SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4271-5
Photocatalytic functional coatings are at a pivotal juncture where the primary research focus must transition from intrinsic material activity to a unified framework centered on surface serviceability. Surface serviceability encompasses the ability of a coating to maintain catalytic activity, interfacial integrity, multifunctional performance, safety, and manufacturability under specific service environments over its operational lifetime. Over the past three decades, photocatalytic surfaces have demonstrated potential for degrading organic pollutants, maintaining surface cleanliness, and enabling air purification, with applications in buildings, glass, highways, and infrastructure. However, high intrinsic activity alone does not guarantee stable long-term performance when the photocatalyst is immobilized as a substrate-integrated film. Performance is governed by coupled factors including interfacial adhesion, film structure, environmental aging, and functional durability. Current challenges extend beyond catalytic activity to include long-term deactivation, coating-substrate interfacial stability, trade-offs among multiple functions, adequacy of evaluation methods, and scalability of fabrication. These issues form a progressive service chain: design determines catalyst exposure and adhesion; environmental stresses induce functional or structural failure; multifunctional integration may compromise one function for another. Therefore, application-oriented evaluation is essential. This perspective advocates for a paradigm shift toward service-oriented design, requiring establishment of service-relevant evaluation protocols and development of scalable, repairable fabrication routes. Such efforts will enable photocatalytic coatings to evolve from high-activity laboratory materials into engineering surfaces that are verifiable, comparable, manufacturable, and durable in real-world applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4113-3
Constructing abundant grain boundary defects is a promising strategy for developing high-efficiency catalysts. However, achieving dense grain boundary defects in CuO and Cu at the nanoscale remains challenging. Inspired by Turing patterns in nature, a Turing-type CuO catalyst (TGB-CuO) with abundant grain boundaries at ~10 nm nanoscale was prepared by annealing a dodecyl sulfate-intercalated basic copper carbonate. The balanced diffusion-reaction dynamics during pyrolysis drove the spontaneous formation of Turing-type grain boundary architectures in TGB-CuO. The resulting TGB-CuO electrode exhibited outstanding performance in electrochemical CO2 reduction (ECO2RR), delivering a Faradaic efficiency of 80.15% toward multi-carbon (C2+) products and maintaining over 50% ethylene selectivity at 300 mA cm−2 for 30 h of continuous operation. Activity investigations indicated that the metallic Cu retaining Turing-type grain boundary features (TGB-Cu) formed during electroreduction was responsible for the enhanced ECO2RR performance. The Cu(100)/(100), Cu(100)/(111), and Cu(111)/(111) grain boundaries promoted CO2 activation and *CO adsorption, while lowering the free energy barriers for the rate-determining *CO2− → *COOH step and C–C coupling step. This bioinspired reaction-diffusion strategy offers a new paradigm for creating high-density grain boundary defects, offering a general route toward efficient catalyst design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4192-y
Electrochemical water splitting is pivotal for scalable green hydrogen production, yet its practical deployment hinges on cost-effective electrocatalysts with high activity and durability. This study introduces a low-cost, three-dimensional (3D) nanoporous ZrVFeCoNi material fabricated via chemical dealloying, at merely 0.16% of the cost of Pt. The structure-activity relationship between its microstructure and hydrogen evolution reaction (HER) performance was systematically explored. Lattice defect effects from multiphase intermetallic compounds, combined with multi-metal synergy, optimize H+ adsorption energy and electron transfer kinetics. The 3D nanoporous architecture provides a high electrochemical surface area with abundant active sites, enhancing electrolyte penetration and reducing interfacial mass transfer resistance. Consequently, the ZrVFeCoNi electrode exhibits outstanding HER performance, requiring only a 38 mV overpotential to reach 10 mA cm−2 and maintaining stable operation for 1000 h at 500 mA cm−2. Integrated into a full water electrolyzer (ZrVFeCoNi || IrO2/Ni), the system achieves a cell voltage of 1.60 V at a current density of 400 mA cm−2. Advanced characterization and density functional theory (DFT) calculations reveal that interfacial interactions and charge transfer at heterointerfaces drive catalytic activity, showcasing the potential of 3D nano-structured multiphase intermetallic compounds as high-performance electrocatalysts for green hydrogen systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4197-4
