SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4472-0
Dynamic electrocardiography (ECG) monitoring during physical activity remains compromised by motion artifacts that corrupt signal fidelity, particularly with conventional gel electrodes whose impedance rises sharply under deformation. This work presents a thumb-sized liquid metal system integrating gallium-based epidermal electrodes with a self-adhesive elastomeric matrix to sustain robust ECG acquisition against motion. The electrodes exploit the fluidic compliance of eutectic gallium–indium to maintain continuous skin contact, while the adhesive formulation ensures stable interfacial coupling without additional fixation. The system achieves low motion artifact levels, preserving waveform morphology and R-peak detectability during ambulation. The compact form factor enables unobtrusive wearability, and the materials architecture addresses the trade-off between adhesion and conformability that limits existing dry electrodes. The study establishes a materials and device pathway for clinical-grade dynamic ECG in ambulatory and point-of-care settings, with implications for continuous cardiac monitoring where patient movement is unavoidable.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4371-6
The sluggish kinetics of the oxygen reduction reaction (ORR) necessitates platinum-based catalysts, but their high cost and scarcity drive the search for platinum-group metal-free (PGM-free) alternatives. Fe−N−C catalysts with atomically dispersed Fe−N4 sites are promising, yet their practical performance is limited by buried active sites and poor mass transport. Here, a crumpled, multi-scale porous Fe−N−C catalyst (Fe−N−PCG) is synthesized via spray pyrolysis coupled with high-temperature metal etching. The crumpled morphology, formed by capillary compression during rapid solvent evaporation, and in-plane mesopores from Fe nanoparticle etching, synergistically enhance site accessibility and mass transport. Fe−N−PCG achieves a site density (SD) of 2.74×10^19 sites g−1 and Fe utilization (UFe) of 51.7%. As a gas diffusion electrode, it delivers a mass transport overpotential (ηmt) of 67 mV at 800 mA cm−2. In zinc-air batteries, Fe−N−PCG exhibits a peak power density of 296.1 mW cm−2 at 500 mA cm−2, outperforming Pt/C (241 mW cm−2 at 438 mA cm−2). At 50 mA cm−2, it delivers a discharge voltage of 1.19 V and a specific capacity of 815 mAh g−1, surpassing Pt/C (1.13 V, 715 mAh g−1). These results demonstrate that morphology and porosity engineering can concurrently optimize intrinsic activity, site utilization, and mass transport, offering a rational design strategy for high-performance PGM-free catalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4383-8
Conventional cancer therapies remain constrained by undruggable oncogenic proteins and acquired resistance. Proteolysis targeting chimeras (PROTACs) have emerged as a transformative modality that harnesses the ubiquitin-proteasome system to selectively degrade target proteins, offering advantages over traditional small-molecule inhibitors. However, clinical translation of PROTACs is impeded by intrinsic physicochemical limitations: high molecular weight, poor bioavailability, and lack of tumor-specific delivery. Integrating PROTACs with nanotechnology has yielded advanced nano-PROTACs platforms. Nanocarriers enhance solubility and stability, optimize pharmacokinetics, and enable spatiotemporally controlled drug release through passive or active targeting. This review systematically summarizes recent advances in engineering multifunctional nano-PROTACs for cancer therapy, with particular emphasis on design strategies by which nanoengineering enhances PROTAC performance. We evaluate how these platforms improve anticancer efficacy and minimize systemic toxicity while exploring their therapeutic potential in monotherapy and synergistic treatment settings. Finally, we discuss current challenges and future perspectives, providing a theoretical and technical foundation for next-generation nano-PROTACs as a precise and potent strategy in precision oncology.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4412-y
GeTe-based thermoelectric materials are promising lead-free alternatives to PbTe, but their intrinsically high Ge vacancy concentration (~10^21 cm^-3) leads to excessive carrier density and degraded Seebeck coefficient. This study integrates resonant levels (RLs) via In doping and local van der Waals gaps via Sb/Bi alloying to decouple electron and phonon transport. The optimal composition Ge0.91Sb0.04Bi0.04In0.01Te exhibits a Seebeck coefficient of ~287.31 μV K^-1 at 323 K, more than double that of the In-free sample (~102.28 μV K^-1). The peak figure of merit zT reaches ~1.8 at 723 K, with an average zT of ~1.0 over 323–723 K. Vickers hardness is enhanced to ~224 HV, a ~93% improvement over pristine GeTe (~116 HV). X-ray diffraction reveals a structural evolution toward a pseudo-cubic phase with increasing In content, and the (202) peak shifts to lower angles, indicating lattice expansion. These results demonstrate that synergistic RLs and van der Waals gaps effectively optimize carrier concentration and suppress thermal conductivity, offering a viable route for high-performance, mechanically robust GeTe thermoelectrics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4238-2
Infrared nonlinear optical (IR NLO) materials are critical for laser frequency conversion, yet their performance is often constrained by a trade-off between second harmonic generation (SHG) efficiency and laser-induced damage threshold (LIDT). Here, we report a new ternary diamond-like compound, AlGaS3, which successfully balances these competing demands. AlGaS3 crystallizes in a noncentrosymmetric structure composed of wide HOMO-LUMO gap [AlS4] tetrahedra and NLO-active [GaS4] tetrahedra. The compound exhibits a wide experimental optical band gap of approximately 3.38 eV, which is significantly larger than that of the benchmark AgGaS2 (AGS, ~2.70 eV). This wide band gap contributes to a high laser-induced damage threshold (LIDT) of approximately 6.0 times that of AGS, as determined by powder-based measurements. Notably, AlGaS3 also demonstrates a phase-matching SHG response of approximately 0.5 times that of AGS at a fundamental wavelength of 2.09 μm, with particle size-dependent behavior confirming phase-matchability. The combination of wide band gap, high LIDT, and moderate SHG response positions AlGaS3 as a promising candidate for high-power IR NLO applications. This work provides a viable strategy for designing IR NLO materials with enhanced laser damage resistance by incorporating wide-gap tetrahedral units.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4269-4
