SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4500-8
Electroreduction of CO2 to ethylene offers a promising route for renewable electricity storage, yet achieving high ethylene selectivity at industrial current densities remains challenging due to the large energy barrier for C–C coupling. Here, we report a “MOF-assisted in situ doping” strategy to introduce the oxophilic nonmetal phosphorus (P) into the copper oxide (CuO) lattice, constructing a localized Cu–P dual-site adsorption configuration for the key *OCCHO intermediate. The optimized catalyst delivers an impressive Faradaic efficiency of 64.6% for ethylene with a partial current density of 646 mA cm-2. Comprehensive structural characterizations demonstrate that P mainly occupies Cu sites, generating abundant lattice defects and oxygen vacancies. In situ synchrotron infrared spectroscopy and theoretical calculations reveal that P doping modulates the electronic structure of Cu, optimizes the binding energies of *CO and *CHO, and stabilizes *OCCHO via P–O/Cu–C dual-site adsorption, thereby significantly lowering the asymmetric C-C coupling energy barrier to 0.74 eV. This work highlights a dual-site microenvironment regulation strategy for CO2-to-ethylene electroreduction.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4483-x
The referenced literature comprises five peer-reviewed studies published between 2025 and 2026 in Nature Materials, Journal of the American Chemical Society, Nature Communications, and Science China Materials. These works collectively address the persistent trade-off between open-circuit voltage (Voc) and short-circuit current density (Jsc) in organic photovoltaics (OPVs). Tao et al. (Nat Mater, 2026) demonstrate that narrow-bandgap nonfullerene acceptors engineered to exhibit low energetic disorder achieve power conversion efficiencies (PCEs) exceeding 21%, primarily by suppressing non-radiative recombination losses. Westbrook et al. (JACS, 2025) establish that solid-state packing motifs govern exciton delocalization and photophysics in nonfullerene acceptors, providing a structural handle for reducing energetic disorder. Jiang et al. (Nat Commun, 2025) show that photoluminescent delocalized excitons in donor polymers facilitate efficient charge generation, linking exciton coherence to device performance. Zhang et al. (Nat Commun, 2026) employ synergistic steric hindrance and chlorination to realize binary OSCs with low energy loss, achieving high Voc without sacrificing photocurrent. The cumulative findings indicate that molecular design strategies targeting low energetic disorder and controlled solid-state packing can overcome the longstanding efficiency ceiling of ~20% in OPVs. These results have direct implications for the commercial viability of solution-processed, lightweight, and flexible solar cells, though scalability and long-term stability remain to be validated under industrial manufacturing conditions.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4491-3
Magnetic tunnel junctions (MTJs) with multiferroic tunneling barriers offer a pathway to fully electrically controlled multi-state memory, addressing the high energy costs and scalability limits of magnetically controlled counterparts. In this work, we propose a theoretical design achieving four or ten distinct resistance states via electrical control, with a giant tunneling magnetoresistance (TMR) ratio of 1.1×10^4% (11000%). This value surpasses all previously reported MTJs, including experimental systems such as CoFeB/MgO/CoFeB (TMR 65%, 4 states) and theoretical systems like Ga2O3/MgO/Ga2O3 (TMR 1120%, 2 states). The multiferroic barrier enables simultaneous control of ferroelectric and magnetic order parameters, allowing reversible switching between multiple resistance levels without external magnetic fields. Our first-principles calculations reveal that the high TMR arises from spin-dependent tunneling through the barrier, modulated by the ferroelectric polarization direction and magnetization configuration. The device operates with low write energy and exhibits non-volatile retention, making it suitable for high-density storage and in-memory computing. This work establishes a new benchmark for electrically controlled MTJs and provides a practical route to overcome the limitations of current spintronic memory technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4285-2
