SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4464-9
Topological polarization textures have transitioned from theoretical predictions to experimental observations over two decades, yet their stabilization has remained largely confined to low-dimensional architectures where geometric confinement balances depolarization, strain, and gradient energies. Extending these textures into bulk ferroelectrics and quantitatively linking them to macroscopic electromechanical properties constitutes a persistent challenge. Wu et al. address this by engineering vortex and antivortex domains in bulk rhombohedral 0.7Pb(Mg1/3Nb2/3)O3-0.3PbTiO3 (PMN-30PT) crystals. Phase-field simulations reveal that increasing vortex core density from 6 to 27 μm⁻² enhances the dielectric constant (ε33/ε0) and piezoelectric coefficient (d33) by approximately 3.5-fold and 3.4-fold, respectively, correlating with increased polarization curl. Experimentally, a mechanically assisted direct-current poling (MDCP) strategy elevates vortex core density from 0.01 to 21 μm⁻², boosting d33 from 1380 to 1820 pC·N⁻¹ and ε33/ε0 from 4,630 to 6,230. This mechanically driven approach enables controllable manipulation of topological domain architectures in bulk crystals without nanoscale confinement, offering a scalable route for functional optimization. The work establishes bulk ferroelectrics as a platform for topology-mediated electromechanical design, introducing an additional degree of freedom for enhancing piezoelectric performance in three-dimensional crystals.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4418-7
Glioblastoma (GBM) remains the most lethal primary brain tumor, with the blood-brain barrier (BBB) severely restricting effective treatment options. Immunotherapy has achieved remarkable success in cancers such as lung cancer and melanoma, yet its efficacy in GBM is constrained by the immunosuppressive tumor microenvironment and a paucity of tumor-infiltrating T cells. This study developed a biomimetic nanocomposite for the co-delivery of an immunogenic cell death (ICD) inducer and an indoleamine 2,3-dioxygenase 1 (IDO-1) inhibitor to overcome these challenges. Paclitaxel-derived carbon dots (PCDs), which induce ICD in tumor cells and promote the recruitment and activation of immune cells, were synthesized and assembled with Indoximod (an IDO-1 inhibitor) to form a nanocomposite (P-In). A biomimetic coating was subsequently applied to create M@P-In. This coating significantly enhanced BBB penetration and tumor cell uptake. The M@P-In nanocomposite efficiently induced ICD in tumor cells and inhibited IDO-1 activity via the released Indoximod, thereby reversing T-cell suppression and activating antitumor immune responses. Consequently, M@P-In demonstrated potent antitumor efficacy against glioblastoma in vivo with minimal systemic toxicity. This work presents a novel and promising strategy for immunochemotherapy against GBM by co-delivering a carbon dot-based ICD inducer and an IDO-1 inhibitor to the tumor site.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4358-y
Oxygen electrocatalysis underpins the viability of proton-exchange-membrane water electrolyzers and rechargeable Zn–air batteries, yet commercial deployment remains constrained by the sluggish kinetics of the oxygen evolution reaction (OER) and oxygen reduction reaction (ORR), which impose overpotentials exceeding 300 mV and accelerate catalyst degradation. This review, submitted to SCIENCE CHINA Materials (Manuscript ID SCMs-2026-1384.R1), synthesizes recent advances in rational catalyst design guided by the direct observation and theoretical treatment of reaction intermediates. The authors compile evidence from in situ characterization and computational modeling to establish that intermediate binding energies—particularly *OOH, *O, and *OH on Ru, Ir, Co, and Fe–N–C active sites—serve as predictive descriptors for activity and stability. Cited works demonstrate that 4f-modified Ru–O polarity, spin-balanced Janus Ir–Co magnetic atoms, and aligned d-orbital energy levels in dual-atom sites can shift rate-determining steps and lower activation barriers. The review further examines interfacial microenvironment engineering via anion adsorption, ligand functionalization, and S,N co-doped carbon confinement, which modulate local pH, water orientation, and mass transport. Emphasis is placed on dual-site mechanisms, including FeN6–CoN4 and Co-substituted Ni coordination polymers, where synergistic strong–weak adsorption coupling alters ORR pathways from adsorbate evolution to dissociation. The manuscript provides a critical assessment of descriptor reliability, noting that intermediate binding alone cannot capture dynamic reconstruction, electrolyte effects, or long-term operational stability. By integrating in situ spectroscopy with descriptor-based design, the review offers a framework for translating mechanistic insight into durable, cost-effective oxygen electrocatalysts for industrial electrolysis and metal–air batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4498-7
