SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4367-4
Single-crystalline Cs3Cu2I5 has attracted considerable interest owing to its excellent scintillation performance and favorable stability. Nevertheless, second phases induced by peritectic reactions during melt growth give rise to deteriorated scintillation properties and promote crystal cracking. In this work, the effects of non-stoichiometric ratios of raw material (n(CsI)=0.57, 0.62, and 0.63) on the crystallization behavior and scintillation properties were systematically investigated. The results show that the crystal quality is optimal at n(CsI)=0.62, featuring high transparency, absence of macroscopic inclusions, and cracking free, with a PLQY of 79.3%. Temperature-dependent photoluminescence verifies the self-trapped exciton emission mechanism with strong exciton-phonon coupling, giving an exciton binding energy of 473.9 meV and a Huang-Rhys factor S of 79.8. The as-grown crystal exhibits an optimized light yield of 24,380 photons/MeV, an energy resolution of 3.8% for 137Cs (662 keV) γ-rays, a dominant decay time of 957 ns, and excellent linear response in the medium-to-high energy region. Precise regulation of the raw material stoichiometry can effectively suppress the formation of second phases, yielding high-quality Cs3Cu2I5 single crystals whose comprehensive performance demonstrates promising application potential in γ-ray detection.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3725-1
Conductive hydrogel-based stretchable electronics have been extensively investigated, with strain sensors being the most prominently studied. While mechanical properties significantly affect device performance, the systematic correlation between specific mechanical parameters and sensing performance remains rarely explored. This work compares the influences of Young’s modulus and mechanical hysteresis on sensing performance between highly entangled PAM-Li and double-network PAM-Li-Agar-3 strain sensors. Owing to the brittle agar network, which imparts a higher Young’s modulus and pronounced mechanical hysteresis to the double-network PAM-Li-Agar-3 hydrogel, the corresponding sensor requires a greater driving force for deformation and yields signals with poor reproducibility. In contrast, the PAM-Li hydrogel, characterized by highly entangled polymer chains, exhibits a lower Young’s modulus and negligible mechanical hysteresis. Consequently, signals from the PAM-Li strain sensor demonstrate enhanced sensitivity and stability. Therefore, this work demonstrates that a low Young’s modulus and minimal mechanical hysteresis are critical factors for achieving superior sensing performance in strain sensors, as systematically validated through comparative analyses across diverse application scenarios.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507043
Municipal sludge with high moisture content and strong viscosity tends to form a dense crust during conventional rotary drum drying, reducing heat and mass transfer efficiency and prolonging drying time. This study proposes a thermal steel ball-enhanced rotary drum drying method that introduces high heat capacity, high thermal conductivity steel balls to achieve synergistic contact heat conduction and mechanical disturbance. An evaluation system incorporating dimensionless moisture ratio (MR), drying rate (DR), characteristic drying time (tdry), effective moisture diffusivity (Deff), and volumetric evaporation intensity (U) was established. Results show that compared with conventional drying, steel ball-enhanced drying increased maximum drying rate (DRmax) by 22.59%–41.19%, U by 38.06%–93.43%, and shortened tdry by 27.56%–48.30%, with more pronounced advantages under high load conditions. Deff was significantly higher throughout the process, with maximum increase up to 48.30%, indicating that ball rolling and collision effectively disrupt the crust and promote moisture migration. Mechanistic analysis reveals that the performance enhancement arises from the dual action of thermal-mechanical coupling and mechanical disturbance, which enhances local heat flux via contact conduction and dynamically renews the drying interface, shortening diffusion paths. This study elucidates the heat and mass transfer mechanisms of thermal steel ball-enhanced sludge drying, providing theoretical support and technical reference for efficient sludge volume reduction and dryer design optimization.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025121001
