SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4500-8
Electroreduction of CO2 to ethylene offers a promising route for renewable electricity storage, yet achieving high ethylene selectivity at industrial current densities remains challenging due to the large energy barrier for C–C coupling. Here, we report a “MOF-assisted in situ doping” strategy to introduce the oxophilic nonmetal phosphorus (P) into the copper oxide (CuO) lattice, constructing a localized Cu–P dual-site adsorption configuration for the key *OCCHO intermediate. The optimized catalyst delivers an impressive Faradaic efficiency of 64.6% for ethylene with a partial current density of 646 mA cm-2. Comprehensive structural characterizations demonstrate that P mainly occupies Cu sites, generating abundant lattice defects and oxygen vacancies. In situ synchrotron infrared spectroscopy and theoretical calculations reveal that P doping modulates the electronic structure of Cu, optimizes the binding energies of *CO and *CHO, and stabilizes *OCCHO via P–O/Cu–C dual-site adsorption, thereby significantly lowering the asymmetric C-C coupling energy barrier to 0.74 eV. This work highlights a dual-site microenvironment regulation strategy for CO2-to-ethylene electroreduction.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4494-9
Superionic conductors exhibit high cation mobility arising from weak binding and continuous transport pathways, atomistically characterized by extensive structural disorder and partial occupancy akin to amorphization. This disorder, whether confined to a cation sublattice or extended to full amorphization, strongly impedes lattice thermal transport, rendering these materials intrinsically ideal thermal insulators. This work investigates Ag26I18W4O16, a superionic conductor tunable from fully amorphous to single-crystalline states, as a model system to probe the impact of disorder and amorphization on thermal transport. Extensive Ag+ disorder, in both crystalline and amorphous phases, reduces thermal conductivity to approximately the theoretical lower bound of 0.16 W/m-K with virtually no temperature dependence, while concurrently achieving the lowest mean sound velocity ever recorded for a dense solid. Pair distribution function (PDF) analysis of synchrotron X-ray total scattering data indicates that short-range disorder (< 5 Å), rather than long-range periodicity, governs thermal insulation performance in both phases. These findings suggest a design strategy reconciling structural stability with glass-like thermal insulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4205-8
The global energy crisis and environmental pollution necessitate efficient recovery and utilization of thermal energy resources such as industrial waste heat. Thermoelectric materials, enabling direct conversion between thermal and electrical energy, offer broad application prospects in waste heat power generation and chip cooling. The energy conversion efficiency is determined by the dimensionless figure of merit, ZT = (S^2σ/κ)T, where S is the Seebeck coefficient, σ is the electrical conductivity, κ is the thermal conductivity, and T is the absolute temperature. Ideal thermoelectric materials require both a high power factor (PF = S^2σ) and low thermal conductivity. However, the strong coupling between electrical and thermal transport parameters makes synergistic optimization challenging. Over the past two decades, strategies such as band engineering, nanostructuring, liquid-like ions, interstitial atoms, phonon softening, and defect engineering have been explored. Among these, entropy engineering has emerged as a novel strategy that achieves synergistic optimization by introducing multiple components to increase configurational entropy. High entropy materials, originating from alloys, are defined as multi-principal element systems with five or more elements in near-equiatomic ratios forming single-phase solid solutions. The molar configurational entropy ΔS_conf = R∑x_i ln x_i, with materials classified as high entropy (ΔS_conf > 1.5R), medium entropy (1R < ΔS_conf < 1.5R), or low entropy (ΔS_conf < 1R). Four core effects are summarized: high entropy effect, lattice distortion effect, sluggish diffusion effect, and cocktail effect. Research has expanded from alloys to oxides, chalcogenides, and half-Heusler compounds. This review systematically summarizes the mechanisms by which lattice distortion in high entropy materials affects electrical and thermal transport, and discusses optimization strategies for thermoelectric performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4237-x
Silicon-based (Si-based) anodes are core candidates for next-generation high-energy solid-state batteries (SSBs) due to their high theoretical capacity (~4200 mAh g−1). However, their practical application is constrained by the 'size effect', which influences mechanical integrity and electrochemical performance. This review systematically examines the failure mechanisms of nano-silicon (nSi) and micro-silicon (mSi) anodes when paired with sulfide and organic-inorganic composite solid-state electrolytes (SSEs). Key functional parameters of these SSEs are discussed, along with strategies to mitigate interfacial impedance and accommodate volume changes. Recent progress in structural and interface modifications is highlighted, including the use of hard-carbon-stabilized Li–Si anodes (achieving stable cycling) and pressure-free operation. The review identifies core challenges, such as achieving intimate solid–solid contact and managing mechanical stress, and outlines future directions for 'size effect' regulation to accelerate commercialization of high-energy Si-based SSBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4217-y
