SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4248-2
Marine biofouling imposes substantial operational penalties on maritime assets, yet commercial silicone foul-release coatings rely on static, non-adaptive networks that cannot be reprocessed or repaired. This work introduces selenonium-salt-catalyzed dynamic siloxane exchange as a route to polydimethylsiloxane (PDMS) vitrimer coatings. The authors incorporate A16Se+ organoselenium catalysts into PDMS networks at loadings designated A16Se+xPDMS, enabling thermally activated siloxane bond exchange that confers vitrimeric stress relaxation, reprocessability, and high-temperature self-healing. Antibiofouling performance is benchmarked against pristine PDMS using colony morphology assays for Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa, SEM imaging of bacterial adhesion after 3 h, Chlorella fluorescence adhesion quantification, zeta potential measurements, and 3-month seawater immersion panels. Reviewer 1 questioned the direct relevance of recyclability and high-temperature self-healing to marine antifouling and requested that surface elastic modulus and Pseudomonas antibacterial data be elevated to the main text. In response, the authors relocated scratch and self-healing results from Figure 5 to Supporting Information Figures S12 and S13, condensed the main-text discussion, and integrated surface elastic modulus data into Figure 4G and Pseudomonas antibacterial results into Figure 6A. The revised manuscript positions dynamic exchange as supporting evidence of network dynamics rather than as a primary antifouling metric, while foregrounding modulus and antibacterial performance as the application-relevant properties.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4476-1
Self-sustained oscillation in soft actuators enables autonomous, untethered robotic locomotion, yet existing light-driven systems suffer from low oscillation frequencies, rapid photothermal degradation, and reliance on external controllers. This work presents a bat-inspired soft robot that converts continuous near-infrared (NIR) irradiation into sustained rotational motion via a coiled MXene-based liquid crystal elastomer (LCE) actuator. The actuator integrates Ti3C2Tx MXene nanosheets as photothermal converters within an LCE matrix, achieving a photothermal conversion efficiency of 78.3% and a steady-state temperature of 142 °C under 1.5 W cm−2 NIR (808 nm). The coil geometry induces a self-shadowing effect that generates periodic light exposure, producing autonomous oscillation at 2.7 Hz with an amplitude of 45°. The robot demonstrates a rotational speed of 120 rpm and a specific power density of 3.2 W kg−1, outperforming previously reported light-driven oscillators by a factor of 2.5. Under continuous operation for 10,000 cycles, the actuator retains 92% of its initial oscillation amplitude, with a degradation rate of 0.008% per cycle. The bat-inspired wing morphology enables directional rotation and obstacle avoidance in confined spaces. This platform eliminates the need for external modulation, offering a scalable route to autonomous soft robotics for inspection, environmental monitoring, and micro-manipulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4490-y
The development of efficient enzyme mimics for CO2 hydration remains a critical challenge for industrial carbon capture. This study reports a bioinspired three-dimensional Zn-coordinated organic framework (Zn-SOF) synthesized via solvothermal assembly of a salen-based ligand with zinc ions. The resulting material exhibits a carbonic anhydrase-like active site with a Zn-N2O2 coordination environment, as confirmed by X-ray absorption spectroscopy. The Zn-SOF demonstrates a CO2 hydration rate of 3.2 × 10^-3 s^-1 per active site, representing a 12-fold enhancement over the homogeneous Zn-salen complex and approaching 8% of native carbonic anhydrase II activity. The catalyst maintains structural integrity over 10 consecutive cycles with <5% activity loss and operates optimally at 25–40 °C and pH 7.4–9.0. Kinetic analysis reveals a Michaelis-Menten constant (Km) of 28 mM for CO2 and a turnover number (kcat) of 4.1 s^-1, outperforming benchmark Zn-based mimics. The framework's hierarchical porosity (BET surface area: 620 m2 g^-1) facilitates substrate diffusion, while the hydrophobic pore environment enhances CO2 affinity. This work establishes a design paradigm for robust, recyclable enzyme mimics that bridge the gap between homogeneous catalysts and natural enzymes, offering a scalable route for post-combustion CO2 capture.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4316-0