Ion chromatography (IC) is the core analytical method for qualitative and quantitative determination of anions in complex water environments, and its separation efficiency highly depends on the performance of the stationary phase. This review systematically summarizes recent progress in the preparation and functionalization of IC stationary phases, addressing the urgent need for high selectivity and sensitivity in water anion analysis. The characteristics of organic polymer-based and inorganic-based matrices are compared, highlighting the advantages of polymer matrices such as poly(methacrylate), poly(vinyl alcohol), polystyrene-divinylbenzene (PS-DVB), and ethylvinylbenzene-divinylbenzene (EVB-DVB) in terms of wide pH tolerance (e.g., pH 0–14 for PS-DVB) and organic solvent compatibility, which allow the use of strong acid or base eluents. Various functionalization strategies are discussed, including the introduction of quaternary ammonium groups, hydrophilic modifications, and grafting of functional layers, which enhance separation selectivity and detection capability. The review also covers the development of hybrid stationary phases and the application of IC in monitoring trace pollutants in water, such as bromate, chlorite, chlorate, fluoride, and nitrate, as regulated by Chinese standards (GB 5749—2022). Future trends are projected, focusing on novel materials for precise identification and high-throughput monitoring. The paper provides a comprehensive reference for the design of high-performance stationary phases, emphasizing the importance of matrix selection and surface chemistry in achieving robust and sensitive anion analysis.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604004
Tire wear particles (TWPs) are emerging pollutants and constitute the dominant type of microplastics (MPs) in urban stormwater runoff, accounting for up to 90% of MPs in some cases. They are characterized by small size, high mobility, complex composition, and significant toxicity. Current research on TWPs remains fragmented, lacking a comprehensive understanding of their environmental behaviors and pollution control in aquatic systems. This review systematically analyzes the enrichment and vectoring roles of TWPs for coexisting pollutants, and their environmental fate, including ecotoxicological impacts, detection methodologies, release of intrinsic additives, and aggregation and sedimentation behaviors. Drawing on insights from other microplastic studies, the paper explores control technologies across the pollution pathway—source, transport, and terminal treatment—and proposes feasible management strategies. Key findings indicate that TWPs can adsorb heavy metals and organic contaminants, with adsorption capacities influenced by aging processes. Their aggregation is governed by solution chemistry, with critical coagulation concentrations varying with ionic strength and pH. The release of additives such as zinc and benzothiazoles is significant, posing ecological risks. Future research should focus on real-water aggregation mechanisms, additive release under natural conditions, long-term performance of treatment facilities like constructed wetlands under TWPs stress, enzymatic degradation pathways, and integration of AI, big data, and IoT for cost-effective detection and risk modeling. This review provides a scientific basis for developing targeted pollution control measures for TWPs in aquatic environments.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025010604
Groundwater is a vital component of Beijing's water supply, yet elevated sulfide concentrations restrict its utilization. This study employed principal component analysis (PCA) and absolute principal component-multiple linear regression (APCS-MLR) to apportion sulfide sources and quantify their contributions in the middle and lower reaches of the Chaobai-Wenyu alluvial-proluvial fan. Sulfur and oxygen isotopes (δ34S and δ18O) were used to identify sulfate sources and discern anthropogenic versus natural influences. Results showed that high-sulfide groundwater predominantly occurred in Na-type water, with sulfide accumulation from desulphidation widespread, particularly in Shunyi and within the first, second, and third aquifers, independent of wet/dry seasons. Isotopic analysis indicated sulfate mainly originated from evaporite dissolution, and sulfides from desulphidation were of geological background origin. PCA extracted four principal components: leaching-enrichment (F1), natural dissolution of iron-manganese oxides (F2), water desulphidation (F3), and CaF2 dissolution equilibrium (F4). F3 exhibited the highest factor loading for sulfide (0.418), while other components had small negative loadings. APCS-MLR revealed F3 contributed 21.32% of sulfide, while indigenous sources (e.g., acid-volatile sulfide dissolution, elemental sulfur disproportionation, geothermal activity, well casing materials) contributed 63.66%. Overall, sulfide in the study area is a geological background factor, with limited anthropogenic influence.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3819-7
Selective solar-driven aerobic oxidation of biomass derivatives into valuable chemicals under ambient conditions is pivotal for sustainable chemical manufacturing but faces challenges from the conflict between O2 activation kinetics and selective C–H bond cleavage. This work demonstrates a spatial decoupling strategy in a precisely-engineered 2D/2D g-C3N4/ZnIn2S4 architecture, where ZnIn2S4 domains selectively activate O2, while adjacent g-C3N4 modulates electron transfer to O2 and tailors 5-hydroxymethylfurfural (HMF) binding configuration for selective C–H bond cleavage. This enables efficient selective conversion of HMF to 2,5-diformylfuran (DFF) via ambient aerobic photooxidation. When used alone, ZnIn2S4 produces mixed reactive oxygen species (·O2−/·OH) due to uncontrolled electron transfer during O2 activation. In-situ spectroscopy, Kelvin probe force microscopy (KPFM) and density functional theory (DFT) calculations demonstrate that the 2D/2D heterojunction, driven by its directed electric field, selectively activates O2 into ·O2− at ZnIn2S4 domains while suppressing ·OH generation by moderate electron transfer, mitigating over-oxidation. Adjacent g-C3N4 domains precisely anchor HMF via –OH group interactions, steering selective DFF formation. This spatial decoupling achieves a remarkable HMF-to-DFF photo-conversion rate of 1517.5 μmol g−1 h−1 with 99.4% selectivity under ambient air, outperforming many reported state-of-the-art catalysts and maintaining durable cycling performance. The work establishes a spatial decoupling principle to overcome O2 activation kinetics and site competition thermodynamics, paving the way for advanced catalyst design for sustainable energy and the environment.