SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4238-2
Infrared nonlinear optical (IR NLO) materials are critical for laser frequency conversion, yet their performance is often constrained by a trade-off between second harmonic generation (SHG) efficiency and laser-induced damage threshold (LIDT). Here, we report a new ternary diamond-like compound, AlGaS3, which successfully balances these competing demands. AlGaS3 crystallizes in a noncentrosymmetric structure composed of wide HOMO-LUMO gap [AlS4] tetrahedra and NLO-active [GaS4] tetrahedra. The compound exhibits a wide experimental optical band gap of approximately 3.38 eV, which is significantly larger than that of the benchmark AgGaS2 (AGS, ~2.70 eV). This wide band gap contributes to a high laser-induced damage threshold (LIDT) of approximately 6.0 times that of AGS, as determined by powder-based measurements. Notably, AlGaS3 also demonstrates a phase-matching SHG response of approximately 0.5 times that of AGS at a fundamental wavelength of 2.09 μm, with particle size-dependent behavior confirming phase-matchability. The combination of wide band gap, high LIDT, and moderate SHG response positions AlGaS3 as a promising candidate for high-power IR NLO applications. This work provides a viable strategy for designing IR NLO materials with enhanced laser damage resistance by incorporating wide-gap tetrahedral units.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4315-2
High-temperature X-ray imaging demands scintillators with high crystallinity, efficient scintillation, and robust thermal stability, yet suitable materials remain scarce. Here, we report an ultra-high-crystallinity transparent glass-ceramic (GC) scintillator strategically designed via controllable heat-treatment-induced crystallization. A sequential precipitation method is employed, where cubic CaF2 nanocrystals initially form, subsequently promoting heterogeneous nucleation and growth of hexagonal BaAl2Si2O8. Intrinsic nanoscale phase separation into F-rich and O-rich domains significantly reduces atomic diffusion distances, yielding an unprecedented crystallinity of up to 97.6%. Notably, defect traps (oxygen vacancy defects, likely located within the lattice or at crystalline/amorphous interfaces) enable efficient carrier capture and thermally stimulated release, contributing to remarkable resistance to thermal quenching. Consequently, the GC scintillator maintains 90.6% of its integrated X-ray excited luminescence (XEL) intensity at 300 °C, with the integrated XEL intensity reaching 94.2% of commercial Bi4Ge3O12 (BGO) at room temperature. This enables stable high-temperature X-ray imaging with a spatial resolution of ~10.4 lp mm−1 up to 225 °C. This work provides a versatile pathway for developing high-sensitivity scintillators for extreme-environment X-ray imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4217-y
Rational design and construction of effective photocatalysts is a promising way for green and sustainable chemistry, but still a great challenge. Herein, taking triphenylamine-containing aldehydes as reactants, two covalent triazine frameworks (CTFs), tris(4-formylphenyl)amine (TPA)-CTF and tris(4-formylbiphenyl)amine (TBPA)-CTF, were rationally constructed. The strong electron donor property of the triphenylamine moieties derived from the initial reactants and the strong electron acceptor nature of the in-situ formed built-in triazine rings in CTFs endowed these robust triphenylamine-based CTFs with donor-acceptor (D-A) or donor-π-acceptor (D-π-A) structure features. Photocatalytic experiments revealed that, compared with the controlled phenyl analogue CTF, 1,3,5-tri(p-formylphenyl)benzene (TFPB)-CTF, both of the triphenylamine-based CTFs exhibited superior photocatalytic activity not only in photocatalytic hydrogen peroxide generation, but also in photocatalytic aerobic oxidations of diverse organic substrates. Theoretical studies further confirmed that their enhanced photocatalytic performance should be attributed to their unique D-A or D-π-A features in the constructed triphenylamine-based CTFs. This work successfully demonstrated that rational selection of reactants containing electron donor moieties to construct CTFs should be a reliable way for the construction of effective photocatalysts for photocatalytic oxidation reactions.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3635-6
Oxygen anionic redox (OAR) is pivotal for achieving extra lithium storage in high-energy-density Li-ion batteries, yet its activation and stabilization remain challenging. Traditionally, OAR is studied in crystalline layered oxides with ordered frameworks and transition metal (TM)-centered octahedral coordination, where the Li-O-Li configuration is considered a prerequisite for creating unhybridized O 2p states. However, recent findings indicate that the presence of unhybridized O 2p states, rather than a specific configuration, is essential for oxygen activation. This study reports a novel OAR mechanism in an amorphous Li-V-O-F cathode, operating at a moderate voltage of 4.1 V, distinct from conventional Li-O-Li configurations. The cathode, initially crystalline LiVO2.98F0.02 (F2), undergoes amorphization after the first charge-discharge cycle, as evidenced by ex situ XRD, HRTEM, and EXAFS. Resonant inelastic X-ray scattering (RIXS) and X-ray absorption spectroscopy (XAS) reveal that the initial charge involves O-O formal redox without oxidized oxygen features, indicating electron holes are accommodated via O-O interactions. Reversible OAR activity emerges in the second cycle, confirming O-O dimerization in the amorphous phase. Ab initio molecular dynamics (AIMD) simulations further elucidate the mechanism. This work challenges the conventional Li-O-Li paradigm and opens new avenues for designing high-capacity cathode materials through amorphization and tetrahedral coordination.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3598-1