Self-assembled molecular interlayers (SAMs) are promising hole-selective contacts for high-efficiency organic solar cells (OSCs) due to their well-defined energy alignment and minimal parasitic absorption. However, their intrinsically limited mechanical robustness often leads to structural degradation and performance loss under mechanical deformation, restricting their application in flexible devices. Here, we report a nanoparticle-reinforced self-assembled composite interface that simultaneously enhances mechanical reliability and optoelectronic performance. Uniformly dispersed SiO2 nanoparticles are introduced as high-modulus reinforcing building blocks without disturbing molecular self-assembly. In contrast to NiOx nanoparticles, which suffer from aggregation and parasitic absorption, SiO2 nanoparticles exhibit excellent dispersion and optical transparency, enabling formation of a structurally compatible hybrid interface. Mechanistic studies reveal that SiO2 nanoparticles redistribute interfacial stress and form dynamic hydrogen-bond networks with phosphonic acid groups of 2PACz, providing efficient energy dissipation during cyclic deformation. Meanwhile, modulation of interfacial polarity extends the crystallization time window of the active layer, resulting in enhanced molecular ordering and improved charge transport. As a result, devices based on the SiO2/2PACz composite interface achieve a power conversion efficiency of 20.14% for rigid devices and 19.30% for flexible devices, placing the flexible devices among the highest-performing flexible OSCs reported to date, while retaining over 90% of their initial efficiency after repeated bending cycles. This work establishes a general strategy for overcoming the trade-off between electronic selectivity and mechanical robustness in ultrathin self-assembled molecular interfaces, providing design insights for high-performance flexible organic optoelectronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4202-3
Carbon dots (CDs) with absorption in the second near-infrared window (NIR-II, 900-1700 nm) hold promise for tumor theranostics, yet existing synthesis methods often involve complex procedures, harsh conditions, or lack precise control. Here we report a 'self-photooxidation-restructuring' strategy that enables structural reorganization of the carbon core in CDs, achieving a significant redshift of absorption into the NIR-II region. Under ultraviolet (UV) light irradiation, the precursor (B-CDs, absorption in UV region) generates singlet oxygen, which self-oxidizes aldehyde groups and the carbon skeleton of B-CDs to stronger electron-withdrawing carboxyl groups and carbon radicals, respectively. These processes facilitate the formation of new C=C bonds between isolated aromatic domains, thereby transforming B-CDs into novel CDs (N-CDs) characterized by enhanced donor-acceptor interactions and a redshift in absorption toward the NIR-II window. Various experimental data, including high-resolution XPS, FTIR, NMR, EPR, have proved the proposed formation mechanism. The novel N-CDs afforded a high photothermal conversion efficiency of up to 71.33%, which enabled 1064 nm laser-activated photoacoustic imaging (PAI)-guided photothermal therapy (PTT) in tumors. This work opens a new avenue for the synthesis and modulation of CDs in the NIR-II region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4342-3
Electron acceptors containing single-bond-linked building blocks offer attractive advantages for organic solar cells owing to their synthetic simplicity and structural modularity. However, achieving backbone planarity without compromising electronic compatibility remains a persistent challenge. Conventional conformational locking strategies based on alkoxy substitution can effectively suppress torsional freedom but often elevate the highest occupied molecular orbital energy level, limiting compatibility with widely used donor polymers. Here, we report a partially fused electron acceptor design that achieves intrinsic backbone planarity through heterocycle selection rather than side-chain-assisted conformational locking. By incorporating a benzodifuran core and furan-thiophene linkages, the resulting acceptors exhibit a near-coplanar backbone geometry as revealed by density functional theory calculations, without the need for electronically perturbing alkoxy groups. Devices based on the optimized acceptor (BDF-1) deliver a binary power conversion efficiency of 12.2%, and further improvement to 19.5% is achieved in a ternary blend with PM6 and BTP-eC9. The enhanced performance is accompanied by favorable morphology, balanced charge transport, and suppressed recombination losses. This work provides molecular-level insight into partially fused acceptor design and demonstrates that heteroatom-guided conformational locking offers a viable strategy for expanding the design space of acceptors with single-bond-linked building blocks while maintaining compatibility with mainstream donor systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4369-1
Sodium-ion batteries (SIBs) are promising alternatives to lithium-ion batteries for large-scale energy storage due to sodium's abundance and low cost. Among cathode materials, polyanionic compounds like Na3V2(PO4)2O2F (NVPOF) offer high energy density and dual voltage plateaus at ~3.6 and 4.0 V, but suffer from low electronic conductivity and sluggish Na+ diffusion. Here, we report a dual-modulation strategy combining high-valence Nb5+ doping and polydopamine-derived carbon coating to synthesize Na3V1.94Nb0.06(PO4)2O2F-C (NVPOF-Nb-C) via a hydrothermal route. X-ray diffraction and Rietveld refinement confirm that Nb5+ doping induces slight lattice expansion without altering the tetragonal I4/mmm framework. Density functional theory calculations reveal that Nb5+ doping optimizes the crystal structure and reduces the Na+ diffusion barrier, while the uniform carbon coating enhances electron transport. Consequently, NVPOF-Nb-C exhibits remarkably improved electrochemical performance, including high reversible capacity, excellent rate capability, and ultralong cycling stability. In a full cell with hard carbon anode, it delivers a high energy density of 487.2 Wh kg−1 at 1C and retains 91.51% capacity after 3000 cycles at 20C. This work provides a synergistic strategy to overcome the intrinsic limitations of polyanionic cathodes for practical SIB applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4176-y
Three-photon microscopy (3PM) in the near-infrared-III (NIR-III) window (1600–1840 nm) enables high-resolution visualization of cerebral vasculature in vivo, but its imaging depth and quality are limited by the performance of fluorescent probes. Here, we report a probe optimization strategy transitioning from mirror symmetry to centrosymmetry, yielding a highly symmetric aggregation-induced emission (AIE) molecule, T4PQ. The centrosymmetric structure aligns donor-acceptor units, promoting uniform electron cloud delocalization and directional charge transfer, which enhances exciton formation and suppresses non-radiative decay, thereby increasing fluorescence quantum yield. This symmetry also boosts the three-photon absorption cross-section by enhancing electron delocalization and transition dipole moment, enabling stronger nonlinear optical responses under long-wavelength excitation. T4PQ nanoparticles (T4PQ NPs) exhibit an enhanced three-photon absorption cross-section, high fluorescence quantum yield, and excellent photostability. In murine models, T4PQ NPs achieved three-dimensional cerebrovascular imaging at a depth of 1785 μm and real-time hemodynamic observation in microvessels at 1006 μm depth, with good biocompatibility. These results validate the advantage of centrosymmetric molecular design for deep-brain imaging probes, offering a high-performance tool for neurovascular research.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4112-6