Deep-blue organic light-emitting diodes (OLEDs) remain the most challenging primary-color emitters due to stringent exciton energy requirements. We strategically designed two innovative deep-blue emitters, SCZ-4AnCN and STPA-4AnCN, via systematic functionalization of an anthracene core with arylamino-decorated spirofluorene donors and cyano-substituted phenyl acceptors. Comprehensive theoretical and experimental analyses demonstrate that these spirofluorene-anthracene hybrids adopt precisely engineered distorted configurations, effectively suppressing detrimental intermolecular π–π stacking in condensed phases. The sp3-hybridized bridgehead carbons in spirofluorene units play a pivotal role by simultaneously restricting π-conjugation extension and fine-tuning donor–acceptor interactions, thereby stabilizing the lowest excited singlet (S1) state with dominant local excitation (LE) character. This molecular engineering yields exceptional deep-blue emission with remarkable efficiency. Notably, the materials exhibit unique high-lying reverse intersystem crossing (hRISC) behavior, enabling efficient triplet harvesting. Optimized doped devices incorporating SCZ-4AnCN achieve outstanding performance, including a maximum external quantum efficiency (EQE_max) exceeding 10% and CIE coordinates (0.154, 0.052) approaching the BT.2020 blue standard. Nondoped devices maintain impressive performance with an EQE_max of 7.51% and superior operational stability, demonstrating less than 10% efficiency roll-off at 1000 cd m−2. This work validates anthracene-based molecular architectures for deep-blue electroluminescence and establishes a transformative design paradigm for next-generation OLED emitters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3888-9
Flexible thermoelectrics (f-TEs) are being developed rapidly due to their unique advantages, such as direct conversion between electricity and thermal energy, compatibility with curved heat sources, and ease of integration. Over the past decade, significant progress has been made in enhancing the overall performance of f-TE materials and devices, particularly in terms of output power, mechanical flexibility, and durability. Recent research efforts are increasingly focused on translating these advancements into practical applications across diverse fields. For example, f-TE-based multimodal sensors are capable of simultaneously detecting temperature, pressure and strain. In biomedicine, f-TE generators are being explored for wound healing, antibacterial therapy, and neural modulation. Furthermore, f-TE devices show promise in personalized thermal management and hybrid energy harvesting systems. This review moves beyond material preparation and device optimization to focus on the expanding multifunctional applications of f-TEs. We provide a broad perspective by comprehensively exploring the latest progress of f-TEs in intelligent sensing, biomedicine, personalized thermal management, and multifunctional hybrid systems. Key challenges are also discussed, including the development of high-performance flexible devices, robust bio-interfaces, ensuring long-term stability, and achieving intelligent integration with data-driven algorithms and multimodal platforms. Finally, we offer insights into future directions for f-TEs, pointing toward next-generation intelligent and bio-integrated flexible electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3780-3
Real-time health monitoring and ongoing evaluation of physiological conditions are becoming increasingly vital for the advancement of future medical diagnostics and personalized healthcare solutions. Given that certain illnesses necessitate prompt and accessible detection methods, wearable chemical sensors have garnered considerable interest for their capability to monitor health through physiological signals and chemical indicators. This review delivers a thorough examination of recent developments in four primary categories of wearable chemical sensors: biosensors, humidity sensors, gas sensors, and ion sensors. We explore the representative materials, device structures, operating mechanisms, and various application scenarios for each type of sensor. By investigating the latest innovations in these technologies, we aim to provide a detailed overview of the current research landscape, highlight existing challenges, and present potential future directions of wearable chemical sensors in healthcare monitoring.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507027
