SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4412-y
GeTe-based thermoelectric materials are promising lead-free alternatives to PbTe, but their intrinsically high Ge vacancy concentration (~10^21 cm^-3) leads to excessive carrier density and degraded Seebeck coefficient. This study integrates resonant levels (RLs) via In doping and local van der Waals gaps via Sb/Bi alloying to decouple electron and phonon transport. The optimal composition Ge0.91Sb0.04Bi0.04In0.01Te exhibits a Seebeck coefficient of ~287.31 μV K^-1 at 323 K, more than double that of the In-free sample (~102.28 μV K^-1). The peak figure of merit zT reaches ~1.8 at 723 K, with an average zT of ~1.0 over 323–723 K. Vickers hardness is enhanced to ~224 HV, a ~93% improvement over pristine GeTe (~116 HV). X-ray diffraction reveals a structural evolution toward a pseudo-cubic phase with increasing In content, and the (202) peak shifts to lower angles, indicating lattice expansion. These results demonstrate that synergistic RLs and van der Waals gaps effectively optimize carrier concentration and suppress thermal conductivity, offering a viable route for high-performance, mechanically robust GeTe thermoelectrics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4283-0
Smart windows are critical for building energy conservation, yet existing technologies cannot simultaneously satisfy the diverse requirements of light transmission, thermal insulation, and privacy protection across varying scenarios, such as daytime transparency and nighttime heat retention with opacity. Herein, we report a thermo- and electro-responsive ionogel fabricated via one-step photopolymerization, integrating the electrochromic viologen derivative (Pa-PhV)(TFSI)2 with a thermoresponsive matrix. The (Pa-PhV)(TFSI)2 delivers excellent electrochromic performance, featuring dual-band light modulation, a high coloration efficiency of 433.6 cm2 C-1, and a fast coloration time of 2.52 s. The ionogel exhibits three stable switchable states under thermal and electrical regulation, fulfilling core practical demands for full-spectrum photothermal management. Model house tests verify its excellent seasonal adaptability, with a maximum indoor temperature reduction of up to 15 °C in a simulated summer environment. Furthermore, the ionogel enables dual-encrypted data storage via UCST and voltage triggering. This work broadens the application scope of viologen derivatives and offers a competitive strategy for multifunctional smart windows and encrypted data storage.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4180-9
Developing highly active and stable electrocatalysts based on the lattice oxygen mechanism (LOM) for the oxygen evolution reaction (OER) represents a significant challenge in water splitting. Herein, we successfully introduce oxygen vacancies (Ov) into high-entropy MnFeCoNiCu layered double hydroxides (HE-LDHs) via a solution chemical reduction method utilizing a defect engineering strategy. By precisely tuning the concentration of oxygen vacancies, we effectively activate the lattice oxygen within the HE-LDHs. The optimized Ov-rich high-entropy LDHs (Ov-HE-LDHs) exhibit excellent OER catalytic performance, achieving a current density of 10 mA cm−2 with a remarkably low overpotential of only 210 mV in 1.0 M KOH electrolyte, which is substantially superior to pristine HE-LDHs (315 mV) and commercial IrO2 (330 mV). Furthermore, the catalyst demonstrates outstanding long-term stability, capable of stable operation for 500 h at a high current density of approximately 200 mA cm−2. Advanced X-ray absorption fine structure analysis elucidates the lower metal valence states, indicating the existence of oxygen vacancies, while isotope labeling experiments and in-situ electrochemical Raman spectroscopy strongly confirm the successful activation of the LOM pathway. Density functional theory calculations further validate that the shift in the OER mechanism towards LOM and the resulting reduction in the reaction energy barrier are the fundamental reasons for the catalyst’s enhanced intrinsic activity. This work proposes a novel strategy for activating lattice oxygen in high-entropy LDHs through defect engineering, offering new insights and experimental guidance for the design and development of highly efficient and stable high-entropy OER electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4232-1
Polyanionic cathode materials are widely considered as potential cathode materials for sodium-ion batteries due to their strong three-dimensional framework and intrinsic thermal safety. Nevertheless, the limitation of the specific capacity and energy density hindered their application, which can be ascribed to the common reliance of single-electron redox reaction of the transition metal. By realizing the reversible double redox reaction of vanadium-based and manganese-based polyanion cathodes, researchers have successfully opened up a new way to break through the long-term performance limitations. Recent studies disclose that vanadium and manganese-based polyanionic cathodes exhibit the possibility of realizing a reversible double-redox reaction, which opened up new avenues to overcome the capacity dilemma. However, many fundamental issues remain unclear, including insufficient structural stability at high operating voltages, irreversible structural evolution induced by sodium extraction, sluggish electronic and ionic transport kinetics, and Jahn–Teller distortion. Therefore, it is imperative to summarize recent work in order to clarify the pathway for future investigation. In this review, the key challenges associated with the activation of the double-redox reaction are outlined, followed by the realization and regulation of the double-redox reaction in polyanionic cathode materials. A systematic summary of recent studies is performed for both vanadium and manganese-based compounds, which could contribute to the fundamental understanding of the double-redox reaction mechanism. Combined with the modification strategy and future perspective, this review provides insights into the rational design of polyanionic cathodes with a reversible double-redox reaction. It also offers insights into the development of high-energy-density cathode materials for next-generation sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3558-4
