SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4441-7
Early detection of kidney injury remains difficult because routine clinical indicators often lag behind tissue damage. Here we report uNP-CH1055, an ultrasmall renal-clearable NIR-II fluorescent nanoprobe for non-invasive imaging of kidney injury in vivo. uNP-CH1055 formed stable nanoparticles with a hydrodynamic diameter of 3.3 nm, showed good photostability, enabled low-background imaging under a 1200 nm long-pass filter, and underwent rapid renal clearance after intravenous administration. It also exhibited favorable biocompatibility in both cellular and animal studies. In three mechanistically distinct models of renal injury, cisplatin-induced acute kidney injury, ischemia–reperfusion injury and unilateral ureteral obstruction, renal fluorescence increased with injury severity and closely paralleled biochemical and histological indicators, including blood urea nitrogen, serum creatinine, KIM-1 and TUNEL-based readouts. These results identify uNP-CH1055 as a renal-clearable NIR-II probe for early and quantitative assessment of kidney injury across different pathological settings.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4476-1
Self-sustained oscillation in soft actuators enables autonomous, untethered robotic locomotion, yet existing light-driven systems suffer from low oscillation frequencies, rapid photothermal degradation, and reliance on external controllers. This work presents a bat-inspired soft robot that converts continuous near-infrared (NIR) irradiation into sustained rotational motion via a coiled MXene-based liquid crystal elastomer (LCE) actuator. The actuator integrates Ti3C2Tx MXene nanosheets as photothermal converters within an LCE matrix, achieving a photothermal conversion efficiency of 78.3% and a steady-state temperature of 142 °C under 1.5 W cm−2 NIR (808 nm). The coil geometry induces a self-shadowing effect that generates periodic light exposure, producing autonomous oscillation at 2.7 Hz with an amplitude of 45°. The robot demonstrates a rotational speed of 120 rpm and a specific power density of 3.2 W kg−1, outperforming previously reported light-driven oscillators by a factor of 2.5. Under continuous operation for 10,000 cycles, the actuator retains 92% of its initial oscillation amplitude, with a degradation rate of 0.008% per cycle. The bat-inspired wing morphology enables directional rotation and obstacle avoidance in confined spaces. This platform eliminates the need for external modulation, offering a scalable route to autonomous soft robotics for inspection, environmental monitoring, and micro-manipulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4497-y
Proton exchange membrane water electrolysis (PEMWE) enables green hydrogen production from renewable electricity but relies on scarce Ir/Ru catalysts for the kinetically sluggish and acid-stable oxygen evolution reaction (OER). Non-noble-metal oxides typically suffer rapid dissolution and structural collapse under acidic, high-current conditions. Conventional cubic spinel Co3O4 (C-Co3O4) contains both inactive tetrahedral Co and active octahedral Co sites; tetrahedral dissolution destabilizes the framework. A recently reported trigonal Co3O4 phase (Tri-Co3O4), synthesized via vacuum-mediated molten-alkali mechanochemical methods, consists entirely of edge-shared [CoO6] octahedra in a compact two-dimensional layered structure. This configuration eliminates tetrahedral sites and exposes abundant octahedral active centers. Structural characterization by X-ray diffraction confirms strong (0001) and (0002) reflections, while Co K-edge EXAFS shows only Co-Cooct coordination without Co-Cotet signals. Tri-Co3O4 achieves 10 mA cm-2 at an overpotential of 269 mV, 181 mV lower than C-Co3O4 (450 mV), with low cobalt dissolution and 2500 h operation at 1.7 V in a practical PEMWE device. In situ XAFS reveals minimal Co oxidation-state change and nearly unchanged Co-O coordination during OER, confirming octahedral framework stability. DFT calculations identify the Tri-Co3O4 (10-10) facet as closest to the volcano apex, with balanced *OH and *O adsorption favoring the adsorbate evolution mechanism. Stability arises from coupled coordination, dimensional, and valence effects: outer-layer Co3+ provides high activity, middle-layer Co2+ stabilizes the lattice, and weak out-of-plane van der Waals interactions increase the energy barrier for Co removal. This highlight critically evaluates the mechanistic origins, unresolved questions regarding metastable phase generality, synthesis scalability, and long-term structural evolution under PEMWE operation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4477-7
The rapid demand for high-energy-density lithium batteries necessitates advanced solid-state electrolytes (SSEs) to overcome the safety and performance limitations of conventional liquid counterparts. Macrocyclic compounds, with their well-defined cavities, programmable binding sites, and tunable self-assembly, have emerged as powerful molecular regulators for designing next-generation SSEs. This review examines recent advancements in macrocyclic compound-based SSEs by categorizing their functions into four fundamental supramolecular regulation paradigms: cation-centered regulation (e.g., crown ethers), anion-centered regulation (e.g., calixarenes and calixpyrroles), channel-dominated transport (e.g., cyclodextrins), and hybrid regulation (e.g., cucurbiturils). We elucidate how these macrocycles precisely control ion coordination, modulate migration dynamics, and reshape interfacial chemistry, leading to enhanced ionic conductivity, improved Li+ transference numbers, suppressed lithium dendrite growth, and superior interfacial stability. While each paradigm offers distinct advantages, the most promising SSEs often leverage synergistic combinations of these strategies. Finally, we highlight the remaining challenges, including synthetic complexity and multi-objective performance trade-offs, and propose future research directions for developing highly efficient and durable macrocycle-based solid-state lithium batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4257-y