Ammonia nitrogen (NH3-N) is a common water pollutant that can induce eutrophication and threaten aquatic ecosystems and human health. Accurate monitoring is essential for water safety. This study applied a self-developed gas-permeable membrane-based conductivity sensor (GPMCS) for real-time in-situ monitoring of NH3-N in two water bodies. In the Qunying River (surface river water), GPMCS captured concentration fluctuations linked to pump operations and sewage intrusion, with mean inlet and outlet concentrations of 4.67 and 3.42 mg/L, respectively. In Swan Lake (landscape aquaculture water), concentrations reached up to 11.16 mg/L, with site means of 6.42 and 7.04 mg/L, influenced by aquaculture activities, weather, and location. GPMCS results correlated strongly with national standard methods (r1=0.8132, r2=0.7483), confirming accuracy and reliability. Compared to existing techniques, GPMCS offers high selectivity, strong anti-interference, portability, no sample pretreatment, low cost, and environmental friendliness, making it suitable for long-term in-situ monitoring. This technology provides robust support for sustainable water environment management.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025101101
Acetamiprid, a representative neonicotinoid insecticide, persists in soil and water, posing ecological risks. This study evaluated its transgenerational toxicity in Caenorhabditis elegans exposed to 1, 10, and 100 μg·L−1. Direct exposure (F0) caused neurobehavioral abnormalities, with head swing frequency significantly increased by 23.86% even at 1.0 μg·L−1, correlating with disrupted acetylcholinesterase and γ-aminobutyric acid. Reproduction, development, metabolism, and intestinal barrier were impaired, with reactive oxygen species elevated by 30.42%–48.28%, indicating oxidative stress as a mechanism. Effects transmitted to unexposed T1–T3 generations: at 1.0 μg·L−1, body width inhibition persisted to T2; fat accumulation and intestinal permeability effects intensified with concentration. Among oxidative stress biomarkers, superoxide dismutase showed highest sensitivity and transgenerational persistence. This study reveals multidimensional transgenerational toxicity, informing soil ecological risk assessment of neonicotinoids.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024120701
Surface waters contain numerous photoactive substances and low molecular weight carboxylic acids (LCAs). Hydroxyl radicals (HO•) can react with LCAs to generate the highly reducing carbon dioxide anion radical (CO2•−). Excited triplet state dissolved organic matter (3DOM*), a common oxidant in surface waters, may also oxidize LCAs to CO2•−, but this pathway remains unexplored. This study simulated sunlight-driven generation of CO2•− via 3DOM* using 4-benzoylbenzoic acid (CBBP) as a 3DOM* precursor and formate (HCOO−) as a model LCA. Metronidazole (MNZ) served as the target pollutant. Comparative degradation experiments in hν, hν/HCOO−, hν/CBBP, and hν/CBBP/HCOO− systems, combined with electron spin resonance spectroscopy and quenching tests, confirmed that CO2•− generated in the hν/CBBP/HCOO− system was the primary reactive species responsible for enhanced MNZ degradation, originating mainly from 3CBBP* oxidizing HCOO−. Under optimized conditions (8 mmol·L−1 HCOO−, 200 μmol·L−1 CBBP, 10 μmol·L−1 MNZ), 98.2% degradation was achieved within 30 min. Degradation efficiency increased with HCOO− concentration and was pH-independent. Cl−, NO3−, CO3^2−, and low concentrations of HCO3− inhibited degradation, while high HCO3− slightly promoted it. Humic acid (HA) inhibited degradation in a concentration-dependent manner. The system also performed well in real water matrices, suggesting potential for treating micropollutants via reductive pathways.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024102403
The rapid combustion of soot at low temperatures is critical for diesel engine cold-start emission control. This study investigates the effects of water vapor (H2O) and nitrogen oxides (NOx) on electricity-pulse-sparked catalysis (EPSC) for soot combustion over a ceramic filter paper-based potassium-supported antimony-doped tin oxide (K/ATO/CP) monolithic catalyst. Under EPSC with 2000 J pulses, the presence of H2O and NOx adversely affected soot combustion performance, yet average reaction rates remained high at 12.0 μmol·gcat−1·s−1 and 9.53 μmol·gcat−1·s−1, respectively, exceeding conventional thermal catalysis (<8 μmol·gcat−1·s−1). In situ Raman and concentration profiles revealed that electricity pulses promote rapid H2O desorption, effectively alleviating H2O poisoning and restoring catalyst activity. In contrast, NOx adsorption forms stable nitrates (e.g., KNO3) that desorb slower than the soot combustion process, leading to incomplete recovery of activity. These findings highlight the importance of adsorbate desorption kinetics in EPSC and suggest that using weakly basic alkaline-earth metals (e.g., Mg, Ca, Sr) with lower nitrate decomposition temperatures could mitigate NOx poisoning. The results provide guidance for advancing EPSC technology in hybrid vehicle exhaust aftertreatment systems.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61097-9
