SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4245-4
The discrimination of volatile organic compounds (VOCs) at trace concentrations remains a critical challenge for environmental monitoring, industrial process control, and non-invasive disease diagnostics. Conventional electronic noses rely on sensor arrays comprising multiple chemically distinct receptors, which introduces fabrication complexity, calibration drift, and cross-sensitivity. Here, we demonstrate that a single-component Ti3C2Tx MXene (TM) sensor array, engineered through controlled surface chemistry and device architecture, generates independent and high-dimensional characteristics (IHC) sufficient for precise VOC pattern recognition. By exploiting the intrinsic heterogeneity of TM basal planes and edge sites, we achieve differential interaction motifs without expanding elemental composition. The array discriminates VOCs including acetone, ethanol, toluene, and hexane at concentrations down to 100 ppb with classification accuracy exceeding 95%. Principal component analysis reveals distinct clustering with cumulative variance of 92.3% captured by the first three principal components. The sensor exhibits a limit of detection of 50 ppb for acetone and response/recovery times of 12 s and 18 s, respectively. Long-term stability tests over 30 days show less than 5% signal degradation. This single-component strategy simplifies fabrication, reduces calibration overhead, and offers a scalable pathway for miniaturized, low-power VOC sensing platforms compatible with Internet of Things (IoT) deployment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4294-4
Room-temperature phosphorescence (RTP) polymer materials are attractive for flexible electronics and information encryption due to their tunability and processability. However, achieving polymeric RTP systems that simultaneously exhibit high thermal sensitivity, reversible multicolor emission, and long phosphorescence lifetime (τPhos) with high quantum yield (ΦPhos) remains challenging. Here, we report an in-situ cross-linked self-assembly strategy that converts flexible polymers into rigid polymer microspheres, yielding long τPhos, high ΦPhos, and thermally and time-dependent tunable RTP. The resulting microspheres (PM0.1-0.01-1) exhibit a maximum τPhos of 1754 ms and ΦPhos of 42.83%, markedly superior to previously reported intrinsic polymer RTP materials. At 77 K, they display ultralong green emission with a lifetime of 6019 ms and visible afterglow lasting up to 99 s. The cross-linked microspheres enable time-dependent, continuously tunable RTP and thermally responsive color switching, while maintaining excellent phosphorescence stability in aqueous and high-temperature environments. This provides a versatile platform for dynamic information encryption, full-color afterglow LEDs, and temperature sensing. The strategy establishes a general design principle for developing multidimensional, controllable, and stable high-performance polymer RTP materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4277-1
Two-dimensional (2D) magnetic materials hold promise for next-generation spintronics, yet most exhibit Curie temperatures (Tc) far below room temperature, limiting practical applications. Here, we report the realization of room-temperature ferromagnetism in CuCrSe2 nanosheets via controlled anion removal achieved by post-synthetic vacuum annealing. Raw CuCrSe2 shows a low Tc of ~120 K, whereas annealed CuCrSe2 (A-CuCrSe2) nanosheets exhibit robust ferromagnetic ordering above 300 K. Structural and compositional analyses, including transmission electron microscopy, Raman spectroscopy, and X-ray absorption spectroscopy, confirm that A-CuCrSe2 retains the original layered crystal structure with an estimated Se vacancy concentration of approximately 10%. Magnetic measurements reveal room-temperature ferromagnetism in exfoliated nanosheets, corroborated by magnetic imaging and electric transport measurements. Anomalous Hall effect (AHE) measurements uncover the coexistence of two ferromagnetic phases within the same sample: one with low Tc (~120 K) and another with high Tc (>300 K), indicating spatially heterogeneous magnetic ordering driven by anion removal distribution. Density functional theory (DFT) calculations elucidate the microscopic mechanism, suggesting that Se vacancies modulate the magnetic exchange interactions, enhancing Tc. This work demonstrates that anion modulation is an effective intrinsic strategy to achieve room-temperature ferromagnetism in 2D materials, potentially advancing spintronic applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4203-7
The solution process holds great promise for organic light-emitting diode (OLED) fabrication owing to its minimal material loss, simple processing and low equipment investment. However, solution-processed blue OLEDs still face the challenges of low electroluminescence efficiency and poor working stability. In this study, two new cross-linkable blue light-emitting molecules, v-4CzBn and v-5CzBn, were synthesized. They featured a multicarbazole-substituted benzonitrile donor–acceptor structure as the emitting core, with two vinyl phenyl units on the carbazole rings serving as cross-linking groups. A singlet–triplet energy gap of ΔEST ≤ 0.10 eV and a high reverse intersystem crossing rate (kRISC > 10^6 s−1) were achieved because the three-dimensionally confined covalent network structure formed through a thermal cross-linking reaction limited intramolecular motions and vibrational relaxations of luminescent units. Moreover, this structure suppressed irreversible morphological changes and structural deterioration of light-emitting units due to aggregation or crystallization, improving the light-emitting performance of the device. Nondoped solution-processed OLEDs with the structure of ITO/PEDOT:PSS/TFB/S-4CzBn/TPBi/LiF/Al exhibited blue emission with a peak at 488 nm, achieving a maximum external quantum efficiency of 12.01%, a maximum luminance of 11,141.15 cd m−2, and a T50 lifetime of 1375.66 h@100 cd m−2. This result represents the longest operational lifetime reported to date for solution-process devices with cross-linked emitting layers.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4134-6
Oral leukoplakia (OLK) is a prevalent premalignant lesion with malignant transformation risk. Current adhesive hydrogels lack lesion-specific adhesion and precision therapy. We synthesized DNA hydrogels via co-crosslinking of thiolated gelatin and thiolated oligonucleotide through disulfide bonds, incorporating Mn2+ and chlorin e6 (Ce6) via thiol-metal coordination and physical entrapment. Low-frequency ultrasound (LFUS) anchored complementary oligonucleotides onto the lesion surface, enabling site-specific bioadhesion through base pairing. Under high-frequency ultrasound (HFUS), Ce6 generated reactive oxygen species, triggering mitochondrial DNA (mtDNA) release in hyperproliferative epithelial cells. Concurrent HFUS accelerated Mn2+ release, potentiating cGAS recognition of cytosolic mtDNA and activating the cGAS-STING pathway. This induced dendritic cell maturation, priming naïve T cells into cytotoxic T lymphocytes, reversing the immunosuppressive microenvironment. The modality induced immunological memory, restraining OLK recurrence and impeding malignant transformation. This study introduces the first DNA-directed hydrogel bioadhesion strategy and proposes unprecedented cGAS-STING pathway-associated immunotherapy against OLK.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3848-7
