SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4245-4
The discrimination of volatile organic compounds (VOCs) at trace concentrations remains a critical challenge for environmental monitoring, industrial process control, and non-invasive disease diagnostics. Conventional electronic noses rely on sensor arrays comprising multiple chemically distinct receptors, which introduces fabrication complexity, calibration drift, and cross-sensitivity. Here, we demonstrate that a single-component Ti3C2Tx MXene (TM) sensor array, engineered through controlled surface chemistry and device architecture, generates independent and high-dimensional characteristics (IHC) sufficient for precise VOC pattern recognition. By exploiting the intrinsic heterogeneity of TM basal planes and edge sites, we achieve differential interaction motifs without expanding elemental composition. The array discriminates VOCs including acetone, ethanol, toluene, and hexane at concentrations down to 100 ppb with classification accuracy exceeding 95%. Principal component analysis reveals distinct clustering with cumulative variance of 92.3% captured by the first three principal components. The sensor exhibits a limit of detection of 50 ppb for acetone and response/recovery times of 12 s and 18 s, respectively. Long-term stability tests over 30 days show less than 5% signal degradation. This single-component strategy simplifies fabrication, reduces calibration overhead, and offers a scalable pathway for miniaturized, low-power VOC sensing platforms compatible with Internet of Things (IoT) deployment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4416-8
Copper(I)-based carbene-metal-amide (CMA) emitters offer an earth-abundant alternative to precious-metal phosphors for organic light-emitting diodes (OLEDs), yet efficient green emission remains scarce due to limited π-extension and unbalanced charge-transfer characteristics of N-heterocyclic carbene (NHC) ligands. This work introduces a pyrimidine-fused NHC ligand (CF3PMI) with balanced π-accepting ability, synthesized via a one-pot protocol in good yields. The resulting Cu(I)-CMA complex CF3PMI-BFCF3 exhibits green thermally activated delayed fluorescence (TADF) in doped thin films, with a photoluminescence quantum yield (PLQY) of 90% and a short emission lifetime of 1.16 μs. A vacuum-deposited OLED achieves green electroluminescence centered at 514 nm with an external quantum efficiency (EQE) of 22.7%. Furthermore, a hyperfluorescent OLED employing CF3PMI-BFCF3 as a sensitizer delivers an EQE of 21.8%, green emission at 537 nm, and a narrow full width at half maximum (FWHM) of 30 nm. These results establish a viable molecular design strategy for high-performance green-emitting Cu(I)-based TADF materials and provide a convenient synthetic route for Cu(I)-CMA emitters.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4213-x
Lipid peroxyl radicals (ROO·) are terminal propagating species in lipid peroxidation, driving oxidative damage in neurological disorders. Their prolonged lifetime and rapid diffusion within lipid membranes render them difficult to neutralize. Here, we report a bioelectric-responsive TEMPO-doped polydopamine (PDA@TEMPO) nanozyme that sustains catalytic interception of ROO· radicals under persistent oxidative stress. By coupling a PDA redox reservoir with TEMPO catalytic centers, the nanozyme establishes a self-regenerating radical-neutralization cycle via proton-coupled electron transfer (PCET). The π-conjugated framework facilitates charge migration and enables an electric-field-enhanced antioxidant response. In a seizure model, the nanozyme dynamically responds to bioelectric fluctuations, accelerating radical interception and alleviating oxidative stress in neural microenvironments. These findings establish bioelectric-coupled nanozymes as a general strategy for catalytic and sustained regulation of oxidative stress in neural microenvironments, providing a potential therapeutic approach for neurological disorders.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3648-2
Transient energy storage devices represent an emerging class of biodegradable power systems that provide temporary energy for implantable medical electronics before safely degrading in vivo. From early transient primary batteries to contemporary rechargeable batteries integrated with wireless charging systems, these devices have evolved to enable stable prolonged power supply. Through rational transient design and structural engineering, they achieve desirable electrochemical performance, tunable degradation rates, and mechanical compatibility with soft, irregular, and dynamic biological tissues. This work provides a critical review of state-of-the-art transient energy storage devices, including transient primary batteries, transient secondary batteries, and transient supercapacitors, with emphasis on their electrodes, electrolytes, encapsulation materials, fabrication processes, and applications. We critically analyze material selection strategies, transient design principles, and architecture design for various transient batteries and capacitors. Finally, we discuss existing challenges and outline future directions to guide the clinical translation of biodegradable power solutions for biomedical implants.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3657-9
