SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4467-x
Conventional eye-movement interaction systems depend on video capture, infrared tracking, and image recognition, which impose inherent constraints on accuracy, response latency, and stability. This study introduces an eyelash-guided signal interaction system based on a triboelectric nanogenerator (PF-TENG) using PDMS-FDTS thin films. The system employs eyelash movements as interactive inputs, eliminating the need for complex optical acquisition devices. A CNN-LSTM hybrid neural network classifies distinct eyelash movement patterns with a classification accuracy exceeding 98.5%. The PF-TENG device exhibits ultra-flexibility and transparency, enabling seamless integration onto eyeglasses without obstructing the user's field of view. Experimental validation demonstrates real-time monitoring of ocular states for driving fatigue detection, accurately identifying fatigue signs and enhancing application potential in intelligent driving. The system offers a natural, comfortable input modality and significant advantages for human-machine interaction, with broad prospects in eye-movement control and intelligent transportation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4371-6
The sluggish kinetics of the oxygen reduction reaction (ORR) necessitates platinum-based catalysts, but their high cost and scarcity drive the search for platinum-group metal-free (PGM-free) alternatives. Fe−N−C catalysts with atomically dispersed Fe−N4 sites are promising, yet their practical performance is limited by buried active sites and poor mass transport. Here, a crumpled, multi-scale porous Fe−N−C catalyst (Fe−N−PCG) is synthesized via spray pyrolysis coupled with high-temperature metal etching. The crumpled morphology, formed by capillary compression during rapid solvent evaporation, and in-plane mesopores from Fe nanoparticle etching, synergistically enhance site accessibility and mass transport. Fe−N−PCG achieves a site density (SD) of 2.74×10^19 sites g−1 and Fe utilization (UFe) of 51.7%. As a gas diffusion electrode, it delivers a mass transport overpotential (ηmt) of 67 mV at 800 mA cm−2. In zinc-air batteries, Fe−N−PCG exhibits a peak power density of 296.1 mW cm−2 at 500 mA cm−2, outperforming Pt/C (241 mW cm−2 at 438 mA cm−2). At 50 mA cm−2, it delivers a discharge voltage of 1.19 V and a specific capacity of 815 mAh g−1, surpassing Pt/C (1.13 V, 715 mAh g−1). These results demonstrate that morphology and porosity engineering can concurrently optimize intrinsic activity, site utilization, and mass transport, offering a rational design strategy for high-performance PGM-free catalysts.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4202-3
Carbon dots (CDs) with absorption in the second near-infrared window (NIR-II, 900-1700 nm) hold promise for tumor theranostics, yet existing synthesis methods often involve complex procedures, harsh conditions, or lack precise control. Here we report a 'self-photooxidation-restructuring' strategy that enables structural reorganization of the carbon core in CDs, achieving a significant redshift of absorption into the NIR-II region. Under ultraviolet (UV) light irradiation, the precursor (B-CDs, absorption in UV region) generates singlet oxygen, which self-oxidizes aldehyde groups and the carbon skeleton of B-CDs to stronger electron-withdrawing carboxyl groups and carbon radicals, respectively. These processes facilitate the formation of new C=C bonds between isolated aromatic domains, thereby transforming B-CDs into novel CDs (N-CDs) characterized by enhanced donor-acceptor interactions and a redshift in absorption toward the NIR-II window. Various experimental data, including high-resolution XPS, FTIR, NMR, EPR, have proved the proposed formation mechanism. The novel N-CDs afforded a high photothermal conversion efficiency of up to 71.33%, which enabled 1064 nm laser-activated photoacoustic imaging (PAI)-guided photothermal therapy (PTT) in tumors. This work opens a new avenue for the synthesis and modulation of CDs in the NIR-II region.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4176-y