Radiostrontium remediation is crucial for ecological protection and sustainable development of nuclear energy. However, efficient removal of 90Sr from complex radioactive liquid waste, especially under acidic conditions, remains challenging due to material instability and intense proton competition. Herein, the rapid and highly selective capture of Sr2+ in neutral and even acidic solutions has been achieved by a layered potassium phosphatoantimonate KSbP2O8 with excellent radiation and thermal stability. Under neutral conditions, it possesses high maximum adsorption capacity (qmSr = 110.25 mg g−1), rapid adsorption kinetics (the removal rate (RSr) of 91.54% within 30 min), and excellent selectivity for Sr2+, and facile regeneration. Particularly, even under acidic conditions (pH 2.0), KSbP2O8 still maintains excellent Sr2+ removal capacity (qmSr = 79.38 mg g−1), fast kinetics, and high selectivity. A mechanism study by multiple characterizations reveals that the efficient Sr2+ removal of KSbP2O8 mainly stems from ion exchange between Sr2+ and interlayer K+ in KSbP2O8, which is attributed to the synergy between the Sb5+-induced Brønsted acidity and the high charge density of the anionic framework. This study demonstrates the exceptional capability of phosphatoantimonates to selectively capture Sr2+ under acidic conditions, highlighting the potential of phosphatoantimonates as effective scavengers for radiostrontium remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4153-2
Direct seawater electrolysis offers a promising route to green hydrogen production, circumventing freshwater scarcity. However, the presence of chloride ions (Cl−) poses severe challenges, including competing chlorine evolution reaction (CER) and corrosion of anode catalysts. Here, we report a dual-atom catalyst design, RuCr-Ni3P, where Ru atoms with strong chloride affinity and Cr atoms as Lewis acid centers are co-doped into a nickel phosphide matrix. This catalyst exhibits outstanding oxygen evolution reaction (OER) activity and selectivity in alkaline seawater, achieving stable operation for over 4000 hours at industrially relevant current densities. Mechanistic studies reveal that Cl− ions are selectively captured by Ru sites, forming a dynamic Ru–Cl coordination motif that electronically modulates adjacent Ni centers, promoting the formation of high-valent Ni>3+ species. This switches the OER pathway from the lattice oxygen mechanism (LOM) to the more efficient adsorbate evolution mechanism (AEM). Concurrently, Cr sites facilitate the formation of Cr–OH species, creating a localized alkaline microenvironment that further enhances OER kinetics. This dual-site synergistic mechanism transforms Cl− from a detrimental impurity into a beneficial chemical switch, concurrently enhancing both activity and stability. Our findings provide a paradigm shift in seawater electrolysis catalyst design, turning a longstanding challenge into an opportunity for efficient and durable hydrogen production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3564-9
Sluggish water dissociation kinetics in the alkaline hydrogen evolution reaction (HER) hamper its practical production. Here, a heterojunction electrocatalyst featuring Ru-Ni(OH)2 interfaces on nickel foam (NF) with self-engineered built-in electric fields (BIEF) was synthesized via a simple in situ galvanic replacement reaction. The hierarchical Ru-Ni(OH)2/NF exhibits a record overpotential of 9.6 mV at 10 mA cm−2 for alkaline HER, surpassing most reported catalysts and commercial Pt/C. It also shows exceptional activity for hydrazine oxidation reaction (HzOR) at 100 mA cm−2 with a remarkably low potential of ca. 0.015 V vs. RHE. The assembled overall hydrazine splitting (OHzS) system integrating HER and HzOR requires a cell voltage of about 0.09 V to reach 50 mA cm−2, which is 1.637 V lower than the corresponding overall water splitting (OWS) device. Systematic analysis and calculation reveal that the BIEF induces redistribution of interfacial electrons for Ru, facilitating H2O dissociation and intermediate conversion, delivering ultra-high electrocatalytic performance. This work provides an avenue for design and preparation of electric field-mediated catalysts towards sustainable energy conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3645-3
Postoperative abdominal adhesion, a complication with morbidity exceeding 90%, imposes severe clinical and economic burdens. Existing bioadhesive barriers often exhibit unreliable adhesion to the slippery abdominal wall, risk mispositioning, and neglect frictional stimuli and inflammation. Inspired by the lubricated peritoneum, we developed a programmable adhesive dual-layer Janus patch (DJP) barrier integrating a lubricated layer and an adhesive matrix. DJP achieves rapid, noncovalent interfacial adhesion, subsequently enhanced 2.81-fold via covalent interactions, enabling repositioning within a short time window to improve surgical fault tolerance. The micron-scale poly(sulfobetaine methacrylamide) brush on the DJP surface provides hydration lubrication with a low coefficient of friction (0.06), mimicking peritoneal lubrication and reducing frictional damage to injured tissue. The catechol-containing copolymer confers antioxidative and anti-inflammatory properties, confirmed in vitro. In a rat model, DJP adhering to the injured site significantly reduced collagen deposition between the abdominal wall and cecum, preventing adhesion and promoting tissue healing compared to commercial barriers. This work provides a guiding reference for developing antiadhesive biomaterials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3746-x
The polyanionic compound Na3V2(PO4)2O2F (NVPOF) possesses a stable three-dimensional framework, high theoretical specific capacity, and favorable operating voltage, yet its sluggish Na+ diffusion kinetics and low electronic conductivity impede industrial application. This study proposes a dual regulation strategy combining carbon coating and heat treatment temperature to synergistically enhance crystallinity and electrochemical performance. NVPOF@C-400 and NVPOF@C-600 were synthesized via in-situ dopamine hydrochloride coating followed by heat treatment at 400 °C and 600 °C, respectively. Carbon coating at 600 °C significantly improved crystallinity and increased electronic conductivity by three orders of magnitude through the carbon layer's conductive network. The ~4.5 nm carbon layer effectively suppressed abnormal grain growth and secondary crystallization aggregation at high temperatures, maintaining uniform particle size of approximately 0.36 μm, which shortens Na+ diffusion pathways and prevents ion transport obstruction. Consequently, NVPOF@C-600 delivered a high discharge capacity of 102.5 mAh g−1 at 20 C and retained 96.5% capacity after 10,000 cycles. In a full-cell configuration with hard carbon (HC), NVPOF@C-600//HC achieved an impressive 89.3% capacity retention after 9,000 cycles. This work provides critical insights for practical implementation of high-performance NVPOF cathodes in sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3815-0