Embedding a dielectric layer between as-synthesized graphene nanoribbons (GNRs) and metal surfaces represents a powerful strategy to achieve electronic decoupling, thereby enabling the extraction of these ribbons' intrinsic electrical properties. Although several reports have documented dielectric intercalation between GNRs and metal substrates, studies on Ag(111) substrates are limited. Here, we demonstrate a semiconducting AgTe monolayer intercalation method to achieve electronic decoupling between as-synthesized GNRs and an Ag(111) substrate. Using low-temperature scanning tunneling microscopy, we directly observed the AgTe intercalation process at the GNR/Ag(111) interface. By combining scanning tunneling spectroscopy and density functional theory calculations, we elucidate the critical role of AgTe monolayer intercalation in reducing the interaction between as-synthesized GNRs and the Ag(111) substrate and observe the near-intrinsic electrical properties of the GNRs. Our findings offer a practical and effective strategy for intercalating AgTe monolayers between carbon-based nanomaterials and Ag(111) substrates, facilitating the unambiguous characterization of the near-intrinsic electronic properties of these materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3757-2
β-Ga2O3 is a promising candidate for solar-blind ultraviolet photodetection owing to its suitable bandgap of approximately 4.9 eV, excellent photoresponse characteristics, and high stability. However, the lack of a sufficient driving force within the material leads to extensive bulk charge recombination, limiting its photocurrent and thus posing significant challenges in designing high-performance Ga2O3-based photodetection. In this study, we propose a gradient doping strategy to achieve a Sn-doping concentration gradient along the β-Ga2O3 film thickness. By combining sol–gel synthesis with rapid thermal annealing, a spatially graded band structure with a full-space built-in electric field is constructed, which increases the width of band bending over a large region and is crucial for significantly enhancing carrier separation and transport in the bulk. The resulting gradient Sn-doped β-Ga2O3 enables exceptional photoelectric performance without an external bias under 254 nm irradiation, including a superior responsivity of 66.88 mA W−1, a high detectivity of 8.12 × 10^11 Jones, and a fast rise/decay time of 79/65 ms, outstanding most existing similar reported photoelectrochemical (PEC) type optoelectronic devices. Additionally, the device exhibits excellent long-term stability and enables high-resolution underwater ultraviolet imaging. This study demonstrates that the gradient doping strategy provides a feasible approach for enhancing the PEC performance of β-Ga2O3 photoelectrodes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3805-1
The sluggish kinetics of oxygen reduction and evolution reactions (ORR/OER) at the air electrode impede the practical deployment of fiber zinc-air batteries (FZABs) for wearable electronics. Conventional bifunctional catalysts suffer from an inherent activity trade-off due to the distinct mechanisms of ORR and OER. Here, we propose a spatial decoupling strategy to overcome this limitation by engineering isolated Fe single atoms and Fe–Ir dual-atom pairs on a nitrogen-doped carbon matrix (Fe/FeIr-NC). In this architecture, Fe single atoms serve as ORR centers, while Fe–Ir pairs with tunable spacing are tailored for OER, enabling complete functional separation and independent optimization. The catalyst exhibits an ORR half-wave potential of 0.91 V and an OER overpotential of 250 mV at 10 mA cm−2, yielding a record-low bifunctional gap (ΔE = 0.57 V) that outperforms all reported single- and dual-atom catalysts. A flexible fiber zinc-air battery based on this catalyst delivers a peak power density of 3920 W kg−1, along with a 1.4-fold increase in energy efficiency and a 2.6-fold extension in cycle life compared to the commercial Pt/C + IrO2 benchmark. This work not only breaks the traditional activity trade-off in bifunctional catalysis but also offers a promising route toward high-performance power sources for wearable electronics.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507043