Hafnia-based ferroelectrics exhibit a distinctive reverse size effect and exceptional scalability, positioning them as critical candidates for CMOS-compatible non-volatile memory and ferroelectric transistors, with substantial promise for advancing hardware acceleration in artificial intelligence and large-data storage technologies. However, their practical deployment is constrained by a longstanding dilemma: the difficulty in simultaneously stabilizing metastable polar phases and ensuring long-term reliability under the high electric fields required for polarization switching. This review reinterprets this challenge through the lens of defect physics and advocates a paradigm shift from stochastic, disorder-mediated defect incorporation toward ordered, multiscale defect engineering. We systematically discuss the collective influence of point defects, line defects, planar defects, and defect-coupled structures on the phase stability, switching kinetics, and failure mechanisms in hafnia-based ferroelectrics. Controlling oxygen-vacancy states, engineering dopants via Fermi-level and chemical pressure, deploying periodic dislocation arrays, designing topological domain walls, functionalizing interfaces, and leveraging flexoelectric strain gradients constitute the core strategic toolkit. Through such ordered defect architectures, scalable performance metrics, including high remanent polarization, low coercive field, fast switching speed, and endurance exceeding 10^12 cycles, become attainable. These approaches establish a set of design principles for next-generation low-power, high-reliability ferroelectric electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3773-7
Kesterite Cu2ZnSn(S,Se)4 (CZTSSe) solar cells suffer from significant open-circuit voltage (VOC) deficits due to severe interfacial and bulk recombination, restricting their power conversion efficiency (PCE) far below the Shockley-Queisser limit. This work proposes a low-temperature annealing strategy during ITO sputtering (SA) to synergistically address these challenges. The temperature applied during ITO sputtering not only improves the crystallinity, carrier concentration, and optical transmittance of the ITO layer but also promotes the diffusion of In from ITO into both CdS and CZTSSe layers. Consequently, lattice matching at the CZTSSe/CdS interface is optimized, enabling epitaxial growth. And a favorable ITO/In:CdS/In&Cd:CZTSSe structure with optimal band alignment is obtained. As a result, a champion device with a PCE of 14.29% was achieved. The SA-treating also enabled the CZTSSe solar cells to achieve the highest VOC reported to date, exceeding 590 mV. This underscores the essential role of SA processing in optimizing interface engineering and suppressing defects, thus promoting the development of low-cost, high-performance kesterite photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3747-3
Thermochromic soft materials are flexible functional materials that adaptively tune optical properties (transmittance, reflectance, or scattering) with temperature for thermal modulation. Herein, a laminated thermochromic gel (DEE-DA) is synthesized by encapsulating a thermochromic hydrogel (DA) between two hydrophobic ionogels (DEE) in a stacked configuration. The synergy of multiple dynamic bonds endows the DEE-DA gel with exceptional mechanical properties and remarkable self-healing capability (98.8% at 30 °C). More importantly, attributed to the temperature-responsive reversible cleavage and recombination of hydrogen bonds and borate ester bonds, DEE-DA gel demonstrates tunable transmittance with a light modulation efficiency of 85.45%. In response to the various external conditions, the gel can auto-adjust the optical properties to avoid sun irradiation or heat loss. Accordingly, the gel enables efficient dual-mode thermal modulation across a broad temperature range to realize thermal management. The research proposes gel thermochromism and laminated durability enhancement for adaptive materials in smart buildings and wearables.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3689-9
Converting body heat into electricity presents an appealing route for sustainably powering wearable electronics; however, conventional thermoelectric materials face significant drawbacks, including high ionic concentrations, toxicity, and limited thermoelectric efficiency. Here, we report an ionic thermoelectric hydrogel designed through precise supramolecular chemistry, utilizing dual molecular interactions: host-guest complexation of α-cyclodextrin (α-CD) with I3− ions and hydrogen bonding between polyvinyl alcohol (PVA) polymer chains and I3−. This molecularly tailored approach markedly amplifies thermoelectric performance, achieving a high thermopower of 2.21 mV/K and a tenfold enhancement in peak power output at an exceptionally low iodine concentration (10 mmol/L I− + 2.5 mmol/L I3−). The hydrogel maintains excellent biocompatibility and mechanical robustness, suitable for direct skin contact. Demonstrated applications include flexible thermoelectric devices generating nearly 100 mV from body heat and sensor arrays capable of motion and spatial temperature sensing. These results underscore the substantial potential of supramolecularly designed ionic thermoelectric hydrogels for wearable energy harvesting, personalized healthcare monitoring, and advanced human-computer interfaces.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024122001
