SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4432-9
Sodium vanadium phosphate (Na3V2(PO4)3, NVP) with NASICON structure is a promising cathode for sodium-ion batteries but suffers from low electronic conductivity and a high energy barrier for the V4+/V5+ redox couple, limiting practical energy density. A medium-entropy tuning strategy yields the multi-element substituted Na3.2V1.5Cr0.1Fe0.1Mn0.1Ni0.1Ti0.1(PO4)3 (ME-NVP). Entropy modulation tailors the microscopic electronic structure, enabling reversible V4+/V5+ redox at 4.0 V. Analyses reveal a synergistic diffusion mechanism that accelerates Na+ transport and enhances multiple-electron redox kinetics. Ex-situ X-ray diffraction confirms highly reversible structural evolution during cycling. The ME-NVP cathode delivers 116.8 mAh g-1 at 0.1C and retains 83.9% of initial capacity after 1000 cycles at 20C, with excellent performance from -12 to 50 °C. This work demonstrates that configurational entropy regulation unlocks high-energy polyanion cathodes for advanced sodium-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4237-x
Silicon-based (Si-based) anodes are core candidates for next-generation high-energy solid-state batteries (SSBs) due to their high theoretical capacity (~4200 mAh g−1). However, their practical application is constrained by the 'size effect', which influences mechanical integrity and electrochemical performance. This review systematically examines the failure mechanisms of nano-silicon (nSi) and micro-silicon (mSi) anodes when paired with sulfide and organic-inorganic composite solid-state electrolytes (SSEs). Key functional parameters of these SSEs are discussed, along with strategies to mitigate interfacial impedance and accommodate volume changes. Recent progress in structural and interface modifications is highlighted, including the use of hard-carbon-stabilized Li–Si anodes (achieving stable cycling) and pressure-free operation. The review identifies core challenges, such as achieving intimate solid–solid contact and managing mechanical stress, and outlines future directions for 'size effect' regulation to accelerate commercialization of high-energy Si-based SSBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3588-2
The rapid evolution of aerospace technology necessitates the development of multi-functional composites that combine light weight, mechanical robustness, thermal protection/insulation, and electromagnetic interference (EMI) shielding. C/SiC porous ceramic composites are promising for thermal protection in hypersonic vehicles. Here, we report a facile strategy to fabricate Cf/SiC composite polymer-derived ceramics (PDCs) via re-pyrolysis of high-energy ball-milled polycarbosilane-vinyltriethoxysilane-graphene oxide (PVG) with Cf/SiC(rGO)p blend interleaves. In-situ generated honeycomb-like cellular structures and non-directional channels reduce density and increase porosity. High-quality SiO2 joints, formed from Si-dangling bonds, strengthen interfacial bonding via a brazing effect, while in-situ SiOC nanowires (SiOCnws) create a hierarchically enhanced network, improving fracture toughness and crack resistance. Multi-scale interfacial/dipole polarization enhances EMI shielding. The optimized Cf(0.2)/SiC(rGO) composite exhibits low density (1.49 g cm−3), high fracture toughness (6.32 MPa m1/2), hardness (7.18 GPa), compressive strength (72.67 MPa), and EMI shielding effectiveness of 58.31 dB. It maintains structural stability under butane blowtorch ablation at ~1300 °C for 3600 s. Porous variants show thermal conductivity of 0.211 W m−1 K−1 with 69.74% porosity. These multi-functional composites are promising for thermal protection systems in aerospace applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3432-8
This correction addresses an error in the labeling of author affiliations in the original publication (Sci China Mater, 2025, 68: 1561, DOI: 10.1007/s40843-024-3290-9). The corrected affiliations are as follows: Fuxia Huang, Feng Wang, Ya Liu, and Liejin Guo are affiliated with the International Research Center for Renewable Energy, State Key Laboratory of Multiphase Flow in Power Engineering, Xi'an Jiaotong University, Xi'an 710049, China. Yifei Liu is affiliated with the School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240, China. The correction was made upon the request of the authors and with approval from the respective institutions. The original article focused on crystal defects engineering of BiOI to enhance photocatalytic CO2 reduction to C2 products, a critical area for sustainable fuel synthesis. This correction ensures accurate attribution and institutional recognition, which is essential for research integrity and reproducibility. No changes were made to the scientific content or conclusions of the original study.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3695-8
