SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4432-9
Sodium vanadium phosphate (Na3V2(PO4)3, NVP) with NASICON structure is a promising cathode for sodium-ion batteries but suffers from low electronic conductivity and a high energy barrier for the V4+/V5+ redox couple, limiting practical energy density. A medium-entropy tuning strategy yields the multi-element substituted Na3.2V1.5Cr0.1Fe0.1Mn0.1Ni0.1Ti0.1(PO4)3 (ME-NVP). Entropy modulation tailors the microscopic electronic structure, enabling reversible V4+/V5+ redox at 4.0 V. Analyses reveal a synergistic diffusion mechanism that accelerates Na+ transport and enhances multiple-electron redox kinetics. Ex-situ X-ray diffraction confirms highly reversible structural evolution during cycling. The ME-NVP cathode delivers 116.8 mAh g-1 at 0.1C and retains 83.9% of initial capacity after 1000 cycles at 20C, with excellent performance from -12 to 50 °C. This work demonstrates that configurational entropy regulation unlocks high-energy polyanion cathodes for advanced sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4463-3
Organic-inorganic hybrid lead halide perovskites exhibit exceptional photovoltaic properties, yet their low crystallization energy promotes defect generation and necessitates precise control over synthesis parameters, hindering scalable fabrication. Ambient large-area coating methods suffer from environmental disturbances, leading to nonuniform crystallization and mixed α/δ phases, resulting in module efficiencies below 20% compared to >27% for lab-scale spin-coated cells. This work introduces a phase-locking strategy using 3-ureidopropyltrimethoxysilane (TMPU) incorporated into the PbI2 precursor solution during two-step blade coating. TMPU undergoes simultaneous cross-linking and interaction with the perovskite intermediate, forming a dynamically evolving intergranular network that blocks moisture and reduces the energy barrier for α-FAPbI3 formation. This approach achieves spatiotemporally homogeneous crystallization, eliminating directional inhomogeneity. Under segmented and monolithic aging protocols, control devices exhibited severe position-dependent degradation with only 34% efficiency retention at early-coated positions after thermal cycling, whereas phase-locked films maintained over 84% of initial photoluminescence intensity across all regions. Encapsulated modules retained over 90% of initial efficiency after 1500 h of 85°C maximum power point tracking (ISOS-L-2) and after 2300 h under 85°C/85% RH damp-heat testing (ISOS-D-3). The TMPU-based strategy combines exceptional performance (21.5% module efficiency) with robust stability, offering a distinct advantage over alternative approaches. This work addresses the kinetic and spatial dimensions of upscaling, demonstrating that morphological uniformity is a fundamental contributor to stability, marking a critical advance toward practical deployment of perovskite photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3722-3
Magnesium alloys are promising biodegradable bone implant materials due to their biocompatibility and mechanical compatibility, but rapid degradation and postoperative bacterial infection limit clinical application. Here, zeolitic imidazolate framework-8 (ZIF-8) and 3,4,9,10-perylenetetracarboxylic diimide (PD) composite coatings (ZIF-8@PD) were fabricated in situ on micro-arc oxidation (MAO) coated AZ31 alloys via two-step and one-step (OS) methods. The MAO/ZIF-8@PD and MAO/ZIF-8@PD (OS) coatings reduced corrosion current density by three and two orders of magnitude, respectively, compared to MAO coating, due to the physical barrier of the 2D-co-3D MOF structure. Under 808 nm near-infrared laser irradiation, photothermal and photodynamic effects from PD, combined with contact killing by released Zn2+ ions, achieved bactericidal rates ≥99.5% against E. coli and S. aureus. Photothermal conversion efficiencies were 44.01% and 48.57% for the two-step and one-step coatings, respectively. The distinct Zn2+ sources led to different 2D-co-3D MOF structures, influencing degradation and antibacterial behavior. These coatings offer a strategy to enhance corrosion resistance and antibacterial activity of Mg alloys for biomedical applications.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010608