Conventional heterogeneous photocatalysts often suffer from insufficient light absorption, rapid charge recombination, and a lack of specific reactive sites for efficient photocatalytic oxidation. To overcome these limitations, we propose a molecular polarization engineering approach utilizing structurally well-defined donor (D)-acceptor (A) covalent triazine frameworks (CTFs). The construction of dipole-induced built-in electric fields within the D-A-structured CTFs enables enhanced exciton dissociation and facilitates directional charge transfer. Specifically, the asymmetric A1-D-A2 moiety enhances molecular polarization in the dual-acceptor system CTF-TBT (A1-D-A2), enabling efficient charge separation through multiple electron-withdrawing units. This structural design promotes directional electron transfer toward the secondary acceptor (benzothiazole, A2), while simultaneously concentrating holes on the donor unit. Consequently, the A2 moiety acts as a site for efficient O2 activation via electron accumulation, whereas the highly oxidized donor unit provides strongly positive holes (h+) that facilitate substrate oxidation. Experimental and DFT calculation results confirm that CTF-TBT demonstrates highly enhanced photocatalytic oxidation performance, which can be attributed to its multi-channel charge separation mechanism and spatially separated redox-active sites. This study highlights the effectiveness of molecular dipole engineering in designing heterogeneous photocatalysts with controlled charge transfer pathways and improved redox capabilities. The proposed design principles provide a universal approach for promoting solar-driven chemical synthesis applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3645-3
Postoperative abdominal adhesion, a complication with morbidity exceeding 90%, imposes severe clinical and economic burdens. Existing bioadhesive barriers often exhibit unreliable adhesion to the slippery abdominal wall, risk mispositioning, and neglect frictional stimuli and inflammation. Inspired by the lubricated peritoneum, we developed a programmable adhesive dual-layer Janus patch (DJP) barrier integrating a lubricated layer and an adhesive matrix. DJP achieves rapid, noncovalent interfacial adhesion, subsequently enhanced 2.81-fold via covalent interactions, enabling repositioning within a short time window to improve surgical fault tolerance. The micron-scale poly(sulfobetaine methacrylamide) brush on the DJP surface provides hydration lubrication with a low coefficient of friction (0.06), mimicking peritoneal lubrication and reducing frictional damage to injured tissue. The catechol-containing copolymer confers antioxidative and anti-inflammatory properties, confirmed in vitro. In a rat model, DJP adhering to the injured site significantly reduced collagen deposition between the abdominal wall and cecum, preventing adhesion and promoting tissue healing compared to commercial barriers. This work provides a guiding reference for developing antiadhesive biomaterials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3575-4
Halide perovskite memristors, known for their ion mobility, have emerged as strong candidates for computational units in next-generation memory and neuromorphic computing systems. Nevertheless, most memristors are limited to operating in a single mode, either resistive switching or threshold switching. In this work, we overcome this limitation by developing dual-mode α-formamidinium lead triiodide (α-FAPbI3) perovskite memristors with switchable volatile/nonvolatile states, enabled by engineered SnO2 electron transport layers (ETLs). Through molecular interface optimization using 3-(N,N′-dimethylmyristylammonio) propanesulfonate (Z14) and 4,4′-(1,10-phenanthroline-3,8-diyl)bis(N,N′-bis(4-methoxyphen-yl)aniline) (PNL), we achieved exceptional device stability. Volatile devices exhibited >500 switching cycles, while nonvolatile devices surpassed 1000 cycles, both maintaining a high on/off ratio (~10^3). Beyond memory applications, these devices successfully emulated biological functionalities. The volatile mode replicated four key nociceptor characteristics (threshold, relaxation, sensitization, and no adaptation), while the nonvolatile mode demonstrated advanced synaptic plasticity, including paired-pulse facilitation (PPF) and spike-timing-dependent plasticity (STDP). Capitalizing on this dual-mode synergy, we constructed a spiking neural network (SNN) for handwritten digit recognition, achieving a 93% accuracy rate—a significant milestone for perovskite-based neuromorphic systems. This study not only provides a material-level strategy for multifunctional memristor design but also bridges the gap between biological sensing and artificial intelligence, paving the way for adaptive neuromorphic hardware.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3714-3
Eco-friendly aqueous zinc batteries (AZBs) are promising alternatives to lead-acid batteries in applications requiring both safety and energy density. However, their practical deployment is hindered by the synergistic deterioration of zinc anodes—structural collapse and kinetic failure—under high depth of discharge (DOD) and high current densities, which severely limits actual energy and power densities. Here, we report a strategy for the in situ integration of a double-layer topological chitosan framework (D-CTS) on current collectors via regulating phase separation kinetics during multistage coordination-neutralization electrophoresis. The vertical through-hole array is formed by coupling instantaneous and delayed phase separation. Subsequently, a columnar zinc array is mediated by D-CTS to construct an integrated component (D-CTS-Zn) comprising a vertical through-hole separator and an array anode. The embedded interconnected nanonetworks within the through-hole walls enable dynamic equilibrium of the columnar zinc array through a lateral ion compensation mechanism. As a result, Zn||Zn symmetric cells with D-CTS-Zn stably cycle over 3000 cycles at 200 mA cm−2 under 60% DOD. The assembled D-CTS-Zn||MnO2 battery delivers an energy density of 83 Wh kg−1 at an ultrahigh power density of 9.25 kW kg−1. This work provides a constructive strategy for chitosan phase separation regulation and separator-induced reversible metal array anodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3860-0
Drug detection is critical for public health and security, yet reversible and highly sensitive sensing materials remain scarce. This study presents a novel ionogel sensor material, poly(ethylene glycol) diacrylate (PEGDA)/1-butyl-3-methylimidazole tetrafluoroborate, for reproducible detection of N-methylphenylethylamine (MPEA), a structural analogue of methamphetamine. The ionogel is fabricated by immobilizing a flowable ionic liquid within a PEGDA network via UV curing, preserving ionic mobility for efficient conduction. Integrated on a flexible poly(ethylene naphthalate) substrate, the sensor exhibits over 72.6% transmittance in the visible spectrum, enabling concealed attachment. Utilizing non-covalent interactions, the sensor achieves reproducible MPEA detection at sub-ppb levels at room temperature, with a theoretical detection limit of 317 ppt. It demonstrates high selectivity and consistency. Ionic conductivity was confirmed via current-voltage tests and impedance spectroscopy, and the sensing mechanism was clarified. The device maintains reliable performance under bending, indicating suitability for dynamic environments. With Bluetooth integration for wireless data transmission, the sensor shows strong potential for practical, discreet drug monitoring in real-world applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3705-5
