SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4500-8
Electroreduction of CO2 to ethylene offers a promising route for renewable electricity storage, yet achieving high ethylene selectivity at industrial current densities remains challenging due to the large energy barrier for C–C coupling. Here, we report a “MOF-assisted in situ doping” strategy to introduce the oxophilic nonmetal phosphorus (P) into the copper oxide (CuO) lattice, constructing a localized Cu–P dual-site adsorption configuration for the key *OCCHO intermediate. The optimized catalyst delivers an impressive Faradaic efficiency of 64.6% for ethylene with a partial current density of 646 mA cm-2. Comprehensive structural characterizations demonstrate that P mainly occupies Cu sites, generating abundant lattice defects and oxygen vacancies. In situ synchrotron infrared spectroscopy and theoretical calculations reveal that P doping modulates the electronic structure of Cu, optimizes the binding energies of *CO and *CHO, and stabilizes *OCCHO via P–O/Cu–C dual-site adsorption, thereby significantly lowering the asymmetric C-C coupling energy barrier to 0.74 eV. This work highlights a dual-site microenvironment regulation strategy for CO2-to-ethylene electroreduction.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4321-x
Poly(ethylene oxide) (PEO)-based solid polymer electrolytes are leading candidates for solid-state lithium metal batteries due to their flexibility, processability, and interfacial compliance. However, the strong crystallization tendency of PEO and limited lithium salt dissociation result in low ionic conductivity and low Li+ transference number, exacerbating concentration polarization and interfacial instability. Introducing metal-organic framework (MOF) fillers into PEO matrices has emerged as an effective route to regulate polymer-chain packing and promote salt dissociation via Lewis acid-base interactions. Yet, most studies focus on cubic ZIF-8, whose saturated Zn coordination environment limits intrinsic Lewis acidity and restricts its ability to immobilize TFSI- anions. Simultaneously, simple physical blending often leaves discontinuous interfacial transport regions in composite electrolytes, so improved salt dissociation does not automatically translate into fast Li+ transport. Here we report a PEO-based composite polymer electrolyte, denoted as PZS, that couples monoclinic ZIF-8 (M-ZIF-8) nanosheets with a thin SiO2 layer. The design combines two complementary functions: the under-coordinated Zn sites in M-ZIF-8 provide strong Lewis acid centers to adsorb TFSI- and promote LiTFSI dissociation, while the hydroxyl-rich SiO2 shell improves compatibility with the PEO matrix and helps construct continuous interfacial Li+ transport pathways. Benefiting from this synergy, the optimized PZS electrolyte delivers an ionic conductivity of 8.3 × 10-4 S cm-1 and a Li+ transference number of 0.57 at 60 ℃, together with an electrochemical stability window of 5.2 V. Li||Li symmetric cells remain stable for over 1200 h at 0.1 mA cm-2, and LFP||Li full cells retain 80% of their capacity after 400 cycles at 0.5 C.
Nano Research Energy•2026•DOI: 10.26599/NRE.2025.9120181
Solid-state lithium metal batteries (SLMBs) demand quasi-solid polymer electrolytes (QSSPEs) that simultaneously deliver high ionic conductivity, interfacial stability, and oxidative resistance. This study reports a QSSPE membrane (MP46) formulated with MG30:LiTFSI:succinonitrile at a 10:4:6 weight ratio, exhibiting a wide electrochemical window of 5.1 V. Complementary infrared spectroscopy, small-angle X-ray scattering, and electron microscopy reveal a hierarchical ionic conductive network consisting of sphere-like nanostructures embedded within microphase-segregated architectures. This morphology enhances lithium-ion transport while preserving mechanical integrity. The strong interfacial adhesion between MP46 and lithium metal enables stable lithium plating and stripping for over 800 h at 0.2 mA·cm–2, effectively mitigating dendrite formation. When paired with LiFePO4 and LiCoO2 cathodes, MP46 sustains prolonged cycling, retaining 80.1% capacity after 1400 cycles at 2 C and 92.1% after 200 cycles at 4.5 V, respectively. Pouch-type cells further demonstrate mechanical flexibility and operational safety under deformation. These results establish MP46 as a viable candidate for stable high-energy-density SLMBs, offering fundamental insights into the design of next-generation polymer electrolytes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4290-9
Thermoelectric materials enable direct and reversible conversion between heat and electricity, offering unique advantages for waste heat recovery, solid-state refrigeration, and deep-space power systems. The performance is evaluated by the dimensionless figure of merit, zT = S²σT/κ, where S is the Seebeck coefficient, σ is the electrical conductivity, T is the absolute temperature, and κ is the total thermal conductivity. Achieving high zT requires simultaneous realization of a large power factor (S²σ) and low thermal conductivity. However, these parameters are intrinsically coupled, posing a fundamental challenge. PbTe is a representative thermoelectric material operating in the intermediate temperature range, with outstanding performance originating from its unique electronic band structure featuring multiple nearly degenerate valence band maxima near the L points. Band convergence via alloying with mono-tellurides such as MgTe, MnTe, CdTe, YbTe, SrTe, and EuTe effectively modifies the valence band structure, increasing band degeneracy and density-of-states effective mass, thereby enhancing electrical conductivity without decreasing the Seebeck coefficient. However, increasing the content of these mono-tellurides limits acceptor dopability, making conventional dopants like Na difficult to incorporate. This study demonstrates that co-doping strategies can preserve dopability while achieving band convergence and dislocation engineering, leading to significantly reduced lattice thermal conductivity and extraordinary peak zT values. The decoupling of electronic and thermal transport through this approach offers a promising route for high-performance thermoelectrics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4315-2