Three-photon microscopy (3PM) in the near-infrared-III (NIR-III) window (1600–1840 nm) enables high-resolution visualization of cerebral vasculature in vivo, but its imaging depth and quality are limited by the performance of fluorescent probes. Here, we report a probe optimization strategy transitioning from mirror symmetry to centrosymmetry, yielding a highly symmetric aggregation-induced emission (AIE) molecule, T4PQ. The centrosymmetric structure aligns donor-acceptor units, promoting uniform electron cloud delocalization and directional charge transfer, which enhances exciton formation and suppresses non-radiative decay, thereby increasing fluorescence quantum yield. This symmetry also boosts the three-photon absorption cross-section by enhancing electron delocalization and transition dipole moment, enabling stronger nonlinear optical responses under long-wavelength excitation. T4PQ nanoparticles (T4PQ NPs) exhibit an enhanced three-photon absorption cross-section, high fluorescence quantum yield, and excellent photostability. In murine models, T4PQ NPs achieved three-dimensional cerebrovascular imaging at a depth of 1785 μm and real-time hemodynamic observation in microvessels at 1006 μm depth, with good biocompatibility. These results validate the advantage of centrosymmetric molecular design for deep-brain imaging probes, offering a high-performance tool for neurovascular research.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3671-0
Photothermal therapy (PTT) is a non-invasive tumor treatment that offers controllability, non-drug resistance, and precise ablation, yet its efficacy is limited by uncontrolled heat diffusion and weak immune responses, often leading to metastasis. Here, we report a chondroitin sulfate-modified Prussian blue-montmorillonite immunoregulator (PM@CS) that integrates tumor cell adhesion and Golgi targeting to confine photothermal damage at the organelle level. PM@CS accumulates on the Golgi apparatus, reducing heat transfer distance and enhancing photothermal ablation. This targeted hyperthermia disrupts post-translational modification and secretion of metastasis-associated proteins, with GOLPH3 and GOLM1 expression reduced by 63.4% and 70.3%, respectively. Furthermore, PM@CS promotes dendritic cell maturation (3.3-fold increase in CD80+ and CD86+ populations) and enhances antigen-specific CD4+ and CD8+ T cell proliferation, attributed to the immunoadjuvant properties of montmorillonite. Notably, PM@CS upregulates voltage-gated calcium channels (CaV) and enhances Ca2+ influx, activating calcium signaling cascades that amplify immunotherapy. This synergistic approach inhibits primary tumor growth and lung metastasis, offering a promising strategy for cancer treatment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3669-1
Halide perovskite light-emitting diodes (PeLEDs) have advanced rapidly due to their high photoluminescence quantum yield, tunable bandgap, and color purity. However, conventional perovskites exhibit small exciton binding energies, which weaken radiative recombination and limit external quantum efficiency (EQE). Strong spatial confinement strategies, such as thin films, small grains, or quantum-confined structures, have boosted EQE beyond 20% but introduce Auger recombination and ion migration, causing efficiency roll-off and instability. This commentary highlights a novel approach by Xiao et al. (Nature, 2025) that employs weakly space-confined all-inorganic CsPbBr3 perovskites, synthesized using sacrificial additives hypophosphorous acid (HPA) and ammonium chloride (NH4Cl). This method yields highly oriented monocrystalline domains exceeding hundreds of nanometers with no observable grain boundaries, contrasting with control films (submicrometre grains with abundant boundaries) and strongly confined systems (~20 nm crystallites with organic ligands). The reduced grain boundaries lower defect density and block ion migration, while controlled crystallization suppresses vacancies and lattice distortions, enhancing carrier mobility and raising the ion migration energy barrier. The strategy achieves record-breaking performance and stability, addressing EQE roll-off and operational lifetime limitations. This approach offers a versatile framework for other all-inorganic perovskite systems, advancing PeLEDs toward practical high-brightness displays and lighting.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3762-9
The integration of interfacial photothermal conversion and hydrovoltaic effects into bifunctional evaporators offers a promising route to simultaneously address freshwater scarcity and energy demands. However, the development of low-cost bifunctional evaporators and elucidation of the underlying co-generation mechanism remain challenging. Here, we report a porous carbon derived from waste polyester via a metal-organic framework (MOF)-assisted carbonization strategy, which is subsequently fabricated into a bifunctional evaporator for freshwater and hydroelectricity co-generation. The porous carbon exhibits a high specific surface area of 904 m² g⁻¹, hierarchical micro- and mesopores, and abundant oxygen-containing groups. The resulting evaporator demonstrates broadband light absorption, localized thermal management, good