Perovskite/silicon tandem solar cells (TSCs) have achieved power conversion efficiencies (PCE) up to 34.9%, surpassing the Shockley-Queisser limit of single-junction devices. The interconnection layer (ICL) critically bridges top and bottom subcells, enabling charge carrier recombination. Conventional indium oxide (In2O3)-based TCOs suffer from high-energy ion bombardment during sputtering, damaging amorphous silicon subcells and reducing open-circuit voltage (VOC) and fill factor (FF). Additionally, indium scarcity and cost necessitate indium-free alternatives. Here, we introduce a highly degenerate indium-free samarium-doped cadmium oxide (CdO:Sm) TCO as the ICL for perovskite/SHJ TSCs, deposited via low-damage reactive plasma deposition (RPD). The ultrathin CdO:Sm film (~3 nm) exhibits average transmittance of 85% (400–1200 nm) and 90% (800–1200 nm), enabling efficient near-infrared absorption in the bottom subcell. High doping concentration and mobility ensure excellent electrical conductivity. The low work function (4.04 eV) of CdO:Sm facilitates carrier tunneling and efficient recombination. Devices employing CdO:Sm ICL achieved approximately 1% higher efficiency compared to those with indium-based TCO ICLs. Detailed characterization including contact resistivity (1.68 mΩ cm2), conductive atomic force microscopy, Kelvin probe force microscopy, and photoluminescence quenching confirm enhanced carrier transport and extraction. This work demonstrates a viable indium-free ICL for high-efficiency perovskite/SHJ TSCs, addressing both performance and sustainability challenges.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(25)61036-5
Large graphene oxide (LGO) sheets offer significant advantages over smaller ones in various applications, yet their production via Hummers-type oxidation of large natural graphite flakes remains challenging due to difficulties in achieving full oxidation and avoiding fragmentation. This study provides the first direct evidence that large graphite flakes (up to 1 mm) can be completely oxidized without fragmentation under static conditions, as revealed by in-situ monitoring. The oxidation process is governed by diffusion of the oxidizer between layers, described by Fick's law, where a high oxidizer concentration gradient increases the diffusion rate. By minimizing the amount of concentrated H2SO4 solvent, we achieved a semi-solid state that elevates oxidizer concentration, facilitating Mn(VII) diffusion and enabling complete oxidation of gram-scale large flakes with significantly reduced reagent consumption. Reaction temperature was optimized to balance graphite oxidation and Mn(VII) self-decomposition. Using this approach, 200-, 100-, and 50-mesh natural graphite were fully oxidized with reduced H2SO4 and KMnO4 usage. After exfoliation, LGO with average lateral sizes of 27.3, 58.7, and 116.2 μm were obtained, respectively, with 100% conversion and yield over 165%. This work not only provides a scalable, cost-effective strategy for LGO production but also advances the fundamental understanding of Hummers-type oxidation.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507032
To mitigate global warming, regional carbon neutrality pathways are critical. Based on the Guangdong Energy Policy Simulator (EPS) model, this study simulates total energy consumption and greenhouse gas (GHG) emissions under baseline, Carbon Neutral 60 (CN60), and Carbon Neutral 50 (CN50) scenarios, and analyzes the emission reduction effects and costs of various energy policies. Results show that by 2060, total energy consumption under CN60 and CN50 decreases by 39% and 44% relative to baseline, respectively. Primary electricity and other energy, natural gas, oil, and coal account for 56%, 26%, 14%, and 4% under CN60, and 60%, 24%, 13%, and 3% under CN50. GHG emissions under CN60 drop to 80×10^6 tCO2e by 2060, an 89% reduction from 2020; under CN50, emissions reach 92 and 55×10^6 tCO2e in 2050 and 2060, respectively, reductions of 87% and 92% from 2020. Policies such as increasing clean electricity share, industrial electrification (hydrogen), increasing green power purchases, building electrification, F-gas reduction, and improving industrial energy efficiency standards show significant reduction effects, with clean electricity share being the primary source. Policies like improving industrial energy efficiency standards, increasing industrial product utilization, and increasing clean energy vehicle market penetration are cost-effective; increasing clean electricity share, green power purchases, building electrification, and F-gas reduction effectively balance reduction effects and costs. Industrial electrification (hydrogen) contributes >5% cumulative reduction but faces economic challenges for full-scale promotion in the short term; industrial carbon capture and storage and electrolytic hydrogen contribute <2% cumulative reduction with high costs. Therefore, Guangdong should prioritize cost-effective policies, promote balanced policies, gradually optimize energy structure, achieve clean electricity, and foster green industrial transformation to achieve carbon neutrality at lower economic cost.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0021