The rapid development of small molecule acceptors (SMAs) has enabled organic photovoltaics (OPVs) to achieve power conversion efficiencies exceeding 21%. Structural asymmetry has emerged as a particularly effective approach for boosting acceptor performance. This review provides a comprehensive overview of asymmetric SMAs from the molecular scale to the nanoscale and macroscale. The main text is organized into four sections: molecular design strategies for structural asymmetry, crystal structure evolution from symmetry breaking, morphological characteristics revealed by advanced characterization techniques, and energy loss mechanisms involving asymmetric SMAs. At the molecular scale, asymmetry enables precise modulation of dipole moments and intermolecular interactions, directly affecting crystalline packing and charge-transport networks. At the nanoscale, it further regulates domain purity, phase continuity, and molecular orientation. Asymmetric designs can also help mitigate non-radiative voltage loss through modulation of charge-transfer state energetics. Overall, asymmetric molecular design introduces additional structural and electronic tunability, offering new opportunities for overcoming the trade-offs that limit OPV performance. Finally, we discuss ongoing challenges and outline future perspectives to guide continued development and innovation in asymmetric SMA design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4443-5
The accelerating pace of urbanization and rising global temperatures have transformed reliable cooling from a luxury into a fundamental necessity for human health and economic activity. With urban populations projected to reach 66% of the global total by 2050, the energy demand for air conditioning is expected to increase by 750%. Conventional vapor-compression cooling is highly energy-intensive, accounting for approximately 17% of global electricity consumption while contributing to carbon emissions, refrigerant-related environmental concerns, and urban heat accumulation. Passive radiative cooling has emerged as a promising alternative because it dissipates heat to outer space through the atmospheric window (8–13 μm) without electricity or moving parts, offering an energy-efficient and environmentally sustainable cooling strategy. Despite its promise, effective daytime radiative cooling requires maximizing solar reflectance to minimize heat gain from solar absorption. Consequently, most radiative cooling materials appear white or silver. In recent years, researchers have proposed several strategies to overcome this aesthetic limitation. The most straightforward approach is to incorporate dyes or fluorescent pigments. Both mechanisms inevitably rely on optical absorption, resulting in parasitic heat generation that compromises cooling performance. In contrast, structural colors arise from wavelength-selective light interference or scattering by micro- or nanostructures with feature sizes comparable to the wavelength of visible light, enabling vivid coloration with minimal intrinsic absorption. Representative mechanisms include thin-film interference, diffraction gratings, and photonic crystals. Nevertheless, existing structurally colored radiative cooling materials usually require multi-step fabrication processes and specialized instruments, making large-scale production costly and time-consuming. Recently, Liu et al. reported a bilayer, colored ethyl cellulose (BCEC) coating produced in a single casting step, which significantly simplifies the fabrication process and presents a viable strategy for the practical deployment of this technology. The fabrication of BCEC involves the drying of an ethyl cellulose (EC)/N,N-dimethylformamide (DMF) solution in a water vapor environment. This induces non-solvent-induced phase separation (NIPS), driven by interactions between solute and solvent molecules. The bilayer structure forms spontaneously in a single step during the drying process: a relatively dense top surface is generated first as the DMF evaporates, after which water vapor diffuses slowly across this skin layer, initiating the NIPS process and producing the porous bottom layer. The dense top layer has a thickness of several hundred nanometers—an ideal scale for generating colors through thin-film interference. More importantly, this thickness can be conveniently and precisely tuned by adjusting the concentration of the precursor solution, making it possible to create various structural colors, including blue, yellow, red, pink, and green. In addition to thickness-dependent color tuning, the BCEC coating also exhibits angle-dependent coloration (iridescence), an intrinsic characteristic of thin-film interference, whereby the reflected peak wavelength shifts with the viewing or illumination angle. The highly porous bottom layer is responsible for the high solar reflectance, resulting from the strong scattering of light by the abundant micro- and nano-pores. The solar reflectance varies slightly with the thickness of the BCEC film; the thickest film (BCEC-5, green film) exhibits the highest solar reflectance of 0.97. Simultaneously, the intrinsic absorption derived from molecular bond vibrations, especially the C–O bond, contributes to the high the
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3660-5
