/decryption and edge detection. This work not only demonstrates lattice-engineered, high-quality β-Ga2O3 membranes for fabricating advanced memristors but also extends their applicability to digital logic and reconfigurable image processing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4140-9
Metal covalent organic frameworks (MCOFs) are promising photocatalysts for carbon dioxide reduction reaction (CO2RR). However, the synthesis of ketimine-linked COFs remains challenging due to the low reactivity of ketones. Here, we report a straightforward strategy to construct diketimine-linked MCOFs via the condensation of acenaphthenequinone (Ace) with 1,3,6,8-tetra(4-aminophenyl)pyrene (TAPPy). The metal-free COF (TACOF-AA) exhibits AA stacking, while the addition of NiCl2·6H2O under identical conditions yields an AB-stacked Ni-based MCOF (Ni-TACOF-AB). The coordinated Ni species serve as active sites for CO2RR and enhance electron-hole separation. Photocatalytic tests demonstrate that Ni-TACOF-AB achieves a CO evolution rate of 11.71 mmol g−1 h−1 with 99.9% selectivity, which is 7.6 times higher than that of TACOF-AA. Density functional theory (DFT) calculations reveal that Ni-TACOF-AB lowers the activation energy barrier of the rate-determining step by regulating local charge distribution, facilitating electron transfer to adsorbed CO2. This work provides a novel approach for synthesizing ketimine-based COFs and highlights the importance of interlayer stacking in modulating photocatalytic performance.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607006
This study evaluates the global warming potential (GWP) of three typical air pollution control device (APCD) configurations in municipal solid waste (MSW) incineration under ultra-low emission standards. The configurations are APCD1 (SNCR+SDS+DS+ACI+FF), APCD2 (SNCR+SDS+DS+ACI+FF+SCR+WS), and APCD3 (SNCR+SDS+DS+ACI+FF+WS+SCR). Life cycle assessment (LCA) was applied to quantify GWP. Results indicate that APCD3 exhibits the highest GWP due to increased electricity consumption, yet it achieves the lowest pollutant emissions among the three. APCD1 shows the highest NOx emissions, contributing significantly to GWP, and requires technological upgrades. APCD2 consumes more resources but does not proportionally reduce emissions, suggesting inefficiencies. Electricity consumption is the dominant factor influencing GWP across all processes; reducing electricity use and improving energy efficiency are critical for mitigating environmental impact. The study recommends further research on CO2 reduction strategies and adoption of more efficient DeNOx technologies to align MSW incineration with ultra-low emission and low-carbon goals.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3920-1
Lead-free halide perovskites are promising scintillators due to strong X-ray attenuation and high internal quantum efficiency (IQE), but their application is hindered by moisture sensitivity. Here, CsSrCl3:Eu2+ nanocrystals were grown in situ in a specially designed inorganic glass matrix. By employing [PO4]-modification and controlled crystallization, a transparent CsSrCl3:Eu2+ glass-ceramic (GC) scintillator was obtained, combining high crystallinity (15.9%) with excellent optical transparency (85.3% at 432 nm). The GC exhibits outstanding photoluminescence (PL) performance, including a high IQE of 87.6% and superior thermal stability (74% intensity retention at 493 K relative to 303 K). Benefiting from the robust glass matrix, the GC retains 99% of its initial PL intensity after 14 days of water immersion. Under X-ray excitation, it shows blue X-ray excited luminescence (XEL), with peak and integrated intensities reaching 117% and 25.1% of those of Bi4Ge3O12 crystal, respectively. The scintillator achieves a high spatial resolution of 20 lp mm−1 and an X-ray detection limit of 3.7 μGy s−1. Furthermore, it demonstrates exceptional operational stability in humid environments, maintaining clear X-ray image contrast even after 48 h of water submersion. This study provides an effective strategy for stabilizing hygroscopic halide scintillators in a durable [PO4]-modified fluoroaluminate glass matrix and demonstrates the potential of CsSrCl3:Eu2+ GC for high-resolution and stable X-ray imaging.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508006
Landfill leachate, characterized by high ammonia nitrogen, high organic load, complex toxic components, and low nitrogen removal efficiency, poses significant environmental challenges. To achieve efficient nitrogen removal, a continuous-flow two-stage anoxic/oxic (A/O) moving-bed biofilm reactor (MBBR) system coupled with anaerobic ammonium oxidation (Anammox) was constructed and operated for long-term treatment of actual landfill leachate. After biofilm attachment and multi-gradient acclimation, influent concentrations were gradually increased from low levels (NH4+-N ~200 mg·L−1, COD ~2500–3000 mg·L−1) to high levels (NH4+-N ~1800 mg·L−1, COD ~8500 mg·L−1). During stable operation, average removal efficiencies of NH4+-N and COD reached 97.7% and 66.8%, respectively, with total nitrogen (TN) removal efficiency improving to 93.9%. Along the reactor, the first A/O stage achieved major organic degradation and ammonia oxidation, while the second stage facilitated nitrite accumulation and promoted Anammox for synergistic nitrogen removal. High-throughput sequencing revealed Proteobacteria as the dominant phylum (>50%), with denitrifying genera such as Azoarcus and Thauera significantly enriched. Planctomycetota abundance increased from 0.6% to 3.7%, and Candidatus Kuenenia was detected, confirming successful Anammox colonization and participation in nitrogen removal. This study validates the efficient combined nitrogen removal mechanism of the A/O–MBBR system with Anammox, providing theoretical basis and technical support for engineering treatment of high-ammonia wastewater.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511050
