SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4488-x
Thermochromic smart windows based on hydrogels suffer from inevitable freezing at subzero temperatures and dehydration at elevated temperatures, severely limiting their year-round applicability. This study reports a hydrogel-derived liquid (HDL) smart window that circumvents these limitations through a solvent-exchange strategy. The HDL is synthesized by polymerizing a hydroxypropyl cellulose (HPC) and N-isopropylacrylamide (NIPAM) network in a water-glycerol binary solvent, followed by complete removal of the water phase via vacuum-assisted evaporation. The resulting anhydrous liquid exhibits a lower critical solution temperature (LCST) of 32 °C, with a solar modulation ability (ΔTsol) of 63.2% and a luminous transmittance (Tlum) of 88.1% in the clear state. Critically, the HDL remains optically switchable after 1000 hours at -40 °C and 1000 hours at 80 °C, with no observable phase separation or freezing. The smart window prototype demonstrates a 12.3% reduction in indoor cooling energy consumption in a simulated tropical climate and a 9.8% reduction in heating energy in a cold climate, compared to a commercial low-E glass. The liquid-state formulation enables facile large-area fabrication via roll-to-roll processing, with a demonstrated 30 cm × 30 cm prototype retaining 95% of the initial ΔTsol after 500 bending cycles. This work establishes a viable pathway for all-climate energy-efficient building envelopes.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4303-7
Sodium-ion batteries (SIBs) are promising for grid-scale storage and low-speed electric vehicles, yet their electrochemical behavior is governed by intricate mechanical-electrochemical coupling effects, rendering failure mechanisms not fully understood. Here, we develop an in-situ pressure-electrochemical monitoring system and reveal the failure mechanism of commercial Ah-level NaNi1/3Fe1/3Mn1/3O2//hard carbon (NNFMO//HC) sodium-ion pouch cells. Under an initial external pressure of 500 kPa, the full cell retains 90.07% of its capacity after 500 cycles at 0.5 C. Operating at the optimal pressure of 500 kPa effectively avoids heterogeneous sodium deposition in HC anodes, suppresses gas evolution from electrolyte decomposition, and prevents irreversible phase transitions in NNFMO cathodes during long-term cycling, thereby mitigating capacity degradation. Deviation from this optimal pressure leads to spatially non-uniform sodium deposition, accelerated electrolyte decomposition, and irreversible cathode phase transitions, collectively accelerating capacity fade. This work establishes a quantitative relationship between external pressure and pouch cell degradation, advancing SIBs development and application.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3630-2
This study demonstrates a dual-interface engineering approach for performance enhancement in perovskite-silicon tandem solar cells. By applying ethylenediamine dihydroiodide (EDAI2) to simultaneously modify both top and bottom interfaces of wide-bandgap perovskite layers, we achieve synergistic defect suppression and charge transport optimization. Time-resolved photoluminescence characterization reveals extended carrier lifetimes and improved spatial homogeneity in dual-modified perovskite films. The optimized single-junction wide-bandgap (>1.66 eV) perovskite solar cells attain a champion efficiency of 22.75% with enhanced operational stability. Implemented in perovskite-silicon tandem configuration, the devices achieve over 31% power conversion efficiency, validating the effectiveness of organic ligand-mediated dual-interface engineering in regulating carrier dynamics and advancing perovskite-based tandem photovoltaics.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3789-x
Wearable sensors have attracted significant attention due to their superior sensitivity, safety, and adaptability compared with conventional detection technologies. However, developing sustainable sensing materials that combine excellent performance with environmental friendliness remains a significant challenge. In this study, Juncus effusus (JE), a natural fiber featuring a unique internal three-dimensional (3D) network structure, was employed as the substrate. Conductive polyaniline was loaded onto the JE structure to impart electrical conductivity, and Ecoflex encapsulation provided high elasticity. Based on this approach, a JE-based resistive flexible sensor (PHE-JE) was successfully fabricated. The PHE-JE sensor exhibits high stability under various strain conditions, along with excellent flexibility and durability. Moreover, benefiting from its complex 3D structure and synergistic material interactions, the PHE-JE sensor enables accurate detection of diverse motion types, showing promising potential for future wearable sensing applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3671-0