This study investigated the occurrence and distribution of 27 per- and polyfluoroalkyl substances (PFAS) in surface water and sediment of the Fuchun River, a tributary of the Qiantang River Basin. Surface water samples were analyzed using ultra-performance liquid chromatography coupled with high-resolution mass spectrometry. Total PFAS concentrations (∑PFAS) in surface water ranged from 30.04 to 105.26 ng/L, with mean and median values of 59.64 ng/L and 51.43 ng/L, respectively. The dominant compounds were perfluorooctanoic acid (PFOA), hexafluoropropylene oxide dimer acid (GenX), and perfluorobutanoic acid (PFBA). Concentrations generally decreased from upstream to downstream, consistent with previous studies. Notably, GenX levels were significantly elevated compared to earlier reports. In sediment, ∑PFAS concentrations ranged from not detected (ND) to 0.59 ng/g dry weight, with mean and median values of 0.14 ng/g and 0.11 ng/g, respectively. PFOA and perfluorooctanesulfonic acid (PFOS) were the primary sediment contaminants. Source apportionment indicated that industrial wastewater discharge and sewage treatment plant effluents were the main sources of PFAS in the river. Risk assessment using risk quotients suggested low ecological risks to aquatic organisms for most detected PFAS. However, the presence of short-chain and novel PFAS warrants further investigation due to potential unknown risks.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012302
Phosphorus (P) loss from paddy fields contributes to eutrophication in Chaohu Lake. This study evaluated the effects of novel fertilizers and P reduction on P loss and rice yield. Seven treatments were established: no P (CK), rice-specific fertilizer (ZYF), slow-release blended fertilizer (SRF), Xinjutian compound fertilizer (XJT), enhanced loss-controlled fertilizer (CRF), CRF with 10% P reduction (CRF-10P%), and CRF with 30% P reduction (CRF-30P%). Results showed that novel fertilizers and P reduction significantly reduced concentrations of total phosphorus (TP), dissolved phosphorus (DP), and particulate phosphorus (PP) in surface water and leachate. The first 5 days after basal fertilization and heavy rainfall were high-risk periods for P loss. Rainfall increased TP concentrations by 417.74%–432.86% and 94.85%–351.35% in surface water and leachate, respectively; DP increased by 120.80%–322.44%, and PP by 280.66%–501.77% and 80.23%–297.55%. Compared with ZYF, SRF, XJT, and CRF reduced TP loss by 15.43%–33.95%, with SRF showing the lowest loss. Under P reduction, CRF-10P% and CRF-30P% reduced TP loss by 31.48% and 37.04%, respectively, with CRF-30P% achieving the lowest loss. Notably, CRF-10P% increased rice yield by 22.37% relative to ZYF, indicating that moderate P reduction with enhanced loss-controlled fertilizer can maintain or increase yield while reducing environmental risk. The study concludes that CRF-10P% offers a promising strategy for sustainable rice production in the Chaohu Lake watershed.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3834-x
Lithium metal anodes face critical barriers to practical application due to dendritic growth and interfacial instability, which cause short cycle life and safety hazards. This work introduces a highly stable and ultrahigh-rate lithium metal anode using a lithiophilic Sm2S3-modified carbonaceous host. The in situ formation of a Li2S-reinforced interphase layer enables highly reversible lithium plating/stripping and uniform deposition. The modified anode achieves an ultrahigh rate capability of 20 mA cm−2 and ultralong cycling stability of 7440 cycles with dendrite-free morphology. In a 4.5 V anode-less Li||LiCoO2 cell with an areal capacity of ~1.93 mA h cm−2, the system sustains over 1100 cycles with 87.2% capacity retention under harsh conditions: an ultralow negative-to-positive capacity ratio (N/P) of ~0.26 and lean electrolyte of ~5 g Ah−1. Furthermore, an anode-less pouch cell with an ultrahigh areal capacity of ~6.01 mA h cm−2 delivers superior cycling performance even at an ultra-low N/P ratio of ~0.71 and ultra-lean electrolyte of ~1 g Ah−1, achieving a high energy density of 505 Wh kg−1. This work provides a scalable and effective strategy for advancing reliable, practical lithium metal batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3833-1
Developing plasmonic nanomaterials with compositions beyond noble metals is crucial for expanding their applications. Transition metal nitrides, such as titanium nitride (TiN), exhibit excellent plasmonic optical properties and photothermal conversion efficiency, showing promise in catalysis, photothermal therapy, and seawater desalination. However, the structure-property relationship governing their plasmonic optical properties remains unclear. Here, we constructed Au@TiN core-shell nanostructures and systematically investigated the tunability of their geometry, composition, and optical properties. By varying the Au core size and TiN shell thickness, we achieved precise control over the localized surface plasmon resonance (LSPR) from visible to near-infrared wavelengths. Single-particle scattering spectroscopy revealed distinct plasmon hybridization modes, with experimental spectra matching theoretical simulations. The Au@TiN nanostructures exhibited enhanced photothermal conversion efficiency (η = 78.5%) under 808 nm laser irradiation, significantly outperforming pure TiN nanoparticles (η = 45.2%). This work demonstrates multi-factor control over plasmonic effects in TiN, providing insights for designing TiN-based plasmonic nanomaterials for catalysis and sensing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3817-3
