SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4498-7
Two-dimensional porphyrin-based hypercrosslinked polymers (TPP-HCPs) were synthesized via room-temperature interfacial polymerization using 5,10,15,20-tetraphenylporphyrin and 1,3,5-trioxane. The resulting TPP-HCPs exhibited a BET surface area of 548 m2 g-1 and a CO2 uptake of 7.97 wt% at 1 bar and 298 K. CuO/TPP-HCPs nanospheres were fabricated by thermal conversion of Cu(NO3)2·3H2O in DMF at 135 °C, using TPP-HCPs as dynamic templates. This in-situ strategy generated CuO nanoparticles within the conjugated porous matrix, facilitating electron transfer and enhancing CO2 access to catalytic centers. In CO2 electroreduction, the composite achieved a total gas Faradaic efficiency exceeding 90% at ~500 mA cm-2 (-1.4 V vs. RHE), with 40.9% for C2H4, 8.2% for CH4, 31.9% for CO, and 12.3% for H2. The catalyst maintained stability over 24 h in an H-cell. These results demonstrate that 2D conjugated polymer-templated catalysts can sustain high-rate CO2 conversion to value-added products, offering a viable route for industrial CO2 utilization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4480-1
Ternary organic solar cells (OSCs) incorporating a structurally compatible guest acceptor (C7-Cl) into the PM6:BTP-eC9 host system are demonstrated. The low Flory-Huggins interaction parameter between host and guest acceptors facilitates intimate mixing, optimizing molecular packing and energy-level alignment. High-sensitivity sEQE and EQEEL analyses reveal a reduced non-radiative energy loss (KE3) of 0.216 eV in the ternary device. Consequently, the optimized ternary OSC achieves a champion power conversion efficiency (PCE) of 20.02% and an improved T80 operational lifetime of 1065 h. This work establishes a feasible strategy via structurally compatible guest doping to simultaneously optimize vertical phase separation and suppress non-radiative loss, providing a facile and effective route toward high-performance and stable OSCs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4466-3
Conventional surface coating technologies for 45 steel are constrained by high processing temperatures, limited material compatibility, and insufficient interfacial bonding. This study introduces ultrasonic vibration-assisted mechanical coating (UVAMC) as a low-temperature deposition route that mitigates these limitations. The process yields a chromium coating on 45 steel with a nanoscale elemental interdiffusion transition layer at the interface, achieving a bonding strength of 66.0 MPa. The coating delivers improved corrosion resistance in aggressive environments while preserving the substrate's original compressive and tensile strength. The method also demonstrates broad process adaptability, successfully depositing copper, aluminum, and 316 stainless steel powders, and forming complex shapes such as the "SZU" pattern. These results establish UVAMC as a viable surface functionalization strategy for metallic materials, combining efficient deposition with operational flexibility.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4275-3
Electrochemical in-situ production of active chlorine (AC) via chlorine evolution reaction (CER) can alleviate hull corrosion and residual chlorine overage, which is a highly reliable disinfectant for sewage and ballast water. Nonetheless, the primarily competitive oxygen evolution reaction and gradual anode passivation hinder its practical application. Herein, we employed the in-situ hydrothermal strategy to synthesize Ru/TiO2-x to realize high activity and selectivity of CER. The robust interaction of Ru sites and TiO2-x achieved via a one-step hydrothermal synthesis strategy, the structural and valence state characterizations confirm that Ti3+ stabilizes Ru solely in the metallic state (Ru0) via structural confinement effects, effectively inhibiting catalyst oxidation. As a result, the Ru/TiO2-x requires only an overpotential of 33 mV to reach 10 mA cm−2, and possess strong catalytic durability, sustaining continuous operation for 100 h with negligible current decay. Further integration with a triboelectric nanogenerators successfully realizes the generation of AC, which demonstrates a >99.9% inactivation efficiency against Escherichia coli in simulated seawater environments, while also effectively degrading ammonia nitrogen and urea contaminants in domestic wastewater.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4272-3
