SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4420-7
Cu2-xSe is a leading p-type thermoelectric material owing to its phonon-liquid electron-crystal (PLEC) behavior, yet the atomic-scale mechanisms governing Cu+ migration remain unresolved. This study employs in situ high-resolution neutron diffraction coupled with maximum entropy method (MEM) analysis to map the temperature-dependent evolution of Cu+ nuclear density in β-Cu2Se and β-Cu1.95Se. At 398–423 K, intra-tetrahedral Cu 8c ↔ 32f <111> hopping emerges, with isosurface values of 0.505 fm Å-3 for β-Cu2Se and 0.484 fm Å-3 for β-Cu1.95Se. Above 448 K, inter-tetrahedral pathways form via Cu 32f ↔ 32f <100> or 32f ↔ 4b ↔ 32f <111> migration, as revealed by line scans along [1̅11̅] up to 723 K. The presence of Cu vacancies (x = 0.05) alters the onset and connectivity of these pathways, directly impacting phonon scattering and electron transport. These findings establish a structural basis for controlling Cu+ mobility, offering a rational route to mitigate Cu precipitation and enhance zT stability beyond 1.5 at 900 K. The work bridges microstructural dynamics and thermoelectric performance, providing critical guidance for defect engineering in superionic thermoelectrics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4416-8
Copper(I)-based carbene-metal-amide (CMA) emitters offer an earth-abundant alternative to precious-metal phosphors for organic light-emitting diodes (OLEDs), yet efficient green emission remains scarce due to limited π-extension and unbalanced charge-transfer characteristics of N-heterocyclic carbene (NHC) ligands. This work introduces a pyrimidine-fused NHC ligand (CF3PMI) with balanced π-accepting ability, synthesized via a one-pot protocol in good yields. The resulting Cu(I)-CMA complex CF3PMI-BFCF3 exhibits green thermally activated delayed fluorescence (TADF) in doped thin films, with a photoluminescence quantum yield (PLQY) of 90% and a short emission lifetime of 1.16 μs. A vacuum-deposited OLED achieves green electroluminescence centered at 514 nm with an external quantum efficiency (EQE) of 22.7%. Furthermore, a hyperfluorescent OLED employing CF3PMI-BFCF3 as a sensitizer delivers an EQE of 21.8%, green emission at 537 nm, and a narrow full width at half maximum (FWHM) of 30 nm. These results establish a viable molecular design strategy for high-performance green-emitting Cu(I)-based TADF materials and provide a convenient synthetic route for Cu(I)-CMA emitters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4250-0
Shape memory polymer (SMP)-based transfer printing offers a promising route for heterogeneous integration of flexible electronics, yet non-contact release reliability remains a critical bottleneck. This study systematically investigates the influence of pickup heating modes—localized versus global—on the release yield and energy-delivery mechanisms through combined experiments and finite element simulations. The localized heating mode concentrates strain energy at the interface, enabling controlled chip ejection with high yield, whereas global heating dissipates energy, leading to release failure. Quantitative analysis reveals that localized heating achieves a release yield of 100% under optimized conditions, compared to near-zero for global heating. The ejection velocity under localized heating is higher, which may induce chip bouncing on the receiver substrate, affecting transfer accuracy; however, this can be mitigated by adjusting release gap and laser parameters. The findings establish a theoretical framework for energy pathway design, providing guidelines for achieving high-yield, accurate non-contact release in laser-induced transfer printing. This work advances the practical application of SMP-based transfer printing for micro-LED displays and flexible electronics, addressing a key manufacturing bottleneck.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4112-6
Radiostrontium remediation is crucial for ecological protection and sustainable development of nuclear energy. However, efficient removal of 90Sr from complex radioactive liquid waste, especially under acidic conditions, remains challenging due to material instability and intense proton competition. Herein, the rapid and highly selective capture of Sr2+ in neutral and even acidic solutions has been achieved by a layered potassium phosphatoantimonate KSbP2O8 with excellent radiation and thermal stability. Under neutral conditions, it possesses high maximum adsorption capacity (qmSr = 110.25 mg g−1), rapid adsorption kinetics (the removal rate (RSr) of 91.54% within 30 min), and excellent selectivity for Sr2+, and facile regeneration. Particularly, even under acidic conditions (pH 2.0), KSbP2O8 still maintains excellent Sr2+ removal capacity (qmSr = 79.38 mg g−1), fast kinetics, and high selectivity. A mechanism study by multiple characterizations reveals that the efficient Sr2+ removal of KSbP2O8 mainly stems from ion exchange between Sr2+ and interlayer K+ in KSbP2O8, which is attributed to the synergy between the Sb5+-induced Brønsted acidity and the high charge density of the anionic framework. This study demonstrates the exceptional capability of phosphatoantimonates to selectively capture Sr2+ under acidic conditions, highlighting the potential of phosphatoantimonates as effective scavengers for radiostrontium remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3536-5