Municipal solid waste (MSW) management in Inner Mongolia has long relied on landfilling, facing land scarcity and leachate management challenges. This study addresses the region's dry, cold climate, high proportion of agricultural and livestock waste, fluctuating moisture content, and weak leachate treatment capacity. An engineering optimization was implemented on an 80 t·d−1 vertical rotary gasification-incineration system featuring a dual-combustion-chamber design (primary chamber for medium-temperature pyrolysis-gasification at 550–650 °C and secondary chamber for high-temperature oxidation above 900 °C), coupled with in-situ leachate recirculation. Field measurements showed improved processing capacity and continuous operation stability. Under the project's leachate yield, in-situ recirculation achieved on-site disposal without significant adverse effects on gasification-incineration conditions, providing buffering against moisture fluctuations. During the monitoring period, major gaseous pollutant emissions remained below current national standards. The results provide engineering references for the co-processing and stable operation of small-scale county-level MSW treatment facilities.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2026.JFCT.0003
Phosphorus and transition metal-modified ZSM-5 zeolites were prepared via incipient wetness impregnation and characterized by XRD, N2 adsorption-desorption, and pyridine-IR spectroscopy. The effects of modified zeolites on catalytic pyrolysis of n-heptane, 3-methylhexane, and methylcyclohexane were systematically investigated, revealing the structure-activity relationship between acid properties and catalytic performance. Results indicate that phosphorus and transition metal modification can regulate the L/B acid ratio of ZSM-5, which significantly influences product distribution. An excessively high L/B acid ratio promotes hydrogen and coke formation, leading to pore blockage and reduced conversion, whereas an appropriate L/B acid ratio facilitates mild dehydrogenation, enhancing ethylene and propylene yields. Reactant conversion followed the order: n-heptane > 3-methylhexane > methylcyclohexane. Efficient conversion of 3-methylhexane and methylcyclohexane requires catalysts with high L acid amount, strong Brønsted acid amount, optimized L/B acid ratio, as well as high specific surface area and micropore specific surface area. This study provides critical insights for designing high-efficiency alkane pyrolysis catalysts.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042702
This study estimated initial volume mixing ratios of volatile organic compounds (VOCs) in Dalian from June 1 to August 31, 2024, using a photochemical age-based parameterization method, and performed source apportionment with positive matrix factorization (PMF). Observed average TVOCs concentration was 12.49×10⁻⁹, comprising alkanes (84.2%), alkenes (10.4%), and aromatics (5.4%). Corrected initial TVOCs was 14.93×10⁻⁹, indicating a loss rate of 16.4%. Loss rates were highest for alkenes (53.2%), followed by aromatics (23.3%) and alkanes (6.8%). Ozone formation potential (OFP) averaged 21.31×10⁻⁹ (observed) and 38.75×10⁻⁹ (initial), with an OFP loss rate of 45.0%, distributed as alkenes (56.4%), aromatics (32.7%), and alkanes (10.3%). During ozone pollution episodes, TVOCs chemical loss was 1.9 times that of non-pollution periods, with alkene loss reaching 61.6%; OFP loss was 1.2 times higher, with alkenes contributing 88.4% to TVOCs loss. Secondary organic aerosol (SOA) formation potential from 08:00–17:00 was 1.51×10⁻¹ μg·m⁻³, with 99.4% from aromatics and toluene contributing 68.3%. PMF identified five sources: motor vehicles (49.6%), oil and gas volatilization (20.7%), petrochemical enterprises (12.6%), industrial processes (11.2%), and solvent use (5.9%). OFP modeling indicated motor vehicles contributed most to ozone formation (41.1%), followed by petrochemical enterprises (35.8%). During ozone pollution, PMF based on initial concentrations showed petrochemical sources had the highest OFP contribution (42.5%), whereas observed concentrations indicated motor vehicles as the top contributor (42.5%). This discrepancy underscores the necessity of correcting for photochemical losses in source apportionment studies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4035-5
