SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4342-3
Electron acceptors containing single-bond-linked building blocks offer attractive advantages for organic solar cells owing to their synthetic simplicity and structural modularity. However, achieving backbone planarity without compromising electronic compatibility remains a persistent challenge. Conventional conformational locking strategies based on alkoxy substitution can effectively suppress torsional freedom but often elevate the highest occupied molecular orbital energy level, limiting compatibility with widely used donor polymers. Here, we report a partially fused electron acceptor design that achieves intrinsic backbone planarity through heterocycle selection rather than side-chain-assisted conformational locking. By incorporating a benzodifuran core and furan-thiophene linkages, the resulting acceptors exhibit a near-coplanar backbone geometry as revealed by density functional theory calculations, without the need for electronically perturbing alkoxy groups. Devices based on the optimized acceptor (BDF-1) deliver a binary power conversion efficiency of 12.2%, and further improvement to 19.5% is achieved in a ternary blend with PM6 and BTP-eC9. The enhanced performance is accompanied by favorable morphology, balanced charge transport, and suppressed recombination losses. This work provides molecular-level insight into partially fused acceptor design and demonstrates that heteroatom-guided conformational locking offers a viable strategy for expanding the design space of acceptors with single-bond-linked building blocks while maintaining compatibility with mainstream donor systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4176-y
Three-photon microscopy (3PM) in the near-infrared-III (NIR-III) window (1600–1840 nm) enables high-resolution visualization of cerebral vasculature in vivo, but its imaging depth and quality are limited by the performance of fluorescent probes. Here, we report a probe optimization strategy transitioning from mirror symmetry to centrosymmetry, yielding a highly symmetric aggregation-induced emission (AIE) molecule, T4PQ. The centrosymmetric structure aligns donor-acceptor units, promoting uniform electron cloud delocalization and directional charge transfer, which enhances exciton formation and suppresses non-radiative decay, thereby increasing fluorescence quantum yield. This symmetry also boosts the three-photon absorption cross-section by enhancing electron delocalization and transition dipole moment, enabling stronger nonlinear optical responses under long-wavelength excitation. T4PQ nanoparticles (T4PQ NPs) exhibit an enhanced three-photon absorption cross-section, high fluorescence quantum yield, and excellent photostability. In murine models, T4PQ NPs achieved three-dimensional cerebrovascular imaging at a depth of 1785 μm and real-time hemodynamic observation in microvessels at 1006 μm depth, with good biocompatibility. These results validate the advantage of centrosymmetric molecular design for deep-brain imaging probes, offering a high-performance tool for neurovascular research.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3604-1
Piezoelectric materials convert mechanical energy into electrical signals, enabling applications in sensors, actuators, and energy harvesting. Inorganic ceramics like PZT and BTO exhibit excellent piezoelectric properties but are brittle, limiting their use in flexible electronics. This work presents a porous composite of PZT@carboxymethyl chitosan (CMCS) in thermoplastic polyurethane (TPU). The core-shell structure enhances interfacial compatibility, while the porous TPU skeleton facilitates stress transfer and amplification, allowing high piezoelectric content. The resulting PZT@CMCS/TPU devices achieve an output voltage of 53 V and current of 13 μA, an 11-fold improvement over conventional PZT composite films. This approach enables flexible piezoelectric devices with high performance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3617-x
Macrophages are pivotal in infection resolution and tissue repair via dynamic M1-to-M2 phenotypic polarization. Although various nano-biomaterials can modulate macrophage polarization, achieving sequential M1-to-M2 transition using a single nanoformulation remains challenging. Here, we propose a strategy employing transition metal carbide/nitride (MXene) nanosheets, internalized by macrophages, as the sole regulator to induce sequential polarization. Under a rotating magnetic field, the high electrical conductivity and magnetoelectric activity of endocytosed MXene generate electrical signals and reactive oxygen species (ROS), driving M1 polarization. Upon magnetic field removal, the inherent bioactivity of MXene facilitates repolarization to the M2 phenotype. Mechanistically, this transition involves inhibition of the NF-κB signaling pathway and activation of the JAK-STAT signaling pathway. In vivo, MXene nanosheets under on-off rotating magnetic field stimulation enabled sequential M1-to-M2 polarization, promoting bacterial clearance and tissue regeneration in infected wounds. This two-step sequential strategy targeting macrophages offers a promising therapeutic approach for infected wound healing.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202506021