High-sensitivity piezoelectric ceramics with high piezoelectric constants (d33) are crucial for miniaturized, low-power, and high-efficiency transducers. However, conventional performance enhancement relies on intrinsic parameter modulation, which is limited and blind. This study introduces a performance-driven metamaterials creation model to develop structure-function-integrated piezoelectric materials. We systematically investigated the effects of metastructure design on d33 across two-dimensional straight rod (SR) structures, three-dimensional dot-matrix (Octa) structures, complex triply periodic minimal surface (TPMS) structures, and hybrid Octa&SR structures. The results demonstrate that metastructures combining high polarization charge conversion efficiency with low compression modulus (stiffness) effectively enhance d33. The SR structure exhibited optimal polarization charge conversion, the Fks-Shellular (FksS) structure within TPMS showed low stiffness, and the Octa&SR structure combined both properties. Notably, all three structures displayed exceptional piezoelectric performance. Specifically, the FksS structure achieved a substantial d33 of 194 pC/N, a 24% enhancement over conventional solid BaTiO3, while maintaining isotropic and stress-insensitive properties. This work elucidates the mechanism for designing piezoelectric metastructures, offering a novel pathway for developing high-performance, high-failure-strength piezoelectric materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3539-5
MXene-based layered films are promising for electromagnetic interference (EMI) shielding, yet achieving highly ordered structures in scalable production remains challenging. Here, we report a facile centrifugal casting method for fabricating MXene/polyvinyl alcohol (MXene/PVA) films with highly oriented and compact layered structures. During centrifugal casting, the viscous fluid experiences strong shear and centrifugal forces along tangential and normal directions, respectively, inducing compact and oriented arrangement of MXene nanosheets. Consequently, the Herman's orientation factor increases from 0.681 to 0.794 as rotation rate rises from 0 to 4000 r/min. Accordingly, tensile strength and toughness improve from 55.2 to 191.1 MPa and from ~0.8 to 2.5 MJ/m³, respectively. The highly oriented and compact layered structure with ultrathin thickness (~8 μm) enables a high absolute electromagnetic shielding effectiveness (SSE/t) of 21029 dB cm²/g. Moreover, increased orientation reduces infrared emissivity to 0.248, endowing the film with excellent thermal camouflage capability. This work presents an effective strategy for constructing high-performance MXene-based layered films.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3605-0
Nickel oxide (NiOx) is widely used as a hole transport material in inverted perovskite solar cells (PSCs). However, its practical application is limited by low intrinsic conductivity and insufficient hole extraction ability, leading to significant interfacial defects that reduce device efficiency and stability. To overcome these issues, two isomeric small organic molecules, 2,6-NOT and 1,5-NOT, were developed and introduced to modify NiOx. These isomers share the same structure but differ in the substitution positions of functional groups, resulting in distinct molecular planarity. Experimental results demonstrate that 1,5-NOT, featuring extended conjugation and enhanced planarity, more effectively enhances the hole extraction/transport capabilities and conductivity of NiOx compared to 2,6-NOT. The NiOx/1,5-NOT-based device achieves a remarkable power conversion efficiency (PCE) of 24.20%, along with excellent long-term stability, surpassing the NiOx control device (18.12%) and the 2,6-NOT-based device (21.87%). These findings indicate that modifying NiOx with small organic molecules significantly improves charge transport performance, and increasing molecular planarity is particularly beneficial for enhancing hole transport and reducing defect density, thereby increasing both efficiency and stability. This work provides a new strategy for NiOx modification via small organic molecules, offering a promising route to high-performance inverted PSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3647-4
Chromium oxides (CrOx) and fluorinated graphite (CFx) are two typical cathode materials for lithium primary batteries. The former possesses the highest theoretical energy density but suffers from low practical capacity and inferior rate capability; the latter has the highest theoretical discharge capacity but fails to support fast discharge. Combining the merits of both cathodes via a composite design is desirable, yet the electrochemical performance of such composites remains unsatisfactory. In this work, we identified that by regulating the overlapped discharge potential of these two cathodes, fluorine atoms migrate from CFx to CrOx, leading to a homogeneous distribution of LiF and improved ionic and electronic conductivity, ultimately enhancing high-rate discharge performance. Benefiting from this synergetic effect, the CrOx/10%eCFx composite exhibits a considerably high energy density of 496.59 Wh kg−1 at a power density of 49.7 kW kg−1 (50 C), far superior to pure CrOx and CFx electrodes. We believe that the high-performance CrOx/eCFx composite cathode will justify its practical application in revitalizing advanced lithium primary batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3919-0
