SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4472-0
Dynamic electrocardiography (ECG) monitoring during physical activity remains compromised by motion artifacts that corrupt signal fidelity, particularly with conventional gel electrodes whose impedance rises sharply under deformation. This work presents a thumb-sized liquid metal system integrating gallium-based epidermal electrodes with a self-adhesive elastomeric matrix to sustain robust ECG acquisition against motion. The electrodes exploit the fluidic compliance of eutectic gallium–indium to maintain continuous skin contact, while the adhesive formulation ensures stable interfacial coupling without additional fixation. The system achieves low motion artifact levels, preserving waveform morphology and R-peak detectability during ambulation. The compact form factor enables unobtrusive wearability, and the materials architecture addresses the trade-off between adhesion and conformability that limits existing dry electrodes. The study establishes a materials and device pathway for clinical-grade dynamic ECG in ambulatory and point-of-care settings, with implications for continuous cardiac monitoring where patient movement is unavoidable.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4404-7
Electrochemical propylene epoxidation offers a sustainable route to propylene oxide (PO), but achieving high selectivity and stability under industrial current densities remains challenging. Herein, we report a high entropy amorphous CoFeNiCrMnBOx borate loaded with high valence Pt single atoms catalyst (a-Pt-HEBO) for stable bromine radical-mediated propylene epoxidation reaction (BrPOR). The high-entropy amorphous structure reshapes the interfacial hydrogen-bonding network and enriches free water, substantially lowering the energy barrier for water dissociation. Meanwhile, the strong electronic interactions between the coordinatively unsaturated, high-valence single Pt atoms and the substrate effectively prevent transition metal dissolution at high anodic potentials. The catalyst achieved 82.1% Faraday efficiency of PO at an industrial grade current density of 100 mA cm-2, and demonstrated excellent industrial application stability in up to 500 h of continuous test and within a scaled-up electrolyzer (4 × 4 cm2). This work provides a design for high-entropy catalysts in halogen-mediated electrosynthesis and a viable pathway toward carbon-neutral PO production.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4275-3
Electrochemical in-situ production of active chlorine (AC) via chlorine evolution reaction (CER) can alleviate hull corrosion and residual chlorine overage, which is a highly reliable disinfectant for sewage and ballast water. Nonetheless, the primarily competitive oxygen evolution reaction and gradual anode passivation hinder its practical application. Herein, we employed the in-situ hydrothermal strategy to synthesize Ru/TiO2-x to realize high activity and selectivity of CER. The robust interaction of Ru sites and TiO2-x achieved via a one-step hydrothermal synthesis strategy, the structural and valence state characterizations confirm that Ti3+ stabilizes Ru solely in the metallic state (Ru0) via structural confinement effects, effectively inhibiting catalyst oxidation. As a result, the Ru/TiO2-x requires only an overpotential of 33 mV to reach 10 mA cm−2, and possess strong catalytic durability, sustaining continuous operation for 100 h with negligible current decay. Further integration with a triboelectric nanogenerators successfully realizes the generation of AC, which demonstrates a >99.9% inactivation efficiency against Escherichia coli in simulated seawater environments, while also effectively degrading ammonia nitrogen and urea contaminants in domestic wastewater.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4159-y
The electrocatalytic oxidation of ethylene glycol (EG) derived from polyethylene terephthalate (PET) waste to valuable glycolic acid (GA) represents an attractive route for waste resource upcycling. However, achieving high selectivity remains challenging due to the difficulty in steering the complex reaction pathway. In this study, PdPtCuInBi high-entropy intermetallic metallene (HEI-PdPtCuInBiene) is reported to precisely control EG oxidation reaction (EGOR) pathway for GA production by constructing multiple active sites at the atomic scale. In PET hydrolysate, it achieves a Faradaic efficiency of 99.87% and a production rate of 1.47 mmol h−1 cm−2, along with excellent stability. Mechanistic studies reveal that the high-entropy structure induces strong p-d orbital hybridization, which optimizes the electronic structure of active sites, thus weakening the adsorption of key carbonyl intermediates and suppressing C–C bond cleavage. The synergistic electronic effect among Pd, Pt, and Cu further enables differential adsorption of distinct intermediates on diverse active sites, enhancing the selective formation of GA. Techno-economic analysis exhibits high profitability (~$784.9 t−1 PET) of this route, demonstrating the great potential of high-entropy intermetallic metallene in regulating electrocatalytic upcycling of PET waste and beyond.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3841-6