To elucidate the seasonal variation in cadmium (Cd) accumulation in ratoon rice and its relationship with root surface iron plaque, this study compared Cd concentrations in brown rice and the characteristics of iron plaque components (amorphous Fe, Am-Fe; crystalline Fe, Cry-Fe) between the main and ratoon crops of six rice varieties under different stubble heights. A field experiment was conducted in a Cd-contaminated paddy in Liuyang, Hunan (soil total Cd: 0.56 ± 0.06 mg·kg⁻¹). Ratoon crop treatments included low stubble (20 cm) and high stubble (60 cm). Brown rice Cd concentrations varied by variety, season, and stubble height. Low stubble generally increased brown rice Cd in the ratoon crop compared to high stubble; high stubble reduced Cd in most varieties relative to the main crop. Health risk assessment indicated that low stubble in the ratoon crop posed higher non-carcinogenic risk than the main crop and high stubble, while carcinogenic risks exceeded acceptable levels across all treatments. Iron plaque Am-Fe and Cry-Fe concentrations in the ratoon crop were generally lower than in the main crop, with Am-Fe consistently exceeding Cry-Fe. In the main crop, total Fe, Am-Fe, and Cry-Fe on root surfaces were significantly negatively correlated with brown rice Cd (P < 0.05), but correlations were not significant in the ratoon crop. High stubble reduced Cd accumulation and non-carcinogenic risk in most varieties, yet carcinogenic risk remained. Iron plaque significantly impeded Cd uptake in the main crop but its effect weakened in the ratoon crop. Selecting low-Cd-accumulating varieties and optimizing stubble height are key strategies for safe ratoon rice production in Cd-contaminated areas.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604011
Reverse osmosis (RO) membrane fouling remains a critical bottleneck in reclaimed water production, yet its spatial heterogeneity over extended operation is poorly understood. This study investigated fouling characteristics and microbial community dynamics on RO membranes after 3.5 years of operation in a full-scale microfiltration-reverse osmosis (MF-RO) system treating reclaimed water. Long-term monitoring showed stable effluent quality (turbidity <0.1 NTU, conductivity <400 μS/cm), but RO inlet pressure exhibited seasonal fluctuations of 15%–22% between summer and winter, attributed to water viscosity changes. Membrane autopsies revealed distinct fouling layers at the inlet (RO1) and outlet (RO2) ends. RO1 featured a dense bio-inorganic composite fouling layer with CaSO4 crystals and rod-shaped microbial aggregates (5–10 μm), dominated by Proteobacteria (77.11%), particularly Alphaproteobacteria (71.49%) and Xanthobacteraceae (35.29%), which secreted extracellular polymeric substances (EPS) to form biofilms. In contrast, RO2, exposed to higher salinity, showed reduced microbial abundance (Proteobacteria decreased to 64.79%) and a shift toward halotolerant taxa, including Microbacteriaceae (23.73%) and Actinobacteriota (24.76%), with EPS secretion increased by 42%. Alphaproteobacteria relative abundance dropped by 19.3%, while Gammaproteobacteria rose to 12.54%. These findings elucidate salinity-driven microbial succession and spatial heterogeneity of fouling, providing a basis for targeted antifouling strategies and 'zonal-graded' cleaning protocols in reclaimed water plants.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3778-8
The global surge in polyvinyl chloride (PVC) waste demands urgent technological solutions that address both environmental persistence and resource recovery. Here, we present a triple-functionalization strategy that converts chlorinated plastic waste into high-performance sodium-ion battery anodes through molecular-level control of carbon architectures. Sequential dichlorination, sulfonation, and N-doping collaboratively reconfigure precursor reactivity, steering pyrolysis toward hierarchically porous hard carbon with tailored defect chemistry. Sulfonic groups stabilize 3D carbon skeletons during carbonization, enabling closed-pore formation with an average diameter of ~2.55 nm while N-doping expands interlayer spacing (0.382 nm) and creates adsorption-active pyrrolic-N sites. This defect-engineered synergy delivers unprecedented sodium storage metrics: 355 mAh g−1 reversible capacity at 0.1 A g−1 (95.4% of graphite’s Li-ion capacity), a capacity retention of 216 mAh g−1 after 1000 cycles at 1.0 A g−1 (70.1% capacity retention), and 188 mAh g−1 even at a high current density of 5.0 A g−1. Operando analyses reveal a potential-dependent storage hierarchy: surface-dominated adsorption transitions to intercalation/filling-dominated behavior with defect-buffered structural integrity. The process simultaneously achieves 25% carbon yield from PVC and avoids toxic dioxin emissions, establishing a scalable prototype for sustainable energy storage systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3742-5