The rapid development of artificial intelligence (AI) and big data-driven edge intelligence applications has created an urgent demand for highly efficient computing hardware. Ferroelectric memristors have emerged as promising candidates for edge hardware due to their multi-level conductance tunability and high integration potential. In this work, we fabricated yttrium-doped hafnium oxide (YHO) memristors with a remanent polarization of ~30 μC/cm2, a multi-level resistive state retention time of approximately 10^5 s, and an endurance of up to 10^9 cycles. Based on this device, we constructed a real-time path-tracking system for intelligent vehicles—which achieves 100% path recognition accuracy—and a traffic sign denoising network optimized for hardware mapping via a hierarchical mixed-precision quantization strategy; this network yields denoised images with a peak signal-to-noise ratio (PSNR) of 27.04 and a structural similarity index measure (SSIM) of 0.80. This work paves an innovative pathway for the practical application of hafnium-based ferroelectric memristors, accelerating the development of highly efficient hardware for edge intelligence.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509078
The rapid expansion of photovoltaic (PV) installations and the impending retirement of early-stage modules have made the recycling of end-of-life PV modules an urgent issue. This review systematically examines the types and structures of retired PV modules, with a focus on crystalline silicon (c-Si) and thin-film technologies. It critically evaluates the principles, processes, and pros and cons of physical, chemical, pyrolysis, biological, combined, and emerging methods for recovering c-Si modules. The current status of silicon, metal, and valuable component recovery processes is summarized. For thin-film modules, the core technologies for recovering valuable components via pyrometallurgical, hydrometallurgical, biological, and novel approaches are analyzed in depth. Results indicate that conventional methods (physical, chemical, pyrolysis) remain dominant but suffer from high energy consumption, pollution, and chemical usage. Emerging technologies such as biological and green leaching are identified as key research directions, though they face challenges of low technical maturity and high costs. Finally, policy orientations and existing challenges are discussed, and future development directions are proposed, providing significant guidance for the sustainable and large-scale green development of the PV industry.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60636-6
Polyoxymethylene dimethyl ethers (DMMx) are promising clean diesel additives. Compared to the traditional aldol condensation route, the one-step oxidative method for producing DMMx directly from methanol is a green synthesis route offering significant advantages. However, due to the complexity of the reaction, a balance must be struck between oxidation depth and C–O chain growth efficiency. This imposes specific requirements on the design of catalysts with multifunctional active sites: the catalyst should possess appropriate oxidative activity, suitable acid strength distribution, and effective synergy between these two functions. To address these challenges, this study designed a sulfuric acid-modified molybdenum-doped NASICON catalyst, which demonstrated favorable catalytic performance in the one-step oxidative synthesis of DMMx from methanol. Over the NSC-Mo-0.5-30% catalyst, methanol conversion rate of 81.3% and the DMMx selectivity of 58.7% were achieved, along with the formation of heavier molecules, as evidenced by the DMM2–6 selectivity of 11.3%. The NH3-TPD, Py-IR and XPS results indicate that the introduction of molybdenum increases the number of weak Lewis acid sites, while sulfuric acid impregnation not only generates gradient-distributed Brønsted acid sites but also promotes the formation of Mo5+/Mo6+ redox pairs. The cooperation of the two types of active sites significantly enhances catalyst performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3840-3
Tactile sensing for dexterous robotic hands is essential for achieving human-like precision in manipulation. However, current tactile sensors face challenges such as insufficient durability, limited coverage, and poor conformability to curved, jointed surfaces. This study presents a stretchable distributed tactile sensor array designed for dexterous robotic hands. The array comprises 18 sensing units distributed across the hand, incorporating quasi-homogeneous functional layers interconnected by crosslinked interpenetrating networks, and composite electrodes combining high conductivity with stretchability. This design yields a thin, soft, transparent, and stretchable sensor array that integrates seamlessly with a commercial dexterous hand. The sensor array exhibits high interlayer tensile strength, high sensitivity, low hysteresis, and excellent long-term reliability over 10,000 loading cycles. Experimental results demonstrate accurate detection of tactile force across the entire robotic hand during object grasping. Using convolutional neural network algorithms, the sensor array identifies different object types with 90.1% accuracy, with results displayed in real time on a digital twin interface. The proposed sensor array holds significant potential for embodied intelligence and robotics in adaptive grasping, safe manipulation, and remote teleoperation.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509004