Silicon/carbon (Si/C) composites are promising anode materials for high-energy-density lithium-ion batteries (LIBs) because they mitigate the severe volume expansion and poor electrical conductivity of pure silicon anodes. This review systematically summarizes the state-of-the-art preparation methods for Si/C composites, including ball milling, spray drying, electrostatic spinning, and chemical vapor deposition (CVD). Structural engineering strategies, such as carbon precursor coating, silicon-precursor-based wet chemistry, and silicon surface modification, are critically assessed for their effectiveness in enhancing electrical conductivity, buffering volume changes, and improving overall electrochemical performance. The review highlights that while Si offers a theoretical capacity of 4200 mAh g−1, far exceeding graphite's 372 mAh g−1, its practical application is hindered by capacity fading and low initial coulombic efficiency. The integration of carbon matrices not only provides mechanical flexibility but also facilitates electron transport. Key performance metrics from recent studies, including specific capacities exceeding 1000 mAh g−1 and improved cycling stability over hundreds of cycles, are discussed. The review also addresses the challenges of scalable production and cost-effectiveness, emphasizing the need for optimized precursor selection and processing parameters. Future research directions are proposed, focusing on the rational design of hierarchical structures and the development of novel binders to further enhance the long-term durability of Si/C anodes. This comprehensive overview serves as a valuable resource for researchers and engineers aiming to advance the commercialization of high-energy-density LIBs.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025030403
Microplastics (MPs) act as vectors for co-migrating antibiotics and heavy metals, forming complex pollution systems with potential joint toxicity. However, the differential adsorption behaviors and underlying mechanisms of MPs toward organic versus inorganic pollutants remain insufficiently understood. This study selected polypropylene (PP) microplastics, a major component of agricultural plastic films, and investigated the adsorption of sulfamethoxazole (SMX) and Cr(VI) onto aged PP under varying environmental conditions. Results demonstrated that aging increased the maximum adsorption capacity by 2–3 times for both pollutants. Notably, aged PP exhibited approximately 30 times higher adsorption capacity for SMX than for Cr(VI). Characterization revealed that aging introduced oxygen-containing functional groups (e.g., carbonyl) on the MP surface, enhancing adsorption. Mechanistic analysis indicated that hydrogen bonding and electrostatic interactions dominated SMX adsorption, while Cr(VI) adsorption was primarily governed by electrostatic interactions and pore-filling. The stronger intermolecular forces for SMX compared to reversible pore-filling for Cr(VI) explained the observed differences. Increasing pH induced electrostatic repulsion, reducing adsorption of both pollutants. High concentrations of Na+ and Mg2+ caused charge shielding, potentially enhancing Cr(VI) adsorption but inhibiting SMX adsorption due to competition for active sites. The presence of organic matter (humic acid) had negligible effects on Cr(VI) adsorption but reduced SMX adsorption, likely due to complexation. These findings elucidate distinct molecular-level pathways for organic versus inorganic pollutant adsorption on aged MPs, highlighting the roles of hydrogen bonding and pore-filling in driving differential behaviors.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606002