Biodegradable metals (BMs) are designed to corrode gradually in physiological environments, yet this corrosion can compromise their mechanical integrity, potentially causing premature implant failure. For emerging zinc-based alloys, the corrosion-mechanical property relationship remains inadequately characterized. This study systematically investigated the long-term corrosion-associated mechanical behavior of hot-extruded Zn-Cu and Zn-Cu-Fe alloys, promising Zn-based bio-metals, in comparison with pure Zn, under immersion degradation in Hank's solution. Electrochemical impedance spectroscopy and mechanical testing revealed that the evolving corrosion profile governs mechanical performance. Alloying with Cu and Fe mitigated corrosion's detrimental effects: grain refinement reduced localized corrosion susceptibility, while finely dispersed second phases acted as cathodic sites, promoting uniform corrosion. Additionally, Cu and Fe facilitated the formation of protective corrosion product layers, suppressing further matrix attack. Consequently, the overall reduced corrosion, particularly localized corrosion, lowered stress concentration susceptibility, delaying mechanical decline and preserving structural integrity. These findings elucidate the degradation-mechanical property correlation in Zn-based bio-metals and underscore critical considerations for developing new bio-metals for clinical translation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3586-7
Ischemic stroke is a leading cause of mortality and long-term disability worldwide, with endovascular stent intervention emerging as a key therapeutic strategy. Biodegradable Mg-Zn-Y-Nd alloy (ZE21B) offers promising mechanical properties and biocompatibility for vascular scaffolds, yet suffers from inadequate corrosion resistance, insufficient endothelialization, and impaired blood-brain barrier remodeling. This study develops a composite coating comprising barnacle cement protein cp19k and sulfonated hyaluronic acid nanoparticles (NP@S-HA) applied via electrostatic spraying onto ZE21B. The cp19k/NP@S-HA coating enhances corrosion resistance by approximately 40.6% relative to uncoated ZE21B, as determined by electrochemical and static immersion tests. In vitro blood and cellular assays demonstrate that the coating promotes endothelial cell proliferation and migration, inhibits smooth muscle cell proliferation while regulating contractile phenotype, suppresses macrophage adherence and induces M2 polarization, reduces TNF-α expression, and mitigates fibroplasia. These findings indicate that the cp19k/NP@S-HA composite coating provides an effective surface modification strategy for biodegradable magnesium alloys in cerebrovascular applications, potentially improving stent performance and patient outcomes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3730-3
Water scarcity, exacerbated by organic micropollutant contamination and climate change, necessitates energy-efficient, eco-friendly purification technologies. Membrane separation has emerged as a transformative solution, outperforming energy-intensive processes such as distillation. Traditional chemical separations, dominated by distillation, consume 10%–15% of global energy, whereas advanced membrane technologies can reduce energy use by up to 90%. However, membrane separation is hampered by reliance on toxic petrochemical feedstocks and persistent microplastic pollution from nonbiodegradable end-of-life membranes. Shao's group addresses both gaps with a sustainable nanofiltration membrane (SNFM) crafted entirely from low-hazard, renewable components. The substrate polylactic acid (PLA), a biodegradable polyester derived from corn starch, is processed via modified nonsolvent-induced phase separation (NIPS) to form a porous yet strong support. For the selective layer, toxic aromatic monomers are replaced with xylitol (a plant sugar alcohol) and dopamine (DA, a biogenic amine), and green solvents such as dimethyl sulfoxide are used to avoid volatile organic compound emissions. Compared with commercial alternatives, this design yields a membrane with exceptional dual functionality: it maintains high separation performance (928% greater permeance, 92% bisphenol A rejection, and 89% Na2SO4 rejection) and low fouling (protein adsorption ≤12 μg cm−2) over 30 days. A life cycle assessment reveals a 62% reduction in carbon footprint compared with petrochemical-based membranes, whereas soil biodegradation tests confirm 90% breakdown within 6 months, driven by Delftia and Tissierella microbes. By eliminating microplastic waste and toxic inputs, this SNFM bridges the divide between performance and environmental responsibility, offering a scalable blueprint for next-generation green membranes in water treatment and beyond.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506005
The escalating generation of medical waste, driven by healthcare expansion and frequent medical activities, poses significant environmental and public health risks. Under the framework of ecological civilization, China is developing a comprehensive policy system for medical waste treatment and disposal, yet the current framework remains nascent and exhibits inconsistencies between national and local policies. This study systematically analyzes the status of national and local policies from 2003 to 2024, collecting 413 policy documents (166 from national ministries and 247 from provincial governments). The analysis examines temporal evolution, regional distribution, and policy focus, alongside the influence of medical waste output, treatment technologies, facility infrastructure, and major epidemic responses. Findings reveal distinct policy phases: initial self-disposal, exploratory management, foundational system building, and rapid development. Regional disparities are pronounced, with eastern coastal areas showing more advanced policies due to greater technical and financial resources. The surge in medical waste, particularly during the COVID-19 pandemic, underscores the need for enhanced regulatory guidance. Non-incineration technologies are gaining traction for their environmental and cost benefits, and facility coverage has improved but remains uneven. The study proposes five policy principles to foster technological innovation and industrial upgrading, ensuring safe medical waste management and environmental protection.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025101101
Acetamiprid, a representative neonicotinoid insecticide, persists in soil and water, posing ecological risks. This study evaluated its transgenerational toxicity in Caenorhabditis elegans exposed to 1, 10, and 100 μg·L−1. Direct exposure (F0) caused neurobehavioral abnormalities, with head swing frequency significantly increased by 23.86% even at 1.0 μg·L−1, correlating with disrupted acetylcholinesterase and γ-aminobutyric acid. Reproduction, development, metabolism, and intestinal barrier were impaired, with reactive oxygen species elevated by 30.42%–48.28%, indicating oxidative stress as a mechanism. Effects transmitted to unexposed T1–T3 generations: at 1.0 μg·L−1, body width inhibition persisted to T2; fat accumulation and intestinal permeability effects intensified with concentration. Among oxidative stress biomarkers, superoxide dismutase showed highest sensitivity and transgenerational persistence. This study reveals multidimensional transgenerational toxicity, informing soil ecological risk assessment of neonicotinoids.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112101
