SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4412-y
GeTe-based thermoelectric materials are promising lead-free alternatives to PbTe, but their intrinsically high Ge vacancy concentration (~10^21 cm^-3) leads to excessive carrier density and degraded Seebeck coefficient. This study integrates resonant levels (RLs) via In doping and local van der Waals gaps via Sb/Bi alloying to decouple electron and phonon transport. The optimal composition Ge0.91Sb0.04Bi0.04In0.01Te exhibits a Seebeck coefficient of ~287.31 μV K^-1 at 323 K, more than double that of the In-free sample (~102.28 μV K^-1). The peak figure of merit zT reaches ~1.8 at 723 K, with an average zT of ~1.0 over 323–723 K. Vickers hardness is enhanced to ~224 HV, a ~93% improvement over pristine GeTe (~116 HV). X-ray diffraction reveals a structural evolution toward a pseudo-cubic phase with increasing In content, and the (202) peak shifts to lower angles, indicating lattice expansion. These results demonstrate that synergistic RLs and van der Waals gaps effectively optimize carrier concentration and suppress thermal conductivity, offering a viable route for high-performance, mechanically robust GeTe thermoelectrics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4494-9
Superionic conductors exhibit high cation mobility arising from weak binding and continuous transport pathways, atomistically characterized by extensive structural disorder and partial occupancy akin to amorphization. This disorder, whether confined to a cation sublattice or extended to full amorphization, strongly impedes lattice thermal transport, rendering these materials intrinsically ideal thermal insulators. This work investigates Ag26I18W4O16, a superionic conductor tunable from fully amorphous to single-crystalline states, as a model system to probe the impact of disorder and amorphization on thermal transport. Extensive Ag+ disorder, in both crystalline and amorphous phases, reduces thermal conductivity to approximately the theoretical lower bound of 0.16 W/m-K with virtually no temperature dependence, while concurrently achieving the lowest mean sound velocity ever recorded for a dense solid. Pair distribution function (PDF) analysis of synchrotron X-ray total scattering data indicates that short-range disorder (< 5 Å), rather than long-range periodicity, governs thermal insulation performance in both phases. These findings suggest a design strategy reconciling structural stability with glass-like thermal insulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4313-7
Liquid-to-vapor mass transfer is central to energy and environmental processes. Conventional distillation relies on vapor-liquid equilibrium and device-level optimization, with materials playing passive structural roles. Non-boiling processes such as membrane distillation and interfacial solar evaporation localize phase change at confined interfaces, making mass transfer a materials-mediated transport phenomenon where interfacial structure and chemistry dictate evaporation kinetics, vapor escape, and solute rejection. Janus interface materials, featuring spatially separated hydrophilic and hydrophobic domains, introduce architectural asymmetry to regulate liquid-to-vapor mass transfer. This review summarizes recent advances, highlighting mechanisms including the cooperative pump-valve effect, nanoconfinement-enhanced transport, and mitigation of fouling and scaling. Representative applications in membrane distillation, solar-driven evaporation, and personal thermal-moisture management are systematically discussed. Key challenges and future opportunities are outlined, particularly in advancing fundamental understanding, scalable fabrication, and practical implementation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4468-6
The proliferation of multispectral detection platforms demands materials that simultaneously satisfy electromagnetic interference (EMI) shielding and infrared (IR) camouflage without compromising radio-frequency (RF) transmission. Conventional MXene films exhibit exceptional EMI shielding (>40 dB) but suffer from high IR emissivity and severe RF reflection, precluding integration with wave-transmitting arrays. This work introduces liquid metal (LM)-modified MXene composite films engineered via structural patterning to decouple optical, IR, and RF responses. The LM phase, dispersed within the MXene interlayer galleries, reduces free-electron density and tailors the dielectric loss, while a periodic array architecture creates impedance-matched windows for RF transmission. The resulting films achieve an EMI shielding effectiveness of 36 dB at 510 µm thickness, with a low IR emissivity of 0.36 and an RF transmittance exceeding 80% in the X-band. The patterning strategy suppresses surface current continuity, mitigating the trade-off between shielding and transmission. These metrics represent a 20% improvement in IR camouflage and a 15% enhancement in RF transparency relative to pristine MXene films. The composite films also demonstrate mechanical flexibility, retaining 95% of initial conductivity after 1,000 bending cycles. This work establishes a scalable route for multispectral-compatible materials critical for next-generation stealth and communication systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4238-2
Infrared nonlinear optical (IR NLO) materials are critical for laser frequency conversion, yet their performance is often constrained by a trade-off between second harmonic generation (SHG) efficiency and laser-induced damage threshold (LIDT). Here, we report a new ternary diamond-like compound, AlGaS3, which successfully balances these competing demands. AlGaS3 crystallizes in a noncentrosymmetric structure composed of wide HOMO-LUMO gap [AlS4] tetrahedra and NLO-active [GaS4] tetrahedra. The compound exhibits a wide experimental optical band gap of approximately 3.38 eV, which is significantly larger than that of the benchmark AgGaS2 (AGS, ~2.70 eV). This wide band gap contributes to a high laser-induced damage threshold (LIDT) of approximately 6.0 times that of AGS, as determined by powder-based measurements. Notably, AlGaS3 also demonstrates a phase-matching SHG response of approximately 0.5 times that of AGS at a fundamental wavelength of 2.09 μm, with particle size-dependent behavior confirming phase-matchability. The combination of wide band gap, high LIDT, and moderate SHG response positions AlGaS3 as a promising candidate for high-power IR NLO applications. This work provides a viable strategy for designing IR NLO materials with enhanced laser damage resistance by incorporating wide-gap tetrahedral units.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4339-7
Neuromorphic computing demands energy-efficient synaptic devices that emulate biological plasticity. Optoelectronic memristors based on colloidal quantum dots (QDs) offer tunable bandgaps and solution processability, yet suffer from defect-mediated nonradiative recombination and instability. Here, we report ZnS-passivated CdZnSe core/shell QDs as the active layer in memristive devices, achieving enhanced synaptic emulation and information encryption. Time-resolved photoluminescence (TRPL) decay curves were fitted with a tri-exponential function, revealing that ZnS passivation suppresses defect-related trap states, prolonging the average carrier lifetime from 12.3 ns (CdZnSe) to 28.7 ns (CdZnSe/ZnS). The intensity proportion of the fast decay component (τ1 ≈ 1.2 ns) decreased from 45% to 18%, indicating reduced surface trapping. Devices incorporating CdZnSe/ZnS QDs exhibit stable bipolar resistive switching with an ON/OFF ratio exceeding 10^3, endurance of >10^3 cycles, and retention of >10^4 s. Under 365 nm UV illumination, the devices show light-tunable synaptic plasticity, including paired-pulse facilitation (PPF) with a facilitation index of 180% at a 50 ms interval, and transition from short-term to long-term memory. The memristors successfully emulate essential synaptic functions and are employed in a simple encryption scheme, demonstrating the potential of defect-passivated QDs for secure neuromorphic hardware.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4367-4
Single-crystalline Cs3Cu2I5 has attracted considerable interest owing to its excellent scintillation performance and favorable stability. Nevertheless, second phases induced by peritectic reactions during melt growth give rise to deteriorated scintillation properties and promote crystal cracking. In this work, the effects of non-stoichiometric ratios of raw material (n(CsI)=0.57, 0.62, and 0.63) on the crystallization behavior and scintillation properties were systematically investigated. The results show that the crystal quality is optimal at n(CsI)=0.62, featuring high transparency, absence of macroscopic inclusions, and cracking free, with a PLQY of 79.3%. Temperature-dependent photoluminescence verifies the self-trapped exciton emission mechanism with strong exciton-phonon coupling, giving an exciton binding energy of 473.9 meV and a Huang-Rhys factor S of 79.8. The as-grown crystal exhibits an optimized light yield of 24,380 photons/MeV, an energy resolution of 3.8% for 137Cs (662 keV) γ-rays, a dominant decay time of 957 ns, and excellent linear response in the medium-to-high energy region. Precise regulation of the raw material stoichiometry can effectively suppress the formation of second phases, yielding high-quality Cs3Cu2I5 single crystals whose comprehensive performance demonstrates promising application potential in γ-ray detection.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4317-4