Ruthenium (Ru)-based alloys are promising alternatives to commercial Pt/C catalysts for the hydrogen evolution reaction (HER) owing to their low cost and favorable hydrogen adsorption properties. However, the sluggish water dissociation on Ru catalysts remains a major kinetic bottleneck in alkaline solutions. Herein, we report a rare earth (RE) dilute alloy strategy by incorporating a trace amount of cerium (Ce, ~1 at%) into a RuCu alloy to promote interfacial water activation. The oxophilic Ce sites strengthen H2O adsorption and reduce the energy barrier for water dissociation, thereby accelerating the Volmer step during alkaline hydrogen evolution. Consequently, the RuCuCe catalyst delivers 10 mA cm−2 at an overpotential of only 18 mV in 1.0 M KOH and maintains stable operation for over 100 h at 500 mA cm−2 in a membrane electrode assembly. In situ electrochemical impedance spectroscopy and pH-dependent measurements verify the facilitated Volmer process induced by Ce incorporation. Temperature-dependent analysis further shows that the apparent activation energy decreases from 47.4 kJ mol−1 for RuCu to 26.4 kJ mol−1 for RuCuCe, consistent with enhanced water dissociation kinetics. This work establishes RE dilute metal alloys as an effective platform for boosting the intrinsic activity of Ru-based alloy catalysts, in which RE incorporation promotes water dissociation while inducing charge redistribution in the alloy matrix.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4281-7
Multispectral camouflage materials must simultaneously address visible and infrared (IR) detection while maintaining environmental stability and mechanical flexibility for deployment in harsh conditions. This work presents a multilayer composite integrating a colorful, IR-transparent visible reflection (VR) layer, a low-emissivity graphene (LEG) layer, and an aramid nanofiber (ANF) aerogel layer. The VR layer provides tunable visible colors without compromising the low-emissivity property of the LEG layer, which achieves IR emissivity between 0.30 and 0.43. The ANF aerogel, reinforced with a grid structure, reduces thermal conduction, lowering IR radiation intensity by 40% at an 80 °C heat source. The composite exhibits effective electromagnetic interference (EMI) shielding and maintains multifunctional stability in strong acid, strong alkali, saline, and organic media. This design offers a novel strategy for environmentally robust multispectral camouflage materials suitable for extreme operational environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4234-3
The pursuit of high-energy-density sodium-ion batteries (SIBs) necessitates the development of stable high-capacity anodes. While amorphous carbon is a promising anode candidate for SIBs, its practical application is hindered by limited capacity. Herein, we design a composite anode by chemically confining a high-content (~25 wt%) short-chain sulfur into hierarchical porous hard carbon microspheres (SHHC) derived from microbe yeast. The SHHC anode exhibits a high reversible capacity of ~807 mAh g−1 at 0.03 A g−1 (~3 times that of conventional amorphous carbon) along with superior rate capability, and extraordinary long-term cyclability (almost 100% capacity retention after 2000 cycles at 1.0 A g−1). The high-content sulfur species contribute to superb redox reactivity for high-capacity sodium storage via a surface-dominated storage mechanism. The carbon matrix features an enlarged interlayer distance, which facilitates Na-ion intercalation and deintercalation for high-rate capability. Furthermore, the hierarchical porous structure with built-in cavities facilitates the Na-ion transfer and effectively accommodates the electrode’s volume expansion, achieving fast electrode kinetics and outstanding cyclability. Such a combination of favored properties leads to state-of-the-art comprehensive battery performance for Na-ion storage. Our finding envisions a new perspective on building stable high-capacity anode materials for SIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3682-6
Metal single-atoms with optimized coordination structure on highly accessible substrate can maximize the metal utilization efficiency along with enhancing catalytic activities. Herein, axial nitrogen-coordinated Fe-N5 sites on N-doped carbon (denoted as FeN5@N-C) hollow microplates are fabricated via a unique Fe3+-chelated polydopamine assisted hollowing strategy using ZIF-L microplates as multifunctional templates. Due to the powerful chelating and adhesive ability of polydopamine, this hollow-carbon strategy can be extended to fabricate single-atom Fe-N-C hollow structures with different shapes and encapsulate other transition-metal single atoms (Ni, Co, Mn, and Cu) into the N-doped carbon hollow microplates. The FeN5@N-C hollow microplates exhibit outstanding oxygen reduction reaction (ORR) capability with an impressive half-wave potential of 0.93 V vs. reversible hydrogen electrode and high stability, which can serve as air-cathode catalysts for high-performance Zn-air batteries with high peak power density of 225.3 mW cm−2 and stable cyclability of up to 400 h. Comprehensive analysis and theoretical calculations elucidate that axial nitrogen coordination in Fe-N5 catalytic sites, unlike the planar Fe-N4 configuration, can compete well with the bonding of OH* through additional 3d-2p orbital hybridization, thereby giving moderate bonding strength to enhance the ORR activity.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3663-6