Rational design and construction of effective photocatalysts is a promising way for green and sustainable chemistry, but still a great challenge. Herein, taking triphenylamine-containing aldehydes as reactants, two covalent triazine frameworks (CTFs), tris(4-formylphenyl)amine (TPA)-CTF and tris(4-formylbiphenyl)amine (TBPA)-CTF, were rationally constructed. The strong electron donor property of the triphenylamine moieties derived from the initial reactants and the strong electron acceptor nature of the in-situ formed built-in triazine rings in CTFs endowed these robust triphenylamine-based CTFs with donor-acceptor (D-A) or donor-π-acceptor (D-π-A) structure features. Photocatalytic experiments revealed that, compared with the controlled phenyl analogue CTF, 1,3,5-tri(p-formylphenyl)benzene (TFPB)-CTF, both of the triphenylamine-based CTFs exhibited superior photocatalytic activity not only in photocatalytic hydrogen peroxide generation, but also in photocatalytic aerobic oxidations of diverse organic substrates. Theoretical studies further confirmed that their enhanced photocatalytic performance should be attributed to their unique D-A or D-π-A features in the constructed triphenylamine-based CTFs. This work successfully demonstrated that rational selection of reactants containing electron donor moieties to construct CTFs should be a reliable way for the construction of effective photocatalysts for photocatalytic oxidation reactions.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3848-7
Conventional heterogeneous photocatalysts often suffer from insufficient light absorption, rapid charge recombination, and a lack of specific reactive sites for efficient photocatalytic oxidation. To overcome these limitations, we propose a molecular polarization engineering approach utilizing structurally well-defined donor (D)-acceptor (A) covalent triazine frameworks (CTFs). The construction of dipole-induced built-in electric fields within the D-A-structured CTFs enables enhanced exciton dissociation and facilitates directional charge transfer. Specifically, the asymmetric A1-D-A2 moiety enhances molecular polarization in the dual-acceptor system CTF-TBT (A1-D-A2), enabling efficient charge separation through multiple electron-withdrawing units. This structural design promotes directional electron transfer toward the secondary acceptor (benzothiazole, A2), while simultaneously concentrating holes on the donor unit. Consequently, the A2 moiety acts as a site for efficient O2 activation via electron accumulation, whereas the highly oxidized donor unit provides strongly positive holes (h+) that facilitate substrate oxidation. Experimental and DFT calculation results confirm that CTF-TBT demonstrates highly enhanced photocatalytic oxidation performance, which can be attributed to its multi-channel charge separation mechanism and spatially separated redox-active sites. This study highlights the effectiveness of molecular dipole engineering in designing heterogeneous photocatalysts with controlled charge transfer pathways and improved redox capabilities. The proposed design principles provide a universal approach for promoting solar-driven chemical synthesis applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3623-y
Organic light-emitting diodes (OLEDs) are an advanced technology for full-color displays, yet the low efficiency of blue OLEDs remains a critical bottleneck. Here, we report a new strategy to design robust Pt(II) emitters with enhanced molecular rigidity and increased locally excited character. The resulting Pt(II) emitter exhibits an extremely narrow emission spectrum peaking at 458.6 nm with a full-width at half-maximum (FWHM) of 16.0 nm and a small Huang-Rhys factor of 0.278, together with a high photoluminescence quantum efficiency of 95%. When doped into an OLED, the device emits at 464 nm with high color purity (FWHM = 19 nm) and achieves high external quantum efficiencies (EQEs) of 32.6%, 29.4%, and 26.9% at luminances of 123, 1000, and 5000 cd/m2, respectively. Notably, the device attains a record-high maximum brightness of 84,895 cd/m2 among reported deep-blue OLEDs with Commission Internationale de l'Éclairage (CIE) y-coordinate < 0.15. This work demonstrates one of the highest-performing deep-blue OLEDs reported to date, addressing the dual challenges of efficiency and brightness in this spectral region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3712-2
Electrochemical potential and ion diffusion of electrode materials restrain the energy and power densities of lithium-ion batteries, and these challenges also remain in the intercalation-type Li3VO4 (LVO). In this work, the local [VO4] coordination symmetry in LVO is broken by a higher concentration of oxygen vacancies (Vö), resulting in an increased average V–O bond length and a larger ligand field splitting. These alterations reduce the energy level of the lowest unoccupied orbitals (e*) and lift the electrochemical potential, resulting in a higher voltage output. Additionally, the broken local symmetry in Vö-LVO is found to reduce the band gap and expand the ion transport channels, which favors enhancing electronic conductivity and facilitates ion diffusion, thereby improving the electrochemical kinetics in the energy storage process. The local symmetry broken sample (Vö-LVO) achieves a significantly improved capacity of 532 mAh/g at 0.1 A/g in comparison with 394 mAh/g of pristine LVO, and long cycling stability with retained capacity of 398 mAh/g at 1 A/g over 500 cycles compared with 236 mAh/g of the pristine LVO. The fundamental understanding paves the way to exploit high-performance electrodes via ligand field engineering for next-generation rechargeable batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3652-2