The development of advanced titanium alloys capable of operating above 600 °C remains a critical challenge for aerospace propulsion systems, where conventional Ti alloys suffer from insufficient high-temperature strength and microstructural instability. Here, we propose a computationally driven design strategy for titanium-based medium-entropy alloys (MEAs) that integrates thermodynamic phase prediction with mechanistically informed strength modeling, enabling systematic exploration of the Ti-Nb-Al-Cr quaternary system. The optimized Ti70Nb10Al15Cr5 MEA exhibits exceptional performance metrics: 18% room-temperature ductility (as-cast), a yield strength of 520.7 MPa at 650 °C (post-aging), and an ultralow density of 4.76 g/cm3 (45% lighter than Inconel 718). Microstructural characterization reveals a metastable single-phase BCC structure in the as-cast state, which transforms into a BCC/Ti3Al dual-phase system upon aging, with temperature-dependent precipitate morphology and phase stability. The alloy demonstrates superior high-temperature strength retention up to 900 °C (>80 MPa yield strength), outperforming commercial titanium alloys (e.g., Ti-1100, TG6) and bridging the performance gap between conventional Ti alloys and nickel-based superalloys. This work establishes a multi-criteria design paradigm for entropy-engineered alloys, offering a viable pathway to lightweight, high-temperature structural materials for next-generation aerospace applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3605-0
Nickel oxide (NiOx) is widely used as a hole transport material in inverted perovskite solar cells (PSCs). However, its practical application is limited by low intrinsic conductivity and insufficient hole extraction ability, leading to significant interfacial defects that reduce device efficiency and stability. To overcome these issues, two isomeric small organic molecules, 2,6-NOT and 1,5-NOT, were developed and introduced to modify NiOx. These isomers share the same structure but differ in the substitution positions of functional groups, resulting in distinct molecular planarity. Experimental results demonstrate that 1,5-NOT, featuring extended conjugation and enhanced planarity, more effectively enhances the hole extraction/transport capabilities and conductivity of NiOx compared to 2,6-NOT. The NiOx/1,5-NOT-based device achieves a remarkable power conversion efficiency (PCE) of 24.20%, along with excellent long-term stability, surpassing the NiOx control device (18.12%) and the 2,6-NOT-based device (21.87%). These findings indicate that modifying NiOx with small organic molecules significantly improves charge transport performance, and increasing molecular planarity is particularly beneficial for enhancing hole transport and reducing defect density, thereby increasing both efficiency and stability. This work provides a new strategy for NiOx modification via small organic molecules, offering a promising route to high-performance inverted PSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3694-3
Lithium metal anodes (LMAs) are among the most promising candidates for next-generation batteries with high energy density. However, their practical application is hindered by persistent challenges such as dendritic lithium growth, unstable solid electrolyte interphases (SEI), and poor Coulombic efficiency. Surface coating has emerged as a viable solution to address these limitations. In particular, atomic and molecular layer deposition (ALD/MLD) techniques offer unparalleled control over the fabrication of ultrathin, conformal coatings, making them especially suitable for stabilizing LMA interfaces. This review comprehensively summarizes recent progress in applying ALD and MLD methodologies to construct durable artificial interphases on LMAs. We discuss the underlying mechanisms through which these coatings inhibit dendrite formation, improve interfacial integrity, and facilitate uniform lithium-ion transport. The roles of inorganic ALD coatings, organic MLD coatings, and their organic–inorganic hybrids are systematically examined, with a focus on their chemical composition, deposition behavior, and electrochemical characteristics. Moreover, we highlight the enhanced performance achieved through the integration of ALD/MLD-engineered interfaces in full-cell systems. The review concludes with a discussion of current challenges and potential research avenues aimed at advancing the rational development of effective LMA protection strategies. Overall, this work offers valuable insights into the role of interfacial engineering via ALD and MLD in enabling the practical deployment of lithium metal batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3603-2
Conventional glass fiber/epoxy (GF/EP) composites, while structurally competent, are hindered by poor interlaminar toughness, low thermal conductivity, and electromagnetic transparency. This study transforms GF/EP composites into advanced structural multifunctional materials by embedding Ti3C2Tx MXene/poly(acrylic acid) (PAA) aerogels (TPA) as integral interlayers. Hybrid composites with tailored architectures—aligned (GFAM_A) and random (GFAM_R) TPA/GF/EP laminates—were fabricated via unidirectional and isotropic freeze-casting, respectively. The integrated aerogel phase promotes crack deflection and distributed energy dissipation, leading to notable enhancements in interlaminar shear strength (ILSS) and fracture toughness. The continuous Ti3C2Tx MXene network within the aerogel creates efficient through-thickness thermal conduction pathways and imparts strong microwave absorption properties. Notably, GFAM_A achieves simultaneous increases of approximately 52% in ILSS, 78% in toughness, and 42% in thermal conductivity, along with effective microwave absorption: a minimum reflection loss of −23.47 dB and a maximum effective bandwidth of 2.70 GHz. This study demonstrates that precision aerogel engineering provides a powerful strategy for upgrading conventional glass fiber composites into advanced multifunctional structural materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3683-y
