SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4499-9
Two-dimensional (2D) ferroelectric materials have emerged as promising candidates for next-generation non-volatile memory and neuromorphic computing, yet their integration into commercial devices faces substantial hurdles. This review critically examines the structure, properties, and applications of ferroelectric 2D In-Se materials, with a focus on their potential to overcome the scaling and retention limitations of conventional ferroelectrics such as Hf0.5Zr0.5O2 (HZO). The manuscript synthesizes recent advances in In-Se ferroelectricity, including the mechanisms of polarization switching, modulation strategies, and device demonstrations. Key experimental benchmarks from the literature are analyzed, such as the high data retention and read endurance of 5-nm HZO ferroelectric FETs (IEEE Electron Device Lett, 2019, 40(3): 399-402) and the giant barrier height modulation in ferroelectric van der Waals heterojunctions (Nat Electron, 2020, 3: 466-472). The review also highlights the performance of sliding ferroelectric memories based on rhombohedral-stacked bilayer MoS2, which achieved non-volatile storage with low power consumption (Nat Commun, 2024, 15: 10796). Despite these advances, critical challenges remain: the scalability of In-Se synthesis, the control of domain dynamics at the nanoscale, and the cost parity with silicon-based technologies. By consolidating empirical data and identifying unresolved bottlenecks, this review provides a roadmap for researchers and engineers aiming to translate 2D ferroelectric In-Se from laboratory curiosities to manufacturable devices. The analysis underscores the need for standardized metrology and accelerated lifetime testing to validate industrial viability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4494-9
Superionic conductors exhibit high cation mobility arising from weak binding and continuous transport pathways, atomistically characterized by extensive structural disorder and partial occupancy akin to amorphization. This disorder, whether confined to a cation sublattice or extended to full amorphization, strongly impedes lattice thermal transport, rendering these materials intrinsically ideal thermal insulators. This work investigates Ag26I18W4O16, a superionic conductor tunable from fully amorphous to single-crystalline states, as a model system to probe the impact of disorder and amorphization on thermal transport. Extensive Ag+ disorder, in both crystalline and amorphous phases, reduces thermal conductivity to approximately the theoretical lower bound of 0.16 W/m-K with virtually no temperature dependence, while concurrently achieving the lowest mean sound velocity ever recorded for a dense solid. Pair distribution function (PDF) analysis of synchrotron X-ray total scattering data indicates that short-range disorder (< 5 Å), rather than long-range periodicity, governs thermal insulation performance in both phases. These findings suggest a design strategy reconciling structural stability with glass-like thermal insulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4277-1
Two-dimensional (2D) magnetic materials hold promise for next-generation spintronics, yet most exhibit Curie temperatures (Tc) far below room temperature, limiting practical applications. Here, we report the realization of room-temperature ferromagnetism in CuCrSe2 nanosheets via controlled anion removal achieved by post-synthetic vacuum annealing. Raw CuCrSe2 shows a low Tc of ~120 K, whereas annealed CuCrSe2 (A-CuCrSe2) nanosheets exhibit robust ferromagnetic ordering above 300 K. Structural and compositional analyses, including transmission electron microscopy, Raman spectroscopy, and X-ray absorption spectroscopy, confirm that A-CuCrSe2 retains the original layered crystal structure with an estimated Se vacancy concentration of approximately 10%. Magnetic measurements reveal room-temperature ferromagnetism in exfoliated nanosheets, corroborated by magnetic imaging and electric transport measurements. Anomalous Hall effect (AHE) measurements uncover the coexistence of two ferromagnetic phases within the same sample: one with low Tc (~120 K) and another with high Tc (>300 K), indicating spatially heterogeneous magnetic ordering driven by anion removal distribution. Density functional theory (DFT) calculations elucidate the microscopic mechanism, suggesting that Se vacancies modulate the magnetic exchange interactions, enhancing Tc. This work demonstrates that anion modulation is an effective intrinsic strategy to achieve room-temperature ferromagnetism in 2D materials, potentially advancing spintronic applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3558-4