hydrophilicity, and high flexibility. Under 1 sun illumination, it achieves an open-circuit voltage of 250 mV, a short-circuit current of 14 μA, and an evaporation rate of 2.34 kg m⁻² h⁻¹, ranking among the most efficient freshwater-hydroelectricity co-generators. The weakened hydrogen-bonding network reduces the water evaporation enthalpy to 1.7 kJ g⁻¹. Mechanistic studies, including molecular dynamics simulations, reveal that selective Na⁺ interaction induces differential ion migration rates, generating a streaming potential. Additionally, the photothermal effect enhances voltage output by promoting interfacial ion concentration gradients. Outdoor tests confirm stable voltage output of 250 mV and freshwater production of 2.34 kg m⁻². This work provides a scalable platform for fabricating advanced evaporators from waste plastics and unravels the co-generation mechanism, offering a sustainable strategy to mitigate freshwater and energy crises.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507029
This study systematically evaluates the environmental risks associated with the resource utilization of municipal solid waste incineration (MSWI) fly ash in the production of aerated concrete, co-prepared with multiple solid wastes. The focus is on the leaching behavior and total content of heavy metals (Cr, Pb, Cd, Cu, Zn) under CO2 curing and chelating agent stabilization. Water washing pretreatment parameters (liquid-to-solid ratio, washing time, ash-to-slag ratio) were optimized for chloride removal. Results demonstrate that CO2 curing suppresses the leaching of most metals; leaching concentrations of Cr, Pb, Cd, and Zn decrease with reduced fly ash content, whereas Cu leaching increases when fly ash is absent. The addition of 17.5% organic sulfur stabilizer (DTC) significantly outperforms inorganic sulfide (Na2S) in immobilizing heavy metals, achieving compliance with national standards without compromising compressive strength or carbon sequestration. Water washing effectively reduces soluble chloride content to below 1% (mass fraction), meeting the HJ 1134-2020 regulatory limit. Optimal parameters include a liquid-to-solid ratio of 5, washing time of 20 min, and a raw material ratio of incineration bottom slag:fly ash:slag = 40:20:40. Under these conditions, the final product exhibits a compressive strength of 1.50 MPa, with heavy metals and soluble chlorides fully compliant. This work provides key technical support for the safe recycling of MSWI fly ash in building materials.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3407-0
Grain boundary (GB) engineering has emerged as a promising strategy to enhance the near-room-temperature performance of Mg3(Sb,Bi)2-based thermoelectric materials, yet effective control of Mg distribution at GBs remains a significant challenge. Here, we report a novel approach to achieve targeted Mg segregation at GBs through strategic Ag incorporation in Mg3.3Sb0.5Bi1.497Te0.003. Through comprehensive microstructural characterization and first-principles calculations, we demonstrate that Ag preferentially segregates at GBs, forming Mg-rich MgAg alloy phases while maintaining limited solid solubility within the matrix. This unique GB architecture simultaneously optimizes multiple thermoelectric parameters: the Mg-rich GB regions significantly provide efficient carrier transport channels and enhance carrier mobility, while the MgAg phases and lattice disorders effectively scatter phonons without disrupting electron transport. Consequently, the optimized composition (x = 0.01) exhibits a remarkable enhancement in power factor at 300 K and maintains an average ZT of ~1.0 across 300–400 K. The material also demonstrates excellent mechanical properties and thermal stability, making it particularly suitable for near-room-temperature applications. Our findings not only establish an effective strategy for GB engineering in Mg3(Sb,Bi)2 systems but also provide valuable insights into the rational design of high-performance thermoelectric materials through interface modification.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61108-0