Acetone, a widely used solvent in the pharmaceutical industry, poses environmental and economic challenges due to its high volatility and the low concentration of acetone in water-based absorbents, which complicates recovery. This study proposes a composite absorbent comprising 1,4-butanediol (BDO), triethylene glycol, sodium citrate, and water, aiming to enhance acetone absorption capacity and enable cost-effective resource recovery. Response surface methodology optimized the absorbent composition to BDO 35%, triethylene glycol 10%, and sodium citrate 5%, achieving an acetone absorption capacity of 51.97 g·kg−1, which is 2.39 times that of pure water (21.77 g·kg−1). Density functional theory (DFT) calculations and AIM topological analysis revealed that BDO forms stronger hydrogen bonds with acetone, characterized by shorter bond lengths and higher electron density, underpinning its superior molecular recognition and absorption capability. Process simulation of absorption-regeneration cycles demonstrated that, compared to pure water, the composite absorbent reduces absorbent consumption by 36.2% and regeneration energy consumption by 41.15% while achieving effluent acetone concentrations below 100 mg·m−3. This multi-scale investigation, spanning macroscopic experiments, molecular mechanisms, and process simulation, validates the feasibility and advantages of BDO-based composite absorbents for VOC control, providing theoretical and data support for the engineering application of alcohol-based absorbents in efficient organic pollutant separation.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511050
Municipal solid waste (MSW) management in Inner Mongolia has long relied on landfilling, facing land scarcity and leachate management challenges. This study addresses the region's dry, cold climate, high proportion of agricultural and livestock waste, fluctuating moisture content, and weak leachate treatment capacity. An engineering optimization was implemented on an 80 t·d−1 vertical rotary gasification-incineration system featuring a dual-combustion-chamber design (primary chamber for medium-temperature pyrolysis-gasification at 550–650 °C and secondary chamber for high-temperature oxidation above 900 °C), coupled with in-situ leachate recirculation. Field measurements showed improved processing capacity and continuous operation stability. Under the project's leachate yield, in-situ recirculation achieved on-site disposal without significant adverse effects on gasification-incineration conditions, providing buffering against moisture fluctuations. During the monitoring period, major gaseous pollutant emissions remained below current national standards. The results provide engineering references for the co-processing and stable operation of small-scale county-level MSW treatment facilities.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4144-y
Developing efficient strategies for electrically manipulating two-dimensional magnetism at room temperature is a key challenge in contemporary spintronics. In this study, we demonstrate giant electromechanical control over the magnetism of the room-temperature van der Waals ferromagnet Fe3GaTe2 by integrating it with the ferroelectric α-In2Se3. Modest gate voltages lead to an almost complete suppression of the coercive field by 96.5%, corresponding to a remarkable peak modulation sensitivity of ~8.1 mT V−1, which stands out among existing van der Waals magnetoelectric systems. Importantly, this substantial magnetoelectric response is predominantly unaffected by voltage polarity, as both positive and negative gate voltages induce similar magnetic modulation effects. To elucidate the underlying mechanism, we tracked the voltage-induced Raman spectral changes, revealing a peak shift of 1.7 cm−1 that accurately represents an effective in-plane tensile strain of ~1.42% under an equivalent bias, demonstrating polarity independence as well. The synchronized magnetic response and strain variation unequivocally indicate that the induced tensile strain serves as the fundamental physical driver behind the magnetic modulation. Additionally, density functional theory calculations corroborate that the reduction in magnetic anisotropy induced by tensile strain results in a decrease in the coercive field. Our work establishes a novel and efficient approach for achieving voltage control of magnetism at room temperature in van der Waals multiferroic heterostructures, highlighting their significant potential for applications in ultra-low-power magnetic logic and sensing technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4068-2