Nanomaterial-based optical biomedicine and devices have attracted significant attention for tumor diagnosis and treatment, yet their application in tumor ablation is often hindered by limited functional integration and concerns over excessive radiation exposure. In this study, we address these challenges by developing a multifunctional fiber probe based on lanthanide-doped nanoparticles, featuring decoupled modules for localized heating and optical thermometry. This design enables synergistic therapy under near-infrared (NIR) laser irradiation. Beyond achieving precise photothermal ablation and real-time temperature monitoring, we uncovered a unique phenomenon: the generation of reactive oxygen species (ROS) by these nanoparticles under NIR laser excitation, even in the absence of traditional photosensitizers. Through a combination of experimental and computational approaches, we elucidated the physical mechanisms underlying ROS generation in wide-bandgap lanthanide nanoparticles. Leveraging these insights, we constructed an all-optical fiber system capable of simultaneous precise thermal control and photodynamic therapy. Our findings offer valuable guidance for the development of advanced optical nanomaterials and devices for effective tumor treatment, both in vivo and in vitro.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3602-1
Solid-state lithium batteries (SSLBs) are promising next-generation energy storage systems due to their high safety and energy density. However, poor low-temperature performance of solid-state electrolytes remains a critical challenge. Here, we present a facile and scalable approach for synthesizing a low-temperature-resilient polymer electrolyte based on ethylene-vinyl acetate (EVA), leveraging its unique molecular structure for enhanced lithium-ion transport. The EVA polymer electrolyte (EPE) demonstrates a high ionic conductivity of 5.13×10−4 S cm−1 at room temperature and retains a remarkable conductivity of 2.72×10−5 S cm−1 at −40 °C. This superior performance is attributed to the synergistic interaction between the ester functional groups of EVA and lithium salts, which reduces the ion dissociation energy barrier and facilitates efficient ion migration. The EPE enables stable lithium plating/stripping cycling for over 3000 h at −40 °C and supports long-term cycling of LiFePO4-based full cells at −40 °C for over 900 cycles. This work highlights the potential of cost-effective, scalable EPEs for next-generation SSLBs, particularly in extreme environmental conditions.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3615-1
Stretchable electronics are pivotal for bio-integrated devices, soft robotics, and wearables, yet their development is constrained by single-layer architectures that limit integration density and by mechanical mismatch between rigid components and soft substrates, which curtails service life. Here, we introduce a LEGO-like modular assembly strategy to construct multilayer three-dimensional (3D) stretchable electronics. Electronic components (ECs) and self-healing polyurethane (SPU) substrates patterned with liquid metal (LM) circuits serve as the modular blocks. This design simplifies fabrication and markedly enhances 3D integration density. The combination of LM circuits and self-healing elastic substrates enables devices to withstand diverse deformations and to autonomously heal after mechanical damage. Notably, the devices can undergo multiple recycling and reuse cycles without significant performance loss. This methodology offers a new paradigm for advanced flexible electronics, addressing critical bottlenecks in integration density, mechanical robustness, and sustainability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3657-9
Perovskite/silicon tandem solar cells (TSCs) have achieved power conversion efficiencies (PCE) up to 34.9%, surpassing the Shockley-Queisser limit of single-junction devices. The interconnection layer (ICL) critically bridges top and bottom subcells, enabling charge carrier recombination. Conventional indium oxide (In2O3)-based TCOs suffer from high-energy ion bombardment during sputtering, damaging amorphous silicon subcells and reducing open-circuit voltage (VOC) and fill factor (FF). Additionally, indium scarcity and cost necessitate indium-free alternatives. Here, we introduce a highly degenerate indium-free samarium-doped cadmium oxide (CdO:Sm) TCO as the ICL for perovskite/SHJ TSCs, deposited via low-damage reactive plasma deposition (RPD). The ultrathin CdO:Sm film (~3 nm) exhibits average transmittance of 85% (400–1200 nm) and 90% (800–1200 nm), enabling efficient near-infrared absorption in the bottom subcell. High doping concentration and mobility ensure excellent electrical conductivity. The low work function (4.04 eV) of CdO:Sm facilitates carrier tunneling and efficient recombination. Devices employing CdO:Sm ICL achieved approximately 1% higher efficiency compared to those with indium-based TCO ICLs. Detailed characterization including contact resistivity (1.68 mΩ cm2), conductive atomic force microscopy, Kelvin probe force microscopy, and photoluminescence quenching confirm enhanced carrier transport and extraction. This work demonstrates a viable indium-free ICL for high-efficiency perovskite/SHJ TSCs, addressing both performance and sustainability challenges.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507051
