Acta Energiae Solaris Sinica•2026•DOI: 10.19912/j.0254-0096.tynxb.202608_9721
This study addresses the bearing failure mechanisms of pile anchor foundations for floating offshore wind turbines in layered soil. Using finite element analysis, the research investigates the coupled bearing performance under V-H, V-M, and H-M load combinations in complex layered soil conditions, based on the engineering geological conditions of an offshore clean energy site. A failure envelope method is employed to systematically evaluate the foundation's capacity. The study establishes a calculation method for assessing the in-place bearing capacity of pile anchors using limit load envelopes. Key findings indicate that the V-H load space envelope can determine the bearing performance dominated by uplift and lateral sliding failure. The eccentricity of the mooring point induces bending moments that significantly reduce the uplift bearing capacity, with the reduction increasing as the moment increases. The research provides a practical method for evaluating pile anchor bearing capacity under combined loads, facilitating the application of pile anchors in offshore clean energy development. The finite element model uses Plaxis 3D, with a pile diameter of 5.5 m, length of 77.5 m, and wall thickness of 100 mm, and employs the NGI-ADP model for clay. The study fills a gap in understanding pile behavior in layered soils, offering a robust tool for engineering design.
Acta Energiae Solaris Sinica•2026•DOI: 10.19912/j.0254-0096.tynxb.202608_9722
This study addresses the structural coupling mechanisms in large wind turbine blades by deriving a free vibration equation based on Euler-Bernoulli beam theory and Lagrange's equation, incorporating shear, bend-twist coupling, flap-lag coupling, and axial-bending coupling. The NREL 5 MW reference turbine serves as the case study. The formulation yields explicit mass and stiffness matrices, and the resulting eigenvalue problem is solved to quantify modal frequency shifts and mode shape variations. Results indicate that shear deformation reduces flapwise and edgewise frequencies, with second-order flapwise and edgewise modes decreasing by approximately 4.7% and 1.0%, respectively. Bend-twist coupling lowers bending frequencies while elevating torsional frequencies; the effect intensifies with mode order, as evidenced by a 3.1% reduction in third-order edgewise frequency and a 1.6% increase in second-order torsional frequency. Flap-lag coupling exerts a more pronounced influence on edgewise characteristics than on flapwise ones. Axial-bending coupling exhibits the least impact among the three coupling types. In terms of mode shapes, bend-twist and axial-bending couplings minimally affect low-order bending modes, whereas flap-lag coupling is the primary driver of pronounced coupling in bending mode shapes. These findings provide a reference for subsequent multi-degree-of-freedom coupled dynamic modeling.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4448-y
Zero-dimensional (0D) hybrid metal halides are promising for optoelectronic displays, bioimaging, and anti-counterfeiting due to strong exciton localization and self-trapped exciton (STE) emission. However, low-toxicity, biocompatible zinc halides with blue emission remain scarce, hindered by structural isolation of [ZnBr4]2− tetrahedra, electron-phonon coupling, lattice distortion, and nonradiative relaxation. Here, we synthesize MPAZnBr4 (MPA = N-(3-aminopropyl) morpholine), a 0D zinc bromide halide. Single-crystal X-ray diffraction reveals a monoclinic P21/c space group with a = 6.65190 Å, b = 16.11210 Å, c = 13.79640 Å, β = 94.5700°, Z = 4, and a calculated density of 2.394 g/cm3. The isolated [ZnBr4]2− tetrahedra are hydrogen-bonded to MPA cations, with the shortest Br···Br contact of 4.76 Å indicating weak inter-cluster electronic coupling. Upon photoexcitation, MPAZnBr4 exhibits bright blue emission centered at 450 nm with a full width at half maximum of 135 nm. Wavelength-dependent emission mapping confirms a single radiative pathway, while temperature-dependent photoluminescence identifies triplet STE emission with a thermal quenching activation energy of 55 meV. The extensive hydrogen-bonding network imparts remarkable structural stability, showing negligible photoluminescence decay under prolonged excitation or storage. As a proof-of-concept, we demonstrate switchable and rewritable information encryption and decryption, enabling complex luminescent patterns. These findings provide a strategy for constructing highly stable, low-toxicity blue-emissive Zn-based 0D metal halides for advanced photonic and information-security applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3676-3