Existing robotic end-effector gripping technologies often encounter challenges such as poor adaptability to environmental changes, incomplete deformation sensing, and insufficient adhesion stability, which can compromise operational safety and reliability. Here, we present the bio-inspired self-sensing suction cup, in which the core self-sensing capability is achieved by combining high-performance, laser-induced graphene/Ag NWs flexible sensors with a Wheatstone bridge design. The flexible sensors provide high sensitivity, while the Wheatstone bridge circuit enables accurate and stable detection of deformation during the gripping process. Integrated into the octopus-inspired suction cup, this system allows for real-time monitoring of deformation and adsorption stability. The self-sensing suction cup demonstrates good performance across a 0–25 kPa negative pressure range, with outstanding linearity (R2 = 0.993) and high sensitivity (GF = 10.436 kPa−1). Experimental results confirm that the suction cup can achieve stable adsorption under varying loads and enable real-time monitoring of the suction cup status during the gripping process. This design provides a promising solution for intelligent gripping systems, logistics, and object recognition in challenging environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3764-5
Rechargeable lithium-ion batteries (LIBs) are ubiquitous in portable electronics and electric vehicles, yet their flammable liquid electrolytes pose safety hazards and limit energy density. All-solid-state batteries (ASSBs) with solid-state electrolytes (SSEs) offer enhanced safety and higher energy density. Among SSEs, metal chloride SSEs (Li aMCl b, M = In, Y, Er) combine high ionic conductivity, mechanical deformability, and compatibility with high-voltage cathodes. However, their ionic conductivity and anode stability require improvement. Here, we introduce pentavalent Ta5+ doping into Li3InCl6 (LIC) to engineer Li+ vacancies via charge compensation, yielding Li3−2xIn1−xTaxCl6 (LITxC, 0 ≤ x ≤ 0.6). Ta5+ incorporation efficiently increases Li+ vacancy content without disrupting the cubic close packing (ccp) structure. The optimized composition, Li2.4In0.7Ta0.3Cl6 (LIT0.3C), achieves an ionic conductivity of 2.19 mS cm−1 at 30 °C and a low activation energy of 0.273 eV, balancing vacancy concentration and Li+ content. Ta5+ doping also enhances kinetic stability against the anode. ASSBs with LIT0.3C demonstrate excellent cycling stability: Ni90 cathodes retain 72.3% capacity after 1000 cycles at 0.5 C, while NCM523 cathodes retain 84.1% after 500 cycles at 0.2 C and 80.7% after 1000 cycles. These results highlight a practical strategy for improving chloride SSE performance, offering new insights for high-performance ASSB design.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61071-2
Aqueous zinc-ion capacitors (ZICs) are promising energy storage systems due to their high specific capacity and superior reliability. Heteroatom-doped carbon materials have been shown to substantially increase the capacitance of ZICs, yet the underlying mechanisms remain poorly understood. In this work, coal-based activated carbon was functionalized with both boron (B) and nitrogen (N) to serve as the cathode material in ZICs. The optimized material, designated CAC-120, exhibits a high specific capacity of 371.4 mAh g−1 at 1 A g−1 and retains 74% of its initial capacity after 10,000 cycles. Electrochemical analysis and density functional theory (DFT) calculations reveal that pyridinic N plays a crucial role in enhancing Zn2+ storage, demonstrating superior electrochemical reversibility. Furthermore, an assembled aqueous ZIC using the CAC-120 cathode achieves a high reversible capacity of 90.8 mAh g−1 at 0.2 A g−1 and exceptional long-term stability over 17,000 cycles. This work provides valuable insight into the design of high-capacity and ultrafast pseudocapacitive carbon cathodes for ZICs, highlighting the synergistic effects of pore structure engineering and heteroatom doping.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3727-0
Lead halide perovskites are promising scintillators for X-ray imaging due to high X-ray absorption efficiency, excellent luminescence, and facile synthesis. However, their ionic nature challenges simultaneous high photoluminescence efficiency and environmental robustness. This work introduces a multilevel encapsulation strategy: CsPbBr3 quantum dots (QDs) are sequentially coated with Cs4PbBr6, SiO2, and polydimethylsiloxane (PDMS). Cs4PbBr6 passivates surface defects, while SiO2 and PDMS provide barriers against moisture, heat, and radiation. The resulting CsPbBr3@Cs4PbBr6/SiO2/PDMS flexible films exhibit a photoluminescence quantum yield (PLQY) of 85%, outstanding mechanical flexibility, and durability under stretching, bending, and compressing. Films retain emission stability under elevated temperatures, prolonged X-ray irradiation, and extended water immersion. X-ray imaging demonstrates spatial resolution of 12 lp/mm, enabling distortion-free imaging of curved objects; superior water resistance allows long-term underwater imaging. This work highlights hierarchical encapsulation in balancing luminescence efficiency and stability, offering a pathway toward practical flexible perovskite scintillators.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3693-0
The development of catalysts with highly efficient oxygen evolution performance and low-Ir loading is key to scaling up the application of proton exchange membrane (PEM) water electrolysis technology. Here, an Ir-skin catalyst (Ir@KM) is realized on a potassium-manganese oxide (K0.25MnOx (KM)) using an ion-exchange method. The Ir-skin over the prepared Ir@KM has a low Ir–Ir atomic distance, endowing an energetically favorable oxide path mechanism to allow a low theoretical overpotential of 0.13 V. Ir@KM offers a low overpotential of ~280 mV at a current density of 10 mA cm−2 and provides a high mass activity of up to 18,500 A gIr−1 at a cell voltage of 1.8 V in PEM, which is 17.6 times higher than that of IrO2, demonstrating a significant advantage in reducing the cost of the membrane electrode. The presented Ir-skin concept represents a promising strategy to fabricate low-Ir catalyst with high activity and durability for practical applications of PEM.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3716-x