Ni-rich layered oxide cathodes are pivotal candidates for next-generation lithium-ion batteries (LIBs) due to their high capacity and energy density. However, their susceptibility to structural deterioration and interfacial degradation during cycling causes substantial capacity fade, hindering commercialization. This work proposes a synergistic strategy of lattice doping and in situ surface coating to enhance structural integrity and interfacial stability of LiNi0.9Co0.05Mn0.05O2. La and Y dopants act as pillars to reinforce the layered structure, mitigating volume changes and expanding c-axis spacing to facilitate Li+ diffusion. Concurrently, La4NiLiO8 and LiYO2 coatings protect the cathode from H2O/CO2 corrosion and electrolyte attack, while their high lithium-ion conductivity promotes Li+ transport. The modified cathode delivers exceptional electrochemical metrics: high specific capacity of 207.3 mA h g−1, remarkable cycling stability with 97.6% retention after 100 cycles, superior rate capability of 152.1 mA h g−1 at 10.0 C, and enhanced thermal stability. This work establishes a paradigm for multi-dimensional stabilization of Ni-rich cathodes via synergistic bulk and interface engineering, providing insights for designing high-performance energy storage systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3637-6
Traditional optical fiber communication encryption methods lack sufficient dynamic adaptability and hardware flexibility, while reconfigurable logic gates can overcome this limitation, thereby significantly improving the flexibility of encryption systems. This study reports a reconfigurable optoelectronic logic gate (OELG) system based on hafnium-zirconium oxide (HZO) ferroelectric thin films. Through ultra-low temperature atomic layer deposition technique, the fabricated HZO thin films demonstrate an exceptional pyroelectric coefficient of 1835.91 μC m−2 K−1 and robust multi-level polarization stability, enabling efficient broadband photon-to-current conversion. By leveraging the pyroelectric effect and tunable polarization states, the OELG device achieves dynamic optical signal modulation and logic processing. The OELG device supports five fundamental logic operations (AND, OR, NAND, NOR, NOT) via electrical bias and polarization control, without requiring hardware modifications. The OELG device demonstrates stable performance over 10^9 cycles with no degradation, meeting practical application requirements. Furthermore, a convolutional neural network (CNN)-integrated image encryption-decryption framework was validated, achieving 95.01% recognition accuracy on decrypted data, while unauthorized decryption attempts resulted in significant feature loss. This study addresses security challenges in optical communication networks by proposing an innovative solution that integrates pyroelectric materials with reconfigurable logic gate technology, offering a new pathway to enhance physical-layer security.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3713-y
Layered double hydroxides (LDHs) are promising electrocatalysts for the oxygen evolution reaction (OER), yet their practical application remains limited by poor electrical conductivity and sluggish reaction kinetics. In this work, we synthesize three high-entropy LDHs (HELDHs) featuring a hierarchical architecture of microspheres assembled from ultrathin nanosheets, via a simple hydrothermal method using a combination of low-cost, catalytically active transition metals (Fe, Co, Ni, Mn, Zn, Cu, and Cr). Among them, the FeCoNiMnZn HELDH exhibits outstanding OER performance, requiring an overpotential of only 306 mV to reach a current density of 100 mA cm−2. Notably, during 200 h of continuous operation, the device exhibits a stable and, in some cases, increasing current output. This exceptional activity is attributed to the formation of abundant cation vacancies, induced by Zn leaching, which enhance the intrinsic catalytic properties by optimizing the adsorption energies of key OER intermediates. Density functional theory calculations further validate that these vacancies modulate the electronic structure and lower reaction barriers, underscoring the effectiveness of cation-vacancy engineering in high-entropy systems for efficient and durable water oxidation catalysis. The optimized catalyst was further evaluated as the air cathode in a zinc–air battery, demonstrating practical electrochemical performance.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.3724/2097-213X.2025.JFCT.0021
