SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3793-9
Organic solar cells (OSCs) require both a high donor/acceptor (D/A) interfacial area for efficient exciton dissociation and a vertically phase-separated morphology for efficient charge transport. Traditional bulk heterojunctions (BHJs) provide large interfacial areas but lack vertical phase separation, while quasi-planar heterojunctions (QPHJs) achieve vertical separation at the cost of reduced interfacial contact. Here, we introduce an in situ pore-forming strategy for polymer thin films. By incorporating an excess of additives as pore-forming agents into the donor layer, a nanoporous film with a fibrous nano-network is generated. Subsequent deposition of acceptor molecules fills these nanopores, creating a hybrid planar/bulk heterojunction (HP/BHJ) that synergizes the strengths of both architectures. This design enhances performance by: (1) increasing the D/A interfacial area via nanopores, forming a three-dimensional network that accelerates exciton dissociation; (2) promoting close molecular packing that minimizes carrier recombination and establishes low-defect charge transport channels; and (3) fostering vertical phase separation through layer-by-layer deposition. Binary OSCs fabricated with this strategy achieve a power conversion efficiency (PCE) of 20.0%, surpassing conventional BHJ and QPHJ devices by a significant margin. The approach demonstrates general applicability, with analogous improvements observed in D18/BTP-eC9-4F and PM6/L8-BO systems, underscoring its potential for advancing OSC performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3615-1
Stretchable electronics are pivotal for bio-integrated devices, soft robotics, and wearables, yet their development is constrained by single-layer architectures that limit integration density and by mechanical mismatch between rigid components and soft substrates, which curtails service life. Here, we introduce a LEGO-like modular assembly strategy to construct multilayer three-dimensional (3D) stretchable electronics. Electronic components (ECs) and self-healing polyurethane (SPU) substrates patterned with liquid metal (LM) circuits serve as the modular blocks. This design simplifies fabrication and markedly enhances 3D integration density. The combination of LM circuits and self-healing elastic substrates enables devices to withstand diverse deformations and to autonomously heal after mechanical damage. Notably, the devices can undergo multiple recycling and reuse cycles without significant performance loss. This methodology offers a new paradigm for advanced flexible electronics, addressing critical bottlenecks in integration density, mechanical robustness, and sustainability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3671-0
Photothermal therapy (PTT) is a non-invasive tumor treatment that offers controllability, non-drug resistance, and precise ablation, yet its efficacy is limited by uncontrolled heat diffusion and weak immune responses, often leading to metastasis. Here, we report a chondroitin sulfate-modified Prussian blue-montmorillonite immunoregulator (PM@CS) that integrates tumor cell adhesion and Golgi targeting to confine photothermal damage at the organelle level. PM@CS accumulates on the Golgi apparatus, reducing heat transfer distance and enhancing photothermal ablation. This targeted hyperthermia disrupts post-translational modification and secretion of metastasis-associated proteins, with GOLPH3 and GOLM1 expression reduced by 63.4% and 70.3%, respectively. Furthermore, PM@CS promotes dendritic cell maturation (3.3-fold increase in CD80+ and CD86+ populations) and enhances antigen-specific CD4+ and CD8+ T cell proliferation, attributed to the immunoadjuvant properties of montmorillonite. Notably, PM@CS upregulates voltage-gated calcium channels (CaV) and enhances Ca2+ influx, activating calcium signaling cascades that amplify immunotherapy. This synergistic approach inhibits primary tumor growth and lung metastasis, offering a promising strategy for cancer treatment.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61066-9
Carbon materials suffer from limited dielectric loss, resulting in poor impedance matching and inadequate microwave attenuation. To address this, hierarchical structures with synergistic loss mechanisms are sought. Here, biomass cattail serves as a sustainable precursor for nitrogen-doped carbon nanotube arrays decorated with Fe3C nanoparticles via chemical vapor deposition, yielding Fe3C@NCNTs/CMTs composites. The crystallinity, tuned by calcination temperature, critically influences microwave absorption. At 800 °C, the composite achieves a minimum reflection loss of –35.8 dB and an effective absorption bandwidth of 7.02 GHz at a thickness of only 1.7 mm, with an ultralow filler loading of 10 wt%, covering the entire Ku band and part of the X band. This performance stems from enhanced magnetic loss and multiple dielectric polarization mechanisms. The study demonstrates a promising strategy for designing biomass-derived carbon-based broadband microwave absorbers.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3883-2