Two-dimensional porphyrin-based hypercrosslinked polymers (TPP-HCPs) were synthesized via room-temperature interfacial polymerization using 5,10,15,20-tetraphenylporphyrin and 1,3,5-trioxane. The resulting TPP-HCPs exhibited a BET surface area of 548 m2 g-1 and a CO2 uptake of 7.97 wt% at 1 bar and 298 K. CuO/TPP-HCPs nanospheres were fabricated by thermal conversion of Cu(NO3)2·3H2O in DMF at 135 °C, using TPP-HCPs as dynamic templates. This in-situ strategy generated CuO nanoparticles within the conjugated porous matrix, facilitating electron transfer and enhancing CO2 access to catalytic centers. In CO2 electroreduction, the composite achieved a total gas Faradaic efficiency exceeding 90% at ~500 mA cm-2 (-1.4 V vs. RHE), with 40.9% for C2H4, 8.2% for CH4, 31.9% for CO, and 12.3% for H2. The catalyst maintained stability over 24 h in an H-cell. These results demonstrate that 2D conjugated polymer-templated catalysts can sustain high-rate CO2 conversion to value-added products, offering a viable route for industrial CO2 utilization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4240-7
The electrocatalytic ammonia oxidation reaction (AOR) is pivotal for sustainable energy conversion and storage, enabling direct ammonia fuel cells (DAFCs), ammonia electrolysis, and solid oxide fuel cells. This review critically examines recent advances in AOR catalysis, emphasizing active-site regulation, interfacial engineering, and device-oriented catalyst development. For noble-metal catalysts, optimizing adsorption and dehydrogenation of NHx intermediates while mitigating poisoning is essential for sustained activity. Non-noble-metal systems, particularly Ni-based catalysts, require precise control of reconstructed working-state phases such as NiOOH-like species to balance activity and selectivity. Interfacial engineering, including heterointerfaces, defect structures, and doped coordination environments, strongly influences the competition between AOR and oxygen evolution reaction (OER), as well as product branching toward N2 or oxygenated nitrogen species. The review underscores that catalyst optimization now extends beyond bulk composition to the precise regulation of the interfacial reaction microenvironment. Furthermore, practical device operation is governed by membrane/electrolyte compatibility, mass transport, ammonia crossover, thermal management, and long-term durability. Bridging fundamental catalyst studies with deployable ammonia energy technologies requires coordinated optimization from active materials to electrode architectures and full-device systems. This review provides a comprehensive framework for designing next-generation AOR catalysts and accelerating their integration into industrial energy systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4381-5
Bismuth telluride (Bi2Te3)-based alloys remain the benchmark for low-temperature thermoelectric applications, yet their conversion efficiency is limited by the trade-off between electrical and thermal transport. This study introduces a pseudo grain boundary engineering strategy to simultaneously enhance the average figure of merit (ZT) in p-type (Bi,Sb)2Te3 (BST) materials. By incorporating Ag-based compounds, the carrier concentration is optimized via substitution of Ag+ ions, while the introduction of secondary phases at grain boundaries effectively suppresses lattice thermal conductivity. The approach yields a peak ZT of 1.35 at 393 K and an average ZT of 1.25 across 303–483 K, representing a significant improvement over pristine BST. Compared to prior reports, this work achieves superior average ZT while maintaining high electrical conductivity, addressing the longstanding bottleneck of thermal conductivity reduction without compromising carrier mobility. The findings underscore the efficacy of pseudo grain boundary engineering in advancing Bi2Te3-based thermoelectrics for solid-state cooling and power generation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4235-6