Perovskite solar cells (PerSCs) have achieved remarkable efficiencies, yet their performance is limited by defect states and non-radiative recombination. Here, pyromellitic diimide (PD) is introduced as an additive to passivate bulk defects in perovskite films. PD forms hydrogen bonds with formamidinium (FA+) ions and coordinates with Pb2+ ions, effectively suppressing non-radiative recombination and reducing energy loss. The PD-treated perovskite films exhibit enhanced crystallinity and uniformity. Consequently, 1.55 eV PerSCs achieve a high open-circuit voltage (VOC) of 1.193 V and a power conversion efficiency (PCE) of 25.79%. Moreover, unencapsulated PD-treated devices retain 96% of their initial efficiency after 2000 h under nitrogen atmosphere, whereas control devices retain only 74%. Under ISOS-D-2I accelerated aging (65±5°C in N2), PD-treated devices show less than 5% PCE attenuation after 288 h, compared to ~30% for controls. This work provides a viable strategy for defect passivation in perovskite solar cells, enhancing both efficiency and stability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3654-5
Hydrogen production by photosynthetic green algae is an efficient biological process that utilizes light energy to convert water and carbon dioxide into clean and renewable energy. In this paper, we constructed a hybrid system combining graphitic carbon nitride (g-C3N4) and Chlorella pyrenoidosa (Chlorella), in which g-C3N4 serves as an extracellular electron source and Chlorella acts as a biological reactor for specific hydrogen production. In particular, the electronic structure of carbon nitride was optimized by means of hydrothermal alkalization and copper ion doping, expanded the light absorption range and enhanced the light response ability. g-C3N4, as an extracellular electron source, can provide electrons for Chlorella to improve hydrogen production performance which is 3.7 times that of bare Chlorella. The construction of a biological hybrid system is a feasible optimization strategy for the hybrid system to promote the synergistic effect of the hybrid system by regulating the properties of non-living components.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024083002
Selenium (Se) is an essential trace element for human health, and dietary intake through Se-rich crops is the primary route. However, total soil Se content does not directly reflect the bioavailability to plants, which depends largely on soil available Se. This study, conducted in Shipai Town, Longshan County, Hunan Province, used 1:50,000 land quality geochemical survey data to investigate factors influencing the Se bioaccumulation coefficient in maize kernels. Soil pH, CaO, and MgO were identified as significantly positively correlated with the bioaccumulation coefficient and were selected as proxies for soil available Se. A random forest (RF) model was developed to predict maize grain Se content and assess the feasibility of cultivating Se-rich maize in low-Se farmland. Results showed that although soil Se was deficient, 53.64% of maize grain samples met the Se-rich product standard (0.02–0.30 mg·kg−1). Compared with multiple linear regression, the RF model exhibited higher accuracy and reliability. The RF model predicted that 40.91% of farmland in the study area is suitable for natural Se-rich maize cultivation, representing a 25.86% increase over the area identified by soil total Se alone. This study provides a novel methodological framework for planting natural Se-rich maize in Se-deficient regions, validating the potential for such cultivation.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60647-0
Photoelectrochemical (PEC) water splitting offers a direct route to convert solar energy into clean hydrogen fuel. CuBi2O4, a p-type semiconductor with a bandgap of 1.5–1.8 eV, exhibits visible-light responsiveness and good stability, yet its performance is limited by high interfacial resistance and severe charge carrier recombination. This study introduces a CuO interlayer between fluorine-doped tin oxide (FTO) and CuBi2O4 to construct CuO/CuBi2O4 photocathodes, aiming to improve interfacial charge transfer. The optimized CuO/CuBi2O4-200 photocathode achieved a photocurrent density of −1.71 mA/cm² at 0 V vs. RHE, more than 3.5 times that of bare CuBi2O4. Incident photon-to-current efficiency (IPCE) at 365 nm reached ~13%, and the maximum applied bias photon-to-current efficiency (ABPE) was 0.17%. Water splitting experiments yielded 2.05 μmol/cm² of hydrogen, significantly surpassing the unmodified photoelectrode. Mechanistic studies indicate that the CuO layer establishes favorable band alignment, promotes hole transport toward the FTO substrate, and suppresses interfacial carrier recombination. This work demonstrates a simple and efficient interfacial engineering strategy, offering insights for the design of high-performance semiconductor-based PEC photoelectrodes.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010802