Tensile stress annealing (TSA) is an effective strategy for tailoring magnetic anisotropy and high-frequency performance in nanocrystalline soft magnetic alloys. Here, we systematically investigate the influence of TSA on the microstructure, magnetic domain evolution, and permeability stability of Fe69.5Co3Nb2Mo1.5Si14B9Cu1 nanocrystalline alloys. Across all applied stresses (0–300 MPa), the alloys retain an ultrafine grain size (≤11 nm), yet the induced uniaxial anisotropy constant (Ku) rises sharply from 22.5 to 665 J/m3. This increase in Ku refines the magnetic domain structure, reducing average domain width from 110 to 36 μm, and shifts the magnetization mechanism from domain-wall displacement to rotation-dominated reversal. Quantitative correlation between Ku, domain structure, and effective permeability (μe) reveals that higher stress suppresses μe at low frequencies but yields exceptional frequency stability: μe ≈ 2330 is maintained up to 1 MHz at 50 MPa, and μe ≈ 585 remains constant from 1 kHz to 10 MHz at 300 MPa. These findings demonstrate that stress-induced anisotropy is a decisive factor in governing high-frequency magnetic response, offering both mechanistic insight and a practical framework for designing next-generation soft magnetic materials for precision current transformers, EMC filters, and MHz-class power electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3772-y
Conformal contact between functional electronic films and biological surfaces is critical for long-term device stability, high signal sensitivity, and favorable signal-to-noise ratio. Traditional transfer methods, such as soft stamps and pad printing, often involve mechanical pressing, leading to poor conformality, localized stress concentration, or structural failure. Alternative strategies, including geometric engineering of non-stretchable materials or using stretchable organic alternatives, mitigate these issues but increase design complexity and reduce fabrication efficiency. Here, we highlight a novel 'drop-printing' strategy introduced by Li et al. that leverages capillary force to manipulate a water droplet to pick up a thin film, transfer it to a target substrate, and print it onto the surface. As the droplet evaporates, the film conformally wraps the surface. The droplet acts as a lubricating layer, while interfacial liquid penetrating microstructures generates capillary pressure, facilitating shape-adaptive deformation and significantly reducing stress concentration. The final positioning and conformality are governed by droplet behavior on the target surface. This approach achieves positional deviation of less than 20 μm via regulation of three-phase contact lines. The strategy enables damage-free conformal wrapping of non-stretchable films onto three-dimensional biological surfaces, as demonstrated by drop-printed silicon microfilm conformally wrapping on a rat brain, with successful NIR laser stimulation triggering forelimb movement and synchronized brain electrophysiological signals. This gentle, high-precision method addresses the pressing need for low-stress conformal bioelectronics, offering a general solution for diverse biological interfaces.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225185
Sulfur hexafluoride (SF6), widely used as an insulating gas in high-voltage electrical equipment, possesses a global warming potential (GWP) 25,200 times that of CO2, necessitating efficient degradation technologies. This study employed computational fluid dynamics (CFD) to simulate the thermal catalytic degradation of SF6 in a fixed-bed reactor, integrating models for porous media, heat transfer, turbulence, and chemical kinetics. The simulations revealed significant radial non-uniformities in pressure, velocity, temperature, and species concentration distributions, with temperature identified as the dominant factor influencing degradation efficiency. Radial temperature gradients caused uneven reaction rates, with degradation rates near the wall substantially exceeding those at the central axis, thereby reducing overall SF6 conversion. To address this, structural optimizations were implemented, including reducing the reactor tube diameter and incorporating inert porous media with high thermal conductivity at both ends of the catalytic section. These modifications enhanced radial heat transfer, homogenized the temperature field, and improved the uniformity of reaction rates and species concentrations. Parametric studies on inlet gas velocity showed that both excessively low and high flow rates were detrimental: low velocities led to underutilization of the downstream catalyst and increased energy consumption, while high velocities deteriorated heat transfer and exacerbated radial temperature gradients. The optimal inlet velocity range was determined to be 0.4–0.8 m/s for a reactor tube inner diameter of 10 mm, balancing catalyst utilization, energy consumption, and degradation efficiency. This research provides data-driven guidance for the design and scale-up of SF6 catalytic degradation reactors.