Municipal sludge with high moisture content and strong viscosity tends to form a dense crust during conventional rotary drum drying, reducing heat and mass transfer efficiency and prolonging drying time. This study proposes a thermal steel ball-enhanced rotary drum drying method that introduces high heat capacity, high thermal conductivity steel balls to achieve synergistic contact heat conduction and mechanical disturbance. An evaluation system incorporating dimensionless moisture ratio (MR), drying rate (DR), characteristic drying time (tdry), effective moisture diffusivity (Deff), and volumetric evaporation intensity (U) was established. Results show that compared with conventional drying, steel ball-enhanced drying increased maximum drying rate (DRmax) by 22.59%–41.19%, U by 38.06%–93.43%, and shortened tdry by 27.56%–48.30%, with more pronounced advantages under high load conditions. Deff was significantly higher throughout the process, with maximum increase up to 48.30%, indicating that ball rolling and collision effectively disrupt the crust and promote moisture migration. Mechanistic analysis reveals that the performance enhancement arises from the dual action of thermal-mechanical coupling and mechanical disturbance, which enhances local heat flux via contact conduction and dynamically renews the drying interface, shortening diffusion paths. This study elucidates the heat and mass transfer mechanisms of thermal steel ball-enhanced sludge drying, providing theoretical support and technical reference for efficient sludge volume reduction and dryer design optimization.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010402
Vegetable consumption is a well-established pathway for human exposure to per- and polyfluoroalkyl substances (PFAS). These contaminants are absorbed by vegetables through uptake from soil and irrigation water, leading to bioaccumulation within plant tissues and posing potential risks to human health. Therefore, monitoring PFAS concentrations in vegetables is critical for assessing dietary exposure and associated health risks. In this study, a solid-phase extraction (SPE) followed by ultra-high performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) method was developed for the determination of 24 PFAS compounds in leafy vegetables, including Shanghai Bok Choy, Cabbage, and Water Spinach. The analytical method, incorporating organic solvent extraction followed by SPE cleanup, was optimized with respect to both extraction solvent and SPE sorbent. Alkaline methanol was used as the extraction solvent, and PFAS in vegetables were extracted via vortex-assisted extraction. Tandem mass spectrometry was used for detection in multiple reaction monitoring mode, and quantification was performed by internal standard method. Under optimized conditions, at a spiking level of 2 ng, recoveries ranged from 50.0% to 120.8% with relative standard deviations (RSD) between 1.0% and 26%. Calibration curves showed good linearity with correlation coefficients (r) greater than 0.99. Limits of detection (LOD, S/N=3) were between 0.002 and 0.103 ng·g−1, and limits of quantification (LOQ, S/N=10) were between 0.007 and 0.343 ng·g−1. The method was applied to real samples, detecting 20 PFAS, with 10 compounds showing 100% detection frequency. Total PFAS concentrations ranged from 2.92 to 6.83 ng·g−1 dry weight (dw). Perfluorobutanoic acid (PFBA) was the dominant contaminant, with concentrations from 1.18 to 3.74 ng·g−1 dw. The method demonstrates good sensitivity and accuracy, effectively identifying and quantifying multiple PFAS, thus providing reliable technical support for monitoring PFAS in vegetables.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024100805
A fluorescent metal-organic framework (MOF), PCN-128, was synthesized via a solvothermal method using zirconium tetrachloride (ZrCl4) as the metal source and tetrakis[4-(4'-carboxyphenyl)phenyl]ethylene (H4ETTC) as the organic linker. The resulting material exhibited regular morphology, high crystallinity, strong luminescence, and good stability. PCN-128 was employed as a fluorescent probe for the trace detection of malachite green (MG), a banned veterinary drug, in aquaculture water and freshwater fish tissue. The probe demonstrated exceptional selectivity toward MG among 13 veterinary drugs and robust anti-interference performance against 16 anions, 16 cations, and 12 additional veterinary drugs. The method achieved a broad linear detection range from 0.0 to 7.0 μmol·L−1 with a limit of detection (LOD) of 2.73 nmol·L−1. Spike-and-recovery experiments in three aquaculture water samples and one freshwater fish sample yielded recoveries between 89.80% and 113.7%, with relative standard deviations (RSD) not exceeding 2.59%. These results confirm that the developed method is accurate, reliable, and suitable for routine monitoring of MG residues in aquaculture water and aquatic products, addressing a critical gap in food safety surveillance.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010608
This study investigated the occurrence and distribution of 27 per- and polyfluoroalkyl substances (PFAS) in surface water and sediment of the Fuchun River, a tributary of the Qiantang River Basin. Surface water samples were analyzed using ultra-performance liquid chromatography coupled with high-resolution mass spectrometry. Total PFAS concentrations (∑PFAS) in surface water ranged from 30.04 to 105.26 ng/L, with mean and median values of 59.64 ng/L and 51.43 ng/L, respectively. The dominant compounds were perfluorooctanoic acid (PFOA), hexafluoropropylene oxide dimer acid (GenX), and perfluorobutanoic acid (PFBA). Concentrations generally decreased from upstream to downstream, consistent with previous studies. Notably, GenX levels were significantly elevated compared to earlier reports. In sediment, ∑PFAS concentrations ranged from not detected (ND) to 0.59 ng/g dry weight, with mean and median values of 0.14 ng/g and 0.11 ng/g, respectively. PFOA and perfluorooctanesulfonic acid (PFOS) were the primary sediment contaminants. Source apportionment indicated that industrial wastewater discharge and sewage treatment plant effluents were the main sources of PFAS in the river. Risk assessment using risk quotients suggested low ecological risks to aquatic organisms for most detected PFAS. However, the presence of short-chain and novel PFAS warrants further investigation due to potential unknown risks.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012302