Ozone (O3) pollution is a prominent issue in the Guanzhong Plain, necessitating effective control of its precursors, particularly volatile organic compounds (VOCs). However, studies on VOC pollution characteristics at the county level are scarce. To investigate the summer VOC pollution characteristics and sources in high-altitude towns of the Guanzhong Plain, continuous monitoring of 53 typical VOC species was conducted at two sites in Changwu County, Xianyang City (elevation 1200 m). The spatiotemporal variations of ambient VOCs and their ozone formation potential (OFP) were analyzed, and source apportionment was performed using the Positive Matrix Factorization (PMF) model. Results showed that average total VOC (TVOCs) concentrations at the Changwu Government and Changwu Middle School sites were 60.04×10⁻⁹ and 83.28×10⁻⁹, respectively. Oxygenated VOCs (OVOCs) dominated, accounting for 55.14% and 62.91% of TVOCs, followed by alkenes, aromatic hydrocarbons, and halogenated hydrocarbons. Industrial sources contributed the most (43.2%) to VOC emissions in Changwu County, but site-specific differences were observed: the Government site was primarily influenced by solvent use (30.7%) and motor vehicles (19.1%), while the Middle School site was dominated by domestic sources (27.6%) and motor vehicles (20.0%). The average OFP values at the Government and Middle School sites were 258.84×10⁻⁹ and 378.04×10⁻⁹, respectively, with alkenes and OVOCs as the main contributors, originating from industrial emissions, solvent use, and biogenic sources. EKMA curves indicated that Changwu County was in a VOC-limited regime during the observation period, confirming the effectiveness of VOC control for ozone mitigation. These findings provide scientific guidance for local ozone management and offer a paradigm for precise ozone pollution control in county-level regions of the Guanzhong Plain.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605001
The lower reaches of the Yangtze River Basin, as a concentrated area of China's C5 petroleum resin industry, face critical bottlenecks in green and low-carbon transformation due to high-pollution, refractory wastewater and high carbon emissions. Traditional petrochemical wastewater treatment technologies suffer from low efficiency, high energy consumption, and insufficient resource utilization. This paper systematically analyzes the sources of wastewater in C5 petroleum resin production from principles and processes, and reviews research progress and carbon reduction potential of current technologies in three aspects: new materials, new equipment, and new processes. Integrated processes centered on efficient pretreatment, biological enhancement, and multi-technology coupling show significant advantages in improving treatment efficiency, reducing energy consumption and cost, and strengthening resource recovery. The study also prospects future research priorities for pollution and carbon mitigation through green technological innovation and intelligent upgrading, providing new solutions for 'near-zero discharge' and resource recycling of C5 petroleum resin wastewater, thereby promoting the green and low-carbon transformation of the petrochemical industry.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3933-9
The global cold chain consumes vast amounts of energy and emits greenhouse gases, while many regions lack proper refrigeration. To address this, we developed a dual-layer electrospun membrane (PZ-PML) for energy-free fruit preservation. The top PVDF-HFP/ZIF-8 layer offers 97.64% solar reflectance and 92.5% mid-infrared emissivity, providing 70 W/m2 radiative cooling. The bottom PAN/MIL-101/LiCl layer, with 2.18 g/g water uptake at 80% RH, delivers ~156 W/m2 evaporative cooling, lowering surface temperature by 6.1 °C under ~400 W/m2 irradiation. The membrane also shows ≥99% antibacterial efficiency against E. coli and S. aureus. Applied to strawberries, it reduced dehydration to 20.2% after 9 days, compared to 68.2% and 74.4% in controls. Additionally, it demonstrates durability, superhydrophobicity, and UV stability. This scalable solution offers energy-free fruit cooling, reducing postharvest losses while maintaining quality and safety.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509020