Eutectic high-entropy alloys (EHEAs) combine multi-principal-element compositions with regular lamellar microstructures, offering exceptional high-temperature stability and mechanical properties. However, conventional casting yields random solidification microstructures and inhomogeneous phase distributions, constraining strength-ductility synergy. This study employs directional solidification (DS) on Al19Fe20Co20Ni41 EHEA to achieve precise microstructural control, constructing a multi-level lamellar architecture with a herringbone-like alternating arrangement. This tailored microstructure refines interlamellar spacing, eliminates detrimental isolated B2 phases, and promotes slip continuity at interfaces, enhancing coordinated dislocation motion and uniform distribution across multiple slip systems. Consequently, the DS EHEA exhibits superior mechanical properties compared to most reported thermomechanically processed and directionally solidified HEAs. Micro-mechanistic analysis reveals that homogenized geometrically necessary dislocation (GND) density, interface-assisted crack deflection, and multi-stage strain-hardening from sequential dislocation activation collectively contribute to outstanding strength-ductility synergy. This work demonstrates that programming solidification paths enables design of unique multi-level lamellar architectures, serving as intrinsic microstructural composites that optimize dislocation management and crack propagation, offering a novel paradigm for developing ultra-robust EHEAs for extreme service environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4074-6
Achieving carbon neutralization relies heavily on green hydrogen and electrochemical carbon-nitrogen cycles. However, the complexity of these systems and the cost of traditional Edisonian trial-and-error methods hinder rapid progress. Artificial intelligence (AI) has emerged as a transformative tool, enabling high-throughput data processing and dynamic adaptation. This review surveys the landscape of AI-driven electrochemistry, bridging the gap from atomic-scale design to industrial-scale implementation. Specifically, we focus on three areas: atomic structure-function decoding, fully automated “self-driving” laboratories, and macro-scale simulations for device durability. Furthermore, we elucidate the critical challenges in integrating AI with materials science. By mapping current trends and future directions, this work aims to unlock the full transformative potential of AI in next-generation energy storage and conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4096-7
Hexagonal boron nitride (h-BN) nanomaterials exhibit exceptional properties but suffer from severe aggregation due to undesirable surface characteristics, limiting their application in polymer nanocomposites. Existing covalent functionalization methods often compromise between time efficiency, energy consumption, and structural integrity. This study presents a rapid, room-temperature catalytic grafting strategy using tris(pentafluorophenyl)borane (B(C6F5)3) to functionalize h-BN nanoflakes bearing edge hydroxyl groups. The reaction between B–OH groups and activated Si–H bonds of hydrosilanes proceeds under mild conditions, preserving the structural integrity of h-BN. Density functional theory (DFT) calculations confirm the catalytic feasibility and elucidate two possible reaction pathways: backside-attack and flank-attack mechanisms. The modified h-BN exhibits significantly improved dispersibility in low-polarity solvents and tunable surface properties. This efficient method offers a versatile platform for h-BN surface engineering, facilitating broader practical applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4163-y
Liquid metals (LMs) are promising catalyst systems due to their unique interfacial properties, yet migration and aggregation of active species cause performance degradation. Here, we report a composition optimization strategy using a Ga-In eutectic liquid metal support to reduce surface energy and achieve homogeneous incorporation of Cu species (GaIn-Cu). Comprehensive characterizations confirm uniform Cu dispersion, which inhibits migration and formation of CuGa2 intermetallic phases during CO2 electroreduction (CO2RR). The GaIn-10-Cu catalyst achieves a maximum CH4 Faradaic efficiency of 73.49% at -0.8 V vs. RHE, significantly higher than Ga-Cu (61.49%). Moreover, GaIn-10-Cu exhibits enhanced stability for CH4 generation over 40 h of continuous operation. In-situ spectroscopic studies reveal that GaIn-10-Cu favors formation and protonation of key *CHO and *OCH3 intermediates, steering selectivity toward CH4. This work demonstrates that tuning LM composition modulates catalytic site performance, offering a strategy for durable and selective LM-based electrocatalysts.