SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4479-8
The von Neumann architecture is increasingly constrained by energy consumption and data-transfer efficiency as artificial intelligence and data-intensive applications expand. Neuromorphic computing, inspired by the human brain's information-processing mechanisms, offers an alternative paradigm. Two-dimensional (2D) ferroelectric materials are promising candidates due to their intrinsic non-volatility, atomic-scale thickness, ultra-low power consumption, excellent fatigue endurance, and dangling-bond-free surfaces. This review examines recent advances in 2D ferroelectric materials and associated device architectures for neuromorphic applications. It first introduces ferroelectric mechanisms and representative 2D ferroelectrics, then surveys key device architectures including ferroelectric tunnel junctions, diodes, transistors, and photovoltaic devices. Their applications in in-memory computing and in-sensor neuromorphic systems are discussed, with emphasis on artificial neural networks, spiking neural networks, reservoir computing, and neuromorphic perception for efficient information processing and intelligent sensing. The unique properties of 2D ferroelectrics enable integrated sensing, memory, and computing functionalities, demonstrating potential for future neuromorphic and brain-inspired intelligent systems.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3738-1
The escalating demand for intelligent and functional textiles, driven by technological advancements, has shifted focus from conventional attributes like warmth and aesthetics to smart functionalities. Natural biomass-derived polysaccharides, owing to their biocompatibility, biodegradability, renewability, and unique chemical structures, are pivotal for next-generation flexible wearable smart textiles. This review systematically outlines common natural polysaccharides (e.g., cellulose, chitosan, starch, alginate) used in such textiles, detailing their structural features and modification strategies. It critically evaluates current fabrication methods, highlighting their advantages and limitations. The performance characteristics, action mechanisms, and application scenarios of polysaccharide-based smart textiles are examined, with emphasis on healthcare, motion tracking, smart clothing, and energy storage/management. The review concludes by addressing existing challenges and proposing future directions for integrating polysaccharide materials into smart textile systems, aiming to guide the development of efficient, green flexible wearable devices.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3674-2
Enhancing catalytic activity is a core objective in catalyst design, with active site accessibility being a critical determinant. Polyoxometalate-based metal-organic complexes (POMOCs), combining advantages of POMs and MOCs, offer potential for constructing catalysts with highly accessible active sites. In this study, a series of POMOCs were synthesized using different POM templates: [CoII1.5(L)1.5(PMo12O40)(H2O)4]·3H2O (Co-PMo12), [CoII1.5(L)1.5(PW12O40)(H2O)4]·3H2O (Co-PW12), [CoII2(L)2(SiW12O40)(H2O)4]·11H2O (Co-SiW12), and H[CoII2.5(L)3(P2W18O62)(H2O)8]·10H2O (Co-P2W18). These were characterized by FT-IR, PXRD, and single-crystal X-ray diffraction. Catalytic activity differences for olefin epoxidation were attributed to distinct accessibility of Co(II) sites upon thermal activation. Notably, Co-P2W18 achieved 99% yield of 1,2-epoxycyclooctane within 3 hours at room temperature using O2 as oxidant, owing to highly accessible unsaturated Co(II) sites. This performance is superior to most reported catalysts. The reaction mechanism was investigated using density functional theory. The catalyst exhibited excellent stability over five cycles, with FT-IR, PXRD, and XPS confirming structural and oxidation state integrity. This work highlights the potential of POMOCs in designing catalysts with highly accessible active sites for enhanced catalytic activity.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507043
Municipal sludge with high moisture content and strong viscosity tends to form a dense crust during conventional rotary drum drying, reducing heat and mass transfer efficiency and prolonging drying time. This study proposes a thermal steel ball-enhanced rotary drum drying method that introduces high heat capacity, high thermal conductivity steel balls to achieve synergistic contact heat conduction and mechanical disturbance. An evaluation system incorporating dimensionless moisture ratio (MR), drying rate (DR), characteristic drying time (tdry), effective moisture diffusivity (Deff), and volumetric evaporation intensity (U) was established. Results show that compared with conventional drying, steel ball-enhanced drying increased maximum drying rate (DRmax) by 22.59%–41.19%, U by 38.06%–93.43%, and shortened tdry by 27.56%–48.30%, with more pronounced advantages under high load conditions. Deff was significantly higher throughout the process, with maximum increase up to 48.30%, indicating that ball rolling and collision effectively disrupt the crust and promote moisture migration. Mechanistic analysis reveals that the performance enhancement arises from the dual action of thermal-mechanical coupling and mechanical disturbance, which enhances local heat flux via contact conduction and dynamically renews the drying interface, shortening diffusion paths. This study elucidates the heat and mass transfer mechanisms of thermal steel ball-enhanced sludge drying, providing theoretical support and technical reference for efficient sludge volume reduction and dryer design optimization.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2024112101