The AAOA-MBR (anaerobic-anoxic-oxic-anoxic membrane bioreactor) process is widely used in municipal wastewater treatment, but its multi-stage internal recirculation complicates sludge retention time (SRT) and carbon source distribution. This study systematically regulated three reflux ratios (R1: membrane tank to oxic tank; R2: oxic tank to anoxic I tank; R3: anoxic II tank to anaerobic tank) in a pilot-scale system (0.24 m3·d−1) to reveal their effects on nutrient removal and membrane fouling. When R1:R2:R3 = 300%:200%:100%, effluent COD, TN, TP, and NH3-N met discharge standards. Reducing R1 and R2, thereby decreasing total reflux ratio from R=6 to R=3, shortened SRT, which suppressed nitrifier accumulation and increased effluent COD and TN, but decreased TP. High-throughput sequencing of anoxic I and oxic tanks showed that denitrifying bacteria (Thauera and Ottowia) relative abundances decreased from 0.68% to 0.42% and 0.51% to 0.24%, respectively, while the phosphorus-accumulating organism Candidatus_Accumulibacter increased from 0.78% to 1.12%, enhancing phosphorus removal. Additionally, lowering R1 to 200% caused sludge accumulation in the membrane tank, exacerbating membrane fouling. Thus, internal recirculation ratios must be adjusted based on influent characteristics to balance nutrient removal and membrane performance.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606006
Chitosan-based microsphere composites have attracted considerable attention for phosphorus adsorption due to their facile preparation, low cost, environmental friendliness, and high uptake capacity. This review summarizes the physicochemical properties and preparation methods of chitosan microspheres for phosphate removal, outlines common modification strategies to enhance adsorption capacity, and discusses their applications in aqueous environments. Adsorption mechanisms, regeneration, and resource recovery of spent microspheres are analyzed. Challenges and recommendations are proposed, including streamlined preparation, enhanced phosphorus recovery, removal of multiple phosphorus forms, and practical implementation. The review aims to guide the development of high-performance chitosan-based microspheres for phosphorus removal.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3989-4
Organic-inorganic hybrid metal halides (OIMHs) based on Cu(I) ions exhibit broad application prospects in stimulus-responsive luminescent materials due to their rich structural diversity and highly adjustable electronic states. However, achieving sensitive and broad-temperature-range thermal responses remains a significant challenge. Here, we synthesize a zero-dimensional warm white-light emitting OIMH, MPC-W ((C9H20N2O)4(Cu2I4)(Cu2I6)(H2PO2)2), using 4-morpholinopiperidine (4-MP) and CuI. MPC-W features hybrid structures of [Cu2I4]2− and [Cu2I6]4−. The coexistence of three luminescent mechanisms—organic cluster luminescence (CL), self-trapped exciton (STE) emission of [Cu2I6]4−, and cluster-centered (CC) state luminescence of [Cu2I4]2−—endows MPC-W with temperature- and excitation-wavelength-dependent dynamic luminescence. From 77 to 297 K, the luminescence color continuously tunes from blue to cyan, green, yellow-green, and white. In the range of 217–463 K, MPC-W exhibits abnormal luminescence enhancement with increasing temperature. Upon chemical stimuli, MPC-W reversibly transforms into blue-emitting MPC-B ((C9H20N2O)Cu2I4) and yellow-emitting MPC-Y ((C9H18N2O)7Cu8I8). These dynamic luminescent properties position MPC-W for applications in temperature sensing, optical anti-counterfeiting, and password locks. This work provides new insights for developing wide-temperature-responsive multifunctional intelligent luminescent materials.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511043
Zero-valent iron (ZVI) suffers from surface passivation and low electron utilization in reductive removal of nitrobenzene (NB). To address these issues, a ball-milled iron/digestate biochar composite (BM-Fe/DBC) was prepared and compared with a physically mixed counterpart (PM-Fe/DBC). Characterization revealed that ball milling tightly embedded ZVI particles into the carbon matrix, forming Fe–C chemical bonds and a strong interfacial coupling structure that established efficient electron transfer channels. This structure significantly enhanced the micro-galvanic effect between iron and carbon, yielding superior reduction performance across a wide pH range (3–9). Under optimal conditions (Fe:C mass ratio 2:1, dosage 1.0 g·L−1, pH 5), BM-Fe/DBC achieved 79.9% NB removal, and the generation of aniline (AN) was 1.85 times that of PM-Fe/DBC. Mechanistic studies indicated that the intimate Fe–C interfacial coupling promoted sustained ZVI corrosion and enhanced the production of indirect reducing species, including adsorbed Fe(II) and atomic hydrogen (H*). Electrochemical analyses showed that BM-Fe/DBC exhibited a lower corrosion potential, a higher corrosion current density (approximately 2.15 times higher), and lower charge transfer resistance, kinetically confirming its superior electron transfer capability. These findings reveal that constructing strong interfacial coupling in iron–carbon composites via mechanochemical methods can effectively overcome key limitations of ZVI in reduction reactions, providing a theoretical basis and practical pathway for designing high-performance water treatment materials.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202408057