The biological reduction of Cr(VI) to less hazardous Cr(III) is a promising strategy for remediating Cr(VI)-contaminated sites. Both biochar and riboflavin can act as electron shuttles to accelerate this bioreduction process, yet their combined effects remain poorly understood. Using Shewanella oneidensis MR-1 as a model reducing bacterium, we investigated the joint influence of biochar (average particle size 28.85 μm) and riboflavin at high (1 mmol·L−1) and low concentrations on Cr(VI) bioreduction. Individually, biochar and high-concentration riboflavin enhanced indirect electron transfer, accelerating Cr(VI) removal. However, when combined, the fast-phase reaction rate (rf0) did not significantly improve compared to single amendments. The combined action factor revealed an antagonistic inhibition between biochar and riboflavin. Mechanistically, high-concentration riboflavin saturated biochar's adsorption sites (equilibrium concentration 0.96±0.04 mmol·L−1), hindering biochar's role as an electron conduit. With a bacterial density of 3.4×10^7 cells·mL−1, the inter-bacterial distance (30.87 μm) exceeded biochar's particle size, and the per-cell riboflavin concentration (2.9×10−2 pmol·cell−1) was sufficient for riboflavin to dominate as the primary electron shuttle, while biochar's surface became coated, reducing its efficacy. These findings reveal the complex interplay between biochar and soluble organic matter in Cr(VI) bioreduction, underscoring the need to consider such antagonistic effects when designing bioremediation strategies for multi-component contaminated environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3485-0
Aqueous Zn-ion batteries (AZIBs) are promising for next-generation energy storage due to high safety and low cost, but their practical use is limited by Zn dendrite growth and side reactions. An ideal anode/electrolyte interphase should block water contact while enabling fast Zn2+ transport, yet conventional thick interphases increase ionic resistance and polarization. Here, we report a hydrophobic yet ultrathin (~5 nm) polydimethylsiloxane (PDMS) artificial interphase fabricated via conformal coating. The oxygen-rich PDMS layer selectively coordinates Zn2+ while its superhydrophobicity excludes water, and the ultrathin nature enables rapid Zn2+ conduction, enhancing the Zn2+ transference number by 2.28-fold. This synergistic design suppresses dendrites and mitigates hydrogen evolution. The PDMS-modified anode achieves 99.9% Coulombic efficiency over 3500 cycles, 880-hour symmetrical cell operation at 60% depth of discharge, and 2500-cycle full-cell endurance under lean Zn conditions (N/P ratio 5.7). Proof-of-concept pouch cells sustain 1400 cycles with a 0.01% decay rate. This molecular-scale interphase strategy provides a feasible pathway toward practical AZIB implementation.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012901
N2O is a potent greenhouse gas, and its catalytic decomposition is of significant environmental importance. In this study, three CeO2 supports with different morphologies—nanorods (NR), nanocubes (NC), and nanooctahedra (NO)—were prepared via a hydrothermal method. Rh catalysts supported on these CeO2 materials were synthesized using a deposition-precipitation method, and their catalytic performance for N2O decomposition was evaluated. Results demonstrate that Rh/CeO2-NR exhibits superior catalytic activity compared to Rh/CeO2-NC and Rh/CeO2-NO under identical reaction conditions, including in the presence of O2 and H2O. Characterization reveals that Rh/CeO2-NR possesses abundant oxygen vacancies and a relatively high number of intrinsic defect sites, which facilitate the transfer of O intermediates. Additionally, Rh/CeO2-NR exhibits an appropriate Rh0/Rhn+ ratio, promoting the redox cycle between Rh species and reactants, thereby enhancing catalytic activity. The study underscores the critical role of CeO2 support morphology in optimizing Rh-based catalysts for N2O decomposition, offering a strategy to improve catalytic efficiency and stability for industrial applications.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605020
To address the high CO2 emission proportion in the industrial sector, distillers' grain waste was converted into biochar for CO2 adsorption from flue gas. Raw biochar suffers from weak pore adsorption and poor selectivity at elevated temperatures. This study employed ash self-templating and particle self-assembly to create hierarchical pores and simultaneously load amine groups onto distillers' grains-derived biochar, yielding amine-functionalized hierarchical porous carbon spheres. The amine loading significantly increased, providing more CO2 adsorption sites, while retaining macroporosity (total pore volume 0.0030–0.0066 cm3/g after amine loading), which enhanced morphological stability and CO2 mass transfer. The optimal sample, 0.2PW-K-CNF-PEI, exhibited a CO2 adsorption capacity of 1.03 mmol/g at 100 °C, a CO2 diffusion coefficient of 0.0495 min−1, and a selective adsorption capacity of 44 mg/g at 80 °C. This work offers a solution for valorizing distillers' grain by-products and capturing CO2 from low-temperature flue gas.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225264
The high cost of high-purity hydrogen necessitates the utilization of low-cost industrial by-product hydrogen as an alternative gas source to reduce hydrogen storage costs. Industrial by-product hydrogen typically contains impurities such as H2S and CO, yet the poisoning mechanisms of these gases on superlattice hydrogen storage alloys during hydrogen absorption/desorption remain poorly understood. This study systematically investigates the poisoning effects and regeneration behavior of La0.65Mg1.32Ca1.03Ni9Y0.17 superlattice hydrogen storage alloy in atmospheres containing 10^-3 H2S and CO. The experimental protocol comprised 10 poisoning cycles followed by 1 regeneration, repeated to total 20 poisoning cycles and 2 pure hydrogen regenerations. Results show that in pure hydrogen, the alloy's hydrogen storage capacity gradually decreases after 22 cycles but is effectively restored after dehydrogenation at 473 K. In the presence of impurity gases, the hydrogen storage capacity retention rates after 10 poisoning cycles with H2S and CO are 3.56% and 2.71%, respectively; after 20 cycles, these decrease to 3.68% and 1.73%, respectively. After dehydrogenation at 473 K, retention rates recover to 40.35% and 98.27%, respectively. This indicates that poisoning severity follows the order CO > H2S, while regeneration difficulty follows H2S > CO. X-ray diffraction analysis reveals that after poisoning, the main phase transforms from AB3 to AB3H, but reverts to AB3 after high-temperature dehydrogenation. X-ray photoelectron spectroscopy shows that after H2S poisoning, CaS and CaSO4 form on the alloy surface, indicating irreversible chemical adsorption. In contrast, after CO poisoning, no new substances are detected, indicating reversible adsorption. This study clarifies the differentiated poisoning mechanisms of impurity gases and provides theoretical support for the application of rare-earth superlattice hydrogen storage alloys in complex atmospheres.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3766-0
Leuco dye-based thermochromic fibers suffer from poor light fastness, limiting their cyclability. Here, a hydrogen bond dissociation/structural isomerization-based dual ultraviolet (UV)-shielding strategy is proposed to develop enhanced light-resistant thermochromic elastomer fibers (Azo/TCM@Abs/TPU) employing UV absorbers and 4-dodecyloxyazobenzene (C12-Azo) through a coaxial wet-spinning process. The integration of UV absorbers and C12-Azo enhances UV protection, effectively blocking nearly the entire UV spectrum. The light fastness of Azo/TCM@Abs/TPU has been improved to Grades 3–4, enabling a stable thermochromic function to withstand several months of sunlight exposure. Additionally, the absorbed UV light is stored as chemical energy within C12-Azo via trans-to-cis photoisomerization. This stored energy can be released as heat on demand. The coaxial dual-protection concept using photoisomerization offers an efficient method to enhance light resistance in thermochromic fibers.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60649-4
