SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4277-1
Two-dimensional (2D) magnetic materials hold promise for next-generation spintronics, yet most exhibit Curie temperatures (Tc) far below room temperature, limiting practical applications. Here, we report the realization of room-temperature ferromagnetism in CuCrSe2 nanosheets via controlled anion removal achieved by post-synthetic vacuum annealing. Raw CuCrSe2 shows a low Tc of ~120 K, whereas annealed CuCrSe2 (A-CuCrSe2) nanosheets exhibit robust ferromagnetic ordering above 300 K. Structural and compositional analyses, including transmission electron microscopy, Raman spectroscopy, and X-ray absorption spectroscopy, confirm that A-CuCrSe2 retains the original layered crystal structure with an estimated Se vacancy concentration of approximately 10%. Magnetic measurements reveal room-temperature ferromagnetism in exfoliated nanosheets, corroborated by magnetic imaging and electric transport measurements. Anomalous Hall effect (AHE) measurements uncover the coexistence of two ferromagnetic phases within the same sample: one with low Tc (~120 K) and another with high Tc (>300 K), indicating spatially heterogeneous magnetic ordering driven by anion removal distribution. Density functional theory (DFT) calculations elucidate the microscopic mechanism, suggesting that Se vacancies modulate the magnetic exchange interactions, enhancing Tc. This work demonstrates that anion modulation is an effective intrinsic strategy to achieve room-temperature ferromagnetism in 2D materials, potentially advancing spintronic applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3605-0
Nickel oxide (NiOx) is widely used as a hole transport material in inverted perovskite solar cells (PSCs). However, its practical application is limited by low intrinsic conductivity and insufficient hole extraction ability, leading to significant interfacial defects that reduce device efficiency and stability. To overcome these issues, two isomeric small organic molecules, 2,6-NOT and 1,5-NOT, were developed and introduced to modify NiOx. These isomers share the same structure but differ in the substitution positions of functional groups, resulting in distinct molecular planarity. Experimental results demonstrate that 1,5-NOT, featuring extended conjugation and enhanced planarity, more effectively enhances the hole extraction/transport capabilities and conductivity of NiOx compared to 2,6-NOT. The NiOx/1,5-NOT-based device achieves a remarkable power conversion efficiency (PCE) of 24.20%, along with excellent long-term stability, surpassing the NiOx control device (18.12%) and the 2,6-NOT-based device (21.87%). These findings indicate that modifying NiOx with small organic molecules significantly improves charge transport performance, and increasing molecular planarity is particularly beneficial for enhancing hole transport and reducing defect density, thereby increasing both efficiency and stability. This work provides a new strategy for NiOx modification via small organic molecules, offering a promising route to high-performance inverted PSCs.
Environmental Chemistry•2026•DOI: 10.0000/202604-1
An analytical method was developed for the simultaneous determination of 11 organic ultraviolet absorbents (OUVs) in coral tissues using ultra-high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS). Target analytes included benzophenones (BP, BP-2, BP-3, BP-8) and other common UV filters. Sample pretreatment and chromatographic conditions were systematically optimized. Coral tissue samples were extracted by combined vortexing and ultrasonication, separated on a CAPCELL PAK MG C18 column using a mobile phase of methanol-0.1% formic acid aqueous solution under gradient elution, and determined by multiple reaction monitoring (MRM) with internal standard quantification. Method validation demonstrated good linearity for all target compounds over the range of 0.1–500 μg·L−1 (R2 > 0.990), with method detection limits ranging from 0.020 to 0.133 ng·g−1. The mean recoveries at low, medium, and high spiking levels ranged from 60.5% to 120.3%, with relative standard deviations (RSDs) of 1.6%–10.7%. The method offers advantages of simple pretreatment, good repeatability, and high accuracy, making it suitable for high-throughput determination of OUVs in complex biological matrices such as corals. The method was applied to analyze 89 coral samples collected from Xidao Island, Sanya, and five target OUVs were detected in the samples. This method provides reliable technical support for elucidating the accumulation characteristics of OUVs in corals and assessing their potential ecological risks.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605002
