SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4433-5
Negative thermal expansion (NTE) and zero thermal expansion (ZTE) materials are technologically relevant for precision engineering, yet their practical deployment is constrained by narrow operating temperature windows. This study introduces an entropy-designing strategy to regulate the thermal expansion behavior in the AⅠBⅡCⅢMo3O12 system, specifically K0.4(Mg0.25Mn0.25Co0.25Ni0.25)0.4Sc1.6Mo3O12 (CE0.4MO) and related CExMO compositions (x = 0.4, 0.6, 0.8, 1.0). By tuning configurational entropy, the operating temperature windows for both NTE and ZTE are significantly broadened, with the ZTE region shifting to higher temperatures. Among single-phase compositions, CE0.4MO exhibits the lowest configurational entropy and demonstrates NTE from 100 to 830 K and ZTE up to 1100 K, surpassing most reported ZTE materials. Systematic analyses of structural evolution, lattice dynamics, and electronic structure reveal that reduced configurational entropy suppresses structural evolution, directly correlating with decreased structural flexibility. Higher atomic displacement parameters (ADPs) of oxygen in CE1.0MO provide experimental evidence for enhanced flexibility. Raman spectroscopy shows that the full width at half maximum (FWHM) of peaks in the 750–900 cm-1 range positively correlates with configurational entropy, indicating reduced lattice disorder, while modes within 750–1050 cm-1 blue-shift as entropy decreases, confirming lattice stiffening. Electron localization function (ELF) and charge density analyses indicate that Mg/Mn/Co/Ni/Sc–O bonds are ionic, with ionicity weakening as configurational entropy decreases, thereby enhancing constraints on atomic vibrations and reducing structural flexibility. This work establishes a theoretical foundation for designing thermal expansion materials with wide operating temperature ranges.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4360-7
Polarization-sensitive photodetection is critical for advanced optical communication and imaging systems, yet conventional photodetectors suffer from low on-off ratios and limited polarization discrimination. Here, we report gate-tunable PdSe2/WSe2 van der Waals heterostructures that achieve ultrahigh light on-off ratio and polarization-sensitive photodetection. The heterostructure forms a type-II band alignment, enabling efficient charge separation and self-powered operation. By applying a gate voltage, the photoresponse can be modulated, achieving an on-off ratio exceeding 10^6 under illumination. The device exhibits a high responsivity of 1.2 A/W and a specific detectivity of 10^12 Jones at room temperature. Polarization-sensitive measurements reveal a linear dichroism ratio of 2.1 at 532 nm, attributed to the anisotropic crystal structure of PdSe2. The photodetector operates over a broad spectral range from visible to near-infrared (400-1000 nm) with fast response times (rise/fall < 100 μs). The gate-tunable capability allows dynamic control of the photocurrent, enabling adaptive sensing applications. These results demonstrate that PdSe2/WSe2 heterostructures are promising candidates for high-performance, polarization-sensitive photodetectors, offering a pathway for next-generation optoelectronic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4212-x
Idiopathic pulmonary fibrosis (IPF) is a lethal interstitial lung disease with limited therapeutic options. Current treatments, such as nintedanib and pirfenidone, target downstream fibrosis but fail to address the upstream drivers, including persistent alveolar epithelial injury and abnormal repair. This study presents an inhalable, reactive oxygen species (ROS)-responsive liposomal system (SAB/GC-1@Lip-cRGD) that co-delivers the antioxidant salvianolic acid B (SAB) and the thyroid hormone receptor β (TRβ) agonist Sobetirome (GC-1). The liposomes are surface-modified with cRGD peptides for targeted delivery to fibrotic lesions and possess a negative surface charge to enhance mucus penetration. In the high-ROS fibrotic microenvironment, the liposomes destabilize, releasing SAB and GC-1. SAB scavenges ROS to remodel the fibrotic niche, while GC-1 reactivates TRβ signaling, driving the differentiation of stalled Krt8+ transitional epithelial cells into functional alveolar type I (AT1) cells. In a mouse model of pulmonary fibrosis, SAB/GC-1@Lip-cRGD significantly reduced pro-inflammatory cytokines (TNF-α, IL-1β, IL-6) and TGF-β1 in bronchoalveolar lavage fluid and lung homogenates. The proportion of CD206+ M2 macrophages decreased from 27.4% in the model group to 6.2% after treatment, indicating potent anti-inflammatory and anti-fibrotic effects. This synergistic strategy of microenvironment remodeling and epithelial regeneration achieved robust collagen depletion, restoration of alveolar integrity, and recovery of pulmonary function, outperforming single-drug or non-targeted formulations. The work provides a generalized paradigm for integrating microenvironment regulation with regenerative repair in pulmonary diseases.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4232-1
Polyanionic cathode materials are widely considered as potential cathode materials for sodium-ion batteries due to their strong three-dimensional framework and intrinsic thermal safety. Nevertheless, the limitation of the specific capacity and energy density hindered their application, which can be ascribed to the common reliance of single-electron redox reaction of the transition metal. By realizing the reversible double redox reaction of vanadium-based and manganese-based polyanion cathodes, researchers have successfully opened up a new way to break through the long-term performance limitations. Recent studies disclose that vanadium and manganese-based polyanionic cathodes exhibit the possibility of realizing a reversible double-redox reaction, which opened up new avenues to overcome the capacity dilemma. However, many fundamental issues remain unclear, including insufficient structural stability at high operating voltages, irreversible structural evolution induced by sodium extraction, sluggish electronic and ionic transport kinetics, and Jahn–Teller distortion. Therefore, it is imperative to summarize recent work in order to clarify the pathway for future investigation. In this review, the key challenges associated with the activation of the double-redox reaction are outlined, followed by the realization and regulation of the double-redox reaction in polyanionic cathode materials. A systematic summary of recent studies is performed for both vanadium and manganese-based compounds, which could contribute to the fundamental understanding of the double-redox reaction mechanism. Combined with the modification strategy and future perspective, this review provides insights into the rational design of polyanionic cathodes with a reversible double-redox reaction. It also offers insights into the development of high-energy-density cathode materials for next-generation sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3558-4
