SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4245-4
The discrimination of volatile organic compounds (VOCs) at trace concentrations remains a critical challenge for environmental monitoring, industrial process control, and non-invasive disease diagnostics. Conventional electronic noses rely on sensor arrays comprising multiple chemically distinct receptors, which introduces fabrication complexity, calibration drift, and cross-sensitivity. Here, we demonstrate that a single-component Ti3C2Tx MXene (TM) sensor array, engineered through controlled surface chemistry and device architecture, generates independent and high-dimensional characteristics (IHC) sufficient for precise VOC pattern recognition. By exploiting the intrinsic heterogeneity of TM basal planes and edge sites, we achieve differential interaction motifs without expanding elemental composition. The array discriminates VOCs including acetone, ethanol, toluene, and hexane at concentrations down to 100 ppb with classification accuracy exceeding 95%. Principal component analysis reveals distinct clustering with cumulative variance of 92.3% captured by the first three principal components. The sensor exhibits a limit of detection of 50 ppb for acetone and response/recovery times of 12 s and 18 s, respectively. Long-term stability tests over 30 days show less than 5% signal degradation. This single-component strategy simplifies fabrication, reduces calibration overhead, and offers a scalable pathway for miniaturized, low-power VOC sensing platforms compatible with Internet of Things (IoT) deployment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4277-1
Two-dimensional (2D) magnetic materials hold promise for next-generation spintronics, yet most exhibit Curie temperatures (Tc) far below room temperature, limiting practical applications. Here, we report the realization of room-temperature ferromagnetism in CuCrSe2 nanosheets via controlled anion removal achieved by post-synthetic vacuum annealing. Raw CuCrSe2 shows a low Tc of ~120 K, whereas annealed CuCrSe2 (A-CuCrSe2) nanosheets exhibit robust ferromagnetic ordering above 300 K. Structural and compositional analyses, including transmission electron microscopy, Raman spectroscopy, and X-ray absorption spectroscopy, confirm that A-CuCrSe2 retains the original layered crystal structure with an estimated Se vacancy concentration of approximately 10%. Magnetic measurements reveal room-temperature ferromagnetism in exfoliated nanosheets, corroborated by magnetic imaging and electric transport measurements. Anomalous Hall effect (AHE) measurements uncover the coexistence of two ferromagnetic phases within the same sample: one with low Tc (~120 K) and another with high Tc (>300 K), indicating spatially heterogeneous magnetic ordering driven by anion removal distribution. Density functional theory (DFT) calculations elucidate the microscopic mechanism, suggesting that Se vacancies modulate the magnetic exchange interactions, enhancing Tc. This work demonstrates that anion modulation is an effective intrinsic strategy to achieve room-temperature ferromagnetism in 2D materials, potentially advancing spintronic applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4179-x
Perylene diimide (PDI) radical anions exhibit poor environmental stability, restricting their generation efficiency and practical application. Here, a PDI-functionalized bispillar[5]arene (PDI-P5) was designed to construct stable and high-efficiency photothermal radicals. Intramolecular charge transfer (ICT) between PDI and bispillar[5]arene narrows the energy gap. Under 455 nm ultraviolet light irradiation and diethylamine (DEA) vapor exposure, photoinduced electron transfer (PET) efficiently generates PDI-P5·− radicals, which possess broad near-infrared (NIR) absorption, enhanced non-radiative transitions, and excellent stability. Notably, PDI-P5·− can rapidly reach 90 °C under 0.20 W cm−2 simulated sunlight irradiation. Moreover, it exhibits superior multi-step photothermal anti-counterfeiting performance. This work provides a novel strategy for the development of stable radical-based photothermal materials, which holds great potential for anti-counterfeiting and bioimaging applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3536-5
Nanomaterial-based optical biomedicine and devices have attracted significant attention for tumor diagnosis and treatment, yet their application in tumor ablation is often hindered by limited functional integration and concerns over excessive radiation exposure. In this study, we address these challenges by developing a multifunctional fiber probe based on lanthanide-doped nanoparticles, featuring decoupled modules for localized heating and optical thermometry. This design enables synergistic therapy under near-infrared (NIR) laser irradiation. Beyond achieving precise photothermal ablation and real-time temperature monitoring, we uncovered a unique phenomenon: the generation of reactive oxygen species (ROS) by these nanoparticles under NIR laser excitation, even in the absence of traditional photosensitizers. Through a combination of experimental and computational approaches, we elucidated the physical mechanisms underlying ROS generation in wide-bandgap lanthanide nanoparticles. Leveraging these insights, we constructed an all-optical fiber system capable of simultaneous precise thermal control and photodynamic therapy. Our findings offer valuable guidance for the development of advanced optical nanomaterials and devices for effective tumor treatment, both in vivo and in vitro.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3676-3