The single-phase partial nitrification and anammox (SPN/A) process has seen limited widespread application due to its slow startup and difficulties in enriching anaerobic ammonium-oxidizing bacteria (AnAOB). This study utilized high-ammonia nitrogen wastewater to initiate and enhance the SPN/A process in a pilot-scale integrated fixed-film activated sludge (IFAS) reactor. By establishing an IFAS-SPN/A coupled system based on the symbiotic relationship between biofilm and sludge, rapid startup and efficient AnAOB enrichment were achieved. An innovative sludge inoculation strategy was employed: first, conventional nitrifying sludge was inoculated to initiate shortcut nitrification and allow ammonia-oxidizing bacteria (AOB) to colonize blank carriers; subsequently, anammox sludge was inoculated to promote efficient AnAOB enrichment on the AOB biofilm. The influent was low-temperature shift condensation water from a synthetic ammonia workshop, with an average ammonium nitrogen concentration of 2300 mg/L and COD ranging from 50 to 200 mg/L. The 180-day experiment comprised three stages: shortcut nitrification startup, SPN/A startup, and load intensification. The system successfully started up SPN/A within 120 days, achieving total nitrogen removal efficiency and removal load of (90.21±2.18)% and (0.31±0.07) kg/(m³·d), respectively, through synergistic biofilm and suspended microorganisms. During load intensification, AnAOB relative abundances in biofilm and flocs reached 18.8% and 35.3%, respectively, and removal load increased to (0.64±0.11) kg/(m³·d). Stable influent quality is a prerequisite for efficient and stable nitrogen removal; a surge in influent ammonium concentration caused nitrite accumulation imbalance and deteriorated performance. Adding an equalization tank before the aeration tank mitigates water quality fluctuations, and a 'dilution-reconstruction' strategy for low-ammonia wastewater facilitates rapid recovery after performance deterioration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3833-1
Developing plasmonic nanomaterials with compositions beyond noble metals is crucial for expanding their applications. Transition metal nitrides, such as titanium nitride (TiN), exhibit excellent plasmonic optical properties and photothermal conversion efficiency, showing promise in catalysis, photothermal therapy, and seawater desalination. However, the structure-property relationship governing their plasmonic optical properties remains unclear. Here, we constructed Au@TiN core-shell nanostructures and systematically investigated the tunability of their geometry, composition, and optical properties. By varying the Au core size and TiN shell thickness, we achieved precise control over the localized surface plasmon resonance (LSPR) from visible to near-infrared wavelengths. Single-particle scattering spectroscopy revealed distinct plasmon hybridization modes, with experimental spectra matching theoretical simulations. The Au@TiN nanostructures exhibited enhanced photothermal conversion efficiency (η = 78.5%) under 808 nm laser irradiation, significantly outperforming pure TiN nanoparticles (η = 45.2%). This work demonstrates multi-factor control over plasmonic effects in TiN, providing insights for designing TiN-based plasmonic nanomaterials for catalysis and sensing.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606005
In the context of carbon peaking and carbon neutrality, urban reclaimed water plants must adopt measures such as energy conservation, consumption reduction, and enhanced resource and energy utilization to achieve carbon neutrality. This study developed a carbon emission balance model and accounting method for such plants, incorporating strategies of carbon emission reduction, carbon substitution, and carbon sink. The optimal pathway towards carbon neutrality was evaluated based on the carbon emission balance ratio. Using a 1×10⁵ m³/d urban reclaimed water plant as a case study, the results showed total carbon emissions of 20,934 t CO2e. The carbon emission reduction from reclaimed water source heat pumps for heating and cooling was 21,701 t CO2e, yielding a carbon emission balance ratio of 103.7%. In contrast, other carbon reduction measures contributed 15,424 t CO2e, with a balance ratio of 73.7%, highlighting the pivotal role of reclaimed water source heat pumps. When the heat pump extracted 27% and 36% of residual thermal energy, coupled with reclaimed water reuse or sludge anaerobic digestion-cogeneration, respectively, both pathways achieved a 100% balance ratio. Assuming year-round extraction, the balance ratio reached 213%. The carbon reduction ratio between utilizing residual thermal energy and chemical energy was 8.76:1. This study demonstrates that urban reclaimed water plants can achieve carbon neutrality through multiple pathways, with residual thermal energy recovery exhibiting significant potential.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3851-3
