SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4312-8
Carbazole phosphonic acid-based self-assembled molecules (SAMs) serve as effective hole-selective contacts in organic solar cells (OSCs), yet their molecular packing and aggregation behavior during solution processing remain difficult to control, limiting hole transport and device durability. This study introduces a polymer-templated self-assembly strategy to regulate molecular organization by one-step spin-coating a blend of [2-(9H-carbazol-9-yl)ethyl]phosphonic acid (2PACz) and PEDOT:PSS. The polycationic PEDOT+ framework acts as a template, providing supplementary anchoring interactions that promote ordered molecular arrangement and suppress unfavorable agglomeration. Pronounced face-on orientation and enhanced structural coherence of 2PACz within the polymer matrix are evidenced. The templated ordering improves vertical charge transport, interfacial homogeneity, and film morphology. In binary OSCs based on PM6:BTP-eC9, the hybrid hole transport layers (HTLs) yield a champion power conversion efficiency (PCE) of 20.26%, with an open-circuit voltage (VOC) of 0.874 V, a short-circuit current (JSC) of 28.97 mA cm-2, and a fill factor (FF) of 80.02%. Devices incorporating hybrid HTLs exhibit exceptional operational stability, retaining over 90% of initial PCE (T90) after 405 h of continuous operation at the maximum power point (MPP). This work establishes polymer-directed SAM assembly as a scalable route to simultaneously optimize nanoscale molecular packing, interfacial energetics, and long-term device stability for high-performance OSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4415-3
The escalating demands of military stealth platforms and the proliferation of electromagnetic pollution have intensified the need for high-performance electromagnetic wave (EMW) absorbers. Nanofibers, characterized by high specific surface area and favorable composite compatibility, are engineered into absorbers with outstanding electromagnetic properties. This review consolidates the preparation and optimization strategies for nanofiber-based absorbers. The electromagnetic attenuation mechanisms are first outlined, followed by a systematic classification of nanofiber fabrication methods into two principal categories: in-situ synthesis and electrospinning-derived processes. Recent advances in optimization strategies for absorbers constructed from nanofibers with tailored electromagnetic characteristics are then examined. The review draws upon representative studies, including ultrathin and flexible electromagnetic interference shielding films via interface-confinement, design strategies for wave-absorbing polymer-based shielding materials, impedance-matchable 3D MXene sponge/NiFe@NC heterostructures with tunable pores, and the influence of fiber coating on SiCf/epoxy composites. These works collectively demonstrate the critical role of fiber architecture, interface engineering, and impedance matching in determining absorption performance. The analysis identifies persistent challenges in scalability, cost, and environmental stability, and outlines future prospects for nanofiber-based EMW absorbers. This review provides a foundational reference for researchers and engineers seeking to translate nanofiber absorber concepts into deployable stealth and pollution-mitigation technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4480-1
Ternary organic solar cells (OSCs) incorporating a structurally compatible guest acceptor (C7-Cl) into the PM6:BTP-eC9 host system are demonstrated. The low Flory-Huggins interaction parameter between host and guest acceptors facilitates intimate mixing, optimizing molecular packing and energy-level alignment. High-sensitivity sEQE and EQEEL analyses reveal a reduced non-radiative energy loss (KE3) of 0.216 eV in the ternary device. Consequently, the optimized ternary OSC achieves a champion power conversion efficiency (PCE) of 20.02% and an improved T80 operational lifetime of 1065 h. This work establishes a feasible strategy via structurally compatible guest doping to simultaneously optimize vertical phase separation and suppress non-radiative loss, providing a facile and effective route toward high-performance and stable OSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4309-8
Iridium-doped cobalt oxide nanosheets derived from a ZIF template were evaluated as oxygen evolution reaction (OER) catalysts for proton exchange membrane water electrolysis (PEMWE). Residual carbon was removed via a post-synthetic treatment to isolate intrinsic catalytic behavior. The Ir0.23Co0.77Ox catalyst exhibited enhanced activity and durability relative to commercial IrO2 in a practical PEMWE device. Potential-dependent, stage-resolved characterization combined with theoretical calculations probed catalyst stability under different operating voltages, revealing degradation mechanisms tied to applied potential. Contact angle measurements showed that the Ir0.23Co0.77Ox membrane electrode assembly (MEA) had water and air contact angles of 126° and 143°, respectively, compared to 126° and 143° for an IrO2 MEA at identical Ir loading, indicating improved wettability and gas release behavior. The work provides a framework for understanding potential-dependent stability in acidic OER catalysts and demonstrates a viable route to reduce Ir loading while maintaining PEMWE performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4179-x