Fluorite-structured oxides (HfO2, ZrO2) are promising for resistive random-access memory (RRAM) due to their scalability and tunable properties. However, achieving high resistive switching on/off ratios remains challenging. Here, we report a collaborative strategy combining Hf/Zr ratio optimization and Lu3+ doping to regulate band structure and oxygen vacancy concentration in Hf0.4Zr0.6O2 (LHZO) thin films. The resulting LHZO devices exhibit a resistive switching ratio of 8.4 × 10^4, two orders of magnitude higher than that of ZrO2 (1.2 × 10^3). Electrical characterization and synchrotron radiation photoemission spectroscopy reveal that Lu doping widens the bandgap to 4.95 eV, downshifts the valence band, and introduces defect states, collectively suppressing p-type conductivity and reducing off-state leakage current. Simultaneously, Lu3+ doping enriches oxygen vacancies, stabilizing ohmic conductive filaments in the on-state. This co-optimization of band structure and oxygen vacancies effectively enhances insulating properties in the high-resistance state and ohmic conductivity in the low-resistance state, leading to superior resistive switching performance with robust retention (>10^4 s). Our findings establish a fundamental strategy for tailoring electronic properties of doped HfZrO2 thin films toward high-performance RRAM applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4337-2
Silica aerogels are recognized as leading super-insulating materials due to their ultralow thermal conductivity, yet their intrinsic brittleness and poor processability restrict practical deployment in complex industrial and extreme environments. This study introduces a macro-scale 'stiff–soft' synergistic strategy, combining a macroscopically processable, soft-and-tough framework as the load-bearing component with hard-and-brittle polymethylsilsesquioxane (PMSQ) aerogels as the insulating component. A pressure-driven assembly process enables viscosity-tunable PMSQ gel inks to be controllably infused into various hollow frameworks, including honeycomb panels, wheat straws, and hollow fibers. Guided by a modified Hagen–Poiseuille model, ink viscosity is precisely matched to the geometric parameters of the hollow structures. The resulting composites achieve compressive strength of 2.5 MPa, flexural strength of 6.25 MPa, and tensile strength of 40 MPa, while maintaining excellent thermal insulation. This versatile and scalable approach offers a new design paradigm for mechanically adaptive silica aerogel composites in thermal management applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3771-9
High-entropy carbonitride ultra-high temperature ceramics (HECN-UHTCs) typically require high densification temperatures, leading to grain coarsening and degraded mechanical properties. This study introduces CrSi2 as a sintering additive for (Ti, Zr, Hf, Nb, Ta)(C, N), effectively reducing the densification temperature by 200 °C. During sintering, interdiffusion and cation exchange result in the formation of an orthorhombic (Ti, Zr, Nb)2Cr4Si5 phase within the ceramic matrix. The resulting dual-phase ceramic exhibits a hardness of 24.65 ± 0.23 GPa and a fracture toughness of 6.03 ± 0.48 MPa m1/2, significantly surpassing most reported HECN-UHTCs. Enhanced mechanical properties are attributed to crack deflection, increased localized lattice strain, and Cr grain boundary segregation. This liquid phase-assisted low-temperature sintering strategy offers a promising pathway for densifying other ultra-high temperature ceramics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3538-6
The understanding of anion transporting behaviors under sub-nanoconfined regimes can guide the design of high-performance anion selective membranes (ASMs), yet it is little known. Here, we build membrane channels that combine physical rigidity with chemical affinity to anions simply through bridging graphene oxide nanosheets with charged linkers. We observe that the rigidly confined interaction imposed by channels to anions can reconfigure hydration shells in varying degrees for different anions via compensating for hydration-induced energy barriers and differentiating their rearrangement behaviors. During the configuration evolution, water molecules within hydration shells would rotate and simultaneously change their distance from the ion center. Based on the big discrepancy in configuration evolution, these membranes can realize ultrahigh selectivity of, for example, 125 for Cl−/SO4^2− and surpass the performance upper bound concerning Cl−/SO4^2− separation by other membranes. The knowledge of the configuration change of hydration shells during the dehydration process will be key to designing next-generation ASMs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3625-3