Nuclear energy is critical for sustainable economic development and achieving carbon neutrality. With only about 6.14 million tons of terrestrial uranium, sufficient for ~70 years of global nuclear power plant operation, the recovery of uranium from seawater and spent fuel is essential for long-term nuclear fuel supply. The ocean contains approximately 4.5 billion tons of uranium, which could sustain nuclear power for ~2000 years if efficiently extracted. However, seawater uranium extraction faces significant challenges due to the extremely low uranium concentration (~3.3 ppb), high concentrations of competing ions, natural organic matter, and marine biofouling. This perspective reviews representative laboratory advances, including sulfonated covalent organic frameworks (S-COF) achieving a sorption capacity of 31.5 mg/(g·day) with high selectivity, amidoxime-based organic cages with a capacity of 11.97 mg/g over 30 days, and a micro-redox reactor strategy that continuously regenerates binding sites. Electrochemical methods have also shown promise for converting soluble U(VI) to insoluble U(IV) oxides. Despite these advances, the transition from laboratory powders to durable marine materials remains problematic. Key gaps include the need for antibacterial properties, mechanical stability under wave action, cost competitiveness with terrestrial mining, and environmental safety of nanomaterials. Artificial intelligence (AI) is proposed to accelerate the design of high-performance, stable materials. This perspective emphasizes the necessity for interdisciplinary research to bridge the gap between bench-scale innovations and practical ocean deployment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3451-2
Visual aesthetics is a key metric of semi-transparent organic photovoltaics (ST-OPVs) for building-integrated solar windows, yet previous studies have primarily focused on the compromise between efficiency and transparency. This work addresses the overlooked aspect of full visual aesthetic control, particularly the bidirectional reflected color for architectural harmony, via designing ST-OPVs with double-sided ultra-thin Ag/TeO2 transparent electrodes. This design facilitates full-spectrum color tunability covering the whole standard color gamut of CIE coordinates on both surfaces, achieved simply by adjusting layer thicknesses. The resulting devices exhibit neutral transparency (16.6%–27.0% average visible transmittance) and competitive power conversion efficiencies (8.1%–9.2%). Additionally, the devices demonstrate strong flexibility, with flexibility-adaptive coloration and curvature-enhanced aesthetics. This work presents an ST-OPV design featuring full visual aesthetics and considerable performance, paving the way for commercialization of organic solar windows for building and vehicle integration.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3899-9
Metal halide hybrids have emerged as a highly promising class of optoelectronic materials owing to their rich chemical and electronic diversity, high luminescence efficiency, and tunable photophysical properties. Incorporating chirality into these systems imparts pronounced circularly polarized luminescence (CPL) activity, creating new opportunities for advanced smart optoelectronic and spintronic applications. Although numerous reviews have been dedicated to CPL-active perovskites, their non-perovskite ionic counterparts have yet to be systematically and comprehensively reviewed. Given the rapid advancements in this burgeoning field, such a work is both timely and crucial to chart its future course. This review summarizes recent progress in non-perovskite ionic metal halide hybrids exhibiting CPL emission, highlighting four aspects: (1) the intrinsic correlations among different characterization techniques; (2) the strategic advantages of these materials for CPL applications; (3) methodologies for enhancing their CPL performance; (4) the prerequisites and mechanisms underlying CPL generation in achiral metal halide hybrids. Finally, we discuss their emerging applications in light-emitting devices, information encryption, anti-counterfeiting technologies, and scintillators, and provide perspectives on the remaining challenges and future directions in this rapidly evolving field.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510004