Escalating global climate change has precipitated a dramatic surge in building cooling/heating energy demands, critically undermining urban sustainability. Although dynamic thermal management technologies show potential for reducing architectural carbon footprints, prevailing active regulation systems remain constrained by energy-intensive mode-switching mechanisms and unsustainable operational costs. Here, we develop a zebra-inspired radiative modulator (ZIRM) that achieves climate-customized building thermal management through spatially partitioned integration of radiative cooling (RC) and heating (RH) functional units. The material breakthrough resides in a hybrid thin-film architecture combining a cellulose acetate/Zeolitic imidazolate framework-L (ZIF-L) porous membrane (solar reflectance ~95%, thermal emissivity ~0.88) with an MXene/ZIF-67 derived carbon-based absorption layer (solar absorption ~93%, thermal emissivity ~0.37), resolving the opto-thermal coupling limitations inherent to conventional materials. Experimental verification demonstrates that programmable regulation of the RC/RH area ratio enables broad-range temperature differential control from −4.3 to 12.1 °C during daytime operation. Building energy simulations reveal ZIRM’s annual energy consumption of 1.45×10^10 GJ, corresponding to 9.9% and 2.7% reductions compared to pure RC and RH systems, respectively. The established “configuration-environment-performance” predictive model pioneers a paradigm-shifting solution for carbon-neutral architecture, synergizing material innovation with climate-customized engineering strategies.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507085
This study investigates the spatiotemporal differentiation of suspended particulate matter (SPM) characteristics, sources, and their impacts on water quality between the Middle Route (closed artificial channel) and East Route (open natural water system) of the South-to-North Water Diversion Project. Thirty sampling sites (13 on the Middle Route, 17 on the East Route) were established, and samples were collected during dry and wet seasons. Water quality parameters and SPM characteristics were analyzed, including particle size distribution, total suspended solids (TSS), chlorophyll a, and stable carbon and nitrogen isotopes. Results show that the Middle Route maintains good and stable water quality, with SPM dominated by coarse particles (>63 μm, 61.43%–94.68%), total phosphorus (TP) <0.01 mg·L−1, and a significant positive correlation between chlorophyll a and coarse particles (r=0.60), indicating algal aggregation dominates particle formation. In contrast, the East Route exhibits high and fluctuating nitrogen and phosphorus concentrations, with SPM dominated by fine particles (<20 μm, 51.26%–88.61%), TP ranging from 0.03 to 1.11 mg·L−1, and a positive correlation with fine particles, suggesting significant external inputs. Carbon and nitrogen isotope analysis reveals that Middle Route SPM primarily originates from autochthonous algae (contribution >46.75%), while East Route SPM is influenced by both terrestrial C3 plants and algae. The distinct engineering and management approaches of the two routes lead to significant differences in SPM characteristics and sources, thereby affecting water quality dynamics. The Middle Route requires an 'algal reduction and hydrodynamic optimization' strategy to control algal-derived coarse particle deposition, whereas the East Route benefits from 'retention-sedimentation and wetland purification' to reduce external fine particles and pollutant inputs. This research provides theoretical support and practical guidance for differentiated SPM management in long-distance water diversion systems.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604004
Tire wear particles (TWPs) are emerging pollutants and constitute the dominant type of microplastics (MPs) in urban stormwater runoff, accounting for up to 90% of MPs in some cases. They are characterized by small size, high mobility, complex composition, and significant toxicity. Current research on TWPs remains fragmented, lacking a comprehensive understanding of their environmental behaviors and pollution control in aquatic systems. This review systematically analyzes the enrichment and vectoring roles of TWPs for coexisting pollutants, and their environmental fate, including ecotoxicological impacts, detection methodologies, release of intrinsic additives, and aggregation and sedimentation behaviors. Drawing on insights from other microplastic studies, the paper explores control technologies across the pollution pathway—source, transport, and terminal treatment—and proposes feasible management strategies. Key findings indicate that TWPs can adsorb heavy metals and organic contaminants, with adsorption capacities influenced by aging processes. Their aggregation is governed by solution chemistry, with critical coagulation concentrations varying with ionic strength and pH. The release of additives such as zinc and benzothiazoles is significant, posing ecological risks. Future research should focus on real-water aggregation mechanisms, additive release under natural conditions, long-term performance of treatment facilities like constructed wetlands under TWPs stress, enzymatic degradation pathways, and integration of AI, big data, and IoT for cost-effective detection and risk modeling. This review provides a scientific basis for developing targeted pollution control measures for TWPs in aquatic environments.