The development of bifunctional electrocatalysts capable of integrating biomass-derived platform molecule oxidation with organic reduction offers a promising strategy for simultaneously enhancing energy efficiency and generating high-value chemicals. However, designing catalysts that exhibit both high activity and stability in integrated systems remains a significant challenge. Herein, we report a self-supported electrode composed of nitrogen-doped carbonized wood (NCW) supported NiCo nanosheets (NiCo 0.3/NCW) that enables the electrocatalytic 5-hydroxymethylfurfural oxidation to produce 2,5-furandicarboxylic acid (FDCA) and the nitrobenzene reduction to yield aniline in an integrated electrochemical cell. The NiCo 0.3/NCW electrode achieves the production of FDCA and aniline at a low cell voltage of 1.7 V, with ~99% anodic and ~92% cathodic Faradaic efficiencies, respectively. Experimental characterizations disclose that the hierarchical porous NCW architecture promotes the dispersion of active sites, while nitrogen doping strengthens metal–support interactions. In-situ spectroscopic experiments combined with density functional theory (DFT) calculations reveal that cobalt incorporation tunes the electronic structure of nickel, thus optimizing substrate and intermediate adsorption, and lowering energy barriers. These effects ultimately enhance the performance of the natural wood-derived catalyst in integrated biomass valorization and selective organic electrosynthesis.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507032
To mitigate global warming, regional carbon neutrality pathways are critical. Based on the Guangdong Energy Policy Simulator (EPS) model, this study simulates total energy consumption and greenhouse gas (GHG) emissions under baseline, Carbon Neutral 60 (CN60), and Carbon Neutral 50 (CN50) scenarios, and analyzes the emission reduction effects and costs of various energy policies. Results show that by 2060, total energy consumption under CN60 and CN50 decreases by 39% and 44% relative to baseline, respectively. Primary electricity and other energy, natural gas, oil, and coal account for 56%, 26%, 14%, and 4% under CN60, and 60%, 24%, 13%, and 3% under CN50. GHG emissions under CN60 drop to 80×10^6 tCO2e by 2060, an 89% reduction from 2020; under CN50, emissions reach 92 and 55×10^6 tCO2e in 2050 and 2060, respectively, reductions of 87% and 92% from 2020. Policies such as increasing clean electricity share, industrial electrification (hydrogen), increasing green power purchases, building electrification, F-gas reduction, and improving industrial energy efficiency standards show significant reduction effects, with clean electricity share being the primary source. Policies like improving industrial energy efficiency standards, increasing industrial product utilization, and increasing clean energy vehicle market penetration are cost-effective; increasing clean electricity share, green power purchases, building electrification, and F-gas reduction effectively balance reduction effects and costs. Industrial electrification (hydrogen) contributes >5% cumulative reduction but faces economic challenges for full-scale promotion in the short term; industrial carbon capture and storage and electrolytic hydrogen contribute <2% cumulative reduction with high costs. Therefore, Guangdong should prioritize cost-effective policies, promote balanced policies, gradually optimize energy structure, achieve clean electricity, and foster green industrial transformation to achieve carbon neutrality at lower economic cost.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024110202
Anaerobic digestion (AD) is an environmentally friendly biochemical technology for waste treatment and renewable energy production, yet its methane conversion efficiency remains suboptimal. This study employed flux balance analysis (FBA) to determine the optimal temperature for methane production in AD, and subsequently regulated key flexible nodes in the metabolic pathway to maximize methane flux. At the optimal temperature of 40 °C, up-regulating the acetyl-CoA flexible node increased methane flux by 48.5%, while up-regulating the acetate node increased it by 36.6%. The higher improvement via acetyl-CoA regulation is attributed to the fact that 40 °C is unfavorable for hydrogen-producing acetogenic bacteria, making acetyl-CoA the critical control point. These findings demonstrate that flexible node regulation can overcome the limitations of temperature optimization alone. The FBA methodology provides a reliable, cost-effective approach for optimizing target product yields in AD and other fermentation systems, requiring only input and output measurements to resolve intermediate metabolic fluxes.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604001
This study systematically investigated the occurrence, spatial distribution, sources, and ecological risks of 160 pesticides in Dianchi Lake, a typical plateau lake impacted by agricultural activities. A total of 37 pesticides were detected in the water, with total concentrations ranging from 64.2 to 1132.8 ng/L (average 610.0 ng/L). Fungicides, including boscalid (BOS), fluopicolide (FPC), and dimethomorph (DMM), were dominant, contributing up to 65.0% of the total concentration. Spatially, the southern lake region exhibited significantly higher concentrations (672.5 ng/L) than the north, attributed to intensive facility agriculture. Highly hydrophobic pesticides, such as penconazole (PEN), showed a tendency to enrich in bottom layers. Source apportionment identified inflowing rivers and wastewater treatment plant effluents as primary input sources, with average concentrations 7 and 9 times higher than lake water, respectively. Ecological risk assessment revealed that pesticides posed the highest risk to algae, followed by daphnia and fish. Prometryn (PMT) was identified as a high-risk factor for algae, while profenofos (PFF) and carbendazim (CBD) posed potential threats to higher trophic levels. These findings provide fundamental data and technical support for understanding pesticide pollution in plateau lake ecosystems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3451-2
Visual aesthetics is a key metric of semi-transparent organic photovoltaics (ST-OPVs) for building-integrated solar windows, yet previous studies have primarily focused on the compromise between efficiency and transparency. This work addresses the overlooked aspect of full visual aesthetic control, particularly the bidirectional reflected color for architectural harmony, via designing ST-OPVs with double-sided ultra-thin Ag/TeO2 transparent electrodes. This design facilitates full-spectrum color tunability covering the whole standard color gamut of CIE coordinates on both surfaces, achieved simply by adjusting layer thicknesses. The resulting devices exhibit neutral transparency (16.6%–27.0% average visible transmittance) and competitive power conversion efficiencies (8.1%–9.2%). Additionally, the devices demonstrate strong flexibility, with flexibility-adaptive coloration and curvature-enhanced aesthetics. This work presents an ST-OPV design featuring full visual aesthetics and considerable performance, paving the way for commercialization of organic solar windows for building and vehicle integration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3782-0