Perylene diimide (PDI) radical anions exhibit poor environmental stability, restricting their generation efficiency and practical application. Here, a PDI-functionalized bispillar[5]arene (PDI-P5) was designed to construct stable and high-efficiency photothermal radicals. Intramolecular charge transfer (ICT) between PDI and bispillar[5]arene narrows the energy gap. Under 455 nm ultraviolet light irradiation and diethylamine (DEA) vapor exposure, photoinduced electron transfer (PET) efficiently generates PDI-P5·− radicals, which possess broad near-infrared (NIR) absorption, enhanced non-radiative transitions, and excellent stability. Notably, PDI-P5·− can rapidly reach 90 °C under 0.20 W cm−2 simulated sunlight irradiation. Moreover, it exhibits superior multi-step photothermal anti-counterfeiting performance. This work provides a novel strategy for the development of stable radical-based photothermal materials, which holds great potential for anti-counterfeiting and bioimaging applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3722-3
Magnesium alloys are promising biodegradable bone implant materials due to their biocompatibility and mechanical compatibility, but rapid degradation and postoperative bacterial infection limit clinical application. Here, zeolitic imidazolate framework-8 (ZIF-8) and 3,4,9,10-perylenetetracarboxylic diimide (PD) composite coatings (ZIF-8@PD) were fabricated in situ on micro-arc oxidation (MAO) coated AZ31 alloys via two-step and one-step (OS) methods. The MAO/ZIF-8@PD and MAO/ZIF-8@PD (OS) coatings reduced corrosion current density by three and two orders of magnitude, respectively, compared to MAO coating, due to the physical barrier of the 2D-co-3D MOF structure. Under 808 nm near-infrared laser irradiation, photothermal and photodynamic effects from PD, combined with contact killing by released Zn2+ ions, achieved bactericidal rates ≥99.5% against E. coli and S. aureus. Photothermal conversion efficiencies were 44.01% and 48.57% for the two-step and one-step coatings, respectively. The distinct Zn2+ sources led to different 2D-co-3D MOF structures, influencing degradation and antibacterial behavior. These coatings offer a strategy to enhance corrosion resistance and antibacterial activity of Mg alloys for biomedical applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3838-5
Air-permeable and ultrathin conductive electrodes are essential for next-generation soft electronics, including breathable wearables, on-skin devices, and bio-integrated electronics. However, conventional metallization strategies, such as sputtering and ink-printing, often suffer from severe vertical charge leakage due to the porous and ultrathin characteristics of nanofibrous networks, leading to device short-circuiting, operational failure, and limited vertical integration. Here, we present a solvent-selective dissolution-assisted transfer printing strategy to achieve surface-confined metallization of ultrathin, lightweight, and gas-permeable nanofibrous networks, enabling lateral conductivity while maintaining vertical insulation. This transfer printing process facilitates not only the rapid formation of conductive patterns on the surface of nanofibrous networks but also mechanical reinforcement through solvent evaporation-induced interlocked fiber-fiber welding. Meanwhile, the strategy preserves the high permeability of the nanofibrous networks and imparts a unique combination of surface conductivity (2 Ω cm) and vertical insulativity (10^11 Ω cm). The resulting anisotropic conductive networks enable low-voltage wearable heaters, high-sensitive pressure sensors, and ultralight temperature sensors. A pressure-temperature dual-modal sensing patch is further fabricated for intelligent grasping classification. The proposed surface-confined metallization strategy enables rapid fabrication of an anisotropic conductive network as a building block to construct air-permeable, ultrathin, and lightweight wearable electronics.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010701
This study investigated the long-term effects of biochar application on physicochemical properties and microplastic accumulation in aeolian sandy soils, based on a field experiment established in 2014. After seven years of mulched cultivation, soil samples were collected from 0–30 cm and 30–60 cm depths. Biochar application significantly increased soil porosity and available nitrogen, phosphorus, and potassium contents, while reducing bulk density. At a biochar rate of 126.00 t·hm−2, soil water content was significantly reduced. Microplastic abundance averaged 3459.57 pieces·kg−1 in the 0–30 cm layer, with the highest abundance at 126.00 t·hm−2; in the 30–60 cm layer, average abundance was 3163.50 pieces·kg−1, with the highest at 63.00 t·hm−2. Microplastics were predominantly transparent, film-shaped, and 0–0.5 mm in size. The results indicate that biochar application significantly increased microplastic abundance in aeolian sandy soils, providing insights into microplastic adsorption and enrichment in agricultural ecosystems. Further research is needed to elucidate underlying mechanisms.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3804-7