Red mud, an industrial solid waste from alumina production, poses severe environmental challenges. This study presents a resource-efficient strategy to convert red mud into high-performance microwave absorbing materials. FexOy/TiO2/C composites were synthesized via a sol-gel method using starch as carbon source, followed by carbothermal reduction. The phase composition and microstructure were optimized by adjusting calcination temperature and raw material ratio. The optimal sample, RmCT-5.4-700, exhibited a minimum reflection loss (RLmin) of -30.2 dB at 14.0 GHz with an effective absorption bandwidth (EAB) of 5.3 GHz at a coating thickness of 2.0 mm. The superior absorption performance is attributed to the synergistic effects of dielectric components (TiO2, graphitized carbon) and magnetic components (Fe3O4/Fe). Carbothermal reduction introduces defects that induce dipole polarization, while the conductive network formed by graphitized carbon and Fe3O4/Fe particles enhances conductive loss. Heterogeneous interfaces between Fe3O4, Fe, TiO2, and the red mud matrix promote interfacial polarization. The magnetic loss of Fe3O4/Fe improves impedance matching, facilitating electromagnetic wave penetration and absorption. This work not only provides a novel route for red mud valorization but also contributes to the high-value utilization of solid wastes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3545-7
Magnetically driven hydrogel robots show promise in biomedical and underwater applications due to remote controllability, flexibility, biocompatibility, and chemical stability. However, limited functional integration restricts their adaptability. Here, a universal modular assembly strategy is introduced using a self-healing κ-carrageenan/polyacrylamide hydrogel embedded with magnetic particles, enabling free assembly of magnetic actuation modules. These modules construct soft robots with complex geometries and magnetization distributions, allowing diverse deformations under magnetic fields. The strategy further integrates photocatalysis by embedding Ru-Bi2CrO6 photocatalysts into functional modules, yielding an oxygen-generating robot. This robot exhibits flexible underwater movement via magnetically controlled oscillatory actuation, minimizing water agitation while supplying stable oxygen to specific aquatic environments. The photocatalytic oxygen evolution rate reaches 389.1 μmol g−1 h−1. The hydrogel skeleton suppresses particle aggregation and sedimentation, and facilitates magnetic recovery. This scalable and adaptable approach advances multifunctional soft robot design.
The Chinese Journal of Process Engineering•2026•DOI: 10.12034/j.issn.1009-606X.225250
Slag foaming is a critical phenomenon in electric arc furnace (EAF) steelmaking, enhancing thermal efficiency, suppressing metal splashing, and stabilizing the refining process. Accurate prediction and control of slag foaming are essential for green and efficient steelmaking. This review systematically examines research progress on slag foaming prediction, clarifying the applicability, advantages, and limitations of different predictive methods to support intelligent control of foamy slags. Following the framework of 'influencing factors-prediction methods-development trends', the study summarizes the coupling effects of multiple variables such as basicity, viscosity, surface tension, suspended particles, gas parameters, and temperature on foam formation and stability. It compares five major prediction approaches: empirical formulas, dimensionless modeling, thermodynamic calculations, computational fluid dynamics (CFD) simulations, and machine learning models, analyzing their core concepts, merits, and constraints. Results indicate that single models often struggle to balance real-time capability and accuracy, particularly under multi-variable coupling and complex operating conditions. Therefore, a hybrid prediction framework combining mechanism-based and data-driven models is proposed, emphasizing physical constraints, multi-scale coupling, and multi-source data fusion. This integrated approach is expected to advance slag foaming prediction from 'computable' to 'controllable and adjustable', offering methodological insights for the development of green and intelligent EAF steelmaking.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025022501