Adipic acid is a key monomer for nylon-6,6 and nylon-6, yet its industrial production via nitric acid oxidation of KA oil suffers from high energy consumption and N2O emissions. This study reports a green catalytic system for one-pot oxidation of cyclohexane to adipic acid using a Cu/Cu2O@C composite catalyst derived from wood chips. During pyrolysis, wood chips serve as both carbon support precursor and in-situ reducing agent, converting Cu2+ into Cu/Cu2O active species. The abundant defects in biomass carbon form strong coordination interactions with copper, regulating the electronic distribution of active sites and enhancing catalytic performance. Under optimized conditions (100 °C, 12 h), the Cu/[email protected] catalyst achieves a cyclohexane conversion of 19.36% and an adipic acid selectivity of 73.28%. Mechanistic studies reveal that the electronic interaction between the carbon support and copper species strengthens adsorption of cyclohexanone, promoting selective formation of adipic acid. The reaction follows a free radical chain mechanism involving hydroxyl and alkyl radicals. This work provides a viable strategy for developing eco-friendly, low-cost, and high-efficiency catalytic materials for industrial adipic acid synthesis.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202509049
This study systematically compared three virus enrichment and concentration methods—polyethylene glycol (PEG) precipitation, aluminum salt coagulation, and centrifugal ultrafiltration—for detecting SARS-CoV-2 in high-turbidity, high-strength wastewater from inbound flights. The aluminum salt coagulation method exhibited the best overall performance, achieving an average recovery rate of 25.95% for SARS-CoV-2 pseudovirus, significantly higher than PEG precipitation (12.91%) and centrifugal ultrafiltration (0.22%) (P<0.05). Its detection limit reached 10 copies·mL⁻¹, whereas centrifugal ultrafiltration suffered severe membrane fouling, limiting detection to 1,000 copies·mL⁻¹. Considering the high pH buffering of flight wastewater, the aluminum salt method was optimized by adjusting pH to 6.00±0.4, employing rapid magnetic stirring, and reducing mixing time to 1 minute, yielding an average recovery of 27.56% (not significantly different from the original 25.95%, P>0.05). An automated enrichment device was developed based on the optimized method, reducing processing time per sample from 115 min to 60 min while maintaining comparable recovery and improved repeatability. Applied to 1,309 wastewater samples from inbound flights between January 2024 and May 2025, the average detection rate of SARS-CoV-2 was 45.45%, with trends consistent with national COVID-19 epidemiological data. The automated device demonstrates suitability for routine surveillance, providing technical support for port epidemic prevention.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025100102
Per- and polyfluoroalkyl substances (PFAS) are emerging contaminants of concern in China, and drinking water is a major exposure pathway. This study investigated 17 PFAS in surface water from 12 drinking water sources along the Hubei section of the Yangtze River mainstream during dry, normal, and wet seasons. Total PFAS concentrations ranged from 10.84 to 41.05 ng/L (dry), nd to 62.60 ng/L (normal), and 6.77 to 29.00 ng/L (wet). Predominant compounds were PFBS, PFOA, PFHxA, PFBA, and PFOS. Lake-type sources exhibited significantly higher concentrations than river-type sources, and dry and normal seasons showed higher levels than wet season. Compared to other Chinese sources, PFAS levels in Hubei were moderate, with fluorochemical plant inputs and population density as likely influencing factors. Ecological and health risk assessments indicated acceptable risks. In four selected water supply systems, PFAS distribution from source to tap was examined; PFOA, PFBA, PFHxA, and PFBS were dominant, and secondary water supply did not significantly introduce or remove PFAS. Health risks from tap water were within acceptable limits.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606022
This study presents a numerical simulation of the internal flow field in a volatile organic compounds (VOCs) catalytic combustion reactor used in an enameled wire enterprise. Using ANSYS Fluent, the effects of inlet expansion section length, inlet expansion section angle, and catalyst bed spacing on the velocity field were systematically investigated. Additionally, the influence of heating tube configuration on the temperature field was analyzed. The results indicate that an expansion section length of 250 mm is optimal, balancing spatial constraints and the avoidance of recirculation zones. A zero-degree expansion angle yields the most uniform velocity distribution, though practical considerations necessitate case-specific angle selection. A catalyst bed spacing of 0.05 m satisfies the engineering requirement of maintaining pressure drop across a single catalyst layer below 200 Pa while significantly improving gas distribution within the bed. Alternating heating tubes on both sides of the reactor enhance temperature uniformity and elevate the overall catalyst bed temperature, thereby promoting efficient VOCs catalytic combustion. These findings provide quantitative guidance for reactor design optimization, contributing to improved catalytic performance and extended catalyst lifespan.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3864-4