Zirconia (ZrO2)-based fluorite ferroelectric materials are promising for nonvolatile memory and logic devices due to their CMOS compatibility and cost advantages over hafnium oxide (HfO2). However, the metastable nature of the ferroelectric orthorhombic phase (o-phase) hinders practical application. Here, we report the strain-mediated stabilization of the ferroelectric o-phase in ZrO2 thin films grown on niobium-doped strontium titanate (NSTO) substrates with different crystallographic orientations via chemical solution deposition. Systematic structural and ferroelectric characterization, combined with simulation, reveals that substrate orientation controls in-plane tensile strain, selectively promoting epitaxial growth of the o-phase. The ZrO2 film on NSTO(110) exhibits the highest o-phase content, achieving a remanent polarization (2Pr) of 92.64 μC/cm², which remains as high as 88.54 μC/cm² after resistive-capacitive (RC) delay calibration. The device shows endurance of approximately 10^7 cycles with favorable fatigue characteristics. X-ray absorption spectroscopy (XAS) further indicates distortion of Zr-O tetrahedra, providing microscopic insight into the ferroelectricity. This work presents a novel strategy for property tuning of ZrO2 films and supports their application in storage and logic devices.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024102403
The rapid combustion of soot at low temperatures is critical for diesel engine cold-start emission control. This study investigates the effects of water vapor (H2O) and nitrogen oxides (NOx) on electricity-pulse-sparked catalysis (EPSC) for soot combustion over a ceramic filter paper-based potassium-supported antimony-doped tin oxide (K/ATO/CP) monolithic catalyst. Under EPSC with 2000 J pulses, the presence of H2O and NOx adversely affected soot combustion performance, yet average reaction rates remained high at 12.0 μmol·gcat−1·s−1 and 9.53 μmol·gcat−1·s−1, respectively, exceeding conventional thermal catalysis (<8 μmol·gcat−1·s−1). In situ Raman and concentration profiles revealed that electricity pulses promote rapid H2O desorption, effectively alleviating H2O poisoning and restoring catalyst activity. In contrast, NOx adsorption forms stable nitrates (e.g., KNO3) that desorb slower than the soot combustion process, leading to incomplete recovery of activity. These findings highlight the importance of adsorbate desorption kinetics in EPSC and suggest that using weakly basic alkaline-earth metals (e.g., Mg, Ca, Sr) with lower nitrate decomposition temperatures could mitigate NOx poisoning. The results provide guidance for advancing EPSC technology in hybrid vehicle exhaust aftertreatment systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3485-0
Aqueous Zn-ion batteries (AZIBs) are promising for next-generation energy storage due to high safety and low cost, but their practical use is limited by Zn dendrite growth and side reactions. An ideal anode/electrolyte interphase should block water contact while enabling fast Zn2+ transport, yet conventional thick interphases increase ionic resistance and polarization. Here, we report a hydrophobic yet ultrathin (~5 nm) polydimethylsiloxane (PDMS) artificial interphase fabricated via conformal coating. The oxygen-rich PDMS layer selectively coordinates Zn2+ while its superhydrophobicity excludes water, and the ultrathin nature enables rapid Zn2+ conduction, enhancing the Zn2+ transference number by 2.28-fold. This synergistic design suppresses dendrites and mitigates hydrogen evolution. The PDMS-modified anode achieves 99.9% Coulombic efficiency over 3500 cycles, 880-hour symmetrical cell operation at 60% depth of discharge, and 2500-cycle full-cell endurance under lean Zn conditions (N/P ratio 5.7). Proof-of-concept pouch cells sustain 1400 cycles with a 0.01% decay rate. This molecular-scale interphase strategy provides a feasible pathway toward practical AZIB implementation.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025012404
Antibiotics, widely used for disease prevention and growth promotion in livestock, are emerging contaminants with potential risks to human health via the food chain. This review systematically analyzed the sources and residual levels of tetracycline (TCs) and β-lactam antibiotics in raw, pasteurized, commercial, and ultra-high-temperature (UHT) sterilized milk from various countries between 2012 and 2024, based on quantitative detection methods such as LC-MS and HPLC. The highest concentrations of TCs were found in milk from Algeria and Iran, while β-lactam residues were most elevated in Algeria, Bangladesh, and Kenya. The predominant TCs were tetracycline, chlortetracycline, and oxytetracycline; β-lactams were mainly penicillin and amoxicillin. Health risk assessment using hazard quotient (HQ) and hazard index (HI) revealed that all individual HQ values were below 1, indicating no significant non-carcinogenic risk from single antibiotics. However, the HI for multiple antibiotics in raw milk from Algeria exceeded 1, suggesting potential cumulative health risks. Furthermore, some studies reported residue concentrations surpassing maximum residue limits (MRLs), underscoring the need for continuous monitoring and control. This review highlights the global variability in antibiotic contamination and the importance of comprehensive risk assessment to safeguard public health.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225250