To achieve efficient conversion of lignin-derived phenolic compounds into high-value hydrocarbon fuels, a series of NiCo bimetallic catalysts with N-doped biochar and Al2O3 composite supports (NiCo/NC-Al2O3) were designed and synthesized. Comprehensive characterizations (XRD, TEM, XPS, H2-TPD) revealed the superior catalytic activity in the hydrodeoxygenation (HDO) of lignin-derived phenolic compounds. The optimized Ni8Co2/NC-Al2O3 catalyst exhibited good metal dispersion and excellent hydrogen dissociation adsorption capacity. Under mild reaction conditions (240°C, 1 MPa H2, 4 h), it achieved complete conversion of guaiacol and 99.9% selectivity to cyclohexane, significantly outperforming monometallic Ni10/NC-Al2O3 and Co10/NC-Al2O3 catalysts. Comparative studies indicated a synergistic effect between Ni and Co, where the introduction of Co effectively promoted aromatic ring hydrogenation and C−O bond cleavage. The catalyst maintained high activity after four reuse cycles, demonstrating outstanding structural stability. This study elucidates the regulatory mechanism of the Ni-Co synergistic effect on catalytic performance, providing new insights for the development of efficient non-noble metal HDO catalysts.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025022801
Paddy soils are a major source of agricultural methane (CH4) emissions. Biochar is widely applied to paddy soils, while dissolved organic matter (DOM) is ubiquitous; both can regulate CH4 emissions by mediating electron transfer processes, yet their synergistic mechanisms remain unclear. This study investigated the individual and combined effects of biochar and the DOM model compound anthraquinone-2,6-disulfonic acid (AQDS) on CH4 emissions from paddy soil during incubation. Biochar amendment increased DOM concentration and accelerated extracellular electron transfer, resulting in a maximum cumulative CH4 emission of (66.23±16.20) μmol, four-fold higher than the control (15.14±0.18) μmol. In contrast, AQDS addition markedly suppressed CH4 accumulation to (1.04±0.09) μmol, attributed to sulfate introduction as a competitive electron acceptor, despite enhanced electron exchange. The combined biochar-AQDS treatment yielded intermediate CH4 accumulation of (12.71±0.32) μmol. Although DOM availability increased, sulfate-driven electron competition inhibited methanogens, and the combined treatment favored the acetoclastic methanogenesis pathway, which produces less CH4 per unit acetate, resulting in lower emissions than biochar alone but higher than AQDS alone, indicating an additive effect. These findings elucidate the mechanisms by which biochar and DOM jointly regulate CH4 emissions from paddy soils, providing a theoretical basis for agricultural management.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606019
Sludge co-combustion in coal-fired power plants generates flue gas dust with high viscosity, causing severe dust deposition on downstream environmental protection equipment. This study analyzed the dust deposition mechanism in electrostatic precipitators (ESPs) and characterized the dust layer properties. Results indicated that sludge co-combustion increased flue gas moisture content, altered particle morphology, and elevated dust viscosity. To address these issues, an anode pneumatically rapped ESP technology was developed to enhance anode plate cleaning. This technology was retrofitted on a 1000 MW unit at Zhejiang Jiahua Power Plant, and performance tests under sludge co-combustion conditions were completed in February 2025. At a specific dust collection area of 118 m²·s/m³ and a unit load of 987 MW, the ESP outlet dust concentration decreased from 25.32 mg/m³ before retrofit to 7.95 mg/m³ after retrofit. Analysis revealed that sludge co-combustion caused excessive dust deposition on the first electric field anode plates, inducing back corona, high-voltage power supply flashover, and low secondary voltage and current. After retrofit, regions with low rapping acceleration were eliminated, achieving effective dust cleaning. Secondary voltage and current were significantly improved, and overall ESP efficiency was remarkably enhanced. The proposed technology provides a reference for ESP retrofitting of coal-fired units under biomass (sludge) co-combustion and low-load conditions.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606018
Swine wastewater, a high-strength organic effluent, offers a viable substrate for anaerobic biohydrogen production, aligning with clean energy recovery. This study compared hydrogen production in three anaerobic sequencing batch reactors (ASBRs) treating: raw wastewater (R1), supernatant after MAP (magnesium ammonium phosphate) precipitation for nitrogen and phosphorus recovery (R2), and the same supernatant with anaerobic sludge heat-treated at 75°C for 0.5 h (R3). Without pH adjustment, hydrogen production in R1 remained below 0.50 mmol/(kg·d). At an influent COD of 1800 mg/L, R2 and R3 achieved hydrogen production rates of 48.17 and 71.44 mmol/(kg·d), respectively. At COD 2400 mg/L, methane concentrations in R1, R2, and R3 were 10.8%, 14.2%, and 9.1%, respectively, indicating MAP pretreatment enhanced both hydrogen and methane production. As COD increased, R1's methane concentration rose to 14.6%, while average COD removal efficiencies for R1, R2, and R3 were 78.9%, 70.8%, and 52.5%, respectively. Under pH adjustment, all reactors peaked at pH 4.0, with hydrogen production rates of 0.10, 7.74, and 8.83 mol/(kg·d) for R1, R2, and R3, respectively. These findings demonstrate that MAP pretreatment combined with sludge heat treatment significantly enhances biohydrogen production, offering a promising strategy for swine wastewater valorization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-3961-8
This correction addresses an inadvertent misplacement of Fig. 4b3 during figure reorganization in the original article published in Science China Materials, volume 65, issue 10, 2022, page 2850 (DOI: 10.1007/s40843-022-2024-6). The corrected Fig. 4b is presented herein. The authors confirm that this correction does not affect the results, conclusions, text, or figure caption of the original work. The correction was requested by the authors and received on 6 January 2026, accepted on 8 January 2026, and published online on 10 February 2026. The original study introduced flexible electrostatic hydrogels derived from marine organisms for nitric oxide-enhanced photodynamic therapy against multidrug-resistant bacterial infections. The correction ensures the accurate representation of experimental data, maintaining the integrity of the scientific record.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60675-5
Hydrogen as an energy carrier offers a promising route to mitigate environmental issues from fossil fuel use. Efficient and inexpensive electrocatalysts for the oxygen evolution reaction (OER) in alkaline media are critical for advancing alkaline water electrolyzers. Transition metal phosphides (TMPs) are promising (pre-)catalysts for OER. This dataset compiles and compares the electrocatalytic OER activity of nickel- and cobalt-based phosphides. The phosphides were synthesized via solvothermal phosphidization or electrodeposition, and their OER activities were evaluated using linear sweep voltammetry in 1 mol/L KOH. Cyclic voltammetry and electrochemical impedance spectroscopy were also performed. The dataset comprises 312 files totaling 14.5 MB. It provides key electrocatalytic parameters and enables analysis of the influence of metal doping, solvothermal conditions (solvent and precursors), and crystallinity on OER activity. This dataset serves as a benchmark for evaluating Ni and Co phosphide materials for alkaline OER and provides a foundation for designing more active TMP-based electrocatalysts through comparative analysis. The materials may also be applied to other reactions such as hydrogen evolution, alcohol oxidation, and CO2 reduction, relevant to fuel cells, electrolyzers, and metal-air batteries, as well as in lithium/sodium-ion batteries and anticorrosion coatings.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026030202