Urban waterlogging, exacerbated by climate change and rapid urbanization, poses increasing risks, particularly in coastal low-lying areas with dense river networks. This study simulated waterlogging in the Shajing River drainage area of the Maozhou River basin, Shenzhen, using the SOBEK hydrodynamic model. Under a 5-year return period rainfall, 47 manholes overflowed and 31.29% of stormwater pipes operated at full capacity. Twelve waterlogging-prone points were identified: eight due to insufficient drainage capacity and five due to river backflow from low elevation. Two optimization schemes were compared: enlarging pipe diameters and implementing Low Impact Development (LID) measures. Pipe enlargement reduced overflowing manholes by 32 and full-flow pipe length by 20%, effectively decreasing surface ponding. LID measures reduced overflowing manholes by only 4 and full-flow pipe length by 1.5%, but decreased maximum flooding depth by nearly 1 m, alleviating drainage system burden. The study highlights the complex causes of coastal urban waterlogging, especially river backflow under tidal influence, and recommends considering sea-level rise and storm surge in drainage design. The findings provide valuable references for attributing waterlogging causes and planning drainage network upgrades in coastal cities.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60656-1
Under the carbon neutrality strategy, biomass boilers have emerged as key facilities for renewable energy utilization, yet are characterized by low-concentration SO2 emissions. Ca-based dry desulfurization presents a promising technology for biomass boiler flue gas purification due to its compact structure, low capital investment and simple operation and maintenance. However, it is generally limited by the low adsorbent utilization and insufficient desulfurization efficiency. Herein, this study developed a novel Ca-Mn composite adsorbent through a synergistic strategy integrating F127 surfactant to optimize dispersion and Mn loading to enhance oxidation efficiency. The resulting adsorbent not only significantly increased the breakthrough sulfur capacity of the Ca-based material but also markedly improved the synergistic removal of Hg0. It was demonstrated that the introduction of Mn elements and F127 effectively suppressed the agglomeration of Ca(OH)2 crystallites and induced an oxygen vacancy-rich structure, while simultaneously optimizing the pore structure of the adsorbent. The modified adsorbent exhibited the enlarged specific surface area and pore volume, which favored to enhance the reaction mass transfer and effectively prevent the pore blockage and coverage of active sites by desulfurization products. The Mn sites and oxygen vacancies formed catalytic centers, which not only accelerated the desulfurization reaction by promoting SO2 oxidation but also enabled the adsorbent to couple with Hg0 catalytic oxidation functionality. Consequently, the simultaneous removal of SO2 and Hg0 was significantly enhanced on the Ca-Mn composite adsorbent.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025041409
High-entropy alloys (HEAs) have emerged as promising catalytic materials for organic wastewater treatment owing to their unique catalytic activity, structural stability, and corrosion resistance. This review systematically elaborates the physicochemical properties of HEAs and their multi-path degradation mechanisms, with emphasis on Fenton reactions, photocatalysis, and tribocatalysis. The influence of mainstream preparation techniques—mechanical alloying, arc melting, gas atomization, and impregnation adsorption—on catalytic performance is critically compared. To overcome practical bottlenecks such as low powder recovery and rapid active-site deactivation, synergistic optimization strategies including metal doping, morphological modification, and composite engineering are proposed. The review identifies key challenges in enhancing degradation efficiency, scaling up production, and designing composite materials, and outlines future research directions for HEAs in wastewater treatment. This work provides a theoretical foundation for developing efficient and stable HEA-based environmental catalysts.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042203