The development of advanced titanium alloys capable of operating above 600 °C remains a critical challenge for aerospace propulsion systems, where conventional Ti alloys suffer from insufficient high-temperature strength and microstructural instability. Here, we propose a computationally driven design strategy for titanium-based medium-entropy alloys (MEAs) that integrates thermodynamic phase prediction with mechanistically informed strength modeling, enabling systematic exploration of the Ti-Nb-Al-Cr quaternary system. The optimized Ti70Nb10Al15Cr5 MEA exhibits exceptional performance metrics: 18% room-temperature ductility (as-cast), a yield strength of 520.7 MPa at 650 °C (post-aging), and an ultralow density of 4.76 g/cm3 (45% lighter than Inconel 718). Microstructural characterization reveals a metastable single-phase BCC structure in the as-cast state, which transforms into a BCC/Ti3Al dual-phase system upon aging, with temperature-dependent precipitate morphology and phase stability. The alloy demonstrates superior high-temperature strength retention up to 900 °C (>80 MPa yield strength), outperforming commercial titanium alloys (e.g., Ti-1100, TG6) and bridging the performance gap between conventional Ti alloys and nickel-based superalloys. This work establishes a multi-criteria design paradigm for entropy-engineered alloys, offering a viable pathway to lightweight, high-temperature structural materials for next-generation aerospace applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3767-9
Progressive skin fibrosis ultimately results in irreversible contractures, causing both joint dysfunction and cosmetic deformity. The key pathological features of skin fibrosis include persistent inflammation and abnormal accumulation of the extracellular matrix (ECM), with epithelial-mesenchymal transition (EMT) playing a critical role in disease progression. However, current therapeutic strategies for cutaneous fibrosis are largely palliative and often require repeated interventions, with limited efficacy. Celastrol (Cel) exerts anti-inflammatory and anti-fibrotic effects in skin tissue, but its clinical application is limited by poor bioavailability and a narrow therapeutic window. Tetrahedral framework nucleic acid (tFNA), a novel nanocarrier system, exhibits multiple advantages, including enhanced cellular uptake, improved cell viability, and intrinsic anti-fibrotic and anti-inflammatory properties. Therefore, this study applied tFNA-Cel complex (TCC) as an advanced nanotherapeutic agent, designed to exert a synergistic anti-fibrotic effect. In this study, an in vitro model of skin fibrosis was established using human keratinocyte (HaCaT) cells treated with 5 ng mL−1 transforming growth factor beta (TGF-β) for 24 h. The results showed that TCC significantly inhibited EMT progression by reducing α-smooth muscle actin (α-SMA) levels and increasing E-cadherin level. Compared to tFNA or Cel alone, TCC exhibited superior anti-fibrotic effects in the fibrosis model, as evidenced by modulation of SMAD family member 2 (SMAD2) signaling and collagen I expression. Furthermore, the TCC group showed lower levels of nuclear factor κB p65 (NF-κB p65), BCL-2-associated X protein (Bax), and reactive oxygen species (ROS) compared to the Cel or tFNA groups. These findings highlight TCC as a promising treatment for skin fibrosis, with its synergistic anti-fibrotic effects providing new therapeutic avenues.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506005
The escalating generation of medical waste, driven by healthcare expansion and frequent medical activities, poses significant environmental and public health risks. Under the framework of ecological civilization, China is developing a comprehensive policy system for medical waste treatment and disposal, yet the current framework remains nascent and exhibits inconsistencies between national and local policies. This study systematically analyzes the status of national and local policies from 2003 to 2024, collecting 413 policy documents (166 from national ministries and 247 from provincial governments). The analysis examines temporal evolution, regional distribution, and policy focus, alongside the influence of medical waste output, treatment technologies, facility infrastructure, and major epidemic responses. Findings reveal distinct policy phases: initial self-disposal, exploratory management, foundational system building, and rapid development. Regional disparities are pronounced, with eastern coastal areas showing more advanced policies due to greater technical and financial resources. The surge in medical waste, particularly during the COVID-19 pandemic, underscores the need for enhanced regulatory guidance. Non-incineration technologies are gaining traction for their environmental and cost benefits, and facility coverage has improved but remains uneven. The study proposes five policy principles to foster technological innovation and industrial upgrading, ensuring safe medical waste management and environmental protection.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507054
In many Chinese wastewater treatment plants (WWTPs), residual chlorine is still manually monitored at low frequencies, leading to imprecise disinfectant dosing. This study systematically compared four machine learning models—backpropagation (BP) neural network, long short-term memory (LSTM) neural network, random forest (RF), and support vector regression (SVR)—for predicting chlorine consumption (i.e., the difference between chlorine dose and residual chlorine) during non-monitoring periods under different residual chlorine monitoring frequencies (every 1, 2, 4, 6, and 8 h). Using data from Plant A (equipped with online residual chlorine monitoring) and Plants B and C (manual monitoring every 6 h and 8 h, respectively), input variables included online water quality indicators (temperature, flow, NH3-N, CODCr, TP, TN) and chlorine dose. Results showed that at 1-h intervals, LSTM achieved the highest prediction accuracy; at 2–4-h intervals, RF performed best; at 6-h or lower frequencies, BP was superior; SVR performed worst across all frequencies. Validation on Plants B and C confirmed BP's optimal performance under low-frequency conditions, and particle swarm optimization (PSO) significantly improved its accuracy. These findings provide a basis for selecting appropriate machine learning models for chlorine consumption prediction under varying monitoring frequencies, particularly low-frequency manual monitoring, thereby supporting precise disinfectant dosing control.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506031
The production of activated carbon from waste biomass such as cyanobacteria from Lake Taihu represents a promising resource utilization route. However, existing studies are mostly confined to laboratory scale, and the gap between laboratory processes and industrial production hinders the evaluation of technical feasibility and economic viability. This study optimized the process for producing cyanobacteria-based columnar activated carbon by co-processing cyanobacteria with garden waste (sawdust), and validated the process on an engineering-scale production line with a daily capacity of 5 t of raw materials. Economic feasibility was also assessed. Results showed that the optimized activated carbon exhibited a particle strength of 91.3% and a specific surface area of 571.44 m2·g−1. The engineering-scale line processed 5 t of raw materials daily, yielding approximately 1.18 t of activated carbon with stable quality: strength of 94.3% and specific surface area of 471.42 m2·g−1, featuring a microporous-dominant structure with coexisting micropores and mesopores. Cost analysis indicated a production cost of 3,595.65 CNY per ton of activated carbon, demonstrating favorable economic benefits. This work provides a basis for larger-scale production and application of cyanobacteria-based activated carbon.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010203
