SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4472-0
Dynamic electrocardiography (ECG) monitoring during physical activity remains compromised by motion artifacts that corrupt signal fidelity, particularly with conventional gel electrodes whose impedance rises sharply under deformation. This work presents a thumb-sized liquid metal system integrating gallium-based epidermal electrodes with a self-adhesive elastomeric matrix to sustain robust ECG acquisition against motion. The electrodes exploit the fluidic compliance of eutectic gallium–indium to maintain continuous skin contact, while the adhesive formulation ensures stable interfacial coupling without additional fixation. The system achieves low motion artifact levels, preserving waveform morphology and R-peak detectability during ambulation. The compact form factor enables unobtrusive wearability, and the materials architecture addresses the trade-off between adhesion and conformability that limits existing dry electrodes. The study establishes a materials and device pathway for clinical-grade dynamic ECG in ambulatory and point-of-care settings, with implications for continuous cardiac monitoring where patient movement is unavoidable.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4412-y
GeTe-based thermoelectric materials are promising lead-free alternatives to PbTe, but their intrinsically high Ge vacancy concentration (~10^21 cm^-3) leads to excessive carrier density and degraded Seebeck coefficient. This study integrates resonant levels (RLs) via In doping and local van der Waals gaps via Sb/Bi alloying to decouple electron and phonon transport. The optimal composition Ge0.91Sb0.04Bi0.04In0.01Te exhibits a Seebeck coefficient of ~287.31 μV K^-1 at 323 K, more than double that of the In-free sample (~102.28 μV K^-1). The peak figure of merit zT reaches ~1.8 at 723 K, with an average zT of ~1.0 over 323–723 K. Vickers hardness is enhanced to ~224 HV, a ~93% improvement over pristine GeTe (~116 HV). X-ray diffraction reveals a structural evolution toward a pseudo-cubic phase with increasing In content, and the (202) peak shifts to lower angles, indicating lattice expansion. These results demonstrate that synergistic RLs and van der Waals gaps effectively optimize carrier concentration and suppress thermal conductivity, offering a viable route for high-performance, mechanically robust GeTe thermoelectrics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4417-x
Balancing mechanical strength, corrosion resistance, and soft magnetic performance in structural-functional integrated materials remains a persistent metallurgical challenge. This study reports a face-centered cubic (FCC) Fe40Co35Ni15Al3Ta2Cr5 (at.%) high-entropy alloy (HEA) that achieves an unprecedented combination of these properties. The alloy exhibits a tensile strength of ~1200 MPa, total elongation of ~25%, saturation magnetization of 101.54 Am2·kg-1, and coercivity of 267.34 A·m-1. These values surpass most reported magnetic HEAs and conventional soft magnetic alloys. In a simulated 3.50 wt.% NaCl seawater environment, the alloy demonstrates a corrosion current density of 3.99 × 10-7 A·cm-2, comparable to 316L stainless steel. The synergy arises from nanoprecipitate engineering within the FCC matrix, which impedes dislocation motion while maintaining magnetic domain wall mobility and promoting a protective passive film. This work provides a design pathway for soft magnetic structural-functional materials suitable for corrosive marine environments, where simultaneous load-bearing and magnetic actuation are required.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4177-3
Chirality profoundly influences tumor therapy by regulating key physiological processes, yet the link between chirality and therapeutic properties of atomically precise metal nanoclusters (NCs) remains poorly understood. Atomically precise Au25 NCs protected by chiral cysteine ligands (L-Au25(cys)18, D-Au25(cys)18, and Rac-Au25(cys)18) were constructed and systematically investigated to elucidate the association between chirality and tumor therapeutic performance. Although no significant difference in enzyme-like activity was observed among the three NCs, Rac-Au25(cys)18 exhibited enhanced reactive oxygen species generation under 808 nm laser irradiation, achieving superior phototherapeutic effects in both in vitro and in vivo tumor models. The chiral Au25 NCs induced distinct cell death pathways: L-Au25(cys)18 primarily triggered ferroptosis, D-Au25(cys)18 induced both ferroptosis and apoptosis, and all three NCs activated disulfidptosis. In vivo, tumor inhibition rates for L-Au25, D-Au25, and Rac-Au25 groups were 46.7%, 42.5%, and 68.3%, respectively, with no significant body weight fluctuations and minimal hepatorenal toxicity. Hematological and histopathological analyses confirmed favorable systemic biocompatibility. This work clarifies the correlation between chiral structures and tumor therapeutic performance of gold NCs, providing experimental insights and theoretical support for the design of novel chiral nanomaterials and optimization of precise tumor phototherapeutic strategies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4202-3