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61100-6
Sodium-ion capacitors (SICs) are attractive for low-cost and safe energy storage, but their practical development is limited by sluggish Na+ storage kinetics and structural instability of anodes. Control of both bulk structure and surface chemistry can address these limitations. We report a heteroatom-rich porous carbon (HRPC) derived from spores via hydrothermal pretreatment, low-temperature carbonization, and acid-mediated functionalization. The optimized GLSHC-HNO3 anode exhibits hierarchical porosity and multi-element co-doping, enabling rapid ion/electron transport, improved electrolyte wettability, and abundant Na+ adsorption sites. Density functional theory calculations reveal distinct contributions of different heteroatom configurations to sodium adsorption. The HRPC anode delivers an ultrahigh reversible capacity of 446.1 mAh g−1 at 50 mA g−1, retains 237.3 mAh g−1 at 2 A g−1, and shows excellent cycling stability. A full SIC with a polyaniline-derived porous carbon cathode achieves an energy density of 114.4 Wh kg−1 at 290 W kg−1, 43.1 Wh kg−1 at 1450 W kg−1, and a maximum power density of 5800 W kg−1, with 84.3% capacity retention after 5000 cycles and nearly 100% Coulombic efficiency. This work establishes a scalable, sustainable route for converting biomass into high-value carbon anodes, providing a new pathway for high-performance sodium-ion energy storage.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010802
Ozone (O3) pollution is a prominent issue in the Guanzhong Plain, necessitating effective control of its precursors, particularly volatile organic compounds (VOCs). However, studies on VOC pollution characteristics at the county level are scarce. To investigate the summer VOC pollution characteristics and sources in high-altitude towns of the Guanzhong Plain, continuous monitoring of 53 typical VOC species was conducted at two sites in Changwu County, Xianyang City (elevation 1200 m). The spatiotemporal variations of ambient VOCs and their ozone formation potential (OFP) were analyzed, and source apportionment was performed using the Positive Matrix Factorization (PMF) model. Results showed that average total VOC (TVOCs) concentrations at the Changwu Government and Changwu Middle School sites were 60.04×10⁻⁹ and 83.28×10⁻⁹, respectively. Oxygenated VOCs (OVOCs) dominated, accounting for 55.14% and 62.91% of TVOCs, followed by alkenes, aromatic hydrocarbons, and halogenated hydrocarbons. Industrial sources contributed the most (43.2%) to VOC emissions in Changwu County, but site-specific differences were observed: the Government site was primarily influenced by solvent use (30.7%) and motor vehicles (19.1%), while the Middle School site was dominated by domestic sources (27.6%) and motor vehicles (20.0%). The average OFP values at the Government and Middle School sites were 258.84×10⁻⁹ and 378.04×10⁻⁹, respectively, with alkenes and OVOCs as the main contributors, originating from industrial emissions, solvent use, and biogenic sources. EKMA curves indicated that Changwu County was in a VOC-limited regime during the observation period, confirming the effectiveness of VOC control for ozone mitigation. These findings provide scientific guidance for local ozone management and offer a paradigm for precise ozone pollution control in county-level regions of the Guanzhong Plain.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025011503
This study investigated odor emissions from a large-scale ink manufacturing enterprise through comprehensive analyses of odor concentration, substance concentration, and characteristic odor compounds across all exhaust stacks. The aim was to assess odor dispersion patterns and identify critical odor-generating processes to inform strategic upgrades of air pollution control systems. The results showed that acrolein, hydrogen sulfide, isobutyraldehyde, m-xylene, p-xylene, and ethanol were screened as typical odor substances, with acrolein being ubiquitously present across all emission processes. The odor dispersion radius extended 1.4–2.6 km beyond the facility boundary. Vertical odor impact at a sensitive point 1 km from the plant boundary revealed a parabolic profile: concentrations initially increased with height, peaked at 30 m (equivalent to a 10-story building), then decreased at higher heights. The exhaust stack of the sewage treatment station accounted for 53.26% of total odor emissions, establishing this system as the priority control node for implementing enhanced air purification technologies in industrial air quality management.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225264