Effective management of traumatic hemorrhage requires rapid blood loss control and facile removal of hemostatic materials to minimize secondary tissue damage. We fabricated a strongly adhesive aerogel (OPA) via Schiff-base crosslinking of oxidized hyaluronic acid (OHA) and ε-polylysine (ε-PL), enabling rapid hemostasis in lethal arterial trauma and on-demand removal via phase transition. OPAs exhibited tunable porosity and rapid blood absorption. Surface hydroxyl, amino, and carboxyl groups promoted strong hydrogen bonding with tissues, blood cells, and plasma proteins, enhancing tissue adhesion and platelet capture/activation. In a rabbit femoral-artery-injury model, OPA4 shortened hemostatic time by ~80% and reduced blood loss to 38% of the blank group. Notably, OPAs retained only 2% of initial adhesion after hydration, allowing gentle removal. OPAs also demonstrated excellent antibacterial activity, biocompatibility, and biodegradability. The simple one-step freeze-drying process and tailorable shapes offer scalable production and versatile applications. This study provides a versatile strategy for emergency and surgical hemostasis, combining rapid control of life-threatening arterial bleeding with on-demand atraumatic removal, promising improved patient outcomes and streamlined postoperative care.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024110703
Urban river ecosystems are increasingly threatened by anthropogenic activities, necessitating comprehensive health assessments beyond conventional water quality metrics. This study evaluates the ecological health of the Zhongshan South Road reach in Wuhu, China, by integrating microbial community integrity with physicochemical parameters. Nine monitoring sections were established, considering land use, pollution sources, and seasonal hydrology. Over four seasons, eight water quality parameters and microbial indicators were systematically monitored. A Microbial Index of Biotic Integrity (M-IBI) was developed through candidate parameter screening, interference response analysis, and discriminant ability assessment. Core metrics included Chao1 index, Sobs index, and relative abundances of Acinetobacter and hgcl-clade genera. M-IBI scores were standardized and classified into health levels, with results compared against the Water Quality Index (WQI). Findings revealed seasonal M-IBI variation: winter > autumn > summer > spring, with downstream water quality superior to upstream. Spatial and seasonal patterns of WQI and M-IBI were largely concordant, though discrepancies arose from differential microbial responses to environmental factors and heightened sensitivity to human disturbance. The M-IBI approach demonstrated robust applicability for river health assessment, offering a sensitive, integrative tool for urban water management.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3881-y
One-dimensional (1D) and quasi-1D platinum diselenide (PtSe2) exhibit enhanced quantum confinement and surface effects, leading to distinctive electronic and optical properties. However, efficient synthesis of high-quality quasi-1D PtSe2 with controlled dimensionality and orientation remains challenging. Here, we report the first successful synthesis of quasi-1D PtSe2 via a carrier-gas-assisted chemical vapor deposition (CVD) approach. By optimizing hydrogen concentration, we achieved highly oriented and crystalline quasi-1D PtSe2, which exhibits exceptional thermodynamic stability along the (110) crystal plane. Electrical characterization reveals that 2D few-layer PtSe2 exhibits p-type semiconductor properties, while quasi-1D multilayer PtSe2 displays semimetallic behavior. Due to quantum confinement effects, both materials exhibit similar carrier mobilities. In photodetection at 1550 nm, 2D PtSe2 exhibits conventional positive photoresponse with a maximum responsivity of 97.0 A/W. In contrast, quasi-1D PtSe2 demonstrates unique negative photoresponse, achieving a maximum responsivity of 194.2 A/W, attributed to its semimetallic nature and significant surface traps. Temperature-dependent photoresponse measurements at various power levels further confirm that the negative response originates from a defect-assisted photogating effect, the strength of which exhibits significant temperature dependence under high-power illumination. This work not only fills a gap in the synthesis of 1D PtSe2 but also provides a novel material platform for developing advanced infrared optoelectronic devices.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60620-7
Direct coal liquefaction (DCL) diesel constitutes over 60% of DCL products, yet its cetane number (30–40) falls short of the automotive diesel standard (≥45). Rapid and accurate compositional analysis is essential for optimizing properties via component blending. Traditional gas chromatography offers high accuracy but is unsuitable for online industrial monitoring. Near-infrared (NIR) spectroscopy enables rapid, non-destructive analysis, but spectral interpretation is complex. This study integrates NIR spectroscopy with machine learning (ML) to construct a spectral-composition database for DCL diesel. Feature extraction using correlation coefficient and mutual information methods screened key wavelength variables, reducing dimensionality from ~1800 to ~200 wavelengths. Three ML models—Lasso, SVR, and XGBoost—were compared. Excluding spectral data with absorbance >1 significantly improved model accuracy, increasing test set R² from 0.85 to 0.96. After feature extraction, the optimal variable count was 177, enhancing computational efficiency. Among models, SVR-MI-0.9 (mutual information feature selection) achieved the best performance, with training and test set R² values exceeding 0.98, enabling precise prediction of paraffin, naphthene, and aromatic contents. This research provides a robust methodology for intelligent online quality monitoring. An intelligent NIR spectroscopy data analysis software was independently developed based on the established model. Compared with comprehensive two-dimensional gas chromatography, the software reduced analysis time by over 98%, with absolute prediction error below 0.2%. Thus, rapid analysis of DCL diesel components was successfully realized.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010608