Nematic liquid crystal elastomers (NLCEs) exhibit excellent mechanical properties and diverse deformation modes, while cholesteric liquid crystal elastomers (CLCEs) as photonic crystals (PCs) possess superior optical performance and intelligent response characteristics. Combining these two elastomers into a monolithic material is a challenging yet promising endeavor. Here, we designed and synthesized a new diselenide-bonded molecule (DSeAc), whose lower bond energy between selenium atoms endows it with excellent bond exchange ability. Consequently, two LCE matrices containing DSeAc molecules can achieve seamless bonding under mild conditions via dynamic diselenide bond exchange. By integrating a CLCE film and an NLCE actuator into a monolithic film, we enable the integration of two functional components, whose functional characteristics can be tailored as required. This function block combination strategy offers a promising pathway for developing smart materials with complex functions, showing great potential in information storage, anti-counterfeiting, and biomimetics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3963-5
Metal additive manufacturing (MAM) enables integrated one-piece fabrication of parts, high material utilization efficiency, and unparalleled design freedom. However, problems such as low production efficiency, difficulties in ensuring quality stability and defect control limit the large-scale industrial application of AM. In-situ active modulation for AM enables dynamic regulation of parts during the fabrication process, thereby enhancing the quality of the final fabricated parts without introducing extra processing steps. In-situ active regulation enables direct intervention during defect nucleation, providing better effectiveness than post-printing repairs while avoiding performance degradation risks associated with post-processing. Based on the difference of core factors directly affected during regulation, in-situ active regulation is categorized into the following. (1) Process and path parameter optimization, where regulation directly impacts manufacturing-related procedural rules. It is the simplest method of control and the preferred approach, with widespread attention focused on its effects on microstructure and mechanical properties. (2) Laser beam shaping, where regulation directly influences the energy carrier morphology. To address issues such as edge over-melting and localized energy deficiency caused by non-uniform energy distribution, laser beam shaping should be employed. (3) Additional physical field modulation achieved by superimposing supplementary physical fields. When optimal process and path parameters still fail to obtain the desired microstructure and mechanical properties, additional physical field control may be considered. Meanwhile, this work summarized the effects of different additional physical fields on the mechanical properties of various metallic base materials. The future trends of in-situ modulation in additive manufacturing are also discussed.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025102801
This study develops a multivariate time-series forecasting model for water quality in the Lhasa River, focusing on four key indicators: water temperature, pH, dissolved oxygen, and turbidity. Data preprocessing integrated multiple missing-value imputation strategies and interquartile range (IQR) outlier removal. Boxplots and relative standard deviation (RSD) assessed data distribution and dispersion, while autocorrelation and Pearson correlation analyses revealed periodic patterns and inter-variable relationships. Four representative algorithms—Support Vector Regression (SVR), Extreme Gradient Boosting (XGBoost), CNN-BiLSTM-Attention, and TCN-Transformer—were optimized via Bayesian hyperparameter tuning. Model performance was evaluated using MAE, MSE, RMSE, and R². The study systematically compared the effects of different missing-value handling methods, both independently and combined with IQR outlier removal. Results indicate that CNN-BiLSTM-Attention excels in water temperature prediction, suitable for relatively stable and simple patterns. In contrast, TCN-Transformer demonstrates superior performance for pH, dissolved oxygen, and turbidity, which exhibit strong nonlinearity and long-term dependencies, effectively capturing temporal dependencies and coupling relationships. The findings provide a viable technical route and theoretical reference for river water quality monitoring and intelligent early-warning systems.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025032001