Sulfur-based lithium-ion batteries, particularly those employing sulfurized poly(acrylonitrile) (SPAN) cathodes and graphite (Gr) anodes, offer high theoretical capacity and low cost but suffer from temperature-dependent capacity decay. This study systematically investigates the electrochemical dynamics and capacity decay mechanism of SPAN||Gr pouch cells cycled at 25–55 °C. Multiscale analyses reveal that capacity fade arises from active lithium loss and increased resistance, both accelerated by higher temperatures. Active lithium loss is primarily attributed to dead lithium formation and thickening of the solid electrolyte interphase (SEI) and cathode electrolyte interphase (CEI), while resistance increase is predominantly due to SEI/CEI thickening. As temperature rises, active lithium loss becomes the dominant decay factor. Leveraging the consistent decay mechanism across temperatures, an accelerated aging model based on the Arrhenius equation is developed: y = 0.9x + a. This model accurately predicts cycling parameters at specific temperatures and reduces testing time by 50% when extrapolating from 55 °C to 25 °C. These insights provide critical guidance for developing long-life sulfur-based batteries for practical energy storage applications.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024122001
Biomass is the only renewable carbon resource with huge reserves and wide sources, and it is green and environmentally friendly. Under the background of 'dual carbon', the clean and efficient utilization of biomass has received increasing attention. Preparation of biochar from biomass is one of the main methods to use biomass efficiently. Biochar surfaces possess porous and aromatic structures, which exhibit good fixation effects on heavy metals in wastewater. However, biochar has shortcomings such as difficulty in recovery and non-reusability. The introduction of iron into biochar can not only enrich surface functional groups, develop pore structure, and increase specific surface area, but also endow magnetic properties, facilitating solid-liquid separation after adsorption. This paper reviews the preparation methods of iron-based magnetic biochar (MBC-Fe), summarizes the effects of different iron sources on its characteristics, and illustrates the adsorption performance and mechanisms of MBC-Fe for typical heavy metals in water. Finally, applications of MBC-Fe in the removal of heavy metal ions from wastewater are concluded, and future utilization potential in other fields is proposed. The review highlights that MBC-Fe exhibits high adsorption capacities, e.g., for Pb(II) and Cd(II), with rapid kinetics and easy separation, making it a promising adsorbent for wastewater treatment.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604018
To address the issues of high air volume and unorganized emissions of waste gas in semi-steel vulcanization production lines, a combined approach of experimental testing and numerical simulation was employed to study the diffusion characteristics of VOCs-containing waste gas and the air volume of the collection system. The structure of the semi-enclosed hood was optimized, and pipe diameters were adjusted to achieve negative pressure balance, enabling efficient waste gas collection. Results showed that toluene concentration distributions from numerical simulation were largely consistent with experimental measurements, with a maximum average error of -3.9%. Existing hood inlet wind speeds ranged from 0.04 to 0.2 m/s, indicating uneven distribution. Under calm wind conditions, toluene diffusion in enclosed and semi-enclosed hoods was similar, with concentrations of 248 mg/m³ and 115 mg/m³, respectively, and deposition observed in trenches. For a single vulcanizer, at a design air volume of 2700 m³/h, the enclosed hood achieved a toluene concentration of 80 mg/m³ versus 63 mg/m³ for the semi-enclosed hood, demonstrating superior capture of hot fumes. Optimizing the semi-enclosed hood with soft curtains and a height of 1200 mm, at a total design air volume of 1.0×10⁵ m³/h, yielded an average hood inlet velocity of 0.35 m/s but still uneven distribution. Adding 900 mm gradual reducers and adjusting branch pipe diameters resulted in total air volume deviations of -0.44% and 0.38% for branches I and II, respectively, with individual hood deviations below 10%. This achieved negative pressure balance, effective collection, and improved workshop hygiene.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3847-5