Red mud, an industrial solid waste from alumina production, poses severe environmental challenges. This study presents a resource-efficient strategy to convert red mud into high-performance microwave absorbing materials. FexOy/TiO2/C composites were synthesized via a sol-gel method using starch as carbon source, followed by carbothermal reduction. The phase composition and microstructure were optimized by adjusting calcination temperature and raw material ratio. The optimal sample, RmCT-5.4-700, exhibited a minimum reflection loss (RLmin) of -30.2 dB at 14.0 GHz with an effective absorption bandwidth (EAB) of 5.3 GHz at a coating thickness of 2.0 mm. The superior absorption performance is attributed to the synergistic effects of dielectric components (TiO2, graphitized carbon) and magnetic components (Fe3O4/Fe). Carbothermal reduction introduces defects that induce dipole polarization, while the conductive network formed by graphitized carbon and Fe3O4/Fe particles enhances conductive loss. Heterogeneous interfaces between Fe3O4, Fe, TiO2, and the red mud matrix promote interfacial polarization. The magnetic loss of Fe3O4/Fe improves impedance matching, facilitating electromagnetic wave penetration and absorption. This work not only provides a novel route for red mud valorization but also contributes to the high-value utilization of solid wastes.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604009
Biological nitrogen removal in wastewater treatment plants (WWTPs) is often limited by insufficient influent carbon sources, necessitating external carbon addition to enhance denitrification. Conventional single carbon sources, such as sodium acetate, frequently fail to meet the metabolic demands of complex microbial communities, compromising nitrogen removal efficiency and stability. Composite carbon sources, by providing multiple electron donors, can improve metabolic cooperation among microorganisms, yet their underlying microbial mechanisms remain insufficiently understood. In this study, activated sludge from a municipal WWTP was used to investigate the microbial mechanisms of composite carbon sources during denitrification. Batch denitrification experiments were conducted in combination with metagenomic and metatranscriptomic analyses to systematically characterize microbial community structure and functional gene expression under different carbon source conditions. Results showed that, compared with sodium acetate as the single carbon source, the composite carbon source system (sodium acetate: sodium succinate: ethanol = 2:1:3) increased the denitrification rate from (6.822 ± 0.141) mg/(L·h) to (8.370 ± 0.186) mg/(L·h), representing a 22.7% improvement, while reducing N2O accumulation by approximately 55%. Metagenomic analysis revealed that Ottowia, Rubrivivax, Thauera, and Zoogloea were the dominant denitrifying genera. Metatranscriptomic results further demonstrated that the composite carbon sources significantly upregulated the transcription of key denitrification genes, with nirS, norB, and nosZ increasing by 37.8%, 27.4%, and 48.6%, respectively. In addition, the composite carbon sources promoted complementary carbon metabolic strategies among different microbial communities, enhancing electron donor supply and improving denitrification efficiency. These findings indicate that composite carbon sources synergistically enhance denitrification performance through regulation of functional gene transcription in complex microbial communities, providing a theoretical basis for carbon source optimization in WWTPs.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61097-9
Silicon/carbon (Si/C) composites are promising anode materials for high-energy-density lithium-ion batteries (LIBs) because they mitigate the severe volume expansion and poor electrical conductivity of pure silicon anodes. This review systematically summarizes the state-of-the-art preparation methods for Si/C composites, including ball milling, spray drying, electrostatic spinning, and chemical vapor deposition (CVD). Structural engineering strategies, such as carbon precursor coating, silicon-precursor-based wet chemistry, and silicon surface modification, are critically assessed for their effectiveness in enhancing electrical conductivity, buffering volume changes, and improving overall electrochemical performance. The review highlights that while Si offers a theoretical capacity of 4200 mAh g−1, far exceeding graphite's 372 mAh g−1, its practical application is hindered by capacity fading and low initial coulombic efficiency. The integration of carbon matrices not only provides mechanical flexibility but also facilitates electron transport. Key performance metrics from recent studies, including specific capacities exceeding 1000 mAh g−1 and improved cycling stability over hundreds of cycles, are discussed. The review also addresses the challenges of scalable production and cost-effectiveness, emphasizing the need for optimized precursor selection and processing parameters. Future research directions are proposed, focusing on the rational design of hierarchical structures and the development of novel binders to further enhance the long-term durability of Si/C anodes. This comprehensive overview serves as a valuable resource for researchers and engineers aiming to advance the commercialization of high-energy-density LIBs.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61106-7