The biological reduction of Cr(VI) to less hazardous Cr(III) is a promising strategy for remediating Cr(VI)-contaminated sites. Both biochar and riboflavin can act as electron shuttles to accelerate this bioreduction process, yet their combined effects remain poorly understood. Using Shewanella oneidensis MR-1 as a model reducing bacterium, we investigated the joint influence of biochar (average particle size 28.85 μm) and riboflavin at high (1 mmol·L−1) and low concentrations on Cr(VI) bioreduction. Individually, biochar and high-concentration riboflavin enhanced indirect electron transfer, accelerating Cr(VI) removal. However, when combined, the fast-phase reaction rate (rf0) did not significantly improve compared to single amendments. The combined action factor revealed an antagonistic inhibition between biochar and riboflavin. Mechanistically, high-concentration riboflavin saturated biochar's adsorption sites (equilibrium concentration 0.96±0.04 mmol·L−1), hindering biochar's role as an electron conduit. With a bacterial density of 3.4×10^7 cells·mL−1, the inter-bacterial distance (30.87 μm) exceeded biochar's particle size, and the per-cell riboflavin concentration (2.9×10−2 pmol·cell−1) was sufficient for riboflavin to dominate as the primary electron shuttle, while biochar's surface became coated, reducing its efficacy. These findings reveal the complex interplay between biochar and soluble organic matter in Cr(VI) bioreduction, underscoring the need to consider such antagonistic effects when designing bioremediation strategies for multi-component contaminated environments.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3470-6
Inkjet printing of two-dimensional transition metal chalcogenides (TMDs) is promising for low-cost, large-scale flexible electronics, yet challenges persist due to poor crystallinity and toxic solvents. Here, we report a green ink formulation using zwitterionic cocamidopropyl betaine (CAB) as a dispersant and surfactant for liquid-phase exfoliation of single-crystalline TMDs in water and isopropanol (IPA). The dispersions contain no additives or binders, enabling direct production of stable (over one month) and concentrated (2 mg/mL) inks for MoS2, MoTe2, WS2, WSe2, and WTe2. Fully-printed MoSe2/CAB humidity sensors exhibit superior sensitivity (ΔI/I0 = 468.1) and rapid response/recovery times (27 s/0.42 s) under bending. Inkjet-printed WTe2/CAB pads on 6-μm-thick substrates demonstrate exceptional mechanical stability, with resistance variations of 1.4% under single bending and 2% after 1,000 cycles, and acquire high-quality electrocardiogram (ECG) and electromyography (EMG) signals. This strategy enables scalable fabrication of TMD-based flexible electronics, advancing industrial integration.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61101-8
Phenolic compounds are typical refractory organic pollutants in coal chemical coking wastewater, posing significant risks to ecosystems and human health. Conventional treatment methods are inefficient, necessitating advanced oxidation processes (AOPs). Here, we report a low-cost Fe/N–C catalyst synthesized from coal-tar pitch, a common by-product of the coal chemical industry, via a self-assembly and pyrolysis strategy using graphitic carbon nitride (g-C3N4) as a template and nitrogen source, with dicyandiamide as an auxiliary nitrogen source and FeCl3·6H2O as the iron precursor. The resulting nitrogen-doped carbon nanosheets possess abundant defects (sp3-C/sp2-C = 0.66) and atomically dispersed iron species. The Fe/N–C catalyst exhibits outstanding catalytic activity for peroxydisulfate (PDS) activation, achieving over 98% phenol degradation within 30 minutes and a 60% total organic carbon (TOC) removal rate. Mechanistic studies, including radical quenching and electron paramagnetic resonance (EPR) experiments, reveal that both radical and non-radical pathways contribute to phenol degradation, with singlet oxygen (1O2) as the primary reactive oxygen species. Electrochemical analyses demonstrate that atomically dispersed Fe sites significantly enhance interfacial electron transfer. Post-reaction characterization indicates the consumption of pyrrolic-N, C=O, and carbon defects as active sites, while graphitic-N and Fe–N structures remain stable, confirming the catalyst's stability. This work provides an economical route to convert coal-tar pitch into high-performance catalytic materials for efficient water treatment, embodying the circular economy concept of waste-to-resource utilization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3784-9