Perovskite solar cells (PerSCs) have achieved remarkable efficiencies, yet their performance is limited by defect states and non-radiative recombination. Here, pyromellitic diimide (PD) is introduced as an additive to passivate bulk defects in perovskite films. PD forms hydrogen bonds with formamidinium (FA+) ions and coordinates with Pb2+ ions, effectively suppressing non-radiative recombination and reducing energy loss. The PD-treated perovskite films exhibit enhanced crystallinity and uniformity. Consequently, 1.55 eV PerSCs achieve a high open-circuit voltage (VOC) of 1.193 V and a power conversion efficiency (PCE) of 25.79%. Moreover, unencapsulated PD-treated devices retain 96% of their initial efficiency after 2000 h under nitrogen atmosphere, whereas control devices retain only 74%. Under ISOS-D-2I accelerated aging (65±5°C in N2), PD-treated devices show less than 5% PCE attenuation after 288 h, compared to ~30% for controls. This work provides a viable strategy for defect passivation in perovskite solar cells, enhancing both efficiency and stability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3705-5
Biodegradable metals (BMs) are designed to corrode gradually in physiological environments, yet this corrosion can compromise their mechanical integrity, potentially causing premature implant failure. For emerging zinc-based alloys, the corrosion-mechanical property relationship remains inadequately characterized. This study systematically investigated the long-term corrosion-associated mechanical behavior of hot-extruded Zn-Cu and Zn-Cu-Fe alloys, promising Zn-based bio-metals, in comparison with pure Zn, under immersion degradation in Hank's solution. Electrochemical impedance spectroscopy and mechanical testing revealed that the evolving corrosion profile governs mechanical performance. Alloying with Cu and Fe mitigated corrosion's detrimental effects: grain refinement reduced localized corrosion susceptibility, while finely dispersed second phases acted as cathodic sites, promoting uniform corrosion. Additionally, Cu and Fe facilitated the formation of protective corrosion product layers, suppressing further matrix attack. Consequently, the overall reduced corrosion, particularly localized corrosion, lowered stress concentration susceptibility, delaying mechanical decline and preserving structural integrity. These findings elucidate the degradation-mechanical property correlation in Zn-based bio-metals and underscore critical considerations for developing new bio-metals for clinical translation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3770-9
Intramolecular through-space charge-transfer (TSCT)-enabled thermally activated delayed fluorescence (TADF) emitters have shown exceptional potential for advancing organic light-emitting diode (OLED) technologies, owing to their efficient utilization of triplet excitons and optimized photophysical properties. To date, the intrinsic correlation among molecular geometries, intramolecular non-covalent interactions, and photophysical properties in TSCT-TADF emitters remains unconfirmed, and this study theoretically clarifies this critical correlation. Specifically, through integrating molecular engineering, screening strategies, first-principles calculations, energy decomposition analysis, and statistical modeling, we systematically investigated 24 experimentally reported TADF molecules, and 54 newly designed structures in both solution and thin-film environments. We establish a clear geometric criterion for high-efficiency TSCT-TADF emitters: donor-acceptor (D-A) dihedral angles below 25° and interfragment distances within 4 Å—conditions validated by both theoretical predictions and experimental evidence. Based on this insight, we designed two novel molecular libraries with benzene- or carbazole-derivative bridges, using O-bridged triphenylamine (DPXZ) as the donor and quinolino[3,2,1-de]acridine-5,9-dione (QAO) as the acceptor. Our calculations confirm that sub-25° D-A dihedral angles correlate with exceptional delayed fluorescence efficiency, with predictions reaching up to 96% and an average of 70% for the new thin film systems. This study provides a rational design strategy for high-performance TSCT-TADF emitters, significantly advancing the molecular-level understanding of through-space interactions and accelerating the discovery of tailored, efficient OLED materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3919-0
Nuclear energy is critical for sustainable economic development and achieving carbon neutrality. With only about 6.14 million tons of terrestrial uranium, sufficient for ~70 years of global nuclear power plant operation, the recovery of uranium from seawater and spent fuel is essential for long-term nuclear fuel supply. The ocean contains approximately 4.5 billion tons of uranium, which could sustain nuclear power for ~2000 years if efficiently extracted. However, seawater uranium extraction faces significant challenges due to the extremely low uranium concentration (~3.3 ppb), high concentrations of competing ions, natural organic matter, and marine biofouling. This perspective reviews representative laboratory advances, including sulfonated covalent organic frameworks (S-COF) achieving a sorption capacity of 31.5 mg/(g·day) with high