Hard carbon anodes for sodium-ion batteries suffer from limited capacity, low initial Coulombic efficiency, and poor long-term cycling stability. To address these issues, we report a dual-stabilization strategy that combines micropore confinement and chemical bonding to control sulfur species in coal-derived hard carbon. Bituminous coal, with its naturally condensed aromatic framework, serves as the carbon precursor. A two-step thermal process first constructs a microporous carbon framework, followed by gas-phase sulfidation to introduce sulfur. The sulfur is confined within micropores and forms stable covalent C–S bonds with the carbon matrix, providing synergistic physical–chemical stabilization. This suppresses sulfur migration, prevents interfacial side reactions, and introduces additional redox-active sites. The optimized sample (HC-10) delivers a high reversible capacity of 450 mAh/g after 800 cycles at a current density of 1 A/g, with excellent rate capability and cycling stability. Mechanistic analysis reveals that the stabilized sulfur species reversibly participate in sodium-ion storage and improve interfacial kinetics. This work provides an effective strategy for stabilizing sulfur in coal-derived carbon materials and offers insights into the design of high-performance anodes for sodium-ion batteries.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507081
Coal chemical waste salt, a solid residue from evaporative crystallization of high-salinity wastewater, poses significant environmental risks and challenges for resource utilization due to its complex composition. This study systematically analyzes its composition and environmental hazards, highlighting its typical "mixed salt" nature and the potential threats of organic pollutants and heavy metals to soil, water, and ecosystems. It reviews mainstream treatment pathways, including organic degradation, inorganic impurity removal, and salt separation, with a focus on the resource utilization of sodium chloride and sodium sulfate and their industrial prospects. The current pollution control technical specifications and product quality standards are examined, comparing the scope and technical points of relevant standards such as the "Technical Specification for Pollution Control of Chemical Waste Salt." Finally, countermeasures are proposed to address challenges including difficult treatment of mixed salts, insufficient resource utilization incentives, and incomplete standard systems, emphasizing technological innovation, policy guidance, and standard improvement.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508021
Coal chemical industry waste salt, generated from high-salinity wastewater treatment, poses a bottleneck for green transformation under the 'dual carbon' strategy due to its low value and high complexity. This study investigated a typical coal chemical industrial park in Northwest China, using principal component analysis (PCA) on actual waste salt samples to identify pollutant characteristics and assess resource utilization potential. Results showed total organic carbon (TOC) ranged from 707.9 to 7,737.9 mg·kg⁻¹, with benzo(a)pyrene concentrations frequently exceeding the limits of the 'Identification Standards for Hazardous Wastes' (GB 5085.3). Hardness ions and metal ions also surpassed relevant product standards. PCA classified the waste salts into three types: sodium sulfate type, sodium chloride type, and high-complexity mixed salt, each corresponding to distinct resource utilization pathways. The study proposes differentiated technical routes based on PCA classification, providing a feasible reference for classified management and technology selection. This research supports the national policy of 'harmless pretreatment + resource utilization' for waste salt, contributing to green and high-quality development of the coal chemical industry.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605003