Ammonium salt crystallization-induced blockage of the regenerative heat exchanger in regenerative thermal oxidizers (RTOs) remains a critical operational challenge, particularly in pharmaceutical applications where NH4Cl constitutes up to 70% of the fouling deposits. This study employs computational fluid dynamics (CFD) to systematically simulate six purging configurations, varying injection angle and pipe arrangement, and quantifies purging effectiveness via a novel evaluation method based on characteristic observation planes. Using the Realizable k-ε turbulence model coupled with a porous media model, we analyze the velocity distribution and low-velocity failure zones at the gas chamber–regenerator interface. Results demonstrate that a single-pipe 45° oblique injection achieves the highest effective purging area of 57.6%, a 35.7% improvement over conventional horizontal purging. Increasing pipe diameter significantly enhances flow uniformity, yielding an efficiency gain of approximately 40%, outperforming mere increases in gas velocity. A synergistic optimization strategy is proposed, prioritizing high-performance purging structures with coordinated parameter tuning. The recommended configuration—single-pipe 45° injection, 280 mm pipe diameter, and 14 m·s−1 gas velocity—achieves 88.2% purging efficiency without additional fan power, representing a 45.6% improvement over conventional modes. These findings provide a theoretical basis and engineering solution for RTO purging system design and operational optimization.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025011002
Cadmium (Cd) contamination in farmland soils poses a threat to food security, necessitating effective remediation strategies. This study prepared three types of phosphorus-enriched biochar (PBC) from rice straw and different phosphorus sources (fused calcium magnesium phosphate, citric acid-activated fused calcium magnesium phosphate, and monocalcium phosphate) to evaluate their potential in stabilizing Cd(II), releasing phosphorus, and enhancing plant resistance to heavy metal stress. Under Cd stress, PBC amendments significantly improved soil physicochemical properties and reduced Cd bioavailability through direct immobilization (adsorption, precipitation) and indirect mechanisms. Specifically, CBC and MBC treatments reduced DTPA-extractable Cd by 45.73% and 48.92%, respectively. The porous structure of biochar facilitated sustained phosphorus release, influencing soil solution phosphorus dynamics. In pot experiments with Brassica napus L., PBC application significantly improved agronomic traits and reduced oxidative stress markers. The C5 treatment increased leaf area by 100%, M7 increased plant height by 26.8%, and M3 reduced malondialdehyde (MDA) and hydrogen peroxide (H2O2) contents by 72.5% and 61.2%, respectively. These findings demonstrate that PBC effectively alleviates Cd toxicity, promotes plant growth, and enhances stress resistance, offering a feasible strategy for remediating Cd-contaminated soils while providing a sustainable phosphorus source.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606021
To provide a theoretical basis for energy-saving combustion of regenerative thermal oxidizers (RTOs), this study analyzes energy nodes during RTO operation, refines heat balance accounting, and establishes an overall energy system. Taking a three-chamber RTO as the research object, the enthalpy of exhaust gas at different stages is calculated, and a whole-process heat balance model is developed to systematically analyze exhaust gas preheating, combustion, heat recovery, and heat loss transfer. An improved energy accounting method is proposed to address dynamic heat exchange inside heat accumulators, coupling of multiple gas streams, and boundary heat loss under complex conditions. The longitudinal temperature distribution function of heat accumulators is introduced to overcome difficulties in heat accounting within the accumulator chamber. A thermodynamic system covering 11 key internal energy nodes is constructed. Combined with design characteristics of RTO operation across industries, the application scope of the overall energy system is analyzed; equilibrium terms can be adjusted according to actual conditions, ensuring wide applicability. Validation via an RTO energy system for a glove manufacturing plant demonstrates that outlet temperature prediction accuracy improves from 14.3% to 2.8%, providing a theoretical foundation for future intelligent energy-saving combustion research.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3898-7
Platinum (Pt) is the benchmark catalyst for the hydrogen evolution reaction (HER) and hydrogen oxidation reaction (HOR) in acidic electrolytes, but its performance in alkaline media is limited by excessively strong hydrogen binding energy (HBE). Here, we report oxygen-modified ultrasmall RuCu nanocrystals (RuCu/C-200) as an efficient catalyst for both alkaline HER and HOR. The RuCu/C-200 catalyst exhibits excellent HER activity with an overpotential of 9 mV at 10 mA cm−2 and a Tafel slope of 19.7 mV dec−1. For HOR, it achieves a 4.2-fold higher exchange current density than the unannealed sample. Mechanistic studies reveal that the optimized HBE, hydroxyl binding energy (OHBE), and strongly hydrogen-bonded interfacial water, induced by oxygen modification, are the intrinsic determinants of the improved catalytic activity. This work underscores the potential of combining nanoscale structural design with oxygen modification to develop high-performance Ru-based electrocatalysts for both alkaline HER and HOR.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3808-x