Biomass is the only renewable carbon resource with huge reserves and wide sources, and it is green and environmentally friendly. Under the background of 'dual carbon', the clean and efficient utilization of biomass has received increasing attention. Preparation of biochar from biomass is one of the main methods to use biomass efficiently. Biochar surfaces possess porous and aromatic structures, which exhibit good fixation effects on heavy metals in wastewater. However, biochar has shortcomings such as difficulty in recovery and non-reusability. The introduction of iron into biochar can not only enrich surface functional groups, develop pore structure, and increase specific surface area, but also endow magnetic properties, facilitating solid-liquid separation after adsorption. This paper reviews the preparation methods of iron-based magnetic biochar (MBC-Fe), summarizes the effects of different iron sources on its characteristics, and illustrates the adsorption performance and mechanisms of MBC-Fe for typical heavy metals in water. Finally, applications of MBC-Fe in the removal of heavy metal ions from wastewater are concluded, and future utilization potential in other fields is proposed. The review highlights that MBC-Fe exhibits high adsorption capacities, e.g., for Pb(II) and Cd(II), with rapid kinetics and easy separation, making it a promising adsorbent for wastewater treatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3464-4
Photocatalytic conversion of atmospheric CO2 (0.03%) into multi-carbon fuels remains a grand challenge due to the high energy barrier of C–C coupling and the low concentration of CO2. Here, we report the construction of multiple metal pair sites on metal oxide nanosheets to steer C–C coupling, enabling efficient photoreduction of air-concentration CO2 to ethane (C2H6). As a prototype, Au nanoparticles were anchored on Bi4Ti3O12 nanosheets (Au-Bi4Ti3O12). High-resolution transmission electron microscopy and X-ray photoelectron spectroscopy confirmed the formation of Au-Ti metal pair sites at the interface. In situ Fourier transform infrared spectroscopy revealed the presence of *OCCOH intermediate on Au-Bi4Ti3O12 during CO2 photoreduction, which was absent on pristine Bi4Ti3O12. Density functional theory calculations showed that the Gibbs free energy for *CO–COH formation on Au-Bi4Ti3O12 is 2.23 eV, significantly lower than that on Bi4Ti3O12 (3.59 eV), indicating facilitated C–C coupling. Consequently, Au-Bi4Ti3O12 exhibited a C2H6 evolution rate of 2.58 μmol g−1 h−1 under 0.03% CO2, whereas Bi4Ti3O12 produced only C1 products (CO and CH4). This work demonstrates the first single-catalyst photoreduction of atmospheric CO2 to C2H6, highlighting the effectiveness of engineered multiple active sites in overcoming the C–C coupling bottleneck.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3633-5
High-temperature interfacial diffusion in Half-Heusler (HH) thermoelectric devices poses significant challenges for practical applications, particularly the diffusion of Ag from conventional solders, which degrades material performance and device stability. This study reveals anomalous Ag diffusion through a Cr powder barrier layer into Ti0.5Zr0.5NiSn0.98Sb0.02, driven by Sn phase penetration. In contrast, employing a Cr foil barrier layer pre-densified the material, effectively preventing Sn phase penetration and eliminating Ag diffusion pathways, thereby preserving junction integrity. After aging at 973 K for 30 days, the Cr foil junction maintained a clean interface with a low contact resistivity of 0.27 μΩ cm2. Benefiting from this interfacial design, a Hf-free HH module achieved a high conversion efficiency of 10.4% at a hot-side temperature of 976 K, alongside long-term stability. This work addresses critical bottlenecks in developing high-performance, low-cost HH modules, facilitating their commercial application in waste heat recovery.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3931-6
Detection of circularly polarized light (CPL) is crucial for advancing next-generation chiral optoelectronic applications, where a large photocurrent dissymmetry factor (g_Iph) is essential for accurate polarization discrimination. Chiral hybrid perovskites (CHPs) have emerged as promising CPL-active materials owing to their intrinsic spin-orbit coupling and chiroptical properties. However, an intrinsic conflict between g_Iph and photocurrent response remains a major bottleneck in current CHP-based devices. Low-dimensional CHPs typically suffer from limited carrier mobility, while multilayered structures improve carrier transport but generally reduce the chiral component, thereby reducing chiroptical activity and g_Iph. Herein, we report a Cs-based multilayered chiral-polar perovskite, (R-β-MPA)PACsPb2Br7 (1R, MPA=methylphenethylammonium, PA=propylammonium). The distinctive chiral-polar photovoltaic effect in 1R benefits spin-selective carrier separation and collection, and the resulting device achieves self-powered CPL detection with a high g_Iph of 0.5 and maintains excellent polarization selectivity even at ultralow light intensities of 62 nW cm−2. Meanwhile, the multilayered framework enables high responsivity of 71 mA W−1 and detectivity of 6×10^12 Jones (1 Jones = 1 cm Hz^(1/2) W−1) even at zero bias. This work provides a rational design strategy to achieve chiral optoelectronic materials with a high dissymmetry factor and photocurrent response.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025021401