Dark fermentation offers a sustainable route for hydrogen production, yet its yield is often limited by inefficient electron transfer and low microbial metabolic activity. This study engineered a mixed microbial biohybrid system incorporating Fe2O3 nanoparticles to overcome these bottlenecks. At an optimal Fe2O3 concentration of 300 mg/L (S300), the hydrogen yield reached 2.94 mol H2 per mol glucose, equivalent to 73.5% of the theoretical maximum and 1.59 times higher than the control (S0). Mechanistic analyses revealed that Fe2O3 nanoparticles stimulated microbial metabolism, as evidenced by a 4.09-fold increase in ATP content and a 1.30-fold rise in total protein concentration. Hydrogenase and dehydrogenase activities were enhanced by 24.62% and 63.11%, respectively, while electron transfer system activity increased by 3.44-fold, accompanied by a significant reduction in charge transfer resistance. Notably, the gradual release of Fe2+ ions from Fe2O3 reduction by dissimilatory iron-reducing bacteria (DIRB) was identified as a key factor in stimulating enzyme activity and electron transfer. Microbial community analysis showed that the relative abundance of Clostridium, a key hydrogen-producing genus, increased by 9.75 percentage points to 42.60% in S300. This study demonstrates that Fe2O3-based biohybrids offer a promising strategy to enhance dark fermentation hydrogen production, providing both performance improvements and mechanistic insights into nanomaterial-microbe synergies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3835-0
The development of high-performance CO2 separation membranes is critical for advancing carbon capture technologies. Two-dimensional (2D) material membranes, with tunable interlayer nanochannels functionalized by nanomaterials (e.g., metal ions), are promising for CO2 capture. However, achieving uniform nanomaterial distribution without compromising separation performance remains a challenge. Here, we propose a multifunctional molecular immobilization strategy to fabricate a metal ion intercalated graphene oxide (GO) membrane with enhanced CO2 capture performance. The multifunctional molecule sodium p-aminobenzenesulfonate (SPABS) enables in situ and uniform distribution of Na+ in the interlayer channels of the GO membrane. The amino groups of SPABS undergo nucleophilic addition reactions with epoxy groups on GO sheets, resulting in stable interlayer channels. Meanwhile, the hydrophilic sulfonic acid groups enhance water adsorption capacity in the GO interlayer channels, synergizing with Na+ to form active sites that facilitate fast and selective transport of CO2 over N2. The resulting membrane exhibits enhanced CO2 capture performance. A large-sized membrane (15 cm × 20 cm) fabricated by scalable blade-casting shows reproducible performance. This work provides insights and a tool for tailoring nanochannels of 2D material membranes for molecular separation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3792-6
The rapid expansion of home-based digital health monitoring necessitates electrodes capable of simultaneous, accurate acquisition of electrophysiological signals and body temperature. Conventional single-function electrodes, including metal block, gel, and Ag/AgCl types, suffer from limitations such as restricted movement, skin irritation, signal degradation over time, and poor permeability for prolonged use. To overcome these challenges, we developed a low-cost, multifunctional flexible electrode enabling concurrent body temperature and electrophysiological signal monitoring without cross-interference. Body temperature is assessed via visual colorimetric evaluation and precisely measured using a custom smartphone application. The electrode features high air permeability, ultra-thin architecture, superior flexibility, antibacterial properties, and strong skin adhesion, while maintaining low interfacial impedance for stable, long-term acquisition of high-fidelity signals such as electrocardiography (ECG) and surface electromyography (sEMG). Integrated with a Raspberry Pi platform and a hybrid convolutional neural network-long short-term memory (CNN-LSTM) algorithm, the system achieves intelligent arrhythmia detection with 99.30% accuracy. This novel electrode provides a powerful tool for multifunctional sensing of temperature and physiological electrical signals, with significant potential for wearable physiological tracking applications.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60642-1
Inherent minerals significantly influence the thermal conversion of coal, yet the interaction mechanisms among minerals affecting tar generation during pyrolysis remain unclear. This study investigates the effect of acidic mineral components on the behavior of ion-exchangeable Ca2+ during coal pyrolysis. Coal samples were prepared via HCl and HCl-HF acid washing followed by Ca2+ ion exchange. Pyrolysis was conducted in a fixed-bed reactor. Acid washing effectively reduced ash content but also decreased organic element contents (carbon, hydrogen). Loading ion-exchangeable calcium enhanced the thermal weight loss rate in the 500–550 °C range, shifting the peak temperature from 530 °C to 514 °C. At a final pyrolysis temperature of 600 °C with slow heating, kaolinite in acidic minerals underwent dehydroxylation to form metakaolin. The content of small aromatic rings (<6 rings) in char from Ca-loaded coal was lower than that from acid-washed coal without Ca. Coexistence of acidic minerals with ion-exchangeable Ca increased aliphatic hydrocarbon content in tar: YL-HCl-Ca reached 21.98% versus 13.60% for YL-De-Ca. Acidic mineral components inhibit the adverse effect of ion-exchangeable Ca2+ on tar lightening. These findings provide insights into mineral interactions during pyrolysis, aiding in optimizing coal conversion processes for improved tar quality.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025031901