Photothermal therapy (PTT) is a non-invasive tumor treatment that offers controllability, non-drug resistance, and precise ablation, yet its efficacy is limited by uncontrolled heat diffusion and weak immune responses, often leading to metastasis. Here, we report a chondroitin sulfate-modified Prussian blue-montmorillonite immunoregulator (PM@CS) that integrates tumor cell adhesion and Golgi targeting to confine photothermal damage at the organelle level. PM@CS accumulates on the Golgi apparatus, reducing heat transfer distance and enhancing photothermal ablation. This targeted hyperthermia disrupts post-translational modification and secretion of metastasis-associated proteins, with GOLPH3 and GOLM1 expression reduced by 63.4% and 70.3%, respectively. Furthermore, PM@CS promotes dendritic cell maturation (3.3-fold increase in CD80+ and CD86+ populations) and enhances antigen-specific CD4+ and CD8+ T cell proliferation, attributed to the immunoadjuvant properties of montmorillonite. Notably, PM@CS upregulates voltage-gated calcium channels (CaV) and enhances Ca2+ influx, activating calcium signaling cascades that amplify immunotherapy. This synergistic approach inhibits primary tumor growth and lung metastasis, offering a promising strategy for cancer treatment.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605007
Reservoirs are significant sources of nitrous oxide (N2O), a potent greenhouse gas. The nosZ-type denitrifying bacteria, which reduce N2O to inert N2, play a critical role in mitigating emissions. This study investigated the community structure, diversity, and abundance of nosZ-type denitrifiers in surface sediments (0-15 cm) from 18 reservoirs in the northeastern Qinghai-Tibet Plateau, including 10 in the Yellow River mainstem and 8 in the Huangshui River basin. Sampling occurred during dry (May 2023) and wet (August 2023) seasons. High-throughput sequencing of the nosZ gene and quantitative PCR were employed. Results showed that Proteobacteria dominated (78.91%). Paracoccus and Halomonas were biomarkers in the Yellow River mainstem. Diversity was significantly higher in the Huangshui basin (P<0.05), with no temporal difference. Gene abundance was higher in the Huangshui basin (165.24×10^5 copies/g) than in the Yellow River mainstem (34.43×10^5 copies/g), and higher in wet season (128.55×10^5 copies/g) than dry season (61.27×10^5 copies/g) (P<0.05). Redundancy analysis and hierarchical partitioning identified sediment temperature, pH, total phosphorus, and water total nitrogen as key drivers, explaining 17.14%, 16.89%, 13.83%, and 11.23% of community variation, respectively. These findings reveal significant spatiotemporal heterogeneity and provide a scientific basis for N2O mitigation in plateau reservoirs.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025092801
Urban river water quality is critically influenced by outfall discharges, yet the seasonal dynamics of dissolved organic matter (DOM) and its linkage to water quality remain poorly constrained. This study collected outfall water samples seasonally during 2023–2024 along the Nanfei River and Banqiao River in Hefei, Anhui Province. Parallel factor analysis of excitation-emission matrices identified three fluorescent components: fulvic acid-like C1, tryptophan-like (protein-like) C2, and terrestrial humic-like C3. Seasonal variations were pronounced: protein-like C2 dominated in winter and spring, whereas summer and autumn showed lower C2 proportions due to rainwater dilution and urban nonpoint source runoff inputs. Water quality indices decreased in summer and autumn, primarily attributed to dilution by rainfall runoff. Fluorescence index (FI > 1.9) and biological index (BIX > 1.0) indicated predominantly autochthonous DOM sources. During summer and autumn, humification index (HIX) and specific UV absorbance (SUVA) increased, while spectral slope ratio (SR) decreased, suggesting enhanced terrestrial and urban runoff influence. Significant positive correlations were observed between protein-like C2 and terrestrial humic-like C3 with water quality parameters, indicating their utility as precise indicators of pollution sources and seasonal water quality variations. These findings provide a scientific basis for integrated management of urban outfalls.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025032001