This study investigated the dynamic characteristics and recovery of ammonia emissions from a growing-finishing pig house in Yanshi District, Luoyang City, Henan Province, China. High-sensitivity electrochemical sensors and an ammonia absorption recovery device were employed for continuous monitoring and treatment of exhaust air. The results revealed periodic fluctuations in ammonia emission concentrations, strongly correlated with indoor temperature and humidity. Over the entire monitoring period, the average daily ammonia concentration in exhaust air was 9.852 mg·m−3, below the national emission limit of 25 mg·m−3. However, during high-temperature periods (>30 °C), localized concentrations reached 38.36 mg·m−3. Humidity, particularly from spray cooling, temporarily suppressed ammonia volatilization, but its effect was modulated by temperature. Total ammonia emitted during the study was 1380.4 kg, with an average per-pig emission rate of 0.034 kg·d−1. After treatment with the exhaust gas absorption device, the average daily ammonia concentration dropped to 0.437 mg·m−3, achieving a mean recovery efficiency of 93.5%. These findings demonstrate that controlling environmental factors and employing external air absorption devices can significantly reduce ammonia emissions, offering a viable pathway for mitigating nitrogen pollution from livestock operations and promoting resource recovery.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507057
This study presents a novel electrochemical sensor for the rapid detection of trace lead ions (Pb(II)) in water, utilizing a rod-shaped bismuth-based electrode. The electrode was fabricated by modifying a glassy carbon electrode (GCE) with basic bismuth nitrate [Bi6O5(OH)3](NO3)5·3H2O, synthesized via a chemical precipitation method. The sensor was characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), electron probe microanalysis (EPMA), and energy-dispersive X-ray spectroscopy (EDS), confirming the rod-like morphology and composition. Electrochemical detection was performed using differential pulse voltammetry (DPV) in a 0.1 mol·L−1 NaAc-HAc buffer (pH 4.3). The sensor exhibited a linear detection range for Pb(II) from 1 to 90 μg·L−1, with a detection limit of 0.34 μg·L−1 and a sensitivity of 106 μA·(μmol·L−1)−1. The electrode demonstrated excellent anti-interference capability and reproducibility. Recovery tests in real water samples (tap water and campus lake water) yielded high recovery rates, indicating practical applicability. This work provides a simple, cost-effective, and reliable method for monitoring trace Pb(II) in environmental water, particularly relevant for public swimming pools and similar aquatic facilities.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112804
The rapid dissemination of antibiotic resistance genes (ARGs) in aquatic environments poses serious threats to public health and environmental safety under the 'One Health' framework. Nanoplastics (NPs), as co-occurring pollutants, can exacerbate ARG risks by promoting horizontal gene transfer (HGT), yet the influence of different functional groups on extracellular ARG (eARG) transformation remains unclear. This study investigated the effects of carboxy-modified polystyrene NPs (PS-COOH) and amino-functionalized polystyrene NPs (PS-NH2) compared to unmodified polystyrene NPs (PS) on the transformation of the extracellular resistance plasmid IE-V1955 (carrying an ampicillin resistance gene) into Escherichia coli DH5α. Results showed that PS-COOH exposure promoted plasmid transformation similarly to PS, with effects increasing over 0.1–20 mg·L−1. Low concentrations (0.1–0.5 mg·L−1) of PS-NH2 also enhanced transformation, with stronger effects than PS-COOH at equal doses, whereas high concentrations (1–20 mg·L−1) inhibited it. Mechanistically, PS-COOH (0.1–20 mg·L−1) and low PS-NH2 induced intracellular reactive oxygen species (ROS), increased cell membrane permeability, elevated the protein-to-polysaccharide ratio in extracellular polymeric substances (EPS), and promoted biofilm formation, thereby facilitating transformation. High PS-NH2 concentrations caused excessive ROS leading to cell lysis and formed aggregates with plasmids larger than membrane pores, blocking uptake. These findings provide a theoretical basis for assessing the combined environmental health risks of NPs and ARGs.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112102
