SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4428-0
Passive radiative thermal management is reframed as a device-level engineering problem for thermoelectric generators (TEGs) rather than a spectral-material optimization exercise. The surface temperature difference (ΔT) generated by photothermal (PT) absorbers and passive daytime radiative cooling (PDRC) emitters is not equivalent to the effective junction ΔT that drives carrier transport under load; parasitic heat leakage, contact thermal/electrical resistance at electrodes and interfaces, and nonuniform heat spreading systematically degrade the usable gradient. Spectral selectivity sets the upper bound of attainable ΔT, while module architecture, interfacial resistance, and heat-transfer path matching determine whether that bound is preserved as continuous electrical output. The Perspective identifies a critical metrology gap: most reports cite surface ΔT or peak open-circuit voltage without reporting the ΔT-transfer ratio under load, obscuring where thermal losses occur. Because both open-circuit voltage and internal electrical resistance vary with ΔT, external load must be dynamically matched across day-night and weather cycles; night-time reversal of heat-flow direction through the PDRC/PT stack necessitates DC polarity-conversion circuitry, and compact energy storage must buffer intermittent output. The authors argue that fill-factor reduction can preserve junction ΔT by raising thermal resistance but simultaneously increases electrical resistance and suppresses current. Credible assessment criteria are proposed: outdoor 24 h energy density, load-matched power, day-night continuity, and cycle-to-cycle repeatability, rather than peak voltage alone. Near-term deployment targets building-envelope sensors, structural-health monitors, wearables, and distributed IoT nodes where wiring or battery replacement dominates lifetime cost.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4351-8
Breaking intrinsic structural symmetry is a fundamental prerequisite for pronounced nonlinear optical responses. Low-symmetry semiconductors with inherent anisotropy enable self-powered optoelectronic conversion and polarization-sensitive functionalities. This work reports the synthesis of low-dimensional van der Waals chain TeSe2 crystals with intrinsic inversion and C3 symmetry breaking. Angle-resolved polarized Raman spectroscopy and second-harmonic generation measurements confirm crystalline anisotropy and nonlinear optical performance. Electrical transport studies reveal p-type conduction with a room-temperature field-effect mobility of 122 cm2 V-1 s-1. The TeSe2 photodetector achieves self-powered detection and linearly polarized light detection across 405–1064 nm, with a photoresponsivity of 77.3 mA/W at 532 nm. The linear photogalvanic effect response is effectively modulated by gate voltage. Density functional theory calculations attribute p-type doping to Te and Se vacancies, while the nonlinear optical origin is linked to strong Berry curvature. Applications in polarization encoding communication and polarization imaging are demonstrated, indicating potential for low-energy-consuming, highly sensitive, on-chip integrated linear polarized photodetectors.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4177-3
Chirality profoundly influences tumor therapy by regulating key physiological processes, yet the link between chirality and therapeutic properties of atomically precise metal nanoclusters (NCs) remains poorly understood. Atomically precise Au25 NCs protected by chiral cysteine ligands (L-Au25(cys)18, D-Au25(cys)18, and Rac-Au25(cys)18) were constructed and systematically investigated to elucidate the association between chirality and tumor therapeutic performance. Although no significant difference in enzyme-like activity was observed among the three NCs, Rac-Au25(cys)18 exhibited enhanced reactive oxygen species generation under 808 nm laser irradiation, achieving superior phototherapeutic effects in both in vitro and in vivo tumor models. The chiral Au25 NCs induced distinct cell death pathways: L-Au25(cys)18 primarily triggered ferroptosis, D-Au25(cys)18 induced both ferroptosis and apoptosis, and all three NCs activated disulfidptosis. In vivo, tumor inhibition rates for L-Au25, D-Au25, and Rac-Au25 groups were 46.7%, 42.5%, and 68.3%, respectively, with no significant body weight fluctuations and minimal hepatorenal toxicity. Hematological and histopathological analyses confirmed favorable systemic biocompatibility. This work clarifies the correlation between chiral structures and tumor therapeutic performance of gold NCs, providing experimental insights and theoretical support for the design of novel chiral nanomaterials and optimization of precise tumor phototherapeutic strategies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4487-1