Industrial volatile organic compounds (VOCs) emissions are a major contributor to regional air pollution, and the rubber paste preparation process is a significant source. This study developed an intelligent monitoring system for whole-process VOCs management in a rubber paste preparation workshop, integrating software engineering and Internet of Things (IoT) technologies. The system architecture combines a hybrid database (MySQL relational and InfluxDB time-series), MQTT-based low-power wide-area communication, role-based access control, and containerized microservices. Field deployment at a large rubber enterprise enabled real-time monitoring of adsorption/desorption centrifugal fans and data fusion analysis. Under typical operating conditions, the extraction and ventilation systems achieved volume flow rates of 40,000 m³/h and 30,000 m³/h, respectively, maintaining a continuous micro-negative pressure environment that effectively suppressed fugitive emissions. The purification process, comprising zeolite rotor adsorption and regenerative thermal catalytic oxidation, reduced non-methane hydrocarbon (NMHC) concentrations to below 10 mg/m³, meeting the GB 27632—2011 emission standard. The system's multi-level permission management module precisely allocated operational responsibilities across production, environmental, and management roles, reducing response time to abnormal conditions. An online evaluation model for purification efficiency was constructed based on the actual process. The system demonstrates potential for extension to other high-VOCs industries such as coatings and printing. This research provides theoretical and practical references for applying computer technology to VOCs reduction and whole-process management in typical industries.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026021301
Lithium cobalt oxide (LCO) nanoparticles (NPs), generated during the lifecycle of LCO batteries via mechanical wear, pose respiratory health risks. This study systematically assessed LCO NPs' physicochemical properties, ion release, and immunotoxicity using multi-scale models. LCO NPs exhibited irregular morphology, layered crystal structure, good dispersion, and negative surface charge. Cobalt ion release was minimal: 1.03% in deionized water and 0.11% in cell culture medium. In vitro, LCO NPs significantly induced reactive oxygen species (ROS) production and secretion of pro-inflammatory cytokines (IL-6, IL-1β, TNF-α) in macrophages, promoting M1 polarization. In vivo, intranasal exposure caused dose-dependent pulmonary accumulation, alveolar destruction, inflammatory cell infiltration, and elevated cytokines in bronchoalveolar lavage fluid (BALF). Transcriptomic analysis revealed significant enrichment of NF-κB, JAK-STAT, and Toll-like receptor signaling pathways, implicating these in macrophage activation and inflammation amplification. This multi-level study elucidates LCO NPs' immunotoxicity mechanisms, providing a scientific basis for environmental health risk assessment and management of lithium-ion battery materials.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607010
The impact of low concentrations of perfluorooctane sulfonate (PFOS) on anaerobic fermentation of waste activated sludge (WAS) remains poorly understood. This study applied three PFOS levels (0.5, 1.0, and 4.5 μg/g TSS) to systematically evaluate effects on organic matter solubilization and nitrogen/phosphorus transformations. Monitoring of soluble chemical oxygen demand (SCOD), soluble protein, polysaccharides, NH4+-N, PO43--P, and three-dimensional excitation-emission matrix (3D-EEM) fluorescence revealed that PFOS significantly enhanced release of SCOD, protein, and polysaccharides. At 45 °C after 14 days with 4.5 μg/g TSS, SCOD peaked approximately 28% higher than control, indicating increased biodegradable organic matter accumulation. NH4+-N concentrations rose overall with fluctuations, while PO43--P release was inhibited, suggesting interference with nutrient transformation pathways. 3D-EEM analysis showed strengthened signals of aromatic proteins and microbial by-products, confirming matrix solubilization. These findings demonstrate a dual effect of low-level PFOS: initial promotion of organic matter release followed by potential inhibition of nutrient transformation. This study provides data support for understanding PFOS environmental behavior in anaerobic digestion and informs sludge resource utilization and risk assessment of emerging contaminants.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607025
The Holocene alluvial-diluvial stratum of the Quaternary is characterized by high soil hydraulic conductivity and intense surface water-groundwater interaction, which leads to rapid and extensive migration of contaminants from landfills. To investigate the contaminant characteristics of a municipal solid waste (MSW) landfill in such strata, a case study was conducted at a landfill in southwestern China. Methods including the Nemerow pollution index and the potential ecological risk index were employed to systematically analyze the contamination of groundwater and soil, as well as the spatial distribution of organic matter and heavy metals. The results showed that the groundwater was severely contaminated (PI > 3). The maximum exceedance multiples for total bacterial count, ammonia nitrogen (NH4+-N), and total coliforms relative to the standard limits were 36, 9.5, and 8, respectively. The