Based on the 2022 activity data of non-road mobile sources in Hebei Province, this study employed the emission factor method recommended by the Guidelines to estimate emissions of CO, HC, NOx, PM2.5, PM10, and SO2. A comprehensive emission inventory was established, followed by spatial and uncertainty analyses. Scenario analysis, aligned with the 14th Five-Year Plan policies, was used to project emissions for 2030. The results indicate that non-road mobile sources in Hebei emitted 76.1×10^3 t of CO, 20.6×10^3 t of HC, 164.0×10^3 t of NOx, 8.5×10^3 t of PM2.5, 9.0×10^3 t of PM10, and 2.4×10^3 t of SO2. Agricultural machinery was the dominant contributor to CO, HC, PM2.5, and PM10, accounting for over 60.0% of CO emissions. Railway locomotives were the primary source of NOx, contributing 50.9%. For SO2, agricultural machinery and railway locomotives contributed 39.0% and 44.4%, respectively. The highest emitting cities were Tangshan (21.3%), Shijiazhuang (15.7%), Cangzhou (11.6%), and Handan (11.6%). Ship emissions were concentrated in Tangshan Port; civil aviation emissions were mainly in Shijiazhuang, Tangshan, Qinhuangdao, and Handan; railway emissions were distributed in Shijiazhuang, Baoding, and Handan. Under the updated emission standard scenario, NOx and PM10 emissions in 2030 could be reduced by approximately 35.0%. The phase-out of old machinery yielded the largest reduction in CO (36.0%), while both electrification and phase-out scenarios significantly impacted HC emissions.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60616-5
CuZnAl (CZA) is a classic industrial catalyst for methanol synthesis from syngas, but its catalytic performance for CO2 hydrogenation to methanol is suboptimal. The catalytic mechanism of Cu species in CZA remains challenging. This study systematically investigates the valence state changes of active Cu species in CZA catalysts and their influence on catalytic performance by modifying catalysts with varying amounts of electron donor K, thereby identifying the catalytic function of Cu species with different valence states. H2-TPR, XPS, and HR-TEM characterizations reveal that highly dispersed K species supported on CZA catalysts inhibit the reduction of CuO, resulting in a small amount of Cu2O active species being produced under reaction conditions, thus causing a decrease in catalytic activity. Furthermore, XRD and Cu LMM spectra show that the proportion of Cu0 in K-modified CZA catalysts increases with K loading, but a higher proportion of Cu0 species on the surface obviously promotes the reverse water gas shift (RWGS) reaction. According to the results of in situ infrared spectroscopy, CZA catalyst follows the reaction pathway mediated by HCOO* in the hydrogenation of CO2 to methanol.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.226111
Efficient capture of the greenhouse gas nitrous oxide (N2O) is critical for climate change mitigation and resource recovery. In this study, two guanidinium-based hydrogen-bonded organic frameworks (HOFs) with pyridyl nitrogen site isomerism, namely G-5,5'-BPyDC and G-4,4'-BPyDC, were constructed using 2,2'-bipyridine-5,5'-dicarboxylic acid and 2,2'-bipyridine-4,4'-dicarboxylic acid as ligands. The effects of ligand structure on hydrogen-bonded network, pore environment, and N2O/N2 adsorption separation performance were systematically investigated via single-crystal X-ray diffraction, thermogravimetric analysis, Hirshfeld surface analysis, and gas adsorption experiments. Both frameworks are built via N-H...O hydrogen bonds. The asymmetric unit of G-5,5'-BPyDC contains two methanol molecules, resulting in larger free volume and surface area compared to G-4,4'-BPyDC, which exhibits more compact packing. Both materials show decomposition temperatures above 290°C, indicating good thermal stability. Hirshfeld surface analysis reveals that the total contribution of O-H/H-O and N-H/H-N hydrogen bonds in G-5,5'-BPyDC (32.0%) is higher than that in G-4,4'-BPyDC (29.7%). At 25°C and 4.0 MPa, the N2O adsorption capacity of G-5,5'-BPyDC is 2.32 mmol/g, surpassing that of G-4,4'-BPyDC (2.02 mmol/g). IAST calculations show that the selectivities of G-5,5'-BPyDC for N2O/N2 (50:50 and 10:90) mixtures reach 29.26 and 111.32, respectively, significantly superior to those of G-4,4'-BPyDC (6.61 and 17.03). Pyridyl nitrogen site isomerism effectively optimizes N2O/N2 adsorption and separation by modulating pore polarity and hydrogen-bonded network, offering a new strategy for isomer design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3814-2
Micro-structured surfaces have attracted increasing attention due to their great potential applications. However, it is still a challenge to continuously fabricate micro-structured surfaces based on thermoplastics by a facile, low-cost, and environmentally-friendly method. Herein, with the help of the extrusion molding method and an elaborately designed mold, micro-grooved fiber (MGF) based on high-density polyethylene (HDPE) is continuously prepared. Theoretically, infinitely long MGFs with feature sizes down to a few microns can be efficiently fabricated because of the continuous fabrication characteristic of the melt extrusion method. Interestingly, left- and right-handed micro-grooves with different helix angles can be produced by applying twisting at the die exit, and the macroscopically MGF springs can be further fabricated via a self-designed three-dimensional helical enwind device. By regulating wettability, MGF can achieve liquid self-transport on predefined paths. In addition, MGF fabric exhibits rapid evaporation behavior, whose evaporation rate is about 4 times higher than that of the Smooth fiber (SMF) fabric and 2 times higher than that of the most popular commercial quick-drying fabric (i.e., Cool-max fabric). This work proposes a facile and environmentally-friendly method for continuously preparing low-cost and flexible MGF, opening a new pathway to develop fiber-based microfluidic systems following the concept of "functionalized processing for thermoplastics".