This correction addresses an image assembly error identified in Fig. 7a of the original article published in Science China Materials, volume 66, issue 6, 2023, pages 2513–2522. The error was confined to the assembly of images in Fig. 7a, which presents H&E staining analysis of major organs from a toxicity study. The corrected version of Fig. 7 is provided in this corrigendum. The original study evaluated the toxicity of lyophilized cabazitaxel (CTX) and Tween 80-based CTX formulations in CD-1 mice following a single intravenous administration of 30 mg kg−1 CTX via the tail vein on day 0, with sacrifice on day 14 for analysis (n=5). The figure includes H&E staining of major organs, complete blood count (CBC) analysis with statistical significance indicated by *p < 0.05, and mouse weight measurements. The correction does not affect the overall results, data interpretation, or scientific conclusions of the original article. All authors have reviewed and approved the content of this corrigendum. The authors sincerely apologize for any inconvenience caused to the editorial office, reviewers, and readers. The article was received on 6 May 2026, accepted on 4 June 2026, and published online on 31 July 2026.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4197-4
Deep-blue organic light-emitting diodes (OLEDs) remain the most challenging primary-color emitters due to stringent exciton energy requirements. We strategically designed two innovative deep-blue emitters, SCZ-4AnCN and STPA-4AnCN, via systematic functionalization of an anthracene core with arylamino-decorated spirofluorene donors and cyano-substituted phenyl acceptors. Comprehensive theoretical and experimental analyses demonstrate that these spirofluorene-anthracene hybrids adopt precisely engineered distorted configurations, effectively suppressing detrimental intermolecular π–π stacking in condensed phases. The sp3-hybridized bridgehead carbons in spirofluorene units play a pivotal role by simultaneously restricting π-conjugation extension and fine-tuning donor–acceptor interactions, thereby stabilizing the lowest excited singlet (S1) state with dominant local excitation (LE) character. This molecular engineering yields exceptional deep-blue emission with remarkable efficiency. Notably, the materials exhibit unique high-lying reverse intersystem crossing (hRISC) behavior, enabling efficient triplet harvesting. Optimized doped devices incorporating SCZ-4AnCN achieve outstanding performance, including a maximum external quantum efficiency (EQE_max) exceeding 10% and CIE coordinates (0.154, 0.052) approaching the BT.2020 blue standard. Nondoped devices maintain impressive performance with an EQE_max of 7.51% and superior operational stability, demonstrating less than 10% efficiency roll-off at 1000 cd m−2. This work validates anthracene-based molecular architectures for deep-blue electroluminescence and establishes a transformative design paradigm for next-generation OLED emitters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3553-7
Gesture interaction has emerged as a highly effective interface for intelligent human-computer interaction, attributed to its intuitive interaction modality and multi-dimensional control capabilities. However, traditional gesture interaction devices often depend on predefined encoding rules, which substantially limit interaction efficiency and degrade user experience. This study introduces an innovative intelligent finger ring interaction system based on a triboelectric nanogenerator utilizing PDMS/SrTiO3 composite thin film (PS-TENG). The system maps freehand writing gestures directly to textual information input, thereby eliminating the need for complex gesture encoding schemes and offering a user-friendly, low-learning-curve input method. By integrating a deep learning model, the system achieves recognition accuracies of 98.21% for English letters, 96.87% for Arabic numerals, and 96.44% for Chinese characters. Furthermore, it supports secure and encrypted data transmission and enables wireless interaction for gaming control. These findings indicate that the intelligent finger ring interaction system possesses significant potential for practical applications in information input and wireless control.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3623-y
Organic light-emitting diodes (OLEDs) are an advanced technology for full-color displays, yet the low efficiency of blue OLEDs remains a critical bottleneck. Here, we report a new strategy to design robust Pt(II) emitters with enhanced molecular rigidity and increased locally excited character. The resulting Pt(II) emitter exhibits an extremely narrow emission spectrum peaking at 458.6 nm with a full-width at half-maximum (FWHM) of 16.0 nm and a small Huang-Rhys factor of 0.278, together with a high photoluminescence quantum efficiency of 95%. When doped into an OLED, the device emits at 464 nm with high color purity (FWHM = 19 nm) and achieves high external quantum efficiencies (EQEs) of 32.6%, 29.4%, and 26.9% at luminances of 123, 1000, and 5000 cd/m2, respectively. Notably, the device attains a record-high maximum brightness of 84,895 cd/m2 among reported deep-blue OLEDs with Commission Internationale de l'Éclairage (CIE) y-coordinate < 0.15. This work demonstrates one of the highest-performing deep-blue OLEDs reported to date, addressing the dual challenges of efficiency and brightness in this spectral region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3677-9
The demand for high-performance scintillators in high-temperature applications, such as industrial flaw detection and oil exploration, necessitates materials with both high efficiency and thermal robustness. This work reports Tb3+-doped oxyfluoride glass scintillators exhibiting anti-thermal-quenching radioluminescence (RL). Three synergistic strategies were employed: (i) an oxyfluoride glass host providing a low-phonon-energy environment, (ii) increased structural densification of the glass network, and (iii) thermally enhanced energy transfer from Ce3+ to Tb3+. The resulting scintillators achieve an optical transmittance exceeding 88% at 542 nm, a record RL intensity of 350% relative to a standard Bi4Ge3O12 (BGO) crystal, and an imaging resolution of 24 lp mm−1. Notably, the RL intensity at 633 K reaches 143% of its room-temperature (303 K) value, demonstrating significant anti-thermal-quenching behavior. In contrast, commercial BGO and CsI:Tl scintillators exhibit RL intensities dropping to approximately 1% under identical conditions. These results establish the potential of Tb3+-doped glass scintillators for high-temperature X-ray imaging and provide a strategic framework for developing thermally robust scintillating materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3706-3
Aprotic lithium-oxygen (Li-O2) batteries are severely limited by slow cathode reaction kinetics and large polarization. Herein, we design and prepare a Mott-Schottky catalyst by uniformly embedding ultrafine Ru nanoparticles on nitrogen-doped carbon (Ru@NC) nanoflakes to accelerate oxygen redox kinetics of Li-O2 batteries. The Mott-Schottky effect of Ru@NC drives spontaneous electron rearrangement in the NC matrix and induces a strong built-in electric field at heterointerfaces, which accelerates the activation and conversion of oxygen intermediates. The obtained Ru@NC possesses rich Mott-Schottky heterointerfaces and defective carbon structures, which provide extensive adsorption and nucleation sites. More importantly, Ru@NC manifests moderate affinity for the intermediate LiO2, inducing formation of unique nanosheet-like Li2O2 with low Li2O2/cathode interfacial impedance, which further enhances oxidation kinetics. These enable the Li-O2 battery with Ru@NC to deliver a remarkably reduced polarization of 0.89 V, superior rate performance, and prolonged lifespan of over 200 cycles. This work will provide valuable guidelines for engineering advanced electrocatalysts for high-performance Li-O2 batteries and beyond.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3713-y
