Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604016
River and lake health assessment is an important technical means to evaluate the health status of rivers and lakes, scientifically analyze river and lake problems, and strengthen the implementation of the river and lake head system. Based on the Guidelines for River and Lake Health Assessment (Trial) and the characteristics and actual basin conditions of the lower Yellow River in Henan, this study determined the river health evaluation index system for this reach. Through collection of basic data and special investigations and monitoring, the health status in 2020 was evaluated from four criteria layers: 'basin', 'water', biology, and social service function. The overall score was 83.4, corresponding to a 'healthy' grade. The four criteria layer scores were 73.7, 95.0, 62.1, and 95.5, respectively. The evaluation identified main problems including low aquatic biodiversity, suboptimal shoreline conditions, and pressure on water supply security. Corresponding governance and protection measures were proposed, such as strengthening ecological protection, improving river regulation works, enhancing shoreline management, and upgrading water diversion facilities. The results provide scientific basis for river health management and the implementation of the river chief system in the lower Yellow River.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3786-8
Conventional cancer diagnostic techniques, such as tissue sampling and microscopy, are invasive and prone to misdiagnosis, driving the need for non-invasive, precise alternatives. Chiral biophotonics, exploiting circularly polarized light (CPL), offers unique polarization-selective interactions with biological tissues, enabling higher imaging contrast and molecular-level discrimination. However, current CPL detection technologies are passive and single-mode, lacking dynamic tunability and parallel processing capabilities. Meanwhile, AI-assisted diagnostics rely on separated sensing and computing units, suffering from poor integration and transmission inefficiency. Here, we report a near-infrared (NIR) chiral organic synaptic photodiode with electrically tunable dual-mode operation, enabling simultaneous CPL detection and neuromorphic processing. Under negative bias, the device operates as a highly sensitive CPL detector for chiroptical signal acquisition. Under positive bias, it exhibits history-dependent synaptic behavior with photocurrent dissymmetry factor (g_ph) dynamically tunable up to -0.06. By integrating this device into an optical convolutional neural network (OCNN), we achieved intelligent cancer detection with CPL-based imaging. Experimental results demonstrate that CPL detection accuracy reaches 83%, approaching the theoretical 87%, significantly outperforming natural light detection at 65%. The device enhances image contrast and feature extraction, laying a foundation for intelligent, adaptive diagnostic systems.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606006
Chitosan-based microsphere composites have attracted considerable attention for phosphorus adsorption due to their facile preparation, low cost, environmental friendliness, and high uptake capacity. This review summarizes the physicochemical properties and preparation methods of chitosan microspheres for phosphate removal, outlines common modification strategies to enhance adsorption capacity, and discusses their applications in aqueous environments. Adsorption mechanisms, regeneration, and resource recovery of spent microspheres are analyzed. Challenges and recommendations are proposed, including streamlined preparation, enhanced phosphorus recovery, removal of multiple phosphorus forms, and practical implementation. The review aims to guide the development of high-performance chitosan-based microspheres for phosphorus removal.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3774-3
Lithium-air capacitor batteries (LACBs) integrate the rapid charge-discharge capability of supercapacitors into conventional lithium-oxygen batteries, significantly enhancing power density. However, their cycling stability remains unsatisfactory. In this study, we incorporated redox mediators (RMs) into an LACB featuring a dual-cathode configuration. This design facilitates sustained electron transfer between the electrode and Li2O2/Oxygen, thereby delaying RM deactivation caused by electrode passivation and improving overall electrochemical performance. The RM-enhanced battery achieved over 250 cycles at 2 mA cm−2 with a limited capacity of 0.5 mAh cm−2, while exhibiting a 0.54 V reduction in charging voltage at 0.1 mA cm−2 compared to the RM-free system. Furthermore, application of an aluminum foil sealing technique enabled a power density of 13.8 mW cm−2 at 6 mA cm−2, overcoming mass transport limitations inherent in open-cell configurations. We also investigated the influence of oxygen barrier films with varying barrier capabilities on LACB performance. Results indicate that films with superior oxygen resistance better maintain a clean capacitor electrode surface, thereby providing more stable electron supply to the RMs and enhancing rate capability and cycling performance. These findings underscore the potential of redox mediators in improving the performance and longevity of LACBs, offering a promising strategy for their future development.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60656-1
Under the carbon neutrality strategy, biomass boilers have emerged as key facilities for renewable energy utilization, yet are characterized by low-concentration SO2 emissions. Ca-based dry desulfurization presents a promising technology for biomass boiler flue gas purification due to its compact structure, low capital investment and simple operation and maintenance. However, it is generally limited by the low adsorbent utilization and insufficient desulfurization efficiency. Herein, this study developed a novel Ca-Mn composite adsorbent through a synergistic strategy integrating F127 surfactant to optimize dispersion and Mn loading to enhance oxidation efficiency. The resulting adsorbent not only significantly increased the breakthrough sulfur capacity of the Ca-based material but also markedly improved the synergistic removal of Hg0. It was demonstrated that the introduction of Mn elements and F127 effectively suppressed the agglomeration of Ca(OH)2 crystallites and induced an oxygen vacancy-rich structure, while simultaneously optimizing the pore structure of the adsorbent. The modified adsorbent exhibited the enlarged specific surface area and pore volume, which favored to enhance the reaction mass transfer and effectively prevent the pore blockage and coverage of active sites by desulfurization products. The Mn sites and oxygen vacancies formed catalytic centers, which not only accelerated the desulfurization reaction by promoting SO2 oxidation but also enabled the adsorbent to couple with Hg0 catalytic oxidation functionality. Consequently, the simultaneous removal of SO2 and Hg0 was significantly enhanced on the Ca-Mn composite adsorbent.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4085-9
Bone defects remain a prevalent clinical challenge, and regenerative medicine based on bone tissue engineering offers promising solutions. Traditional osteogenic materials rely on bioactive macromolecules like growth factors, which suffer from poor stability and stringent storage requirements. From a structural perspective, bone tissue resides in a phosphorylated microenvironment, with 65–70% of inorganic components composed of hydroxyapatite. Inorganic phosphorylated materials induce osteogenic differentiation but exhibit high stiffness, brittleness, slow degradation, and limited mechanical tunability. Synthetic phosphorylated polymers with excellent mechanical properties and biocompatibility have been developed to address these issues. In this work, we developed a series of phosphorylated polymers derived from poly(glycerol sebacate) (PGS), a biocompatible and biodegradable material. Leveraging the hydroxyl-rich backbone of PGS, we demonstrated an efficient method for controllable phosphorylation of PGS side chains, enabling synthesis of PGS-based phosphorylated (PGS-P) polymers with tunable phosphorus contents. The optimized phosphorylated polyester, PGS-P4, exhibited strong ability to promote osteogenic differentiation of rat BMSCs, and its porous three-dimensional scaffolds showed favorable properties for bone regeneration. BMSCs cultured for one week and observed by fluorescence microscopy showed enhanced BSP protein expression on PGS-P2, PGS-P4, and PGS-P6 groups compared with PLGA and PGS, with PGS-P4 displaying the most intense signal. In summary, we present a simple and controllable method for preparation of functionalized polyesters and their porous scaffolds with tunable phosphorus content, validating its effectiveness in promoting osteogenic differentiation of rat BMSCs. All phosphorylated polyesters exhibit enhanced differentiation-promoting effects compared to non-phosphorylated PGS; however, the degree of enhancement does not increase monotonically with phosphorus content. PGS-P4, containing an optimal phosphorus level, shows the most pronounced biological functions.