This study investigates the variation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and their monomer components during low-temperature thermal decomposition (250–500 °C) of municipal solid waste incineration fly ash from a typical mechanical grate furnace. Results demonstrate that pyrolysis temperature and time significantly affect the solid-phase removal rates of PCDD/F mass concentration and toxic equivalent (TEQ) concentration. The influence weights of temperature on mass and TEQ removal rates are 20.86 and 21.41, respectively, while those of time are 4.27 and 3.36. Response surface analysis identifies optimal conditions at 380 °C for 1.0 h. At 250–300 °C, both PCDFs and PCDDs concentrations increase synchronously, indicating enhanced formation. At 300 °C for 2.0 h, high-chlorinated congeners undergo dechlorination to low-chlorinated ones, notably increasing 2,3,7,8-T4CDD (I-TEF=1.0) and 1,2,3,7,8-P5CDD (I-TEF=0.5). From 350 °C upward, significant degradation occurs; at 380 °C (1.0 h), degradation rates for PCDDs and PCDFs reach 97.8% and 97.6%, respectively, effectively reducing TEQ-contributing congeners. The process proceeds in two stages: initial dechlorination, followed by destruction of dioxin-like compounds at higher temperatures. 2,3,7,8-T4CDD emerges as a critical component for detoxification. These findings provide a scientific basis for optimizing thermal treatment of fly ash to minimize environmental and health risks.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025040104
The oxidative transformation of 2,6-dichlorophenol (2,6-DCP) was investigated in three typical zonal soils: black soil, red soil, and brown soil. Results demonstrated that 2,6-DCP underwent oxidative coupling in all soils, yielding hydroxylated polychlorinated diphenyl ethers (OH-PCDEs) and hydroxylated polychlorinated biphenyls (OH-PCBs) as primary products. The highest oxidative efficiency occurred in black soil, with approximately 85.1% of 2,6-DCP transformed within three days. In contrast, red and brown soils exhibited lower efficiencies, indicating a strong dependence on soil properties. Thermodynamic analysis revealed that the oxidative coupling reaction is endothermic, with elevated temperatures favoring reaction progress. Furthermore, soil microorganisms and dissolved oxygen were identified as critical controlling factors, acting synergistically to drive the reaction. This study provides the first evidence of natural oxidative coupling of 2,6-DCP in soil, forming OH-PCDEs and OH-PCBs. These findings offer significant scientific insight into the environmental fate of halogenated phenolic pollutants in terrestrial systems.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025032704
Chlorogenic acid (CGA), a key component of the anti-COVID drug Lianhua Qingwen, is recalcitrant to biodegradation and tends to bioaccumulate, posing risks to aquatic ecosystems. Conventional water treatment methods are inadequate for its removal. This study investigated the degradation of CGA using a magnetic field coupled Fe-C activated persulfate (MF/Fe-C/PS) advanced oxidation process. The degradation efficiencies of Fe-C, PS, Fe-C/PS, and MF/Fe-C/PS systems were compared, and the dominant reactive species and their contributions were identified. The effects of initial pH, persulfate (PS) concentration, Fe-C dosage, and inorganic anions on degradation kinetics were examined, along with the degradation pathway and disinfection byproduct (DBP) formation potential. Results showed that MF/Fe-C/PS achieved 99% degradation of CGA within 60 min under optimal conditions: pH=3, PS concentration 1.5 mmol·L−1, and Fe-C dosage 0.4 g·L−1. Coexisting Cl−, Br−, and I− inhibited CGA oxidation to varying degrees, as did natural organic matter (FA and BAS). The reactive species SO4−·, ·OH, and 1O2 contributed 41.6%, 30.5%, and 27.9%, respectively. Degradation mechanisms included hydrolysis, dehydroxylation, decarboxylation, and benzene ring cleavage. Pre-oxidation by MF/Fe-C/PS significantly reduced the DBP formation potential during subsequent chlorination/chloramination. Energy per order (EE/O) analysis indicated favorable economic efficiency.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042103
This study investigated the spatiotemporal distribution, ecological risk, and sources of seven heavy metals (Cr, Cd, Cu, Ni, Pb, Zn, As) in surface sediments of Ranwu Lake, Xizang. Twelve samples were collected during the glacial ablation period (July 2024) and late glacial ablation period (November 2024). Concentrations were determined and analyzed using inverse distance weighting (IDW) for spatial patterns, geo-accumulation index (Igeo) and potential ecological risk index (RI) for risk assessment, and correlation analysis (CA), principal component analysis (PCA), and absolute principal component score-multiple linear regression (APCS-MLR) for source apportionment. Results showed that during glacial ablation, mean Cr, Cd, Pb, and As exceeded Xizang soil background values, while in the late ablation period only Cd, Pb, and As remained elevated. Spatial distribution varied between periods, with high concentrations in the middle and lower lake during ablation, shifting to the lower lake in the late period. Igeo and RI indicated overall low ecological risk, with Cd as the primary risk factor; mean RI values were 81.79 and 98.30 for the two periods, respectively. Source apportionment revealed that heavy metals mainly originated from natural and transportation sources, with traffic emissions being the major contributor to ecological risk. Specifically, Cr, Ni, and As were predominantly natural, Cd and Pb were mainly traffic-related, and Cu and Zn were influenced by both natural and traffic sources.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042802