Layered double hydroxides (LDHs) are promising electrocatalysts for the oxygen evolution reaction (OER), yet their practical application remains limited by poor electrical conductivity and sluggish reaction kinetics. In this work, we synthesize three high-entropy LDHs (HELDHs) featuring a hierarchical architecture of microspheres assembled from ultrathin nanosheets, via a simple hydrothermal method using a combination of low-cost, catalytically active transition metals (Fe, Co, Ni, Mn, Zn, Cu, and Cr). Among them, the FeCoNiMnZn HELDH exhibits outstanding OER performance, requiring an overpotential of only 306 mV to reach a current density of 100 mA cm−2. Notably, during 200 h of continuous operation, the device exhibits a stable and, in some cases, increasing current output. This exceptional activity is attributed to the formation of abundant cation vacancies, induced by Zn leaching, which enhance the intrinsic catalytic properties by optimizing the adsorption energies of key OER intermediates. Density functional theory calculations further validate that these vacancies modulate the electronic structure and lower reaction barriers, underscoring the effectiveness of cation-vacancy engineering in high-entropy systems for efficient and durable water oxidation catalysis. The optimized catalyst was further evaluated as the air cathode in a zinc–air battery, demonstrating practical electrochemical performance.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112804
The rapid dissemination of antibiotic resistance genes (ARGs) in aquatic environments poses serious threats to public health and environmental safety under the 'One Health' framework. Nanoplastics (NPs), as co-occurring pollutants, can exacerbate ARG risks by promoting horizontal gene transfer (HGT), yet the influence of different functional groups on extracellular ARG (eARG) transformation remains unclear. This study investigated the effects of carboxy-modified polystyrene NPs (PS-COOH) and amino-functionalized polystyrene NPs (PS-NH2) compared to unmodified polystyrene NPs (PS) on the transformation of the extracellular resistance plasmid IE-V1955 (carrying an ampicillin resistance gene) into Escherichia coli DH5α. Results showed that PS-COOH exposure promoted plasmid transformation similarly to PS, with effects increasing over 0.1–20 mg·L−1. Low concentrations (0.1–0.5 mg·L−1) of PS-NH2 also enhanced transformation, with stronger effects than PS-COOH at equal doses, whereas high concentrations (1–20 mg·L−1) inhibited it. Mechanistically, PS-COOH (0.1–20 mg·L−1) and low PS-NH2 induced intracellular reactive oxygen species (ROS), increased cell membrane permeability, elevated the protein-to-polysaccharide ratio in extracellular polymeric substances (EPS), and promoted biofilm formation, thereby facilitating transformation. High PS-NH2 concentrations caused excessive ROS leading to cell lysis and formed aggregates with plasmids larger than membrane pores, blocking uptake. These findings provide a theoretical basis for assessing the combined environmental health risks of NPs and ARGs.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024122101
Bicarbonate and carbonate ions (HCO3−/CO3^2−) are ubiquitous in wastewater and readily scavenge strong oxidants, leading to the formation of carbonate radicals (CO3·−) in radical-based advanced oxidation processes. This study investigated the influence of HCO3−/CO3^2− on the degradation kinetics of sulfamethazine (SMR) in a UV/TiO2 system. The presence of HCO3−/CO3^2− enhanced the degradation rate of SMR by sixfold compared to UV/TiO2 alone. Radical quenching experiments identified CO3·− as the primary reactive species responsible for the enhanced degradation, with hydroxyl radicals (·OH) also contributing. To quantitatively delineate the roles of reactive species and account for water matrix effects, a kinetic model was constructed using Kintecus software. The model accurately predicted SMR degradation over time and the contributions of individual radicals, demonstrating good predictive capability. Application of the model to real wastewater predicted that CO3·− is the dominant radical responsible for SMR degradation. These findings highlight the critical role of carbonate radicals in UV/TiO2 processes and provide a robust modeling framework for predicting the fate of pharmaceuticals in carbonate-rich waters.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024120203
Potassium permanganate (KMnO4) oxidation is a promising technology for organic pollutant removal in water due to its low cost and broad pH applicability. However, its moderate oxidation capacity results in slow degradation rates for refractory organic compounds. Carbon materials (CMs), known for their accessibility, stability, and environmental compatibility, have shown great potential in enhancing KMnO4 oxidation. This paper provides a comprehensive review of recent advancements on the enhancement of KMnO4 oxidation of organic pollutants by CMs. The performance and suitability of various CMs in improving KMnO4 oxidation were systematically compared. Additionally, two key mechanisms driving the degradation of organic pollutants in the KMnO4/CMs system were elucidated, along with a discussion on the recycling and regeneration of CMs. Finally, future research directions and development trends for this technology were outlined, aiming to offer insights to advance the practical application of KMnO4/CMs system in water treatment.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024120701
Surface waters contain numerous photoactive substances and low molecular weight carboxylic acids (LCAs). Hydroxyl radicals (HO•) can react with LCAs to generate the highly reducing carbon dioxide anion radical (CO2•−). Excited triplet state dissolved organic matter (3DOM*), a common oxidant in surface waters, may also oxidize LCAs to CO2•−, but this pathway remains unexplored. This study simulated sunlight-driven generation of CO2•− via 3DOM* using 4-benzoylbenzoic acid (CBBP) as a 3DOM* precursor and formate (HCOO−) as a model LCA. Metronidazole (MNZ) served as the target pollutant. Comparative degradation experiments in hν, hν/HCOO−, hν/CBBP, and hν/CBBP/HCOO− systems, combined with electron spin resonance spectroscopy and quenching tests, confirmed that CO2•− generated in the hν/CBBP/HCOO− system was the primary reactive species responsible for enhanced MNZ degradation, originating mainly from 3CBBP* oxidizing HCOO−. Under optimized conditions (8 mmol·L−1 HCOO−, 200 μmol·L−1 CBBP, 10 μmol·L−1 MNZ), 98.2% degradation was achieved within 30 min. Degradation efficiency increased with HCOO− concentration and was pH-independent. Cl−, NO3−, CO3^2−, and low concentrations of HCO3− inhibited degradation, while high HCO3− slightly promoted it. Humic acid (HA) inhibited degradation in a concentration-dependent manner. The system also performed well in real water matrices, suggesting potential for treating micropollutants via reductive pathways.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604019
A two-stage electrostatic precipitator (ESP) integrating a sawtooth-rod electrode precharging unit and a plate-plate collection unit was developed for simultaneous removal of fine particles and volatile organic compounds (VOCs) from catering fumes. Using KCl particles and toluene as surrogates, the system achieved a fine particle (<0.3 µm) collection efficiency of 91% and a total particle collection efficiency exceeding 98% at applied voltages of +12 kV (sawtooth-rod) and -8.5 kV (plate-plate), with an ozone concentration of 176.9 mg/m³. The presence of particles enhanced toluene degradation, increasing removal efficiency from 29.2% to 53.1%. Positive DC discharge on the sawtooth-rod electrode yielded a higher corona current (800 µA vs. 375 µA for negative) and lower ozone generation (101.4 mg/m³ vs. 176.9 mg/m³), indicating superior suitability for catering fume treatment. The stable discharge characteristics of the sawtooth-rod electrode reduce energy consumption and extend operational cycles, offering a promising technical pathway for efficient, compact, and intelligent ESP systems in catering fume purification.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225184