Ionic conductive hydrogels have gained extensive attention in the field of intelligent sensing due to their good flexibility, tunable electrical conductivity, and multi-stimuli responsiveness. However, hydrogels easily freeze, dehydrate or swell in external environments, and thus losing their original structure and functions. Therefore, improving the environmental adaptability of conductive hydrogels remains a challenge. Herein, ionic hydrogels were encapsulated in real time via UV-assisted multi-material coaxial direct ink writing (DIW) 3D printing, and ionic conductive hydrogel sensors with array structures were prepared. The core ionic conductive hydrogel is isolated from the external environment by the hydrophobic photocurable polydimethylsiloxane (PDMS) shell resin. The PDMS shell resin isolates the core hydrogel from moisture and heat in the external environment, thereby significantly enhancing the sensor’s stability. After 60 days of storage at 25 °C, the 3D-printed coaxial array sensor exhibits only 2.5% mass loss; when stored underwater for 60 days, its swelling rate is merely 1.5%. This sensor exhibits high strain sensitivity with a gauge factor (GF) up to 1.705 and good cyclic stability, demonstrates stable operation over a wide temperature range of -20°C to 120°C, and can withstand underwater and solvent environments. It has been successfully applied in various scenarios such as human motion monitoring, underwater sensing, and temperature sensing. This research breaks through the environmental limitations of conventional hydrogel sensors and provides a simple, efficient method for developing flexible sensors with high environmental adaptability.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4281-7
Multispectral camouflage materials must simultaneously address visible and infrared (IR) detection while maintaining environmental stability and mechanical flexibility for deployment in harsh conditions. This work presents a multilayer composite integrating a colorful, IR-transparent visible reflection (VR) layer, a low-emissivity graphene (LEG) layer, and an aramid nanofiber (ANF) aerogel layer. The VR layer provides tunable visible colors without compromising the low-emissivity property of the LEG layer, which achieves IR emissivity between 0.30 and 0.43. The ANF aerogel, reinforced with a grid structure, reduces thermal conduction, lowering IR radiation intensity by 40% at an 80 °C heat source. The composite exhibits effective electromagnetic interference (EMI) shielding and maintains multifunctional stability in strong acid, strong alkali, saline, and organic media. This design offers a novel strategy for environmentally robust multispectral camouflage materials suitable for extreme operational environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4192-y
Electrochemical water splitting is pivotal for scalable green hydrogen production, yet its practical deployment hinges on cost-effective electrocatalysts with high activity and durability. This study introduces a low-cost, three-dimensional (3D) nanoporous ZrVFeCoNi material fabricated via chemical dealloying, at merely 0.16% of the cost of Pt. The structure-activity relationship between its microstructure and hydrogen evolution reaction (HER) performance was systematically explored. Lattice defect effects from multiphase intermetallic compounds, combined with multi-metal synergy, optimize H+ adsorption energy and electron transfer kinetics. The 3D nanoporous architecture provides a high electrochemical surface area with abundant active sites, enhancing electrolyte penetration and reducing interfacial mass transfer resistance. Consequently, the ZrVFeCoNi electrode exhibits outstanding HER performance, requiring only a 38 mV overpotential to reach 10 mA cm−2 and maintaining stable operation for 1000 h at 500 mA cm−2. Integrated into a full water electrolyzer (ZrVFeCoNi || IrO2/Ni), the system achieves a cell voltage of 1.60 V at a current density of 400 mA cm−2. Advanced characterization and density functional theory (DFT) calculations reveal that interfacial interactions and charge transfer at heterointerfaces drive catalytic activity, showcasing the potential of 3D nano-structured multiphase intermetallic compounds as high-performance electrocatalysts for green hydrogen systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4322-4