Direct seawater electrolysis offers a cost-effective route to clean hydrogen, but the competitive chlorine evolution reaction (CER) and electrode corrosion impede practical deployment. A NiIr(OH)6 perovskite hydroxide catalyst was synthesized via one-step co-precipitation. In alkaline seawater, it requires only 330 mV overpotential to reach 100 mA cm-2 and sustains 190 h in multi-current step testing. In situ Raman spectroscopy shows that Ir species promote the formation of active NiOOH phases, accelerating oxygen evolution reaction (OER) kinetics. Density functional theory calculations reveal that Ir doping modulates the electronic structure of Ni and Ir sites, strengthening OH adsorption (-2.09 eV) and suppressing Cl- adsorption (-1.38 eV), thereby enhancing OER selectivity. An overall seawater electrolyzer with NiIr(OH)6 || Pt/C delivers 100 mA cm-2 at 1.63 V and operates stably for over 100 h. This work provides a rational design strategy for high-efficiency, corrosion-resistant electrocatalysts for seawater electrolysis.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4138-5
Electrocoagulation (EC) has emerged as a promising electrochemical technology for wastewater treatment, offering distinct advantages over conventional chemical coagulation and membrane processes. This review systematically summarizes recent advancements in EC, focusing on the underlying mechanisms, key operating parameters, and diverse technical applications. The EC process involves three stages: electrolytic oxidation and in-situ coagulant formation, destabilization of contaminants, and floc formation. Unlike chemical coagulation, EC requires no external chemical additives, and process control is achieved by adjusting current density, voltage, or electrode materials, enabling adaptation to varying wastewater qualities. The review highlights the influence of dissolved organic matter (DOM) on EC efficiency, as clarified by Luo et al. (Water Research, 2025). Furthermore, it discusses reactor design innovations, including continuous-flow and cascade-type configurations, and the role of current waveforms in mitigating electrode passivation. The integration of EC with membrane bioreactors and forward osmosis is also examined, demonstrating enhanced treatment performance and fouling mitigation. Key challenges, such as energy consumption and electrode scaling, are addressed, along with future research directions. This comprehensive analysis provides a critical framework for optimizing EC systems and scaling them for industrial wastewater treatment, emphasizing the need for holistic reactor design and process integration to achieve sustainable water reuse.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4206-6
Precise patterning of highly ordered organic semiconductor (OSC) thin-film arrays is critical for next-generation electronics. We report a ladder-like polysilsesquioxane (LPSQ) strategy to synthesize two functional analogs with tunable surface energies and robust dielectric properties. These LPSQ dielectrics, functionalized with alkyl or fluoroalkyl side chains, serve dual roles as gate insulators and patterning layers to guide blade-coating of 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT). This approach yields highly aligned arrays suitable for three-dimensional integration in flexible electronics. Synergistic combination of dense LPSQ dielectric packing and aligned semiconductor domains leads to excellent organic thin-film transistor (OTFT) performance, achieving approximately four-fold improvement in field-effect mobility compared to conventional silicon oxide dielectrics. Patterned LPSQ dielectrics enable high-resolution C8-BTBT patterning on plastic substrates, supporting 4-inch-scale 3D integration of flexible logic circuits, including inverters (voltage gain >100), NOR gates, and NAND gates. This work provides a scalable route to high-performance, large-area flexible organic circuits.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605002
The single-phase partial nitrification and anammox (SPN/A) process has seen limited widespread application due to its slow startup and difficulties in enriching anaerobic ammonium-oxidizing bacteria (AnAOB). This study utilized high-ammonia nitrogen wastewater to initiate and enhance the SPN/A process in a pilot-scale integrated fixed-film activated sludge (IFAS) reactor. By establishing an IFAS-SPN/A coupled system based on the symbiotic relationship between biofilm and sludge, rapid startup and efficient AnAOB enrichment were achieved. An innovative sludge inoculation strategy was employed: first, conventional nitrifying sludge was inoculated to initiate shortcut nitrification and allow ammonia-oxidizing bacteria (AOB) to colonize blank carriers; subsequently, anammox sludge was inoculated to promote efficient AnAOB enrichment on the AOB biofilm. The influent was low-temperature shift condensation water from a synthetic ammonia workshop, with an average ammonium nitrogen concentration of 2300 mg/L and COD ranging from 50 to 200 mg/L. The 180-day experiment comprised three stages: shortcut nitrification startup, SPN/A startup, and load intensification. The system successfully started up SPN/A within 120 days, achieving total nitrogen removal efficiency and removal load of (90.21±2.18)% and (0.31±0.07) kg/(m³·d), respectively, through synergistic biofilm and suspended microorganisms. During load intensification, AnAOB relative abundances in biofilm and flocs reached 18.8% and 35.3%, respectively, and removal load increased to (0.64±0.11) kg/(m³·d). Stable influent quality is a prerequisite for efficient and stable nitrogen removal; a surge in influent ammonium concentration caused nitrite accumulation imbalance and deteriorated performance. Adding an equalization tank before the aeration tank mitigates water quality fluctuations, and a 'dilution-reconstruction' strategy for low-ammonia wastewater facilitates rapid recovery after performance deterioration.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605010