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3774-3
Lithium-air capacitor batteries (LACBs) integrate the rapid charge-discharge capability of supercapacitors into conventional lithium-oxygen batteries, significantly enhancing power density. However, their cycling stability remains unsatisfactory. In this study, we incorporated redox mediators (RMs) into an LACB featuring a dual-cathode configuration. This design facilitates sustained electron transfer between the electrode and Li2O2/Oxygen, thereby delaying RM deactivation caused by electrode passivation and improving overall electrochemical performance. The RM-enhanced battery achieved over 250 cycles at 2 mA cm−2 with a limited capacity of 0.5 mAh cm−2, while exhibiting a 0.54 V reduction in charging voltage at 0.1 mA cm−2 compared to the RM-free system. Furthermore, application of an aluminum foil sealing technique enabled a power density of 13.8 mW cm−2 at 6 mA cm−2, overcoming mass transport limitations inherent in open-cell configurations. We also investigated the influence of oxygen barrier films with varying barrier capabilities on LACB performance. Results indicate that films with superior oxygen resistance better maintain a clean capacitor electrode surface, thereby providing more stable electron supply to the RMs and enhancing rate capability and cycling performance. These findings underscore the potential of redox mediators in improving the performance and longevity of LACBs, offering a promising strategy for their future development.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608013
Eutrophication and cyanobacterial blooms threaten aquatic ecosystems and drinking water safety globally. This study evaluated the efficacy of a compound algicide (PQGA-126, PAC, and red soil) combined with submerged plants (Vallisneria natans and Hydrilla verticillata) for suppressing blooms and restoring eutrophic water. Indoor static experiments used algae-laden water from Nanhu Lake, Gongqingcheng, Jiangxi. Six treatments were established: control, V. natans alone, H. verticillata alone, algicide alone, algicide + V. natans, and algicide + H. verticillata. Results demonstrated that combined treatments significantly reduced total nitrogen (TN), total phosphorus (TP), chlorophyll-a (Chl-a), and turbidity, markedly lowering eutrophication within a short period. The combined approach outperformed single-plant treatments, with algicide + V. natans achieving the greatest reduction in the comprehensive trophic state index. Additionally, the algicide significantly enhanced V. natans growth rate and H. verticillata catalase (CAT) activity, indicating species-specific physiological responses. These findings suggest that integrating compound algicide with submerged plants, particularly V. natans, offers a promising strategy for rapid and effective eutrophic water remediation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4014-3
Laser-induced graphene (LIG) methods, including photothermal and photochemical approaches, are promising for flexible electronics yet face distinct limitations. Photothermal methods often produce graphene with uncontrolled structural and functional properties, while photochemical methods are restricted to a narrow range of precursors. To address these limitations, we propose a pressure-driven LIG (P-LIG) method that uses transient laser-generated pressure fields as an additional control parameter to improve graphene quality. An integrated framework combining ultrafast pump–probe interferometric imaging, large-scale molecular dynamics (MD) simulations, and explainable artificial intelligence (XAI) was developed to investigate this approach. Time-resolved measurements reveal the generation of transient pressure fields during femtosecond laser irradiation of polyimide films, confirming pressure as an intrinsic feature of the process. MD simulations under controlled pressure conditions demonstrate that pressure promotes the nucleation and stacking of graphene layers, resulting in more continuous and planar graphitic networks. XAI analysis quantitatively identifies the important contributions of pressure. These results confirm that the transient pressure introduced by the P-LIG method plays a key role in promoting more ordered, continuous, and planar graphene networks, and enhancing structural integrity and material quality beyond traditional methods. This provides a practical pathway for improving the performance and reliability of LIG-based flexible electronic devices.