The production and disposal of lithium batteries release not only hazardous metals and particulates but also substantial amounts of harmful organic pollutants. This study focuses on N-methyl-2-pyrrolidone (NMP) to investigate the environmental release and human exposure of organic pollutants throughout the lithium battery lifecycle. Using liquid chromatography-high-resolution mass spectrometry (LC-HRMS), NMP was quantified in environmental samples from battery production and dismantling facilities, as well as in pyrolysis products from simulated thermal recovery of mainstream lithium batteries. Key release stages were identified: slurry mixing and coating/drying during production; shredding, electrolyte volatilization, and high-temperature pyrolysis during disposal. In unprotected occupational settings, estimated NMP exposure via dust ingestion exceeded reference doses, underscoring the need for health impact assessments and evaluation of protective measures. This research provides critical insights into the environmental release and population exposure of organic pollutants across the lithium battery lifecycle, informing health policy for vulnerable populations.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604009
Biological nitrogen removal in wastewater treatment plants (WWTPs) is often limited by insufficient influent carbon sources, necessitating external carbon addition to enhance denitrification. Conventional single carbon sources, such as sodium acetate, frequently fail to meet the metabolic demands of complex microbial communities, compromising nitrogen removal efficiency and stability. Composite carbon sources, by providing multiple electron donors, can improve metabolic cooperation among microorganisms, yet their underlying microbial mechanisms remain insufficiently understood. In this study, activated sludge from a municipal WWTP was used to investigate the microbial mechanisms of composite carbon sources during denitrification. Batch denitrification experiments were conducted in combination with metagenomic and metatranscriptomic analyses to systematically characterize microbial community structure and functional gene expression under different carbon source conditions. Results showed that, compared with sodium acetate as the single carbon source, the composite carbon source system (sodium acetate: sodium succinate: ethanol = 2:1:3) increased the denitrification rate from (6.822 ± 0.141) mg/(L·h) to (8.370 ± 0.186) mg/(L·h), representing a 22.7% improvement, while reducing N2O accumulation by approximately 55%. Metagenomic analysis revealed that Ottowia, Rubrivivax, Thauera, and Zoogloea were the dominant denitrifying genera. Metatranscriptomic results further demonstrated that the composite carbon sources significantly upregulated the transcription of key denitrification genes, with nirS, norB, and nosZ increasing by 37.8%, 27.4%, and 48.6%, respectively. In addition, the composite carbon sources promoted complementary carbon metabolic strategies among different microbial communities, enhancing electron donor supply and improving denitrification efficiency. These findings indicate that composite carbon sources synergistically enhance denitrification performance through regulation of functional gene transcription in complex microbial communities, providing a theoretical basis for carbon source optimization in WWTPs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3745-1
Short-wavelength infrared (SWIR) organic photodetectors (OPDs) have attracted considerable attention due to their potential to overcome the limitations of inorganic counterparts. However, developing organic semiconductors with strong SWIR detection remains a significant challenge. Herein, we design and synthesize a new conjugated pyrrolic polysquaraine (PSQ-COT) by integrating a pyrrolic squaraine unit with a strong electron-donating moiety, achieving an absorption onset extending to 1.2 μm. To evaluate its detection performance, we fabricated two types of PSQ-COT-based SWIR OPDs with PC61BM and BTP-eC9 as the electron acceptors, respectively. The resulting PSQ-COT:PC61BM OPD exhibited superior detection performance compared with the BTP-eC9 counterpart, achieving an impressive specific detectivity of 1.08 × 10^12 Jones at 1030 nm under zero bias. This enhanced performance is due to the lower degree of energetic disorder and reduced trap density in the PSQ-COT:PC61BM device. Furthermore, we successfully integrated the PSQ-COT:PC61BM OPD into a high-pixel-density image array (640 × 512 pixels), enabling clear matter identification under SWIR light irradiation. This work provides valuable insights into designing high-performance organic semiconductors for SWIR light detection and imaging applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3464-4
Photocatalytic conversion of atmospheric CO2 (0.03%) into multi-carbon fuels remains a grand challenge due to the high energy barrier of C–C coupling and the low concentration of CO2. Here, we report the construction of multiple metal pair sites on metal oxide nanosheets to steer C–C coupling, enabling efficient photoreduction of air-concentration CO2 to ethane (C2H6). As a prototype, Au nanoparticles were anchored on Bi4Ti3O12 nanosheets (Au-Bi4Ti3O12). High-resolution transmission electron microscopy and X-ray photoelectron spectroscopy confirmed the formation of Au-Ti metal pair sites at the interface. In situ Fourier transform infrared spectroscopy revealed the presence of *OCCOH intermediate on Au-Bi4Ti3O12 during CO2 photoreduction, which was absent on pristine Bi4Ti3O12. Density functional theory calculations showed that the Gibbs free energy for *CO–COH formation on Au-Bi4Ti3O12 is 2.23 eV, significantly lower than that on Bi4Ti3O12 (3.59 eV), indicating facilitated C–C coupling. Consequently, Au-Bi4Ti3O12 exhibited a C2H6 evolution rate of 2.58 μmol g−1 h−1 under 0.03% CO2, whereas Bi4Ti3O12 produced only C1 products (CO and CH4). This work demonstrates the first single-catalyst photoreduction of atmospheric CO2 to C2H6, highlighting the effectiveness of engineered multiple active sites in overcoming the C–C coupling bottleneck.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61113-4
Porous pyrolytic carbon (PPyC) serves as the buffer layer in TRi-structural ISOtropic (TRISO) fuel particles, providing storage for fission gases, preventing damage to outer layers, and absorbing stresses caused by fuel-kernel swelling. However, the changes of PPyC micro- and meso-structure at high temperatures remain insufficiently understood. In this study, PPyC fabricated by chemical vapor deposition was heat-treated from 1200 to 1600 °C and characterized across atomic-to-mesoscopic scales. Results show that the structure changes with temperature with a transition at approximately 1400 °C. Below 1400 °C, a decrease in Raman ID/IG ratio, narrowing of the graphite diffraction peak, and increased sp2 hybridization indicate progressive ordering associated with defect redistribution. Concurrent decreases in true density and mesopore volume, together with increased closed porosity, are consistent with partial conversion of open pores into closed pores. Above 1400 °C, increased ID/IG ratio, broadening of the diffraction peak near the rhombohedral graphite (101) reflection, and transition regions between crystalline and amorphous material observed by TEM indicate increasing structural disorder. Meanwhile, initially distinct PPyC particle boundaries blur and merge into broad, plate-like domains. Subsequent decrease in closed porosity and increase in mesopore surface area are consistent with partial connection of closed pores to the open-pore network. This work shows that intrinsic coupling between atomic-scale structural change and mesoscale pore connectivity provides a basis for assessing high-temperature structural stability of PPyC in TRISO fuel particles.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61116-X
