SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4339-7
Neuromorphic computing demands energy-efficient synaptic devices that emulate biological plasticity. Optoelectronic memristors based on colloidal quantum dots (QDs) offer tunable bandgaps and solution processability, yet suffer from defect-mediated nonradiative recombination and instability. Here, we report ZnS-passivated CdZnSe core/shell QDs as the active layer in memristive devices, achieving enhanced synaptic emulation and information encryption. Time-resolved photoluminescence (TRPL) decay curves were fitted with a tri-exponential function, revealing that ZnS passivation suppresses defect-related trap states, prolonging the average carrier lifetime from 12.3 ns (CdZnSe) to 28.7 ns (CdZnSe/ZnS). The intensity proportion of the fast decay component (τ1 ≈ 1.2 ns) decreased from 45% to 18%, indicating reduced surface trapping. Devices incorporating CdZnSe/ZnS QDs exhibit stable bipolar resistive switching with an ON/OFF ratio exceeding 10^3, endurance of >10^3 cycles, and retention of >10^4 s. Under 365 nm UV illumination, the devices show light-tunable synaptic plasticity, including paired-pulse facilitation (PPF) with a facilitation index of 180% at a 50 ms interval, and transition from short-term to long-term memory. The memristors successfully emulate essential synaptic functions and are employed in a simple encryption scheme, demonstrating the potential of defect-passivated QDs for secure neuromorphic hardware.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4043-3
In-plane InAs nanowires and nanowire networks are promising platforms for electronics, optoelectronics, and topological quantum computing due to their small electron effective mass, narrow bandgap, high electron mobility, strong spin-orbit coupling, and large Landé g factor. However, their selective area growth on CMOS-compatible group-IV substrates remains challenging. Here, we report the selective area growth of high-quality in-plane InAs nanowires and nanowire networks on Ge(111) substrates by molecular-beam epitaxy. Conventional selective-area epitaxy fails to simultaneously achieve good selectivity and continuity. To overcome this, we developed a metal-sown, single-indium-source two-step growth method, which attains both selectivity and continuity but yields nanowires with rough surfaces and lengths below 10 μm. We then introduced an upgraded metal-sown, dual-indium-source two-step growth method, successfully fabricating in-plane InAs nanowires and nanowire networks with smooth surface morphology and lengths exceeding 60 μm. By optimizing the As beam equivalent pressure, overgrowth at network junctions is effectively suppressed, resulting in uniform nanowire networks. High-resolution transmission electron microscopy and Raman spectroscopy confirm the high-quality single-crystalline nature and pure zinc-blende structure of the nanowires and networks. This work establishes a foundation for fabricating high-quality in-plane InAs/superconductor hybrid nanowires and nanowire networks on Ge substrates.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510084
The rapid expansion of lithium battery industries has elevated lithium resources to strategic importance, yet lithium extraction generates 8–10 tons of slag per ton of lithium salt, with complex heavy metal content and high leaching risks. This study improves conventional alkali activation by employing a composite activator and multi-stage thermal assistance to achieve self-solidification of lithium slag, simultaneously immobilizing multiple heavy metals while producing high-strength materials. Under full slag conditions, the mechanical strength of solidified materials ranged from 3.48 to 8.25 MPa; after optimization, strength increased by 137.07%. Average immobilization rates for various heavy metals rose from 97.26% to 99.77%. In simulated acidic, alkaline, neutral, high-salt, acid rain, and leachate environments, efficient immobilization was maintained, with leachate concentrations below regulatory limits. The improved activator and thermal process reduced structural defects, promoted formation of the key Si-O-Al framework, and ensured structural integrity, enhancing both mechanical strength and heavy metal immobilization. The cost of slag solidification was approximately 185–200 CNY per ton, significantly lower than conventional methods, with low energy consumption, no high-temperature calcination, and reduced equipment and reagent requirements, supporting scalability.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510060
Wastewater treatment plant (WWTP) effluent is a significant pathway for emerging contaminants (ECs) to enter natural water bodies. This study investigated the removal of ECs by two field-scale gravel-based constructed wetlands: a horizontal subsurface flow constructed wetland (QL-CW) and a surface flow constructed wetland (BL-CW), both treating actual WWTP effluent. The influence of operation mode and wetland plant type on EC removal was examined. Using liquid chromatography-mass spectrometry, principal component analysis, and ecological risk assessment, the removal efficiencies and mechanisms for various ECs were explored. In QL-CW, biodegradation was more pronounced, particularly via ammonia-oxidizing bacteria co-metabolism, favoring ECs with benzyl, secondary amine, secondary amide, tertiary amide, halogenated, and carboxyl functional groups. In BL-CW, electrostatic attraction and hydrophobic interactions were more significant, with plant and root-microorganism uptake and adsorption playing key roles. Surface flow mode achieved significantly higher removal of antibiotics (45.3% vs. 34.1%) compared to horizontal subsurface flow, while no significant differences were observed for non-antibiotic pharmaceuticals (66.6% vs. 64.4%) and pesticides (49.8% vs. 34.2%). Planting Cyperus alternifolius (windmill grass) was more beneficial for antibiotic removal (43.6% vs. 30.1%) than planting Ipomoea aquatica (water spinach). The wetlands effectively reduced the ecological risks of most ECs to marginal levels. This study provides insights into the deep treatment of ECs in WWTP effluent by constructed wetlands.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3825-x