The high cost of high-purity hydrogen necessitates the utilization of low-cost industrial by-product hydrogen as an alternative gas source to reduce hydrogen storage costs. Industrial by-product hydrogen typically contains impurities such as H2S and CO, yet the poisoning mechanisms of these gases on superlattice hydrogen storage alloys during hydrogen absorption/desorption remain poorly understood. This study systematically investigates the poisoning effects and regeneration behavior of La0.65Mg1.32Ca1.03Ni9Y0.17 superlattice hydrogen storage alloy in atmospheres containing 10^-3 H2S and CO. The experimental protocol comprised 10 poisoning cycles followed by 1 regeneration, repeated to total 20 poisoning cycles and 2 pure hydrogen regenerations. Results show that in pure hydrogen, the alloy's hydrogen storage capacity gradually decreases after 22 cycles but is effectively restored after dehydrogenation at 473 K. In the presence of impurity gases, the hydrogen storage capacity retention rates after 10 poisoning cycles with H2S and CO are 3.56% and 2.71%, respectively; after 20 cycles, these decrease to 3.68% and 1.73%, respectively. After dehydrogenation at 473 K, retention rates recover to 40.35% and 98.27%, respectively. This indicates that poisoning severity follows the order CO > H2S, while regeneration difficulty follows H2S > CO. X-ray diffraction analysis reveals that after poisoning, the main phase transforms from AB3 to AB3H, but reverts to AB3 after high-temperature dehydrogenation. X-ray photoelectron spectroscopy shows that after H2S poisoning, CaS and CaSO4 form on the alloy surface, indicating irreversible chemical adsorption. In contrast, after CO poisoning, no new substances are detected, indicating reversible adsorption. This study clarifies the differentiated poisoning mechanisms of impurity gases and provides theoretical support for the application of rare-earth superlattice hydrogen storage alloys in complex atmospheres.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3833-1
Developing plasmonic nanomaterials with compositions beyond noble metals is crucial for expanding their applications. Transition metal nitrides, such as titanium nitride (TiN), exhibit excellent plasmonic optical properties and photothermal conversion efficiency, showing promise in catalysis, photothermal therapy, and seawater desalination. However, the structure-property relationship governing their plasmonic optical properties remains unclear. Here, we constructed Au@TiN core-shell nanostructures and systematically investigated the tunability of their geometry, composition, and optical properties. By varying the Au core size and TiN shell thickness, we achieved precise control over the localized surface plasmon resonance (LSPR) from visible to near-infrared wavelengths. Single-particle scattering spectroscopy revealed distinct plasmon hybridization modes, with experimental spectra matching theoretical simulations. The Au@TiN nanostructures exhibited enhanced photothermal conversion efficiency (η = 78.5%) under 808 nm laser irradiation, significantly outperforming pure TiN nanoparticles (η = 45.2%). This work demonstrates multi-factor control over plasmonic effects in TiN, providing insights for designing TiN-based plasmonic nanomaterials for catalysis and sensing.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3937-7
Triple-negative breast cancer (TNBC) remains a formidable clinical challenge due to its high invasiveness and adaptive resistance. We report a bio-mimetic nanoplatform (HMPB-GOx@HSA-Cu2+) integrating starvation therapy, Fenton/Fenton-like catalysis, and mild photothermal therapy (mPTT) for synergistic TNBC treatment. The nanoreactor comprises a hollow mesoporous Prussian blue (HMPB) core loaded with glucose oxidase (GOx), encapsulated in a human serum albumin (HSA) shell covalently functionalized with Cu2+ ions. This design enables spatiotemporal control of Cu2+-mediated Fenton catalysis, responding to the tumor microenvironment (TME) to generate cytotoxic hydroxyl radicals (·OH). GOx catalyzes glucose depletion, elevating H2O2 levels and acidity, thereby enhancing catalytic efficiency. Concurrently, mPTT at ~43–45°C accelerates the Fenton reaction and suppresses heat shock protein (HSP) expression, overcoming thermal tolerance via ATP depletion. In vitro and in vivo studies demonstrate significant anti-tumor efficacy through reactive oxygen species (ROS) accumulation and metabolic disruption, with excellent biocompatibility. This work presents a highly integrated strategy for precise TNBC therapy, addressing limitations of conventional monotherapies.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511020