The rapid expansion of the nuclear power industry has increased the demand for effective nuclear wastewater treatment, making the efficient removal of radioactive iodine isotopes (e.g., 131I, 129I) from aqueous environments a critical challenge. Covalent organic frameworks (COFs), a class of crystalline porous materials characterized by high specific surface area, tunable pore structures, and exceptional stability, exhibit significant potential for capturing radioactive iodine from water. This review systematically examines the adsorption mechanisms of iodine by COF materials, including electrostatic interactions, charge transfer, hydrogen bonding, and secondary mechanisms such as metal coordination, ion exchange, and van der Waals forces. The effects of COF pore structures on iodine removal efficacy are discussed with a focus on pore size and functional group modifications. Key research trends and prevailing challenges in the application of COFs for aqueous iodine capture are analyzed, including the need for selective adsorption in complex wastewater matrices and the scalability of COF synthesis. The review concludes with a perspective on future research directions, emphasizing the design of novel COFs with tailored pore chemistry and the development of cost-effective, regenerable adsorbents for practical deployment in nuclear wastewater treatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3917-x
The escalating global challenge of antibiotic contamination demands advanced sensing technologies for environmental monitoring and public health protection. Here, we present a structurally well-defined, intercalation-engineered metal-organic framework (MOF), HSB-W18, which functions as an ultrasensitive and selective fluorescence sensor for fluoroquinolone antibiotics. Single-crystal X-ray diffraction analysis unambiguously determined both the framework architecture and the spatial organization of intercalated 2,5-dihydroxyterephthalate molecules at atomic resolution. Through ultrasound-assisted synthesis, highly stable book-shaped microsheets (HSB-W18-MS) were obtained, maintaining exceptional aqueous dispersibility and luminescence intensity for over one month. These microsheets offer distinct advantages for antibiotic detection: specific recognition of diverse fluoroquinolones via unique fluorescence signatures; highly sensitive ratiometric detection of enoxacin (ENX) with a limit of detection (LOD) of 5.62 nM and rapid response kinetics (<30 s); exceptional selectivity alongside reusability. Systematic mechanistic investigations revealed a synergistic detection process involving multiple photophysical pathways. Furthermore, a smartphone-based portable detection system was successfully implemented, and the practical utility of the sensor was validated by quantifying ENX in complex environmental samples: tap water LOD = 18.32 nM and river water LOD = 29.87 nM. This study contributes to fundamental materials science and environmental monitoring by elucidating discernible structure-property relationships in intercalated MOFs, demonstrating a robust platform for field-deployable antibiotic detection and proposing an innovative design paradigm for environmental optical sensors.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510042
Given China's escalating municipal solid waste (MSW) generation and the limitations of current classification schemes, this study proposes a novel waste classification model centered on mid-end intelligent sorting technology. The approach integrates targeted pretreatment with multimodal visual recognition and robotic grasping to efficiently sort complex household waste, while compact equipment innovations adapt to the low-value characteristics of recyclables. An engineering demonstration case shows that the technology can effectively recover low-value recyclables comprising 15%–30% of mixed MSW. If applied at 5% of a case city's waste transfer stations, approximately 5×10^4 t of recyclables could be sorted annually. Preliminary estimates indicate a 20% return on investment for operators at an 80 t·d−1 scale. The study demonstrates that mid-end intelligent sorting offers a technically feasible and economically sustainable solution to reduce fiscal expenditure on waste classification while improving efficiency.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512045