Carbon dots (CDs) with absorption in the second near-infrared window (NIR-II, 900-1700 nm) hold promise for tumor theranostics, yet existing synthesis methods often involve complex procedures, harsh conditions, or lack precise control. Here we report a 'self-photooxidation-restructuring' strategy that enables structural reorganization of the carbon core in CDs, achieving a significant redshift of absorption into the NIR-II region. Under ultraviolet (UV) light irradiation, the precursor (B-CDs, absorption in UV region) generates singlet oxygen, which self-oxidizes aldehyde groups and the carbon skeleton of B-CDs to stronger electron-withdrawing carboxyl groups and carbon radicals, respectively. These processes facilitate the formation of new C=C bonds between isolated aromatic domains, thereby transforming B-CDs into novel CDs (N-CDs) characterized by enhanced donor-acceptor interactions and a redshift in absorption toward the NIR-II window. Various experimental data, including high-resolution XPS, FTIR, NMR, EPR, have proved the proposed formation mechanism. The novel N-CDs afforded a high photothermal conversion efficiency of up to 71.33%, which enabled 1064 nm laser-activated photoacoustic imaging (PAI)-guided photothermal therapy (PTT) in tumors. This work opens a new avenue for the synthesis and modulation of CDs in the NIR-II region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4277-1
Two-dimensional (2D) magnetic materials hold promise for next-generation spintronics, yet most exhibit Curie temperatures (Tc) far below room temperature, limiting practical applications. Here, we report the realization of room-temperature ferromagnetism in CuCrSe2 nanosheets via controlled anion removal achieved by post-synthetic vacuum annealing. Raw CuCrSe2 shows a low Tc of ~120 K, whereas annealed CuCrSe2 (A-CuCrSe2) nanosheets exhibit robust ferromagnetic ordering above 300 K. Structural and compositional analyses, including transmission electron microscopy, Raman spectroscopy, and X-ray absorption spectroscopy, confirm that A-CuCrSe2 retains the original layered crystal structure with an estimated Se vacancy concentration of approximately 10%. Magnetic measurements reveal room-temperature ferromagnetism in exfoliated nanosheets, corroborated by magnetic imaging and electric transport measurements. Anomalous Hall effect (AHE) measurements uncover the coexistence of two ferromagnetic phases within the same sample: one with low Tc (~120 K) and another with high Tc (>300 K), indicating spatially heterogeneous magnetic ordering driven by anion removal distribution. Density functional theory (DFT) calculations elucidate the microscopic mechanism, suggesting that Se vacancies modulate the magnetic exchange interactions, enhancing Tc. This work demonstrates that anion modulation is an effective intrinsic strategy to achieve room-temperature ferromagnetism in 2D materials, potentially advancing spintronic applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3831-0
Ammonia decomposition is a key process for generating COx-free hydrogen, yet conventional cobalt catalysts require high temperatures (>550 °C) to overcome the strong Co–N binding that limits N2 desorption. Here we report a novel Co catalyst supported on a Ce and N co-modified perovskite (Co@La_xCe_{1-x}AlO_{3-y}N_z) that achieves 92.6% ammonia conversion with a hydrogen production rate of 9.7 mmol g−1 min−1 at 425 °C and GHSV = 9000 mL h−1 g_cat−1, representing a 125 °C reduction in operating temperature relative to conventional Co-based catalysts. Mechanistic studies using isotopic labeling and in-situ DRIFTS reveal that synergistic Ce and N modification creates a unique LA-L(A+B)-LB active site configuration, which lowers the Schottky barrier at the metal-support interface and promotes facile hydrogen spillover. The reaction proceeds via an interfacial Mars-van Krevelen mechanism, contrasting with the traditional Langmuir-Hinshelwood pathway on conventional Co catalysts. This work provides new insights for designing low-temperature Co-based ammonia decomposition catalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3605-0
Nickel oxide (NiOx) is widely used as a hole transport material in inverted perovskite solar cells (PSCs). However, its practical application is limited by low intrinsic conductivity and insufficient hole extraction ability, leading to significant interfacial defects that reduce device efficiency and stability. To overcome these issues, two isomeric small organic molecules, 2,6-NOT and 1,5-NOT, were developed and introduced to modify NiOx. These isomers share the same structure but differ in the substitution positions of functional groups, resulting in distinct molecular planarity. Experimental results demonstrate that 1,5-NOT, featuring extended conjugation and enhanced planarity, more effectively enhances the hole extraction/transport capabilities and conductivity of NiOx compared to 2,6-NOT. The NiOx/1,5-NOT-based device achieves a remarkable power conversion efficiency (PCE) of 24.20%, along with excellent long-term stability, surpassing the NiOx control device (18.12%) and the 2,6-NOT-based device (21.87%). These findings indicate that modifying NiOx with small organic molecules significantly improves charge transport performance, and increasing molecular planarity is particularly beneficial for enhancing hole transport and reducing defect density, thereby increasing both efficiency and stability. This work provides a new strategy for NiOx modification via small organic molecules, offering a promising route to high-performance inverted PSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4022-7