selectivity, amidoxime-based organic cages with a capacity of 11.97 mg/g over 30 days, and a micro-redox reactor strategy that continuously regenerates binding sites. Electrochemical methods have also shown promise for converting soluble U(VI) to insoluble U(IV) oxides. Despite these advances, the transition from laboratory powders to durable marine materials remains problematic. Key gaps include the need for antibacterial properties, mechanical stability under wave action, cost competitiveness with terrestrial mining, and environmental safety of nanomaterials. Artificial intelligence (AI) is proposed to accelerate the design of high-performance, stable materials. This perspective emphasizes the necessity for interdisciplinary research to bridge the gap between bench-scale innovations and practical ocean deployment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3748-9
Direct regeneration is a sustainable solution for recycling spent lithium-ion batteries (LIBs), yet the irregular strains induced by the irreversible FePO4 phase after cycling hinder Li+ replenishment in spent LiFePO4 cathodes. This study proposes a lattice stress modulation strategy that reduces FePO4 to Fe2P2O7, reducing unit cell volume from 271.7 to 122.6 Å3, releasing residual stress and reconstructing continuous Li+ transport channels. The phase transformation reconstructs FeO6 octahedra, lowering the migration energy barrier for ions. This synergistically weakens steric effects, facilitating Li+ replenishment and eliminating Li-Fe anti-site defects. Regenerated LiFePO4 cathodes achieve 80.2% capacity retention after 1000 cycles at 2C, outperforming commercial cathodes. The work establishes fundamental principles for the pre-treatment stage of direct regeneration and provides a paradigm-shifting solution for sustainable LIB recycling.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3785-5
The effective separation and utilization of photo-generated carriers are critical for advancing photocatalysis, particularly in coupled reactions of H2 production and value-added chemical synthesis. Here, a sandwich-structured MnO2@ZnIn2S4@Ti3C2 hollow sphere was designed, with MnO2 and Ti3C2 loaded on the inner and outer surfaces of ZnIn2S4, respectively. MnO2 acts as an oxidation cocatalyst collecting photo-generated holes, while Ti3C2 serves as a reduction cocatalyst for electrons, promoting spatial separation of carriers and enabling spatially separated redox reactions. The hollow structure enhances light harvesting. The optimal catalyst achieves photocatalytic H2 production rate of 6.29 mmol g−1 h−1 and benzaldehyde production rate of 5.26 mmol g−1 h−1 from benzyl alcohol oxidation, significantly outperforming ZnIn2S4, MnO2@ZnIn2S4, and ZnIn2S4@Ti3C2. In situ irradiated X-ray photoelectron spectroscopy confirms effective carrier separation. In situ electron paramagnetic resonance and diffuse reflectance infrared Fourier transform spectroscopy reveal reaction intermediates. This work provides a strategy for designing efficient photocatalysts for coupled H2 production and selective oxidation.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604006
High-strength sulfamethoxazole (SMX) wastewater severely inhibits anaerobic microorganisms, reducing organic degradation and methane yield. This study investigated the effects of short-chain (C6-HSL) and long-chain (C12-HSL) N-acyl-homoserine lactone (AHL) signaling molecules, individually and in combination, on the construction, performance, and antibiotic resistance gene (ARG) profiles of anaerobic electroactive biofilms within a microbial electrolysis cell coupled anaerobic digestion (MEC-AD) system. Compared to the control (no AHLs), SMX removal efficiency increased by 9.26%, 7.44%, and 10.67% for C6-HSL (T1), C12-HSL (T2), and combined (T3) treatments, respectively. Methane production rates rose by 20.4%, 16.9%, and 23.1% for T1, T2, and T3, respectively. AHLs promoted extracellular polymeric substance secretion, enhancing electroactive microbe attachment to the anode. Microbial community analysis revealed increased diversity and modulated key functional genera. Notably, Georgenia abundance increased by 16.77% (T1) and 36.47% (T3) but decreased by 15.99% (T2). ARG analysis showed that single AHLs elevated intI1, sul1, and sul2 abundances, whereas combined AHLs (T3) exhibited a milder response, with sul2 abundance reduced by 4.92% relative to control. This suggests synergistic AHLs suppress ARG host proliferation. This study first demonstrates that combined short- and long-chain AHLs enhance electroactive biofilm formation, maintain microbial community stability, and modulate ARG dissemination risk, offering a quorum sensing-based strategy for antibiotic wastewater treatment and risk management.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3781-8