Organic room temperature phosphorescence (RTP) materials, particularly those emitting in the near-infrared (NIR) region, hold great promise for bioimaging due to their deep-tissue penetration and minimal autofluorescence interference. However, achieving efficient NIR RTP with long lifetimes remains challenging due to inefficient triplet exciton utilization. Herein, we propose a dark triplet state activation strategy to achieve efficient NIR RTP by leveraging host–guest energy transfer. Using benzophenone derivatives (BP, OBP, MBP, PBP) as rigid host matrices with high intersystem crossing (ISC) efficiency and an NIR fluorophore (MPTCF) as the guest, we achieve efficient Dexter-type triplet-triplet energy transfer (TTET) that converts non-emissive host triplets into guest-centered NIR phosphorescence. Systematic optimization of the host–guest system has shown that PBP/MPTCF exhibits exceptional performance, including long phosphorescence centered at 705 nm, an ultralong phosphorescence lifetime (210.3 ms), and high ISC efficiency (44.4%). When fabricated into nanoparticles (NPs), PBP/MPTCF exhibits superior performance, featuring prolonged phosphorescence signals (>120 s), deep tissue penetration capability (>2 mm), and excellent biocompatibility (cell viability >95% at 300 μM). In addition, this system enables high-contrast subcutaneous imaging with excellent dispersibility and stable in vivo imaging capability. More importantly, PBP/MPTCF NPs demonstrate precise lymph node mapping through time-gated phosphorescence imaging and efficient tumor visualization within 4 h post-injection with a high tumor-to-liver ratio of 2.8. The successful activation of dark triplet states through this host–guest approach provides a general design principle for developing high-performance NIR RTP materials, while the demonstrated biomedical applications highlight their significant potential for advanced bioimaging and precision diagnostics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3809-y
The development of hydrogels that simultaneously achieve high strength and good toughness remains a critical challenge in soft material science, particularly for applications in flexible electronics, soft robotics, and biomedical devices. Conventional approaches often suffer from a trade-off between mechanical robustness and functional performance. In this work, we present a novel solvent-driven dual-network entanglement strategy to fabricate a strong and tough poly(vinyl alcohol) (PVA)-based organo-hydrogel by synergistically combining isopropanol (IPA) solvent substitution to induce dense polymer chain entanglement and a sodium alginate (SA) ionic crosslinked network as a dynamic energy-dissipation phase. The resulting organo-hydrogel exhibits excellent mechanical performance with a tensile strength of 3.18 MPa and a toughness of 16.65 MJ/m3, representing increases of approximately 17 and 49 times that of conventional PVA hydrogels, respectively. Furthermore, the organo-hydrogel displays superior swelling resistance and long-term stability in aqueous environments, enabling reliable operation in challenging conditions such as underwater motion sensing and wearable strain detection. Morphological analyses reveal the critical role of solvent-mediated chain reorganization and dual-network interactions in achieving these properties. This work not only provides a versatile platform for designing robust gel materials but also offers fundamental insights into solvent-network interactions for advanced soft material engineering.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607009
Resource utilization of food waste is a key measure for implementing waste classification and constructing zero-waste cities in China. However, the technical route based on anaerobic digestion currently faces developmental bottlenecks. In this study, engineering-scale facilities located in Northeast, North, Northwest, and Southeast China were selected, and material flow analysis was employed to comprehensively assess the current status of anaerobic digestion of food waste. The results indicated that, during the pretreatment stage, both leachate and organic slurry from all surveyed regions exhibited high COD/TN ratios, and the leachate contained high concentrations of lipids. Following three-phase (oil-water-solid) separation, the oil recovery rate could reach over 98%. Anaerobic digestion of each ton of food waste from the four regions generated approximately 70 to 80 Nm³ of biogas, while simultaneously producing liquid digestate accounting