Oral mucositis (OM) is a debilitating complication of cancer therapy, characterized by severe pain, mucosal barrier breakdown, and infection risk. Current hydrogel-based topical systems suffer from poor transmucosal permeation and lack of inflammatory microenvironment-triggered drug release. Here, we report a supramolecular strategy for designing guanosine-fibril hydrogels and derived microneedle patches. Tavaborole (Ta), crisaborole (Cr), and strontium (Sr2+) ions serve dual roles as structural building blocks and biofunctional agents. Unlike conventional G4·K+ fibrils, the unique G4·Sr2+-Ta/Cr fibrils incorporate Ta/Cr via boronic ester bonds on guanosine and Sr2+ through G-quartet cation recognition. This design mechanically reinforces the hydrogel through additional hydrophobic interactions and ion-pair recognition, while synergistically providing antimicrobial/anti-inflammatory effects (Ta/Cr), pro-angiogenic activity (Sr2+), and reactive oxygen species (ROS) scavenging (guanosine). The optimized gelation process enables fabrication of microneedle patches with pseudomembrane-penetrating capability and ROS-triggered drug release via boronic ester hydrolysis. In vivo mouse experiments confirm efficacy in controlling OM-associated inflammation, modulating oral microbiota homeostasis, and promoting angiogenesis at ulcer sites. This work demonstrates multifunctional integration via hierarchical structural design, extending guanosine supramolecular assemblies into bioactive platforms for OM treatment.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507094
To address land waste and poor bearing capacity from sludge landfill, this study developed a composite solidifying agent using loess, fly ash, desulfurized gypsum, and cement. Orthogonal experiments combined strength testing, SEM/XRD microanalysis, permeability and heavy metal leaching tests, and cost accounting. Results show that cement significantly enhances early and mid-term strength, while loess dominates later strength development. Optimal fly ash and desulfurized gypsum content is 12% each. The optimal mix ratio (loess:fly ash:desulfurized gypsum:cement:sludge) is 0.1:0.12:0.12:0.08:1. The solidified matrix forms dense structures via C-S-H gel and ettringite (Aft), effectively controlling heavy metal leaching at low cost. This work enables solid waste resource utilization and provides robust support for sludge solidification engineering.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012501
Dibutyl phthalate (DBP) is a ubiquitous environmental pollutant posing potential risks to aquatic ecosystems. This study assessed the developmental toxicity of DBP in Japanese medaka (Oryzias latipes) embryos. Embryos were exposed to gradient DBP concentrations (1, 5, 50, 500 μg·L−1, and 5 mg·L−1) for 15 days. Endpoints included embryonic heart rate, hatching time, survival rate, larval swimming behavior, and expression of genes related to cardiovascular, nervous, thyroid, antioxidant systems, and estrogenic effects. Results showed that 5 mg·L−1 DBP significantly reduced embryonic heart rate (P < 0.0001), leading to hatching failure and mortality. Exposure to 500 μg·L−1 DBP significantly reduced hatching rate (P < 0.01) and survival rate (P < 0.0001). DBP exposure caused developmental delay, cardiovascular hemorrhage, spinal curvature, yolk sac edema, and inhibited larval swimming behavior. At the molecular level, DBP significantly altered expression of atrap, dkk1, bnpa, fx, and dvl mRNA, affecting cardiovascular development; downregulated trha, mbp, and elavl3 mRNA, indicating endocrine disruption and neurotoxicity; upregulated cat, gpx2, and gsta mRNA, inducing oxidative stress; and upregulated vtg1, erβ1, and chgl mRNA, demonstrating estrogenic effects. This study demonstrates that DBP exposure adversely affects growth, development, hatching, survival, swimming behavior, and gene expression in Japanese medaka embryos, highlighting ecological risks of DBP pollution in aquatic environments.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025092802
Activated carbon (AC) filters in drinking water treatment plants (DWTPs) experience significant adsorption performance decline over extended operation, yet complete media replacement is a major cost. To evaluate cost-effective strategies, pilot-scale column experiments with five AC replacement ratios (0%, 30%, 50%, 70%, and 100%) were conducted to assess removal of disinfection by-product (DBP) precursors and pesticide-related emerging contaminants. For dissolved organic matter (DOM), all fractions except low molecular weight compounds (LMWC) achieved >85% of the removal obtained with full replacement when 70% new AC was used, with UV254 removal reaching 70%. LMWC, due to small molecular size and low adsorption energy, required higher replacement ratios or full replacement for substantial removal. For DBPs, removal of trihalomethanes (THMs) and haloacetic acids (HAAs) was insensitive to replacement ratio, while haloacetaldehydes (HALs) removal improved markedly with increasing ratio, indicating structural selectivity. For pesticide-related contaminants, all except triazoles achieved >95% removal at 70% replacement; triazoles, due to high water solubility, high polarity, and low octanol-water partition coefficient, achieved only ~60% removal. Overall, replacing 70% of AC restored treatment performance to >80% of that with full replacement, ensuring effluent quality while saving ~30% of new carbon cost. Molecular structure, polarity, and pore size matching are key determinants of removal efficiency; optimizing replacement ratio balances water quality and economic benefits.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510018
Scientific assessment and prediction of the stabilization process in aged municipal solid waste (MSW) landfills are critical for reliable risk evaluation and remediation decision-making. Existing methods often fail under data-scarce conditions and lack temporal predictive capability. This study establishes a 'spatial characterization–temporal prediction' framework to address these gaps. The methodology integrates grid-based sampling, laboratory analysis of biological stability indicators (AT4), and LandGEM model simulations to assess current stabilization states and predict completion timelines. Applied to a landfill in southwest China, results reveal significant spatial heterogeneity in waste stabilization, strongly correlated with waste age and influenced by leachate recirculation of membrane concentrate. None of the landfill zones had reached full stabilization; predicted times to completion were: Zone D (17 years), Zone C (13 years), Zone B (8 years), and Zone A (1 year). Based on these findings, a systematic management strategy is proposed, including zoned gradient management, targeted control of lag zones, and dynamic planning. This study provides a theoretical basis for site-specific management and serves as a reference for similar landfills.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606019
Sludge co-combustion in coal-fired power plants generates flue gas dust with high viscosity, causing severe dust deposition on downstream environmental protection equipment. This study analyzed the dust deposition mechanism in electrostatic precipitators (ESPs) and characterized the dust layer properties. Results indicated that sludge co-combustion increased flue gas moisture content, altered particle morphology, and elevated dust viscosity. To address these issues, an anode pneumatically rapped ESP technology was developed to enhance anode plate cleaning. This technology was retrofitted on a 1000 MW unit at Zhejiang Jiahua Power Plant, and performance tests under sludge co-combustion conditions were completed in February 2025. At a specific dust collection area of 118 m²·s/m³ and a unit load of 987 MW, the ESP outlet dust concentration decreased from 25.32 mg/m³ before retrofit to 7.95 mg/m³ after retrofit. Analysis revealed that sludge co-combustion caused excessive dust deposition on the first electric field anode plates, inducing back corona, high-voltage power supply flashover, and low secondary voltage and current. After retrofit, regions with low rapping acceleration were eliminated, achieving effective dust cleaning. Secondary voltage and current were significantly improved, and overall ESP efficiency was remarkably enhanced. The proposed technology provides a reference for ESP retrofitting of coal-fired units under biomass (sludge) co-combustion and low-load conditions.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606017