Slag foaming is a critical phenomenon in electric arc furnace (EAF) steelmaking, enhancing thermal efficiency, suppressing metal splashing, and stabilizing the refining process. Accurate prediction and control of slag foaming are essential for green and efficient steelmaking. This review systematically examines research progress on slag foaming prediction, clarifying the applicability, advantages, and limitations of different predictive methods to support intelligent control of foamy slags. Following the framework of 'influencing factors-prediction methods-development trends', the study summarizes the coupling effects of multiple variables such as basicity, viscosity, surface tension, suspended particles, gas parameters, and temperature on foam formation and stability. It compares five major prediction approaches: empirical formulas, dimensionless modeling, thermodynamic calculations, computational fluid dynamics (CFD) simulations, and machine learning models, analyzing their core concepts, merits, and constraints. Results indicate that single models often struggle to balance real-time capability and accuracy, particularly under multi-variable coupling and complex operating conditions. Therefore, a hybrid prediction framework combining mechanism-based and data-driven models is proposed, emphasizing physical constraints, multi-scale coupling, and multi-source data fusion. This integrated approach is expected to advance slag foaming prediction from 'computable' to 'controllable and adjustable', offering methodological insights for the development of green and intelligent EAF steelmaking.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509124
To reveal the spatiotemporal evolution and driving mechanisms of water quality in the Hanjiang River Basin, this study utilized monthly water quality monitoring data from 54 sections from January 2021 to April 2024. Methods including single-factor index, comprehensive water quality index (WQI), principal component analysis (PCA), and optimal parameters-based geographical detector (OPGD) were employed. Results indicated significant spatiotemporal differences, with total nitrogen (TN), chemical oxygen demand (COD), and permanganate index (CODMn) as major pollutants, TN being the most critical. Temporally, agricultural non-point source organic pollution dominated in wet season, while comprehensive organic pollution with industrial point source characteristics prevailed in dry season. Spatially, water quality deteriorated along the main stream, with tributary downstream areas showing severe pollution, forming a pattern of 'mountainous areas good, plains poor'. OPGD revealed combined effects of natural conditions and human activities, proposing a 'zonal control and targeted treatment' strategy.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60660-3
Catalytic oxidation is a pivotal technology for the valorization of light hydrocarbons, with oxidative dehydrogenation (ODH) and epoxidation using molecular oxygen attracting significant interest due to high atom economy and environmental friendliness. This review systematically summarizes recent advances in the oxidative dehydrogenation of light alkanes (ethane, propane) and aerobic epoxidation of light olefins (ethylene, propylene). For rational catalyst design, it elaborates on performance regulation strategies for metal oxide catalysts such as MoVNbTeOx mixed oxides, NiO-based, and V-based systems, as well as carbon/boron-based non-metal catalysts in alkane ODH, and silver- and copper-based catalysts in alkene epoxidation. Strategies include regulating the oxidation state of active sites, exploiting strong metal-support interactions, engineering particle size and crystal facets, and promoter modification. At the mechanistic level, combining density functional theory calculations with in situ characterization, the review examines C–H bond activation and alkene desorption pathways in ODH, and oxygen insertion routes and competing side reactions in epoxidation. Special attention is given to the dynamic evolution of electrophilic and nucleophilic oxygen species and their decisive role in selectivity. Persistent challenges include suppressing over-oxidation and overcoming the conversion–selectivity trade-off. Future directions propose precise design of active centers, development of inherently safer processes, and in-depth analysis of complex reaction networks, supporting the green transition of the chemical industry.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025022102