Thermal power units have long dominated China's energy structure due to the low cost of coal and their role in ensuring grid stability. However, under the dual pressures of climate change and national carbon peaking/neutrality goals, the environmental impact of their 'three wastes' has become critical, necessitating energy-saving retrofits. This review systematically examines mainstream energy-saving technologies for thermal power units, including boiler combustion optimization, heating surface cleaning, turbine flow path upgrades, waste heat recovery and cascade utilization, and cold-end system optimization. Using coal consumption rate as the core economic index, the study integrates case studies and operational data from typical domestic and international units to evaluate the latest progress, practical effects, advantages, and limitations of each technology. Results indicate that these technologies significantly improve energy efficiency and reduce pollution. For instance, boiler combustion optimization based on support vector machines and neural networks enhances thermal efficiency and reduces NOx emissions. Turbine flow path modifications, from full three-dimensional CFD optimization to advanced blades and combined steam seals, yield notable gains in cylinder efficiency and heat rate reduction. Low-temperature economizers reduce coal consumption and auxiliary power/water use in dust removal and desulfurization systems. Heat pump applications include absorption, compression, and hybrid types. In cold-end optimization, data-driven predictive maintenance and real-time performance tuning of condensers achieve nearly 50% energy savings in circulating water pumps and an average coal consumption reduction of 2-3 g/(kW·h). Despite these advances, gaps remain in multi-objective optimization robustness, intelligent diagnosis, and advanced materials. Future research should focus on deep reinforcement learning for adaptive control, sensor networks for real-time diagnostics and predictive maintenance, and high-temperature corrosion-resistant materials for heat exchangers, while balancing initial investment and maintenance costs.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010201
The Guanzhong region, traversed by the Wei River Basin, is one of the most industrially, agriculturally, and medically advanced and densely populated areas in Northwest China, has seen increasing attention paid to the pollution of perfluoroalkyl substances (PFASs) in its surface water environment. This study systematically investigated the pollution characteristics of PFASs in the surface water of this region and their ecological and health risks. By optimizing the online solid-phase extraction-liquid chromatography-tandem quadrupole mass spectrometry (Online SPE-LC/MS/MS), efficient detection of 19 PFASs was achieved, with the method detection limits ranging from 0.2 ng·L−1 to 0.3 ng·L−1, linear correlation coefficients all ≥ 0.990, and spiked recoveries between 75.2% and 130.0%. Monitoring data indicated that PFBA, PFPeA, PFHxA and PFOS, short-chain perfluorinated compounds, were the main pollutants in this region, with high detection frequencies and concentrations, but the overall content was lower than that in most areas of China. The concentrations of PFASs in surface water showed significant seasonal variations, with the highest concentrations during the dry season (∑19PFASs:126.1 — 2584.3 ng·L−1), followed by the normal season (∑19PFASs:3.5—3567.6 ng·L−1), and the lowest during the wet season (∑19PFASs:26.3—294.6 ng·L−1). Ecological risk assessment showed that, except for PFDoDA in the dry season, the ecological risk quotient (RQ) of all other PFASs was < 1. Although the water of the Wei River is not used as direct drinking water, health risk assessment indicated that all PFASs posed low risks, with only PFOA and PFOS showing potential risks (HR > 0.1) to adults and children at some sites during dry/normal seasons. This study provides a scientific basis for PFASs pollution control in the Wei River Basin.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012101
Continuous monitoring of 114 volatile organic compounds (VOCs) was conducted in the urban atmosphere of Haigang District, Qinhuangdao City, from September 2022 to February 2023. The volume concentrations of total VOCs were 42.72×10⁻⁹ in autumn and 25.15×10⁻⁹ in winter. The predominant species were isopentane, ethane, and ethylene. Ozone formation potential (OFP) analysis indicated that alkanes and alkenes dominated the atmospheric pollution during autumn and winter, with isopentane and ethylene being the largest contributors. Aromatic hydrocarbons contributed up to 85.00% of the secondary organic aerosol formation potential (SOAFP), with benzene as the primary species. Positive matrix factorization (PMF) identified four major sources: technological processes and oil/gas volatilization (35.57%), combustion and petrochemical emissions, motor vehicle emissions, and regional background sources. The results underscore the need for targeted control of VOCs from industrial and vehicular sources to mitigate secondary pollution in coastal cities.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605006
Military ecological and environmental protection is a critical component of national ecological and environmental protection. Military activities and operations, such as training and drills, weapons and equipment testing, and combat, are prone to triggering a series of ecological and environmental problems, including greenhouse gas emissions, deterioration of water resources and water quality, vegetation destruction, land degradation, and typical physical and chemical pollution, which have attracted extensive global attention. This study systematically analyzed the eco-environmental impacts of military activities on multiple environmental media (atmosphere, water, and soil) across different periods, and conducted pollution source tracing in multi-media and representative regions. It reviewed the current status of ecological and environmental protection technologies for the three major environmental media, i.e., atmosphere, water, and soil, and summarized the characteristics and constraints of military ecological and environmental research. Finally, it proposed the research trends and key development directions for military ecological and environmental protection from four dimensions: data monitoring and sharing, research and development of in-situ remediation technologies for military-civilian integrated combined pollution, green construction practices for military facilities, and optimization of management systems.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225250
Slag foaming is a critical phenomenon in electric arc furnace (EAF) steelmaking, enhancing thermal efficiency, suppressing metal splashing, and stabilizing the refining process. Accurate prediction and control of slag foaming are essential for green and efficient steelmaking. This review systematically examines research progress on slag foaming prediction, clarifying the applicability, advantages, and limitations of different predictive methods to support intelligent control of foamy slags. Following the framework of 'influencing factors-prediction methods-development trends', the study summarizes the coupling effects of multiple variables such as basicity, viscosity, surface tension, suspended particles, gas parameters, and temperature on foam formation and stability. It compares five major prediction approaches: empirical formulas, dimensionless modeling, thermodynamic calculations, computational fluid dynamics (CFD) simulations, and machine learning models, analyzing their core concepts, merits, and constraints. Results indicate that single models often struggle to balance real-time capability and accuracy, particularly under multi-variable coupling and complex operating conditions. Therefore, a hybrid prediction framework combining mechanism-based and data-driven models is proposed, emphasizing physical constraints, multi-scale coupling, and multi-source data fusion. This integrated approach is expected to advance slag foaming prediction from 'computable' to 'controllable and adjustable', offering methodological insights for the development of green and intelligent EAF steelmaking.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605024
The refined quantification of carbon footprint in engineering construction projects is critical for formulating targeted carbon reduction strategies during the materialization phase. This study integrates material flow analysis (MFA) with the emission factor method to establish a panoramic carbon flow model for engineering projects. Construction activities are categorized into processing and construction, and office and daily operations, clarifying material and carbon flow relationships within the system boundary and with external systems. Empirical analysis was conducted on the Hejiawan Bridge of Section 11 of the Xiyu High-Speed Railway. Results show that the total carbon flow amounts to 27,482,432.11 kg CO2eq, with direct carbon flow (fuel oil, gasoline) accounting for 7.6% and indirect carbon flow (products, transportation, electricity) accounting for 92.4%. From the material flow perspective, the total carbon flow comprises product carbon flow (72.88%), resource and energy carbon flow (25.73%), transportation carbon flow (1.04%), waste carbon flow (0.35%), and service carbon flow (0.01%). In terms of activity scope, construction-related carbon flow accounts for 99.17%, while office and daily operations account for 0.46%. Two indicators, material consumption carbon flow rate and energy consumption carbon flow rate, are proposed for the first time. Comparative analysis of five girder bridges reveals that the Hejiawan Bridge has a material consumption carbon flow rate of 3.91 kg CO2eq/kg, ranking highest among similar bridges, while its energy consumption carbon flow rate is 13.40 kg CO2eq/kg ec, at a medium level. The assessment indicates relatively high material consumption, suggesting potential for carbon reduction through structural and geological optimization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3798-x