Flexible pressure sensors (FPSs) are pivotal for fall detection and rehabilitation training, yet conventional synthetic-based sensors suffer from resource-intensive manufacturing, high costs, and environmental pollution. This study introduces a sustainable fabrication strategy for FPSs using natural materials. Electrodes were fabricated by treating natural wood strips with a flame retardant, converting them into high-quality graphene via cost-effective infrared laser processing, and transferring onto starch-based substrates. The dielectric layer comprised an electrospun composite nanofiber membrane of cyclodextrin and carbon nanotubes. The resultant capacitive FPS exhibited high sensitivity (2.15 kPa⁻¹ within 0–10 kPa), a low detection limit (~6.5 Pa), rapid response and recovery times (29 ms and 39 ms), and excellent long-term stability exceeding 5000 cycles. Biocompatibility was outstanding (cell viability >98%), and the sensor fully degraded within 6 hours. Integrated with wireless technology, the sensor enabled a fall detection and rehabilitation monitoring system. Data processing utilized a Tiny Machine Learning module on a mobile platform, transmitting data to a cloud-based system. The system accurately identified five common fall postures and assisted clinicians in guiding rehabilitation exercises, achieving recognition accuracies of 99% and 100%, respectively. This work offers a sustainable healthcare solution for elderly care, addressing environmental and economic limitations of existing FPS technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3912-0
This erratum corrects an error in the Chinese name of co-first author Tianxiao Xiao (肖天孝) as originally published in the article 'A multi-modal smart chest patch for real-time cardiopulmonary monitoring and anomaly detection' (Sci China Mater, 2025, 68(12): 4413–4422). The corrected Chinese name is 肖天笑. The correction applies solely to the author's name and does not affect the scientific content, experimental data, or conclusions of the original paper. The authors and publisher apologize for any inconvenience caused.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60610-4
In this study, melamine and cyanuric acid were used as precursors to form supramolecular crystals via hydrogen-bond-assisted self-assembly followed by hydrothermal treatment. Subsequent high-temperature calcination yielded a novel brush-like three-dimensional carbon nitride. The brush-like 3D architecture was found to expose more accessible active sites, markedly accelerate electron transfer, and suppress the recombination of photogenerated charge carriers. The resulting superoxide (O2•−) and hydroxyl (•OH) radicals generated via electron reduction were identified as the key reactive species in the photocatalytic process. Moreover, the surface of the brush-like structure is enriched with nitrogen vacancies, which enhance the catalyst’s ability to harvest visible light. The photocatalytic performance of the brush-like CNS-650 catalyst was evaluated for rhodamine B (RhB) degradation. Under red-light irradiation (660 nm), its degradation rate was 7.4 times higher than that of bulk CN. This work provides valuable insights into the design and application of efficient metal-free 3D photocatalysts.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604011
Reverse osmosis (RO) membrane fouling remains a critical bottleneck in reclaimed water production, yet its spatial heterogeneity over extended operation is poorly understood. This study investigated fouling characteristics and microbial community dynamics on RO membranes after 3.5 years of operation in a full-scale microfiltration-reverse osmosis (MF-RO) system treating reclaimed water. Long-term monitoring showed stable effluent quality (turbidity <0.1 NTU, conductivity <400 μS/cm), but RO inlet pressure exhibited seasonal fluctuations of 15%–22% between summer and winter, attributed to water viscosity changes. Membrane autopsies revealed distinct fouling layers at the inlet (RO1) and outlet (RO2) ends. RO1 featured a dense bio-inorganic composite fouling layer with CaSO4 crystals and rod-shaped microbial aggregates (5–10 μm), dominated by Proteobacteria (77.11%), particularly Alphaproteobacteria (71.49%) and Xanthobacteraceae (35.29%), which secreted extracellular polymeric substances (EPS) to form biofilms. In contrast, RO2, exposed to higher salinity, showed reduced microbial abundance (Proteobacteria decreased to 64.79%) and a shift toward halotolerant taxa, including Microbacteriaceae (23.73%) and Actinobacteriota (24.76%), with EPS secretion increased by 42%. Alphaproteobacteria relative abundance dropped by 19.3%, while Gammaproteobacteria rose to 12.54%. These findings elucidate salinity-driven microbial succession and spatial heterogeneity of fouling, providing a basis for targeted antifouling strategies and 'zonal-graded' cleaning protocols in reclaimed water plants.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225191