The 2xxx (Al-Cu-Mg) alloy is widely used in transportation fields due to its excellent strength-to-weight ratio. However, conventional heat treatments such as peak aging (PA) often result in a pronounced strength-ductility trade-off and limited fatigue resistance. To address these limitations, this work presents a comprehensive study on the mechanical properties and fatigue behavior of Al-Cu-Mg alloy subjected to a cyclic plasticity treatment. The cyclic strengthened (CS) samples exhibit a well-balanced combination of strength and ductility due to the formation of nanoscale solute clusters. A systematic and quantitative analysis of the strengthening mechanisms is performed to evaluate the contributions of key microstructural features to the mechanical response. Moreover, the CS samples also demonstrate a significantly higher fatigue ratio and fatigue strength compared to the PA sample, despite exhibiting comparable tensile strength. These improvements are attributed to the absence of weak precipitate-free zones (PFZs) induced as a result of cyclic plasticity, which completely eliminates the pronounced strength differential between the grain interiors and the PFZs observed in the PA state. This microstructural uniformity effect effectively suppresses strain localization under cyclic loading, promotes a more homogeneous strain partitioning, and consequently delays fatigue crack initiation. These findings highlight cyclic plasticity treatment as a promising microstructure design strategy for simultaneously enhancing the mechanical and fatigue properties of high-strength Al alloys.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4054-x
The sluggish kinetics and high onset potentials of the oxygen evolution reaction (OER) at the anode of alkaline water/seawater electrolyzers limit overall energy efficiency. Noble-metal oxides like RuO2 are active but suffer from high cost, agglomeration, and dissolution under oxidizing potentials, especially in chloride-rich electrolytes where competing chloride oxidation reaction (ClOR) occurs. Here, we report a mild two-step dry-wet milling strategy to achieve throughout lattice doping of F− into MnO2 (F-MnO2) and subsequent anchoring of atomically dispersed Ru via Ru–O/F hybrid bonds. The strengthened Mn 3d–O/F 2p hybridization and negative charge shielding of surface F− enhance OER activity/selectivity relative to ClOR and impart superior Cl− tolerance and corrosion resistance. The resulting F-Ru-MnO2-TH electrocatalyst exhibits overpotentials of 280 mV and 200 mV at 10 mA cm−2 in alkaline water and simulated seawater, respectively. It retains ~100% of initial activity after 200 h continuous operation in alkaline media and >95% after 300 h in simulated seawater, significantly outperforming Ru-MnO2 and commercial RuO2. This work provides a scalable route to durable, high-performance OER catalysts for seawater electrolysis.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60631-1
Methane dehydroaromatization (MDA) offers a carbon-neutral route to benzene, toluene, and xylene (BTX), yet the regulatory mechanisms of Brønsted acid site (BAS) strength and spatial proximity to Mo sites remain unresolved. This study systematically tunes BAS strength via isomorphous substitution (Al, Ga, Fe, B) and Mo-BAS proximity in ZSM-5, integrating catalytic evaluations with density functional theory (DFT). Strongly acidic Al-zeolites achieve the highest methane conversion, while weakly acidic B-substituted systems exhibit optimal mono-/bifunctional synergy, outperforming moderate-acid counterparts. DFT reveals that deprotonation energy (DPE) correlates with acid strength; Al-ZSM-5 (DPE = -5.68 eV) lowers the C–H activation barrier (ΔG = 1.467 eV). Spatial proximity analysis shows that nanoscale Mo-BAS distances, achieved via ball milling, enhance methane conversion by 33% and BTX yield by 31% compared to micrometer-scale mixtures, by accelerating intermediate transport and suppressing coke. These findings establish a multi-scale framework linking acid strength, spatial confinement, and electronic modulation, providing actionable guidelines for designing next-generation MDA catalysts.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025102501
Non-antibiotic emerging contaminants (ECs) pose a growing threat to aquatic organisms, particularly fish, yet their impact on gut microbiota remains inadequately characterized. This systematic review synthesizes current evidence on the effects and mechanisms of non-antibiotic pharmaceuticals, pesticides, per- and polyfluoroalkyl substances (PFAS), nanomaterials, and microplastics on fish gut microbiota. Exposure to these ECs directly alters microbial composition and diversity, while indirectly disrupting host metabolism and immune function, leading to significant health impairments. Notably, EC exposure induces dysregulation of key factors such as lipopolysaccharide (LPS), compromising intestinal barrier integrity. Concurrently, gut microbiota can metabolically transform certain ECs into derivatives, establishing a complex pollutant-microbiota-host interaction network. The gut microbiota mediates EC-induced neurotoxicity, immune dysfunction, and metabolic disorders through signaling pathways such as TLR/NF-κB and metabolic homeostasis regulation. Current research predominantly addresses short-term exposure effects, leaving long-term low-dose impacts and transgenerational mechanisms poorly understood. Future investigations should employ multi-generational exposure and microbiota transplantation to elucidate gut microbiota-mediated toxicity mechanisms under non-antibiotic EC stress. This review underscores the urgent need for comprehensive risk assessment and regulatory frameworks targeting non-antibiotic ECs in aquatic environments.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025083003