The pretreatment of trace emerging contaminants in environmental matrices is challenging due to diverse methods and uncertain applicability. This study compared solid-phase extraction (SPE) and liquid-liquid extraction (LLE) for extracting endocrine-disrupting compounds (EDCs), particularly phthalate esters (PAEs), using laboratory-spiked blank samples. LLE achieved satisfactory recoveries for PAEs at spike levels below 4 μg·L−1, enabling detection of five PAEs including diisodecyl phthalate (DIDP), with improved efficiency via repeated extraction. SPE offered lower detection and quantification limits, higher accuracy and sensitivity, and achieved high recoveries for 12 EDCs and 10 antibiotics at spike levels ≥0.2 μg·L−1, with detection limits as low as 0.1–6.4 ng·L−1. The developed SPE coupled with liquid chromatography-Orbitrap mass spectrometry (LC-Orbitrap MS) method was applied to industrial wastewater samples. Across five industrial sectors (coatings, rubber, pharmaceuticals, inks, and materials technology), five antibiotics and ten EDCs were detected, with total concentrations ranging from 0.03–0.56 μg·L−1 and 0.07–1.91 μg·L−1, respectively. Sector-specific profiles emerged: rubber industry effluent was dominated by dibutyl phthalate (DBP) at 1.07 μg·L−1, while pharmaceutical effluent featured sulfamonomethoxine (SMM) at 0.34 μg·L−1. This systematic evaluation demonstrates that SPE-LC-Orbitrap MS is robust for complex matrices, providing a technical foundation for accurate quantification of emerging contaminants in industrial wastewater.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-3961-8
This correction addresses an inadvertent misplacement of Fig. 4b3 during figure reorganization in the original article published in Science China Materials, volume 65, issue 10, 2022, page 2850 (DOI: 10.1007/s40843-022-2024-6). The corrected Fig. 4b is presented herein. The authors confirm that this correction does not affect the results, conclusions, text, or figure caption of the original work. The correction was requested by the authors and received on 6 January 2026, accepted on 8 January 2026, and published online on 10 February 2026. The original study introduced flexible electrostatic hydrogels derived from marine organisms for nitric oxide-enhanced photodynamic therapy against multidrug-resistant bacterial infections. The correction ensures the accurate representation of experimental data, maintaining the integrity of the scientific record.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60659-7
Coal gasification fine slag (CGFS), a solid waste from entrained-flow coal gasification, is characterized by fine particles and high silicon and aluminum content. This study proposes a simple and economical hydrothermal synthesis of ZSM-5 molecular sieve using CGFS as raw material. Impurities were removed by acid washing, followed by alkaline extraction of silicon and aluminum species. The extracted Si-Al precursors were crystallized hydrothermally at 170 °C for 48 h, yielding ZSM-5 with a high specific surface area of 358 m2/g. Adsorption experiments showed that the synthesized ZSM-5 exhibited excellent Pb2+ removal performance: at 25 °C, the removal efficiency for a 50 mg/L Pb2+ solution reached 83.7%, with an adsorption capacity of 104.625 mg/g under optimized conditions. The adsorption process is mainly governed by chemisorption mechanisms, including surface complexation, precipitation, and ion exchange. Thermodynamic analyses indicated that Pb2+ adsorption is spontaneous and endothermic, consistent with multilayer chemisorption. The synthesized ZSM-5 shows promising potential for application in the treatment of lead-containing wastewater, offering a high-value utilization route for coal-based solid waste.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202408057
Urban waterlogging, exacerbated by climate change and rapid urbanization, poses increasing risks, particularly in coastal low-lying areas with dense river networks. This study simulated waterlogging in the Shajing River drainage area of the Maozhou River basin, Shenzhen, using the SOBEK hydrodynamic model. Under a 5-year return period rainfall, 47 manholes overflowed and 31.29% of stormwater pipes operated at full capacity. Twelve waterlogging-prone points were identified: eight due to insufficient drainage capacity and five due to river backflow from low elevation. Two optimization schemes were compared: enlarging pipe diameters and implementing Low Impact Development (LID) measures. Pipe enlargement reduced overflowing manholes by 32 and full-flow pipe length by 20%, effectively decreasing surface ponding. LID measures reduced overflowing manholes by only 4 and full-flow pipe length by 1.5%, but decreased maximum flooding depth by nearly 1 m, alleviating drainage system burden. The study highlights the complex causes of coastal urban waterlogging, especially river backflow under tidal influence, and recommends considering sea-level rise and storm surge in drainage design. The findings provide valuable references for attributing waterlogging causes and planning drainage network upgrades in coastal cities.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4015-5