Supramolecular helical architectures hold promise for enantioselective catalysis, yet the influence of screw pitch on catalytic performance remains underexplored. Here, we report the construction of right-/left-handed helical nanoribbons (P/M-DAIPA) based on 5-aminoisophthalic acid dimer (DAIPA). Through an alcohol-mediated self-assembly strategy, the average screw pitch was tuned from 360 to 3152 nm. Mechanistic studies revealed that hydrogen-bonding interactions between DAIPA, modulated by alcohol identity and alcohol/water ratios, dictate helical morphology and pitch. Encapsulation of Fe3O4 nanoparticles yielded P-DAIPA-Fe3O4 and M-DAIPA-Fe3O4 nanozymes, which exhibited higher catalytic efficiency toward S-3,4-dihydroxyphenylalanine (DOPA) and R-DOPA, respectively. Notably, catalytic enantioselectivity inversely correlated with screw pitch, achieving selectivity factors from 1.52 to 2.01. Experimental evidence demonstrated that shorter screw pitch enhances adsorption enantioselectivity of R/S-DOPA on the nanozymes, providing mechanistic insight into pitch-dependent asymmetric catalysis. This work deciphers solvent-driven control of supramolecular screw pitch and establishes a framework for engineering chiral nanozymes with tunable enantioselectivity, advancing enantioselective synthesis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3934-1
Solar energy, a clean and abundant resource, can be stored as latent heat in solid-solid phase change materials (SSPCMs) and subsequently utilized, offering great potential for advancing passive thermal management technologies such as thermal camouflage. Conventional SSPCMs often require active heating for high-temperature conditions, leading to additional energy consumption. Moreover, their permanent crosslinked structures limit reprocessability and increase environmental burden. Herein, we present a lizard-skin-inspired, solar-thermal-responsive, and reprocessable SSPCM (FTSPCM) featuring a dual crosslinked structure composed of dynamic phenol–carbamate bonds and Fe3+@Tannic acid (TA) coordination. Polyethylene glycol (PEG) functions as the phase change segment, while TA introduces both reversible covalent crosslinking and photothermal responsiveness. The FTSPCM exhibits a high latent heat of 102.9 J g−1, excellent shape stability, and maintains its thermal performance after three reprocessing cycles at 120 °C. The Fe3+@TA coordination network enables strong near-infrared absorption and efficient solar-thermal conversion, achieving a surface temperature of 62 °C and a conversion efficiency of 96.85% under 2 Suns irradiation. This dual-function design allows the material to achieve passive thermal camouflage via latent heat release at low temperatures and solar-assisted photothermal heating at high temperatures. This work presents a sustainable strategy for developing reprocessable, solar-responsive SSPCMs, showcasing the distinctive advantages of tannic acid-derived polyphenol chemistry in constructing passive thermal management systems for energy-efficient thermal camouflage and solar-driven thermal energy storage.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3903-4
Cross-wavelength near-perfect light capture technology is crucial in various fields, including spectroscopy, energy conversion, and electromagnetic control. Nevertheless, the primary challenge in broadband absorption is effectively coordinating the intrinsic response behavior of various electromagnetic waves across the nanometer-centimeter scale when interacting with matter. By adopting a multi-scale structural design strategy, the carbon-zirconium heterointerface is integrated into the macroscopic periodic unit cell (PUC) to develop an ultra-wideband light capture material. The optical coupling effect, strengthened by electronic transitions, molecular motion, and spatial scattering effects, endows ZC-PUC with exceptional light-capture performance ranging from ultraviolet to microwave frequencies. Specifically, the ZC-PUC absorber possesses a near-perfect absorption rate of 95.7% across the ultraviolet-visible-infrared spectrum (190–2500 nm), and an effective absorption coverage of 99.99% in the microwave and terahertz bands (1997.9 GHz). More importantly, the as-prepared material maintains the morphology structure and physical phase even when exposed to an alkaline or acidic environment for 365 days and simultaneously possesses stable light capture properties. The easily scalable approach retains excellent structural stability and ultra-wideband light trapping capability under extreme conditions, offering a versatile platform for the development of next-generation devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4012-4