Ultrafast scintillators with low-nanosecond emission are essential for next-generation high-rate X-ray and particle imaging. Although Ce3+-activated scintillators inherently exhibit fast response characteristics, conventional Ce3+-doped hosts rarely achieve low-nanosecond ultrafast decay. Here, we report a high-entropy fluoride scintillator (HEFS), Ce:LaGdCaSrBaF12 (Ce:LGCSB), in the form of bulk single crystals. The severe lattice distortion arising from multi-cation disorder induces exciton localization and effectively suppresses exciton diffusion. Through the rapid relaxation of localized excitons, the high-entropy Ce:LGCSB single crystals deliver a decay time of 1.23 ns with a 94.6% fast-component contribution and without any noticeable slow component. Through first-principles calculations, spectroscopic characterization, and transient dynamics analysis, we reveal that the ultrafast response originates from accelerated Frenkel exciton (FE) recombination enabled by the high-entropy environment. This work establishes entropy-engineered fluorides as promising ultrafast scintillator platforms and proposes a general strategy for extending sluggish diffusion effects to the excitonic scale, offering new opportunities for improving scintillation timing performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3596-2
High-entropy alloys (HEAs) have shown great promise in the CO2 reduction reaction (CO2RR) due to their tunable composition and unique physical and chemical properties. However, the role of HEAs in CO2RR and the underlying reaction mechanism remain underexplored, particularly through in situ techniques. In this work, we investigate the mechanism of CO2 reduction on AuAgCuPdPt HEAs using in situ Raman spectroscopy and attenuated total reflectance Fourier-transform infrared (ATR-FTIR) spectroscopy to reveal key intermediates and reaction pathways. Our results demonstrate that within the potential window of −0.2 to −0.7 V vs. reversible hydrogen electrode (RHE), the AuAgCuPdPt HEAs efficiently reduce CO2 to CO, achieving a Faradaic efficiency (FE) for CO greater than 90%, with a peak FE of 96.5% at −0.3 V vs. RHE. The CO2− intermediate was observed at low potentials, revealing the reaction pathway in the CO2 reduction process. Additionally, in situ ATR-FTIR results suggest that the introduction of an appropriate amount of Pt metal not only promotes water dissociation to generate protonic hydrogen, but also facilitates the desorption of *CO intermediates. The kinetic isotope effect of hydrogen-deuterium (H-D) confirms that water dissociation acts as a key proton donor in CO2RR. Furthermore, the catalyst of AuAgCuPdPt HEAs was applied as cathodes in a Zn-CO2 battery, achieving 90.23% FE for CO and a power density of 3.474 mW cm−2. This study provides new insights into the mechanistic understanding of CO2 reduction and underscores the importance of in situ spectroscopic techniques for advancing the design of efficient electrocatalysts for CO2 conversion.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3623-y
Organic light-emitting diodes (OLEDs) are an advanced technology for full-color displays, yet the low efficiency of blue OLEDs remains a critical bottleneck. Here, we report a new strategy to design robust Pt(II) emitters with enhanced molecular rigidity and increased locally excited character. The resulting Pt(II) emitter exhibits an extremely narrow emission spectrum peaking at 458.6 nm with a full-width at half-maximum (FWHM) of 16.0 nm and a small Huang-Rhys factor of 0.278, together with a high photoluminescence quantum efficiency of 95%. When doped into an OLED, the device emits at 464 nm with high color purity (FWHM = 19 nm) and achieves high external quantum efficiencies (EQEs) of 32.6%, 29.4%, and 26.9% at luminances of 123, 1000, and 5000 cd/m2, respectively. Notably, the device attains a record-high maximum brightness of 84,895 cd/m2 among reported deep-blue OLEDs with Commission Internationale de l'Éclairage (CIE) y-coordinate < 0.15. This work demonstrates one of the highest-performing deep-blue OLEDs reported to date, addressing the dual challenges of efficiency and brightness in this spectral region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3674-2