Cadmium (Cd) accumulation in crops is influenced by complex, crop-specific factors, posing challenges for the safe utilization of soils with elevated Cd levels. This study focused on a region with anomalously high soil Cd in northern Longshan County, Hunan Province, China. We systematically collected and analyzed Cd concentrations in the edible parts of lily (Lilium spp.) and maize (Zea mays L.), along with corresponding root-zone soil properties including Cd content, pH, and oxide levels. The bioconcentration factors (BCF-Cd) for lily and maize were compared, and their controlling factors were identified. Using random forest with hyperparameter optimization, optimal predictive models for BCF-Cd were developed for each crop. Results showed that lily BCF-Cd was significantly higher than that of maize. Key factors influencing BCF-Cd in both crops included soil pH, manganese (Mn), organic matter (OM), and the weathering-leaching coefficient (ba). Feature importance analysis identified soil pH as the most critical factor. Based on model predictions, a zoning scheme for safe arable land utilization was proposed to maximize land productivity while ensuring the medicinal safety of lily and food safety of maize. This study provides scientific support for enhancing food security and optimizing land resource use.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608024
Microbial remediation is a widely used technology for treating chromium pollution in groundwater. This study conducted a bibliometric analysis of 441 papers from the Web of Science Core Collection (2010–2024) using CiteSpace, VOSviewer, and Pajek. The publication trend increased over the period, with three developmental stages identified: early (2010–2016) focusing on basic treatment methods, intermediate (2017–2019) on intrinsic mechanisms, and recent (2020–2024) on process optimization. Biological adsorption and reduction were identified as the primary mechanisms. Correlation and principal component analyses of environmental factors (temperature, pH, initial Cr concentration, reaction time) revealed temperature as the key factor affecting remediation efficiency. The removal efficiencies and mechanisms of various dominant bacterial strains were summarized to guide strain selection. Future research should focus on microbial community synergy, nanomaterial integration, and environmental optimization to enhance remediation efficiency.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3843-9
Lignocellulose-based electromagnetic interference (EMI) shielding materials are gaining prominence across multiple sectors, driven by the growing EMI issues associated with rapid advances in communication technologies and electronic devices. These materials have demonstrated significant superiority over traditional EMI shielding solutions, which are often hampered by high cost and environmental concerns. This review emphasizes the excellent potential of lignocellulose as a cost-effective and flexible alternative to deliver the hierarchical structures and functional properties that qualify it for EMI shielding applications. The underlying EMI shielding mechanisms are then elucidated, with a focus on the benefits conferred by lignocellulose in such material systems. Furthermore, typical fabrication strategies for lignocellulose-based EMI shielding materials are comprehensively summarized, along with a discussion of their emerging applications in diverse scenarios. Finally, the challenges encountered in developing lignocellulose-based EMI shielding materials and their significant prospects for future boosting high-performance design and application are also outlined. The insights presented herein are expected to promote the development of efficient and green lignocellulose-based EMI shielding materials that meet the evolving demands of modern society.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3978-0
All-polymer solar cells (all-PSCs) are promising for flexible and wearable electronics due to their excellent stability and mechanical stretchability. However, achieving high performance remains challenging due to difficulties in controlling the morphology of polymer blend films. In this study, a novel polymer donor, PBDTF-DTP, incorporating a weak electron-withdrawing yet large-dipole-moment dithienylphthalimide (DTP-2T) unit, was rationally designed and synthesized for ternary all-PSCs. Introducing PBDTF-DTP as a guest donor enables complementary light absorption and deepens the highest occupied molecular orbital level, simultaneously improving short-circuit current density (J_SC) and open-circuit voltage (V_OC). The large dipole moment of DTP-2T increases the dielectric constant, suppressing non-radiative energy loss and further boosting V_OC. Notably, PBDTF-DTP exhibits a relatively higher molecular electrostatic potential than the host donor, effectively tuning compatibility with both polymer donor and acceptor, regulating blend morphology, and promoting formation of a nanoscale fibrillar network. This optimized morphology facilitates efficient charge generation and transport while suppressing charge recombination. Consequently, ternary all-PSCs based on PM6:PBDTF-DTP:PYIT achieve a synergistic enhancement in J_SC, V_OC, and fill factor, yielding a remarkable power conversion efficiency of 18.01%, significantly higher than that of binary PM6:PYIT devices (15.51%). This study demonstrates that combining electrostatic potential optimization with a ternary strategy provides an effective approach to regulate morphology and achieve high-efficiency all-PSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4040-0