With the increasing number of oil pipelines crossing rivers, the potential risks of oil leakage and surface spreading to river ecosystems and water environments are becoming more severe. Scenario-based simulation of oil spill diffusion is a prerequisite for effective interception point placement and leakage risk prevention. Numerous factors influence oil spill diffusion, including environmental conditions, river hydrology, and accessibility of emergency resources. This study integrates these factors and multiple dynamic processes to design eight typical scenarios for oil spill diffusion simulation, considering emergency resource locations, river hydrological regimes, and leakage modes. A case study is conducted on an oil pipeline crossing a river in northwest China. Results indicate that the diffusion distance and affected area are primarily controlled by water conditions and emergency resource accessibility. In emergency management, the efficiency of maintenance and repair resources during high-water months should be prioritized. Mechanistically, external forces such as hydraulic and wind forces have a greater influence on diffusion distance, surpassing internal forces like gravity, viscosity, and surface tension within a short time. For river crossings near emergency resources, internal force effects should be considered in oil spill diffusion simulations. When emergency resource arrival times are long, the diffusion distance based on Fay's theory is relatively small and can be neglected in engineering practice. This study provides a computational basis and methodological reference for risk assessment and emergency response to potential oil spills from pipelines crossing rivers, enhancing the scientific and effective nature of risk prevention and emergency handling.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0037
Alumina microspheres with a lamellar-assembled flower-like morphology were synthesized via a urea-assisted hydrothermal method and used as supports to prepare Pd/Al2O3-M catalysts by incipient wetness impregnation. The catalytic performance was evaluated in the selective hydrogenation of isoprene and the hydrogenation of 2-ethylanthraquinone for hydrogen peroxide production, and compared with a commercial alumina-supported Pd catalyst (Pd/Al2O3). Characterization revealed that the flower-like structure, composed of stacked nanosheets, promoted high Pd dispersion and enhanced metal-support interaction, leading to a higher surface Pd content and more abundant active sites. Under 60 °C and 1 MPa H2, Pd/Al2O3-M achieved 95.2% conversion of isoprene with 98.3% total selectivity to isoamylenes, and exhibited good stability over 24 h. In anthraquinone hydrogenation, it reached a hydrogenation efficiency of 15.8 g/L, a 27.4% improvement over Pd/Al2O3 (12.4 g/L). The study demonstrates that modulating carrier morphology is an effective strategy to simultaneously enhance activity, selectivity, and stability of Pd catalysts, offering a promising approach for designing efficient hydrogenation catalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4000-1
Formamidine lead-based perovskites (FAPbI3) exhibit significant potential in optoelectronic applications. Nevertheless, they encounter challenges related to δ-phase instability and reliance on toxic solvents. In this study, we present a green solvent-additive synergy strategy that employs γ-valerolactone (GVL) in conjunction with reductive acids like oxalic acid (OA), to stabilize α-FAPbI3 single crystals (SCs). GVL enhances the stability of the precursors through the formation of FA+-GVL hydrogen bonds and high-valence [PbIx]2−x clusters, resulting in ambient-stable α-phase SCs, yielding a marked improvement in stability compared to SCs prepared with the toxic solvent γ-butyrolactone (GBL). Additive modulation demonstrates that H+ and reductive groups play a critical role in regulating crystallization, suppressing the δ-phase by promoting FA+ dissociation and inhibiting MA+ deprotonation. A solvent-involved intermediate, δ-FAPbI3-GVL, has been identified; this intermediate evolves into α-FAPbI3 at a low temperature of 60 °C, thereby reducing the energy barriers associated with the α to δ phase transition. In contrast, non-reductive acids and reductive ionic liquids do not inhibit δ-phase formation, with the latter even promoting the crystallization of pure δ-FAPbI3. By utilizing low-volatility OA as an additive, optimized FA0.9MA0.1PbI3 single crystal thin films exhibit a low defect density of 8.3 × 10^11 cm−3. Subsequently, a photodetector was fabricated. Under zero bias voltage and 780 nm illumination, the device exhibited a responsivity of 14.5 mA/W, a detectivity of 3.75 × 10^10 Jones, and a response speed of 149/65 μs. Moreover, without any encapsulation, the device’s performance diminished by only 17% after 30 days of storage in ambient conditions, indicating remarkable stability.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60748-7