Phosphorus (P) loss from paddy fields contributes to eutrophication in Chaohu Lake. This study evaluated the effects of novel fertilizers and P reduction on P loss and rice yield. Seven treatments were established: no P (CK), rice-specific fertilizer (ZYF), slow-release blended fertilizer (SRF), Xinjutian compound fertilizer (XJT), enhanced loss-controlled fertilizer (CRF), CRF with 10% P reduction (CRF-10P%), and CRF with 30% P reduction (CRF-30P%). Results showed that novel fertilizers and P reduction significantly reduced concentrations of total phosphorus (TP), dissolved phosphorus (DP), and particulate phosphorus (PP) in surface water and leachate. The first 5 days after basal fertilization and heavy rainfall were high-risk periods for P loss. Rainfall increased TP concentrations by 417.74%–432.86% and 94.85%–351.35% in surface water and leachate, respectively; DP increased by 120.80%–322.44%, and PP by 280.66%–501.77% and 80.23%–297.55%. Compared with ZYF, SRF, XJT, and CRF reduced TP loss by 15.43%–33.95%, with SRF showing the lowest loss. Under P reduction, CRF-10P% and CRF-30P% reduced TP loss by 31.48% and 37.04%, respectively, with CRF-30P% achieving the lowest loss. Notably, CRF-10P% increased rice yield by 22.37% relative to ZYF, indicating that moderate P reduction with enhanced loss-controlled fertilizer can maintain or increase yield while reducing environmental risk. The study concludes that CRF-10P% offers a promising strategy for sustainable rice production in the Chaohu Lake watershed.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025091205
This study analyzes the spatiotemporal variation characteristics and driving mechanisms of PM2.5, PM10, SO2, NO2, O3, and CO in the Kuytun-Dushanzi-Wusu (Kui-Du-Wu) region of Xinjiang, based on monitoring data from 2018 to 2024. Results indicate that urban sites (e.g., Kuytun Laoganju Station) are influenced by traffic emissions, leading to elevated PM2.5 and NO2 concentrations. Dushanzi District, with petrochemical industry emissions, exhibits notable SO2 and O3 pollution. Agricultural areas (e.g., Kuytun Huaxin Tomato Company) show significant PM10 and CO levels affected by dust and diesel machinery. Over the study period, PM2.5, PM10, NO2, and CO concentrations generally declined at annual rates of 1.5–4.0 μg·m−3·a−1, reflecting the effectiveness of coal substitution, industrial upgrades, and vehicle emission controls. Conversely, O3 concentrations increased consistently at rates of 1.3–3.2 μg·m−3·a−1, highlighting shortcomings in volatile organic compound (VOCs) control. Seasonal patterns show PM and CO peaking in winter due to heating combustion and temperature inversions, and reaching minima in summer due to enhanced diffusion and precipitation. O3 peaks in summer driven by photochemical reactions, contrasting with NO2 winter highs from heating and industrial activities. The findings underscore the need for coordinated control of VOCs and NOx, optimized dust management, and differentiated emission controls for industrial, traffic, and agricultural sources.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012101
Continuous monitoring of 114 volatile organic compounds (VOCs) was conducted in the urban atmosphere of Haigang District, Qinhuangdao City, from September 2022 to February 2023. The volume concentrations of total VOCs were 42.72×10⁻⁹ in autumn and 25.15×10⁻⁹ in winter. The predominant species were isopentane, ethane, and ethylene. Ozone formation potential (OFP) analysis indicated that alkanes and alkenes dominated the atmospheric pollution during autumn and winter, with isopentane and ethylene being the largest contributors. Aromatic hydrocarbons contributed up to 85.00% of the secondary organic aerosol formation potential (SOAFP), with benzene as the primary species. Positive matrix factorization (PMF) identified four major sources: technological processes and oil/gas volatilization (35.57%), combustion and petrochemical emissions, motor vehicle emissions, and regional background sources. The results underscore the need for targeted control of VOCs from industrial and vehicular sources to mitigate secondary pollution in coastal cities.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3804-7