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60618-9
Aromatic hydrocarbons, essential chemical feedstocks for fuels, synthetic fibers, and pharmaceuticals, are predominantly derived from petroleum refining. The catalytic conversion of lignin, a major lignocellulosic component, offers a renewable route to these chemicals. This review systematically examines the influence of pyrolysis methods, catalysts, and reaction conditions on the catalytic pyrolysis of lignin to aromatic hydrocarbons. Key parameters include catalyst acidity and pore structure, which govern selectivity and yield. Reaction temperature, catalyst-to-lignin ratio, and residence time critically affect product distribution. The review outlines catalytic mechanisms, such as deoxygenation, cracking, and aromatization, and highlights the role of zeolite catalysts, particularly HZSM-5, in enhancing monocyclic aromatic hydrocarbon yields. Metal modification (e.g., Fe, Ni, Ga) and pretreatment strategies (e.g., torrefaction) are discussed for improving efficiency. Challenges remain in catalyst deactivation due to coking and the complexity of lignin structure. Future research directions include developing robust catalysts, optimizing reactor designs, and integrating processes for industrial viability. This review provides theoretical and technological guidance for advancing lignin-to-aromatics conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3963-5
Metal additive manufacturing (MAM) enables integrated one-piece fabrication of parts, high material utilization efficiency, and unparalleled design freedom. However, problems such as low production efficiency, difficulties in ensuring quality stability and defect control limit the large-scale industrial application of AM. In-situ active modulation for AM enables dynamic regulation of parts during the fabrication process, thereby enhancing the quality of the final fabricated parts without introducing extra processing steps. In-situ active regulation enables direct intervention during defect nucleation, providing better effectiveness than post-printing repairs while avoiding performance degradation risks associated with post-processing. Based on the difference of core factors directly affected during regulation, in-situ active regulation is categorized into the following. (1) Process and path parameter optimization, where regulation directly impacts manufacturing-related procedural rules. It is the simplest method of control and the preferred approach, with widespread attention focused on its effects on microstructure and mechanical properties. (2) Laser beam shaping, where regulation directly influences the energy carrier morphology. To address issues such as edge over-melting and localized energy deficiency caused by non-uniform energy distribution, laser beam shaping should be employed. (3) Additional physical field modulation achieved by superimposing supplementary physical fields. When optimal process and path parameters still fail to obtain the desired microstructure and mechanical properties, additional physical field control may be considered. Meanwhile, this work summarized the effects of different additional physical fields on the mechanical properties of various metallic base materials. The future trends of in-situ modulation in additive manufacturing are also discussed.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4140-9
Metal covalent organic frameworks (MCOFs) are promising photocatalysts for carbon dioxide reduction reaction (CO2RR). However, the synthesis of ketimine-linked COFs remains challenging due to the low reactivity of ketones. Here, we report a straightforward strategy to construct diketimine-linked MCOFs via the condensation of acenaphthenequinone (Ace) with 1,3,6,8-tetra(4-aminophenyl)pyrene (TAPPy). The metal-free COF (TACOF-AA) exhibits AA stacking, while the addition of NiCl2·6H2O under identical conditions yields an AB-stacked Ni-based MCOF (Ni-TACOF-AB). The coordinated Ni species serve as active sites for CO2RR and enhance electron-hole separation. Photocatalytic tests demonstrate that Ni-TACOF-AB achieves a CO evolution rate of 11.71 mmol g−1 h−1 with 99.9% selectivity, which is 7.6 times higher than that of TACOF-AA. Density functional theory (DFT) calculations reveal that Ni-TACOF-AB lowers the activation energy barrier of the rate-determining step by regulating local charge distribution, facilitating electron transfer to adsorbed CO2. This work provides a novel approach for synthesizing ketimine-based COFs and highlights the importance of interlayer stacking in modulating photocatalytic performance.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0034