Against the backdrop of global green transition and tightening resource constraints, China's Dual Carbon Goals and Zero-Waste City initiative have positioned waste valorization as a critical pathway for sustainable development. Zinc, a fundamental metal, faces high external dependence and nearing primary resource limits, making the regenerated zinc industry essential. However, the previous standard YS/T 1093-2015 lagged in classification, technical indicators, and environmental requirements. This paper analyzes the revision to YS/T 1093-2024, which renames the standard to 'Recycled Zinc Raw Materials' and clarifies its role as front-end smelting intermediate feedstock. The new standard establishes a classification system covering six typical zinc-bearing materials, expanding utilization of low-grade complex materials (zinc content 5%-15%). It tightens limits on harmful elements (fluorine, chlorine, lead, arsenic) and introduces moisture control and appearance evaluation indicators, enhancing operability and environmental risk control. Compared with EU standards, it shows systematic improvements in raw material coverage, process adaptability, and environmental risk prevention. The revision is expected to drive the regenerated zinc industry toward intensification, high-value utilization, and clean production, improving resource recycling efficiency and supporting China's zinc resource strategic security and low-carbon development.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511057
To investigate the effects of applying sewage sludge aerobic fermentation products on antibiotic resistance genes (ARGs) in the rhizosphere soil and phyllosphere of pakchoi (Brassica chinensis L.), field experiments were conducted with three treatments: sludge product (sludge group), chemical fertilizer (fertilizer group), and no fertilizer (control). Antibiotic residues, abundances of ARGs and mobile genetic elements (MGEs) were measured in rhizosphere soil and phyllosphere, and microbial community composition and virulence factor (VF) contributions were annotated via metagenomics. Results showed that antibiotic concentrations in rhizosphere soil were generally higher than in phyllosphere. Compared with control, sludge application increased soil antibiotic content by 12.70%, whereas fertilizer increased it by only ~3%, indicating a more significant exogenous input from sludge. At the resistance level, total ARG abundances in rhizosphere soil and phyllosphere of the sludge group increased by 25.47% and 73.08%, respectively, relative to control, with concurrent increases in beta-lactam resistance genes and MGEs such as integron intI1. Sludge application may enhance integron-mediated gene capture and horizontal transfer potential, driving resistance risk accumulation in both phyllosphere and rhizosphere soil. Conversely, fertilizer application reduced ARG abundances by 53.40% in rhizosphere soil and 13.50% in phyllosphere compared with control, consistent with decreased microbial community abundance and diversity, suggesting that reduction of host bacteria and dissemination vectors was a key reason. In community structure, Proteobacteria dominated the phyllosphere, while Chloroflexi dominated rhizosphere soil. Correlation networks identified Sphaerobacter thermophilus and Aggregatilinea lenta positively correlated with multiple ARGs (r≈0.95–1.00), whereas Solirubrobacter sp. CPCC_204708 was negatively correlated (r≈−0.91). Virulence factor contributions followed trends similar to ARGs. Sludge fermentation products simultaneously increased ARG prevalence and related risk indicators in both rhizosphere soil and phyllosphere of pakchoi, providing a reference for risk identification and safe application of sludge fermentation products in agriculture.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025031901
The rapid expansion of the nuclear power industry has increased the demand for effective nuclear wastewater treatment, making the efficient removal of radioactive iodine isotopes (e.g., 131I, 129I) from aqueous environments a critical challenge. Covalent organic frameworks (COFs), a class of crystalline porous materials characterized by high specific surface area, tunable pore structures, and exceptional stability, exhibit significant potential for capturing radioactive iodine from water. This review systematically examines the adsorption mechanisms of iodine by COF materials, including electrostatic interactions, charge transfer, hydrogen bonding, and secondary mechanisms such as metal coordination, ion exchange, and van der Waals forces. The effects of COF pore structures on iodine removal efficacy are discussed with a focus on pore size and functional group modifications. Key research trends and prevailing challenges in the application of COFs for aqueous iodine capture are analyzed, including the need for selective adsorption in complex wastewater matrices and the scalability of COF synthesis. The review concludes with a perspective on future research directions, emphasizing the design of novel COFs with tailored pore chemistry and the development of cost-effective, regenerable adsorbents for practical deployment in nuclear wastewater treatment.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026022502
This study investigates the effects of different land use types on topsoil carbon (C) and nitrogen (N) contents and their spatial distribution in the lower reaches of the Sancha River Basin, a karst region of the Yunnan-Guizhou Plateau. Grid sampling collected 0–20 cm topsoil from forestland (n=23), cultivated land (n=25), and grassland (n=32). Total C and N were measured. Results showed that topsoil C content followed grassland (40.36±22.92 g·kg−1) > forestland (37.05±12.83 g·kg−1) > cultivated land (34.06±14.57 g·kg−1), while N content followed forestland (2.89±0.76 g·kg−1) > grassland (2.67±1.19 g·kg−1) > cultivated land (2.50±0.65 g·kg−1). One-way ANOVA revealed no significant differences among land use types (P>0.05). Soil C and N were significantly positively correlated across all land uses (r>0.5, P<0.001). Coefficient of variation (CV) indicated grassland had the highest C variability (0.57), while forestland showed the most stable C and N (CV=0.35 and 0.26, respectively). Cultivated land had CVs of 0.43 for C and 0.26 for N. Spatially, forestland exhibited concentrated high C values with significant N heterogeneity; grassland had higher C in southern and eastern areas but scattered distribution, with generally low and variable N; cultivated land showed uniform but lowest C and N. Land use types significantly drive topsoil C and N dynamics through vegetation input, soil disturbance, and management practices, underscoring the importance of rational land use planning for enhancing carbon sink functions and sustainable development in karst watersheds.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607006