Supramolecular helical architectures hold promise for enantioselective catalysis, yet the influence of screw pitch on catalytic performance remains underexplored. Here, we report the construction of right-/left-handed helical nanoribbons (P/M-DAIPA) based on 5-aminoisophthalic acid dimer (DAIPA). Through an alcohol-mediated self-assembly strategy, the average screw pitch was tuned from 360 to 3152 nm. Mechanistic studies revealed that hydrogen-bonding interactions between DAIPA, modulated by alcohol identity and alcohol/water ratios, dictate helical morphology and pitch. Encapsulation of Fe3O4 nanoparticles yielded P-DAIPA-Fe3O4 and M-DAIPA-Fe3O4 nanozymes, which exhibited higher catalytic efficiency toward S-3,4-dihydroxyphenylalanine (DOPA) and R-DOPA, respectively. Notably, catalytic enantioselectivity inversely correlated with screw pitch, achieving selectivity factors from 1.52 to 2.01. Experimental evidence demonstrated that shorter screw pitch enhances adsorption enantioselectivity of R/S-DOPA on the nanozymes, providing mechanistic insight into pitch-dependent asymmetric catalysis. This work deciphers solvent-driven control of supramolecular screw pitch and establishes a framework for engineering chiral nanozymes with tunable enantioselectivity, advancing enantioselective synthesis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3993-y
Conventional liquid-phase in-situ synthesis of Cu-TiB2 composites often suffers from coarse and non-uniformly distributed reinforcements, stemming from insufficient understanding and control over the in-situ nucleation and growth mechanisms of TiB2 particles. This study introduces a novel melt dispersion-turbulent mixing (MDTM) in-situ reaction technology to fabricate high-performance Cu-TiB2 composites. The MDTM strategy synergistically refines reaction micro-regions by reducing the initial melt droplet size via melt dispersion while enhancing solute convection via turbulence, promoting high-density nucleation and refinement of TiB2 particles. Based on turbulence characteristics and in-situ reaction kinetics, we optimized the melt disperser parameters and established a quantitative model linking particle size to disperser rotation speed and reactant solute concentration. It was found that disperser rotation speed governs three distinct nucleation and growth mechanisms for TiB2 particles. Low-density nucleation at low disperser rotation speeds (0–50 r/min) leads to coarse TiB2 particles. At medium rotation speeds (100–150 r/min), the refinement of micro-regions in the dual-melt reaction achieves high-density TiB2 nucleation. Conversely, at high rotation speeds (150–200 r/min), intense turbulence weakens the nucleation driving force and induces TiB2 particle coarsening. This work provides new insights into liquid-phase in-situ reaction mechanisms and offers a novel, controllable route for fabricating high-performance micro/nano particle-reinforced metal matrix composites.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025112603
The cycloaddition of carbon dioxide (CO2) to epoxides (CCE) is a 100% atom-economical transformation yielding cyclic carbonates, which are valuable chemical products. This reaction valorizes CO2 as a carbon feedstock, mitigating the greenhouse effect and aligning with carbon neutrality goals. Conventional covalent organic framework (COF) catalysts often require co-catalysts to achieve high efficiency. To address this, we designed and prepared a series of ionic COFs, denoted EB-BT(nOH), that simultaneously incorporate acid (hydroxyl), base (nitrogen), and nucleophilic bromide (Br−) functionalities. These materials efficiently catalyze the CCE reaction without any co-catalyst. Among them, EB-BT(OH) exhibited the highest catalytic activity, achieving a 99% yield of the target product at 120 °C and 2.0 MPa CO2 pressure. By systematically varying the hydroxyl content in the COF backbone, we investigated the critical role of hydrogen bond donors (HBDs) in the CCE reaction. This work provides new design principles for COF-based catalysts for CCE, eliminating the need for co-catalysts and enhancing process sustainability.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025021401
This study investigated the occurrence, distribution, sources, and ecological risks of 19 organophosphate triesters (OPEs) and 8 diesters (di-OPEs) in surface water and sediments from the Hangzhou section of the Qiantang River. Samples were analyzed using liquid chromatography-high resolution mass spectrometry. Concentrations of ΣOPEs in water ranged from 31.5 to 98.9 ng/L, and in sediments from 10.8 to 341 ng/g dry weight (dw). Σdi-OPEs ranged from 2.19 to 104 ng/L in water and 0.437 to 106 ng/g dw in sediments, indicating moderate to low contamination. TCIPP and TCEP dominated OPEs in water, while TEHP was the predominant OPE in sediments. DBP was the major di-OPE in water, and DPHP in sediments. Source apportionment via correlation and principal component analysis identified industrial production and human activities, including household, tire, plastic manufacturing, and agricultural practices, as primary sources. Ecological risk assessment revealed negligible risks for most OPEs in water, but notable risks in sediments: TEHP and EHDPP posed risks to crustaceans, and TPHP to algae. Moreover, combined toxicity at multiple sediment sampling sites raised concern, warranting further attention.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606010