High-performance organic second-order nonlinear optical (NLO) crystals face a persistent challenge: molecular designs that enhance hyperpolarizability often crystallize into centrosymmetric or nonpolar arrangements, suppressing bulk second-order response, while simultaneously reducing optical bandgaps, enforcing a trade-off between nonlinearity and transparency. We report a chirality-driven polar lattice engineering strategy that couples molecular asymmetry with directional intermolecular interactions to promote polar ordering. A binaphthyl-based chromophore (S-3) crystallizes in the polar space group P2₁, exhibiting strong second-harmonic generation (~3.53 × KDP), wide transparency (3.91 eV), phase-matchable birefringence (Δn = 0.15), high laser damage threshold (742.6 MW cm⁻²), and thermal stability up to 210 °C. Theoretical calculations reveal a 69% enhancement in first-order hyperpolarizability (β_tot) relative to the unfunctionalized derivative, with a net intramolecular electron transfer of 0.16 e⁻ from the chiral scaffold to the benzoate acceptor. Crucially, enantiomeric crystals exhibit identical NLO responses, confirming that bulk nonlinearity is governed by engineered lattice polarity, not molecular handedness. This work establishes chirality as an active tool for crystal engineering and provides a general design paradigm for high-performance organic NLO materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4129-y
Therapeutic biosynthesis is a promising strategy for precision cancer therapy, yet achieving controlled synthesis of abiotic materials within tumors remains challenging. Here, we report a “dual lock-and-key” system for tumor-specific intracellular synthesis. The precursor, termed “dual-lock,” is activated by two endogenously overexpressed enzymes—azoreductase (AzoR) and nitroreductase (NTR)—acting as “dual keys” in target cancer cells. This activation triggers a condensation reaction that produces fibrous mesh covalent organic polymers (Fm-COPs) in situ. Synthesized Fm-COPs effectively disrupt the cytoskeleton, inhibiting cell migration and invasion while inducing apoptosis. In vivo studies demonstrate that this strategy achieves specific tumor enrichment and deep penetration, leading to significant tumor growth inhibition (tumor inhibition rate >70%) without systemic toxicity, as evidenced by stable body weights and normal histopathology. The dual enzyme-responsive mechanism ensures high selectivity, and the small-molecule precursors facilitate efficient tumor penetration. This work presents a next-generation approach for high-precision cancer therapy, offering a biocompatible and autonomous strategy for intracellular synthesis.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-024-3300-6
Photothermal therapy (PTT) is limited by heat shock protein (HSP) upregulation and mitochondrial-encoded thermoresistance in tumor cells. This study reports PtRhMo/Rh multi-metal nanozymes synthesized via a one-step method for cascade enzymatic therapy and enhanced PTT. The nanozymes exhibit a photothermal conversion efficiency of 55.6% and multiple enzyme-like activities: catalase (CAT), oxidase (OXD), peroxidase (POD), glutathione peroxidase (GPx), and NADH oxidase (NOX). These activities generate reactive oxygen species (ROS) and deplete NADH, disrupting the electron transport chain (ETC) and causing mitochondrial damage. This downregulates HSP70, sensitizing tumors to heat. In vivo biocompatibility tests at 400 ppm showed no hemolysis and no significant pathological changes in major organs. Hematological parameters remained stable. The synergistic approach directly kills tumor cells and weakens thermoresistance, offering a promising strategy for clinical translation.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-024-3283-y