Activated carbon, characterized by its extensive pore structure, high specific surface area, and superior adsorption capacity, is widely employed in advanced water treatment. However, upon reaching adsorption saturation, its efficacy diminishes, necessitating replacement or regeneration. Thermal regeneration stands out due to its high desorption efficiency, simple equipment requirements, and low energy consumption, making it the predominant industrial method. Despite its prevalence, systematic investigations into the underlying reaction mechanisms and the influence of operational parameters remain insufficient. This review comprehensively examines common thermal regeneration technologies for saturated activated carbon, including multi-hearth furnaces, rotary kilns, superheated steam, microwave, and solar regeneration. It delineates the fundamental principles, process flows, advantages, disadvantages, and current research status of each method. The desorption and reaction mechanisms of pollutants within activated carbon pores during thermal regeneration are discussed in detail, along with the effects of critical conditions such as temperature, atmosphere, and purge gas flow rate on pollutant removal efficiency. Furthermore, the relationship between activated carbon performance parameters and regeneration efficiency is analyzed, and innovations based on conventional thermal regeneration, as well as integration with emerging technologies, are explored. Finally, the challenges facing thermal regeneration are summarized, and future research priorities are proposed, focusing on the treatment of waste gas and liquid byproducts, technology integration, and enhancement of overall regeneration performance. This review aims to provide a scientific foundation for the sustainable recycling of activated carbon in industrial applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3951-4
Silicon anodes offer an ultrahigh theoretical capacity (4200 mAh g−1) but suffer from >300% volumetric expansion during cycling and unstable solid electrolyte interphase (SEI) formation, leading to rapid capacity fading. Here, we design a hierarchical composite p-cSi@aSi@MgSiN2@C featuring a porous crystalline-amorphous silicon core (p-cSi@aSi), an in-situ MgSiN2 transition layer, and an outer nitrogen-doped carbon shell. The 3D interconnected pores accommodate volume expansion, while amorphous silicon enables isotropic lithiation-induced strain, eliminating crystalline phase transition barriers. The MgSiN2 layer transforms into a tough Li3N-rich SEI with ultra-fast ion channels, and the carbon shell provides mechanical confinement and electronic conductivity. This synergistic interface engineering achieves an initial coulombic efficiency (ICE) of 81.4%, a charge transfer resistance of 16.4 Ω after 200 cycles (64% reduction), and a Li+ diffusion coefficient of 1.72×10−11 cm2 s−1. The anode delivers 1719.3 mAh g−1 at 0.2 C after 200 cycles and 823.8 mAh g−1 at 0.5 C after 500 cycles. The molten salt electrolysis synthesis achieves a current efficiency of 68.12% and specific energy consumption of 12.76 kWh kg−1, with an estimated electricity cost of 1154.69 USD ton−1, only 20% of commercial Si/C anodes. This work resolves the ICE-cycle life trade-off and provides a scalable, cost-effective approach for next-generation high-energy batteries.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60708-6
Mercury emissions from coal combustion are highly toxic, volatile, and bioaccumulative, posing long-term threats to ecosystems and human health. This review systematically examines the current status and control policies of mercury emissions from coal combustion in China, analyzing distribution characteristics and transformation mechanisms during combustion, with emphasis on collaborative removal in pollution control devices after ultra-low emission retrofitting. A progressive strategy of 'synergistic enhancement–deep purification–resource recycling' is proposed, comprising three tiers: optimizing operational parameters of existing control systems to enhance synergistic mercury removal; developing efficient adsorption and catalytic oxidation technologies for industrial application; and advancing integrated mercury removal and recovery technologies, such as magnetosphere-based sorbents and recovery processes, focusing on high-value utilization. The paper also outlines future research directions aligned with international compliance and domestic environmental tax policies, providing theoretical and technical support for China's commitments to near-zero emissions of coal combustion pollutants.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4274-x