This study investigated the occurrence and distribution of 27 per- and polyfluoroalkyl substances (PFAS) in surface water and sediment of the Fuchun River, a tributary of the Qiantang River Basin. Surface water samples were analyzed using ultra-performance liquid chromatography coupled with high-resolution mass spectrometry. Total PFAS concentrations (∑PFAS) in surface water ranged from 30.04 to 105.26 ng/L, with mean and median values of 59.64 ng/L and 51.43 ng/L, respectively. The dominant compounds were perfluorooctanoic acid (PFOA), hexafluoropropylene oxide dimer acid (GenX), and perfluorobutanoic acid (PFBA). Concentrations generally decreased from upstream to downstream, consistent with previous studies. Notably, GenX levels were significantly elevated compared to earlier reports. In sediment, ∑PFAS concentrations ranged from not detected (ND) to 0.59 ng/g dry weight, with mean and median values of 0.14 ng/g and 0.11 ng/g, respectively. PFOA and perfluorooctanesulfonic acid (PFOS) were the primary sediment contaminants. Source apportionment indicated that industrial wastewater discharge and sewage treatment plant effluents were the main sources of PFAS in the river. Risk assessment using risk quotients suggested low ecological risks to aquatic organisms for most detected PFAS. However, the presence of short-chain and novel PFAS warrants further investigation due to potential unknown risks.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3818-4
The electrocatalytic reduction of carbon dioxide (CO2RR) to multi-carbon (C2+) products is of significant interest due to its implications for chemical manufacturing and carbon neutrality. However, the competitive hydrogen evolution reaction (HER) and sluggish C–C coupling kinetics impede selectivity at industrial current densities. Here, we report an interfacial nanoconfinement strategy using N-(2-acetamido)iminodiacetic acid (ADA) to engineer a series of capping layer-covered Cu catalysts (Cu@ADA-x). A volcano-type correlation between capping layer thickness and C2+ selectivity is observed. The optimized Cu@ADA-m catalyst achieves a maximum Faradaic efficiency for C2+ products (FE C2+) of 86.8% and maintains over 80% of its initial FE C2+ after 42 hours at 200 mA cm−2, with an energy efficiency of 38.5%. In-situ Raman spectroscopy and density functional theory (DFT) calculations reveal that the capping architecture stabilizes metastable Cu species and optimizes gas adsorption, enhancing *CO intermediate utilization and lowering C–C coupling energy barriers. This work provides a catalyst design principle for industrial-scale carbon-neutral electrochemical production of multi-carbon products.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3798-x
Ulcerative colitis (UC) is a chronic inflammatory disorder of the colorectal mucosa, where conventional enema therapies suffer from poor retention and limited inflammation modulation. Here, we report a highly fluid probiotic-containing enema solution (s-BSA-Fe+EcN) integrating bovine serum albumin (BSA), Fe2+, and probiotic Escherichia coli Nissle 1917 (EcN). The solution's high fluidity enables comprehensive coverage of irregular colorectal mucosa. Upon encountering reactive oxygen species (ROS)-rich inflamed lesions, Fe2+ mediates H2O2 scavenging and hydroxyl radical generation, triggering BSA crosslinking and in situ gelation into a conformal hydrogel (h-BSA-Fe+EcN). This targeted adhesion mitigates oxidative damage to host tissues and preserves probiotic viability. In a porcine model, endoscopic imaging confirmed inflammation-targeted gelation in vivo. In a dextran sulfate sodium-induced mouse colitis model, h-BSA-Fe+EcN demonstrated excellent therapeutic efficacy, reducing disease activity index and restoring colonic architecture. This strategy addresses the dual challenges of fluid perfusion and rapid ROS-responsive gelation, offering an advanced transanal treatment for UC.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509049
This study systematically compared three virus enrichment and concentration methods—polyethylene glycol (PEG) precipitation, aluminum salt coagulation, and centrifugal ultrafiltration—for detecting SARS-CoV-2 in high-turbidity, high-strength wastewater from inbound flights. The aluminum salt coagulation method exhibited the best overall performance, achieving an average recovery rate of 25.95% for SARS-CoV-2 pseudovirus, significantly higher than PEG precipitation (12.91%) and centrifugal ultrafiltration (0.22%) (P<0.05). Its detection limit reached 10 copies·mL⁻¹, whereas centrifugal ultrafiltration suffered severe membrane fouling, limiting detection to 1,000 copies·mL⁻¹. Considering the high pH buffering of flight wastewater, the aluminum salt method was optimized by adjusting pH to 6.00±0.4, employing rapid magnetic stirring, and reducing mixing time to 1 minute, yielding an average recovery of 27.56% (not significantly different from the original 25.95%, P>0.05). An automated enrichment device was developed based on the optimized method, reducing processing time per sample from 115 min to 60 min while maintaining comparable recovery and improved repeatability. Applied to 1,309 wastewater samples from inbound flights between January 2024 and May 2025, the average detection rate of SARS-CoV-2 was 45.45%, with trends consistent with national COVID-19 epidemiological data. The automated device demonstrates suitability for routine surveillance, providing technical support for port epidemic prevention.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509019
To enhance the electricity generation and decolorization efficiency of bioelectrochemical systems (BES) for azo dye wastewater, this study introduced pomelo peel biochar as anode material and flavonoid-rich Chinese herbal medicines as electron mediators (EMs) into microbial fuel cells (MFCs). The anodes were prepared by chemical activation with KOH, ZnCl2, and H3BO3, followed by polypyrrole (PPy) modification. Among the modified anodes, PPy-PPCH3BO3-CC exhibited the best electrochemical performance. The EMs were derived from aqueous extracts of Scutellaria baicalensis (Huangqin), Ginkgo biloba leaves, and Pueraria lobata (Gegen). The extract from Scutellaria baicalensis showed the highest electron transfer capability. In the MFC system equipped with the optimal anode and Scutellaria baicalensis extract, the maximum output voltage reached (587±10) mV, power density increased to 423.12 mW·m−2, Coulombic efficiency was (57.85±1.06)%, COD removal efficiency was (77.45±0.92)%, charge transfer resistance (Rct) decreased to 7.15 Ω, and methyl orange decolorization rate reached (95.86±1.12)%. These results were significantly superior to the control group, demonstrating that natural source materials can effectively enhance the performance of BES for methyl orange wastewater treatment.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60636-6