Transition metal nitrides (TMNs) have emerged as promising alternatives to noble metals in electrocatalysis due to their noble metal-like electronic structures, high conductivity, low cost, and robust chemical stability against corrosion and oxidation under harsh conditions. The rational design and controlled synthesis of TMNs with distinct structures are crucial for developing highly efficient electrocatalysts. This review comprehensively summarizes representative synthetic strategies for TMNs, including direct nitridation, solid-state reaction, sol-gel assisted reaction, and wet-chemical reaction. It presents distinct structural characterizations and demonstrates their advances in electrochemical applications. Finally, the remaining challenges and future research directions for exploring TMNs with well-defined structures are proposed, aiming to guide the development of high-performance electrocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3777-0
Optically clear adhesives (OCAs) are critical for next-generation optoelectronic systems, yet their end-of-life management remains a sustainability challenge. Here, we report a debondable and robust polyurethane (PU)-based OCA that integrates both mechanical and chemical recyclability. The PU-based OCA exhibits high optical transparency (>90% transmittance from visible to near-infrared), strong adhesion to glass and polymeric substrates (bonding strength up to 5.0 MPa), and thermally sensitive H-bonding interactions that enable on-demand deadhesion at elevated temperatures. This capability facilitates non-destructive detachment of functional assemblies, promoting component reuse and material recycling. The adhesive demonstrates excellent mechanical properties, including ductility and strength, and outperforms several commercial optical adhesives in key performance metrics. Its straightforward synthesis and industrial scalability make it a promising solution for advancing circular economy principles in optoelectronic device manufacturing. The work addresses critical bottlenecks in balancing mechanical performance, adhesion/detachment, and recyclability, offering a transformative approach to sustainable advanced manufacturing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3678-1
Reed membrane, a natural cellulosic material traditionally used in musical instruments, holds promise in flexible electronics due to its abundance, low cost, and excellent biocompatibility. However, its native form contains water-soluble ions and lipid-soluble waxes that hinder performance in acoustic and electronics by compromising electrical insulation and mechanical stability. Here, supercritical fluid superposition purification (SCSP-WA) is introduced, which utilizes supercritical CO2 with water and acetone as bipolar co-solvents to selectively remove these impurities. Post-SCSP-WA treatment, the reed membrane exhibits significant enhancements in mechanical strength and electrical insulation, achieving a 4-fold increase in elongation at break, improved tensile strength and Young’s modulus, and a 98.5% reduction in leakage current, all while maintaining low and stable capacitance. These improvements stem from the restructuring of the fibrous network into a porous, interconnected microstructure. Material characterization (X-ray photoelectron spectroscopy (XPS), Fourier-transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM)) confirmed the effective removal of magnesium and waxy functional groups, along with enhanced fiber crosslinking. Cytotoxicity tests further validated the biocompatibility of the SCSP-WA-treated membranes. This environmentally sustainable approach expands the potential of reed membranes in flexible bioelectronics and bio-integrated acoustic systems.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024110703
Urban river ecosystems are increasingly threatened by anthropogenic activities, necessitating comprehensive health assessments beyond conventional water quality metrics. This study evaluates the ecological health of the Zhongshan South Road reach in Wuhu, China, by integrating microbial community integrity with physicochemical parameters. Nine monitoring sections were established, considering land use, pollution sources, and seasonal hydrology. Over four seasons, eight water quality parameters and microbial indicators were systematically monitored. A Microbial Index of Biotic Integrity (M-IBI) was developed through candidate parameter screening, interference response analysis, and discriminant ability assessment. Core metrics included Chao1 index, Sobs index, and relative abundances of Acinetobacter and hgcl-clade genera. M-IBI scores were standardized and classified into health levels, with results compared against the Water Quality Index (WQI). Findings revealed seasonal M-IBI variation: winter > autumn > summer > spring, with downstream water quality superior to upstream. Spatial and seasonal patterns of WQI and M-IBI were largely concordant, though discrepancies arose from differential microbial responses to environmental factors and heightened sensitivity to human disturbance. The M-IBI approach demonstrated robust applicability for river health assessment, offering a sensitive, integrative tool for urban water management.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112603