The development of advanced titanium alloys capable of operating above 600 °C remains a critical challenge for aerospace propulsion systems, where conventional Ti alloys suffer from insufficient high-temperature strength and microstructural instability. Here, we propose a computationally driven design strategy for titanium-based medium-entropy alloys (MEAs) that integrates thermodynamic phase prediction with mechanistically informed strength modeling, enabling systematic exploration of the Ti-Nb-Al-Cr quaternary system. The optimized Ti70Nb10Al15Cr5 MEA exhibits exceptional performance metrics: 18% room-temperature ductility (as-cast), a yield strength of 520.7 MPa at 650 °C (post-aging), and an ultralow density of 4.76 g/cm3 (45% lighter than Inconel 718). Microstructural characterization reveals a metastable single-phase BCC structure in the as-cast state, which transforms into a BCC/Ti3Al dual-phase system upon aging, with temperature-dependent precipitate morphology and phase stability. The alloy demonstrates superior high-temperature strength retention up to 900 °C (>80 MPa yield strength), outperforming commercial titanium alloys (e.g., Ti-1100, TG6) and bridging the performance gap between conventional Ti alloys and nickel-based superalloys. This work establishes a multi-criteria design paradigm for entropy-engineered alloys, offering a viable pathway to lightweight, high-temperature structural materials for next-generation aerospace applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3777-0
Optically clear adhesives (OCAs) are critical for next-generation optoelectronic systems, yet their end-of-life management remains a sustainability challenge. Here, we report a debondable and robust polyurethane (PU)-based OCA that integrates both mechanical and chemical recyclability. The PU-based OCA exhibits high optical transparency (>90% transmittance from visible to near-infrared), strong adhesion to glass and polymeric substrates (bonding strength up to 5.0 MPa), and thermally sensitive H-bonding interactions that enable on-demand deadhesion at elevated temperatures. This capability facilitates non-destructive detachment of functional assemblies, promoting component reuse and material recycling. The adhesive demonstrates excellent mechanical properties, including ductility and strength, and outperforms several commercial optical adhesives in key performance metrics. Its straightforward synthesis and industrial scalability make it a promising solution for advancing circular economy principles in optoelectronic device manufacturing. The work addresses critical bottlenecks in balancing mechanical performance, adhesion/detachment, and recyclability, offering a transformative approach to sustainable advanced manufacturing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3716-x
Flexible pressure sensors (FPSs) are pivotal for fall detection and rehabilitation training, yet conventional synthetic-based sensors suffer from resource-intensive manufacturing, high costs, and environmental pollution. This study introduces a sustainable fabrication strategy for FPSs using natural materials. Electrodes were fabricated by treating natural wood strips with a flame retardant, converting them into high-quality graphene via cost-effective infrared laser processing, and transferring onto starch-based substrates. The dielectric layer comprised an electrospun composite nanofiber membrane of cyclodextrin and carbon nanotubes. The resultant capacitive FPS exhibited high sensitivity (2.15 kPa⁻¹ within 0–10 kPa), a low detection limit (~6.5 Pa), rapid response and recovery times (29 ms and 39 ms), and excellent long-term stability exceeding 5000 cycles. Biocompatibility was outstanding (cell viability >98%), and the sensor fully degraded within 6 hours. Integrated with wireless technology, the sensor enabled a fall detection and rehabilitation monitoring system. Data processing utilized a Tiny Machine Learning module on a mobile platform, transmitting data to a cloud-based system. The system accurately identified five common fall postures and assisted clinicians in guiding rehabilitation exercises, achieving recognition accuracies of 99% and 100%, respectively. This work offers a sustainable healthcare solution for elderly care, addressing environmental and economic limitations of existing FPS technologies.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012101
Continuous monitoring of 114 volatile organic compounds (VOCs) was conducted in the urban atmosphere of Haigang District, Qinhuangdao City, from September 2022 to February 2023. The volume concentrations of total VOCs were 42.72×10⁻⁹ in autumn and 25.15×10⁻⁹ in winter. The predominant species were isopentane, ethane, and ethylene. Ozone formation potential (OFP) analysis indicated that alkanes and alkenes dominated the atmospheric pollution during autumn and winter, with isopentane and ethylene being the largest contributors. Aromatic hydrocarbons contributed up to 85.00% of the secondary organic aerosol formation potential (SOAFP), with benzene as the primary species. Positive matrix factorization (PMF) identified four major sources: technological processes and oil/gas volatilization (35.57%), combustion and petrochemical emissions, motor vehicle emissions, and regional background sources. The results underscore the need for targeted control of VOCs from industrial and vehicular sources to mitigate secondary pollution in coastal cities.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605019