Polyoxymethylene dimethyl ethers (DMMx) are promising clean diesel additives. Compared to the traditional aldol condensation route, the one-step oxidative method for producing DMMx directly from methanol is a green synthesis route offering significant advantages. However, due to the complexity of the reaction, a balance must be struck between oxidation depth and C–O chain growth efficiency. This imposes specific requirements on the design of catalysts with multifunctional active sites: the catalyst should possess appropriate oxidative activity, suitable acid strength distribution, and effective synergy between these two functions. To address these challenges, this study designed a sulfuric acid-modified molybdenum-doped NASICON catalyst, which demonstrated favorable catalytic performance in the one-step oxidative synthesis of DMMx from methanol. Over the NSC-Mo-0.5-30% catalyst, methanol conversion rate of 81.3% and the DMMx selectivity of 58.7% were achieved, along with the formation of heavier molecules, as evidenced by the DMM2–6 selectivity of 11.3%. The NH3-TPD, Py-IR and XPS results indicate that the introduction of molybdenum increases the number of weak Lewis acid sites, while sulfuric acid impregnation not only generates gradient-distributed Brønsted acid sites but also promotes the formation of Mo5+/Mo6+ redox pairs. The cooperation of the two types of active sites significantly enhances catalyst performance.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60654-8
The declining costs of renewable energy are progressively improving the economic viability of employing electrochemical techniques for carbon dioxide capture. Electrochemical carbon capture (ECC) technology utilizes electrical energy to drive electrode reactions, enabling the selective separation of CO2. The vigorous development of ECC powered by renewable energy offers a promising alternative route to conventional carbon capture methods, overcoming limitations associated with thermally driven capture and release cycles. This approach provides a promising alternative route that is more efficient, flexible, scalable, low-energy-consuming and low-polluting for traditional carbon capture technologies. This review begins by introducing established, large-scale carbon capture technologies, such as pre-combustion capture, post-combustion capture, oxy-fuel combustion, adsorption, membrane separation and the calcium looping process. It then transitions to several rapidly developing ECC technologies, including electrochemically mediated amine regeneration (EMAR), pH-swing-mediated systems, and methods involving redox-active molecules. The pH-swing systems are further categorized into bipolar membrane electrodialysis (BMED), proton-coupled electron transfer (PCET), and membrane capacitive deionization (MCDI). For each method, the underlying principles, technological advancements, advantages, as well as current problems and challenges, are systematically elucidated. It is anticipated that with the widespread deployment of green electricity and persistent innovation in electrochemical materials, ECC technology will emerge as a highly efficient and low-carbon strategy, contributing significantly to the global goal of achieving carbon neutrality.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606008
Resin-enhanced electrosorption for water treatment significantly improves ion adsorption efficiency and selectivity through synergistic effects, making it a research hotspot in the water treatment field. This technology provides an innovative solution to the bottlenecks of kinetic lag and insufficient selectivity by modulating electrode-solution interface behavior in multiple dimensions. Current technological advances include the following: a simple integration method enables desalination efficiency to exceed 92.3%; resin-coated composite electrodes eliminate the co-ion effect and achieve a 42% increase in total salt adsorption capacity; resin-derived porous carbon electrodes with tunable pore structures possess three to five times the adsorption capacity of commercially available activated carbon; and by enhancing solution convection and electrophoretic convection, the resin-filling strategy achieves a high desalination rate of (670 ± 20) mg/(L·h). Studies have demonstrated that different material combinations can achieve targeted optimization of adsorption performance based on specific water quality characteristics. Future research directions may focus on: developing intelligent resin materials with electromagnetic responsiveness; constructing a multi-scale structural design theory for resin-electrode systems; and establishing a cross-scale model integrating electrochemistry, fluid dynamics, and interface science for comprehensive analysis. In particular, in-depth studies are needed on the dynamic behavior of resin-based flow electrodes under electric/magnetic field regulation, as well as the precise construction of catalytic sites on the resin surface. This review aims to promote the widespread application and efficient practice of this technology in water treatment, providing a theoretical foundation and scientific basis for the future development of high-efficiency, selective, and stable electrosorption technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3874-1
The rapid expansion of artificial intelligence (AI) model sizes to trillions of parameters has intensified the demand for computational paradigms that overcome the von Neumann bottleneck. Emerging memory technologies, while advancing, fall short of meeting the massive requirements of large-scale models. Ferroelectric materials, with their continuous tunability of domain patterns, offer a promising route to emulate synaptic weights in biological learning. This review systematically examines four fundamental ferroelectric-based device architectures: ferroelectric capacitors, ferroelectric field-effect transistors (FeFETs), ferroelectric tunnel junctions (FTJs), and ferroelectric domain wall memories. We analyze their latest progress, application domains, and inherent advantages, while critically assessing the challenges impeding their commercialization. Key issues include scalability, endurance, retention, and integration with CMOS technology. We also highlight optimization strategies for material and device performance, array-level design, and neuromorphic computing architectures. Future research directions are proposed, emphasizing the expansion of novel applications and the realization of energy-efficient, high-density in-memory computing systems. This review provides a comprehensive framework for researchers and engineers aiming to harness ferroelectric devices for next-generation computing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3986-2