Sulfamethoxazole (SMX) and microplastics (MPs) are ubiquitous co-existing pollutants in aquatic environments. This study investigated the effects of polyethylene (PE), polypropylene (PP), and polystyrene (PS) MPs with varying aging degrees on the photodegradation of SMX. In the absence of MPs, SMX photodegradation was only 28%, while the presence of virgin PE increased it to 34%. Aging PE for 200, 400, and 600 h further enhanced degradation to 46%, 56%, and 77%, respectively. Pseudo-first-order kinetics showed that the rate constant (kobs) increased from 0.066 h−1 to 0.224 h−1 with aged PE. Aged MPs generated more reactive oxygen species (ROS) under irradiation, including hydroxyl radicals (·OH), singlet oxygen (1O2), and superoxide anions (O2·−), as confirmed by radical quenching and EPR analysis. Density functional theory identified the benzene ring, five-membered heterocycle, and sulfonyl group as primary ·OH attack sites. LC-MS analysis revealed degradation products such as p-aminobenzenesulfonamide, indicating both direct and indirect photolysis pathways. This work provides mechanistic insights into antibiotic-MP interactions and informs strategies for managing co-existing pollutants.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225227
Imidazolium-based ionic liquids (ILs) are foundational materials in sustainable chemical engineering due to their negligible volatility, exceptional thermal stability, and tunable properties. This study details the development, optimization, and analysis of an industrial-scale green synthesis pathway for 1-butyl-3-methylimidazolium chloride ([Bmim]Cl) via quaternization of N-methylimidazole with 1-chlorobutane. Reaction parameters were optimized using orthogonal experimental design, and process intensification strategies were implemented to enhance efficiency and environmental sustainability. The optimal conditions were identified as a reaction temperature of 76 °C, a molar ratio of N-methylimidazole to 1-chlorobutane of 1:1.3, and a reaction time of 36 h, achieving a single-pass yield of 95.6%. Kinetic studies revealed a significant correlation between temperature, molar ratio, and conversion efficiency, with an activation energy (Ea) of approximately 135.7 kJ/mol, indicating pronounced temperature dependence. A closed-loop material recycling system was designed, enabling recovery rates of 99.5% for 1-chlorobutane and 98.1% for ethyl acetate, thereby curtailing raw material consumption and waste generation. This approach aligns with green chemistry principles and propels the process toward near-zero emissions. The pathway offers a scalable model for [Bmim]Cl manufacture and a transferable strategy for synthesizing other ionic liquids, representing a substantial advancement in sustainable process engineering.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3451-2
Visual aesthetics is a key metric of semi-transparent organic photovoltaics (ST-OPVs) for building-integrated solar windows, yet previous studies have primarily focused on the compromise between efficiency and transparency. This work addresses the overlooked aspect of full visual aesthetic control, particularly the bidirectional reflected color for architectural harmony, via designing ST-OPVs with double-sided ultra-thin Ag/TeO2 transparent electrodes. This design facilitates full-spectrum color tunability covering the whole standard color gamut of CIE coordinates on both surfaces, achieved simply by adjusting layer thicknesses. The resulting devices exhibit neutral transparency (16.6%–27.0% average visible transmittance) and competitive power conversion efficiencies (8.1%–9.2%). Additionally, the devices demonstrate strong flexibility, with flexibility-adaptive coloration and curvature-enhanced aesthetics. This work presents an ST-OPV design featuring full visual aesthetics and considerable performance, paving the way for commercialization of organic solar windows for building and vehicle integration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3487-x
Continuous carbon fiber-reinforced ZrB2-SiC ceramic matrix composites are promising thermal protection materials for hypersonic vehicles and reusable spacecraft. Although injection-assisted vacuum impregnation (IVI) offers advantages such as shorter processing cycles, lower costs, and reduced fiber damage compared to conventional methods, phenolic/acetone-based IVI systems yield composites (designated as CPS) with limited ceramic contents. To address this, an aqueous slurry-based IVI approach was developed, producing composites designated as CHS. After a single IVI cycle, CHS achieved a ZrB2 phase volume fraction of 25 vol.%, 47% higher than CPS, while reducing processing time by 49%. After chemical vapor infiltration, CVI-CHS composite exhibited a room-temperature compressive strength of 106.78±10.53 MPa, representing a 28% improvement over CVI-CPS. Crack propagation analysis revealed discontinuous zigzag patterns under compression, dominated by fiber bridging and pull-out energy dissipation mechanisms. Flexural results revealed both composites retain considerable strength (111.15±12.46 and 83.15±12.03 MPa) along with low flexural modulus (13.00±2.41 and 13.52±6.99 GPa) and high strain tolerance (1.32%±0.018% and 1.07%±0.34%). It is attributed to the anisotropy of fiber preforms and the elastic modulus mismatch among different phases, which hindered effective constraint of fibers by the matrix and, in turn, facilitated mitigation of stress concentration. Additionally, CVI-CPS demonstrated superior X-band electromagnetic interference (EMI) shielding (34–36 dB) compared to CVI-CHS (22–27 dB), resulting from synergistic effects between pyrolitic and deposited carbon in the matrix of the former. Both composites showed enhanced EMI shielding efficiency with increasing temperature up to 600°C. This eco-friendly aqueous IVI strategy enables high-performance, cost-effective thermal protection materials with higher ceramic loading and tunable multifunctional properties.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61100-6