This study investigated the occurrence, distribution, sources, and ecological risks of 19 organophosphate triesters (OPEs) and 8 diesters (di-OPEs) in surface water and sediments from the Hangzhou section of the Qiantang River. Samples were analyzed using liquid chromatography-high resolution mass spectrometry. Concentrations of ΣOPEs in water ranged from 31.5 to 98.9 ng/L, and in sediments from 10.8 to 341 ng/g dry weight (dw). Σdi-OPEs ranged from 2.19 to 104 ng/L in water and 0.437 to 106 ng/g dw in sediments, indicating moderate to low contamination. TCIPP and TCEP dominated OPEs in water, while TEHP was the predominant OPE in sediments. DBP was the major di-OPE in water, and DPHP in sediments. Source apportionment via correlation and principal component analysis identified industrial production and human activities, including household, tire, plastic manufacturing, and agricultural practices, as primary sources. Ecological risk assessment revealed negligible risks for most OPEs in water, but notable risks in sediments: TEHP and EHDPP posed risks to crustaceans, and TPHP to algae. Moreover, combined toxicity at multiple sediment sampling sites raised concern, warranting further attention.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025022501
The pretreatment of trace emerging contaminants in environmental matrices is challenging due to diverse methods and uncertain applicability. This study compared solid-phase extraction (SPE) and liquid-liquid extraction (LLE) for extracting endocrine-disrupting compounds (EDCs), particularly phthalate esters (PAEs), using laboratory-spiked blank samples. LLE achieved satisfactory recoveries for PAEs at spike levels below 4 μg·L−1, enabling detection of five PAEs including diisodecyl phthalate (DIDP), with improved efficiency via repeated extraction. SPE offered lower detection and quantification limits, higher accuracy and sensitivity, and achieved high recoveries for 12 EDCs and 10 antibiotics at spike levels ≥0.2 μg·L−1, with detection limits as low as 0.1–6.4 ng·L−1. The developed SPE coupled with liquid chromatography-Orbitrap mass spectrometry (LC-Orbitrap MS) method was applied to industrial wastewater samples. Across five industrial sectors (coatings, rubber, pharmaceuticals, inks, and materials technology), five antibiotics and ten EDCs were detected, with total concentrations ranging from 0.03–0.56 μg·L−1 and 0.07–1.91 μg·L−1, respectively. Sector-specific profiles emerged: rubber industry effluent was dominated by dibutyl phthalate (DBP) at 1.07 μg·L−1, while pharmaceutical effluent featured sulfamonomethoxine (SMM) at 0.34 μg·L−1. This systematic evaluation demonstrates that SPE-LC-Orbitrap MS is robust for complex matrices, providing a technical foundation for accurate quantification of emerging contaminants in industrial wastewater.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3837-1
The escalating energy crisis and environmental pollution necessitate sustainable catalytic technologies. Piezo-photocatalysis, coupling light and mechanical energy via the piezoelectric effect, has emerged as a promising platform for energy conversion and environmental remediation. This review systematically summarizes recent progress in g-C3N4-based piezo-photocatalysis, addressing the intrinsic limitations of pristine g-C3N4, including weak piezoelectric response, poor low-frequency mechanical response, rapid carrier recombination, and insufficient mechanical stability. Modification strategies such as heterojunction construction, morphology engineering, and element doping are detailed, emphasizing their roles in amplifying internal electric fields and promoting charge separation. The review highlights applications in H2 evolution, H2O2 generation, pollutant degradation, and CO2 photoreduction. Despite achievements, challenges remain in mechanistic understanding and performance optimization. This review provides guidance for rational design of g-C3N4-based piezo-photocatalytic systems, accelerating their deployment in sustainable technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3934-1
Solar energy, a clean and abundant resource, can be stored as latent heat in solid-solid phase change materials (SSPCMs) and subsequently utilized, offering great potential for advancing passive thermal management technologies such as thermal camouflage. Conventional SSPCMs often require active heating for high-temperature conditions, leading to additional energy consumption. Moreover, their permanent crosslinked structures limit reprocessability and increase environmental burden. Herein, we present a lizard-skin-inspired, solar-thermal-responsive, and reprocessable SSPCM (FTSPCM) featuring a dual crosslinked structure composed of dynamic phenol–carbamate bonds and Fe3+@Tannic acid (TA) coordination. Polyethylene glycol (PEG) functions as the phase change segment, while TA introduces both reversible covalent crosslinking and photothermal responsiveness. The FTSPCM exhibits a high latent heat of 102.9 J g−1, excellent shape stability, and maintains its thermal performance after three reprocessing cycles at 120 °C. The Fe3+@TA coordination network enables strong near-infrared absorption and efficient solar-thermal conversion, achieving a surface temperature of 62 °C and a conversion efficiency of 96.85% under 2 Suns irradiation. This dual-function design allows the material to achieve passive thermal camouflage via latent heat release at low temperatures and solar-assisted photothermal heating at high temperatures. This work presents a sustainable strategy for developing reprocessable, solar-responsive SSPCMs, showcasing the distinctive advantages of tannic acid-derived polyphenol chemistry in constructing passive thermal management systems for energy-efficient thermal camouflage and solar-driven thermal energy storage.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3769-2