The convergence of artificial intelligence, Internet of Things, and soft electronics has advanced tactile perception in flexible electronic skins, enabling applications in robotics, healthcare, and human-machine interfaces. However, conventional tactile sensing architectures separate sensing and processing, requiring analog-to-digital converters and data transfer to microcontrollers, which is energy-intensive and introduces latency. In-sensor computing integrates sensing and processing, reducing power consumption and enabling in-situ analog operations such as multiplication-accumulation (MAC) for artificial neural networks. Wang et al. developed a capacitive in-sensor tactile computing system combining a flexible pressure sensor array with electrical switching networks and a fixed capacitor to perform MAC operations in the charge domain. The sensor unit uses an ionic dielectric layer of PVA/H3PO4 prepared via sandpaper-templated molding, sandwiched between Au electrodes on waterborne polyurethane substrates, achieving high sensitivity of 0.36 nF/kPa and excellent stability. A 3×3 kernel of sensors with programmable bias voltages implements averaging and Laplacian filters for noise reduction and edge detection, validated experimentally. The system processes binary and analog tactile stimuli, with output voltage scaling proportionally with pressure. This in-sensor computing approach addresses energy and latency bottlenecks, offering a pathway for real-time, power-constrained e-skin applications in autonomous robotics, prosthetics, and intelligent interfaces.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2026.JFCT.0003
Phosphorus and transition metal-modified ZSM-5 zeolites were prepared via incipient wetness impregnation and characterized by XRD, N2 adsorption-desorption, and pyridine-IR spectroscopy. The effects of modified zeolites on catalytic pyrolysis of n-heptane, 3-methylhexane, and methylcyclohexane were systematically investigated, revealing the structure-activity relationship between acid properties and catalytic performance. Results indicate that phosphorus and transition metal modification can regulate the L/B acid ratio of ZSM-5, which significantly influences product distribution. An excessively high L/B acid ratio promotes hydrogen and coke formation, leading to pore blockage and reduced conversion, whereas an appropriate L/B acid ratio facilitates mild dehydrogenation, enhancing ethylene and propylene yields. Reactant conversion followed the order: n-heptane > 3-methylhexane > methylcyclohexane. Efficient conversion of 3-methylhexane and methylcyclohexane requires catalysts with high L acid amount, strong Brønsted acid amount, optimized L/B acid ratio, as well as high specific surface area and micropore specific surface area. This study provides critical insights for designing high-efficiency alkane pyrolysis catalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3994-9
Electrokinetics, the study of charge transfer and mass transport under electric fields, is fundamental to advancing energy storage and electrocatalysis. Organic-inorganic composite materials synergistically combine the structural stability and conductivity of inorganic phases with the functional diversity of organic components, optimizing electrokinetic properties such as charge transfer, ionic mobility, and catalytic activity. This review systematically examines the intersection of electrokinetic phenomena and organic-inorganic composites, focusing on fundamental principles, design strategies, and performance optimization. Advanced materials including metal-organic frameworks (MOFs), organic-carbon hybrids, and single-atom catalysts are highlighted, with applications spanning batteries, fuel cells, wearable devices, and electrocatalytic systems. Emphasis is placed on advanced in situ and operando characterization techniques that probe electrokinetic processes, revealing the interplay between structure, interface, and transport dynamics. By bridging electrokinetic theory and material design, this work provides a roadmap for developing next-generation materials for sustainable energy technologies. The review consolidates recent progress, identifies remaining challenges, and proposes future directions for leveraging electrokinetic principles to achieve high-efficiency, durable energy systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4158-6
Near-infrared piezochromic materials exhibiting luminescence responses are critical for mechanical sensors and storage devices. Covalent organic frameworks (COFs), as crystalline porous materials, combine structural adaptability with tunable photophysical properties, yet their piezochromic applications remain underexplored. Here, we report a series of donor-acceptor structured two-dimensional COFs (2D COFs) with bright red emission, all showing pronounced red-shifts spanning red to near-infrared regions. Notably, Py-BO-COF exhibits the largest piezochromic shift of 187 nm with a high sensitivity of 44.52 nm GPa−1, significantly surpassing Py-BT-COF, TPE-BO-COF, and most reported COF/MOF systems. Py-BO-COF also demonstrates fully reversible and repeatable emission switching over multiple cycles, maintaining excellent linearity without degradation. In situ spectroscopic analyses and theoretical simulations reveal that variations in piezochromic rates arise from differences in charge-transfer (CT) processes, while the pronounced red-shift in Py-BO-COF is associated with reduced interlayer distance and enhanced coplanarity. This study systematically establishes the structure-property relationship in piezochromic 2D COFs, offering strategic guidance for designing highly sensitive and reversible pressure-responsive materials, thereby advancing smart piezochromic systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3960-0