To obtain freshwater from saline water and seawater, a double-layer evaporator consisting of carbon spheres and corn stalks was fabricated (abbreviated as CC). Corn stalks served as the evaporator substrate, and a mixed hydrogel of carbon spheres and polyvinyl alcohol functioned as the photothermal conversion layer. The solar-driven interfacial evaporation and desalination performance of the CC evaporator was investigated. The glucose-derived carbon spheres exhibited a uniform morphology and achieved 95% light absorption across 200–2500 nm. Under 1 sun (1 kW·m−2) irradiation, the CC with 3 cm height (CC-3) reached an exceptional evaporation rate of 3.55 kg·m−2·h−1 with a remarkable energy efficiency of 97.53%. When different wind speeds (1.5, 2, and 2.5 m·s−1) were applied, the evaporation rates further increased to 7.17, 8.92, and 10.41 kg·m−2·h−1, respectively. The evaporation rate of CC-3 for 3.5% saline was 3.46 kg·m−2·h−1. A 5-day long-time experiment exhibited stable desalination and excellent salt tolerance. Under a wind speed of 2.5 m·s−1, the evaporation rate reached 9.56 kg·m−2·h−1. In an outdoor natural light within a closed system and 2.5 m·s−1 of wind speed, the maximum evaporation rate and cumulative evaporation amount for seawater were 9.59 kg·m−2·h−1 and 66.0 kg·m−2, with no salt crystallization observed on the CC surface. These results demonstrate the potential practical application of the CC evaporator in seawater desalination.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605023
Identifying the characteristics of carbon emissions and driving forces of the railway sector is essential for formulating effective measures to develop a green and low-carbon railway industry. This study systematically evaluated the direct and indirect carbon emissions from 2016 to 2021 generated by the railway sector of China, and analyzed the spatiotemporal dynamic changes of the carbon emissions. On this basis, by adopting the LMDI model, the key factors affecting the carbon emissions of railway sector were discerned. Moreover, the variations in the dominant factors of the carbon emissions over time, and the spatial heterogeneities in the dominant factors of the carbon emissions of the 18 railway bureaus, were analyzed. The results show that: 1) During the periods from 2016 to 2021, the carbon emissions of China's railway sector showed an overall upward trend, increasing from 57.7486 million tons to 64.2084 million tons, by 11.2%. The Shanghai Bureau, Beijing Bureau, Zhengzhou Bureau, Chengdu Bureau and Guangzhou Bureau substantially contributed to the increases of railway carbon emissions. In spatial, the carbon emissions of the 18 railway bureaus were characterized by lower emissions in the west and higher emissions in the east, mainly due to the regional differences in the socio-economic development, industrial structure and population density; 2) During 2016 to 2021, the decline in energy consumption intensity reduced the carbon emissions of the railway sector by 18.8654 million tons, while the changes in carbon emission intensity, economic benefits of per unit passenger and freight turnover, and operating capacity led to an increase of a sum of 25.3252 million tons of carbon emissions. When decomposing the contributions of each factor by sub-periods, it can be found that the impacts of these factors on the carbon emissions changed over time. Only the factor of carbon emission intensity showed a promoting effect in all sub-periods, the other three factors, as energy consumption intensity, economic benefits of per unit passenger and freight turnover, and operating capacity, had a conversion between promoting and inhibiting effects. 3) The dominant factors of carbon emissions across the 18 railway bureaus exhibited spatial heterogeneity. For instance, operating capacity was the main promoting factor for bureaus like Taiyuan, Beijing, Lanzhou, Nanning, Hohhot, Urumqi, and Qinghai-Tibet, while energy consumption intensity was the main inhibiting factor. For Shanghai, Kunming, Wuhan, Chengdu, Xi'an, Zhengzhou, Jinan, Shenyang, Nanchang, and Guangzhou, economic benefits per unit turnover was the main promoting factor, with energy consumption intensity as the main inhibiting factor. For Harbin, energy consumption intensity was the main promoting factor, while economic benefits per unit turnover was the main inhibiting factor. 4) The railway sector can reduce carbon emissions by optimizing transport organization to reduce empty car rates, optimizing energy structure, and retrofitting infrastructure for energy efficiency, while implementing differentiated emission reduction strategies tailored to each bureau's characteristics.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605024
The refined quantification of carbon footprint in engineering construction projects is critical for formulating targeted carbon reduction strategies during the materialization phase. This study integrates material flow analysis (MFA) with the emission factor method to establish a panoramic carbon flow model for engineering projects. Construction activities are categorized into processing and construction, and office and daily operations, clarifying material and carbon flow relationships within the system boundary and with external systems. Empirical analysis was conducted on the Hejiawan Bridge of Section 11 of the Xiyu High-Speed Railway. Results show that the total carbon flow amounts to 27,482,432.11 kg CO2eq, with direct carbon flow (fuel oil, gasoline) accounting for 7.6% and indirect carbon flow (products, transportation, electricity) accounting for 92.4%. From the material flow perspective, the total carbon flow comprises product carbon flow (72.88%), resource and energy carbon flow (25.73%), transportation carbon flow (1.04%), waste carbon flow (0.35%), and service carbon flow (0.01%). In terms of activity scope, construction-related carbon flow accounts for 99.17%, while office and daily operations account for 0.46%. Two indicators, material consumption carbon flow rate and energy consumption carbon flow rate, are proposed for the first time. Comparative analysis of five girder bridges reveals that the Hejiawan Bridge has a material consumption carbon flow rate of 3.91 kg CO2eq/kg, ranking highest among similar bridges, while its energy consumption carbon flow rate is 13.40 kg CO2eq/kg ec, at a medium level. The assessment indicates relatively high material consumption, suggesting potential for carbon reduction through structural and geological optimization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3756-5
Photochemical organic synthesis exploits the distinctive redox properties of excited-state photocatalysts to avoid stoichiometric redox reagents, enabling green and sustainable transformations. However, the conversion efficiency of light-to-chemical energy remains a key bottleneck for large-scale application. Here, we synthesize ultra-thin graphitic carbon nitride (g-C3N4) nanosheets by regulating precursor types and thermal protocols. In photochemical Minisci-type cross-couplings, this ultra-thin carbon nitride exhibits high catalytic efficiency, achieving rates of 40 mmol g_cat−1 h−1 under LED irradiation and 10.9 mmol g_cat−1 h−1 under natural sunlight. The photocatalyst's high specific surface area (120 m2 g−1) enhances substrate adsorption capacity and accelerates surface electron transfer, boosting photocatalytic efficiency. Furthermore, the material demonstrates excellent recycling stability, and the reaction system was successfully scaled to gram-level, highlighting its potential for industrial applications. This work provides a typical case for solar-driven organic synthesis and inspires further developments in heterogeneous photocatalysis.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509067
Marine litter poses a significant threat to coastal ecosystems globally, necessitating a comprehensive understanding of its multi-compartment distribution and driving mechanisms for effective management. This study investigated the occurrence, composition, and sources of beach, sea surface, and seafloor litter in the northeastern Daya Bay, a semi-enclosed bay, during August–October 2024. Sampling included 11 beach transects, 6 surface transects, and 25 seafloor transects. Results showed that the mean density of large and very large beach litter was 4.41×10^5 items·km−2, while medium beach litter reached 5.39×10^6 items·km−2. Surface litter densities were 5.82×10^2 and 9.90×10^3 items·km−2 for large/very large and medium fractions, respectively. Seafloor litter averaged 5.20×10^3 items·km−2. Plastics dominated all compartments, accounting for 74.0% (beach), 96.0% (surface), and 78.8% (seafloor) of total litter. Source apportionment using NOWPAP methodology indicated that beach and surface litter primarily originated from coastal recreational activities, whereas seafloor litter was mainly derived from shipping and fishing. Beach quality assessment revealed that 63.6% of beaches were moderately clean or better (grade II–IV), and 90.9% were moderately safe or better (grade I–III). Hotspots included tourism beaches, tidal gyre areas, coral reef zones, and fishing grounds. The study underscores the need for targeted management, including improved waste collection on tourist beaches, dynamic cleaning protocols, and port reception facilities for fishing waste.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025030501
Coastal areas serve as critical ecological interfaces for the migration of terrestrial microplastics (MPs) into the ocean, and characterizing their pollution is essential for integrated coastal management. This study investigated the occurrence, sources, and ecological risks of MPs in surface waters of nearshore areas and river estuaries around Hainan Island, a typical tropical tourist island. MPs abundance ranged from 316.67 to 1300 n·m−3 in seawater and from 400 to 5416.67 n·m−3 in river water. In seawater, the dominant polymer was polyethylene terephthalate, with fibers being the predominant shape, size class 500–1000 μm, and white/transparent color. In river water, polypropylene-ethylene copolymer dominated, also as fibers, but with size class 100–500 μm and white/transparent color. Seawater MP abundance showed a significant positive correlation with tourist numbers, and distribution across functional areas followed: tourism areas > natural areas > aquaculture areas > residential areas. Multiple correspondence analysis identified household plastic waste, laundry wastewater, aquaculture, and fishery products as primary sources of seawater MPs. Principal component analysis indicated homologous characteristics between seawater and river MPs, suggesting rivers are a major pathway for terrestrial MP transport to coastal zones. Ecological risk assessment revealed low pollution loads, with potential ecological risks moderate for seawater and medium-low for river water. Notably, 15% of seawater sampling sites exhibited polymer risk level Ⅳ, primarily driven by polyacrylonitrile's high biological toxicity. These findings provide a scientific basis for developing MP pollution control strategies in Hainan Island.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3962-y