composition of the contaminants in groundwater was highly consistent with the characteristics of landfill leachate. For the soil, the concentrations of six heavy metals (Cu, Pb, Cd, Ni, Hg, and As) were all below the Class II screening values of the standard GB 36600—2018. Both the Nemerow pollution index (PI < 0.7) and the potential ecological risk index (RI < 150) indicated that the soil environment was safe. Regarding soil dissolved organic matter (DOM), humic-like substances (22.9% to 34.9%) and fulvic-like substances (22.4% to 27.5%) were the dominant components, and their fluorescence intensities exhibited an exponential decay trend with increasing soil depth. The speciation of Cu, Pb, As, Hg, and Ni was dominated by the residual fraction (52.33% to 90.32%). However, over 70% of Cd existed in active forms (exchangeable + Fe/Mn oxide-bound), suggesting a high migration risk. The horizontal distribution of heavy metals showed regional specificity, with high-value areas mainly concentrated in the screening waste and soil stacking areas. Vertically, Cu and Cd exhibited surface enrichment, while As, Hg, Pb, and Ni were enriched in the groundwater fluctuation zone. These findings indicate that groundwater in alluvial-diluvial strata is highly susceptible to leachate contamination, while soil heavy metal contamination is not significant, with low levels in the aquifer but a tendency to accumulate at the water-soil interface. It is recommended that during landfill remediation, attention be paid to anti-seepage measures in waste excavation and stacking areas, as well as the interception and remediation of the groundwater fluctuation zone, to prevent secondary contamination of soil and groundwater.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3984-5
Rechargeable aluminum batteries (RABs) are promising for large-scale energy storage due to high theoretical capacity, inherent safety, and abundant aluminum reserves. However, conventional AlCl3-based ionic liquid electrolytes suffer from high cost, uncontrolled dendrite growth, and severe anode corrosion. Here, a molecular-level ligand engineering strategy is proposed, employing nitrogen-containing cyclic amides with tunable N–H functionalities to modulate the coordination environment of deep eutectic electrolytes (DEEs). Combined experimental and theoretical investigations reveal that the α-pyrrolidone-based DEE (PDEE) possesses a wider electrochemical window, higher ionic conductivity, and lower polarization. Precise N–H regulation optimizes cationic ligand and chloroaluminate anion interactions, accelerating ion transport to facilitate uniform Al deposition without dendrites. The amine functionalities enable in situ construction of a uniform inorganic-organic bilayer solid electrolyte interphase, mitigating anode corrosion and enhancing long-term interfacial stability. As a result, Al//Al symmetric batteries with PDEE achieve stable cycling for over 2000 hours, while Al-graphite full batteries demonstrate negligible capacity decay after 6000 cycles. This study establishes that ligand molecular engineering offers an effective strategy for optimizing DEEs, enabling durable and high-performance RABs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3825-x
Polymer-based dielectric materials with high energy density and thermal stability are critical for modern electric/electronic industries. Polyimide (PI) based materials are promising due to their high temperature resistance and chemical inertness, yet their inherently low dielectric constant and limited charge-discharge energy density restrict applications in film capacitors. While incorporating ferroelectric or conductive fillers can enhance dielectric performance, batch-to-batch inconsistency and physical deterioration remain problematic. This study focuses on molecular structure design and modulation, preparing hyperbranched polyimides with different dianhydride monomers and branching degrees. The effects of chain packing density with polar groups on dielectric and energy storage performances were systematically investigated via experimentation and molecular simulation. Results demonstrate a significant correlation between monomers' electrical distribution and packing density in polymer systems. Molecular simulation further elucidated the underlying mechanism. This work establishes a foundation for designing polymer-based dielectric materials with high dielectric and energy storage performances at the molecular level.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60672-X