A standardized dataset of linear sweep voltammetry (LSV) curves is presented for evaluating the oxygen reduction reaction (ORR) performance of carbon-supported catalysts in acidic media. All electrochemical tests were conducted in O2-saturated 0.5 mol L−1 H2SO4 at controlled rotation speeds using a rotating disk electrode. The dataset comprises 120 validated entries from both non-precious metal (MNC) and platinum-based (Pt-MC) catalysts, including original LSV curves and extracted performance parameters such as onset potential, half-wave potential, and limiting current densities at different rotation speeds. Data processing involved potential conversion to the reversible hydrogen electrode (RHE) scale, background subtraction, outlier removal, and reproducibility checks with defined quality control thresholds (relative standard deviation ≤2% for E1/2 and ≤5% for limiting current). The standardized collection serves as a reliable benchmark for catalyst performance comparison, supports kinetic and mass transport analysis, and provides a structured data source for machine learning applications in electrocatalysis. The dataset is openly available via Science Data Bank, with a DOI, and is intended as a dynamic resource for the ORR electrocatalysis community.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0029
Pingshuo coal ash, characterized by high silicon-aluminum content (Si+Al >85%) and low Si/Al ratio (<1.5), exhibits ash fusion temperatures (AFTs) exceeding 1550 °C, rendering it unsuitable for entrained-flow gasifiers. This study investigates the effect of calcium-sodium composite flux on ash fusibility and mineral transformation. X-ray diffraction (XRD) and FactSage thermodynamic simulations were employed to analyze mineral evolution, while molecular dynamics (MD) simulations revealed the underlying melting mechanism. Results show that adding 20% composite flux (CaO/Na2O) lowers AFTs more effectively than equivalent additions of CaO or Na2O alone, indicating a synergistic effect. At a CaO/Na2O ratio of 3:7, the flow temperatures (FT) of two Pingshuo coal ashes decreased to 1377 °C and 1279 °C, respectively. The composite flux promotes reactions between quartz and Na2O/CaO, forming low-melting-point minerals such as nepheline, albite, and gehlenite, while inhibiting mullite formation. Additionally, Na+ disrupts the silicate network, inducing Ca2+ to preferentially coordinate with [AlO4]5- tetrahedra, further breaking Si-O-Si bonds. MD simulations show that atomic diffusion, quantified by mean square displacement (MSD), is significantly enhanced below 1600 K with composite flux addition compared to single fluxes. These findings provide a mechanistic basis for optimizing flux formulations to enable efficient gasification of high-AFT coals.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010802
Ozone (O3) pollution is a prominent issue in the Guanzhong Plain, necessitating effective control of its precursors, particularly volatile organic compounds (VOCs). However, studies on VOC pollution characteristics at the county level are scarce. To investigate the summer VOC pollution characteristics and sources in high-altitude towns of the Guanzhong Plain, continuous monitoring of 53 typical VOC species was conducted at two sites in Changwu County, Xianyang City (elevation 1200 m). The spatiotemporal variations of ambient VOCs and their ozone formation potential (OFP) were analyzed, and source apportionment was performed using the Positive Matrix Factorization (PMF) model. Results showed that average total VOC (TVOCs) concentrations at the Changwu Government and Changwu Middle School sites were 60.04×10⁻⁹ and 83.28×10⁻⁹, respectively. Oxygenated VOCs (OVOCs) dominated, accounting for 55.14% and 62.91% of TVOCs, followed by alkenes, aromatic hydrocarbons, and halogenated hydrocarbons. Industrial sources contributed the most (43.2%) to VOC emissions in Changwu County, but site-specific differences were observed: the Government site was primarily influenced by solvent use (30.7%) and motor vehicles (19.1%), while the Middle School site was dominated by domestic sources (27.6%) and motor vehicles (20.0%). The average OFP values at the Government and Middle School sites were 258.84×10⁻⁹ and 378.04×10⁻⁹, respectively, with alkenes and OVOCs as the main contributors, originating from industrial emissions, solvent use, and biogenic sources. EKMA curves indicated that Changwu County was in a VOC-limited regime during the observation period, confirming the effectiveness of VOC control for ozone mitigation. These findings provide scientific guidance for local ozone management and offer a paradigm for precise ozone pollution control in county-level regions of the Guanzhong Plain.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3854-7
The tertiary spatial structure of biological macromolecules determines their physiological functions. In the formation of the tertiary structure, the secondary structure serves as the assembly foundation, and interactions between secondary structures play a critical role in driving and stabilizing the tertiary architecture. Synthetic foldamers, characterized by their modifiability and structural diversity, can adopt various helical conformations, enabling them to mimic natural protein secondary structures such as the α-helix, while also providing chemical models for studying interactions between secondary structures. This review outlines recent advances in aromatic foldamers and supramolecular helical assemblies formed by helical polymers, with particular attention to unique chiral phenomena observed during the formation of helical secondary structures. It provides a detailed summary of their applications in molecular recognition, ion channels, and circularly polarized luminescence, among others, and discusses future challenges facing aromatic foldamers. The review emphasizes the hierarchical nature of chirality—from primary atomic asymmetry to quaternary higher-order structures—and highlights the importance of understanding non-covalent interactions between helical secondary structures for regulating chiral assembly. Key strategies for constructing chiral helical aromatic foldamers include the use of chiral side chains, terminal groups, and solvent effects, as well as the sergeants-and-soldiers effect and majority-rules principle for chirality amplification. The applications of these foldamers in asymmetric catalysis, chiroptical materials, and biomimetic ion transport are also discussed, underscoring their potential in advanced functional materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3798-x