Organic/molecular ferroelectrics exhibiting spontaneous polarization have attracted increasing attention due to their flexibility, light weight, low-temperature processability, environmental friendliness, and biocompatibility. Among them, organic donor-acceptor cocrystals, self-assembled from two or more components, offer new insights into ferroelectricity. This review systematically examines recent progress in organic donor-acceptor cocrystal ferroelectrics, focusing on microscopic origins of ferroelectricity, structure modulation strategies, and underlying mechanisms. Ferroelectric origin mechanisms, including intermolecular charge transfer, proton transfer, and order-disorder transitions, are analyzed in detail. Structure-property relationships in crystal engineering are summarized, and recent advances in theoretical simulations, experimental characterization techniques, and practical applications are introduced. Finally, current challenges and future research perspectives are outlined. The review highlights that weak intermolecular interactions often lead to low Curie temperatures (Tc), limiting practical applications. Strategies to enhance Tc involve introducing stronger molecular interactions to increase transition energy barriers. Notably, room-temperature ferroelectricity in organic cocrystals has been achieved, as demonstrated by Wiscons et al. (Angew Chem Int Ed, 2018, 57: 9044–9047). The review underscores the potential of organic cocrystal ferroelectrics for flexible and wearable electronics, while addressing the need for higher Tc and robust switching performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3813-y
Sonothermal therapy (STT) is an emerging noninvasive energy-based modality that leverages deeply penetrating ultrasound to activate engineered nanomaterials, converting acoustic energy into localized heat. This review systematically delineates four coupling routes between ultrasound and nanomaterials: thermoelastic, thermoviscous, and plasmonic heating; nonradiative recombination and acousto-electric coupling; thermal vibrations in carbon and conjugated systems; and cavitation heating. Design principles for STT nanomaterials are established, with guidance for pre-, intra-, and post-treatment phases, and linked to applications in tumor ablation, wound infection and healing, and implant-associated infection and regeneration. Hybrid platforms integrating STT with sonodynamic or sonocatalytic reactive oxygen species generation are discussed. Key translational barriers include the lack of quantitative and standardized metrics for conversion efficiency, the need for scalable and reproducible manufacturing aligned with Good Manufacturing Practice, limited in vivo biodistribution and biosafety data, and weak links from preclinical models to clinical endpoints. An integrated framework connecting mechanism, material design, and therapeutic outcome is proposed to guide the development of next-generation STT nanoplatforms for treatment-resistant disease.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3889-6
Photocatalytic hydrogen production is fundamentally limited by inefficient charge separation and asynchronous supply of electrons and protons to active sites. Here, we designed a ZnIn2S4/ZnCo2S4 (ZIS/ZCS) heterojunction with an atomically coherent interface achieved via an ultralow lattice mismatch of 0.05%. This unique structure promotes rapid electron transfer through a built-in electric field and facilitates continuous proton migration via a hydrogen spillover effect, thereby synchronizing electron and proton delivery at the catalytic interface. This dual regulation of electrons and protons synergistically promotes proton-coupled electron transfer, resulting in a high hydrogen evolution rate of 70.3 mmol g−1 h−1 and selective oxidation of benzyl alcohol to aldehyde (39.3 mmol g−1 h−1) with 93.6% selectivity. This work demonstrates the critical importance of lattice match and dual charge-proton management in designing efficient photocatalysts for complex redox reactions.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3925-5
Capacitive pressure sensors have garnered significant attention in electronic skin, human-machine interaction, health monitoring, and medical devices due to their remarkable properties like highly sensitive pressure perception, good repeatability, and rapid response capabilities. However, manufacturing capacitive pressure sensors that simultaneously achieve a broad linear detection range and high sensitivity remains a significant challenge. Herein, a novel hierarchically interlocked capacitive pressure sensor (HI-CPS) was designed by integrating a stretchable polyethylene glycol (PEG)-based nanofilm dielectric layer with hierarchically interlocked microstructures, demonstrating excellent linearity and high sensitivity over a wide sensing range. HI-CPS based on a one-layer nanofilm exhibits ultrahigh sensitivity (9.40 kPa−1) and an ultralow detection limit (0.1 Pa). When the dielectric layer comprises two layers of stacked nanofilms, the sensor not only maintains high sensitivity (3.17 kPa−1) but also achieves excellent linearity (R2 = 0.999) over a broad working range (<5 kPa), along with remarkable stability even after 10,000 cycles. Benefitting from the outstanding comprehensive performance, HI-CPS has been proven to be successfully implemented in monitoring various human biological signals, sign language recognition, and basketball shooting gesture correction. This strategy of assembling the tailored nanofilm with structural engineering has significant potential application in building high-performance pressure detection and recognition devices.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511020