Symmetry-breaking charge separation (SB-CS) is a fundamental process in natural photosynthesis and holds promise for organic semiconductor applications. However, the influence of SB-CS on excited-state chirality has remained unexplored. Here, we employ femtosecond time-resolved circularly polarized luminescence (TRCPL) and transient absorption (TA) spectroscopy to investigate the excited-state chirality dynamics of a chiral perylenediimide bichromophore (Cy-PDI 2). Our results reveal that the locally excited (LE) state decays to a symmetry-breaking charge-separated (SB-CS) state within 88 ps in tetrahydrofuran (THF), while this process is strongly quenched in toluene (TOL). Time-dependent emission dissymmetry factor g_lum(t) extracted from TRCPL kinetics demonstrates a one-order-of-magnitude enhancement of circularly polarized luminescence after SB-CS, directly reflecting the asymmetry of electron cloud distribution on an ultrafast timescale. This work provides the first direct observation of excited-state chirality evolution during SB-CS and proposes a mechanistic framework. Our findings offer deeper insight into the origin of excited-state chirality, which is crucial for understanding efficient energy transfer, enantiospecific recognition, and asymmetric catalysis in biological and chemical systems.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025022302
The escalating environmental contamination by mercury ions (Hg2+) poses severe risks to ecosystems and human health, necessitating the development of rapid, sensitive, and cost-effective detection methods. In this study, Fe1-xS@CNT composite nanozymes were synthesized via a straightforward solvothermal approach. The nanozymes exhibit uniform morphology, structural stability, and significant peroxidase (POD)-like activity. The incorporation of carbon nanotubes (CNT) facilitates electron transfer, enhancing the Fenton reaction between Fe2+/Fe3+ to generate abundant reactive oxygen species (ROS), primarily hydroxyl radicals (·OH) and superoxide anions (·O2−). The synergistic action of these ROS and photogenerated holes (h+) promotes the oxidation of 3,3',5,5'-tetramethylbenzidine (TMB) to a blue-colored product (oxTMB), establishing a colorimetric system of Fe1-xS@CNT + H2O2 + TMB. The specific binding of S2− on the nanozyme surface to Hg2+ inhibits POD activity, reducing the absorbance of the system. This principle was harnessed to develop a colorimetric method for Hg2+ quantification in environmental water samples. The method demonstrates a linear range of 0.1–500 μg·L−1 and a limit of detection (LOD) of 0.04 μg·L−1. Validation in real water samples (campus and tap water) showed recoveries between 94.4% and 111.1% with relative standard deviations (RSD) below 3.0%, comparable to atomic fluorescence spectrometry. The method offers advantages of simplicity, rapid analysis, and naked-eye visibility, providing a novel approach for on-site monitoring of heavy metal pollutants.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606014
Microplastics, as emerging environmental pollutants, can adsorb psychotropic drugs in aquatic environments, facilitating their migration and transformation, ultimately posing ecological risks. This study investigated the adsorption behavior and mechanisms of four common microplastics—polyethylene (PE), polypropylene (PP), polystyrene (PS), and polyvinyl chloride (PVC)—each with a particle size of 50 μm, toward three psychoactive drugs: diazepam, fluoxetine, and mianserin. Adsorption kinetics, isotherms, and the effects of pH and salinity were examined. Kinetic data fitted well to a pseudo-second-order model, indicating chemisorption as the rate-limiting step. Isotherm analysis using Langmuir and Freundlich models revealed that PE exhibited the highest affinity for fluoxetine, PP for mianserin, and PVC for diazepam, while PS showed linear adsorption for fluoxetine, suggesting partitioning. The adsorption of diazepam was maximal at pH 6.5–8.5, typical of natural surface waters, and increased with NaCl concentration, indicating that non-electrostatic interactions dominate and that higher ionic strength enhances adsorption. Mechanistic insights suggest that hydrophobic interactions, hydrogen bonding, π-π interactions (for PS), and halogen bonding (for fluoxetine) contribute to adsorption. These findings highlight the potential of microplastics to act as vectors for psychoactive drugs, necessitating further research on their environmental fate and ecological implications.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606010