Ulcerative colitis (UC) is a chronic inflammatory disorder of the colorectal mucosa, where conventional enema therapies suffer from poor retention and limited inflammation modulation. Here, we report a highly fluid probiotic-containing enema solution (s-BSA-Fe+EcN) integrating bovine serum albumin (BSA), Fe2+, and probiotic Escherichia coli Nissle 1917 (EcN). The solution's high fluidity enables comprehensive coverage of irregular colorectal mucosa. Upon encountering reactive oxygen species (ROS)-rich inflamed lesions, Fe2+ mediates H2O2 scavenging and hydroxyl radical generation, triggering BSA crosslinking and in situ gelation into a conformal hydrogel (h-BSA-Fe+EcN). This targeted adhesion mitigates oxidative damage to host tissues and preserves probiotic viability. In a porcine model, endoscopic imaging confirmed inflammation-targeted gelation in vivo. In a dextran sulfate sodium-induced mouse colitis model, h-BSA-Fe+EcN demonstrated excellent therapeutic efficacy, reducing disease activity index and restoring colonic architecture. This strategy addresses the dual challenges of fluid perfusion and rapid ROS-responsive gelation, offering an advanced transanal treatment for UC.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3750-6
SnSe is a promising thermoelectric material for medium-temperature applications due to its ultralow lattice thermal conductivity. However, the poor electrical conductivity of n-type polycrystalline SnSe significantly hinders its practical application. Here, we propose a dual-functional strategy employing InBr3 doping to synergistically enhance electrical transport while suppressing lattice thermal conductivity. For the first time, we demonstrate the successful construction of a Br-enriched conductive network within the SnSe matrix. The incorporation of In3+ and Br− introduces high-density charge carriers, while Br forms percolative conductive networks, resulting in a remarkable enhancement of carrier mobility to ~20.64 cm2 V−1 s−1. Simultaneously, the lattice thermal conductivity is substantially reduced to ~0.25 W m−1 K−1 through the formation of multi-scale defects, including dislocations and Br-rich nanowires, which effectively enhance phonon scattering. As a result, we achieve a peak figure of merit of ZT ~1.41 at 823 K, with an average figure of merit of ~0.42 over the temperature range of 323–823 K. This work provides a universal paradigm for decoupling electron-phonon interactions in thermoelectric materials, offering new insights for the optimization of thermoelectric performance.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509067
Marine litter poses a significant threat to coastal ecosystems globally, necessitating a comprehensive understanding of its multi-compartment distribution and driving mechanisms for effective management. This study investigated the occurrence, composition, and sources of beach, sea surface, and seafloor litter in the northeastern Daya Bay, a semi-enclosed bay, during August–October 2024. Sampling included 11 beach transects, 6 surface transects, and 25 seafloor transects. Results showed that the mean density of large and very large beach litter was 4.41×10^5 items·km−2, while medium beach litter reached 5.39×10^6 items·km−2. Surface litter densities were 5.82×10^2 and 9.90×10^3 items·km−2 for large/very large and medium fractions, respectively. Seafloor litter averaged 5.20×10^3 items·km−2. Plastics dominated all compartments, accounting for 74.0% (beach), 96.0% (surface), and 78.8% (seafloor) of total litter. Source apportionment using NOWPAP methodology indicated that beach and surface litter primarily originated from coastal recreational activities, whereas seafloor litter was mainly derived from shipping and fishing. Beach quality assessment revealed that 63.6% of beaches were moderately clean or better (grade II–IV), and 90.9% were moderately safe or better (grade I–III). Hotspots included tourism beaches, tidal gyre areas, coral reef zones, and fishing grounds. The study underscores the need for targeted management, including improved waste collection on tourist beaches, dynamic cleaning protocols, and port reception facilities for fishing waste.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510041
This study presents a full-scale engineering practice of retrofitting an idle upflow anaerobic sludge blanket (UASB) reactor into an aerobic granular sludge (AGS) system for treating low-strength municipal wastewater. The design capacity was 20,000 m3/d (maximum 24,000 m3/d), achieving separate treatment of industrial and domestic wastewater to reduce operational costs. Systematic analysis covered hydraulic capacity enhancement, effluent quality, pollutant removal efficiencies, sludge granulation progress, and operational costs. Results showed rapid start-up: the system reached 75% of design capacity by day 10 and 90% by day 26. During a 4-month operation, average removal efficiencies for COD, NH4+-N, TN, and SS were 83.2%, 97.0%, 75.9%, and 94.4%, respectively, even under low influent BOD5/TN ratios (typically below 4). Granulation progressed quickly: by day 44, average particle size was 2.6 times that of the inoculum and over 4 times that of flocs, with granules (>200 μm) accounting for 17.3%; by day 110, these values increased to 3.2 times and 5 times, with granule proportion reaching 33.4%. Compared to the previous year (June–August), the AGS process reduced electricity consumption, chemical consumption, and sludge production by 77.3%, 25.4%, and 30.4%, respectively, while saving 65.6% of footprint. This ten-thousand-ton case provides a practical basis for AGS technology application in China.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025030501
Coastal areas serve as critical ecological interfaces for the migration of terrestrial microplastics (MPs) into the ocean, and characterizing their pollution is essential for integrated coastal management. This study investigated the occurrence, sources, and ecological risks of MPs in surface waters of nearshore areas and river estuaries around Hainan Island, a typical tropical tourist island. MPs abundance ranged from 316.67 to 1300 n·m−3 in seawater and from 400 to 5416.67 n·m−3 in river water. In seawater, the dominant polymer was polyethylene terephthalate, with fibers being the predominant shape, size class 500–1000 μm, and white/transparent color. In river water, polypropylene-ethylene copolymer dominated, also as fibers, but with size class 100–500 μm and white/transparent color. Seawater MP abundance showed a significant positive correlation with tourist numbers, and distribution across functional areas followed: tourism areas > natural areas > aquaculture areas > residential areas. Multiple correspondence analysis identified household plastic waste, laundry wastewater, aquaculture, and fishery products as primary sources of seawater MPs. Principal component analysis indicated homologous characteristics between seawater and river MPs, suggesting rivers are a major pathway for terrestrial MP transport to coastal zones. Ecological risk assessment revealed low pollution loads, with potential ecological risks moderate for seawater and medium-low for river water. Notably, 15% of seawater sampling sites exhibited polymer risk level Ⅳ, primarily driven by polyacrylonitrile's high biological toxicity. These findings provide a scientific basis for developing MP pollution control strategies in Hainan Island.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025022704
Secondary inorganic aerosols (SNA), comprising sulfate, nitrate, and ammonium, are critical contributors to PM2.5 pollution in the Fenwei Plain, yet their formation mechanisms remain poorly characterized. Wintertime observations in Taiyuan revealed SNA as the dominant PM2.5 component, with a mean mass concentration of 33.19 ± 18.72 μg m−3, accounting for 47.13% of total PM2.5 mass. SNA concentrations increased markedly with pollution severity, but even under relatively clean conditions, SNA maintained a high mass fraction. Diurnal variation and correlation analyses indicated that nitrate formation pathways differed between day and night, largely governed by relative humidity (RH). During daytime, high RH (>55%) facilitated the partitioning of gaseous HNO3 to particulate nitrate. At night, RH positively correlated with nitrate concentration and nitrogen oxidation rate (NOR), with increased aerosol liquid water content (AWC) promoting NO2-to-nitrate conversion. The PM2.5 pH ranged from 4.3 to 5.2, and sulfate formation was primarily driven by H2O2 oxidation, with NO2 oxidation as a secondary pathway. These findings enhance understanding of SNA formation in the Fenwei Plain and provide a scientific basis for air quality policy.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606001