High-temperature X-ray imaging demands scintillators with high crystallinity, efficient scintillation, and robust thermal stability, yet suitable materials remain scarce. Here, we report an ultra-high-crystallinity transparent glass-ceramic (GC) scintillator strategically designed via controllable heat-treatment-induced crystallization. A sequential precipitation method is employed, where cubic CaF2 nanocrystals initially form, subsequently promoting heterogeneous nucleation and growth of hexagonal BaAl2Si2O8. Intrinsic nanoscale phase separation into F-rich and O-rich domains significantly reduces atomic diffusion distances, yielding an unprecedented crystallinity of up to 97.6%. Notably, defect traps (oxygen vacancy defects, likely located within the lattice or at crystalline/amorphous interfaces) enable efficient carrier capture and thermally stimulated release, contributing to remarkable resistance to thermal quenching. Consequently, the GC scintillator maintains 90.6% of its integrated X-ray excited luminescence (XEL) intensity at 300 °C, with the integrated XEL intensity reaching 94.2% of commercial Bi4Ge3O12 (BGO) at room temperature. This enables stable high-temperature X-ray imaging with a spatial resolution of ~10.4 lp mm−1 up to 225 °C. This work provides a versatile pathway for developing high-sensitivity scintillators for extreme-environment X-ray imaging.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4322-4
Ultrafast scintillators with low-nanosecond emission are essential for next-generation high-rate X-ray and particle imaging. Although Ce3+-activated scintillators inherently exhibit fast response characteristics, conventional Ce3+-doped hosts rarely achieve low-nanosecond ultrafast decay. Here, we report a high-entropy fluoride scintillator (HEFS), Ce:LaGdCaSrBaF12 (Ce:LGCSB), in the form of bulk single crystals. The severe lattice distortion arising from multi-cation disorder induces exciton localization and effectively suppresses exciton diffusion. Through the rapid relaxation of localized excitons, the high-entropy Ce:LGCSB single crystals deliver a decay time of 1.23 ns with a 94.6% fast-component contribution and without any noticeable slow component. Through first-principles calculations, spectroscopic characterization, and transient dynamics analysis, we reveal that the ultrafast response originates from accelerated Frenkel exciton (FE) recombination enabled by the high-entropy environment. This work establishes entropy-engineered fluorides as promising ultrafast scintillator platforms and proposes a general strategy for extending sluggish diffusion effects to the excitonic scale, offering new opportunities for improving scintillation timing performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3888-9
Flexible thermoelectrics (f-TEs) are being developed rapidly due to their unique advantages, such as direct conversion between electricity and thermal energy, compatibility with curved heat sources, and ease of integration. Over the past decade, significant progress has been made in enhancing the overall performance of f-TE materials and devices, particularly in terms of output power, mechanical flexibility, and durability. Recent research efforts are increasingly focused on translating these advancements into practical applications across diverse fields. For example, f-TE-based multimodal sensors are capable of simultaneously detecting temperature, pressure and strain. In biomedicine, f-TE generators are being explored for wound healing, antibacterial therapy, and neural modulation. Furthermore, f-TE devices show promise in personalized thermal management and hybrid energy harvesting systems. This review moves beyond material preparation and device optimization to focus on the expanding multifunctional applications of f-TEs. We provide a broad perspective by comprehensively exploring the latest progress of f-TEs in intelligent sensing, biomedicine, personalized thermal management, and multifunctional hybrid systems. Key challenges are also discussed, including the development of high-performance flexible devices, robust bio-interfaces, ensuring long-term stability, and achieving intelligent integration with data-driven algorithms and multimodal platforms. Finally, we offer insights into future directions for f-TEs, pointing toward next-generation intelligent and bio-integrated flexible electronics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3927-9
The mechanical properties of as-cast TiAl alloys are severely limited by their coarse as-cast microstructure. This study proposes a low-temperature pre-deformation heat treatment to refine the microstructure of an as-cast Ti-47Al-2Nb-2Cr alloy. The process involves pre-deformation below the eutectoid temperature followed by heat treatment in the α+γ phase field, yielding two distinct microstructures: duplex (DP) and nearly lamellar (NL). The average lamellar colony size was reduced to 5.3% and 20% of the as-cast size for DP and NL structures, respectively. Microstructural evolution analysis reveals that the decomposition of coarse lamellar colonies and the formation of fine grains are governed by γ recrystallization, γ→α phase transformation, and α recrystallization. Remnant colonies after deformation are completely eliminated by subsequent heat treatment, enhancing microstructural homogeneity and mechanical properties. The DP alloy exhibits an ultimate tensile strength (UTS) of 537 MPa and an elongation (EI) of 6.8% at 800°C, representing increases of 44.7% and 518.2% over the as-cast alloy, respectively. Analysis of crack propagation and deformation mechanisms indicates that grain refinement and lamellar structure refinement contribute to improved deformation ability. This work provides a viable pathway for optimizing as-cast TiAl alloys for high-temperature applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4043-3