Ulcerative colitis (UC) is a chronic inflammatory disorder of the colorectal mucosa, where conventional enema therapies suffer from poor retention and limited inflammation modulation. Here, we report a highly fluid probiotic-containing enema solution (s-BSA-Fe+EcN) integrating bovine serum albumin (BSA), Fe2+, and probiotic Escherichia coli Nissle 1917 (EcN). The solution's high fluidity enables comprehensive coverage of irregular colorectal mucosa. Upon encountering reactive oxygen species (ROS)-rich inflamed lesions, Fe2+ mediates H2O2 scavenging and hydroxyl radical generation, triggering BSA crosslinking and in situ gelation into a conformal hydrogel (h-BSA-Fe+EcN). This targeted adhesion mitigates oxidative damage to host tissues and preserves probiotic viability. In a porcine model, endoscopic imaging confirmed inflammation-targeted gelation in vivo. In a dextran sulfate sodium-induced mouse colitis model, h-BSA-Fe+EcN demonstrated excellent therapeutic efficacy, reducing disease activity index and restoring colonic architecture. This strategy addresses the dual challenges of fluid perfusion and rapid ROS-responsive gelation, offering an advanced transanal treatment for UC.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606013
The A2/O-MBR process, owing to its superior effluent quality and smaller footprint, is increasingly adopted in newly built and upgraded wastewater treatment plants. However, systematic studies on its greenhouse gas (GHG) emissions remain scarce, and direct comparisons with the conventional A2/O process are lacking. In this study, two full-scale wastewater treatment plants employing the A2/O and A2/O-MBR processes under identical influent conditions, climate, and discharge standards were investigated. A high-frequency monitoring system covering the entire treatment train was established, and combined with measurements of dissolved CH4 and N2O, water quality parameters, and operational parameters, to elucidate the differences in GHG emission characteristics. Results showed that the daily average CH4 emission intensities were not significantly different between the two plants [(0.67 ± 0.22) and (0.65 ± 0.18) g/m3, respectively]. CH4 emissions mainly originated from sewer-derived anaerobic production and subsequent release in the pretreatment units (accounting for over 70% of the total emissions), with partial in-plant oxidation by methanotrophs. Temperature and aeration-induced stripping were identified as key driving factors, as CH4 emissions were positively correlated with ambient temperature and dissolved oxygen (DO). In contrast, more than 90% of N2O emissions occurred in the biological treatment units. The A2/O-MBR plant exhibited significantly higher daily N2O emission intensity [(0.132 ± 0.055) g/m3] than the A2/O plant [(0.060 ± 0.046) g/m3], largely due to intensive aeration and oxygen-enriched internal/external recirculation in the membrane tank, which enhanced N2O production and stripping. Correlation analysis further revealed that N2O emissions in the A2/O plant were positively related to influent COD and BOD5, indicating dominance of heterotrophic denitrification, whereas in the A2/O-MBR process they were mainly driven by NH3-N loading and DO, reflecting a nitrification-based pathway. Importantly, both processes exhibited CH4 and N2O emission factors that were significantly lower than the reference values recommended by the IPCC and industry guidelines, underscoring the necessity of localizing emission factors for accurate carbon accounting.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3944-9
Hard carbon (HC) is a promising anode material for sodium-ion batteries (SIBs) but suffers from low initial Coulombic efficiency (ICE) and unstable solid electrolyte interphase (SEI). Here, we report a dual-functional strategy combining surface engineering and solution chemical pre-sodiation. A graphitic carbon coating on HC acts as a conductive buffer network and shields surface defects, while sodium biphenyl (Na-Bp) pre-sodiation drives sodium ions into the material via a potential difference, inducing a pre-SEI layer that matures into a thin, dense, NaF-rich inorganic SEI during cycling. This approach compensates for irreversible sodium loss and enhances cycling stability. The pre-sodiated electrode (pCH4-HC) achieves an ICE of 99.5% and a reversible capacity of 321.7 mAh g−1, compared to 54.2% for untreated HC. Long-term cycling shows 74.0% capacity retention after 1000 cycles at 300 mA g−1. In full-cells with NaNi1/3Fe1/3Mn1/3O2 (NFM) cathode, pCH4-HC||NFM delivers 81.9 mAh g−1 after 100 cycles, demonstrating excellent stability and rate performance. This dual-strategy approach validates the adaptability of pre-sodiation technology for high-performance SIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3869-7
Iontronic capacitive pressure sensors (ICPSs) are pivotal for wearable technology, yet their performance is constrained by an inherent trade-off between sensitivity and detection range. Here, we introduce a micro-electric double layer (micro-EDL) engineering strategy to overcome this limitation. This is realized through a nanocomposite dielectric where multi-walled carbon nanotubes (MWCNTs) form a percolated network, generating a dense array of pressure-responsive nano-capacitors. Synergistically integrating a hierarchical MoS2/NiCo-LDH electrode provides abundant pseudocapacitive interfaces. The resulting sensor exhibits an ultrahigh sensitivity of 67,095 kPa−1 at 1 kHz, a broad detection range up to 1.3 MPa, rapid response and recovery times of 4 ms and 5 ms, respectively, and outstanding durability exceeding 18,000 cycles. Practical validation demonstrates 100% classification accuracy in recognizing complex gestures and gait patterns, underscoring its real-world applicability. These findings establish micro-EDL engineering as a promising route for advancing next-generation iontronic devices, offering insights into their electrochemical mechanisms.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511020
With the increasing number of oil pipelines crossing rivers, the potential risks of oil leakage and surface spreading to river ecosystems and water environments are becoming more severe. Scenario-based simulation of oil spill diffusion is a prerequisite for effective interception point placement and leakage risk prevention. Numerous factors influence oil spill diffusion, including environmental conditions, river hydrology, and accessibility of emergency resources. This study integrates these factors and multiple dynamic processes to design eight typical scenarios for oil spill diffusion simulation, considering emergency resource locations, river hydrological regimes, and leakage modes. A case study is conducted on an oil pipeline crossing a river in northwest China. Results indicate that the diffusion distance and affected area are primarily controlled by water conditions and emergency resource accessibility. In emergency management, the efficiency of maintenance and repair resources during high-water months should be prioritized. Mechanistically, external forces such as hydraulic and wind forces have a greater influence on diffusion distance, surpassing internal forces like gravity, viscosity, and surface tension within a short time. For river crossings near emergency resources, internal force effects should be considered in oil spill diffusion simulations. When emergency resource arrival times are long, the diffusion distance based on Fay's theory is relatively small and can be neglected in engineering practice. This study provides a computational basis and methodological reference for risk assessment and emergency response to potential oil spills from pipelines crossing rivers, enhancing the scientific and effective nature of risk prevention and emergency handling.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60615-3