With the increasing number of oil pipelines crossing rivers, the potential risks of oil leakage and surface spreading to river ecosystems and water environments are becoming more severe. Scenario-based simulation of oil spill diffusion is a prerequisite for effective interception point placement and leakage risk prevention. Numerous factors influence oil spill diffusion, including environmental conditions, river hydrology, and accessibility of emergency resources. This study integrates these factors and multiple dynamic processes to design eight typical scenarios for oil spill diffusion simulation, considering emergency resource locations, river hydrological regimes, and leakage modes. A case study is conducted on an oil pipeline crossing a river in northwest China. Results indicate that the diffusion distance and affected area are primarily controlled by water conditions and emergency resource accessibility. In emergency management, the efficiency of maintenance and repair resources during high-water months should be prioritized. Mechanistically, external forces such as hydraulic and wind forces have a greater influence on diffusion distance, surpassing internal forces like gravity, viscosity, and surface tension within a short time. For river crossings near emergency resources, internal force effects should be considered in oil spill diffusion simulations. When emergency resource arrival times are long, the diffusion distance based on Fay's theory is relatively small and can be neglected in engineering practice. This study provides a computational basis and methodological reference for risk assessment and emergency response to potential oil spills from pipelines crossing rivers, enhancing the scientific and effective nature of risk prevention and emergency handling.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607013
This study investigated the synergistic effects of earthworm mucus and two biochar types (rice husk biochar and straw biochar) on heavy metal bioavailability during sludge composting. Sludge was amended with earthworm mucus alone or combined with biochars at varying proportions, and the impacts on physicochemical properties, total heavy metal concentrations, bioavailable fractions, and chemical speciation were analyzed. Results showed that mucus addition increased sludge pH and electrical conductivity (EC) but decreased total nitrogen (TN) and total phosphorus (TP) contents. Synergistic mucus-biochar composting further elevated pH and EC while reducing TN, with the optimal treatment being mucus plus 10% rice husk biochar. Mucus-only composting reduced total concentrations and bioavailability of Cd, Cu, Ni, Zn, and Pb. Adding biochars significantly enhanced these reductions. Specifically, mucus with rice husk biochar achieved the best Cd removal, with total and bioavailable Cd decreasing by 27.03%–55.68% and 9.52%–28.57% (P<0.05), respectively, compared to controls. Mucus with straw biochar was most effective for Ni, Zn, and Pb, reducing total contents by 3.81%–5.72%, 7.93%–34.62%, and 42.61%–79.46%, and bioavailable fractions by 2.90%–26.31%, 15.58%–24.14%, and 32.30%–36.88% (P<0.05), respectively. Speciation analysis revealed that Cd, Ni, and Pb carbonate-bound fractions transformed into residual forms, and exchangeable fractions shifted to Fe-Mn oxide-bound forms. Straw biochar addition resulted in the highest residual fractions for Cd, Cu, Ni, Zn, and Pb, increasing by 0.35%–7.02%, 8.61%–12.90%, 16.62%–23.02%, 17.33%–26.10%, and 16.12%–27.20% (P<0.05), respectively. These findings demonstrate that earthworm mucus combined with rice husk or straw biochar effectively reduces heavy metal concentrations and bioavailability in sludge, offering a promising strategy for sludge composting.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3825-x
Polymer-based dielectric materials with high energy density and thermal stability are critical for modern electric/electronic industries. Polyimide (PI) based materials are promising due to their high temperature resistance and chemical inertness, yet their inherently low dielectric constant and limited charge-discharge energy density restrict applications in film capacitors. While incorporating ferroelectric or conductive fillers can enhance dielectric performance, batch-to-batch inconsistency and physical deterioration remain problematic. This study focuses on molecular structure design and modulation, preparing hyperbranched polyimides with different dianhydride monomers and branching degrees. The effects of chain packing density with polar groups on dielectric and energy storage performances were systematically investigated via experimentation and molecular simulation. Results demonstrate a significant correlation between monomers' electrical distribution and packing density in polymer systems. Molecular simulation further elucidated the underlying mechanism. This work establishes a foundation for designing polymer-based dielectric materials with high dielectric and energy storage performances at the molecular level.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042504
This study investigated the effect of co-aging with common cations/anions and humic acid (HA) on the combined use of Vallisneria natans (VN) and lanthanum-modified bentonite (LMB) for controlling phosphorus (P) release from sediment. Results showed that co-aging significantly reduced the phosphate adsorption capacity of LMB, with the maximum unit adsorption capacity decreasing by 33.8% compared to the unaged material. Under the combined application of VN and unaged LMB, P in sediment could still be released into pore water via dissimilatory iron(III) reduction mediated by iron-reducing bacteria and chemical reduction of iron(III) induced by sulfate-reducing bacteria metabolites, subsequently migrating to overlying water. However, the combined treatment effectively inhibited P release, achieving an average reduction efficiency of 57.1% for dissolved reactive phosphorus (SRP) in overlying water and 74.0% for labile P in sediment (measured by DGT) at an LMB dosage of 89 g·m−2. Co-aging with common ions and HA diminished the P control efficiency of the combined treatment, primarily due to reduced phosphate adsorption capacity of LMB. Therefore, mitigating the negative effects of co-aging is crucial for enhancing the long-term P control performance of the VN-LMB combined technology.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4075-1