In-plane InAs nanowires and nanowire networks are promising platforms for electronics, optoelectronics, and topological quantum computing due to their small electron effective mass, narrow bandgap, high electron mobility, strong spin-orbit coupling, and large Landé g factor. However, their selective area growth on CMOS-compatible group-IV substrates remains challenging. Here, we report the selective area growth of high-quality in-plane InAs nanowires and nanowire networks on Ge(111) substrates by molecular-beam epitaxy. Conventional selective-area epitaxy fails to simultaneously achieve good selectivity and continuity. To overcome this, we developed a metal-sown, single-indium-source two-step growth method, which attains both selectivity and continuity but yields nanowires with rough surfaces and lengths below 10 μm. We then introduced an upgraded metal-sown, dual-indium-source two-step growth method, successfully fabricating in-plane InAs nanowires and nanowire networks with smooth surface morphology and lengths exceeding 60 μm. By optimizing the As beam equivalent pressure, overgrowth at network junctions is effectively suppressed, resulting in uniform nanowire networks. High-resolution transmission electron microscopy and Raman spectroscopy confirm the high-quality single-crystalline nature and pure zinc-blende structure of the nanowires and networks. This work establishes a foundation for fabricating high-quality in-plane InAs/superconductor hybrid nanowires and nanowire networks on Ge substrates.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3856-0
Replacing the kinetically sluggish oxygen evolution reaction (OER) with biomass oxidation at photoanodes offers a cost-effective and energy-efficient route for simultaneous hydrogen production and value-added chemical synthesis in a photoelectrochemical (PEC) cell. Here, titanium-doped hematite nanorods (Hem) decorated with CoNi bimetallic zeolitic imidazolate frameworks (ZIF) were prepared via room-temperature deposition and employed as photoanodes for 5-hydroxymethylfurfural (HMF) oxidation. Using 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO) as a redox mediator in alkaline electrolyte, the CoNi-ZIF/Hem photoanode achieved a photocurrent density of 1.09 mA cm−2 at a low bias of 1.1 V vs. reversible hydrogen electrode (RHE). Experimental results and theoretical calculations reveal that CoNi-ZIF accelerates charge transfer and separation, and enhances TEMPO adsorption on the surface, benefiting PEC TEMPO-mediated HMF oxidation to 2,5-furandicarboxylic acid (FDCA). In a flow-cell reactor under 1 sun illumination, the photoanode achieved ~99% HMF conversion and ~98% FDCA yield within 2 hours. The photoanode also exhibited excellent performance for TEMPO-mediated oxidation of various aldehyde-containing biomass-derived compounds. This work demonstrates a rational design of hematite-based photoanodes for efficient biomass valorization coupled with hydrogen production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3545-7
Magnetically driven hydrogel robots show promise in biomedical and underwater applications due to remote controllability, flexibility, biocompatibility, and chemical stability. However, limited functional integration restricts their adaptability. Here, a universal modular assembly strategy is introduced using a self-healing κ-carrageenan/polyacrylamide hydrogel embedded with magnetic particles, enabling free assembly of magnetic actuation modules. These modules construct soft robots with complex geometries and magnetization distributions, allowing diverse deformations under magnetic fields. The strategy further integrates photocatalysis by embedding Ru-Bi2CrO6 photocatalysts into functional modules, yielding an oxygen-generating robot. This robot exhibits flexible underwater movement via magnetically controlled oscillatory actuation, minimizing water agitation while supplying stable oxygen to specific aquatic environments. The photocatalytic oxygen evolution rate reaches 389.1 μmol g−1 h−1. The hydrogel skeleton suppresses particle aggregation and sedimentation, and facilitates magnetic recovery. This scalable and adaptable approach advances multifunctional soft robot design.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61104-3
Lithium/fluorinated carbon (Li/CFx) batteries are among the most promising high-energy-density primary batteries, yet substantial heat generation during discharge poses safety concerns, particularly for high-mass-loaded pouch cells. This study systematically investigates the effects of fluorination temperature on the structure and kinetics of fluorinated porous carbon (FPC) cathodes and on heat generation in Ah-level Li/FPC pouch cells. FPC samples with varying degrees of fluorination were synthesized by adjusting fluorination temperature, which influenced not only the F/C ratio but also the C–F bonding configuration, pore structure, and electronic transport capability. Pouch cells employing more highly fluorinated cathodes generated the most heat during discharge, with heat generation exhibiting clear stage dependence, predominantly in the 0–20% depth of discharge (DOD) range. Post-discharge structural characterization and kinetic analysis revealed that highly fluorinated FPC cathodes (FPC-250) undergo more concentrated LiF accumulation, leading to higher charge-transfer resistance, stronger polarization, lower Li+ diffusivity, and higher nucleation overpotential. These factors collectively intensify early-stage heat generation. The study establishes a correlation between fluorination temperature and cathode structure, discharge-product evolution, discharge kinetics, and heat generation, demonstrating that regulating fluorination temperature is an effective strategy for improving the thermal safety of Li/CFx batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3650-6