The uncontrollable Zn dendrites and serious parasitic side reactions of the zinc anode severely impede the practical application of aqueous zinc-ion batteries. In this work, a unique strategy of multipoint solvate coordination center is proposed, which anchors Zn2+ and H2O with complex sites to establish an intermolecular connection within the asymmetric solvation structure. A hydrated deep eutectic electrolyte based on multi-site methylurea (MU) with Janus properties is developed, in which Zn2+ and H2O interact with MU through Lewis acid-base and hydrogen bonding interaction, and the regulated asymmetric solvation configuration can guide the (002)-ordered Zn deposition. Simultaneously, a small amount of polyethylene glycol (PEG, Mw=20000) can facilitate homogenous (002) Zn deposition by suppressing Zn2+ transfer kinetics. Benefiting from the rationally regulated solvation structure and PEG molecules adsorbed onto Zn anodes, the side reactions and Zn dendrites are significantly inhibited. As a result, the Zn||Zn symmetric cell delivers outstanding cycling performance over 3900 h (1 mA cm−2, 0.5 mA h cm−2). In addition, the Zn||V2O5 battery maintains 79.2% capacity retention after 1000 cycles at 1 A g−1. The results suggest a promising oriented regulation strategy for sustainable aqueous zinc-ion batteries.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3787-x
Circumventing the tumor's defensive antioxidant system and achieving precision cancer therapy remain major challenges in high-efficacy tumor treatments. Here, we propose a synergistic strategy integrating non-oxidative physical ablation and oxidative chemical intervention. An acid-responsive self-collapsing nanomineral PCSB is constructed, comprising poly(acrylic acid)-modified calcium sulfite (CaSO3) and a pH-responsive photoacoustic (PA) therapeutic molecule, aza-BDP. In the tumor acidic microenvironment, PCSB decomposes, releasing PA agents and SO2/Ca2+, thereby enabling combined non-oxidative mechanical damage from PA therapy and oxidative chemical damage from SO2 gas and Ca2+ ions. This dual-action approach effectively reduces resistance conferred by tumor antioxidant mechanisms and improves treatment precision. The study presents a synergistic physical-chemical strategy with significant potential for solid tumor elimination.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3852-9
Lithium-ion batteries (LIBs) with high energy density are essential for electric vehicles and energy storage, but their adoption is hindered by safety and longevity trade-offs. Electrolyte engineering is critical to address these challenges. Weakly solvating electrolytes enhance anode interphase stability and safety by promoting ion association and reducing flammable solvents, yet they exacerbate thermal runaway due to ion association lowering the energy barrier for exothermic anion decomposition. Lu and coworkers demonstrated that pronounced ion association reduces the onset temperature of exothermic reactions by approximately 94 °C across over 20 electrolyte systems. To mitigate this, a solvent-relay strategy was developed: a temperature-sensitive 'passing solvent' promotes ion association at ambient temperature, forming a robust SEI and enhancing cycle life, while a temperature-insensitive 'receiving solvent' accepts Li+ at elevated temperatures, promoting dissociation and suppressing exothermic reactions. This design was validated in a 4.5-V graphite-NCM811 pouch cell (1.1 Ah), which delivered 1,000 cycles at 0.45 C, retaining ~81.9% capacity over 4,100 hours. The solvent-relay approach decouples SEI formation from thermal stability, offering a pathway to safe, long-life high-energy LIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3980-y
Organic solar cells (OSCs) have achieved power conversion efficiencies (PCEs) exceeding 20% in laboratory-scale devices, yet challenges persist in developing cost-effective charge-transporting materials (CTMs) that ensure high performance and long-term stability. Conventional organic CTMs such as PEDOT:PSS and PDINN suffer from thermal instability due to molecular diffusion and phase segregation. Solution-processed metal oxides (MOs) offer excellent stability and cost-effectiveness but are plagued by surface defects, particularly hydroxyl groups, which act as recombination centers and photocatalytic sites, degrading device interfaces. Here, we develop an organic-inorganic hybrid strategy to homogeneously passivate solution-processible semiconducting MOs. By first synthesizing MOs rich in surface hydroxyl groups and then introducing organic molecules, we achieve chemically homogeneous passivation that mitigates surface defects. This approach enables favorable interfacial energy level alignment, enhanced charge extraction, and tunable surface energy. Employing these passivated MOs as electron transport layers (ZnO) and hole transport layers (NiOx), we achieve a champion PCE of 20.22% for all-MO CTM-based OSCs, the highest reported to date. Scalability is demonstrated via ambient blade-coating, yielding 18.33% PCE for large-area cells (1.44 cm2) and 16.03% for modules (20.05 cm2), with material costs estimated at only 4% of organic counterparts. Furthermore, devices exhibit outstanding stability, retaining over 80% of initial PCE after 1300 h of maximum power point tracking and over 1000 h of thermal annealing at 85°C. This work establishes a new benchmark for cost-effective, high-performance organic photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3922-2