Mg3Sb2-based materials, featuring a unique layered crystal structure, exhibit a favorable combination of low thermal conductivity, high Seebeck coefficient, and decent carrier mobility, establishing them among the most promising mid-temperature thermoelectric systems under active investigation. However, p-type Mg3Sb2 derivatives demonstrate a comparatively lower thermoelectric figure of merit (zT) compared to their n-type counterparts. Enhancing the zT performance of p-type Mg3Sb2 is therefore essential for the development of high-efficiency thermoelectric devices based on this material system. This review systematically summarizes the critical factors governing the thermal transport properties of p-type Mg3Sb2, including intrinsic characteristics such as chemical bonding and crystal structure, as well as extrinsic parameters such as carrier concentration, mobility, point defects, microstructure, and temperature dependence effects. Furthermore, it highlights recent advances in strategies designed to optimize thermal conductivity (κ) and improve zT, mainly including point defect engineering (such as Mg-site doping, Sb-site doping, dual-site co-doping, as well as doping-assisted composite modification), low-dimensional and nanostructural design, and advanced preparation technologies. Experimental studies demonstrate that these targeted strategies, particularly the synergistic introduction of multi-scale defects, can effectively suppress phonon propagation and significantly reduce lattice thermal conductivity (κL). Consequently, substantial improvements in the overall zT of p-type Mg3Sb2-based materials have been realized, providing a robust scientific and technical foundation for accelerating the practical application of Mg3Sb2-based thermoelectric devices.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508052
To improve the performance of pre-dust collectors in biomass boiler flue gas purification systems, a novel channel-steel baffle-type pre-dust collector was proposed to address the low collection efficiency of conventional designs. A gas-solid two-phase flow model was developed within the MP-PIC (multiphase particle-in-cell) framework and validated against physical experiments. The model simulated gas-particle motion inside the collector, systematically investigating the effects of structural modifications, flue gas conditions, and dust properties on collection efficiency and pressure drop. Results indicate that adding a flow baffle in the ash hopper and adopting an upper-inlet flue duct enhance collection efficiency with negligible impact on pressure drop. Flue gas velocity significantly influences performance: increasing velocity reduces efficiency while raising pressure drop; an optimal design velocity of 1.0–2.0 m·s−1 is recommended. Elevated flue gas temperature slightly decreases both efficiency and pressure drop, with minimal impact over a range of tens of degrees Celsius. Higher dust density and larger particle size improve collection efficiency and reduce pressure drop, whereas higher dust concentration increases both efficiency and pressure drop. The study elucidates the mechanisms by which structural and operational parameters affect pre-dust collector performance, providing theoretical guidance for designing low-resistance, high-efficiency collectors for biomass boilers.
Environmental Chemistry•2026•DOI: 10.0000/202605-1
A method for the determination of hydrazoic acid and sodium azide in workplace air was established using ion chromatography with suppressed conductivity detection. Vapor and mist states of hydrazoic acid were collected in 40 mg·L−1 KOH absorption solution, while sol states of hydrazoic acid or sodium azide were collected on microporous membranes and eluted with 40 mg·L−1 KOH. Separation was performed on a Dionex IonPac™ AS11-HC (250 mm × 4.0 mm) anion analytical column with KOH gradient elution, followed by suppressed conductivity detection. The azide ion (N3−) exhibited good linearity in the range of 0.005–0.5 mg·L−1, with a correlation coefficient (r) of 0.9997. The limit of detection (S/N=3) was 0.002 mg·L−1, and the limit of quantification (S/N=10) was 0.005 mg·L−1. The minimum quantifiable concentrations in air were 0.00256 mg·m−3 for hydrazoic acid and 0.00387 mg·m−3 for sodium azide, based on a 10.0 mL sample solution and a 20 L air sample. Spiked recoveries ranged from 92.0% to 100.4%, with relative standard deviations (RSD, n=6) between 0.76% and 2.51%. The method is efficient, accurate, and sensitive, suitable for monitoring and safety assessment of hydrazoic acid and sodium azide in workplace air.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605019
The utilization of food waste as a fermentation substrate can effectively reduce the substrate cost of lactic acid production industrialization, and synergistic fermentation with leachate could promote lactic acid production. However, the effect of magnesium ions in leachate on lactic acid production, metabolic processes, and key functional bacterial communities remains unclear. This study investigated the effect of adding magnesium ions on lactic acid fermentation using food waste as substrate. Results showed that the optimal magnesium ion dosage was 750 mg/L, achieving a lactic acid yield of (37.4±0.5) g COD/L and L-lactic acid optical activity of (96.3±0.9)%. Mechanistic studies revealed that magnesium ions accelerated substrate dissolution, significantly enhanced the activities of key hydrolytic enzymes (α-glucosidase, amylase, protease) and L-lactic acid producing enzymes, thereby increasing hydrolysis and lactate production rates. Simultaneously, the relative activity of lactate-consuming enzymes decreased, slowing lactate consumption. At 750 mg/L Mg2+, the relative abundances of Enterococcus and Streptococcus were 65.0% (2.2 times the Blank) and 18.7% (37.8% of the Blank), respectively, with a total of 83.7%, enhancing lactic acid yield and L-lactic acid optical activity. Metabolic pathway prediction and functional gene analysis further indicated that magnesium ions increased the relative abundance of carbohydrate metabolism pathways and genes encoding lactate dehydrogenase. This study provides technical support for food waste resource utilization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4105-8