Aggregation-induced emission active chiral polymer dots (AIE@CPdots) are emerging as high-performance emission layers (EMLs) for circularly polarized organic light-emitting diodes (CP-OLEDs) due to their persistent emission stability, high photoluminescence quantum yields, excellent solution processability, facile functionalization, tunable bandgap-governed emission, and superior device processability. However, reports on such systems remain scarce. In this study, a pair of chiral conjugated polymer enantiomers (R/S-PFC) was synthesized via Suzuki polymerization using three monomers: a chiral binaphthalene moiety, a fluorenyl linker, and an AIE-active cyanostyrene dye. After annealing at 110 °C, the resulting R/S-PFC self-assembled into chiral nanoparticles (AIE@CPdots) in a chloroform/n-hexane mixed solvent (9:1 v/v), exhibiting enhanced circularly polarized luminescence with a luminescence dissymmetry factor (|g_lum|) of 4.4 × 10⁻³ at 462 nm. Notably, AIE@CPdots served as the EML in CP-OLEDs, achieving high-performance circularly polarized electroluminescence with an electroluminescence dissymmetry factor (|g_EL|) of 3.0 × 10⁻³ at 464 nm, a maximum luminance (L_max) of 6022 cd m⁻², and a maximum current efficiency (CE_max) of 1.10 cd A⁻¹. This work provides a novel strategy for designing superior EML materials for CP-OLEDs via chiral self-assembled AIE@CPdots.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3801-1
Traditional phase transition gel platforms face significant challenges in achieving time-gated information encryption and decryption. Here, we report a photocleavable gel that enables time-gated information encryption and decryption, enhancing information storage security. The gel is synthesized by copolymerization of hydrophobic ortho-nitrobenzyl acrylate (NA) and acrylamide. Upon ultraviolet (UV) irradiation, hydrophobic NA units partially cleave to yield orange-colored o-nitrosobenzaldehyde (NSBA) molecules and hydrophilic acrylic acid groups, altering local color and hydrophilicity. Information is spatially encoded using a photomask. The written information is encrypted by dissolving NSBA molecules in dimethyl sulfoxide (DMSO). Upon aqueous immersion, differential hydrophilicity between irradiated and non-irradiated zones triggers localized phase separation, facilitating decryption. Notably, photolysis kinetics is time-gated, ensuring decryption only within a specific time window in water. This method surpasses traditional gel constraints, offering a novel paradigm for secure information storage.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509067
Marine litter poses a significant threat to coastal ecosystems globally, necessitating a comprehensive understanding of its multi-compartment distribution and driving mechanisms for effective management. This study investigated the occurrence, composition, and sources of beach, sea surface, and seafloor litter in the northeastern Daya Bay, a semi-enclosed bay, during August–October 2024. Sampling included 11 beach transects, 6 surface transects, and 25 seafloor transects. Results showed that the mean density of large and very large beach litter was 4.41×10^5 items·km−2, while medium beach litter reached 5.39×10^6 items·km−2. Surface litter densities were 5.82×10^2 and 9.90×10^3 items·km−2 for large/very large and medium fractions, respectively. Seafloor litter averaged 5.20×10^3 items·km−2. Plastics dominated all compartments, accounting for 74.0% (beach), 96.0% (surface), and 78.8% (seafloor) of total litter. Source apportionment using NOWPAP methodology indicated that beach and surface litter primarily originated from coastal recreational activities, whereas seafloor litter was mainly derived from shipping and fishing. Beach quality assessment revealed that 63.6% of beaches were moderately clean or better (grade II–IV), and 90.9% were moderately safe or better (grade I–III). Hotspots included tourism beaches, tidal gyre areas, coral reef zones, and fishing grounds. The study underscores the need for targeted management, including improved waste collection on tourist beaches, dynamic cleaning protocols, and port reception facilities for fishing waste.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60618-9
Aromatic hydrocarbons, essential chemical feedstocks for fuels, synthetic fibers, and pharmaceuticals, are predominantly derived from petroleum refining. The catalytic conversion of lignin, a major lignocellulosic component, offers a renewable route to these chemicals. This review systematically examines the influence of pyrolysis methods, catalysts, and reaction conditions on the catalytic pyrolysis of lignin to aromatic hydrocarbons. Key parameters include catalyst acidity and pore structure, which govern selectivity and yield. Reaction temperature, catalyst-to-lignin ratio, and residence time critically affect product distribution. The review outlines catalytic mechanisms, such as deoxygenation, cracking, and aromatization, and highlights the role of zeolite catalysts, particularly HZSM-5, in enhancing monocyclic aromatic hydrocarbon yields. Metal modification (e.g., Fe, Ni, Ga) and pretreatment strategies (e.g., torrefaction) are discussed for improving efficiency. Challenges remain in catalyst deactivation due to coking and the complexity of lignin structure. Future research directions include developing robust catalysts, optimizing reactor designs, and integrating processes for industrial viability. This review provides theoretical and technological guidance for advancing lignin-to-aromatics conversion.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025022501