Photocatalytic reduction of CO2 to syngas (CO and H2) is pivotal for Fischer-Tropsch synthesis and carbon neutrality, yet suffers from rapid charge carrier recombination. Here, we report a solvent-induced defect engineering strategy to fabricate nitrogen vacancy (Nv)-modified Fe3O4 (Fe3O4-Nv-12h). Under visible light (λ ≥ 420 nm), Fe3O4-Nv-12h achieves a total syngas production rate of 43.55 mmol g−1 h−1 with a near 1:1 CO/H2 ratio, representing an 805.2-fold enhancement over pristine Fe3O4 and surpassing state-of-the-art systems. Electron paramagnetic resonance (EPR) and X-ray photoelectron spectroscopy (XPS) confirm that Nv introduction modulates the electronic structure, acting as electron traps to suppress recombination and enhance charge transport. In situ Fourier transform infrared (FTIR) spectroscopy identifies *COOH and *CO as key intermediates for CO formation. This work establishes an effective nitrogen vacancy modification strategy for efficient photocatalytic CO2 conversion to syngas, offering new avenues for high-performance catalyst design.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3971-6
Photocatalytic reduction of soluble U(VI) to insoluble U(IV) is a pivotal technology for uranium remediation and resource recovery. However, conventional covalent organic frameworks (COFs) suffer from short-range electron transport, leading to rapid electron-hole recombination and limited efficiency. Here, we report the rational design of anthraquinone-based COFs with donor-acceptor (D-A) architectures, employing 2,4,6-triformylphloroglucinol (TP) as the donor and 1,4-diaminoanthraquinone (1,4-DQ) or 1,5-diaminoanthraquinone (1,5-DQ) as the acceptor. By varying the connection mode of the building units, the electron transfer distance is systematically extended, effectively suppressing charge recombination. Among the synthesized COFs, ECUT-COF-152 exhibits optimal photocatalytic activity under visible light, achieving 100% U(VI) removal with a maximum reduction capacity of 1950 mg g−1. This work demonstrates that precise tuning of the D-A structure and electron transfer pathways is an effective strategy to enhance the photocatalytic performance of COFs for uranium reduction, offering insights for the design of efficient materials for nuclear waste treatment.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025050801
Oil-contaminated water poses severe ecological and public health risks, yet conventional treatment technologies are hindered by complex processing and low selectivity. Metal-organic frameworks (MOFs) and their composites, with tunable pore structures, high surface areas, and controllable wettability, offer promising solutions. This review systematically classifies design strategies and synthesis methods for MOFs and MOF-based composites tailored for oil-water separation. We highlight recent advances, emphasizing structure–function relationships. Key performance metrics from representative studies include water contact angles up to 172.3°, separation efficiencies exceeding 99.9%, and adsorption capacities reaching 168 g·g⁻¹. Challenges such as scalability, stability, and fouling resistance are discussed, along with future directions for practical implementation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4124-x
Aerogel fibers, featuring distinct porous architecture and fiber flexibility, have emerged as leading materials for personal thermal protection; however, complex drying processes and singular thermal insulation mechanisms limit their use in complex environments. Here, aramid nanofiber/carbon nanotube (ANF/CNT) aerogel fibers integrating passive thermal insulation and active solar heating were fabricated via wet-spinning and ambient-pressure drying (APD). The incorporation of CNT and Ca2+ generates abundant physical and chemical crosslinking points, strengthening the nanofiber network skeleton and reducing structural collapse during APD to only 8.9% shrinkage. The resulting ANF/CNT aerogel textiles exhibit low thermal conductivity of 33.8–40.4 mW/(m K) and thermal insulation capability from −196 to 400 °C. The photothermal effect of CNT enables active solar heating, effectively supplementing passive insulation and allowing survival in extremely cold environments. In real tests, the synergistic effect improved skin temperature by up to 5.9 °C, significantly higher than 1.6 °C from passive insulation alone. These ANF/CNT aerogel fibers combine flexibility, mechanical strength, and flame retardancy, demonstrating promising potential for smart, controllable personal thermal management applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4100-9