Aqueous zinc-ion batteries (AZIBs) face critical challenges from zinc anode instability, including corrosion, hydrogen evolution reaction (HER), parasitic byproduct formation, and uncontrolled dendrite growth. To address these issues, we developed a multifunctional cerium-based metal-organic framework (Ce-MOF) coating for zinc anodes. The coating features an ordered porous structure and inherent properties that mitigate HER, suppress side reactions, and inhibit dendrite formation. Symmetric cells using Ce-MOF/Zn demonstrated exceptional cycling stability for over 2060 h at 0.5 mA cm−2 with a low hysteresis polarization of 26 mV. In full cells with an I2@AC cathode, the Ce-MOF/Zn||I2@AC achieved outstanding cycling stability of 28,550 cycles at 5 A g−1, with 91% capacity retention (109.6 mAh g−1). Through integrated characterization employing in-situ optical microscopy, ex-situ XRD, SEM, and DFT calculations, we elucidated the multifunctional mechanism: the Ce-MOF coating facilitates preferential (002)-oriented Zn deposition to suppress dendrites, reduces Zn2+ desolvation energy to enhance deposition kinetics, and modulates interfacial chemistry to mitigate HER and corrosion. This work establishes Ce-MOF coatings as a simple yet powerful strategy for developing high-performance zinc anodes, providing critical insights for advancing practical AZIB technologies.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202505106
Open-pit coal mining causes severe soil nutrient depletion, limiting vegetation restoration. This study, conducted in the Baiyinhua No.2 mining area (Inner Mongolia), evaluated the effects of different fertilization strategies on soil nitrogen (N) and phosphorus (P) availability and microbial community responses. A field experiment was established in May 2023 with five treatments: low (L), medium (M), and high (H) phosphorus inorganic fertilizers, green manure (GM), and a microbial fertilizer (MF) containing nitrogen-fixing and rhizobia bacteria, compared to a control (CK). Results showed that MF significantly increased total carbon (TC) from 8.47 to 10.17 g·kg⁻¹ and total nitrogen (TN) from 0.37 to 0.56 g·kg⁻¹, while H significantly increased available phosphorus (AP) from 9.78 to 26.28 mg·kg⁻¹. Both treatments significantly altered fungal community structure, with increased relative abundances of Gibberella and Alternaria. The study concludes that MF and H improve soil nutrient availability by modulating fungal communities, with MF offering a sustainable biological approach for mine reclamation. These findings provide targeted fertilization strategies for restoring degraded mining soils and advancing green mining practices.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202503016
Open-pit coal mining severely damages soil and plant community structure and function, causing soil nutrient loss and ecological degradation. Vegetation reconstruction is a key measure for restoring degraded mining ecosystems, with the core challenge being the selection of suitable plant species and optimization of plant configurations. This study focused on the degraded ecosystem of the Baiyinhua open-pit mine in Inner Mongolia, screening native plant species for vegetation reconstruction experiments to investigate early-stage changes in soil nutrient availability and the underlying microbial mechanisms. Results showed that soil physicochemical properties and fungal community diversity exhibited strong adaptability during early reconstruction. However, soil fungal community composition and the relative abundance of saprotrophic fungi differed significantly among plant configurations. Leymus chinensis significantly increased the proportion of soil saprotrophic fungi from 67.28% in the control to 81.63%, while reducing the relative proportion of pathogenic fungi from 15.63% to 4.33%, demonstrating its potential to enhance soil health. Medicago rivularis improved soil microbial community composition and increased soil available phosphorus content, highlighting its capacity as an excellent pioneer species for optimizing soil nutrient availability. Furthermore, mixed sowing of grasses and legumes showed potential to enhance the nitrogen-fixing effect of legumes. Given the significant positive correlation between soil fungal community composition and total nitrogen and available nitrogen, the effects of different plant configurations on soil nutrient availability and biological health likely stem largely from the regulation of soil fungal community composition. In conclusion, achieving the goal of selecting optimal plant configurations still requires long-term continuous observation and analysis, particularly for optimizing configurations between high-quality grasses like Leymus chinensis and legumes.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511098