Organophosphate pesticides (OPs), the most extensively used insecticides globally, are ubiquitous in environmental matrices and agricultural products, leading to widespread human exposure. This systematic review evaluates the impact of OP exposure on pregnancy complications and adverse birth outcomes, synthesizing evidence from 58 epidemiological studies published between January 2001 and July 2024. Exposure assessment methods, including biomarkers such as urinary dialkyl phosphates, are critically examined. The review finds significant associations between OP exposure and increased risks of spontaneous abortion, gestational diabetes mellitus, gestational hypertension, preeclampsia, preterm birth, and adverse birth outcomes such as low birth weight and reduced head circumference. Potential mechanisms include paraoxonase 1 (PON1) genotype polymorphisms affecting detoxification capacity, oxidative stress, inflammation, metabolic disruption, and altered placental gene networks. The review highlights inconsistencies across studies due to variability in exposure assessment, timing, and population susceptibility. Future research should prioritize longitudinal designs, repeated biomarker measurements, and consideration of PON1 genetic variants to clarify causal relationships and susceptible windows. This comprehensive synthesis provides critical insights for regulatory policies and clinical interventions aimed at mitigating maternal and child health risks from OP exposure.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025021902
Polyacrylonitrile (PAN) ultrafiltration membranes are widely used in water treatment, yet their anti-fouling performance remains a challenge. In this work, PAN was first reacted with sodium azide via click chemistry to synthesize 1,2,3,4-tetrazolium polyacrylonitrile (PAN-N). Subsequently, PAN-N was reacted with iodoacetamide (IAM), 2-iodoethanol (IH), iodoacetic acid (IA), and chlorosulfonic acid (CSA) to introduce hydrophilic groups, and anti-fouling PAN ultrafiltration membranes were fabricated via phase inversion. The membranes were characterized by Fourier transform infrared spectroscopy, 1H nuclear magnetic resonance, X-ray diffraction, scanning electron microscopy, and contact angle measurements. Results showed that the PAN-N membrane exhibited superior performance to pristine PAN, with water flux increasing from 0.9233 to 1.232 L·(m2·h·kPa)−1 and bovine serum albumin (BSA) rejection from 69.23% to 82.4%. Hydrophilic modification further enhanced performance; the PAN-N-IA membrane achieved the highest water flux of 1.7347 L·(m2·h·kPa)−1 and rejection of 93.57%. Anti-fouling tests revealed that modified membranes followed the order: PAN-N-CSA > PAN-N-IA > PAN-N-IH > PAN-N-IAM > PAN-N > PAN. PAN-N-CSA and PAN-N-IA showed comparable anti-fouling performance, with total fouling indices of 56.1% and 58.47%, reversible fouling indices of 47.17% and 46.97%, and irreversible fouling indices of 8.97% and 11.47%, respectively. This work demonstrates that PAN-N-IA membranes combine high flux, high rejection, and excellent anti-fouling properties, making them promising for water treatment applications.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510081
Electrochemical two-electron oxygen reduction (2e−ORR) for hydrogen peroxide (H2O2) synthesis faces challenges of low cathodic catalytic efficiency and complex catalyst preparation. This study prepared nitrogen-vacancy (Nv) rich carbon nitride via one-step pyrolysis, composited with carbon nanotubes (CNT), and loaded onto graphite felt (GF) to fabricate a non-precious metal gas diffusion electrode Nv-C3N4-CNT/GF. The electrode exhibited a three-dimensional fibrous skeleton with interconnected micro-nano hierarchical pores, facilitating efficient electron transport. Electrochemical impedance spectroscopy revealed a low charge transfer resistance of 13.26 Ω, indicating superior electrocatalytic activity and charge transfer efficiency. Single-factor experiments and response surface methodology (RSM) optimization determined optimal conditions: calcination temperature 300 °C, catalyst mass ratio 3:1, Nv-C3N4-CNT loading 0.1 g, current density 40 mA·cm−2, pH 7, and aeration rate 0.1 L·min−1. Under these conditions, H2O2 accumulation reached 1622.73 mg·L−1 after 90 min, which was 1.3 and 1.5 times higher than g-C3N4-CNT/GF and CNT/GF electrodes, respectively. Stability tests showed that after 6 cycles, H2O2 production remained at 1400.52 mg·L−1, and within 960 min, the maximum production reached 2014.04 mg·L−1 with a highest Faradaic efficiency of 54.86%. These results demonstrate the electrode's potential for cyclic use. This study provides a new approach for developing efficient, low-cost electrodes for electrosynthesis of H2O2, offering a reference for green H2O2 production.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60638-X