To optimize the anode structure of Ti/SnO2-based electrodes in electrochemical advanced oxidation processes (EAOPs) and enhance their electrocatalytic activity and stability, Sn-Sb co-doped Ti/SnO2 electrodes were fabricated via a sol-gel method. The degradation performance and mechanism were evaluated using phenol as a model pollutant. Three electrodes were prepared with different Sn/Sb molar ratios: Ti/SnO2 (10:0), Ti/Sb (0:10), and Ti/SnO2-Sb (9:1). Characterization by XRD, SEM, and electrochemical tests revealed that the Sn-Sb co-doped electrode exhibited a dense surface, higher oxygen evolution potential (OEP), larger electrochemically active surface area, and lower charge transfer resistance compared to single-doped counterparts. In constant-current electrolysis experiments (20 mA·cm−2, pH=5, 0.1 mol·L−1 Na2SO4), the co-doped electrode achieved superior phenol and TOC removal efficiencies and higher apparent rate constants, with the lowest specific energy consumption per unit TOC removal. Radical quenching and intermediate analysis indicated that hydroxyl radicals (·OH) were the dominant reactive species. The degradation pathway involved aromatic ring hydroxylation, ring opening, and further mineralization of short-chain carboxylic acids. Sn-Sb co-doping enhanced the generation of ·OH by increasing surface adsorbed oxygen and defect site density. This synergistic doping strategy significantly improved the electrocatalytic activity and service life of Ti/SnO2-based anodes, providing a basis for the rational design of anode materials for EAOPs in treating refractory organic wastewater.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510017
Municipal solid waste (MSW) is a significant source of urban carbon emissions. This study integrates life cycle assessment (LCA) and system dynamics (SD) to construct a multi-subsystem LCA-SD model covering economy, population, waste generation, transportation, treatment, and resource utilization, using Fuzhou City as a case study. The model was validated against historical data and uncertainty analysis. Carbon emissions from MSW transportation, treatment, and resource utilization during 2013–2023 were calculated, and emission trends under seven reduction scenarios for 2024–2035 were predicted. Results show that Fuzhou's MSW treatment evolved through three stages: 'landfill+incineration', 'treatment structure adjustment', and 'incineration+kitchen waste resource utilization', corresponding to emission growth, fluctuation, and reduction periods. In 2023, total net carbon emissions were 1.07×10^6 t CO2-eq, with incineration being the largest contributor (9.93×10^5 t), followed by transportation (2.93×10^4 t), leachate treatment (2.14×10^4 t), and kitchen waste treatment (7.90×10^3 t, negative emission). Scenario analysis indicates that without further measures, carbon neutrality cannot be achieved. Synergistic enhancement of kitchen waste separation and incineration power generation efficiency can significantly boost reduction, potentially achieving carbon neutrality by 2032. The study provides a dynamic accounting and scenario assessment framework for low-carbon transition of urban solid waste systems.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60658-5
Sulfur dioxide emitted from combustion of sulfur-containing aromatic compounds in fuels is a major contributor to atmospheric pollution. Oxidative desulfurization (ODS) has become a crucial complement to hydrodesulfurization (HDS) due to its mild reaction conditions and high efficiency in removing refractory aromatic sulfides. Metal doping is an effective strategy to modulate the electronic structure of catalysts and enhance catalytic performance. In this study, Mn-doped Co-V-O metal oxide (Mn-Co-V-O) was synthesized via a reflux method followed by high-temperature calcination. The structure, morphology, and surface chemical composition were characterized by FT-IR, XRD, SEM, XPS, and UV-vis DRS. The ODS performance toward dibenzothiophene (DBT) was evaluated using molecular oxygen as a green oxidant. Results indicated that Mn doping significantly enhanced the ODS activity compared to undoped Co-V-O. Under optimized conditions (110 °C, 0.03 g catalyst, 150 mL/min O2 flow, 20 mL model oil), a direct DBT removal rate of 81.6% was achieved. When combined with extraction, the desulfurization rate increased to 98.0%. Mechanistic studies revealed that Mn doping increased the surface oxygen vacancy concentration, facilitating oxygen activation to generate superoxide radicals (·O2−). Radical trapping experiments confirmed that ·O2− was the key active species responsible for selective oxidation of DBT to DBTO2. This study provides a reference for designing efficient metal oxide catalysts for deep oxidative desulfurization.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608020
This paper systematically reviews the progress and achievements of China's collaborative innovation pilots for pollution and carbon emission reduction, identifies existing problems, and proposes targeted recommendations. As of the first batch, 64 pilot units (21 cities and 43 industrial parks) have issued implementation plans, with overall smooth progress and notable phased outcomes. Most pilots have actively promoted institutional and mechanism innovations, achieving substantial advancements in key sectors and critical areas, and yielding replicable practices. However, challenges persist, including fragmented interdepartmental collaboration, insufficient alignment of management systems, funding shortages for synergistic projects, and inadequate technological support. Recommendations include intensifying awareness