A highly sensitive analytical method for the determination of 2-bromostyrene in tap water and surface water was developed and optimized using headspace solid-phase microextraction (HS-SPME) coupled with gas chromatography-mass spectrometry (GC-MS). The extraction conditions were systematically optimized via single-factor experiments and an L9(34) orthogonal array with range analysis. The optimal conditions were: sample volume 10 mL, extraction time 30 min, extraction temperature 30 °C, stirring rate 1000 r·min−1, and 2.5 g NaCl as salting-out agent. The method exhibited good linearity over the range 100–5000 ng·L−1 (R² = 0.9994), with a detection limit of 13.8 ng·L−1 and a quantification limit of 55.3 ng·L−1. Recoveries from spiked tap water and surface water samples ranged from 90.2% to 102.2%, with relative standard deviations between 5% and 11%. Statistical tests (normal distribution, F-test, t-test) all yielded P > 0.05, confirming the method's reliability. The method is simple, sensitive, and exhibits minimal matrix effects, making it suitable for routine monitoring of trace 2-bromostyrene in drinking water and surface water.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4010-4
Liver fibrosis, a critical pathological consequence of chronic liver injury, remains a therapeutic challenge due to its complex mechanisms and limited effectiveness of conventional treatments. Recent advancements in two-dimensional (2D) nanomaterials, such as graphene derivatives, transition metal dichalcogenides (TMDs), black phosphorus nanosheets (BPNSs), MXenes, and layered double hydroxides (LDHs), have created novel opportunities for antifibrotic therapy. These materials exhibit exceptional physicochemical properties, including ultrahigh surface area, tunable surface chemistry, biocompatibility, and photothermal/electrochemical functionalities, enabling multifaceted interventions in fibrosis progression. The core therapeutic strategies mainly involve modulating hepatic stellate cells (HSCs) activation, inhibiting excessive extracellular matrix (ECM) deposition, and alleviating oxidative stress and inflammatory responses. However, 2D nanomaterials still face great challenges, such as long-term biosafety, precise functionalization for tissue-specific targeting, and scalable synthetic methods. This review systematically summarizes the recent breakthroughs in anti-fibrosis strategies based on 2D nanomaterials, elucidates their potential mechanisms of action, and explores the prospects for clinical translation of these nanoplatforms. Serving as a nexus between materials science and hepatology, 2D nanomaterials offer revolutionary prospects for precision medicine applications in hepatic fibrosis management.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3962-y
Photochromic Förster resonance energy transfer (pc-FRET)-based subnanometric polymersomes with accurate color control offer a transformative yet challenging tactic for advanced and custom-tailored information encryption. Herein, various amphiphilic alternating pyrene/azobenzene-containing copolymers were polymerized using one-pot Ugi four-component polycondensation. Subsequent self-assembly was performed to produce highly-integrated monolayer subnanometric polymersomes (MSNPSs) and their composites, with diameters of around ~250 nm and vesicular thicknesses of approximately ~12.0 Å. J-aggregated monolayer chain-folding mechanism was accountable for the donor-acceptor-donor stacking manner within the vesicular membrane, beneficial to achieve highly efficient energy transfer. The trans-to-cis photoisomerization of azobenzenes rendered MSNPSs and their composites with photo-triggered structural transitions in diameter and vesicular thickness. Benefitting from considerable spectral overlap between cis-azobenzene and pyrene, MSNPSs and their composites were capable of photo-controllable non-invasive pc-FRET performance with a wide Stokes shift (~320 nm). The accurate color variation from blue to red highly depended upon precise modulation of both irradiation duration and precursor-fixed donor/acceptor ratios. The proof-of-concept individually multichromatic 2D QR code was attained using photochromic MSNPSs and their composites in patterning lithography, displaying a multimodal decryption and favorable repeatability for high-level and personalized information protection. Our work paves a prospective avenue to meticulously craft stimuli-chromatic polymersomes for the potential of advanced information encryption.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3949-4