Sodium-ion capacitors (SICs) are attractive for low-cost and safe energy storage, but their practical development is limited by sluggish Na+ storage kinetics and structural instability of anodes. Control of both bulk structure and surface chemistry can address these limitations. We report a heteroatom-rich porous carbon (HRPC) derived from spores via hydrothermal pretreatment, low-temperature carbonization, and acid-mediated functionalization. The optimized GLSHC-HNO3 anode exhibits hierarchical porosity and multi-element co-doping, enabling rapid ion/electron transport, improved electrolyte wettability, and abundant Na+ adsorption sites. Density functional theory calculations reveal distinct contributions of different heteroatom configurations to sodium adsorption. The HRPC anode delivers an ultrahigh reversible capacity of 446.1 mAh g−1 at 50 mA g−1, retains 237.3 mAh g−1 at 2 A g−1, and shows excellent cycling stability. A full SIC with a polyaniline-derived porous carbon cathode achieves an energy density of 114.4 Wh kg−1 at 290 W kg−1, 43.1 Wh kg−1 at 1450 W kg−1, and a maximum power density of 5800 W kg−1, with 84.3% capacity retention after 5000 cycles and nearly 100% Coulombic efficiency. This work establishes a scalable, sustainable route for converting biomass into high-value carbon anodes, providing a new pathway for high-performance sodium-ion energy storage.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61116-X
A standardized dataset of linear sweep voltammetry (LSV) curves is presented for evaluating the oxygen reduction reaction (ORR) performance of carbon-supported catalysts in acidic media. All electrochemical tests were conducted in O2-saturated 0.5 mol L−1 H2SO4 at controlled rotation speeds using a rotating disk electrode. The dataset comprises 120 validated entries from both non-precious metal (MNC) and platinum-based (Pt-MC) catalysts, including original LSV curves and extracted performance parameters such as onset potential, half-wave potential, and limiting current densities at different rotation speeds. Data processing involved potential conversion to the reversible hydrogen electrode (RHE) scale, background subtraction, outlier removal, and reproducibility checks with defined quality control thresholds (relative standard deviation ≤2% for E1/2 and ≤5% for limiting current). The standardized collection serves as a reliable benchmark for catalyst performance comparison, supports kinetic and mass transport analysis, and provides a structured data source for machine learning applications in electrocatalysis. The dataset is openly available via Science Data Bank, with a DOI, and is intended as a dynamic resource for the ORR electrocatalysis community.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60629-3
This study reports the synthesis of a novel Z-scheme heterojunction composite film comprising Ag/Bi2MoO6/BiOBr via electrochemical processes, ion-exchange techniques, and subsequent photodeposition of silver nanoparticles. The incorporation of Ag nanoparticles exploits localized surface plasmon resonance (LSPR) effects and serves as an electron mediator, establishing a Schottky barrier that suppresses charge recombination. The optimized 1.5% Ag/Bi2MoO6/BiOBr film achieves a CO production rate of 13.65 μmol/(g·h) from photocatalytic CO2 reduction, significantly outperforming the unmodified Bi2MoO6/BiOBr film. Photocurrent and impedance analyses confirm enhanced charge separation in the Ag-modified composite. A non-linear relationship between Ag loading and photocatalytic efficiency was observed, with optimal performance at 1.5% Ag. The proposed Z-scheme mechanism elucidates the synergistic interactions among components, providing a scientific basis for rational design of advanced photocatalysts and immobilized systems for CO2 reduction. This work offers insights into the development of efficient, sustainable photocatalytic technologies for carbon capture and utilization.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605024