Proton exchange membrane water electrolyzers (PEMWEs) are pivotal for sustainable hydrogen production, yet the corrosion-induced TiOx on porous transport layers (PTLs) introduces Schottky contact barriers and pinch-off effects, severely impeding charge transfer and efficiency. Here, a cost-effective MoIrOx coating via spray deposition and thermal treatment on Ti felts is proposed. The coating forms a conductive interlayer that establishes a Schottky barrier staircase, reducing the effective electron transfer barrier and isolating TiOx from the ionomer to mitigate the pinch-off effect. The optimal PTL achieves a current density of 3.27 A cm−2 at 2 V, surpassing uncoated Ti felts by 59.5%. The MoIrOx interlayer suppresses localized electron accumulation at the interface, enabling stable operation with ultra-low catalyst loadings by preventing direct ionomer-TiOx contact. This work demonstrates a scalable strategy to enhance PEMWE efficiency and durability while minimizing precious metal reliance, offering critical insights into interface engineering for electrolyzers.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3776-9
Organic thin-film transistors (OTFTs) are fundamental building blocks for flexible electronics, offering mechanical flexibility, biocompatibility, chemical tunability, and compatibility with large-area, cost-effective fabrication. However, their widespread adoption in high-density integrated systems is hindered by the thermionic limit of carrier injection, which constrains the subthreshold swing (SS) to a minimum of 60 mV/dec at room temperature, posing a critical barrier to ultra-low-power operation. In a groundbreaking study published in Nature Electronics, Deng et al. report the realization of organic thin-film tunnel transistors (OTFTTs) that decisively break this Boltzmann tyranny. The breakthrough is enabled by an interfacial molecule decoupling strategy, introducing a high-ionization-energy molecular interlayer, N,N'-bis(2-phenylethyl)perylene-3,4:9,10-tetracarboxylic diimide (BPE-PTCDI), between the high-work-function metal oxide (MoO3) source and the p-type organic semiconductor (2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT)) channel. This interlayer passivates the interface, minimizing interfacial gap states and alleviating Fermi-level pinning, thereby creating a clean heterojunction with a lowered tunneling barrier. This facilitates efficient quantum mechanical band-to-band tunneling for carrier injection at low supply voltages, instead of relying on traditional thermionic emission. The OTFTTs exhibit sub-thermionic SS values below 60 mV/dec, enabling high electrical performance at low operating voltages. This work provides a viable pathway for beyond-thermionic electronics, with potential applications in flexible displays, wearable health monitors, brain-computer interfaces, and distributed sensor networks, addressing the critical challenge of power dissipation in flexible systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-3961-8
This correction addresses an inadvertent misplacement of Fig. 4b3 during figure reorganization in the original article published in Science China Materials, volume 65, issue 10, 2022, page 2850 (DOI: 10.1007/s40843-022-2024-6). The corrected Fig. 4b is presented herein. The authors confirm that this correction does not affect the results, conclusions, text, or figure caption of the original work. The correction was requested by the authors and received on 6 January 2026, accepted on 8 January 2026, and published online on 10 February 2026. The original study introduced flexible electrostatic hydrogels derived from marine organisms for nitric oxide-enhanced photodynamic therapy against multidrug-resistant bacterial infections. The correction ensures the accurate representation of experimental data, maintaining the integrity of the scientific record.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60615-3
Co-pyrolysis of oil-rich coal and biomass is a promising route to enhance oil and gas production, yet the underlying synergistic mechanisms remain poorly understood. This study investigates the effect of hydrothermal pretreatment (HTP) on the co-pyrolysis of Huangling coal (H) and enzymatic hydrolysis lignin (E). Raw and pretreated samples were characterized via proximate/ultimate analysis, SEM, ICP-OES, and 13C-NMR. Fixed-bed pyrolysis experiments were conducted to evaluate synergistic performance. Results show that HTP reduces oxygen content, develops pore structure, and increases concentrations of inorganic metal ions (Ca, K, Fe) in the aqueous phase. Structural modifications bring the carbon skeleton of E closer to that of H, with increased bridge carbon ratio and improved thermal stability, aligning pyrolysis temperature ranges. For the H/E blend (8:2) after 24 h HTP, tar yield increases by 80.52% compared to untreated blend, with significant rises in aliphatic compounds and monocyclic aromatic hydrocarbons. Gas yields of H2, CO, and CH4 increase by 5.47%, 10.98%, and 9.27%, respectively, while CO2 and pyrolysis water generation are inhibited (water yield decreases by 93.98%). Semi-coke pore structure becomes more developed. The enhanced synergistic effect is attributed to a multi-fold mechanism of 'component interaction-structural modification-catalytic cracking'. These findings provide theoretical support for developing technologies to improve co-pyrolysis of oil-rich coal and biomass, advancing low-carbon, high-quality utilization.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0037