Titanium alloys, such as Ti-6Al-4V (TC4), are indispensable in aerospace, biomedical, and advanced manufacturing due to their high specific strength, corrosion resistance, and biocompatibility. However, their inherent strength-ductility trade-off and limited stiffness hinder next-generation lightweight structural applications. Traditional ceramic reinforcements (TiC, TiB2, SiC) improve strength but introduce brittleness and interfacial incompatibility, degrading plasticity and fatigue resistance. Graphene, with theoretical strength ~130 GPa and Young's modulus ~1 TPa, offers a promising two-dimensional reinforcement. This review systematically examines graphene-reinforced titanium matrix composites (TMCs), focusing on the intrinsic relationship between preparation, microstructure, and properties. Key preparation routes include powder metallurgy and additive manufacturing, with challenges in achieving uniform dispersion and controlling interfacial reactions. Recent studies demonstrate that surface modification and process optimization can form an ideal interface structure comprising a nano-TiC layer and residual graphene. Even at low graphene additions, synergistic strengthening mechanisms—load transfer, fine-grain strengthening, and Orowan dislocation bypass—significantly enhance strength, hardness, and wear resistance while preserving ductility. This review consolidates critical theoretical and experimental findings, offering guidance to overcome technological bottlenecks and promote engineering applications of graphene-reinforced TMCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3998-8
Constitutional isomerism in covalent organic frameworks (COFs) has emerged as a powerful strategy to tailor material properties for photocatalytic applications. Here, we report the design and synthesis of two isomeric multicomponent COFs (MC-COFs) via Schiff-base condensation followed by Povarov reaction, converting imine linkages into quinoline structures. These isomeric MC-COFs exhibit opposing C=N bond orientations and distinct phenyl group alignments within the COF pores, leading to different torsion angles in the COF layers. Structural analyses reveal that enhanced planarity promotes π-π stacking and electron delocalization, resulting in favorable band structures and reduced exciton binding energies. Consequently, the optimized COF achieves a superior hydrogen peroxide (H2O2) production rate of 3128 μmol g−1 h−1 under visible light irradiation. This work underscores the critical influence of structural isomerism on the photocatalytic efficiency of MC-COFs and provides insights for rational design of high-performance COF-based photocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4146-8
The conventional trial-and-error approach for the research and development (R&D) of high-performance super-hydrophilic coatings presents long-standing challenges, including data scarcity, unclear structure-activity relationships, and lack of design guidelines. In this study, an innovative multi-model framework that synergistically integrates a specialized polymer large language model (PolyLLM) and a polymer machine learning model (PolyML) for intelligent R&D of super-hydrophilic coating systems is designed and demonstrated. During the hydrophilic polymer research phase, the multi-model leverages the domain-specific insights and chemical tool capabilities of the fine-tuned PolyLLM to systematically screen 852 hydrophilic monomers and generate 3880 hypothetical polymer architectures. By utilizing the PolyML, the multi-model enables precise performance predictions and quantitative evaluations of feature importance to facilitate efficient high-throughput screening of optimal structures from the generated polymer database. Experimental validation confirms that the multi-model achieves a mean absolute error (MAE) below 10% across various polymer property prediction tasks compared to experimental data. This approach leads to the rapid discovery of hydrophilic polymers with exceptional anti-swelling and wear-resistance. In developing super-hydrophilic coatings, the multi-model effectively combines PolyLLM's guidance for large-scale synthesis with PolyML's capabilities for precise formulation optimization and curing parameter adjustments. The effectiveness of multi-model is demonstrated by the accelerated development of high-performance anti-fogging coatings for swim goggles and optical films with outstanding water- and wear-resistance that significantly outperform leading commercial products. This multi-model offers a flexible approach for advanced polymer coatings, leading to a seamless connection between laboratory research and industrial development.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4215-3
The escalating demand for energy-efficient edge inference in artificial intelligence has intensified the search for hardware that transcends the von Neumann bottleneck. Ferroelectric field-effect transistors (FeFETs) are promising due to their non-destructive readout, low programming energy, and multilevel operation. However, integrating ultrathin ferroelectrics with two-dimensional (2D) channels remains challenging due to the inert surfaces of 2D materials, which impede uniform film growth. Moreover, conventional ferroelectrics like doped hafnia and AlScN suffer performance degradation at thicknesses required for sub-1V operation. The interface between ferroelectric and 2D semiconductor is often plagued by traps and parasitic layers, causing threshold drift and fatigue. In a recent Science report, Hailin Peng and colleagues present an innovative solution: a native ferroelectric buffer derived from the semiconductor itself. By oxidizing layered Bi2O2Se below 400°C, they produce wafer-scale α-Bi2SeO5, a van der Waals ferroelectric oxide. This material retains robust ferroelectricity down to the monolayer limit, supporting both out-of-plane and in-plane polarization switching. It exhibits a high relative dielectric constant (~24) and a Curie temperature near 880 K. The in-situ oxidation approach enables precise thickness control, yielding a uniform, switchable, and robust gate stack for 2D FeFETs, addressing the critical challenges of voltage scaling and interface quality.