High nitrogen (N) inputs, low N use efficiency, and substantial greenhouse gas emissions constrain sustainable double-cropping rice production in the middle and lower reaches of the Yangtze River. To evaluate whether humic acid urea (HAU) can reconcile yield stability with N reduction and carbon mitigation, a field experiment was conducted in a double-cropping rice system. Five treatments were established: conventional urea at the recommended N rate (U), HAU at the recommended N rate (HAU), conventional urea with a 20% reduction in N input (U-20), HAU with a 20% reduction in N input (HAU-20), and a no-N control (CK). Rice yield, N uptake and utilization, and the full life-cycle carbon footprint were quantified. Results showed that HAU significantly increased double-cropping rice yield by 6.46% (early rice) and 8.76% (late rice) compared to U (P < 0.05). HAU-20 maintained yield equivalent to U, while U-20 significantly reduced yield. HAU-20 significantly improved nitrogen fertilizer apparent utilization rate, agronomic efficiency, and partial factor productivity. Specifically, apparent utilization rate increased by 9.24 percentage points (early rice) and 7.80 percentage points (late rice); agronomic efficiency increased by 18.51% and 26.69%, and partial factor productivity by 22.79% and 25.58% for early and late rice, respectively (P < 0.05). Life-cycle carbon footprint was significantly reduced by 26.25% (early rice) and 40.38% (late rice) under HAU-20 compared to U, with per-unit product carbon footprint reduced by 0.22 t CO2-eq·t−1 and 0.86 t CO2-eq·t−1, respectively. The reduction was primarily attributed to decreased CH4 and N2O emissions: early rice CH4 and N2O cumulative emissions decreased by 28.92% and 44.34%, and late rice by 44.46% and 63.85% (P < 0.05). In conclusion, HAU with 20% N reduction sustains yield, enhances N use efficiency, and significantly lowers carbon footprint, offering a viable path for green and low-carbon double-cropping rice production.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607003
Co-firing municipal sludge with municipal solid waste (MSW) provides a viable solution for sludge disposal. This study evaluated the effect of sludge co-firing rate (0%, 5%, and 10%) on flue gas pollutant emissions, operational performance, and incineration byproduct characteristics in a waste-to-energy plant. The results showed that under all co-firing rates, the concentrations of SO2, NOx, CO, HCl, particulate matter, and dioxins complied with the limits specified in the Standard for Pollution Control on Municipal Solid Waste Incineration (GB 18485—2014). As the co-firing rate increased from 5% to 10%, concentrations of all flue gas pollutants except NOx and HCl exhibited an upward trend. The optimal operational performance under the test conditions was achieved at a 5% co-firing rate, when the flue gas volume, fan volume, and ammonia and lime consumption were minimized. Compared to the 5% rate, increasing the co-firing rate to 10% resulted in elevated flue gas volume, fan volume, and reagent consumption. Steam production decreased from 2.778 t/t (0% co-firing rate) to 2.358 t/t (5% co-firing rate) and 2.117 t/t (10% co-firing rate), indicating a reduction in power generation efficiency with increasing sludge co-firing rates. Leaching toxicity analysis of fly ash revealed significant reductions in the leached concentrations of Zn and Pb, while those of Hg, As, Ba, and Se showed slight increases, all remaining well below regulatory limits. This study confirms the technical feasibility of directly co-firing mechanically dewatered sludge (with a moisture content of 50% to 60%) without thermal drying. A 5% co-firing rate is identified as the optimal balance between operational economy and system efficiency.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3966-0
The development of low platinum-loading catalysts for the economically viable hydrogen evolution reaction (HER) remains challenging. Herein, a precursor dilution strategy is used to fabricate Pt nanoclusters anchored on Ni-embedded porous carbon microspheres. The approach begins with the facile synthesis of Zn/Ni-based coordination polymers (Ni-BTC-Zn) due to the isomorphic substitution of Zn2+ and Ni2+. During pyrolysis, the evaporation of zinc species results in a highly porous carbon structure with well-dispersed nickel nanoparticles. Subsequent solvothermal treatment allows for the uniform deposition of Pt nanoclusters to form the final bimetallic PtNi catalysts (PtNi-BTC-C). Among them, the optimized PtNi-BTC-C10 exhibits exceptional alkaline HER performance, requiring an overpotential of only 41 mV to achieve 10 mA cm−2 and a low Tafel slope of 31.1 mV dec−1. It also demonstrates outstanding durability with a current retention of 90.7% after 70 h, far exceeding Pt/C. Extensive characterization confirms that moderate Zn dilution optimally modulates the Ni particle size and dispersion, leading to maximized active sites and enhanced charge transfer. Combined with DFT calculations, the Pt-Ni-cluster model for PtNi-BTC-C10 possesses an optimized electronic structure with a shifted d-band center, which facilitates water dissociation and optimizes H* desorption with the most favorable energetics (0.262 eV). This work provides a fundamental understanding of precursor dilution engineering and offers a versatile pathway for designing advanced noble-metal-based bimetallic electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3967-x
Metal-halide perovskites exhibit exceptional optical gain, narrow emission linewidths, and high emission efficiency, positioning them as promising candidates for next-generation lasers. Thermal evaporation, a mature semiconductor fabrication technique, offers scalability, yet monitoring phase distribution during deposition remains challenging. This study systematically investigates and regulates thermally evaporated FAxCs0.8PbBr3 perovskite films by tuning formamidinium (FA) content to optimize phase distribution. At intermediate FA content, films achieve a balanced distribution of n=2 to n=5 quantum-well phases, facilitating ultrafast carrier transfer (<0.31 ps) and suppressing nonradiative recombination. FA+ actively incorporates as an A-site cation, promoting ordered crystallization and reducing defect densities. The optimized films exhibit a net modal gain of 1041 cm−1 and a gain lifetime of 129 ps. Benefiting from efficient internal scattering, the threshold for cavity-free random lasing is reduced to below 5 μJ/cm2 at room temperature. The low spatial coherence of random lasing enables speckle-free imaging with a speckle contrast as low as 0.011 and improved contrast-to-noise ratios across all spatial frequencies. This work provides a scalable strategy for perovskite composition-phase engineering, advancing speckle-free laser imaging systems compatible with semiconductor-grade, large-area manufacturing.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511055