for 69% to 80% of the total mass and solid digestate accounting for 2.7% to 3.6%. However, the annual continuous production of digestate was not aligned with the seasonal demand for land use, thereby restricting the pathway for resource utilization. Converting food waste into an external carbon source can significantly enhance its resource utilization efficiency, with the economic benefits increasing by more than 203% compared to the methanogenesis pathway. The selection of the carbon source production technology route should be comprehensively determined by taking into account factors such as the specific nitrogen removal requirements of the target wastewater treatment process, the quality requirements for the carbon source products, and the substitution rate of commercial carbon sources.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3920-1
Lead-free halide perovskites are promising scintillators due to strong X-ray attenuation and high internal quantum efficiency (IQE), but their application is hindered by moisture sensitivity. Here, CsSrCl3:Eu2+ nanocrystals were grown in situ in a specially designed inorganic glass matrix. By employing [PO4]-modification and controlled crystallization, a transparent CsSrCl3:Eu2+ glass-ceramic (GC) scintillator was obtained, combining high crystallinity (15.9%) with excellent optical transparency (85.3% at 432 nm). The GC exhibits outstanding photoluminescence (PL) performance, including a high IQE of 87.6% and superior thermal stability (74% intensity retention at 493 K relative to 303 K). Benefiting from the robust glass matrix, the GC retains 99% of its initial PL intensity after 14 days of water immersion. Under X-ray excitation, it shows blue X-ray excited luminescence (XEL), with peak and integrated intensities reaching 117% and 25.1% of those of Bi4Ge3O12 crystal, respectively. The scintillator achieves a high spatial resolution of 20 lp mm−1 and an X-ray detection limit of 3.7 μGy s−1. Furthermore, it demonstrates exceptional operational stability in humid environments, maintaining clear X-ray image contrast even after 48 h of water submersion. This study provides an effective strategy for stabilizing hygroscopic halide scintillators in a durable [PO4]-modified fluoroaluminate glass matrix and demonstrates the potential of CsSrCl3:Eu2+ GC for high-resolution and stable X-ray imaging.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512015
The co-contamination of cadmium (Cd), lead (Pb), and zinc (Zn) in agricultural soils near mining areas poses significant risks to ecosystems and human health. Conventional stabilization materials often exhibit insufficient performance for Zn, particularly in multi-metal systems. This study synthesized a novel composite biochar (PFMBC) by loading phosphate and iron-manganese oxides onto biochar via phosphoric acid impregnation followed by secondary pyrolysis at 600 °C. The stabilization efficiency of PFMBC was evaluated against pristine biochar (BC) and iron-manganese modified biochar (FMBC) in a soil collected from a lead-zinc mining area (total Cd: 43.77 mg·kg−1, Pb: 3355.94 mg·kg−1, Zn: 1296.57 mg·kg−1). After 60 days of incubation with 5% PFMBC, the DTPA-extractable (bioavailable) fractions of Cd, Pb, and Zn decreased by 73.44%, 90.10%, and 69.33%, respectively, significantly outperforming BC and FMBC. Sequential extraction indicated that PFMBC promoted the transformation of Cd, Pb, and Zn from acid-soluble and reducible fractions to more stable residual fractions. Characterization via FTIR, SEM, and XRD revealed enhanced surface functional groups and the formation of stable mineral phases. The synergistic effects of phosphate precipitation, iron-manganese oxide adsorption, and surface complexation contributed to the superior stabilization, particularly overcoming the challenge of Zn immobilization. These findings demonstrate that PFMBC is a promising amendment for the remediation of Cd-Pb-Zn co-contaminated soils, offering high efficiency and long-term stability.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608015