Co-pyrolysis of oil-rich coal and biomass is a promising route to enhance oil and gas production, yet the underlying synergistic mechanisms remain poorly understood. This study investigates the effect of hydrothermal pretreatment (HTP) on the co-pyrolysis of Huangling coal (H) and enzymatic hydrolysis lignin (E). Raw and pretreated samples were characterized via proximate/ultimate analysis, SEM, ICP-OES, and 13C-NMR. Fixed-bed pyrolysis experiments were conducted to evaluate synergistic performance. Results show that HTP reduces oxygen content, develops pore structure, and increases concentrations of inorganic metal ions (Ca, K, Fe) in the aqueous phase. Structural modifications bring the carbon skeleton of E closer to that of H, with increased bridge carbon ratio and improved thermal stability, aligning pyrolysis temperature ranges. For the H/E blend (8:2) after 24 h HTP, tar yield increases by 80.52% compared to untreated blend, with significant rises in aliphatic compounds and monocyclic aromatic hydrocarbons. Gas yields of H2, CO, and CH4 increase by 5.47%, 10.98%, and 9.27%, respectively, while CO2 and pyrolysis water generation are inhibited (water yield decreases by 93.98%). Semi-coke pore structure becomes more developed. The enhanced synergistic effect is attributed to a multi-fold mechanism of 'component interaction-structural modification-catalytic cracking'. These findings provide theoretical support for developing technologies to improve co-pyrolysis of oil-rich coal and biomass, advancing low-carbon, high-quality utilization.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0034
Catalytic cracking of gasoline and diesel to light olefins is a pivotal route for high-value utilization of surplus fuels, typically employing zeolite catalysts. This study systematically investigates the effects of zeolite type and acidic properties on the catalytic cracking of dodecane, a diesel model compound, using SAPO-34, ZSM-5 with SiO2/Al2O3 ratios of 38, 85, and 200, and USY. Catalysts were characterized by XRD, SEM, N2 physisorption, NH3-TPD, and pyridine-FTIR, and evaluated in a fixed-bed reactor. Results demonstrate that zeolite type is the primary determinant of conversion and product distribution. SAPO-34, with 0.38 nm pores, achieved only 24.33% conversion and negligible BTX yield, with severe external coking. ZSM-5-38 and USY, with larger pores, achieved near-complete conversion; however, ZSM-5-38, possessing moderate acidity, yielded the highest light olefins (18.40%) and minimal coke (0.18%), while USY, with higher acidity, promoted hydrogen transfer and coking (12.90% coke). Within ZSM-5 series, lower acid site density (ZSM-5-200) proved optimal, achieving 97.79% conversion and a total light olefin yield of 41.93% (ethylene 11.11%, propylene 20.33%, butenes 10.49%) with low coke (0.43%). The study proposes reaction pathways and regulatory mechanisms, highlighting that zeolite type and acidity govern the relative rates of cracking, hydrogen transfer, oligomerization, aromatization, and coking, thereby dictating performance. These findings provide a rational basis for optimizing zeolite catalysts in commercial gasoline/diesel cracking processes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3980-y
Organic solar cells (OSCs) have achieved power conversion efficiencies (PCEs) exceeding 20% in laboratory-scale devices, yet challenges persist in developing cost-effective charge-transporting materials (CTMs) that ensure high performance and long-term stability. Conventional organic CTMs such as PEDOT:PSS and PDINN suffer from thermal instability due to molecular diffusion and phase segregation. Solution-processed metal oxides (MOs) offer excellent stability and cost-effectiveness but are plagued by surface defects, particularly hydroxyl groups, which act as recombination centers and photocatalytic sites, degrading device interfaces. Here, we develop an organic-inorganic hybrid strategy to homogeneously passivate solution-processible semiconducting MOs. By first synthesizing MOs rich in surface hydroxyl groups and then introducing organic molecules, we achieve chemically homogeneous passivation that mitigates surface defects. This approach enables favorable interfacial energy level alignment, enhanced charge extraction, and tunable surface energy. Employing these passivated MOs as electron transport layers (ZnO) and hole transport layers (NiOx), we achieve a champion PCE of 20.22% for all-MO CTM-based OSCs, the highest reported to date. Scalability is demonstrated via ambient blade-coating, yielding 18.33% PCE for large-area cells (1.44 cm2) and 16.03% for modules (20.05 cm2), with material costs estimated at only 4% of organic counterparts. Furthermore, devices exhibit outstanding stability, retaining over 80% of initial PCE after 1300 h of maximum power point tracking and over 1000 h of thermal annealing at 85°C. This work establishes a new benchmark for cost-effective, high-performance organic photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4079-4
Utilization of ultrahigh-nickel LiNi_xCo_yMn_1-x-yO_2 (NCM) (x > 0.97) in Li-ion batteries can distinctively boost energy density through enhanced discharge capacity. However, capacity and thermal stability deteriorate as Ni content approaches the limit. Here, we propose a facile strategy by introducing high-valence tungsten (W) into ultrahigh-nickel polycrystalline LiNi_0.98Co_0.01Mn_0.01O_2 (PCNCM98). W-doped PCNCM98 (W-PCNCM98) exhibits refined, compactly stacked primary particles, whereas PCNCM98 shows equiaxial, non-uniform larger particles. The refined microstructure enhances mechanical strength: average particle hardness of W-PCNCM98 is 104 MPa, 1.5 times higher than PCNCM98 (68 MPa). This improved mechanical property suppresses lattice volume changes and relieves microcrack formation from H2–H3 phase transition. Consequently, cycling performance in pouch-type full cells is significantly enhanced, with capacity retention of 73% after 2000 cycles at 1 C and 25 °C, 54% higher than PCNCM98. Enhanced structural stability and strong electron affinity of W6+ also improve thermal stability: exothermic peak for W-PCNCM98 is postponed to 203 °C with heat generation of 1287 J g−1, versus 190 °C and 1528 J g−1 for PCNCM98. This high-valent doping strategy stabilizes ultrahigh-nickel NCM cathodes, accelerating large-scale EV applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3921-2
Moisture-enabled energy harvesting technologies offer a promising route for self-powered strain sensing, yet conventional generators suffer from slow response, poor recovery, and limited multidirectional resolution. Here, we report a stretchable thermoplastic polyurethane (TPU) nanofiber moisture-enabled electric generator (MEG) with highly aligned ion channels. A carbon black/sodium dodecylbenzene sulfonate (CB/SDBS) layer is coated on the TPU membrane, while carboxymethyl cellulose (CMC) and acidified poly(sodium 4-styrenesulfonate) (HPSS) are applied on opposite sides, establishing lateral hydrophilicity and ion gradients to drive directional ion migration. The planar MEG is lightweight, flexible, and requires no fully covered electrodes, enabling conformity to complex deformations. The aligned channels reduce ion migration tortuosity, enhancing ion transport efficiency and flux. As a result, the aligned MEG (ATMEG) delivers 0.2 V and 0.51 μA cm−2 at ~90% relative humidity, corresponding to 400% and 287% enhancements compared with the unaligned MEG (UATMEG). The ATMEG also exhibits ultrafast response (0.16 s) and recovery (0.08 s). Utilizing its anisotropic characteristics, a multidirectional self-powered strain sensor is developed, capable of distinguishing both the amplitude and direction of human motion, demonstrating strong potential for adaptive wearable electronics and intelligent motion monitoring.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511027