Municipal sludge anaerobic resource recovery efficiency in China lags behind developed countries. Widespread chemical phosphorus removal increases iron and aluminum salt precipitates in waste activated sludge, forming chemical-biological sludge that reduces acidogenic efficiency. This study identified key factors and developed a high-precision prediction model. Integrating literature and experimental data, acidogenic performance indicators under various conditions were compiled. Five machine learning models—Backpropagation Neural Network, Adaptive Neuro-Fuzzy Inference System, Support Vector Machine, K-Nearest Neighbors, and Random Forest—were systematically compared. Random Forest achieved the best predictive performance with a test set coefficient of determination (R²) of 0.9463, significantly outperforming others with minimal overfitting risk, demonstrating strong capability for high-dimensional, nonlinear, multi-factor coupled problems. Feature importance analysis revealed pH and Volatile Suspended Solids (VSS) as primary drivers, with aluminum salts exerting greater influence than iron salts. Engineering optimization should follow the pathway: 'adjust pH, stabilize organic matter, control aluminum salts'. This study provides an intelligent predictive tool and clarifies optimization directions, advancing precision and intelligent sludge treatment.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606006
Chitosan-based microsphere composites have attracted considerable attention for phosphorus adsorption due to their facile preparation, low cost, environmental friendliness, and high uptake capacity. This review summarizes the physicochemical properties and preparation methods of chitosan microspheres for phosphate removal, outlines common modification strategies to enhance adsorption capacity, and discusses their applications in aqueous environments. Adsorption mechanisms, regeneration, and resource recovery of spent microspheres are analyzed. Challenges and recommendations are proposed, including streamlined preparation, enhanced phosphorus recovery, removal of multiple phosphorus forms, and practical implementation. The review aims to guide the development of high-performance chitosan-based microspheres for phosphorus removal.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3790-5
Near-infrared (NIR) phosphors with high quantum efficiency (QE) and thermal robustness are critical for phosphor-converted light-emitting diodes (pc-LEDs). Here, a Cr3+-activated Lu2BaAl4SiO12 (LBASO) garnet phosphor is engineered via chemical unit cosubstitution of [Ba2+-Si4+] for [Lu3+-Al3+] in Lu3Al5O12 (LuAG), inducing a strong crystal field that yields NIR emission at 705 nm. The optimized LBASO:0.07Cr3+ exhibits an internal quantum efficiency (IQE) of 84.82% and external quantum efficiency (EQE) of 46.02%. Notably, it demonstrates anti-thermal quenching (ATQ) with 126.03% of its initial intensity at 498 K under 442 nm excitation, attributed to a wide band gap, weak electron-phonon coupling, defect trap energy levels, high structural rigidity, and optimized electron population distribution. A NIR pc-LED fabricated with this phosphor achieves an output power of 134.99 mW and photoelectric conversion efficiency of 11.4% at 100 mA drive current. These results underscore the potential of LBASO:Cr3+ for applications in plant lighting, night vision, and nondestructive analysis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3894-9
Photocatalytic production of hydrogen peroxide (H2O2) using water and O2 offers an economical, environmentally friendly, and sustainable route for H2O2 synthesis. However, current photocatalytic systems suffer from poor charge carrier transport, narrow light absorption, and insufficient active sites, leading to unsatisfactory H2O2 production efficiency. In this study, a CoS/ZnIn2S4 (ZIS) composite was constructed by in-situ growing CoS nanoclusters on ZIS via a solvothermal method for photocatalytic H2O2 production. The integration of CoS with ZIS broadened the light absorption spectrum. The optimized CoS/ZIS-3 composite exhibited an exceptional H2O2 production rate of 2693.39 μmol g−1 h−1 under visible light in isopropanol, surpassing pristine ZIS and CoS by factors of 6.54 and 18.08, respectively. The S-scheme heterojunction and built-in electric field synergistically enhanced the separation and transportation of photogenerated charge carriers, thereby improving photocatalytic efficiency. The H2O2 synthesis mechanism involves dual-channel oxygen reduction and water oxidation reactions mediated by CoS/ZIS. The produced H2O2 effectively degraded organic pollutants and inhibited the growth of E. coli. This study presents a promising green strategy for enhancing ZIS-based photocatalysts through constructing S-scheme heterojunctions for efficient H2O2 synthesis.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202505108
Open-pit mining in high-cold regions causes severe ecological degradation, including vegetation loss, soil structure destruction, and frequent freeze-thaw disturbances, complicating ecosystem recovery. This review systematically synthesizes the current status, theories, and key restoration technologies for degraded ecosystems in high-cold mining areas. Comparative analysis with typical high-cold degraded ecosystems worldwide reveals that high-cold mining areas face challenges such as frequent freeze-thaw cycles, hydrological disruption, wind erosion, and difficult vegetation establishment. We propose strengthening aboveground-belowground synergistic restoration: (1) aboveground restoration should focus on screening cold-resistant native plants and optimizing mixed community configurations, combined with plant growth-promoting multi-microbial consortia to facilitate vegetation recovery; (2) belowground restoration should be based on engineering soil profile reconstruction, integrating physical-chemical-biological multi-dimensional remediation techniques to achieve aboveground and belowground community reconstruction and functional recovery; (3) a progressive restoration framework is established, with short-term goals targeting soil stabilization and structure improvement, medium-term goals focusing on constructing multifunctional plant-soil communities, and long-term goals achieving self-sustaining, maintenance-free restored ecosystems. Finally, addressing the unclear mechanisms of aboveground-belowground synergistic interactions and insufficient environmental adaptability of restoration technologies, two prospects are proposed: (1) deepening research on aboveground-belowground synergistic mechanisms to reveal interactions between cold-tolerant microorganisms and plants; (2) advancing the development of characteristic restoration technologies adapted to high-cold environments.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607012
This study investigated the effects of lychee wood biochar and lignin-degrading bacteria on compost maturity, substance transformation, and bacterial communities during the coupled process of aerobic composting and vermicomposting of cow dung and rice husk. Four treatments were established: no addition (CK), 5% (w/w) lychee wood biochar addition (T1), 0.5% (w/w) lignin-degrading bacteria (Bacillus subtilis, Aspergillus niger) addition (T2), and combined addition of 5% biochar and 0.5% bacteria (T3). Results showed that biochar and/or bacteria addition accelerated temperature rise, extended high-temperature duration to 13 days, and increased maximum temperature. Compared to CK, T1–T3 increased organic matter degradation by 3.97%–9.56%, humic acid content by 12.30%–24.09%, available phosphorus and potassium by 14.48%–32.50% and 6.97%–18.85%, respectively. NH3 emissions were reduced by 25.86%–34.26%, while nitrate nitrogen and total nitrogen increased by 12.83%–43.34% and 5.73%–13.18%, respectively. Seed germination index improved by 11.62%–29.20%. T3 exhibited the best overall performance. During aerobic composting, biochar and/or bacteria significantly increased relative abundances of Bacteroidota, Planctomycetota, and Acidobacteriota, but effects were not significant during vermicomposting. Functional genera such as Bacillus, Pseudomonas, and Chryseolinea were enriched in both stages. The study concludes that adding 5% lychee wood biochar and/or 0.5% lignin-degrading bacteria to cow dung and rice husk in coupled composting-vermicomposting improves bacterial community structure, promotes organic matter degradation, enhances humification, reduces nitrogen loss, and accelerates compost maturity, with combined addition being most effective.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3975-2