This study evaluates the global warming potential (GWP) of three typical air pollution control device (APCD) configurations in municipal solid waste (MSW) incineration under ultra-low emission standards. The configurations are APCD1 (SNCR+SDS+DS+ACI+FF), APCD2 (SNCR+SDS+DS+ACI+FF+SCR+WS), and APCD3 (SNCR+SDS+DS+ACI+FF+WS+SCR). Life cycle assessment (LCA) was applied to quantify GWP. Results indicate that APCD3 exhibits the highest GWP due to increased electricity consumption, yet it achieves the lowest pollutant emissions among the three. APCD1 shows the highest NOx emissions, contributing significantly to GWP, and requires technological upgrades. APCD2 consumes more resources but does not proportionally reduce emissions, suggesting inefficiencies. Electricity consumption is the dominant factor influencing GWP across all processes; reducing electricity use and improving energy efficiency are critical for mitigating environmental impact. The study recommends further research on CO2 reduction strategies and adoption of more efficient DeNOx technologies to align MSW incineration with ultra-low emission and low-carbon goals.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3825-x
Polymer-based dielectric materials with high energy density and thermal stability are critical for modern electric/electronic industries. Polyimide (PI) based materials are promising due to their high temperature resistance and chemical inertness, yet their inherently low dielectric constant and limited charge-discharge energy density restrict applications in film capacitors. While incorporating ferroelectric or conductive fillers can enhance dielectric performance, batch-to-batch inconsistency and physical deterioration remain problematic. This study focuses on molecular structure design and modulation, preparing hyperbranched polyimides with different dianhydride monomers and branching degrees. The effects of chain packing density with polar groups on dielectric and energy storage performances were systematically investigated via experimentation and molecular simulation. Results demonstrate a significant correlation between monomers' electrical distribution and packing density in polymer systems. Molecular simulation further elucidated the underlying mechanism. This work establishes a foundation for designing polymer-based dielectric materials with high dielectric and energy storage performances at the molecular level.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4079-4
Utilization of ultrahigh-nickel LiNi_xCo_yMn_1-x-yO_2 (NCM) (x > 0.97) in Li-ion batteries can distinctively boost energy density through enhanced discharge capacity. However, capacity and thermal stability deteriorate as Ni content approaches the limit. Here, we propose a facile strategy by introducing high-valence tungsten (W) into ultrahigh-nickel polycrystalline LiNi_0.98Co_0.01Mn_0.01O_2 (PCNCM98). W-doped PCNCM98 (W-PCNCM98) exhibits refined, compactly stacked primary particles, whereas PCNCM98 shows equiaxial, non-uniform larger particles. The refined microstructure enhances mechanical strength: average particle hardness of W-PCNCM98 is 104 MPa, 1.5 times higher than PCNCM98 (68 MPa). This improved mechanical property suppresses lattice volume changes and relieves microcrack formation from H2–H3 phase transition. Consequently, cycling performance in pouch-type full cells is significantly enhanced, with capacity retention of 73% after 2000 cycles at 1 C and 25 °C, 54% higher than PCNCM98. Enhanced structural stability and strong electron affinity of W6+ also improve thermal stability: exothermic peak for W-PCNCM98 is postponed to 203 °C with heat generation of 1287 J g−1, versus 190 °C and 1528 J g−1 for PCNCM98. This high-valent doping strategy stabilizes ultrahigh-nickel NCM cathodes, accelerating large-scale EV applications.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508006
Landfill leachate, characterized by high ammonia nitrogen, high organic load, complex toxic components, and low nitrogen removal efficiency, poses significant environmental challenges. To achieve efficient nitrogen removal, a continuous-flow two-stage anoxic/oxic (A/O) moving-bed biofilm reactor (MBBR) system coupled with anaerobic ammonium oxidation (Anammox) was constructed and operated for long-term treatment of actual landfill leachate. After biofilm attachment and multi-gradient acclimation, influent concentrations were gradually increased from low levels (NH4+-N ~200 mg·L−1, COD ~2500–3000 mg·L−1) to high levels (NH4+-N ~1800 mg·L−1, COD ~8500 mg·L−1). During stable operation, average removal efficiencies of NH4+-N and COD reached 97.7% and 66.8%, respectively, with total nitrogen (TN) removal efficiency improving to 93.9%. Along the reactor, the first A/O stage achieved major organic degradation and ammonia oxidation, while the second stage facilitated nitrite accumulation and promoted Anammox for synergistic nitrogen removal. High-throughput sequencing revealed Proteobacteria as the dominant phylum (>50%), with denitrifying genera such as Azoarcus and Thauera significantly enriched. Planctomycetota abundance increased from 0.6% to 3.7%, and Candidatus Kuenenia was detected, confirming successful Anammox colonization and participation in nitrogen removal. This study validates the efficient combined nitrogen removal mechanism of the A/O–MBBR system with Anammox, providing theoretical basis and technical support for engineering treatment of high-ammonia wastewater.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509120
The 'Zero-Waste City' initiative, centered on source reduction, resource utilization, and safe disposal of solid waste, aims to minimize environmental impact. To quantitatively assess its carbon reduction contribution, this study took Mianyang as a case, systematically collecting data on solid waste generation, utilization, and disposal across industrial, agricultural, and other sectors from 2021 to 2024. Employing an improved WARM model and emission factor method, and incorporating generation, utilization, and disposal intensities, the carbon reduction benefits before (2021–2022) and after (2023–2024) the initiative were evaluated. Results show that despite significant improvements in comprehensive utilization and safe disposal rates, total solid waste generation increased, leading to a net negative carbon effect of -127.6×10^4 tCO2eq based on absolute quantities. However, after stripping economic and population growth factors, intensity-based accounting revealed a cumulative reduction of 10.8×10^4 tCO2eq, demonstrating significant synergistic benefits. The industrial sector contributed the most, with a reduction of 40.2×10^4 tCO2eq, driven by green transformation and enhanced utilization capacity. Conversely, the rising intensity of domestic solid waste generation resulted in a negative benefit of -46.1×10^4 tCO2eq, highlighting a key area for future improvement. The study underscores the necessity of considering both intensity and absolute quantity dimensions in evaluating rapidly developing cities. These findings provide practical evidence and reference pathways for advancing 'Zero-Waste City' construction and synergistic pollution reduction and carbon mitigation under the 'dual carbon' goals.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511050