Electrocatalytic CO2 reduction reaction (CO2RR) to formate offers a promising pathway for storing renewable electricity in chemical fuels and enabling carbon recycling. The development of efficient and stable catalysts for this specific pathway, however, remains a central challenge. Heteroatom doping can significantly tune the interaction between active sites and key intermediates, boosting catalytic performance. Conventional doping in Bi-based catalysts often relies on uncontrollable in-situ electrochemical processes, leading to ineffective bulk incorporation. Here, we present a simple pre-doping strategy that enables precise doping at surface active sites, thereby enhancing electrochemical performance. The resulting catalyst achieves >95% Faradaic efficiency for formate across 100–500 mA cm−2 in a flow cell and maintains >95% efficiency for over 70 h at 100 mA cm−2 in a membrane electrode assembly, outperforming pure Bi and Bi2S3. A solar-driven system further demonstrates a 4.4% solar-to-formate conversion efficiency. Mechanistic studies reveal that sulfur doping increases electron density, stabilizes the key *OCHO intermediate, and suppresses hydrogen evolution. These findings provide valuable insights into the precise pre-doping modulation of surface active sites for designing highly efficient and stable CO2RR catalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4047-0
The proliferation of electronic devices has exacerbated electromagnetic pollution, necessitating advanced electromagnetic wave (EMW) absorbing materials. In this study, VS2 nanorods were uniformly grafted onto graphene nanosheets (GNSs) via a facile ball milling method, constructing 1D/2D hierarchical VS2@GNSs composites with superior EMW absorption properties. The minimal reflection loss (RLmin) reached -49.83 dB at a thickness of 1.83 mm, while an ultra-broad effective absorption bandwidth (EAB) of 6.72 GHz was achieved at 1.96 mm. These performances are attributed to enhanced impedance matching and EMW attenuation capacities. Computer simulation technology (CST) full-wave simulations confirmed remarkable radar cross-section (RCS) suppression, with a reduction value of up to 20.38 dB m2 compared to a metallic substrate. This work provides theoretical and experimental guidance for designing high-performance stealth materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4037-1
Nasopharyngeal carcinoma (NPC) poses a therapeutic challenge due to its anatomical complexity and the limitations of conventional treatments in achieving precise targeting and sufficient efficacy. Here, we report a multifunctional platform based on heat-triggered electrospray self-healing porous poly(lactic-co-glycolic acid) (PLGA) microspheres encapsulating indocyanine green (ICG), sequentially coated with a tannic acid-Fe3+ (TAF) metal-phenolic network and fibronectin (FN) for targeted photothermal/chemodynamic combination therapy. The resulting functional microspheres (PI-TAF@FN) exhibit an average size of 1.9 μm, excellent colloidal stability, heat-induced self-healing performance, and a high photothermal conversion efficiency of 51.4%. These microspheres specifically target NPC cells via FN-mediated integrin recognition, enabling ICG/TAF-mediated photothermal therapy under 808-nm laser irradiation and TAF-mediated chemodynamic therapy, leading to enhanced cancer cell apoptosis in vitro. In a mouse NPC model, the combined photothermo-chemodynamic therapy achieved effective tumor treatment with minimal systemic toxicity. Furthermore, the dual TAF and ICG components allow multimode FN-targeted T1-weighted magnetic resonance/fluorescence/thermal imaging for precision NPC management. This electrospray self-healing porous microsphere platform offers a unique theranostic strategy that can integrate diverse therapeutic and diagnostic components for precision oncology.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3535-8
The brain's selective visual attention mechanism (SVAM) enables robust visual recognition in noisy environments through diverse neural action potential peaks acting as filters. Spiking neural networks (SNNs) mimic this paradigm but limited noise immunity and high write current density hinder brain-like efficiency. Hardware implementing SVAM necessitates spiking spintronic devices with noise-resistant and low operation current densities; such devices remain unreported. Here, we report an orbit-torque (OT) actuated ferromagnetic spiking synapse and neuron featuring a tunable peak action potential. These are more akin to biological neurons with varying sensitivities to external sensory stimuli, thereby augmenting the perception aptitude of the system in complex surroundings. Capitalizing on the high-efficiency OT, the ferromagnetic device demands a write current density of 5 × 10^6 A/cm^2, which is an order of magnitude lower than other spiking devices actuated by spin-orbit torque. Leveraging these neuromorphic devices, an all-spin SNN with low current density and tunable action potential peak has been fabricated, successfully mimicking the SVAM. In complex noise environment, the SNN achieves 92% on Cifar-10 and 95% on MNIST dataset, surpassing state-of-the-art spin-based SNNs by 5%. Our work provides a promising avenue for exploring the SVAM-inspired spiking neuromorphic devices, enhancing the bionic performance of the SNNs.