The refined quantification of carbon footprint in engineering construction projects is critical for formulating targeted carbon reduction strategies during the materialization phase. This study integrates material flow analysis (MFA) with the emission factor method to establish a panoramic carbon flow model for engineering projects. Construction activities are categorized into processing and construction, and office and daily operations, clarifying material and carbon flow relationships within the system boundary and with external systems. Empirical analysis was conducted on the Hejiawan Bridge of Section 11 of the Xiyu High-Speed Railway. Results show that the total carbon flow amounts to 27,482,432.11 kg CO2eq, with direct carbon flow (fuel oil, gasoline) accounting for 7.6% and indirect carbon flow (products, transportation, electricity) accounting for 92.4%. From the material flow perspective, the total carbon flow comprises product carbon flow (72.88%), resource and energy carbon flow (25.73%), transportation carbon flow (1.04%), waste carbon flow (0.35%), and service carbon flow (0.01%). In terms of activity scope, construction-related carbon flow accounts for 99.17%, while office and daily operations account for 0.46%. Two indicators, material consumption carbon flow rate and energy consumption carbon flow rate, are proposed for the first time. Comparative analysis of five girder bridges reveals that the Hejiawan Bridge has a material consumption carbon flow rate of 3.91 kg CO2eq/kg, ranking highest among similar bridges, while its energy consumption carbon flow rate is 13.40 kg CO2eq/kg ec, at a medium level. The assessment indicates relatively high material consumption, suggesting potential for carbon reduction through structural and geological optimization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3769-2
Proton exchange membrane water electrolyzers (PEMWEs) are pivotal for sustainable hydrogen production, yet the corrosion-induced TiOx on porous transport layers (PTLs) introduces Schottky contact barriers and pinch-off effects, severely impeding charge transfer and efficiency. Here, a cost-effective MoIrOx coating via spray deposition and thermal treatment on Ti felts is proposed. The coating forms a conductive interlayer that establishes a Schottky barrier staircase, reducing the effective electron transfer barrier and isolating TiOx from the ionomer to mitigate the pinch-off effect. The optimal PTL achieves a current density of 3.27 A cm−2 at 2 V, surpassing uncoated Ti felts by 59.5%. The MoIrOx interlayer suppresses localized electron accumulation at the interface, enabling stable operation with ultra-low catalyst loadings by preventing direct ionomer-TiOx contact. This work demonstrates a scalable strategy to enhance PEMWE efficiency and durability while minimizing precious metal reliance, offering critical insights into interface engineering for electrolyzers.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607013
This study investigated the synergistic effects of earthworm mucus and two biochar types (rice husk biochar and straw biochar) on heavy metal bioavailability during sludge composting. Sludge was amended with earthworm mucus alone or combined with biochars at varying proportions, and the impacts on physicochemical properties, total heavy metal concentrations, bioavailable fractions, and chemical speciation were analyzed. Results showed that mucus addition increased sludge pH and electrical conductivity (EC) but decreased total nitrogen (TN) and total phosphorus (TP) contents. Synergistic mucus-biochar composting further elevated pH and EC while reducing TN, with the optimal treatment being mucus plus 10% rice husk biochar. Mucus-only composting reduced total concentrations and bioavailability of Cd, Cu, Ni, Zn, and Pb. Adding biochars significantly enhanced these reductions. Specifically, mucus with rice husk biochar achieved the best Cd removal, with total and bioavailable Cd decreasing by 27.03%–55.68% and 9.52%–28.57% (P<0.05), respectively, compared to controls. Mucus with straw biochar was most effective for Ni, Zn, and Pb, reducing total contents by 3.81%–5.72%, 7.93%–34.62%, and 42.61%–79.46%, and bioavailable fractions by 2.90%–26.31%, 15.58%–24.14%, and 32.30%–36.88% (P<0.05), respectively. Speciation analysis revealed that Cd, Ni, and Pb carbonate-bound fractions transformed into residual forms, and exchangeable fractions shifted to Fe-Mn oxide-bound forms. Straw biochar addition resulted in the highest residual fractions for Cd, Cu, Ni, Zn, and Pb, increasing by 0.35%–7.02%, 8.61%–12.90%, 16.62%–23.02%, 17.33%–26.10%, and 16.12%–27.20% (P<0.05), respectively. These findings demonstrate that earthworm mucus combined with rice husk or straw biochar effectively reduces heavy metal concentrations and bioavailability in sludge, offering a promising strategy for sludge composting.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3892-2
Single-atom co-catalysts on semiconductor substrates offer a cost-efficient route to enhance photocatalytic performance with minimal precious metal loading. However, precise tuning of local coordination environments and construction of efficient single-atom co-catalysts remain challenging for overall water splitting. Here, we employ an icing-assisted photochemical reduction strategy to anchor atomically dispersed Pt species as hydrogen evolution co-catalysts on Al3+-doped SrTiO3 (Pt SA-STO). The optimized Pt SA-STO exhibits remarkable activity, with hydrogen and oxygen evolution rates of 13.62 and 6.71 mmol h−1 g−1, respectively, and a turnover frequency (TOF) of 2114.5 h−1. We pioneer the use of nuclear magnetic resonance (NMR) spectroscopy to quantitatively track the temporal evolution of Pt4+ to Pt2+ under continuous irradiation during the icing-assisted photoreduction. Advanced characterizations and theoretical calculations confirm that single-atom Pt co-catalysts facilitate directional transfer and extraction of photogenerated charge carriers, effectively suppressing surface recombination. This work provides insights into designing novel single-atom co-catalysts by deepening understanding of electronic configurations and active sites in photocatalytic overall water splitting.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4079-4