Mechanochromic photonic crystals are promising for smart optical materials due to their tunable photonic stop band. Here, we report interface-engineered transparent and mechanochromic non-close-packed photonic crystals (NPCs) by incorporating polystyrene@vinyl-modified SiO2 (PS@V-SiO2) nanospheres (n_PS=1.59, n_V-SiO2=1.46) into a photocurable phenoxypolyethylene glycol acrylate (PEGPEA) matrix (n_PEGPEA=1.52). The nanospheres formed solvation-mediated liquid NPCs in the precursor. Ultraviolet (UV) curing promoted copolymerization between surface C=C bonds of nanospheres and the matrix, which reduced interfacial scattering and enabled highly transparent NPC films. Meanwhile, non-uniform polymer shrinkage led to variations in the ordering of nanospheres, especially in structures with a low volume fraction (φ ≤ 0.23). Under external strain (ε: 0–64%), the film exhibited a dynamic color response. Initially, stretching enhanced the ordering of the nanospheres and the reflection intensity of NPCs, thereby activating the structural color. Further deformation, however, introduced defects and reduced the reflectivity. A blue shift of ~213 nm was achieved in an NPC (φ = 0.23) fabricated by 170 nm of PS@V-SiO2 nanospheres, accompanied by a color gradient from red to blue. Comparisons across SiO2–poly(ethylene glycol) diacrylate (PEGDA, n_PEGDA=1.45), SiO2–PEGPEA, and PS@V-SiO2–PEGDA NPC systems highlighted the key role of interfacial scattering, which is affected by the synergistic effects of interfacial covalent polymerization, refractive index matching between the elastomer matrix and nanospheres, and the crosslinking density. This work demonstrates spectrally tunable mechanochromism via size control and patterned anti-counterfeiting labels, thereby providing insights for designing advanced anti-counterfeiting materials applicable in flexible electronics and displays.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4045-x
The release of radioactive iodine from nuclear accidents and nuclear medicine poses significant environmental and health risks. Here, we report the design and synthesis of two cross-linked macrocycle-based porous organic polymers (P1 and P2) with different functionalities for efficient and rapid capture of radioactive iodine. P1 achieves complete iodine adsorption within 5 minutes, with an exceptional adsorption rate constant (k_obs) of 18.92 g g−1 min−1 (8.24 g g−1 min−1 for P2), representing a record-high iodine removal rate among state-of-the-art porous organic polymers. P1 demonstrates superior iodine adsorption efficacy in dynamic flow-through experiments, achieving a remarkable efficiency of 96.4% for radioactive 131I removal, greatly minimizing radiation contamination. Experimental and modelling techniques reveal that the superior iodine adsorption performance originates from electron-rich functional groups, hydrophobic surface, and porous structure of P1, thus exhibiting remarkable iodine capture capabilities through charge transfer, halogen bonding, and hydrophobic effects. The adsorbents show excellent stability and performance under complex and harsh conditions (pH 2–10) and can be easily regenerated, confirming their excellent reusability and potential for practical applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4085-9
Bone defects remain a prevalent clinical challenge, and regenerative medicine based on bone tissue engineering offers promising solutions. Traditional osteogenic materials rely on bioactive macromolecules like growth factors, which suffer from poor stability and stringent storage requirements. From a structural perspective, bone tissue resides in a phosphorylated microenvironment, with 65–70% of inorganic components composed of hydroxyapatite. Inorganic phosphorylated materials induce osteogenic differentiation but exhibit high stiffness, brittleness, slow degradation, and limited mechanical tunability. Synthetic phosphorylated polymers with excellent mechanical properties and biocompatibility have been developed to address these issues. In this work, we developed a series of phosphorylated polymers derived from poly(glycerol sebacate) (PGS), a biocompatible and biodegradable material. Leveraging the hydroxyl-rich backbone of PGS, we demonstrated an efficient method for controllable phosphorylation of PGS side chains, enabling synthesis of PGS-based phosphorylated (PGS-P) polymers with tunable phosphorus contents. The optimized phosphorylated polyester, PGS-P4, exhibited strong ability to promote osteogenic differentiation of rat BMSCs, and its porous three-dimensional scaffolds showed favorable