Dissolved oxygen (DO) is a critical factor controlling endogenous phosphorus (P) migration in eutrophic waters. Existing oxygenation technologies suffer from high energy consumption and sediment disturbance, necessitating low-disturbance, pH-stable strategies that avoid additional nitrogen and P loads. This study evaluated an oxygen-loaded porous material (OLPM) for inhibiting sediment P release using laboratory microcosms with natural eutrophic water samples. DO microprofiles across the sediment-water interface (SWI) were measured with microelectrodes; diffusive gradients in thin films (DGT) resolved Fe, S, and P distributions; and sequential extraction quantified sediment P fractions. Results showed that OLPM coverage increased surface sediment DO concentration by 6.58-fold and DO penetration depth by 1.33-fold (16.8 mm). Overlying water total phosphorus (TP) decreased by 93.79%, and sediment interstitial phosphate (PO4-P) decreased by up to 45.75%. The SWI TP exchange flux reversed from +0.0068 mg/(m2·d) to -0.014 mg/(m2·d), shifting the system from a P source to a P sink. Sediment P fractionation revealed a 5.22% increase in stable Res-P and a 4.48% decrease in labile NaHCO3-P. Mechanistically, OLPM enhanced iron oxidation (Fe2+ reduced by 59.62%) and suppressed sulfate reduction (S2- homogenized at low levels), promoting P immobilization via Fe-S coupling. The material effectively inhibits endogenous P release through interfacial DO regulation without altering pH, offering a promising approach for eutrophication management.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606009
The escalating volume of municipal solid waste in China necessitates effective disposal strategies. Industrial kiln co-processing offers a promising route, but high-temperature decomposition of chlorinated components releases HCl and Cl2, causing severe equipment corrosion and operational issues. This study investigates the high-temperature dechlorination performance of fly ash and red mud, two abundant industrial solid wastes, as potential dechlorination agents. Using a high-temperature tube furnace system, dechlorination efficiencies were evaluated across 600–900 °C. At 700 °C, fly ash achieved a peak dechlorination efficiency of 93.33%, while red mud reached 88.61%. However, efficiencies declined with further temperature increase, dropping to 65.6% and 58.27% at 900 °C for fly ash and red mud, respectively. To enhance performance at higher temperatures, fly ash was modified via alkali (NaOH) treatment. The modification increased surface roughness and porosity, disrupted Si-O-Si and Si-O-Al networks, and exposed active sites. Consequently, the alkali-modified fly ash exhibited a peak dechlorination efficiency of 94.98% at 800 °C, a 23.08% improvement over unmodified fly ash (71.9%). These findings demonstrate the technical feasibility of utilizing solid wastes as dechlorination agents, offering a dual benefit of waste valorization and cost-effective high-temperature gas purification. The study provides a foundation for scaling up this approach in industrial kiln applications, contributing to sustainable waste management and reduced environmental impact.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511087
Identifying the sources and driving factors of heavy metals (HMs) in paddy soils around mining areas is crucial for safeguarding regional agricultural production and food security. This study focused on paddy soils near a mining area in southern Jiangxi Province, integrating Spearman correlation analysis, positive matrix factorization (PMF), and extreme gradient boosting (XGBoost) coupled with SHapley Additive exPlanations (SHAP) to quantitatively apportion potential ecological risks, pollution sources, and driving factors. Results showed that mean concentrations of Pb, Ni, and Cu exceeded the soil background values of Jiangxi Province, except for Cr. The mean comprehensive potential ecological risk index (RI) was 17.4, with 25.7% of sampling sites exhibiting moderate risk, and Ni being the primary ecological risk factor. Source apportionment identified three main sources: natural background (51.1%), industrial and mining activities (26.6%), and a mixed source of agricultural activities and traffic emissions (22.3%). Spatial variation of Cr, Cu, and Ni was predominantly governed by soil physicochemical properties (Fe and P contents), whereas Pb distribution was significantly influenced by industrial and mining activities. The combination of PMF and XGBoost-SHAP effectively delineated sources and driving factors, providing a scientific basis for targeted soil management and pollution control in mining-affected agricultural regions.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025040705