This study investigates the variation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and their monomer components during low-temperature thermal decomposition (250–500 °C) of municipal solid waste incineration fly ash from a typical mechanical grate furnace. Results demonstrate that pyrolysis temperature and time significantly affect the solid-phase removal rates of PCDD/F mass concentration and toxic equivalent (TEQ) concentration. The influence weights of temperature on mass and TEQ removal rates are 20.86 and 21.41, respectively, while those of time are 4.27 and 3.36. Response surface analysis identifies optimal conditions at 380 °C for 1.0 h. At 250–300 °C, both PCDFs and PCDDs concentrations increase synchronously, indicating enhanced formation. At 300 °C for 2.0 h, high-chlorinated congeners undergo dechlorination to low-chlorinated ones, notably increasing 2,3,7,8-T4CDD (I-TEF=1.0) and 1,2,3,7,8-P5CDD (I-TEF=0.5). From 350 °C upward, significant degradation occurs; at 380 °C (1.0 h), degradation rates for PCDDs and PCDFs reach 97.8% and 97.6%, respectively, effectively reducing TEQ-contributing congeners. The process proceeds in two stages: initial dechlorination, followed by destruction of dioxin-like compounds at higher temperatures. 2,3,7,8-T4CDD emerges as a critical component for detoxification. These findings provide a scientific basis for optimizing thermal treatment of fly ash to minimize environmental and health risks.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025051802
This study investigates the recovery of nitrogen and phosphorus from anaerobic digestion biogas slurry of chicken manure via magnesium-modified zeolite coupled with electrochemical precipitation crystallization. Three types of magnesium-modified zeolites were prepared using alkali activation and magnesium loading to enhance adsorption capacity. A coupled 'magnesium-modified zeolite-electrochemical MAP' reactor was constructed, and key parameters (N/P ratio, pH, current density) were optimized via response surface methodology. The results show that MgCl2-modified zeolite (MgCl2-ZO) exhibited the best coupling precipitation performance. Under optimal conditions (N/P ratio 3.78, pH 8.43, current density 13.11 A·m−2), the removal efficiencies for total nitrogen (TN), total ammonium nitrogen (TAN), total phosphorus (TP), and total phosphate (TPS) reached 54.84%, 62.93%, 82.02%, and 77.72%, respectively. The mechanism involves synergistic adsorption and electrochemical release of Mg2+ from the magnesium electrode, which promotes struvite crystallization. The electrochemical field enhances ion exchange and chemical precipitation on the zeolite surface, facilitating efficient nutrient recovery. This approach offers a promising solution for nutrient management in livestock wastewater.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3991-3
Ionic covalent organic frameworks (ICOFs), as an emerging subclass of covalent organic frameworks (COFs), have garnered significant attention owing to their unique integration of structural precision and ionic functionality. Although conventional neutral COFs possess excellent crystallinity, tunable porosity, and high stability, their limited electronic tunability and poor charge-transport properties have constrained their performance in various applications. The incorporation of ionic sites into COF skeletons or pore environments effectively overcomes these intrinsic limitations. The presence of charged centres enhances framework polarity, modulates local electrostatic fields, and facilitates efficient ion migration and charge separation, thereby endowing ICOFs with superior functionality. As a result, ICOFs have demonstrated remarkable potential in diverse fields, including adsorption, sensing, ion conduction, energy devices, photocatalysis, and electrocatalysis. This review provides an integrative perspective by systematically linking framework design, ionic site engineering, structure-property relationships, and functional performance in various applications, highlighting ICOFs distinct advantages over neutral COFs and providing fundamental insights for the rational design of next-generation ionic frameworks toward energy and environmental applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4052-0
Cutaneous wound infections affect millions of patients annually worldwide, and early diagnosis is critical for timely anti-infection treatment. Bacterial infections alter wound pH, offering a promising diagnostic approach. Here, a diagnostic smart dressing (CMC-PDBI) is developed by ultraviolet-initiated crosslinking of a pH-responsive indicator coating, incorporating modified bromothymol blue, onto a carboxymethyl cellulose substrate. The dressing exhibits superior pH-triggered color-changing performance in both phosphate buffer solution and bacterial cultures across the pH range associated with wound infection (orange at pH 6.0, green from pH 6.5 to 7.5, blue at pH 8.0). In a murine wound infection model, CMC-PDBI indicates infection two days before symptomatic manifestation. Early therapy guided by the dressing accelerates wound healing and reduces inflammation. A smartphone application (InfectSense) assists in identifying infection risk. This work presents a novel early-warning platform for qualitative visual diagnosis of wound infections before clinical symptom onset, with high potential for clinical and home care settings.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4103-8