To systematically investigate the spatiotemporal distribution of hydrodynamics and water quality under cascaded hydropower development in the upper Heihe River, a MIKE21-based water environment model was constructed for the mountainous reach. The model simulated the dynamic changes of total phosphorus (TP), total nitrogen (TN), and ammonia nitrogen (NH3-N) from January to August 2023. Calibration and validation against field data showed good performance: the hydrodynamic model achieved a coefficient of determination (R2) of 0.89 and a mean relative error (MRE) of 11.3%; the water quality model achieved an average R2 of 0.86 and an average MRE of 14.21%. Hydrodynamic simulations revealed average flow velocities of 1.78, 0.72, and 0.36 m·s−1 during wet, normal, and dry periods, respectively. Natural river sections exhibited high velocities up to 4.3 m·s−1, while reservoir sections had near-stagnant flow due to hydraulic structures. Water quality simulations indicated that TN and NH3-N concentrations were higher in dry and normal periods, whereas TP was higher in the wet period. Spatially, concentrations in reservoir sections exceeded those in natural sections: natural sections had TP, TN, and NH3-N concentrations of 0.07–0.10, 0.25–0.50, and 0.025–0.250 mg·L−1, respectively, while reservoir sections had 0.12–0.17, 0.60–0.80, and 0.10–0.45 mg·L−1. These findings provide scientific references for water environment management in the Heihe River and similar inland river basins.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60674-3
Conducting polymers are promising electrode materials for aqueous ion batteries and supercapacitors due to their high conductivity, environmental friendliness, and flexibility. Electropolymerization enables controlled deposition of these polymers onto conductive substrates, tuning loading, morphology, and structure. This dataset systematically compares the electrochemical energy storage performance of conducting polymers derived from monomers including 1,10-phenanthroline, 5-amino-2-naphthalenesulfonic acid, o-aminophenol, 1,5-diaminonapthalene, s-triazine, and aromatic molecules with multiple carbonyl and imino groups. Aqueous electrolytes investigated include sulfuric acid, zinc sulfate, ammonium sulfate, potassium hydroxide, and zinc trifluoromethanesulfonate solutions. Galvanostatic charge-discharge at various mass-normalized current densities was employed to evaluate specific capacities. The dataset comprises 266 MB across 490 files, providing key parameters such as specific capacity, rate capability, and cycling stability. Analysis of this data enables inference on the influence of polymer structure and electrolyte composition on charge storage. This resource serves as a reference for the rational design of high-performance conducting polymer electrodes for aqueous energy storage devices.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042103
This study investigated the spatiotemporal distribution, ecological risk, and sources of seven heavy metals (Cr, Cd, Cu, Ni, Pb, Zn, As) in surface sediments of Ranwu Lake, Xizang. Twelve samples were collected during the glacial ablation period (July 2024) and late glacial ablation period (November 2024). Concentrations were determined and analyzed using inverse distance weighting (IDW) for spatial patterns, geo-accumulation index (Igeo) and potential ecological risk index (RI) for risk assessment, and correlation analysis (CA), principal component analysis (PCA), and absolute principal component score-multiple linear regression (APCS-MLR) for source apportionment. Results showed that during glacial ablation, mean Cr, Cd, Pb, and As exceeded Xizang soil background values, while in the late ablation period only Cd, Pb, and As remained elevated. Spatial distribution varied between periods, with high concentrations in the middle and lower lake during ablation, shifting to the lower lake in the late period. Igeo and RI indicated overall low ecological risk, with Cd as the primary risk factor; mean RI values were 81.79 and 98.30 for the two periods, respectively. Source apportionment revealed that heavy metals mainly originated from natural and transportation sources, with traffic emissions being the major contributor to ecological risk. Specifically, Cr, Ni, and As were predominantly natural, Cd and Pb were mainly traffic-related, and Cu and Zn were influenced by both natural and traffic sources.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025051701
This study investigated the effects of selenium nanoparticles (SeNPs) on the growth, mycelium morphology, copper (Cu2+) removal rate, extracellular polymeric substances (EPS), and intracellular enzyme activity of Aspergillus flavus TL-F3 (A. flavus TL-F3) under Cu2+ stress. Results showed that different concentrations of Cu2+ inhibited the growth of A. flavus TL-F3. The highest Cu2+ removal rate of 56.32% was observed at a Cu2+ concentration of 50 mg·L−1. Under 50 mg·L−1 Cu2+ stress, 0.25 mg·L−1 SeNPs promoted the growth of A. flavus TL-F3, increasing its biomass by 2.71%, and significantly enhanced the fluorescence intensity of EPS, Na+/K+-ATPase activity, and decreased malondialdehyde (MDA) content, reduced superoxide dismutase (SOD) and catalase (CAT) enzyme activities. Additionally, SeNPs stimulated the glutathione (GSH-GSSG) cycle in A. flavus TL-F3, elevating glutathione peroxidase (GPX) and glutathione reductase (GR) activity by 17.2% and 23.94%, respectively, and increasing reduced glutathione (GSH) content by 18.59%, and decreasing the GSH/GSSG ratio, thereby effectively alleviating Cu2+ toxicity. Fourier transform infrared spectroscopy indicated that surface functional groups of A. flavus TL-F3, including carboxylic acid, alcohol, phenol, and phosphate/sulfate functional groups, might bind with Cu2+, enhancing its tolerance to Cu2+. This study enriches the theoretical knowledge of microorganism-heavy metal interactions and provides deeper insights into microbial heavy metal resistance mechanisms.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4060-5
Organic solar cells (OSCs) offer unique advantages for wearable electronics due to their light weight and mechanical flexibility. However, achieving both high optoelectronic performance and mechanical robustness in organic semiconductors remains challenging, compromising the efficiency and durability of stretchable OSCs. Here, we report a cross-linked conjugated polyelectrolyte (CPE)-polyoxometalate (POM) anode interlayer (AIL), PTN-POM, constructed via strong electrostatic interactions between ammonium groups and POM. The PTN-POM film exhibits an electrical conductivity of 3.30×10−3 S/m and high stretchability, significantly outperforming the classic PEDOT:PSS AIL in mechanical strength. Binary OSCs modified with PTN-POM achieve a power conversion efficiency (PCE) of 19.59%, the highest reported for OSCs using a cross-linked AIL. Notably, PTN-POM enables fabrication of water-proof OSCs that show no performance degradation after underwater storage for 42 days. Furthermore, stretchable OSCs incorporating PTN-POM demonstrate enhanced mechanical robustness, retaining 81% of initial PCE under a large tensile strain of 50%. This work significantly enhances the photovoltaic, waterproof, and mechanical properties of OSCs, advancing their potential for wearable photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4144-y
Developing efficient strategies for electrically manipulating two-dimensional magnetism at room temperature is a key challenge in contemporary spintronics. In this study, we demonstrate giant electromechanical control over the magnetism of the room-temperature van der Waals ferromagnet Fe3GaTe2 by integrating it with the ferroelectric α-In2Se3. Modest gate voltages lead to an almost complete suppression of the coercive field by 96.5%, corresponding to a remarkable peak modulation sensitivity of ~8.1 mT V−1, which stands out among existing van der Waals magnetoelectric systems. Importantly, this substantial magnetoelectric response is predominantly unaffected by voltage polarity, as both positive and negative gate voltages induce similar magnetic modulation effects. To elucidate the underlying mechanism, we tracked the voltage-induced Raman spectral changes, revealing a peak shift of 1.7 cm−1 that accurately represents an effective in-plane tensile strain of ~1.42% under an equivalent bias, demonstrating polarity independence as well. The synchronized magnetic response and strain variation unequivocally indicate that the induced tensile strain serves as the fundamental physical driver behind the magnetic modulation. Additionally, density functional theory calculations corroborate that the reduction in magnetic anisotropy induced by tensile strain results in a decrease in the coercive field. Our work establishes a novel and efficient approach for achieving voltage control of magnetism at room temperature in van der Waals multiferroic heterostructures, highlighting their significant potential for applications in ultra-low-power magnetic logic and sensing technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3970-1