The pretreatment of trace emerging contaminants in environmental matrices is challenging due to diverse methods and uncertain applicability. This study compared solid-phase extraction (SPE) and liquid-liquid extraction (LLE) for extracting endocrine-disrupting compounds (EDCs), particularly phthalate esters (PAEs), using laboratory-spiked blank samples. LLE achieved satisfactory recoveries for PAEs at spike levels below 4 μg·L−1, enabling detection of five PAEs including diisodecyl phthalate (DIDP), with improved efficiency via repeated extraction. SPE offered lower detection and quantification limits, higher accuracy and sensitivity, and achieved high recoveries for 12 EDCs and 10 antibiotics at spike levels ≥0.2 μg·L−1, with detection limits as low as 0.1–6.4 ng·L−1. The developed SPE coupled with liquid chromatography-Orbitrap mass spectrometry (LC-Orbitrap MS) method was applied to industrial wastewater samples. Across five industrial sectors (coatings, rubber, pharmaceuticals, inks, and materials technology), five antibiotics and ten EDCs were detected, with total concentrations ranging from 0.03–0.56 μg·L−1 and 0.07–1.91 μg·L−1, respectively. Sector-specific profiles emerged: rubber industry effluent was dominated by dibutyl phthalate (DBP) at 1.07 μg·L−1, while pharmaceutical effluent featured sulfamonomethoxine (SMM) at 0.34 μg·L−1. This systematic evaluation demonstrates that SPE-LC-Orbitrap MS is robust for complex matrices, providing a technical foundation for accurate quantification of emerging contaminants in industrial wastewater.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3808-x
The uncontrollable Zn dendrites and serious parasitic side reactions of the zinc anode severely impede the practical application of aqueous zinc-ion batteries. In this work, a unique strategy of multipoint solvate coordination center is proposed, which anchors Zn2+ and H2O with complex sites to establish an intermolecular connection within the asymmetric solvation structure. A hydrated deep eutectic electrolyte based on multi-site methylurea (MU) with Janus properties is developed, in which Zn2+ and H2O interact with MU through Lewis acid-base and hydrogen bonding interaction, and the regulated asymmetric solvation configuration can guide the (002)-ordered Zn deposition. Simultaneously, a small amount of polyethylene glycol (PEG, Mw=20000) can facilitate homogenous (002) Zn deposition by suppressing Zn2+ transfer kinetics. Benefiting from the rationally regulated solvation structure and PEG molecules adsorbed onto Zn anodes, the side reactions and Zn dendrites are significantly inhibited. As a result, the Zn||Zn symmetric cell delivers outstanding cycling performance over 3900 h (1 mA cm−2, 0.5 mA h cm−2). In addition, the Zn||V2O5 battery maintains 79.2% capacity retention after 1000 cycles at 1 A g−1. The results suggest a promising oriented regulation strategy for sustainable aqueous zinc-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3823-4
The global demand for chlorine gas continues to rise, driven by its indispensable role in chemical synthesis, disinfection, and wastewater treatment. Electrocatalytic chlorine evolution from seawater presents a promising alternative to the energy-intensive chlor-alkali process, yet it is hampered by the competing oxygen evolution reaction and the sluggish kinetics of chlorine evolution on conventional catalysts. Here, we report a novel hollow porous CoNiSe2/NiSe2 heterostructure nanosheet array synthesized via ion exchange and calcination, which exhibits exceptional catalytic activity and selectivity for the chlorine evolution reaction in acidic seawater-like electrolytes. The unique hollow porous morphology provides a high specific surface area, facilitating mass transport and exposing abundant active sites. Crucially, the heterointerface between CoNiSe2 and NiSe2 promotes d-p orbital hybridization between Co/Ni 3d and Se 4p states, which lowers the reaction energy barrier for chlorine evolution. The catalyst achieves a low overpotential of 108 mV to reach a current density of 100 mA cm−2 in 4.0 M NaCl acidic medium, with excellent stability and Cl2 selectivity. This work demonstrates the potential of non-noble metal selenides as efficient and durable catalysts for chlorine production, offering a pathway toward more sustainable chlor-alkali technology.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3840-3
Tactile sensing for dexterous robotic hands is essential for achieving human-like precision in manipulation. However, current tactile sensors face challenges such as insufficient durability, limited coverage, and poor conformability to curved, jointed surfaces. This study presents a stretchable distributed tactile sensor array designed for dexterous robotic hands. The array comprises 18 sensing units distributed across the hand, incorporating quasi-homogeneous functional layers interconnected by crosslinked interpenetrating networks, and composite electrodes combining high conductivity with stretchability. This design yields a thin, soft, transparent, and stretchable sensor array that integrates seamlessly with a commercial dexterous hand. The sensor array exhibits high interlayer tensile strength, high sensitivity, low hysteresis, and excellent long-term reliability over 10,000 loading cycles. Experimental results demonstrate accurate detection of tactile force across the entire robotic hand during object grasping. Using convolutional neural network algorithms, the sensor array identifies different object types with 90.1% accuracy, with results displayed in real time on a digital twin interface. The proposed sensor array holds significant potential for embodied intelligence and robotics in adaptive grasping, safe manipulation, and remote teleoperation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-3961-8