Stimuli-responsive fluorescent hydrogels, owing to their tunable optical properties and unique smart response characteristics, have significant potential in encryption applications and information security. However, most current systems are limited to single-stimulus responsiveness and lack the capability for programmable information erasure or multi-modal dynamic synergy. Hence, we propose a multi-stimuli-responsive phase-change hydrogel incorporating aggregation-induced emission hydrophobic carbon dots (AIE-HCDs) and polyethylene glycol (PEG)-cellulose network, demonstrating dynamic fluorescence chromism under various external triggers. The hydrogel exhibits solvent-exchange-triggered fluorescence color changes from blue to red, enabled by the concentration modulation of AIE-HCDs through the exchange between PEG and water. Additionally, the temperature-induced phase transition of PEG from crystalline to molten state modulates the aggregation and dispersion of AIE-HCDs, thereby enabling dynamic fluorescence color changes. The phase transition further confers excellent shape-memory behavior and adjustable mechanical properties, with the tensile modulus varying from 6.28 MPa in the molten state to 36.23 MPa in the crystalline state, while maintaining high transparency (~88% in the molten state). By utilizing micro-contact printing and the multi-stimulus response, an encryption platform enables information to be hidden, selectively read under sequential stimuli (thermal, UV, and solvent), and completely erased upon demand. This strategy demonstrates significant potential for advancing high-level information encryption and anti-counterfeiting technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4037-1
Nasopharyngeal carcinoma (NPC) poses a therapeutic challenge due to its anatomical complexity and the limitations of conventional treatments in achieving precise targeting and sufficient efficacy. Here, we report a multifunctional platform based on heat-triggered electrospray self-healing porous poly(lactic-co-glycolic acid) (PLGA) microspheres encapsulating indocyanine green (ICG), sequentially coated with a tannic acid-Fe3+ (TAF) metal-phenolic network and fibronectin (FN) for targeted photothermal/chemodynamic combination therapy. The resulting functional microspheres (PI-TAF@FN) exhibit an average size of 1.9 μm, excellent colloidal stability, heat-induced self-healing performance, and a high photothermal conversion efficiency of 51.4%. These microspheres specifically target NPC cells via FN-mediated integrin recognition, enabling ICG/TAF-mediated photothermal therapy under 808-nm laser irradiation and TAF-mediated chemodynamic therapy, leading to enhanced cancer cell apoptosis in vitro. In a mouse NPC model, the combined photothermo-chemodynamic therapy achieved effective tumor treatment with minimal systemic toxicity. Furthermore, the dual TAF and ICG components allow multimode FN-targeted T1-weighted magnetic resonance/fluorescence/thermal imaging for precision NPC management. This electrospray self-healing porous microsphere platform offers a unique theranostic strategy that can integrate diverse therapeutic and diagnostic components for precision oncology.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4052-0
Cutaneous wound infections affect millions of patients annually worldwide, and early diagnosis is critical for timely anti-infection treatment. Bacterial infections alter wound pH, offering a promising diagnostic approach. Here, a diagnostic smart dressing (CMC-PDBI) is developed by ultraviolet-initiated crosslinking of a pH-responsive indicator coating, incorporating modified bromothymol blue, onto a carboxymethyl cellulose substrate. The dressing exhibits superior pH-triggered color-changing performance in both phosphate buffer solution and bacterial cultures across the pH range associated with wound infection (orange at pH 6.0, green from pH 6.5 to 7.5, blue at pH 8.0). In a murine wound infection model, CMC-PDBI indicates infection two days before symptomatic manifestation. Early therapy guided by the dressing accelerates wound healing and reduces inflammation. A smartphone application (InfectSense) assists in identifying infection risk. This work presents a novel early-warning platform for qualitative visual diagnosis of wound infections before clinical symptom onset, with high potential for clinical and home care settings.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3631-1
Anion exchange membrane water electrolysis (AEMWE) offers cost and dynamic-response advantages over proton exchange membrane systems, yet commercial deployment is constrained by the alkaline stability of anion exchange membranes (AEMs) and the sluggish kinetics of non-precious metal catalysts. This work reports a series of poly(terphenyl-diphenylmethane piperidinium) (QPDPMTP) membranes synthesized with varied diphenylmethane (DPM) content. The alkyl chain of DPM induces pronounced microphase separation and elevates free volume fraction, yielding an OH− conductivity of 152 mS cm−1 at 80 °C for QPDPMTP-10. After 1032 h immersion in 6 M NaOH at 80 °C, the membrane retains 90.7% of its initial conductivity. An AEMWE cell integrating QPDPMTP-10 with a non-precious NiFeCo LDH/NiS/NF anode achieves 3.11 A cm−2 at 2 V in 1 M KOH at 80 °C and sustains 1 A cm−2 for 1800 h under gradient KOH concentration. These results establish a viable pathway for durable, low-cost AEMWE systems.