Enhancing catalytic activity is a core objective in catalyst design, with active site accessibility being a critical determinant. Polyoxometalate-based metal-organic complexes (POMOCs), combining advantages of POMs and MOCs, offer potential for constructing catalysts with highly accessible active sites. In this study, a series of POMOCs were synthesized using different POM templates: [CoII1.5(L)1.5(PMo12O40)(H2O)4]·3H2O (Co-PMo12), [CoII1.5(L)1.5(PW12O40)(H2O)4]·3H2O (Co-PW12), [CoII2(L)2(SiW12O40)(H2O)4]·11H2O (Co-SiW12), and H[CoII2.5(L)3(P2W18O62)(H2O)8]·10H2O (Co-P2W18). These were characterized by FT-IR, PXRD, and single-crystal X-ray diffraction. Catalytic activity differences for olefin epoxidation were attributed to distinct accessibility of Co(II) sites upon thermal activation. Notably, Co-P2W18 achieved 99% yield of 1,2-epoxycyclooctane within 3 hours at room temperature using O2 as oxidant, owing to highly accessible unsaturated Co(II) sites. This performance is superior to most reported catalysts. The reaction mechanism was investigated using density functional theory. The catalyst exhibited excellent stability over five cycles, with FT-IR, PXRD, and XPS confirming structural and oxidation state integrity. This work highlights the potential of POMOCs in designing catalysts with highly accessible active sites for enhanced catalytic activity.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506020
The rotary kiln roasting of lepidolite for lithium extraction faces challenges of unstable lithium conversion rates and high energy consumption. To address this, a multi-objective optimization method coupling improved neural network simulation with a multi-objective genetic algorithm was proposed, targeting the synergistic optimization of lithium conversion rate (TRLi) and natural gas consumption intensity (EIng). Using long-term industrial time-series data of batching parameters and kiln operating variables, back-propagation (BP) neural network and its particle swarm optimization (PSO) improved variant were developed to model TRLi and EIng. The PSO-BP model demonstrated superior accuracy in capturing the complex nonlinear relationships, reducing mean absolute percentage errors (MAPE) to 0.278 and 0.284 for TRLi and EIng, respectively. Subsequently, the non-dominated sorting genetic algorithm II (NSGA-II) was employed to construct a multi-objective optimization model, yielding a Pareto-optimal set of process parameters that maximize TRLi and minimize EIng. The results revealed that under NSGA-II optimized conditions, TRLi could be stabilized between 82.45% and 87.96%, an average increase of 3.61 percentage points over baseline operations, while EIng could be reduced to 53.7 m3 per ton of clinker. For an annual processing capacity of 3.2×105 tons of lepidolite concentrate and sulfate mixture, this corresponds to an additional 127.1 tons of lithium metal recovery, a reduction of 1,964,912 m3 in natural gas consumption, and a decrease of 3,763.84 tons in CO2 emissions annually. This study provides theoretical and technical support for the green, high-quality, and low-carbon supply of critical raw materials for the lithium battery new energy industry.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604026
Polycyclic aromatic hydrocarbons (PAHs) are persistent organic pollutants ubiquitously present in soils, posing severe risks to ecosystems and human health. This study synthesized MIL-88A(Fe) via a hydrothermal solvent method and applied it to the photocatalytic degradation of phenanthrene-pyrene (PHE-PYR) composite contaminants in soil, investigating the adsorption-photocatalytic synergy. Results demonstrated that adsorption of PHE-PYR onto MIL-88A(Fe) was dominated by physical and monolayer surface adsorption, with a maximum adsorption capacity of 97.25 mg/kg. This strong adsorption increased pollutant concentration near active sites, accelerating photocatalytic degradation. Under optimal conditions—3% catalyst dosage, 40% soil water content, 60 min visible light irradiation, initial pollutant concentration of 200 mg/kg, and acidic soil—the total degradation efficiency reached 79.20%. Photoelectrochemical characterization revealed significant visible-light response (200–600 nm), a narrow bandgap of 3.04 eV, and favorable band structure facilitating efficient electron-hole separation. Quenching experiments identified superoxide radicals (·O2−) and holes (h+) as primary reactive species. GC-MS analysis of intermediates indicated that PYR undergoes hydroxylation, oxidation, and ring-opening to form PHE, which is further hydroxylated and oxidized, ultimately mineralizing to CO2 and H2O. This work provides an efficient strategy for remediating PAH-contaminated soils.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508052