Utilization of ultrahigh-nickel LiNi_xCo_yMn_1-x-yO_2 (NCM) (x > 0.97) in Li-ion batteries can distinctively boost energy density through enhanced discharge capacity. However, capacity and thermal stability deteriorate as Ni content approaches the limit. Here, we propose a facile strategy by introducing high-valence tungsten (W) into ultrahigh-nickel polycrystalline LiNi_0.98Co_0.01Mn_0.01O_2 (PCNCM98). W-doped PCNCM98 (W-PCNCM98) exhibits refined, compactly stacked primary particles, whereas PCNCM98 shows equiaxial, non-uniform larger particles. The refined microstructure enhances mechanical strength: average particle hardness of W-PCNCM98 is 104 MPa, 1.5 times higher than PCNCM98 (68 MPa). This improved mechanical property suppresses lattice volume changes and relieves microcrack formation from H2–H3 phase transition. Consequently, cycling performance in pouch-type full cells is significantly enhanced, with capacity retention of 73% after 2000 cycles at 1 C and 25 °C, 54% higher than PCNCM98. Enhanced structural stability and strong electron affinity of W6+ also improve thermal stability: exothermic peak for W-PCNCM98 is postponed to 203 °C with heat generation of 1287 J g−1, versus 190 °C and 1528 J g−1 for PCNCM98. This high-valent doping strategy stabilizes ultrahigh-nickel NCM cathodes, accelerating large-scale EV applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3921-2
Moisture-enabled energy harvesting technologies offer a promising route for self-powered strain sensing, yet conventional generators suffer from slow response, poor recovery, and limited multidirectional resolution. Here, we report a stretchable thermoplastic polyurethane (TPU) nanofiber moisture-enabled electric generator (MEG) with highly aligned ion channels. A carbon black/sodium dodecylbenzene sulfonate (CB/SDBS) layer is coated on the TPU membrane, while carboxymethyl cellulose (CMC) and acidified poly(sodium 4-styrenesulfonate) (HPSS) are applied on opposite sides, establishing lateral hydrophilicity and ion gradients to drive directional ion migration. The planar MEG is lightweight, flexible, and requires no fully covered electrodes, enabling conformity to complex deformations. The aligned channels reduce ion migration tortuosity, enhancing ion transport efficiency and flux. As a result, the aligned MEG (ATMEG) delivers 0.2 V and 0.51 μA cm−2 at ~90% relative humidity, corresponding to 400% and 287% enhancements compared with the unaligned MEG (UATMEG). The ATMEG also exhibits ultrafast response (0.16 s) and recovery (0.08 s). Utilizing its anisotropic characteristics, a multidirectional self-powered strain sensor is developed, capable of distinguishing both the amplitude and direction of human motion, demonstrating strong potential for adaptive wearable electronics and intelligent motion monitoring.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608020
This paper systematically reviews the progress and achievements of China's collaborative innovation pilots for pollution and carbon emission reduction, identifies existing problems, and proposes targeted recommendations. As of the first batch, 64 pilot units (21 cities and 43 industrial parks) have issued implementation plans, with overall smooth progress and notable phased outcomes. Most pilots have actively promoted institutional and mechanism innovations, achieving substantial advancements in key sectors and critical areas, and yielding replicable practices. However, challenges persist, including fragmented interdepartmental collaboration, insufficient alignment of management systems, funding shortages for synergistic projects, and inadequate technological support. Recommendations include intensifying awareness campaigns, establishing coordinated promotion mechanisms, accelerating management system implementation, advancing core technology R&D, conducting progress evaluations, and amplifying publicity. For the second batch, suggestions focus on expansion strategies, pilot types, and selection methods, emphasizing incremental tasks, diverse pilot subjects (from provincial to enterprise levels), and clear articulation of expected outcomes and demonstration targets. The paper underscores the need to transform local experiences into institutionalized frameworks, fostering a four-dimensional synergy of carbon reduction, pollution control, green expansion, and economic growth, thereby contributing to China's ecological civilization and global climate governance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3843-9
Lignocellulose-based electromagnetic interference (EMI) shielding materials are gaining prominence across multiple sectors, driven by the growing EMI issues associated with rapid advances in communication technologies and electronic devices. These materials have demonstrated significant superiority over traditional EMI shielding solutions, which are often hampered by high cost and environmental concerns. This review emphasizes the excellent potential of lignocellulose as a cost-effective and flexible alternative to deliver the hierarchical structures and functional properties that qualify it for EMI shielding applications. The underlying EMI shielding mechanisms are then elucidated, with a focus on the benefits conferred by lignocellulose in such material systems. Furthermore, typical fabrication strategies for lignocellulose-based EMI shielding materials are comprehensively summarized, along with a discussion of their emerging applications in diverse scenarios. Finally, the challenges encountered in developing lignocellulose-based EMI shielding materials and their significant prospects for future boosting high-performance design and application are also outlined. The insights presented herein are expected to promote the development of efficient and green lignocellulose-based EMI shielding materials that meet the evolving demands of modern society.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3987-x