The utilization of food waste as a fermentation substrate can effectively reduce the substrate cost of lactic acid production industrialization, and synergistic fermentation with leachate could promote lactic acid production. However, the effect of magnesium ions in leachate on lactic acid production, metabolic processes, and key functional bacterial communities remains unclear. This study investigated the effect of adding magnesium ions on lactic acid fermentation using food waste as substrate. Results showed that the optimal magnesium ion dosage was 750 mg/L, achieving a lactic acid yield of (37.4±0.5) g COD/L and L-lactic acid optical activity of (96.3±0.9)%. Mechanistic studies revealed that magnesium ions accelerated substrate dissolution, significantly enhanced the activities of key hydrolytic enzymes (α-glucosidase, amylase, protease) and L-lactic acid producing enzymes, thereby increasing hydrolysis and lactate production rates. Simultaneously, the relative activity of lactate-consuming enzymes decreased, slowing lactate consumption. At 750 mg/L Mg2+, the relative abundances of Enterococcus and Streptococcus were 65.0% (2.2 times the Blank) and 18.7% (37.8% of the Blank), respectively, with a total of 83.7%, enhancing lactic acid yield and L-lactic acid optical activity. Metabolic pathway prediction and functional gene analysis further indicated that magnesium ions increased the relative abundance of carbohydrate metabolism pathways and genes encoding lactate dehydrogenase. This study provides technical support for food waste resource utilization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3809-y
The development of hydrogels that simultaneously achieve high strength and good toughness remains a critical challenge in soft material science, particularly for applications in flexible electronics, soft robotics, and biomedical devices. Conventional approaches often suffer from a trade-off between mechanical robustness and functional performance. In this work, we present a novel solvent-driven dual-network entanglement strategy to fabricate a strong and tough poly(vinyl alcohol) (PVA)-based organo-hydrogel by synergistically combining isopropanol (IPA) solvent substitution to induce dense polymer chain entanglement and a sodium alginate (SA) ionic crosslinked network as a dynamic energy-dissipation phase. The resulting organo-hydrogel exhibits excellent mechanical performance with a tensile strength of 3.18 MPa and a toughness of 16.65 MJ/m3, representing increases of approximately 17 and 49 times that of conventional PVA hydrogels, respectively. Furthermore, the organo-hydrogel displays superior swelling resistance and long-term stability in aqueous environments, enabling reliable operation in challenging conditions such as underwater motion sensing and wearable strain detection. Morphological analyses reveal the critical role of solvent-mediated chain reorganization and dual-network interactions in achieving these properties. This work not only provides a versatile platform for designing robust gel materials but also offers fundamental insights into solvent-network interactions for advanced soft material engineering.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3949-4
Sodium metal is considered an ideal anode material for high-performance sodium-based batteries. However, volume changes and dendrite growth during cycling seriously restrict its practical application. To address these challenges, this study utilizes harmful green tide algae Enteromorpha prolifera as a raw material to fabricate a self-supporting, sodiophilic, 3D Enteromorpha prolifera-derived carbon (EC) matrix via defect engineering. The results demonstrate that the 3D EC matrix can reduce nucleation overpotential, enhance binding ability with sodium atoms, and induce sodium to deposit horizontally inside EC, effectively addressing the issue of dendrite formation. Furthermore, the Na-EC symmetric cell demonstrates exceptional cycling stability with an ultralow polarization of 12 mV over 1000 h at 5 mA cm−2, 5 mA h cm−2. Notably, this stability persists even under ultrahigh current density and areal capacity conditions (30 mA cm−2, 30 mA h cm−2), maintaining stable operation for 500 h. When configured in full-cell systems with Na3V2(PO4)3 cathode, the assembled cell delivers an initial discharge capacity of 108.1 mA h g−1 at a 1 C rate, and maintains a capacity retention rate of 94.4% after 500 cycles. This study proposes an innovative strategy to advance high-performance dendrite-free sodium metal batteries through the recycling of marine environmental waste into functional energy materials.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512015
The co-contamination of cadmium (Cd), lead (Pb), and zinc (Zn) in agricultural soils near mining areas poses significant risks to ecosystems and human health. Conventional stabilization materials often exhibit insufficient performance for Zn, particularly in multi-metal systems. This study synthesized a novel composite biochar (PFMBC) by loading phosphate and iron-manganese oxides onto biochar via phosphoric acid impregnation followed by secondary pyrolysis at 600 °C. The stabilization efficiency of PFMBC was evaluated against pristine biochar (BC) and iron-manganese modified biochar (FMBC) in a soil collected from a lead-zinc mining area (total Cd: 43.77 mg·kg−1, Pb: 3355.94 mg·kg−1, Zn: 1296.57 mg·kg−1). After 60 days of incubation with 5% PFMBC, the DTPA-extractable (bioavailable) fractions of Cd, Pb, and Zn decreased by 73.44%, 90.10%, and 69.33%, respectively, significantly outperforming BC and FMBC. Sequential extraction indicated that PFMBC promoted the transformation of Cd, Pb, and Zn from acid-soluble and reducible fractions to more stable residual fractions. Characterization via FTIR, SEM, and XRD revealed enhanced surface functional groups and the formation of stable mineral phases. The synergistic effects of phosphate precipitation, iron-manganese oxide adsorption, and surface complexation contributed to the superior stabilization, particularly overcoming the challenge of Zn immobilization. These findings demonstrate that PFMBC is a promising amendment for the remediation of Cd-Pb-Zn co-contaminated soils, offering high efficiency and long-term stability.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608024