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60624-4
Para-xylene (PX) is a critical chemical feedstock for producing polyesters, plastics, and fibers, with China's 2024 consumption reaching 40 million tons (63% of global total) and an import dependency of 17%. Conventional naphtha-based routes face feedstock security and cost volatility, prompting interest in syngas conversion. This review systematically examines recent catalyst developments for direct syngas-to-PX-rich aromatics, focusing on three systems: Fischer-Tropsch synthesis (FTS) catalyst/zeolite coupling, methanol synthesis catalyst/zeolite synergy, and dual-engine/zeolite catalysis. Critical parameters such as active component electronic structure, promoter effects, and zeolite pore topology are analyzed to reveal governing principles of activity, selectivity, and stability. Reaction mechanisms via olefin, methanol, and dual-intermediate pathways are explored. Current bottlenecks include coordinated optimization of activity and stability, and unclear regulation of PX selectivity. Future research directions are proposed to address these challenges.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3895-7
Flexible transparent electrodes are vital for next-generation electronics, but conventional silver nanowire (AgNW) networks suffer from non-uniform current and “hot spots” due to their random arrangement. To address this, we present a facile rubber pressure treatment that enables the controlled self-assembly of ordered AgNW micromesh (Ag NMs) on hydrophilic surfaces. This simple physical treatment simultaneously modifies surface energy and topography through molecular chain transfer from the rubber, creating optimal wetting conditions for coffee-ring assembly. This dual modification transforms droplet evaporation from constant contact angle to constant contact radius mode, enabling the universal fabrication of well-defined Ag NMs on diverse substrates like glass, polymers, and even curved surfaces. The resulting Ag NMs/colorless polyimide (CPI) electrodes (2 cm × 2 cm, ~30 Ω/sq), fabricated via single-step transfer and embedding, demonstrate desirable uniform sheet resistance distribution (<5% variation), outstanding mechanical durability, and environmental stability. These electrodes exhibit superior performance in practical applications, including stable electrical heating (159 ± 3°C at 8 V) with uniform temperature distribution and excellent electromagnetic interference (EMI) shielding (26.4 dB), while maintaining high optical transparency (~78%). This scalable approach offers a promising platform for advanced flexible electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4009-0
Micro light-emitting diode (Micro-LED) display technology is a promising next-generation display technology due to its high brightness, high contrast, low power consumption, long life, and fast response. However, aggressive downscaling of Micro-LEDs to a few microns makes lift-off fabrication of metal bumps for soldered joints between Micro-LEDs and driver substrates increasingly difficult, challenging high-yield bump arrays under high-density conditions. This study innovatively replaces conventional metal bumps with a photosensitive conductive polymer (PCP), enabling fabrication of polymeric micro-bump arrays via well-established photolithography, bypassing complex lift-off processes and reducing short-circuit risk. Isopropyl alcohol regulates developer wettability for optimal development, yielding bump arrays with bump size 20 μm × 12 μm and height (1.9288 ± 0.0213) μm on thin-film transistor (TFT) drivers with yield over 99.99%. The issue of low bonding yield from polydimethylsiloxane (PDMS) thermal expansion was resolved by adjusting chip spacing on the temporary substrate, achieving bonding yield exceeding 99.8%. A 0.99-inch full-color Micro-LED display with density 114 pixels per inch (PPI) and brightness 5537 cd/m² was fabricated. High-yield bump arrays, Micro-LED arrays, and high bonding yield are highly reproducible, promoting development of Micro-LED displays and related fields.