Aquaponics systems integrate aquaculture and hydroponics to recycle resources, yet nutrient recovery from aquaculture sludge remains inefficient. This study investigated anaerobic acidification as an alternative to conventional anaerobic digestion, which suffers from long conversion cycles. Batch experiments compared two sludge loading rates: high (13.22 kg·kg−1) and low (4.61 kg·kg−1) (mass of sludge per mass of anaerobic inoculum). Under low loading, soluble chemical oxygen demand (SCOD) exhibited a single peak, reaching a maximum organic solid conversion of 68.2% at 70.5 h. In contrast, high loading produced three SCOD peaks with an average peak conversion efficiency of only 26.9% at 27.5 h and higher residual concentrations. Ammonia nitrogen conversion was slightly higher under low loading (64.8%) than high loading (62.2%), while orthophosphate conversion was markedly superior (95.7% vs. 76.4%). The optimal hydraulic retention time for low-loading operation was 144 h, corresponding to an organic loading rate of 0.77 kg·(kg·d)−1. Under these conditions, the produced ammonia and phosphate can be effectively recovered without adversely affecting water quality, as the biofilter converts ammonia to nitrate for plant uptake. Microbial analysis revealed that low-loading conditions favored the dominance of Acinetobacter (relative abundance 66.6%), which likely enhances organic degradation and nutrient release. These findings demonstrate that anaerobic acidification under low loading is a promising strategy for efficient nutrient recovery in aquaponics, offering a shorter conversion time and higher nutrient yields than traditional methods.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511046
To evaluate the carbon footprint differences between the emerging ex-situ remediation facility mode and the conventional on-site remediation mode in China, this study employed the SEFA tool to calculate greenhouse gas (GHG) emissions and energy consumption for four typical remediation scenarios. Results indicate that the carbon emission intensity of solidification/stabilization (S/S) in the remediation facility is 12.00% higher than that of on-site S/S, with unit carbon intensities of 66.74 and 59.59 kgCO2e·m−3, respectively, and total energy consumption 11.90% higher. The soil transport segment in the facility S/S contributes 13% of carbon emissions, being the primary reason for its higher total carbon footprint. Conversely, thermal desorption (TD) in the facility exhibits 11.10% lower carbon emissions than on-site TD, with unit intensities of 269.16 and 302.78 kgCO2e·m−3, and total energy consumption 3.97% lower, mainly due to the utilization of landfill biogas as renewable energy for heat and power generation, while soil transport contributes only 3% of emissions. The reagent segment in S/S and the heat supply segment in TD account for 77%–86% and 70%–72% of total GHG emissions, respectively. The study demonstrates that remediation facilities, leveraging advantages such as landfill biogas, can actively aggregate contaminated soil from surrounding areas for centralized thermal desorption, which is beneficial for regional carbon emission reduction in soil remediation.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60657-3
Fe-Mn catalysts have attracted considerable attention for industrial Fischer-Tropsch synthesis (FTS) due to their ability to modulate product spectra. Carbon adsorption and permeation on catalyst surfaces are critical elementary steps in the in situ formation of active iron carbide phases. Here, density functional theory (DFT) calculations systematically investigate the atomistic structures, thermodynamic stabilities, and electronic properties of carbon-deposited Fe-Mn alloy surfaces at the early stage of carburization. These surfaces exhibit distinct thermodynamic sensitivity to carbon atoms adsorbed on the surface and permeating into interstitial sites. By combining DFT with minima-hopping structural searches, we demonstrate that the initial stage of carbon permeation cannot trigger surface reconstruction to form iron carbide phases. The addition of manganese thermodynamically hinders carbon permeation. Although deposited carbon atoms modulate the electronic structure of metals, manganese retards the shift of d-band centers toward those of bulk iron carbide phases. This study provides atomic-scale insight into the in situ evolution of Fe-Mn catalyst surfaces during carbon deposition, indicating that manganese promoter has a noticeable effect on carbon permeation.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026030601
Bisphenol A (BPA), a high-volume industrial chemical, is implicated in neurotoxicity and chronic neurodegenerative diseases. This study integrates network toxicology, molecular docking, and molecular dynamics simulations to systematically delineate the common mechanisms linking BPA to Alzheimer's disease (AD), Parkinson's disease (PD), and Huntington's disease (HD). Using the human astrocyte cell line SVGP12 as an in vitro model, we identified six key toxic functional proteins—TP53, HSP90AA1, HSP90AB1, INS, BCL2, and AKT1—that mediate BPA's effects across these diseases, with BCL2 emerging as the most central node. Experimental validation demonstrated that BPA induces oxidative stress and cell cycle arrest, suppresses the INS-AKT1-BCL2 anti-apoptotic pathway, and activates the TP53-HSP90 pro-apoptotic pathway, culminating in mitochondrial apoptosis of astrocytes and disruption of neural microenvironment homeostasis. These findings reveal a convergent mechanism by which BPA accelerates neurodegeneration, filling a critical gap in understanding BPA's role in AD, PD, and HD. The study provides a novel theoretical framework and experimental evidence for BPA neurotoxicity risk assessment and informs preventive and therapeutic strategies for BPA-related neurodegenerative disorders.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025041405
Microplastics, as a class of emerging environmental contaminants, pose global concerns due to their potential ecological and human health impacts. Accurate identification and quantification of microplastics in environmental matrices are essential for assessing their environmental fate and ecological risks. Pyrolysis-based analytical methods, which decompose macromolecules into smaller fragments followed by gas chromatographic separation and mass spectrometric detection, offer high sensitivity and accuracy, making them significant for microplastic analysis. Despite these advantages, their application remains nascent, with limited comprehensive understanding of their applicability across diverse environmental media. This review systematically compares three pyrolysis-based techniques—pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS), thermogravimetry-differential scanning calorimetry (TGA-DSC), and thermal extraction-desorption gas chromatography-mass spectrometry (TED-GC-MS)—for microplastic detection in various matrices. The effectiveness of each method is evaluated in terms of sensitivity, selectivity, and matrix compatibility. Critical challenges, including lack of standardized protocols, complex sample pretreatment requirements, and limitations in quantifying mixtures, are identified. Future research directions emphasize the need for standardization, optimization of pretreatment for complex matrices, and integration with complementary techniques such as FTIR and Raman spectroscopy to enhance comprehensive microplastic characterization. This review provides a critical framework for selecting appropriate pyrolysis-based methods and highlights areas requiring further methodological development.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042702