Microbial remediation is a widely used technology for treating chromium pollution in groundwater. This study conducted a bibliometric analysis of 441 papers from the Web of Science Core Collection (2010–2024) using CiteSpace, VOSviewer, and Pajek. The publication trend increased over the period, with three developmental stages identified: early (2010–2016) focusing on basic treatment methods, intermediate (2017–2019) on intrinsic mechanisms, and recent (2020–2024) on process optimization. Biological adsorption and reduction were identified as the primary mechanisms. Correlation and principal component analyses of environmental factors (temperature, pH, initial Cr concentration, reaction time) revealed temperature as the key factor affecting remediation efficiency. The removal efficiencies and mechanisms of various dominant bacterial strains were summarized to guide strain selection. Future research should focus on microbial community synergy, nanomaterial integration, and environmental optimization to enhance remediation efficiency.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4057-4
The escalating use of ionizing radiation in medical and industrial applications necessitates lead-free, flexible, and sustainable shielding materials. Current development relies on empirical trial-and-error, which is inefficient. This study introduces a machine learning-assisted Monte Carlo simulation strategy for rapid optimization of metal filler compositions for X-ray attenuation across 40–120 kV. Guided by this AI-driven approach, polyvinyl alcohol (PVA)-based gels containing uniformly dispersed Bi/W/Gd2O3 nanoparticles were developed, forming within 1 minute at -20°C using a PVA-DMSO/H2O co-solvent system. The optimized gel with 50 wt% metal loading exhibits exceptional mechanical properties: tensile strength of 1.76 MPa, toughness of 6.3 MJ m−3, and elongation of 600%. It achieves >98% X-ray shielding efficiency at 5 mm thickness, outperforming lead composites at 120 kV. The physically cross-linked network provides recyclability and anti-freezing capability, retaining flexibility at -50°C. This work establishes a data-driven paradigm for designing high-performance radiation-shielding materials, demonstrating AI's potential to accelerate materials discovery and enable scalable fabrication of eco-friendly protective systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4109-2
The fabrication of high-efficiency organic solar cells (OSCs) under ambient conditions remains a formidable challenge due to the sensitivity of active layer morphology to environmental factors. We propose an innovative approach for air-processed devices that combines spontaneous water-spreading film formation with layer-by-layer (LBL) deposition. This method enables the fabrication of donor- and acceptor-dominant bulk heterojunction blend films near the anode and cathode interfacial layers, respectively, optimizing vertical phase separation and enhancing charge transfer efficiency. In the D18:L8-BO system, the device achieves a power conversion efficiency (PCE) of 19.02% with an exceptionally narrow efficiency distribution. Even for devices with an area of 1 cm2, a PCE of 16.56% is attained. After a 1000-hour decay test, the efficiency retains 84.1%. This novel method offers a promising pathway for advancing the industrial application of large-area, highly stable devices with narrow efficiency distribution under ambient conditions.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3643-8
Inverted perovskite solar cells (PSCs) suffer from defect-mediated nonradiative recombination and inefficient charge extraction, particularly at the buried interface and grain boundaries (GBs), which limit power conversion efficiency (PCE) and operational stability. This study introduces a multifunctional phosphonic acid molecule, (2-(3,6-bis(trifluoromethoxy)-9H-carbazol-9-yl)ethyl)phosphonic acid (M28), as an additive in the perovskite precursor solution. M28 spontaneously segregates toward the buried interface and GBs, fulfilling three roles: (1) slowing crystallization to enlarge grains and improve film quality, (2) passivating defects to suppress charge recombination, and (3) inducing p-type doping to create an extra electric field that promotes hole transport. Devices incorporating M28 achieve a champion PCE of 25.96% and retain 80% of initial efficiency after 1500 h of maximum power point tracking. This work demonstrates the efficacy of multifunctional phosphonic acid additives in addressing buried-interface and GB defects, offering a viable route to high-performance, stable inverted PSCs.