Chiral europium(III) (Eu(III)) complexes, characterized by their f-f transitions and allowed magnetic dipole transitions, exhibit narrowband emission and superior circularly polarized luminescence (CPL) with high luminescence dissymmetry factors (g_lum), making them promising for circularly polarized organic light-emitting diodes (CP-OLEDs) and 3D displays. Here, we report a pair of R/S-Eu(TTA)3DFPO enantiomers, employing β-diketone 1,1,1-trifluoro-3-(2-thenoyl)acetone (TTA) as the main ligand and point-chiral R/S-tert-butyl(6-(diphenylphosphoryl)dibenzo[b,d]furan-4-yl)(phenyl)phosphine-oxide (R/S-DFPO) as ancillary ligands. In toluene, these enantiomers display characteristic narrowband red emission from the 5D0→7F2 transition of Eu(III), with a maximum emission wavelength of 617 nm, a full width at half maximum of 11 nm, a photoluminescence quantum yield of 43%, and pronounced chiroptical response, evidenced by |g_PL| values of 8.0 × 10^-3 around 590 nm (5D0→7F1 transition). Notably, CP-OLEDs fabricated via vacuum deposition achieve a maximum external quantum efficiency of 4.0% and exhibit obvious circularly polarized electroluminescence with |g_EL| values exceeding 1.0 × 10^-2. These results demonstrate that point-chiral phosphine-oxide ligands provide an effective strategy for achieving coordination-stable chiral Eu(III) complexes for high-performance CP-OLEDs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3933-9
The global cold chain consumes vast amounts of energy and emits greenhouse gases, while many regions lack proper refrigeration. To address this, we developed a dual-layer electrospun membrane (PZ-PML) for energy-free fruit preservation. The top PVDF-HFP/ZIF-8 layer offers 97.64% solar reflectance and 92.5% mid-infrared emissivity, providing 70 W/m2 radiative cooling. The bottom PAN/MIL-101/LiCl layer, with 2.18 g/g water uptake at 80% RH, delivers ~156 W/m2 evaporative cooling, lowering surface temperature by 6.1 °C under ~400 W/m2 irradiation. The membrane also shows ≥99% antibacterial efficiency against E. coli and S. aureus. Applied to strawberries, it reduced dehydration to 20.2% after 9 days, compared to 68.2% and 74.4% in controls. Additionally, it demonstrates durability, superhydrophobicity, and UV stability. This scalable solution offers energy-free fruit cooling, reducing postharvest losses while maintaining quality and safety.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3944-9
Hard carbon (HC) is a promising anode material for sodium-ion batteries (SIBs) but suffers from low initial Coulombic efficiency (ICE) and unstable solid electrolyte interphase (SEI). Here, we report a dual-functional strategy combining surface engineering and solution chemical pre-sodiation. A graphitic carbon coating on HC acts as a conductive buffer network and shields surface defects, while sodium biphenyl (Na-Bp) pre-sodiation drives sodium ions into the material via a potential difference, inducing a pre-SEI layer that matures into a thin, dense, NaF-rich inorganic SEI during cycling. This approach compensates for irreversible sodium loss and enhances cycling stability. The pre-sodiated electrode (pCH4-HC) achieves an ICE of 99.5% and a reversible capacity of 321.7 mAh g−1, compared to 54.2% for untreated HC. Long-term cycling shows 74.0% capacity retention after 1000 cycles at 300 mA g−1. In full-cells with NaNi1/3Fe1/3Mn1/3O2 (NFM) cathode, pCH4-HC||NFM delivers 81.9 mAh g−1 after 100 cycles, demonstrating excellent stability and rate performance. This dual-strategy approach validates the adaptability of pre-sodiation technology for high-performance SIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3769-2
Proton exchange membrane water electrolyzers (PEMWEs) are pivotal for sustainable hydrogen production, yet the corrosion-induced TiOx on porous transport layers (PTLs) introduces Schottky contact barriers and pinch-off effects, severely impeding charge transfer and efficiency. Here, a cost-effective MoIrOx coating via spray deposition and thermal treatment on Ti felts is proposed. The coating forms a conductive interlayer that establishes a Schottky barrier staircase, reducing the effective electron transfer barrier and isolating TiOx from the ionomer to mitigate the pinch-off effect. The optimal PTL achieves a current density of 3.27 A cm−2 at 2 V, surpassing uncoated Ti felts by 59.5%. The MoIrOx interlayer suppresses localized electron accumulation at the interface, enabling stable operation with ultra-low catalyst loadings by preventing direct ionomer-TiOx contact. This work demonstrates a scalable strategy to enhance PEMWE efficiency and durability while minimizing precious metal reliance, offering critical insights into interface engineering for electrolyzers.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511020
With the increasing number of oil pipelines crossing rivers, the potential risks of oil leakage and surface spreading to river ecosystems and water environments are becoming more severe. Scenario-based simulation of oil spill diffusion is a prerequisite for effective interception point placement and leakage risk prevention. Numerous factors influence oil spill diffusion, including environmental conditions, river hydrology, and accessibility of emergency resources. This study integrates these factors and multiple dynamic processes to design eight typical scenarios for oil spill diffusion simulation, considering emergency resource locations, river hydrological regimes, and leakage modes. A case study is conducted on an oil pipeline crossing a river in northwest China. Results indicate that the diffusion distance and affected area are primarily controlled by water conditions and emergency resource accessibility. In emergency management, the efficiency of maintenance and repair resources during high-water months should be prioritized. Mechanistically, external forces such as hydraulic and wind forces have a greater influence on diffusion distance, surpassing internal forces like gravity, viscosity, and surface tension within a short time. For river crossings near emergency resources, internal force effects should be considered in oil spill diffusion simulations. When emergency resource arrival times are long, the diffusion distance based on Fay's theory is relatively small and can be neglected in engineering practice. This study provides a computational basis and methodological reference for risk assessment and emergency response to potential oil spills from pipelines crossing rivers, enhancing the scientific and effective nature of risk prevention and emergency handling.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60639-1