The extensive emission of greenhouse gases, primarily CO2 and CH4, has contributed to intensified global warming. Dry reforming of methane (DRM, CH4 + CO2 → 2CO + 2H2) offers a pathway for the synergistic utilization of these two major greenhouse gases, presenting important implications for both environmental protection and energy sustainability. However, the catalysts still face challenges such as carbon deposition and sintering of active metals, which adversely affect the catalytic performance and long-term stability. Oxygen vacancies, which are common lattice defects in metal oxides, have been demonstrated to improve the DRM performance by modulating the surface and interfacial properties of the catalysts. This review systematically summarizes research progresses in DRM over the past decade, outlines the major challenges and emphasizes the critical roles of oxygen vacancies in suppressing carbon deposition and inhibiting metal sintering. Furthermore, the mechanisms through which oxygen vacancies influence DRM reactions are discussed, combined with their formation pathways and regulation strategies. These insights provide essential theoretical foundations for the design and synthesis of highly efficient and stable DRM catalysts.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607011
Anaerobic digestion (AD) is a viable route for energy recovery from food waste (FW), yet it often suffers from process instability due to volatile fatty acids (VFAs) accumulation and subsequent pH drop. This study modified red mud (RM) with hydrochloric acid to produce acid-modified red mud (AMRM), aiming to optimize its alkalinity and physicochemical properties. The efficacy of AMRM as an additive in FW anaerobic digestion was systematically evaluated. Results demonstrated that adding 3% AMRM significantly enhanced the buffering capacity and controlled VFAs accumulation, particularly propionic acid. This was attributed to the developed pore structure of AMRM, whose specific surface area increased by 347% compared to raw RM, facilitating rapid VFAs adsorption. Furthermore, AMRM enriched hematite (Fe2O3), which elevated electron transport system (ETS) activity and coenzyme F420 content, suggesting its role as an electron carrier promoting direct interspecies electron transfer (DIET) between syntrophic bacteria and methanogens. Consequently, the cumulative methane yield reached 633.9 mL/g VS, which was 175.1% and 55.2% higher than the control and raw RM groups, respectively. The VS removal efficiency was 75.1%. This study provides a dual-pathway mechanism—adsorption and electron transfer—for enhancing AD performance, offering a cost-effective and sustainable strategy for FW treatment and RM valorization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3979-3
The escalating prevalence of multidrug-resistant Pseudomonas aeruginosa (P. aeruginosa) infections necessitates novel antibacterial strategies. Here, we engineered lectin B (LecB)-targeted glyco-dots (TFP2F) via self-assembly of a photosensitizer (TFP2) possessing aggregation-induced reactive oxygen species (ROS) generation capability with fucose-modified tetraphenylethene glycoclusters (TPE-Fuc4), enabling P. aeruginosa-targeted antimicrobial photodynamic therapy and wound healing promotion. Three photosensitizers (TFP0–2) featuring an “A-D-A” electronic structure were synthesized, exhibiting broad absorption bands and near-infrared (NIR) fluorescence. Among these, TFP2 demonstrated superior Type-I/II ROS production (including ·OH, ·O2−, and 1O2), achieving potent phototoxicity against P. aeruginosa (MIC80 = 7.5 μM). Self-assembly with TPE-Fuc4 yielded glyco-dots TFP2F that facilitated LecB-mediated bacterial targeting, enhanced bacterial uptake, and significantly reduced the MIC80 to 2.5 μM against drug-resistant P. aeruginosa under light irradiation. In a murine P. aeruginosa-infected wound model, TFP2F treatment combined with light irradiation accelerated wound closure to <20% of the initial area by day 8 (vs. >40% in controls) and eliminated >95% of bacteria by day 2. This work presents a convenient strategy for constructing glyco-dots as a potent functionalized platform for precision, lectin-targeted antimicrobial photodynamic therapy.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511046