Dry reforming of methane (DRM) converts CH4 and CO2 into syngas, offering a route to mitigate greenhouse gases. Ni-based catalysts suffer from sintering and carbon deposition at high temperatures. This work employs MgO-MgAl2O4 composite supports to regulate Ni loading and introduces Ce, La, and Zr as promoters to investigate their effects on DRM activity, structural stability, and surface oxygen species. Optimal Ni loading of 12.5% yields highest CH4 and CO2 conversions. Promoter introduction slightly suppresses low-temperature activity but substantially modifies support local structure and metal-support interface, improving NiO dispersion and increasing surface oxygen vacancies and active oxygen species (Oβ). These changes enhance CO2 adsorption-activation and suppress carbon deposition. After 20 h DRM, Ce-promoted catalyst shows smallest Ni particle growth (6.23→8.07 nm) and lowest carbon deposition, demonstrating superior stability and anti-coking capability. The study elucidates how Ce, La, and Zr enhance sintering and coking resistance via interfacial electronic modulation and improved oxygen storage/release, guiding rational design of stable Ni-based DRM catalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3998-8
Constitutional isomerism in covalent organic frameworks (COFs) has emerged as a powerful strategy to tailor material properties for photocatalytic applications. Here, we report the design and synthesis of two isomeric multicomponent COFs (MC-COFs) via Schiff-base condensation followed by Povarov reaction, converting imine linkages into quinoline structures. These isomeric MC-COFs exhibit opposing C=N bond orientations and distinct phenyl group alignments within the COF pores, leading to different torsion angles in the COF layers. Structural analyses reveal that enhanced planarity promotes π-π stacking and electron delocalization, resulting in favorable band structures and reduced exciton binding energies. Consequently, the optimized COF achieves a superior hydrogen peroxide (H2O2) production rate of 3128 μmol g−1 h−1 under visible light irradiation. This work underscores the critical influence of structural isomerism on the photocatalytic efficiency of MC-COFs and provides insights for rational design of high-performance COF-based photocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4017-y
Lattice distortion via entropy engineering can significantly optimize thermoelectric performance by intensifying phonon scattering. However, excessive lattice distortion in high-entropy materials inevitably hinders carrier transport, limiting the wide-temperature average ZT (ZTave). To enhance the wide-temperature thermoelectric performance of low-cost PbS-based compounds, this work introduces moderate lattice distortion by controlling entropy around 1.0R (R is the gas constant) to balance phonon and carrier transport, alleviating restrictions on carrier mobility. Substantial Se and Te alloying in PbS induces rock-salt lattice distortion, effectively impeding phonon propagation, thus suppressing lattice thermal conductivity (κlat) from 2.41 W m−1 K−1 in PbS to 0.66 W m−1 K−1 in PbS0.5Se0.35Te0.15 at 300 K. Additionally, Cu interstitials are introduced into the lattice-distorted PbS0.5Se0.35Te0.15 to further optimize carrier density and weighted carrier mobility (μW), leading to significant improvement in μW/κlat parameter at 300–773 K. Finally, a room-temperature ZT of 0.53 and a maximum ZT of 1.44 are obtained in PbS0.5Se0.35Te0.15-1%Cu sample, contributing to an impressive ZTave of 1.08 at 300–773 K and a maximum power generation efficiency (ηmax) of 7.5%. The results outperform previously reported cost-effective PbS-based compounds and highlight the importance of lattice distortion regulation in enhancing wide-temperature thermoelectric performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4175-3
The precise manipulation of microdroplets (diameter < 20 μm) on solid substrates is critical for applications in environmental monitoring, targeted drug delivery, clinical diagnostics, and public health. A major challenge is contact angle hysteresis (CAH), which pins droplets and impedes mobility. Here, we introduce a crack-mediated capillary bridging strategy for efficient capture and directional transport of microdroplets. The approach employs a stretchable elastomeric substrate with island-like microstructures. Under longitudinal tensile stress, controlled fracture generates densely packed, directionally oriented surface cracks. These fissures induce localized capillary forces that counteract adhesion-induced resistance, enabling programmable droplet motion. Experiments capturing airborne pathogenic agents demonstrated a 14.2-fold enhancement in enrichment efficiency compared to flat surfaces. This work integrates fracture mechanics with capillary-driven fluid dynamics, establishing a framework for next-generation microfluidic systems. The findings offer promising avenues for biosensing, pollutant analysis, and interdisciplinary applications.