campaigns, establishing coordinated promotion mechanisms, accelerating management system implementation, advancing core technology R&D, conducting progress evaluations, and amplifying publicity. For the second batch, suggestions focus on expansion strategies, pilot types, and selection methods, emphasizing incremental tasks, diverse pilot subjects (from provincial to enterprise levels), and clear articulation of expected outcomes and demonstration targets. The paper underscores the need to transform local experiences into institutionalized frameworks, fostering a four-dimensional synergy of carbon reduction, pollution control, green expansion, and economic growth, thereby contributing to China's ecological civilization and global climate governance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3969-9
Phosphor-in-glass (PiG) materials are promising color converters for high-power laser illumination, yet suppressing interfacial reactions between phosphor and glass matrix at elevated sintering temperatures remains a critical challenge. Here, we report a Y3Al5O12:Ce3+ (YAG:Ce) phosphor-in-silica glass (PiSG) with high SiO2 content (>85 wt%) fabricated via a Cs2CO3 flux. Incorporation of Cs2O significantly inhibits SiO2-YAG:Ce reactions, preserving internal quantum efficiency (IQE) at 97.7% of pure YAG:Ce, and achieving 88.3% IQE even after calcination at 1400°C for 2 h. In contrast, smaller alkali ions (Li+, Na+) accelerate YAG:Ce decomposition. Mechanistic studies reveal that Cs+ with large ionic radius and weak interaction with oxygen suppresses non-bridging oxygen (NBO) formation, promoting a complete silica network that limits alkali ion diffusion. Leveraging the mixed alkali effect (10% Li2O + 5% Cs2O), the PiSG exhibits enhanced hydrothermal stability, withstanding 200°C treatment for 10 h. A PiG film-sapphire device delivers 3080 lm luminous flux and 213 lm W−1 efficiency under blue laser excitation. These findings establish YAG:Ce-PiSG as a highly promising color-conversion material for high-performance laser illumination.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4057-4
The escalating use of ionizing radiation in medical and industrial applications necessitates lead-free, flexible, and sustainable shielding materials. Current development relies on empirical trial-and-error, which is inefficient. This study introduces a machine learning-assisted Monte Carlo simulation strategy for rapid optimization of metal filler compositions for X-ray attenuation across 40–120 kV. Guided by this AI-driven approach, polyvinyl alcohol (PVA)-based gels containing uniformly dispersed Bi/W/Gd2O3 nanoparticles were developed, forming within 1 minute at -20°C using a PVA-DMSO/H2O co-solvent system. The optimized gel with 50 wt% metal loading exhibits exceptional mechanical properties: tensile strength of 1.76 MPa, toughness of 6.3 MJ m−3, and elongation of 600%. It achieves >98% X-ray shielding efficiency at 5 mm thickness, outperforming lead composites at 120 kV. The physically cross-linked network provides recyclability and anti-freezing capability, retaining flexibility at -50°C. This work establishes a data-driven paradigm for designing high-performance radiation-shielding materials, demonstrating AI's potential to accelerate materials discovery and enable scalable fabrication of eco-friendly protective systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4145-0
Conductive fibers face a fundamental trade-off between high electrical conductivity and substantial mechanical stretchability, which critically undermines their reliability under extreme or dynamic mechanical conditions. To overcome this challenge, we report a bio-inspired, hierarchically structured conductive fiber engineered by mimicking the parallel-fibril architecture and integrated matrix of skeletal muscle. This fiber is constructed from multiple parallel spandex yarns as the elastic core, a continuous liquid metal (LM) layer as the conductive pathway, and a composite waterborne polyurethane (WPU)/fluoropolymer (FP) sheath as the protective matrix. This unique architecture concurrently delivers exceptional stretchability (>3500%), high electrical conductivity (3.76 × 10^5 S m−1), and outstanding stability against water and mechanical abrasion. Leveraging its excellent conductivity and mechanical compliance, the fiber can be woven into textiles and function as a receiving coil for efficient wireless power transfer. Additionally, a twisted-pair capacitive strain sensor fabricated from this fiber demonstrates a broad, linear response up to 1000% strain. When integrated into garments, the sensor effectively monitors a wide range of physiological activities, from gross joint movements to subtle biological signals, including wrist pulse, vocal vibration, ballistocardiogram, and respiration. This work presents a conductive fiber that integrates high conductivity, ultra-stretchability, waterproofness, and long-term durability, offering a robust material platform and a scalable fabrication strategy for advancing all-weather health-monitoring systems, smart textiles, and next-generation wearable electronics.