Dissolved oxygen (DO) is a critical factor controlling endogenous phosphorus (P) migration in eutrophic waters. Existing oxygenation technologies suffer from high energy consumption and sediment disturbance, necessitating low-disturbance, pH-stable strategies that avoid additional nitrogen and P loads. This study evaluated an oxygen-loaded porous material (OLPM) for inhibiting sediment P release using laboratory microcosms with natural eutrophic water samples. DO microprofiles across the sediment-water interface (SWI) were measured with microelectrodes; diffusive gradients in thin films (DGT) resolved Fe, S, and P distributions; and sequential extraction quantified sediment P fractions. Results showed that OLPM coverage increased surface sediment DO concentration by 6.58-fold and DO penetration depth by 1.33-fold (16.8 mm). Overlying water total phosphorus (TP) decreased by 93.79%, and sediment interstitial phosphate (PO4-P) decreased by up to 45.75%. The SWI TP exchange flux reversed from +0.0068 mg/(m2·d) to -0.014 mg/(m2·d), shifting the system from a P source to a P sink. Sediment P fractionation revealed a 5.22% increase in stable Res-P and a 4.48% decrease in labile NaHCO3-P. Mechanistically, OLPM enhanced iron oxidation (Fe2+ reduced by 59.62%) and suppressed sulfate reduction (S2- homogenized at low levels), promoting P immobilization via Fe-S coupling. The material effectively inhibits endogenous P release through interfacial DO regulation without altering pH, offering a promising approach for eutrophication management.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3799-4
Li-rich layered oxides (LLOs) xLi2MnO3·(1−x)LiTMO2 (0 < x < 1, TM = Mn, Ni, Co, etc.) are promising high-energy cathode materials for lithium-ion batteries, capable of achieving energy densities up to 1000 Wh kg−1. However, their practical application is hindered by limited cycle life and voltage decay, primarily stemming from structural instability of Li2MnO3 and LiTMO2 domains during cycling, which manifests as transition metal cation migration, oxygen release, and TM dissolution. This review establishes a comprehensive design and modification scheme based on the fundamental structural unit of LLOs: the LiMn6 hexatomic-ring. In this unit, each Li atom in the TM layer is surrounded by six Mn atoms, forming a π-type hybridization between Mn 3d(t2g) and O 2p orbitals, creating an intact π-bond ring that acts as a distributed redox center. Ordering these functional units into specific spatial configurations can enhance capacity, voltage, and structural stability. However, substituting Mn with other elements breaks the symmetry of the π-bond ring, altering redox behavior and reversibility. The spatial arrangement of LiMn6 rings, representing the arrangement of π-bond rings, is critical for redox activity. In Li2MnO3, the typical honeycomb superstructure of LiMn6 rings is discussed. This review highlights the importance of functional unit ordering in material design, drawing parallels from other systems, and proposes a systematic approach to engineer LLOs for improved electrochemical performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3894-9
Photocatalytic production of hydrogen peroxide (H2O2) using water and O2 offers an economical, environmentally friendly, and sustainable route for H2O2 synthesis. However, current photocatalytic systems suffer from poor charge carrier transport, narrow light absorption, and insufficient active sites, leading to unsatisfactory H2O2 production efficiency. In this study, a CoS/ZnIn2S4 (ZIS) composite was constructed by in-situ growing CoS nanoclusters on ZIS via a solvothermal method for photocatalytic H2O2 production. The integration of CoS with ZIS broadened the light absorption spectrum. The optimized CoS/ZIS-3 composite exhibited an exceptional H2O2 production rate of 2693.39 μmol g−1 h−1 under visible light in isopropanol, surpassing pristine ZIS and CoS by factors of 6.54 and 18.08, respectively. The S-scheme heterojunction and built-in electric field synergistically enhanced the separation and transportation of photogenerated charge carriers, thereby improving photocatalytic efficiency. The H2O2 synthesis mechanism involves dual-channel oxygen reduction and water oxidation reactions mediated by CoS/ZIS. The produced H2O2 effectively degraded organic pollutants and inhibited the growth of E. coli. This study presents a promising green strategy for enhancing ZIS-based photocatalysts through constructing S-scheme heterojunctions for efficient H2O2 synthesis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4148-3
Biological ion channels exhibit multistate transport behavior beyond simple binary open-closed conformations, enabling dynamic control of neural signaling and transmembrane substance transport. Inspired by this, we synthesized a triphenylamine-ketone donor-acceptor (D-A) type poly(aryl amine-ketone) with multiple redox sites, allowing continuously tunable electrochemical states via hierarchical electron transfer. Combining this polymer with two-dimensional conductive MXene, we constructed a biomimetic nanofluidic transistor. Through side-group tuning to optimize redox matching, the polymer undergoes reversible conformation switching via intramolecular charge transfer at voltages below 1 V. The field-driven conformational changes induce electrostatic attraction, promoting reversible contraction of MXene interlayers. Synergistic coupling of interlayer spacing variation and dynamic interfacial charge rearrangement enables precise hierarchical control of ion flux. The device achieves three switchable ion transport states—closed, partially open, and fully open—with an ion switching ratio of 10 and outstanding cycling stability. Furthermore, synaptic plasticity features emulate fundamental attributes of biological signaling, providing a foundation for bioinspired neuromorphic devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3866-y