Chromium is a common environmental metal pollutant. Shewanella oneidensis MR-1 can generate extracellular electrons, facilitating the reduction of Cr(VI) to Cr(III), thereby mitigating its toxicity. Both biochar and electroactive dissolved organic matter (e-DOM) regulate extracellular electron transfer during Cr(VI) bioreduction. In practice, surface DOM on biochar can detach and enter the environment, while the biochar matrix (BCM) remains the predominant form and coexists with e-DOM. However, the combined effects of BCM and e-DOM on microbial Cr(VI) removal are unclear. This study investigated the individual and combined impacts of biochar matrix and AQDS (a model e-DOM) on Cr(VI) reduction by S. oneidensis MR-1. Results showed that biochar matrix or AQDS alone promoted Cr(VI) removal, primarily by accelerating electron transfer during the fast reduction phase. However, when both were added, an antagonistic effect was observed, attributed to increased repulsive forces between the biochar matrix-AQDS complex and the bacterial cells, which inhibited electron transfer to Cr(VI). This research elucidates the electrochemical interactions between biochar matrix and e-DOM, providing a theoretical basis for biochar applications in environmental remediation and risk assessment.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202607004
Pelletizing technology is widely applied in biomass and coal fuel processing, offering advantages in transport, storage, and energy density. Coal gasification fine slag (CGFS), a carbon-rich coal-based solid waste, holds potential as a fuel. This study prepared centimeter-scale composite pellets by blending CGFS with various biomass types under 6 MPa at room temperature for 2 minutes. Combustion and emission characteristics were investigated using a self-developed flat-flame macro-thermogravimetric reactor simulating high heating rate conditions. Results showed that biomass type significantly influenced combustion due to chemical composition differences. Introducing biomass altered fuel particle composition, enhancing combustion rates of single-component fuels by 3–5 times during volatile combustion. Co-combustion reduced NOx and CO emissions by over 50% compared to pure CGFS. Higher biomass ratios accelerated volatile release and shortened burnout time but increased NO emissions due to higher volatile nitrogen content. Conversely, CO emissions decreased due to improved char combustion conditions. These findings provide critical experimental support for optimizing clean and efficient solid fuel production from CGFS and biomass.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3892-2
Single-atom co-catalysts on semiconductor substrates offer a cost-efficient route to enhance photocatalytic performance with minimal precious metal loading. However, precise tuning of local coordination environments and construction of efficient single-atom co-catalysts remain challenging for overall water splitting. Here, we employ an icing-assisted photochemical reduction strategy to anchor atomically dispersed Pt species as hydrogen evolution co-catalysts on Al3+-doped SrTiO3 (Pt SA-STO). The optimized Pt SA-STO exhibits remarkable activity, with hydrogen and oxygen evolution rates of 13.62 and 6.71 mmol h−1 g−1, respectively, and a turnover frequency (TOF) of 2114.5 h−1. We pioneer the use of nuclear magnetic resonance (NMR) spectroscopy to quantitatively track the temporal evolution of Pt4+ to Pt2+ under continuous irradiation during the icing-assisted photoreduction. Advanced characterizations and theoretical calculations confirm that single-atom Pt co-catalysts facilitate directional transfer and extraction of photogenerated charge carriers, effectively suppressing surface recombination. This work provides insights into designing novel single-atom co-catalysts by deepening understanding of electronic configurations and active sites in photocatalytic overall water splitting.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608009
To investigate the flow and heat transfer characteristics of natural draft direct air-cooling towers (NDC) for large coal-fired power generating units, a three-dimensional CFD numerical model covering major plant buildings, air-cooled radiators, and ambient wind fields was established based on the NDC systems of a 2×660 MW unit of a power plant. The influences of meteorological factors, including ambient wind speed, ambient temperature, and ambient wind direction, as well as regulation measures such as rolling shutters, louvers, and bypass windows on the heat dissipation performance of NDC towers were systematically analyzed. The results demonstrate that ambient wind speed acts as the dominant factor governing the performance of the NDC system. As wind speed rose, the uneven distribution of air intake volume and heat dissipation among each cooling delta increased remarkably, which elevated the unit back pressure, and the upstream tower suffered more severe impacts than the downstream one. Ambient temperature exerted a slight effect on circumferential flow distribution, yet substantially changed the overall back pressure of the system. In terms of regulation strategies, closing rolling shutters in the windward zone and reducing the opening of partial louvers can improve air flow redistribution to a certain extent, but will reduce the total air flow rate and total heat dissipation of the entire tower. By contrast, bottom bypass windows can effectively optimize the air intake on the leeward side and boost heat dissipation under high-wind operating conditions, whereas top bypass windows deliver only limited improvement effects. This research can provide fundamental data and technical references for the optimal design, operational regulation, and energy-saving retrofitting of large NDC units.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2026022402