properties for bone regeneration. BMSCs cultured for one week and observed by fluorescence microscopy showed enhanced BSP protein expression on PGS-P2, PGS-P4, and PGS-P6 groups compared with PLGA and PGS, with PGS-P4 displaying the most intense signal. In summary, we present a simple and controllable method for preparation of functionalized polyesters and their porous scaffolds with tunable phosphorus content, validating its effectiveness in promoting osteogenic differentiation of rat BMSCs. All phosphorylated polyesters exhibit enhanced differentiation-promoting effects compared to non-phosphorylated PGS; however, the degree of enhancement does not increase monotonically with phosphorus content. PGS-P4, containing an optimal phosphorus level, shows the most pronounced biological functions.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4123-0
Aqueous aluminum-ion batteries (AAIBs) are promising for large-scale energy storage due to safety, sustainability, and theoretical high capacity. However, sluggish electron/ion transport in conventional cathodes limits rate capability. Here, we first propose high-entropy engineering of metal oxides (HEOs) as cathodes in AAIBs, leveraging the 'cocktail effect' and abundant electron transport pathways to enhance rate-capacity. Atomic-level interactions between different metal atoms broaden the d-band with reduced electronic level degeneracy, facilitating rapid electron transport, achieving one of the best rate capabilities (119.4 mAh g−1 at 10.0 A g−1) among metal-oxide cathodes. The disordered layered oxides formed with a high-entropy framework alleviate electrostatic repulsion between aluminum ions and the fixed lattice, mitigating structural degradation and imparting excellent cycling stability (over 95.1 mAh g−1 after 500 cycles at 2.0 A g−1). The optimized HEO-Cr cathode (Fe0.6Co0.6Ni0.6Mn0.6Cr0.6O4) exhibits outstanding rate performance and cycling stability. DFT simulations and electrochemical tests reveal that multi-transition metal incorporation, bandgap narrowing, and unique lattice structure drastically enhance electron transport efficiency. The layered phase formed after cycling, based on a high-entropy framework, overcomes challenges from high charge density aluminum ions, significantly enhancing cycling stability. This work paves the way for high-performance AAIBs and other aqueous multivalent metal ion batteries by rationally designing high-entropy engineering.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4129-y
Therapeutic biosynthesis is a promising strategy for precision cancer therapy, yet achieving controlled synthesis of abiotic materials within tumors remains challenging. Here, we report a “dual lock-and-key” system for tumor-specific intracellular synthesis. The precursor, termed “dual-lock,” is activated by two endogenously overexpressed enzymes—azoreductase (AzoR) and nitroreductase (NTR)—acting as “dual keys” in target cancer cells. This activation triggers a condensation reaction that produces fibrous mesh covalent organic polymers (Fm-COPs) in situ. Synthesized Fm-COPs effectively disrupt the cytoskeleton, inhibiting cell migration and invasion while inducing apoptosis. In vivo studies demonstrate that this strategy achieves specific tumor enrichment and deep penetration, leading to significant tumor growth inhibition (tumor inhibition rate >70%) without systemic toxicity, as evidenced by stable body weights and normal histopathology. The dual enzyme-responsive mechanism ensures high selectivity, and the small-molecule precursors facilitate efficient tumor penetration. This work presents a next-generation approach for high-precision cancer therapy, offering a biocompatible and autonomous strategy for intracellular synthesis.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3631-1
Anion exchange membrane water electrolysis (AEMWE) offers cost and dynamic-response advantages over proton exchange membrane systems, yet commercial deployment is constrained by the alkaline stability of anion exchange membranes (AEMs) and the sluggish kinetics of non-precious metal catalysts. This work reports a series of poly(terphenyl-diphenylmethane piperidinium) (QPDPMTP) membranes synthesized with varied diphenylmethane (DPM) content. The alkyl chain of DPM induces pronounced microphase separation and elevates free volume fraction, yielding an OH− conductivity of 152 mS cm−1 at 80 °C for QPDPMTP-10. After 1032 h immersion in 6 M NaOH at 80 °C, the membrane retains 90.7% of its initial conductivity. An AEMWE cell integrating QPDPMTP-10 with a non-precious NiFeCo LDH/NiS/NF anode achieves 3.11 A cm−2 at 2 V in 1 M KOH at 80 °C and sustains 1 A cm−2 for 1800 h under gradient KOH concentration. These results establish a viable pathway for durable, low-cost AEMWE systems.