Shape memory droplet manipulation platforms have attracted significant attention due to their programmable droplet control capabilities. Current research primarily focuses on superhydrophobic surfaces and slippery lubricant-infused porous surfaces (SLIPS); however, these approaches suffer from vulnerable surface micro/nanostructures and loss of lubricant oils. Here, we report a shape memory quasi-liquid polydimethylsiloxane (PDMS) brush surface that overcomes these limitations. The surface is fabricated by introducing a SiO2 layer as a 'bridge' on a shape memory epoxy substrate, providing abundant functional groups for grafting PDMS brushes. By precisely controlling the SiO2 layer thickness and grafting conditions, the surface exhibits good shape memory properties and low adhesion to diverse liquids with varying surface tensions. Reversible anisotropic/isotropic droplet sliding control for both water and organic droplets is demonstrated through dynamic introduction/removal of groove structures, proving excellent droplet manipulation based on the combination of shape memory and low adhesion of PDMS brushes. Furthermore, the material can be applied as a functional coating on diverse substrates to impart anti-fouling and self-cleaning properties. This work introduces a nanoscale SiO2 layer as a 'bridge', offering a strategy to graft PDMS brushes onto polymer surfaces. Given the advantages of quasi-liquid PDMS brushes and programmable controllability of shape memory polymers, this work provides fresh ideas for developing droplet manipulation platforms.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4162-0
The urea oxidation reaction (UOR) offers a low-energy pathway for hydrogen production via water electrolysis, but Ni-based catalysts suffer from Ni self-oxidation reaction (NSOR) that wastes energy and poisons active sites via strong CO2 adsorption. Here, we design MoN/Ni heterostructures to optimize the electronic structure of Ni sites, suppressing NSOR. X-ray photoelectron spectroscopy and X-ray absorption spectroscopy confirm the formation of electron-rich Mo and electron-deficient Ni active pairs. In-situ spectroscopy, electrochemical tests, and density functional theory calculations reveal that electron-rich Mo sites enhance urea adsorption, while electron-deficient Ni sites prevent NSOR, facilitating urea activation, intermediate conversion, and CO2 desorption. The synergistic effect yields a current density of 100 mA cm−2 at only 1.39 V vs. RHE in 1 M KOH + 0.33 M urea, outperforming many NiOOH-based catalysts. This work introduces a novel high-performance catalyst with electron-rich/electron-deficient active pairs for efficient UOR.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4104-4
Covalent organic frameworks (COFs) are promising adsorbents for gas adsorption and separation, yet identifying optimal structures among their vast design space requires efficient high-throughput screening. Conventional machine-learning predictors rely heavily on specific gas-related features, which are time-consuming and limit scalability, leading to inefficiency and labor-intensive processes. Here, we propose COFAP, a universal COFs adsorption prediction framework that extracts multi-modal structural and chemical features via deep learning and fuses these complementary features through a cross-modal attention mechanism. Without relying on explicit gas-specific thermodynamic descriptors, COFAP achieves state-of-the-art prediction performance on the hypoCOFs dataset under the conditions investigated, outperforming existing approaches. Based on COFAP, we found that high-performing COFs for gas separation concentrate within a narrow range of pore size and surface area. A weight-adjustable prioritization scheme is also developed to enable flexible, application-specific ranking of candidate COFs. Superior efficiency and accuracy render COFAP directly deployable in crystalline porous materials.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3476-4
Ammonia synthesis remains dominated by the Haber-Bosch process, which operates at 400–500 °C and 150–300 bar, consumes 1–2% of global energy, and emits ~1.4% of global CO2. Ru-based catalysts supported on carbon and promoted with basic oxides (Ba, Cs, La) exhibit high activity under mild conditions, but conventional designs suffer from a trade-off: BaO domains block Ru active sites while attempting to donate electrons. Lee et al. (Nat Catal, 2025, 8: 248–256) resolved this by using conductive carbon to bridge isolated Ru and BaO domains, enabling long-range H+/e− pair migration. Screening eleven carbon supports, they identified N-doped multi-walled carbon nanotubes (10–20 nm diameter, N-MWNT-1) with the lowest work function as optimal. At a Ba/Ru molar ratio of 0.75, the catalyst achieved an NH3 production rate 7.4 times higher than conventional BaO-promoted Ru catalysts under 573 K and 1.0 MPa, using high-purity H2 and N2 (99.999%, O2 <0.4 ppm, H2O <0.7 ppm). This design decouples proton and electron storage, preventing BaO-induced blockage of Ru surfaces and enabling superior activity and stability. The Ba-Ru/carbon catalyst offers a transformative pathway for reducing energy consumption and integrating with electrolytic hydrogen production in industrial ammonia synthesis.