Structure modulation at multiscale is critical for optimizing electromagnetic wave absorption (EWA) in fiber-reinforced composites. This study employs two SiC fibers with distinct resistivities: L-fiber (~3 Ω·cm) and H-fiber (~7×10^5 Ω·cm). To tailor impedance, BN single coating and SiO2/BN dual-coating were applied to L-fibers. Unidirectional prepregs were stacked in various sequences to fabricate composites. Results demonstrate that both fiber coatings and stacking architecture significantly affect EWA performance. Computational optimization guided the design, yielding stacked composites with reflection loss (RL) below −10 dB across the entire X-band (8.2–12.4 GHz) and Ku-band (12.4–18.0 GHz). Notably, surface coatings on L-fibers substantially widen the thickness range over which stacked composites maintain excellent performance. Dual-coating outperforms single coating in broadening this available thickness range. These findings provide a robust strategy for engineering high-performance EWA composites through multiscale structural control.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3412-2
Elucidating the fundamental mechanisms underlying Cu reconstruction is paramount for the rational design of catalysts that meet the stringent activity, selectivity, and durability requirements for industrial-scale CO2/CO electroreduction (CO2RR/CORR). While both dissolution-redeposition and atomic migration pathways have been proposed, the operational conditions dictating their relative dominance remain poorly understood. Through quasi in situ Cu+ detection and in situ atomic force microscopy (AFM), we reveal a striking mechanistic dichotomy: Cu reconstruction during CO2RR occurs strictly in the presence of Cu+, whereas CORR-induced reconstruction proceeds independently of Cu+ species. These findings suggest that Cu reconstruction in CO2RR follows a dissolution-redeposition mechanism induced by oxidative radicals, while atomic migration emerges as the dominant pathway in CORR. Density functional theory calculations further demonstrate that adsorbed *CO intermediates reduce Cu–Cu bond strength, creating metastable surface configurations that promote Cu atomic migration. The investigation extends to broader metal catalysts (e.g., Ag, Au, Zn) and highlights the interplay between adsorbed species, interfacial environments, and applied potentials. Our findings establish a unified framework for understanding Cu restructuring dynamics, providing a paradigm for strategically engineering metal catalysts through controlled reconstruction, advancing the rational design of CO2RR/CORR systems.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3422-1
Hollow noble metal microspheres are constrained by intrinsic brittleness, which limits their practical deployment in catalysis, electronics, and chemical detection. This study reports a scalable fabrication route to vesicle-like polystyrene-silver (SPS@Ag) composite microspheres with enhanced toughness. Uniform polystyrene (PS) microspheres of approximately 1.5 μm diameter were synthesized via dispersion polymerization, sulfonated to introduce surface sulfonate groups, and sensitized with Sn2+ ions to facilitate electrostatic adsorption. Subsequent in situ chemical reduction of [Ag(NH3)2]+ yielded well-defined core-shell SPS/Ag composite microspheres with tunable shell thickness controlled by the number of reduction cycles. Removal of the PS core using DMF produced hollow vesicle-like SPS@Ag microspheres. The incorporation of SPS within the silver membrane confers exceptional toughness, mitigating the collapse typically observed during template removal. Surface-enhanced Raman scattering (SERS) performance was evaluated using rhodamine 6G (R6G) as a probe molecule. The vesicle-like SPS@Ag microspheres exhibited a significant increase in Raman enhancement factor compared to their core-shell counterparts, demonstrating their potential as highly efficient SERS substrates for analytical chemistry, sensing technologies, and catalytic processes.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3533-1
Two-dimensional metal halide perovskites (2D MHPs) exhibit strong excitonic effects and structural tunability, but their photoelectric properties are dictated by exciton dynamics. This study investigates halogen doping in PEA2Pb(Br1−xClx)4, revealing a systematic spectral evolution from blue to white-light emission as Cl content increases. Temperature-dependent photoluminescence and lattice distortion analysis indicate that Cl doping induces subtle structural perturbations, switching between extrinsic and intrinsic self-trapped exciton (STE) states. Below x = 0.2, intrinsic STE formation is enhanced via lattice softening; above x = 0.2, defect-assisted trapping pathways dominate. A dual-channel trapping model, validated by temperature-activated detrapping kinetics and transient absorption spectroscopy, accounts for the observed spectral broadening. These findings provide a defect engineering strategy for tailoring emission in low-dimensional hybrid perovskites, with implications for white-light LEDs and scintillators.