Dry electrode processing offers a solvent-free and scalable pathway toward high-energy lithium metal batteries (LMBs), yet its practical implementation is constrained by tortuous ion/electron transport and weak mechanical cohesion in ultra-thick electrodes. Here, we construct a carbon-coated NASICON-type Li1.3Al0.3Ti1.7(PO4)3 nanofiber network (LATP@C) that serves as an integrated ionic-electronic scaffold within dry-processed Ni-rich cathodes. The one-dimensional LATP@C fibers form a continuous 3D percolation architecture that couples fast Li+ conduction from the NASICON core with efficient electron transport through the conformal carbon shell. Their rough, oxygen-functionalized surfaces further enhance electrolyte affinity, while the mechanically robust fibrous network bridges NCM811 secondary particles, suppressing crack initiation and preserving structural integrity during cycling. Benefiting from these collective effects, the LATP@C cathode with 100 mg cm−2 loading delivers 203 mA h g−1 at 0.1 C and maintains 96.7% capacity over 35 cycles at 0.2 C. Pouch cells incorporating 60 mg cm−2 LATP@C cathodes retain 80.5% capacity after 50 cycles, highlighting the practical viability of this design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4018-6
The pursuit of advanced wear-resistant materials for cryogenic applications is often hindered by a fundamental trade-off between enhancing strength and damage tolerance. CoCrNi-based medium-entropy alloys (MEAs), while excellent in cryogenic toughness, suffer from this very limitation. Although second-phase reinforcement boosts strength, the strain incompatibility between phases inevitably triggers cracking, which is severely exacerbated at low temperatures. This work introduces a novel microstructural design strategy based on regulated partial recrystallization to overcome this long-standing challenge. By tailoring the thermomechanical processing of a (CoCrNi)90Mo10 MEA, we engineered a unique architecture where a fully recrystallized FCC phase is homogeneously embedded within a continuous skeleton of a hard, non-recrystallized σ phase. The alloy with this optimized microstructure achieved a remarkably low wear rate at 113 K that is less than half of its as-cast and fully recrystallized counterparts. The experimental and modeling results indicate the underlying synergy: the σ skeleton provides robust structural support and distributes stress deeply, while the recrystallized FCC phase, with its high density of grain boundaries and annealing twins, acts as a compliant strain-accommodating medium, effectively suppressing interfacial cracking. This combined 'skeleton effect' and 'recrystallization effect' not only delivers exceptional cryogenic wear resistance but also offers a practical strategy for designing high-performance, crack-resistant dual-phase composites for extreme environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4147-9
Fiber-shaped zinc-air batteries (FZABs) with aqueous electrolytes combine intrinsic safety, high energy density (1086 Wh kg−1), and environmental compatibility, making them attractive for wearable applications. However, free water in the electrolyte induces severe anode degradation while being a critical reactant for cathode redox, presenting a dilemma between anode stability and cathode functionality. The semi-open structure of FZABs allows airborne water to permeate and migrate to the anode, causing interfacial instability, while high surface area accelerates solvent evaporation, leading to increased internal resistance and salt crystallization. Consequently, typical cycle life is limited to <50 h. To overcome these challenges, we report a polymer electrolyte that captures atmospheric water as a solvent through the semi-open structure, achieved by introducing acetamide (AA), identified via unsupervised clustering algorithms, into the poly(vinylidene fluoride-hexafluoropropylene)/zinc trifluoromethanesulfonate (PVDF-HFP/Zn(OTf)2) system. AA incorporation preserves solvent-retention capability while reconstructing the Zn2+ coordination structure, promoting salt dissociation and polymer-segment mobility. Low adsorption energy of AA on zinc surfaces suppresses parasitic reactions from ambient moisture, and preferential adsorption across zinc crystal planes directs Zn2+ deposition along the (002) face, leading to uniform plating morphology. The exogenous aqueous polymer electrolyte exhibits superior mechanical properties, enabling stable output even after compression by a 1.7-t vehicle. As proof-of-concept, FZABs integrated with fiber solar cells and sensors in clothing enabled real-time health monitoring and sustainable energy utilization, demonstrating promising practical applications.