Dielectric elastomer actuators (DEAs) are promising artificial muscle technologies due to their large actuation strains, high energy density, and fast response. However, their practical application is hindered by a trade-off between increasing the relative dielectric constant (εr) and decreasing the Young's modulus (Y), which limits electromechanical sensitivity (εr/Y) to below 110 MPa⁻¹. Here, we report a hetero-cross-linking strategy to fabricate a semiseparated biphasic bicontinuous dielectric elastomer (SBE) using two commercial silicone elastomers: Elastosil P7676 (mechanical phase, M-phase) and Sylgard 170 (dielectric phase, D-phase). The M-phase provides an ultralow Young's modulus (~10 kPa), while the D-phase offers a high dielectric constant (3.6). With only 10% D-phase content (SBE-1), the material achieves a record-high electromechanical sensitivity of 360 MPa⁻¹. Under an electric field of 35 V μm⁻¹ without prestretching, SBE-1 exhibits a 90% area strain, significantly outperforming pure phases and previously reported DEAs. The interpenetrating phase structure also enhances breakdown strength. SBE-based artificial muscles demonstrate large displacement at high frequencies, achieving a power density of 2250 W kg⁻¹ at resonance (>200 Hz), surpassing natural muscle and prior DEA artificial muscles. A human-like robotic arm with one rotational joint and four pure-shear SBE-based artificial muscles was developed, capable of extending and bending actions. This work provides a versatile strategy for high-performance DEAs, advancing soft robotics applications.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60668-8
A series of Co-based molecular sieve catalysts with varying Si/Al ratios was synthesized via impregnation. Microstructural properties of Co active sites were characterized by XRD, TEM, Raman, H2-TPR, Py-FTIR, and XPS. Results indicate that surface Co species predominantly exist as CoOx nanoclusters and isolated Co2+, with the latter exhibiting superior N2O decomposition activity. Decreasing the Si/Al ratio of the MFI zeolite promotes the formation of isolated Co2+ active sites, thereby enhancing catalytic performance. Compared to Co/S-1 (pure silica support), the Co/HZ60 catalyst (low Si/Al ratio ZSM-5) lowers the temperature for complete N2O decomposition by 80 °C and demonstrates excellent resistance to O2 and NO. The strong interaction between the zeolite framework and Co2+ inhibits oxidation to Co3+, improving N2O adsorption and activation. This work provides a rational design strategy for efficient and stable Co-based catalysts for N2O abatement in industrial tail gases.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4126-0
Flexible X-ray detectors are constrained by the difficulty of producing semiconductor films that simultaneously exhibit uniform morphology, high crystallinity, and mechanical robustness. Here, we introduce a hydrogen-bond engineered supramolecular (HBES) strategy to overcome these limitations in supramolecular bismuth halide clusters (PDBiI5). By incorporating polyacrylic acid (PAA), a dynamic supramolecular network is formed that suppresses the coffee-ring effect during ultrasonic spray-coating via increased solution viscosity and controlled kinetic balance between solvent evaporation and solute diffusion. The HBES approach also modulates crystallization kinetics, extending crystal growth time from 23 to 41 s, yielding densely packed films with enhanced crystallinity and reduced defect states. These improvements lead to superior charge transport: a hole mobility of 2.16 cm2 V−1 s−1 and a mobility-lifetime product of 9.1 × 10−4 cm2 V−1. The resulting X-ray detectors achieve a record sensitivity of 19,009 μC Gyair−1 cm−2 and an ultralow detection limit of 3.35 nGyair s−1, with excellent operational and environmental stability. Leveraging the mechanical robustness from the supramolecular network, we demonstrate the first direct-type flexible X-ray imager, retaining 85% performance after 1000 bending cycles. This imager overcomes geometric distortion and vignetting, maintaining 85% edge photocurrent versus 58% for rigid detectors, enabling clear imaging of curved objects. This work establishes a versatile supramolecular engineering paradigm for high-performance flexible X-ray detection and imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4131-3
p-n heterojunction solar-blind photodetectors based on p-type materials and n-type Ga2O3 have attracted significant attention in optoelectronics due to their inherent low dark current and self-powered operation. Organic-inorganic hybrid heterojunctions integrating p-type organic materials with n-type Ga2O3 offer a promising solution to overcome lattice mismatch, enabling device performance breakthroughs. In this work, Ga2O3 thin films were treated via a supercritical fluid (SC) technique, which significantly reduced defect state density while improving crystallinity and surface uniformity, laying a foundation for heterojunction interface optimization. Simultaneously, a self-assembled monolayer (SAM) was introduced at the organic-inorganic heterojunction interface. The high-quality Ga2O3 surface engineered via SC treatment facilitated efficient, oriented self-assembly of SAM molecules, enabling precise modulation of interfacial energy band alignment and promoting separation and transport dynamics of photogenerated carriers. Benefiting from synergistic SC modification and SAM functionalization, the fabricated solar-blind photodetector achieved a highest responsivity of 111.7 mA/W and a specific detectivity of 1.02 × 10^11 Jones under zero bias (self-powered mode) and weak 254 nm light with an intensity of 5 μW/cm2. These results demonstrate a viable route to high-performance, self-powered solar-blind photodetectors through interface engineering.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3643-8
Inverted perovskite solar cells (PSCs) suffer from defect-mediated nonradiative recombination and inefficient charge extraction, particularly at the buried interface and grain boundaries (GBs), which limit power conversion efficiency (PCE) and operational stability. This study introduces a multifunctional phosphonic acid molecule, (2-(3,6-bis(trifluoromethoxy)-9H-carbazol-9-yl)ethyl)phosphonic acid (M28), as an additive in the perovskite precursor solution. M28 spontaneously segregates toward the buried interface and GBs, fulfilling three roles: (1) slowing crystallization to enlarge grains and improve film quality, (2) passivating defects to suppress charge recombination, and (3) inducing p-type doping to create an extra electric field that promotes hole transport. Devices incorporating M28 achieve a champion PCE of 25.96% and retain 80% of initial efficiency after 1500 h of maximum power point tracking. This work demonstrates the efficacy of multifunctional phosphonic acid additives in addressing buried-interface and GB defects, offering a viable route to high-performance, stable inverted PSCs.