Alumina microspheres with a lamellar-assembled flower-like morphology were synthesized via a urea-assisted hydrothermal method and used as supports to prepare Pd/Al2O3-M catalysts by incipient wetness impregnation. The catalytic performance was evaluated in the selective hydrogenation of isoprene and the hydrogenation of 2-ethylanthraquinone for hydrogen peroxide production, and compared with a commercial alumina-supported Pd catalyst (Pd/Al2O3). Characterization revealed that the flower-like structure, composed of stacked nanosheets, promoted high Pd dispersion and enhanced metal-support interaction, leading to a higher surface Pd content and more abundant active sites. Under 60 °C and 1 MPa H2, Pd/Al2O3-M achieved 95.2% conversion of isoprene with 98.3% total selectivity to isoamylenes, and exhibited good stability over 24 h. In anthraquinone hydrogenation, it reached a hydrogenation efficiency of 15.8 g/L, a 27.4% improvement over Pd/Al2O3 (12.4 g/L). The study demonstrates that modulating carrier morphology is an effective strategy to simultaneously enhance activity, selectivity, and stability of Pd catalysts, offering a promising approach for designing efficient hydrogenation catalysts.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607014
Reducing ammonia emissions and recovering lost nitrogen are critical for enhancing nitrogen content in compost. Biological trickling filters, as end-of-pipe odor control, retain ammonia nitrogen in effluent, offering a reuse pathway. However, the impact of nitrogen-rich wastewater reuse within the optimal C/N range (20.0:1–30.0:1) remains unclear. This study composted biogas residue, sawdust, food waste, and mushroom residue, setting initial C/N as the control variable. Four groups were established: low C/N with nitrogen-rich wastewater (LRN), low C/N with deionized water (LRW), high C/N with nitrogen-rich wastewater (HRN), and high C/N with deionized water (HRW). Simulated wastewater (2000 mg/L NH4+-N and 2000 mg/L NO2−-N) was recycled. Results showed no inhibition of final maturity; pH (8.17–8.48) and seed germination index (GI) (90.85%–122.96%) met organic fertilizer standards. HRN reduced cumulative total greenhouse gases, N2O, and NH3 by 20.32%–30.35%, 0.67%–53.38%, and 52.14%–62.15% compared to LRN and LRW. Although HRN emissions were slightly higher than HRW (total GHGs +4.56%, NH3 +4.99%), HRN final nitrogen content (4691.27 mg/kg) exceeded HRW (4514.96 mg/kg), attributed to sufficient carbon enhancing microbial assimilation. Conversely, low C/N with nitrogen-rich wastewater increased NH3 and N2O emissions (LRN vs LRW: +26.43% and +112.99%) due to carbon limitation. Thus, high initial C/N with nitrogen-rich wastewater reuse effectively reduces gaseous nitrogen loss and greenhouse gas emissions while maintaining compost maturity.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4012-4
Stimuli-responsive fluorescent hydrogels, owing to their tunable optical properties and unique smart response characteristics, have significant potential in encryption applications and information security. However, most current systems are limited to single-stimulus responsiveness and lack the capability for programmable information erasure or multi-modal dynamic synergy. Hence, we propose a multi-stimuli-responsive phase-change hydrogel incorporating aggregation-induced emission hydrophobic carbon dots (AIE-HCDs) and polyethylene glycol (PEG)-cellulose network, demonstrating dynamic fluorescence chromism under various external triggers. The hydrogel exhibits solvent-exchange-triggered fluorescence color changes from blue to red, enabled by the concentration modulation of AIE-HCDs through the exchange between PEG and water. Additionally, the temperature-induced phase transition of PEG from crystalline to molten state modulates the aggregation and dispersion of AIE-HCDs, thereby enabling dynamic fluorescence color changes. The phase transition further confers excellent shape-memory behavior and adjustable mechanical properties, with the tensile modulus varying from 6.28 MPa in the molten state to 36.23 MPa in the crystalline state, while maintaining high transparency (~88% in the molten state). By utilizing micro-contact printing and the multi-stimulus response, an encryption platform enables information to be hidden, selectively read under sequential stimuli (thermal, UV, and solvent), and completely erased upon demand. This strategy demonstrates significant potential for advancing high-level information encryption and anti-counterfeiting technologies.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60762-1