This study estimated initial volume mixing ratios of volatile organic compounds (VOCs) in Dalian from June 1 to August 31, 2024, using a photochemical age-based parameterization method, and performed source apportionment with positive matrix factorization (PMF). Observed average TVOCs concentration was 12.49×10⁻⁹, comprising alkanes (84.2%), alkenes (10.4%), and aromatics (5.4%). Corrected initial TVOCs was 14.93×10⁻⁹, indicating a loss rate of 16.4%. Loss rates were highest for alkenes (53.2%), followed by aromatics (23.3%) and alkanes (6.8%). Ozone formation potential (OFP) averaged 21.31×10⁻⁹ (observed) and 38.75×10⁻⁹ (initial), with an OFP loss rate of 45.0%, distributed as alkenes (56.4%), aromatics (32.7%), and alkanes (10.3%). During ozone pollution episodes, TVOCs chemical loss was 1.9 times that of non-pollution periods, with alkene loss reaching 61.6%; OFP loss was 1.2 times higher, with alkenes contributing 88.4% to TVOCs loss. Secondary organic aerosol (SOA) formation potential from 08:00–17:00 was 1.51×10⁻¹ μg·m⁻³, with 99.4% from aromatics and toluene contributing 68.3%. PMF identified five sources: motor vehicles (49.6%), oil and gas volatilization (20.7%), petrochemical enterprises (12.6%), industrial processes (11.2%), and solvent use (5.9%). OFP modeling indicated motor vehicles contributed most to ozone formation (41.1%), followed by petrochemical enterprises (35.8%). During ozone pollution, PMF based on initial concentrations showed petrochemical sources had the highest OFP contribution (42.5%), whereas observed concentrations indicated motor vehicles as the top contributor (42.5%). This discrepancy underscores the necessity of correcting for photochemical losses in source apportionment studies.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608025
To evaluate heavy metal contamination and human health risks in desert lakes, this study analyzed concentrations of seven heavy metals (Hg, Pb, Cu, Zn, Cd, Cr, As) in Hongjiannao Lake, Northern Shaanxi, from 2013 to 2024. The absolute principal component score-multiple linear regression (APCS-MLR) model quantitatively apportioned pollution sources, and a health risk assessment model evaluated non-carcinogenic and carcinogenic risks. Results showed average concentrations of the seven metals did not exceed background values, but 28.57% of sampling points exceeded background for As, with a maximum exceedance factor of 1.92. Total average concentration decreased from 112.51 μg/L (2013–2016) to 58.80 μg/L (2017–2024), attributed to the 2016 closure of small coal mines and ecological restoration around the 4A scenic area. Source apportionment identified four sources: industrial (35.44%), agricultural (24.67%), natural (23.65%), and traffic (16.23%), indicating industrial dominance. Non-carcinogenic risks were negligible, but carcinogenic risks exceeded the alert value (1×10⁻⁴), with adults at higher risk than children. Oral ingestion was the primary exposure pathway. As and Cd were key control elements, with exceedance rates of 100% and 16.67%, respectively. These findings provide a theoretical basis for health risk prevention and environmental management.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4075-1
Titanium alloys, such as Ti-6Al-4V (TC4), are indispensable in aerospace, biomedical, and advanced manufacturing due to their high specific strength, corrosion resistance, and biocompatibility. However, their inherent strength-ductility trade-off and limited stiffness hinder next-generation lightweight structural applications. Traditional ceramic reinforcements (TiC, TiB2, SiC) improve strength but introduce brittleness and interfacial incompatibility, degrading plasticity and fatigue resistance. Graphene, with theoretical strength ~130 GPa and Young's modulus ~1 TPa, offers a promising two-dimensional reinforcement. This review systematically examines graphene-reinforced titanium matrix composites (TMCs), focusing on the intrinsic relationship between preparation, microstructure, and properties. Key preparation routes include powder metallurgy and additive manufacturing, with challenges in achieving uniform dispersion and controlling interfacial reactions. Recent studies demonstrate that surface modification and process optimization can form an ideal interface structure comprising a nano-TiC layer and residual graphene. Even at low graphene additions, synergistic strengthening mechanisms—load transfer, fine-grain strengthening, and Orowan dislocation bypass—significantly enhance strength, hardness, and wear resistance while preserving ductility. This review consolidates critical theoretical and experimental findings, offering guidance to overcome technological bottlenecks and promote engineering applications of graphene-reinforced TMCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4017-y
Lattice distortion via entropy engineering can significantly optimize thermoelectric performance by intensifying phonon scattering. However, excessive lattice distortion in high-entropy materials inevitably hinders carrier transport, limiting the wide-temperature average ZT (ZTave). To enhance the wide-temperature thermoelectric performance of low-cost PbS-based compounds, this work introduces moderate lattice distortion by controlling entropy around 1.0R (R is the gas constant) to balance phonon and carrier transport, alleviating restrictions on carrier mobility. Substantial Se and Te alloying in PbS induces rock-salt lattice distortion, effectively impeding phonon propagation, thus suppressing lattice thermal conductivity (κlat) from 2.41 W m−1 K−1 in PbS to 0.66 W m−1 K−1 in PbS0.5Se0.35Te0.15 at 300 K. Additionally, Cu interstitials are introduced into the lattice-distorted PbS0.5Se0.35Te0.15 to further optimize carrier density and weighted carrier mobility (μW), leading to significant improvement in μW/κlat parameter at 300–773 K. Finally, a room-temperature ZT of 0.53 and a maximum ZT of 1.44 are obtained in PbS0.5Se0.35Te0.15-1%Cu sample, contributing to an impressive ZTave of 1.08 at 300–773 K and a maximum power generation efficiency (ηmax) of 7.5%. The results outperform previously reported cost-effective PbS-based compounds and highlight the importance of lattice distortion regulation in enhancing wide-temperature thermoelectric performance.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3580-0
Hydrogel-based one-dimensional fibers offer a route to smart textiles, yet cyclic deformation fractures low-energy amorphous crosslinks, causing fatigue and hysteresis that degrade mechanical performance. This study integrates an Ecoflex elastomer backbone into an organic hydrogel to fabricate composite fibers (OHEF) with enhanced fatigue resistance and eliminated hysteresis. After 10,000 cycles at 200% strain, mechanical properties show no significant degradation. The strain sensor exhibits a gauge factor of ~3.0, response time of 140 ms, recovery time of 130 ms, and repeatability over 10,000 cycles at 70% strain. The OHEF also resists dehydration and freezing, enabling smart textiles that detect deformation, temperature, proximity, and pressure, and perform passive sensing via triboelectric nanogenerator principles. These results demonstrate a viable path for durable, multi-sensing hydrogel fibers in wearable electronics.