Polymer-based dielectric materials with high energy density and thermal stability are critical for modern electric/electronic industries. Polyimide (PI) based materials are promising due to their high temperature resistance and chemical inertness, yet their inherently low dielectric constant and limited charge-discharge energy density restrict applications in film capacitors. While incorporating ferroelectric or conductive fillers can enhance dielectric performance, batch-to-batch inconsistency and physical deterioration remain problematic. This study focuses on molecular structure design and modulation, preparing hyperbranched polyimides with different dianhydride monomers and branching degrees. The effects of chain packing density with polar groups on dielectric and energy storage performances were systematically investigated via experimentation and molecular simulation. Results demonstrate a significant correlation between monomers' electrical distribution and packing density in polymer systems. Molecular simulation further elucidated the underlying mechanism. This work establishes a foundation for designing polymer-based dielectric materials with high dielectric and energy storage performances at the molecular level.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608011
Tetracycline, a poorly biodegradable organic pollutant, poses a serious threat to aquatic environments. Fenton-like methods have attracted attention for their high efficiency in treating tetracycline-containing wastewater by generating hydroxyl radicals (·OH) via H2O2 activation, thereby improving wastewater biodegradability. This review systematically summarizes recent advances in improved Fenton methods (electro-, photo-, and sono-Fenton) and heterogeneous Fenton systems, detailing reaction mechanisms, treatment efficiencies, and technical features. Under optimized conditions, tetracycline removal rates exceed 90% for various methods. Heterogeneous Fenton methods demonstrate superior applicability over a wider pH range, reduced iron sludge production, and excellent catalyst recyclability, representing the most promising strategy for practical implementation. Future perspectives emphasize developing novel catalysts, optimizing reactor design, controlling toxic by-products, and integrating hybrid technologies to facilitate practical application.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4144-y
Developing efficient strategies for electrically manipulating two-dimensional magnetism at room temperature is a key challenge in contemporary spintronics. In this study, we demonstrate giant electromechanical control over the magnetism of the room-temperature van der Waals ferromagnet Fe3GaTe2 by integrating it with the ferroelectric α-In2Se3. Modest gate voltages lead to an almost complete suppression of the coercive field by 96.5%, corresponding to a remarkable peak modulation sensitivity of ~8.1 mT V−1, which stands out among existing van der Waals magnetoelectric systems. Importantly, this substantial magnetoelectric response is predominantly unaffected by voltage polarity, as both positive and negative gate voltages induce similar magnetic modulation effects. To elucidate the underlying mechanism, we tracked the voltage-induced Raman spectral changes, revealing a peak shift of 1.7 cm−1 that accurately represents an effective in-plane tensile strain of ~1.42% under an equivalent bias, demonstrating polarity independence as well. The synchronized magnetic response and strain variation unequivocally indicate that the induced tensile strain serves as the fundamental physical driver behind the magnetic modulation. Additionally, density functional theory calculations corroborate that the reduction in magnetic anisotropy induced by tensile strain results in a decrease in the coercive field. Our work establishes a novel and efficient approach for achieving voltage control of magnetism at room temperature in van der Waals multiferroic heterostructures, highlighting their significant potential for applications in ultra-low-power magnetic logic and sensing technologies.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3643-8
Inverted perovskite solar cells (PSCs) suffer from defect-mediated nonradiative recombination and inefficient charge extraction, particularly at the buried interface and grain boundaries (GBs), which limit power conversion efficiency (PCE) and operational stability. This study introduces a multifunctional phosphonic acid molecule, (2-(3,6-bis(trifluoromethoxy)-9H-carbazol-9-yl)ethyl)phosphonic acid (M28), as an additive in the perovskite precursor solution. M28 spontaneously segregates toward the buried interface and GBs, fulfilling three roles: (1) slowing crystallization to enlarge grains and improve film quality, (2) passivating defects to suppress charge recombination, and (3) inducing p-type doping to create an extra electric field that promotes hole transport. Devices incorporating M28 achieve a champion PCE of 25.96% and retain 80% of initial efficiency after 1500 h of maximum power point tracking. This work demonstrates the efficacy of multifunctional phosphonic acid additives in addressing buried-interface and GB defects, offering a viable route to high-performance, stable inverted PSCs.