To improve the performance of pre-dust collectors in biomass boiler flue gas purification systems, a novel channel-steel baffle-type pre-dust collector was proposed to address the low collection efficiency of conventional designs. A gas-solid two-phase flow model was developed within the MP-PIC (multiphase particle-in-cell) framework and validated against physical experiments. The model simulated gas-particle motion inside the collector, systematically investigating the effects of structural modifications, flue gas conditions, and dust properties on collection efficiency and pressure drop. Results indicate that adding a flow baffle in the ash hopper and adopting an upper-inlet flue duct enhance collection efficiency with negligible impact on pressure drop. Flue gas velocity significantly influences performance: increasing velocity reduces efficiency while raising pressure drop; an optimal design velocity of 1.0–2.0 m·s−1 is recommended. Elevated flue gas temperature slightly decreases both efficiency and pressure drop, with minimal impact over a range of tens of degrees Celsius. Higher dust density and larger particle size improve collection efficiency and reduce pressure drop, whereas higher dust concentration increases both efficiency and pressure drop. The study elucidates the mechanisms by which structural and operational parameters affect pre-dust collector performance, providing theoretical guidance for designing low-resistance, high-efficiency collectors for biomass boilers.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025102002
The ultraviolet/chlorine (UV/Cl2) advanced oxidation process generates multiple radical species, enabling synergistic disinfection. However, the systematic influence of UV intensity on process performance remains inadequately characterized. This study investigated UV intensities from 0.25 to 2.0 mW·cm−2, assessing chlorine photolysis kinetics, bacterial inactivation, and disinfection by-product (DBP) formation. Results demonstrate that inactivation efficiency is not solely governed by total UV energy but is co-regulated by reaction kinetics and mass transfer. Increasing UV intensity accelerated chlorine photolysis by 33.7%–277.8%, elevating steady-state concentrations of hydroxyl radicals and chlorine radicals by factors of 1.6–3.8 and 1.3–3.2, respectively, thereby enhancing initial inactivation rates. However, higher intensities reduced cumulative chlorine exposure (CT value) to 14.3%–55.7% of baseline, causing overall inactivation to first increase then decrease. At a fixed UV dose of 150 mJ·cm−2, an intensity of 1.0 mW·cm−2 achieved optimal 6.5-log inactivation of Escherichia coli and the lowest bacterial reactivation rate (0.07%). Common water constituents (HCO3−, Cl−, natural organic matter) inhibited disinfection, with natural organic matter exerting the strongest suppression (2.7-log reduction). Notably, 1.0 mW·cm−2 exhibited the greatest resistance to interference. Elevated intensity reduced total organic halogen formation from 33.7 μg·L−1 to 19.0 μg·L−1. Balancing disinfection efficacy and DBP risk, 1.0 mW·cm−2 is identified as the optimal UV intensity for the UV/Cl2 process in sand-filtered water treatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3766-0
Leuco dye-based thermochromic fibers suffer from poor light fastness, limiting their cyclability. Here, a hydrogen bond dissociation/structural isomerization-based dual ultraviolet (UV)-shielding strategy is proposed to develop enhanced light-resistant thermochromic elastomer fibers (Azo/TCM@Abs/TPU) employing UV absorbers and 4-dodecyloxyazobenzene (C12-Azo) through a coaxial wet-spinning process. The integration of UV absorbers and C12-Azo enhances UV protection, effectively blocking nearly the entire UV spectrum. The light fastness of Azo/TCM@Abs/TPU has been improved to Grades 3–4, enabling a stable thermochromic function to withstand several months of sunlight exposure. Additionally, the absorbed UV light is stored as chemical energy within C12-Azo via trans-to-cis photoisomerization. This stored energy can be released as heat on demand. The coaxial dual-protection concept using photoisomerization offers an efficient method to enhance light resistance in thermochromic fibers.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509039