Cyclohexene is a crucial raw material for nylon production, and the selective hydrogenation of benzene is a key route for its preparation. To promote data sharing and reuse in this field, we collected and standardized experimental data on the hydrogenation of benzene to cyclohexene from publicly available literature, constructing a comprehensive dataset containing catalyst composition, reaction conditions, and reaction results (conversion, selectivity, and yield). This data descriptor details the source, field definitions, generation and processing workflow, quality control, sharing approach, and usage recommendations of the dataset, aiming to provide a reusable data foundation for subsequent statistical analysis, machine learning modeling, experimental design, and catalyst screening. The dataset is provided in Excel format and is accessible via GitHub and ScienceDB. It addresses the lack of unified field definitions, unit systems, and organizational formats in scattered literature data, enabling direct statistical analysis, correlation mining, and predictive modeling. The dataset is expected to accelerate research in optimizing ruthenium-based catalytic systems for selective benzene hydrogenation, which currently suffer from limited cyclohexene yield despite the use of aqueous-phase systems and inorganic salt additives. By offering a quality-controlled, structured dataset, this work supports data-driven approaches to overcome the thermodynamic favorability of complete hydrogenation to cyclohexane and to improve process economics.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608009
To investigate the flow and heat transfer characteristics of natural draft direct air-cooling towers (NDC) for large coal-fired power generating units, a three-dimensional CFD numerical model covering major plant buildings, air-cooled radiators, and ambient wind fields was established based on the NDC systems of a 2×660 MW unit of a power plant. The influences of meteorological factors, including ambient wind speed, ambient temperature, and ambient wind direction, as well as regulation measures such as rolling shutters, louvers, and bypass windows on the heat dissipation performance of NDC towers were systematically analyzed. The results demonstrate that ambient wind speed acts as the dominant factor governing the performance of the NDC system. As wind speed rose, the uneven distribution of air intake volume and heat dissipation among each cooling delta increased remarkably, which elevated the unit back pressure, and the upstream tower suffered more severe impacts than the downstream one. Ambient temperature exerted a slight effect on circumferential flow distribution, yet substantially changed the overall back pressure of the system. In terms of regulation strategies, closing rolling shutters in the windward zone and reducing the opening of partial louvers can improve air flow redistribution to a certain extent, but will reduce the total air flow rate and total heat dissipation of the entire tower. By contrast, bottom bypass windows can effectively optimize the air intake on the leeward side and boost heat dissipation under high-wind operating conditions, whereas top bypass windows deliver only limited improvement effects. This research can provide fundamental data and technical references for the optimal design, operational regulation, and energy-saving retrofitting of large NDC units.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4129-y
Therapeutic biosynthesis is a promising strategy for precision cancer therapy, yet achieving controlled synthesis of abiotic materials within tumors remains challenging. Here, we report a “dual lock-and-key” system for tumor-specific intracellular synthesis. The precursor, termed “dual-lock,” is activated by two endogenously overexpressed enzymes—azoreductase (AzoR) and nitroreductase (NTR)—acting as “dual keys” in target cancer cells. This activation triggers a condensation reaction that produces fibrous mesh covalent organic polymers (Fm-COPs) in situ. Synthesized Fm-COPs effectively disrupt the cytoskeleton, inhibiting cell migration and invasion while inducing apoptosis. In vivo studies demonstrate that this strategy achieves specific tumor enrichment and deep penetration, leading to significant tumor growth inhibition (tumor inhibition rate >70%) without systemic toxicity, as evidenced by stable body weights and normal histopathology. The dual enzyme-responsive mechanism ensures high selectivity, and the small-molecule precursors facilitate efficient tumor penetration. This work presents a next-generation approach for high-precision cancer therapy, offering a biocompatible and autonomous strategy for intracellular synthesis.