This correction addresses an inadvertent misplacement of Fig. 4b3 during figure reorganization in the original article published in Science China Materials, volume 65, issue 10, 2022, page 2850 (DOI: 10.1007/s40843-022-2024-6). The corrected Fig. 4b is presented herein. The authors confirm that this correction does not affect the results, conclusions, text, or figure caption of the original work. The correction was requested by the authors and received on 6 January 2026, accepted on 8 January 2026, and published online on 10 February 2026. The original study introduced flexible electrostatic hydrogels derived from marine organisms for nitric oxide-enhanced photodynamic therapy against multidrug-resistant bacterial infections. The correction ensures the accurate representation of experimental data, maintaining the integrity of the scientific record.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511041
Hydroxyl radicals (·OH) generated via dark reactions under fluctuating redox conditions significantly influence pollutant degradation and elemental cycling, yet the key electron supply mechanisms driving their sustained production remain unclear. This study aimed to elucidate the electron-driven processes underlying sustained dark ·OH generation in mangrove soils under redox fluctuations. Simulated tidal redox cycles were conducted, and electron donating capacity (EDC), three-dimensional fluorescence spectroscopy, nuclear magnetic resonance, and high-throughput sequencing were employed to analyze the dynamics of different Fe(II) species, key organic matter components, and microbial communities. Results demonstrated that, without exogenous electron donors, mangrove soils exhibited stable ·OH generation potential and EDC. During early redox cycles, total EDC of soil suspensions was dominated by reactive Fe(II), while the contribution of reduced organic matter increased over time, with solid-phase components accounting for 94.5%–97.6% of total EDC. Humic acids in soil organic matter facilitated reversible electron transfer via quinone functional groups, maintaining redox activity. Geothermobacter and Desulfobulbus were identified as dominant iron-reducing bacteria, likely key microorganisms for regenerating the "iron-organic matter" electron sources. This study reveals the mechanisms of endogenous electron donor regeneration and sustained dark ·OH generation mediated by iron and organic matter cycling in mangrove soils, providing theoretical support for understanding the long-term environmental effects of ·OH in tidal environments and its impact on biogeochemical cycles.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3948-7
High-performance thermoelectric materials are typically narrow-band gap semiconductors. Here, by decoupling charge and heat transport in BaZrS3 with a band gap of about 1.9 eV, we made the emerging chalcogenide perovskite a high-performance thermoelectric material with only earth-abundant elements. Our first-principles calculations indicate that the high ionicity of BaZrS3 renders the electrons to propagate mainly through the Zr-4d orbitals, so that isovalent alloying Se on S sites minimally affects its charge transport while effectively suppressing lattice thermal conductivity. Using a flux-assisted solid-state method, we synthesized single-phase BaZrS3(1−x)Se3x samples with 0 ≤ x ≤ 0.25. As an indicator of decoupled charge and heat transport, the electron mobility is found barely degraded with increasing Se content, while the thermal conductivity is significantly reduced from 2.07 to 0.99 W m−1 K−1 at room temperature. This results in a record-high ZT of 0.81 at 750 K, a value never achieved for materials with band gaps greater than 1.5 eV, and the highest among all perovskite materials. Our work not only underscores the potential of wide band gap semiconductors as high-performance thermoelectric materials, but also demonstrates the strategy of decoupling the charge and heat transport for enhancing their thermoelectric performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3962-y
Photochromic Förster resonance energy transfer (pc-FRET)-based subnanometric polymersomes with accurate color control offer a transformative yet challenging tactic for advanced and custom-tailored information encryption. Herein, various amphiphilic alternating pyrene/azobenzene-containing copolymers were polymerized using one-pot Ugi four-component polycondensation. Subsequent self-assembly was performed to produce highly-integrated monolayer subnanometric polymersomes (MSNPSs) and their composites, with diameters of around ~250 nm and vesicular thicknesses of approximately ~12.0 Å. J-aggregated monolayer chain-folding mechanism was accountable for the donor-acceptor-donor stacking manner within the vesicular membrane, beneficial to achieve highly efficient energy transfer. The trans-to-cis photoisomerization of azobenzenes rendered MSNPSs and their composites with photo-triggered structural transitions in diameter and vesicular thickness. Benefitting from considerable spectral overlap between cis-azobenzene and pyrene, MSNPSs and their composites were capable of photo-controllable non-invasive pc-FRET performance with a wide Stokes shift (~320 nm). The accurate color variation from blue to red highly depended upon precise modulation of both irradiation duration and precursor-fixed donor/acceptor ratios. The proof-of-concept individually multichromatic 2D QR code was attained using photochromic MSNPSs and their composites in patterning lithography, displaying a multimodal decryption and favorable repeatability for high-level and personalized information protection. Our work paves a prospective avenue to meticulously craft stimuli-chromatic polymersomes for the potential of advanced information encryption.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3921-2