The underwater light environment is a critical limiting factor for the colonization of submerged macrophytes and the ecological restoration of shallow lakes. Previous studies rarely quantified the contribution of aquatic environmental factors to the water quality–underwater light–macrophyte relationship, nor did they comprehensively consider factor correlations or establish thresholds for macrophyte colonization. This study, conducted in a typical national wetland nature reserve (Hongze Lake), measured photosynthetically active radiation, light attenuation coefficient (Kd), euphotic depth (Zeu), water transparency (SD), total suspended solids (TSS), chlorophyll-a (Chl-a), total nitrogen (TN), and total phosphorus (TP). A simulation model for Kd was developed, spatial distributions of environmental factors were analyzed, and contribution rates to light attenuation were quantified. Results showed that the mean Kd was 10.31±3.76 m⁻¹, and the mean Zeu (0.53±0.24 m) was lower than the mean water depth (0.94±0.29 m), with a spatial pattern of shallower Zeu in the west and deeper in the east. TSS and Chl-a were the primary direct influencing factors, while TN acted mainly indirectly. To achieve effective macrophyte colonization under average water depth conditions, thresholds were determined: Zeu ≥ 0.94 m, SD ≥ 0.41 m, Kd ≤ 4.95 m⁻¹, and Chl-a ≤ 3.8 μg/L. These findings provide quantitative guidance for lake restoration and water quality management.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605009
Reservoir CO2 emissions are a critical component of the global carbon cycle, yet existing prediction models often neglect reservoir size stratification, mixing data from large, medium, and small reservoirs. This study addresses this gap by constructing a training dataset exclusively for large and medium reservoirs in China and developing a neural network-based CO2 flux prediction model. The model revealed significant latitudinal zonation, with CO2 fluxes in southern low-latitude basins (e.g., Yangtze, Pearl) substantially higher than in northern high-latitude basins (e.g., Yellow, Songliao). Statistical analysis identified total phosphorus (TP) content as the strongest driver, exhibiting a positive exponential correlation with CO2 flux (p < 0.01). Reservoir age and latitude showed significant negative correlations, while physical parameters such as reservoir area, pre-impoundment submersion ratio, and average water depth showed no significant national-scale correlation. The study underscores the heterogeneity of dominant drivers across basins and proposes differentiated carbon mitigation strategies: for southern high-emission basins, controlling phosphorus inputs through wastewater treatment and restricting aquaculture; for northern basins, enhancing soil conservation to reduce carbon-rich sediment influx; and for new reservoirs, implementing vegetation clearance before impoundment and optimizing flood discharge schedules. These findings provide a theoretical basis for carbon emission characterization and support low-carbon management of large and medium reservoirs in China.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605015
The national greenhouse gas voluntary emission reduction trading market was relaunched in 2023, with China Certified Emission Reduction (CCER) as the trading unit, serving as a crucial supplement to the national carbon market. The initial phase includes the offshore wind power sector. This study evaluates the CO2 and air pollutant emission reduction effectiveness and economic feasibility of China's offshore wind power industry under the CCER mechanism. Using CCER methodology, baseline scenario analysis, and empirical data from 2020 and projections for 2025, we quantify reductions in CO2 and principal air pollutants (particulate matter, sulfur dioxide, nitrogen oxides) across coastal provinces. Emission inventories are constructed using authoritative grid emission factors. Economic viability is assessed by integrating levelized cost of electricity (LCOE), additional revenues from CCER transactions, and external environmental benefits. Results provide four policy insights: (1) The sector shows a positive trend in emission reduction and economic-environmental contribution, but faces financial deficit risk by 2025 without CCER subsidies; (2) Economically developed coastal provinces exhibit greater development potential; (3) Profitability analysis for 2020 and 2025 indicates sustainable economic returns with appropriate policy support; (4) Among air pollutants, nitrogen oxides reduction is largest, while sulfur dioxide reduction yields the most significant co-benefits. This study offers evidence-based recommendations for strategic planning and policy formulation in China's offshore wind industry.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3851-3