Precise measurement of flight parameters—including angle of attack (AOA), angle of sideslip (AOS), and airspeed—is critical for stabilized control of unmanned aerial vehicles (UAVs) in complex aerodynamic environments. Conventional rigid sensors fail to conform to curved leading edges, disrupting local flow and degrading aerodynamic performance, and are ill-suited for UAV miniaturization. Emerging flexible sensing technologies using hot-film, piezoresistive, or capacitive transduction offer potential solutions. This work presents a flexible pressure-velocity sensing patch developed by Professor Jiang's team at Beihang University. The patch integrates a capacitive differential pressure sensor array and a vector flow sensor, fabricated via a multi-layer polyimide bonding process. The capacitive differential pressure sensor features dual-layer chambers, achieving a resolution of 12 mPa within 0–1 Pa, superior to traditional single-layer designs. The vector flow sensor operates on the calorimetric principle, using a micro-heater and thermistor array to characterize flow velocity and direction. A novel pressure-velocity fusion (PVF) algorithm introduces spanwise velocity (Vz) to decouple AOA and AOS, reducing computational complexity compared to classic three-sensor algorithms. Computational fluid dynamics (CFD) simulations validated the algorithm's reliability under wind tunnel conditions. The sensing patch enables simultaneous measurement of multiple flight parameters with high precision and low computational cost, addressing the limitations of rigid sensors and advancing UAV aerodynamic sensing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3950-x
Photocatalytic oxygen reduction reaction (ORR) for hydrogen peroxide (H2O2) production via the two-electron pathway offers an environmentally friendly oxidant and a clean fuel. However, challenges exist in optimal oxygen (O2) adsorption capacities and maintaining O–O bond during O2 activation. Herein, we present a zinc single-atom catalyst (Zn/VN-CN) incorporating nitrogen vacancies (VN), designed to modulate the electronic structure of the photocatalyst, leading to optimized O2 adsorption energy and a remarkable enhancement in H2O2 yield. Benefiting from the synergistic effect between nitrogen vacancies and Zn single atoms, the optimized Zn/VN-CN catalyst exhibits a photocatalytic H2O2 production rate of 2.399 mmol g−1 h−1 under visible-light irradiation, representing a 12-fold enhancement compared to pristine g-C3N4 (CN), along with a high H2O2 selectivity of 87.4%. Combined experimental and theoretical studies indicate that the Zn-N3 sites act as highly active reaction centers, while nitrogen vacancies increase the charge density and downshift the d-band center of the Zn sites, thereby moderating O2 adsorption strength, lowering the activation energy barrier for the formation of *H2O2, and further converting it to H2O2. This work proposes an effective strategy for tuning O2 adsorption behavior to achieve highly selective and active photocatalytic H2O2 production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3825-x
Polymer-based dielectric materials with high energy density and thermal stability are critical for modern electric/electronic industries. Polyimide (PI) based materials are promising due to their high temperature resistance and chemical inertness, yet their inherently low dielectric constant and limited charge-discharge energy density restrict applications in film capacitors. While incorporating ferroelectric or conductive fillers can enhance dielectric performance, batch-to-batch inconsistency and physical deterioration remain problematic. This study focuses on molecular structure design and modulation, preparing hyperbranched polyimides with different dianhydride monomers and branching degrees. The effects of chain packing density with polar groups on dielectric and energy storage performances were systematically investigated via experimentation and molecular simulation. Results demonstrate a significant correlation between monomers' electrical distribution and packing density in polymer systems. Molecular simulation further elucidated the underlying mechanism. This work establishes a foundation for designing polymer-based dielectric materials with high dielectric and energy storage performances at the molecular level.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511050
Municipal solid waste (MSW) management in Inner Mongolia has long relied on landfilling, facing land scarcity and leachate management challenges. This study addresses the region's dry, cold climate, high proportion of agricultural and livestock waste, fluctuating moisture content, and weak leachate treatment capacity. An engineering optimization was implemented on an 80 t·d−1 vertical rotary gasification-incineration system featuring a dual-combustion-chamber design (primary chamber for medium-temperature pyrolysis-gasification at 550–650 °C and secondary chamber for high-temperature oxidation above 900 °C), coupled with in-situ leachate recirculation. Field measurements showed improved processing capacity and continuous operation stability. Under the project's leachate yield, in-situ recirculation achieved on-site disposal without significant adverse effects on gasification-incineration conditions, providing buffering against moisture fluctuations. During the monitoring period, major gaseous pollutant emissions remained below current national standards. The results provide engineering references for the co-processing and stable operation of small-scale county-level MSW treatment facilities.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4097-3