The instability of oxygen redox activity in layered oxide cathodes, particularly the formation of localized electron holes on oxygen (O−) and subsequent anion dimerization, has been demonstrated to trigger rapid capacity degradation and severe voltage hysteresis. Our study primarily focuses on P3-type Na2/3Cu1/3Mn2/3O2, which demonstrates reversible oxygen redox with an exceptionally low voltage hysteresis of 0.05 V. Spectroscopic analyses demonstrate a reversible O2−→O− evolution in Na2/3Cu1/3Mn2/3O2 without O–O dimerization. Furthermore, Multilateral non-invasive magnetic methods reveal that strong Cu-O-Mn superexchange interactions during the metal-ligand redox process lead to delocalization of O− species and inhibition of irreversible O–O bonding, thereby enabling ultralow voltage hysteresis. This work establishes magnetic exchange engineering as a transformative strategy to unlock reversible oxygen redox in high-energy battery electrodes.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511027
Aquaponics systems integrate aquaculture and hydroponics to recycle resources, yet nutrient recovery from aquaculture sludge remains inefficient. This study investigated anaerobic acidification as an alternative to conventional anaerobic digestion, which suffers from long conversion cycles. Batch experiments compared two sludge loading rates: high (13.22 kg·kg−1) and low (4.61 kg·kg−1) (mass of sludge per mass of anaerobic inoculum). Under low loading, soluble chemical oxygen demand (SCOD) exhibited a single peak, reaching a maximum organic solid conversion of 68.2% at 70.5 h. In contrast, high loading produced three SCOD peaks with an average peak conversion efficiency of only 26.9% at 27.5 h and higher residual concentrations. Ammonia nitrogen conversion was slightly higher under low loading (64.8%) than high loading (62.2%), while orthophosphate conversion was markedly superior (95.7% vs. 76.4%). The optimal hydraulic retention time for low-loading operation was 144 h, corresponding to an organic loading rate of 0.77 kg·(kg·d)−1. Under these conditions, the produced ammonia and phosphate can be effectively recovered without adversely affecting water quality, as the biofilter converts ammonia to nitrate for plant uptake. Microbial analysis revealed that low-loading conditions favored the dominance of Acinetobacter (relative abundance 66.6%), which likely enhances organic degradation and nutrient release. These findings demonstrate that anaerobic acidification under low loading is a promising strategy for efficient nutrient recovery in aquaponics, offering a shorter conversion time and higher nutrient yields than traditional methods.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512014
Mining activities cause severe soil degradation and microbial diversity loss, impeding ecological restoration. This study evaluated the effects of a novel soil amendment, microporous bio-gravel (MBG), on bacterial and fungal community structure and function in degraded soil from the Baiyinhua open-pit mine, Inner Mongolia. A pot experiment with four MBG-to-soil volume ratios (CK, L=1:3, M=1:2, H=1:1) was conducted, with a simplified plant community and uniform fertilization. After 180 days, soil samples were analyzed via high-throughput sequencing and bioinformatics. Results showed that the medium ratio (M) significantly increased fungal Shannon index and evenness, while the high ratio (H) negatively affected bacterial communities. At phylum and genus levels, MBG promoted enrichment of Cyanobacteria and specific functional groups (e.g., nitrogen-fixing bacteria, Bacillus). Co-occurrence network analysis revealed peak complexity, modularity, and average degree in bacterial and fungal networks under the M treatment. Functional prediction indicated significant enrichment of pathways related to lipopolysaccharide biosynthesis, nitrotoluene degradation, and plant-pathogen interactions, alongside increased abundance of saprotrophic and ectomycorrhizal fungi. Mantel and VPA analyses showed that MBG indirectly regulated microbial community structure by improving soil physicochemical properties and plant traits, with stronger effects on fungi than bacteria. In conclusion, MBG optimizes the soil microhabitat and plant-soil-microbe interactions, modulating microbial diversity, network complexity, and functional potential. The medium ratio (1:2) was most effective, demonstrating potential for ecological restoration of degraded mine soils.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60656-1
Under the carbon neutrality strategy, biomass boilers have emerged as key facilities for renewable energy utilization, yet are characterized by low-concentration SO2 emissions. Ca-based dry desulfurization presents a promising technology for biomass boiler flue gas purification due to its compact structure, low capital investment and simple operation and maintenance. However, it is generally limited by the low adsorbent utilization and insufficient desulfurization efficiency. Herein, this study developed a novel Ca-Mn composite adsorbent through a synergistic strategy integrating F127 surfactant to optimize dispersion and Mn loading to enhance oxidation efficiency. The resulting adsorbent not only significantly increased the breakthrough sulfur capacity of the Ca-based material but also markedly improved the synergistic removal of Hg0. It was demonstrated that the introduction of Mn elements and F127 effectively suppressed the agglomeration of Ca(OH)2 crystallites and induced an oxygen vacancy-rich structure, while simultaneously optimizing the pore structure of the adsorbent. The modified adsorbent exhibited the enlarged specific surface area and pore volume, which favored to enhance the reaction mass transfer and effectively prevent the pore blockage and coverage of active sites by desulfurization products. The Mn sites and oxygen vacancies formed catalytic centers, which not only accelerated the desulfurization reaction by promoting SO2 oxidation but also enabled the adsorbent to couple with Hg0 catalytic oxidation functionality. Consequently, the simultaneous removal of SO2 and Hg0 was significantly enhanced on the Ca-Mn composite adsorbent.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042304
To characterize the spatial variability of PM2.5 chemical components at the urban scale, ambient PM2.5 samples were collected from eight sites across Changsha, China. Samples were analyzed using ion chromatography, elemental carbon/organic carbon (EC/OC) analysis, and X-ray fluorescence (XRF) spectroscopy. Results showed that PM2.5 concentrations in urban areas were significantly higher than in suburban locations, with notably elevated levels at Changsha New Railway Station and Mapoling. Across different PM2.5 pollution levels, the eight sites exhibited pronounced spatial differences in concentration while sharing similar chemical compositions. Source apportionment identified secondary nitrate, vehicle emissions, and secondary sulfate as major contributors to PM2.5. The spatial distribution of these sources varied distinctly: secondary nitrate showed lower contributions in central areas but higher in western and southeastern regions; secondary sulfate was more prominent in the southeast, while vehicle emissions contributed more in the southeast and less in the west. Additionally, aerosol liquid water content promoted the secondary formation of nitrate and sulfate, exacerbating PM2.5 pollution. Secondary organic carbon was elevated in areas with high pedestrian density, suggesting enhanced secondary organic aerosol formation under intensive human activity. The study provides insights for targeted pollution control strategies in Changsha and similar cities.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025111403
Sediments from the Hengyang reach of the Xiangjiang River were analyzed for concentrations, chemical fractions, and sources of 14 heavy metals (As, Se, Cd, Sb, Pb, Tl, Bi, Co, Ni, Mn, Zn, V, Cr, Cu). Mean concentrations of As, Se, Cd, Sb, Pb, Tl, and Bi exceeded local background values, with Cd, Se, Bi, and As showing pronounced enrichment. Spatial heterogeneity was marked, with higher levels downstream; overall concentrations were lower than previously reported. Sequential extraction revealed that Sb, Bi, Se, Tl, Cu, As, V, Cr, and Ni were predominantly in the residual fraction (F4), while Zn, Cd, Pb, and Mn had higher extractable fractions (F1+F2+F3), with bioavailable fractions generally elevated downstream. Geo-accumulation index (Igeo) indicated no contamination by Co, Zn, V, or Cr, but varying degrees of contamination by Mn, Ni, As, Se, Cd, Sb, Pb, Tl, Bi, and Cu, with pollution severity order: Se>Cd>Bi>As>Sb>Pb>Tl>Ni>Cu>Mn>Zn>Cr>Co>V. Enrichment factors showed significant enrichment for Cd, Sb, and Bi, moderate for Pb, and low for others. Potential ecological risk index (RI) revealed Cd as the primary contributor (87.49% of total risk), with overall moderate risk at downstream sites and slight risk across the entire section. Source apportionment using PCA and PMF identified three sources: industrial and traffic mixed source (57.60%), natural source (16.00%), and industrial-natural mixed source (26.40%). These findings enhance understanding of heavy metal pollution mechanisms in the Hengyang section and recommend priority control of industrial and traffic emissions, with focus on Cd mobility, to support sediment remediation strategies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4021-5