Catalytic cracking of gasoline and diesel to light olefins is a pivotal route for high-value utilization of surplus fuels, typically employing zeolite catalysts. This study systematically investigates the effects of zeolite type and acidic properties on the catalytic cracking of dodecane, a diesel model compound, using SAPO-34, ZSM-5 with SiO2/Al2O3 ratios of 38, 85, and 200, and USY. Catalysts were characterized by XRD, SEM, N2 physisorption, NH3-TPD, and pyridine-FTIR, and evaluated in a fixed-bed reactor. Results demonstrate that zeolite type is the primary determinant of conversion and product distribution. SAPO-34, with 0.38 nm pores, achieved only 24.33% conversion and negligible BTX yield, with severe external coking. ZSM-5-38 and USY, with larger pores, achieved near-complete conversion; however, ZSM-5-38, possessing moderate acidity, yielded the highest light olefins (18.40%) and minimal coke (0.18%), while USY, with higher acidity, promoted hydrogen transfer and coking (12.90% coke). Within ZSM-5 series, lower acid site density (ZSM-5-200) proved optimal, achieving 97.79% conversion and a total light olefin yield of 41.93% (ethylene 11.11%, propylene 20.33%, butenes 10.49%) with low coke (0.43%). The study proposes reaction pathways and regulatory mechanisms, highlighting that zeolite type and acidity govern the relative rates of cracking, hydrogen transfer, oligomerization, aromatization, and coking, thereby dictating performance. These findings provide a rational basis for optimizing zeolite catalysts in commercial gasoline/diesel cracking processes.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025032504
The environmental persistence and ecotoxicity of diclofenac sodium (DCF), a widely used non-steroidal anti-inflammatory drug, necessitate efficient removal strategies. Covalent organic frameworks (COFs) have emerged as promising adsorbents. Here, a novel nanoribbon COF (COF-TFPPy-DGCl) was synthesized via condensation of 1,3,6,8-tetrakis(4-formylphenyl)pyrene and 1,3-diaminoguanidine hydrochloride. The material was characterized by SEM, TGA, FT-IR, and PXRD. Batch adsorption experiments evaluated the effects of pH, contact time, and initial concentration. COF-TFPPy-DGCl exhibited a maximum adsorption capacity of 370 mg·g−1 for DCF, with capacity decreasing as pH increased. Adsorption kinetics followed a pseudo-second-order model, and equilibrium data fitted the Langmuir isotherm. Selectivity tests demonstrated a DCF removal rate of 96.75%, significantly higher than for ciprofloxacin and bisphenol A (<20%). The adsorbent retained 80% of its capacity after five regeneration cycles, indicating high stability. Mechanistic studies revealed that adsorption is driven by a synergistic combination of electrostatic interactions (dominant), π-π stacking, and hydrogen bonding, facilitated by uniformly distributed active sites. Rapid equilibrium was achieved within 30 minutes. These findings establish COF-TFPPy-DGCl as a highly selective, stable, and regenerable adsorbent for DCF removal from water, offering a theoretical basis for designing advanced COF-based water treatment materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3982-6
Skin wounds are refractory due to antibiotic-resistant bacterial infection. Although photodynamic therapy (PDT) offers noninvasiveness, high efficiency, and no drug resistance, its therapeutic effect is constrained by the complex structure of wound tissue and diffuse drug distribution. The proinflammatory cytokine tumor necrosis factor-like weak inducer of apoptosis (TWEAK) regulates tissue repair by engaging its receptor Fn14, which is highly expressed in wounds. In this study, we developed a novel photosensitizer, the selenoviologen-TWEAK conjugate (SeV-Tp), to enhance selective enrichment and synergistically promote wound healing. In vitro analyses demonstrated that SeV-Tp, under visible light, generated high levels of reactive oxygen species, resulting in potent antibacterial activity against both Gram-positive and Gram-negative bacteria. Notably, SeV-Tp selectively bound to Fn14 and amplified fibroblast activation via photodynamic cooperation. In a mouse model of antibiotic-resistant Pseudomonas aeruginosa-infected wound, SeV-Tp accelerated healing by reducing bacterial burden, modulating the immune microenvironment, promoting collagen deposition, and stimulating hair follicle regeneration. Moreover, SeV-Tp preferentially accumulated within wound tissues with minimal adverse effects. SeV-Tp represents a strategy that selectively enriches and harnesses synergistic benefits from both components, positioning SeV-Tp as a promising photosensitizer for the treatment of refractory wounds.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3855-8