The on-demand patterning of two-dimensional transition metal dichalcogenides (TMDs) with tailored edges is critical for electronic and optoelectronic applications but remains technically challenging. Here, we report a stress-guided anisotropic etching strategy for producing large-area, well-ordered MoS2 nanostructures, including nano-ribbons and nano-squares, without templates. By applying uniaxial cumulative stress followed by selective thermal etching, MoS2 monolayers are statistically etched into ribbon-like structures whose width inversely correlates with applied stress magnitude. The newly etched edges are macroscopically straight or serrated, predominantly Mo-zigzag terminated, and enhance photoluminescence by a factor of ~8.0. The edge type depends on the angle between stress direction and crystallographic orientation, corroborated by theoretical calculations. Biaxial stressing generates well-defined nano-squares, offering a scalable, versatile patterning route for engineering 2D materials with tailored functional edges, promising for electrocatalytic and optoelectronic applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3969-9
Phosphor-in-glass (PiG) materials are promising color converters for high-power laser illumination, yet suppressing interfacial reactions between phosphor and glass matrix at elevated sintering temperatures remains a critical challenge. Here, we report a Y3Al5O12:Ce3+ (YAG:Ce) phosphor-in-silica glass (PiSG) with high SiO2 content (>85 wt%) fabricated via a Cs2CO3 flux. Incorporation of Cs2O significantly inhibits SiO2-YAG:Ce reactions, preserving internal quantum efficiency (IQE) at 97.7% of pure YAG:Ce, and achieving 88.3% IQE even after calcination at 1400°C for 2 h. In contrast, smaller alkali ions (Li+, Na+) accelerate YAG:Ce decomposition. Mechanistic studies reveal that Cs+ with large ionic radius and weak interaction with oxygen suppresses non-bridging oxygen (NBO) formation, promoting a complete silica network that limits alkali ion diffusion. Leveraging the mixed alkali effect (10% Li2O + 5% Cs2O), the PiSG exhibits enhanced hydrothermal stability, withstanding 200°C treatment for 10 h. A PiG film-sapphire device delivers 3080 lm luminous flux and 213 lm W−1 efficiency under blue laser excitation. These findings establish YAG:Ce-PiSG as a highly promising color-conversion material for high-performance laser illumination.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4030-y
In the era of artificial intelligence, efficient perception and processing of massive visual information demand advanced machine vision systems. Inspired by human visual adaptation, various optoelectronic devices have been developed, yet most rely on external gate voltages or complex circuits for dynamic sensitivity modulation. This work demonstrates an all-optically controlled biomimetic sensor based on a one-dimensional ZnO/MAPbBr3 heterojunction, achieving both positive and negative photoconductivity effects. By modulating oxygen vacancy states with ultraviolet light, the competition between intrinsic photoconduction and trap-mediated carrier capture is regulated, enabling dynamic control of visible-light photoresponse within a single device. This tunable behavior mimics scotopic adaptation (photopigment regeneration under weak illumination), photopic adaptation (photopigment bleaching in bright environments), and eyelid-like self-protection against intense light. The device operates without external gate bias or cascaded circuits, offering a promising strategy for next-generation intelligent biomimetic sensors in machine vision.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4052-0
Cutaneous wound infections affect millions of patients annually worldwide, and early diagnosis is critical for timely anti-infection treatment. Bacterial infections alter wound pH, offering a promising diagnostic approach. Here, a diagnostic smart dressing (CMC-PDBI) is developed by ultraviolet-initiated crosslinking of a pH-responsive indicator coating, incorporating modified bromothymol blue, onto a carboxymethyl cellulose substrate. The dressing exhibits superior pH-triggered color-changing performance in both phosphate buffer solution and bacterial cultures across the pH range associated with wound infection (orange at pH 6.0, green from pH 6.5 to 7.5, blue at pH 8.0). In a murine wound infection model, CMC-PDBI indicates infection two days before symptomatic manifestation. Early therapy guided by the dressing accelerates wound healing and reduces inflammation. A smartphone application (InfectSense) assists in identifying infection risk. This work presents a novel early-warning platform for qualitative visual diagnosis of wound infections before clinical symptom onset, with high potential for clinical and home care settings.