Municipal solid waste (MSW) management in Inner Mongolia has long relied on landfilling, facing land scarcity and leachate management challenges. This study addresses the region's dry, cold climate, high proportion of agricultural and livestock waste, fluctuating moisture content, and weak leachate treatment capacity. An engineering optimization was implemented on an 80 t·d−1 vertical rotary gasification-incineration system featuring a dual-combustion-chamber design (primary chamber for medium-temperature pyrolysis-gasification at 550–650 °C and secondary chamber for high-temperature oxidation above 900 °C), coupled with in-situ leachate recirculation. Field measurements showed improved processing capacity and continuous operation stability. Under the project's leachate yield, in-situ recirculation achieved on-site disposal without significant adverse effects on gasification-incineration conditions, providing buffering against moisture fluctuations. During the monitoring period, major gaseous pollutant emissions remained below current national standards. The results provide engineering references for the co-processing and stable operation of small-scale county-level MSW treatment facilities.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042703
This study investigated phosphorus (P) exchange at the sediment-water interface and its microbial driving mechanisms in aquaculture ponds of Chinese mitten crab (Eriocheir sinensis). Using diffusive gradients in thin films (DGT), labile P concentrations in the upper sediment were significantly higher than in overlying water from late July to mid-August and in October, indicating sediment acts as a P source during these periods. The duration of aquaculture was a key factor; P diffusion flux declined from late July to mid-August and further decreased by October. Analyses of labile Fe, P-Fe correlations, and bacterial community composition and function suggested that dissimilatory Fe(III) reduction mediated by Fe-reducing bacteria and chemical Fe(III) reduction driven by sulfate-reducing bacteria metabolites were important mechanisms for P release. Additionally, bacterial-driven organic P mineralization and inorganic P dissolution contributed. The results indicate a high risk of P release from sediment to overlying water from late July to mid-August, potentially significantly affecting water P concentrations. Therefore, controlling sediment P release during this period is crucial.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042504
This study investigated the effect of co-aging with common cations/anions and humic acid (HA) on the combined use of Vallisneria natans (VN) and lanthanum-modified bentonite (LMB) for controlling phosphorus (P) release from sediment. Results showed that co-aging significantly reduced the phosphate adsorption capacity of LMB, with the maximum unit adsorption capacity decreasing by 33.8% compared to the unaged material. Under the combined application of VN and unaged LMB, P in sediment could still be released into pore water via dissimilatory iron(III) reduction mediated by iron-reducing bacteria and chemical reduction of iron(III) induced by sulfate-reducing bacteria metabolites, subsequently migrating to overlying water. However, the combined treatment effectively inhibited P release, achieving an average reduction efficiency of 57.1% for dissolved reactive phosphorus (SRP) in overlying water and 74.0% for labile P in sediment (measured by DGT) at an LMB dosage of 89 g·m−2. Co-aging with common ions and HA diminished the P control efficiency of the combined treatment, primarily due to reduced phosphate adsorption capacity of LMB. Therefore, mitigating the negative effects of co-aging is crucial for enhancing the long-term P control performance of the VN-LMB combined technology.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4034-3
The local concentration and configuration of active sites critically influence the selectivity of CO2 electroreduction, yet constructing well-defined structures to probe this relationship remains challenging. Here, we report a molten salt-assisted strategy to synthesize Ce-Ov-Cu cascade catalysts with tunable configurations and relative concentrations of Cu and Ce-Ov sites. Two distinct geometries were engineered: one with dense Cu sites surrounding Ce-Ov (Cu10CeOx) and another with isolated Cu centers encapsulated by Ce-Ov (CuCe10Ox). These configurations direct key intermediates (*CHO or *COH) toward either C-C coupling or deep hydrogenation, thereby switching product selectivity. CuCe10Ox achieves a CH4 Faradaic efficiency (FE) of 61.7% at -1.6 V vs. RHE, whereas Cu10CeOx favors C2 production with a maximum FE of 61.5% at -1.4 V vs. RHE. Mechanistic studies reveal that locally concentrated Cu sites exhibit strong *CO2 binding affinity, enhancing *CO surface coverage and facilitating *CO-*COH coupling. In contrast, Ce-Ov-rich regions with isolated copper centers supply abundant *H, promoting deep protonation of *CHO toward CH4. This work provides insights into catalyst design, demonstrating that manipulating structural chemistry can guide CO2RR toward targeted products.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4065-6
Industrial-scale hydrogen production from seawater is a paramount goal for a sustainable energy future, yet it is severely hampered by the rapid deactivation of electrocatalysts under harsh operating conditions. Here, we introduce a robust self-supporting aerogel catalyst designed to address the two intertwined challenges of activity and stability in high-current-density seawater electrolysis. Our strategy involves creating strong metal-support interactions by anchoring ultrasmall platinum nanoparticles onto a porous N-doped carbon aerogel (Pt@N/CFP). Theoretical calculations reveal that this unique Pt-N interface serves a dual critical function: it not only lowers the kinetic barrier for water dissociation but also creates an electronic shield that effectively prevents chloride ion poisoning of the Pt active sites. When implemented as the cathode in a practical anion-exchange membrane (AEM) electrolyzer, the Pt@N/CFP catalyst demonstrates exceptional performance, achieving a low cell voltage of 1.688 V at an industrial-grade current density of 1000 mA cm−2 and maintaining outstanding stability for over 300 h. This work provides guidance for creating exceptionally durable catalysts capable of withstanding extreme electrochemical environments.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3476-4
Ammonia synthesis remains dominated by the Haber-Bosch process, which operates at 400–500 °C and 150–300 bar, consumes 1–2% of global energy, and emits ~1.4% of global CO2. Ru-based catalysts supported on carbon and promoted with basic oxides (Ba, Cs, La) exhibit high activity under mild conditions, but conventional designs suffer from a trade-off: BaO domains block Ru active sites while attempting to donate electrons. Lee et al. (Nat Catal, 2025, 8: 248–256) resolved this by using conductive carbon to bridge isolated Ru and BaO domains, enabling long-range H+/e− pair migration. Screening eleven carbon supports, they identified N-doped multi-walled carbon nanotubes (10–20 nm diameter, N-MWNT-1) with the lowest work function as optimal. At a Ba/Ru molar ratio of 0.75, the catalyst achieved an NH3 production rate 7.4 times higher than conventional BaO-promoted Ru catalysts under 573 K and 1.0 MPa, using high-purity H2 and N2 (99.999%, O2 <0.4 ppm, H2O <0.7 ppm). This design decouples proton and electron storage, preventing BaO-induced blockage of Ru surfaces and enabling superior activity and stability. The Ba-Ru/carbon catalyst offers a transformative pathway for reducing energy consumption and integrating with electrolytic hydrogen production in industrial ammonia synthesis.