Moisture-enabled energy harvesting technologies offer a promising route for self-powered strain sensing, yet conventional generators suffer from slow response, poor recovery, and limited multidirectional resolution. Here, we report a stretchable thermoplastic polyurethane (TPU) nanofiber moisture-enabled electric generator (MEG) with highly aligned ion channels. A carbon black/sodium dodecylbenzene sulfonate (CB/SDBS) layer is coated on the TPU membrane, while carboxymethyl cellulose (CMC) and acidified poly(sodium 4-styrenesulfonate) (HPSS) are applied on opposite sides, establishing lateral hydrophilicity and ion gradients to drive directional ion migration. The planar MEG is lightweight, flexible, and requires no fully covered electrodes, enabling conformity to complex deformations. The aligned channels reduce ion migration tortuosity, enhancing ion transport efficiency and flux. As a result, the aligned MEG (ATMEG) delivers 0.2 V and 0.51 μA cm−2 at ~90% relative humidity, corresponding to 400% and 287% enhancements compared with the unaligned MEG (UATMEG). The ATMEG also exhibits ultrafast response (0.16 s) and recovery (0.08 s). Utilizing its anisotropic characteristics, a multidirectional self-powered strain sensor is developed, capable of distinguishing both the amplitude and direction of human motion, demonstrating strong potential for adaptive wearable electronics and intelligent motion monitoring.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511054
A novel S-scheme heterojunction photocatalyst, Bi6O5(OH)3(NO3)5·3H2O/BiOBr0.8I0.2 (BON@BI), was synthesized via a one-step hydrothermal method using Bi6O5(OH)3(NO3)5·3H2O (BON), KBr, and KI as precursors. The mass ratio of BON to BiOBr0.8I0.2 (BI) was optimized, revealing that the 20% BON@BI composite (BON@BIOPT) exhibited the highest visible-light photocatalytic activity. Under 30 min of visible-light irradiation, BON@BIOPT achieved a 99.8% degradation efficiency of Rhodamine B (RhB), approximately twice that of pristine BI (52.2%). The composite displayed a rod-like morphology with uniform nanosheets, and its specific surface area increased from 32.54 m²·g⁻¹ (BI) to 44.7 m²·g⁻¹. The absorption edge red-shifted from 560 nm (BI) to 580 nm, narrowing the bandgap from 2.55 eV to 2.43 eV. The S-scheme heterojunction formed between BON and BI generates an internal electric field that effectively suppresses recombination of strongly reducing photogenerated electrons and strongly oxidizing holes, with superoxide radicals (O₂•⁻) and holes (h⁺) identified as the primary reactive species. BON@BIOPT exhibited excellent stability, retaining 88.6% degradation efficiency after seven consecutive cycles. It also demonstrated robust environmental adaptability, maintaining 85–98% degradation efficiency under various pH conditions and in the presence of interfering anions. The degradation pathway of RhB involves N-de-ethylation, cleavage of the conjugated chromophore, and deamination, ultimately mineralizing into low-molecular-weight organics, inorganic salts, CO₂, and H₂O. These results underscore the potential of BON@BIOPT for practical remediation of organic pollutants in water.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60656-1
Under the carbon neutrality strategy, biomass boilers have emerged as key facilities for renewable energy utilization, yet are characterized by low-concentration SO2 emissions. Ca-based dry desulfurization presents a promising technology for biomass boiler flue gas purification due to its compact structure, low capital investment and simple operation and maintenance. However, it is generally limited by the low adsorbent utilization and insufficient desulfurization efficiency. Herein, this study developed a novel Ca-Mn composite adsorbent through a synergistic strategy integrating F127 surfactant to optimize dispersion and Mn loading to enhance oxidation efficiency. The resulting adsorbent not only significantly increased the breakthrough sulfur capacity of the Ca-based material but also markedly improved the synergistic removal of Hg0. It was demonstrated that the introduction of Mn elements and F127 effectively suppressed the agglomeration of Ca(OH)2 crystallites and induced an oxygen vacancy-rich structure, while simultaneously optimizing the pore structure of the adsorbent. The modified adsorbent exhibited the enlarged specific surface area and pore volume, which favored to enhance the reaction mass transfer and effectively prevent the pore blockage and coverage of active sites by desulfurization products. The Mn sites and oxygen vacancies formed catalytic centers, which not only accelerated the desulfurization reaction by promoting SO2 oxidation but also enabled the adsorbent to couple with Hg0 catalytic oxidation functionality. Consequently, the simultaneous removal of SO2 and Hg0 was significantly enhanced on the Ca-Mn composite adsorbent.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4017-y