The escalating environmental burden of plastic waste necessitates innovative chemical recycling strategies that circumvent the energy-intensive and catalytic limitations of conventional depolymerization. This study highlights a seminal advance by Qi Zhang, Da-Hui Qu, Ben L. Feringa, and co-workers, published in Nature Nanotechnology, which integrates supramolecular self-assembly with dynamic covalent chemistry to achieve catalyst-free, solvent-free polymer-to-monomer transformation. The system employs thioctic amide (TAA), a derivative of α-lipoic acid featuring reversible disulfide bonds and hydrogen-bonding amide groups. Notably, TAA monomers resist ring-opening polymerization upon melting due to cross-stacked packing driven by amide hydrogen bonds, which kinetically separates the 1,2-dithiolane rings. Introduction of formic acid (FA) as a supramolecular modulator disrupts the hydrogen-bond network, enabling dynamic disulfide ROP. Subsequent solvent removal yields nanocrystalline poly(disulfide) (Nc-poly(TAA)), which upon annealing at 120 °C reorganizes into a semicrystalline polymer (Sc-poly(TAA)) with a Young's modulus of 3.9 GPa, comparable to Nylon 6. The semicrystalline polymer exhibits hierarchical order with densely packed spherulites and periodic lamellae stabilized by reticular hydrogen bonds, conferring exceptional mechanical robustness and resistance to humidity (80% RH for six days). Rheological analyses reveal a relaxation time exceeding 90 years at room temperature, indicating a kinetically trapped, metastable state. Remarkably, the polymer reverts quantitatively to monomeric crystals under mild heating (120 °C, 24 h) without catalyst or solvent, achieving >90% purity and quantitative yield. The recovered monomer can be repolymerized to virgin-quality polymer, establishing a closed-loop cycle. Life-cycle assessment shows a carbon footprint of only 0.36 kg CO2 per kg product, underscoring the environmental benefits. This work demonstrates a fundamentally new route to circular polymers, merging supramolecular chemistry with dynamic covalent bonds for sustainable materials.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510017
Municipal solid waste (MSW) is a significant source of urban carbon emissions. This study integrates life cycle assessment (LCA) and system dynamics (SD) to construct a multi-subsystem LCA-SD model covering economy, population, waste generation, transportation, treatment, and resource utilization, using Fuzhou City as a case study. The model was validated against historical data and uncertainty analysis. Carbon emissions from MSW transportation, treatment, and resource utilization during 2013–2023 were calculated, and emission trends under seven reduction scenarios for 2024–2035 were predicted. Results show that Fuzhou's MSW treatment evolved through three stages: 'landfill+incineration', 'treatment structure adjustment', and 'incineration+kitchen waste resource utilization', corresponding to emission growth, fluctuation, and reduction periods. In 2023, total net carbon emissions were 1.07×10^6 t CO2-eq, with incineration being the largest contributor (9.93×10^5 t), followed by transportation (2.93×10^4 t), leachate treatment (2.14×10^4 t), and kitchen waste treatment (7.90×10^3 t, negative emission). Scenario analysis indicates that without further measures, carbon neutrality cannot be achieved. Synergistic enhancement of kitchen waste separation and incineration power generation efficiency can significantly boost reduction, potentially achieving carbon neutrality by 2032. The study provides a dynamic accounting and scenario assessment framework for low-carbon transition of urban solid waste systems.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60680-9
Low-temperature chemical looping air separation (CLAS) is a promising technology for producing oxygen-enriched gas streams, utilizing the redox properties of solid oxygen carriers to selectively capture and release oxygen from air. Oxygen vacancy formation energy (Eovf) is a key descriptor for evaluating the ease of oxygen release. In this study, the applicable range of Eovf for CLAS oxygen carriers was determined to be <2.3 eV via thermodynamic calculations. A graph neural network (GNN) model, specifically the ALIGNN architecture, was trained to predict Eovf with a mean absolute error (MAE) of 0.26 eV on the test set. Using this model, a high-throughput screening of 3,649 compositions of SrxA1−xFeyB1−yO3 perovskites was conducted to identify promising CLAS oxygen carriers. The predictions revealed that doping with Ba and Ca at the A-site and Co at the B-site effectively reduces Eovf. The screening criterion of Eovf < 2.3 eV successfully rediscovered several previously reported low-temperature CLAS oxygen carriers, validating the approach. This work demonstrates that GNN-based Eovf prediction can significantly accelerate the discovery of CLAS materials, with broader implications for other chemical looping applications such as full oxidation and syngas production.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608026