Ni/Al2O3 is regarded as one of the most promising catalysts for industrial CO2 methanation, yet it suffers from inadequate low-temperature activity and thermal sintering. To address these challenges, an Ni/CaO-ZrO2-Al2O3 catalyst with high low-temperature activity and robust high-temperature sintering resistance was developed by introducing Ca and Zr promoters. Under reaction conditions of 250 °C and a space velocity of 30000 mL/(g·h), the catalyst achieved a CO2 conversion of 96% and a methane space-time yield of 257.5 mmol/(g·h). In a 200 h aging test at 600 °C, the Ca-Zr dual-promoted catalyst exhibited a smaller increase in Ni particle size and less activity loss compared to the Ca-promoted counterpart. Characterization revealed that Ca and Zr promoters not only improve Ni dispersion but also enhance surface basicity, contributing to excellent low-temperature activity. Furthermore, Zr suppresses the transformation of Ca species into CaCO3 via solid-phase reaction under operating conditions, thereby inhibiting Ni sintering and ensuring high-temperature stability. This work provides a novel promoter design strategy for developing high-performance Ni-based catalysts for CO2 methanation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3825-x
Polymer-based dielectric materials with high energy density and thermal stability are critical for modern electric/electronic industries. Polyimide (PI) based materials are promising due to their high temperature resistance and chemical inertness, yet their inherently low dielectric constant and limited charge-discharge energy density restrict applications in film capacitors. While incorporating ferroelectric or conductive fillers can enhance dielectric performance, batch-to-batch inconsistency and physical deterioration remain problematic. This study focuses on molecular structure design and modulation, preparing hyperbranched polyimides with different dianhydride monomers and branching degrees. The effects of chain packing density with polar groups on dielectric and energy storage performances were systematically investigated via experimentation and molecular simulation. Results demonstrate a significant correlation between monomers' electrical distribution and packing density in polymer systems. Molecular simulation further elucidated the underlying mechanism. This work establishes a foundation for designing polymer-based dielectric materials with high dielectric and energy storage performances at the molecular level.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60655-X
Defect-induced nonradiative recombination critically restricts the power conversion efficiency (PCE) and stability of perovskite solar cells (PSCs). Lewis base additives show great promise in defect passivation, but current screening methods rely heavily on empirical trial and error and lack clear design principles, making it difficult to efficiently discover high-performance candidate materials. Here, we present a machine learning (ML) framework to intelligently screen Lewis base molecules for defect passivation. We trained six ensemble models on a dataset of 146 experimental data points, with Light Gradient Boosting Machine (LightGBM) yielding the best classification performance (87% accuracy). Shapley Additive Explanations (SHAP) interpretability analysis subsequently identifies the highest occupied molecular orbital (HOMO) energy (−7.5 to −6.3 eV), additive concentration (2.5 to 6.5 mg/mL), and simplified molecular backbones (O atom ≤ 2, C atom < 5) as critical design criteria. The ML prediction was experimentally validated: (S)-pyrrolidine-3-carboxylic acid ((S)-PCA) and 2-methyl-1,3-cyclopentanedione (MCPD) (Class Ⅱ) improved PCE by 2.22% and 2.01%, respectively, while 3-hydroxymethyl-3-methylbutanenitrile (3-HMBN) (Class Ⅰ) showed minimal gain. Density functional theory (DFT) calculations further confirmed the stronger binding affinities and elevated defect formation energies of Class Ⅱ additives. Notably, the champion (S)-PCA device achieved a PCE of 24.05%. This work established an ML-accelerated paradigm for the rational design of defect passivators, bridging data science and photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3987-x
A hierarchically porous nickel salicylate (Ni-SA) metal-organic framework (MOF) was constructed via a salicylate coordination strategy to precisely modulate the microenvironment of nickel active sites for efficient electrocatalytic glucose oxidation. The ortho-hydroxy-carboxylate chelation directs atomic-level organization of Ni2+ sites within nanobelt assemblies, maximizing active site accessibility. Robust Ni–O coordination stabilizes Ni3+ intermediates during C–H bond cleavage, leading to remarkable catalytic stability. The optimized Ni-SA-2 catalyst achieved a high sensitivity of 5.97 mA mM−1 cm−2 and a low detection limit of 0.71 μM (S/N = 3), with 85.4% current retention after 8 h continuous operation. This design paradigm demonstrates universal applicability, as evidenced by successful extension to isostructural M-SA analogs (M = Co, Fe, Cr, Mn) under identical synthetic conditions, establishing metal-salicylate frameworks as a versatile electrocatalyst platform.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3998-8