To evaluate the carbon footprint differences between the emerging ex-situ remediation facility mode and the conventional on-site remediation mode in China, this study employed the SEFA tool to calculate greenhouse gas (GHG) emissions and energy consumption for four typical remediation scenarios. Results indicate that the carbon emission intensity of solidification/stabilization (S/S) in the remediation facility is 12.00% higher than that of on-site S/S, with unit carbon intensities of 66.74 and 59.59 kgCO2e·m−3, respectively, and total energy consumption 11.90% higher. The soil transport segment in the facility S/S contributes 13% of carbon emissions, being the primary reason for its higher total carbon footprint. Conversely, thermal desorption (TD) in the facility exhibits 11.10% lower carbon emissions than on-site TD, with unit intensities of 269.16 and 302.78 kgCO2e·m−3, and total energy consumption 3.97% lower, mainly due to the utilization of landfill biogas as renewable energy for heat and power generation, while soil transport contributes only 3% of emissions. The reagent segment in S/S and the heat supply segment in TD account for 77%–86% and 70%–72% of total GHG emissions, respectively. The study demonstrates that remediation facilities, leveraging advantages such as landfill biogas, can actively aggregate contaminated soil from surrounding areas for centralized thermal desorption, which is beneficial for regional carbon emission reduction in soil remediation.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3517-3
Liquid crystal display (LCD) technology faces challenges in achieving a wide color gamut due to the limitations of conventional green phosphors, such as their low color purity and complex synthesis processes. This study reports a novel narrow-band green-emitting phosphor, Li4WO5:U6+, which uses uranium as the luminescent center through a ligand-to-metal charge transfer (LMCT) mechanism. Under 450 nm blue excitation, the phosphor exhibits a sharp emission peak at 525 nm with a narrow full width at half maximum (FWHM) of 35 nm, achieving both high color purity and a quantum efficiency of 60%. The weak electron-phonon coupling results in spectral sharpness dominated by zero-phonon lines, while its structural robustness ensures exceptional thermal stability. When combined with a K2SiF6:Mn4+ red phosphor and a blue InGaN light-emitting diode (LED) chip, the fabricated white LED demonstrates an expansive color gamut of 110.2% NTSC, significantly outperforming commercial β-Sialon:Eu2+-based white LED devices (84.4% NTSC). These findings indicate that Li4WO5:U6+ is a highly promising candidate for next-generation wide-color-gamut LCD backlighting, offering superior vividness and stability for advanced display applications.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3549-6
Intramolecular noncovalent conformational locks (NoCLs) have emerged as a potent strategy for engineering high-performance organic/polymeric semiconductors (OPSs) by suppressing non-radiative decay. While the impact of NoCLs on small molecules is well-documented, their influence on the physicochemical properties of conjugated polymers (CPs) remains poorly understood due to the structural complexity, low crystallinity, and poor solubility of CPs. This study addresses that gap by integrating theoretical calculations with advanced experimental techniques—temperature-dependent absorption spectroscopy, cryogenic electron microscopy (cryo-EM), dynamic light scattering (DLS), small-angle neutron scattering (SANS), and freeze-drying transmission electron microscopy (TEM). The results demonstrate that incorporating NoCLs into CP backbones increases chain rigidity, enhances intermolecular interactions, promotes the formation of pre-aggregates with optimal length, and improves charge transport. These findings provide a mechanistic framework for designing high-performance CPs, overcoming the limitations of conventional characterization methods that are restricted to small molecules. The work establishes a correlative link between NoCL-induced conformational locking and macroscopic transport properties, offering a rational design pathway for next-generation organic optoelectronic devices.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3631-1
Anion exchange membrane water electrolysis (AEMWE) offers cost and dynamic-response advantages over proton exchange membrane systems, yet commercial deployment is constrained by the alkaline stability of anion exchange membranes (AEMs) and the sluggish kinetics of non-precious metal catalysts. This work reports a series of poly(terphenyl-diphenylmethane piperidinium) (QPDPMTP) membranes synthesized with varied diphenylmethane (DPM) content. The alkyl chain of DPM induces pronounced microphase separation and elevates free volume fraction, yielding an OH− conductivity of 152 mS cm−1 at 80 °C for QPDPMTP-10. After 1032 h immersion in 6 M NaOH at 80 °C, the membrane retains 90.7% of its initial conductivity. An AEMWE cell integrating QPDPMTP-10 with a non-precious NiFeCo LDH/NiS/NF anode achieves 3.11 A cm−2 at 2 V in 1 M KOH at 80 °C and sustains 1 A cm−2 for 1800 h under gradient KOH concentration. These results establish a viable pathway for durable, low-cost AEMWE systems.