Inter-basin water diversion projects can profoundly alter the water quality dynamics of receiving basins. Taking the Qincun Reservoir and its downstream reaches in the Huangze River Basin as a case study, this research quantitatively evaluates water-quality responses under multiple coordinated management measures. An integrated Environmental Fluid Dynamics Code-Soil and Water Assessment Tool (EFDC-SWAT) modeling framework was established, coupling a two-dimensional hydrodynamic-water-quality model for the reservoir with a hydrology-water-quality model for the downstream reaches. Seven management scenarios were designed to reflect various combinations of point- and non-point-source pollution control strategies. Simulations focused on spatiotemporal variations in key indicators—total nitrogen (TN), total phosphorus (TP), ammonia nitrogen (NH3-N), and permanganate index (CODMn)—and assessed pollution-load reduction effectiveness. Comparative analysis using the comprehensive water quality identification index (CWQII) revealed that under Scenario 3 (highest pollution-control standards with lowest diversion volume), TN and TP concentrations in the reservoir decreased by 80% and 50%, respectively, achieving Class II water-quality standards. Downstream TN and TP levels declined by 36% and 33%, and the CWQII improved from 4.211 to 3.410. Land consolidation contributed 77% and 45% to TN and TP load reductions in the reservoir, respectively, while a 20% reduction in diversion volume was most effective in improving downstream TN (>50%). These results demonstrate that the coupled EFDC-SWAT model effectively elucidates mechanisms through which inter-basin water diversion influences water quality in supply areas. Moreover, synergistic point- and non-point-source controls exhibit a nonlinear enhancement effect on overall water-quality improvement.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60686-X
This study reports a streamlined route for synthesizing plate-like α-Al2O3 via co-combustion activation of coal gangue and corn stalk, enabling high-value utilization of solid wastes. The introduction of corn stalk significantly reduces the apparent activation energy of coal gangue combustion and increases the acid leaching yield of aluminum to 81.9%. Mechanism analysis reveals that titanium and iron ions in the co-combustion ash leachate act as natural morphology regulators, facilitating the formation of a plate-like structure in the alumina product, with titanium exhibiting leaching behavior consistent with that of aluminum. Furthermore, a high content of AlO6 structural units in the precursor effectively promotes the direct conversion into dense α-Al2O3 crystals during thermal treatment, thereby enhancing product density. Under optimized conditions (800 °C, 1 h), the as-prepared α-Al2O3 exhibits a plate-like morphology, with a median particle size (d50) of 5.70 μm and a density of 4.94 g/cm3. This work provides a new approach for the synergistic resource utilization of coal gangue and biomass waste.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60668-8
A series of Co-based molecular sieve catalysts with varying Si/Al ratios was synthesized via impregnation. Microstructural properties of Co active sites were characterized by XRD, TEM, Raman, H2-TPR, Py-FTIR, and XPS. Results indicate that surface Co species predominantly exist as CoOx nanoclusters and isolated Co2+, with the latter exhibiting superior N2O decomposition activity. Decreasing the Si/Al ratio of the MFI zeolite promotes the formation of isolated Co2+ active sites, thereby enhancing catalytic performance. Compared to Co/S-1 (pure silica support), the Co/HZ60 catalyst (low Si/Al ratio ZSM-5) lowers the temperature for complete N2O decomposition by 80 °C and demonstrates excellent resistance to O2 and NO. The strong interaction between the zeolite framework and Co2+ inhibits oxidation to Co3+, improving N2O adsorption and activation. This work provides a rational design strategy for efficient and stable Co-based catalysts for N2O abatement in industrial tail gases.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4104-4
Covalent organic frameworks (COFs) are promising adsorbents for gas adsorption and separation, yet identifying optimal structures among their vast design space requires efficient high-throughput screening. Conventional machine-learning predictors rely heavily on specific gas-related features, which are time-consuming and limit scalability, leading to inefficiency and labor-intensive processes. Here, we propose COFAP, a universal COFs adsorption prediction framework that extracts multi-modal structural and chemical features via deep learning and fuses these complementary features through a cross-modal attention mechanism. Without relying on explicit gas-specific thermodynamic descriptors, COFAP achieves state-of-the-art prediction performance on the hypoCOFs dataset under the conditions investigated, outperforming existing approaches. Based on COFAP, we found that high-performing COFs for gas separation concentrate within a narrow range of pore size and surface area. A weight-adjustable prioritization scheme is also developed to enable flexible, application-specific ranking of candidate COFs. Superior efficiency and accuracy render COFAP directly deployable in crystalline porous materials.