The escalating power density of electronic devices necessitates effective visible-light shielding in advanced packaging to ensure circuit security and long-term reliability. Photosensitive polyimides (PSPI) serve dual roles as photodefinable dielectrics and structural layers, but intrinsically black PSPI (B-PSPI) suffer from competitive ultraviolet (UV) absorption between chromophores and photosensitive moieties, limiting co-optimization of deep visible-light blocking and lithographic resolution. Here, we report a main-/side-chain spatial decoupling strategy to synthesize a novel B-PSPI. By polymerizing pyromellitic dianhydride with a main-chain coloring monomer (4,4'-diaminodiphenylamine) and a side-chain photosensitive monomer (1,4-dihydropyridine-functionalized diamine), the monomer stoichiometric ratio is precisely engineered. This design spatially isolates functional groups and enhances charge transfer, yielding exceptional visible-light shielding (CIE L* index of 21.39, cut-off wavelength ≈ 555 nm) with good lithographic sensitivity. UV exposure triggers in situ generation of coordination sites from photosensitive groups, anchoring active metal species for electroless copper plating. This enables direct additive fabrication of fine copper lines (40/80 μm line width/spacing) with robust Cu/B-PSPI interfacial adhesion of 16.6 MPa. This work provides a robust molecular design paradigm for B-PSPI, integrating superior optical shielding and surface metallization for high-density interconnect applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4098-8
Fluorescence image-guided photodynamic therapy (PDT) enables real-time monitoring of photosensitizer biodistribution and metabolism for optimized treatment timing. However, its application remains limited by reliance on high-end imaging systems. To address this, we designed three novel small-molecule photosensitizers (TTNb, TTAn, TTPh) based on a 2-vinylbenzoic acid scaffold, functionalized at the 5-position with nitro, amino, or hydrogen groups. Replacing the nitro group with amino or hydrogen switched aggregation behavior from aggregation-induced emission (AIE) to aggregation-caused quenching (ACQ), accompanied by a red-to-green fluorescence shift and subcellular relocation from liposomes to lysosomes. These findings establish design principles for ratiometric nitroreductase probes and enable systematic comparison between AIE and ACQ photosensitizers. Among these, TTAn exhibited superior cellular uptake (2800 times higher than Ce6 in Eca-109 cells), specific lysosomal targeting, balanced reactive oxygen species (singlet oxygen/superoxide anion) generation, and intense fluorescence. Under white light irradiation, TTAn achieved an IC50 of 21 nM, surpassing Ce6 by 50-fold. Notably, TTAn produced strong fluorescence in mice tumors under both one- and two-photon excitation, detectable using conventional imaging tools (smartphones, DSLR cameras) or even visible to the naked eye, confirming outstanding tumor specificity. Leveraging these advantages, TTAn enabled successful image-guided two-photon PDT in Eca-109 tumor-bearing mice with a single treatment, demonstrating potent therapeutic efficacy and biosafety. This work provides a strategic blueprint for developing small-molecule theranostic agents that operate without complex fluorescence imaging systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4222-9
The proliferation of high-frequency communication technologies has escalated electromagnetic (EM) pollution, posing risks to health and device reliability. Conventional microwave absorbers dissipate EM energy as heat, creating thermal management burdens and energy waste. This study introduces Bi2Se3 nanosheets, a topological insulator with surface conductivity and internal insulation, as a dual-functional material capable of both microwave absorption and thermoelectric conversion. Nanosheets with controlled morphology were synthesized via a polyol reduction method, with thickness and lateral size tuned by preparation conditions. The resulting composites exhibited excellent microwave absorption, achieving a broad absorption bandwidth of 2.95 GHz at sub-millimeter thickness. A multilayered structure design enabled full-band absorption from 2 to 18 GHz using a single absorbent. The Seebeck coefficient, derived from temperature differences up to 110 °C, was -152 μV/K, indicating efficient conversion of absorbed EM energy into electrical energy. This work demonstrates the potential of Bi2Se3 nanomaterials for self-powered electromagnetic devices, addressing both EM pollution and energy supply challenges.