A hierarchically porous nickel salicylate (Ni-SA) metal-organic framework (MOF) was constructed via a salicylate coordination strategy to precisely modulate the microenvironment of nickel active sites for efficient electrocatalytic glucose oxidation. The ortho-hydroxy-carboxylate chelation directs atomic-level organization of Ni2+ sites within nanobelt assemblies, maximizing active site accessibility. Robust Ni–O coordination stabilizes Ni3+ intermediates during C–H bond cleavage, leading to remarkable catalytic stability. The optimized Ni-SA-2 catalyst achieved a high sensitivity of 5.97 mA mM−1 cm−2 and a low detection limit of 0.71 μM (S/N = 3), with 85.4% current retention after 8 h continuous operation. This design paradigm demonstrates universal applicability, as evidenced by successful extension to isostructural M-SA analogs (M = Co, Fe, Cr, Mn) under identical synthetic conditions, establishing metal-salicylate frameworks as a versatile electrocatalyst platform.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4004-3
The development of efficient and stable oxygen evolution reaction (OER) electrocatalysts is critical for clean energy technologies, yet conventional cobalt-based spinel catalysts often suffer from insufficient activity and structural instability under operating conditions. To address these challenges, this study proposes and constructs a cation-ordered spinel-like catalyst (HVI Metal-CoMoO4/NF). The unique crystalline framework induces significant Jahn-Teller distortion and pre-stabilizes a Co2+/Co3+ mixed-valence state at the cobalt active centers via asymmetric Co–O–Mo bridges, effectively optimizing bulk charge transport. Electrochemical tests demonstrate that its performance significantly surpasses that of benchmark materials, requiring only an overpotential of 307 mV to drive a current density of 100 mA cm−2 in 1.0 M KOH, with a Tafel slope of 63.13 mV dec−1, maintaining stable operation for over 320 h at high current density. Crucially, our structural and in situ characterization results clearly reveal a stable and well-crystallized reconstruction behavior from the surface into the bulk of the spinel-like pre-catalyst during the OER. This work fundamentally addresses the challenges of disordered reconstruction and unstable active phases in traditional spinel catalysts, providing a paradigm for regulating the dynamic evolution of electrocatalysts through precise structural design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4033-1
Photodetectors are critical components in modern optoelectronic systems, underpinning applications in optical communication, low-altitude economy, environmental monitoring, and national defense. Layered two-dimensional (2D) materials such as MoS2, WS2, black phosphorus (BP), and ReS2 have attracted extensive attention due to their remarkable electronic and optical properties, including facile mechanical exfoliation and tunable characteristics via thickness engineering. The absence of dangling bonds enables the construction of van der Waals (vdW) heterostructures free from lattice-matching constraints, promoting efficient charge transport, enhanced light absorption, and suppressed dark current. Among layered materials, semimetals such as graphene, PdTe2, MoTe2, and TaIrTe4 exhibit narrow or zero bandgaps, enabling ultrabroadband spectral responses from ultraviolet (UV) to terahertz (THz). ZrTe3, a layered gapless semimetal, demonstrates pronounced carrier transport features, including robust excitons and ultrafast carrier relaxation times, making it an ideal candidate for photodetection. However, pure ZrTe3-based photodetectors suffer from substantial dark current due to the absence of an energy bandgap, degrading signal-to-noise ratio and specific detectivity (D*). This work reports a high-performance broadband photodetector based on a ZrTe3/CuInP2Se6 heterostructure. By exploiting an asymmetric contact configuration that introduces a Schottky barrier, the device effectively suppresses dark current while enhancing photoresponse. The photodetector exhibits broad spectral sensitivity from UV to near-infrared (355–1177 nm), microsecond-level response speed, and high responsivity and specific detectivity. Beyond conventional photodetection, an optoelectronic information encryption-decryption application is demonstrated, where modulated light and bias voltage serve as dual input channels to encode and decode ASCII signals. This study resolves the challenge of high dark current in semimetal-based photodetectors and introduces a multifunctional platform for secure optoelectronic communication, highlighting the potential of ZrTe3 for next-generation photonic and quantum information technologies.