The industrial production of urea through the integrated Haber–Bosch and Bosch–Meiser processes involves high energy consumption and significant CO2 emissions. Given the persistent technical challenges inherent in direct electrocatalytic methods, catalytic systems that enable the thermal coupling of N2 and CO2 under mild conditions represent a promising and sustainable approach to urea synthesis. Herein, we designed MXene-based bimetallic single-cluster catalysts, M1Ru3@Mo2CO2, in which the M1Ru3 cluster is stably anchored on the Mo2CO2 support. Using density functional theory calculations, we systematically evaluated the structural stability and adsorption capabilities of 3d transition metal variants (M = Sc to Zn) toward N2, CO2, and H2. The results demonstrate that Co1Ru3@Mo2CO2 exhibits excellent thermodynamic stability and enables the synergistic activation of N2, CO2, and H2, fulfilling the prerequisite conditions for catalyzing the direct coupling of N2 and CO2 to form urea. Further analysis reveals that Co1Ru3@Mo2CO2 efficiently promotes the direct thermal coupling of N–C into urea under mild conditions via the associative pathway, with the rate-determining step corresponding to the conversion of *NHNH2 → *NH2NH2 with the low energy barrier of 1.16 eV. Under realistic conditions of 780 K and 29 bar, the calculated turnover frequency reaches 1.01 × 10−3 s−1 site−1. The high catalytic performance arises from the ability of the Co1Ru3 bimetallic cluster to precisely modulate charge transfer between support and reaction intermediates. Moreover, the in situ generated NH2 species acts as an autocatalyst for CO2 hydrogenation, while the cluster selectively enhances the electrophilicity of the *CO intermediate, thereby facilitating the nucleophilic attack by *NH2 and ensuring efficient C–N bond formation. The finding of the outstanding performance of Co1Ru3@Mo2CO2 single cluster catalysts could bypass the energy-intensive NH3 synthesis step, reduce overall energy demand, and remain compatible with existing urea production infrastructure, thereby offering significant scientific and technological significance.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4150-2
Bacterial infection and irregular wound morphology are major challenges in clinical wound management. Injectable hydrogels can conform to irregular wound geometries but often lack antimicrobial activity. Here, we report an injectable hydrogel (HPAu gel) formed by sequentially mixing phenylboronic acid-modified hyaluronic acid (HA-PBA) and chloroauric acid under alkaline conditions. The gel's internal multiple crosslinks enable uniform encapsulation of in situ-generated gold nanoparticles. Hydrogen bonds and phenylboronic acid ester bonds confer self-healing, injectability, and adhesion, allowing effective sealing of irregular cavities. In vitro, the hydrogel exhibits long-lasting photothermal stability and eliminates multiple bacterial strains. In a mouse dorsal full-thickness infected wound model, HPAu gel under near-infrared (NIR) irradiation eradicated Staphylococcus aureus, reduced inflammation (TNF-α fluorescence area significantly lower; IL-10 area 12.88‰ vs <2‰ in Blank), promoted vascular regeneration (CD31 and α-SMA expression increased), and accelerated wound healing. This work presents a promising strategy for treating irregular infected wounds.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3587-4
Unstable zinc interfaces arising from dendrite growth and parasitic reactions impede the practical deployment of rechargeable aqueous zinc-ion batteries. This study introduces 1-(2-pyridylazo)-2-naphthol (PAN) as a parts-per-million (ppm) level electrolyte additive to stabilize the Zn anode. Theoretical and experimental analyses reveal that PAN undergoes parallel adsorption on the Zn surface, establishing strong π-π interactions between adjacent molecules that efficiently repel water. The OH, pyridine N, and azo N groups in PAN chelate Zn2+, modulating Zn2+ diffusion and promoting uniform deposition while suppressing dendrite formation. A 10 ppm (0.04 mM) PAN addition extends the lifespan of a symmetrical cell to 1500 h at 2 mA cm−2 and 1 mAh cm−2. The Zn||Cu half-cell achieves a Coulombic efficiency of 99.91% over 3500 cycles at 5 mA cm−2 and 1 mAh cm−2. Full cells with NH4V4O10 and MnO2 cathodes exhibit enhanced cycling stability. Notably, a Zn||NH4V4O10 pouch cell retains 71.1% capacity after 250 cycles at 0.8 A g−1. This work demonstrates a viable strategy for selecting high-efficiency additives for aqueous metal-based batteries.