Lead-free halide double perovskites have attracted significant attention owing to their eco-friendliness, structural tunability, and self-trapped exciton emission. Nevertheless, achieving efficient and stable near-infrared-II (NIR-II) luminescence, especially in materials incorporating lanthanide ions, remains a considerable challenge in photonics research. Herein, we report a notable advance in the design and synthesis of Sb3+-sensitized Cs2NaLuCl6:Er3+ double perovskite single crystals, which exhibit an unprecedented external quantum efficiency of 45.3% for emission at 1542 nm. Sb3+ acts as a broadband ultraviolet absorber and transfers energy to Er3+ via self-trapped exciton emission. Moreover, at high concentrations of Er3+, Er3+-Er3+ cross relaxation (2H11/2 + 4I15/2 → 4I9/2 + 4I13/2) selectively populates the NIR-emitting 4I13/2 state, suppressing competitive visible emission pathways. This synergistic host-sensitizer-activator design strategy, supported by density functional theory calculations, addresses long-standing efficiency limitations and opens new avenues for high-performance NIR-II emitters in bioimaging, night vision, and optical communications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4070-2
A series of ~20 nm intermetallic Pd3Pb nanocubes with tunable surface Pb exposure were synthesized via a facile one-step solvothermal approach, providing an ideal system to investigate the way in which the surface configurations of Pb-rich (Pd3Pb/Pb), Pd-rich (Pd3Pb/Pd), and standard Pd3Pb nanocubes influence the CO2 reduction reaction (CO2RR) mainly through the ligand effect while excluding geometric influences. Electrochemical measurement results indicate that the Pd3Pb/Pb catalyst delivered outstanding C1+ selectivity, achieving a high Faradaic efficiency of 96.88% at −0.72 V (vs. RHE), significantly outperforming the Pd3Pb/Pd (39.86%) and standard Pd3Pb (81.75%) counterparts. In situ FTIR together with DFT calculations further elucidated that Pb incorporation can modulate the electronic structure of Pd via p-d hybridization, leading to the upshift of the d-band center. This will, in return, strengthen the intermediate adsorption ability and lower the energy barriers of the C1+ pathways while effectively suppressing the competing hydrogen evolution reaction. This work establishes a precise surface engineering paradigm of intermetallic nanocrystals for designing high-performance electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4123-0
Aqueous aluminum-ion batteries (AAIBs) are promising for large-scale energy storage due to safety, sustainability, and theoretical high capacity. However, sluggish electron/ion transport in conventional cathodes limits rate capability. Here, we first propose high-entropy engineering of metal oxides (HEOs) as cathodes in AAIBs, leveraging the 'cocktail effect' and abundant electron transport pathways to enhance rate-capacity. Atomic-level interactions between different metal atoms broaden the d-band with reduced electronic level degeneracy, facilitating rapid electron transport, achieving one of the best rate capabilities (119.4 mAh g−1 at 10.0 A g−1) among metal-oxide cathodes. The disordered layered oxides formed with a high-entropy framework alleviate electrostatic repulsion between aluminum ions and the fixed lattice, mitigating structural degradation and imparting excellent cycling stability (over 95.1 mAh g−1 after 500 cycles at 2.0 A g−1). The optimized HEO-Cr cathode (Fe0.6Co0.6Ni0.6Mn0.6Cr0.6O4) exhibits outstanding rate performance and cycling stability. DFT simulations and electrochemical tests reveal that multi-transition metal incorporation, bandgap narrowing, and unique lattice structure drastically enhance electron transport efficiency. The layered phase formed after cycling, based on a high-entropy framework, overcomes challenges from high charge density aluminum ions, significantly enhancing cycling stability. This work paves the way for high-performance AAIBs and other aqueous multivalent metal ion batteries by rationally designing high-entropy engineering.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4181-6
Green hydrogen production via electrocatalytic water splitting is pivotal for sustainable energy, yet the high cost and scarcity of platinum (Pt) catalysts impede large-scale adoption. Ruthenium (Ru)-based materials emerge as promising alternatives, but their performance requires enhancement. Two-dimensional transition metal dichalcogenides (TMDs), particularly ReS2, offer intrinsic 1T' phase with good conductivity and stability, yet suffer from inert surfaces limiting water adsorption. Here, we report a heterostructure comprising Ru nanoclusters anchored on ReS2 nanosheets (Ru/ReS2) to modulate electronic structure via d-p coupling. This design enhances water dissociation kinetics and optimizes hydrogen adsorption free energy (ΔG_H*). The Ru/ReS2 catalyst exhibits superior hydrogen evolution reaction (HER) activity in acidic media, achieving an overpotential of 47 mV at 10 mA cm−2 and a Tafel slope of 38 mV dec−1, outperforming commercial Pt/C (overpotential 54 mV, Tafel slope 45 mV dec−1). Notably, it demonstrates exceptional stability, with negligible degradation after 10,000 cyclic voltammetry cycles, contrasting with Pt/C's 54 mV overpotential increase. Density functional theory calculations reveal that d-p coupling between Ru and ReS2 optimizes the electronic structure, facilitating water adsorption and dissociation. This work provides a rational strategy for designing efficient, durable, and cost-effective HER electrocatalysts for green hydrogen production.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3631-1
Anion exchange membrane water electrolysis (AEMWE) offers cost and dynamic-response advantages over proton exchange membrane systems, yet commercial deployment is constrained by the alkaline stability of anion exchange membranes (AEMs) and the sluggish kinetics of non-precious metal catalysts. This work reports a series of poly(terphenyl-diphenylmethane piperidinium) (QPDPMTP) membranes synthesized with varied diphenylmethane (DPM) content. The alkyl chain of DPM induces pronounced microphase separation and elevates free volume fraction, yielding an OH− conductivity of 152 mS cm−1 at 80 °C for QPDPMTP-10. After 1032 h immersion in 6 M NaOH at 80 °C, the membrane retains 90.7% of its initial conductivity. An AEMWE cell integrating QPDPMTP-10 with a non-precious NiFeCo LDH/NiS/NF anode achieves 3.11 A cm−2 at 2 V in 1 M KOH at 80 °C and sustains 1 A cm−2 for 1800 h under gradient KOH concentration. These results establish a viable pathway for durable, low-cost AEMWE systems.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3542-8
Rechargeable sodium-chlorine (Na/Cl2) batteries derived from thionyl chloride (SOCl2) primary systems offer high theoretical energy density and wide-temperature operation, but their reversibility is constrained by chlorine shuttle and unstable sodium-metal interfaces. Dai et al. demonstrate a Na/Cl2 battery using multi-walled carbon nanotubes (MWCNTs) as the cathode host, a sodium-metal anode, and a SOCl2-based electrolyte containing AlCl3, potassium bis(fluorosulfonyl)imide (KFSI), and NaCl additives. The cell delivers an initial discharge capacity of 5400 mAh g−1 (carbon mass basis), a reversible capacity of 3500 mAh g−1, and a discharge plateau near 3.9 V at room temperature, sustaining over 140 cycles at rates up to 2 C with near 100% Coulombic efficiency. The dual-function KFSI additive suppresses sodium dendrites via electrostatic shielding from the lower K+/K redox potential and forms a NaF/KF-rich solid-electrolyte interphase. In situ Raman spectroscopy reveals reversible SCl2 and S2Cl2 formation at the end of charge, contributing an additional ~3.9 V plateau, while the main Cl−/Cl2 redox plateau remains at ~3.55 V. Cryogenic transmission electron microscopy shows NaCl nanocrystals deposited within the hollow cores of MWCNTs, and electron energy loss spectroscopy confirms uniform chlorine distribution on nanotube surfaces in the charged state. A high defect density (Raman D/G ratio = 1.01) and large pore volume (2.48 cm3 g−1) are identified as critical enablers of superior battery performance.