Aqueous zinc-ion batteries (AZIBs) face critical challenges from zinc anode instability, including corrosion, hydrogen evolution reaction (HER), parasitic byproduct formation, and uncontrolled dendrite growth. To address these issues, we developed a multifunctional cerium-based metal-organic framework (Ce-MOF) coating for zinc anodes. The coating features an ordered porous structure and inherent properties that mitigate HER, suppress side reactions, and inhibit dendrite formation. Symmetric cells using Ce-MOF/Zn demonstrated exceptional cycling stability for over 2060 h at 0.5 mA cm−2 with a low hysteresis polarization of 26 mV. In full cells with an I2@AC cathode, the Ce-MOF/Zn||I2@AC achieved outstanding cycling stability of 28,550 cycles at 5 A g−1, with 91% capacity retention (109.6 mAh g−1). Through integrated characterization employing in-situ optical microscopy, ex-situ XRD, SEM, and DFT calculations, we elucidated the multifunctional mechanism: the Ce-MOF coating facilitates preferential (002)-oriented Zn deposition to suppress dendrites, reduces Zn2+ desolvation energy to enhance deposition kinetics, and modulates interfacial chemistry to mitigate HER and corrosion. This work establishes Ce-MOF coatings as a simple yet powerful strategy for developing high-performance zinc anodes, providing critical insights for advancing practical AZIB technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3982-6
Skin wounds are refractory due to antibiotic-resistant bacterial infection. Although photodynamic therapy (PDT) offers noninvasiveness, high efficiency, and no drug resistance, its therapeutic effect is constrained by the complex structure of wound tissue and diffuse drug distribution. The proinflammatory cytokine tumor necrosis factor-like weak inducer of apoptosis (TWEAK) regulates tissue repair by engaging its receptor Fn14, which is highly expressed in wounds. In this study, we developed a novel photosensitizer, the selenoviologen-TWEAK conjugate (SeV-Tp), to enhance selective enrichment and synergistically promote wound healing. In vitro analyses demonstrated that SeV-Tp, under visible light, generated high levels of reactive oxygen species, resulting in potent antibacterial activity against both Gram-positive and Gram-negative bacteria. Notably, SeV-Tp selectively bound to Fn14 and amplified fibroblast activation via photodynamic cooperation. In a mouse model of antibiotic-resistant Pseudomonas aeruginosa-infected wound, SeV-Tp accelerated healing by reducing bacterial burden, modulating the immune microenvironment, promoting collagen deposition, and stimulating hair follicle regeneration. Moreover, SeV-Tp preferentially accumulated within wound tissues with minimal adverse effects. SeV-Tp represents a strategy that selectively enriches and harnesses synergistic benefits from both components, positioning SeV-Tp as a promising photosensitizer for the treatment of refractory wounds.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60670-6
Direct conversion of syngas to higher alcohols (C2+ alcohols) is critical for coal-based resource utilization and energy security. Here, a series of Na-modified CoFe/Al2O3 catalysts were synthesized via incipient wetness impregnation and evaluated for syngas-to-alcohol reactions. Multiple characterizations (XRD, N2 adsorption-desorption, H2-TPR, XPS, DRIFTS, in situ Raman, Mössbauer spectroscopy) elucidated synergistic effects of Na and Fe promoters. Na facilitated formation of Co-Fe alloy sites during reaction, while Fe modified electronic state of Co and promoted transformation of lattice oxygen to adsorbed oxygen, increasing surface oxygen vacancies. Synergistic interaction between alloy and carbide sites enhanced CO insertion into olefin intermediates, improving C2+ alcohol selectivity. Under 260 °C and 2 MPa, Co1Fe1Na1 catalyst (n(Co):n(Fe):n(Na)=1:1:1) achieved total alcohol selectivity of 45%, with C2+ alcohols comprising 94.1% of total alcohols. This study provides insights into rational design of Co-based catalysts for efficient syngas conversion to C2+ alcohols.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4099-2
Lithium (Li)-metal batteries (LMBs) are promising next-generation energy storage systems due to their high theoretical capacity (3860 mAh g−1) and low electrochemical potential (−3.04 V vs. standard hydrogen electrode). However, uncontrollable Li dendrite growth and volume fluctuations during cycling cause low Coulombic efficiency, safety hazards, and rapid capacity decay. Conventional 3D current collectors mitigate these issues by increasing surface area and providing void space, but they suffer from top-heavy deposition and underutilization of internal space. Emerging Janus/gradient anode structures, featuring asymmetric or gradient properties in lithiophilicity, conductivity, or porosity, enable bottom-up Li plating and efficient space utilization. This review systematically summarizes design principles, operational mechanisms, and recent progress in lithiophilic-lithiophobic Janus designs, conductivity-gradient frameworks, and dual-gradient configurations. These structures collectively improve Coulombic efficiency, cyclic longevity, and safety. The review concludes with future research directions, underscoring the potential of Janus/gradient anodes for high-energy-density and durable LMBs.