Graphene oxide–silver nanoparticle (GO-AgNPs) nanocomposites synergistically combine the high specific surface area and biocompatibility of graphene oxide with the potent antibacterial and optical properties of silver nanoparticles. This review systematically examines current synthetic strategies—physical, chemical, and biological—and their influence on nanocomposite morphology, loading efficiency, and stability. The biomedical applications of GO-AgNPs are critically analyzed, focusing on antimicrobial activity, anticancer therapy, drug delivery, and biosensing. Mechanistic insights reveal that antimicrobial action involves membrane disruption, oxidative stress, and damage to biomolecules, while anticancer effects are mediated through reactive oxygen species (ROS) generation. The review also addresses challenges such as AgNP aggregation and stability, which are mitigated by GO support. Future directions emphasize the development of multifunctional nanomedicine platforms, with a need for standardized toxicity assessments and scalable synthesis. This comprehensive overview aims to guide further research and clinical translation of GO-AgNPs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4033-1
Photodetectors are critical components in modern optoelectronic systems, underpinning applications in optical communication, low-altitude economy, environmental monitoring, and national defense. Layered two-dimensional (2D) materials such as MoS2, WS2, black phosphorus (BP), and ReS2 have attracted extensive attention due to their remarkable electronic and optical properties, including facile mechanical exfoliation and tunable characteristics via thickness engineering. The absence of dangling bonds enables the construction of van der Waals (vdW) heterostructures free from lattice-matching constraints, promoting efficient charge transport, enhanced light absorption, and suppressed dark current. Among layered materials, semimetals such as graphene, PdTe2, MoTe2, and TaIrTe4 exhibit narrow or zero bandgaps, enabling ultrabroadband spectral responses from ultraviolet (UV) to terahertz (THz). ZrTe3, a layered gapless semimetal, demonstrates pronounced carrier transport features, including robust excitons and ultrafast carrier relaxation times, making it an ideal candidate for photodetection. However, pure ZrTe3-based photodetectors suffer from substantial dark current due to the absence of an energy bandgap, degrading signal-to-noise ratio and specific detectivity (D*). This work reports a high-performance broadband photodetector based on a ZrTe3/CuInP2Se6 heterostructure. By exploiting an asymmetric contact configuration that introduces a Schottky barrier, the device effectively suppresses dark current while enhancing photoresponse. The photodetector exhibits broad spectral sensitivity from UV to near-infrared (355–1177 nm), microsecond-level response speed, and high responsivity and specific detectivity. Beyond conventional photodetection, an optoelectronic information encryption-decryption application is demonstrated, where modulated light and bias voltage serve as dual input channels to encode and decode ASCII signals. This study resolves the challenge of high dark current in semimetal-based photodetectors and introduces a multifunctional platform for secure optoelectronic communication, highlighting the potential of ZrTe3 for next-generation photonic and quantum information technologies.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4132-y
Manganese-iron-based mixed polyanionic cathodes are promising for sodium-ion batteries (SIBs) due to high energy density and operating voltage, but suffer from Jahn-Teller distortion of Mn3+ that degrades cycling stability. Here, a structural modulation strategy via Mg2+ doping is reported. Electrochemically inert Mg2+ forms stronger chemical bonds, adjusts lattice parameters, and suppresses Jahn-Teller distortion, enhancing structural stability. Mg2+ also widens sodium-ion diffusion channels, improving diffusion kinetics. Additionally, an in-situ three-dimensional carbon nanotube (CNT) conductive network boosts electronic conductivity. The resulting NFMPP-Mg@CNTs cathode delivers a discharge capacity of 126 mAh g−1 at 0.1 C (near theoretical 129 mAh g−1), retains 80% capacity after 3000 cycles at 0.5 C, and achieves an energy density of 401 Wh kg−1, among the highest reported for mixed phosphate systems. Ex-situ XPS and first-principles calculations confirm that Mg2+ resists geometric distortion by enhancing lattice stability and widening Na+ diffusion pathways (migration barrier reduced from 0.566 to 0.398 eV). This work provides a viable route for high-energy, long-life SIB cathodes suitable for large-scale energy storage.