Constitutional isomerism in covalent organic frameworks (COFs) has emerged as a powerful strategy to tailor material properties for photocatalytic applications. Here, we report the design and synthesis of two isomeric multicomponent COFs (MC-COFs) via Schiff-base condensation followed by Povarov reaction, converting imine linkages into quinoline structures. These isomeric MC-COFs exhibit opposing C=N bond orientations and distinct phenyl group alignments within the COF pores, leading to different torsion angles in the COF layers. Structural analyses reveal that enhanced planarity promotes π-π stacking and electron delocalization, resulting in favorable band structures and reduced exciton binding energies. Consequently, the optimized COF achieves a superior hydrogen peroxide (H2O2) production rate of 3128 μmol g−1 h−1 under visible light irradiation. This work underscores the critical influence of structural isomerism on the photocatalytic efficiency of MC-COFs and provides insights for rational design of high-performance COF-based photocatalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4077-0
Flexible memristors are pivotal for advancing neuromorphic computing in wearable electronics, yet the intrinsic brittleness of inorganic oxides poses a critical challenge. Here, we employ an entropy-engineering strategy to control the amorphization of oxide compositions, yielding a precisely controlled crystalline/amorphous microstructure in a BaTi0.25Sn0.25Hf0.25Zr0.25O3 thin film. This film withstands bending angles up to 180°, enabling an Au/BaTi0.25Sn0.25Hf0.25Zr0.25O3/ITO/Mica device that functions as a memristor. Entropy engineering increases oxygen vacancy concentration, imparting stable resistive switching behavior under both flat and bent conditions. The device exhibits exceptional endurance and reproducibility over multiple bending cycles, demonstrating a significant strategy for advancing flexible memristor technologies and holding promise for next-generation high-performance flexible electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4038-8
Fluorescent fibers and textiles that integrate outstanding optical performance with excellent flexibility hold significant promise for wearable applications and the Internet of Things (IoT). However, the poor stability of post-organized phosphor-based fibers and the high-cost, high-precision technology of electroluminescent fibers hinder their widespread adoption. Perovskite materials and organic semiconductors, owing to their high-efficiency, tunable luminescent properties and solution processability, are deliberately employed to fabricate desired fluorescent fibers and textiles via a spinning chemistry strategy. Recent advances have successfully applied these fibers to sensors, information displays, optical communications, and health monitoring. This review provides a comprehensive overview of recent progress in fluorescent fibers and textiles, covering spinning techniques, emitter design, and wearable applications. We highlight key challenges and future research directions in the fine design and synthesis of fluorescent fibers and textiles, as well as their system integration for practical wearable applications. The review emphasizes the potential of spinning chemistry to enable scalable production of robust, high-performance luminescent fibers, addressing stability and cost barriers. We discuss the use of metal halide perovskite quantum dots (PQDs) with high photoluminescence quantum yields (PLQY) and tunable emission, and organic semiconductor emitters with tailored molecular structures, as promising building blocks. The integration of these materials into fibers via spinning chemistry offers a facile, efficient, and controlled strategy, leading to ultra-stable CsPbX3 (X = Cl, Br, I) perovskite filaments with a PLQY of 24.5% and stretchability up to 2400%. The review concludes by outlining future research directions, including the development of lead-free perovskites and self-healing materials, to enhance stability and safety for commercial wearable technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4146-8
The conventional trial-and-error approach for the research and development (R&D) of high-performance super-hydrophilic coatings presents long-standing challenges, including data scarcity, unclear structure-activity relationships, and lack of design guidelines. In this study, an innovative multi-model framework that synergistically integrates a specialized polymer large language model (PolyLLM) and a polymer machine learning model (PolyML) for intelligent R&D of super-hydrophilic coating systems is designed and demonstrated. During the hydrophilic polymer research phase, the multi-model leverages the domain-specific insights and chemical tool capabilities of the fine-tuned PolyLLM to systematically screen 852 hydrophilic monomers and generate 3880 hypothetical polymer architectures. By utilizing the PolyML, the multi-model enables precise performance predictions and quantitative evaluations of feature importance to facilitate efficient high-throughput screening of optimal structures from the generated polymer database. Experimental validation confirms that the multi-model achieves a mean absolute error (MAE) below 10% across various polymer property prediction tasks compared to experimental data. This approach leads to the rapid discovery of hydrophilic polymers with exceptional anti-swelling and wear-resistance. In developing super-hydrophilic coatings, the multi-model effectively combines PolyLLM's guidance for large-scale synthesis with PolyML's capabilities for precise formulation optimization and curing parameter adjustments. The effectiveness of multi-model is demonstrated by the accelerated development of high-performance anti-fogging coatings for swim goggles and optical films with outstanding water- and wear-resistance that significantly outperform leading commercial products. This multi-model offers a flexible approach for advanced polymer coatings, leading to a seamless connection between laboratory research and industrial development.