The CO2 dry reforming of methane (DRM) is pivotal for CO2 utilization within the dual-carbon framework, offering advantages in carbon reduction and value-added chemical production. However, shaped catalysts suitable for industrial-scale DRM remain limited. This work constructs a monolithic catalyst using honeycomb cordierite as the structural support, systematically investigating the effects of organic and inorganic binders on coating structure and catalytic performance. Comparative studies reveal that the active coating fabricated with inorganic aluminum sol exhibits a continuous uniform morphology and excellent adhesion strength. During high-temperature calcination, elemental diffusion within Al2O3 networks bridges the cordierite surface with active catalyst particles, forming a (Ni-Mg)AlxO4 composite structure. This creates robust metal-support interactions between active sites and the residual alumina matrix. The interconnected mesoporous framework provides superior pore confinement, contributing to strong coating adhesion, enhanced activity, and improved resistance to carbon deposition in the monolithic m-NCM-Al-sol catalyst. In contrast, coatings derived from inorganic silica sol suffer from detachment and activity loss due to heterogeneous surface structures and poor adhesion. Organic binders demonstrate inferior performance in macroscopic coating uniformity, adhesion strength, mesoporous confinement, and localized electronic effects, resulting in the poorest catalytic performance. By optimizing aluminum sol coating parameters—binder content, active component dosage, and coating cycles—a synergistic balance between coating thickness and mass transfer is achieved. The optimized catalyst demonstrates excellent DRM performance, providing insights for constructing high-performance shaped catalysts with cordierite coatings.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025041505
To combat severe air pollution, China has implemented a series of air pollution control action plans since 2013, effectively alleviating PM2.5 pollution. However, PM2.5 concentrations in most cities within the Fenwei Plain still exceed national standards. This study systematically evaluates PM2.5 concentration changes across two policy phases (2013–2020) using the Community Multiscale Air Quality (CMAQ) model, quantifying contributions of meteorology and emissions, and analyzing sectoral source changes. Results show that annual average PM2.5 concentration declined cumulatively by 19% during 2013–2020. In the first phase (2013–2017), regional PM2.5 decreased by 3% annually, with most improvement in winter; however, due to unfavorable meteorology, concentrations increased in Xi'an and Xianyang. In the second phase (2017–2020), PM2.5 declined by an additional 16%, with more effective control measures, particularly in spring and autumn. Emission reductions dominated in both phases, with stronger effects in the second phase (−8 μg·m−3), significantly outweighing adverse meteorological contributions (+3.5 μg·m−3). Nevertheless, many cities still face challenges from unfavorable meteorology, highlighting the need for future policies to account for meteorological influences. Emissions from industrial, energy, and agricultural sources decreased significantly across both phases. However, during winter heating periods, residential emissions emerged as a source equal in importance to industrial emissions, becoming a key target for future emission controls.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3994-9
Electrokinetics, the study of charge transfer and mass transport under electric fields, is fundamental to advancing energy storage and electrocatalysis. Organic-inorganic composite materials synergistically combine the structural stability and conductivity of inorganic phases with the functional diversity of organic components, optimizing electrokinetic properties such as charge transfer, ionic mobility, and catalytic activity. This review systematically examines the intersection of electrokinetic phenomena and organic-inorganic composites, focusing on fundamental principles, design strategies, and performance optimization. Advanced materials including metal-organic frameworks (MOFs), organic-carbon hybrids, and single-atom catalysts are highlighted, with applications spanning batteries, fuel cells, wearable devices, and electrocatalytic systems. Emphasis is placed on advanced in situ and operando characterization techniques that probe electrokinetic processes, revealing the interplay between structure, interface, and transport dynamics. By bridging electrokinetic theory and material design, this work provides a roadmap for developing next-generation materials for sustainable energy technologies. The review consolidates recent progress, identifies remaining challenges, and proposes future directions for leveraging electrokinetic principles to achieve high-efficiency, durable energy systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4055-6
The global pursuit of clean energy and environmental remediation has intensified research into solar-driven photocatalysis, with g-C3N4 emerging as a leading metal-free polymer semiconductor. Between 2020 and 2025, significant advances have been achieved in overcoming the inherent limitations of pristine g-C3N4, such as restricted light absorption (wavelengths <460 nm), rapid charge recombination, and insufficient active sites, through sophisticated modification strategies. This period has witnessed the refined development of elemental doping, defect engineering, heterostructure construction, and cocatalyst loading, each playing a critical role in enhancing optical properties, charge separation efficiency, and surface reactivity. Contemporary research increasingly focuses on band structure precision engineering, interfacial charge transfer pathways, and defect-mediated catalytic mechanisms. These developments are underpinned by advanced characterization techniques, including X-ray absorption spectroscopy, in-situ Fourier transform infrared spectroscopy, femtosecond transient absorption spectroscopy, Kelvin probe force microscopy, in-situ X-ray photoelectron spectroscopy, and electron paramagnetic resonance. Looking forward, emerging trends such as AI-guided material design, atomic-scale defect control, and operando analysis are shaping the next generation of high-efficiency g-C3N4 photocatalysts, offering a promising outlook for their application in sustainable energy conversion and environmental remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4144-y