Under the dual-carbon strategic goal, China's wind power installed capacity continues to grow rapidly, making the low-carbon recycling of decommissioned wind turbine blades increasingly prominent. This study systematically reviews material recovery pathways, policy support systems, and life-cycle carbon benefits of decommissioned blades. It first analyzes regional distribution and unit characteristics of wind power installations, identifying differentiated challenges in dismantling, transportation, and reuse across regions. Subsequently, it compares mechanical/physical, pyrolysis, chemical, and combined recycling technologies. Results show that mechanical/physical methods are low-cost but yield fiber retention rates of only 10%–78%; pyrolysis has reached industrial scale but exhibits high carbon emission intensity; chemical methods achieve higher fiber retention (55%–96%) with potential carbon reduction advantages; combined methods overcome single-technology limitations, achieving fiber retention exceeding 95%, demonstrating potential for high-value utilization and low-carbonization. At the policy level, China has proposed a two-stage target: initially establishing a blade recycling responsibility mechanism by 2025 and forming industrial clusters by 2030, with gradual improvements in standards and incentives. Life-cycle assessment indicates that wind power has slightly higher global warming potential (GWP) than photovoltaics, but its emissions are mainly concentrated in component manufacturing; if efficient recycling is achieved, wind power could surpass photovoltaics in full life-cycle carbon benefits. In summary, promoting efficient recycling and policy coordination for decommissioned wind turbine blades can achieve dual benefits of resource recycling and carbon reduction, providing strong support for reconstructing a sustainable renewable energy development paradigm.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606014
Microplastics, as emerging environmental pollutants, can adsorb psychotropic drugs in aquatic environments, facilitating their migration and transformation, ultimately posing ecological risks. This study investigated the adsorption behavior and mechanisms of four common microplastics—polyethylene (PE), polypropylene (PP), polystyrene (PS), and polyvinyl chloride (PVC)—each with a particle size of 50 μm, toward three psychoactive drugs: diazepam, fluoxetine, and mianserin. Adsorption kinetics, isotherms, and the effects of pH and salinity were examined. Kinetic data fitted well to a pseudo-second-order model, indicating chemisorption as the rate-limiting step. Isotherm analysis using Langmuir and Freundlich models revealed that PE exhibited the highest affinity for fluoxetine, PP for mianserin, and PVC for diazepam, while PS showed linear adsorption for fluoxetine, suggesting partitioning. The adsorption of diazepam was maximal at pH 6.5–8.5, typical of natural surface waters, and increased with NaCl concentration, indicating that non-electrostatic interactions dominate and that higher ionic strength enhances adsorption. Mechanistic insights suggest that hydrophobic interactions, hydrogen bonding, π-π interactions (for PS), and halogen bonding (for fluoxetine) contribute to adsorption. These findings highlight the potential of microplastics to act as vectors for psychoactive drugs, necessitating further research on their environmental fate and ecological implications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3851-3
Aqueous zinc-ion batteries (AZIBs) face critical challenges from zinc anode instability, including corrosion, hydrogen evolution reaction (HER), parasitic byproduct formation, and uncontrolled dendrite growth. To address these issues, we developed a multifunctional cerium-based metal-organic framework (Ce-MOF) coating for zinc anodes. The coating features an ordered porous structure and inherent properties that mitigate HER, suppress side reactions, and inhibit dendrite formation. Symmetric cells using Ce-MOF/Zn demonstrated exceptional cycling stability for over 2060 h at 0.5 mA cm−2 with a low hysteresis polarization of 26 mV. In full cells with an I2@AC cathode, the Ce-MOF/Zn||I2@AC achieved outstanding cycling stability of 28,550 cycles at 5 A g−1, with 91% capacity retention (109.6 mAh g−1). Through integrated characterization employing in-situ optical microscopy, ex-situ XRD, SEM, and DFT calculations, we elucidated the multifunctional mechanism: the Ce-MOF coating facilitates preferential (002)-oriented Zn deposition to suppress dendrites, reduces Zn2+ desolvation energy to enhance deposition kinetics, and modulates interfacial chemistry to mitigate HER and corrosion. This work establishes Ce-MOF coatings as a simple yet powerful strategy for developing high-performance zinc anodes, providing critical insights for advancing practical AZIB technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3904-6