Sodium metal is considered an ideal anode material for high-performance sodium-based batteries. However, volume changes and dendrite growth during cycling seriously restrict its practical application. To address these challenges, this study utilizes harmful green tide algae Enteromorpha prolifera as a raw material to fabricate a self-supporting, sodiophilic, 3D Enteromorpha prolifera-derived carbon (EC) matrix via defect engineering. The results demonstrate that the 3D EC matrix can reduce nucleation overpotential, enhance binding ability with sodium atoms, and induce sodium to deposit horizontally inside EC, effectively addressing the issue of dendrite formation. Furthermore, the Na-EC symmetric cell demonstrates exceptional cycling stability with an ultralow polarization of 12 mV over 1000 h at 5 mA cm−2, 5 mA h cm−2. Notably, this stability persists even under ultrahigh current density and areal capacity conditions (30 mA cm−2, 30 mA h cm−2), maintaining stable operation for 500 h. When configured in full-cell systems with Na3V2(PO4)3 cathode, the assembled cell delivers an initial discharge capacity of 108.1 mA h g−1 at a 1 C rate, and maintains a capacity retention rate of 94.4% after 500 cycles. This study proposes an innovative strategy to advance high-performance dendrite-free sodium metal batteries through the recycling of marine environmental waste into functional energy materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3921-2
Moisture-enabled energy harvesting technologies offer a promising route for self-powered strain sensing, yet conventional generators suffer from slow response, poor recovery, and limited multidirectional resolution. Here, we report a stretchable thermoplastic polyurethane (TPU) nanofiber moisture-enabled electric generator (MEG) with highly aligned ion channels. A carbon black/sodium dodecylbenzene sulfonate (CB/SDBS) layer is coated on the TPU membrane, while carboxymethyl cellulose (CMC) and acidified poly(sodium 4-styrenesulfonate) (HPSS) are applied on opposite sides, establishing lateral hydrophilicity and ion gradients to drive directional ion migration. The planar MEG is lightweight, flexible, and requires no fully covered electrodes, enabling conformity to complex deformations. The aligned channels reduce ion migration tortuosity, enhancing ion transport efficiency and flux. As a result, the aligned MEG (ATMEG) delivers 0.2 V and 0.51 μA cm−2 at ~90% relative humidity, corresponding to 400% and 287% enhancements compared with the unaligned MEG (UATMEG). The ATMEG also exhibits ultrafast response (0.16 s) and recovery (0.08 s). Utilizing its anisotropic characteristics, a multidirectional self-powered strain sensor is developed, capable of distinguishing both the amplitude and direction of human motion, demonstrating strong potential for adaptive wearable electronics and intelligent motion monitoring.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511055
To systematically investigate the spatiotemporal distribution of hydrodynamics and water quality under cascaded hydropower development in the upper Heihe River, a MIKE21-based water environment model was constructed for the mountainous reach. The model simulated the dynamic changes of total phosphorus (TP), total nitrogen (TN), and ammonia nitrogen (NH3-N) from January to August 2023. Calibration and validation against field data showed good performance: the hydrodynamic model achieved a coefficient of determination (R2) of 0.89 and a mean relative error (MRE) of 11.3%; the water quality model achieved an average R2 of 0.86 and an average MRE of 14.21%. Hydrodynamic simulations revealed average flow velocities of 1.78, 0.72, and 0.36 m·s−1 during wet, normal, and dry periods, respectively. Natural river sections exhibited high velocities up to 4.3 m·s−1, while reservoir sections had near-stagnant flow due to hydraulic structures. Water quality simulations indicated that TN and NH3-N concentrations were higher in dry and normal periods, whereas TP was higher in the wet period. Spatially, concentrations in reservoir sections exceeded those in natural sections: natural sections had TP, TN, and NH3-N concentrations of 0.07–0.10, 0.25–0.50, and 0.025–0.250 mg·L−1, respectively, while reservoir sections had 0.12–0.17, 0.60–0.80, and 0.10–0.45 mg·L−1. These findings provide scientific references for water environment management in the Heihe River and similar inland river basins.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60748-7