Photochromic Förster resonance energy transfer (pc-FRET)-based subnanometric polymersomes with accurate color control offer a transformative yet challenging tactic for advanced and custom-tailored information encryption. Herein, various amphiphilic alternating pyrene/azobenzene-containing copolymers were polymerized using one-pot Ugi four-component polycondensation. Subsequent self-assembly was performed to produce highly-integrated monolayer subnanometric polymersomes (MSNPSs) and their composites, with diameters of around ~250 nm and vesicular thicknesses of approximately ~12.0 Å. J-aggregated monolayer chain-folding mechanism was accountable for the donor-acceptor-donor stacking manner within the vesicular membrane, beneficial to achieve highly efficient energy transfer. The trans-to-cis photoisomerization of azobenzenes rendered MSNPSs and their composites with photo-triggered structural transitions in diameter and vesicular thickness. Benefitting from considerable spectral overlap between cis-azobenzene and pyrene, MSNPSs and their composites were capable of photo-controllable non-invasive pc-FRET performance with a wide Stokes shift (~320 nm). The accurate color variation from blue to red highly depended upon precise modulation of both irradiation duration and precursor-fixed donor/acceptor ratios. The proof-of-concept individually multichromatic 2D QR code was attained using photochromic MSNPSs and their composites in patterning lithography, displaying a multimodal decryption and favorable repeatability for high-level and personalized information protection. Our work paves a prospective avenue to meticulously craft stimuli-chromatic polymersomes for the potential of advanced information encryption.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60670-6
Direct conversion of syngas to higher alcohols (C2+ alcohols) is critical for coal-based resource utilization and energy security. Here, a series of Na-modified CoFe/Al2O3 catalysts were synthesized via incipient wetness impregnation and evaluated for syngas-to-alcohol reactions. Multiple characterizations (XRD, N2 adsorption-desorption, H2-TPR, XPS, DRIFTS, in situ Raman, Mössbauer spectroscopy) elucidated synergistic effects of Na and Fe promoters. Na facilitated formation of Co-Fe alloy sites during reaction, while Fe modified electronic state of Co and promoted transformation of lattice oxygen to adsorbed oxygen, increasing surface oxygen vacancies. Synergistic interaction between alloy and carbide sites enhanced CO insertion into olefin intermediates, improving C2+ alcohol selectivity. Under 260 °C and 2 MPa, Co1Fe1Na1 catalyst (n(Co):n(Fe):n(Na)=1:1:1) achieved total alcohol selectivity of 45%, with C2+ alcohols comprising 94.1% of total alcohols. This study provides insights into rational design of Co-based catalysts for efficient syngas conversion to C2+ alcohols.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026012605
Synthetic phenolic antioxidants (SPAs) are widely used, leading to environmental contamination and human exposure. However, studies on their effects on adipocyte differentiation and underlying mechanisms, particularly for emerging SPAs, are limited. This study evaluated the impacts of 4-tert-octylphenol (4-t-OP) and three novel antioxidants (AO 3114, AO 1135, AO 702) on adipogenesis using the mouse 3T3-L1 preadipocyte differentiation model. Lipid staining, triglyceride measurement, differentiation-related gene expression analysis, and transcriptomic approaches were employed. All four SPAs significantly promoted differentiation of 3T3-L1 cells into mature adipocytes and upregulated expression of peroxisome proliferator-activated receptor gamma (Pparγ) and mature adipocyte marker genes. Transcriptomic analysis revealed differential effects on gene transcription during early differentiation. GO and KEGG enrichment analyses indicated that these SPAs promoted adipogenesis by enhancing energy metabolism and protein synthesis, as well as regulating PPAR and other signaling pathways. In conclusion, the tested SPAs promote adipogenesis and disrupt lipid metabolism through distinct mechanisms, suggesting long-term exposure may cause metabolic disorder risks and pose a public health threat.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608009
To investigate the flow and heat transfer characteristics of natural draft direct air-cooling towers (NDC) for large coal-fired power generating units, a three-dimensional CFD numerical model covering major plant buildings, air-cooled radiators, and ambient wind fields was established based on the NDC systems of a 2×660 MW unit of a power plant. The influences of meteorological factors, including ambient wind speed, ambient temperature, and ambient wind direction, as well as regulation measures such as rolling shutters, louvers, and bypass windows on the heat dissipation performance of NDC towers were systematically analyzed. The results demonstrate that ambient wind speed acts as the dominant factor governing the performance of the NDC system. As wind speed rose, the uneven distribution of air intake volume and heat dissipation among each cooling delta increased remarkably, which elevated the unit back pressure, and the upstream tower suffered more severe impacts than the downstream one. Ambient temperature exerted a slight effect on circumferential flow distribution, yet substantially changed the overall back pressure of the system. In terms of regulation strategies, closing rolling shutters in the windward zone and reducing the opening of partial louvers can improve air flow redistribution to a certain extent, but will reduce the total air flow rate and total heat dissipation of the entire tower. By contrast, bottom bypass windows can effectively optimize the air intake on the leeward side and boost heat dissipation under high-wind operating conditions, whereas top bypass windows deliver only limited improvement effects. This research can provide fundamental data and technical references for the optimal design, operational regulation, and energy-saving retrofitting of large NDC units.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4097-3