Developing efficient strategies for electrically manipulating two-dimensional magnetism at room temperature is a key challenge in contemporary spintronics. In this study, we demonstrate giant electromechanical control over the magnetism of the room-temperature van der Waals ferromagnet Fe3GaTe2 by integrating it with the ferroelectric α-In2Se3. Modest gate voltages lead to an almost complete suppression of the coercive field by 96.5%, corresponding to a remarkable peak modulation sensitivity of ~8.1 mT V−1, which stands out among existing van der Waals magnetoelectric systems. Importantly, this substantial magnetoelectric response is predominantly unaffected by voltage polarity, as both positive and negative gate voltages induce similar magnetic modulation effects. To elucidate the underlying mechanism, we tracked the voltage-induced Raman spectral changes, revealing a peak shift of 1.7 cm−1 that accurately represents an effective in-plane tensile strain of ~1.42% under an equivalent bias, demonstrating polarity independence as well. The synchronized magnetic response and strain variation unequivocally indicate that the induced tensile strain serves as the fundamental physical driver behind the magnetic modulation. Additionally, density functional theory calculations corroborate that the reduction in magnetic anisotropy induced by tensile strain results in a decrease in the coercive field. Our work establishes a novel and efficient approach for achieving voltage control of magnetism at room temperature in van der Waals multiferroic heterostructures, highlighting their significant potential for applications in ultra-low-power magnetic logic and sensing technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4031-6
Organic fluorophores operating in the second near-infrared (NIR-II, 1000–1700 nm) window are highly attractive for cancer phototheranostics. Yet, the advancement of aza-BODIPY-based NIR-II dyes remains challenging due to their limited spectral tunability and diminished fluorescence quantum yields (FLQY) under physiological conditions. Herein, we propose a rational donor-acceptor (D-A) molecular engineering strategy to construct an aza-BODIPY fluorophore, TPACN, featuring intramolecular charge transfer (ICT)-enhanced NIR-II emission and balanced photothermal performance. By introducing electron-rich triphenylamine (TPA) donors and peripheral cyano (–CN) acceptors, the optimized D-A coupling significantly strengthened the ICT effect, leading to broadened NIR absorption, a markedly red-shifted fluorescence peak at 1086 nm, and an exceptional fluorescence quantum yield of 1.55% in dichloromethane (DCM). When encapsulated in F127, TPACN nanoparticles (TPACN NPs) maintained a high aqueous FLQY of 0.20%, accompanied by a notable photothermal conversion efficiency (PCE) of 39% under 808 nm irradiation. The sterically twisted TPA units effectively alleviated aggregation-caused quenching (ACQ) and fine-tuned the excited-state energy dissipation pathways, realizing a synergistic balance between radiative (fluorescence) and non-radiative (heat) relaxation. Benefiting from these optimized photophysical properties, TPACN NPs achieved high-resolution NIR-I photoacoustic and NIR-II fluorescence dual-modal imaging, enabling accurate tumor visualization and efficient photothermal ablation in vivo. This work introduces a general design paradigm that exploits ICT modulation and steric engineering to overcome the intrinsic fluorescence bottleneck of aza-BODIPY systems, offering new molecular insights for the advancement of high-performance NIR-II dyes for precision phototheranostics.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3643-8
Inverted perovskite solar cells (PSCs) suffer from defect-mediated nonradiative recombination and inefficient charge extraction, particularly at the buried interface and grain boundaries (GBs), which limit power conversion efficiency (PCE) and operational stability. This study introduces a multifunctional phosphonic acid molecule, (2-(3,6-bis(trifluoromethoxy)-9H-carbazol-9-yl)ethyl)phosphonic acid (M28), as an additive in the perovskite precursor solution. M28 spontaneously segregates toward the buried interface and GBs, fulfilling three roles: (1) slowing crystallization to enlarge grains and improve film quality, (2) passivating defects to suppress charge recombination, and (3) inducing p-type doping to create an extra electric field that promotes hole transport. Devices incorporating M28 achieve a champion PCE of 25.96% and retain 80% of initial efficiency after 1500 h of maximum power point tracking. This work demonstrates the efficacy of multifunctional phosphonic acid additives in addressing buried-interface and GB defects, offering a viable route to high-performance, stable inverted PSCs.