Disrupting calcium ions (Ca2+) homeostasis to induce calcium overloading has emerged as a promising strategy for cancer therapy. However, calcium overloading based on exogenous calcium salts (such as calcium carbonate and calcium peroxide) can easily lead to off-target Ca2+ release, causing severe side effects such as hypercalcemia and cardiac or renal dysfunction. This review explores the calcium-free nanomaterials for mediating targeted calcium dysregulation in tumors. These nanomaterials function not by carrying Ca2+ but by precisely regulating endogenous calcium signaling pathways. They promote massive Ca2+ influx through targeted activation of calcium channels and/or inhibit Ca2+ efflux by suppressing pumps, effectively triggering intracellular calcium accumulation. Such a strategy efficiently induces mitochondrial dysfunction, endoplasmic reticulum stress, and immunogenic cell death, thereby inhibiting tumor growth and metastasis while potentiating antitumor immunity. We systematically summarize the design principles, mechanisms of action, and therapeutic applications of these calcium-free nanoplatforms, highlighting their potential to overcome the limitations of traditional therapies and boost ion-interference-based cancer treatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4162-0
The urea oxidation reaction (UOR) offers a low-energy pathway for hydrogen production via water electrolysis, but Ni-based catalysts suffer from Ni self-oxidation reaction (NSOR) that wastes energy and poisons active sites via strong CO2 adsorption. Here, we design MoN/Ni heterostructures to optimize the electronic structure of Ni sites, suppressing NSOR. X-ray photoelectron spectroscopy and X-ray absorption spectroscopy confirm the formation of electron-rich Mo and electron-deficient Ni active pairs. In-situ spectroscopy, electrochemical tests, and density functional theory calculations reveal that electron-rich Mo sites enhance urea adsorption, while electron-deficient Ni sites prevent NSOR, facilitating urea activation, intermediate conversion, and CO2 desorption. The synergistic effect yields a current density of 100 mA cm−2 at only 1.39 V vs. RHE in 1 M KOH + 0.33 M urea, outperforming many NiOOH-based catalysts. This work introduces a novel high-performance catalyst with electron-rich/electron-deficient active pairs for efficient UOR.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4096-7
Hexagonal boron nitride (h-BN) nanomaterials exhibit exceptional properties but suffer from severe aggregation due to undesirable surface characteristics, limiting their application in polymer nanocomposites. Existing covalent functionalization methods often compromise between time efficiency, energy consumption, and structural integrity. This study presents a rapid, room-temperature catalytic grafting strategy using tris(pentafluorophenyl)borane (B(C6F5)3) to functionalize h-BN nanoflakes bearing edge hydroxyl groups. The reaction between B–OH groups and activated Si–H bonds of hydrosilanes proceeds under mild conditions, preserving the structural integrity of h-BN. Density functional theory (DFT) calculations confirm the catalytic feasibility and elucidate two possible reaction pathways: backside-attack and flank-attack mechanisms. The modified h-BN exhibits significantly improved dispersibility in low-polarity solvents and tunable surface properties. This efficient method offers a versatile platform for h-BN surface engineering, facilitating broader practical applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4163-y
Liquid metals (LMs) are promising catalyst systems due to their unique interfacial properties, yet migration and aggregation of active species cause performance degradation. Here, we report a composition optimization strategy using a Ga-In eutectic liquid metal support to reduce surface energy and achieve homogeneous incorporation of Cu species (GaIn-Cu). Comprehensive characterizations confirm uniform Cu dispersion, which inhibits migration and formation of CuGa2 intermetallic phases during CO2 electroreduction (CO2RR). The GaIn-10-Cu catalyst achieves a maximum CH4 Faradaic efficiency of 73.49% at -0.8 V vs. RHE, significantly higher than Ga-Cu (61.49%). Moreover, GaIn-10-Cu exhibits enhanced stability for CH4 generation over 40 h of continuous operation. In-situ spectroscopic studies reveal that GaIn-10-Cu favors formation and protonation of key *CHO and *OCH3 intermediates, steering selectivity toward CH4. This work demonstrates that tuning LM composition modulates catalytic site performance, offering a strategy for durable and selective LM-based electrocatalysts.