Cyclohexene is a crucial raw material for nylon production, and the selective hydrogenation of benzene is a key route for its preparation. To promote data sharing and reuse in this field, we collected and standardized experimental data on the hydrogenation of benzene to cyclohexene from publicly available literature, constructing a comprehensive dataset containing catalyst composition, reaction conditions, and reaction results (conversion, selectivity, and yield). This data descriptor details the source, field definitions, generation and processing workflow, quality control, sharing approach, and usage recommendations of the dataset, aiming to provide a reusable data foundation for subsequent statistical analysis, machine learning modeling, experimental design, and catalyst screening. The dataset is provided in Excel format and is accessible via GitHub and ScienceDB. It addresses the lack of unified field definitions, unit systems, and organizational formats in scattered literature data, enabling direct statistical analysis, correlation mining, and predictive modeling. The dataset is expected to accelerate research in optimizing ruthenium-based catalytic systems for selective benzene hydrogenation, which currently suffer from limited cyclohexene yield despite the use of aqueous-phase systems and inorganic salt additives. By offering a quality-controlled, structured dataset, this work supports data-driven approaches to overcome the thermodynamic favorability of complete hydrogenation to cyclohexane and to improve process economics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4123-0
Aqueous aluminum-ion batteries (AAIBs) are promising for large-scale energy storage due to safety, sustainability, and theoretical high capacity. However, sluggish electron/ion transport in conventional cathodes limits rate capability. Here, we first propose high-entropy engineering of metal oxides (HEOs) as cathodes in AAIBs, leveraging the 'cocktail effect' and abundant electron transport pathways to enhance rate-capacity. Atomic-level interactions between different metal atoms broaden the d-band with reduced electronic level degeneracy, facilitating rapid electron transport, achieving one of the best rate capabilities (119.4 mAh g−1 at 10.0 A g−1) among metal-oxide cathodes. The disordered layered oxides formed with a high-entropy framework alleviate electrostatic repulsion between aluminum ions and the fixed lattice, mitigating structural degradation and imparting excellent cycling stability (over 95.1 mAh g−1 after 500 cycles at 2.0 A g−1). The optimized HEO-Cr cathode (Fe0.6Co0.6Ni0.6Mn0.6Cr0.6O4) exhibits outstanding rate performance and cycling stability. DFT simulations and electrochemical tests reveal that multi-transition metal incorporation, bandgap narrowing, and unique lattice structure drastically enhance electron transport efficiency. The layered phase formed after cycling, based on a high-entropy framework, overcomes challenges from high charge density aluminum ions, significantly enhancing cycling stability. This work paves the way for high-performance AAIBs and other aqueous multivalent metal ion batteries by rationally designing high-entropy engineering.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4188-x
Sodium metal anodes, with high theoretical capacity (1166 mAh g−1) and low redox potential (−2.71 V vs. H+/H2), are promising for low-cost, high-energy sodium metal batteries (SMBs). However, uncontrolled dendrite growth and drastic volume changes cause short circuits and safety hazards. This work presents a dual-gradient engineering strategy to address these issues. A 3D self-supporting current collector (SSM-ZnS@Zn) was fabricated by laminating a stainless steel mesh (SSM) with a Zn foil decorated with pre-grown ZnS nanoparticles via a one-step rolling process. The substantial electrical conductivity difference between the bottom zinc foil (~16.6×10^6 S m−1) and the top SSM (~1.3×10^6 S m−1) establishes an electric field gradient. Simultaneously, a sodiophilicity gradient is created by electrochemically in-situ generated sodiophilic NaZn13 and Na2S on the bottom zinc foil, combined with the sodiophobic upper SSM layer. This dual-gradient synergy guides bottom-up sodium deposition, homogenizes current density and electric potential, and reinforces mechanical robustness. The framework exhibits outstanding electrochemical performance in both symmetric and full cells, outperforming most reported 3D structures. A pouch cell assembled with SSM-ZnS@Zn successfully lit an LED lamp, demonstrating practical application potential. This strategy surpasses single-gradient limitations and offers a new approach for high-performance sodium metal anode design.