Lattice distortion via entropy engineering can significantly optimize thermoelectric performance by intensifying phonon scattering. However, excessive lattice distortion in high-entropy materials inevitably hinders carrier transport, limiting the wide-temperature average ZT (ZTave). To enhance the wide-temperature thermoelectric performance of low-cost PbS-based compounds, this work introduces moderate lattice distortion by controlling entropy around 1.0R (R is the gas constant) to balance phonon and carrier transport, alleviating restrictions on carrier mobility. Substantial Se and Te alloying in PbS induces rock-salt lattice distortion, effectively impeding phonon propagation, thus suppressing lattice thermal conductivity (κlat) from 2.41 W m−1 K−1 in PbS to 0.66 W m−1 K−1 in PbS0.5Se0.35Te0.15 at 300 K. Additionally, Cu interstitials are introduced into the lattice-distorted PbS0.5Se0.35Te0.15 to further optimize carrier density and weighted carrier mobility (μW), leading to significant improvement in μW/κlat parameter at 300–773 K. Finally, a room-temperature ZT of 0.53 and a maximum ZT of 1.44 are obtained in PbS0.5Se0.35Te0.15-1%Cu sample, contributing to an impressive ZTave of 1.08 at 300–773 K and a maximum power generation efficiency (ηmax) of 7.5%. The results outperform previously reported cost-effective PbS-based compounds and highlight the importance of lattice distortion regulation in enhancing wide-temperature thermoelectric performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4099-2
Lithium (Li)-metal batteries (LMBs) are promising next-generation energy storage systems due to their high theoretical capacity (3860 mAh g−1) and low electrochemical potential (−3.04 V vs. standard hydrogen electrode). However, uncontrollable Li dendrite growth and volume fluctuations during cycling cause low Coulombic efficiency, safety hazards, and rapid capacity decay. Conventional 3D current collectors mitigate these issues by increasing surface area and providing void space, but they suffer from top-heavy deposition and underutilization of internal space. Emerging Janus/gradient anode structures, featuring asymmetric or gradient properties in lithiophilicity, conductivity, or porosity, enable bottom-up Li plating and efficient space utilization. This review systematically summarizes design principles, operational mechanisms, and recent progress in lithiophilic-lithiophobic Janus designs, conductivity-gradient frameworks, and dual-gradient configurations. These structures collectively improve Coulombic efficiency, cyclic longevity, and safety. The review concludes with future research directions, underscoring the potential of Janus/gradient anodes for high-energy-density and durable LMBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4132-y
Manganese-iron-based mixed polyanionic cathodes are promising for sodium-ion batteries (SIBs) due to high energy density and operating voltage, but suffer from Jahn-Teller distortion of Mn3+ that degrades cycling stability. Here, a structural modulation strategy via Mg2+ doping is reported. Electrochemically inert Mg2+ forms stronger chemical bonds, adjusts lattice parameters, and suppresses Jahn-Teller distortion, enhancing structural stability. Mg2+ also widens sodium-ion diffusion channels, improving diffusion kinetics. Additionally, an in-situ three-dimensional carbon nanotube (CNT) conductive network boosts electronic conductivity. The resulting NFMPP-Mg@CNTs cathode delivers a discharge capacity of 126 mAh g−1 at 0.1 C (near theoretical 129 mAh g−1), retains 80% capacity after 3000 cycles at 0.5 C, and achieves an energy density of 401 Wh kg−1, among the highest reported for mixed phosphate systems. Ex-situ XPS and first-principles calculations confirm that Mg2+ resists geometric distortion by enhancing lattice stability and widening Na+ diffusion pathways (migration barrier reduced from 0.566 to 0.398 eV). This work provides a viable route for high-energy, long-life SIB cathodes suitable for large-scale energy storage.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4026-0
Copper-based synergistic therapy integrating chemodynamic therapy (CDT) and cuproptosis holds promise for tumor treatment but faces clinical translation hurdles including long-term toxicity, low catalytic efficiency, off-target effects, and copper ion efflux. Here, we developed metabolizable ultrasmall benzothiazole-based covalent organic framework nanodots (COF NDs) via click condensation followed by liquid exfoliation. The dense donor-acceptor configurations confer a high photothermal conversion efficiency of 51.16%, while bisthiazole motifs enable specific Cu2+/Cu+ chelation (0.56:0.44), facile PEGylation, and mitochondrial targeting. These features enhance physiological stability and enable tumor-specific photothermal-catalytic synergy. Mitochondrial accumulation elevates intracellular copper to a critical threshold, inducing cuproptosis and suppressing tumor growth and metastasis. The NDs are efficiently excreted via renal and fecal pathways, demonstrating favorable biocompatibility and clinical potential as copper-based nanotherapeutics.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3587-4
Unstable zinc interfaces arising from dendrite growth and parasitic reactions impede the practical deployment of rechargeable aqueous zinc-ion batteries. This study introduces 1-(2-pyridylazo)-2-naphthol (PAN) as a parts-per-million (ppm) level electrolyte additive to stabilize the Zn anode. Theoretical and experimental analyses reveal that PAN undergoes parallel adsorption on the Zn surface, establishing strong π-π interactions between adjacent molecules that efficiently repel water. The OH, pyridine N, and azo N groups in PAN chelate Zn2+, modulating Zn2+ diffusion and promoting uniform deposition while suppressing dendrite formation. A 10 ppm (0.04 mM) PAN addition extends the lifespan of a symmetrical cell to 1500 h at 2 mA cm−2 and 1 mAh cm−2. The Zn||Cu half-cell achieves a Coulombic efficiency of 99.91% over 3500 cycles at 5 mA cm−2 and 1 mAh cm−2. Full cells with NH4V4O10 and MnO2 cathodes exhibit enhanced cycling stability. Notably, a Zn||NH4V4O10 pouch cell retains 71.1% capacity after 250 cycles at 0.8 A g−1. This work demonstrates a viable strategy for selecting high-efficiency additives for aqueous metal-based batteries.