The on-demand patterning of two-dimensional transition metal dichalcogenides (TMDs) with tailored edges is critical for electronic and optoelectronic applications but remains technically challenging. Here, we report a stress-guided anisotropic etching strategy for producing large-area, well-ordered MoS2 nanostructures, including nano-ribbons and nano-squares, without templates. By applying uniaxial cumulative stress followed by selective thermal etching, MoS2 monolayers are statistically etched into ribbon-like structures whose width inversely correlates with applied stress magnitude. The newly etched edges are macroscopically straight or serrated, predominantly Mo-zigzag terminated, and enhance photoluminescence by a factor of ~8.0. The edge type depends on the angle between stress direction and crystallographic orientation, corroborated by theoretical calculations. Biaxial stressing generates well-defined nano-squares, offering a scalable, versatile patterning route for engineering 2D materials with tailored functional edges, promising for electrocatalytic and optoelectronic applications.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60666-4
The catalytic hydrogenation of CO2 to ethanol is a pivotal technology for carbon neutrality and high-value chemical production. Cobalt-based catalysts, with their unique electronic structure and tunability, are promising for this reaction, yet challenges persist: low single-pass CO2 conversion, ethanol selectivity below 60%, and rapid deactivation. This review systematically analyzes recent progress, establishing the thermodynamic and kinetic framework, and dissecting molecular-level mechanisms, particularly C–C bond formation and controlled oxygen removal. It critically evaluates synergistic effects among metallic Co, Co2C, CoOx, and bimetallic configurations, emphasizing structure-activity relationships influenced by supports and promoters. Inverse catalysts and tandem systems are reviewed, along with water's role as a hydrogen source. The review identifies shortcomings and advocates for advanced in situ/operational characterization and theoretical modeling to guide next-generation catalyst design. Key findings from cited studies include: Co/La4Ga2O9 achieving high selectivity (reference [85]); K-loaded Cu/CoOx boosting ethanol production (reference [86]); Ga-promoted CuCo catalysts with Cu-CoGaOx interfacial sites (reference [88]); and Mo-tailored CoFe alloys suppressing over-carburization (reference [89]). These insights provide a framework for developing efficient cobalt-based systems, deepening mechanistic understanding, and accelerating sustainable ethanol production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4216-7
Flexible Cu2ZnSn(S,Se)4 (CZTSSe) solar cells are promising for lightweight and mechanically pliable photovoltaics, yet their performance is limited by severe non-radiative recombination and residual stress. Here, we report a sealed constant temperature (SCT) annealing strategy that simultaneously optimizes the CZTSSe/CdS heterojunction and alleviates stress. Under uniform mild thermal conditions (85°C, 5 h), SCT annealing promotes gradient diffusion of Cd2+ into the absorber, partially substituting Zn2+, which optimizes band alignment, passivates interface defects, and suppresses near-interface CuZn defects. This reduces open-circuit voltage loss and improves fill factor. The flexible device achieves a power conversion efficiency of 13.07%, a significant improvement over the reference (12.1%). The SCT strategy also enhances mechanical flexibility by reducing residual stress. Our findings provide a controllable route to advance both efficiency and flexibility of flexible CZTSSe solar cells.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4169-9
Transition metal fluorides (TMFs) are promising cathode materials for lithium-ion batteries (LIBs) due to their high theoretical capacity and energy density, yet their practical application is hindered by low utilization rates stemming from particle sizes exceeding the effective Li+ transport distance (<20 nm). This work introduces a multiphase metal fluoride composite (MMFC) synthesized via a hydrothermal method, leveraging high-entropy concepts and interface engineering to enhance electrochemical performance. The MMFC, after annealing at 400°C (MMFC-400), exhibits high specific capacity, excellent rate capability, and cycling stability. The multiphase interfaces accelerate Li+ migration kinetics and provide additional active sites, addressing the limitations of conventional TMF cathodes. This study proposes a multiphase interfacial energy storage strategy for advanced TMF cathodes, offering a pathway to high-performance LIBs.