Biochar and microbial inoculants are widely used for agricultural soil amendment. To investigate the effects of different straw biochars and Bacillus subtilis inoculant, applied individually or combined, on nitrogen transformation in dryland soil, a 60-day laboratory incubation experiment was conducted with six treatments: control (CK), 4% rice straw biochar (S), 4% rapeseed straw biochar (Y), 4% rice straw biochar plus 5 mg/kg inoculant (SJ), 4% rapeseed straw biochar plus 5 mg/kg inoculant (YJ), and inoculant alone (J). Results showed that rice straw biochar significantly increased soil nitrate nitrogen content by 148.74%–152.68% compared to CK, enhancing nitrification. Combined application with inoculant further increased average net nitrogen mineralization rate by 77.28%–99.38%. Conversely, rapeseed straw biochar decreased nitrate nitrogen by 51.66%–57.61%, and combined application reduced net nitrogen mineralization rate by 82.07%–84.73%. Treatments S, Y, SJ, and YJ promoted microbial biomass nitrogen (MBN) synthesis, with S and Y increasing MBN by 2.02- and 2.20-fold over CK, respectively. Combined treatments further increased MBN by 103.26%–149.44% relative to single biochar treatments. These findings indicate that biochar type governs nitrification and net nitrogen mineralization, while combined application exerts synergistic effects on MBN. For comprehensive dryland soil improvement, YJ treatment is optimal, reducing inorganic nitrogen loss risk and enhancing microbial nitrogen activity.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60721-9
Methane (CH4), the primary component of natural gas, is an ideal feedstock for producing high-value chemicals and clean fuels due to its high hydrogen-to-carbon ratio. However, its chemical inertness poses significant challenges, and traditional thermal catalytic reforming processes suffer from long reaction pathways and high energy consumption. Photocatalytic technology enables highly selective CH4 conversion under mild conditions, even at room temperature, offering environmental and economic benefits. This review systematically summarizes recent advances in room-temperature photocatalytic systems for direct CH4 conversion. It begins by elucidating the mechanisms, product distributions, and inherent challenges of four key reaction pathways: partial oxidation, non-oxidative coupling, oxidative coupling, and oxidative carbonylation. The discussion then addresses the critical role of catalyst architecture, focusing on semiconductor supports, metal site modulation, and advanced porous frameworks. Furthermore, reactor design and process intensification strategies are examined, including batch and continuous-flow reactors, novel structured reactors, and photo-electro and photo-thermo synergistic approaches. Finally, reaction mechanisms are summarized. Despite progress, challenges remain in fundamental understanding, performance evaluation, and technological integration. Future efforts should focus on mechanistic studies, standardization of evaluation protocols, development of non-noble metal catalysts, system optimization, and comprehensive sustainability assessments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4098-8
Fluorescence image-guided photodynamic therapy (PDT) enables real-time monitoring of photosensitizer biodistribution and metabolism for optimized treatment timing. However, its application remains limited by reliance on high-end imaging systems. To address this, we designed three novel small-molecule photosensitizers (TTNb, TTAn, TTPh) based on a 2-vinylbenzoic acid scaffold, functionalized at the 5-position with nitro, amino, or hydrogen groups. Replacing the nitro group with amino or hydrogen switched aggregation behavior from aggregation-induced emission (AIE) to aggregation-caused quenching (ACQ), accompanied by a red-to-green fluorescence shift and subcellular relocation from liposomes to lysosomes. These findings establish design principles for ratiometric nitroreductase probes and enable systematic comparison between AIE and ACQ photosensitizers. Among these, TTAn exhibited superior cellular uptake (2800 times higher than Ce6 in Eca-109 cells), specific lysosomal targeting, balanced reactive oxygen species (singlet oxygen/superoxide anion) generation, and intense fluorescence. Under white light irradiation, TTAn achieved an IC50 of 21 nM, surpassing Ce6 by 50-fold. Notably, TTAn produced strong fluorescence in mice tumors under both one- and two-photon excitation, detectable using conventional imaging tools (smartphones, DSLR cameras) or even visible to the naked eye, confirming outstanding tumor specificity. Leveraging these advantages, TTAn enabled successful image-guided two-photon PDT in Eca-109 tumor-bearing mice with a single treatment, demonstrating potent therapeutic efficacy and biosafety. This work provides a strategic blueprint for developing small-molecule theranostic agents that operate without complex fluorescence imaging systems.